Accessory
Application
Publications No.
All 23607
Issue Date
CD CHANGER
ATTACHMENT
INSTALLATION
INSTRUCTIONS
2003-2004 PILOT
MAY 2002
PARTS LIST
CD Changer Attachment Kit (sold separately):
P/N 08B26-S9V-100
8 Wire ties
Right base bracket
Left base bracket
4 Washer-screws, 4 x 8 mm
2 Wire clips
CD Changer (sold separately):
P/N 08A26-1B1-100
Right changer bracket
Left changer bracket
CD changer
4 Washer-screws, 4 x 6 mm
(Not used)
BUS Cable
Adhesive seal sheet
Locking covers
4 Flange bolts, 6 x 12 mm
4 Flange nuts
CD magazine
2 EPT seals (Black)
Owner’s Manual
2 Cushion tapes (Gray)
Small wire tie
(Not used)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
All 23607 (0205)
08B26-S9V-1000-91
1 of 8
•
Remove the center panel (four self-tapping
screws, two clips, and unplug the vehicle
accessory power outlet).
4. On the driver’s side of the vehicle, gently pull the
center console lower cover out toward you to
release the seven clips and remove the center
console lower cover. Take care not to damage the
clips.
CLIPS (2)
DRIVER’S
SEAT
CENTER
PANEL
DRIVER’S CENTER
CONSOLE LOWER
COVER
SELF-
TAPPING
SCREW
VEHICLE
CONNECTOR
CLIPS (7)
5. Remove the driver’s seat front cover by pulling it
toward you. Take care not to damage the clips.
•
Remove the four screws that fasten the audio
brackets. Pull the audio unit/heater control unit
out toward you, unplug the vehicle connectors
and antenna lead.
DRIVER’S
SEAT
ANTENNA
LEAD
HEATER
CONTROL
UNIT
AUDIO
BRACKET
VEHICLE
CONNECTOR
DRIVER’S
SEAT FRONT
COVER
AUDIO
BRACKET
SCREW
CLIPS (4)
AUDIO UNIT
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
All 23607 (0205)
3 of 8
Routing the BUS cable
6. Route the BUS cable.
Without Navigation Unit:
With Navigation Unit:
•
Route the BUS cable from the dashboard
opening to the driver’s floor. Pull out the end of
BUS cable 30 mm from the end of the vehicle
20-pin connector, and secure the BUS cable to
the vehicle harness with wire ties.
•
Route the BUS cable from the dashboard
opening to the driver’s floor. Pull out the end of
BUS cable 30 mm from the end of the vehicle
20-pin connector, and secure the BUS cable to
the vehicle harness and frame with three wire
ties.
•
•
Cut the EPT seal in half. Attach 1/2 of the EPT
seal on the edge of vehicle body to protect the
BUS cable. Before attaching the tape, wipe the
surface with isopropyl alcohol.
Secure the BUS cable on the vehicle frame
with two wire ties.
VEHICLE
BUS CALBE
20-PIN
14-PIN
CONNECTOR
CONNECTOR
WIRE TIE
VEHICLE
HARNESS
EPT SEAL
Clean with isopropyl
FRAME
alcohol.
WIRE TIE
BUS
CABLE
VEHICLE
HARNESS 20-PIN
CONNECTOR
30 mm
CENTER
PANEL
OPENING
FRAME
WIRE
TIE
WIRE
TIE
BUS CABLE
14-PIN
CONNECTOR
30 mm
FRAME
BUS
CABLE
4 of 8
All 23607 (0205)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
7. Using 1/2 of an EPT seal attach it to the frame at
the location shown. Measure 450 mm from the
end of the BUS cable to the frame, then bundle up
the excess cable and secure it to the vehicle with
three wire ties.
10. Install the right and left base brackets to the
driver’s seat raisers using two 6 x 12 mm flange
bolts for each bracket. Do not tighten the bolts yet.
6 x 12 mm
FLANGE
BOLT
EPT SEAL
WIRE
Cut in half.
TIE
FRAME
RIGHT
LEFT
BASE
BASE
BRACKET
BRACKET
450 mm
Installing the CD Changer
11. Carefully unpack the CD changer. Remove the
three shipping clips, and discard the shipping
cover. Install an adhesive seal (included with the
CD changer kit) over each of the three clips holes.
Save the shipping clips for your customer in the
event the unit needs to be serviced.
Bundle up
the excess
BUS cable.
Secure to the
vehicle harness.
BUS CABLE
8. Attach 1/2 of an EPT seal to the edge of the
frame in the area shown.
SHIPPING CLIPS (3)
1/2 EPT seal
(Clean with
isopropyl
alcohol.)
FRAME
SHIPPING COVER
(Discard.)
FLOOR
CARPET SLIT
ADHESIVE SEALS (3)
BUS
CABLE
50 mm
Cut
here.
9. Near the edge of the driver’s seat raiser make a
50 mm slit in the floor carpet with a utility knife.
Route the BUS cable under the floor carpet and
out the slit near the seat raiser.
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
All 23607 (0205)
5 of 8
12. Visually check the position of the spring adjusting
pin on both sides of the CD changer. If the spring
adjusting pins are not in the horizontal (H)
15. Attach one cushion tape to the rear of the CD
changer leaving half of the cushion tape extended
past the CD changer. Using scissors, cut the
cushion at the end of the CD changer. Fold the
ends down and around the end of the CD
changer.
position, move the pins to the horizontal (H)
position by sliding them up with your fingers.
SPRING
ADJUSTING PIN
(H: HORIZONTAL)
(V: VERTICAL)
LEFT LOCKING
COVER
(Included with CD
Changer kit)
RIGHT BASE
BRACKET
LEFT BASE
BRACKET
RIGHT
LOCKING
COVER
FLANGE
NUTS (4)
(Included with
CD Changer
kit)
SPRING
ADJUSTING
PINS
LEFT CHANGER
BRACKET
RIGHT
CUSHION TAPE
CHANGER
BRACKET
CD CHANGER
13. Remove the adhesive backing from the “L” and “R”
locking covers, and attach them to the sides of
the CD changer. Align the diagonally opposite
holes with the H and V positions.
CUSHION
TAPE
LEFT CHANGER
BRACKET
14. Install the right changer bracket to the CD
changer using two 4 x 8 mm washer-screws, and
the two wire clips. Install the left changer bracket
to the CD changer using two 4 x 8 mm washer-
screws.
16. Attach the cushion tape to the top of the left
changer bracket align the cushion tape already
attached. Fold the cushion tape around the CD
changer.
17. Insert the studs of the left and right base brackets
into the holes in the left and right changer
brackets, then install the four flange nuts on the
end of each stud. Tighten the four flange nuts and
four bracket bolts in step 10 on the bracket plates.
4 x 8 mm
WASHER-
SCREW
LEFT
CHANGER
BRACKET
WIRE
CLIP
WIRE
CLIP
RIGHT
CHANGER
4 x 8 mm
WASHER-
SCREW
BRACKET
FRONT
6 of 8
All 23607 (0205)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
18. Plug the BUS cable connector into the CD
changer connector. Bundle up any excess BUS
cable and attach it to the CD changer bracket with
the two wire clips installed in step 14.
With Cassette Player:
AUDIO UNIT
BUS CABLE
VEHICLE
20-PIN
CONNECTOR
CASSETTE
PLAYER
WIRE CLIP
ANTENNA
LEAD
BUS CABLE
14-PIN
CONNECTOR
CD CHANGER
With CD/Cassette Tuner:
(With Navigation Unit)
19. At the dashboard area, plug the BUS cable 14-pin
connector, the vehicle connectors, and the
antenna lead into the rear of the audio unit.
AUDIO UNIT
With Pocket:
AUDIO UNIT
BUS CABLE
14-PIN
CONNECTOR
BUS CABLE
14-PIN
CONNECTOR
VEHICLE
20-PIN
CONNECTOR
ANTENNA
LEAD
VEHICLE
16-PIN
POCKET
VEHICLE
20-PIN
CONNECTOR
CONNECTOR
ANTENNA
LEAD
VEHICLE
22-PIN
CONNECTOR
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
All 23607 (0205)
7 of 8
20. Slide the audio unit into the center panel opening,
and reinstall the four screws.
21. Check that all wire harnesses are routed properly
and all connectors are plugged in.
Without Navigation Unit:
22. Reinstall all removed parts.
23. Place shipping clips in a plastic bag and put the
bag in the glove box.
VEHICLE
CONNECTOR
BUS CABLE
CONNECTOR
ANTENNA
LEAD
24. Reconnect the negative cable to the battery.
25. Enter the customer’s radio anti-theft code, and
reset the radio station presets.
AUDIO
UNIT
NOTE: Whenever the battery is disconnected, the
driver’s window AUTO function is disabled.
26. Start the engine. Push down on the driver’s
window switch until the window is fully open.
27. Pull up on the driver’s window switch to close the
window completely, then hold the switch for two
seconds.
28. Test the AUTO window function.
29. Do the idle learn procedure.
SCREWS
(reused)
– Make sure all electrical items are turned off.
AUDIO
BRACKET
– Start the engine. Hold the engine speed at 3,000
rpm with no load (in Park or Neutral) until the
radiator fan comes on.
With Navigation Unit:
– Let the engine idle for about 5 minutes with the
throttle fully closed and with all electrical items
off.
ANTENNA
LEAD
BUS
CABLE
VEHICLE
HARNESS
NOTE: If the radiator fan comes on during this step,
the time when it is operating must not be included in
the 5 minutes.
VEHICLE
HARNESS
HEATER
CONTROL
AUDIO UNIT
SCREW
(reused)
8 of 8
All 23607 (0205)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
|