Operator’s Manual
Models
5021 R (531309638) 6210530X37NA
5021 E (531309639) 6210540X37NA
Read and keep this book for future reference.
This book contains important information on
Safety, Assembly, Operation, and Maintenance.
Product Imformation
The owner must be certain that all the product information
is included with the unit. This information includes the
INSTRUCTION BOOKS, REPLACEMENT PARTS, and
WARRANTIES. This information must be included to make
sure state laws and other laws are followed.
2007 - 07
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
Operating Symbols and their meanings
This manual contains safety information to
make you aware of the hazards and risks
associated with snow throwers, and how to avoid them.
The snow thrower is designed and intended for removal
of snow, and should not be used for any other purpose. It
is important that you read and understand these
instructions, and anyone operating the equipment read
and understand these instructions.
These symbols are used on your equipment and defined in
your operating manual. It is important that you review and
understand the meanings. Failure to understand the
symbols might result in harm to you.
Oil
WARNING
Foward
Neutral
Fuel
The engine exhaust from this product contains chemicals
known to the State of California to cause cancer, birth
defects, or other reproductive harm.
On Off
A signal word (DANGER, WARNING, or CAUTION) is used
with the alert symbol to indicate the likelihood and the
potential severity of injury. In addition, a hazard symbol may
be used to represent the type of hazard.
Primer bulb
Reverse
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
Throttle
Ignition On
Ignition Off
Ignition Key
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
Choke off
CAUTION indicates a hazard which, if not avoided,
might result in minor or moderate injury.
CAUTION, when used without the alert symbol,
indicates a situation that could result in damage to
the equipment.
Choke on
Stop
Hazard Symbols and the meanings
Push to engage
electric start
These symbols are used on your equipment and defined in
your operating manual. Review and understand the meanings.
The use of one of these symbols combined with a signal word
will alert you to potential hazards and how to avoid them.
Slow
Fast
Electric
Start
Safety Alert − Identifies safety information about
hazards that can result in personal injury.
Engine
Start
Engage
Traction
Operator’s Manual − Read and understand before
performing any activity or running equipment.
Engine Run
Rotating auger
Fire
Auger Collector
Auger Clutch
Engine Off
Engage
Rotating impeller
Explosion
Shock
Toxic fumes
Hot Surface
Drive Clutch
Disengage
Rotating gears
Thrown objects
Never reach into
rotating parts.
Discharge Chute
Chute Deflector
Recommended ear
protection for
extended use.
Keep a safe distance
from the equipment.
DOWN
LEFT
RIGHT
UP
Shut off engine and remove spark plug connector
before performing maintenance or repair work.
3
1741491
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
WARNING: This machine is capable of amputating hands and feet and throwing objects. Read these safety
rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe per-
sonal injury or death to you, or bystanders, or damage to property or equipment. The triangle
signifies important cautions or warnings which must be followed.
in text
Safe Operation Practices for Snowthrowers
As Recommended By: American National Standards Institute (ANSI)
IMPORTANT: Safety standards require operator presence
controls to minimize the risk of injury. Your snowthrower is
equipped with such controls. Do not attempt to defeat the
function of the operator presence control under any circum-
stances.
5. Use extension cords and receptacles as specified by the
manufacturer for all units with electric drive motors or
electric starting motors.
6. Adjust the collector housing height to clear gravel or
crushed rock surfaces.
7. Never attempt to make any adjustments while the engine
(motor) is running (except when specifically recom-
mended by manufacturer).
8. Let engine (motor) and snowthrower adjust to outdoor
temperatures before starting to clear snow.
9. Always wear safety glasses or eye shields during oper-
ation or while performing an adjustment or repair to pro-
tect eyes from foreign objects that may be thrown from
the machine.
Training
1. Read, understand, and follow all instructions on the ma-
chine and in the manuals before operating this unit. Be
thoroughly familiar with the controls and the proper use of
the equipment. Know how to stop the unit and disengage
the controls quickly.
2. Never allow children to operate the equipment. Never
allow adults to operate the equipment without proper in-
struction.
Operation
3. Keep the area of operation clear of all persons, particular-
ly small children and pets.
1. Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
2. Exercise extreme caution when operating on or crossing
gravel drives, walks or roads. Stay alert for hidden haz-
ards or traffic.
3. After striking a foreign object, stop the engine (motor),
remove the wire from the spark plug, disconnect the cord
on electric motors, thoroughly inspect snowthrower for
any damage, and repair the damage before restarting and
operating the snowthrower.
4. If the unit should start to vibrate abnormally, stop the en-
gine (motor) and check immediately for the cause. Vibra-
tion is generally a warning of trouble.
4. Exercise caution to avoid slipping or falling especially
when operating in reverse.
Preparation
1. Thoroughly inspect the area where the equipment is to be
used and remove all doormats, sleds, boards, wires, and
other foreign objects.
2. Disengage all clutches and shift into neutral before start-
ing the engine (motor).
3. Do not operate the equipment without wearing adequate
winter outer garments. Wear footwear that will improve
footing on slippery surfaces. Avoid loose fitting clothing
that can get caught in moving parts.
5. Stop the engine (motor) whenever you leave the operat-
ing position, before unclogging the collector/impeller hous-
ing or discharge chute and when making any repairs,
adjustments, or inspections.
4. Handle fuel with care; it is highly flammable.
a. Use an approved fuel container.
6. When cleaning, repairing, or inspecting, make certain the
collector/impeller and all moving parts have stopped. Dis-
connect the spark plug wire and keep the wire away from
the spark plug to prevent accidental starting.
7. Do not run the engine indoors, except when starting the
engine and for transporting the snowthrower in or out of
the building. Open the outside doors; exhaust fumes are
dangerous (containing CARBON MONOXIDE, an ODOR-
LESS and DEADLY GAS).
8. Exercise extreme caution when operating on slopes. Do
not attempt to clear steep slopes.
9. Never operate the snowthrower without proper guards,
plates, or other safety protective devices in place and
working.
b. Never add fuel to a running engine or hot engine.
c. Fill fuel tank outdoors with extreme care. Never fill fuel
tank indoors. Replace fuel cap securely and wipe up
spilled fuel.
d. Never fill containers inside a vehicle or on a truck or
trailer bed with a plastic liner. Always place containers
on the ground, away from your vehicle, before filling.
e. When practical, remove gas−powered equipment from
the truck or trailer and refuel it on the ground. If this is
not possible, then refuel such on a trailer with a porta-
ble container, rather than from a gasoline dispenser
nozzle.
f. Keep nozzle in contact with the rim of the fuel tank or
container opening at all times, until refueling is com-
plete. Do not use a nozzle lock−open device.
10.Never direct the discharge toward people or areas where
property damage can occur. Keep children and others
away.
g. Replace gasoline cap securely and wipe up spilled fuel.
h. If fuel is spilled on clothing, change clothing immediate-
ly.
1741506
11.Do not overload the machine capacity by attempting to
clear snow at too fast a rate.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
12.Never operate the machine at high transport speeds on
Service, Maintenance And Storage
1. Check shear bolts and other bolts at frequent intervals for
proper tightness to be sure the equipment is in safe work-
ing condition.
2. Never store the machine with fuel in the tank inside a
building where ignition sources are present such as hot
water and space heaters, or clothes dryers. Allow the en-
gine to cool before storing in any enclosure.
slippery surfaces. Look behind and use care when operat-
ing in reverse.
13.Disengage power to the collector/impeller when snow-
thrower is transported or not in use.
14.Use only attachments and accessories approved by the
manufacturer of the snowthrower (such as cabs, tire
chains, etc..).
3. Always refer to operator’s manual for important details if
the snowthrower is to be stored for an extended period.
4. Maintain or replace safety and instruction labels as
necessary.
5. Run the machine a few minutes after throwing snow to
prevent freeze−up of the collector/impeller.
6. If fuel is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.
7. Always observe safe refueling and fuel handling practic-
es when refueling the unit after transportation or storage.
8. Always follow the engine’s manual instructions for storage
preparations before storing the unit for both short and
long term periods,
15.Never operate the snowthrower without good visibility or
light. Always be sure of your footing and keep a firm hold
on the handles. Walk, never run.
16.Never touch a hot engine or muffler.
17.Never operate the snowthrower near glass enclosures,
automobiles, window wells, drop−offs, and the like without
proper adjustment of the snow discharge angle.
18.Never direct discharge at bystanders or allow anyone in
front of the unit.
19.Never leave a running unit unattended. Always disen-
gage the auger and traction controls, stop engine, and
remove keys.
20.Do not operate the unit while under the influence of alco-
hol or drugs.
21.Keep in mind the operator is responsible for accidents
occurring to other people or property.
9. Always follow the engine manual instructions for proper
start-up procedures when returning the unit to service.
22.Data indicates that operators, age 60 years and above,
are involved in a large percentage of power equipment−
related injuries. These operators should evaluate their
ability to operate the unit safely enough to protect them-
selves and others from injury.
23.DO NOT wear long scarves or loose clothing that could
become entangled in moving parts.
10.Maintain or replace safety and instruction labels as
necessary.
11.Keep nuts and bolts tight and keep equipment in good
condition.
12.Never tamper with safety devices. Check their proper
operation regularly and make necessary repairs if they
are not functioning properly.
24. Snow can hide obstacles. Make sure to remove all ob-
stacles from the area to be cleared.
13.Components are subject to wear, damage, and deteriora-
tion. Frequently check components and replace with
manufacturer’s recommended parts, when necessary.
14.Check control operation frequently. Adjust and service as
required.
15.Use only factory authorized replacement parts when mak-
ing repairs.
16.Always comply with factory specifications on all settings
and adjustments.
17.Only authorized service locations should be utilized for
major service and repair requirements.
18.Never attempt to make major repairs on this unit unless
you have been properly trained. Improper service pro-
cedures can result in hazardous operation, equipment
damage and voiding of manufacturer’s warranty.
Children
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the unit
and the operating activity. Never assume that children will re-
main where you last saw them.
1. Keep children out of the area and under the watchful care
of another responsible adult.
2. Be alert and turn off if children enter the area.
3. Never allow children to operate the unit.
4. Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
Clearing A Clogged Discharge Chute
19.Check shear bolts (pins) and other bolts at frequent inter-
vals for proper tightness to be sure the equipment is in
safe working condition.
Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with
snowthrowers. Never use your hand to clean out the dis-
charge chute.
To clear the chute:
1. SHUT OFF THE ENGINE.
Emissions
1. Engine exhaust from this product contains chemicals
known, in certain quantities, to cause cancer, birth de-
fects, or reproductive harm.
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
2. If available, look for the relevant Emissions Durability
Period and Air Index information on the engine emissions
label.
3. Always use a clean out tool, not your hands.
1741491
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
RULES FOR SAFE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
HAZARD SYMBOLS AND THE MEANINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
OPERATING SYMBOLS AND THEIR MEANINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SAFE OPERATING PRACTICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OWNER’S INFORMATION/WARRANTY STATEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PARTS BAG CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . 11
TOOLS REQUIRED FOR ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
HOW TO REMOVE THE SNOWTHROWER FROM THE CARTON . . . . . . . . . . . . . . . 11
HOW TO ASSEMBLY THE HANDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ADD OIL TO THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
ADD FUEL TO THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
BEFORE YOU OPERATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
KNOW YOUR SNOWTHROWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
HOW TO CONTROL SNOW DISCHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
HOW TO THROW SNOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
HOW TO STOP DISCHARGING SNOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
HOW TO MOVE FORWARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
BEFORE STARTING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
HOW TO STOP THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
HOW TO START THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
HOW TO START A COLD ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
HOW TO START A WARM ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
HOW TO START A WARM ENGINE WITH A FROZEN STARTER . . . . . . . . . . . . . . . 17
HOW TO CLEAR A CLOGGED DISCHARGE CHUTE . . . . . . . . . . . . . . . . . . . . . . . . . 17
SNOW THROWING TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
EMISSIONS CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
GENERAL RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
ENGINE POWER RATING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
AFTER EACH USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
HOW TO REMOVE THE TOP COVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
LUBRICATION BEFORE STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
HOW TO ADJUST THE AUGER CONTROL CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
HOW TO REMOVE THE BELT COVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
HOW TO REPLACE THE DRIVE BELT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
HOW TO REPLACE THE AUGER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
HOW TO ADJUST THE BRAKE PAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
HOW TO REPLACE THE SPARK PLUG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
HOW TO PREPARE THE SNOWTHROWER FOR STORAGE . . . . . . . . . . . . . . . . . . . 24
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
TROUBLESHOOTING CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1741506
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY DECALS
The safety decals below are on your unit. If any of
This unit has been designed and manufactured
to provide you with the safety and reliability you
would expect from an industry leader in outdoor
power equipment.
these decals are lost or damaged, replace them at
once. See your local dealer for replacements. These
labels are easily applied and will act as a constant
visual reminder to you, and others who may use the
equipment, to follow the safety instructions necessary
for safe, effective, operation.
Although reading this manual and safety instructions
it contains will provide you with the necessary basic
knowledge to operate this equipment safely and ef-
fectively, we have placed several safety labels on
the unit to remind you of this important information
while you are operating your unit.
NOTE: Engine operation and safety decals are
supplied by the engine manufacturer.
All WARNING, CAUTION, and instructional mes-
sages on your unit should be carefully read and
obeyed. Personal bodily injury can result when
these instructions are not followed. The information
is for your safety and it is important.
1741506
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY DECALS
Decals
REF NO PART NO.
DESCRIPTION
1
2
2
3
3
4
5
5
6
7
8
9
-----
* DECAL, EPA, MASS
761793MA
48X5638MA
1741524MA
1741525MA
1740048MA
1740372MA
1740366MA
69880MA
DECAL, ELECTRIC START, COVER UP (Used on Model 6210530x37NA 5021R Only)
DECAL, ELECTRIC START (Used on Model 6210540x37NA 5021E Only)
DECAL, DASH PANEL (Used on Model 6210530x37NA 5021R Only)
DECAL, DASH PANEL (Used on Model 6210540x37NA 5021E Only)
DECAL, HUSQVARNA
DECAL, HUSQVARNA 5021R (Used on Model 6210530x37NA 5021R Only)
DECAL, HUSQVARNA 5021E (Used on Model 6210540x37NA 5021E Only)
DECAL, WARNING HOT MUFFLER
761150MA
48X5642MA
70141MA
DECAL, AUGER CONTROL
DECAL, DANGER CHUTE
DECAL, DANGER AUGER, FOOT
1741506
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S INFORMATION
WARRANTY STATEMENT
SECTION 1: LIMITED WARRANTY
Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects
in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below:
Lifetime Warranty (Parts and Labor): All tiller tines and trimmer shafts against breakage. Proof of purchase required.
Lifetime Warranty (“PARTS ONLY” after initial warranty expiration): Ignition coils and modules on handheld product. Proof
of purchase required.
WARRANTY SCHEDULE FOR TURF CARE Equipment − Zero Turn Riders (New warranty applies to units sold after August
1, 2005. Also applies to units factory-equipped with R.O.P.S.
EZ Zero Turn Riders: 3 year consumer warranty or 600 hours of use (when used solely at the owner’s residence.)
EZ Zero Turn Riders: 1 year commercial warranty or 600 hours of use.
iZ, LZ & BZ Zero Turn Riders: 5 year consumer warranty or 1,500 hours of use (when used solely at the owner’s residence.)
iZ, LZ & BZ Zero Turn Riders: 1 year commerical warranty or 1,500 hours of use.
3 Year or 1,500 Hour Commercial Use Warranty: spindles on zero turn riders, hydraulic pumps and wheel motors.
Warranty Schedule for Turf Care Walk Behind Units − W, WG & WH Zero Turn Riders - 3 year consumer and commercial
warranty. New warranty applies to units sold after August 1, 2005. Also applies to units factory-equipped with R.O.P.S.
2 Year COMMERCIAL and CONSUMER Warranty: all Husqvarna ground-engaging commercial equipment.
WARRANTY SCHEDULE FOR CONSUMER TURF CARE EQUIPMENT:
2 Year Consumer Warranty: Automatic mower, all Residential Zero Turn Riders, all lawn, yard and garden tractors, all
noncommercial walk behind mowers, tillers, chain saws, trimmers, brushcutters, clearing saws, snow blowers, handheld blowers,
backpack blowers, hedge trimmers, electrical products and power-assist collection systems for noncommercial, nonprofessional,
noninstitutional or nonincome producing use, except as herein stated. All consumer product use must have been limited to the
owner’s residence.
WARRANTY SCHEDULE FOR CONSUMER FOREST & GARDEN EQUIPMENT:
2 Year Consumer Warranty: all consumer chain saws, trimmers, brushcutters, clearing saws, handheld blowers, backpack
blowers, hedge trimmers, and electrical products for noncommercial, nonprofessional, noninstitutional or nonincome producing
use, except as herein stated. All consumer product use must have been limited to the owner’s residence.
2 Year or 2,000 Hour & 1 Year or 1,000 Hour Warranty: Husqvarna Utility Vehicles
1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for noncommercial, nonprofessional, noninstitutional
or nonincome producing use. All 300 series trimmers, brushcutters, clearing saws, hovering trimmers, stick edgers, backpack
blowers, handheld blowers, hedge trimmers, power-assist collection systems for commercial, institutional, professional or income
producing purposes or use.
1 Year Conditional Component Warranty: Chain saw crankshafts for commercial/professional use (parts and labor). Saw must
be operated with Husqvarna XP 2 cycle oil.
90 Day Commercial Warranty: Automatic mower, chain saws, 100 series trimmers, power cutters, stump grinders, pole saws,
pole pruners, snow throwers, model series 580 & 600 walk-behind mowers, or any Husqvarna product used for commercial,
institutional, professional, municipality or income producing purposes or use except as otherwise provided herein.
Batteries: 1 year prorated limited warranty with 100% replacement during the first 6 months.
Rental Warranty: 90 days on all applicable professional equipment reference warranty time period charts located in the back of
the Retailer Warranty Policy & Procedure Manual.
Husqvarna Safety Apparel caries as 90-day warranty from the date of the customer’s original purchase for defects in material
and workmanship. Normal wear, tear or abuse is not covered under the warranty. Product must be returned to Charlotte with a
warranty claim form. All care and maintenance instructions must be followed as stated by the manufacturer on the care label. The
fit of the product apparel/boot is not covered under warranty.
30 Day Warranty: Replacement parts, accessories including bars and chains, tools and display items. Emission control system
components necessary to comply with CARB-TIER II and EPA regulations, except for those components which are part of engine
systems manufactured by third part engine manufactures for which the purchaser has received a separate warranty with product
at time of purchase.
SECTION 2: HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY
Husqvarna will repair or replace defective components without charge for parts or labor if a component fails because of a defect
in material or workmanship during the warranty period.
9
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S INFORMATION
WARRANTY STATEMENT
SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY
The following items are not covered by this warranty:
1. Normal customer maintenance items which become worn through normal regular use, including, but not limited to, belts, blades,
blade adapters, bulbs, clutches, clutch drums, filters, guide bars, lubricants, rewind springs, saw chain, spark plugs, starter
ropes and tines.
2. Natural discoloration of material due to ultraviolet light.
3. Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective manufacturer’s warranty
as provided in writing with the product information supplied at the time of purchase; all claims must be sent to the appropriate
manufacturer.
4. Lawn and garden attachments are covered by a third party which gives a warranty, all claims for warranty should be sent to the
manufacturer.
5. Commercial or consumer mowing decks with sand abrasion damage.
5. Emission Control System components necessary to comply with CARB-TIER III and EPA regulations which are manufactured
by third party engine manufacturer.
SECTION 4: EXCEPTIONS AND LIMITATIONS
This warranty shall be inapplicable to defects resulting from the following:
1. Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse
reaction due to incorrect storage or use habits;
2. Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished by
Husqvarna;
3. Alterations or modifications that change the intended use of the product or affects the product’s performance, operation, safety,
or durability, or causes the product to fail to comply with any applicable laws; or:
4. Additional damage to parts or components due to continued use occurring after any of the above.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER.
HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY
EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW.
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THESE PRODUCTS
IS LIMITED IN DURATION TO THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT.
HUSQVARNA RESERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NOTICE,
AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY MANUFACTURED PRODUCTS.
Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long an implied warranty
lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
SECTION 5: CUSTOMER RESPONSIBILITIES
The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written in the maintenance
section of the Owner’s/Operator’s manual. Should an operational problem or failure occur, the product should not be used, but
delivered as is to an authorized Husqvarna retailer for evaluation. Proof of purchase, as explained in section 6, rests solely with
the customer.
SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION
It is the Owner’s and Retailer’s responsibility to make certain that the Warranty Registration Card is properly filled out and mailed
to Husqvarna Forest & Garden Company. This card should be mailed within ten (10) days from the date of purchase in order to
confirm the warranty and to facilitate post-sale service.
Proof of purchase must be presented to the authorized Husqvarna retailer in order to obtain warranty service. This proof must
include date purchased, model number, serial number, and complete name and address of the selling retailer.
To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna retailer
in a timely manner, no later that thirty (30) days from date of the operational problem or failure. The product must be delivered at
the owner’s expense. Downtime, pick-up and delivery charges are not covered by this warranty. An authorized Husqvarna retailer
can be normally located through the “Yellow Pages” of the local telephone directory or by calling 1-800-HUSKY62 for a dealer in
your area.
HUSQVARNA
7349 Statesville Road
Charlotte, NC 28269
10
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
4. Cut down all four corners of the carton and lay the
Read and follow the assembly and adjustment
instructions for your snowthrower. All fasten-
ers are in the parts bag. Do not discard any
parts or material until the unit is assembled.
side panels flat.
5. Cut off the plastic bag that covers the snowthrower.
6. Hold onto the lower handle and pull the snowthrower
off the carton.
WARNING: Before doing any assembly
or maintenance to the snowthrower,
remove the wire from the spark plug.
CAUTION: DO NOT back over cables.
NOTE: In this instruction book, left and right
describe the location of a part from the operator’s
position behind the unit.
7. Remove the packing material from the handle as-
sembly.
HOW TO ASSEMBLE THE HANDLE
NOTE: Torque is measured in foot pounds (metric
Nm). This measurement describes how tight a nut
or bolt must be. The torque is measured with a
torque wrench.
1. Remove the packing material from the upper and
lower handles.
2. (Figure 1) Loosen the knobs (1) on each side of
the handle (2).
PARTS BAG CONTENTS
1 - Electric Start Cord (Not Shown)
1 - Owner’s Manual
1 - Fuel Stabilizer
3. Raise the upper handle (2) to the operating posi-
tion. Hold the upper handle (2) apart to prevent
scratching the lower handle.
1 - Container Oil 5W30
NOTE: Make sure the cables are not caught
between the upper and lower handle.
TOOLS REQUIRED FOR ASSEMBLY
1 − Knife
4. Tighten the knobs.
WARNING: Always wear safety glasses
or eye shields while assembling the
snowthrower.
Figure 3 shows the snowthrower in the operating
position.
References to the right or left hand side of the snow
thrower are from the viewpoint of the operator’s
position behind the unit.
1
HOW TO REMOVE THE SNOWTHROWER
FROM THE CARTON
2
1
1. Locate and remove the container of oil.
2. Locate all parts that are packed separately and
remove from the carton.
Figure 1
3. Remove and discard the packing material from
around the snowthrower.
11
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
ADD FUEL TO THE ENGINE
ADD OIL TO THE ENGINE
This engine is certified to operate on gasoline or
petrol. The emissions control system for this engine is
EM (Engine Modifications).
NOTE: Engine may already contain some
residual oil. Check frequently when filling the
crankcase. DO NOT overfill.
WARNING: Alcohol blended fuels (called
gasohol or those using ethanol or methanol)
can attract moisture which leads to separation and
formation of acids during storage. Acidic gas can
damage the fuel system of an engine while in storage.
The snow thrower was shipped with a container
of 5W30 motor oil. This oil must be added to the
engine before operating.
NOTE: To avoid engine problems, the fuel system must
be emptied before storage for 30 days or longer. Start the
engine and let it run until the fuel lines and carburetor are
empty. Use fresh fuel next season. See the Storage section
in this manual for additional information.
OIl Fill Cap/Dipstick
Fill the fuel tank only with fresh, clean, unleaded regular,
unleaded premium, or reformulated automotive fuel with
DꢀPLQLPXPꢀRIꢀꢉꢋꢀRFWDQHꢃꢀ'2ꢀ127ꢀXVHꢀOHDGHGꢀJDVROLQHꢀ
or petrol. Make sure that the container you pour the fuel
is free from rust or foreign particles. Never use fuel that
may be stale from long periods of storage in the container.
Figure 2
NOTE: Oil level must be at FULL mark.
1. Make sure the unit is level.
1. Stop the engine. Before you remove fuel
cap, let the engine cool at least 2 minutes.
2. Remove the oil fill cap/dipstick and fill
the crankcase to “FULL” line on dipstick.
DO NOT overfill.
2. Remove the fuel cap. Fill the fuel tank to
ꢀꢀꢀꢀꢀꢀꢀDSSUR[LPDWHO\ꢀꢅꢂꢅꢆꢁꢀLQFKHVꢀꢇꢈꢉꢀPPꢊꢀEHORZ
top of neck to allow for fuel expansion. Be
careful not to overfill.
3. Pour the oil slowly into the engine oil fill.
DO NOT overfill. After adding oil, wait one
minute and then recheck the oil level.
3. Replace the fuel cap before starting the engine.
4. Tighten the oil fill cap/dipstick securely each
time you check the oil level.
WARNING: Gasoline and petrol and its vapors
are extremely flammable and explosive. Fire or
explosion can cause severe burns or death.
‡ꢀꢀꢀꢀ7XUQꢀHQJLQHꢀRIIꢀDQGꢀOHWꢀHQJLQHꢀFRROꢀDWꢀOHDVWꢀꢁꢀPLQXWHV
removing the gas cap.
‡ꢀꢀꢀꢀ)LOOꢀIXHOꢀWDQNꢀRXWGRRUVꢀRUꢀLQꢀZHOOꢂYHQWLODWHGꢀDUHDꢃ
‡ꢀꢀꢀꢀ.HHSꢀJDVROLQHꢀDZD\ꢀIURPꢀVSDUNVꢄꢀRSHQꢀIODPHVꢄꢀSLORW
lights, head, and other ignition sources.
NOTE: Synthetic oil can assist with starting in
extreme cold temperatures. Synthetic 5W30 is
acceptable for all temperatures. Do NOT mix oil
with unleaded gasoline.
‡ꢀꢀꢀꢀ,IꢀIXHOꢀVSLOOVꢄꢀZDLWꢀXQWLOꢀLWꢀHYDSRUDWHVꢀEHIRUHꢀVWDUWLQJꢀ
engine.
12
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
BEFORE YOU OPERATE
KNOW YOUR SNOWTHROWER
Before you operate your new snow thrower,
please review the following checklist:
‡ꢀꢀꢀꢀ0DNHꢀVXUHꢀDOOꢀDVVHPEO\ꢀLQVWUXFWLRQVꢀKDYHꢀEHHQ
ꢀꢀꢀꢀꢀFRPSOHWHGꢃ
5HDGꢀWKLVꢀ,QVWUXFWLRQꢀ%RRNꢀDQGꢀVDIHW\ꢀUXOHVꢀEHIRUHꢀ
RSHUDWLQJꢀWKHꢀVQRZꢀWKURZHUꢃꢀ&RPSDUHꢀWKHꢀLOOXVWUDWLRQ
ZLWKꢀ\RXUꢀVQRZꢀWKURZHUꢀWRꢀIDPLOLDUL]Hꢀ\RXUVHOIꢀZLWK
WKHꢀORFDWLRQꢀRIꢀYDULRXVꢀFRQWUROVꢀDQGꢀDGMXVWPHQWVꢃ
‡ꢀꢀꢀꢀ0DNHꢀVXUHꢀWKHꢀGLVFKDUJHꢀFKXWHꢀURWDWHVꢀIUHHO\ꢃ
‡ꢀꢀꢀꢀ0DNHꢀVXUHꢀWKDWꢀQRꢀORRVHꢀSDUWVꢀUHPDLQꢀLQꢀWKHꢀ
ꢀꢀꢀꢀꢀFDUWRQꢃ
As you learn how to properly use the snow
thrower, pay extra attention to the following
LPSRUWDQWꢀLWHPVꢌ
‡ꢀꢀꢀꢀ0DNHꢀVXUHꢀWKHꢀHQJLQHꢀRLOꢀLVꢀDWꢀWKHꢀSURSHU
ꢀꢀꢀꢀꢀOHYHOꢃꢀ)RUꢀWKHꢀW\SHꢀHQJLQHꢀRLOꢀWRꢀXVHꢄꢀVHHꢀWKH
ꢀꢀꢀꢀꢀ(QJLQHꢀ0DQXIDFWXUHU¶VꢀPDQXDOꢃ
‡ꢀꢀꢀꢀ0DNHꢀVXUHꢀWKHꢀIXHOꢀWDQNꢀLVꢀILOOHGꢀZLWKꢀFOHDQꢄꢀ
ꢀꢀꢀꢀꢀIUHVKꢄꢀXQOHDGHGꢀJDVROLQHꢀRUꢀSHWUROꢀZLWKꢀDꢀ
ꢀꢀꢀꢀꢀPLQLPXPꢀRIꢀꢉꢋꢀRFWDQHꢃ
ꢃ
‡ ꢀ%HFRPHꢀIDPLODUꢀZLWKꢀWKHꢀORFDWLRQꢀRIꢀDOO
ꢀꢀꢀꢀꢀFRQWUROVꢀDQGꢀXQGHUVWDQGꢀWKHLUꢀIXQFWLRQꢃ
‡ꢀꢀꢀꢀ%HIRUHꢀVWDUWLQJꢀWKHꢀHQJLQHꢄꢀPDNHꢀVXUHꢀDOO
ꢀꢀꢀꢀꢀFRQWUROVꢀRSHUDWHꢀFRUUHFWO\ꢃ
13
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
4
1
2
12
6
10
7
3
8
5
9
11
Figure 3
Ignition Key (6) - If equipped, insert and turn to the
Control and Equipment Features (Figure 3)
ON position to start the engine.
Crank Assembly (1) - Changes the direction of
the discharge chute.
Primer Button (7) - Injects fuel directly into the
carburetor for fast starts in cold weather.
Chute Deflector (2) - Changes the distance the
snow is thrown.
Engine Start Button (8) - On electric start models,
used to start the engine.
Discharge Chute (3) - Changes the direction the
snow is thrown.
Switch Box (9) - On electric start models, used to
attach electrical power cord.
Auger Drive Lever (4) - Starts and stops the auger
which propels the snow thrower.
Recoil Starter Handle (10) - Used to manually
start the engine.
Auger Blades (5) - Cuts through the snow.
Choke Control (11) - Used to start a cold engine.
Engine Features (Figure 3)
Spark Plug Access Panel (12) - Remove to access
the spark plug.
Stop Switch (6) - If equipped, move to the ON position
to start the engine.
14
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
HOW TO CONTROL DISCHARGE
OF SNOW
WARNING: The operation of any snow
thrower can result in foreign objects
being thrown into the eyes, which can result
in severe eye damage. Always wear safety
glasses or eye shields while operating the
snow thrower. We recommend standard
safety glasses or use a wide vision safety
mask over your glasses.
WARNING: Never direct the dis-
charge of snow toward bystanders.
WARNING: Always stop the engine
before unclogging the discharge chute
or the auger housing and before leaving the
snow thrower.
HOW TO STOP DISCHARGING SNOW
1. (Figure 3) To stop discharging snow, release
1. (Figure 3) Turn the crank assembly (1) to
the auger drive lever (4).
change the discharge direction of the snow.
2. To stop the engine, turn the ignition key (5)
to the OFF position.
2. (Figure 4) Loosen the wing knob (1) on the
chute deflector (2).
HOW TO MOVE FORWARD
2
2
1. (Figure 3) Hold the auger drive lever (4)
against the handle (10). The auger will begin
rotating.
2. To go forward, raise the handle (10) to allow
the rubber auger blades (5) to contact the
ground. Maintain a firm hold on the handle
(10) as the snow thrower starts to move for-
ward. Guide the snowthrower by moving the
handle (10) either left or right. Do not attempt
to push the snowthrower.
1
1
Figure 4
3. Move the chute deflector (2) up for more distance or
down for less distance.
3. To stop, release the auger drive lever (4).
4. Tighten the wing knob (1).
NOTE: If the auger continues to rotate, see
“How To Adjust The Auger Control Cable” in
the Maintenance section.
HOW TO THROW SNOW
1. (Figure 3) Engage the auger drive lever (4).
2. To stop throwing snow, release the
auger drive lever.
15
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
BEFORE STARTING THE ENGINE
HOW TO START A COLD ENGINE
1. Before you service or start the engine,
familiarize yourself with the snow thrower. Be
sure you understand the function and location
of all controls.
1. Fill the fuel tank with fresh, clean fuel. See “Add
Fuel To The Engine” in the Assembly section.
2. Move the choke control to FULL position.
2. Make sure that all fasteners are tight.
3. (Figure 3) Make sure the auger drive lever (4) is
in the disengaged (released) position.
3. Make sure the fuel tank is filled with fresh,
clean fuel.
4. Insert the ignition key (6) and turn to the ON
position.
4. Before starting the engine, make sure all
controls operate correctly.
5. Move the choke control (11) to the full choke
position.
HOW TO STOP THE ENGINE
6. (Electric Start) Connect the power cord to the
switch box (9) located on the engine.
To stop the engine, turn the ignition key to
the OFF position. Keep the ignition key in a
safe place. The engine will not start without
the ignition key.
7. (Electric Start) Plug the other end of the power
cord into a three-hole, grounded 120 volt AC
receptacle. (See the WARNING in this section.)
8. Push the primer button (7) two times. Every time
you push the primer button (7), wait two seconds.
HOW TO START THE ENGINE
NOTE: An electric starter kit can be added
to recoil start engines. Electric starter kits are
available from your nearest authorized service
center.
9. (Electric Start) Push on the electric start button
(8) until the engine starts. Do not crank for more
than 10 seconds at a time.The electric starter is
thermally protected. If the electric starter over-
heats, it will automatically stop and can be re-
started when it has cooled to a safe temperature.
A wait of about 5 to 10 minutes is required to
allow the electric starter to cool.
WARNING: The starter is equipped with
a three-wire power cord and plug and is
designed to operate on 120 AC household
current. Carefully follow all instructions in the
“How To Start The Engine” section. To connect
a 120 volt AC power cord, always connect the
power cord to the switch box first. Then, plug
the other end into the three-hole grounded
receptacle. When disconnecting the power
cord, always unplug the end from the three-
hole grounded receptacle first.
10. (Recoil Start) Rapidly pull the recoil starter
handle (10). Do not allow the recoil starter han-
dle (10) to snap back. Slowly return the recoil
starter handle (10).
11. If the engine does not start in 5 or 6 tries, see the
“Troubleshooting Chart” instructions.
12. (Electric Start) When the engine starts, release
the electric start button (8) and move the choke
control (14) to 1/2 choke position. When the en-
gine runs smoothly, move the choke control (11)
to the OFF position.
16
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
1. With the engine running, quickly pull the re-
13. (Electric Start) First disconnect the power
cord from the three-hole receptacle. Then,
disconnect the power cord from the switch
box (9).
coil starter handle (10) three or four times with
a continuous full arm stroke. This will produce a
loud clattering sound that is not harmful to the
engine or starter.
NOTE: In temperatures below 0° F, allow the
engine to warm up for several minutes before
blowing snow.
2. Stop the engine. Wipe all snow and moisture
from the carburetor cover, control levers, and
cables. Also move the choke control (11) and
recoil starter handle (10) several times.
WARNING: Never run the engine indoors
or in enclosed, poorly ventilated areas.
Engine exhaust contains carbon monoxide, an
odorless and colorless deadly gas. Keep hands,
feet, hair, and loose clothing away from any
moving parts located on the engine or the snow
thrower. The temperature of muffler and nearby
areas may exceed 150° F. Avoid these areas.
HOW CLEAR A CLOGGED DISCHARGE CHUTE
WARNING: Hand contact with the rotating
impeller inside the discharge chute is the
most common cause of injury associated with
snow blowing. Never use your hand to clean out
the discharge chute.
HOW TO START A WARM ENGINE
To Clear The Chute:
‡ꢀꢀꢀꢀ6KXWꢀRIIꢀWKHꢀHQJLQH
(Figure 3) If an engine has been running and is
still warm, leave the choke control (11) in the OFF
position and do not push the primer button (7). If
the engine fails to start, follow the instructions “How
To Start A Cold Engine.”
‡ꢀꢀꢀꢀ:DLWꢀꢅꢍꢀVHFRQGVꢀWRꢀEHꢀVXUHꢀWKDWꢀWKHꢀLPSHOOHUꢀEODGHV
have stop rotating.
‡ꢀꢀꢀꢀ$OZD\VꢀXVHꢀDꢀFOHDQꢂRXWꢀWRROꢄꢀQRWꢀ\RXUꢀKDQGVꢃ
How To Use A Clean-Out Tool:
‡ꢀꢀꢀꢀ5HOHDVHꢀWKHꢀDXJHUꢀGULYHꢀOHYHUꢃ
‡ꢀꢀꢀꢀ3XOOꢀRXWꢀRUꢀUHPRYHꢀWKHꢀVDIHW\ꢆLJQLWLRQꢀNH\ꢃ
‡ꢀꢀꢀꢀ'LVFRQQHFWꢀWKHꢀVSDUNꢀSOXJꢀZLUHꢃ
‡ꢀꢀꢀꢀ'RꢀQRWꢀSODFHꢀ\RXUꢀKDQGVꢀLQꢀWKHꢀDXJHUꢀRUꢀGLVꢂ
charge chute. Use a clean-out tool to remove
snow or debris.
NOTE: Do not use the primer button (7) to start
a warm engine.
HOW TO START A WARM ENGINE WITH A
FROZEN STARTER
If the electric starter is frozen and will not turn
the engine, follow the instructions below.
SNOW THROWING TIPS
1. (Figure 3) Pull out the recoil starter handle (10)
1. This snow thrower will propel itself forward when
the handle is raised enough to cause the auger
blades to contact the ground. The auger should
stop when auger control bar is released. If it does
not stop, see “How To Adjust The Auger Control
Cable” in the Maintenance section.
as far as possible.
2. Quickly release the recoil starter handle (10)
to snap back against the recoil starter.
If the engine still fails to start, repeat the two pre-
vious steps until the engine starts. Then, continue
with the directions “How To Start A Cold Engine.”
2. Most efficient snow throwing is accomplished when
the snow if removed immediately after it falls.
To help prevent the possible freeze-up of the
recoil starter and of the engine controls, proceed
as follows after each snow removal job.
17
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Dry and Average Snow
3. For complete snow removal, slightly overlap
leach previous path.
1. Snow up to eight inches deep can be removed
rapidly and easily by walking at a moderate
rate. For snow drifts of a greater depth, slow
your pace to allow the discharge chute to dis-
pose of the snow as rapidly as the auger receives
the snow.
4. When possible, discharge the snow down wind.
5. The distance the snow will be discharged can
be adjusted by moving the discharge chute
deflector. Raise the deflector for more distance
or lower the deflector for less distance.
2. Plan to have the snow discharged in the direction
the wind is blowing.
6. In windy conditions, lower the chute deflector
to direct the discharged snow close to the
ground where it is less likely to blow into un-
wanted areas.
Wet Packed Snow
Move slowly into wet, packed snow. If the wet,
packed snow causes the auger to slow down or
the discharge chute begins to clog, back off and
begin a series of short back and forth jabs into
the snow. These short back and forth jabs, four
to six inches, will “belch” the snow from the chute.
7. For safety and to prevent damage to the snow
thrower, keep the area to be cleared free of
stones, toys, and other foreign objects.
8. Do not use the auger propelling feature when
clearing gravel or crushed rock driveways. Move
the handle down to slightly raise the auger.
Snow Banks And Drifts
9. The forward speed of the snowthrower is depen-
dent on the depth and weight of the snow. Exper-
ience will establish the most effective method of
using the snow thrower under different conditions.
In snow of greater depth than the unit, use the
same “jabbing” technique described above. Turn
the discharge chute away from the snow bank.
More time will be required to remove snow of this
type than level snow.
10. After each snow throwing job, allow the engine to
run for a few minutes. The snow and accumulated
ice will melt off the engine.
11. Clean the snowthrower after each use.
12. Remove ice, snow, and debris from the entire
snow thrower. Flush with water to remove all
salt or other chemicals. Wipe snow thrower dry.
18
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CUSTOMER RESPONSIBILITIES
SERVICE RECORDS
Fill in dates as you
complete regular
service.
Before
Each
Use
First
2
Every
5
Every
10
Hours
Every
25
Hours
Each
Before
Season Storage
Hours Hours
SERVICE DATES
Check And Tighten All Screws and Nuts
√
√
Check Spark Plug
Check Drive Belt
Check Fuel
√
√
√
√
Drain Fuel
√
√
Lubricate Chute Control Flange
Check Adjustment of Auger Control Cable
Auger Drive Belt
√
√
NOTE: Use the following maintenance section
ENGINE POWER RATING INFORMATION
to keep your unit in good operating condition.
The gross power rating for individual gas engine models
is labeled in accordance with SAE (Society of Automotive
Engineers) code J1940 (Small Engine Power & Torque Rating
Procedure), and rating performance has been obtained and
corrected in accordance with SAE J1995 (Revision 2002-05).
Torque values are derived at 3060 RPM; horsepower values
are derived at 3600 RPM. Actual gross engine power will be
lower and is affected by, among other things, ambient oper-
ating conditions and engine-to-engine variability. Given
both the wide array of products on which engines are
placed and the variety of environmental issues applicable
to operating the equipment, the gas engine will not develop
the rated gross power when used in a given piece of power
equipment (actual "on-site" or net power). This difference
to due to a variety of factors including, but not limited to,
accessories (air cleaner, exhaust, charging, cooling, carbur-
etor, fuel pump, etc.), application limitations, ambient oper-
ating conditions (temperature, humidity, altitude), and
engine-to-engine variability. Due to manufacturing and
capacity limitations, Briggs & Stratton may substitute
an engine of higher rated power for this Series engine.
All the maintenance for the engine is in the engine
manufacturer’s instructions. Before you start the
engine, read this book.
WARNING: Before you make an inspec-
tion, adjustment (except carburetor), or
repair, disconnect the wire from the spark plug.
EMISSIONS CONTROL
Maintenance, replacement, or repair of the emissions
control devices and systems may be performed by
any non-road engine repair establishment or indiv-
However, to obtain a “no charge”emissions control
service, the work must be performed by a factory author-
ized dealer. See the Emissions Warranty.
GENERAL RECOMMENDATIONS
The warranty on this snowthrower does not cover items
that have been subjected to operator abuse or negligence.
To receive full value from the warranty, the operator must
maintain the snow thrower as instructed in this manual.
19
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
AFTER EACH USE
ꢐꢃꢀꢀꢀꢀ&DUHIXOO\ꢀSXOOꢀWKHꢀUHDUꢀRIꢀWKHꢀWRSꢀFRYHUꢀꢇꢎꢊꢀXSꢀDQG
ꢀꢀꢀꢀꢀꢀꢀRYHUꢀWKHꢀJDVꢀWDQNꢃ
‡ꢀꢀꢀꢀ&KHFNꢀIRUꢀDQ\ꢀORRVHꢀRUꢀGDPDJHGꢀSDUWVꢃ
‡ꢀꢀꢀꢀ7LJKWHQꢀDQ\ꢀORRVHꢀIDVWHQHUVꢃ
‡ꢀꢀꢀꢀ&KHFNꢀDQGꢀPDLQWDLQꢀWKHꢀDXJHUꢃ
‡ꢀꢀꢀꢀ&KHFNꢀFRQWUROVꢀWRꢀPDNHꢀVXUHꢀWKH\ꢀDUH
ꢀꢀꢀꢀꢀIXQFWLRQLQJꢀSURSHUO\ꢃ
‡ꢀꢀꢀꢀ,IꢀDQ\ꢀSDUWVꢀDUHꢀZRUQꢀRUꢀGDPDJHGꢄꢀUHSODFH
ꢀꢀꢀꢀꢀLPPHGLDWHO\ꢃ
ꢉꢃꢀꢀꢀꢀ7RꢀLQVWDOOꢀWKHꢀWRSꢀFRYHUꢀꢇꢎꢊꢄꢀUHYHUVHꢀWKHꢀDERYH
ꢀꢀꢀꢀꢀꢀꢀVWHSVꢃ
LUBRICATION BEFORE STORAGE
‡ꢀꢀꢀꢀ&KHFNꢀDOOꢀVDIHW\ꢀDQGꢀLQVWUXFWLRQꢀGHFDOV
ꢀꢀꢀꢀꢀDQGꢀODEHOVꢃꢀ5HSODFHꢀDQ\ꢀGHFDOVꢀRUꢀODEHOV
ꢀꢀꢀꢀꢀWKDWꢀDUHꢀPLVVLQJꢀRUꢀFDQQRWꢀEHꢀFOHDUO\ꢀUHDGꢃ
(Figure 5) Lubricate the chute control flange (7). Apply
a clinging type of grease such as Lubriplate.
3
6
HOW TO REMOVE THE TOP COVER
ꢅꢃꢀꢀꢀꢀ(Figure 5) 5HPRYHꢀWKHꢀGLVFKDUJHꢀFKXWHꢀꢇꢅꢊꢃ
ꢁꢃꢀꢀꢀꢀ5HPRYHꢀWKHꢀIXHOꢀFDSꢃ
2
ꢈꢃꢀꢀꢀꢀ5HPRYHꢀWKHꢀWZRꢀQXWVꢀDQGꢀEROWVꢀꢇꢁꢊꢀIURPꢀWKH
ꢀꢀꢀꢀꢀꢀꢀIURQWꢀRIꢀWKHꢀWRSꢀFRYHUꢀꢇꢈꢊꢃ
ꢎꢃꢀꢀꢀꢀ5HPRYHꢀWKHꢀWZRꢀEROWVꢀꢇꢎꢊꢀIURPꢀWKHꢀOHIWꢀDQGꢀULJKW
ꢀꢀꢀꢀꢀꢀꢀRIꢀWKHꢀWRSꢀFRYHUꢀꢇꢈꢊꢃ
4
5
1
ꢋꢃꢀꢀꢀꢀ5HPRYHꢀWKHꢀHLJKWꢀVFUHZVꢀꢇꢋꢊꢀRQꢀWKHꢀOHIWꢀDQG
ꢀꢀꢀꢀꢀꢀꢀULJKWꢀVLGHꢀRIꢀWKHꢀWRSꢀFRYHUꢃ
7
Figure 5
ꢏꢃꢀꢀꢀꢀ5HPRYHꢀWKHꢀWKUHHꢀVFUHZVꢀꢇꢏꢊꢀIURPꢀWKHꢀWRSꢀ
ꢀꢀꢀꢀꢀꢀꢀSRUWLRQꢀRIꢀWKHꢀFRQWUROꢀSDQHOꢃ
20
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
HOW TO ADJUST THE AUGER CONTROL
CABLE
The auger control is adjusted at the factory. During
normal use, the auger control cable can become
stretched and the auger drive lever will not pro-
perly engage or disengage the auger.
7. (Figure 6) Install the “Z”hook (1) to the
auger drive lever (2).
8. To check the adjustment, start the snowthrower.
Make sure the auger does not rotate when the
auger drive is released.
1. (Figure 6) Remove the “Z”hook (1) from the
auger drive lever (2).
3
1
2
2
4
1
2
Figure 7
Figure 6
HOW TO REMOVE THE BELT COVER
2. (Figure 7)
1. (Figure 8) If equipped, remove the heat shield (1)
cable adjustment bracket (2).
from the rear of the belt cover (2).
3. Push the bottom of the auger control cable (3)
through the cable adjustment bracket (2) until
the “Z”hook (6) can be removed.
2. Remove the four bolts and nuts (3) holding
the belt cover (2) to the auger housing.
3. Remove the one screw (4) holding the belt
cover (2) to the bottom cover (5).
4. Remove the “Z” hook (4) from the cable adjust-
ment bracket (2). Move the “Z” hook (4) down to
the next adjustment hole.
4. To remove, hold the bottom portion of the
belt cover (2) and pull down and out.
5. Pull the auger control cable (3) up through the
cable adjustment bracket (2).
5. To install the belt cover (2), reverse the above
steps.
6. Put the cable boot (1) over the cable adjustment
bracket (2).
21
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
3. Move the belt guide (4) away from the drive
belt (1).
5
1
4. To reduce pressure on the drive belt (1), move
the idler pulley (2) away from the drive belt (1).
Remove the drive belt (1) from between the
brake pad (3) and the roller (5).
6
2
5. Remove the old drive belt (1).
3
6
6. To install the new drive belt (1), reverse the
above steps.
3
4
3
3
7. Make sure the drive belt (1) is seated properly
on the pulleys.
Figure 8
8. (Figure 10) Set the belt guide (1) to 3/32”
HOW TO REPLACE THE DRIVE BELT
The drive belt is of special construction and must be
clearance.
replaced with original factory replacement belt avail-
able from your nearest authorized service center.
NOTE: When the auger control lever is en-
gaged, the belt guide (1) must be 3/32” (2 mm)
from the drive belt (2).
1. Remove the belt cover. See “How To Remove The
Belt Cover.”
9. Install the belt cover. See “How To Remove
The Belt Cover.”
2. (Figure 9) Remove the drive belt (1) from the idler
pulley (2).
2
3
4
2
5
1
3/32”
Figure 10
1
Figure 9
22
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
HOW TO REPLACE THE AUGER
HOW TO ADJUST THE BRAKE PAD
1. Remove the belt cover. See “How To Remove
The Belt Cover.”
IMPORTANT: An adjustment is only necessary if
the brake pad has become loose or has been re-
moved. to adjust, proceed as follows:
2. Remove the drive belt. See “How To Replace
The Drive Belt.”
1. Remove the top cover. See “How To Remove
The Top Cover.”
3
2. Remove the belt cover. See “How To Remove
The Belt Cover.”
3. Tie the auger drive lever to the handle. This will
engage the drive system.
6
4. (Figure 12) Loosen the screw and nut that
secure the brake pad arm (1).
5. Set the clearance between the brake pad (2)
and the drive belt (3) to 1/8 inch (3 mm).
4
2
5
6. Tighten the screw and nut that secure the brake
pad arm (1).
1
Figure 11
7. Connect the wire to the spark plug.
3. (Figure 11) Remove the auger pulley (1) from
the auger shaft (threads are left hand; turn clock-
wise to remove).
1
3
2
4. To keep the auger (2) from rotating, set a
2” x 4” piece of wood (3) on the center pad-
dle (4) to secure the auger (2).
5. Remove the fasteners from the bearing as-
sembly (4). Remove the bearing assembly
(4) from the auger housing (5).
6. Slide the auger (2) out the bearing assem-
bly on the right side of the snow thrower.
Figure 12
7. Tip the auger (2) enough to allow the auger
(2) to slide out of the auger housing (6).
8. To install auger (2), reverse the above steps.
23
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
HOW TO REPLACE THE SPARK PLUG
6. Check the spark plug. If the spark plug is
cracked, fouled, or dirty, it must be replaced.
NOTE: This spark plug ignition system meets
all requirements of the Canadian Intereference-
Causing Equipment Regulations (ICES-002).
7. (Figure 14) Set the gap between the elec-
trodes of the new spark plug at .030 inch.
Next, install the spark plug in the cylinder
head and firmly tighten. Recommended
torque is 18 to 20 ft-lbs.
NOTE: This engine complies with all current
Australian and New Zealand limitations electro-
magnetic interconference.
The spark plug is housed in the engine compart-
ment under the top cover and cannot be seen
under normal conditions.
1. (Figure 13) Open the spark plug access
door (1) on the control panel.
2. The spark plug and wire are now visible.
3. Remove the spark plug wire.
Figure 14
4. Clean the area around the spark plug base
to prevent dirt from entering the engine when
the spark plug is removed.
HOW TO PREPARE THE SNOWTHROWER
FOR STORAGE
WARNING: Before you make an inspec-
tion, adjustment (except carburetor), or
5. Remove the spark plug.
repair, disconnect the wire from the spark plug.
1
1. Drain the fuel tank.
2. Let the engine run until it is out of gasoline or
petrol.
3. Remove the spark plug from the cylinder.
a. Pour one ounce of oil into the cylinder.
b. Slow pull the recoil-start grip so that the oil
will protect the cylinder.
c. Install a new spark plug in the cylinder.
4. Thorougly clean the snow thrower.
Figure 13
5. Lubricate all lubrication points. See the Mainten-
ance section.
24
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
HOW TO ORDER REPLACEMENT PARTS
6. Be sure that all nuts, bolts, and screws are
securely fastened. Inspect all visible moving
parts for damage, breakage, and wear. Replace
if necessary.
Use only manufacturer’s authorized or approved
replacement parts. Do not use attachments
or accessories not specifically recommended for
this unit. In order to obtain proper replacement you
must supply the model number (see nameplate).
7. Cover the bare metal parts of the blower
housing and auger with spray rust pre-
ventative lubricant.
Warranty service is available only through Authorized
Service Dealers.
8. Put the unit in a building that has good
ventilation.
9. If the machine must be stored outdoors,
block up the snow thrower to be sure the
entire machine is off the ground.
10. Cover the snow thrower with a suitable
protective cover that does not retain
moisture. Do not use plastic.
25
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING CHART
Trouble
Cause
Correction
Difficulty starting
Defective spark plug.
Replace spark plug.
Water or dirt in fuel system.
Use carburetor bowl drain to flush and
refill with fresh fuel.
Engine runs erratic
Engine stalls
Blocked fuel line, empty gas tank,
or stale gasoline/petrol.
Clean fuel line; check fuel supply; add
fresh fuel.
Unit running on CHOKE.
Set choke lever to RUN position.
Engine runs erratic; loss of
power
Water or dirt in fuel system.
Use carburetor bowl drain to flush and
refill with fresh fuel.
Excessive vibration
Loose parts; damaged impeller.
Stop engine immediately and disconnect
spark plug wire. Tighten all bolts and
make all necessary repairs. If vibration
continues, have the unit serviced by a
competent repairman.
Unit fails to propel itself
Drive belt loose or damaged.
Replace drive belt.
Auger drive belt loose or damaged.
Adjust auger drive belt; replaced if dam-
aged.
Unit fails to discharge snow
Auger control cable not adjusted
correctly.
Adjust auger control cable.
Discharge chute clogged.
Stop engine immediately and disconnect
spark plug. Clean discharge chute and
inside of auger housing.
Foreign object lodged in auger.
Stop engine immediately and disconnect
spark plug wire. Remove object from
auger.
26
1741506
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine And Frame Assembly
0003
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
4
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine And Frame Assembly
REF NO PART NO.
DESCRIPTION
1
-----
ENGINE (09A413-0202-E1 FOR MODEL NO. 6210540X37NA-ELECTRIC STARTER)
ENGINE (09A412-0267-E1 FOR MODEL NO. 6210530X37NA-RECOIL STARTER)
NUT, 5/16-18
1
-----
2
601 50 51 29
601 40 00 79
601 50 51 30
601 50 51 31
601 50 51 32
601 40 00 80
601 50 51 33
601 50 51 34
601 00 14 19
601 00 13 48
601 50 51 35
601 40 00 85
601 50 51 36
601 00 00 73
601 50 51 37
601 50 51 38
601 00 17 79
601 50 51 39
601 50 51 38
601 40 00 65
601 50 51 41
601 50 51 42
601 50 51 43
601 50 51 44
601 00 13 31
601 00 16 94
601 00 13 37
601 40 00 75
601 50 51 45
601 00 13 33
601 50 51 46
601 00 13 34
601 00 13 30
601 00 13 96
601 00 20 81
601 00 13 28
601 00 13 29
601 50 51 50
601 50 51 51
601 00 00 26
601 00 05 33
601 50 51 64
601 40 00 86
3
WASHER, SPLIT LOCK .31 X .58 X .08
TANK, FUEL 1.5 QT
4
5
RING, FOAM FUEL TANK
FUEL CAP
6
7
WASHER, FLAT .281 X .63. X .065
SCREW, 1/4-20 X 0.75
8
9
BRACKET, FUEL TANK
NUT, 8-32 HEX KEPS
10
11
12
13
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
SCREW, 1/4-20 X 2.00
NUT, 1/4-20 HEX
NUT, 5/16-18 HEX CONTROL LOCK
CRADLE, WELDMENT
BOLT, 5/16-18 X 0.75
BOLT, HEX .31-18 X 1.62
HOSE, FUEL
CLAMP, HOSE
FILTER- FUEL
HOSE, FUEL
CLAMP, SCREW TYPE
PLATE, SUPPORT
FRAME, RIGHT HAND
CHANNEL, FRAME SUPPORT
FRAME, LEFT HAND
ARM, IDLER BLACK
BRAKE PAD
ROD, CLUTCH LINKAGE
NUT, 3/8-16 JAM CONTROL LOCK
WIRE, BRAKE
PULLEY, IDLER
PINCH ROLLER
SCREW, 3/8-16 X 1.50
SPRING, EXTENSION .38 O.D. X .039 X 2.50
SPRING, EXTENSION .75 O.D. X .069 X 2.00
BELT
ARM, IDLER PIVOT
BOLT, SHOULDER .500 X .177
WASHER, FLAT .378 X .75 X .080
PULLEY, ENGINE
PIN, COTTER
WASHER, FLAT
GUIDE, BELT
45
NUT, 1/4-20 HEX CONTROL LOCK
Footnotes
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
5
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine And Frame Assembly
0003
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
6
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine And Frame Assembly
REF NO PART NO.
DESCRIPTION
46
47
48
49
50
51
52
53
601 40 00 81
601 00 10 06
601 40 00 73
601 00 14 18
601 50 51 61
601 50 51 62
601 50 51 63
601 00 14 45
WASHER, FLAT .349 X .69 X .066
SCREW 5/16-18 X 0.63 WAHHC
SCREW, 1/4-20 X 0.63
SCREW, 8-32 X 3.00
SPACER, DRIVE PULLEY
BOLT, ENGINE PULLEY, 1/4-28 X 1.28
BOLT, 5/16-18 X 0.865
SCREW, .25-20 X .062 WASHER HEX HEAD TAPTITE
Footnotes
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
7
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Auger And Control Assembly
0005
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
8
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Auger And Control Assembly
REF NO PART NO.
DESCRIPTION
1
601 50 51 47
601 40 00 02
601 50 51 48
601 50 51 49
601 00 21 53
601 50 51 52
601 40 00 80
601 50 51 53
601 50 51 54
601 50 51 33
601 50 51 56
601 40 00 73
601 50 51 57
601 50 51 58
601 40 00 74
601 00 13 81
601 40 00 86
601 00 20 87
601 00 20 95
601 50 51 59
601 50 51 60
601 40 00 76
601 00 01 11
601 40 00 44
601 50 51 89
601 00 01 02
601 00 13 58
601 50 51 65
601 50 51 66
601 40 00 70
601 50 51 40
601 50 51 68
601 50 51 69
601 00 13 78
COVER, TOP
2
SCREW, #10-24 X 0.50
NUT, 1/4-10 SPEED J-TYPE
SCREW, 1/4-14 X 0.75
BEARING, FLANGE
3
4
5
6
SCREW, 1/4-20 X 1.00
WASHER, FLAT, .281 X .63 X .065
NUT, #10-24 HEX CONTROL LOCK
NUT, 1/4-20 HEX CONTROL LOCK
SCREW, 1/4-20 X 0.75
AUGER HOUSING ASSEMBLY
SCREW, 1/4-20 X 0.63
AUGER ASSEMBLY, COMPLETE
BLADE, SCRAPER
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
PLATE & BEARING ASSY
PLATE, RETAINER BEARING
NUT, 1/4-20 HEX CONTROL LOCK
SPACER, SLEEVE
PULLEY
COVER, BELT
COVER, BOTTOM
KEY SET
NUT, 5/8-32
WASHER, .640 X 1.1 X .05
PRIMER, CARBURETOR
NUT, 1/-20 HEX KEPS
SWITCH, IGNITION 45 DEGREE
HOSE, PRIMER 9.5"
PANEL, CONTROL
GROMMET & WASHER, ROPE
GRIP, STARTER ROPE
PANEL, ACCESS
SCREW, 1/4-20 X 1.25
RIVET, OFFSET, .25 X .61
Footnotes
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
9
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Discharge Chute
0007
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
10
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Discharge Chute
REF NO PART NO.
DESCRIPTION
580
581
582
583
590
591
592
600
601
602
603
604
605
606
608
601 50 51 87
601 50 51 88
601 00 13 86
601 50 51 90
601 50 51 91
601 50 51 33
601 50 51 54
601 50 51 94
601 00 13 89
601 00 13 90
601 40 00 81
601 40 00 69
601 50 51 29
601 00 20 38
601 40 00 85
CHUTE RING
SCREW, #10 X .50
GUIDE, CHUTE
DONUT, FOAM 21 PLAST A
CHUTE, DEFLECTOR LOWER
SCREW 1/4-20 X .75
NUT, 1/4-20, HEX CONTROL LOCK
CHUTE DELFECTOR, UPPER
WIRE FORM, HINGE 5.75
BOLT, 5/16-18 X 1.25 CARRIAGE
WASHER, FLAT .349 X .69 X .066
KNOB, WING
NUT, 5/16-18
SCREW, 5/16-18 X .75
NUT, 5/16-18, HEX CONTROL LOCK
Footnotes
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
11
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Handle Assembly
0011
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
12
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Handle Assembly
REF NO PART NO.
DESCRIPTION
1
601 50 51 96
601 50 51 97
601 50 51 29
601 40 00 69
601 00 24 13
601 00 21 50
601 50 51 99
601 50 51 69
601 40 00 80
601 40 00 86
601 00 13 95
601 00 13 92
601 00 13 93
601 00 13 94
601 00 13 96
HANDLE, UPPER
2
BAIL, CONTROL
3
NUT, 5/16-18 HEX
4
KNOB, WING
5
WASHER, FORM .344 I.D.
BOLT, 5/16-18 X 2.00
6
7
HANDLE, LOWER
8
SCREW, 1/4-20 X 1.25
WASHER, FLAT .281 X .63 X .065
NUT, .25-20 HEX CONTROL LOCK
BOOT, CLUTCH SPRING
CABLE, UPPER CONTROL
BRACKET, CABLE ADJUST
CABLE, LOWER CONTROL
SPRING, EXTENSION .75 O.D. X .069 X 2.00
9
10
11
12
13
14
15
Footnotes
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
13
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Chute Rod Assembly
0009
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
14
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Chute Rod Assembly
REF NO PART NO.
DESCRIPTION
850
851
852
853
854
855
856
857
858
859
860
861
870
871
872
873
874
601 50 51 80
601 40 00 82
601 50 51 81
601 00 14 04
601 50 51 82
601 40 00 82
601 00 14 05
601 00 18 17
601 50 51 83
601 40 00 81
601 40 00 79
601 50 51 35
601 50 51 85
601 00 14 11
601 40 00 81
601 40 00 79
601 50 51 29
ROD, CHUTE
WASHER, FLAT .406 X .81 X .066
PIN, COTTER
WASHER, CURVED SPRING
ASSY, CHUTE CRANK BRACKET
WASHER, FLAT .406 X.81 X .066
KNOB, SLEEVE
NUT, PUSH
BOLT, 1/4-20 X .63 CARRIAGE
WASHER, FLAT .349 X .69 X .065
WASHER, SPLIT LOCK .31 X .58 X .08
NUT, 1/4-20 HEX
BRKT, CHUTE ROTATE
BOLT, 5/16-18 X .75 CARRIAGE
WASHER, FLAT .349 X .69 X .065
WASHER, SPLIT LOCK .31 X .58 X .08
NUT, 5/16-18 HEX
Footnotes
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
15
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Decals
0015
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
16
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Decals
REF NO PART NO.
DESCRIPTION
1
2
2
3
3
4
5
5
6
7
8
9
-----
* DECAL, EPA, MASS
601 50 51 75
601 50 52 01
601 50 51 55
601 50 52 03
601 40 00 11
601 40 00 16
601 40 00 15
601 40 00 77
601 50 51 79
601 40 00 67
601 00 23 29
DECAL, ELECTRIC START, COVER UP (Used on Model 6210530x37NA 5021R Only)
DECAL, ELECTRIC START (Used on Model 6210540x37NA 5021E Only)
DECAL, DASH PANEL (Used on Model 6210530x37NA 5021R Only)
DECAL, DASH PANEL (Used on Model 6210540x37NA 5021E Only)
DECAL, HUSQVARNA
DECAL, HUSQVARNA 5021R (Used on Model 6210530x37NA 5021R Only)
DECAL, HUSQVARNA 5021E (Used on Model 6210540x37NA 5021E Only)
DECAL, WARNING HOT MUFFLER
DECAL, AUGER CONTROL
DECAL, DANGER CHUTE
DECAL, DANGER AUGER, FOOT
Footnotes
Note * Not a serviceable part.
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
17
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Wheels
0013
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
18
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Wheels
REF NO PART NO.
DESCRIPTION
650
651
660
661
662
601 50 51 70
601 50 51 71
601 50 51 72
601 50 51 71
601 40 00 72
AXLE, 20.53 WHEEL 20/21
WASHER, FLAT .391 X 1.00 X .125
TIRE & RIM 7 X 1.50
WASHER, FLAT .391 X 1.00 X .125
RING, RETAINER E
Footnotes
The above parts group applies to the following Mfg. Nos.:
6210530x37NA 5021R
6210540x37NA 5021E
Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
19
TP 400-4686-02-ST-Q
Download from Www.Somanuals.com. All Manuals Search And Download.
|