14" SLIDING TABLE SAW
MODEL G0451
INSTRUCTION MANUAL
COPYRIGHT © APRIL, 2005 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#EW6937 PRINTED IN USA. REVISED SEPTEMBER, 2005.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
INTRODUCTION............................................................................................................................... 3
Foreword .................................................................................................................................... 3
Contact Info................................................................................................................................ 3
Machine Data Sheet................................................................................................................... 4
Identification ............................................................................................................................... 5
SECTION 1: SAFETY....................................................................................................................... 8
Safety Instructions for Machinery............................................................................................... 8
Additional Safety Instructions for Table Saws ......................................................................... 10
Preventing Kickback................................................................................................................. 11
Protecting Yourself from Kickback........................................................................................... 11
Glossary Of Terms................................................................................................................... 12
SECTION 2: CIRCUIT REQUIREMENTS ...................................................................................... 13
220/440V 3-Phase ................................................................................................................... 13
Phase Converter ...................................................................................................................... 14
Grounding................................................................................................................................. 14
Rewiring to 440V...................................................................................................................... 14
SECTION 3: SET UP...................................................................................................................... 16
Set Up Safety........................................................................................................................... 16
Unpacking ................................................................................................................................ 16
Items Needed For Set Up ........................................................................................................ 16
Inventory................................................................................................................................... 17
Hardware Recognition Chart.................................................................................................... 19
Clean Up .................................................................................................................................. 20
Site Considerations.................................................................................................................. 20
Moving & Placing Base Unit..................................................................................................... 21
Extension Tables...................................................................................................................... 22
Scale ........................................................................................................................................ 23
Rip Fence................................................................................................................................. 24
Crosscut Table......................................................................................................................... 26
Crosscut Fence........................................................................................................................ 27
Sliding Table ............................................................................................................................ 28
Main Blade ............................................................................................................................... 29
Aligning Scoring Blade Set ...................................................................................................... 31
Adjusting Scoring Blade Kerf ................................................................................................... 31
Scale Alignment ....................................................................................................................... 31
Dust Collection......................................................................................................................... 32
Power Cord .............................................................................................................................. 33
Test Run................................................................................................................................... 33
SECTION 4: OPERATIONS ........................................................................................................... 34
Operation Safety ...................................................................................................................... 34
Operation Tips.......................................................................................................................... 34
Changing Main Blade............................................................................................................... 35
Riving Knife Adjustment........................................................................................................... 36
Adjusting and Replacing Scoring Blade................................................................................... 37
Rip Cutting ............................................................................................................................... 38
Crosscutting ............................................................................................................................. 40
Miter Cutting............................................................................................................................. 42
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: ACCESSORIES......................................................................................................... 43
SECTION 6: MAINTENANCE ........................................................................................................ 46
Schedule .................................................................................................................................. 46
Cleaning ................................................................................................................................... 46
Unpainted Cast Iron ................................................................................................................. 46
Lubrication................................................................................................................................ 47
Maintenance Log...................................................................................................................... 48
SECTION 7: SERVICE ................................................................................................................... 49
About Service........................................................................................................................... 49
Replacing Belts ........................................................................................................................ 49
Blade Tilt .................................................................................................................................. 50
Sliding Table Parallel Adjustment ............................................................................................ 51
Squaring Crosscut Fence to Blade .......................................................................................... 52
Service Log .............................................................................................................................. 53
Troubleshooting........................................................................................................................ 54
Electrical................................................................................................................................... 56
SECTION 8: PARTS....................................................................................................................... 58
Extension Arm Assembly ......................................................................................................... 58
Extension Table Assembly....................................................................................................... 60
Base Assembly ........................................................................................................................ 62
Blade Assembly ....................................................................................................................... 64
Arbor and Dust Hood Assembly............................................................................................... 66
Sliding Table Assembly............................................................................................................ 68
Table Assembly........................................................................................................................ 70
Fence Assembly....................................................................................................................... 72
Motor Assembly ....................................................................................................................... 74
Blade Adjustment Assembly .................................................................................................... 76
Swing Arm Assembly ............................................................................................................... 78
Main Motor Assembly............................................................................................................... 80
WARRANTY AND RETURNS........................................................................................................ 82
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Foreword
Contact Info
We are proud to offer the Model G0451 14"
Sliding Table Saw. This machine is part of a grow-
ing Grizzly family of fine woodworking machinery.
When used according to the guidelines set forth in
this manual, you can expect years of trouble-free,
enjoyable operation and proof of Grizzly’s com-
mitment to customer satisfaction.
If you have any comments regarding this manual,
please write to us at the address below:
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/
O
Bellingham, WA 98227-2069
We are pleased to provide this manual with
the Model G0451. It was written to guide you
through assembly, review safety considerations,
and cover general operating procedures. It repre-
sents our effort to produce the best documenta-
tion possible.
We stand behind our machines. If you have any
service questions or parts requests, please call or
write us at the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
The specifications, drawings, and photographs
illustrated in this manual represent the Model
G0451 as supplied when the manual was pre-
pared. However, owing to Grizzly’s policy of con-
tinuous improvement, changes may be made at
any time with no obligation on the part of Grizzly.
For your convenience, we always keep current
Grizzly manuals available on our website at www.
grizzly.com. Any updates to your machine will be
reflected in these manuals as soon as they are
complete. Visit our site often to check for the lat-
est updates to this manual!
E-Mail: [email protected]
-3-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901
MODEL G0451 14" Sliding Table Saw
Overall Dimensions:
Overall Size................................................................................105½"D (2037⁄8" w/Sliding Table Extended) X 117½"W x 49"H
Table Height......................................................................................................................................................................... 35½"
Table Size (w/Extension Wings) .........................................................................................................................68" W x 39¾" D
Sliding Table Size ............................................................................................................................................983⁄8" W x 13¾" D
Machine Net Weight.......................................................................................................................................................1309 lbs.
Crate Size ......................................................................................................................................1023⁄8" W x 45½" D x 44½" H
Base Footprint.....................................................................................................................................................54½" W x 39" D
Capacities:
Main Blade Diameter.................................................................................................................................................... 12" or 14"
Scoring Blade Diameter ................................................................................................................................................... 120mm
Maximum Depth of Cut at 90˚................................................................................................................................................ 45⁄8
"
Maximum Depth of Cut at 45˚...............................................................................................................................................35⁄16"
Blade Tilt ............................................................................................................................................................................. 0–45˚
Table w/Rip Fence Max Cutting Width ................................................................................................................................ 325⁄8
"
Sliding Table w/Cross Fence Max Cut Width ....................................................................................................................... 125"
Sliding Table w/Cross Fence Max Cut Length..................................................................................................................... 983⁄8
"
Construction:
Sliding Table ................................................................................................................................................................ Aluminum
Machine Frame .................................................................................................................................................................... Steel
Fence ............................................................................................................................................................Extruded Aluminum
Rails ..................................................................................................................................................................... Chromed Steel
Trunnions .......................................................................................................................................................................Cast Iron
Spindle Ball Bearings............................................................................................................................... Sealed and Lubricated
Main Motor:
Arbor.......................................................................................................................................................................................... 1"
Arbor Speed................................................................................................................................................................ 4200 RPM
Motor ..........................................................................................10 HP, 25/12.5A, 3-Phase, 60 HZ, 220/440V (Prewired 220V)
Motor RPM........................................................................................................................................................................... 3450
Ball Bearings.............................................................................................................................................Shielded & Lubricated
Power Transfer..............................................................................................................................................................Belt Drive
Switch..........................................................................................................................Magnetic w/Thermal Overload Protection
Scoring Motor:
Arbor................................................................................................................................................................................... 22mm
Arbor Speed................................................................................................................................................................ 8000 RPM
Motor ................................................................................................1 HP, 3/1.5A, 3-Phase, 60 HZ, 220/440V (Prewired 220V)
Motor RPM........................................................................................................................................................................... 3450
Ball Bearings.............................................................................................................................................Shielded & Lubricated
Power Transfer..............................................................................................................................................................Belt Drive
Features:
......................................................................................................................................................Blade Guard w/2½" Dust Port
.........................................................................................................................................................................5" Main Dust Port
...................................................................................................................................................... Adjustable Scoring Knife Kerf
................................................................................................................................................................ Adjustable Riving Knife
............................................................................................................................Micro Adjustable, Single Lever Locking Fence
Specifications, while deemed accurate, are not guaranteed.
-4-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification
E
C
F
D
B
A
G
I
H
Figure 1. Main view of machine features and controls.
A. Crosscut Table—Provides a wide, stable
platform for supporting full-size panels during
crosscutting operations.
F. Rip Fence—Fully adjustable with micro-
adjustment knob for precision adjustments.
Fence face can be positioned for standard
cutting operations, or in the lower position for
blade guard clearance during narrow ripping
operations.
B. Flip Stops—Used for quick measurements
for crosscutting.
C. Crosscut Fence—Used during crosscutting
operations. Features a scale and multiple
flip-style stop blocks for precise, repeatable
crosscutting operations.
G. Control Panel—Features push-button con-
trols for operating the many features of the
saw.
H. Blade Angle Handwheel—Adjusts the angle
D. Sliding Table—Conveniently glides the
workpiece through the blade with effortless
precision and ease.
of the saw blades.
I. Blade Elevation Handwheel—Adjusts the
height of the main saw blade.
E. Blade Guard—Fully-adjustable blade guard
maintains maximum protection around the
saw blade and a 2½" dust port effectively
extracts dust from the cutting operation.
-5-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
O
L
Q
K
M
N
J
P
Figure 2. Fence controls.
Figure 3. Blades.
J. Fence Assembly Lock Down Lever—
Secures the fence assembly into position
along the fence rail.
O. Riving Knife—Maintains kerf opening dur-
ing cutting operations. This function is crucial
to preventing kickback caused by the kerf
closing behind the blade.
K. Rip Fence Scale—Allows precise measure-
ment of rip cutting operations.
P. Main Blade—Performs the cutting opera-
tions.
L. Forward/Backward Slide Lock Handle—
Secures the aluminum fence piece on its
forward/backward slide track.
Q. Scoring Blade—Small cutting blade that
rotates opposite the main saw blade. The
blade scores the workpiece before the actual
cutting operation is performed preventing
tear-out in laminate materials. The scoring
blade is adjustable forward and backward,
up and down, and in thickness of kerf.
M. Micro-Adjust Lock Knob—Secures the
fence after it has been adjusted with the
micro-adjustment knob.
N. Micro-Adjust Knob—Precisely adjusts the
fence.
-6-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Y
X
W
Z
AA
R
S
V
T
U
Figure 4. Control panel close-up.
Figure 5. Scoring blade adjustment knobs.
R. Power ON/OFF Button—Connects power to
Y. Scoring Blade Elevation Knob—Adjusts
all motors in the saw.
the height of the scoring blade.
S. Power Indicator Light—Indicates a live
Z. Scoring Blade Alignment Knob—Adjusts
the alignment of the scoring blade and the
main blade.
connection to power.
T. Main Blade OFF Button—Stops the main
saw blade.
AA. Secondary EMERGENCY STOP Button—
Disconnects power to all motors in the motor
cabinet.
U. Scoring Blade OFF Button—Stops the
scoring blade.
V. Primary EMERGENCY STOP Button—
Disconnects power to all motors in the motor
cabinet.
W. Scoring Blade ON Button—Starts the scor-
ing blade. Note—The main saw blade must
be ON for the scoring blade to start.
X. Main Blade ON Button—Starts the main
saw blade.
-7-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
For Your Own Safety, Read Instruction
Manual Before Operating this Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words which are intended to convey the level of
importance of the safety messages. The progression of symbols is described below. Remember
that safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
1. READ THROUGH THE ENTIRE MANUAL
BEFORE STARTING MACHINERY.
Machinery presents serious injury hazards
to untrained users.
4. ALWAYS USE HEARING PROTECTION
WHEN OPERATING MACHINERY.
Machinery noise can cause permanent
hearing damage.
5. WEAR PROPER APPAREL. DO NOT
wear loose clothing, gloves, neckties, rings,
or jewelry which may get caught in moving
parts. Wear protective hair covering to con-
tain long hair and wear non-slip footwear.
2. ALWAYS USE ANSI APPROVED
SAFETY GLASSES WHEN OPERATING
MACHINERY. Everyday eyeglasses only
have impact resistant lenses, they are
NOT safety glasses.
6. NEVER OPERATE MACHINERY WHEN
TIRED, OR UNDER THE INFLUENCE OF
DRUGS OR ALCOHOL. Be mentally alert
at all times when running machinery.
3. ALWAYS WEAR AN ANSI APPROVED
RESPIRATOR WHEN OPERATING
MACHINERY THAT PRODUCES DUST.
Wood dust is a carcinogen and can cause
cancer and severe respiratory illnesses.
-8-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions for Machinery
7. ONLY ALLOW TRAINED AND PROP-
17. REMOVE ADJUSTING KEYS AND
ERLY SUPERVISED PERSONNEL TO
OPERATE MACHINERY. Make sure
operation instructions are safe and clearly
understood.
WRENCHES. Make a habit of checking for
keys and adjusting wrenches before turn-
ing machinery ON.
18. CHECK FOR DAMAGED PARTS
BEFORE USING MACHINERY. Check
for binding and alignment of parts, broken
parts, part mounting, loose bolts, and any
other conditions that may affect machine
operation. Repair or replace damaged
parts.
8. KEEP CHILDREN AND VISITORS AWAY.
Keep all children and visitors a safe dis-
tance from the work area.
9. MAKE WORKSHOP CHILD PROOF. Use
padlocks, master switches, and remove
start switch keys.
19. USE RECOMMENDED ACCESSORIES.
Refer to the instruction manual for recom-
mended accessories. The use of improper
accessories may cause risk of injury.
10. NEVER LEAVE WHEN MACHINE IS
RUNNING. Turn power OFF and allow all
moving parts to come to a complete stop
before leaving machine unattended.
20. DO NOT FORCE MACHINERY. Work at
the speed for which the machine or acces-
sory was designed.
11. DO NOT USE IN DANGEROUS
ENVIRONMENTS. DO NOT use machin-
ery in damp, wet locations, or where any
flammable or noxious fumes may exist.
21. SECURE WORKPIECE. Use clamps or
a vise to hold the workpiece when practi-
cal. A secured workpiece protects your
hands and frees both hands to operate the
machine.
12. KEEP WORK AREA CLEAN AND WELL
LIT. Clutter and dark shadows may cause
accidents.
22. DO NOT OVERREACH. Keep proper foot-
13. USE A GROUNDED EXTENSION CORD
RATEDFORTHEMACHINEAMPERAGE.
Undersized cords overheat and lose power.
Replace extension cords if they become
damaged. DO NOT use extension cords
for 220V machinery.
ing and balance at all times.
23. MANY MACHINES WILL EJECT THE
WORKPIECETOWARDTHEOPERATOR.
Know and avoid conditions that cause the
workpiece to "kickback."
14. ALWAYS DISCONNECT FROM POWER
24. ALWAYS LOCK MOBILE BASES
(IF USED) BEFORE OPERATING
MACHINERY.
SOURCE
BEFORE
SERVICING
MACHINERY. Make sure switch is in OFF
position before reconnecting.
25. BE AWARE THAT CERTAIN WOODS
MAY CAUSE AN ALLERGIC REACTION
in people and animals, especially when
exposed to fine dust. Make sure you
know what type of wood dust you will be
exposed to and always wear an approved
respirator.
15. MAINTAIN MACHINERY WITH CARE.
Keep blades sharp and clean for best and
safest performance. Follow instructions for
lubricating and changing accessories.
16. MAKE SURE GUARDS ARE IN PLACE
AND WORK CORRECTLY BEFORE
USING MACHINERY.
-9-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions for Table Saws
1. SAFETY ACCESSORIES. Always use the
blade guard and riving knife on all ''through-
sawing'' operations. Through-sawing oper-
ations are those when the blade cuts com-
pletely through the workpiece.
7. RIVING KNIFE ALIGNMENT. Only oper-
ate the saw if the riving knife is aligned with
the main blade.
8. REACHING OVER SAW BLADE. Never
reach behind or over the blade with either
hand while the saw is running. If kick-
back occurs while reaching over the blade,
hands or arms could be pulled into the
spinning saw blade.
2. KICKBACK. Be familiar with kickback.
Kickback happens when the workpiece is
thrown towards the operator at a high rate
of speed. Until you have a clear under-
standing of kickback and how it occurs, DO
NOT operate this table saw!
9. RIP FENCE AND CROSSCUT FENCE
USAGE. When using the crosscut fence,
the workpiece should never contact the rip
fence while the saw blade is cutting.
3. WORKPIECE CONTROL. Make sure the
workpiece is placed in a stable position on
the table and is either supported by the rip
fence or the crosscut table during cutting
operations.
10. STALLED BLADE. Turn the saw OFF
before "free-ing" a stalled saw blade.
4. PUSH STICK. Always use a push stick
11. BLADE HEIGHT. Always adjust the blade
when ripping narrow stock.
to the proper height above the workpiece.
5. OPERATOR POSITION. Never stand or
have any part of your body directly in-line
with the cutting path of the saw blade.
12. DAMAGED SAW BLADES. Never use
blades that have been dropped or other-
wise damaged.
6. AWKWARD OPERATIONS. Avoid awk-
ward operations and hand positions where
a sudden slip could cause your hand to
move into the spinning saw blade.
13. EXPERIENCING DIFFICULTIES. If at
any time you are experiencing difficulties
performing the intended operation, stop
using the machine! Contact our Service
Department at (570) 546-9663.
Like all machines there is danger associ-
ated with the Model G0451. Accidents are
frequently caused by lack of familiarity or
failure to pay attention. Use this machine
with respect and caution to lessen the pos-
sibility of operator injury. If normal safety
precautions are overlooked or ignored, seri-
ous personal injury may occur.
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
Failure to do so could result in serious per-
sonal injury, damage to equipment, or poor
work results.
-10-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Make multiple, shallow passes when per-
forming a non-through cut. Making a deep
non-through cut will greatly increase the
chance of kickback.
Statistics prove that most common acci-
dents among table saw users can be linked
to kickback. Kickback is typically defined
as the high-speed expulsion of stock from
the table saw toward its operator. In addi-
tion to the danger of the operator or oth-
ers in the area being struck by the flying
stock, the operator’s hands can be pulled
into the blade during the kickback.
Feed cuts through to completion. Anytime
you stop feeding a workpiece that is in the
middle of a cut, the chance of binding, result-
ing in kickback, is greatly increased.
Protecting Yourself
from Kickback
Preventing Kickback
Below are tips to reduce the likelihood of
kickback:
Even if you know how to prevent kickback,
it may still happen. Here are some tips to
reduce the likelihood of injury if kickback
DOES occur:
•
Never attempt freehand cuts. If the workpiece
is not fed perfectly parallel with the blade, a
kickback will likely occur. Always use the
rip fence or crosscut fence to support the
workpiece.
•
Never, for any reason, place your hand
behind the blade. Should kickback occur,
your hand will be pulled into the blade.
•
Make sure the riving knife is always aligned
with the blade. A misaligned riving knife can
cause the workpiece to bind or stop the flow
of the cut, resulting in an increased chance
of kickback. If you think that your riving knife
is not aligned with the blade, check it imme-
diately!
•
Stand to the side of the blade during every
cut. If a kickback does occur, the thrown
workpiece usually travels directly in front of
the blade.
•
•
Always wear safety glasses or a face shield.
In the event of a kickback, your eyes and
face are the most vulnerable part of your
body.
•
•
Ensure that your table slides parallel with the
blade; otherwise, the chances of kickback
are extreme. Take the time to check and
adjust the sliding table.
Use a pushstick to keep your hands farther
away from the moving blade. If a kickback
occurs, the push stick will most likely take
the damage that your hand would have
received.
Use the riving knife whenever performing a
through cut. The riving knife helps maintain
the kerf in the workpiece after it is cut, there-
fore, reducing the chance of kickback.
-11-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary Of Terms
The following is a list of common definitions, terms and phrases used throughout this manual as they relate
to this table saw and woodworking in general. Become familiar with these terms for assembling, adjusting
or operating this machine. Your safety is VERY important to us at Grizzly!
Arbor: Metal shaft extending from the drive
Non-Through Cut: A sawing operation that
requires the removal of the blade guard and riv-
ing knife. Dado and rabbet cuts are considered
Non-Through Cuts because the blade does
not protrude above the top face of the wood
stock. Deep Non-Through Cuts must be made
with multiple, light passes to reduce chance
of kickback. Always remember to re-install the
blade guard and riving knife after performing a
non-through cut.
mechanism, to which saw blade is mounted.
Bevel Edge Cut: Tilting the arbor and saw blade
to an angle between 0° and 45° to cut a bev-
eled edge onto a workpiece.
Blade Guard: Metal or plastic safety device that
mounts over the saw blade. Its function is to
prevent the operator from coming into contact
with the saw blade.
Perpendicular: Lines or planes that intersect
and form right angles (i.e. the blade is perpen-
dicular to the table surface).
Crosscut: Cutting operation in which the cross-
cut fence is used to cut across the grain, or
across the shortest width of the workpiece.
Push Stick: Safety device used to push the
workpiece through a cutting operation. Used
most often when rip cutting thin workpieces.
Dado Blade: Blade or set of blades that are used
to cut grooves and rabbets.
Dado Cut: Cutting operation that uses a dado
blade to cut a flat bottomed groove into the
face of the workpiece.
Rabbet: Cutting operation that creates an L-
shaped channel along the edge of the
workpiece.
Featherboard: Safety device used to keep the
workpiece against the rip fence and against the
table surface.
Riving Knife (Splitter): Metal plate located
behind the blade. It maintains the kerf opening
in the wood when performing a cutting opera-
tion.
Kerf: The resulting cut or gap in the workpiece
after the saw blade passes through during a
cutting operation.
Straightedge: A tool used to check the flatness,
parallelism, or consistency of a surface(s).
Kickback: An event in which the workpiece is
propelled back towards the operator at a high
rate of speed.
Through Cut: A sawing operation in which the
workpiece is completely sawn through.
Rip Cut: Cutting operation in which the rip fence
is used to cut with the grain, or across the wid-
est width of the workpiece.
Parallel: Being an equal distance apart at every
point along two given lines or planes. I.e. the
rip fence face is parallel to the face of the saw
blade.
-12-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: CIRCUIT REQUIREMENTS
Connection Type
220/440V 3-Phase
Because of the high amperage draw from this
machine, we recommend that you hardwire it
directly to your circuit breaker and install a locking
shut-off lever (see Figure 6) near the machine as
a way to quickly disconnect the power and pre-
Serious personal injury could occur if you
vent accidental starting.
connect your machine to the power source
before you have completed the set up pro-
cess. DO NOT connect the machine to the
power source until instructed to do so.
Wiring
The Model G0451 is prewired for 220V 3-phase
operation. If 440 voltage is required, rewire the
machine according to the instructions on Page 14
and follow the circuit requirements on this page.
Amperage Draw
The Model G0451 has a 10 HP main motor and
a 1 HP scoring blade motor; combined they will
draw the following amps:
Figure 6. A power disconnect is preferable to
high current plugs and receptacles.
Motor Draw at 220V ..............................28 Amps
Motor Draw at 440V .............................. 14 Amps
A fire may occur if your particular electrical
configuration does not comply with local and
state codes. The best way to ensure compli-
ance is to check with your local municipality
Minimum Circuit Requirements
Only connect your machine to a circuit that meets
the requirements below. Check to see if the wires
and circuit breaker in your circuit are capable of
handling the amperage draw from your machine,
as well as any other machines that could be
operating on the same circuit. If you are unsure,
consult a qualified electrician.
or a qualified electrician.
220V Circuit.............................................30 Amp
440V Circuit.............................................15 Amp
Minimum Cord Requirements
Use the following type of cord to connect your
machine to power (a cord is not provided):
Cord............................................................4 wire
Gauge.................................................. 10 Gauge
-13-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Phase Converter
Rewiring to 440V
When using a phase converter, the power from
the manufactured power leg (sometimes called
the wild wire) can fluctuate. Connect the manu-
factured power leg to the S terminal to prevent
damage to the transformer. The wire from the S
terminal can handle some fluctuation because it
goes directly to the motor. The power going to
the R and T terminals goes to the transformer
and must be consistent to prevent damage. See
the phase converter instruction manual for more
information.
The Model G0451 can be rewired for 440V opera-
tion. This rewiring job consists of disconnecting
the saw from the power source, changing the
connections on the voltage transformer, chang-
ing the overload relays for the scoring motor, and
rewiring the cutting motor and scoring motor.
The necessary overload relay for this procedure
can be purchased by calling our customer ser-
vice number at (800) 523-4777 and ordering part
number P04510014A.
This procedure takes moderate electrical skill
and the rewiring job must be inspected by a quali-
fied electrician before the saw is connected to the
power source. Also, the motors can be accessed
easier for rewiring if the blade is moved to 0˚ (90˚
to table) before beginning.
Grounding
In the event of an electrical short, grounding
reduces the risk of electric shock. This tool is
equipped with a power cord that has a grounding
wire, which must be properly connected to the
grounding prong on the plug; likewise, the outlet
must be properly installed and grounded. All elec-
trical connections must be made in accordance
with local codes and ordinances.
To rewire the Model G0451 for 440V opera-
tion:
1. Disconnect the saw from the power
source!
2. Open the electrical panel and locate the volt-
age transformer shown in Figure 7.
Improper connections of the electrical-grounding
conductor increases the risk of electric shock.
Check with a qualified electrician or one of our
service personnel if you do not understand
the grounding instructions, or if you doubt the
machine is properly grounded.
Voltage
Transformer
Electrical
Access Panel
Scoring
Motor Relay
Main Motor
Relay
Electrocution or fire could
result if this machine is
not grounded correctly
or if your electrical con-
figuration does not com-
ply with local and state
codes. Ensure compliance
by checking with a quali-
fied electrician!
Figure 7. Inside view of the control panel.
-14-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
3. At the voltage transformer, pull the fuse that
is in the “220” slot and push it into the “440”
slot (see Figure 8).
6. Open the motor cabinet door and remove the
motor wiring covers from the main motor and
the scoring motor (see Figure 10).
Scoring
Motor
Main
Motor
Fuse
Figure 10. Motor locations.
Figure 8. Fuse installed at the 220V location.
4. Turn the dial (Figure 9) on the main motor
7. Rewire the motors as shown on the diagrams
that are placed on the inside of the motor wir-
ing covers.
overload relay to 15A.
Scoring
Motor Relay
Main Motor
Overload
Relay Dial
Figure 9. Motor overload relays.
5. Remove the scoring motor overload relay and
replace it with the 440V overload relay. Set
the overload relay dial to 2A.
-15-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: SET UP
Set Up Safety
Unpacking
The Model G0451 was carefully packed when it
left our warehouse. If you discover the machine
is damaged after you have signed for delivery,
please immediately call Customer Service at
(570) 546-9663 for advice.
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu-
al to become familiar with
the controls and opera-
tions before starting the
machine!
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the con-
dition of your shipment, you should inventory the
contents.
Wear safety glasses dur-
ing the entire set up pro-
cess!
Items Needed For
Set Up
The Model G0451 is a
heavy machine that
weighs over 1300 lbs.
Serious personal injury
may occur if safe mov-
ing methods are not fol-
lowed. To be safe, you
will need assistance and
power equipment when
moving the shipping
crate and removing the
machine from the crate.
The following items are needed to complete the
set up process, but are not included with your
machine:
Description
Qty
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Safety Glasses (for each person) .............. 1
Power Lifting Equipment ............................ 1
Lifting Straps (1500 lb capacity)................. 2
An Assistant ............................................... 1
Straightedge 4' (or longer) ......................... 1
Main Blade 12" or 14" ................................ 1
Phillips Head Screwdriver .......................... 1
Hex Wrenches 3, 4, 6, & 8mm..........1 Each
Wrenches or Sockets, 16 & 18mm ...1 Each
Dust Collection System.............................. 1
5" Dust Hose (length as needed)............... 1
5" Hose Clamp ........................................... 2
2½" Dust Hose (length as needed)............ 1
Power Cord (length as needed)................. 1
Power Disconnect Box............................... 1
-16-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Box 4: (Figure 13)
I. Crosscut Table ........................................... 1
Qty
Inventory
After all the parts have been removed from the
boxes, you should have the following items:
Box 1: (Figure 11)
Qty
A. Support Brace ............................................ 1
B. Small Extension Table................................ 1
C. Large Extension Table ............................... 1
I
A
C
Figure 13. Box 4 contents.
B
Box 5: (Figure 14)
Qty
J. Sliding Table End Handle........................... 1
K. Sliding Table Lock Plate............................. 1
Box 6: (Figure 14)
Qty
L. Flip Stops ................................................... 2
M. Edge Shoe.................................................. 1
N. Hold Down.................................................. 1
Figure 11. Box 1 contents.
Box 2 & 3: (Figure 12)
Qty
D. Crosscut Fence .......................................... 1
E. Rip Fence Round Rail................................ 1
F. Crosscut Table Brace................................. 1
G. Rip Fence Scale......................................... 1
H. Rip Fence................................................... 1
M
L
K
N
D
E
J
F
G
H
Figure 14. Box 5 & 6 contents.
Figure 12. Box 2 & 3 contents.
-17-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Box 7: (Figure 15)
Qty
Box 7 Cont.:
S. Toolbox Cont.
Qty
O. Rip Fence Body.......................................... 1
P. Blade Guard/Dust Hood............................. 1
Q. Push Stick .................................................. 1
R. Dust Collection Hose Support.................... 1
— Hardware............................................... 1
• Cap Screw M10-1.5 x 30........................ 4
• Cap Screw M10-1.5 x 20...................... 10
• Hex Nut M10-1.5.................................... 4
• Lock Washer 10mm............................. 14
• Flat Washer 10mm .............................. 10
• Set Screw M6-1.0 x 12........................... 6
• Stud M12-1.75 x 115............................... 4
• Hex Nut M12-1.75 ................................ 12
• Flat Washer 12mm .............................. 10
• Lock Washer 12mm............................... 4
• Lock Washer 8mm................................. 1
• Cap Screw M8-1.25 x 16 ....................... 1
• End Washer 8mm.................................. 1
• Adjustable Ring & Set Screw................. 1
• Center Stud M8-1.25 x 10...................... 1
• Fiber Washer 8mm................................ 1
• T-Nut M8-1.25........................................ 2
• T-Nut M12-1.75....................................... 2
• Handle M12-1.75 x 12 ............................ 1
• Adjustable Handle M12-1.75 x 55 .......... 1
• Handle M10-1.5 x 12.............................. 2
• Knob M10-1.5 x 70................................. 1
• Knob M8-1.25 x 25 ................................ 1
• Knob M8-1.25 x 50 ................................ 2
• Knob M8-1.25 ........................................ 1
• T-Bolt M8-1.25 x 60 ............................... 1
• Flat Washer 8mm .................................. 3
• Feet M16-2.0 x 100................................ 4
O
P
Q
R
Figure 15. Box 7 contents.
Box 7 Cont.: (Figure 16)
Qty
S. Toolbox....................................................... 1
— Flat Belt 15 x 787mm............................. 1
— Riving Knife ........................................... 1
— Arbor Wrenches..................................... 2
— Hose Clamps 2½".................................. 2
In the event that any nonproprietary parts are
missing (e.g. a nut or a washer), we would be
glad to replace them, or for the sake of expedi-
ency, replacements can be obtained at your local
hardware store.
Figure 16. Box 7 contents continued.
-18-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Recognition Chart
-19-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Clean Up
Site Considerations
The unpainted surfaces are coated with a waxy
oil to protect them from corrosion during ship-
ment. Remove this protective coating with a sol-
vent cleaner or citrus-based degreaser such as
Grizzly’s G7895 Degreaser. To clean thoroughly,
some parts may need to be removed. For opti-
mum performance from your machine, make
sure you clean all moving parts or sliding
contact surfaces that are coated. Avoid chlo-
rine-based solvents, such as acetone or brake
parts cleaner, as they may damage painted sur-
faces should they come in contact. Always follow
the manufacturer’s instructions when using any
type of cleaning product.
Floor Load
The Model G0451 weighs 1309 lbs. and has a
base footprint of 54½" W x 39" D. Most commer-
cial floors are suitable for your machine. Some
residential floors may require additional reinforce-
ment to support both the machine and operator.
Working Clearances
Consider existing and anticipated needs, size of
material to be processed through each machine,
and space for auxiliary stands, work tables or
other machinery when establishing a location for
your saw. See Figure 17 for the maximum work-
ing clearances of the Model G0451.
Gasoline and petroleum
products have low flash
points and could cause
an explosion or fire if
used to clean machinery.
DO NOT use gasoline or
petroleum products to
clean the machinery.
226"
Many of the solvents
commonly used to clean
machinery can be toxic
when inhaled or ingest-
ed. Lack of ventilation
while using these sol-
vents could cause seri-
ous personal health risks
or fire. Take precautions
from this hazard by only
using cleaning solvents
in a well ventilated area.
Figure 17. Working clearances.
Unsupervised children and
visitors inside your shop
could cause serious per-
sonal injury to themselves.
Lock all entrances to the
shop when you are away and
DO NOT allow unsupervised
children or visitors in your
shop at any time!
-20-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving & Placing
Base Unit
DO NOT lift the table saw any higher than
necessary to clear the floor. Serious per-
sonal injury and damage to the machine
may occur if safe moving methods are not
followed.
The Model G0451 is a
heavy machine that
weighs over 1300 lbs.
Serious personal injury
may occur if safe mov-
ing methods are not fol-
lowed. To be safe, you
will need assistance and
power equipment when
moving the shipping
crate and removing the
machine from the crate.
3. Lift the saw base unit and move it to your
predetermined location.
4. Before lowering the saw into position, place
safety blocks under the frame and thread the
four foot studs into the frame at least half of
their length.
5. Remove the safety blocks and lower the saw
onto the feet as shown in Figure 19 and
remove the forklift straps.
Use lifting straps with a minimum of 1500
lbs. lifting capacity. If the lifting strap
breaks, serious personal injury may occur.
To remove the saw base unit from the crate
pallet:
1. Remove the top of the crate and position the
forklift forks together and directly above the
saw.
Figure 19. Foot studs placed in base feet.
2. Place two lifting straps over the forks and
attach the ends to the lifting bolts as shown
in Figure 18.
6. Place a level on the saw table and adjust
foot studs so the saw table is level from left-
to-right and from front-to-back. This will allow
the table to slide smoothly.
7. Lock the foot studs in position by tightening
their jam nuts against the machine body.
Figure 18. Lifting the saw base unit.
-21-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Attach the large extension table with four
M10-1.5 x 20 cap screws, lock washers, and
flat washers as shown in Figure 21.
Extension Tables
Components and Hardware Needed:
Qty
Large Extension Table .......................................1
Small Extension Table........................................1
Support Brace ....................................................1
Dust Collection Hose Support............................1
Cap Screws M10-1.5 x 30..................................4
Cap Screws M10-1.5 x 20..................................6
Hex Nuts M10-1.5 ..............................................2
Lock Washers 10mm........................................10
Flat Washers 10mm ...........................................6
Set Screws M6-1 x 12........................................6
Tools Needed:
Qty
An Assistant .......................................................1
Hex Wrench 3mm...............................................1
Hex Wrench 8mm...............................................1
Socket or Wrench 16mm....................................1
Straightedge 4' (or longer)..................................1
Figure 21. Large extension table attachment.
4. Attach the support brace (Figure 22) to the
table with two M10-1.5 x 30 cap screws and
lock washers. Note—Do not attach the brace
to the extension table until the next step.
To install the extension tables:
1. Thread the set screws into the small holes
in both extension tables. Make sure the set
screws do not stick out from the mating sur-
face.
Dust Collection
Hose Support
Note—Do not completely tighten the bolts in the
following steps until the tables are leveled.
Support Brace
2. Attach the small extension table with two
M10-1.5 x 20 cap screws, lock washers,
and flat washers as shown in Figure 20.
Note—Get assistance positioning the tables
and holding them in place while installing.
Figure 22. Support brace and dust collection
hose support installation.
5. Place the dust collection hose support over
the support brace as shown in Figure 22
and thread M10-1.5 x 30 cap screws with
lock washers through the remaining support
brace holes and secure with hex nuts.
Figure 20. Small extension table attachment.
-22-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Check the surfaces of the table with a
straightedge as shown in Figure 23.
Scale
Components and Hardware Needed:
Qty
Rip Fence Scale................................................ 1
Cap Screws M10-1.5 x 20..................................4
Hex Nuts M10-1.5 ..............................................2
Lock Washers 10mm..........................................4
Flat Washers 10mm ...........................................4
Tools Needed:
Qty
Hex Wrench 8mm...............................................1
Socket or Wrench 16mm....................................1
To install the scale:
1. Loosely thread four M10-1.5 x 20 cap screws
with lock and flat washers through the scale
and into the table as shown in Figure 25.
Figure 23. Checking with a straightedge.
7. Use the set screws under both extension
tables to level the top surfaces with the saw
table.
8. When the surfaces are level, thread the bolt
shown in Figure 24 against the underside
of the small extension table to hold it level.
Figure 25. Attaching the scale.
2. Secure the cap screws to the extension
table with M10-1.5 hex nuts, but do not fully
tighten.
3. Line the scale up with the top of the table and
Figure 24. Small extension table support bolt.
tighten the cap screws.
9. Tighten all of the cap screws securing the
tables.
-23-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Slide the rip fence body onto the rail, then
place the adjustable ring on the sliding table
end of the rail and secure the ring with the
set screw as shown in Figure 27.
Rip Fence
Components and Hardware Needed:
Qty
Rip Fence.......................................................... 1
Rip Fence Round Rail....................................... 1
Rip Fence Body................................................. 1
Stud M12-1.75 x 115 .......................................... 4
Hex Nut M12-1.75 ............................................ 12
Flat Washer 12mm ............................................ 8
Lock Washer 12mm........................................... 4
Lock Washer 8mm ............................................ 1
Cap Screw M8-1.25 x 16................................... 1
End Washer 8mm.............................................. 1
Adjustable Ring & Set Screw ............................ 1
Lock Handle M10-1.5 x 12................................. 2
Knob M10-1.5 x 70 ............................................ 1
Tools Needed:
Hex Wrench 3mm...............................................1
Qty
Figure 27. Securing the adjustable ring.
Socket or Wrench 18mm....................................1
6. Thread the lock handles (Figure 28) into the
rip fence body and loosely install the fine
adjustment knob.
To install the rip fence:
1. Thread four M12-1.75 x 115 studs into the
round rail.
Lock
Handles
2. Thread an M12-1.75 hex nut onto each stud
and tighten the nuts against the round rail.
3. Thread an M12-1.75 hex nut and a flat wash-
er half way onto each stud.
4. Insert the studs into the table as shown in
Figure 26. Loosely secure with an M12-1.75
hex nut, lock washer, and a flat washer on
each stud.
Fine Adjustment
Knob
Figure 28. Rip fence handles.
7. Place the end washer on the end of the rip
fence rail and secure it with the M8-1.25 cap
screw and lock washer.
Figure 26. Installing the round rail.
-24-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Slide the aluminum rip fence onto the clamp-
ing plate as shown in Figure 29 and lock it
with the handle on top of the rip fence body.
11. Adjust the height of the rip fence rail, then
tighten all of the nuts against the table as
shown in Figure 31.
Clamping
Plate
Figure 29. Installing the rip fence.
Figure 31. Rip fence rail adjustment nuts.
9. Adjust the nuts on the outside of the table
until the edge of the rip fence is parallel with
the sliding table as shown in Figure 30.
12. Check if the bottom of the rip fence rests on
the surface of the table. Note—The rip fence
will scratch the table surface if the ride height
is not adjusted correctly.
Note—Adjust the nut closest to the sliding
table so the rip fence slides freely, leave the
center two nuts loose, and adjust the outside
nut until the rip fence is parallel with the slid-
ing table.
—If the rip fence does not rest on the table,
then the fence is correctly adjusted.
—If the rip fence does rest on the table,
loosen the set screw shown in Figure
32 and rotate the hex bolt to raise the
roller. Tighten the set screw to lock the ride
height.
Rip
Fence
Sliding
Table
Figure 30. Aligning the fence with the edge of
the sliding table.
10. Check the height of the rip fence rail by slid-
ing the rip fence along the rail and comparing
the gap between the rip fence body and the
table.
Figure 32. Rip fence height adjustment.
-25-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
2. With the help of an assistant, place the cross-
cut table on the pivot pin of the swing arm
and slide the T-nut into the T-slot in the slid-
ing table (see Figure 34).
Crosscut Table
Components and Hardware Needed:
Qty
Crosscut Table ...................................................1
Crosscut Table Brace.........................................1
T-Nut M8-1.25.....................................................2
T-Nut M12-1.75....................................................1
Flat Washer 12mm .............................................1
Adjustable Handle M12-1.75 x 55.......................1
Knob M8-1.25 x 50.............................................2
Flat Washer 8mm...............................................2
Tools Needed:
Qty
An Assistant .......................................................1
To install the crosscut table:
1. Thread the M12-1.75 x 55 adjustable handle,
with a 12mm flat washer, through the cross-
cut table and into a M12-1.75 T-nut as shown
in Figure 33.
Figure 34. Installing the crosscut table.
3. Slide two M8-1.25 T-nuts into the crosscut
table brace.
4. Align the T-nuts in the crosscut table brace
with the holes in the crosscut table and
thread the M8-1.25 x 50 knobs, with 8mm flat
washers, into the T-nuts as shown in Figure
35.
Crosscut
Table Brace
Figure 33. Installing the adjustable handle.
Figure 35. Installing the crosscut table brace.
-26-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Insert the center stud and the T-bolt in the
places indicated in Figure 37.
Crosscut Fence
Components and Hardware Needed:
Qty
Center Stud
Placement
Crosscut Fence ..................................................1
Center Stud M8-1.25 x 10 ..................................1
Fiber Washer 8mm.............................................1
T-Nut M8-1.25.....................................................1
Knob M8-1.25 x 25 .............................................1
Knob M8-1.25.....................................................1
T-Bolt M8-1.25 x 60............................................1
Flat Washer 8mm...............................................1
T-Bolt
Placement
Tools Needed:
Qty
Hex Wrench 6mm...............................................1
To install the crosscut fence:
Figure 37. Crosscut fence placement.
1. Thread the center stud and the fiber washer
5. Secure the crosscut fence with the M8-1.25
knob with an 8mm flat washer threaded onto
the T-bolt.
into the remaining M8-1.25 T-nut.
2. Slide the center stud, an M8-1.25 x 60 T-
bolt, and screw a M8-1.25 x 25 knob into the
crosscut fence as shown in Figure 36.
6. Unlock the crosscut fence extension and
slide the flip stops into the fence as shown in
Figure 38.
Knob
Center Stud
T-Bolt
Figure 36. Crosscut fence assembly.
Figure 38. Stop block installation.
3. Slide the center stud to the end with the plas-
tic cap and tighten it in place.
-27-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Install the lock plate as shown in Figure 40
using 4 of the screws removed in the previ-
ous step.
Sliding Table
Components and Hardware Needed:
QTY
T-Nut M12-1.75....................................................1
Flat Washer 12mm .............................................1
Push Handle M12-1.75 x 12................................1
Edge Shoe..........................................................1
Hold Down..........................................................1
Sliding Table End Handle...................................1
Sliding Table Lock Plate.....................................1
Tools Needed:
QTY
Hex Wrench 4mm...............................................1
To assemble the sliding table components:
Lock Plate
1. Remove the red shipping brace (Figure 39)
and the screws indicated. Set the screws
aside for use in the following steps.
Figure 40. Installing the lock plate.
3. Install the end handle, as shown in Figure
41, using the remaining screws removed in
Step 1.
Red Shipping
Brace
Table Lock
Figure 39. Sliding table.
End Handle
Figure 41. Sliding table end handle.
4. The sliding table is locked in place when the
table lock is in the position shown in Figure
41. Rotate the table lock 180˚ to unlock the
sliding table.
-28-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Slide the M12-1.75 T-nut into the sliding table
and thread in the M12-1.75 x 12 push handle
with a washer as shown in Figure 42.
Main Blade
The Model G0451 is designed to accommodate
either a 12" or a 14" main blade. But any time
you change blade sizes, the riving knife must be
adjusted to match the size of blade you install.
Push
Handle
Components and Hardware Needed:
Qty
Blade 12" or 14" (Not Included) .........................1
Flat Belt 15 x 915mm .........................................1
Riving Knife ........................................................1
Tools Needed:
Arbor Wrenches .................................................2
To install the blade:
Figure 42. Sliding table push handle.
1. Open the motor compartment and remove
the red shipping brackets from both motors.
6. Slide the edge shoe into the table as shown
in Figure 43 when needed.
2. Place the flat belt on the scoring blade arbor
as shown in Figure 44, lift the scoring motor,
and slide the flat belt over the scoring motor
pulley.
Edge
Shoe
Scoring
Blade
Arbor
Flat
Belt
Scoring
Motor
Hold
Down
Figure 44. Flat belt installation.
3. Move the blade tilt to 0˚ and raise the main
blade as far as it will go.
Figure 43. Edge shoe and hold down placement.
7. Slide the hold down onto the table when
needed and lock it in place as shown in
Figure 43.
-29-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Slide the table all the way forward to access
the blade arbor and pull open the blade guard
(see Figure 45).
8. Loosen the riving knife center bolt, slide the
riving knife over the bolt as shown in Figure
47, and slightly tighten.
Riving Knife
Main Blade
Arbor
Figure 47. Installing the riving knife.
Figure 45. Main blade arbor components.
1
9. Position the riving knife about 3mm or ⁄8
"
5. Use the arbor wrench to remove the arbor
nut and arbor flange. Note—The arbor nut
has left hand threads and loosens by turning
clockwise.
away from the nearest carbide tooth on the
main blade. Note—For a quick gauge, use
the 3mm hex wrench to find the correct spac-
ing between the blade and the riving knife, as
shown in Figure 48.
6. Slide the blade over the arbor with the teeth
facing the front of the saw as shown in
Figure 46.
Figure 48. Adjusting the riving knife.
Figure 46. Installing the main blade.
10. Tighten the center bolt to secure the riving
knife in position.
7. Re-install the arbor flange and the arbor nut
and tighten them against the blade as shown
in Figure 46.
11. Move the blade guard back to its original
position, and move the sliding table back to
center.
Note—Wear gloves to protect your hands
when installing or removing blades.
-30-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Aligning Scoring
Blade Set
Adjusting Scoring
Blade Kerf
The kerf of the tapered scoring blade included
with this sliding table saw is adjusted by changing
the height of the scoring blade. See Page 37 for
replacement scoring blade adjusting instructions.
To align the scoring blade set:
1. Move the blade tilt to 0˚ (blade 90˚ to table),
raise the main blade all the way up, and use
the vertical adjustment knob (Figure 49) to
raise the scoring blade to its highest point.
To change the scoring blade kerf:
1. Measure the main blade kerf, then measure
the scoring blade kerf at the table level.
Scoring
Blade Vertical
Adjustment
2. Raise or lower the scoring blade until the kerf
matches the kerf of the main blade.
3. Perform a test cut and check for chip out on
the underside of the test piece. If there is
chip out, make the adjustments necessary to
match the kerfs.
Scoring Blade
Horizontal
Adjustment
Figure 49. Scoring blade adjustment controls.
Scale Alignment
2. Move the rip fence against the main blade (or
scoring blade) as shown in Figure 50.
Before operation, align the rip fence scale with
the blade to ensure accurate measurements.
Tools Needed:
QTY
Hex Wrench 3mm...............................................1
Hex Wrench 8mm...............................................1
To align the fence scale with the blade:
1. Tilt the blade to 0˚, raise the main blade all
the way up, and move the rip fence against
the blade as shown in Figure 50.
2. Loosen the screws securing the scale, line up
the first mark on the scale with the left edge
of the rip fence, then tighten the screws.
Figure 50. Fence used to align blades.
1
3. Set the rip fence to ⁄8", slide the adjustable
3. Use the horizontal adjustment controls to
adjust the scoring blade until the rip fence
can touch both blades.
ring against the fence, and secure the ring to
prevent the fence from contacting the blade.
-31-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Slide the blade guard/dust hood over the riv-
ing knife and attach it with an M8-1.25 x 40
button head cap screw and a flat washer as
shown in Figure 52.
Dust Collection
The Model G0451 is equipped with two dust ports
that should be properly connected to a dust col-
lection system before operation.
Components and Hardware Needed:
Qty
Blade Guard/Dust Hood .....................................1
Flat Washer 8mm...............................................1
Button Head Screw M8-1.25 x 40......................1
Dust Collection System ......................................1
5" Dust Hose (length as needed).......................1
5" Hose Clamp ...................................................2
2½" Dust Hose (length as needed)....................1
2½" Hose Clamp ................................................2
Tools Needed:
Hex Wrench 6mm...............................................1
Phillips Head Screwdriver ..................................1
Figure 52. 2" dust port location.
4. Secure a 2½" dust hose to the dust port
on the top of the blade guard as shown in
Figure 52.
To connect the dust ports to a dust collection
system:
1. Secure a 5" dust hose to the dust port locat-
ed under the saw table (Figure 51).
5. Run the 2½" hose over the hose support
(Figure 53) and connect it to the dust collec-
tion system.
Figure 51. 5" dust port location.
Figure 53. Dust hose support in use.
2. Run the 5" hose to your dust collection sys-
tem.
6. Run a ground wire through the dust hose
and attach the wire to the machine to pro-
tect against static electricity.
-32-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Cord
Test Run
Before installing the power cord, read through
Section 2: Circuit Requirements to check that
your setup follows the safety and circuit require-
ments, and the power cord and plug that you have
chosen meet the requirements for this machine.
Now that the machine is connected to the power
source, it is important to perform a test run to
make sure all the controls are working properly.
Components and Hardware Needed:
Power Cord ........................................................1
Qty
Before starting the saw, make sure you
have performed the preceding assembly
and adjustment instructions, and you have
read through the rest of the manual and
are familiar with the various functions and
safety issues associated with this machine.
Failure to follow this warning could result in
serious personal injury or even death!
Tools Needed:
Phillips Head Screwdriver ..................................1
To connect the saw to the power source:
1. Open the terminal box shown in Figure 54.
To test run the saw:
1. Put on safety glasses and make sure any
bystanders are out of the way and also wear-
ing safety glasses.
2. Insert the key into the control panel and turn
it clockwise.
3. Rotate both of the red EMERGENCY STOP
buttons until they spring up.
Ground
R
S
T
4. Press the main blade button then press the
scoring blade button.
Figure 54. Main terminal box.
—If any problems occur, press the
EMERGENCY STOP button.
2. Feed the power cord through the strain
relief on the bottom of the control panel and
connect the cord to the terminals shown in
Figure 54, then close the terminal box.
—If the main blade is rotating in a counter-
clockwise direction, disconnect the saw
from power and exchange wires R & T in
the terminal box.
Note—When using a phase converter, connect
the manufactured power leg to the S terminal.
The S terminal can handle power fluctuation
because it is wired directly to the motor. The other
wires connect to the transformer and must be
consistent to prevent damage.
—Investigate and correct the problem before
operating the machine further. If you need
help, refer to the Troubleshooting section
in the back of this manual or contact our
Service Department at (570) 546-9663.
3. Shut off the main power at the power
source circuit breaker and install the cord
to the disconnect switch.
-33-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: OPERATIONS
Operation Safety
Operation Tips
Your safety is important. The tips below are
intended to supplement Section 1: Safety. But
remember, no safety list can be comprehensive
of every situation. The operator is ultimately
responsible for their own safety, as well as the
safety of bystanders. Every cutting operation is
uniquely different and may require safety equip-
ment or safety procedures not mentioned in this
manual.
Damage to your eyes, lungs, and ears could
result from using this machine without
proper protective gear. Always wear safety
glasses, a respirator, and hearing protection
when operating this machine.
Please follow these tips EVERY time you use
your saw:
•
Stand to the left of the blade line-of-cut when
performing a cutting operation.
•
Turn OFF the saw and allow the blade to
come to a complete stop before removing the
cut-off piece.
Loose hair and cloth-
ing could get caught in
machinery and cause seri-
ous personal injury. Keep
loose clothing and long
hair away from moving
machinery.
•
•
•
•
Make sure that the riving knife is always
aligned with the main blade before cutting!
Always position the blade guard to the cor-
rect height above the workpiece.
NOTICE
Carefully plan each cutting operation to avoid
injuries.
If you have never used this type of machine
or equipment before, WE STRONGLY REC-
OMMEND that you read books, trade maga-
zines, or get formal training before begin-
ning any projects. Regardless of the con-
tent in this section, Grizzly Industrial will
not be held liable for accidents caused by
lack of training.
When you release the sliding table lock,
make sure that the knob is positioned so that
it will not lock the table during a cut.
-34-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Use the arbor wrench to remove the arbor
nut and arbor flange and pull the old blade
off the arbor.
Changing Main
Blade
Note—The arbor nut has left hand threads
and loosens by turning clockwise.
The Model G0451 will perform best when high
quality, sharp blades are used. Therefore, when-
ever the main blade starts to get dull, we recom-
mend that you have it resharpened or replace it
with a new blade.
6. Slide the new blade over the arbor with the
teeth facing the front of the saw as shown in
Figure 56.
Also, the Model G0451 is designed to accom-
modate either a 12" or a 14" main blade. Any time
you change blade size, adjust the riving knife to
3mm away from the blade you install.
To change the main blade:
1. Disconnect the saw from the power
source!
2. Move the blade tilt to 0˚ (blade 90˚ to table)
and raise the main blade as far as it will go.
3. Move the sliding table all the way forward
to expose the internal blade guard that cov-
ers the blades and riving knife, as shown in
Figure 55.
Figure 56. Replacing the main blade.
7. Re-install the arbor flange and the arbor nut
and tighten them against the blade as shown
in Figure 56.
Note—Wear gloves to protect your hands
when installing or removing blades.
— If you changed the diameter of the blade
during this procedure, adjust the riving
knife according to the instructions titled
Riving Knife Adjustment on Page 36.
8. Move the orange blade guard back into its
original position, next to the blades, and cen-
ter the sliding table.
Figure 55. Internal blade guard exposed.
4. Pull the blade guard away from the blades
to expose the mounting assembly. (The
internal blade guard is held in place with a
magnet.)
-35-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
1
6. Position the riving knife about 3mm or ⁄8
"
Riving Knife
Adjustment
away from the nearest carbide tooth on the
main blade. Note—For a quick gauge, use
the 3mm hex wrench to find the correct spac-
ing between the blade and the riving knife, as
shown in Figure 58.
Whenever the blade size is changed (12" or 14"
blade), the riving knife must be adjusted to 3mm
away from the blade you install.
To adjust the riving knife:
1. Disconnect the saw from the power
source!
2. Move the blade tilt to 0˚ (blade 90˚ to table),
and raise the main blade as far as it will go.
3. Move the sliding table all the way forward to
expose the internal blade guard that covers
the blades and riving knife.
Figure 58. Aligning the riving knife.
4. Pull the blade guard away from the riving
knife to expose the mounting assembly.
(The internal blade guard is held in place
with a magnet.)
7. Tighten the center bolt to secure the riving
knife in position.
8. Move the blade guard back to its original
position, and move the sliding table back to
center.
5. Loosen the riving knife center bolt, slide the
riving knife away from the blade as shown in
Figure 57, and slightly tighten.
Riving Knife
Figure 57. Re-adjusting the riving knife.
-36-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
4. To remove the scoring blade, use the arbor
wrench to remove the arbor nut and arbor
flange (see Figure 60). Note—The arbor nut
has right-hand threads and loosens by turn-
ing counterclockwise.
Adjusting and
Replacing Scoring
Blade
The scoring blade that is included with the sliding
table saw is wedge shaped. The kerf thickness of
this style of scoring blade is adjusted by changing
the height of the scoring blade. Most replacement
scoring blade sets consists of an inner and outer
blade with internal shims. The shims are pro-
vided so the scoring blade set can match the kerf
thickness of the main blade. Figure 59 shows a
replacement scoring blade set laid out for identi-
fication. For optimum performance, replace the
scoring blades when they start to get dull.
Figure 60. Removing the scoring blade.
5. Adjust the width of the scoring blade.
—If you are using a tapered scoring blade,
complete Step 6, then adjust the kerf as
instructed on Page 31 before continuing to
Step 7.
—If you are using a stacked scoring blade
set, measure the main blade and use the
shims to stack the set so the thickness
matches the thickness of the main blade.
Figure 59. Scoring blade set.
6. Install the new scoring blade, re-install the
arbor flange and the arbor nut, and tighten
them against the blade set.
To change the scoring blade:
1. Disconnect the saw from the power
source!
7. Move the orange blade guard back into its
original position, next to the blades, and cen-
ter the sliding table.
2. Move the blade tilt to 0˚ (blade 90˚ to table),
and raise the scoring blade all the way up.
8. Align the scoring blade set to the main blade
as described in the “Aligning Scoring Blade
Set” instructions on Page 31.
3. Move the sliding table all the way forward to
expose the internal blade guard that covers
the blades and riving knife.
9. Perform a test cut and check for chip out on
the underside of the test piece. If there is
chip out, make the adjustments necessary to
match the kerfs.
-37-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Determine which cutting operation will be best
suited for the workpiece to be ripped.
Rip Cutting
—To use the sliding table, read the instruc-
tions titled “Rip cutting with the sliding
table.”
The Model G0451 has the capability of rip cut-
ting full size panels (Figure 61). The sliding table
removes the burden of sliding a large and heavy
panel over a stationary table surface.
—To use the machine as a traditional table
saw, skip ahead to “Rip cutting using the
traditional table saw technique.”
Rip cutting with the sliding table:
1. Drop the crosscut fence into the center stud
hole and rotate it until the spring pin shown
in Figure 63 snaps into the T-slot.
2. Check to make sure the fence is at 90˚ and
adjust it as described in "Squaring Crosscut
Fence to Blade" on Page 52 if necessary.
Center
Figure 61. Rip cutting with the sliding table.
Spring Pin
Stud Hole
This saw also has the capability of rip cutting
smaller boards, using the machine as a traditional
table saw (Figure 62). Smaller, lighter boards
are easier to slide across the stationary cast iron
table surface to the right of the saw blade.
Figure 63. Crosscut fence mounting locations.
3. Slide the protection block against the blade
teeth to calibrate the scale, then tighten the
lock knob. Note—The scale will not be accu-
rate if the protection block is cut.
4. Set a flip stop to the desired width-of-cut.
5. Position the blade guard to the correct height
Figure 62. Traditional rip cutting.
for your workpiece.
6. Load the workpiece onto the table saw. The
set up should look similar to Figure 61.
7. Take all the necessary safety precautions,
then perform the cutting operation.
-38-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Slide the leading end of the rip fence so it is
even with the center of the main saw blade
as shown in Figure 66. Note—This technique
allows the finished cut-off piece to “fall” away
from the blade when the cutting operation
is complete; reducing the possibility of kick-
back.
Rip cutting using the traditional table saw
technique:
1. Slide the crosscut table out of the way.
2. Lock the sliding table into a stationary posi-
tion (see Figure 64).
Table Lock
Figure 66. Rip fence even with center of blade
Figure 64. Sliding table lock.
(Blade guard removed for clarity).
3. Place the fence in the vertical position for
larger workpieces, or in the horizontal posi-
tion for angled cuts and for small workpieces
(see Figure 65).
5. Lift the lock lever and position the rip fence to
approximately the desired width-of-cut.
6. Tighten down the micro-adjust lock knob
(Figure 67) and turn the micro-adjust knob to
zero in on the desired width-of-cut.
Micro-Adjust
Lock Knob
Vertical
Micro-Adjust
Knob
Lock
Lever
Horizontal
Figure 65. Rip fence positions.
Figure 67. Rip fence micro-adjusting controls.
7. Push down the lock lever, then perform the
cutting operation.
-39-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Lastly, this machine has the capability of cross-
cutting workpieces while using the rip fence as a
cut-off gauge (Figure 70).
Crosscutting
The Model G0451 can crosscut full size panels
with the fence in the forward or rear position,
although it is easier to load full size panels with
the crosscut fence mounted in the forward posi-
tion (see Figure 68).
Forward Mounted
Crosscut Fence
Figure 70. Crosscutting workpieces
using the rip fence as a cut-off gauge.
Determine which cutting operation will be best
suited for the workpiece to be crosscut.
Figure 68. Crosscutting full size panel.
—If you will be crosscutting full size panels,
then skip ahead to “Crosscutting full size
panels.”
Mounting the crosscut fence in the rear position
(Figure 69) gives greater stability for crosscutting
smaller panels.
—If you will be crosscutting smaller panels,
then skip ahead to “Crosscutting smaller
panels.”
Rear Mounted
Crosscut Fence
—If you will be crosscutting workpieces using
the rip fence as a cut-off gauge, then skip
ahead to “Crosscutting using the rip fence
as a cut-off gauge.”
Figure 69. Crosscutting smaller panels.
-40-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Crosscutting full size panels:
4. Load the workpiece onto the table saw. The
set up should look similar to Figure 69.
1. Install the crosscut fence in the forward
mounting points shown in Figure 71 and lock
it in place.
5. Once all the necessary safety precautions
have been taken, perform the cutting opera-
tion.
2. Check to make sure the fence is at 90˚ and
adjust it as described in "Squaring Crosscut
Fence to Blade" on Page 52 if necessary.
Crosscutting using the rip fence as a cut-off
gauge:
1. Install the crosscut fence in the rear mount-
ing points shown in Figure 71 and lock it in
place.
Rear Mounting
Points
2. Check to make sure the fence is at 90˚ and
adjust it as described in "Squaring Crosscut
Fence to Blade" on Page 52 if necessary.
3. Position the rip fence for the desired width.
4. Load the workpiece onto the table saw. The
set up should look similar to Figure 70.
Forward
Mounting Points
5. Slide the leading end of the rip fence behind
the back edge of the blade as shown in
Figure 72.
Figure 71. Crosscut fence mounting points.
3. Set either flip stop to the desired width-of-cut.
Note—Extend the crosscut fence slide if the
workpiece is more than 74".
4. Load the workpiece onto the table saw. The
set up should look similar to Figure 68.
5. Once all the necessary safety precautions
have been taken, perform the cutting opera-
tion.
Crosscutting smaller panels:
1. Install the crosscut fence in the rear mount-
ing points shown in Figure 71 and lock it in
place.
Figure 72. Correct rip fence position when using
it as a cut-off gauge.
2. Check to make sure the fence is at 90˚ and
adjust it as described in "Squaring Crosscut
Fence to Blade" on Page 52 if necessary.
6. Take all the necessary safety precautions,
then perform the cutting operation.
3. Set either flip stop to the desired width-of-cut.
Note—Extend the crosscut fence slide if the
workpiece is more than 74".
-41-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Rotate the fence to the desired angle and
Miter Cutting
use the lock knob to lock the fence in place.
4. Position the flip stop according to the length
of the workpiece you want to cut off to the left
of the blade.
The miter fence allows miter cuts from 0˚ through
135˚. The table mounted miter scale has a resolu-
tion of 1˚.
5. Load the workpiece onto the table saw. The
set up should look similar to Figure 74.
To perform a miter cut:
1. Slide the crosscut table to the front edge of
the sliding table and lock it in place.
2. Place the crosscut fence center stud in the
center stud hole of the crosscut table. The
fence can be installed as shown in Figure 73
for 90˚ to 135˚ cuts, or as shown in Figure 74
for 0˚ to 90˚ cuts.
Figure 74. Example of miter cutting operation.
6. Once all the necessary safety precautions
have been taken, perform the cutting opera-
tion.
Figure 73. Fence set-up for 90˚ to 135˚ cuts.
-42-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: ACCESSORIES
G7895—Citrus Degreaser
G5562—SLIPIT® 1 Qt. Gel
This citrus based degreaser is perfect for clean-
ing cosmoline off of new equipment. It also works
for cleaning auto parts, tools, concrete, and
porcelain surfaces. Natural, safe for the environ-
ment, and contains no CFC’s.
G5563—SLIPIT® 12 oz Spray
Used on cast iron table surfaces and other
unpainted metal surfaces to reduce sliding friction
and hangups. This product also reduces rust and
prevents resin build-up.
Figure 77. G5562 & G5563 SLIPIT.
Figure 75. G7895 Citrus Degreaser.
G2871—Boeshield® T-9 12 oz Spray
G1955—OxiSolv® Blade & Bit Cleaner
Used to clean the gummy pitch and residue
from saw blades and router bits, this high qual-
ity cleaner will make blades and bits last longer
while improving cutting action.
G2870—Boeshield® T-9 4 oz Spray
This ozone friendly protective spray penetrates
deep and really holds up against corrosive envi-
ronments. Lubricates metals for months and is
safe for use on most paints, plastics, and vinyls.
Figure 76. G1955 OxiSolv®.
Figure 78. Boeshield® T-9 spray.
-43-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
G7984—Face Shield
H3388—14" Carbide Tipped Saw Blade, 80T
H3389—14" Carbide Tipped Saw Blade, 100T
These blades are designed especially for slid-
ing table saws and manufactured for heavy-duty
use.
H1298—Dust Sealed Safety Glasses
H1300—UV Blocking, Clear Safety Glasses
H2347—Uvex® Spitfire Safety Glasses
H0736—Shop Fox® Safety Glasses
Safety Glasses are essential to every shop. If
you already have a pair, buy extras for visitors
or employees. You can't be too careful when it
comes to shop safety!
H1300
H1298
H0736
G7984
Figure 81. Carbide-tipped saw blade.
H4935—Scoring Blade Set
H2347
The scoring blade set consists of an inner and
outer blade and four internal shims. Two shims
are 0.008" thick and two are 0.004". The shims
are provided so the scoring blade set can match
the kerf thickness of the main blade.
Figure 79. Our most popular safety glasses.
H2499—Small Half-Mask Respirator
H3631—Medium Half-Mask Respirator
H3632—Large Half-Mask Respirator
H3635—Disposable Cartridge Filter Pair P100
Wood dust is now considered a known carcino-
gen and has been linked to nasal cancer and
severe respiratory illnesses. If you work around
dust everyday, a half-mask respirator can be a
lifesaver. Also compatible with safety glasses!
Figure 82. H4935 Scoring Blade Set.
Figure 80. Half-mask respirator and disposable
cartridge filters.
-44-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
H3308—SHOP FOX® Push Stick
H3771—Blade Loc®
This simple tool secures the blade during blade
changes, keeping your hands safe and your
expensive blade from being damaged.
Measuring 131⁄2" overall, this push stick allows the
operator to keep their hands at a safe distance
away from the blade or cutter.
Figure 83. H3308 SHOP FOX® Push Stick.
Figure 85. H3771 Blade Loc®.
G3445—Precision Saw Tool
G7581—Superbar™
This high impact plastic Saw Aid™ quickly mea-
sures blade height and angle and can also serve
as a solid push stick. Includes a graduated ruler
guide and center finder.
G7582—Master Plate
The miter slot mounted Superbar™ will align, tune
and calibrate your tablesaw to within ±0.001 in
just minutes. Replace your tablesaw blade when
calibrating the double disk ground Master Plate
for a precision measurement, with no runout!
Figure 84. G3445 Precision Saw Tool.
Figure 86. Superbar™ and Master Plate.
-45-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: MAINTENANCE
Cleaning
Always disconnect power
to the machine before
performing maintenance.
Failure to do this may
result in serious person-
Cleaning the Model G0451 is relatively easy.
Vacuum excess wood chips and sawdust, and
wipe off the remaining dust with a dry cloth. Use
compressed air to blow dust from between the
two sections of the sliding table. If any resin has
built up, use a resin dissolving cleaner to remove
it. Treat all unpainted cast iron and steel with a
al injury.
Schedule
non-staining lubricant after cleaning.
For optimum performance from your machine,
follow this maintenance schedule and refer to any
specific instructions given in this section.
Unpainted Cast Iron
Daily Check:
•
•
•
•
Loose mounting bolts.
Worn or damaged saw blade.
Worn or damaged switches or wires.
Any other unsafe condition.
Protect the unpainted cast iron surfaces on the
table by wiping the table clean after every use—
this ensures moisture from wood dust does not
remain on bare metal surfaces.
Weekly Maintenance:
•
•
•
•
•
Clean sliding table surface and grooves.
Clean the cast iron saw table.
Clean the sliding table roller guideways.
Clean the rip fence and sliding grooves.
Clean the rip fence bracket.
Keep tables rust-free with regular applications of
products like G96® Gun Treatment, SLIPIT®, or
Boeshield® T-9 (see Section 5: Accessories on
Page 43 for more details).
Monthly Check:
•
Clean/vacuum dust buildup from inside cabi-
net and off motor.
•
V-belt tension, damage, or wear.
Note—To ensure optimum power transmission
from the motor to the blades, the V-belts must be
in good condition (free from cracks, fraying and
wear) and operate under proper tension.
-46-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Scoring blade worm gears. Lubricate with
Lubrication
an automotive wheel bearing grease.
Blade Height
Slide
The bearings are sealed and pre-lubricated and
require no lubrication during their usable life.
However, your saw components will operate
at their best if the bearing surfaces are kept
clean—this is especially important for the trun-
nion bearings.
Lubricate the areas indicated below every 6-12
months, depending on frequency of use.
Blade Height
Linkage
1. Blade angling trunnions. These should be
lubricated with 6 or 7 drops of light machine
oil (see Figure 87).
Scoring Blade
Worm Gears
Blade Tilt
Worm Gear
Blade Angling
Trunnion
Figure 89. Gear lubrication.
4. Blade height linkage. Lubricate with an
Figure 87. Blade angling trunnions.
automotive wheel bearing grease.
2. Sliding table ways. Spray or wipe on a light
machine oil such as WD-40® the entire length
of the steel rods (see Figure 88).
5. Blade height bearing (Hidden behind the
motor in Figure 89). Lubricate with an auto-
motive wheel bearing grease in a grease
gun.
6. Blade tilt worm gear. Lubricate with an
automotive wheel bearing grease.
7. Blade height slide. Lubricate with an auto-
motive wheel bearing grease.
Figure 88. Sliding table ways.
-47-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Log
Maintenance Performed
Date
Approximate Hours Of Use
-48-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7: SERVICE
Replacing Belts
Always
disconnect
power to the machine
before performing ser-
vice adjustments. Failure
to do this may result in
serious personal injury.
To change the V-belt on the main motor:
1. Disconnect the saw from the power
source!
2. Move the blade tilt to 0˚ (blade 90˚ to table),
and raise the main blade and scoring blade
set up as far as they will go.
About Service
3. Open the motor cabinet door.
This section is designed to help the operator with
adjustments that were made at the factory and
that might also need to be made during the life of
the machine.
4. Loosen the tension bolt (Figure 90) and
pivot the motor up to remove the V-belts.
Note—You may need to use a hydraulic
bottle jack to lift the motor.
This section is provided for your convenience—
it is not a substitute for the Grizzly Service
Department. If any adjustments arise that are not
described in this manual, then feel free to call the
Grizzly Service Department at (570) 546-9663.
Similarly, if you are unsure of how to perform
any procedure in this section, the Grizzly Service
Department will be happy to guide you through
the procedures or help in any other way.
Figure 90. V-belt tension bolt.
5. Remove the old V-belts and replace them
with new belts. Note—Always replace all of
the belts as a matched set.
6. Tighten the tension bolt until the belts deflect
between a 1⁄4" and a 1⁄2" when pressed firmly
in the center of each V-belt.
7. Close and secure the motor cabinet door.
-49-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
To change the belt on the scoring blade
motor:
2. Move the blade tilt to 90˚ according to the
gauge, and raise the main blade as far as it
will go.
1. Disconnect the saw from the power
source!
3. Place a machinist's square between the
teeth on the blade and on the table surface
and inspect for gaps between the blade and
the square.
2. Move the blade tilt to 0˚ (blade 90˚ to table),
and raise the main blade and scoring blade
set up as far as they will go.
4. If a gap exists at either the top or bottom
of the square, loosen the 90˚ tilt stop bolt
shown in Figure 92.
3. Open the motor cabinet door.
4. Push the scoring blade motor and remove
the flat belt.
90˚ Tilt
Stop Bolt
5. Place the flat belt on the scoring blade arbor
as shown in Figure 91, lift the scoring motor,
and slide the flat belt over the scoring motor
pulley.
Scoring
Blade
Arbor
45˚ Tilt Stop Bolt
(Hidden behind
the shaft)
Flat
Belt
Figure 92. Blade tilt stop bolts.
Scoring
Motor
5. Turn the handwheel until the blade and
square are flush from top to bottom.
6. Snug the adjustment screw against the under-
side of the table and tighten the lock nut.
Figure 91. Replacing the scoring motor belt.
6. Close and secure the motor cabinet door.
7. Recheck the blade with the square to ensure
the screw has not been over-tightened.
8. Adjust the blade angle until you hit the 45°
positive stop. Check the bevel with an adjust-
able square set to 45°.
Blade Tilt
9. If variations exist, adjust the 45˚ tilt stop
bolt (Figure 92) until the blade and square
match.
The blade tilt is calibrated at the factory, but can
be adjusted if it changes during the life of the
machine.
10. Tighten the lock nut and recheck the bevel by
adjusting the blade back to 90°, then back to
45°.
To calibrate the blade tilt:
1. Disconnect the saw from the power
source!
-50-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Rotate the blade 180° and slide the table
Sliding Table Parallel
Adjustment
with the measuring device to position B.
6. Measure the difference between the two
positions (use the feeler gauge if using the
adjustable square). Make note of the differ-
ence between the two measurements on a
piece of paper.
The table is calibrated at the factory, but can
be adjusted if it changes during the life of the
machine.
—If the gap is the same on both sides, then
the sliding table is already parallel with the
main blade.
Besides the tools included with the saw, this
procedure requires you to have a felt tip pen, an
adjustable square and a set of feeler gauges, or
a dial indicator. Note—Using a dial indicator will
provide much more accurate results.
—If the gap on one side is different than the
other, then continue with Step 7.
To adjust the sliding table parallel with the
main blade:
7. Tilt the blade to 45° and repeat Steps 4-6.
—If the difference was less than 0.004" when
the blade was positioned at 90° and 45°,
then the blade parallelism is correct.
1. Disconnect the saw from the power
source!
2. Move the blade tilt to 0˚ (blade 90˚ to table),
and raise the main blade and scoring blade
set up as far as they will go.
—If the difference was greater than 0.004"
when the blade was positioned at 90° or
45°, then the trunnion assembly below the
table needs to be adjusted. Continue with
the next step.
3. Make a mark near the edge of the blade with
a felt tip pen. This will allow you to take your
measurements from the exact same place on
the blade.
8. Open the cover plates under each end of the
table as shown in Figure 94, and loosen the
table mounting bolts.
4. Using an adjustable square or a dial indica-
tor, measure the distance (A) between the
miter slot and the front of the blade as shown
in Figure 93.
Access
Plate
Blade
Table
Figure 94. Table mounting bolt access plate.
Miter Slot
Figure 93. Measuring gap between the table
and the blade.
-51-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Use the crosscut fence to cut 1⁄2" off of each
side of the test piece, then cut side 1 again
(make five cuts total).
9. Slowly make the adjustments to the parallel-
ism adjustment bolts (Figure 95) on the end
that is closer to the blade.
4. Measure the test piece diagonally from cor-
ner-to-corner as shown in Figure 96.
1
— If both measurements are not within ⁄16",
then the crosscut fence needs to be
adjusted. Proceed to Step 6.
— If both measurements are within 1⁄16" then
you are finished with this procedure.
Figure 95. Table parallelism adjustment bolts.
10. Repeat Steps 4-9 until the gap between the
blade and the sliding table is equal.
11. Tighten the jam nuts on the parallel adjust-
ment bolts to secure them in place
12. Tighten the table mounting bolts and replace
the access plates.
Figure 96. Fence adjustment test piece.
5. Loosen the set screw shown in Figure 97
and rotate the cam to square the crosscut
fence.
Squaring Crosscut
Fence to Blade
Adjustment
Cam
Squaring the crosscut fence to the blade ensures
that cuts made with the crosscut fence will be
square. This procedure can be done by using
a piece of scrap plywood as a test piece and
making five test cuts, then adjusting the fence as
necessary.
Set Screw
To square the crosscut fence with the blade:
1. Make sure the blade is parallel with the slid-
ing table.
Figure 97. Crosscut fence adjustment cam.
6. Tighten the set screw and repeat Step 3-6.
2. Prepare the scrap test piece by cutting it to
32" x 32" and number all four sides of the test
piece.
-52-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Log
Maintenance Performed
Date
Approximate Hours Of Use
-53-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Symptom
Possible Cause
Possible Solution
Motor will not start, or it growls
on start up.
1. Emergency stop button is
depressed.
1. Rotate the button clockwise and allow it to
pop out.
2. Power supply fuse or circuit
breaker has tripped.
2. Disconnect power, and inspect circuit for
electrical shorts and repair. Replace circuit
breaker if it is old or has tripped many times.
3. Reset the thermal overload.
4. Disconnect power, and use an ohmmeter to
check switch terminals for continuity, and
replace switch if required.
3. Thermal overload has tripped.
4. Toggle switch is broken inside.
5. Start capacitor is at fault.
5. Replace start capacitor.
6. Motor fan cover is dented, stopping 6. Replace motor fan cover (and fan, if
the fan from being able to spin.
7. Motor is at fault.
damaged).
7. Replace motor.
Motor fails to develop full power 1. Power line overloaded with lights, 1. Reduce load on power line.
(output of motor decreases rap- appliances, and other motors.
idly with decrease in voltage at 2. Undersized wires or circuits too 2. Increase wire sizes or reduce length of the
motor terminals).
long.
circuit.
3. Blown capacitor.
3. Replace the capacitor.
Motor overheats.
1. Motor overloaded.
1. Reduce load on motor.
2. Air circulation through the motor 2. Clean out motor to provide normal air circula-
restricted. tion.
Motor stalls (resulting in blown 1. Short circuit in motor or loose con- 1. Repair loose or shorted terminals, or worn
fuses or tripped circuit).
nections.
insulation on motor.
2. Low voltage.
2. Correct the low voltage conditions.
3. Incorrect fuses or circuit breakers in 3. Install correct fuses or circuit breakers.
power line.
4. Motor overloaded.
4. Reduce load on motor.
Main blade runs backwards.
1. Two of the power wires are 1. Exchange wires R & T in the terminal box.
reversed.
Blade slows when cutting. Blade 1. V-belt loose.
makes a squealing noise on start- 2. V-belt worn out.
up.
1. Tighten V-belt (Page 49).
2. Replace V-belt (Page 49).
Disconnect power to the
machine when perform-
ing any troubleshooting.
Failure to do this may
result in serious person-
al injury.
-54-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Possible Cause
Possible Solution
Loud repetitious noise coming 1. Pulley setscrews or keys are missing 1. Inspect keys and setscrews. Replace
from machine.
or loose.
or tighten if necessary.
2. Motor fan is hitting the cover.
2. Adjust fan cover mounting position, tighten fan,
or shim fan cover.
3. V-belts are defective or damaged.
3. Replace V-belts (Page 49).
Vibration when running or cut- 1. Loose or damaged blade.
1. Tighten or replace blade.
2. Check/replace arbor bearings.
3. Replace belts.
ting.
2. Worn arbor bearings.
3. Worn or damaged belts.
Workpiece has burned edges, 1. Sliding table is not parallel to blade. 1. Make sliding table parallel to the
binds, or kicks back.
blade (Page 51).
2. Riving knife is not aligned with the 2. Shim the riving knife to align it with the main
blade.
blade.
3. Blade is warped.
3. Replace the blade.
Workpiece has chip out on the 1. Scoring blade height is incorrect.
1. Adjust the height of the scoring blade.
bottom edge.
2. Scoring blade is not aligned with the 2. Align the scoring blade (Page 31).
main blade.
3. Scoring blade kerf does not match 3. Adjust the scoring blade kerf (Page 31).
the main blade.
Sliding table saw does not cut 1. Sliding table is not parallel to blade. 1. Adjust the sliding table (Page 51).
square. 2. Rip fence is not parallel to blade. 2. Adjust the rip fence (Page 24).
3. Crosscut fence is not perpendicular 3. Adjust the crosscut fence perpendicular to the
to the blade.
Fence hits table top when sliding 1. Front rail is too low.
across table. 2. Rip fence roller is too low.
blade (Page 52).
1. Raise the rail (Page 24).
2. Adjust the roller (Page 24).
Blade does not reach 90˚, or blade 1. Blade stop bolts are out of adjust- 1. Adjust the stop bolts (Page 50).
does not reach 45˚. ment.
The rip fence scale is not accu- 1. The rip fence scale is out of calibra- 1. Adjust the rip fence scale (Page 31).
rate. tion or was not set up correctly.
Tilt or blade height handwheels 1. Lock knob is tight.
1. Release the lock knob.
difficult to turn.
2. Gears caked with dust.
2. Clean out dust and grease the gears.
-55-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical
REF PART #
DESCRIPTION
P04510001 Key Switch
P04510002 Power Lamp
REF PART #
DESCRIPTION
P04510004 Switch Button-OFF
P04510005 Emergency Stop Button
1
2
3
4
5
P04510003 Switch Button-ON
5
3
3
4
2
1
4
3
3
5
1
2
4
4
��������������������
���������������� ������������������
�� �� ��
�� �� ��
�� �� ��
�� �� ��
�� �� ��
�� �� ��
�� �� ��
�� �� ��
�� �� ��
�� �� ��
�� �� ��
�� �� ��
�� �� ��
�� �� ��
����
����
����
����
-56-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
6
P04510006 Terminal 3 Circuit
P04510007 Terminal 6 Circuit
P04510008 Fuse Base
12
13
14
P04510012 Over Load RA-30 (15~30A)
P04510013 Magnetic Contactor MA-09
P04510014 Over Load RA-15 for 220V
7
8
9
P04510009 Fuse 250V 10A
P04510010 Transformer
14A P04510014A Over Load RA-15 for 440V
10
11
15
P04510015 Limit Switch
P04510011 Magnetic Contactor MA-30
5
5 15 4
4
2
1
�
�
�
����
��
��
��
�����
�� �
����
����
�
�
�
3
3
��
��
6
��
�� �� �� �� �� �� �� �� �� �� �� ��
7
��
��
��
��
��
��
9
�
�
10
6
7
�
�
�
�
�
�
��������
��������
10
8
���
9
11
13
13
11
�
�
��� ��� ��� ����
Main Motor
Contactor
���� ���� ����
�
Scoring Motor
Contactor
��� ��� ��� ����
�
���� ���� ����
�
�
14
14
��
��
�
���
��
���
��
��
��
��
�
� �
�� �� ��
7
12
12
�
�
7
��
��
-57-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8: PARTS
Extension Arm Assembly
-58-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
101
102
103
104
105
106
107
108
109
110
111
112
P04510101 T-NUT M8-1.25
P04510102 STOP BRACKET
P04510103 KNOB M8-1.25 X 40
P04510104 STUD M10-1.5 X 70
P04510105 FLIP STOP
113
114
115
116
117
118
119
120
121
122
123
PLW04M
LOCK WASHER 8MM
P04510114 LOCATE PLATE
P04510115 KNOB SCREW M8-1.25 X 25
P04510116 SQUARE FENCE
P04510117 CNTR STUD M8-1.25 X 10
P04510118 FIBER WASHER 10 X 18
P04510101 T-NUT M8-1.25
PSS01M
PLN05M
SET SCREW M6-1 X 10
LOCK NUT M10-1.5
P04510108 SQUARE TUBE
P04510109 EXT. FENCE
P04510110 COVER
P04510120 ROTATE BLOCK
PS38M
PS25M
PHLP HD SCR M4-.7 X 10
PHLP HD SCR M4-.7 X 35
PHTEK7
TAP SCREW #8 X 3/8"
BTN HD SCR M8-1.25 X 16
P04510118 FIBER WASHER 10 X 18
PSBS03M
-59-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Extension Table Assembly
-60-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
P04510201 ROLLER
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
PSB115M
PLW03M
BTN HD CAP SCR M6-1 X 16
LOCK WASHER 6MM
PSS01M
SET SCREW M6-1 X 10
P04510203 ECCENTRIC
P04510220 PAD
P04510204 PLUG 80 X 40
P04510221 FENDER WASHER 12MM
P04510208 FENDER WASHER 8MM
P04510223 KNOB M8-1.25 X 50
P04510205 SUPPORT FRAME
P04510101 T-NUT M8-1.25
P04510207 KNOB M8-1.25 X 25
P04510208 FENDER WASHER 8MM
P04510209 PLUG 38 X 38
PSS01M
PSB01M
PLW03M
PW03M
SET SCREW M6-1 X 10
CAP SCREW M6-1 X 16
LOCK WASHER 6MM
FLAT WASHER 6MM
P04510210 PLUG 40 X 20
P04510211 T-BOLT M8-1.25 X 60
P04510228 SET BLOCK
PHTEK7
TAP SCREW #8 X 3/8"
P04510229 SET PIN
P04510213 COVER
P04510230 COMPRESSION SPRING
P04510231 ECCENTRIC BUSHING
P04510214 SQUARE BRACE
P04510215 T-NUT M12-1.75
P04510216 HANDLE M12-1.75 X 55
P04510101 T-NUT M8-1.25
PRP42M
ROLL PIN 3 X 20
P04510233 KNOB M8-1.25
-61-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Assembly
-62-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
PSB50M
DESCRIPTION
REF PART #
DESCRIPTION
301
302
303
304
305
306
307
308
309
310
311
312
313
314
320
321
322
323
324
325
326
327
328
329
330
331
333
334
335
336
337
338
339
340
341
CAP SCREW M5-.8 X 10
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
PSS84M
PN09M
PB33M
PN03M
PB26M
SET SCREW M10-1.5 X 35
HEX NUT M12-1.75
P04510302 FENDER WASHER 5MM
PS09M PHLP HD SCR M5-.8 X 10
HEX BOLT M12-1.75 X 50
HEX NUT M8-1.25
P04510304 POINTER
P04510305 FIX PLATE
HEX BOLT M8-1.25 X 30
PW03M
FLAT WASHER 6MM
P04510347 FENDER WASHER M14 X 30
P04510348 HEX BOLT M14-2 X 100
P04510307 STEEL WIRE
PSS05M
SET SCREW M5-.8 X 10
PN32M
HEX NUT M14-2
P04510309 INDICATOR BLOCK
PSB07M
PLN03M
CAP SCREW M6-1 X 30
LOCK NUT M6-1
PSB26M
PLW03M
CAP SCREW M6-1 X 12
LOCK WASHER 6MM
P04510352 WIRE CONNECTOR
P04510353 CORD
P04510312 SHAFT
PW03M
FLAT WASHER 6MM
P0451005
EMERGENCY STOP BUTTON
P04510314 COMPRESSION SPRING
P04510320 CONTROL PANEL FACE
P04510355 HANGER
PS40M
PHLP HD SCR M5-.8 X 16
PHTEK7
TAP SCREW #8 X 3/8"
P04510357 POWER CORD
P04510322 CORD
P04510323 CORD
P04510324 SHAFT
PSBS05M
BTN HD CAP SCR M6-1 X 20
P04510359 POWER BOX
P04510360 TERMINAL
PSS10M
PN02M
SET SCREW M10-1.5 X 20
HEX NUT M10-1.5
PS05M
PHLP HD SCR M5-.8 X 8
BTN HD CAP SCR M5-.8 X 12
PSBS06M
P04510327 ADJUST FOOT M16 X 100
PHTEK7 TAP SCREW #8 X 3/8"
P04510363 STRAIN RELIEF M20
P04510364 ARBOR WRENCH 24,19MM
P04510365 ARBOR WRENCH 24,19MM
P04510366 PUSH STICK
P04510329 TILT SCALE
P04510330 PLUG
P04510331 CORD
PLN03M
PSB02M
PSS39M
PN02M
LOCK NUT M6-1
P04510333 CORD
CAP SCREW M6-1 X 20
SET SCREW M10-1.5 X 50
HEX NUT M10-1.5
P04510334 ELECTRIC PANEL
PFN02M
PSS04M
FLANGE NUT M6-1
SET SCREW M6-1 X 12
PFS07M
FLANGE SCREW M5-.8 X 10
P04510337 MACHINE BODY
P04510338 LOCATE BLOCK
P04510372 WIRE CLIP 5/16"
P04510373 STUD M12-1.75 X 720
PSB11M
PHTEK7
PN02M
CAP SCREW M8-1.25 X 16
PN09M
PW06M
HEX NUT M12-1.75
TAP SCREW #8 X 3/8"
HEX NUT M10-1.5
FLAT WASHER 12MM
-63-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Assembly
-64-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
417
418
419
421
422
423
424
425
426
427
428
429
430
431
PW04M
PRP58M
PLW06M
PSB84M
FLAT WASHER 10MM
ROLL PIN 6 X 45
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
PLW01M
PW02M
LOCK WASHER 5MM
FLAT WASHER 5MM
LOCK WASHER 10MM
CAP SCREW M10-1.5 X 35
P04510434 FIX BLOCK
P04510208 FENDER WASHER 8MM
P04510405 LEFT TRUNNION BRACKET
P04510406 LOCATE PLATE
PLW04M
PSB31M
PW04M
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 25
FLAT WASHER 10MM
PSB26M
PW01M
PLW03M
PW03M
PLW03M
PSB04M
CAP SCREW M6-1 X 12
FLAT WASHER 8MM
LOCK WASHER 6MM
FLAT WASHER 6MM
LOCK WASHER 6MM
CAP SCREW M6-1 X 10
PLW06M
PSB84M
PSB72M
LOCK WASHER 10MM
CAP SCREW M10-1.5 X 35
CAP SCREW M10-1.5 X 30
P04510442 SEGMENT RACK
PLW04M
PN03M
LOCK WASHER 8MM
HEX NUT M8-1.25
P04510413 FIX PLATE
P04510414 DOOR SAFETY SWITCH
PB26M
HEX BOLT M8-1.25 X 30
CAP SCREW M8-1.25 X 20
PS25M
PN04M
PW05M
PHLP HD SCR M4-.7 X 35
HEX NUT M4-.7
PSB14M
P04510447 LOCATE BLOCK
FLAT WASHER 4MM
P04510448 RIGHT TRUNNION BRACKET
P04510419 STRAIN RELIEF PG11
P04510421 CAP SCREW M5-.8 X 5
PRP58M
PSB12M
PW01M
PSB07M
PLW03M
PN03M
ROLL PIN 6 X 45
CAP SCREW M8-1.25 X 40
FLAT WASHER 8MM
CAP SCREW M6-1 X 30
LOCK WASHER 6MM
HEX NUT M8-1.25
PLW01M
PW02M
LOCK WASHER 5MM
FLAT WASHER 5MM
P04510424 HINGE
PN03M
HEX NUT M8-1.25
LOCK WASHER 8MM
PLW04M
P04510455 LOCATE BLOCK
P04510427 COVER
PB28M
HEX BOLT M8-1.25 X 60
P04510428 STUD LATCH
PSS06M
PSB33M
PSS75M
SET SCREW M8-1.25 X 16
CAP SCREW M5-.8 X 12
SET SCREW M10-1.5 X 16
PSB50M
CAP SCREW M5-.8 X 10
P04510430 CATCH
PSB50M
CAP SCREW M5-.8 X 10
P04510460 CHANNEL BASE
-65-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Arbor and Dust Hood Assembly
-66-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
519
P04510501 BLADE GUARD
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
P04510208 FENDER WASHER 8MM
P04510521 BUSHING
P04510208 FENDER WASHER 8MM
PSBS07M
PN09M
BTN HD SCR M8-1.25 X 40
HEX NUT M12-1.75
P04510522 LINK PLATE
P04510523 KEY 8 X 7 X 35
P04510524 MAIN ARBOR 1"
P04510505 LOCATE PLATE
P04510506 RIVING KNIFE
P6206
BALL BEARING 6206ZZ
P04510507 SPECIAL WASHER 12MM
P04510526 MAIN HOUSING
PLW05M
PB101M
LOCK WASHER 12MM
PSS06M
SET SCREW M8-1.25 X 16
HEX BOLT M12-1.75 X 40
P04510528 BUSHING
P04510510 LOCATING PIN
P04510511 FIX BLOCK
P6206
BALL BEARING 6206ZZ
P04510530 LOCATE RING
P04510531 ARBOR PULLEY
P04510208 FENDER WASHER 8MM
PSB14M
CAP SCREW M8-1.25 X 20
P04510513 HEX NUT M16-2 LH
P04510514 ARBOR FLANGE
P04510208 FENDER WASHER 8MM
P04510516 BUSHING
PLW04M
PSB31M
PSS11M
PSBS08M
PLW06M
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 25
SET SCREW M6-1 X 16
BTN HD SCR M10-1.5 X 35
LOCK WASHER 10MM
P04510517 HOSE CLAMP 2-1/2"
PSB14M
CAP SCREW M8-1.25 X 20
-67-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Sliding Table Assembly
-68-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
P04510601 LOCATE PLATE
630
631
632
633
634
635
636
637
638
639
640
641
642
643
645
646
647
648
649
650
651
652
653
654
655
656
657
658
P04510630 BLOCK
PSB115M
BTN HD CAP SCR M6-1 X 16
P04510631 DISC-GASKET
P04510215 T-NUT M12-1.75
P04510633 PIN LOCK
P04510603 PROTECT PLATE
P04510604 T-BOLT M12-1.75 X 60
PW06M
PLW05M
PN09M
FLAT WASHER 12MM
LOCK WASHER 12MM
HEX NUT M12-1.75
PN05M
HEX NUT M16-1.5
PSB11M
CAP SCREW M8-1.25 X 16
P04510636 HANDLE
P04510608 SLIDING TABLE SET
P04510609 HANDLE M12-1.75
PLW04M
PN03M
LOCK WASHER 8MM
HEX NUT M8-1.25
PW06M
FLAT WASHER 12MM
PSB115M
BTN HD CAP SCR M6-1 X 16
P04510215 T-NUT M12-1.75
P04510640 RIGHT END PLATE
P04510612 KNOB M12-1.75 X 20
PN05M
HEX NUT M16-1.5
PW06M
FLAT WASHER 12MM
PSB115M
BTN HD CAP SCR M6-1 X 16
P04510614 EDGE SHOE PLATE
P04510215 T-NUT M12-1.75
P04510616 BALL KNOB M8-1.25
P04510617 HANDLE SHAFT
P04510618 CAM
P04510643 LOCK PLATE
P04510645 HORIZ. LOCATE PLATE
PFH02M
FLAT HD SCR M6-1 X 12
P04510647 VERTICAL LOCATE PLATE
P04510648 ADJUST LOCATE RACK
P04510619 CAM BRACKET
PB02M
HEX BOLT M6-1 X 12
PRP32M
ROLL PIN 6 X 40
P04510650 STEEL RAIL
P04510621 LOCATE BLOCK
P04510651 BOTTOM BASE
P04510652 BUMPER
PR03M
EXT RETAINING RING 12MM
P04510623 COMPRESSION SPRING
P04510624 SHAFT
P04510653 SLIDING BOTTOM
P04510654 STEEL BALL SLEEVE
P04510655 STEEL BALL 16MM
P04510656 STEEL BALL 16.2MM
PN02
HEX NUT 5/16-18
P04510626 LARGE WASHER
P04510627 SHAFT
PSB04M
CAP SCREW M6-1 X 10
P04510628 SHAFT
PSBS11M
BTN HD CAP SCR M6-1X10
P04510629 LOCK HANDLE
-69-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Assembly
-70-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
P04510701 SUPPORT BRACE
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
PSS04M
PN02M
SET SCREW M6-1 X 12
HEX NUT M10-1.5
PN03M
HEX NUT M8-1.25
PSB14M
PSB11M
PLW04M
CAP SCREW M8-1.25 X 20
CAP SCREW M8-1.25 X 16
LOCK WASHER 8MM
P04510723 SCALE
PLW06M
PSB64M
LOCK WASHER 10MM
CAP SCREW M10-1.5 X 20
P04510208 FENDER WASHER 8MM
P04510726 STUD M12-1.75 X 115
PSB61M
PLW06M
PSS04M
CAP SCREW M10-1.5 X 20
LOCK WASHER 10MM
SET SCREW M6-1 X 12
PN09M
HEX NUT M12-1.75
PSB11M
PLW04M
CAP SCREW M8-1.25 X 16
LOCK WASHER 8MM
P04510710 OUTFEED EXT. TABLE
P04510711 TABLE
P04510730 END WASHER
P04510731 ROUND RAIL
P04510732 RING STOP
P04510712 LEFT SUPPORT PLATE
P04510713 EXTENSION TABLE
PSS01M
PW04M
PW06M
PLW05M
PN09M
SET SCREW M6-1 X 10
PLW06M
PSB72M
LOCK WASHER 10MM
FLAT WASHER 10MM
FLAT WASHER 12MM
LOCK WASHER 12MM
HEX NUT M12-1.75
CAP SCREW M10-1.5 X 30
P04510716 HOSE SUPPORT PLATE
PN02M
HEX NUT M10-1.5
PSB61M
PLW06M
PW04M
CAP SCREW M10-1.5 X 20
LOCK WASHER 10MM
FLAT WASHER 10MM
P04510738 TABLE INSERT
PSB38M CAP SCREW M5-.8 X 25
-71-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Fence Assembly
-72-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
P04510801 ROTATE SHAFT
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
PSB115M
PSBS09M
PW03M
BTN HD CAP SCR M6-1 X 16
BTN HD CAP SCR M6-1 X 12
FLAT WASHER 6MM
P04510802 HANDLE M10-1.5 X 12
P04510803 RIP FENCE HOUSING
P04510804 KNOB M10-1.5 X 70
P04510821 PLATE
PN03M
HEX NUT M8-1.25
P04510822 COMPRESSION SPRING
P04510823 CAM
P04510806 LOCATE PLATE
P04510807 MICRO-ADJUST KNOB
PSB11M
PSS05M
CAP SCREW M8-1.25 X 16
SET SCREW M5-.8 X 10
PLW04M
PN03M
LOCK WASHER 8MM
HEX NUT M8-1.25
P04510826 CLAMP PLATE
P04510827 FENCE PLATE
P04510828 BEARING PAD
P04510829 ECCENTRIC SHAFT
P04510830 PLASTIC ROLLER
P04510810 LOCATE BLOCK
PLN05M LOCK NUT M10-1.5
P04510812 HANDLE M10-1.5 X 12
P04510813 CAM
P04510814 WAVE WASHER 10 X 15
PW03M
FLAT WASHER 6MM
PFS12Mýý
FLANGE SCREW M5-.8 X 12
PSB01M
CAP SCREW M6-1 X 16
P04510816 SPRING PIECE
P04510817 PIN
P04510833 STUD M8-1.25 X 110
-73-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Motor Assembly
-74-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
PN09M
DESCRIPTION
REF PART #
DESCRIPTION
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
HEX NUT M12-1.75
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
PB100M
PSB37M
HEX BOLT M14-2 X 100
CAP SCREW M6-1 X 50
P04510902 SCORING FLANGE
P04510903 SCORING BLADE 22MM
P04510904 SCORING ARBOR 22MM
P04510939 FIX PLATE
PSB60M
CAP SCREW M8-1.25 X 55
PLN04M
LOCK NUT M8-1.25
P04510941 ADJUST KNOB
P04510906 FIX PLATE
P04510907 BUSHING
P04510908 FIX PLATE
PSB01M
PLN03M
CAP SCREW M6-1 X 16
LOCK NUT M6-1
P04510944 ADJUST SHAFT
P04510945 FIX BRACKET
P04510946 SLEEVE
PSB12M
PSS01M
CAP SCREW M8-1.25 X 40
SET SCREW M6-1 X 10
P04510911 FLAT BELT 15 X 787
P04510912 SHAFT
PB45M
HEX BOLT M8-1.25 X 100
P04510948 KNOB M6-1 X 20
P04510913 COLLAR
PLN04M
PN03M
LOCK NUT M8-1.25
HEX NUT M8-1.25
PSS01M
PLW04M
PB07M
SET SCREW M6-1 X 10
LOCK WASHER 8MM
HEX BOLT M8-1.25 X 25
P04510951 FIX PLATE
P04510952 BUSHING
P04510953 LEADSCREW
P04510935 GEAR 15T
P04510955 FIX PLATE
P04510917 SHAFT
PSS01M
SET SCREW M6-1 X 10
P04510919 LOCATE PLATE
PSB130M
CAP SCREW M10-1.5 X 16
PSB29M
CAP SCREW M6-1 X 40
P04510921 MOTOR PLATE
P04510922 ARBOR PULLEY
P04510957 MOTOR PULLEY
PSS01M
PK23M
SET SCREW M6-1 X 10
KEY 5 X 5 X 25
PR09M
EXT RETAINING RING 20MM
P04510924 SCORING HOUSING
P04510960 SCORING MOTOR 1HP
P6204
BALL BEARING 6204ZZ
960-1 P04510960-1 FAN COVER
960-2 P04510960-2 MOTOR FAN
960-3 P04510960-3 MOTOR WIRING BOX
P04510926 COLLAR
PSS02M
SET SCREW M6-1 X 6
P04510928 FIX BLOCK
961
962
963
964
965
966
967
968
P04510961 SCORING MOTOR CORD
PN03M HEX NUT M8-1.25
P04510208 FENDER WASHER 8MM
PLN04M
LOCK NUT M8-1.25
P04510930 FIX PLATE
PN32M
HEX NUT M14-2
LOCK NUT M6-1
PB01M
HEX BOLT M10-1.5 X 30
LOCK WASHER 10MM
FLAT WASHER 10MM
PLN03M
PLW06M
PW04M
P04510933 ADJUST SHAFT
P04510934 FIX BLOCK
P04510935 GEAR 15T
P04510967 FIX PLATE
PN02M HEX NUT M10-1.5
PSB01M
CAP SCREW M6-1 X 16
-75-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Adjustment Assembly
-76-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1001 PSB04M
CAP SCREW M6-1 X 10
1024 P04511024 BALL BEARING UCFK205
1002 P04511002 FREE JOINT
1025 PSB11M
1026 PLW04M
1027 P0451208
1028 PR05M
1029 PSB03M
CAP SCREW M8-1.25 X 16
LOCK WASHER 8MM
1003 PSB04M
1004 PR05M
1005 PSB11M
1006 PLW04M
CAP SCREW M6-1 X 10
EXT RETAINING RING 15MM
CAP SCREW M8-1.25 X 16
LOCK WASHER 8MM
FENDER WASHER 8MM
EXT RETAINING RING 15MM
CAP SCREW M5-.8 X 8
1007 P04511007 LOCATE RING
1030 P04511030 FREE JOINT
1008 P04511008 HAND WHEEL SHAFT
1031 PSB04M
CAP SCREW M6-1 X 10
1009 PK25M
1010 P04511010 HAND WHEEL 8"
1011 PW04M FLAT WASHER 10MM
1012 P04511012 KNOB M10-1.5
KEY 7 X 7 X 20
1032 P04511032 SHAFT
1033 PSB04M
1034 PW03M
CAP SCREW M6-1 X 10
FLAT WASHER 6MM
1035 P04511035 SUPPORT PLATE
1036 P04511036 COLLAR
1013 PSB40M
1014 PLW04M
1015 P0451208
1016 PLN04M
CAP SCREW M8-1.25 X 35
LOCK WASHER 8MM
FENDER WASHER 8MM
LOCK NUT M8-1.25
1037 P04511037 THRST BEARING LFW-2015
1038 P04511038 LOCATE BLOCK
1039 P04511039 BUSHING DU2030
1017 P04511017 LONG SHAFT
1040 P51104
THRUST BEARING 51104
1018 PSB58M
1019 PLW04M
CAP SCREW M8-1.25 X 12
LOCK WASHER 8MM
1041 P04511041 WORM SHAFT
1042 PK25M
1043 PSB84M
1044 PSS01M
KEY 7 X 7 X 20
1020 P04511020 LOCATE PLATE
1021 P04511021 BEARING SET
1022 P04511022 GEAR 30T
CAP SCREW M10-1.5 X 35
SET SCREW M6-1 X 10
1045 P04511045 BUSHING DU1515
1023 PSS01M
SET SCREW M6-1 X 10
-77-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Swing Arm Assembly
-78-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1101 P04511101 NYLON WASHER M10 X 25
1102 P04511102 SUPPORT SHAFT
1116 PSS19M
SET SCREW M8-1.25 X 30
1117 P04511117 ROLLER
1103 PN05M
HEX NUT M16-1.5
1118 P6202
1119 PSS19M
1120 PR21M
BALL BEARING 6202ZZ
1104 P04511104 PLUG 100 X 50
SET SCREW M8-1.25 X 30
INT RETAINING RING 35MM
1105 PB26M
HEX BOLT M8-1.25 X 30
1106 P04511106 MAGNETIC BRACKET
1107 P04511107 SLIDING TUBE
1121 P04511121 SWING ARM
1122 P51102
1123 PB82M
1124 PW01M
1125 PLN04M
1126 P6202
THRUST BEARING 51102
1108 PB26M
1109 PN03M
1110 PHTEK7
HEX BOLT M8-1.25 X 30
HEX NUT M8-1.25
HEX BOLT M8-1.25 X 80
FLAT WASHER 8MM
LOCK NUT M8-1.25
TAP SCREW #8 X 3/8"
1111 P04511111 COVER
BALL BEARING 6202ZZ
1112 PW01M
FLAT WASHER 8MM
1127 P04511127 BRUSH
1113 P04511113 ADJUST SHAFT
1128 PW03M
1129 PSB02M
FLAT WASHER 6MM
CAP SCREW M6-1 X 20
1114 PR05M
1115 PN03M
EXT RETAINING RING 15MM
HEX NUT M8-1.25
-79-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Motor Assembly
-80-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1201 P04511201 DUST PORT
1226
1227
1228
PLW06M
PW04M
LOCK WASHER 10MM
FLAT WASHER 10MM
MAIN MOTOR 10HP
1202 PSB52M
1203 PLW04M
CAP SCREW M8-1.25 X 10
LOCK WASHER 8MM
P04511228
1204 P04511204 ROTATE PLATE
1228-1 P04511228-1 FAN COVER
1228-2 P04511228-2 MOTOR FAN
1228-3 P04511228-3 MOTOR WIRING BOX
1205 PSS01M
SET SCREW M6-1 X 10
1206 P04511206 SHAFT
1207 P04511207 LOCATE PLATE
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
PN02M
HEX NUT M10-1.5
1208 PN09M
1209 PB33M
1210 PN02M
HEX NUT M12-1.75
HEX BOLT M12-1.75 X 50
HEX NUT M10-1.5
P04511230
P04511231
P04511232
P51200
MAIN MOTOR CORD
ADJUST BLOCK
ELEV SCREW M16-2 X 335
THRUST BEARING 51200
BALL BEARING 6200ZZ
EXT RETAINING RING 10MM
FIX BLOCK
1211 P04511211 SUPPORT PLATE
1212 P04511212 BUSHING
P6200
1213 PLW06M
1214 PSB134M
LOCK WASHER 10MM
PR01M
CAP SCREW M10-1.5 X 65
P04511236
PLW06M
PSB70M
PVM25
1215 P04511215 BUSHING
1216 P04511216 GIB PLATE
LOCK WASHER 10MM
CAP SCREW M10-1.5 X 45
V-BELT M25
1217 PSBS10M
BTN HD SCR M10-1.5 X 25
1218 P04511218 LOCATE PLATE
P04511240
PSS01M
P04511242
PB01M
MAIN MOTOR PULLEY
SET SCREW M6-1 X 10
KEY 8 X 7 X 50
1219 PLW04M
1220 PSB11M
1221 PSB130M
1222 PLW06M
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 16
CAP SCREW M10-1.5 X 16
LOCK WASHER 10MM
HEX BOLT M10-1.5 X 30
LOCK WASHER 10MM
FLAT WASHER 10MM
FIX PLATE
PLW06M
PW04M
1223 P04511223 COLLAR
1224 P04511224 MAIN MOTOR PLATE
P04511246
PN02M
1225 PB31M
HEX BOLT M10-1.5 X 40
HEX NUT M10-1.5
-81-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the
carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
-82-
G0451 14" Sliding Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name_____________________________________________________________________________
Street_____________________________________________________________________________
City _______________________ State_________________________ Zip _____________________
Phone #____________________ Email ________________________ Invoice #_________________
Model # ____________________ Order #_______________________ Serial #__________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
____ Advertisement
____ Card Deck
____ Friend
____ Website
____ Catalog
____ Other:
2. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Practical Homeowner
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Today’s Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Modeltec
____ Woodwork
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Rifle
____ Shop Notes
____ Old House Journal
____ Shotgun News
3. What is your annual household income?
____ $20,000-$29,000
____ $30,000-$39,000
____ $40,000-$49,000
____ $70,000+
____ $50,000-$59,000
____ $60,000-$69,000
4. What is your age group?
____ 20-29
____ 30-39
____ 60-69
____ 40-49
____ 70+
____ 50-59
5. How long have you been a woodworker/metalworker?
____ 0-2 Years ____ 2-8 Years
____ 8-20 Years
____ 6-9
____20+ Years
____10+
6. How many of your machines or tools are Grizzly?
____ 0-2 ____ 3-5
7. Do you think your machine represents a good value?
8. Would you recommend Grizzly Industrial to a friend?
_____Yes
_____Yes
_____No
_____No
9. Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times. _____Yes _____No
10. Comments:_____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
�����������������������������������������������������������������������
�������������������������������������
������������������������������������
�����������������
��������������������������������
���������������������������������
����
�����������������
����
������������������
Download from Www.Somanuals.com. All Manuals Search And Download.
|