Carpet Extractor
Model:
10080480
Operating Instructions (ENG)
86302100-J
10/17/08
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
PARTS LIST & SERIAL NUMBERS
Machine Data Log/Overview................................2
Table Of Contents................................................3
Brush Deck........................................................ 5-1
Brush Deck Motor.............................................. 5-3
Brush Deck Mounting........................................ 5-5
Control Panel.....................................................5-7
Decal ................................................................. 5-9
Hand Tool..........................................................5-11
Handle............................................................... 5-13
Handle Bracket.................................................. 5-15
Handle Mounting ............................................... 5-17
Handle Release Lever....................................... 5-19
Recovery Tank .................................................. 5-21
Solution.............................................................. 5-23
Solution Tank .................................................... 5-25
Vac Shoe........................................................... 5-29
Vac Shoe Mounting........................................... 5-31
Vacuum ............................................................. 5-33
Wheel & Axle..................................................... 5-35
Wiring Diagram.................................................. 5-37
Suggested Spare Parts ..................................... 5-39
Serial Numbers..................................................5-40
Warranty
HOW TO USE THIS MANUAL
How To Use This Manual.....................................1-1
SAFETY
Important Safety Instructions ............................ 2-1
Hazard Intensity Level....................................... 2-2
Grounding Instructions...................................... 2-3
Safety Label Location........................................ 2-4
OPERATIONS
Technical Specifications.................................... 3-1
How The Machine Works.................................. 3-3
Components...................................................... 3-4
Controls............................................................. 3-5
Filling Solution Tank.......................................... 3-6
Pre-run Setup.................................................... 3-7
Operating the Machine...................................... 3-9
Using the Hand Tool ......................................... 3-12
MAINTENANCE
Service Schedule .............................................. 4-1
Maintenance Components................................ 4-2
Periodic, Daily & Regular Maintenance ........... 4-3
Circuit Protection............................................... 4-4
Scrub Deck........................................................ 4-5
Scrub Brushes................................................... 4-6
Vacuum............................................................. 4-7
Machine Troubleshooting.................................. 4-8
86302100 CLIPPER DUO 10/17/08
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THIS MANUAL
The SAFETY section contains important information
regarding hazardous or unsafe practices of the
machine. Levels of hazards are identified that could
result in product damage, personal injury, or severe
injury resulting in death.
This manual contains the following sections:
-
-
-
-
-
HOW TO USE THIS MANUAL
SAFETY
OPERATIONS
MAINTENANCE
PARTS LIST
The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.
The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.
The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition. They are
listed in this general order:
Parts may be ordered from authorized dealers.
When placing an order for parts, the machine model
and machine serial number are important. Refer to
the MACHINE DATA box which is filled out during
the installation of your machine. The MACHINE
DATA box is located on the inside of the front cover
of this manual.
-
-
-
Periodic
Daily/Regular
Troubleshooting
The PARTS LIST section contains assembled parts
illustrations and corresponding parts list. The parts
lists include a number of columns of information:
MODEL _____________________________________
DATE OF PURCHASE ________________________
SERIAL NUMBER ____________________________
SALES REPRESENTATIVE # ___________________
-
-
REF – column refers to the reference
number on the parts illustration.
PART NO. – column lists the part
number for the part.
-
-
PRV NO. – Reference number.
The model and serial number of your machine are
located where shown.
QTY – column lists the quantity of the
part used in that area of the machine.
DESCRIPTION – column is a brief
description of the part.
-
-
SERIAL NO. FROM – If this column has
an (*) and a Reference number, see the
SERIAL NUMBERS page in the back of
your manual. If column has two asterisk
(**), call manufacturer for serial number.
The serial number indicates the first
machine the part number is applicable
to. The main illustration shows the most
current design of the machine. When a
boxed illustration is shown, it displays
the older design.
-
NOTES – column for information not
noted by the other columns.
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.
: The manual part number is located on the
NOTE
lower left corner of the front cover.
86302100 CLIPPER DUO 06/06/08
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
This machine is for commercial use.
To reduce the risk of fire, electric shock, or injury:
Connect to a properly grounded outlet. See Grounding Instructions.
Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or
service.
Use only indoors. Do not use outdoors or expose to rain.
Do not allow machine to be used as a toy. Close attention is necessary when used by or near children.
Use only as described in this manual. Use only manufacturer’s recommended components and attachments.
Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the
machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into
water, return it to an authorized service center.
Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp
edges or corners.
Do not run machine over cord. Keep cord away from heated surfaces.
Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.
Do not handle the electrical plug or machine with wet hands.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.
This machine is intended for cleaning carpet only.
Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
This machine is not suitable for picking up health endangering dust.
Turn off all controls before unplugging.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near
flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops
and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
If foam or liquid comes out of machine, switch off immediately.
SAVE THESE INSTRUCTIONS
86302100 CLIPPER DUO 10/02/07
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR
SAFETY. The level of hazard intensity is determined by the following definitions:
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property
damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating
condition. Following is information that signals some potentially dangerous conditions to the operator or the
equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on
the machine. Please take the necessary steps to train the machine operating personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use
Windsor approved replacement parts.
86302100 CLIPPER DUO 10/02/07
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
120 VOLT MODELS:
GROUNDING INSTRUCTIONS
This appliance is for use on a nominal 120-volt
circuit, and has a grounded plug that looks like the
plug in “Fig. A”. A temporary adaptor that looks like
the adaptor in “Fig. C” may be used to connect this
plug to a 2-pole receptacle as shown in “Fig. B”, if a
properly grounded outlet is not available. The
temporary adaptor should be used only until a
properly grounded outlet (Fig. A) can be installed by
a qualified electrician. The green colored rigid ear,
lug, or wire extending from the adaptor must be
connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the
adaptor is used, it must be held in place by a metal
screw.
THIS PRODUCT IS FOR COMMERCIAL
USE ONLY.
ELECTRICAL:
In the USA this machine operates on a standard 15
amp 120V, 60 hz, A.C. power circuit. The amp,
hertz, and voltage are listed on the data label found
on each machine. Using voltages above or below
those indicated on the data label will cause serious
damage to the motors.
EXTENSION CORDS:
If an extension cord is used, the wire size must be at
least one size larger than the power cord on the
machine, and must be limited to 50 feet (15.5m) in
length.
Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. Check with a qualified electrician
or service person if you are in doubt as to
whether the outlet is properly grounded. Do not
modify the plug provided with the appliance - if it
will not fit the outlet, have a proper outlet
installed by a qualified electrician.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should
malfunction or break down, grounding provides a
path of least resistance for electric current to reduce
the risk of electric shock. This appliance is equipped
with a cord having an equipment-grounding
conductor and grounding plug. The plug must be
inserted into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
GROUNDED
OUTLET BOX
GROUNDED
OUTLET
ADAPTER
TAB FOR
METAL SCREW
GROUNDING SCREW
GROUNDING
PIN
(A)
(B)
(C)
86302100 CLIPPER DUO 10/02/07
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SAFETY LABEL LOCATION
NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become
illegible, promptly replace them.
WARNING LABEL
PART NUMBER 86242230
PRV NO 500009
WARNING LABEL
EXPLOSION FRENCH
PART NUMBER 86310500
86302100 CLIPPER DUO 06/06/08
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
TECHNICAL SPECIFICATIONS
ITEM
DIMENSION/CAPACITY
Construction
Vacuum Motor
Steel chassis with rotationally molded polyethylene tanks
Three stage, bypass, 1.5 hp (1,119 watts), 100 cfm
(2.8m³/min), 120” (3050 mm) waterlift
100 psi (7 bar) – Restorative
Solution Pump
50 psi (3.5 bar) - Interim
Brush Motor
Brushes
1/2 hp (604 watts) AC with circuit breaker protection
2 x 16” (406 mm), ABS core, Perform Alert™ bristle spiral
pattern
Cleaning Path
Cleaning Rate
16” (40.6 cm)
Interim – 10,560 ft²/hr (981 m²/hr)
Restorative – 3,520 ft²/hr (327 m²/hr)
Interim - 0.09 gpm ( 0.37 lpm)
Restorative – 1.0 gpm (37.8 lpm)
Interim – One quick-disconnect jet
Restorative - One quick-disconnect jet
10 gallons ( 37.8 l)
Flow Rate
Solution Spray
Solution Tanks
Recovery Tank
Vacuum Shoe
Wheels
Power Cable
Weight
10 gallons (37.8 l)
18” (458 mm) wide, cast aluminum
10” (254 mm) non-marking rubber
50’ (15 m) detachable
166 lbs (75.3 kg) with cord
86302100 CLIPPER DUO 10/02/07
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
TECHNICAL SPECIFICATIONS
ITEM
MEASURE
Height
Length
Width
Width of scrub path
43 inches (1092 mm)
40.5 inches (1029 mm)
22 inches (559 mm)
16 inches (406 mm)
HEIGHT
LENGTH
WIDTH
SPECIAL NOTES:
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with
appliance.
The sound pressure level at the operator’s ear was
measured to be 73.7 dBA. This was a nearfield, broad-band
measurement taken in a typical industrial environment on a
tile floor. This appliance contains no possible source of
impact noise. The instantaneous sound pressure level is
below 63 Pa.
The weighted root mean square acceleration at the
operator’s arms was measured to be below 2.5m/s2 . This
was a tri-axial, third-octave-band measurement made during
normal operation on a composite tile floor. The
measurement and related calculations were made in
accordance with ISO 5349-1.
8630210 CLIPPER DUO 05/08/08
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
The function of the scrub system is to scrub the
HOW THIS MACHINE WORKS
carpet, mix the cleaning solution with the soil and lift
and groom the carpet pile. The scrub system
consists of two cylindrical brushes, motor, and
controls. The brushes scrub the carpet as the motor
drives the brushes. The counter-rotating action of
the brushes grooms the carpet pile.
This carpet extractor is an electrical powered,
portable carpet extractor intended for commercial
use. The appliance sprays a cleaning solution onto
the carpet agitates the wet carpet, and then extracts
the soiled solution back into the unit’s recovery tank.
The appliance is fitted with and a hand tool for
cleaning upholstery and stairs.
The function of the recovery system is to vacuum the
soiled water back into the recovery tank. The
recovery system consists of the vacuum shoe,
vacuum motor, float ball filter, recovery tank and
controls. The vacuum shoe extracts the dirty
solution from the carpet as the machine moves
forward. The vacuum motor provides suction to
draw the dirty solution off the floor and into the
recovery tank. The float ball filter protects the
vacuum fan from debris and foam. The recovery
tank stores the dirty solution.
The machine is designed to maintain your carpet
using the Encapsulating Interim Carpet Cleaning
Process. By using the Interim Carpet Maintainer in
conjunction with Windsor Red Carpet Encapsulating
Interim Cleaning (W450-4) or Encapsulating Interim
Cleaning with Carpet Protection (W455-4) chemical
solution, you can perform a regular light cleaning
and grooming of your carpet very quickly, and have
the carpet dry and ready for traffic within 30 minutes.
The function of the operator control system is to
allow the operator to select the desired function to
perform.
The machine is also designed to restore your carpet
using carpet extraction chemicals. The machine is
designed to apply cleaning solution onto carpeted
floor, scrub the carpet with two counter-rotating
brushes, and then vacuum the soiled water back into
the recovery tank.
CAUTION: This appliance is not suitable for picking
up hazardous dust.
The machine's primary systems are the solution
system, scrub system, recovery system and operator
control system.
The function of the solution system is to store mixed
solution and deliver solution to the appropriate spray
jet. The solution system consists of the solution
tank, strainer, extraction pump and interim pump,
solenoid valve, spray jets, accessory hand tool, and
controls. The solution tank stores solution until it is
delivered through the strainer to the appropriate
pump. The solenoid valve allows flow from the
extraction pump to the extraction nozzle or stops
flow at the extraction nozzle so that the accessory
hand tool can be used. The interim pump provides
flow directly to the interim nozzle. The strainer
protects the pump from debris. The solution pumps
control the cleaning solution flow.
86302100 CLIPPER DUO 05/08/08
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS-COMPONENTS
1
2
3
4
8
6
7
5
9
1. Control Panel
6. Solution Fill Cover
7. Solution Drain Hose
8. Solution Tank
2. Recovery Dome
3. Recovery Drain Hose
4. Recovery Tank
5. Scrub Deck
9. Vacuum Shoe
86302100 CLIPPER DUO 10/02/07
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS-COMPONENTS
3
5
1
2
4
6
7
1. Hand Tool Switch
2. Main Switch
3. Light Cleaning
4. Deep Cleaning
5. Continuous Spray
6. Intermittent Spray
7. Intermittent Spray Buttons
86302100 CLIPPER DUO 10/02/07
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS-FILLING THE SOLUTION TANK
Do not put defoamer, solvents, spotter or
prespray chemicals in the solution tank.
Do not allow water to spill into vacuum motor inlet.
Dry spills from top of solution tank.
REMOVE SOLUTION
FILL COVER
Use only the suitable chemicals listed below. Using
incompatible chemicals will damage the machine.
Damages of this type are not covered under warranty.
Carefully read ingredients on manufacturer’s label before
using any product in this machine.
CHEMICALS
Suitable Chemicals
Alkalis
Non-Compatible Chemicals
Aldehydes
STEP 1
Detergents
Hydroxides
Soaps
Aromatic Hydrocarbons
SP Butyls
Carbon Tetrachloride
Clorox*
ADD WATER
10 Gal.
(38 Lt)
Vinegar
Chlorinated Bleaches
Chlorinated Hydrocarbons
Lysol*
Methyl Ethel Ketone (MEK)
Perchorethylene (perc)
Phenolics
OR
Trichlorethylene
D-Limonene
STEP 2
ADD CLEANING
CHEMICAL PER
CHEMICAL LABELING
FILL LINE
STEP 3
REPLACE SOLUTION
FILL COVER
STEP 4
86302100 CLIPPER DUO 10/02/07
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS-PRE RUN SETUP
Remove electrical cord and literature from recovery
tank. Fill solution tank (see filling instructions).
STEP 1
Plug cord into grounded outlet. NOTE: Be sure
dome is seated on recovery tank, and float shut-
off is installed correctly.
STEP 2
Switch the cleaning mode switch to the desired
process.
A for the encapsulating Interim Carpet Cleaning
Process.
B for Deep Extraction.
STEP 3
Adjust handle to comfortable operating position. Tip
machine back by main handle to move to starting
point.
STEP 4
86302100 CLIPPER DUO 10/02/07
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS-PRE RUN SETUP
Lower machine to floor.
STEP 5
Select continuous setting to start solution spray or
select intermittent setting to enable use of trigger
switches to start solution spray.
The intermittent setting requires the operator to hold
any one of the three trigger switches in the “on”
position with the fingers, and is typically used in
small areas where short cleaning passes are made.
The continuous setting allows the operator to set the
switch in the “on” position with one touch, and is
typically used in large areas where long cleaning
passes are made.
STEP 6
Place main switch in machine cleaning mode to start
cleaning process.
86302100 CLIPPER DUO 10/02/07
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS-OPERATING THE MACHINE
2
1
1. This machine can be operated in either
direction. For smaller areas operate the machine
by pulling rearward.
2. For larger unobstructed areas, flip the handle
and use the machine’s brush assisted propelling
motion.
STEP 1
Start at wall closest to power outlet. For small areas,
pull straight back without pushing down on handle.
STEP 2
1 ft.
(30 cm)
Release intermittent trigger switches or turn off
continuous setting on solution switch approximately
1 foot before ending cleaning pass.
STEP 3
1 in.
(25mm)
Push down on handle to raise vacuum shoe and
brush before moving to the next cleaning pass.
Overlap brush contact area approximately 1 inch.
STEP 4
86302100 CLIPPER DUO 10/02/07
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS-OPERATING THE MACHINE
Start at wall closest to power outlet. For large areas
flip handle and operate machine in parallel passes,
overlapping brush path. Clean perimeter last.
ALTERNATE CLEANING PATH
During operation, observe the following: This
machine is equipped with clear dome to facilitate
operator viewing of dirty solution and vacuum air
flow.
VACUUM INTAKE
SOLUTION INTAKE
During operation, observe the vacuum intake. Large
amounts of water or foam entering the vacuum
system can damage the vacuum motor. If you notice
either condition, shut down the machine
immediately. Empty recovery tank and/or add
defoamer to recovery tank.
STEP 5
Use right side of machine for cleaning against walls.
STEP 6
CENTER
OFF
POSITION
SHUT
DOWN
After cleaning, turn off all controls, and carefully
unplug machine.
86302100 CLIPPER DUO 10/02/07
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS-OPERATING THE MACHINE
To speed drying, use a Windblower™ fan.
Empty recovery tank by releasing recovery drain hose.
Use a hose with cold water to clean out the recovery
tank. Also drain solution tank after each use.
RECOVERY
DRAIN HOSE
SOLUTION
DRAIN HOSE
STEP 7
86302100 CLIPPER DUO 10/02/07
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS-USING THE HAND TOOL
Use only acceptable accessory tools. See Optional
Accessories section.
To connect solution hose pull back collar and insert
over machine mounted fitting, then release collar to
lock into place. Solution connection can remain
connected at all times.
HAND TOOL
CONNECTION
SOLUTION QUICK
DISCONNECT
Disconnect vacuum hose and connect the hand tool
to hand tool connection as shown.
STEP 1
HAND TOOL POSITION
Select hand tool switch.
STEP 2
Squeeze handle on accessory tool to begin
cleaning.
STEP 3
86302100 CLIPPER DUO 10/02/07
3-12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE-SERVICE SCHEDULE
SERVICE SCHEDULE
MAINTENANCE
Check machine for cord damage
DAILY
*
WEEKLY
QUARTERLY
Check recovery dome and gasket for damage and
cleanliness
Check brushes – should be clean with no lint or
strings attached
*
*
Inspect vac shoe for blockage; remove fibers with
coat hanger, etc.
*
*
*
*
Check hoses for wear, blockages, or damage
Check handles, switches, and knobs for damage
Run one gallon of water through solution system
Clean out recovery tank, clean float screen and
check float valve to make sure it moves freely
Clean out solution
Clean outside of all tanks and check for damage
Run vac motor for at least one minute to allow motor
to dry
*
*
*
*
*
Store with dome off tank to allow the tank to dry
Check all bearings for noise
*
*
Check all gaskets for wear and leakage
Check pump pressure; observe spray pattern and
check with gauge if necessary
*
*
Check and clean solution screen
Check brush for wear; ensure bristles are not
damaged
*
*
*
Check condition of vac shoe and frame for damage
Check overall performance of machine
Check vac motor carbon brushes
Check belts for wear and replace as necessary
Check cables for fraying
*
*
*
4-1
86302100 CLIPPER DUO 10/02/07
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE-COMPONENTS
6
2
4
BOTTOM
3A
3B
1
5
RIGHT
LEFT
1. Vacuum Motor
4. Interim Solution Pump
5. Main Solution Pump
6. Float Shut-off
2. Solution Strainer
3A. Spray Jet-Extraction
3B. Spray Jet-Interim
86302100 CLIPPER DUO 10/02/07
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE-PERIODIC
PERIODIC MAINTENANCE
3. After each use, rinse tank with fresh water.
Periodically inspect the recovery tank and
decontaminate if necessary, using a Hospital
Grade Virucide or a 1-10 bleach to water
solution. Waste water should be disposed of
properly.
Twice a month, flush a white vinegar solution (One
quart vinegar to two gallons of water) or anti-
browning solution (mixed as directed) through the
extractor. This will prevent build-up of alkaline
residue in the system. If spray jets become clogged,
remove the spray tips, wash them thoroughly, and
blow-dry.
4. Check for and remove any lint or debris around
vac shoe.
NOTE: Do not use pins, wire, etc. to clean
nozzles as this could destroy spray pattern.
5. Check spray jets for full spray pattern.
6. Remove lint and dirt build-up from brush and
Periodically inspect all hoses, electrical cables and
connections on your machine. Frayed or cracked
hoses should be repaired or replaced to eliminate
vacuum or solution pressure loss. If the cable
insulation is broken or frayed, repair or replace it
immediately. Don’t take chances with electrical fire
or shock.
housing.
7. Check float and shut-off screen and clean as
necessary.
DAILY / REGULAR MAINTENANCE
NOTE: Before making any adjustments or repairs
to the machine, disconnect the power cord from
electrical source.
1. Empty unused cleaning solution from the
solution tank.
2. Flush pumping system with 4 or 7 liters of clean,
hot water.
4-3
86292100 CLIPPER DUO 10/02/07
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE-CIRCUIT PROTECTION
CIRCUIT BREAKERS
CIRCUIT BREAKERS
Circuit breakers interrupt the flow of power in the
event of an electrical overload. When a circuit
breaker is tripped, reset it by pressing the
exposed button. If a circuit breaker continues to
trip. The cause should be found and corrected.
15 Amp. Protects the vacuum motor.
8 Amp. Protects the brush motor.
86292100 CLIPPER DUO 10/02/07
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE-SCRUB DECK
1
3
4
2
1. Scrub Brush Motor
2. Scrub Brushes
3. Retaining Clip
4. Brush Installation Decal
86302100 CLIPPER DUO 10/02/07
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE-SCRUB DECK
SCRUB HEAD
SCRUB BRUSH REPLACEMENT
The dual cylindrical scrub head is designed to scrub
chemical into the carpet. The two counter rotating
brushes raise the pile of the carpet, giving it a lush
groomed appearance.
NOTE: See brush placement decal on brush
deck. (Black brush to rear of machine and white
brush to front of machine).
The rear brush is the stiffer brush and is intended to
scrub deeper and help propel the machine. It can be
identified by its black color.
WARNING: Only use the brushes provided with the
appliance or those specified in the instructions
manual. The use of other brushes may impair safety.
The front brush is the softer brush and is intended to
lift and groom the carpet pile. It can be identified by
the white bristles.
MAINTENANCE
Scrub brushes should be replaced as a set when
bristle length wears to height of yellow Perform
AlertTM bristles.
SCRUB BRUSH REMOVAL
1. Lift the drive side of the brush and push it onto
drive hub until a positive stop is felt. The brush
cannot be installed until the brush is fully seated
on the drive hub.
The scrub brushes are removed from the right side
of the machine.
2. Pull out on the bottom of the retaining clip.
3. Line up the end cap with the flats to each side.
1. Disconnect all power and unplug machine.
2. Tip the machine back.
4. Slide brush up into the retaining clip until it clicks
3. Pull out on the bottom of the retaining clip.
in place.
4. The brush assembly and end cap should drop
down. Then pull the brush down far enough to
clear the bottom of the housing.
5. Pull brush out with a rocking motion to free
brush from drive hub.
86302100 CLIPPER DUO 05/08/08
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE-VACUUM MOTOR
ONLY QUALIFIED
MAINTENANCE
PERSONNEL ARE TO PERFORM THE
Vacuum Motor Carbon Brushes Replacement
End Cap
FOLLOWING REPAIRSVACUUM MOTOR
REPLACEMENT
WARNING: The green
Carbon
ground wire must be
Brushes
1. Turn off all switches and unplug machine.
2. Remove recovery tank.
attached for safe operation.
See wiring diagram.
3. Remove the (2) screws that fasten the solution
tank to the frame, and tilt tank back to expose
the inside of the frame.
If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.
4. Locate the vacuum motor wires and disconnect
at the connector. Close the solution tank.
5. Remove the (6) screws holding the vacuum
motor cover to the solution tank.
6. Remove the vacuum motor.
7. Reverse process to install vacuum motor.
Important:
These brushes wear quicker as the length shortens due to
increased heat. Spring inside brush housing will damage
motor if brushes are allowed to wear away completely.
3
[9.5mm]
8
Periodically check the length of the carbon brushes. Replace
both carbon brushes when either is less than 3/8" (9.5mm)
long.
86302100 CLIPPER DUO 10/02/07
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE-TROUBLESHOOTING
PROBLEM
CAUSE
SOLUTION
Is the cord plugged in.
Plug in cord.
No Power, Nothing
Runs
Circuit breaker tripped in building.
Faulty switch.
Reset breaker.
Call for service.
Faulty power cord or pigtail.
Vacuum circuit breaker tripped.
Faulty main vacuum switch.
Loose wiring.
Call for service.
Reset breaker.
Vacuum Motor Will Not
Run
Call for service.
Call for service.
Faulty vac motor.
Call for service.
Debris lodged in vac shoe.
Dome gasket defective or missing.
Vacuum hose cracked or hose cuff loose.
Recovery tank full / float ball stuck in the
up position.
Remove debris from vac shoe.
Replace as necessary.
Replace or repair as necessary.
Turn off vac motor. Drain and rinse
recovery tank.
Vacuum Motor Runs
But Suction Is Poor
Pump switch in intermittent position.
Turn to continuous or use buttons on
handle
Poor Or No Water Flow
(Carpet Is Streaky)
Jets clogged or missing.
Solution filter clogged.
Clean using a vinegar /water solution or
replace.
Drain solution tank and clean solution
filter.
Faulty solenoid.
Call for service.
Main switch off or in hand tool mode.
Brush circuit breaker tripped.
Brush belt broken.
Turn main switch to machine mode.
Reset circuit breaker.
Replace as necessary.
Call for service.
Brush Does Not Spin
Faulty brush motor.
86302100 CLIPPER DUO 10/02/07
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
86302100 CLIPPER DUO 10/02/07
Download from Www.Somanuals.com. All Manuals Search And Download.
BRUSH DECK
86302100 CLIPPER DUO 10/02/07
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
BRUSH DECK
SERIAL NO.
FROM
REF PART NO.
PRV NO. QTY
DESCRIPTION
NOTES:
1
2
3
4
86223780
86224170
86012800
86012810
70896
730410
8
2
2
1
SCR, M4X8, SET, ISO4029,CP,BLK
SHAFT, 6.2MM BRUSH DRIVE
SHAFT ASM, BRUSH END CAP
SHAFT, ASM, DRIVE 16”
RING, 28MM INT SNAP
-
-
5
86223520
67598
3
PHOSPHATE
6
7
8
86223310
86215250
86224660
86173330
86014990
86215870
86012780
86216050
64116
11049
730393
87513
-
140914
-
12530
1
1
1
1
9
1
2
1
PULLEY, 5MM HTD, 18T, 12.7 ID
BELT, 2S 5MM HTD, 15W, 128T
SPRING, TENSIONER
WASHER, M5 FLAT, ISO7093 SS
SCR, M5X20, SHCS ISO4762, SS
BRKT, TENSIONER ARM
PULLEY ASM, 5MM HTD 22T
BRUSH, EXTRACTOR 16”
BRUSH, EXTRACTOR 16”
NATURAL
9
10
11
12
13A
13B
86295520
-
1
14
15
16
17
18
86223490
86224130
86219380
86294070
86012790
67468
730394
41546
2
1
1
1
2
RING, 10MM EXT SNAP, DIN 471
SHAFT, TENSIONER
HOUSING, BRUSH DRIVE
PULLEY, 36T 5MM HTD
SHAFT ASM, BRUSH DRIVE
SCR, M5X12, PHLP FHMS,
ISO7046, SS
-
-
19
86172970
70911
3
20
21
22
23
86222870
86217780
86219390
86173350
620103
32058
41548
87515
1
1
1
4
PLATE, BRUSH DRIVE COVER
EXTRUSION, DUAL BRUSH 16”
HOUSING, BRUSH CLIP
WASHER, M5, FLAT, ISO7089,SS
SCR, KA50X10, PT OHS,
WN14112, PLTD
24
86172980
70912
2
25
26
27
28
86224630
86277130
86215230
86294060
730380
70795
09161
-
2
7
1
1
SPRING, BRUSH CLIP
SCR, 5/16-18 X 1.00 CARRIAGE SS
BEARING, BRONZE FLANGED
PULLEY, 30T 5MM HTD
86302100 CLIPPER DUO 10/02/07
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
BRUSH DECK MOTOR
86302100 CLIPPER DUO 10/02/07
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
BRUSH DECK MOTOR
SERIAL NO.
NOTES:
FROM
REF PART NO.
PRV NO. QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
86273750
86173340
86010630
86215880
86222120
86222290
86217250
86217260
86172960
86225790
86005640
86002390
86198450
86276820
86216750
70011
87514
87013
140929
53274
57308
22105
22106
70910
87504
57030
20063
20005
70740
20098
6
6
6
2
1
3
2
1
2
3
3
1
3
3
1
SCR, 1/4-20 X 5/8 HHCS SS
WASHER, SPLIT LOCK, 1/4 SS
WASHER, 1/4 ID X 5/8 OD SS
BRKT, MOTOR MOUNT
MOTOR, 115V, 0.5HP, INDUCTION
NUT, 5/16-18 HEX NYLOCK SS
COUPLER, 1/2” JAW
COUPLER, SPIDER
SCR, SET, M6X8, SH, ISO4029,SS
WASHER, 5/16 X .63 SS
NUT, 10-32 HEX NYLOCK
CLAMP, 1.75” WORM GEAR X .312
CLAMP, 5/16 NYLON
SCR, 10-32 X 1/2 PTHMS BLK NP
CLAMP, WORM GEAR 40-64MM
86302100 CLIPPER DUO 10/02/07
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
BRUSH DECK MOUNTING
1
7
8
7
2
3
4
5
2
19
2
10
3
3
4
11
15
12
16
9
6
13
20
3
17
18
14
86302100 CLIPPER DUO 10/17/07
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
BRUSH DECK MOUNTING
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
DEFLECTOR, SPRAY
NUT, 5/16-18 HEX NYLOCK SS
WASHER, 5/16 FLAT SS
WASHER, THRUST .51 ID X 1 OD X .063
BRKT, DECK ARM CROSSBAR
BEARING, FLNGD, .314 ID X .502 OD
SCR, 5/16-18 X 1.00 CARRIAGE SS
BRKT, DECK ARM RIGHT
BRKT, LEFT DECK HANGER
BRKT, RIGHT DECK HANGER
NUT, 10-32 HEX NYLOCK
WASHER, #10 X 9/16 OD
BRKT, BRUSH DECK PIVOT
WASHER, 5/16 X .63 SS C
SCR, 1/4-20 X 1/2 PPHMS SS DL
COVER, BRUSH DECK MOTOR
SPACER, .500OD X .391ID X .400
CUSHION, BRUSH DECK
1
2
86302710
86270830
86010670
86259410
86296450
86228990
86277130
86295010
86294940
86294950
86270990
86010650
86071800
86225790
86006580
86301870
86008460
86296480
86295020
86271840
-
57023
87029
87206
-
1
11
13
4
3
4
5
1
6
7
8
09153
70795
-
4
8
1
9
-
1
10
11
12
13
14
15
16
17
18
19
20
-
1
4
4
2
1
2
1
2
57090
87018
141001
87504
70085
-
80102
-
2
1
1
-
BRKT, DECK ARM LEFT
NUT, 5/16-18 HEX NYLOCK THIN SS
57285
86302100 CLIPPER DUO 10/17/07
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL PANEL
22
7
15
13
17
1
14
16
7
8
19
6
9
11
4
19
3
2
12
23
21
25
5
20
24
18
10
25
86302100 CLIPPER DUO 07/09/08
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL PANEL
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
NOTES:
1
2
3
4
5
6
7
8
9
86002010
86001980
86215670
86308020
86173030
86173300
86005640
86172640
86223010
86301820
86224730
86224930
14942
14700
140839
-
70917
87495
57030
57507
62909
-
2
1
1
1
4
1
3
1
1
1
1
1
BOOT, 3/8 CIRCUIT BREAKER
BREAKER, 15A 250VAC 50VDC
BREAKER, 8A VDE CIRCUIT
GASKET, HANDLE CTRL PNL
SCR, M4 X 6, PHMS, ISO7045, PL
WASHER, M8, FLAT ISO7089, SST
NUT, 10-32 HEX NYLOCK
NUT, M8, NYLOCK, ISO7040, SST
PLATE, CONTROL PANEL
TRANSFORMER, 24V, 115V
SPRING, COMP, 12MM OD X 12.7MM
STRAIN RELIEF, 14/3 STRAIGHT
SWITCH, DPDT 2-POSITION
ROCKER
10
11
12
73939
730012
13
14
15
86007130
86007200
86007140
72128
72162
72130
1
1
1
SWITCH, DPDT3-POSITION
ROCKER
SWITCH, SPST 2- POSITION
ROCKER
16
17
18
19
20
21
22
23
24
25
86010640
86295700
86298820
86276820
86298690
86297750
86233170
86234110
86298810
86006620
87016
1
1
1
5
1
1
1
1
1
4
WASHER, #10 LOCK EXT STAR SS
BRKT, ELECTICAL SEPARATOR
BRKT, HANDLE TRANSFORMER
SCR, 10-32 X 1/2 PTHMS BLK NP
RELAY, 24VAC
CORD ASM, 14/3 X 22 PGTL
CLAMP, 3/8 NYLON UL/CSA
CORD SET, 14/3 SJTW-A X 50’ YLW
BRKT, HANDLE RELAY
-
-
70740
-
-
20054
23086
-
70127
SCR, 6-32 X 1/4 PPHMS SS
86302100 CLIPPER DUO 07/09/08
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
DECAL
5
1
2
3
4
86302100 CLIPPER DUO 10/17/07
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
DECAL
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
NOTES:
1
2
3
4
5
86221470
86244680
86004970
86298670
86295620
501208
501205
50990
1
1
1
1
1
LABEL, ACCESSORY
LABEL, CLIPPER DUO
LABEL, WINDSOR LOGO DOMED
LABEL, BRUSH INSTALL
LABEL, CTRL PNL CLP DUO
-
-
86302100 CLIPPER DUO 10/17/08
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
HAND TOOL
4
3
5
2
1
86302100 CLIPPER DUO 10/02/07
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
HAND TOOL
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
NOTES:
1
2
3
4
5
86200810
86293280
86293290
86293500
86293750
270-11
1
1
1
1
1
NIPPLE, 1/8 FPT QD FEM BRASS
HOSE, 1/4” RETRACTABLE
HOSE ASM, 38.1 X 711 BLK VAC
HANDTOOL ASM
-
-
-
-
RETAINER, SOLUTION HOSE
86302100 CLIPPER DUO 10/02/07
5-12
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE
3
1
5
1
1
2
10
8
7
6
4
9
86302100 CLIPPER DUO 10/17/08
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE
SERIAL NO.
FROM
REF PART NO.
PRV NO. QTY
DESCRIPTION
BEZEL, SWITCH
SPACER, HANDLE EXTRUSION
HANDLE, GRIP
SCR, M8X40, SHCS, ISO 4762, SST
SCR, KA40X20, PT OVAL, WN1412, PL
SCR, M5X12 SHCS GR 10.9 PLT
HOOK, UPPER, CORD
NOTES:
1
2
86215340
86224500
86218660
86223830
86173000
86293400
86218960
86218950
86218640
86218630
140318
730417
38353
70927
70914
-
3
4
1
1
3
4
1
2
1
1
3
4
5
6
7
8
9
10
41575
41574
38351
38350
HOOK, LOWER, CORD
HANDLE, EXTRUSION, LEFT
HANDLE, EXTRUSION, RIGHT
86302100 CLIPPER DUO 10/17/08
5-14
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE BRACKET
15
15
13
12
3
14
4
10
9
2
1
6
11
3
10
7
8
4
5
86302100 CLIPPER DUO 10/17/07
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE BRACKET
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
NOTES:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
86276800
86279170
86296830
86296860
86296880
86296890
86296920
86296970
86296980
86302860
86298840
86233170
86005640
86274400
86298830
70734
87093
5
6
2
2
1
1
1
1
1
2
1
1
1
4
2
SCR, 10-32 X 3/8 HHMS SS
WASHER, #10 X 1.0 FLAT
BRKT, HANDLE PIVOT
-
-
-
-
-
-
-
-
PLATE, HANDLE PIVOT LATCH
LEVER, HANDLE RELEASE LEFT
LEVER, HANDLE RELEASE RIGHT
BRKT, HANDLE TANK MOUNT
MECHANISM MOUNT, LEFT
MECHANISM MOUNT, RIGHT
SPRING, EXT .25D X 1.13L X .031W
SCR, 10.32 X 1.0 HHMS PLT
CLAMP, 3/8 NYLON UL/CSA
NUT, 10-32 HEX NYLOCK
-
20054
57030
70194
-
SCR, 1/4-20 X 5/8 BHCS
NUT, 10-32 LOCK DT 1/8 THK PLT
86302100 CLIPPER DUO 10/17/08
5-16
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE MOUNTING
2
8
6
2
4
7
5
3
1
4
86302100 CLIPPER DUO 10/02/07
5-17
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE MOUNTING
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
NOTES:
1
2
3
4
5
6
7
8
86274400
86006950
86276490
86010670
86295760
86295770
86297100
86297220
70194
70532
70670
87029
2
6
6
6
2
2
2
1
SCR, 1/4-20 X 5/8 BHCS
SCR, 10-32 X 1/2 PPHMS BLK NP
SCR, 5/16-18 X 5/8 HHCS SS
WASHER, 5/16 FLAT SS
CAP, HANDLE, OUTER
CAP, HANDLE, INNER
-
-
-
-
BRUSH, HANDLE CAP
PANEL, CONN. ACCESS
86302100 CLIPPER DUO 06/06/08
5-18
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE RELEASE LEVER
3
7
5
10
6
4
9
15
17
16
11
8
12
2
14
18
1
13
4
86302100 CLIPPER DUO 07/09/08
5-19
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE RELEASE LEVER
SERIAL NO.
NOTES:
FROM
REF PART NO.
PRV NO. QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
86215240
86215630
86216870
86008650
86218190
86218020
86221730
86222280
86295820
86221840
86222550
86222990
86173030
86293370
86224540
140971
14878
27973
80604
35371
35024
51053
57307
-
14833
66138
62891
70917
-
2
1
1
4
2
1
1
4
2
1
1
1
4
4
4
BEARING, FLANGE, 10M ID
BRACKET, LEVER, CONSOLE
CONSOLE, HANDLE
COTTER, 14” RING
GASKET, CONSOLE, TUBE
GASKET, LEVER, HANDLE
LEVER, PIVOT HANDLE
NUT, 10-32 HEX NYLOCK SS
PIN, LEVER SHAFT
PIN, LINKAGE
PIN, PIVOT, LEVER
PLATE, PIVOT, LEVER
SCR, M4 X 6, PHMS, ISO7045, PL
SCR, M8X70, HHCS, GR 10.9 PLT
SPACER, 8.5 ID X 45L
SPRING, COMP 18MM OD X 83 X
2
WASHER, THRUST .51 ID X 1
ODBRO
WELDMENT, PIVOT SHAFT,
LEVER
73588
16
17
18
86254970
86259400
86225950
730304
87205
89284
1
1
1
86302100 CLIPPER DUO 07/09/08
5-20
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOVERY TANK
1
2
7
8
6
3
9
5
10
4
11
86302100 CLIPPER DUO 10/02/07
5-21
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOVERY TANK
SERIAL NO.
FROM
REF PART NO.
PRV NO. QTY
DESCRIPTION
DOME, 2 HOSE
GASKET, DOME
FLOAT SHUT-OFF
NOTES:
1
2
3
86217680
86218180
86003630
28068
35370
34351
1
1
1
TANK, RECVRY, DK GRAY
(TRIMMED)
4
86299180
-
1
5
6
7
8
9
86297250
86006950
86004500
86004510
86002400
86296640
86233140
-
1
2
1
1
1
1
1
HOOK, WIREFORM, HANDTOOL
SCR, 10-32 X 1/2 PPHMS BLK NP
HOSE, CAP
70532
41390
41391
20064
-
HOSE, INSERT
CLAMP, 2.0” WORM GEAR X .312W
HOSE, 1.5 X 19.0 DRAIN
CLAMP, 2.0” WORM GEAR
10
11
20041
86302100 CLIPPER DUO 10/02/07
5-22
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLUTION
2
4
11
17
3
15
19
20
7
21
18
13
14
15
12
8
1
9
16
3
6
10
5
14
15
86302100 CLIPPER DUO 10/17/08
5-23
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLUTION
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
NOTES:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
86308240
86197420
86218360
86200280
86005640
86273930
86006520
86274290
86298840
86010650
86197940
86294700
86294720
86297930
86298120
86299120
86281100
86281980
86304620
86233150
86240530
-
1
1
2
1
4
2
2
2
4
4
1
1
1
4
10
1
1
1
1
3
1
GASKET, SOLUTION ASSY
ELBOW, 3/8 NPT STREET
GROMMET, 3/4 ID X 7/8 GROOVE
HOSEBARB, 3/8 MPT X 1/4 90D
NUT, 10-32 HEX NYLOCK
SCR, 8-32 X 1/2 PPHMS
SCR, 8-32 X 3/8 PPHMS SS
SCR, 10-32 X 3/8 PPHMS SS
SCR, 10-32 X 1 HHMS PLTD
WASHER, #10 X 9/16 OD
31026
36244
250-12
57030
70051
70052
70162
-
87018
40027
-
HOSEBARB, 3/8MPTX1/2 90D DL
BRKT, SOLUTION ASSY
ASSY, FRAME, SOLUTION
GROMMET, .50ID X .06
-
-
-
-
NUT, SPEED, #8-32
TERMINAL STRIP, 4-POS, .25
HOSE, 1/2ID WIRE BOUND X 7”
HOSE, 1/2D WIRE BOUND X 5”
ASSY, PUMP, 230V
CLAMP, 3/8 HOSE (D-SLOT)
HOSEBARB, 1/2 X 1/4 X 1/2, TEE
39274
39549
-
20042
40098
*SEE SERIAL NUMBER PAGE.
86302100 CLIPPER DUO 10/17/08
5-24
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLUTION
17
2
21
20
14
18
20
34
13
7
27
29
26
7
1
9
28
30
3
2
27
1
1
16
6
12
3
1
36
5
35
15
1
11
3
1
1
4
26
25
8
35
19
7
24
10
23
27
32
1
3
7
22
27
33
39
37
38
86302100 CLIPPER DUO 10/17/08
5-25
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLUTION
SERIAL NO.
FROM
REF PART NO.
PRV NO. QTY
DESCRIPTION
CLAMP, 1/4 ID HOSE
NOTES:
1
86233090
86233150
86281060
86197640
86270780
86273930
86006520
86295050
86295060
86297210
86297850
86297890
86299330
862811000
86300310
86301050
86310710
86256090
86298090
86001530
86297230
86297440
86012550
86004570
86010820
86197400
86240610
86197750
20016
9
2
4
2
1
2
15
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
2
3
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
20042
39265
40064
57008
70051
70052
CLAMP, 3/8 HOSE (D-SLOT)
HOSE, 1/4 ID NYLOBRD X 8”
HOSEBARB, 1/8” FPT X 1/4”
NUT, 8-32 HEX
SCR, 8-32 X 1/2 PPHMS
SCR, 8-32 X 3/8 PPHMS SS
PLATE, BOTTOM
-
-
-
-
-
-
COVER, SIDE
COVER, NOZZLE MOUNT
CLAMP, SOLENOID PUMP
TERMINAL STRIP, 3-POS, .25
HARNESS, HANDLE CONNECTOR
HOSE, 1/2ID WIRE BOUND X 7”
BUSHING, STRAIN RELIEF
HOSE, 1/4 ID NYLOBRD X 27”
SCR, 8-32 X 1/2” PFHMS PLT
STRAINER, 1/2 NPT 80 MESH
ASSY, NOZZLE MOUNT
HOSEBARB, 1/2MPT X 1/2 HOSE 90
BAFFLE, ACOUSTIC
39274
-
-
-
730262
-
40039
-
-
-
JET, PROMAX, 11008
JET, PROMAX, 11001
44067
87192
31022
44104
78161
JET BODY, MINI PROMAX BODY
WASHER, 7/16 X 3/4 X .19 RUBBER
ELBOW, 1/8NPT STREET
HOSEBARB, 1/8 MPT X 1/4H 90D
TEE, 1/8 NPT STREET RUN
VALVE, SOLENOID, 120VAC, 1/8
NPT
29
86297290
-
1
30
31
32
33
34
35
36
37
38
39
86197520
OPEN
40011
1
-
HOSEBARB, 1/8MPT X 1/4 DL
-
PUMP, 110/120 60 HZ FLOJET
FOAM, 1 X 1 X 18
-
250-78
-
86201110
86302620
86302640
86010640
86245040
86010650
86006800
86310230
1
1
1
3
1
1
1
1
-
FOAM, SOLN ASM LID
87016
50279
87018
70361
-
WASHER, #10 LOCK EXT STAR SS
LABEL, GROUND SYMBOL
WASHER #10 X 9/16 OD
SCR, 10-32 X 1/2 PHTR PLT
COVER, SOLN ASM, LOWER, TRIM
86302100 CLIPPER DUO 10/17/08
5-26
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLUTION TANK
86302100 CLIPPER DUO 10/02/07
5-27
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLUTION TANK
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
NOTES:
1
2
3
4
5
6
7
8
86200820 270-11A
1
1
1
1
1
1
1
1
1
4
1
3
1
1
1
4
1
1
1
1
1
1
1
1
1
1
NIPPLE, 1/8FPT QD ,MALE BRASS
HOSE ASM, FCT ADPTR X 60” NBRD
CLAMP, 1.0” WORM GEAR
CLAMP, 3/8 HOSE (D-SLOT)
COVER, CLP SOLUTION
86260690
86233110
86233150
86234790
86238460
86197520
86197920
86301930
86006860
86276160
86276290
86276490
86277050
86240790
86010650
86010670
86297620
86297990
86299390
86299530
86299590
86301780
86270920
86273950
86246080
02130
20018
20042
27827
36259
40011
40023
-
70403
70604
70626
70670
70782
82358
87018
87029
-
HOOK, STRAP
HOSEBARB, 1/8MPT X 1/4 DL
HOSEBARB, 1/2MPT X 3/8 NYL DL
SHROUD, FRONT
SCR, #10 X 1/2 PPHST TYPE B SS
SCR, 10-32 X 5/8 PPHMS BLK
SCR, #10 X 3/4 PPHST HI-LO BLK
SCR, 5/16-18 X 5/8 HHCS SS
SCR, 5/16-18 X 3/4 SHCS SS
HOSEBARB, 1/2MPT X 3/4 90D
WASHER, #10 X 9/16 OD
WASHER, 5/16 FLAT SS
STRAP, HAND TOOL
BRKT, HANDTOOL HOSE
BAFFLE, FILL PORT
BRKT, BOTTLE & QD MOUNT
HOSE, 3/4ID X .12W CLR X 25”
TANK, SOLUITON, TRIMMED
NUT, 6-32 HEX NYLOCK SS
SCR, 6-32 X 1/2 PPHMS
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
-
-
-
-
-
57049
70056
51368
LANYARD, 18.0 W/LOOP & EYE
86302100 CLIPPER DUO 10/02/07
5-28
Download from Www.Somanuals.com. All Manuals Search And Download.
VAC SHOE
86302100 CLIPPER DUO 10/02/07
5-29
Download from Www.Somanuals.com. All Manuals Search And Download.
VAC SHOE
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
VACUUM SHOE, 18"
GASKET, 18” VAC SHOE OUTER
GASKET, 18 “ VAC SHOE SIDE
GASKET, 18” VAC SHOE CENTER
PLATE, 18” VACUUM SHOE
SCR, M5X12, SHCS, ISO4762, SS
WIPER ASM 18”
NOTES:
1
2
3
4
5
6
7
8
9
86225650
86218110
86218270
86218260
86223230
86172950
86293170
86293190
86293180
85087
35363
35380
35379
85089
70909
-
1
1
2
1
1
12
1
2
-
-
PIN, CLEVIS
BEARING, BRONZE FLANGED
1
86302100 CLIPPER DUO 10/02/07
5-30
Download from Www.Somanuals.com. All Manuals Search And Download.
VAC SHOE MOUNTING
86302100 CLIPPER DUO 10/02/07
5-31
Download from Www.Somanuals.com. All Manuals Search And Download.
VAC SHOE MOUNTING
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
86003010
86004290
86002390
86297470
86276490
86010670
86295030
86278280
86296510
86005810
86259420
86272750
86010730
86298080
86259410
86010630
86273750
86293160
27759
39491
20063
-
70670
87029
-
1
1
1
1
2
2
2
2
1
2
2
1
1
2
2
2
2
2
CUFF. HOSE 1.5” BLK A 2161
HOSE, 1.5 BLK VAC X 45”
CLAMP, 1.75” WORM GEAR X .312
ASM, TRAVEL LIMITER
SCR, 5/16-18 X 5/8 HHCS SS
WASHER, 5/16 FLAT SS
SPRING, EXT .562D X 6.0L X .072W
SHOULDER BOLT
70350
-
BRKT ASM, VAC SHOE MOUNT
NUT, 1/4-20 HEX NYLOCK SS
WASHER, THRUST .51 ID X 1 ODBRO
RING, 5/8 EXTERNAL SNAP
WASHER, 5/8
57245
87232
67010
87088
-
87206
87013
70011
-
SCR, 5/16-18 X 3/4 FHSC SS
WASHER, THRUST .51 ID X 1 OD X .063
WASHER, 1/4 ID X 5/8 OD SS
SCR, 1/4-20 X 5/8 HHCS SS
VAC SHOE ASM 18”
86302100 CLIPPER DUO 06/06/08
5-32
Download from Www.Somanuals.com. All Manuals Search And Download.
VACUUM
1
2
3
6
4
5
86302100 CLIPPER DUO 10/17/07
5-33
Download from Www.Somanuals.com. All Manuals Search And Download.
VACUUM
SERIAL NO.
FROM
REF
PART NO. PRV NO.
QTY
DESCRIPTION
NOTES:
1
2
3
86300300
86217480
86299250
-
4
1
1
SCR, #8 X 2” PPHSMS
COVER, VAC MOTOR
ASSY, VAC MOTOR
CLAMP, 1.75” WORM GEAR X
.312
270805
-
4
86002390
20063
1
5
6
86004290
86302620
39491
-
1
1
HOSE, 1.5 BLK VAC X 45”
FOAM, 1 X 1 X 18
86302100 CLIPPER DUO 10/17/08
5-34
Download from Www.Somanuals.com. All Manuals Search And Download.
WHEEL & AXLE
3
4
2
1
5
6
7
2
1
86302100 CLIPPER DUO 10/02/07
5-35
Download from Www.Somanuals.com. All Manuals Search And Download.
WHEEL & AXLE
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
NOTES:
1
2
3
4
5
6
7
86276490
86010670
86219480
86001660
86226050
86010730
86294920
70670
87029
41567
41236
89279
87088
-
5
5
2
2
2
2
1
SCR, 5/16-18 X 5/8 HHCS SS
WASHER, 5/16 FLAT SS
HUBCAP, 9.75” WHEEL
HUBCAP, 5/8” SHAFT
WHEEL, 9.75” X 1.5”
WASHER, 5/8 ID X 1.18 X .06 SS
AXLE ASM, CLIPPER DUO
86302100 CLIPPER DUO 10/17/08
5-36
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING DIAGRAM
HANDLE CONSOLE
BLU
BLU
BLU
BLK
HANDLE SWITCH #2
HANDLE SWITCH #1
HANDLE SWITCH #3
BLK
BLK
BLU
4
ORG
6
3
VAC MOTOR
CIRCUIT BRKR
9
9
8
RELAY
BLU
SWITCH
90 F/I
SWITCH
SWITCH
1
5
9
90 F/I
90 F/I
ALL ON
BRN
DEEP CLEAN
PIGGYBACK
BLU
BLK
90 F/I
CONTINUOUS
90 F/I
90 F/I
90 F/I
RED
WHT
PIGGYBACK
90 F/I
WHT
13
14
PIGGYBACK
PIGGYBACK
BRUSH MOTOR
CIRCUIT BRKR
ORG
90 F/I
TRANSFORMER
ACCESSORY
90 F/I
90 F/I
LIGHT CLEAN
BUTTON
SPRAY
RED
WHT
PIGGYBACK
BLK
BRN
BLU
BLU
8
RED
7
RED
ATTACH TO CTRL BRKT
5
CTRL PNL GRD LUG
4
1
SOLUTION GROUP
2
10
TERMINAL STRIP
TERMINAL STRIP
11
RED
SOL
VALVE
SOL
PUMP
PUMP
13
WHT
BLK
WHT
GRN
VAC MOTOR
ASSY
JACKETED CABLE
12
14
START CAPACITOR
(150 ? F)
RUN CAPACITOR
(25 ? F)
WHT
RED
BLU
BLK
BRUSH DRIVE MOTOR
86302100 CLIPPER DUO 10/17/08
5-37
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING DIAGRAM
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
HARNESS, HANDLE
NOTES:
1
2
86296060
86297750
86298180
86296010
86296020
86295980
86268210
86295990
86296000
86299330
86299370
86299340
86299360
86294220
-
-
1
1
1
2
1
1
1
2
2
1
1
1
1
1
CORD ASM, 14/3 X 22 PGTL
3
-
WIRE, 540MM BLU/18 76046XSTRIP
WIRE, 240MM ORG/18 76031X76046
WIRE, 150MM RED/18 76031X76046
WIRE, 605MM BRN/18 76046X76047L
WIRE, 15” GRN/18 76008 X 76008
WIRE, 80MM BLU/18 76031X76046
WIRE, 150MM WHT/18 76046X6046
HARNESS, HANDLE CONNECTOR
WIRE, 10”WHT/14 76029 X 76029
HARNESS, BRUSH DECK
4
-
5
-
6
-
7
88205
8
9
-
-
-
-
-
-
-
10
11
12
13
14
WIRE, 10” RED/14 76029 X 76029
BRUSH DECK WIRING HARNESS
5-38
86302100 CLIPPER DUO 10/17/07
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED SPARE PARTS
SERIAL NO.
FROM
PART NO.
PRV NO.
DESCRIPTION
NOTES:
86215250
86216050
86295520
86002010
86001980
86215670
86218290
86007130
86007200
11049
12530
-
14942
14700
140839
35382
72128
72162
BELT, 2S 5MM HTD, 15W, 128T
BRUSH, EXTRACTOR 16”
BRUSH, EXTRACTOR 16” NATURAL
BOOT, 3/8 CIRCUIT BREAKER
BREAKER, 15A 250VAC 50VDC
BREAKER, 8A VDE CIRCUIT
GASKET, CONSOLE, HANDLE
SWITCH, DPDT 2-POSITION ROCKER
SWITCH, DPDT3-POSITION ROCKER
SWITCH, SPST 2- POSITION
ROCKER
86007140
72130
86218180
86003630
86299250
86298070
86297440
86012550
86201110
86234790
86256090
86004570
86293170
35370
34351
GASKET, DOME
FLOAT SHUT-OFF
ASSY, VAC MOTOR
ASSY, PUMP 110V
JET, PROMAX, 11008
JET, PROMAX, 11001
PUMP, 110/120 60 HZ FLOJET
COVER, CLP SOLUTION
STRAINER, 1/2 FPT 80 MESH
JET BODY, MINI PROMAX BODY
WIPER ASM 18”
-
-
-
-
250-78
27827
730262
44067
-
ALSO ORDER 76064L
(QTY 1) &
86298890 (QTY 1)
TERMINALS
86297870
-
ASM, INTERIM SWITCH
5-39
86302100 CLIPPER DUO 10/17/08
Download from Www.Somanuals.com. All Manuals Search And Download.
SERIAL NUMBERS
REF.
NO.
1
MODEL: SERIAL #
10080480: 10080480000338
86302100 CLIPPER DUO 10/17/07
5-40
Download from Www.Somanuals.com. All Manuals Search And Download.
|