Visual UpTime Select
ASE model 807-0115
4xT1/E1 inline probe ASE
W i t h L i n k S a f e c a p a b i l i t i e s
The Visual UpTime® Select™ 4xT1/E1 inline probe
ASE enhances the data analysis functionality of the
Visual UpTime Select system for enterprises with
two-to-four T1 or E1 circuits terminating at a single
location. The ASE provides up to 6.176 Mbps
(T-standard) or 8.192 Mbps (E-standard) of detailed
network traffic analysis and management, while
maintaining full wire speed pass-through of all
traffic. In its initial release, the ASE supports IP
Transport software over MultiLink Point-to-Point
Protocol (MLPPP) T1 links.
The 4xT1/E1 ASE includes LinkSafe™ technology
to protect circuit integrity in case of a power outage
and it also delivers a notification alarm if there is a
power failure.
Key features
• Four management ports
• MLPPP support on IP Transport software
• Inband management capability
• LinkSafe technology
Designed for locations with multiple circuits
terminating at a single device, the 4xT1/E1 is typi-
cally deployed as an inline probe between the service
provider’s edge device and the customer’s termination
equipment. The figure below highlights the multilink
deployment for the 4xT1/E1 ASE.
• Power loss detection
• Service Level Agreement (SLA) metrics
• Application analysis capability
• LMI spoofing
• LAN management port
• Realtime events
4xT1/E1 inline probe model 807-0115 front
4xT1/E1 inline probe model model 807-0115 rear
Optional LAN Connection
Bundled
T1 Line
WAN
CPE Router
4xT1/E1 inline ASE
LAN
4xT1/E1 inline probe model 807-0115 position on network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Visual UpTime Select
ASE model 807-0113
T1/E1 inline probe ASE
W i t h L i n k S a f e c a p a b i l i t i e s
The Visual UpTime® Select™ T1/E1 LinkSafe™ inline
When configured for use on an E1 network, the ASE
complies with the physical/electrical characteristics
defined by ITU-T G.703 at 2.048 Megabits per second
(Mbps). The ASE also complies with the synchronous
frame structure specifications defined by ITU-T G.704,
including the option to use channel 16 for data or
signalling. You can either connect to the E1 network
using a 120 ohm balanced cable or BNC coax 75 ohm
unbalanced cables.
Key features
probe ASE is deployed inline on a T1 or E1 access line,
• Inband management capabilities
typically between a service provider’s edge device and
CSU/DSU. This ASE supports Multi-Protocol software
for deployment in standard frame relay or HDLC
networks and IP Transport software for deployment
in frame relay or HDLC-based networks that use IP
switching. The ASE also includes LinkSafe technology
to protect circuit integrity in case of an ASE outage,
as well as power failure notification.
• LinkSafe technology
• Power loss detection
• Multi-Protocol or IP Transport software
• Service Level Agreement (SLA) metrics
• Voice over IP (VoIP) analysis capability
• Application analysis capability
• LMI spoofing
• LAN management port
• Realtime events
T1/E1 inline probe model 807-0113 front view
T1/E1 inline probe model model 807-0113 rear view
Optional LAN Connection
T1/E1 Access Line
LAN
WAN
T1/E1 inline ASE
CSU/DSU
CPE Router
Visual UpTime
Select Server
T1/E1 inline probe model 807-0113 position on network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
T1/E1 inline probe ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
General
Dimensions
8.16” (20.7 cm) x 9.0” (22.8 cm) x 1.62”(4.1 cm)
2.10 lbs.
Weight
Data Rate
Timing Mode
1.544 Mbps synchronous
Derived externally from the T1 or E1 network,
user interface, or internally from the ASE.
0o to +40oC (+32o to +104o F)
-20o to +55oC (-4o to +131o×F)
Minimum of 3” (7.62 cm) space on sides.
10% to 80%, noncondensing
Operating Temperature
Storage Temperature
Clearance Requirement
Environment
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Operating and Storage
Humidity
Input
100 to 240 VAC
Power Requirements
T1 Network Interface
Frequency
50/60 Hz
Input Current Rating
Line Rate
0.5 amps
1.544 Mbps 50 bps synchronous
AMI or B9ZS line coding
ESF or D4 framing formats
0dB to -36dB
Line Format
Framing
Input Signal
Output Signal
Pulse Density
Connector
Hardware Warranties
0, -7.5dB, -15dB, -22.5dB LBO
AT&T 62411
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
8-pin modular jack—USOC: RJ48C
Network, User, or Internal
1 to 24 channels in any combination
2.048 Mbps 102.4 bps synchronous
HDB3 or AMI line coding
CRC4 or FAS framing formats
CAS, CCS, or Data
Timing
Channel Selection
Line Rate
E1 Network Interface
Line Format
Framing
Time Slot 16
Input Signal
Output Signal
Connector
Ordering Information
0dB to -43dB
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
0dB to LBO
RJ-45 (100 ohm balanced)
or BNC (75 ohm unbalanced)
Channel Selection
1-31 (includes channel 16
or 1-15, 17-31 (does not include channel 16)
Baud Rate
Parity
19200 or 9600 bps
8 data bits, no parity
1 stop bit
Serial Port Interface
Stop Bit
Electrical Format
Connector
Bite Rate
EIA RS-232, DTE
RJ-45
10 or 100 Mbps
Ethernet 10/100BaseT
Interface
Connector
8-pin modular jack: RJ-48
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643532 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0120
10/100 Ethernet inline ASE LE
W i t h L i n k S a f e c a p a b i l i t i e s
The Visual UpTime® Select™ 10/100 Ethernet
line between LAN devices, such as the LAN switch
and router (see figure). Other options include posi-
tioning the ASE on the Ethernet segment between a
subscriber’s router and a Network Terminating Unit
(NTU) such as a DSL modem or a Service Provider
switch (Ethernet as WAN access), or connecting the
ASE to a router or switch SPAN port.
Key features
inline ASE LE enhances the analysis functionality
of the Visual UpTime Select system for Ethernet
networks. The ASE provides up to 6 Mbps of detailed
network traffic analysis and management, while
maintaining full wire speed pass-through of all traf-
fic. It supports both IP Transport and LAN Visibility
software When deployed inline, the ASE includes
LinkSafe™ technology to protect circuit integrity if
in case of an ASE outage, as well as power failure
notification.
• Inline or SPAN mode deployment
• LinkSafe technology
• IP Transport or LAN Visibility software
• Voice over IP (VoIP) analysis capability
• Application analysis capability
• LAN management port
The LAN Visibility Ethernet ASE is deployed on
the LAN. The inline LAN Visibility ASE collects and
displays application flow traffic on the LAN between
clients and application server. In contrast, the IP
Transport ASE is designed to display only traffic to or
from the WAN, and ignore local traffic (such as be-
tween a client and an Internet or application server).
• Power loss detection
• Realtime events
Designed for business class DSL and cable, the
10/100 Ethernet inline ASE LE has a wide variety of
deployment options. The IP Transport Ethernet ASE is
typically deployed as an inline probe on the access
Ethernet inline probe model 807-0120 front view
Client
Access
Line(s)
Wide Area
Network
NTU
Customer IP Transport LAN Switch
Server
Ethernet ASE
device Edge Router
LAN
LAN Visibility
Ethernet ASE
Ethernet inline probe model 807-0120 deployed inline IP Transport and on LAN in LAN Visibility mode
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
Ethernt inline probe ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
7.5” (19.1 cm) x 6” (15.2 cm) x 1.5” (3.8 cm)
2.10 lbs.
General
Weight
Maximum Data Rate
Operating Temperature
Storage Temperature
Clearance Requirement
Input
6 Mbps
0o to +40oC (+32o to +104o F)
-20o to +55oC (-4o to +131o×F)
Minimum of 3” (7.62 cm) space on sides.
100 to 240 VAC
Environment
Power Requirements
Frequency
50/60 Hz
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Input Current Rating
Bit Rate
0.5 amps
10/100 Mbps
LAN and WAN
Ethernet Interface
Connector
8-pin modular jack: RJ-45
19200 or 9600 bps
8 data bits, no parity
1 stop bit
Baud Rate
Serial Port Interface
Parity
Stop Bit
Electrical Format
Connector
EIA RS-232, DTE
RJ-45
Hardware Warranties
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
Ethernet inline probe model model 807-0120 rear view
Ordering Information
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643441 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0122
10/100 Ethernet inline ASE
W i t h L i n k S a f e c a p a b i l i t i e s
The Visual UpTime® Select™ 10/100 Ethernet
line between LAN devices, such as the LAN switch
and router (see figure). Other options include posi-
tioning the ASE on the Ethernet segment between a
subscriber’s router and a Network Terminating Unit
(NTU) such as a DSL modem or a Service Provider
switch (Ethernet as WAN access), or connecting the
ASE to a router or switch SPAN port.
Key features
inline ASE enhances the analysis functionality of the
Visual UpTime Select system for Ethernet networks.
The ASE provides up to 100 Mbps of detailed network
traffic analysis and management, while maintaining
full wire speed pass-through of all traffic. It supports
both IP Transport and LAN Visibility software When
deployed inline, the ASE includes LinkSafe™ technol-
ogy to protect circuit integrity if in case of an ASE
outage, as well as power failure notification.
• Inline or SPAN mode deployment
• LinkSafe technology
• IP Transport or LAN Visibility software
• Voice over IP (VoIP) analysis capability
• Application analysis capability
• Power loss detection
The LAN Visibility Ethernet ASE is deployed on
the LAN. The inline LAN Visibility ASE collects and
displays application flow traffic on the LAN between
clients and application server. In contrast, the IP
Transport ASE is designed to display only traffic to or
from the WAN, and ignore local traffic (such as be-
tween a client and an Internet or application server).
• LAN management port
• Realtime events
Designed for business class DSL and cable, the
10/100 Ethernet inline ASE has a wide variety of
deployment options. The IP Transport Ethernet ASE is
typically deployed as an inline probe on the access
Ethernet inline probe model 807-0122 front view
Client
Access
Line(s)
Wide Area
Network
NTU
Customer IP Transport LAN Switch
Server
Ethernet ASE
device Edge Router
LAN
LAN Visibility
Ethernet ASE
Ethernet inline probe model 807-0122 deployed inline IP Transport and on LAN in LAN Visibility mode
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
Ethernt inline probe ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
7.5” (19.1 cm) x 6” (15.2 cm) x 1.5” (3.8 cm)
2.10 lbs.
General
Weight
Maximum Data Rate
Operating Temperature
Storage Temperature
Clearance Requirement
Input
100 Mbps
0o to +40oC (+32o to +104o F)
-20o to +55oC (-4o to +131o×F)
Minimum of 3” (7.62 cm) space on sides.
100 to 240 VAC
Environment
Power Requirements
Frequency
50/60 Hz
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Input Current Rating
Bit Rate
0.5 amps
10/100 Mbps
LAN and WAN
Ethernet Interface
Connector
8-pin modular jack: RJ-45
19200 or 9600 bps
8 data bits, no parity
1 stop bit
Baud Rate
Serial Port Interface
Parity
Stop Bit
Electrical Format
Connector
EIA RS-232, DTE
RJ-45
Hardware Warranties
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
Ordering Information
Ethernet inline probe model model 807-0122 rear view
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643434 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0220
10/100/1000 Ethernet ASE
With SPAN mode capabilities
The Visual UpTime® Select™ 10/100/1000 Ethernet
ASE enhances the analysis functionality of Visual
UpTime Select for Ethernet networks. The ASE
provides up to 500 Mbps of detailed network traffic
analysis and management, while maintaining full wire
speed pass-through of all traffic. It supports both IP
Transport and LAN Visibility software
The LAN Visibility Ethernet ASE is deployed on the
LAN. The ASE collects and displays application flow
traffic on the LAN between clients and application
server. In contrast, the IP Transport ASE is designed
to display only traffic to or from the WAN, and ignore
local traffic (such as between a client and an Inter-
net or application server).
Key features
• 500 MB of total analysis
• SPAN mode deployment
• Deployable in DS3, NxDS3, Fractional
OC3, and Ethernet to Premises topologies
• IP Transport or LAN Visibility software
• Voice over IP (VoIP) analysis capability
• Application analysis capability
• LAN management port
Designed for business class DSL and cable, the
10/100/1000 Ethernet ASE has a wide variety of
deployment options. The IP Transport Ethernet ASE is
deployed off a LAN switch SPAN port (see figure).
• Realtime events
Ethernet inline probe model 807-0220 front view
Ethernet inline probe model model 807-0220 rear view
Customer
Edge Router
LAN Switch
Wide Area
Network
SPAN port
Ethernet ASE
LAN
Ethernet probe model 807-0220 deployed on a LAN switch SPAN port
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
Ethernt inline probe ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
17.3” (43.9 cm) x 12” (30.5 cm) x 3.5” (8.9 cm)
10.45 lbs.
General
Weight
Maximum Data Rate
Operating Temperature
Storage Temperature
Clearance Requirement
Input
500 Mbps
0o to +40oC (+32o to +104o F)
-20o to +55oC (-4o to +131o×F)
Minimum of 3” (7.62 cm) space on sides.
100 to 240 VAC
Environment
Power Requirements
Frequency
50/60 Hz
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Input Current Rating
Bit Rate
0.5 amps
10/100/1000 Mbps
LAN and WAN
Ethernet Interface
Connector
8-pin modular jack: RJ-45
19200 or 9600 bps
Baud Rate
Serial Port Interface
Parity
8 data bits, no parity
1 stop bit
Stop Bit
Electrical Format
Connector
EIA RS-232, DTE
9-pin D, male per EIA-574
Hardware Warranties
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
Ordering Information
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643429 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0106
HSSI inline probe ASE
W i t h L i n k S a f e c a p a b i l i t i e s
The Visual UpTime® Select™ HSSI LinkSafe™ inline
The ASE also includes LinkSafe technology to protect
circuit integrity in case of an ASE outage, as well as
power failure notification.
Key features
probe ASE is deployed inline on a High Speed Serial
• Inband management capabilities
Interface (HSSI) access line, typically between a
CSU/DSU and customer edge router. It is capable of
monitoring traffic flowing through a bi-directional
HSSI connection at data rates up to 44.7 Mbps.
The HSSI ASE supports Multi-Protocol software for
deployment in standard frame relay or HDLC networks
and IP Transport software for deployment in frame
relay or HDLC-based networks that use IP switching.
The HSSI ASE has two HSSI interfaces, Data Ter-
minal Equipment (DTE) for monitoring traffic to the
network and Data Communication Equipment (DCE)
for monitoring traffic from the network. Because of
its high speed capabilities, a HSSI ASE can support
data passed through the CSU/DSU from NxT1
and DS3 lines.
• LinkSafe technology
• Power loss detection
• Multi-Protocol or IP Transport software
• Service Level Agreement (SLA) metrics
• Application analysis capability
• LMI spoofing
• LAN management port
• Realtime events
HSSI inline probe model 807-0106 front view
HSSI inline probe model model 807-0106 rear view
Optional LAN
Connection
Access Line
LAN
WAN
CSU/DSU
Inline ASE
CPE Router
Visual UpTime
Select Server
HSSI inline probe model 807-0106 position on network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
HSSI inline probe ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
17.3” (43.9 cm) x 12” (30.5 cm) x 3.5” (8.9 cm)
10.45 lbs.
General
Weight
Data Rate
Timing Mode
0 to 44.736 Mbps synchronous
RD: Always synchronous with SCR
SD: Synchronous with SCT or SCTE
0o to +40oC (+32o to +104o F)
-20o to +55oC (-4o to +131o×F)
Minimum of 3” (7.62 cm) space on sides.
10% to 80%, noncondensing
Operating Temperature
Storage Temperature
Clearance Requirement
Environment
Power Requirements
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Operating and Storage
Humidity
Input
100 to 240 VAC
50/60 Hz
Frequency
Input Current Rating
Configuration
1 amp
Two HSSI interfaces: one DTE and one DCE for
monitoring to-network and from-network traffic.
HSSI Interface
Baud Rate
Parity
19200 or 9600 bps
8 data bits, no parity
1 stop bit
Serial Port Interface
Stop Bit
Hardware Warranties
Electrical Format
Connector
Bite Rate
EIA RS-232, DTE
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
9-pin D, male per EIA-574
10 or 100 Mbps
Ethernet 10/100BaseT
Interface
Connector
8-pin modular jack: RJ-48
Ordering Information
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643476 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0104
V.35 inline probe ASE
W i t h L i n k S a f e c a p a b i l i t i e s
The Visual UpTime® Select™ V.35 LinkSafe™ inline
The V.35 inline probe ASE supports V.35 connectiv-
ity through a V.35 Data Terminal Equipment (DTE)
interface on the network side and Data Communica-
tions Equipment (DCE) interface on the user side.
The ASE operates at data rates up to 2.048 Mbps,
deriving timing from the network-side and sourcing
timing on the user side. It also includes LinkSafe
technology to protect circuit integrity in case of an
ASE outage, as well as power failure notification.
Key features
probe ASE is deployed inline on a T1 access line,
• Inband management capabilities
typically between a CSU/DSU and customer premises
equipment. This ASE supports Multi-Protocol software
for deployment in standard frame relay or HDLC
networks and IP Transport software for deployment
in frame relay or HDLC-based networks that use IP
switching.
• LinkSafe technology
• Multi-Protocol or IP Transport software
• Service Level Agreement (SLA) metrics
• Voice over IP (VoIP) analysis capability
• Application analysis capability
• LMI spoofing
• LAN management port
• Power loss detection
• Realtime events
V.35 inline probe model 807-0104 front view
V.35 inline probe model model 807-0104 rear view
Optional LAN
Connection
Access Line
LAN
WAN
CSU/DSU
Inline ASE
CPE Router
Visual UpTime
Select Server
V.35 inline probe model 807-0104 position on network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
V.35 inline probe ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
8.16” (20.7 cm) x 9.0” (22.8 cm) x 1.62”(4.1 cm)
Plastic case with internal power supply
General
Weight
2.10 lbs.
Data Rate
Timing Mode
0 to 2.048 Mbps synchronous
RD: Always synchronous with SCR
SD: Synchronous with SCT or SCTE
0o to +40oC (+32o to +104o F)
-20o to +55oC (-4o to +131o×F)
Minimum of 3” (7.62 cm) space on sides.
10% to 80%, noncondensing
Operating Temperature
Storage Temperature
Clearance Requirement
Environment
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Operating and Storage
Humidity
Input
100 to 240 VAC
Power Requirements
Frequency
50/60 Hz
Input Current Rating
Configuration
Data and Clock Leads
Signaling Leads
Connector
0.5 amps
DCE for interfacing with DTE
ITU-T V.35
V.35 User Interface
(DCE)
EIA RS-232 (ITU-T V.28)
Female 34-pin V.35 connector
RTS, DTR
Hardware Warranties
Signaling
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
Configuration
Data and Clock Leads
Signaling Leads
Connector
DTE for interfacing with DCE
ITU-T V.35
V.35 Network
Interface
(DTE)
EIA RS-232 (ITU-T V.28)
Female 34-pin V.35 connector
CTS, RLSD, DSR
Signaling
Baud Rate
19200 or 9600 bps
8 data bits, no parity
1 stop bit
Serial Port Interface
Parity
Ordering Information
Stop Bit
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
Electrical Format
Connector
EIA RS-232, DTE
RJ-45
Bite Rate
10 or 100 Mbps
Ethernet 10/100BaseT
Interface
Connector
8-pin modular jack: RJ-48
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643465 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0105
X.21 inline probe ASE
W i t h L i n k S a f e c a p a b i l i t i e s
The Visual UpTime® Select™ X.21 LinkSafe™ inline
The ASE supports X.21 connectivity through a X.21
Data Terminal Equipment (DTE) interface on the
network side and Data Communications Equipment
(DCE) interface on the user side.
Key features
probe ASE is deployed inline on an access line, typical-
• Inband management capabilities
ly between a CSU/DSU and customer premises equip-
ment (CPE). It supports Multi-Protocol software for
deployment in standard frame relay or HDLC networks
and IP Transport software for deployment in frame
relay or HDLC-based networks that use IP switching.
• LinkSafe technology
The ASE operates at data rates up to 2.048 Mbps,
deriving timing from the network-side and sourcing
timing on the user side. It also includes LinkSafe
technology to protect circuit integrity in case of an
ASE outage, as well as power failure notification.
• Multi-Protocol or IP Transport software
• Service Level Agreement (SLA) metrics
• Voice over IP (VoIP) analysis capability
• Application analysis capability
• LMI spoofing
• LAN management port
• Power loss detection
• Realtime events
X.21 inline probe model 807-0105 front view
X.21 inline probe model model 807-0105 rear view
Optional LAN
Connection
Access Line
LAN
WAN
CSU/DSU
Inline ASE
CPE Router
Visual UpTime
Select Server
X.21 inline probe model 807-0105 position on network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
X.21 inline probe ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
8.16” (20.7 cm) x 9.0” (22.8 cm) x 1.62”(4.1 cm)
Plastic case with internal power supply
General
Weight
2.10 lbs.
Data Rate
Timing Mode
0 to 2.048 Mbps synchronous
RD: Always synchronous with SCR
SD: Synchronous with SCT or SCTE
0o to +40oC (+32o to +104o F)
-20o to +55oC (-4o to +131o×F)
Minimum of 3” (7.62 cm) space on sides.
10% to 80%, noncondensing
Operating Temperature
Storage Temperature
Clearance Requirement
Environment
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Operating and Storage
Humidity
Input
100 to 240 VAC
Power Requirements
Frequency
50/60 Hz
Input Current Rating
Configuration
Data and Clock Leads
Signaling Leads
Connector
0.5 amps
DCE for interfacing with DTE
ITU-CCITT X.21
X.21 User Interface
(DCE)
ITU-CCITT X.21
Female 15-pin X.21 connector
Hardware Warranties
Signaling
Indicate: Clear to Send control signal to the user
interface. Received and terminated by the ASE.
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
Configuration
Data and Clock Leads
Signaling Leads
Connector
DTE for interfacing with DCE
ITU-CCITT X.21
X.21 Network
Interface (DTE)
ITU-CCITT X.21
Female 15-pin X.21 connector
Signaling
Control: Request to Send control signal from the
user interface. On while power is applied by the
ASE.
Ordering Information
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
Baud Rate
Parity
19200 or 9600 bps
8 data bits, no parity
1 stop bit
Serial Port Interface
Stop Bit
Electrical Format
Connector
Bite Rate
EIA RS-232, DTE
RJ-45
10 or 100 Mbps
Ethernet 10/100BaseT
Interface
Connector
8-pin modular jack: RJ-48
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643152 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0200
DS3 inline probe ASE
W i t h L i n k S a f e c a p a b i l i t i e s
The Visual UpTime® Select™ DS3 LinkSafe™ inline
The DS3 inline probe ASE is designed for deploy-
ment at the network demarcation point between a
subscriber’s CPE and the WAN. It can be deployed in
ATM and mixed frame relay-ATM environments. The
figure below shows the ASE positioned at the edge of
an inter-worked frame relay-to-ATM network, allowing
for SLA messaging between a frame relay DLCI and an
ATM VPI/VCI.
Key features
probe ASE complies with Class A standards for
• Inband management capabilities
countries using DS3 ATM lines (U.S. and Canada) and
supports digital transmission at the DS3 rate of 44
Mbps. This ASE supports Multi-Protocol software for
deployment in standard ATM networks and IP Trans-
port software for deployment in ATM-based networks
that use IP switching. The ASE also includes LinkSafe
technology to protect circuit integrity in case of an
ASE outage, as well as power failure notification.
• LinkSafe technology
• Multi-Protocol or IP Transport software
• Service Level Agreement (SLA) metrics
• Application analysis capability
• LAN management port
• Realtime events
DS3 inline probe model 200 front view
DS3 inline probe model 200 rear view
LAN
Branch ASEs
Visual
UpTime
Select
server
Frame to ATM
Interworking
T1
CPE
Router
ATM ASE
Frame
Network
ATM
Network
DS3 inline probe model 200 on ATM/Frame network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
DS3 inline probe ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
1 EIA unit (1.75”) high x 19” wide rack-mountable
chassis
General
Weight
10 lbs.
Data Rate
to 45 Mbps synchronous
Derived externally from the network.
0o to +40oC (+32o to +104oF)
-20o to +55oC (-4o to +131oF)
Minimum of 3” (7.62 cm) space on sides.
10% to 90% non-condensing
100 to 240 VAC
Timing Mode
Operating Temperature
Storage Temperature
Clearance Requirement
Operating/Storage Humidity
Input
Environment
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Power Requirements
Network Interface
Frequency
50/60 Hz
Input Current Rating
Line Rate
0.5 amps
44.736 Mbps
Cell Delineation
Cell Scrambler
Line Build Out
Connector
HEC or PLCP
Enable or Disable
Long = more than 225 feet. Short = 225 feet or less.
4 BNC (75 ohm), Network Tx and Rx, CPE Tx and Rx
57600, 19200, or 9600 bps
8 data bits, no parity
1 stop bit
Hardware Warranties
Baud Rate
Serial Port Interface
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
Parity
Stop Bit
Electrical Format
Connector
EIA RS-232, DTE
9-pin D, male per EIA-574
10 or 100 Mbps
Bite Rate
Ethernet 10/100BaseT
Interface
Connector
8-pin modular jack: RJ-48
Ordering Information
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643490 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0201
E3 inline probe ASE
W i t h L i n k S a f e c a p a b i l i t i e s
The Visual UpTime® Select™ E3 LinkSafe™ inline
The E3 inline probe ASE is designed for deploy-
ment at the network demarcation point between a
subscriber’s CPE and the WAN. It can be deployed in
ATM and mixed frame relay-ATM environments. The
figure below shows the ASE positioned at the edge of
an inter-worked frame relay-to-ATM network, allowing
for SLA messaging between a frame relay DLCI and an
ATM VPI/VCI.
Key features
probe ASE complies with Class A standards for
countries using E3 ATM lines and supports digital
transmission at the E3 rate of 34 Mbps. This ASE
supports Multi-Protocol software for deployment in
standard ATM networks and IP Transport software
for deployment in ATM-based networks that use IP
switching. The ASE also includes LinkSafe technology
to protect circuit integrity in case of an ASE outage,
as well as power failure notification.
• Inband management capabilities
• LinkSafe technology
• Multi-Protocol or IP Transport software
• Service Level Agreement (SLA) metrics
• Application analysis capability
• LAN management port
• Realtime events
E3 inline probe model 201 front view
E3 inline probe model 201 rear view
LAN
Branch ASEs
Visual
UpTime
Select
server
Frame to ATM
Interworking
T1
CPE
Router
ATM ASE
Frame
Network
ATM
Network
E3 inline probe model 201 on ATM/Frame network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
E3 inline probe ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
1 EIA unit (1.75”) high x 19” wide rack-mountable
chassis
General
Weight
10 lbs.
Data Rate
to 34 Mbps synchronous
Derived externally from the network.
0o to +40oC (+32o to +104oF)
-20o to +55oC (-4o to +131oF)
Minimum of 3” (7.62 cm) space on sides.
10% to 90% non-condensing
100 to 240 VAC
Timing Mode
Operating Temperature
Storage Temperature
Clearance Requirement
Operating/Storage Humidity
Input
Environment
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Power Requirements
Network Interface
Frequency
50/60 Hz
Input Current Rating
Line Rate
0.5 amps
34.368 Mbps
Cell Delineation
Cell Scrambler
Connector
HEC or PLCP
Enable or Disable
4 BNC (75 ohm), Network Tx and Rx, CPE Tx and Rx
57600, 19200, or 9600 bps
8 data bits, no parity
1 stop bit
Baud Rate
Serial Port Interface
Hardware Warranties
Parity
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
Stop Bit
Electrical Format
Connector
EIA RS-232, DTE
9-pin D, male per EIA-574
10 or 100 Mbps
Bite Rate
Ethernet 10/100BaseT
Interface
Connector
8-pin modular jack: RJ-48
Ordering Information
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643483 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0202
OC-3c/STM-1 inline probe ASE
S i n g l e m o d e w i t h L i n k S a f e c a p a b i l i t i e s
The Visual UpTime® Select™ OC-3c/STM-1 LinkSafe™
inline probe ASE supports single mode ATM OC-3c
physical lines, with SONET and SDH standards, at
speeds up to 155 Mbps. This ASE supports Multi-Proto-
col software for deployment in standard ATM networks
and IP Transport software for deployment in ATM-based
networks that use IP switching. The ASE also includes
LinkSafe technology to protect circuit integrity in case
of an ASE outage, as well as power failure notification.
The OC-3c/STM-1 inline probe ASE is designed
Key features
for deployment at the network demarcation point
between a subscriber’s CPE and the WAN. It can be
deployed in ATM and mixed frame relay-ATM environ-
ments. The figure below shows the ASE positioned
at the edge of an inter-worked frame relay-to-ATM
network, allowing for SLA messaging between a frame
relay DLCI and an ATM VPI/VCI.
• Inband management capabilities
• LinkSafe technology
• Multi-Protocol or IP Transport software
• Service Level Agreement (SLA) metrics
• Application analysis capability
• LAN management port
• Realtime events
OC-3c inline probe model 202 front view
OC-3c inline probe model 202 rear view
LAN
Branch ASEs
Visual
UpTime
Select
server
Frame to ATM
Interworking
T1
CPE
Router
OC-3c
ATM ASE
Frame
Network
ATM
Network
OC-3c inline probe model 202 on ATM/Frame network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
OC-3c inline probe ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
1 EIA unit (1.75”) high x 19” wide rack-mountable
chassis
General
Weight
10 lbs.
Data Rate
to 155 Mbps synchronous
Derived externally from the network.
0o to +40oC (+32o to +104oF)
-20o to +55oC (-4o to +131oF)
Minimum of 3” (7.62 cm) space on sides.
10% to 90% non-condensing
100 to 240 VAC
Timing Mode
Operating Temperature
Storage Temperature
Clearance Requirement
Operating/Storage Humidity
Input
Environment
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Power Requirements
Network Interface
Frequency
50/60 Hz
Input Current Rating
Bypass
0.5 amps
5 volt 1 amp DC
Line Rate
155.52 Mbps
Line Mode
SONET or SDH
Cell Delineation
Cell Scrambler
Connectors
HEC
Enable or Disable
Hardware Warranties
2 Sff Duplex-LC, Network Tx and Rx, CPE Tx and Rx
1274 nm/1356 nm
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
Wavelength
Tx Average Output Power
Rx Sensitivity
Baud Rate
-11dBm (typical) Measured with single mode cable
-33dBm (typical)
57600, 19200, or 9600 bps
8 data bits, no parity
1 stop bit
Serial Port Interface
Parity
Stop Bit
Electrical Format
Connector
EIA RS-232, DTE
Ordering Information
9-pin D, male per EIA-574
10 or 100 Mbps
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
Bite Rate
Ethernet 10/100BaseT
Interface
Connector
8-pin modular jack: RJ-48
Compliant with Bellcore GR-253 CORE and ITE G.957 standards
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643526 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0203
OC-3c/STM-1 inline probe ASE
M u l t i m o d e w i t h L i n k S a f e c a p a b i l i t i e s
The Visual UpTime® Select™ OC-3c/STM-1 LinkSafe™
The OC-3c/STM-1 inline probe ASE is designed
for deployment at the network demarcation point
between a subscriber’s CPE and the WAN. It can be
deployed in ATM and mixed frame relay-ATM environ-
ments. The figure below shows the ASE positioned
at the edge of an inter-worked frame relay-to-ATM
network, allowing for SLA messaging between a frame
relay DLCI and an ATM VPI/VCI.
Key features
inline probe ASE supports multimode ATM OC-3c
• Inband management capabilities
physical lines, with SONET and SDH standards, at
speeds up to 155 Mbps. This ASE supports Multi-
Protocol software for deployment in standard ATM
networks and IP Transport software for deployment in
ATM-based networks that use IP switching. The ASE
also includes LinkSafe technology to protect circuit
integrity in case of an ASE outage, as well as power
failure notification.
• LinkSafe technology
• Multi-Protocol or IP Transport software
• Service Level Agreement (SLA) metrics
• Application analysis capability
• LAN management port
• Realtime events
OC-3c inline probe model 203 front view
OC-3c inline probe model 203 rear view
LAN
Branch ASEs
Visual
UpTime
Select
server
Frame to ATM
Interworking
T1
CPE
Router
OC-3c
ATM ASE
Frame
Network
ATM
Network
OC-3c inline probe model 203 on ATM/Frame network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
OC-3c inline probe ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
1 EIA unit (1.75”) high x 19” wide rack-mountable
chassis
General
Weight
10 lbs.
Data Rate
to 155 Mbps synchronous
Derived externally from the network.
0o to +40oC (+32o to +104oF)
-20o to +55oC (-4o to +131oF)
Minimum of 3” (7.62 cm) space on sides.
10% to 90% non-condensing
100 to 240 VAC
Timing Mode
Operating Temperature
Storage Temperature
Clearance Requirement
Operating/Storage Humidity
Input
Environment
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Power Requirements
Network Interface
Frequency
50/60 Hz
Input Current Rating
Bypass
0.5 amps
5 volt 1 amp DC
Line Rate
155.52 Mbps
Line Mode
SONET or SDH
Cell Delineation
Cell Scrambler
Connectors
HEC
Enable or Disable
Hardware Warranties
2 Sff Duplex-LC, Network Tx and Rx, CPE Tx and Rx
1270 nm/1380 nm
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
Wavelength
Tx Average Output Power
-16dBm (typical) Measured with 62.5µ/120
Multimedia cable
Rx Sensitivity
Baud Rate
Parity
-33dBm (typical)
57600, 19200, or 9600 bps
8 data bits, no parity
1 stop bit
Serial Port Interface
Stop Bit
Electrical Format
Connector
Bite Rate
EIA RS-232, DTE
Ordering Information
9-pin D, male per EIA-574
10 or 100 Mbps
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
Ethernet 10/100BaseT
Interface
Connector
8-pin modular jack: RJ-48
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643515 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0109
T1 CSU/DSU ASE
W i t h D S X - 1 , D r o p - a n d - I n s e r t c a p a b i l i t i e s
The Visual UpTime® Select™ T1 CSU/DSU ASE is
deployed on a T1 access line at the demarcation point
between the provider network and customer premises.
It supports full and fractional (FT1) T1 networks and
provides connectivity through V.35 and additional
digital cross connect signal (DSX-1) interfaces.
The ASE supports Multi-Protocol software for deploy-
ment in standard frame relay or HDLC networks and
IP Transport software for deployment in frame relay or
HDLC-based networks that use IP switching.
In addition to performing standard CSU/DSU
Key features
functions—such as BER tests, loopbacks, and power
failure detection—the ASE is capable of inserting
management traffic.
• Inband management capabilities
• Multi-Protocol or IP Transport software
• Service Level Agreement (SLA) metrics
• Drop-and-Insert capabilities through
DSX port
The ASE’s “drop-and-insert” feature provides a
secondary DSX-1 port that can connect to a Private
Branch Exchange at a customer’s site. T1 Timeslots
can be segmented for a PBX on the same circuit car-
rying data traffic (see figure).
• Voice over IP (VoIP) analysis capability
• Application analysis capability
• LMI spoofing
• LAN management port
• Power loss detection
• Realtime events
T1 CSU/DSU model 807-0109 front view
T1 CSU/DSU model 807-0109 rear view
CSU/DSU
ASE
T1 Access
V.35
Line
Line
Wide Area
Network
Visual
UpTime
Select
Optional LAN
Connection
PBX
PBX
Server
TelephoTneelephone
T1 CSU/DSU model 807-0109 position on network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
T1 CSU/DSU ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
8.16” (20.7 cm) x 9.0” (22.8 cm) x 1.62”(4.1 cm)
Plastic case with internal power supply.
General
Weight
2.10 lbs.
Data Rate
Timing Mode
1.544 Mbps synchronous
Derived externally from the T1 network or DSX-1
interface, or internally from the ASE.
0o to +40oC (+32o to +104o F)
-20o to +55oC (-4o to +131o×F)
Minimum of 3” (7.62 cm) space on sides.
10% to 90%, noncondensing
Operating Temperature
Storage Temperature
Clearance Requirement
Environment
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Operating and Storage
Humidity
Input
100 to 120 VAC
Power Requirements
T1 Network Interface
Frequency
50/60 Hz
Input Current Rating
Line Rate
0.5 amps
1.544 Mbps 50 bps synchronous
AMI or B9ZS line coding
ESF or D4 framing formats
ANSI T1.403, AT&T TR54016, Both, or None
0dB to -36dB
Line Format
Framing
ESF FDL
Hardware Warranties
Input Signal
Output Signal
Pulse Density
Connector
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
0, -7.5dB, -15dB, -22.5dB LBO
AT&T 62411
8-pin modular jack—USOC: RJ48C
Loop, DSX-1, or Internal
1 to 24 channels in any combination
DCE for interfacing with DTE
ITU-T V.35
Timing
Channel Selection
Configuration
Data and Clock Leads
Signaling Leads
Data Rates
Network DTE Interface
(Data Port)
Ordering Information
EIA RS-232 (ITU-T V.28)
56 kbps x N or 64 kbps x N (N = 1 through 24)
Selectable V.35 data inversion
Network selected-source timing
SCT, inverted SCT, SCTE
RLSD, CTS
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
HDLC Inversion
Transmit Timing Basis
Receive Timing Basis
Receive Line Data Not Valid
Connector
Female 34-pin V.35 connector
1.544 Mbps 50 bps
Line Rate
DSX-1 Interface
Line Format
AMI or B8ZS
Framing
ESF or D4 (SF)
Input Signal
Line Equalization
Connector
-1dB to -11dB
0 ft, 133 ft, 266 ft, 399 ft, 533 ft, 655 ft
RJ-45
Channel Selection
Specifications
1 to 24 channels in any combination
N E T W O R K S U P E R V I S I O N
19200 or 9600 bps baud rate, 8 data bits no parity,
1 stop bit, EIA RS-232 DTE electrical format, RJ-45
connector
Serial Port Interface
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
Bite Rate
Connector
10 or 100 Mbps
Ethernet 10/100BaseT
Interface
8-pin modular jack: RJ-48
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643395 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0110
T1 CSU/DSU ASE
The Visual UpTime® Select™ T1 CSU/DSU ASE is
IP Transport software for deployment in frame relay or
HDLC-based networks that use IP switching.
In addition to performing standard CSU/DSU
functions—such as BER tests, loopbacks, and power
failure detection—the ASE is capable of inserting
management traffic.
Key features
deployed on a T1 access line at the demarcation point
between the provider network and customer premises.
It supports full and fractional (FT1) T1 networks and
provides connectivity through V.35 interface.
• Inband management capabilities
• Multi-Protocol or IP Transport software
• Service Level Agreement (SLA) metrics
• Voice over IP (VoIP) analysis capability
• Application analysis capability
• LMI spoofing
The ASE supports Multi-Protocol software for deploy-
ment in standard frame relay or HDLC networks and
• LAN management port
• Power loss detection
• Realtime events
T1 CSU/DSU model 807-0110 front view
T1 CSU/DSU model 807-0110 rear view
Demarcation Point
T1 Access
Line
V.35
Line
Wide Area
Network
CSU/DSU
ASE
Visual
UpTime
Select
Server
Optional LAN
Connection
T1 CSU/DSU model 807-0110 position on network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
T1 CSU/DSU ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
8.16” (20.7 cm) x 9.0” (22.8 cm) x 1.62”(4.1 cm)
Plastic case with internal power supply.
General
Weight
2.10 lbs.
Data Rate
Timing Mode
1.544 Mbps synchronous
Derived externally from the T1 network or DSX-1
interface, or internally from the ASE.
0o to +40oC (+32o to +104o F)
-20o to +55oC (-4o to +131o×F)
Minimum of 3” (7.62 cm) space on sides.
10% to 90%, noncondensing
Operating Temperature
Storage Temperature
Clearance Requirement
Environment
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Operating and Storage
Humidity
Input
100 to 120 VAC
Power Requirements
T1 Network Interface
Frequency
50/60 Hz
Input Current Rating
Line Rate
0.5 amps
1.544 Mbps 50 bps synchronous
AMI or B9ZS line coding
ESF or D4 framing formats
ANSI T1.403, AT&T TR54016, Both, or None
0dB to -36dB
Line Format
Framing
ESF FDL
Hardware Warranties
Input Signal
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
Output Signal
Pulse Density
Connector
0, -7.5dB, -15dB, -22.5dB LBO
AT&T 62411
8-pin modular jack—USOC: RJ48C
Loop, DSX-1, or Internal
1 to 24 channels in any combination
DCE for interfacing with DTE
ITU-T V.35
Timing
Channel Selection
Configuration
Data and Clock Leads
Signaling Leads
Data Rates
Network DTE Interface
(Data Port)
Ordering Information
EIA RS-232 (ITU-T V.28)
56 kbps x N or 64 kbps x N (N = 1 through 24)
Selectable V.35 data inversion
Network selected-source timing
SCT, inverted SCT, SCTE
RLSD, CTS
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
HDLC Inversion
Transmit Timing Basis
Receive Timing Basis
Receive Line Data Not Valid
Connector
Female 34-pin V.35 connector
Specifications
19200 or 9600 bps baud rate, 8 data bits no parity,
1 stop bit, EIA RS-232 DTE electrical format, RJ-45
connector
Serial Port Interface
Bite Rate
Connector
10 or 100 Mbps
Ethernet 10/100BaseT
Interface
8-pin modular jack: RJ-48
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643388 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0111
T1 CSU/DSU ASE
W i t h M o d e m
The Visual UpTime® Select™ T1 CSU/DSU ASE is
This ASE features an internal modem that allows
users to establish a telephone connection to either
the ASE’s administrative interface or a pass-through
connection through the serial port.
Key features
deployed on a T1 access line at the demarcation point
between the provider network and customer premises.
It supports full and fractional (FT1) T1 networks and
provides connectivity through V.35 interface.
The ASE supports Multi-Protocol software for deploy-
ment in standard frame relay or HDLC networks and
IP Transport software for deployment in networks that
use IP switching.
• Inband management capabilities
• Multi-Protocol or IP Transport software
• Service Level Agreement (SLA) metrics
• Drop-and-Insert capabilities through
DSX port
In addition to performing standard CSU/DSU
functions—such as BER tests, loopbacks, and power
failure detection—the ASE is capable of inserting
management traffic.
• Internal modem
• Voice over IP (VoIP) analysis capability
• Application analysis capability
• LMI spoofing
• LAN management port
• Power loss detection
• Realtime events
T1 CSU/DSU model 807-0111 front view
T1 CSU/DSU model 807-0111 rear view
CSU/DSU
ASE
T1 Access
Line
V.35
Line
Wide Area
Network
Visual
UpTime
Select
Modem
Connection
Optional LAN
Connection
PBX
PBX
Server
T1 CSU/DSU model 807-0111 position on network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
T1 CSU/DSU ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
8.16” (20.7 cm) x 9.0” (22.8 cm) x 1.62”(4.1 cm)
Plastic case with internal power supply.
General
Weight
2.10 lbs.
Data Rate
Timing Mode
1.544 Mbps synchronous
Derived externally from the T1 network or DSX-1
interface, or internally from the ASE.
0o to +40oC (+32o to +104o F)
-20o to +55oC (-4o to +131o×F)
Minimum of 3” (7.62 cm) space on sides.
10% to 90%, noncondensing
Operating Temperature
Storage Temperature
Clearance Requirement
Environment
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Operating and Storage
Humidity
Input
100 to 120 VAC
Power Requirements
T1 Network Interface
Frequency
50/60 Hz
Input Current Rating
Line Rate
0.5 amps
1.544 Mbps 50 bps synchronous
AMI or B9ZS line coding
ESF or D4 framing formats
ANSI T1.403, AT&T TR54016, Both, or None
0dB to -36dB
Line Format
Framing
ESF FDL
Hardware Warranties
Input Signal
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
Output Signal
Pulse Density
Connector
0, -7.5dB, -15dB, -22.5dB LBO
AT&T 62411
8-pin modular jack—USOC: RJ48C
Loop, DSX-1, or Internal
1 to 24 channels in any combination
DCE for interfacing with DTE
ITU-T V.35
Timing
Channel Selection
Configuration
Data and Clock Leads
Signaling Leads
Data Rates
Network DTE Interface
(Data Port)
Ordering Information
EIA RS-232 (ITU-T V.28)
56 kbps x N or 64 kbps x N (N = 1 through 24)
Selectable V.35 data inversion
Network selected-source timing
SCT, inverted SCT, SCTE
RLSD, CTS
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
HDLC Inversion
Transmit Timing Basis
Receive Timing Basis
Receive Line Data Not Valid
Connector
Female 34-pin V.35 connector
Specifications
19200 or 9600 bps baud rate, 8 data bits no parity,
1 stop bit, EIA RS-232 DTE electrical format, RJ-45
connector
Serial Port Interface
Bite Rate
Connector
Connector
Standard
10 or 100 Mbps
8-pin modular jack: RJ-48
RJ11
Ethernet 10/100BaseT
Interface
Modem
FCC Part 68 and IC-CS03
US and Canada
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Compliance
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643374 D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0112
T1 CSU/DSU ASE
W i t h D S X - 1 , D r o p - a n d - I n s e r t , a n d M o d e m
The Visual UpTime® Select™ T1 CSU/DSU ASE is
deployed on a T1 access line at the demarcation point
between the provider network and customer premises.
It supports full and fractional (FT1) T1 networks and
provides connectivity through V.35 and additional
digital cross connect signal (DSX-1) interfaces.
The ASE supports Multi-Protocol software for deploy-
ment in standard frame relay or HDLC networks and IP
Transport software for deployment in networks that
use IP switching.
The ASE’s “drop-and-insert” feature provides a
Key features
secondary DSX-1 port that can connect to a Private
Branch Exchange at a customer’s site. T1 Timeslots
can be segmented for a PBX on the same circuit
carrying data traffic (see figure). The ASE’s internal
modem lets users establish a telephone connection
to either the ASE’s administrative interface or a pass-
through connection via the serial port.
• Inband management capabilities
• Multi-Protocol or IP Transport software
• Service Level Agreement (SLA) metrics
• Drop-and-Insert capabilities through
DSX port
• Internal modem
• Voice over IP (VoIP) analysis capability
• Application analysis capability
• LMI spoofing
• LAN management port
• Power loss detection
• Realtime events
T1 CSU/DSU model 807-0112 front view
T1 CSU/DSU model 807-0112 rear view
CSU/DSU
ASE
T1 Access
Line
V.35
Line
Wide Area
Network
Visual
UpTime
Select
Modem
Connection
Optional LAN
Connection
PBX
PBX
Server
T1 CSU/DSU model 807-0112 position on network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
T1 CSU/DSU ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
8.16” (20.7 cm) x 9.0” (22.8 cm) x 1.62”(4.1 cm)
Plastic case with internal power supply.
General
Weight
2.10 lbs.
Data Rate
Timing Mode
1.544 Mbps synchronous
Derived externally from the T1 network or DSX-1
interface, or internally from the ASE.
Operating Temperature
Storage Temperature
Clearance Requirement
Operating/Storage Humidity
Input
0o to +40oC (+32o to +104o F)
-20o to +55oC (-4o to +131o×F)
Minimum of 3” (7.62 cm) space on sides.
10% to 90%, noncondensing
100 to 120 VAC
Environment
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Power Requirements
T1 Network Interface
Frequency
50/60 Hz
Input Current Rating
Line Rate
0.5 amps
1.544 Mbps 50 bps synchronous
AMI or B9ZS line coding
ESF or D4 framing formats
ANSI T1.403, AT&T TR54016, Both, or None
0dB to -36dB
Line Format
Framing
ESF FDL
Hardware Warranties
Input Signal
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
Output Signal
Pulse Density
Connector
0, -7.5dB, -15dB, -22.5dB LBO
AT&T 62411
8-pin modular jack—USOC: RJ48C
Loop, DSX-1, or Internal
1 to 24 channels in any combination
DCE for interfacing with DTE
ITU-T V.35
Timing
Channel Selection
Configuration
Data and Clock Leads
Signaling Leads
Data Rates
Network DTE Interface
(Data Port)
Ordering Information
EIA RS-232 (ITU-T V.28)
56 kbps x N or 64 kbps x N (N = 1 through 24)
Selectable V.35 data inversion
Network selected-source timing
SCT, inverted SCT, SCTE
RLSD, CTS
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
HDLC Inversion
Transmit Timing Basis
Receive Timing Basis
Receive Line Data Not Valid
Connector
Female 34-pin V.35 connector
1.544 Mbps 50 bps
Line Rate
DSX-1 Interface
Line Format
AMI or B8ZS
Framing
ESF or D4 (SF)
Input Signal
-1dB to -11dB
Line Equalization
Connector
0 ft, 133 ft, 266 ft, 399 ft, 533 ft, 655 ft
RJ-45
Channel Selection
Specifications
1 to 24 channels in any combination
19200 or 9600 bps baud rate, 8 data bits no parity,
1 stop bit, EIA RS-232 DTE electrical format, RJ-45
connector
Serial Port Interface
N E T W O R K S U P E R V I S I O N
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Bite Rate
10 or 100 Mbps
Ethernet 10/100BaseT
Interface
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
Connector
8-pin modular jack: RJ-48
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 2643363 D-ENG-N Rev A
©
Specifications
RJ11 connector, FCC Part 68 and IC-CS03 standards,
compliance in US and Canada
Modem
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual UpTime Select
ASE model 807-0100
Dual-port Dual-analysis ASE
T1 CSU/DSU with DSX-1 and Drop-and-Insert capabilities
The Visual UpTime® Select™ Dual-port Dual-analysis
T1 CSU/DSU ASE is deployed on a T1 access line at the
demarcation point between the provider network and
customer premises. It supports frame relay/HDLC and
IP Transport capabilities.
separate frame relay ports (for example, voice over
FR1, plus SNA over FR2). In addition, domestic and
international frame relay services can exist on two
separate ports on the same access line.
Key features
• Inband management capabilities
• Multi-Protocol or IP Transport software
• Service Level Agreement (SLA) metrics
• Drop-and-Insert capabilities through
DSX port
In addition to performing standard CSU/DSU
functions—such as BER tests, loopbacks, and power
failure detection—the ASE is capable of inserting
management traffic. Up to 155 PVCs or IP circuits can
be managed per ASE.
This unit combines two model 109 T1 CSU/DSU ASEs
with a built-in connector cable and analyzes data on
both ports. The unit’s second port can be used for
a redundant router in the event of primary router
failure. Multiple traffic types can be concentrated on
• Voice over IP (VoIP) analysis capability
• Application analysis capability
• LMI spoofing
• LAN management port
• Second analysis port for redundant
router, different traffic types
• Power loss detection
• Realtime events
T1 CSU/DSU model 807-0109 front view (ASE model 100 is two model 109 units in a rack mount)
ASE 2
ASE 1
DSX
T1
ASE 2 PORT 2
ASE 1 PORT 1
T1-DSX Cable (801-0096)
T1 CSU/DSU model 807-0100 rear view
Wide Area
Network
CSU/DSU
Dual-port ASE
Optional LAN
PBX
Connection on
data 1
DSX-1
V.35 Ports
PBX
data 2
data 1
T1 CSU/DSU model 807-0100 on network
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
What are ASEs?
T1 CSU/DSU ASE specifcations
ASEs (Analysis Service Elements) are data
collection and network performance monitor-
ing hardware devices placed on a wide area
network (WAN) or Local Area Network (LAN)
as part of the Visual UpTime Select system,
which offers in-depth, real-time, and historical
visibility into the performance of your
Dimensions
8.16” (20.7 cm) x 9.0” (22.8 cm) x 1.62”(4.1 cm)
Plastic case with internal power supply.
General
Weight
2.10 lbs.
Data Rate
Timing Mode
1.544 Mbps synchronous
Derived externally from the T1 network or DSX-1
interface, or internally from the ASE.
0o to +40oC (+32o to +104o F)
-20o to +55oC (-4o to +131o×F)
Minimum of 3” (7.62 cm) space on sides.
10% to 90%, noncondensing
Operating Temperature
Storage Temperature
Clearance Requirement
Environment
applications infrastructure. In the system,
data gathered by ASEs is stored in the Visual
UpTime Select server and displayed and ana-
lyzed from the Visual UpTime Select Web client.
As a service level management tool, ASEs
indicate when services are being met, provide
warnings when services start to degrade, and
send alerts when services are not met.
Operating and Storage
Humidity
Input
100 to 240 VAC
Power Requirements
T1 Network Interface
Frequency
50/60 Hz
Input Current Rating
Line Rate
0.5 amps
1.544 Mbps 50 bps synchronous
AMI or B9ZS line coding
ESF or D4 framing formats
ANSI T1.403, AT&T TR54016, Both, or None
0dB to -36dB
Line Format
Framing
ESF FDL
Hardware Warranties
Input Signal
Output Signal
Pulse Density
Connector
Enhanced Gold, Bronze, and International
Gold ASE hardware warranty service programs
are available to help you maximize your
investment in Visual UpTime Select. For more
detailed warranty information, visit:
0, -7.5dB, -15dB, -22.5dB LBO
AT&T 62411
8-pin modular jack—USOC: RJ48C
Loop, DSX-1, or Internal
1 to 24 channels in any combination
DCE for interfacing with DTE
ITU-T V.35
Timing
Channel Selection
Configuration
Data and Clock Leads
Signaling Leads
Data Rates
Network DTE Interface
(Data Port)
Ordering Information
EIA RS-232 (ITU-T V.28)
56 kbps x N or 64 kbps x N (N = 1 through 24)
Selectable V.35 data inversion
Network selected-source timing
SCT, inverted SCT, SCTE
RLSD, CTS
For more details, please contact your Visual
UpTime Select authorized reseller or
Fluke Networks Sales at (800) 240-4010
or (301) 296-2300.
HDLC Inversion
Transmit Timing Basis
Receive Timing Basis
Receive Line Data Not Valid
Connector
Female 34-pin V.35 connector
1.544 Mbps 50 bps
Line Rate
DSX-1 Interface
Line Format
AMI or B8ZS
Framing
ESF or D4 (SF)
Input Signal
Line Equalization
Connector
-1dB to -11dB
0 ft, 133 ft, 266 ft, 399 ft, 533 ft, 655 ft
RJ-45
Channel Selection
Specifications
1 to 24 channels in any combination
N E T W O R K S U P E R V I S I O N
19200 or 9600 bps baud rate, 8 data bits no parity,
1 stop bit, EIA RS-232 DTE electrical format, RJ-45
connector
Serial Port Interface
Fluke Networks
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details, go to
Bite Rate
Connector
10 or 100 Mbps
Ethernet 10/100BaseT
Interface
8-pin modular jack: RJ-48
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 2/2006 264xxxx D-ENG-N Rev A
©
Download from Www.Somanuals.com. All Manuals Search And Download.
|