Instructions–Parts List
SEVERE-DUTY, UHMWPE/PTFE PACKED
308118N
Stainless Steel Pumps
EN
55 gallon (200 liter) drum size, with bung adapter.
For transfer and supply of solventborne and waterborne finishing materials.
For professional use only.
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
See page 2 for table of contents.
Model 224348, Series C
10:1 Ratio Presidentr Pump
0359
II 1/2 G T2
ITS03ATEX11228
Model 256713, Series A
10:1 Ratio Presidentr Pump (1.5 in. Female Inlet)
1800 psi (12.4 MPa, 124 bar) Maximum Fluid Working Pressure
180 psi (1.25 MPa, 12.5 bar) Maximum Air Inlet Pressure
Model 224350, Series C
5:1 Ratio Monarkr Pump
0359
II 1/2 G T2
ITS03ATEX11228
Model 256714, Series A
5:1 Ratio Monarkr Pump (1.5 in. Female Inlet)
900 psi (6.3 MPa, 63 bar) Maximum Fluid Working Pressure
180 psi (1.25 MPa, 12.5 bar) Maximum Air Inlet Pressure
0200A
MODEL 224348 SHOWN
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
SKIN INJECTION HAZARD
Spray from the gun/valve, hose leaks, or ruptured components can inject fluid into your body and
cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the
skin can also cause serious injury.
D
F
l
u
i
d
i
n
j
e
c
t
e
d
i
n
t
o
t
h
e
s
k
i
n
m
i
g
h
t
l
o
o
k
l
i
k
e
j
u
s
t
a
c
u
t
,
b
u
t
i
t
i
s
a
s
e
r
i
o
u
s
i
n
j
u
r
y
.
G
e
t
i
m
m
e
d
i
a
t
e
s
u
r
g
i
-
cal treatment.
D Do not point the gun/valve at anyone or at any part of the body.
D Do not put your hand or fingers over the spray tip/nozzle.
D Do not stop or deflect leaks with your hand, body, glove or rag.
D Do not “blow back” fluid; this is not an air spray system.
D Always have the tip guard and the trigger guard on the gun when spraying.
D Check the gun diffuser operation weekly. Refer to the gun manual.
D Be sure the gun/valve trigger safety operates before spraying/dispensing.
D Lock the gun/valve trigger safety when you stop spraying/dispensing.
D Follow the Pressure Relief Procedure on page 9 whenever you: are instructed to relieve pres-
sure; stop spraying/dispensing; clean, check, or service the equipment; and install or clean the
spray tip/nozzle.
D
T
i
g
h
t
e
n
a
l
l
f
l
u
i
d
c
o
n
n
e
c
t
i
o
n
s
b
e
f
o
r
e
o
p
e
r
a
t
i
n
g
t
h
e
e
q
u
i
p
m
e
n
t
.
D
C
h
e
c
k
t
h
e
h
o
s
e
s
,
t
u
b
e
s
,
a
n
d
c
o
u
p
l
i
n
g
s
d
a
i
l
y
.
R
e
p
l
a
c
e
w
o
r
n
,
d
a
m
a
g
e
d
,
o
r
l
o
o
s
e
p
a
r
t
s
i
m
m
e
d
i
a
t
e
l
y
.
Permanently coupled hoses cannot be repaired; replace the entire hose.
D
U
s
e
o
n
l
y
G
r
a
c
o
a
p
p
r
o
v
e
d
h
o
s
e
s
.
D
o
n
o
t
r
e
m
o
v
e
a
n
y
s
p
r
i
n
g
g
u
a
r
d
t
h
a
t
i
s
u
s
e
d
t
o
h
e
l
p
p
r
o
t
e
c
t
t
h
e
hose from rupture caused by kinks or bends near the couplings.
MOVING PARTS HAZARD
Moving parts, such as the air motor piston, can pinch or amputate your fingers.
D
K
e
e
p
c
l
e
a
r
o
f
a
l
l
m
o
v
i
n
g
p
a
r
t
s
w
h
e
n
s
t
a
r
t
i
n
g
o
r
o
p
e
r
a
t
i
n
g
t
h
e
p
u
m
p
.
D
B
e
f
o
r
e
s
e
r
v
i
c
i
n
g
t
h
e
e
q
u
i
p
m
e
n
t
,
f
o
l
l
o
w
t
h
e
P
r
e
s
s
u
r
e
R
e
l
i
e
f
P
r
o
c
e
d
u
r
e
o
n
p
a
g
e
9
t
o
p
r
e
v
e
n
t
t
h
e
equipment from starting unexpectedly.
308118
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
D
G
r
o
u
n
d
t
h
e
e
q
u
i
p
m
e
n
t
a
n
d
t
h
e
o
b
j
e
c
t
b
e
i
n
g
s
p
r
a
y
e
d
.
R
e
f
e
r
t
o
G
r
o
u
n
d
i
n
g
o
n
p
a
g
e
5
.
D If there is any static sparking or you feel an electric shock while using this equipment, stop spray-
ing/dispensing immediately. Do not use the equipment until you identify and correct the problem.
D
P
r
o
v
i
d
e
f
r
e
s
h
a
i
r
v
e
n
t
i
l
a
t
i
o
n
t
o
a
v
o
i
d
t
h
e
b
u
i
l
d
u
p
o
f
f
l
a
m
m
a
b
l
e
f
u
m
e
s
f
r
o
m
s
o
l
v
e
n
t
s
o
r
t
h
e
f
l
u
i
d
being sprayed/dispensed.
D Keep the spray/dispense area free of debris, including solvent, rags, and gasoline.
D Electrically disconnect all equipment in the spray/dispense area.
D Extinguish all open flames or pilot lights in the spray/dispense area.
D Do not smoke in the spray/dispense area.
D
D
o
n
o
t
t
u
r
n
o
n
o
r
o
f
f
a
n
y
l
i
g
h
t
s
w
i
t
c
h
i
n
t
h
e
s
p
r
a
y
/
d
i
s
p
e
n
s
e
a
r
e
a
w
h
i
l
e
o
p
e
r
a
t
i
n
g
o
r
i
f
f
u
m
e
s
a
r
e
present.
D
D
o
n
o
t
o
p
e
r
a
t
e
a
g
a
s
o
l
i
n
e
e
n
g
i
n
e
i
n
t
h
e
s
p
r
a
y
/
d
i
s
p
e
n
s
e
a
r
e
a
.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D
K
n
o
w
t
h
e
s
p
e
c
i
f
i
c
h
a
z
a
r
d
s
o
f
t
h
e
f
l
u
i
d
y
o
u
a
r
e
u
s
i
n
g
.
D
S
t
o
r
e
h
a
z
a
r
d
o
u
s
f
l
u
i
d
i
n
a
n
a
p
p
r
o
v
e
d
c
o
n
t
a
i
n
e
r
.
D
i
s
p
o
s
e
o
f
h
a
z
a
r
d
o
u
s
f
l
u
i
d
a
c
c
o
r
d
i
n
g
t
o
a
l
l
l
o
c
a
l
,
state and national guidelines.
D
A
l
w
a
y
s
w
e
a
r
p
r
o
t
e
c
t
i
v
e
e
y
e
w
e
a
r
,
g
l
o
v
e
s
,
c
l
o
t
h
i
n
g
a
n
d
r
e
s
p
i
r
a
t
o
r
a
s
r
e
c
o
m
m
e
n
d
e
d
b
y
t
h
e
f
l
u
i
d
a
n
d
solvent manufacturer.
4
308118
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
4. Spray gun: grounding is obtained through connec-
Grounding
tion to a properly grounded fluid hose and pump.
5. Object being sprayed: according to your local
WARNING
code.
FIRE AND EXPLOSION HAZARD
Before operating the pump, ground the
system as explained below. Also read
the section FIRE AND EXPLOSION
HAZARD on page 4.
6. Fluid supply container: according to your local
code.
7. All solvent pails used when flushing, according to
your local code. Use only metal pails, which are
conductive, placed on a grounded surface. Do not
place the pail on a non-conductive surface, such
as paper or cardboard, which interrupts the
grounding continuity.
To reduce the risk of static sparking, ground the pump.
Check your local electrical code for detailed grounding
instructions for your area and type of equipment. Be
sure to ground all of this dispensing equipment.
8. To maintain grounding continuity when flushing or
relieving pressure, always hold a metal part of the
spray gun firmly to the side of a grounded metal
pail, then trigger the spray gun.
1. Pump: loosen the grounding lug locknut (W) and
2
washer (X). Insert one end of a 1.5 mm (12 ga)
minimum ground wire (Y) into the slot in lug (Z)
and tighten the locknut securely. See Fig. 1. Con-
nect the other end of the ground wire to a true
earth ground. Order Part No. 237569 Ground Wire
and Clamp.
Z
Y
2. Air and fluid hoses: use only electrically conductive
hoses with a maximum of 500 ft (150 m) combined
hose length to ensure grounding continuity.
X
3. Air compressor: follow manufacturer’s recommen-
0720
W
Fig. 1
dation.
308118
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
H
Typical Installation
Y
A
B
E
F
G
N
C
D
M
K
J
L
1/2 in. (13 mm)
0808A
KEY
A
B
C
D
E
F
G
H
J
K
L
Pump
Pump Runaway Valve
Air Line Lubricator
Bleed–Type Master Air Valve (required, for pump)
Pump Air Regulator
Air Line Filter
Bleed–Type Master Air Valve (for accessories)
Air Supply Hose
Fluid Drain Valve (required)
Fluid Filter
Fluid Supply Hose
M
N
Y
Spray Gun
Pump Bung Adapter
Ground Wire (required; see page 5
for installation instructions)
6
308118
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
NOTE: Reference numbers and letters in parentheses
in the text refer to the callouts in the figures and the
Parts Drawing.
Connect a electrically conductive fluid hose (L) to the
fluid filter (K), if used, or directly to the pump’s fluid
outlet.
NOTE: Contact you Graco distributor for available
Graco accessories. If you supply your own accesso-
ries, be sure they are adequately sized and pressure-
rated to meet the system’s requirements.
Use a electrically conductive 1/2 in. ID (minimum) air
hose (H) to supply air to the pump.
Air Line Accessories
The Typical Installation shown on page 6 is only a
guide for selecting and installing system components
and accessories. Contact your Graco distributor for
assistance in designing a system to suit your particular
needs.
Install the following accessories in the order shown in
the Typical Installation, using adapters as necessary.
D
A
n
a
i
r
l
i
n
e
l
u
b
r
i
c
a
t
o
r
(
C
)
p
r
o
v
i
d
e
s
a
u
t
o
m
a
t
i
c
a
i
r
motor lubrication.
System Accessories
D A bleed-type master air valve (D) is required in
your system to relieve air trapped between it and
the air motor when the valve is closed (see the
WARNING at left). Be sure the bleed valve is easily
accessible from the pump, and is located down-
stream from the air regulator.
Refer to the Typical Installation on page 6.
WARNING
A bleed-type master air valve (D) and a fluid drain
valve (J) are required in your system. These acces-
sories help reduce the risk of serious injury includ-
ing fluid injection, splashing in the eyes or on the
skin, and injury from moving parts if you are adjust-
ing or repairing the pump.
D A pump runaway valve (B) senses when the
pump is running too fast and automatically shuts off
the air to the motor. A pump which runs too fast can
be seriously damaged.
The bleed-type master air valve relieves air trapped
between this valve and the pump after the air is
shut off. Trapped air can cause the pump to cycle
unexpectedly. Locate the valve close to the pump.
D An air regulator (E) controls pump speed and
outlet pressure by adjusting the air pressure to the
pump. Locate the regulator close to the pump, but
upstream from the bleed-type master air valve.
The fluid drain valve assists in relieving fluid pres-
sure in the displacement pump, hose, and gun.
Triggering the gun to relieve pressure may not be
sufficient.
D
A
n
a
i
r
l
i
n
e
f
i
l
t
e
r
(
F
)
r
e
m
o
v
e
s
h
a
r
m
f
u
l
d
i
r
t
a
n
d
moisture from the compressed air supply.
D A second bleed-type master air valve (G) iso-
lates the air line accessories for servicing. Locate
upstream from all other air line accessories.
Mounting Accessories
Mount the pump (A) to suit the type of installation
planned. The pump dimensions and mounting hole
layout are shown on page 26.
Fluid Line Accessories
Install the following accessories in the positions shown
in the Typical Installation, using adapters as neces-
sary:
The pump is supplied with a bung adapter. To mount
the pump, loosen the bung adapter screw and slide the
adapter off the pump. Screw the bung adapter secure-
ly into the bung hole on the cover of the supply drum.
Carefully lower the pump through the bung adapter
and into the drum until it rests on the bottom, then pull
it back up 1/2 in. (13 mm). Tighten the bung adapter
screw to hold the pump in this position. Open the
drum’s vent plug to prevent a vacuum from forming in
the drum.
D A fluid drain valve (J) is required in your system
to relieve fluid pressure in the hose and gun (see
the WARNING at left). Install the drain valve point-
ing down, but so the handle points up when
opened.
D
A
f
l
u
i
d
f
i
l
t
e
r
(
K
)
f
i
l
t
e
r
s
h
a
r
m
f
u
l
p
a
r
t
i
c
l
e
s
f
r
o
m
t
h
e
Air and Fluid Hoses
fluid.
Be sure all air and fluid hoses are properly sized and
pressure-rated for your system. Use only electrically
conductive air and fluid hoses. Fluid hoses must have
spring guards on both ends.
D A spray gun (M) dispenses the fluid. The gun
shown in the Typical Installation is an airless
spray gun.
308118
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
8
308118
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Pressure Relief Procedure
WARNING
WARNING
Moving parts can pinch or amputate your fingers or
other body parts. When air is supplied to the motor,
the air motor piston (located behind the air motor
plates) moves. See Fig. 2. Therefore, never oper-
ate the pump with the air motor plates removed.
SKIN INJECTION HAZARD
Fluid under high pressure can be in-
jected through the skin and cause
serious injury. To reduce the risk of an
injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
Flush the Pump Before Using
The pump is tested with lightweight motor oil, which is
left in to protect the pump parts. If the fluid you are
using may be contaminated by the oil, flush it out with
a compatible solvent before using the pump. If the
pump is being used to supply a circulating system,
allow the solvent to circulate until the pump is thor-
oughly flushed.
D are instructed to relieve the pressure,
D stop spraying,
D check or service any of the system equipment,
D or install or clean the spray tips.
1. Lock the spray gun trigger safety.
2. Shut off the air to the pump.
WARNING
3. Close the bleed-type master air valve (required in
your system).
FIRE AND EXPLOSION HAZARD
For your safety, read the section FIRE
AND EXPLOSION HAZARD on page 4
before flushing and follow all the recom-
mendations given there.
4. Unlock the gun trigger safety.
5. Hold a metal part of the gun firmly to the side of a
grounded metal pail, and trigger the gun to relieve
pressure.
6. Lock the spray gun trigger safety.
7. Open the drain valve (required in your system),
having a container ready to catch the drainage.
8. Leave the drain valve open until you are ready to
spray again.
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above, very slowly loosen the
tip guard retaining nut or hose end coupling and relieve
pressure gradually, then loosen completely. Now clear
the tip or hose.
308118
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Starting and Adjusting the Pump
WARNING
To reduce the risk of overpressurizing your system,
which could result in component rupture and cause
serious injury, never exceed the Maximum Incom-
ing Air Pressure given on your pump or in the
Technical Data on pages 22 and 24.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 9.
Keep the packing nut/wet-cup (14) filled with Graco
Throat Seal Liquid (TSL) or compatible solvent, to help
prolong the packing life. Adjust the packing nut weekly
so it is just tight enough to prevent leakage; do not
overtighten. See Fig. 2. Always relieve the pressure
before adjusting the packing nut.
See the Typical Installation on page 6. Be sure the
air regulator (E) and bleed-type master air valve (D)
are closed. Do not install the spray tip yet.
Mount the pump on the supply drum. On bung-style
drums, open the vent plug to prevent a vacuum from
forming in the drum. Hold a metal part of the spray gun
(M) firmly to the side of a grounded metal pail and hold
the trigger open. Then open the pump’s bleed-type
master air valve (D). Now slowly open the air regulator
until the pump starts, about 40 psi (280 kPa, 2.8 bar).
Never allow the pump to run dry of the fluid being
pumped. A dry pump will quickly accelerate to a high
speed, possibly damaging itself. A pump runaway
valve (B), which shuts off the air supply to the pump if
the pump accelerates beyond the pre-set speed, is
available. If your pump accelerates quickly, or is run-
ning too fast, stop it immediately and check the fluid
supply. If the supply container is empty and air has
been pumped into the lines, refill the container and
prime the pump and the lines with fluid, or flush and
leave it filled with a compatible solvent. Be sure to
eliminate all air from the fluid system.
Cycle the pump slowly until the air is pushed out and
the pump and hoses are fully primed. Release the
spray gun trigger and engage the safety latch. The
pump should stall against pressure when the trigger is
released.
Relieve the pressure, then install the spray tip in the
gun.
Shutdown and Care of the Pump
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 9.
With the pump and lines primed, and with adequate air
pressure and volume supplied, the pump will start and
stop as the spray gun is opened and closed. In a
circulating system, the pump will run continuously and
will speed up or slow down as supply demands until
the air supply is shut off.
For overnight shutdown, relieve the pressure. Always
stop the pump at the bottom of the stroke to prevent
the fluid from drying on the exposed displacement rod
and damaging the throat packings.
Use an adequately sized air regulator (E) to control the
pump speed and the fluid pressure. Always use the
lowest air pressure necessary to get the desired
results. Higher pressures waste fluid and cause pre-
mature wear of the packings and spray tip.
Always flush the pump before the fluid dries on the
displacement rod. Relieve the pressure after flushing.
10 308118
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
AIR MOTOR PLATE
14
0200A
Fig. 2
308118
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
12 308118
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before servicing this equipment always make sure to
WARNING
relieve the pressure.
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 9.
Check all possible problems and solutions before
disassembling the pump.
Problem
Cause
Solution
Restricted line or inadequate air sup- Clear; Increase air supply.
ply
Pump fails to operate
Insufficient air pressure; closed or
clogged air valves, etc.
Open, clean.
Exhausted fluid supply
Refill; purge all air from pump and
fluid lines.
Damaged air valving mechanism;
stalling
Service air motor (see manual
306982 or 307043).
Dried fluid seizure of displacement
rod (1)
Clean, check or replace throat pack-
ings (3, 25); always stop the pump at
the bottom of its stroke and keep the
wet-cup filled with compatible solvent.
Restricted line or inadequate air sup- Clear; increase air supply.
ply
Pump operates, but output low on
both strokes
Insufficient air pressure; closed or
clogged air valves, etc.
Open, clean.
Exhausted fluid supply
Refill; purge all air from pump and
fluid lines.
Clogged fluid line, valves, etc.
Packing nut (14) too tight
Clear*.
Loosen (see page 10).
Loose packing nut (14) or worn throat Tighten packing nut (see page 10);
packings (3, 25)
replace throat packings.
Pump operates, but output low on Held open or worn intake valve.
down stroke
Clear; service.
Pump operates, but output low on Held open or worn fluid piston valve
Clear; service.
up stroke
or packings (29, 30)
Exhausted fluid supply
Refill; purge all air from the pump and
fluid lines.
Erratic or accelerated operation
Help open or worn intake valve.
Clear; service.
Clear; service.
Help open or worn fluid piston valve
or packings (29, 30)
* To determine if the fluid hose or gun is obstructed, relieve the pressure. Disconnect the fluid hose and place a container at the
pump fluid outlet to catch any fluid. Turn on the air just enough to start the pump (about 20–40 psi [140–280 kPa, 1.4–2.8 bar]). If
the pump starts when the air is turned on, the obstruction is in the fluid hose or gun.
308118
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Disconnecting the Displacement Pump
MODEL
224348
SHOWN
Torque to 20–30 ft-lb
(27–41 NS m) on Model 224348
Torque to10–15 ft-lb
1
(14–20 NS m) on Model 224350
WARNING
2
Lubricate
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 9.
1. Flush the pump, if possible. Stop the pump at the
bottom of its stroke. Relieve the pressure.
2. Disconnect the air and fluid hoses. Remove the
pump from its mounting. Note the relative position
of the pump’s fluid outlet (R) to the air motor’s air
inlet (S).
106
3. Unscrew the tie rod locknuts (112) from the tie
rods (102). Remove the cotter pin (109). Unscrew
the displacement rod (1) from the air motor (106).
Carefully pull the displacement pump (101) away
from the air motor (106). Inspect the o-ring (105).
See Fig. 3.
107
4. Refer to page 15 for displacement pump service.
To service the air motor, refer to the separate air
motor manual (306982 or 307043), supplied.
S
Reconnecting the Displacement Pump
102
1
105
1
2
1. Lubricate the o-ring (105) and check that it is in
place on the displacement rod (1). Orient the
pump’s fluid outlet (R) to the air motor’s air inlet
(S) as was noted in step 2 under Disconnecting
the Displacement Pump. Position the displace-
ment pump (101) on the tie rods (102). Screw the
locknuts (112) onto the tie rods (102) loosely. See
Fig. 3.
109
14
112
1
2. Screw the displacement rod (1) into the shaft of
the air motor (106) until the pin holes in the rod
and shaft align. Install the cotter pin (109).
R
3. Mount the pump and reconnect all hoses. Recon-
nect the ground wire if it was disconnected during
repair. Tighten the packing nut/wet-cup (14) so it is
just snug – no tighter. Fill the wet-cup with Graco
Throat Seal Liquid or compatible solvent.
33
34
4. Tighten the tie rod locknuts (112) evenly, and
torque as shown in Fig. 3.
101
5. Start the pump and run it at about 40 psi (280 kPa,
2.8 bar) air pressure, to check that it is operating
properly.
6. Check for fluid leakage at the packing nut/wet-cup
(14). Relieve the pressure before tightening the
packing nut/wet-cup.
0199B
Fig. 3
14 308118
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
5. Loosen the packing nut (14), then pull the dis-
Displacement Pump Service
placement rod (1) and connecting rod (8) out the
bottom of the outlet housing (5).
Disassembly
When disassembling the pump, lay out all removed
parts in sequence to ease reassembly. See Fig. 4.
6. Secure the flats of the displacement rod (1) in a
vise. Unscrew the coupling nut (7) from the dis-
placement rod. Remove the connecting rod (8) and
attached parts.
NOTES
D Standard Repair Kit 224403 (UHMWPE/PTFE
packings) is available. For the best results, use all
the new parts in the kit. Parts included in the kit are
denoted with one asterisk, for example (2*).
7. Place the flats of the piston mounting stud (13) in a
vise. Loosen the jam nut (9) and unscrew the
adapter (10) from the piston mounting stud (13).
Set the connecting rod (8) aside. Remove one
cotter pin (12) and the ball stop pin (11), taking not
which set of holes it is in. Then remove the ball
(16).
D
C
o
n
v
e
r
s
i
o
n
K
i
t
2
2
4
8
8
9
i
s
a
v
a
i
l
a
b
l
e
t
o
c
o
n
v
e
r
t
t
h
e
pump to all PTFE packings. See page 18.
D Clean all the parts thoroughly when disassembling.
Check them carefully for damage or wear, replacing
parts as needed.
8. Unscrew the piston stud (27) from the piston
mounting stud (13). Remove the piston packings
(29, 30), glands (28, 31) , shims (35), and washer
(26).
1. Remove the displacement pump from the air motor
as explained on page 14.
2. Unscrew the locking ring (20) from the cylinder
(15). See Fig. 4. Remove the intake valve housing
(21).
9. Remove the packing nut (14), throat packings (3,
25), and glands (2, 4) from the outlet housing (5).
3. Remove the o-ring (19), ball stop pin (17), and ball
(18) from the intake valve housing (21).
10. Inspect all parts for damage. Clean all parts and
threads with a compatible solvent before reassem-
bling. Inspect the polished outer surface of the
displacement rod (1) and inner surface of the
cylinder (15) for scratches, scoring, or other dam-
age, which can cause premature packing wear and
leaking. To check, run a finger over the surface or
hold the part up to the light at an angle. Be sure
the ball seats of the piston (27) and intake valve
housing (21) are not chipped or nicked. Replace
any worn or damaged parts.
4. Unscrew the cylinder (15) from the outlet housing
(5), note its orientation and carefully pull the cylin-
der off the pump. Remove the o-ring (6) from the
outlet housing.
NOTE: It is important to replace the cylinder in the
same orientation as both ends are NOT alike.
Failure to install correctly may result in failure of
pump or premature seal wear. For instructions on
how to verify correct orientation, see NOTE in step
7 on page 16.
308118
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
5. Place the flats of the displacement rod (1) in a
Displacement Pump Service
vise. Apply thread lubricant to the bottom threads
of the rod. Couple the connecting rod (8) to the
displacement rod with the coupling nut (7). TIghten
the nut securely.
Reassembly
1. Lubricate the throat packings and install them in
the outlet housing (5) one at a time as follows, with
the lips of the v-packings facing down: the male
gland (4*), one UHMWPE v-packing (3*), two
PTFE v-packings (25*), one UHMWPE v-packing
(3*), and the female gland (2*). Apply thread
lubricant to the packing nut (14), and screw it
loosely into the outlet housing. See Fig. 4.
6. Place the o-ring (6) into the outlet housing (5).
Slide the displacement rod and connecting rod
assembly up into the outlet housing (5) until the
displacement rod protrudes from the packing nut
(14).
2. Lubricate the piston packings and install them on
the piston stud (27) one at a time in the following
order, with the lips of the v-packing facing up: the
shims (35; use 0–3 as required), the female gland
(31*), one UHMWPE v-packing (30*), two PTFE
v-packings (29*), one UHMWPE v-packing (30*),
the male gland (28*), and the washer (26*). See
Fig. 4.
NOTE: Before replacing the pump cylinder, note its
orientation. Failure to install correctly may result in
failure of pump or premature seal wear. Inspect the
inner diameter of both ends of the cylinder for
smoothness and size. The rougher and larger end
should mate with the outlet housing (5) upon
reassembly.
3. Apply thread sealant and screw the piston stud
(27) onto the piston mounting stud (13). Torque to
50–70 ft-lb (68–95 NSm). Install the piston ball
(16*) on the piston seat. Slide the ball stop pin
(11*) into the desired set of holes, and secure with
the cotter pin (12*).
7. Apply thread lubricant to the top threads of the
cylinder (15). Slide the cylinder straight up over the
connecting rod (8) and displacement rod (1), being
careful not to scratch the cylinder by tilting it.
Screw the cylinder into the outlet housing (5).
4. Check that the coupling nut (7), jam nut (9) and
adapter (10) are in place on the connecting rod (8).
The bottom of the adapter (10) should be flush
with the end of the rod (8); tighten the jam nut (9)
down securely to lock these parts. Apply thread
sealant to the male threads of the adapter (10).
Screw the piston mounting stud (13) onto the
connecting rod adapter (10), and torque to 50–70
ft-lb (68–95 NSm).
8. Install the ball (18*), o-ring (19) and ball stop pin
(17*) in the intake valve housing (21). Apply thread
lubricant to the bottom threads of the cylinder (15).
Place the intake valve assembly in the locking ring
(20), and screw the ring onto the cylinder (15).
9. Reconnect the displacement pump to the motor as
explained on page 14.
16 308118
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Apply sealant and torque to
1
2
50–70 ft-lb (68–95 NSm)
14
5
Apply thread lubricant
2
SEE DETAIL A
1
6
DETAIL A: THROAT PACKINGS
2
14
7
5
15
8
2*
3*
25*
224349 Shown
3*
4*
LIPS OF
V–PACKINGS
MUST FACE
DOWN
DETAIL B: PISTON PACKINGS
13
*26
9
*28
*29
*30
10
1
1
*29
*31
35
12*
11*
256712 Base
13
SEE DETAIL B
36
37
*16
27
27
1
LIPS OF V–PACKINGS
MUST FACE UP
17*
38
39
2
20
r_254999_308118_1c
19
21
*18
0193B
Fig. 4
308118
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 224348, Series C
10:1 Ratio Presidentr Pump
Model 256713, Series A
10:1 Ratio Presidentr Pump (1.5 in. Female Inlet)
Includes items 101–112
REF PART
NO. NO.
DESCRIPTION
QTY
101 224349}
DISPLACEMENT PUMP ASSY
See pages 20 and 21 for parts
1
256712*
DISPLACEMENT PUMP ASSY, 1.5 in.
female inlet
See pages 20 and 21 for parts
ROD, tie; stainless steel;
3.5” (89 mm) shoulder–to–shoulder
SEAL, o–ring; nitrile rubber
AIR MOTOR
1
102 166237
106
3
1
105† 156082
106 207352
See manual 306982 for parts
ADAPTER, swivel; 1/2 npt(m) x
3/8 npsm(f)
PIN, cotter; stainless steel;
0.12” (3.2 mm) x 1.5” (3.8 mm)
NUT, lock; 3/8–16; stainless steel
1
1
107 158256
109† 101946
112 102021
1
3
{
Recommended “tool box” spare parts. Keep on hand to re-
duce downtime.
107
}
For 224348 assembly
For 256713 assembly
*
105†
102
109†
112
101
224348 shown
0199B
18 308118
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 224350, Series C
5:1 Ratio Monarkr Pump
Model 256714, Series A
5:1 Ratio Monarkr Pump (1.5 in. Female Inlet)
Includes items 101–112
REF PART
NO. NO.
DESCRIPTION
QTY
101 224349}
256712*
DISPLACEMENT PUMP ASSY
See pages 20 and 21 for parts
1
DISPLACEMENT PUMP ASSY, 1.5 in.
female inlet
See pages 20 and 21 for parts
ROD, tie; stainless steel;
3.5” (89 mm) shoulder–to–shoulder
SEAL, o–ring; nitrile rubber
AIR MOTOR
See manual 307043 for parts
PIN, cotter; stainless steel;
0.12” (3.2 mm) x 1.5” (3.8 mm)
NUT, lock; 3/8–16; stainless steel
1
102 24B189
3
1
105† 156082
106 205997
106
1
109† 101946
112 102021
1
3
†
Recommended “tool box” spare parts. Keep on hand to re-
duce downtime.
}
For 224350 assembly
For 256714 assembly
*
105†
109†
102
112
101
224350 shown
0201B
308118
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 224349, Series C
Severe–Duty, Stainless Steel Displacement Pump
Model 256712, Series A
Severe–Duty, Stainless Steel Displacement Pump (1.5 in. Female Inlet)
Includes items 1–34
9
14
10
13
*2
11*
*3
*25
*3
12*
26*
224349 Shown
*4
5
28*
30*
29*
30*
31*
35
16*
27
†6
1
33
34
15
256712 Base
8
36
37
38
19†
18*
21
17*
7
39
20
r_254999_308118_2c
0192B
20 308118
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 224349, Series C
Severe–Duty, Stainless Steel Displacement Pump
Includes items 1–35
Model 256712, Series A
Severe–Duty, Stainless Steel Displacement Pump (1.5 in. Female Inlet)
Includes items 1–16, 22–39
REF PART
NO. NO.
OPTIONAL PTFE PACKING CONVERSION KIT
224889
DESCRIPTION
QTY
1
24C506
186988
176639
186987
192188
164782
166033
206449
166037
ROD, displacement; stainless steel
1
Use to convert the pump to all PTFE packings. Kit
must be purchased separately. Includes the following
items:
2*
3*
4*
5
GLAND, throat, female; stainless steel 1
V–PACKING, throat; UHMWPE
GLAND, throat, male; stainless steel
HOUSING, outlet; stainless steel
O–RING; PTFE
2
1
1
1
1
1
6†
Part No.
Description
Qty.
7
NUT, coupling
8
ROD, connecting; stainless steel
NUT, jam; 5/8–11 unc–2b;
stainless steel
100063
PIN, cotter; 1/16 in. x 1/2 in.;
stainless steel
9
2
4
1
10
166036
ADAPTER, connecting rod;
stainless steel
162866
162947
V-PACKING; PTFE
PIN, ball stop, intake;
1
1
11* 176637
12* 100063
PIN, ball stop, piston; stainless steel
stainless steel
1
1
1
1
4
1
1
1
3
PIN, cotter; 1/16” x 1/2”; stainless steel 2
STUD, mounting, piston;
13
14
15
176644
186995
24C504
186987
186988
176634
176635
176637
186989
186990
190484
GLAND, throat, male; stainless steel
GLAND, throat, female; stainless steel
WASHER, piston; stainless steel
V-PACKING, piston; PTFE
PIN, ball stop, piston; stainless steel
GLAND, piston, female; stainless steel
GLAND, piston, male; stainless steel
SHIM (use as required)
stainless steel
1
PACKING NUT/WET–CUP;
stainless steel
1
1
CYLINDER; stainless steel
BALL, piston; stainless steel;
0.875” (22 mm) dia.
16* 101917
1
1
17* 162947
18* 101968
PIN, ball stop, intake; stainless steel
BALL, intake; stainless steel;
1.25” (31 mm) dia.
1
1
1
19† 164846
20
21
O–RING; PTFE
164630
186991
RING, locking; stainless steel
HOUSING, valve, intake;
stainless steel
1
2
1
1
1
2
2
25* 162866
26* 176634
27
V–PACKING, throat; PTFE
WASHER, piston; stainless steel
STUD, piston; stainless steel
GLAND, piston, male; stainless steel
V–PACKING, piston; PTFE
V–PACKING, piston; UHMWPE
186993
28* 186990
29* 176635
30* 176638
31* 186989
GLAND, piston, female; stainless steel 1
BUNG ADAPTER
32
205573
Includes items 33 and 34
. THUMBSCREW; 1/4–20 unc x
1.5” (3.8 mm) long
1
33
101961
1
1
3
1
1
1
1
34
35
36
37
38
39
205572
190484
C38225
15J577
101178
15J574
. ADAPTER, bung; stainless steel
SHIM
PACKING, o–ring
RETAINER, ball, foot valve
BALL, metallic
HOUSING, valve, intake
*
The replacements for these parts are available in Standard
Repair Kit 224403 (UHMWPE/PTFE packings). Purchase
the kit separately.
†
Recommended “tool box” spare parts. Keep on hand to re-
duce downtime.
308118
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data (10:1 President)
Category
Data
Maximum fluid working pressure
Maximum air input pressure
Pump cycles per 1 gallon (3.8 liters)
Fluid flow at 60 cpm
1800 psi (12.4 MPa, 124 bar)
180 psi (1.25 MPa, 12.5 bar)
20
3 gallon (11.4 liters)
Recommended speed for optimum
pump life
15–25 cycles/min;
0.75–1.25 gpm (2.84 to 4.73 liters/min)
3
Air consumption
approx. 15 scfm (0.42 m /min) at 1 gpm (3.8 liters/min)
at 100 psi (0.7 MPa, 7 bar) air pressure
Weight
approx. 43 lb (19.5 kg)
Wetted parts
AISI 302, 303, 304, 316, and 17–4 PH grades of Stainless Steel;
Chrome Plating; PTFE; Ultra-High Molecular Weight Polyethylene
22 308118
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data (10:1 President)
Fluid Outlet Pressure Chart
CPM
MPa, BAR PSI
20
40
60
80
100
1800
1600
1400
1200
12.5, 125
11.0, 110
9.6, 96
A
B
C
D
1.25 MPa, 12.5 bar (180 psi) air pressure
0.7 MPa, 7 bar (100 psi) air pressure
0.49 MPa, 4.9 bar (70 psi) air pressure
0.28 MPa, 2.8 bar (40 psi) air pressure
A
To find Outlet Pressure (MPa/bar/psi) at a specific
delivery (liter/min or gpm) and operating air pressure
(MPa/bar/psi):
1. Locate desired delivery along bottom of chart.
2. Read vertical line up to intersection with
selected fluid outlet pressure curve.
8.4, 84
7.0, 70 1000
800
4.2, 42 600
B
C
D
5.6, 56
Curve slopes from left to right.
Follow left to scale and read outlet pressure.
400
200
0
2.8, 28
1.4, 14
0
1
3.8
2
7.6
3
11.4
4
15.2
5
19.0
GPM
l/min
PUMP DELIVERY (Test Fluid: No. 10 Motor Oil)
Air Consumption Chart
CPM
3
m /min CFM
20
40
60
80
100
A
B
C
D
1.25 MPa, 12.5 bar (180 psi) air pressure
0.7 MPa, 7 bar (100 psi) air pressure
0.49 MPa, 4.9 bar (70 psi) air pressure
0.28 MPa, 2.8 bar (40 psi) air pressure
100
80
60
40
20
0
2.800
2.240
1.68
3
To find Pump Air Consumption (m /min or
CFM/min) at a specific delivery (liter/min or gpm)
and operating air pressure (MPa/bar/psi):
1. Locate desired delivery along bottom of chart.
2. Read vertical line up to intersection with
selected air consumption curve.
A
Curve slopes from right to left. Follow left to
scale and read air consumption.
B
C
1.12
D
0.56
0
1
2
3
4
5
GPM
l/min
3.8
7.6
11.4
15.2 19.0
PUMP DELIVERY (Test Fluid: No. 10 Motor Oil)
308118
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data (5:1 Monark)
Category
Data
Maximum fluid working pressure
Maximum air input pressure
Pump cycles per 1 gallon (3.8 liters)
Fluid flow at 60 cpm
900 psi (6.3 MPa, 63 bar)
180 psi (1.25 MPa, 12.5 bar)
24
2.5 gallon (9.46 liters)
Recommended speed for optimum
pump life
15–25 cycles/min;
0.63–1.04 gpm (2.38 to 3.94 liters/min)
3
Air consumption
approx. 8.2 scfm (0.23 m /min) at 1 gpm (3.8 liters/min)
at 100 psi (0.7 MPa, 7 bar) air pressure
Weight
approx. 30 lb (13.6 kg)
Wetted parts
AISI 302, 303, 304, 316, and 17–4 PH grades of Stainless Steel;
Chrome Plating; PTFE; Ultra-High Molecular Weight Polyethylene
24 308118
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data (5:1 Monark)
Fluid Outlet Pressure Chart
CPM
MPa, BAR PSI
5.6, 56 800
24
48
72
96
120
A
B
C
D
1.25 MPa, 12.5 bar (180 psi) air pressure
0.7 MPa, 7 bar (100 psi) air pressure
0.49 MPa, 4.9 bar (70 psi) air pressure
0.28 MPa, 2.8 bar (40 psi) air pressure
A
600
400
200
0
4.2, 42
2.8, 28
To find Outlet Pressure (MPa/bar/psi) at a specific
delivery (liter/min or gpm) and operating air pressure
(MPa/bar/psi):
1. Locate desired delivery along bottom of chart.
2. Read vertical line up to intersection with
selected fluid outlet pressure curve.
B
Curve slopes from left to right.
Follow left to scale and read outlet pressure.
1.4, 14
C
D
0
1
3.8
2
7.6
3
11.4
4
15.2
5
19.0
GPM
l/min
PUMP DELIVERY (Test Fluid: No. 10 Motor Oil)
Air Consumption Chart
CPM
3
m /min CFM
24
48
72
96
120
A
B
C
D
1.25 MPa, 12.5 bar (180 psi) air pressure
0.7 MPa, 7 bar (100 psi) air pressure
0.49 MPa, 4.9 bar (70 psi) air pressure
0.28 MPa, 2.8 bar (40 psi) air pressure
40
32
24
16
8
1.120
0.896
0.672
0.448
0.224
A
3
To find Pump Air Consumption (m /min or
CFM/min) at a specific delivery (liter/min or gpm)
and operating air pressure (MPa/bar/psi):
1. Locate desired delivery along bottom of chart.
2. Read vertical line up to intersection with
selected air consumption curve.
B
C
Curve slopes from right to left. Follow left to
scale and read air consumption.
D
0
0
1
2
3
4
5
GPM
l/min
3.8
7.6
11.4
15.2 19.0
PUMP DELIVERY (Test Fluid: No. 10 Motor Oil)
308118
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Mounting Hole
Layout
Model 224348 Shown
USE GASKET 166392
(ORDER SEPARATELY)
B
0.28” (7.1 mm) DIA.
4.38”
(111.3 mm)
DIA.
Model 224348:
3/8 npsm(f);
Model 224350:
3/8 npt(f)
AIR INLET
2.5”
(64 mm)
5.0”
(127 mm)
0775
A
3/4 npt(f)
FLUID OUTLET
C
34.75 in.
(883 mm)
MAXIMUM
0200A
0200A
Pump Model
224348
A
B
C
57.31 in.
14.63 in.
42.68 in.
(1456 mm)
(372 mm)
(1084 mm)
256713
224350
256714
58.19 in.
(1478 mm)
14.63 in.
(372 mm)
43.56 in.
(1106 mm)
54.28 in.
11.60 in.
42.68 in.
(1379 mm)
(295 mm)
(1084 mm)
55.16 in.
11.60 in.
43.56 in.
(1401 mm)
(295 mm)
(1106 mm)
26 308118
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
308118
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-
stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Information
patents.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you:
Phone: 612–623–6921 or Toll Free: 1–800–328–0211 Fax: 612–378–3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 308118
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES
S
P.O. BOX 1441
S
MINNEAPOLIS, MN 55440–1441
S
USA
Copyright 1991, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Revised February 2013
28 308118
Download from Www.Somanuals.com. All Manuals Search And Download.
|