Preface
This preface describes the objectives and organization of this document and explains how to find
additional information on related products and services. This preface contains the following sections:
•
•
•
•
•
Objectives
This document describes the Cisco 7600 Ethernet Services Plus line cards that are supported on the Cisco
7600 series routers. This document also describes how to install the Cisco 7600 Series ES+ line cards
and how to troubleshoot the installation.
Changes to This Document
Table 1 records technical changes to this document. The table shows the Cisco IOS software release
number and document revision number for the change, the date of the change, and a brief summary of
the change.
Table 1
Document Revision History
Release No.
Revision Date
Change Summary
15.3(1)S
OL-16146-10 November 2012
OL-16146-09 July 2012
Added support for the 76-ES+XT-8TG
high queue card.
15.2(4)S
15.2(2)S
Added support for the 76-ES+T-8TG low
queue card.
OL-16146-08 March 2012
Added support for two new low queue
line cards:
•
•
76-ES+T+XC-20G
76-ES+T+XC-40G
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Table 1
Document Revision History
12.2(33)SRE
OL-16146-04 December 2009
Added support for the following line
cards:
•
•
•
•
•
•
7600-ES+20C3C
7600-ES+20C3CXL
7600-ES+40C3C
7600-ES+40C3CXL
76-ES+XT-2TG3C
76-ES+XT-4TG3C
Added support for additional DWDM
SFPs (DWDM-SFP-3346,
DWDM-SFP-3739, DWDM-SFP-4134,
DWDM-SFP-4532, DWDM-SFP-4931,
DWDM-SFP-5332, DWDM-SFP-5736,
DWDM-SFP-6141)
12.2(33)SRD3
OL-16146-03 September 2009
Added support for the following line
cards:
76-ES+T-20G
76-ES+T-2TG
76-ES+T-40G
76-ES+T-4TG
12.2(33)SRD1
12.2(33)SRD
OL-16146-02
Added support for the following ES+
Extended Transport (ES+XT) line cards:
•
•
76-ES+XT-2TG3CXL
76-ES+XT-4TG3CXL
OL-16146-01 February, 2007
Initial version.
Organization
This document contains the following chapters:
Section
Title
Description
Provides an introduction to the Cisco 7600 Series
Ethernet Services Plus line cards.
Provides a compatibility summary for the Cisco
7600 Series Ethernet Services Plus line cards. For
each supported ES+ line card, provides a summary
of characteristics and an overview.
Chapter 3 Preparing to Install a Cisco 7600
Describes the required tools, equipment, and
safety guidelines for installing Cisco 7600 Series
Ethernet Services Plus line cards.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Section
Title
Description
Chapter 4 Installing and Removing a Cisco
Describes the procedures for installing and
removing Cisco 7600 Series Ethernet Services
Plus line cards on a Cisco 7600 series router.
Describes the procedures for installing and
removing SFP and XFP modules on Cisco 7600
Series Ethernet Services Plus line cards.
Provides information for troubleshooting the
installation of Cisco 7600 Series Ethernet Services
Plus line cards. It also describes helpful debug
commands and provides packing instructions.
Related Documentation
The documentation listed below is available online and on the Documentation DVD.
Your router, switch, or gateway and the Cisco IOS software running on it contain extensive features,
which are documented in the following resources:
•
•
Cisco 7600 ES+ Ethernet Line Cards Configuration Guide
Cisco IOS software:
–
For Cisco IOS configuration information and support, refer to the configuration guide or
command reference for a Cisco IOS mainline release. You can also refer to the specific Cisco
IOS software document for a particular feature.
–
To see if a feature is supported by a Cisco IOS release, to locate the software document for that
feature, or to check the minimum software requirements of Cisco IOS software with the
hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com.
You must be a registered user on Cisco.com to access this tool. To access Software Advisor,
click Login at Cisco.com, type “Software Advisor” in the SEARCH box, and click GO. Click
the link for the Software Advisor tool.
Note
•
For international agency compliance, safety, and statutory information for WAN interfaces:
–
–
Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers
Site Preparation and Safety Guide
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS)
feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds
are a free service and Cisco currently supports RSS Version 2.0.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
C H A P T E R
1
Cisco 7600 Ethernet Services Plus Line Card
Product Overview
This chapter provides an introduction to the Cisco 7600 Series Ethernet Services Plus (ES+) line cards
and ES+ combo low queue line cards. It includes the following sections:
•
•
•
•
Introduction to the Cisco 7600 ES+ and ES+ Combo Low Queue
Line Cards
The Cisco 7600 Series ES+ line cards are a multiple-fabric, fixed-port Ethernet line card for the Cisco
7600 series routers that are capable of 40 gbps full-duplex traffic forwarding using a fixed port interface
design. The Cisco 7600 Series ES+ line card versions are:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
40-port version: 7600-ES+40G3C
40-port version: 7600-ES+40G3CXL
20-port version: 7600-ES+20G3C
20-port version: 7600-ES+20G3CXL
4-port version: 7600-ES+4TG3C
4-port version: 7600-ES+4TGCXL
2-port version: 7600-ES+2TG3C
2-port version: 7600-ES+2TGCXL
2-port version: 76-ES+XT-2TG3C
2-port version: 76-ES+XT-2TG3CXL
4-port version: 76-ES+XT-4TG3C
4-port version: 76-ES+XT-4TG3CXL
20-port version: 76-ES+T-20G
2-port version: 76-ES+T-2TG
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Cisco 7600 Ethernet Services Plus Line Card Product Overview
Introduction to the Cisco 7600 ES+ and ES+ Combo Low Queue Line Cards
•
•
•
•
•
•
•
•
•
•
40-port version: 76-ES+T-40G
4-port version: 76-ES+T-4TG
11-port version: 76-ES+XC-20G3C
11-port version: 76-ES+XC-20G3CXL
22-port version: 76-ES+XC-40G3C
22-port version: 76-ES+XC-40G3CXL
11-port version: 76-ES+T+XC-20G
22-port version: 76-ES+T+XC-40G
8-port version: 76-ES+T-8TG
8-port version: 76-ES+XT-8TG
The difference between the versions are the link interface daughter cards that accept small form-factor
pluggable (SFP, SFP+, or XFP1) optical transceivers. Additionally, each of the versions has a common
baseboard card and a control processor daughter card, except for the 8 port version (76-ES+T-8TG) which
has a different baseboard.
The SFP, SFP+, and XFP modules allow the line cards to be configured for different media types (copper or
fiber) and different optical requirements (single mode fiber or multimode fiber) as available.
See Table 1-4 for information about which SFPs, SFP+, or XFPs are accepted on the different Cisco 7600
Series ES+ line cards.
Product Overview
The Cisco 7600 Series ES+ line cards have the following features:
The system features listed here specify some of the key performance metrics and capabilities of the line
cards. The information below applies to all four line cards unless stated otherwise.
•
Line rate feature processing performance with 64 byte packets for four ports of 10 GE or forty ports
of GE (59.52Mpps). Note that the line card throughput is limited by the system switch fabric. The
packet processor and internal sections of the line card are full line rate throughput capable for
40GbE.
•
•
Large output buffers provide up to 200 mS of round-trip-time buffer (100 mS in each direction) per
10GE port or 10xGE ports to prevent transient output overloads from causing spurious packet loss.
Up to 32K queues (per 10GE port or 10xGE ports) per direction for input or output queuing and
scheduling.
•
•
•
Programmable ingress and egress feature processing capability through the Trident.
40+ Mpps Layer 3 or Layer 4 forwarding, 125Mpps Layer 2 forwarding.
Dual fabric attachment providing an aggregate bandwidth of 40Gb/s, full duplex (each fabric
channel provides 20Gb/s, full duplex).
•
512-MB boot disk
1. SFP modules are optics modules with speeds lower than 10 Gbps; SFP+ and XFP modules are optics modules
with speeds equal to or greater than 10 Gbps.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Cisco 7600 Ethernet Services Plus Line Card Product Overview
Introduction to the Cisco 7600 ES+ and ES+ Combo Low Queue Line Cards
Cisco 7600 Series Ethernet Services Plus Line Card Product Numbers
Table 1-1 lists the Cisco product numbers for the line cards.
Table 1-1
Cisco 7600 Ethernet Services Plus Line Card Product Numbers
Field-Replaceable Unit
Cisco Product Number (FRU) Product ID
Description
20xGE SFP with DFC 3C
20xGE SFP with DFC 3CXL
2x10GE XFP with DFC 3C
2x10GE XFP with DFC 3CXL
40xGE SFP with DFC 3C
40xGE SFP with DFC 3CXL
4x10GE XFP with DFC 3C
4x10GE XFP with DFC 3CXL
7600-ES+20G3C
7600-ES+20G3C=
7600-ES+20G3CXL=
7600-ES+2TG3C=
7600-ES+2TG3CXL=
7600-ES+40G3C=
7600-ES+40G3CXL=
7600-ES+4TG3C=
7600-ES+4TG3CXL=
76-ES+XT-2TG3C=
7600-ES+20G3CXL
7600-ES+2TG3C
7600-ES+2TG3CXL
7600-ES+40G3C
7600-ES+40G3CXL
7600-ES+4TG3C
7600-ES+4TG3CXL
76-ES+XT-2TG3C
7600 ES+XT, LAN/WAN PHY, OTN/G.709,
2x10GE, XFP, DFC3C
7600 ES+XT, LAN/WAN PHY, OTN/G.709,
2x10GE, XFP, DFC3CXL
76-ES+XT-2TG3CXL
76-ES+XT-4TG3C
76-ES+XT-2TG3CXL=
76-ES+XT-4TG3C=
7600 ES+XT, LAN/WAN PHY, OTN/G.709,
4x10GE, XFP, DFC3C
7600 ES+XT, LAN/WAN PHY, OTN/G.709,
4x10GE, XFP, DFC3CXL
76-ES+XT-4TG3CXL
76-ES+XT-4TG3CXL=
20xGE with DFC 3CXL
2x10GE with DFC 3CXL
40xGE with DFC 3CXL
4x10GE with DFC 3CXL
76-ES+T-20G
76-ES+T-2TG
76-ES+T-40G
76-ES+T-4TG
76-ES+XC-20G3C
76-ES+T-20G=
76-ES+T-2TG=
76-ES+T-40G=
76-ES+T-4TG=
76-ES+XC-20G3C=
7600 ES+XC, LAN/WAN PHY, OTN/G.709,
Combo 10x1GE/ 1x10GE, DFC3C
7600 ES+XC, LAN/WAN PHY, OTN/G.709,
Combo 10x1GE/ 1x10GE, DFC3CXL
76-ES+XC-20G3CXL
76-ES+XC-40G3C
76-ES+XC-40G3CXL
76-ES+T+XC-20G
76-ES+T+XC-40G
76-ES+XC-20G3CXL=
76-ES+XC-40G3C=
76-ES+XC-40G3CXL=
76-ES+T+XC-20G=
76-ES+T+XC-40G=
7600 ES+XC, LAN/WAN PHY, OTN/G.709,
Combo 20x1GE/ 2x10GE, DFC3C
7600 ES+XC, LAN/WAN PHY, OTN/G.709,
Combo 20x1GE/ 2x10GE, DFC3CXL
7600 ES+XC, LAN/WAN PHY, OTN/G.709,
Combo 10x1GE/ 1x10GE, DFC3CXL
7600 ES+XC, LAN/WAN PHY, OTN/G.709,
Combo 20x1GE/ 2x10GE, DFC3CXL
8x10GE with DFC 3CXL
8x10GE with DFC 3CXL
76-ES+T-8TG
76-ES+T-8TG=
76-ES+XT-8TG3CXL
76-ES+XT-8TG3CXL=
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Cisco 7600 Ethernet Services Plus Line Card Product Overview
Introduction to the Cisco 7600 ES+ and ES+ Combo Low Queue Line Cards
Note
The Distributed Forwarding Card (DFC) on a 7600 ES+ line card functions at the level of the lowest
common denominator DFC in the system. If the only DFC in a system is a DFC 3CXL, then the system
would operate at the 3CXL level. If a DFC 3CXL is configured in a system with a DFC3BXL present,
then the system will function at the DFC 3BXL level. Additionally, a DFC 3CXL provides for more
TCAM entries than does a DFC 3C.
Supported Platforms
Table 1-2 lists the supported router platforms for Cisco 7600 ES+ line cards:
Table 1-2 Cisco 7600 ES+ Line Card Supported Router Platforms
Cisco 7600 ES+ Line Card Supported Platform
7600-ES+20G3C
All Cisco 7600 series routers except for the Cisco 7603 router
7600-ES+20G3CXL
7600-ES+2TG3C
7600-ES+2TG3CXL
7600-ES+40G3C
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
7600-ES+40G3CXL
Except for the Cisco 7603 router, all Cisco 7600 series routers including
7603-S.
7600-ES+4TG3C
7600-ES+4TG3CXL
76-ES+XT-2TG3C
76-ES+XT-2TG3CXL
76-ES+XT-4TG3C
76-ES+XT-4TG3CXL
76-ES+T-20G
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
All Cisco 7600 series routers except for the Cisco 7603 router
76-ES+T-2TG
76-ES+T-40G
76-ES+T-4TG
76-ES+XC-20G3C
76-ES+XC-20G3CXL
76-ES+XC-40G3C
76-ES+XC-40G3CXL
76-ES+T+XC-20G
76-ES+T+XC-40G
76-ES+T-8TG
76-ES+XT-8TG3CXL
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Cisco 7600 Ethernet Services Plus Line Card Product Overview
Cisco IOS Software Release and Hardware Revision Requirements
Cisco IOS Software Release and Hardware Revision
Requirements
The Cisco 7600 ES+ line cards have certain Cisco IOS software requirements. Also, to ensure
compatibility with the software, your Cisco 7600 ES+ line card should have a specific hardware revision
number. The number is printed on a label affixed to the component side of the card and is displayed by
the show diag command.
Table 1-3 lists the hardware and software requirements for Cisco 7600 ES+ line cards.
Table 1-3
Cisco 7600 ES+ Line Card and Cisco IOS Release and Hardware Version
Compatibility
Required
Minimum Cisco IOS
Software Release
Cisco 7600 ES+ Line Card
Cisco Product Number Hardware Version
7600 ES+ Line Card, 20xGE SFP with 7600-ES+20G3C
DFC 3C
68-2868-05
68-3030-05
68-2867-04
68-3029-04
68-2869-05
68-3032-05
68-2866-06
68-3031-06
68-3558-01
Cisco IOS Release
12.2(33)SRD
7600 ES+ Line Card, 20xGE SFP with 7600-ES+20G3CXL
DFC 3CXL
Cisco IOS Release
12.2(33)SRD
7600 ES+ Line Card, 2x10GE XFP with 7600-ES+2TG3C
DFC 3C
Cisco IOS Release
12.2(33)SRD
7600 ES+ Line Card, 2x10GE XFP with 7600-ES+2TG3CXL
DFC 3CXL
Cisco IOS Release
12.2(33)SRD
7600 ES+ Line Card, 40xGE SFP with 7600-ES+40G3C
DFC 3C
Cisco IOS Release
12.2(33)SRD
7600 ES+ Line Card, 40xGE SFP with 7600-ES+40G3CXL
DFC 3CXL
Cisco IOS Release
12.2(33)SRD
7600 ES+ Line Card, 4x10GE XFP with 7600-ES+4TG3C
DFC 3C
Cisco IOS Release
12.2(33)SRD
7600 ES+ Line Card, 4x10GE XFP with 7600-ES+4TG3CXL
DFC 3CXL
Cisco IOS Release
12.2(33)SRD
7600 ES+XT, LAN/WAN PHY,
OTN/G.709, 2x10GE, XFP, DFC3C
76-ES+XT-2TG3C
76-ES+XT-2TG3CXL 68-3335-03
76-ES+XT-4TG3C 68-3557-01
76-ES+XT-4TG3CXL 68-3336-03
Cisco IOS Release
12.2(33)SRD1
7600 ES+XT, LAN/WAN PHY,
OTN/G.709, 2x10GE, XFP, DFC3CXL
Cisco IOS Release
12.2(33)SRD1
7600 ES+XT, LAN/WAN PHY,
OTN/G.709, 4x10GE, XFP, DFC3C
Cisco IOS Release
12.2(33)SRD1
7600 ES+XT, LAN/WAN PHY,
Cisco IOS Release
12.2(33)SRD1
OTN/G.709, 4x10GE, XFP, DFC3CXL
7600 ES+T Line Card, 20xGE SFP with 76-ES+T-20G
DFC 3CXL
68-3030-06
68-3029-05
Cisco IOS Release
12.2(33)SRD4
7600 ES+XT, LAN/WAN PHY,
OTN/G.709, Low Queue, 2x10GE, XFP,
DFC3CXL
76-ES+T-2TG
Cisco IOS Release
12.2(33)SRD4
7600 ES+T Line Card, 40xGE SFP with 76-ES+T-40G
DFC 3CXL
68-3032-06
Cisco IOS Release
12.2(33)SRD4
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Cisco 7600 Ethernet Services Plus Line Card Product Overview
Modular Optics Compatibility
Table 1-3
(continued)Cisco 7600 ES+ Line Card and Cisco IOS Release and Hardware Version
Compatibility (continued)
Required
Minimum Cisco IOS
Software Release
Cisco 7600 ES+ Line Card
Cisco Product Number Hardware Version
7600 ES+XT, LAN/WAN PHY,
OTN/G.709, Low Queue, 4x10GE, XFP,
DFC3CXL
76-ES+T-4TG
68-3031-05
Cisco IOS Release
12.2(33)SRD4
7600 ES+XC Combo 10x1GE/ 1x10GE, 76-ES+XC-20G3C
DFC3C
68-3168-06
Cisco IOS Release
12.2(33)SRE
7600 ES+XC Combo 10x1GE/ 1x10GE, 76-ES+XC-20G3CXL 68-3169-06
DFC3CXL
Cisco IOS Release
12.2(33)SRE
7600 ES+XC Combo 20x1GE/ 2x10GE, 76-ES+XC-40G3C
DFC3C
68-3166-06
Cisco IOS Release
12.2(33)SRE
7600 ES+XC Combo 20x1GE/ 2x10GE, 76-ES+XC-40G3CXL 68-3167-06
DFC3CXL
Cisco IOS Release
12.2(33)SRE
7600 ES+XC Combo low queue
10x1GE/ 1x10GE, DFC3CXL
76-ES+T+XC-20G
76-ES+T+XC-40G
76-ES+T-8TG
68-4492-2
Cisco IOS 15.2(2)S
Cisco IOS 15.2(2)S
Cisco IOS 15.2(4)S
Cisco IOS 15.3(1)S
7600 ES+XC Combo low queue
20x1GE/ 2x10GE, DFC3CXL
68-4492-1
7600 ES+T Low queue 8x 10GE,
DFC3CXL
7600 ES+T High queue 8x 10GE,
DFC3CXL
76-ES+XT-8TG3CXL 68-4765-01
The show diag slot_number, show version, and show hardware commands display the current
hardware configuration of the router, including the system software version that is currently loaded and
running, and the hardware revision number. For complete descriptions of show commands, refer to the
Cisco IOS Configuration Fundamentals Configuration Guide and the Cisco IOS Configuration
Fundamentals Command Reference for the installed Cisco IOS release.
If the command displays indicate that the Cisco IOS software is a version earlier than you need, check
the contents of flash memory to determine if the required images are available on your system. The dir
devicename command displays a list of all files stored in flash memory. If you do not have the correct
software version, contact Cisco customer service.
For software configuration information, refer to the Cisco IOS software configuration and command
reference publications for the installed Cisco IOS release. Also refer to the Cisco IOS software release
notes for additional information.
Modular Optics Compatibility
The Cisco 7600 Series ES+ line cards use small form-factor pluggable (SFP, SFP+, or XFP) optical
transceivers to provide network connectivity. Table 1-4 provides links to tables showing the supported
modules for the different Cisco 7600 Series ES+ line cards.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Cisco 7600 Ethernet Services Plus Line Card Product Overview
Modular Optics Compatibility
Table 1-4
Supported Optical Transceiver Modules
Line Cards
Supported Modules
7600-ES+20G3C
7600-ES+20G3CXL
Cisco 7600 ES+ 20G3C, -20G3CXL
Supported SFP Modules; see Table 2-16 on
7600-ES+2TG3C
7600-ES+2TG3CXL
7600-ES+40G3C
Cisco 7600 ES+ 2TG3C, -3CXL Supported
Cisco 7600 ES+ 40G3C, -40G3CXL
Supported SFP Modules; see Table 2-21 on
7600-ES+40G3CXL
7600-ES+4TG3C
Cisco 7600 ES+ 4TG3C, -4TG3CXL
Supported XFP Modules; see Table 2-10 on
7600-ES+4TG3CXL
76-ES+XT-2TG3C
Cisco 76-ES+XT-2TG3C, -2TG3CXL
Supported XFP Modules; see Table 2-26 on
76-ES+XT-2TG3CXL
76-ES+XT-4TG3C
Cisco 76-ES+XT-2TG3C, -2TG3CXL
Supported XFP Modules; see Table 2-31 on
76-ES+XT-4TG3CXL
76-ES+T-20G
Supported SFP Modules; see Table 2-16 on
76-ES+T-2TG
Supported XFP Modules; see Table 2-26 on
76-ES+T-40G
Supported SFP Modules; see Table 2-21 on
76-ES+T-4TG
Supported XFP Modules; see Table 2-31 on
76-ES+XC-20G3C
76-ES+XC-20G3CXL
76-ES+XC-40G3C
76-ES+XC-40G3CXL
Supported SFP Modules; see TBD; Supported
XFP Modules; see TBD
Supported SFP Modules; see TBD; Supported
XFP Modules; see TBD
Supported SFP Modules; see TBD; Supported
XFP Modules; see TBD
Supported SFP Modules; see TBD; Supported
XFP Modules; see TBD
76-ES+T-8TG
Supported SFP+ Modules; see Table 2-83
76-ES+XT-8TG
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Cisco 7600 Ethernet Services Plus Line Card Product Overview
Power Management
Power Management
The Cisco ES+ line cards consume chassis power; you must make sure the chassis is within the power
Table 1-5
Cisco 7600 ES+ Line Card Power Consumption
Cisco 7600 Series ES+ line cards
7600-ES+20G3C
Power Consumption (Maximum in Watts)
277
305
269
297
391
419
371
399
273
301
378
406
305
301
419
406
309
337
399
427
337
427
433
433
7600-ES+20G3CXL
7600-ES+2TG3C
7600-ES+2TG3CXL
7600-ES+40G3C
7600-ES+40G3CXL
7600-ES+4TG3C
7600-ES+4TG3CXL
76-ES+XT-2TG3C
76-ES+XT-2TG3CXL
76-ES+XT-4TG3C
76-ES+XT-4TG3CXL
76-ES+T-20G
76-ES+T-2TG
76-ES+T-40G
76-ES+T-4TG
7600-ES+XC-20G3C
7600-ES+XC-20G3CXL
7600-ES+XC-40G3C
7600-ES+XC-40G3CXL
76-ES+T+XC-20G
76-ES+T+XC-40G
76-ES+T-8TG
76-ES+XT-8TG
If the power limit is exceeded, the Cisco ES+ line card is not powered up and an error message is
displayed.
Router#%C7KPWR-SP-4-POWERDENIED:insufficient power, module in slot 3 power denied.
On a Cisco 7600 series router, use the show power command on the Route Processor to determine how
much power you have available in the chassis and how much is being used or reserved by line cards,
supervisor engines, and fan trays.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Cisco 7600 Ethernet Services Plus Line Card Product Overview
Power Management
Note
The show power command displays only the values programmed in the IDPROM and the IDPROM is
not dynamically updated for different power values.
This is sample output for the show power command on a Cisco 7600 series router:
Router# show power
system power redundancy mode = redundant
system power redundancy operationally = non-redundant
system power total =
system power used =
3795.12 Watts (90.36 Amps @ 42V)
3320.94 Watts (79.07 Amps @ 42V)
system power available = 474.18 Watts (11.29 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS
Type
Watts
A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1
2
WS-CAC-4000W-INT
none
3795.12 90.36 OK
OK
on
Pwr-Allocated Oper
Fan Type
---- ------------------ ------- ------ -----
WS-C6K-13SLT-FAN2 298.20 7.10 OK
Pwr-Requested Pwr-Allocated Admin Oper
Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
Watts
A @42V State
1
Slot Card-Type
2
3
4
7
8
9
10
11
12
13
7600-SIP-200
WS-X6724-SFP
7600-SIP-400
RSP720-3CXL-GE
RSP720-3C-GE
7600-ESM-BASE
7600-ES+20G3CXL
7600-SIP-600
7600-SIP-600
WS-X6704-10GE
240.24 5.72
125.16 2.98
265.02 6.31
354.06 8.43
354.06 8.43
304.92 7.26
297.36 7.08
341.88 8.14
341.88 8.14
398.16 9.48
240.24 5.72 on
125.16 2.98 on
265.02 6.31 on
354.06 8.43 on
354.06 8.43 on
304.92 7.26 on
297.36 7.08 on
341.88 8.14 on
341.88 8.14 on
398.16 9.48 on
on
on
on
on
on
on
on
on
on
on
Router#
This is sample output for the show power command on a Cisco 7600 series router for a
76-ES+T+XC-40G low queue combo card:
A3-2#show power
system power redundancy mode = redundant
system power redundancy operationally = non-redundant
system power total = 2671.20 Watts (63.60 Amps @ 42V)
system power used = 1477.14 Watts (35.17 Amps @ 42V)
system power available = 1194.06 Watts (28.43 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-6000W 2671.20 63.60 OK OK on
2 none
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
1 7600-SIP-600 341.88 8.14 341.88 8.14 on on
4 7600-ES20-GE3C 340.20 8.10 - - off off (admin request)
5 (Redundant Sup) - - 354.06 8.43 - -
6 RSP720-3CXL-GE 354.06 8.43 354.06 8.43 on on
7 7600-ES+20G3C 276.36 6.58 - - off off (admin request)
8 7600-ES20-GE3C 340.20 8.10 - - off off (admin request)
9 '76-ES+T+XC-40G' 427.14 10.17 427.14 10.17 on on
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Cisco 7600 Ethernet Services Plus Line Card Product Overview
Power Management
This is sample output for the show power command on a Cisco 7600 series router for a
76-ES+T+XC-20G low queue combo card:
A1-2#show power
system power redundancy mode = redundant
system power redundancy operationally = non-redundant
system power total = 2669.10 Watts (63.55 Amps @ 42V)
system power used = 2181.90 Watts (51.95 Amps @ 42V)
system power available = 487.20 Watts (11.60 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 PWR-2700-AC 2669.10 63.55 OK OK on
2 none
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 FAN-MOD-6HS 180.18 4.29 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
1 76-ES+T+XC-20G 337.26 8.03 337.26 8.03 on on
2 WS-X6748-GE-TX 325.50 7.75 325.50 7.75 on on
3 7600-ES20-10G3CXL 340.20 8.10 340.20 8.10 on on
4 7600-SIP-600 341.88 8.14 341.88 8.14 on on
5 (Redundant Sup) - - 328.44 7.82 - -
6 WS-SUP720-3BXL 328.44 7.82 328.44 7.82 on on
This is sample output for the show power command on a Cisco 7600 series router for a 76-ES+T-8TG
low queue card:
Router#show power
system power redundancy mode = redundant
system power redundancy operationally = non-redundant
system power total =
system power used =
2671.20 Watts (63.60 Amps @ 42V)
1536.36 Watts (36.58 Amps @ 42V)
system power available = 1134.84 Watts (27.02 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS
Type
Watts
A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1
2
WS-CAC-6000W
none
2671.20 63.60 OK
OK
on
Pwr-Allocated Oper
Fan Type
Watts
A @42V State
---- ------------------ ------- ------ -----
1
2
FAN-MOD-9SHS
FAN-MOD-9SHS
241.50 5.75 OK
241.50 5.75 OK
Pwr-Requested Pwr-Allocated Admin Oper
Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
Slot Card-Type
2
5
6
76-ES+T-8TG
(Redundant Sup)
RSP720-3C-GE
432.60 10.30
432.60 10.30 on
310.38 7.39 -
310.38 7.39 on
on
-
on
-
-
310.38 7.39
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
C H A P T E R
2
Overview: Cisco 7600 Series Ethernet Services
Plus Line Cards
This chapter describes the Cisco 7600 Series Ethernet Services + line cards that are supported on the
Cisco 7600 series routers and contains the following sections:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 Series Ethernet Services Plus Line Card Summary
Cisco 7600 Series Ethernet Services Plus Line Card Summary
Summary descriptions of the Cisco 7600 Cisco 7600 Series ES+ line cards that are supported on the
Table 2-1
Cisco 7600 ES+ Line Card Summary
Maximum Number Minimum Cisco
Product Numbers
Description
of SFPs or XFPs
IOS Release
7600-ES+20G3C,
7600 ES+ Line Card, 20xGE 20 SFPs
SFP with DFC 3C
Cisco IOS
Release
7600-ES+20G3CXL
12.2(33)SRD
7600 ES+ Line Card, 20xGE
SFP with DFC 3CXL
7600-ES+2TG3C,
7600-ES+2TG3CXL
7600-ES+40G3C,
7600 ES+ Line Card, 2x10GE 2 XFPs
XFP with DFC 3C
Cisco IOS
Release
12.2(33)SRD
7600 ES+ Line Card, 2x10GE
XFP with DFC 3CXL
7600 ES+ Line Card, 40xGE 40 SFPs
SFP with DFC 3C
Cisco IOS
Release
12.2(33)SRD
7600-ES+40G3CXL
7600-ES+4TG3C,
7600-ES+4TG3CXL
76-ES+XT-2TG3C,
76-ES+XT-2TG3CXL
7600 ES+ Line Card, 40xGE
SFP with DFC 3CXL
7600 ES+ Line Card, 4x10GE 4 XFPs
XFP with DFC 3C
Cisco IOS
Release
12.2(33)SRD
7600 ES+ Line Card, 4x10GE
XFP with DFC 3CXL
7600 ES+XT, LAN/WAN
PHY, OTN/G.709, 2x10GE,
XFP, DFC3C
2 XFPs
Cisco IOS
Release
12.2(33)SRD1
7600 ES+XT, LAN/WAN
PHY, OTN/G.709, 2x10GE,
XFP, DFC3CXL
76-ES+XT-4TG3C,
7600 ES+XT, LAN/WAN
PHY, OTN/G.709, 4x10GE,
XFP, DFC3C
4 XFPs
Cisco IOS
Release
12.2(33)SRD1
76-ES+XT-4TG3CXL
7600 ES+XT, LAN/WAN
PHY, OTN/G.709, 4x10GE,
XFP, DFC3CXL
76-ES+T-20G
76-ES+T-40G
76-ES+T-2TG
7600 ES+T Line Card, 20xGE 20 SFPs
SFP with DFC 3CXL
Cisco IOS
Release
12.2(33)SRD3
7600 ES+T Line Card, 40xGE 40 SFPs
SFP with DFC 3CX
Cisco IOS
Release
12.2(33)SRD3
7600 ES+XT, LAN/WAN
PHY, OTN/G.709,Low queue,
2x10GE, XFP, DFC3CXL
2 XFPs
Cisco IOS
Release
12.2(33)SRD3
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Identifying Slots and Subslots for the Cisco 7600 Cisco 7600 Series ES+ Line Cards
Table 2-1
Cisco 7600 ES+ Line Card Summary (continued)
Maximum Number Minimum Cisco
Product Numbers
Description
of SFPs or XFPs
IOS Release
76-ES+T-4TG3XCL
7600 ES+XT, LAN/WAN
PHY, OTN/G.709,Low queue,
4x10GE, XFP, DFC3CXL
4 XFPs
Cisco IOS
Release
12.2(33)SRD3
76-ES+XC-20G3C
7600 ES+XC Combo 10x1GE/ 10 SFPs, 1 XFP
1x10GE, DFC3C
Cisco IOS
Release
12.2(33)SRE
76-ES+XC-20G3CXL
7600 ES+XC Combo 10x1GE/
1x10GE, DFC3CXL
76-ES+XC-40G3C
7600 ES+XC Combo 20x1GE/ 20 SFPs, 2 XFPs Cisco IOS
2x10GE, DFC3C
Release
76-ES+XC-40G3CXL
12.2(33)SRE
7600 ES+XC Combo 20x1GE/
2x10GE, DFC3CXL
Checking Hardware and Software Compatibility
To check the minimum software requirements of Cisco IOS software with the hardware installed on your
router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether the
Cisco 7600 Series ES+ line cards within a system are compatible, but it does provide the minimum Cisco
IOS requirements for individual hardware modules or components.
Note
Access to this tool is limited to users with Cisco.com login accounts.
To access Software Advisor, click Login at Cisco.com, type “Software Advisor” in the SEARCH box,
and click GO. Click the link for the Software Advisor tool.
Choose a product family or enter a specific product number to search for the minimum supported
software release needed for your hardware.
Identifying Slots and Subslots for the Cisco 7600 Cisco 7600
Series ES+ Line Cards
This section describes how to specify the physical location of a Cisco 7600 Cisco 7600 Series ES+ line
cards on the Cisco 7600 series routers within the command-line interface (CLI) to configure or monitor
those devices.
Specifying the Slot Location for a Cisco 7600 Cisco 7600 Series ES+ Line Cards
The Cisco 7600 series routers support different chassis models, each of which supports a certain number
of chassis slots.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Identifying Slots and Subslots for the Cisco 7600 Cisco 7600 Series ES+ Line Cards
Note
The Cisco 7600 Series ES+ line cards are not supported with a Supervisor Engine 1, Supervisor
Engine 1A, Supervisor Engine 2, Supervisor Engine 720-3A, or Supervisor Engine 32.
For information about the chassis slots available in different Cisco 7600 series router models, see
Some commands allow you to display information about the Cisco 7600 Series ES+ line card itself, such
as show module, show idprom module, show hw-module slot, and show diagbus. These commands
require you to specify the chassis slot location where the Cisco 7600 Series ES+ line card that you want
information about is installed.
For example, to display status and information about the Cisco 7600 Series ES+ line card installed in
slot 10 of a Cisco 7609 router, enter the following command:
Router# show module 10
Mod Ports Card Type
Model
Serial No.
--- ----- -------------------------------------- ------------------ -----------
10
20 7600 ES+
7600-ES+20G3CXL
Fw Sw
JAE1151865I
Status
Mod MAC addresses
Hw
--- ---------------------------------- ------ ------------ ------------ -------
10 001d.e5e8.2a00 to 001d.e5e8.2a3f 0.301 12.2(33r)SRD 12.2(nightly Ok
Mod Sub-Module
Model
Serial
Hw
Status
---- --------------------------- ------------------ ----------- ------- -------
10 7600 ES+ DFC XL
10 7600 ES+ 20xGE SFP
7600-ES+3CXL
7600-ES+20G
JAE115188YM 0.200 Ok
JAE1151860R 0.301 Ok
Mod Online Diag Status
---- -------------------
10 Pass
Router#
For more information about Cisco 7600 Series ES+ line card commands, see the Cisco IOS Software
Note
The Cisco 7600 Series ES+ line card must be in a slot that provides two primary serial channels. Dual
serial channels are not available in all slots of a 13-slot chassis. Dual fabric connectivity is supported in
slots 9 to 13.
Cisco 7600 ES+ Line Card Slot, Bay, and Port Locations
The Cisco 7600 Series ES+ line card uses a <slot, port> numbering scheme. The slot refers to whichever
slot the line card occupies in the router. The port numbering begins at 1 on all versions of the Cisco 7600
Series ES+ line card. The upper limit depends on the card type. This physical port numbering is reflected
in CLI messages and all references to port numbers that are visible to the user.
Executing the show interface command for a Cisco 7600 Series ES+ line card located in slot 10 of a
Cisco 7600 series router chassis produces the following (only first six interfaces are shown):
Router# show interfaces gigabitEthernet 10/2
GigabitEthernet10/2 is up, line protocol is up (connected)
Hardware is X40G 1Gb 802.3, address is 000f.35c2.ec00 (bia 000f.35c2.ec00)
Description: connect to test 7/2
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Line Card Overview
reliability 255/255, txload 196/255, rxload 196/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s
input flow-control is off, output flow-control is off
Clock mode is auto
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:24, output hang never
Last clearing of "show interface" counters 00:00:12
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 772455000 bits/sec, 1419960 packets/sec
5 minute output rate 772455000 bits/sec, 1419960 packets/sec
L2 Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes
L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcast
L3 out Switched: ucast: 0 pkt, 0 bytes mcast: 0 pkt, 0 bytes
11363519 packets input, 772719292 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
11363519 packets output, 772719292 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
For more information about Cisco 7600 Series ES+ line card commands, see the Cisco IOS Software
Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Line Card Overview
The following sections describe the Cisco 7600 Series ES+ line card:
•
•
•
•
•
Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Line Card Processors
Table 2-2
Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Line Card Processors
Type
Speed Description
Processor
300 megahertz (MHz) internal operating Trident
frequency
Local control
processor
1333 MHz (1.3GHz)
MPC8548
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Line Card Overview
Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Line Card LEDs
The Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL line cards have Status and A/L (Active Loopback)
Figure 2-1
Cisco 7600 ES+ 2TG3C
7600-ES+2TG3C
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Figure 2-2
Cisco 7600 ES+ 2TG3CXL Faceplate
7600-ES+2TG3CXL
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Table 2-3
Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Physical Specifications
Table 2-4
7600-ES+ 2TG3C,7600-ES+ 2TG33CXL Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL line cards occupy
one module slot and can be operated in all Cisco 7600 series routers
except the Cisco 7603 router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
32 to 104°F (0 to 40°C)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Line Card Overview
Table 2-4
7600-ES+ 2TG3C,7600-ES+ 2TG33CXL Physical Specifications (continued)
Description
Specifications
Relative humidity
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Storage temperature
Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Line Card Memory Options
Table 2-5 lists the memory options available for the 7600-ES+ 2TG3C, -3CXL line cards:
Table 2-5
Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Line Card Memory Options
Line Card
Memory Options
Cisco 7600 ES+ 2TG3C
Cisco 7600 ES+ 2T3CXL
1 GB
2 GB
Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Supported XFP Modules
The Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL line cards support the XFP modules listed in
Table 2-6 Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Supported XFP Modules
XFP
Description
XFP-10GLR-OC192SR
Cisco Multirate 10.GBASE-LR and OC-192/STM-64 SR-1 XFP
Module for SMF
XFP-10GZR-OC192LR
XFP-10GER-192IR+
XFP-10GLR-OC192SR-L
XFP-10GLR-OC192IR-L
XFP-10G-MM-SR
Cisco Multirate 10GBASE-ZR and OC-192/STM-64 lR-2 XFP
Module for SMF.
Cisco Multirate 10GBASE-ER and OC-192/STM-64 IR-2 XFP
Module for SMF.
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF.
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF.
Cisco multirate XFP transceiver module for 10GBASE-SR Ethernet
and OC-192/STM-64 short-reach (SR-1) Packet-over-SONET/SDH
(POS) applications, SMF, dual LC connector, and Multimode fiber.
DWDM-XFP-60.61
DWDM-XFP-59.79
DWDM-XFP-58.98
DWDM-XFP-58.17
DWDM-XFP-56.55
DWDM-XFP-55.75
DWDM-XFP-54.94
DWDM XFP 1560.61 nm XFP (100 GHz ITU grid).
DWDM XFP 1559.79 nm XFP (100 GHz ITU grid).
DWDM XFP 1558.98 nm XFP (100 GHz ITU grid).
DWDM XFP 1558.17 nm XFP (100 GHz ITU grid).
DWDM XFP 1556.55 nm XFP (100 GHz ITU grid).
DWDM XFP 1555.75 nm XFP (100 GHz ITU grid).
DWDM XFP 1554.94 nm XFP (100 GHz ITU grid).
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Line Card Overview
Table 2-6 Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL Supported XFP Modules (continued)
XFP
Description
DWDM-XFP-54.13
DWDM-XFP-52.52
DWDM-XFP-51.72
DWDM-XFP-50.92
DWDM-XFP-50.12
DWDM-XFP-48.51
DWDM-XFP-47.72
DWDM-XFP-46.92
DWDM-XFP-46.12
DWDM-XFP-44.53
DWDM-XFP-43.73
DWDM-XFP-42.94
DWDM-XFP-42.14
DWDM-XFP-40.56
DWDM-XFP-39.77
DWDM-XFP-38.98
DWDM-XFP-38.19
DWDM-XFP-36.61
DWDM-XFP-35.82
DWDM-XFP-35.04
DWDM-XFP-34.25
DWDM-XFP-32.68
DWDM-XFP-31.90
DWDM-XFP-31.12
DWDM-XFP-30.33
DWDM XFP 1554.13 nm XFP (100 GHz ITU grid).
DWDM XFP 1552.52 nm XFP (100 GHz ITU grid).
DWDM XFP 1551.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.92 nm XFP (100 GHz ITU grid).
DWDM XFP 1550.12 nm XFP (100 GHz ITU grid).
DWDM XFP 1548.51 nm XFP (100 GHz ITU grid).
DWDM XFP 1547.72 nm XFP (100 GHz ITU grid).
DWDM XFP 1546.92 nm XFP (100 GHz ITU grid).
DWDM XFP 1546.12 nm XFP (100 GHz ITU grid).
DWDM XFP 1544.53 nm XFP (100 GHz ITU grid).
DWDM XFP 1543.73 nm XFP (100 GHz ITU grid).
DWDM XFP 1542.94 nm XFP (100 GHz ITU grid).
DWDM XFP 1542.14 nm XFP (100 GHz ITU grid).
DWDM XFP 1540.56 nm XFP (100 GHz ITU grid).
DWDM XFP 1539.77 nm XFP (100 GHz ITU grid).
DWDM XFP 1538.98 nm XFP (100 GHz ITU grid).
DWDM XFP 1538.19 nm XFP (100 GHz ITU grid).
DWDM XFP 1536.61 nm XFP (100 GHz ITU grid).
DWDM XFP 1535.82 nm XFP (100 GHz ITU grid).
DWDM XFP 1535.04 nm XFP (100 GHz ITU grid).
DWDM XFP 1534.25 nm XFP (100 GHz ITU grid).
DWDM XFP 1532.68 nm XFP (100 GHz ITU grid).
DWDM XFP 1531.90 nm XFP (100 GHz ITU grid).
DWDM XFP 1531.12 nm XFP (100 GHz ITU grid).
DWDM XFP 1530.33 nm XFP (100 GHz ITU grid).
The XFP modules provide high-speed serial links at the following rates: 9.95 Gbps (OC-192) and
10.3125 Gbps (10 Gigabit Ethernet) on single-mode fiber (SMF). The transmit side recovers and retimes
the 10-Gbps serial data and passes it to a laser driver. The laser driver biases and modulates a 1310-nm
or 1550-nm laser, enabling data transmission over SMF through an LC connector. The receive side
recovers and retimes the 10-Gbps optical data stream from a photo-detector transimpedance amplifier
and passes it to an output driver.
See the label on the XFP module for technology type and model.
XFP module dimensions are:
•
•
•
Height: 12.5 mm
Width: 18.35 mm
Length: 71.1mm
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Line Card Overview
Figure 2-3
XFP Module
Connectors and Cabling
The XFP optical transceiver module on the Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL line card
require dual LC/PC connectors. Only connections with patch cords with PC or UPC connectors are
supported. Patch cords with APC connectors are not supported. All cables and cable assemblies used
must be compliant with the standards specified below:
•
•
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
Figure 2-4 shows the cable type for use with the XFP optical transceiver module on the Cisco 7600 ES+
2TG3C, 7600 ES+ 2TG3CXL line card.
Figure 2-4
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Line Card Overview
The following sections describe the Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL line cards:
•
•
•
•
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Line Card Overview
•
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Line Card Processors
Table 2-7
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Line Card Processor
Type
Speed Description
CPU
300 megahertz (MHz) internal operating Trident
frequency
Local control
processor
1333 MHz (1.3GHz)
MPC8548
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Line Card LEDs
The Cisco 7600 ES+ 4TG3C, 7600 ES+4TG3CXL line cards have Status and A/L (Active Loopback)
Figure 2-5
Cisco 7600 ES+ 4TG3C Faceplate
7600-ES+4TG3C
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Figure 2-6
Cisco 7600 ES+ 4TG3CXL Faceplate
76-ES+XT-4TG3CXL
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Table 2-8
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled but there is not a valid Ethernet
link.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Line Card Overview
Table 2-8
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL LEDs (continued)
LED Label
Color
State
Meaning
Green
On
The port is enabled and a valid Ethernet link has been
established.
Off
Off
The port is not enabled by software.
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Physical Specifications
Table 2-9
7600-ES+ 4TG3C, 7600-ES+ 4TG3CXL Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL line cards occupy
one module slot and can be operated in all Cisco 7600 series routers
except the Cisco 7603 router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Line Card Memory Options
Table 2-10 lists the memory options available for the Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL line
cards:
Table 2-10
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Line Card Memory Options
Line Card
Memory Options
Cisco 7600 ES+ 4TG3C
1 GB
2 GB
Cisco 7600 ES+ 4TG3CXL
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Supported XFP Modules
The Cisco 7600 ES+ 4TG3C, -3CXL line cards support the XFP modules listed in Table 2-11
Table 2-11 Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Supported XFP Modules
XFP
Description
XFP-10GLR-OC192SR
Cisco Multirate 10GBASE-LR and OC-192/STM-64 SR-1 XFP
Module for SMF
XFP-10GZR-OC192LR
Cisco Multirate 10GBASE-ZR and OC-192/STM-64 lR-2 XFP
Module for SMF
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Line Card Overview
Table 2-11 Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Supported XFP Modules (continued)
XFP
Description
XFP-10GER-192IR+
Cisco Multirate 10GBASE-ER and OC-192/STM-64 IR-2 XFP
Module for SMF
XFP-10GLR-OC192SR-L
XFP-10GLR-OC192IR-L
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
DWDM-XFP-60.61
DWDM-XFP-59.79
DWDM-XFP-58.98
DWDM-XFP-58.17
DWDM-XFP-56.55
DWDM-XFP-55.75
DWDM-XFP-54.94
DWDM-XFP-54.13
DWDM-XFP-52.52
DWDM-XFP-51.72
DWDM-XFP-50.92
DWDM-XFP-50.12
DWDM-XFP-48.51
DWDM-XFP-47.72
DWDM-XFP-46.92
DWDM-XFP-46.12
DWDM-XFP-44.53
DWDM-XFP-43.73
DWDM-XFP-42.94
DWDM-XFP-42.14
DWDM-XFP-40.56
DWDM-XFP-39.77
DWDM-XFP-38.98
DWDM-XFP-38.19
DWDM-XFP-36.61
DWDM-XFP-35.82
DWDM-XFP-35.04
DWDM-XFP-34.25
DWDM-XFP-32.68
DWDM-XFP-31.90
DWDM XFP 1560.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1559.79 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.17 nm XFP (100 GHz ITU grid)
DWDM XFP 1556.55 nm XFP (100 GHz ITU grid)
DWDM XFP 1555.75 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.13 nm XFP (100 GHz ITU grid)
DWDM XFP 1552.52 nm XFP (100 GHz ITU grid)
DWDM XFP 1551.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1548.51 nm XFP (100 GHz ITU grid)
DWDM XFP 1547.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1544.53 nm XFP (100 GHz ITU grid)
DWDM XFP 1543.73 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.14 nm XFP (100 GHz ITU grid)
DWDM XFP 1540.56 nm XFP (100 GHz ITU grid)
DWDM XFP 1539.77 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.19 nm XFP (100 GHz ITU grid)
DWDM XFP 1536.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.82 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.04 nm XFP (100 GHz ITU grid)
DWDM XFP 1534.25 nm XFP (100 GHz ITU grid)
DWDM XFP 1532.68 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.90 nm XFP (100 GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Line Card Overview
Table 2-11 Cisco 7600 ES+ 4TG3C, 7600 ES+ 4TG3CXL Supported XFP Modules (continued)
XFP
Description
DWDM-XFP-31.12
DWDM-XFP-30.33
DWDM XFP 1531.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1530.33 nm XFP (100 GHz ITU grid)
The XFP modules provide high-speed serial links at the following rates: 9.95 Gbps (OC-192) and
10.3125 Gbps (10 Gigabit Ethernet) on single-mode fiber (SMF). The transmit side recovers and retimes
the 10-Gbps serial data and passes it to a laser driver. The laser driver biases and modulates a 1310-nm
or 1550-nm laser, enabling data transmission over SMF through an LC connector. The receive side
recovers and retimes the 10-Gbps optical data stream from a photo-detector transimpedance amplifier
and passes it to an output driver.
See the label on the XFP module for technology type and model.
XFP module dimensions are:
•
•
•
Height: 12.5 mm
Width: 18.35 mm
Length: 71.1mm
Figure 2-7
XFP Module
Connectors and Cabling
The XFP optical transceiver module on the Cisco 7600 ES+ 4TG3C, -3CXL line cards require dual
LC/PC connectors. Only connections with patch cords with PC or UPC connectors are supported. Patch
cords with APC connectors are not supported. All cables and cable assemblies used must be compliant
with the standards specified below:
•
•
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
Figure 2-8 shows the cable type for use with the XFP optical transceiver module on the Cisco 7600 ES+
4TG3C, -3CXL line card.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Line Card Overview
Figure 2-8
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Line Card Overview
The following sections describe the Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL line cards:
•
•
•
•
•
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Line Card Processors
Table 2-12
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
control
processor
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Line Card LEDs
The Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL line cards have Status and A/L (Active Loopback)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Line Card Overview
Figure 2-9
Cisco 7600 ES+ 20G3C Line Card Faceplate
7600-ES+20G3C
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Figure 2-10
Cisco 7600 ES+ 20G3CXL Line Card Faceplate
7600-ES+20G3CXL
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Table 2-13 provides LED descriptions.
Table 2-13
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Physical Specifications
The Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL line card physical specifications are shown in
Table 2-14
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Line Card Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 7600 ES+ 20G3C, -20G3CX line card occupies one module
slot and can be operated in all Cisco 7600 series routers except the
Cisco 7603 router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Line Card Overview
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Line Card Memory Options
Table 2-15 lists the memory options available for the Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL line
cards:
Table 2-15
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Line Card Memory Options
Line Card
Memory Options
Cisco 7600 ES+ 20G3C
Cisco 7600 ES+ 20G3XL
1 GB
2 GB
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Supported SFP Modules
The Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL line cards support the small form-factor pluggable
(SFP) optical transceiver modules listed in Table 2-16
Table 2-16
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Supported SFP Modules
SFP Modules
SFP-GE-S
SFP-GE-L
SFP-GE-Z
SFP-GE-T
GLC-BX-D
GLC-BX-U
Description
1000BASE-SX short wavelength; with DOM
1000BASE-LX/LH short wavelength; with DOM
1000BASE-ZX; with DOM
1000BASE-T SFP
1000BASE-BX10-D downstream bidirectional single fiber; with DOM
1000BASE-BX10-U upstream bidirectional single fiber; with DOM
CWDM-SFP-1470 Cisco CWDM SFP 1470 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1490 Cisco CWDM SFP 1490 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1510 Cisco CWDM SFP 1510 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1530 Cisco CWDM SFP 1530 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1550 Cisco CWDM SFP 1550 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1570 Cisco CWDM SFP 1570 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1590 Cisco CWDM SFP 1590 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1610 Cisco CWDM SFP 1610 nm; Gigabit Ethernet and 1G/2G FC
DWDM-SFP-3033 1000BASE-DWDM 1530.33 nm SFP (100-GHz ITU grid)
DWDM-SFP-3112 1000BASE-DWDM 1531.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-3190 1000BASE-DWDM 1531.90 nm SFP (100-GHz ITU grid)
DWDM-SFP-3268 1000BASE-DWDM 1532.68 nm SFP (100-GHz ITU grid)
DWDM-SFP-3425 1000BASE-DWDM 1534.25 nm SFP (100-GHz ITU grid)
DWDM-SFP-3504 1000BASE-DWDM 1535.04 nm SFP (100-GHz ITU grid)
DWDM-SFP-3582 1000BASE-DWDM 1535.82 nm SFP (100-GHz ITU grid)
DWDM-SFP-3661 1000BASE-DWDM 1536.61 nm SFP (100-GHz ITU grid)
DWDM-SFP-3819 1000BASE-DWDM 1538.19 nm SFP (100-GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Line Card Overview
Table 2-16
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Supported SFP Modules (continued)
SFP Modules
Description
DWDM-SFP-3898 1000BASE-DWDM 1538.98 nm SFP (100-GHz ITU grid)
DWDM-SFP-3977 1000BASE-DWDM 1539.77 nm SFP (100-GHz ITU grid)
DWDM-SFP-4056 1000BASE-DWDM 1540.56 nm SFP (100-GHz ITU grid)
DWDM-SFP-4214 1000BASE-DWDM 1542.14 nm SFP (100-GHz ITU grid)
DWDM-SFP-4294 1000BASE-DWDM 1542.94 nm SFP (100-GHz ITU grid)
DWDM-SFP-4373 1000BASE-DWDM 1543.73 nm SFP (100-GHz ITU grid)
DWDM-SFP-4453 1000BASE-DWDM 1544.53 nm SFP (100-GHz ITU grid)
DWDM-SFP-4612 1000BASE-DWDM 1546.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-4692 1000BASE-DWDM 1546.92 nm SFP (100-GHz ITU grid)
DWDM-SFP-4772 1000BASE-DWDM 1547.72 nm SFP (100-GHz ITU grid)
DWDM-SFP-4851 1000BASE-DWDM 1548.51 nm SFP (100-GHz ITU grid)
DWDM-SFP-5012 1000BASE-DWDM 1550.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-5092 1000BASE-DWDM 1550.92 nm SFP (100-GHz ITU grid)
DWDM-SFP-5172 1000BASE-DWDM 1551.72 nm SFP (100-GHz ITU grid)
DWDM-SFP-5252 1000BASE-DWDM 1552.52 nm SFP (100-GHz ITU grid)
DWDM-SFP-5413 1000BASE-DWDM 1554.13 nm SFP (100-GHz ITU grid)
DWDM-SFP-5494 1000BASE-DWDM 1554.94 nm SFP (100-GHz ITU grid)
DWDM-SFP-5575 1000BASE-DWDM 1555.75 nm SFP (100-GHz ITU grid)
DWDM-SFP-5655 1000BASE-DWDM 1556.55 nm SFP (100-GHz ITU grid)
DWDM-SFP-5817 1000BASE-DWDM 1558.17 nm SFP (100-GHz ITU grid)
DWDM-SFP-5898 1000BASE-DWDM 1558.98 nm SFP (100-GHz ITU grid)
DWDM-SFP-5979 1000BASE-DWDM 1559.79 nm SFP (100-GHz ITU grid)
DWDM-SFP-6061 1000BASE-DWDM 1560.61 nm SFP (100-GHz ITU grid)
DWDM-SFP-3346 DWDM SFP 1533.47 nm SFP (100 GHz ITU grid)
DWDM-SFP-3739 DWDM SFP 1537.40 nm SFP (100 GHz ITU grid)
DWDM-SFP-4134 DWDM SFP 1541.35 nm SFP (100 GHz ITU grid)
DWDM-SFP-4532 DWDM SFP 1545.32 nm SFP (100 GHz ITU grid)
DWDM-SFP-4931 DWDM SFP 1549.32 nm SFP (100 GHz ITU grid)
DWDM-SFP-5332 DWDM SFP 1553.33 nm SFP (100 GHz ITU grid)
DWDM-SFP-5736 DWDM SFP 1557.36 nm SFP (100 GHz ITU grid)
DWDM-SFP-6141 DWDM SFP 1561.42 nm SFP (100 GHz ITU grid)
SFPs are integrated fiber-optic transceivers that provide high-speed serial links from a port or slot to the
network. Various latching mechanisms can be used on the SFPs. There is no correlation between the type
of latch to the model type (such as SX or LX/LH) or technology type (such as Gigabit Ethernet). See the
label on the SFP for the technology type and model.
SFP dimensions are:
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 20G3C, 7600 ES+ 20G3CXL Line Card Overview
•
•
•
Height 0.03 in. (8.5 mm)
Width 0.53 in. (13.4 mm)
Depth 2.22 in. (56.5 mm)
SFP temperature ranges are:
•
•
•
COM—Commercial operating temperature range -5 to 70 degrees C (23 to 158 degrees F)
EXT—Extended operating temperature range -5 to 85 degrees C (23 to 185 degrees F)
IND—Industrial operating temperature range -40 to 85 degrees C (-40 to 85 degrees F)
Figure 2-11 shows a typical SFP module.
Figure 2-11 SFP Optics Module
Connectors and Cabling
The SFP optical transceiver module on the Cisco 7600 ES+ 20G3C, -3CXL line card require dual or
single LC/PC connectors. Only connections with patch cords with PC or UPC connectors are supported.
Patch cords with APC connectors are not supported. All cables and cable assemblies used must be
compliant with the standards specified below:
•
•
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable or
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Line Card Overview
Figure 2-12
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Line Card Overview
The following sections describe the Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL line cards:
•
•
•
•
•
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Line Card Processors
Table 2-17
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
control
processor
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Line Card LEDs
The Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL line cards have Status and A/L (Active Loopback)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Line Card Overview
Figure 2-13
Cisco 7600 ES+ 40G3C Line Card Faceplate
7600-ES+40G3C
EXT CLK
STATUS
CLASS
LASER
1
ETHERNET SERVICES MODULE
Figure 2-14
Cisco 7600 ES+ 40G3CXL Line Card Faceplate
7600-ES+40G3CXL
EXT CLK
STATUS
CLASS
LASER
1
ETHERNET SERVICES MODULE
Table 2-18 provides LED descriptions.
Table 2-18
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Physical Specifications
The Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL line card physical specifications are shown in
Table 2-19
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Line Card Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL line cards occupy
one module slot and can be operated in all Cisco 7600 series routers
except the Cisco 7603 router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Line Card Overview
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Line Card Memory Options
Table 2-20 lists the memory options available for the Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL line
cards:
Table 2-20
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Line Card Memory Options
Line Card
Memory Options
Cisco 7600 ES+ 40G3C
1 GB
2 GB
Cisco 7600 ES+ 40G3CXL
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Supported SFP Modules
The Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL line cards support the small form-factor pluggable
Table 2-21
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Supported SFP Modules
SFP Modules
SFP-GE-S
SFP-GE-L
SFP-GE-Z
SFP-GE-T
GLC-BX-D
GLC-BX-U
Description
1000BASE-SX short wavelength; with DOM
1000BASE-LX/LH short wavelength; with DOM
1000BASE-ZX; with DOM
1000BASE-T SFP
1000BASE-BX10-D downstream bidirectional single fiber; with DOM
1000BASE-BX10-U upstream bidirectional single fiber; with DOM
CWDM-SFP-1470 Cisco CWDM SFP 1470 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1490 Cisco CWDM SFP 1490 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1510 Cisco CWDM SFP 1510 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1530 Cisco CWDM SFP 1530 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1550 Cisco CWDM SFP 1550 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1570 Cisco CWDM SFP 1570 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1590 Cisco CWDM SFP 1590 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1610 Cisco CWDM SFP 1610 nm; Gigabit Ethernet and 1G/2G FC
DWDM-SFP-3033 1000BASE-DWDM 1530.33 nm SFP (100-GHz ITU grid)
DWDM-SFP-3112 1000BASE-DWDM 1531.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-3190 1000BASE-DWDM 1531.90 nm SFP (100-GHz ITU grid)
DWDM-SFP-3268 1000BASE-DWDM 1532.68 nm SFP (100-GHz ITU grid)
DWDM-SFP-3425 1000BASE-DWDM 1534.25 nm SFP (100-GHz ITU grid)
DWDM-SFP-3504 1000BASE-DWDM 1535.04 nm SFP (100-GHz ITU grid)
DWDM-SFP-3582 1000BASE-DWDM 1535.82 nm SFP (100-GHz ITU grid)
DWDM-SFP-3661 1000BASE-DWDM 1536.61 nm SFP (100-GHz ITU grid)
DWDM-SFP-3819 1000BASE-DWDM 1538.19 nm SFP (100-GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Line Card Overview
Table 2-21
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Supported SFP Modules (continued)
SFP Modules
Description
DWDM-SFP-3898 1000BASE-DWDM 1538.98 nm SFP (100-GHz ITU grid)
DWDM-SFP-3977 1000BASE-DWDM 1539.77 nm SFP (100-GHz ITU grid)
DWDM-SFP-4056 1000BASE-DWDM 1540.56 nm SFP (100-GHz ITU grid)
DWDM-SFP-4214 1000BASE-DWDM 1542.14 nm SFP (100-GHz ITU grid)
DWDM-SFP-4294 1000BASE-DWDM 1542.94 nm SFP (100-GHz ITU grid)
DWDM-SFP-4373 1000BASE-DWDM 1543.73 nm SFP (100-GHz ITU grid)
DWDM-SFP-4453 1000BASE-DWDM 1544.53 nm SFP (100-GHz ITU grid)
DWDM-SFP-4612 1000BASE-DWDM 1546.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-4692 1000BASE-DWDM 1546.92 nm SFP (100-GHz ITU grid)
DWDM-SFP-4772 1000BASE-DWDM 1547.72 nm SFP (100-GHz ITU grid)
DWDM-SFP-4851 1000BASE-DWDM 1548.51 nm SFP (100-GHz ITU grid)
DWDM-SFP-5012 1000BASE-DWDM 1550.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-5092 1000BASE-DWDM 1550.92 nm SFP (100-GHz ITU grid)
DWDM-SFP-5172 1000BASE-DWDM 1551.72 nm SFP (100-GHz ITU grid)
DWDM-SFP-5252 1000BASE-DWDM 1552.52 nm SFP (100-GHz ITU grid)
DWDM-SFP-5413 1000BASE-DWDM 1554.13 nm SFP (100-GHz ITU grid)
DWDM-SFP-5494 1000BASE-DWDM 1554.94 nm SFP (100-GHz ITU grid)
DWDM-SFP-5575 1000BASE-DWDM 1555.75 nm SFP (100-GHz ITU grid)
DWDM-SFP-5655 1000BASE-DWDM 1556.55 nm SFP (100-GHz ITU grid)
DWDM-SFP-5817 1000BASE-DWDM 1558.17 nm SFP (100-GHz ITU grid)
DWDM-SFP-5898 1000BASE-DWDM 1558.98 nm SFP (100-GHz ITU grid)
DWDM-SFP-5979 1000BASE-DWDM 1559.79 nm SFP (100-GHz ITU grid)
DWDM-SFP-6061 1000BASE-DWDM 1560.61 nm SFP (100-GHz ITU grid)
DWDM-SFP-3346 DWDM SFP 1533.47 nm SFP (100 GHz ITU grid)
DWDM-SFP-3739 DWDM SFP 1537.40 nm SFP (100 GHz ITU grid)
DWDM-SFP-4134 DWDM SFP 1541.35 nm SFP (100 GHz ITU grid)
DWDM-SFP-4532 DWDM SFP 1545.32 nm SFP (100 GHz ITU grid)
DWDM-SFP-4931 DWDM SFP 1549.32 nm SFP (100 GHz ITU grid)
DWDM-SFP-5332 DWDM SFP 1553.33 nm SFP (100 GHz ITU grid)
DWDM-SFP-5736 DWDM SFP 1557.36 nm SFP (100 GHz ITU grid)
DWDM-SFP-6141 DWDM SFP 1561.42 nm SFP (100 GHz ITU grid)
SFPs are integrated fiber-optic transceivers that provide high-speed serial links from a port or slot to the
network. Various latching mechanisms can be used on the SFPs. There is no correlation between the type
of latch to the model type (such as SX or LX/LH) or technology type (such as Gigabit Ethernet). See the
label on the SFP for the technology type and model.
SFP dimensions are:
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 7600 ES+ 40G3C, 7600 ES+ 40G3CXL Line Card Overview
•
•
•
Height 0.03 in. (8.5 mm)
Width 0.53 in. (13.4 mm)
Depth 2.22 in. (56.5 mm)
SFP temperature ranges are:
•
•
•
COM—Commercial operating temperature range -5 to 70 degrees C (23 to 158 degrees F)
EXT—Extended operating temperature range -5 to 85 degrees C (23 to 185 degrees F)
IND—Industrial operating temperature range -40 to 85 degrees C (-40 to 85 degrees F)
Figure 2-15 shows a typical SFP module.
Figure 2-15 SFP Optics Module
Connectors and Cabling
The SFP optical transceiver module on the Cisco 7600 ES+ 40G3C, -3CXL line card require dual or
single LC/PC connectors. Only connections with patch cords with PC or UPC connectors are supported.
Patch cords with APC connectors are not supported. All cables and cable assemblies used must be
compliant with the standards specified below:
•
•
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Line Card Overview
For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable or
Figure 2-16
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Line Card Overview
The following sections describe the Cisco 76-ES+XT-2TG3CX line cards:
•
•
•
•
•
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Line Card Processors
Table 2-22
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
control
processor
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Line Card LEDs
The Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL line cards have Status and A/L (Active Loopback)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Line Card Overview
Figure 2-17
Cisco 76-ES+XT-2TG3C Line Card Faceplate
76-ES+XT-2TG3C
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Figure 2-18
Cisco 76-ES+XT-2TG3CXL Line Card Faceplate
76-ES+XT-2TG3CXL
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Table 2-23 provides LED descriptions.
Table 2-23
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Physical Specifications
The Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL line card physical specifications are shown in
Table 2-24
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Line Card Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL line cards
occupy one module slot and can be operated in all Cisco 7600 series
routers except the Cisco 7603 router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Line Card Overview
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Line Card Memory Options
Table 2-25
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Line Card Memory Options
Line Card
Memory Options
Cisco 76-ES+XT-2TG3C
1GB
Cisco 76-ES+XT-2TG3CXL
2 GB
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Supported XFP Modules
The Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL line cards support the XFP modules listed in
Table 2-26 Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Supported XFP Modules
XFP
Description
XFP-10GLR-OC192SR
Cisco Multirate 10GBASE-LR and OC-192/STM-64 SR-1 XFP
Module for SMF
XFP-10GZR-OC192LR
XFP-10GER-192IR+
Cisco Multirate 10GBASE-ZR and OC-192/STM-64 lR-2 XFP
Module for SMF
Cisco Multirate 10GBASE-ER and OC-192/STM-64 IR-2 XFP
Module for SMF
XFP-10GLR-OC192SR-L
XFP-10GLR-OC192IR-L
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
DWDM-XFP-60.61
DWDM-XFP-59.79
DWDM-XFP-58.98
DWDM-XFP-58.17
DWDM-XFP-56.55
DWDM-XFP-55.75
DWDM-XFP-54.94
DWDM-XFP-54.13
DWDM-XFP-52.52
DWDM-XFP-51.72
DWDM-XFP-50.92
DWDM-XFP-50.12
DWDM-XFP-48.51
DWDM-XFP-47.72
DWDM XFP 1560.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1559.79 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.17 nm XFP (100 GHz ITU grid)
DWDM XFP 1556.55 nm XFP (100 GHz ITU grid)
DWDM XFP 1555.75 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.13 nm XFP (100 GHz ITU grid)
DWDM XFP 1552.52 nm XFP (100 GHz ITU grid)
DWDM XFP 1551.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1548.51 nm XFP (100 GHz ITU grid)
DWDM XFP 1547.72 nm XFP (100 GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Line Card Overview
Table 2-26 Cisco 76-ES+XT-2TG3C, 76-ES+XT-2TG3CXL Supported XFP Modules (continued)
XFP
Description
DWDM-XFP-46.92
DWDM-XFP-46.12
DWDM-XFP-44.53
DWDM-XFP-43.73
DWDM-XFP-42.94
DWDM-XFP-42.14
DWDM-XFP-40.56
DWDM-XFP-39.77
DWDM-XFP-38.98
DWDM-XFP-38.19
DWDM-XFP-36.61
DWDM-XFP-35.82
DWDM-XFP-35.04
DWDM-XFP-34.25
DWDM-XFP-32.68
DWDM-XFP-31.90
DWDM-XFP-31.12
DWDM-XFP-30.33
DWDM XFP 1546.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1544.53 nm XFP (100 GHz ITU grid)
DWDM XFP 1543.73 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.14 nm XFP (100 GHz ITU grid)
DWDM XFP 1540.56 nm XFP (100 GHz ITU grid)
DWDM XFP 1539.77 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.19 nm XFP (100 GHz ITU grid)
DWDM XFP 1536.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.82 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.04 nm XFP (100 GHz ITU grid)
DWDM XFP 1534.25 nm XFP (100 GHz ITU grid)
DWDM XFP 1532.68 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.90 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1530.33 nm XFP (100 GHz ITU grid)
The XFP modules provide high-speed serial links at the following rates: 9.95 Gbps (OC-192) and
10.3125 Gbps (10 Gigabit Ethernet) on single-mode fiber (SMF). The transmit side recovers and retimes
the 10-Gbps serial data and passes it to a laser driver. The laser driver biases and modulates a 1310-nm
or 1550-nm laser, enabling data transmission over SMF through an LC connector. The receive side
recovers and retimes the 10-Gbps optical data stream from a photo-detector transimpedance amplifier
and passes it to an output driver.
See the label on the XFP module for technology type and model.
XFP module dimensions are:
•
•
•
Height: 12.5 mm
Width: 18.35 mm
Length: 71.1mm
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Line Card Overview
Figure 2-19
XFP Module
Connectors and Cabling
The XFP optical transceiver module on the Cisco 7600 ES+ XT-2TG3C, 7600 ES+XT-2TG3CXL line
card require dual LC/PC connectors. Only connections with patch cords with PC or UPC connectors are
supported. Patch cords with APC connectors are not supported. All cables and cable assemblies used
must be compliant with the standards specified below:
•
•
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
Figure 2-20 shows the cable type for use with the XFP optical transceiver module on the Cisco 7600
ES+XT-2TG3C, 7600 ES+ XT-2TG3CXL line cards.
Figure 2-20
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Line Card Overview
The following sections describe the Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL line cards:
•
•
•
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Line Card Overview
•
•
Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Line Card Processors
Table 2-27
Cisco 7600 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
control
processor
Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Line Card LEDs
The Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL line cards have Status and A/L (Active Loopback)
Figure 2-21
Cisco 76-ES+XT-4TG3C Line Card Faceplate
76-ES+XT-4TG3C
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Figure 2-22
Cisco 76-ES+XT-4TG3CXL Line Card Faceplate
76-ES+XT-4TG3CXL
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Line Card Overview
Table 2-28 provides LED descriptions.
Table 2-28
Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Physical Specifications
The Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL line card physical specifications are shown in
Table 2-29
Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Line Card Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL line cards
occupy one module slot and can be operated in all Cisco 7600 series
routers except the Cisco 7603 router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Line Card Memory Options
Table 2-30 lists the memory options available for the Cisco 7600 76-ES+XT-4TG3C,
76-ES+XT-4TG3CXL line cards:
Table 2-30
Cisco 7600 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Line Card Memory Options
Line Card
Memory Options
Cisco 7600 76-ES+XT-4TG3C
1 GB
Cisco 7600 76-ES+XT-4TG3CXL
2 GB
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Line Card Overview
Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Supported SFP Modules
The Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL line cards support the XFP modules listed in
Table 2-31 Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Supported XFP Modules
XFP
Description
XFP-10GLR-OC192SR
Cisco Multirate 10GBASE-LR and OC-192/STM-64 SR-1 XFP
Module for SMF
XFP-10GZR-OC192LR
XFP-10GER-192IR+
Cisco Multirate 10GBASE-ZR and OC-192/STM-64 lR-2 XFP
Module for SMF
Cisco Multirate 10GBASE-ER and OC-192/STM-64 IR-2 XFP
Module for SMF
XFP-10GLR-OC192SR-L
XFP-10GLR-OC192IR-L
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
DWDM-XFP-60.61
DWDM-XFP-59.79
DWDM-XFP-58.98
DWDM-XFP-58.17
DWDM-XFP-56.55
DWDM-XFP-55.75
DWDM-XFP-54.94
DWDM-XFP-54.13
DWDM-XFP-52.52
DWDM-XFP-51.72
DWDM-XFP-50.92
DWDM-XFP-50.12
DWDM-XFP-48.51
DWDM-XFP-47.72
DWDM-XFP-46.92
DWDM-XFP-46.12
DWDM-XFP-44.53
DWDM-XFP-43.73
DWDM-XFP-42.94
DWDM-XFP-42.14
DWDM-XFP-40.56
DWDM-XFP-39.77
DWDM-XFP-38.98
DWDM-XFP-38.19
DWDM XFP 1560.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1559.79 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.17 nm XFP (100 GHz ITU grid)
DWDM XFP 1556.55 nm XFP (100 GHz ITU grid)
DWDM XFP 1555.75 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.13 nm XFP (100 GHz ITU grid)
DWDM XFP 1552.52 nm XFP (100 GHz ITU grid)
DWDM XFP 1551.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1548.51 nm XFP (100 GHz ITU grid)
DWDM XFP 1547.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1544.53 nm XFP (100 GHz ITU grid)
DWDM XFP 1543.73 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.14 nm XFP (100 GHz ITU grid)
DWDM XFP 1540.56 nm XFP (100 GHz ITU grid)
DWDM XFP 1539.77 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.19 nm XFP (100 GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Line Card Overview
Table 2-31 Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL Supported XFP Modules (continued)
XFP
Description
DWDM-XFP-36.61
DWDM-XFP-35.82
DWDM-XFP-35.04
DWDM-XFP-34.25
DWDM-XFP-32.68
DWDM-XFP-31.90
DWDM-XFP-31.12
DWDM-XFP-30.33
DWDM XFP 1536.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.82 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.04 nm XFP (100 GHz ITU grid)
DWDM XFP 1534.25 nm XFP (100 GHz ITU grid)
DWDM XFP 1532.68 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.90 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1530.33 nm XFP (100 GHz ITU grid)
The XFP modules provide high-speed serial links at the following rates: 9.95 Gbps (OC-192) and
10.3125 Gbps (10 Gigabit Ethernet) on single-mode fiber (SMF). The transmit side recovers and retimes
the 10-Gbps serial data and passes it to a laser driver. The laser driver biases and modulates a 1310-nm
or 1550-nm laser, enabling data transmission over SMF through an LC connector. The receive side
recovers and retimes the 10-Gbps optical data stream from a photo-detector transimpedance amplifier
and passes it to an output driver.
See the label on the XFP module for technology type and model.
XFP module dimensions are:
•
•
•
Height: 12.5 mm
Width: 18.35 mm
Length: 71.1mm
Figure 2-23 XFP Module
Connectors and Cabling
The XFP optical transceiver module on the Cisco 76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL line cards
require dual LC/PC connectors. Only connections with patch cords with PC or UPC connectors are
supported. Patch cords with APC connectors are not supported. All cables and cable assemblies used
must be compliant with the standards specified below:
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-20G Line Card Overview
•
•
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
Figure 2-4 shows the cable type for use with the XFP optical transceiver module on the Cisco
76-ES+XT-4TG3C, 76-ES+XT-4TG3CXL line cards.
Figure 2-24
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 76-ES+T-20G Line Card Overview
The following sections describe the Cisco 76-ES+T-20G line cards:
•
•
•
•
•
Cisco 76-ES+T-20G Line Card Processors
Table 2-32
Cisco 76-ES+T-20G Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
control
processor
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-20G Line Card Overview
Cisco 76-ES+T-20G Line Card LEDs
The Cisco 76-ES+T-20G line cards have Status and A/L (Active Loopback) LEDs, as shown in
Figure 2-25
Cisco 76-ES+T-20G Line Card Faceplate
76-ES+T-20G
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Table 2-33 provides LED descriptions.
Table 2-33
Cisco 76-ES+T-20G Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 76-ES+T-20G Physical Specifications
Table 2-34
Cisco 76-ES+T-20G Line Card Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 76-ES+T-20G line card occupies one module slot and can
be operated in all Cisco 7600 series routers except the Cisco 7603
router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-20G Line Card Overview
Cisco 76-ES+T-20G Line Card Memory Options
Table 2-35 lists the memory options available for the Cisco 76-ES+T-20G line cards:
Table 2-35 Cisco 76-ES+T-20GLine Card Memory Options
Line Card
Cisco 76-ES+T-20G
Memory Options
2 GB
Cisco 76-ES+T-20G Supported SFP Modules
The Cisco 76-ES+T-20G line cards support the small form-factor pluggable (SFP) optical transceiver
modules listed in Table 2-36
Table 2-36
Cisco 76-ES+T-20G Supported SFP Modules
SFP Modules
SFP-GE-S
SFP-GE-L
SFP-GE-Z
SFP-GE-T
GLC-BX-D
GLC-BX-U
Description
1000BASE-SX short wavelength; with DOM
1000BASE-LX/LH short wavelength; with DOM
1000BASE-ZX; with DOM
1000BASE-T SFP
1000BASE-BX10-D downstream bidirectional single fiber; with DOM
1000BASE-BX10-U upstream bidirectional single fiber; with DOM
CWDM-SFP-1470 Cisco CWDM SFP 1470 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1490 Cisco CWDM SFP 1490 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1510 Cisco CWDM SFP 1510 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1530 Cisco CWDM SFP 1530 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1550 Cisco CWDM SFP 1550 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1570 Cisco CWDM SFP 1570 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1590 Cisco CWDM SFP 1590 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1610 Cisco CWDM SFP 1610 nm; Gigabit Ethernet and 1G/2G FC
DWDM-SFP-3033 1000BASE-DWDM 1530.33 nm SFP (100-GHz ITU grid)
DWDM-SFP-3112 1000BASE-DWDM 1531.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-3190 1000BASE-DWDM 1531.90 nm SFP (100-GHz ITU grid)
DWDM-SFP-3268 1000BASE-DWDM 1532.68 nm SFP (100-GHz ITU grid)
DWDM-SFP-3425 1000BASE-DWDM 1534.25 nm SFP (100-GHz ITU grid)
DWDM-SFP-3504 1000BASE-DWDM 1535.04 nm SFP (100-GHz ITU grid)
DWDM-SFP-3582 1000BASE-DWDM 1535.82 nm SFP (100-GHz ITU grid)
DWDM-SFP-3661 1000BASE-DWDM 1536.61 nm SFP (100-GHz ITU grid)
DWDM-SFP-3819 1000BASE-DWDM 1538.19 nm SFP (100-GHz ITU grid)
DWDM-SFP-3898 1000BASE-DWDM 1538.98 nm SFP (100-GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-20G Line Card Overview
Table 2-36
Cisco 76-ES+T-20G Supported SFP Modules (continued)
Description
SFP Modules
DWDM-SFP-3977 1000BASE-DWDM 1539.77 nm SFP (100-GHz ITU grid)
DWDM-SFP-4056 1000BASE-DWDM 1540.56 nm SFP (100-GHz ITU grid)
DWDM-SFP-4214 1000BASE-DWDM 1542.14 nm SFP (100-GHz ITU grid)
DWDM-SFP-4294 1000BASE-DWDM 1542.94 nm SFP (100-GHz ITU grid)
DWDM-SFP-4373 1000BASE-DWDM 1543.73 nm SFP (100-GHz ITU grid)
DWDM-SFP-4453 1000BASE-DWDM 1544.53 nm SFP (100-GHz ITU grid)
DWDM-SFP-4612 1000BASE-DWDM 1546.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-4692 1000BASE-DWDM 1546.92 nm SFP (100-GHz ITU grid)
DWDM-SFP-4772 1000BASE-DWDM 1547.72 nm SFP (100-GHz ITU grid)
DWDM-SFP-4851 1000BASE-DWDM 1548.51 nm SFP (100-GHz ITU grid)
DWDM-SFP-5012 1000BASE-DWDM 1550.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-5092 1000BASE-DWDM 1550.92 nm SFP (100-GHz ITU grid)
DWDM-SFP-5172 1000BASE-DWDM 1551.72 nm SFP (100-GHz ITU grid)
DWDM-SFP-5252 1000BASE-DWDM 1552.52 nm SFP (100-GHz ITU grid)
DWDM-SFP-5413 1000BASE-DWDM 1554.13 nm SFP (100-GHz ITU grid)
DWDM-SFP-5494 1000BASE-DWDM 1554.94 nm SFP (100-GHz ITU grid)
DWDM-SFP-5575 1000BASE-DWDM 1555.75 nm SFP (100-GHz ITU grid)
DWDM-SFP-5655 1000BASE-DWDM 1556.55 nm SFP (100-GHz ITU grid)
DWDM-SFP-5817 1000BASE-DWDM 1558.17 nm SFP (100-GHz ITU grid)
DWDM-SFP-5898 1000BASE-DWDM 1558.98 nm SFP (100-GHz ITU grid)
DWDM-SFP-5979 1000BASE-DWDM 1559.79 nm SFP (100-GHz ITU grid)
DWDM-SFP-6061 1000BASE-DWDM 1560.61 nm SFP (100-GHz ITU grid)
DWDM-SFP-3346 DWDM SFP 1533.47 nm SFP (100 GHz ITU grid)
DWDM-SFP-3739 DWDM SFP 1537.40 nm SFP (100 GHz ITU grid)
DWDM-SFP-4134 DWDM SFP 1541.35 nm SFP (100 GHz ITU grid)
DWDM-SFP-4532 DWDM SFP 1545.32 nm SFP (100 GHz ITU grid)
DWDM-SFP-4931 DWDM SFP 1549.32 nm SFP (100 GHz ITU grid)
DWDM-SFP-5332 DWDM SFP 1553.33 nm SFP (100 GHz ITU grid)
DWDM-SFP-5736 DWDM SFP 1557.36 nm SFP (100 GHz ITU grid)
DWDM-SFP-6141 DWDM SFP 1561.42 nm SFP (100 GHz ITU grid)
SFPs are integrated fiber-optic transceivers that provide high-speed serial links from a port or slot to the
network. Various latching mechanisms can be used on the SFPs. There is no correlation between the type
of latch to the model type (such as SX or LX/LH) or technology type (such as Gigabit Ethernet). See the
label on the SFP for the technology type and model.
SFP dimensions are:
•
Height 0.03 in. (8.5 mm)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-20G Line Card Overview
•
•
Width 0.53 in. (13.4 mm)
Depth 2.22 in. (56.5 mm)
SFP temperature ranges are:
•
•
•
COM—Commercial operating temperature range -5 to 70 degrees C (23 to 158 degrees F)
EXT—Extended operating temperature range -5 to 85 degrees C (23 to 185 degrees F)
IND—Industrial operating temperature range -40 to 85 degrees C (-40 to 85 degrees F)
Figure 2-26 shows a typical SFP module.
Figure 2-26 SFP Optics Module
Connectors and Cabling
The SFP optical transceiver module on the Cisco 76-ES+T-20G line card require dual or single LC/PC
connectors. Only connections with patch cords with PC or UPC connectors are supported. Patch cords
with APC connectors are not supported. All cables and cable assemblies used must be compliant with
the standards specified below:
•
•
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable or
Figure 2-27
Duplex LC-Type Cable and Connector
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-40G Line Card Overview
For additional information on Cisco Transceiver Modules, see
Cisco 76-ES+T-40G Line Card Overview
The following sections describe the Cisco 76-ES+T-40G line cards:
•
•
•
•
•
•
Cisco 76-ES+T-40G Line Card Processors
Table 2-37
Cisco 76-ES+T-40G Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
control
processor
Cisco 76-ES+T-40G Line Card LEDs
The Cisco 76-ES+T-40G line cards have Status and A/L (Active Loopback) LEDs, as shown in
Figure 2-28
Cisco 76-ES+T-40G Line Card Faceplate
76-ES+T-40G
EXT CLK
STATUS
CLASS
LASER
1
ETHERNET SERVICES MODULE
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-40G Line Card Overview
Table 2-38
Cisco 76-ES+T-40G Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
Green
Yellow
Off
On
On
The line card is loading.
Off
On
The line card is powered off.
A/L
Amber
The port is enabled but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 76-ES+T-40G Physical Specifications
Table 2-39
Cisco 76-ES+T-40G Line Card Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 76-ES+T-40G line card occupies one module slot and can
be operated in all Cisco 7600 series routers except the Cisco 7603
router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 76-ES+T-40G Line Card Memory Options
Table 2-40 lists the memory options available for the Cisco 7600 ES+ 40G3C, -40G3CXL line cards:
Table 2-40
Cisco 7600 ES+ T-40G Line Card Memory Options
Line Card
Memory Options
2 GB
76-ES+T-40G
Cisco 76-ES+T-40G Supported SFP Modules
The Cisco 76-ES+T-40G line cards support the small form-factor pluggable (SFP) optical transceiver
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-40G Line Card Overview
Table 2-41
Cisco 76-ES+T-40G Supported SFP Modules
SFP Modules
SFP-GE-S
SFP-GE-L
SFP-GE-Z
SFP-GE-T
GLC-BX-D
GLC-BX-U
Description
1000BASE-SX short wavelength; with DOM
1000BASE-LX/LH short wavelength; with DOM
1000BASE-ZX; with DOM
1000BASE-T SFP
1000BASE-BX10-D downstream bidirectional single fiber; with DOM
1000BASE-BX10-U upstream bidirectional single fiber; with DOM
CWDM-SFP-1470 Cisco CWDM SFP 1470 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1490 Cisco CWDM SFP 1490 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1510 Cisco CWDM SFP 1510 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1530 Cisco CWDM SFP 1530 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1550 Cisco CWDM SFP 1550 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1570 Cisco CWDM SFP 1570 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1590 Cisco CWDM SFP 1590 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1610 Cisco CWDM SFP 1610 nm; Gigabit Ethernet and 1G/2G FC
DWDM-SFP-3033 1000BASE-DWDM 1530.33 nm SFP (100-GHz ITU grid)
DWDM-SFP-3112 1000BASE-DWDM 1531.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-3190 1000BASE-DWDM 1531.90 nm SFP (100-GHz ITU grid)
DWDM-SFP-3268 1000BASE-DWDM 1532.68 nm SFP (100-GHz ITU grid)
DWDM-SFP-3425 1000BASE-DWDM 1534.25 nm SFP (100-GHz ITU grid)
DWDM-SFP-3504 1000BASE-DWDM 1535.04 nm SFP (100-GHz ITU grid)
DWDM-SFP-3582 1000BASE-DWDM 1535.82 nm SFP (100-GHz ITU grid)
DWDM-SFP-3661 1000BASE-DWDM 1536.61 nm SFP (100-GHz ITU grid)
DWDM-SFP-3819 1000BASE-DWDM 1538.19 nm SFP (100-GHz ITU grid)
DWDM-SFP-3898 1000BASE-DWDM 1538.98 nm SFP (100-GHz ITU grid)
DWDM-SFP-3977 1000BASE-DWDM 1539.77 nm SFP (100-GHz ITU grid)
DWDM-SFP-4056 1000BASE-DWDM 1540.56 nm SFP (100-GHz ITU grid)
DWDM-SFP-4214 1000BASE-DWDM 1542.14 nm SFP (100-GHz ITU grid)
DWDM-SFP-4294 1000BASE-DWDM 1542.94 nm SFP (100-GHz ITU grid)
DWDM-SFP-4373 1000BASE-DWDM 1543.73 nm SFP (100-GHz ITU grid)
DWDM-SFP-4453 1000BASE-DWDM 1544.53 nm SFP (100-GHz ITU grid)
DWDM-SFP-4612 1000BASE-DWDM 1546.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-4692 1000BASE-DWDM 1546.92 nm SFP (100-GHz ITU grid)
DWDM-SFP-4772 1000BASE-DWDM 1547.72 nm SFP (100-GHz ITU grid)
DWDM-SFP-4851 1000BASE-DWDM 1548.51 nm SFP (100-GHz ITU grid)
DWDM-SFP-5012 1000BASE-DWDM 1550.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-5092 1000BASE-DWDM 1550.92 nm SFP (100-GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-40G Line Card Overview
Table 2-41
Cisco 76-ES+T-40G Supported SFP Modules (continued)
Description
SFP Modules
DWDM-SFP-5172 1000BASE-DWDM 1551.72 nm SFP (100-GHz ITU grid)
DWDM-SFP-5252 1000BASE-DWDM 1552.52 nm SFP (100-GHz ITU grid)
DWDM-SFP-5413 1000BASE-DWDM 1554.13 nm SFP (100-GHz ITU grid)
DWDM-SFP-5494 1000BASE-DWDM 1554.94 nm SFP (100-GHz ITU grid)
DWDM-SFP-5575 1000BASE-DWDM 1555.75 nm SFP (100-GHz ITU grid)
DWDM-SFP-5655 1000BASE-DWDM 1556.55 nm SFP (100-GHz ITU grid)
DWDM-SFP-5817 1000BASE-DWDM 1558.17 nm SFP (100-GHz ITU grid)
DWDM-SFP-5898 1000BASE-DWDM 1558.98 nm SFP (100-GHz ITU grid)
DWDM-SFP-5979 1000BASE-DWDM 1559.79 nm SFP (100-GHz ITU grid)
DWDM-SFP-6061 1000BASE-DWDM 1560.61 nm SFP (100-GHz ITU grid)
DWDM-SFP-3346 DWDM SFP 1533.47 nm SFP (100 GHz ITU grid)
DWDM-SFP-3739 DWDM SFP 1537.40 nm SFP (100 GHz ITU grid)
DWDM-SFP-4134 DWDM SFP 1541.35 nm SFP (100 GHz ITU grid)
DWDM-SFP-4532 DWDM SFP 1545.32 nm SFP (100 GHz ITU grid)
DWDM-SFP-4931 DWDM SFP 1549.32 nm SFP (100 GHz ITU grid)
DWDM-SFP-5332 DWDM SFP 1553.33 nm SFP (100 GHz ITU grid)
DWDM-SFP-5736 DWDM SFP 1557.36 nm SFP (100 GHz ITU grid)
DWDM-SFP-6141 DWDM SFP 1561.42 nm SFP (100 GHz ITU grid)
SFPs are integrated fiber-optic transceivers that provide high-speed serial links from a port or slot to the
network. Various latching mechanisms can be used on the SFPs. There is no correlation between the type
of latch to the model type (such as SX or LX/LH) or technology type (such as Gigabit Ethernet). See the
label on the SFP for the technology type and model.
SFP dimensions are:
•
•
•
Height 0.03 in. (8.5 mm)
Width 0.53 in. (13.4 mm)
Depth 2.22 in. (56.5 mm)
SFP temperature ranges are:
•
•
•
COM—Commercial operating temperature range -5 to 70 degrees C (23 to 158 degrees F)
EXT—Extended operating temperature range -5 to 85 degrees C (23 to 185 degrees F)
IND—Industrial operating temperature range -40 to 85 degrees C (-40 to 85 degrees F)
Figure 2-29 shows a typical SFP module.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-2TG Line Card Overview
Figure 2-29
SFP Optics Module
Connectors and Cabling
The SFP optical transceiver module on the Cisco 76-ES+T-40G line card requires dual or single LC/PC
connectors. Only connections with patch cords with PC or UPC connectors are supported. Patch cords
with APC connectors are not supported. All cables and cable assemblies used must be compliant with
the standards specified below:
•
•
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable or
Figure 2-30
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 76-ES+T-2TG Line Card Overview
The following sections describe the Cisco 76-ES+T-2TG line cards:
•
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-2TG Line Card Overview
•
•
•
•
Cisco 76-ES+T-2TG Line Card Processors
Table 2-42
Cisco 76-ES+T-2TG Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
control
processor
Cisco 76-ES+T-2TG Line Card LEDs
The Cisco 76-ES+T-2TG line cards have Status and A/L (Active Loopback) LEDs, as shown in
Figure 2-31
Cisco 76-ES+T-2TG Line Card Faceplate
76-ES+T-2TG
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Table 2-43 provides LED descriptions.
Table 2-43
Cisco 76-ES+T-2TG Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-2TG Line Card Overview
Cisco 76-ES+T-2TG Physical Specifications
Table 2-44
Cisco 76-ES+T-2TG Line Card Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 76-ES+T-2TG line card occupies one module slot and can
be operated in all Cisco 7600 series routers except the Cisco 7603
router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 76-ES+T-2TG Line Card Memory Options
Table 2-45 lists the memory options available for the Cisco 76-ES+T-2TG line cards:
Table 2-45
Cisco 76-ES+T-2TGCXL Line Card Memory Options
Line Card
Memory Options
2 GB
Cisco 76-ES+T-2TG
Cisco 76-ES+T-2TG Supported XFP Modules
Table 2-46 Cisco 76-ES+T-2TG Supported XFP Modules
XFP
Description
XFP-10GLR-OC192SR
Cisco Multirate 10GBASE-LR and OC-192/STM-64 SR-1 XFP
Module for SMF
XFP-10GZR-OC192LR
XFP-10GER-192IR+
Cisco Multirate 10GBASE-ZR and OC-192/STM-64 lR-2 XFP
Module for SMF
Cisco Multirate 10GBASE-ER and OC-192/STM-64 IR-2 XFP
Module for SMF
XFP-10GLR-OC192SR-L
XFP-10GLR-OC192IR-L
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
DWDM-XFP-60.61
DWDM-XFP-59.79
DWDM-XFP-58.98
DWDM XFP 1560.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1559.79 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.98 nm XFP (100 GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-2TG Line Card Overview
Table 2-46 Cisco 76-ES+T-2TG Supported XFP Modules (continued)
XFP
Description
DWDM-XFP-58.17
DWDM-XFP-56.55
DWDM-XFP-55.75
DWDM-XFP-54.94
DWDM-XFP-54.13
DWDM-XFP-52.52
DWDM-XFP-51.72
DWDM-XFP-50.92
DWDM-XFP-50.12
DWDM-XFP-48.51
DWDM-XFP-47.72
DWDM-XFP-46.92
DWDM-XFP-46.12
DWDM-XFP-44.53
DWDM-XFP-43.73
DWDM-XFP-42.94
DWDM-XFP-42.14
DWDM-XFP-40.56
DWDM-XFP-39.77
DWDM-XFP-38.98
DWDM-XFP-38.19
DWDM-XFP-36.61
DWDM-XFP-35.82
DWDM-XFP-35.04
DWDM-XFP-34.25
DWDM-XFP-32.68
DWDM-XFP-31.90
DWDM-XFP-31.12
DWDM-XFP-30.33
DWDM XFP 1558.17 nm XFP (100 GHz ITU grid)
DWDM XFP 1556.55 nm XFP (100 GHz ITU grid)
DWDM XFP 1555.75 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.13 nm XFP (100 GHz ITU grid)
DWDM XFP 1552.52 nm XFP (100 GHz ITU grid)
DWDM XFP 1551.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1548.51 nm XFP (100 GHz ITU grid)
DWDM XFP 1547.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1544.53 nm XFP (100 GHz ITU grid)
DWDM XFP 1543.73 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.14 nm XFP (100 GHz ITU grid)
DWDM XFP 1540.56 nm XFP (100 GHz ITU grid)
DWDM XFP 1539.77 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.19 nm XFP (100 GHz ITU grid)
DWDM XFP 1536.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.82 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.04 nm XFP (100 GHz ITU grid)
DWDM XFP 1534.25 nm XFP (100 GHz ITU grid)
DWDM XFP 1532.68 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.90 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1530.33 nm XFP (100 GHz ITU grid)
The XFP modules provide high-speed serial links at the following rates: 9.95 Gbps (OC-192) and
10.3125 Gbps (10 Gigabit Ethernet) on single-mode fiber (SMF). The transmit side recovers and retimes
the 10-Gbps serial data and passes it to a laser driver. The laser driver biases and modulates a 1310-nm
or 1550-nm laser, enabling data transmission over SMF through an LC connector. The receive side
recovers and retimes the 10-Gbps optical data stream from a photo-detector transimpedance amplifier
and passes it to an output driver.
See the label on the XFP module for technology type and model.
XFP module dimensions are:
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-2TG Line Card Overview
•
•
•
Height: 12.5 mm
Width: 18.35 mm
Length: 71.1mm
Figure 2-32 XFP Module
Connectors and Cabling
The XFP optical transceiver module on the Cisco 76-ES+T-2TG line card requires dual LC/PC
connectors. Only connections with patch cords with PC or UPC connectors are supported. Patch cords
with APC connectors are not supported. All cables and cable assemblies used must be compliant with
the standards specified below:
•
•
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
Figure 2-33 shows the cable type for use with the XFP optical transceiver module on the Cisco
76-ES+T-2TG card.
Figure 2-33
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-4TG Line Card Overview
Cisco 76-ES+T-4TG Line Card Overview
The following sections describe the Cisco 76-ES+T-4TG line cards:
•
•
•
•
•
Cisco 76-ES+T-4TG Line Card Processors
Table 2-47
Cisco 76-ES+T-4TG Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
control
processor
Cisco 76-ES+T-4TG Line Card LEDs
The Cisco 76-ES+T-4TG line cards have Status and A/L (Active Loopback) LEDs, as shown in
Figure 2-34
Cisco 76-ES+T-4TG Line Card Faceplate
76-ES+T-4TG
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Table 2-48 provides LED descriptions.
Table 2-48
Cisco 76-ES+T-4TG Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-4TG Line Card Overview
Table 2-48
Cisco 76-ES+T-4TG Line Card LEDs (continued)
LED Label
Color
State
Meaning
A/L
Amber
On
The port is enabled but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 76-ES+T-4TG Physical Specifications
Table 2-49
Cisco 76-ES+T-4TG Line Card Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 76-ES+T-4TG line card occupies one module slot and can
be operated in all Cisco 7600 series routers except the Cisco 7603
router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 76-ES+T-4TG Line Card Memory Options
Table 2-50 lists the memory options available for the Cisco 76-ES+T-4TG line cards:
Table 2-50
Cisco 76-ES+T-4TG Line Card Memory Options
Line Card
Memory Options
2 GB
Cisco 76-ES+T-4TG
Cisco 76-ES+T-4TG Supported XFP Modules
Table 2-51 Cisco 76-ES+T-4TG Supported XFP Modules
XFP
Description
XFP-10GLR-OC192SR
Cisco Multirate 10GBASE-LR and OC-192/STM-64 SR-1 XFP
Module for SMF
XFP-10GZR-OC192LR
Cisco Multirate 10GBASE-ZR and OC-192/STM-64 lR-2 XFP
Module for SMF
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-4TG Line Card Overview
Table 2-51 Cisco 76-ES+T-4TG Supported XFP Modules (continued)
XFP
Description
XFP-10GER-192IR+
Cisco Multirate 10GBASE-ER and OC-192/STM-64 IR-2 XFP
Module for SMF
XFP-10GLR-OC192SR-L
XFP-10GLR-OC192IR-L
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
DWDM-XFP-60.61
DWDM-XFP-59.79
DWDM-XFP-58.98
DWDM-XFP-58.17
DWDM-XFP-56.55
DWDM-XFP-55.75
DWDM-XFP-54.94
DWDM-XFP-54.13
DWDM-XFP-52.52
DWDM-XFP-51.72
DWDM-XFP-50.92
DWDM-XFP-50.12
DWDM-XFP-48.51
DWDM-XFP-47.72
DWDM-XFP-46.92
DWDM-XFP-46.12
DWDM-XFP-44.53
DWDM-XFP-43.73
DWDM-XFP-42.94
DWDM-XFP-42.14
DWDM-XFP-40.56
DWDM-XFP-39.77
DWDM-XFP-38.98
DWDM-XFP-38.19
DWDM-XFP-36.61
DWDM-XFP-35.82
DWDM-XFP-35.04
DWDM-XFP-34.25
DWDM-XFP-32.68
DWDM-XFP-31.90
DWDM XFP 1560.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1559.79 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.17 nm XFP (100 GHz ITU grid)
DWDM XFP 1556.55 nm XFP (100 GHz ITU grid)
DWDM XFP 1555.75 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.13 nm XFP (100 GHz ITU grid)
DWDM XFP 1552.52 nm XFP (100 GHz ITU grid)
DWDM XFP 1551.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1548.51 nm XFP (100 GHz ITU grid)
DWDM XFP 1547.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1544.53 nm XFP (100 GHz ITU grid)
DWDM XFP 1543.73 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.14 nm XFP (100 GHz ITU grid)
DWDM XFP 1540.56 nm XFP (100 GHz ITU grid)
DWDM XFP 1539.77 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.19 nm XFP (100 GHz ITU grid)
DWDM XFP 1536.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.82 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.04 nm XFP (100 GHz ITU grid)
DWDM XFP 1534.25 nm XFP (100 GHz ITU grid)
DWDM XFP 1532.68 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.90 nm XFP (100 GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-4TG Line Card Overview
Table 2-51 Cisco 76-ES+T-4TG Supported XFP Modules (continued)
XFP
Description
DWDM-XFP-31.12
DWDM-XFP-30.33
DWDM XFP 1531.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1530.33 nm XFP (100 GHz ITU grid)
The XFP modules provide high-speed serial links at the following rates: 9.95 Gbps (OC-192) and
10.3125 Gbps (10 Gigabit Ethernet) on single-mode fiber (SMF). The transmit side recovers and retimes
the 10-Gbps serial data and passes it to a laser driver. The laser driver biases and modulates a 1310-nm
or 1550-nm laser, enabling data transmission over SMF through an LC connector. The receive side
recovers and retimes the 10-Gbps optical data stream from a photo-detector transimpedance amplifier
and passes it to an output driver.
See the label on the XFP module for technology type and model.
XFP module dimensions are:
•
•
•
Height: 12.5 mm
Width: 18.35 mm
Length: 71.1mm
Figure 2-35 XFP Module
Connectors and Cabling
The XFP optical transceiver module on the Cisco 76-ES+T-4TG line card requires dual LC/PC
connectors. Only connections with patch cords with PC or UPC connectors are supported. Patch cords
with APC connectors are not supported. All cables and cable assemblies used must be compliant with
the standards specified below:
•
•
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
Figure 2-36 shows the cable type for use with the XFP optical transceiver module on the Cisco
76-ES+T-4TG line card.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-4TG Line Card Overview
Figure 2-36
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card Overview
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card Overview
The following sections describe the Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL line cards:
•
•
•
•
•
•
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card Processors
The processors on the Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL line cards are listed in
Table 2-52
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
control
processor
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card LEDs
The Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL line cards have Status and A/L (Active Loopback)
Figure 2-37
76-ES+XC-20G3C
Cisco 76-ES+XC-20G3C Line Card Faceplate
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Figure 2-38
76-ES+XC-20G3CXL
Cisco 76-ES+XC-20G3CXL Line Card Faceplate
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-52
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card Overview
Table 2-53 provides LED descriptions.
Table 2-53
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Physical Specifications
The Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL line card physical specifications are shown in
Table 2-54
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL line cards
occupy one module slot and can be operated in all Cisco 7600 series
routers except the Cisco 7603 router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card Memory Options
Table 2-55 lists the memory options available for the Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL
line cards:
Table 2-55
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card Memory Options
Line Card
Memory Options
Cisco 76-ES+XC-20G3C
1 GB
2 GB
Cisco 76-ES+XC-20G3CXL
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card Overview
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Supported SFP Modules
The Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL line cards support the small form-factor pluggable
(SFP) optical transceiver modules listed in Table 2-56
Table 2-56
Cisco 7600-76-ES+XC-20G3C, 76-ES+XC-20G3CXL Supported SFP Modules
SFP Modules
SFP-GE-S
SFP-GE-L
SFP-GE-Z
SFP-GE-T
GLC-BX-D
GLC-BX-U
Description
1000BASE-SX short wavelength; with DOM
1000BASE-LX/LH short wavelength; with DOM
1000BASE-ZX; with DOM
1000BASE-T SFP
1000BASE-BX10-D downstream bidirectional single fiber; with DOM
1000BASE-BX10-U upstream bidirectional single fiber; with DOM
CWDM-SFP-1470 Cisco CWDM SFP 1470 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1490 Cisco CWDM SFP 1490 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1510 Cisco CWDM SFP 1510 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1530 Cisco CWDM SFP 1530 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1550 Cisco CWDM SFP 1550 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1570 Cisco CWDM SFP 1570 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1590 Cisco CWDM SFP 1590 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1610 Cisco CWDM SFP 1610 nm; Gigabit Ethernet and 1G/2G FC
DWDM-SFP-3033 1000BASE-DWDM 1530.33 nm SFP (100-GHz ITU grid)
DWDM-SFP-3112 1000BASE-DWDM 1531.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-3190 1000BASE-DWDM 1531.90 nm SFP (100-GHz ITU grid)
DWDM-SFP-3268 1000BASE-DWDM 1532.68 nm SFP (100-GHz ITU grid)
DWDM-SFP-3425 1000BASE-DWDM 1534.25 nm SFP (100-GHz ITU grid)
DWDM-SFP-3504 1000BASE-DWDM 1535.04 nm SFP (100-GHz ITU grid)
DWDM-SFP-3582 1000BASE-DWDM 1535.82 nm SFP (100-GHz ITU grid)
DWDM-SFP-3661 1000BASE-DWDM 1536.61 nm SFP (100-GHz ITU grid)
DWDM-SFP-3819 1000BASE-DWDM 1538.19 nm SFP (100-GHz ITU grid)
DWDM-SFP-3898 1000BASE-DWDM 1538.98 nm SFP (100-GHz ITU grid)
DWDM-SFP-3977 1000BASE-DWDM 1539.77 nm SFP (100-GHz ITU grid)
DWDM-SFP-4056 1000BASE-DWDM 1540.56 nm SFP (100-GHz ITU grid)
DWDM-SFP-4214 1000BASE-DWDM 1542.14 nm SFP (100-GHz ITU grid)
DWDM-SFP-4294 1000BASE-DWDM 1542.94 nm SFP (100-GHz ITU grid)
DWDM-SFP-4373 1000BASE-DWDM 1543.73 nm SFP (100-GHz ITU grid)
DWDM-SFP-4453 1000BASE-DWDM 1544.53 nm SFP (100-GHz ITU grid)
DWDM-SFP-4612 1000BASE-DWDM 1546.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-4692 1000BASE-DWDM 1546.92 nm SFP (100-GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-54
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card Overview
Table 2-56
Cisco 7600-76-ES+XC-20G3C, 76-ES+XC-20G3CXL Supported SFP Modules
SFP Modules
Description
DWDM-SFP-4772 1000BASE-DWDM 1547.72 nm SFP (100-GHz ITU grid)
DWDM-SFP-4851 1000BASE-DWDM 1548.51 nm SFP (100-GHz ITU grid)
DWDM-SFP-5012 1000BASE-DWDM 1550.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-5092 1000BASE-DWDM 1550.92 nm SFP (100-GHz ITU grid)
DWDM-SFP-5172 1000BASE-DWDM 1551.72 nm SFP (100-GHz ITU grid)
DWDM-SFP-5252 1000BASE-DWDM 1552.52 nm SFP (100-GHz ITU grid)
DWDM-SFP-5413 1000BASE-DWDM 1554.13 nm SFP (100-GHz ITU grid)
DWDM-SFP-5494 1000BASE-DWDM 1554.94 nm SFP (100-GHz ITU grid)
DWDM-SFP-5575 1000BASE-DWDM 1555.75 nm SFP (100-GHz ITU grid)
DWDM-SFP-5655 1000BASE-DWDM 1556.55 nm SFP (100-GHz ITU grid)
DWDM-SFP-5817 1000BASE-DWDM 1558.17 nm SFP (100-GHz ITU grid)
DWDM-SFP-5898 1000BASE-DWDM 1558.98 nm SFP (100-GHz ITU grid)
DWDM-SFP-5979 1000BASE-DWDM 1559.79 nm SFP (100-GHz ITU grid)
DWDM-SFP-6061 1000BASE-DWDM 1560.61 nm SFP (100-GHz ITU grid)
DWDM-SFP-3346 DWDM SFP 1533.47 nm SFP (100 GHz ITU grid)
DWDM-SFP-3739 DWDM SFP 1537.40 nm SFP (100 GHz ITU grid)
DWDM-SFP-4134 DWDM SFP 1541.35 nm SFP (100 GHz ITU grid)
DWDM-SFP-4532 DWDM SFP 1545.32 nm SFP (100 GHz ITU grid)
DWDM-SFP-4931 DWDM SFP 1549.32 nm SFP (100 GHz ITU grid)
DWDM-SFP-5332 DWDM SFP 1553.33 nm SFP (100 GHz ITU grid)
DWDM-SFP-5736 DWDM SFP 1557.36 nm SFP (100 GHz ITU grid)
DWDM-SFP-6141 DWDM SFP 1561.42 nm SFP (100 GHz ITU grid)
SFPs are integrated fiber-optic transceivers that provide high-speed serial links from a port or slot to the
network. Various latching mechanisms can be used on the SFPs. There is no correlation between the type
of latch to the model type (such as SX or LX/LH) or technology type (such as Gigabit Ethernet). See the
label on the SFP for the technology type and model.
SFP dimensions are:
•
•
•
Height 0.03 in. (8.5 mm)
Width 0.53 in. (13.4 mm)
Depth 2.22 in. (56.5 mm)
SFP temperature ranges are:
•
•
•
COM—Commercial operating temperature range -5 to 70 degrees C (23 to 158 degrees F)
EXT—Extended operating temperature range -5 to 85 degrees C (23 to 185 degrees F)
IND—Industrial operating temperature range -40 to 85 degrees C (-40 to 85 degrees F)
Figure 2-39 shows a typical SFP module.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card Overview
Figure 2-39
SFP Optics Module
Connectors and Cabling
The SFP optical transceiver module on the Cisco 7600-ES+20G3C, -3CXL line card require dual or
single LC/PC connectors. Only connections with patch cords with PC or UPC connectors are supported.
Patch cords with APC connectors are not supported. All cables and cable assemblies used must be
compliant with the standards specified below:
•
•
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable or
Figure 2-40
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Supported XFP Modules
The Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL line card supports the XFP modules listed in
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card Overview
Table 2-57 Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Supported XFP Modules
XFP
Description
XFP-10GLR-OC192SR
Cisco Multirate 10GBASE-LR and OC-192/STM-64 SR-1 XFP
Module for SMF
XFP-10GZR-OC192LR
XFP-10GER-192IR+
Cisco Multirate 10GBASE-ZR and OC-192/STM-64 lR-2 XFP
Module for SMF
Cisco Multirate 10GBASE-ER and OC-192/STM-64 IR-2 XFP
Module for SMF
XFP-10GLR-OC192SR-L
XFP-10GLR-OC192IR-L
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
DWDM-XFP-60.61
DWDM-XFP-59.79
DWDM-XFP-58.98
DWDM-XFP-58.17
DWDM-XFP-56.55
DWDM-XFP-55.75
DWDM-XFP-54.94
DWDM-XFP-54.13
DWDM-XFP-52.52
DWDM-XFP-51.72
DWDM-XFP-50.92
DWDM-XFP-50.12
DWDM-XFP-48.51
DWDM-XFP-47.72
DWDM-XFP-46.92
DWDM-XFP-46.12
DWDM-XFP-44.53
DWDM-XFP-43.73
DWDM-XFP-42.94
DWDM-XFP-42.14
DWDM-XFP-40.56
DWDM-XFP-39.77
DWDM-XFP-38.98
DWDM-XFP-38.19
DWDM-XFP-36.61
DWDM-XFP-35.82
DWDM-XFP-35.04
DWDM XFP 1560.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1559.79 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.17 nm XFP (100 GHz ITU grid)
DWDM XFP 1556.55 nm XFP (100 GHz ITU grid)
DWDM XFP 1555.75 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.13 nm XFP (100 GHz ITU grid)
DWDM XFP 1552.52 nm XFP (100 GHz ITU grid)
DWDM XFP 1551.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1548.51 nm XFP (100 GHz ITU grid)
DWDM XFP 1547.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1544.53 nm XFP (100 GHz ITU grid)
DWDM XFP 1543.73 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.14 nm XFP (100 GHz ITU grid)
DWDM XFP 1540.56 nm XFP (100 GHz ITU grid)
DWDM XFP 1539.77 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.19 nm XFP (100 GHz ITU grid)
DWDM XFP 1536.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.82 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.04 nm XFP (100 GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-57
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Line Card Overview
Table 2-57 Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL Supported XFP Modules (continued)
XFP
Description
DWDM-XFP-34.25
DWDM-XFP-32.68
DWDM-XFP-31.90
DWDM-XFP-31.12
DWDM-XFP-30.33
DWDM XFP 1534.25 nm XFP (100 GHz ITU grid)
DWDM XFP 1532.68 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.90 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1530.33 nm XFP (100 GHz ITU grid)
The XFP modules provide high-speed serial links at the following rates: 9.95 Gbps (OC-192) and
10.3125 Gbps (10 Gigabit Ethernet) on single-mode fiber (SMF). The transmit side recovers and retimes
the 10-Gbps serial data and passes it to a laser driver. The laser driver biases and modulates a 1310-nm
or 1550-nm laser, enabling data transmission over SMF through an LC connector. The receive side
recovers and retimes the 10-Gbps optical data stream from a photo-detector transimpedance amplifier
and passes it to an output driver.
See the label on the XFP module for technology type and model.
XFP module dimensions are:
•
•
•
Height: 12.5 mm
Width: 18.35 mm
Length: 71.1mm
Figure 2-41 XFP Module
Connectors and Cabling
The XFP optical transceiver module on the Cisco 76-ES+XC-20G3C, 76-ES+XC-20G3CXL line card
require dual LC/PC connectors. Only connections with patch cords with PC or UPC connectors are
supported. Patch cords with APC connectors are not supported. All cables and cable assemblies used
must be compliant with the standards specified below:
•
•
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
Figure 2-42 shows the cable type for use with the XFP optical transceiver module on the Cisco
76-ES+XC-20G3C, 76-ES+XC-20G3CXL line card.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-58
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card Overview
Figure 2-42
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card Overview
The following sections describe the Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL line cards:
•
•
•
•
•
•
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card Processors
The processors on the Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL line cards are listed in
Table 2-58
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
control
processor
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card LEDs
The Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL line cards have Status and A/L (Active Loopback)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-59
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card Overview
Figure 2-43
76-ES+XC-40G3C
Cisco 76-ES+XC-40G3C Line Card Faceplate
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Figure 2-44
76-ES+XC-40G3CXL
Cisco 76-ES+XC-40G3CXL Line Card Faceplate
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Table 2-59 provides LED descriptions.
Table 2-59
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Physical Specifications
The Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL line card physical specifications are shown in
Table 2-60
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL line cards
occupy one module slot and can be operated in all Cisco 7600 series
routers except the Cisco 7603 router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-60
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card Overview
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card Memory Options
Table 2-61 lists the memory options available for the Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL
line cards:
Table 2-61
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card Memory Options
Line Card
Memory Options
Cisco 76-ES+XC-40G3C
1 GB
2 GB
Cisco 76-ES+XC-40G3CXL
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Supported SFP Modules
The Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL line cards support the small form-factor pluggable
(SFP) optical transceiver modules listed in Table 2-62
Table 2-62
Cisco 7600-76-ES+XC-40G3C, 76-ES+XC-40G3CXL Supported SFP Modules
SFP Modules
SFP-GE-S
SFP-GE-L
SFP-GE-Z
SFP-GE-T
GLC-BX-D
GLC-BX-U
Description
1000BASE-SX short wavelength; with DOM
1000BASE-LX/LH short wavelength; with DOM
1000BASE-ZX; with DOM
1000BASE-T SFP
1000BASE-BX10-D downstream bidirectional single fiber; with DOM
1000BASE-BX10-U upstream bidirectional single fiber; with DOM
CWDM-SFP-1470 Cisco CWDM SFP 1470 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1490 Cisco CWDM SFP 1490 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1510 Cisco CWDM SFP 1510 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1530 Cisco CWDM SFP 1530 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1550 Cisco CWDM SFP 1550 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1570 Cisco CWDM SFP 1570 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1590 Cisco CWDM SFP 1590 nm; Gigabit Ethernet and 1G/2G FC
CWDM-SFP-1610 Cisco CWDM SFP 1610 nm; Gigabit Ethernet and 1G/2G FC
DWDM-SFP-3033 1000BASE-DWDM 1530.33 nm SFP (100-GHz ITU grid)
DWDM-SFP-3112 1000BASE-DWDM 1531.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-3190 1000BASE-DWDM 1531.90 nm SFP (100-GHz ITU grid)
DWDM-SFP-3268 1000BASE-DWDM 1532.68 nm SFP (100-GHz ITU grid)
DWDM-SFP-3425 1000BASE-DWDM 1534.25 nm SFP (100-GHz ITU grid)
DWDM-SFP-3504 1000BASE-DWDM 1535.04 nm SFP (100-GHz ITU grid)
DWDM-SFP-3582 1000BASE-DWDM 1535.82 nm SFP (100-GHz ITU grid)
DWDM-SFP-3661 1000BASE-DWDM 1536.61 nm SFP (100-GHz ITU grid)
DWDM-SFP-3819 1000BASE-DWDM 1538.19 nm SFP (100-GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card Overview
Table 2-62
Cisco 7600-76-ES+XC-40G3C, 76-ES+XC-40G3CXL Supported SFP Modules
SFP Modules
Description
DWDM-SFP-3898 1000BASE-DWDM 1538.98 nm SFP (100-GHz ITU grid)
DWDM-SFP-3977 1000BASE-DWDM 1539.77 nm SFP (100-GHz ITU grid)
DWDM-SFP-4056 1000BASE-DWDM 1540.56 nm SFP (100-GHz ITU grid)
DWDM-SFP-4214 1000BASE-DWDM 1542.14 nm SFP (100-GHz ITU grid)
DWDM-SFP-4294 1000BASE-DWDM 1542.94 nm SFP (100-GHz ITU grid)
DWDM-SFP-4373 1000BASE-DWDM 1543.73 nm SFP (100-GHz ITU grid)
DWDM-SFP-4453 1000BASE-DWDM 1544.53 nm SFP (100-GHz ITU grid)
DWDM-SFP-4612 1000BASE-DWDM 1546.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-4692 1000BASE-DWDM 1546.92 nm SFP (100-GHz ITU grid)
DWDM-SFP-4772 1000BASE-DWDM 1547.72 nm SFP (100-GHz ITU grid)
DWDM-SFP-4851 1000BASE-DWDM 1548.51 nm SFP (100-GHz ITU grid)
DWDM-SFP-5012 1000BASE-DWDM 1550.12 nm SFP (100-GHz ITU grid)
DWDM-SFP-5092 1000BASE-DWDM 1550.92 nm SFP (100-GHz ITU grid)
DWDM-SFP-5172 1000BASE-DWDM 1551.72 nm SFP (100-GHz ITU grid)
DWDM-SFP-5252 1000BASE-DWDM 1552.52 nm SFP (100-GHz ITU grid)
DWDM-SFP-5413 1000BASE-DWDM 1554.13 nm SFP (100-GHz ITU grid)
DWDM-SFP-5494 1000BASE-DWDM 1554.94 nm SFP (100-GHz ITU grid)
DWDM-SFP-5575 1000BASE-DWDM 1555.75 nm SFP (100-GHz ITU grid)
DWDM-SFP-5655 1000BASE-DWDM 1556.55 nm SFP (100-GHz ITU grid)
DWDM-SFP-5817 1000BASE-DWDM 1558.17 nm SFP (100-GHz ITU grid)
DWDM-SFP-5898 1000BASE-DWDM 1558.98 nm SFP (100-GHz ITU grid)
DWDM-SFP-5979 1000BASE-DWDM 1559.79 nm SFP (100-GHz ITU grid)
DWDM-SFP-6061 1000BASE-DWDM 1560.61 nm SFP (100-GHz ITU grid)
DWDM-SFP-3346 DWDM SFP 1533.47 nm SFP (100 GHz ITU grid)
DWDM-SFP-3739 DWDM SFP 1537.40 nm SFP (100 GHz ITU grid)
DWDM-SFP-4134 DWDM SFP 1541.35 nm SFP (100 GHz ITU grid)
DWDM-SFP-4532 DWDM SFP 1545.32 nm SFP (100 GHz ITU grid)
DWDM-SFP-4931 DWDM SFP 1549.32 nm SFP (100 GHz ITU grid)
DWDM-SFP-5332 DWDM SFP 1553.33 nm SFP (100 GHz ITU grid)
DWDM-SFP-5736 DWDM SFP 1557.36 nm SFP (100 GHz ITU grid)
DWDM-SFP-6141 DWDM SFP 1561.42 nm SFP (100 GHz ITU grid)
SFPs are integrated fiber-optic transceivers that provide high-speed serial links from a port or slot to the
network. Various latching mechanisms can be used on the SFPs. There is no correlation between the type
of latch to the model type (such as SX or LX/LH) or technology type (such as Gigabit Ethernet). See the
label on the SFP for the technology type and model.
SFP dimensions are:
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-62
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card Overview
•
•
•
Height 0.03 in. (8.5 mm)
Width 0.53 in. (13.4 mm)
Depth 2.22 in. (56.5 mm)
SFP temperature ranges are:
•
•
•
COM—Commercial operating temperature range -5 to 70 degrees C (23 to 158 degrees F)
EXT—Extended operating temperature range -5 to 85 degrees C (23 to 185 degrees F)
IND—Industrial operating temperature range -40 to 85 degrees C (-40 to 85 degrees F)
Figure 2-45 shows a typical SFP module.
Figure 2-45 SFP Optics Module
Connectors and Cabling
The SFP optical transceiver module on the Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL line card
require dual or single LC/PC connectors. Only connections with patch cords with PC or UPC connectors
are supported. Patch cords with APC connectors are not supported. All cables and cable assemblies used
must be compliant with the standards specified below:
•
•
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable or
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-63
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card Overview
Figure 2-46
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Supported XFP Modules
The Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL line card supports the XFP modules listed in
Table 2-63 Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Supported XFP Modules
XFP
Description
XFP-10GLR-OC192SR
Cisco Multirate 10GBASE-LR and OC-192/STM-64 SR-1 XFP
Module for SMF
XFP-10GZR-OC192LR
XFP-10GER-192IR+
Cisco Multirate 10GBASE-ZR and OC-192/STM-64 lR-2 XFP
Module for SMF
Cisco Multirate 10GBASE-ER and OC-192/STM-64 IR-2 XFP
Module for SMF
XFP-10GLR-OC192SR-L
XFP-10GLR-OC192IR-L
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
DWDM-XFP-60.61
DWDM-XFP-59.79
DWDM-XFP-58.98
DWDM-XFP-58.17
DWDM-XFP-56.55
DWDM-XFP-55.75
DWDM-XFP-54.94
DWDM-XFP-54.13
DWDM-XFP-52.52
DWDM-XFP-51.72
DWDM-XFP-50.92
DWDM-XFP-50.12
DWDM-XFP-48.51
DWDM XFP 1560.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1559.79 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.17 nm XFP (100 GHz ITU grid)
DWDM XFP 1556.55 nm XFP (100 GHz ITU grid)
DWDM XFP 1555.75 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.13 nm XFP (100 GHz ITU grid)
DWDM XFP 1552.52 nm XFP (100 GHz ITU grid)
DWDM XFP 1551.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1548.51 nm XFP (100 GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-64
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Line Card Overview
Table 2-63 Cisco 76-ES+XC-40G3C, 76-ES+XC-40G3CXL Supported XFP Modules (continued)
XFP
Description
DWDM-XFP-47.72
DWDM-XFP-46.92
DWDM-XFP-46.12
DWDM-XFP-44.53
DWDM-XFP-43.73
DWDM-XFP-42.94
DWDM-XFP-42.14
DWDM-XFP-40.56
DWDM-XFP-39.77
DWDM-XFP-38.98
DWDM-XFP-38.19
DWDM-XFP-36.61
DWDM-XFP-35.82
DWDM-XFP-35.04
DWDM-XFP-34.25
DWDM-XFP-32.68
DWDM-XFP-31.90
DWDM-XFP-31.12
DWDM-XFP-30.33
DWDM XFP 1547.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1544.53 nm XFP (100 GHz ITU grid)
DWDM XFP 1543.73 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.14 nm XFP (100 GHz ITU grid)
DWDM XFP 1540.56 nm XFP (100 GHz ITU grid)
DWDM XFP 1539.77 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.19 nm XFP (100 GHz ITU grid)
DWDM XFP 1536.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.82 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.04 nm XFP (100 GHz ITU grid)
DWDM XFP 1534.25 nm XFP (100 GHz ITU grid)
DWDM XFP 1532.68 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.90 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1530.33 nm XFP (100 GHz ITU grid)
The XFP modules provide high-speed serial links at the following rates: 9.95 Gbps (OC-192) and
10.3125 Gbps (10 Gigabit Ethernet) on single-mode fiber (SMF). The transmit side recovers and retimes
the 10-Gbps serial data and passes it to a laser driver. The laser driver biases and modulates a 1310-nm
or 1550-nm laser, enabling data transmission over SMF through an LC connector. The receive side
recovers and retimes the 10-Gbps optical data stream from a photo-detector transimpedance amplifier
and passes it to an output driver.
See the label on the XFP module for technology type and model.
XFP module dimensions are:
•
•
•
Height: 12.5 mm
Width: 18.35 mm
Length: 71.1mm
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-65
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T+XC-20G Line Card Overview
Figure 2-47
XFP Module
Connectors and Cabling
The XFP optical transceiver module on the Cisco 7600 ES+ 2TG3C, 7600 ES+ 2TG3CXL line card
require dual LC/PC connectors. Only connections with patch cords with PC or UPC connectors are
supported. Patch cords with APC connectors are not supported. All cables and cable assemblies used
must be compliant with the standards specified below:
•
•
•
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Singlemode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multi-Fiber Optical Connectors
Figure 2-48 shows the cable type for use with the XFP optical transceiver module on the Cisco
76-ES+XC-40G3C, 76-ES+XC-40G3CXL line card.
Figure 2-48
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 76-ES+T+XC-20G Line Card Overview
The following sections describe the Cisco 76-ES+T+XC-20G line cards:
•
•
•
•
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-66
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T+XC-20G Line Card Overview
•
Cisco 76-ES+T+XC-20G Line Card Processors
Table 2-64
Cisco 76-ES+T+XC-20G Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
control
processor
Cisco 76-ES+T+XC-20G Line Card LEDs
The Cisco 76-ES+T+XC-20G line cards have Status and A/L (Active Loopback) LEDs, as shown in
Figure 2-49
Cisco 76-ES+T+XC-20G Line Card Faceplate
76-ES+T-2TG
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Table 2-65 provides LED descriptions.
Table 2-65
Cisco 76-ES+T+XC-20G Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 76-ES+T+XC-20G Physical Specifications
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-67
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T+XC-20G Line Card Overview
Table 2-66
Cisco 76-ES+T+XC-20G Line Card Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 76-ES+T+XC-20G line card occupies one module slot and
can be operated in all Cisco 7600 series routers except the Cisco 7603
router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 76-ES+T+XC-20G Line Card Memory Options
Table 2-67 lists the memory options available for the Cisco 76-ES+T+XC-20G line cards:
Table 2-67 Cisco 76-ES+T+XC-20G Line Card Memory Options
Line Card
Memory Options
2 GB
Cisco 76-ES+T+XC-20G
Cisco 76-ES+T+XC-20G Supported XFP Modules
Table 2-68 Cisco 76-ES+T+XC-20G Supported XFP Modules
XFP
Description
XFP-10GLR-OC192SR
Cisco Multirate 10GBASE-LR and OC-192/STM-64 SR-1 XFP
Module for SMF
XFP-10GZR-OC192LR
XFP-10GER-192IR+
Cisco Multirate 10GBASE-ZR and OC-192/STM-64 lR-2 XFP
Module for SMF
Cisco Multirate 10GBASE-ER and OC-192/STM-64 IR-2 XFP
Module for SMF
XFP-10GLR-OC192SR-L
XFP-10GLR-OC192IR-L
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
DWDM-XFP-60.61
DWDM-XFP-59.79
DWDM-XFP-58.98
DWDM-XFP-58.17
DWDM-XFP-56.55
DWDM-XFP-55.75
DWDM XFP 1560.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1559.79 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.17 nm XFP (100 GHz ITU grid)
DWDM XFP 1556.55 nm XFP (100 GHz ITU grid)
DWDM XFP 1555.75 nm XFP (100 GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-68
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T+XC-20G Line Card Overview
Table 2-68 Cisco 76-ES+T+XC-20G Supported XFP Modules (continued)
XFP
Description
DWDM-XFP-54.94
DWDM-XFP-54.13
DWDM-XFP-52.52
DWDM-XFP-51.72
DWDM-XFP-50.92
DWDM-XFP-50.12
DWDM-XFP-48.51
DWDM-XFP-47.72
DWDM-XFP-46.92
DWDM-XFP-46.12
DWDM-XFP-44.53
DWDM-XFP-43.73
DWDM-XFP-42.94
DWDM-XFP-42.14
DWDM-XFP-40.56
DWDM-XFP-39.77
DWDM-XFP-38.98
DWDM-XFP-38.19
DWDM-XFP-36.61
DWDM-XFP-35.82
DWDM-XFP-35.04
DWDM-XFP-34.25
DWDM-XFP-32.68
DWDM-XFP-31.90
DWDM-XFP-31.12
DWDM-XFP-30.33
DWDM XFP 1554.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.13 nm XFP (100 GHz ITU grid)
DWDM XFP 1552.52 nm XFP (100 GHz ITU grid)
DWDM XFP 1551.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1548.51 nm XFP (100 GHz ITU grid)
DWDM XFP 1547.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1544.53 nm XFP (100 GHz ITU grid)
DWDM XFP 1543.73 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.14 nm XFP (100 GHz ITU grid)
DWDM XFP 1540.56 nm XFP (100 GHz ITU grid)
DWDM XFP 1539.77 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.19 nm XFP (100 GHz ITU grid)
DWDM XFP 1536.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.82 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.04 nm XFP (100 GHz ITU grid)
DWDM XFP 1534.25 nm XFP (100 GHz ITU grid)
DWDM XFP 1532.68 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.90 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1530.33 nm XFP (100 GHz ITU grid)
The XFP modules provide high-speed serial links at the following rates: 9.95 Gbps (OC-192) and
10.3125 Gbps (10 Gigabit Ethernet) ona single-mode fiber (SMF). The transmit side recovers and
retimes the 10-Gbps serial data, and passes it to a laser driver. The laser driver biases and modulates a
1310-nm or 1550-nm laser, enabling data transmission over SMF through an LC connector. The receive
side recovers and retimes the 10-Gbps optical data stream from a photo-detector transimpedance
amplifier, and passes it to an output driver.
See the label on the XFP module for technology type and model.
XFP module dimensions are:
•
•
•
Height: 12.5 mm
Width: 18.35 mm
Length: 71.1mm
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-69
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T+XC-40G Line Card Overview
Figure 2-50 XFP Module
Connectors and Cabling
The XFP optical transceiver module on the Cisco 76-ES+T+XC-20G line card requires dual LC or PC
connectors. Only the patch cord connections with PC or UPC connectors are supported. Patch cords with
APC connectors are not supported. All cables and cable assemblies used must be compliant with the
standards specified below:
•
•
•
GR-20-CORE: Generic requirements for optical fiber and optical fiber cable.
GR-326-CORE: Generic requirements for singlemode optical connectors and jumper assemblies.
GR-1435-CORE: Generic requirements for multi-fiber optical connectors.
Figure 2-51 shows the cable type used with the XFP optical transceiver module on the Cisco
76-ES+T+XC-20G card.
Figure 2-51
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 76-ES+T+XC-40G Line Card Overview
The following sections describe the Cisco 76-ES+T+XC-40G line cards:
•
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-70
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T+XC-40G Line Card Overview
•
•
•
•
Cisco 76-ES+T+XC-40G Line Card Processors
Table 2-69
Cisco 76-ES+T+XC-40G Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
control
processor
Cisco 76-ES+T+XC-40G Line Card LEDs
The Cisco 76-ES+T+XC-40G line cards have Status and A/L (Active Loopback) LEDs, as shown in
Figure 2-52
Cisco 76-ES+T+XC-40G Line Card Faceplate
76-ES+T-2TG
EXT CLK
STATUS
ETHERNET SERVICES MODULE
CLASS
1
LASER
Table 2-70 provides LED descriptions.
Table 2-70
Cisco 76-ES+T+XC-40G Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-71
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T+XC-40G Line Card Overview
Cisco 76-ES+T+XC-40G Physical Specifications
Table 2-71
Cisco 76-ES+T+XC-40G Line Card Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 76-ES+T+XC-40G line card occupies one module slot and
can be operated in all Cisco 7600 series routers except the Cisco 7603
router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 76-ES+T+XC-40G Line Card Memory Options
Table 2-72 lists the memory options available for the Cisco 76-ES+T+XC-40G line cards:
Table 2-72 Cisco 76-ES+T+XC-40G Line Card Memory Options
Line Card
Memory Options
2 GB
Cisco 76-ES+T+XC-40G
Cisco 76-ES+T+XC-40G Supported XFP Modules
Table 2-73 Cisco 76-ES+T+XC-40G Supported XFP Modules
XFP
Description
XFP-10GLR-OC192SR
Cisco Multirate 10GBASE-LR and OC-192/STM-64 SR-1 XFP
Module for SMF
XFP-10GZR-OC192LR
XFP-10GER-192IR+
Cisco Multirate 10GBASE-ZR and OC-192/STM-64 lR-2 XFP
Module for SMF
Cisco Multirate 10GBASE-ER and OC-192/STM-64 IR-2 XFP
Module for SMF
XFP-10GLR-OC192SR-L
XFP-10GLR-OC192IR-L
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
Cisco Multirate 10GBASE-LR Ethernet and OC-192/STM-64 low
power XFP Module for SMF
DWDM-XFP-60.61
DWDM-XFP-59.79
DWDM-XFP-58.98
DWDM XFP 1560.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1559.79 nm XFP (100 GHz ITU grid)
DWDM XFP 1558.98 nm XFP (100 GHz ITU grid)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-72
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T+XC-40G Line Card Overview
Table 2-73 Cisco 76-ES+T+XC-40G Supported XFP Modules (continued)
XFP
Description
DWDM-XFP-58.17
DWDM-XFP-56.55
DWDM-XFP-55.75
DWDM-XFP-54.94
DWDM-XFP-54.13
DWDM-XFP-52.52
DWDM-XFP-51.72
DWDM-XFP-50.92
DWDM-XFP-50.12
DWDM-XFP-48.51
DWDM-XFP-47.72
DWDM-XFP-46.92
DWDM-XFP-46.12
DWDM-XFP-44.53
DWDM-XFP-43.73
DWDM-XFP-42.94
DWDM-XFP-42.14
DWDM-XFP-40.56
DWDM-XFP-39.77
DWDM-XFP-38.98
DWDM-XFP-38.19
DWDM-XFP-36.61
DWDM-XFP-35.82
DWDM-XFP-35.04
DWDM-XFP-34.25
DWDM-XFP-32.68
DWDM-XFP-31.90
DWDM-XFP-31.12
DWDM-XFP-30.33
DWDM XFP 1558.17 nm XFP (100 GHz ITU grid)
DWDM XFP 1556.55 nm XFP (100 GHz ITU grid)
DWDM XFP 1555.75 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1554.13 nm XFP (100 GHz ITU grid)
DWDM XFP 1552.52 nm XFP (100 GHz ITU grid)
DWDM XFP 1551.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1550.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1548.51 nm XFP (100 GHz ITU grid)
DWDM XFP 1547.72 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.92 nm XFP (100 GHz ITU grid)
DWDM XFP 1546.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1544.53 nm XFP (100 GHz ITU grid)
DWDM XFP 1543.73 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.94 nm XFP (100 GHz ITU grid)
DWDM XFP 1542.14 nm XFP (100 GHz ITU grid)
DWDM XFP 1540.56 nm XFP (100 GHz ITU grid)
DWDM XFP 1539.77 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.98 nm XFP (100 GHz ITU grid)
DWDM XFP 1538.19 nm XFP (100 GHz ITU grid)
DWDM XFP 1536.61 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.82 nm XFP (100 GHz ITU grid)
DWDM XFP 1535.04 nm XFP (100 GHz ITU grid)
DWDM XFP 1534.25 nm XFP (100 GHz ITU grid)
DWDM XFP 1532.68 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.90 nm XFP (100 GHz ITU grid)
DWDM XFP 1531.12 nm XFP (100 GHz ITU grid)
DWDM XFP 1530.33 nm XFP (100 GHz ITU grid)
The XFP modules provide high-speed serial links at the following rates: 9.95 Gbps (OC-192) and
10.3125 Gbps (10 Gigabit Ethernet) ona single-mode fiber (SMF). The transmit side recovers and
retimes the 10-Gbps serial data, and passes it to a laser driver. The laser driver biases and modulates a
1310-nm or 1550-nm laser, enabling data transmission over SMF through an LC connector. The receive
side recovers and retimes the 10-Gbps optical data stream from a photo-detector transimpedance
amplifier, and passes it to an output driver.
See the label on the XFP module for technology type and model.
XFP module dimensions are:
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-73
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T+XC-40G Line Card Overview
•
•
•
Height: 12.5 mm
Width: 18.35 mm
Length: 71.1mm
Figure 2-53 XFP Module
Connectors and Cabling
The XFP optical transceiver module on the Cisco 76-ES+T+XC-40G line card requires dual LC or PC
connectors. Only the patch cord connections with PC or UPC connectors are supported. Patch cords with
APC connectors are not supported. All cables and cable assemblies used must be compliant with the
standards specified below:
•
•
•
GR-20-CORE: Generic requirements for optical fiber and optical fiber cable.
GR-326-CORE: Generic requirements for singlemode optical connectors and jumper assemblies.
GR-1435-CORE: Generic requirements for multi-fiber optical connectors.
Figure 2-54 shows the cable type used with the XFP optical transceiver module on the Cisco
76-ES+T+XC-40G card.
Figure 2-54
Duplex LC-Type Cable and Connector
For additional information on Cisco Transceiver Modules, see
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-74
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-8TG Line Card Overview
Cisco 76-ES+T-8TG Line Card Overview
The following sections describe the Cisco 76-ES+T-8TG line cards:
•
•
•
•
•
•
Cisco 76-ES+T-8TG Line Card Processors
Table 2-74
Cisco 76-ES+T-8TG Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
Control
Processor
Cisco 76-ES+T-8TG Line Card LEDs
The Cisco 76-ES+T-8TG line cards have Status and A/L (Active Loopback) LEDs, as shown in
Figure 2-55
Cisco 76-ES+T-8TG Line Card Faceplate
333598
Table 2-75 provides LED description.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-75
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+T-8TG Line Card Overview
Table 2-75
Cisco 76-ES+T-8TG Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled, but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 76-ES+T-8TG Physical Specifications
Table 2-76 lists the physical specifications of Cisco 76-ES+T-8TG line card.
Table 2-76
Cisco 76-ES+T-8TG Line Card Physical Specifications
Description
Specifications
Physical dimensions
The Cisco 76-ES+T-8TG line card occupies a single module slot and
can be operated in all the Cisco 7600 series routers except for the
Cisco 7603 router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 76-ES+T-8TG Line Card Memory Options
Table 2-77 lists the memory options available for the Cisco 76-ES+T-8TG line cards:
Table 2-77
Cisco 76-ES+T-8TG Line Card Memory Options
Line Card
Memory Options
2 GB
Cisco 76-ES+T-8TG
Cisco 76-ES+T-8TG Supported Features
The Cisco 76-ES+T-8TG line card supports all the features supported on a regular ES+ card, but at a
lower scale suitable for a low queue deployment. The line card is limited to 16 queues per port. The
following additional features are supported:
•
Enhanced small form-factor pluggable (SFP+)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-76
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XT-8TG Line Card Overview
•
•
Port Mapping: The ES+ HD has eight 10GE ports. The first port of each NP is numbered from 1 to
4 (NP 0 to NP 3), and each NP’s second 10GE port is numbered from 5 to 8.
Oversubscription: Theoretically each NP supports 15Gb on the egress side. For instance, 10Gb
traffic is sent from the line card to NP, which has 5Gb of multicast and 5Gb of unicast traffic. Using
loopback interface, the NP replicates the multicast packets and sends 5Gb traffic on each NP port.
This traffic is divided into 2.5Gb on each port. So, effectively each NP port or interface receives
7.5Gb traffic. Since there are two 10Gb ports on each NP, the total rate achieved is 15Gb.
On the ingress path, more than 10Gb is supported for higher packet size. For instance, when the NP
receives the packets at the rate of 10Gb, and each packet size is 64 bytes, it will be 96 bytes (64 +32
byte DBUS header) when it moves from NP to line card. So, it consumes entire bandwidth and
restrict the ingress traffic to 10Gb. If the packet size is greater than 64 bytes, it will give more than
10Gb throughput.
Cisco 76-ES+T-8TG Supported SFP+ Modules
The Cisco 76-ES+T-8TG line cards support the enhanced small form-factor pluggable (SFP+) optical
Table 2-78
Cisco 76-ES+T-8TG Supported SFP+ Modules
SFP+ Modules
SFP-10G-SR-X
SFP-10G-LR-X
Description
10GE SFP+, Short range.
10GE SFP+, Long range.
Cisco 76-ES+XT-8TG Line Card Overview
The following sections describe the Cisco 76-ES+XT-8TG line cards:
•
•
•
•
•
Cisco 76-ES+XT-8TG Line Card Processors
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-77
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XT-8TG Line Card Overview
Table 2-79
Cisco 76-ES+XT-8TG Line Card Processor
Type
Speed
Description
CPU
300 megahertz (MHz) internal operating
frequency
Trident Processor
Local
1333 MHz (1.3GHz)
MPC8548
Control
Processor
Cisco 76-ES+XT-8TG Line Card LEDs
The Cisco 76-ES+XT-8TG line cards have Status and A/L (Active Loopback) LEDs, as shown in
Figure 2-56
Cisco 76-ES+XT-8TG Line Card Faceplate
333598
Table 2-80 provides LED description.
Table 2-80
Cisco 76-ES+XT-8TG Line Card LEDs
LED Label
Color
Red
State
On
Meaning
STATUS
The line card has encountered an error.
The line card is online.
The line card is loading.
The line card is powered off.
Green
Yellow
Off
On
On
Off
On
A/L
Amber
The port is enabled, but there is not a valid Ethernet
link.
Green
Off
On
The port is enabled and a valid Ethernet link has been
established.
Off
The port is not enabled by software.
Cisco 76-ES+XT-8TG Physical Specifications
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-78
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XT-8TG Line Card Overview
Table 2-81
Cisco 76-ES+XT-8TG Line Card Physical Specifications
Specifications
Description
Physical dimensions
The Cisco 76-ES+XT-8TG line card occupies a single module slot and
can be operated in all the Cisco 7600 series routers except for the
Cisco 7603 router.
Shipping weight
8 lb (3.64 kg)
Operating temperature
Relative humidity
Storage temperature
32 to 104°F (0 to 40°C)
10 to 90 percent, noncondensing
–4 to 149°F (–20 to 65°C)
Cisco 76-ES+XT-8TG Line Card Memory Options
Table 2-82 Cisco 76-ES+XT-8TG Line Card Memory Options
Line Card
Memory Options
2 GB
Cisco 76-ES+XT-8TG
Cisco 76-ES+XT-8TG Supported SFP+ Modules
The Cisco 76-ES+XT-8TG line cards support the enhanced small form-factor pluggable (SFP+) optical
Table 2-83
Cisco 76-ES+XT-8TG Supported SFP+ Modules
SFP+ Modules
SFP-10G-SR-X
SFP-10G-LR-X
Description
10GE SFP+, Short range.
10GE SFP+, Long range.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-79
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Overview: Cisco 7600 Series Ethernet Services Plus Line Cards
Cisco 76-ES+XT-8TG Line Card Overview
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
2-80
Download from Www.Somanuals.com. All Manuals Search And Download.
C H A P T E R
3
Preparing to Install a Cisco 7600 Series Ethernet
Services Plus Line Card
This chapter describes the general equipment, safety, and site preparation requirements for installing a
Cisco 7600 Series Ethernet Services + line card. This chapter contains the following sections:
•
•
•
Required Tools and Equipment
You need the following tools and parts to remove and install Cisco 7600 ES+ line cards. If you need
additional equipment, contact a service representative.
•
•
•
•
•
•
Cisco 7600 Series ES+ line card
Interface cables to connect the Cisco 7600 ES+ line card with another router or switch
Any SFP or XFP modules, or memory you need to install (and are not already installed)
Number 1 Phillips and a 3/16-inch flat-blade screwdriver
Number 2 Phillips screwdriver
Your own electrostatic discharge (ESD)-prevention equipment or the ESD-preventive wrist or ankle
strap and instructions supplied with your line card
•
•
•
Antistatic mat
Antistatic container
Fiber-optic end-face cleaning tools and inspection equipment. For complete information on
inspecting and cleaning fiber-optic connections, refer to the white-paper document at this URL:
http://www.cisco.com/en/US/tech/tk482/tk607/technologies_white_paper09186a0080254eba.shtml
Safety Guidelines
This section provides safety guidelines that you should follow when working with any equipment that
connects to electrical power or telephone wiring.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing to Install a Cisco 7600 Series Ethernet Services Plus Line Card
Safety Guidelines
Safety Warnings
Safety warnings appear throughout this publication in procedures that, if performed incorrectly, might
harm you. A warning symbol precedes each warning statement.
Warning Definition
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device. Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing to Install a Cisco 7600 Series Ethernet Services Plus Line Card
Safety Guidelines
Warnung
Avvertenza
Advarsel
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing to Install a Cisco 7600 Series Ethernet Services Plus Line Card
Safety Guidelines
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing to Install a Cisco 7600 Series Ethernet Services Plus Line Card
Safety Guidelines
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing to Install a Cisco 7600 Series Ethernet Services Plus Line Card
Safety Guidelines
Electrical Equipment Guidelines
Follow these basic guidelines when working with any electrical equipment:
•
Before beginning any procedures requiring access to the chassis interior, locate the emergency
power-off switch for the room in which you are working.
•
•
•
•
Disconnect all power and external cables before moving a chassis.
Do not work alone when potentially hazardous conditions exist.
Never assume that power has been disconnected from a circuit; always check.
Do not perform any action that creates a potential hazard to people or makes the equipment unsafe;
carefully examine your work area for possible hazards such as moist floors, ungrounded power
extension cables, and missing safety grounds.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing to Install a Cisco 7600 Series Ethernet Services Plus Line Card
Safety Guidelines
Telephone Wiring Guidelines
Use the following guidelines when working with any equipment that is connected to telephone wiring or
to other network cabling:
•
•
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
•
•
Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
Use caution when installing or modifying telephone lines.
Preventing Electrostatic Discharge Damage
Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are
improperly handled, results in complete or intermittent failures. An Cisco 7600 Series ES+ line card
comprises printed circuit boards that are fixed ina metal carrier. Electromagnetic interference (EMI)
shielding and connectors are integral components of the carrier. Although the metal carrier helps to
protect the board from ESD, use a preventive antistatic strap during handling.
Following are guidelines for preventing ESD damage:
•
•
•
Always use an ESD wrist or ankle strap and ensure that it makes good skin contact.
Connect the equipment end of the strap to an unfinished chassis surface.
When installing a component, use any available ejector levers or captive installation screws to
properly seat the bus connectors in the backplane or midplane. These devices prevent accidental
removal, provide proper grounding for the system, and help to ensure that bus connectors are
properly seated.
•
•
•
When removing a component, use any available ejector levers or captive installation screws to
release the bus connectors from the backplane or midplane.
Handle carriers by available handles or edges only; avoid touching the printed circuit boards or
connectors.
Place a removed board component-side-up on an antistatic surface or in a static shielding container.
If you plan to return the component to the factory, immediately place it in a static shielding
container.
•
•
Avoid contact between the printed circuit boards and clothing. The wrist strap only protects
components from ESD voltages on the body; ESD voltages on clothing can still cause damage.
Never attempt to remove the printed circuit board from the metal carrier.
Caution
For safety, periodically check the resistance value of the antistatic strap. The measurement should be
between 1 and 10 megohms (Mohms).
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing to Install a Cisco 7600 Series Ethernet Services Plus Line Card
Laser/LED Safety
Laser/LED Safety
An optical single-mode transmitter uses a small laser to transmit the light signal to the network ring.
Keep the transmit port covered whenever a cable is not connected to it. Although multimode transceivers
typically use LEDs for transmission, it is good practice to keep open ports covered and avoid staring into
open ports or apertures. The single-mode aperture port contains a laser warning label, as shown in
These warnings apply to SFP and XFP modules that transmit signals via an optical carrier signal.
Figure 3-1
Class 1 Laser Warning Labels for Single-Mode Port
CLASS 1 LASER PRODUCT
LASERPRODUKT DER KLASSE 1
PRODUIT LASER DE CLASSE 1
1
PRODUCTO LASER CLASE 1
Warning
Class 1 laser product. Statement 1008
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into
beams or view directly with optical instruments. Statement 1051
Waarschuwing
Losgekoppelde of losgeraakte glasvezels of aansluitingen kunnen onzichtbare laserstraling
produceren. Kijk niet rechtstreeks in de straling en gebruik geen optische instrumenten rond deze
glasvezels of aansluitingen.
Varoitus
Irrotetuista kuiduista tai liittimistä voi tulla näkymätöntä lasersäteilyä. Älä tuijota säteitä tai katso
niitä suoraan optisilla välineillä.
Attention
Les fibres ou connecteurs débranchés risquent d'émettre des rayonnements laser invisibles à l'œil.
Ne regardez jamais directement les faisceaux laser à l'œil nu, ni d'ailleurs avec des instruments
optiques.
Warnung
Avvertenza
Advarsel
Aviso
Unterbrochene Fasern oder Steckerverbindungenkönnen unsichtbare Laserstrahlung abgeben.
Blicken Sie weder mit bloßem Auge noch mit optischen Instrumenten direkt in Laserstrahlen.
Le fibre ottiche ed i relativi connettori possono emettere radiazioni laser. I fasci di luce non devono
mai essere osservati direttamente o attraverso strumenti ottici.
Det kan forekomme usynlig laserstråling fra fiber eller kontakter som er frakoblet. Stirr ikke direkte
inn i strålene eller se på dem direkte gjennom et optisk instrument.
Radiação laser invisível pode ser emitida de conectores ou fibras desconectadas. Não olhe
diretamente para os feixes ou com instrumentos ópticos.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing to Install a Cisco 7600 Series Ethernet Services Plus Line Card
Laser/LED Safety
¡Advertencia!
Varning!
Es posible que las fibras desconectadas emitan radiación láser invisible. No fije la vista en los
rayos ni examine éstos con instrumentos ópticos.
Osynlig laserstrålning kan avges från frånkopplade fibrer eller kontaktdon. Rikta inte blicken in i
strålar och titta aldrig direkt på dem med hjälp av optiska instrument.
Aviso
Radiação laser invisível pode ser emitida a partir de fibras ou conectores desconectados. Não fixe
o olhar nos feixes e nem olhe diretamente com instrumentos ópticos.
Advarsel
Usynlig laserstråling kan forekomme fra brugte fibre eller stik. Stir ikke ind i stråler eller direkte
med optiske instrumenter.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Preparing to Install a Cisco 7600 Series Ethernet Services Plus Line Card
Laser/LED Safety
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into
beams or view directly with optical instruments. Statement 1051
Warning
Class 1 LED product. Statement 1027
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
C H A P T E R
4
Installing and Removing a Cisco 7600 Series
Ethernet Services Plus Line Card
This chapter describes how to install or remove Cisco 7600 Series Ethernet Services + line cards on the
Cisco 7600 series routers. This chapter contains the following sections:
•
•
Handling Cisco 7600 Series Ethernet Services Plus Line Cards
Each Cisco 7600 Series ES+ line card circuit board is mounted to a metal carrier and is sensitive to
electrostatic discharge (ESD) damage. Before you begin installation, read Chapter 3, “Preparing to
Install a Cisco 7600 Series Ethernet Services Plus Line Card,” for a list of parts and tools required for
installation.
Caution
Always handle the Cisco 7600 Series ES+ line card by the carrier edges and handle; never touch the line
When a slot is not in use, a blank filler plate must be installed in the empty slot to allow the router or
switch to conform to electromagnetic interference (EMI) emissions requirements and to allow proper
airflow across the installed modules. If you plan to install a Cisco 7600 Series ES+ line card in a slot
that is not in use, you must first remove the blank filler plate.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Installing and Removing a Cisco 7600 Series Ethernet Services Plus Line Card
Online Insertion and Removal
Figure 4-1
Handling a Cisco 7600 Series ES+ line card
Printed circuit board
Metal carrier
GND
Online Insertion and Removal
The Cisco 7600 series routers support online insertion and removal (OIR) of the Cisco 7600 Series ES+
line card, as well as OIR for the SFP or XFP modules. Therefore, you can remove a Cisco 7600 Series
ES+ line card with its SFP or XFP modules still intact, or you can remove SFP or XFP modules
independently from the Cisco 7600 Series ES+ line card, leaving the line card installed in the router.
Note
The 40 port versions (7600-ES+40G3C and 7600-ES+40G3CXL) require longer maintenance time for
card replacement.
This section includes the following topics on OIR support:
•
•
•
Preparing for Online Removal of a Cisco 7600 Series Ethernet Services Plus Line
Card
The Cisco 7600 series routers support OIR of the Cisco 7600 Series ES+ line card. To do this, you can
power down a Cisco 7600 Series ES+ line card (which automatically deactivates any installed SFP or
XFP modules) and remove the Cisco 7600 Series ES+ line card with the SFP or XFP modules still intact.
Although graceful deactivation of a 7600 ES+ line card is preferred using the no power enable module
command, the Cisco 7600 series routers do support removal of the 7600 ES+ line card without
deactivating it first.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Installing and Removing a Cisco 7600 Series Ethernet Services Plus Line Card
Online Insertion and Removal
If you plan to remove a Cisco 7600 Series ES+ line card, you can deactivate the Cisco 7600 Series ES+
line card first, using the no power enable module global configuration command.
When you deactivate a Cisco 7600 Series ES+ line card using this command, it automatically deactivates
each of the SFP or XFP modules that are installed in that Cisco 7600 Series ES+ line card. Therefore, it
is not necessary to deactivate each of the SFP or XFP modules prior to deactivating the Cisco 7600 Series
ES+ line card.
Caution
When you replace a Cisco 7600 Series ES+ line card with a different type of Cisco 7600 Series ES+ line
card, the configurations are not saved automatically.
Replacing a Cisco 7600 Series Ethernet Services Plus Line Card
1. Capture the health of the steady state system running the target IOS and traffic snapshot.
2. Use the show run module command to display the running configuration of the module.
3. Save the running configuration to a file using the copy running-config tftp command. You are
prompted to provide the address of the TFTP server and the file name.
4. Power down the old card using the no power enable module command.
5. Remove the old card from the slot and disconnect all cables. See Deactivating a Cisco 7600 Series
6. Replace with a new card in the same slot and reconnect all the cables disconnected in the previous
step, with a 1:1 port correspondence.
8. Copy and paste the running configuration saved in Step 3 on the new card.
9. Enable all the interfaces using the no shut command in interface configuration mode.
10. Capture another health snapshot and compare these results with the results noted in Step 1.
11. Perform Stateful Switchover (SSO) to ensure proper working of HA.
12. Perform generic health check.
13. Perform SSO to restore active or standby roles as before.
Deactivating a Cisco 7600 Series Ethernet Services Plus Line Card
To deactivate a 7600 ES+ Ethernet line card and its installed SFPs or XFPs prior to removal of the 7600
ES+ line card, use the following command in global configuration mode:
Command
Purpose
Router(config)# no power enable module
slot
Shuts down any installed interfaces, and deactivates the
7600 ES+ line card in the specified slot, where:
•
slot—Specifies the chassis slot number where the
7600 ES+ line card is installed.
For more information about chassis slot numbering, refer to the “Identifying Slots and Subslots for the
Cisco 7600 Cisco 7600 Series ES+ Line Cards” section on page 2-3 section in this guide.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Installing and Removing a Cisco 7600 Series Ethernet Services Plus Line Card
Online Insertion and Removal
Reactivating a Cisco 7600 Series Ethernet Services Plus Line Card
Once you deactivate a Cisco 7600 Series ES+ line card, whether or not you have performed an OIR, you
must use the power enable module global configuration command to reactivate the Cisco 7600 Series
ES+ line card.
If you did not issue a command to deactivate the SFP or XFP modules installed in a Cisco 7600 Series
ES+ line card, but you did deactivate the Cisco 7600 Series ES+ line card using the no power enable
module command, then you do not need to reactivate the SFP or XFP modules after an OIR of the Cisco
7600 Series ES+ line card. The installed SFP or XFP modules automatically reactivate upon reactivation
of the Cisco 7600 Series ES+ line card in the router.
For example, consider the case where you remove a Cisco 7600 Series ES+ line card from the router to
replace it with another Cisco 7600 Series ES+ line card. You reinstall the same SFP or XFP modules into
the new Cisco 7600 Series ES+ line card. When you enter the power enable module command on the
router, the SFP or XFP modules will automatically reactivate with the new Cisco 7600 Series ES+ line
card.
To activate a Cisco 7600 Series ES+ line card and its installed SFP or XFP modules after the Cisco 7600
Series ES+ line card has been deactivated, use the following command in global configuration mode:
Command
Purpose
Router(config)# power enable module slot Activates the ES+ line card in the specified slot and its
installed SFPs or XFPs, where:
•
slot—Specifies the chassis slot number where the
ES+ line card is installed.
For more information about chassis slot numbering, refer to the Identifying Slots and Subslots for the
Cisco 7600 Cisco 7600 Series ES+ Line Cards, page 2-3 section in this guide.
Verifying Deactivation and Activation of a Cisco 7600 Series Ethernet Services
Plus Line Card
To verify the deactivation of a 7600 ES+ line card, enter the show module command in privileged EXEC
configuration mode. Observe the Status field associated with the 7600 ES+ line card that you want to
verify.
The following example shows 7600 ES+ line cards located in slots 4 and 6. Slot 6 is powered down. This
is indicated by its “PwrDown” status.
Router# show module
Mod Ports Card Type
Model
Serial No.
--- ----- -------------------------------------- ------------------ -----------
1
2
3
4
5
6
24 CEF720 24 port 1000mb SFP
48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX
0 4-subslot SPA Interface Processor-200 7600-SIP-200
40 7600 ES+
2 Supervisor Engine 720 (Active)
4 7600 ES+
WS-X6724-SFP
SAL0930696R
SAL0929634V
JAB09270AEQ
JAE1146355M
SAD085106Z7
JAE11518648
7600-ES+40G3CXL
WS-SUP720-3BXL
7600-ES+4TG3C
Mod MAC addresses
Hw
Fw
Sw
Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0014.f212.0028 to 0014.f212.003f
2 0014.f211.f20c to 0014.f211.f23b
2.2
2.2
12.2(14r)S5 12.2(nightly Ok
12.2(14r)S5 12.2(nightly Ok
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Installing and Removing a Cisco 7600 Series Ethernet Services Plus Line Card
Online Insertion and Removal
3 0014.a8f7.1c40 to 0014.a8f7.1c7f
4 001d.e5e8.1740 to 001d.e5e8.179f
5 0011.21ba.9a48 to 0011.21ba.9a4b
6 001d.e5e8.2e00 to 001d.e5e8.2e0f
1.1
0.301 12.2(33r)SRD 12.2(nightly Ok
4.1 8.4(2) 12.2(nightly Ok
0.301 12.2(33r)SRD 12.2(nightly PwrDown
12.2(nightly 12.2(nightly Ok
Mod Sub-Module
Model
Serial
Hw
Status
---- --------------------------- ------------------ ----------- ------- -------
1 Centralized Forwarding Card WS-F6700-CFC
2 Centralized Forwarding Card WS-F6700-CFC
SAL1021PB1F 2.0
SAL085285LJ 2.0
JAB09270B3J 1.0
JAE11463519 0.200 Ok
JAE114632R4 0.300 Ok
SAD0851042D 1.4
SAD085002WF 2.2
0.301 PwrDown
JAE1151864W 0.201 PwrDown
Ok
Ok
Ok
3/2 4xT3E3 SPA
4 7600 ES+ DFC XL
SPA-4XT3/E3
7600-ES+3CXL
7600-ES+40G
WS-F6K-PFC3BXL
WS-SUP720
4 7600 ES+ 40xGE SFP
5 Policy Feature Card 3
5 MSFC3 Daughterboard
6 7600 ES+ DFC LITE
6 7600 ES+ 4x10GE XFP
Ok
Ok
7600-ES+3C
7600-ES+4TG
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
3 Pass
3/2 Pass
4 Pass
5 Pass
6 Not Applicable
Router#
To verify activation and proper operation of a 7600 ES+ line card, enter the show module command and
observe “Ok” in the Status field as shown in the following example:
Router# show module
Mod Ports Card Type
Model
Serial No.
--- ----- -------------------------------------- ------------------ -----------
1
2
3
4
5
6
24 CEF720 24 port 1000mb SFP
48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX
0 4-subslot SPA Interface Processor-200 7600-SIP-200
40 7600 ES+
2 Supervisor Engine 720 (Active)
4 7600 ES+
WS-X6724-SFP
SAL0930696R
SAL0929634V
JAB09270AEQ
JAE1146355M
SAD085106Z7
JAE11518648
7600-ES+40G3CXL
WS-SUP720-3BXL
7600-ES+4TG3C
Mod MAC addresses
Hw
Fw
Sw
Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0014.f212.0028 to 0014.f212.003f
2 0014.f211.f20c to 0014.f211.f23b
3 0014.a8f7.1c40 to 0014.a8f7.1c7f
4 001d.e5e8.1740 to 001d.e5e8.179f
5 0011.21ba.9a48 to 0011.21ba.9a4b
6 001d.e5e8.2e00 to 001d.e5e8.2e0f
2.2
2.2
1.1
12.2(14r)S5 12.2(nightly Ok
12.2(14r)S5 12.2(nightly Ok
12.2(nightly 12.2(nightly Ok
0.301 12.2(33r)SRD 12.2(nightly Ok
4.1 8.4(2) 12.2(nightly Ok
0.301 12.2(33r)SRD 12.2(nightly Ok
Mod Sub-Module
Model
Serial
Hw
Status
---- --------------------------- ------------------ ----------- ------- -------
1 Centralized Forwarding Card WS-F6700-CFC
2 Centralized Forwarding Card WS-F6700-CFC
SAL1021PB1F 2.0
SAL085285LJ 2.0
JAB09270B3J 1.0
JAE11463519 0.200 Ok
JAE114632R4 0.300 Ok
SAD0851042D 1.4
SAD085002WF 2.2
0.301 Ok
JAE1151864W 0.201 Ok
Ok
Ok
Ok
3/2 4xT3E3 SPA
4 7600 ES+ DFC XL
SPA-4XT3/E3
7600-ES+3CXL
7600-ES+40G
WS-F6K-PFC3BXL
WS-SUP720
4 7600 ES+ 40xGE SFP
5 Policy Feature Card 3
5 MSFC3 Daughterboard
6 7600 ES+ DFC LITE
6 7600 ES+ 4x10GE XFP
Ok
Ok
7600-ES+3C
7600-ES+4TG
Mod Online Diag Status
---- -------------------
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Installing and Removing a Cisco 7600 Series Ethernet Services Plus Line Card
Online Insertion and Removal
1 Pass
2 Pass
3 Pass
3/2 Pass
4 Pass
5 Pass
6 Pass
Router#
Router2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
PE2(config)#no power enable module 6
PE2(config)#end
PE2#
*May 15 10:30:54.227 UTC: %SYS-5-CONFIG_I: Configured from console by console
PE2#
*May 15 10:30:53.325 UTC: %C6KPWR-SP-4-DISABLED: power to module in slot 6 set off (admin
request)
Router#
Preparing for Online Removal of a SFP or XFP Modules
The Cisco 7600 series routers support OIR of a SFP or XFP modules independently of removing the
Cisco 7600 Series ES+ line card. This means that a Cisco 7600 Series ES+ line card can remain installed
in the router with one XFP remaining active, while you remove another XFP from one of the line card
ports. Or, that an Cisco 7600 Series ES+ line card can remain installed in the router with some number
of SFP modules remaining active, while you remove other SFP modules from the line card ports.
The interface configuration is retained (recalled) if a Cisco 7600 Series ES+ line card or SFP or XFP is
removed and then replaced with one of the same type.
If you are planning to remove a Cisco 7600 Series ES+ line card along with its SFP or XFP modules,
then you do not need to follow the instructions in this section. To remove a Cisco 7600 Series ES+ line
card, see the “Preparing for Online Removal of a Cisco 7600 Series Ethernet Services Plus Line Card”
SFP Module or XFP Module OIR
The SFP and XFP modules support online insertion and removal (OIR). However, if the line card is
already installed in the router and the system is operational, we recommend that you administratively
shut down the SFP or XFP module port before installing a new module.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
C H A P T E R
5
Installing and Removing SFP and XFP Modules
This chapter describes how to install or remove small form-factor pluggable (SFP modules or XFP
modules) on the Cisco 7600 Series Ethernet Services + line cards. This chapter contains the following
sections:
•
•
Removing and Installing SFP Modules
Note
The Cisco 7600 ES+ will only accept the SFP modules listed as supported in this document. An SFP
check is run every time an SFP module is inserted into a Cisco 7600 ES+ and only SFP modules that
pass this check are usable.
Before you remove or install an SFP module, read the installation information in this section and the
Caution
Caution
Protect the SFP modules by inserting clean dust covers into them after the cables are removed. Be sure
to clean the optic surfaces of the fiber cables before you plug them back into the optical ports of another
SFP module. Avoid getting dust and other contaminants into the optical ports of your SFP modules,
because the optics will not work correctly when obstructed with dust.
It is strongly recommended that you do not install or remove the SFP module with fiber-optic cables
attached to it because of the potential of damaging the cable, the cable connector, or the optical interfaces
in the SFP module. Disconnect all cables before removing or installing an SFP module.
Removing and inserting an SFP module can shorten its useful life, so you should not remove and insert
SFP modules any more often than is absolutely necessary.
SFP modules use one of four different latching devices to install and remove the module from a port.
The four types of SFP module latching devices are described in the following sections:
•
•
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing SFP Modules
•
•
Bale Clasp SFP Module
The bale clasp SFP module has a clasp that you use to remove or install the SFP module. (See
Figure 5-1
Bale Clasp SFP Module
Removing a Bale Clasp SFP Module
To remove this type of SFP module, follow these steps:
Step 1
Step 2
Attach an ESD-preventive wrist or ankle strap and follow its instructions for use.
Disconnect and remove all interface cables from the ports; note the current connections of the cables to
the ports on the line card.
Step 3
Step 4
Open the bale clasp on the SFP module with your index finger in a downward direction, as shown in
Figure 5-2. If the bale clasp is obstructed and you cannot use your index finger to open it, use a small
flat-blade screwdriver to open the bale clasp.
Grasp the SFP module between your thumb and index finger and carefully remove it from the port, as
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing SFP Modules
Figure 5-2
Removing a Bale Clasp SFP Module
760
0
-
ES
+
20G3CXL
1
3
5
7
9
ST
A
T
US
ET SER
E
2
4
6
8
10
7600
-E
S+
20G3CX
L
1
3
5
7
9
ST
A
T
US
ETH
4
6
8
10
Step 5
Step 6
Place the removed SFP module on an antistatic mat, or immediately place it in a static shielding bag if
you plan to return it to the factory.
Protect your line card by inserting clean SFP module cage covers into the optical module cage when
there is no SFP module installed.
Installing a Bale Clasp SFP Module
To install this type of SFP module, follow these steps:
Step 1
Attach an ESD-preventive wrist or ankle strap and follow its instructions for use.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing SFP Modules
Step 2
Step 3
Close the bale clasp before inserting the SFP module.
Figure 5-3
Installing a Bale Clasp SFP Module into a Port
760
0
-
ES
+
20G3CXL
1
3
5
7
9
EXT CLK
ST
A
T
US
2
4
6
8
10
Note
Verify that the SFP modules are completely seated and secured in their assigned receptacles on the line
card by firmly pushing on each SFP module. If the SFP module is not completely seated and secured in
the receptacle, you will hear a click as the triangular pin on the bottom of the SFP module snaps into the
hole in the receptacle.
Mylar Tab SFP Module
The mylar tab SFP module has a tab that you pull to remove the module from a port. (See Figure 5-4.)
Figure 5-4 Mylar Tab SFP Module
Removing a Mylar Tab SFP Module
To remove this type of SFP module, follow these steps:
Step 1
Attach an ESD-preventive wrist or ankle strap and follow its instructions for use.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing SFP Modules
Step 2
Step 3
Disconnect and remove all interface cables from the ports; note the current connections of the cables to
the ports on the line card.
Pull the tab gently in a slightly downward direction until it disengages from the port, then pull the SFP
Figure 5-5
Removing a Mylar Tab SFP Module
7600
-
E
S
+
20G3CXL
1
3
5
7
9
EXT CLK
ST
A
T
US
TUS
A
T
MODULE
2
4
6
8
0
1
Step 4
Step 5
Place the removed SFP module on an antistatic mat, or immediately place it in a static shielding bag if
you plan to return it to the factory.
Protect your line card by inserting clean SFP module cage covers into the optical module cage when
there is no SFP module installed.
Caution
When pulling the tab to remove the SFP module, be sure to pull in a straight outward motion so you
remove the SFP module from the port in a parallel direction. Do not twist or pull the tab, because you
might disconnect it from the SFP module.
Installing a Mylar Tab SFP Module
To install this type of SFP module, follow these steps:
Step 1
Step 2
Attach an ESD-preventive wrist or ankle strap and follow its instructions for use.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing SFP Modules
Figure 5-6
Installing a Mylar Tab SFP Module
1
3
5
7
9
EXT CLK
ST
A
T
US
2
4
6
8
10
Note
Verify that the SFP modules are completely seated and secured in their assigned receptacles on the line
card by firmly pushing on each SFP module. If the SFP module is not completely seated and secured in
the receptacle, you will hear a click as the triangular pin on the bottom of the SFP module snaps into the
hole in the receptacle.
Actuator Button SFP Module
The actuator button SFP module includes a button that you push in order to remove the SFP module from
Figure 5-7
Actuator Button SFP Module
Removing an Actuator Button SFP Module
To remove this type of SFP module, follow these steps:
Step 1
Step 2
Attach an ESD-preventive wrist or ankle strap and follow its instructions for use.
Disconnect and remove all interface cables from the ports; note the current connections of the cables to
the ports on the line card.
Step 3
Gently press the actuator button on the front of the SFP module until it clicks and the latch mechanism
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing SFP Modules
Figure 5-8
Removing an Actuator Button SFP Module from a Port
7600
-
E
S
+
20G3CXL
1
3
5
7
9
EXT CLK
S
TA
MODULE
2
4
6
8
10
7600
-
E
S
+
20G3CXL
1
3
5
7
9
EXT CLK
S
TAT
U
S
ETH
ERN
4
6
8
10
Step 4
Step 5
Step 6
Grasp the actuator button between your thumb and index finger and carefully pull the SFP module from
the port.
Place the removed SFP module on an antistatic mat, or immediately place it in a static shielding bag if
you plan to return it to the factory.
Protect your line card by inserting clean SFP module cage covers into the optical module cage when
there is no SFP module installed.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing SFP Modules
Installing an Actuator Button SFP Module
To install this type of SFP module, follow these steps:
Step 1
Step 2
Attach an ESD-preventive wrist or ankle strap and follow its instructions for use.
Line up the SFP module with the port and slide it in until the actuator button clicks into place. (See
Figure 5-9.) Be sure not to press the actuator button as you insert the SFP module because you might
inadvertently disengage the SFP module from the port.
Figure 5-9
Installing an Actuator Button SFP Module
3
5
7
9
EXT CLK
ST
A
T
US
ETHERNET SER
V
ICES
M
2
4
6
8
10
Note
Verify that the SFP modules are completely seated and secured in their assigned receptacles on the line
card by firmly pushing on each SFP module. If the SFP module is not completely seated and secured in
the receptacle, you will hear a click as the triangular pin on the bottom of the SFP module snaps into the
hole in the receptacle.
Slide Tab SFP Module
The slide tab SFP module has a tab underneath the front of the SFP module that you use to disengage
Figure 5-10
Slide Tab SFP Module
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing SFP Modules
Removing a Slide Tab SFP Module
To remove this type of SFP module, follow these steps:
Step 1
Step 2
Attach an ESD-preventive wrist or ankle strap and follow its instructions for use.
Disconnect and remove all interface cables from the ports; note the current connections of the cables to
the ports on the line card.
Step 3
Step 4
Grasp the SFP module between your thumb and index finger.
With your thumb, push the slide tab on the bottom front of the SFP module in the direction of the line
Figure 5-11
Disengaging the Slide Tab
Step 5
Caution
You must disengage the SFP module by pushing on the slide tab before you can pull out the SFP module.
If you pull on the SFP module without disengaging the tab, you can damage the SFP module.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing SFP Modules
Figure 5-12
Removing a Slide Tab SFP Module
1
3
5
7
9
EXT CLK
S
TAT
U
ETHERNET SE
V
ICES
MODU
2
4
6
8
10
Step 6
Step 7
Place the removed SFP module on an antistatic mat, or immediately place it in a static shielding bag if
you plan to return it to the factory.
Protect your line card by inserting clean SFP module cage covers into the optical module cage when
there is no SFP module installed.
Installing a Slide Tab SFP Module
To install this type of SFP module, follow these steps:
Step 1
Step 2
Attach an ESD-preventive wrist or ankle strap and follow its instructions for use.
Hold the SFP module with the hardware label facing up.
Caution
Step 3
The SFP module must be inserted with the hardware label facing up to avoiding damaging the module
or the line card.
Insert the SFP module into the appropriate slot and gently push on it until it snaps into the slot tightly.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing XFP Modules
Figure 5-13
Installing a Slide Tab SFP Module
7600
-
E
S
+
20G3CXL
1
3
5
7
9
EXT CLK
S
TAT
U
2
4
6
8
10
Note
Verify that the SFP modules are completely seated and secured in their assigned receptacles on the line
card by firmly pushing on each SFP module. If the SFP module is not completely seated and secured in
the receptacle, you will hear a click as the triangular pin on the bottom of the SFP module snaps into the
hole in the receptacle.
Removing and Installing XFP Modules
Note
The dual LC connector on the XFP transceiver modules support network interface cables with either
Physical Contact (PC) or Ultra-Physical Contact (UPC) polished face types. The dual LC connector on
the XFP transceiver modules do not support network interface cables with an Angle Polished Connector
(APC) polished face type.
The 10-Gigabit XFP transceiver module is a hot-swappable I/O device that plugs into 10-Gigabit ports.
(See Figure 5-14.) The XFP transceiver module connects the electrical circuitry of the system with the
optical network.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing XFP Modules
Figure 5-14
10-Gigabit XFP Transceiver Module
3
4
5
1
2
6
1
2
3
Transmit optical bore
4
5
6
Bale clasp (locked position)
Dust plug
Receive optical bore
Transceiver socket connector
Bale clasp (unlocked position)
Installing the 10-Gigabit XFP Transceiver Module
Caution
The XFP transceiver is a static-sensitive device. Always use an ESD wrist strap or similar individual
grounding device when handling XFP transceivers or coming into contact with system modules.
To install an XFP transceiver, follow these steps:
Step 1
Step 2
Remove the XFP transceiver from its protective packaging.
Note
Do not remove the optical bore dust plugs until directed to do so later in the procedure.
Check the label on the XFP transceiver body to verify that you have the correct model for your network.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing XFP Modules
Step 3
Position the XFP transceiver in front of the XFP socket opening on the module. Slide the XFP transceiver
part of the way into the transceiver socket on the system module front panel.
Step 4
Step 5
Step 6
Remove the optical bore dust plug from the XFP transceiver.
Continue sliding the XFP transceiver into the socket until the XFP transceiver is mated with the
transceiver socket connector.
Step 7
Latch the XFP transceiver in the transceiver socket by pivoting the bale clasp down so that the bale clasp
Caution
Step 8
If the latch is not fully engaged, you may accidentally disconnect the XFP transceiver.
Immediately reinstall the dust plug in the XFP transceiver optical bores. Do not remove the dust plug
until you are ready to attach the network interface cable.
Figure 5-15
Installing the 10-Gigabit XFP Transceiver Module
760
0-E
S
+
2
T
G
3C
XL
A/L
EXT
CL
K
TUS
C
LAS
S
1
L
A
S
E
R
A/L
CL
K
1
ST
A
TUS
I
CES
C
LA
SS
1
L
A
S
E
R
Note
10-Gigabit XFP transceivers are keyed to prevent incorrect insertion.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing XFP Modules
Note
Before removing the dust plugs and making any optical connections, follow these guidelines:
•
•
•
Always keep the protective dust plugs on the unplugged fiber-optic cable connectors and the
transceiver optical bores until you are ready to make a connection.
Always inspect and clean the LC connector end faces just before making any connections. Refer to
the Tip on this page for a pointer to a fiber-optic inspection and cleaning white paper.
Always grasp the LC connector housing to plug or unplug a fiber-optic cable.
a. Remove the dust plugs from the optical network interface cable LC connectors. Save the dust plugs
for future use.
b. Inspect and clean the LC connector’s fiber-optic end faces.
Tip
For complete information on inspecting and cleaning fiber-optic connections, refer to this URL:
http://www.cisco.com/en/US/tech/tk482/tk607/technologies_white_paper09186a0080254eba.shtml
c. Remove the dust plugs from the XFP transceiver module optical bores.
d. Immediately attach the network interface cable LC connectors to the XFP transceiver module. (See
Figure 5-16 for cabling the XFP transceiver module.)
Figure 5-16
Cabling a10-Gigabit XFP Transceiver Module
7600
-
ES
+
2
TG3CXL
/L
A
EXT
CLK
1
ST
A
T
US
ETHERNET SER
VICES
MODU
LE
C
LASS 1
LASER
Removing the 10-Gigabit XFP Transceiver Module
Caution
The XFP transceiver is a static-sensitive device. Always use an ESD wrist strap or similar individual
grounding device when handling XFP transceivers or coming into contact with modules.
If you are removing an XFP transceiver, follow these steps:
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing XFP Modules
Step 1
Disconnect the network interface cable from the XFP transceiver connectors. Immediately reinstall the
dust plug in the fiber-optic cable LC connector.
Step 2
Step 3
Pivot the XFP transceiver bale clasp up to release the XFP transceiver from the socket. (See Figure 5-17.)
Slide the XFP transceiver out of the socket. Pivot the bale clasp down and immediately install the dust
Step 4
Immediately place the XFP transceiver in an antistatic bag.
Figure 5-17
Removing the 10-Gigabit XFP Transceiver
7600
-E
S
+
2T
G
3CXL
A/L
EXT
U
S
CL
A
SS
1
L
A
S
E
R
760
0-
ES
+
2T
G
3C
XL
A/L
1
M
O
DUL
E
CL
A
S
S
1
L
AS
E
R
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing and Removing SFP and XFP Modules
Removing and Installing XFP Modules
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
5-16
Download from Www.Somanuals.com. All Manuals Search And Download.
C H A P T E R
6
Troubleshooting
This chapter describes how to troubleshoot the installation of the Cisco 7600 Series Ethernet Services +
line cards on the Cisco 7600 series routers. This chapter contains the following sections:
•
•
•
•
•
•
Troubleshooting Installation Issues
This section describes troubleshooting the installation of the Cisco 7600 Series ES+ line card. Possible
problems, observations and comments, and solutions are indicated for the following troubleshooting
symptoms:
•
•
Cisco 7600 Series ES+ line card transitions repeatedly from on to off
Cisco 7600 Series ES+ line card is deactivated
Cisco 7600 ES+ Line Card Transitions Repeatedly From On to Off
Possible Problem
Observations and Comments
Solutions
Cisco 7600 Series ES+ line
card is booting up; this is
normal operation
Cisco 7600 Series ES+ line card Wait 30 seconds until the boot process completes and the
STATUS LED alternates green, STATUS LED stays on.
amber, or off
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Troubleshooting
Troubleshooting Installation Issues
Cisco 7600 ES+ Line Card Transitions Repeatedly From On to Off
Possible Problem
Observations and Comments
Solutions
Cisco 7600 Series ES+ line
Cisco 7600 Series ES+ line card Follow the recommended action for the displayed error
card does not go beyond the STATUS LED transitions
message.
bootup stage
continue and alternates green,
amber, or off
Cisco 7600 Series ES+ line
card is not up to date
During Cisco 7600 Series ES+
line card initalization, the need
to update the FPGA is
Follow the system prompts to update the FPGA image.
If the Cisco 7600 Series ES+ line card is cycling because
of an FPD problem, the most likely cause is a FPD failure
or that the FPD package file is not present.
automatically detected
For more information about performing FPD upgrades,
refer to the “Upgrading Field-Programmable Devices”
chapter in the Cisco 7600 Series Router SIP, SSC, and SPA
Software Configuration Guide .
Cisco 7600 ES+ Line Card Is Deactivated
Possible Problem
Observations and Comments
Solutions
Cisco 7600 Series ES+ line
Output of the show diag slot
Follow this procedure:
card is not fully seated in the command
chassis slot
•
Remove the Cisco 7600 Series ES+ line card from the
slot.
STATUS LED is off
•
Inspect the Cisco 7600 Series ES+ line card. Verify
there are no bent pins or parts and that there is nothing
that could prevent a good connection.
•
Insert the Cisco 7600 Series ES+ line card into the
chassis slot.
Cisco 7600 Series ES+ line
card is not at the minimum
hardware revision level
Error message indicating the
Cisco 7600 Series ES+ line card
is not at the minimum FPGA
revision level
Follow the FPD upgrade process to update the FPGA.
For more information about performing FPD upgrades,
refer to the “Upgrading Field-Programmable Devices”
chapter in the Cisco 7600 Series Router SIP, SSC, and SPA
Output of the show hw-module Software Configuration Guide .
subslot fpd command
Output of the show diag slot
command
STATUS LED is off
Troubleshooting Line Card Power Issues
Table 6-1 provides solutions for troubleshooting line card issues.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Troubleshooting
Troubleshooting Installation Issues
Table 6-1
Troubleshooting Line Card Power Issues
Problem
If a line card fails to operate or power up
Solution
1. Ensure that the card is seated firmly in the
slot.
2. Ensure that you have placed the gold edge of
the PCB in the guide rails of the chassis. This
prevents damage to the connector placed at
the rear side the board.
3. Check whether the ejector levers are latched
and that the captive screws are fastened
properly. If you’re uncertain, unlatch the
levers, loosen the screws, and attempt to reset
the supervisor again.
4. Examine the power supply to see whether the
complete chassis is receiving power.
5. Use the show power command to confirm if
the chassis has sufficient power to initiate the
new inserted line card.
6. Use the status LED on the line card to verify
the correct installation of the card. If the card
is installed correctly, the Status LED turns
green.
7. Ensure that you have installed the line cards
in their designated slots.
Note
All line cards can be inserted in all the
slots of chassis; however 7613 chassis has
exceptions. Dual fabric channel line cards
such as (ES20 and ES+ cards) can be
inserted only in 9 to13 slots of 7613
chassis.
Miscellaneous Line Card Issues
Table 6-2 provides solutions for troubleshooting line card issues.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Troubleshooting
Troubleshooting Installation Issues
Table 6-2
Troubleshooting Miscellaneous Line Card Issues
Solution
• When multiple line cards are inserted in the
Problem
Insufficient power
7600 chassis, some cards may not be able to
power up due to insufficient power. If the
power required by the line card exceeds the
power available in the system, the line card is
denied power and is shut down. In such a
case, use the show power command to verify
how much power is used and available.
•
Execute the command in the configuration
mode to deny power to a line card.
Router# configure terminal
Router(config)# no power enable module
<slot_number>
On doing this, the power consumed by the line
card before turning it OFF, is returned to the total
power available in the system. This is handy in
bringing up another line card. If you have
manually disabled power to a line card, you can
enable it with the following config mode
command:
Router(config)# power enable module
<slot_number>
Line card image not bundled in the IOS image
•
For a line card to bootup, the line card image
has to be bundled in the IOS image. Not all
line cards are supported with every image. A
line card does not bootup if its image is not
bundled with the system image. Execute the
show power and dir sup-microcode
commands to determine if the line card image
is bundled with the IOS image.
Find Master Timer expiry
•
•
This problem occurs when the RP does not
process the Find Master Messages in time, or
line card crashes or is unable to download the
image from the supervisor.
If one of the CPUs is not able to load the
image from the SP, try with a different image
and if the issue persists, replace the flexwan.
If any of the CPUs has crashed, collect the
crash information data to analyze further.
Faulty hardware
•
This following message indicates that the
module software cannot read the module
hardware version. This condition indicates a
hardware error.
Note
Bad hardware can also be a reason for the
line card not booting up. There are no
specific pointers which indicate that the
line card hardware is bad. But if none of
the above reasons match the failure of the
line card, it could a bad hardware issue.
00:02:51: %CWPA-2-BAD_HWVERS: Unable to
determine board hardware version
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Troubleshooting
Troubleshooting Installation Issues
Problem
Solution
SCP Keepalive Failure
•
The SP and the MSFC periodically poll each
individual LC in the chassis for its health via
SCP keepalives. Each LC in turn, must
respond within a certain amount of time
(dictated by the SCP keepalive timer) to
indicate its health. If the LC fails to respond
to the keepalives within the stipulated period
of time, the MSFC assumes that there is an
issue with the LC and power cycles it. When
the LC comes back online, the SCP
keepalives are resumed.
•
•
•
A line card might be unable to respond to the
scp keepalives under situations of extreme
stress when the CPU is busy with higher
priority tasks, such as packet switching,
interrupt processing etc.
Execute the show scp status and show scp
line cards command to gather detailed
information about the SCP process and health
of each LC. A show diagbus indicates any
errors with the LC.
Execute the test scp line card keepalive
disable exec command on the RP console to
disable the SCP keepalive timer and debug
LC issues. To prevent the LC from being
power cycled and losing its information,
ensure that you disable the SCP keepalives
for some time.
Line Card in ROM monitor
•
Linecards have a ROMMON variable
DL_DISABLE depending on which line card
auto boots or remains in ROMMON waiting
for manual boot. If DL_DISABLE is set to 0,
line card does not boot automatically but
waits for the user to manually boot with
respective line card image (from line card
console). Line card auto boots only if
DL_DISABLE=1. When DL_DISABLE=0
and line card doe not initialize, SCP
Keepalive Failure messages appear on RP
console.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Troubleshooting
Troubleshooting Installation Issues
Problem
Solution
•
SCP Download Failures
A line card is reset by the SP with messages
that SCP download failed or module reloaded
during reset. This occurs at the time of bootup
with a heavy configuration and a many line
cards. Execute the debug cwan oir command
to check the RP status. When a line card sends
a Find Master to the RP, some of the messages
are sent to SP to confirm if the module is
online. If the message fails to reach the SP,
then SP resets the module with message that
SCP download has failed. If the line card,
does not receive the response in the time, the
line card resets itself.
•
Reload the line card and connect the LC
console and check the status. If there is a
problem with ROMMON download of the
image from the SP, then the ROMMON of the
line card should then be upgraded to the latest
version. If a bay crashes, collect the stack
trace to identify problem.
An SCP ping is sent every two seconds to all the
line cards. If no response is received after three
pings (that is after 6 seconds), it is counted as the
first failure. After 25 such successive failures, that
is after 150 seconds of not receiving a response
from the line card, the SUP power cycles that line
card. After every 30 seconds, the following error
message is seen on the router:
Error Message %CPU_MONITOR-SP-6-NOT_HEARD
: CPU_MONITOR messages have not been
heard for 61 seconds [2/0]
%CPU_MONITOR-SP-6-NOT_HEARD:
CPU_MONITOR messages have not been
heard for 151 seconds [2/0]
%CPU_MONITOR-SP-6-NOT_HEARD:
CPU_MONITOR messages have not been
heard for 61 seconds [2/0]
%CPU_MONITOR-SP-6-NOT_HEARD:
CPU_MONITOR messages have not been
heard for 151 seconds [2/0]
After 150 seconds, the module gets power cycled
with these syslogs:
%CPU_MONITOR-SP-3-TIMED_OUT:
CPU_MONITOR messages havefailed,
resetting module [2/0]
%OIR-SP-3-PWRCYCLE: Card in module
1, is being power cycled
off
(Module not responding to Keep
Alive polling)
%OIR-SP-3-PWRCYCLE: Card in module
2, is beingpower-cycled off
(Heartbeat Messages Not Received
From Module)
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
6-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Troubleshooting
Using debug Commands
Troubleshooting ES Plus Line Card States
Table 6-3 provides solutions for troubleshooting line card issues.
Table 6-3
Troubleshooting Line Card States
Problem
Troubleshooting Line Card States
Solution
•
LED on the line card front panel is green
indicating that the that line card is up and
running with IOS.
•
The show module command shows the status
of line card slot as Ok and the status of the
Distributed Forwarding submodule as Ok
indicating that supervisor recognizes the line
card and if the line card is powered up and
online in the C7600 system or not.
•
•
LED on the SPA front panel is green.
The show hw-module subslot x/y oir
[internal] command indicates that the SPA
operation status is Ok..
•
•
The show running-config command shows
interfaces for the line card and if the
controllers for the installed SPAs (if any) are
installed.
The show ip interface brief command shows
the configured interfaces for the line card if
they are ready for configuration.
Using debug Commands
The debug hw-module subslot command is intended for use by Cisco Systems technical support
personnel. For more information about the debug hw-module subslot command, see the Cisco 7600
Series Router SIP, SSC, and SPA Software Configuration Guide .
Caution
Because debugging output is assigned high priority in the CPU process, it can render the system
unusable. For this reason, use debug commands only to troubleshoot specific problems or during
troubleshooting sessions with Cisco technical support staff. Moreover, it is best to use debug commands
during periods of lower network traffic and fewer users. Debugging during these periods decreases the
likelihood that increased debug command processing overhead will affect system use.
For information about other debug commands supported on the Cisco 7600 Series ES+ line card and to
view the explanations and recommended actions for the Cisco 7600 series router error messages,
including messages related to the Cisco 7600 Series ES+ line card, refer to the following documents:
•
•
Cisco IOS Release 12.2 SR Command References
Cisco 7600 Series Cisco IOS System Message Guide, 12.2SR
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Troubleshooting
Packing a Cisco 7600 ES+ Line Card for Shipment
Packing a Cisco 7600 ES+ Line Card for Shipment
This section provides step-by-step instructions for packing a Cisco 7600 Series ES+ line card for
shipment. Before beginning this procedure, you should have the following original Cisco Systems
packaging materials:
•
•
•
•
Static shielding bag
Smaller inner carton
Larger exterior carton
Two foam packing cushions
Caution
The Cisco Systems original packaging is to be used for the shipment of all Cisco 7600 Series ES+ line
cards. Failure to properly use Cisco Systems packaging can result in damage or loss of product.
Warning
Note
During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself.
These instructions assume that the Cisco 7600 Series ES+ line card has been removed from the router
according to the recommended procedures specified in this guide.
To pack a Cisco 7600 Series ES+ line card for shipment, perform the following steps:
Step 1
Step 2
Insert the Cisco 7600 Series ES+ line card into the static shielding bag.
Insert the bagged Cisco 7600 Series ES+ line card into the smaller inner carton. Be careful to position
the Cisco 7600 Series ES+ line card so that the bottom motherboard lip is held by the packaging cutout.
Step 3
Step 4
Close the smaller inner carton and tape the sides closed.
Place the sealed smaller inner carton containing the Cisco 7600 Series ES+ line card into the two foam
packing cushions (they only fit one way).
Step 5
Place the sealed smaller inner carton and packing cushions into the larger exterior carton, and seal the
larger exterior carton with tape for shipment.
Cisco 7600 Series Ethernet Services Plus Line Card Hardware Installation Guide
OL-16146-10
6-8
Download from Www.Somanuals.com. All Manuals Search And Download.
|