PORTABLE EXTRACTOR-240V
Operating Instructions
MODELS: 621-222MO
10070460
621-225MO
10070470
Read these instructions before using the machine
V
86038610 04/21/08
PRV NO. 98838
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Machine Data Log/Overview.........................2
Table of Contents..........................................3
GROUP PARTS LIST
Frame Group (200 psi) .............................................5-1
Frame Group (500 psi) .............................................5-3
Pump Group (200 psi) ..............................................5-5
Pump Group (500 psi) ..............................................5-7
Recovery and Solution Tank Group .......................5-9
Vacuum Motor Group...............................................5-11
Wiring Group (200 psi)..............................................5-13
Wiring Group (500 psi)..............................................5-14
EC Declaration...........................................................5-15
HOW TO USE THIS MANUAL
How to use this Manual.................................1-1
SAFETY
Important Safety Instructions ........................2-1
Hazard Intensity Level. .................................2-2
Safety Label Location. ..................................2-3
Grounding Instructions..................................2-4
OPERATIONS
Technical Specifications. ..............................3-1
Controls.........................................................3-2
Machine Operation........................................3-3
Pre-Run Machine Inspection......................3-3
Equipment Set-up ......................................3-3
Priming the Pump ......................................3-3
Emptying & Cleaning Tanks.......................3-3
MAINTENANCE
Daily Maintenance ........................................4-1
Periodic Maintenance ...................................4-1
Monthly Maintenance....................................4-1
Semi-annually ...............................................4-1
Lubrication ....................................................4-1
Storage .........................................................4-1
Vacuum Motor Replacement ........................4-2
Solution Pump Replacement ........................4-2
Pump Replacement Kits ...............................4-3
Pressure Regulator.......................................4-4
Machine Troubleshooting..............................4-5
3
NINJA INTL 86038610 03/29/07
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THIS MANUAL
The SAFETY section contains important information
regarding hazard or unsafe practices of the
machine. Levels of hazards are identified that could
result in product or personal injury, or severe injury
resulting in death.
This manual contains the following sections:
-
-
-
HOW TO USE THIS MANUAL
SAFETY
OPERATIONS
-
-
MAINTENANCE
PARTS LIST
The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.
The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.
The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition. They are
listed in this general order:
Parts may be ordered from authorized dealers.
When placing an order for parts, the machine model
and machine serial number are important. Refer to
the MACHINE DATA box which is filled out during
the installation of your machine. The MACHINE
DATA box is located to the inside of the front cover
of this manual.
-
-
-
-
-
Maintenance
Lubrication
Vacuum Motor Replacement
Solution Pump Replacement
Troubleshooting
MODEL _____________________________________
DATE OF PURCHASE ________________________
SERIAL NUMBER ____________________________
SALES REPRESENTATIVE # ___________________
DEALER NAME ______________________________
OPERATIONS GUIDE NUMBER __________________
The PARTS LIST section contains assembled parts
illustrations and corresponding parts list. The parts
lists include a number of columns of information:
-
-
REF – column refers to the reference
number on the parts illustration.
PART NO. – column lists the part
number for the part.
PUBLISHED ________________________________
-
-
PRV NO. – reference number.
QTY – column lists the quantity of the
part used in that area of the machine.
DESCRIPTION – column is a brief
description of the part.
The model and serial number of your machine is on
the front of the Frame.
-
-
SERIAL NO. FROM – column indicates
the first machine the part number is
applicable to. When the machine design
has changed, this column will indicate
serial number of applicable machine.
The main illustration shows the most
current design of the machine. The
boxed illustrations show older designs.
NOTES – column for information not
noted by the other columns.
-
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.
NOTE: The number on the lower left corner of the
front cover is the part number for this manual.
SERIAL # TAG
NINJA INTL 86038610 03/29/07
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
This machine is for commercial use.
To reduce the risk of fire, electric shock, or injury:
WARNING:
Connect to a properly grounded outlet. See Grounding Instructions.
Do not leave the machine unattended. Unplug machine from outlet when not in use and before
maintenance or service.
Use only indoors. Do not use outdoors or expose to rain.
Do not allow machine to be used as a toy. Close attention is necessary when used by or near
children.
Use only as described in this manual. Use only manufacturer’s recommended components and
attachments.
Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding
the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or
dropped into water, return it to an authorized service center.
Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord
around sharp edges or corners.
Do not run machine over cord. Keep cord away from heated surfaces.
Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.
Do not handle the electrical plug or machine with wet hands.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce
airflow.
This machine is intended for cleaning carpet only.
Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
This machine is not suitable for picking up health endangering dust.
Turn off all controls before unplugging.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this
machine near flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals,
factories, shops and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
If foam or liquid comes out of machine, switch off immediately.
SAVE THESE INSTRUCTIONS
NINJA INTL 86038610 03/29/07
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
HAZARD INTENSITY LEVEL
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR
SAFETY. The level of hazard intensity is determined by the following definitions:
! WARNING
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
! CAUTION
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property
damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper
operating condition. Following is information that signals some potentially dangerous conditions to the
operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate
all safety devices on the machine. Please take the necessary steps to train the machine operating
personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the
machine.
.
2-2
NINJA INTL 86038610 03/29/07
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY LABEL LOCATION
NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become
illegible, promptly replace them.
LABEL WARNING
86242230
PRV NO. 500009
LABEL CIRCUIT INTERRUPTER
86200570
PRV NO. 170-41
NINJA INTL 86038610 03/29/07
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
GROUNDING INSTRUCTIONS
THIS PRODUCT IS FOR COMMERCIAL USE
ONLY.
ELECTRICAL:
The amp, hertz, and voltage are listed on the
data label found on each machine. Using
voltages above or below those indicated on the
data label will cause serious damage to the
motors.
EXTENSION CORDS:
If an extension cord is used, the wire size must
be at least one size larger than the power cord
on the machine, and must be limited to 50 feet
(15.5m) in length.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should
malfunction or break down, grounding provides
a path of least resistance for electric current to
reduce the risk of electric shock. This
appliance is equipped with a cord having an
equipment-grounding conductor and grounding
plug. The plug must be inserted into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes
and ordinances.
Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or service person if you are in
doubt as to whether the outlet is properly
grounded. Do not modify the plug provided
with the appliance - if it will not fit the outlet,
have a proper outlet installed by a qualified
electrician.
NINJA INTL 86038610 03/29/07
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE LEFT BLANK INTENTIONALLY
NINJA INTL 86038610 03/29/07
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
ITEM
MEASURE
ELECTRICAL
230 Volt, 50 hz
Vacuum Motor
Solution Pump
Dual 2 stage
200 psi
500 psi
Solution Capacity
Recovery Capacity
Weight- Empty
Weight-Full Solution
Height
Length
Width
Power cord
10 gal (38 L)
8 gal (240 kg)
110 lbs (240 kg)
200 lbs (440 kg)
36 inches (91.44 cm)
29 inches (73.66 cm)
19.5 inches (49.53 cm)
22 feet (6.71 m)
LENGTH
WIDTH
HEIGHT
BY
CENTURY 400
PUMP
VACUUM #1
VACUUM #2
NINJA INTL 86038610 03/29/07
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
BY
CENTURY 400
1
2
3
1.
2.
3.
Pump Switch
Vacuum #1 Switch
Vacuum #2 Switch
NINJA INTL 86038610 03/29/07
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE OPERATION
EMPTYING AND CLEANING
Always use
PRE-RUN INSPECTION
1. Check all fittings and connectors for proper
assembly.
defoamer if foaming
occurs. Foam will
suspend large particles that may damage
vacuum(s) as well as allow liquid into the
vacuum motor(s) without activating the float
shutoff.
2. Check all hoses for leaks. Repair or replace
any damaged hoses.
3. Check power cord(s) for any damage. If
damaged, replace.
1. Before proceeding, make certain that the
nozzle is functioning properly.
EQUIPMENT SET-UP
a. To check, hold the wand about one foot
above the surface to be cleaned and
open the wand valve. A full spray should
be observed from the nozzle.
1. Plug power cord from machine into properly
grounded wall outlet.
2. Turn vacuum motor switch on and off to
make sure there is electrical power at
machine.
b. If the nozzle is not showing a full spray
pattern, adjust nozzle for proper pattern,
clean, or replace nozzle.
3. Connect vac hose to machine. Slide the
swivel cuff over the outlet on the tank.
2. Normally, chemical is applied on the push
stroke of the wand when cleaning.
4. Connect the hose to your machine and
wand. Pull back the knurled collar on the
quick disconnect coupler and push onto the
connection on the chassis. To avoid leaks,
check to be that a positive connection was
made.
Vacuuming is done on the pull stroke. For
heavily soiled carpets the wand may be used
in a scrubbing manner, applying chemical in
both the push and pull stroke.
3. When cleaning, keep the working opening
(wand mouth) flat on the surface being
cleaned. Keep the wand moving when the
valve is open.
5. Using a clean container, fill the solution tank
with clean hot water. Mix in a non-foaming
cleaning concentrate for use in hot water
extraction machines, following the
manufacture’s instructions printed on
container.
NOTE: When using a powder cleaner, pre-mix
with hot water in a clean container before adding
to the solution tank.
4. The shutoff float inside the vacuum tank will
impede the vacuum flow when the vacuum
tank is full.
When this occurs, empty the vacuum tank by
opening the dump valve and dispose of the
waste in a proper manner.
6. Turn pump and vacuum switch(s) to the on
position.
5. Once the vacuum tank has been emptied,
you may once again proceed with cleaning
7. Start cleaning.
PRIMING THE PUMP (SELF PRIMING VALVE)
[High Pressure Pump Models ONLY]
Turn pump and both vacuums on.
1. Press lever (located above the accessory
connection; front of machine) toward
machine.
2. Do this for 30 seconds or until there is a
steady flow of water flowing through the sight
tube. (located on right side of recovery tank.)
NINJA INTL 86038610 03/29/07
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
DAILY MAINTENANCE
2. Check hoses for wear, blockages, or damage.
Frayed or cracked hoses should be repaired or
replaced to eliminate vacuum or solution
pressure.
Unplug power cord(s)
before servicing or
making any repairs.
3. Check all handles, switches, knobs, electrical
cables and connections on your machine for
damage. If the cable insulation is broken or
frayed, repair or replace it immediately. Don’t
take chances with electrical fire or shock.
1. Flush the entire system, including floor tool,
hand tool, etc., with 1 to 3 gallons of clean, hot
water.
2. Vacuum out the solution tank.
3. Rinse tank with fresh water. Periodically
inspect the recovery tank and decontaminate if
necessary, using a Hospital Grade Virucide or
a 1-10 bleach to water solution. Wastewater
should be disposed of properly.
4. Clean out solution tank. Remove and clean
solution screen.
5. Clean outside of all tanks and check for
damage.
MONTHLY MAINTENANCE
4. Occasionally check filter screen at the bottom
of the solution tank and rinse clean with hot
water if necessary.
1. Check all bearings for noise and wear.
2. Check all gaskets for wear and leakage.
3. Check pump pressure; observe spray pattern
and check gauge if necessary.
5. Inspect hoses for wear. Frayed or cracked
hoses should be replaced to avoid vacuum or
solution pressure loss.
4. Check overall performance of machine.
SEMI-ANNUALLY
6. Inspect power cord for wear or damage. This
cable will lie on wet carpet. To prevent
1. Check vacuum motor brushes.
electrical shock replace cords that are frayed
or have cracked insulation immediately.
LUBRICATION
7. Clean all dirt and obstructions from drain valve
and gaskets to prevent possible leakage and
premature wear.
For pressure regulator and pump cam lubrication,
use a light silicone lubricant which will not damage
o-rings. A small tube (86246790 – PRV NO.
51391) is supplied with your machine.
8. Run clean water through solution pump when
work is complete.
STORAGE
9. Empty both tanks and rinse, run vacuum (s) for
at least one minute to dry motor(s).
Thoroughly clean machine if it is to be stored. You
must protect this machine from freezing while in
storage.
10. Store with access covers removed to allow
tanks to dry.
By using the Self Priming Lever you may help clear
out all water lines.
DO NOT attempt to
repair hose!
Repairing high-
pressure hoses may result in severe burns and
serious injury.
Make sure both recovery and solution tanks are
empty. Turn on both vacuum switches and press
lever. All water should be removed and sprayed
into the recovery tank.
PERIODIC MAINTENANCE
Empty the remaining water and wipe dry.
1. Twice a month, flush a white vinegar solution
(One quart vinegar to two gallons of water) or
anti-browning solution (mixed as directed)
through the extractor, turning pump switch
on/off several times, flush with clean water.
This will prevent build-up of alkaline residue in
the system.
HEAT MODELS ONLY: Be sure to thoroughly
drain water out of heater lines prior to storage in
colder climates. This heater will freeze and
possibly crack voiding your warranty.
NINJA INTL 86038610 03/29/07
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Only qualified
maintenance personnel
are to perform the
Vacuum Motor Carbon Brushes Replacement (Ametek)
End Cap
following repairs.
WARNING: The green
Carbon
ground wire must be
Brushes
VACUUM MOTOR REPLACEMENT
attached for safe operation.
See wiring diagram.
1. Turn off all switches and unplug machine.
2. Remove recovery tank.
3. Locate the vacuum motor wires and disconnect
at the connector.
Note: When replacing carbon brushes loosen wire terminal
BEFORE removing screws on bracket.
4. Remove the vacuum motor.
5. Reverse process to install vacuum motor.
Wire
Terminal
SOLUTION PUMP REPLACEMENT
1. Turn off all switches and unplug the machine.
2. Remove recovery tank.
3. Remove solution hoses from fittings in pump.
Note:
Place
stop in
groove.
4. Remove the screws that fasten the pump to the
frame.
5. Reverse process to install pump.
Vacuum Motor Carbon Brushes Replacement (Windsor)
End Cap
If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
WARNING: The green
Carbon
qualified service center.
Wire Terminal
ground wire must be
Brushes
attached for safe operation.
See wiring diagram.
Important:
These brushes wear quicker as the length shortens due to
increased heat. Spring inside brush housing will damage
motor if brushes are allowed to wear away completely.
If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.
3/8 (9.5mm)
Important:
These brushes wear quicker as the length shortens due to
increased heat. Spring inside brush housing will damage
motor if brushes are allowed to wear away completely.
Periodically check the length of the carbon brushes. Replace
both carbon brushes when either is less than 3/8" (9.5mm)
long.
3
[9.5mm]
8
Periodically check the length of the carbon brushes. Replace
both carbon brushes when either is less than 3/8" (9.5mm)
long.
NINJA INTL 86038610 03/29/07
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
PUMP REPLACEMENT KITS
200 PSI
CAM & BEARING KIT
862011470
PRV NO. 250-79G
VALVE & O-RINGS KIT
86201160
PRV NO. 250-79F
PLUNGER & SEALS KIT
86201150
PRV NO. 250-79E
PUMP REPLACEMENT KITS
500 PSI
CAM & BEARING KIT
86201040
PRV NO. 250-73C
VALVE & O-RINGS KIT
(BOTH SIDES)
86201030
PRV NO. 250-73B
PLUNGER & SEALS KIT
86201080
PRV NO. 250-75A
NINJA INTL 86038610 03/29/07
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
PRESSURE REGULATOR
For best results with the pressure regulator, we recommend that you clean and lubricate
the piston and u-cup with Superlube lubricant monthly or when pressure drop seems excessive.
1. Turn unit off before lubricating.
2. Remove cap, spring and spring retainer plate.
3. With fingertips remove piston and u-cup.
4. Wipe piston and u-cup clean of any film or scale.
5. Lubricate the piston and u-cup with Superlube.
6. Reassemble regulator.
7. With pump ON, re-adjust pressure regulator for normal operation.
LUBRICATE U-CUP WITH SUPERLUBE MONTHLY.
U-CUP
SPRING RETAINER PLATE
OUT
PISTON
SPRING
CAP
NINJA INTL 86038610 03/29/07
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
PROBLEM
Loss of Power
CAUSE
SOLUTION
Dead electrical circuit
Faulty power cord
Check building circuit breaker or fuse box.
Replace
Equipment not grounding
Receptacle not grounded
Follow grounding instructions exactly
Contact an electrician to check building’s wiring
Have a trained service technician check machine’s
wiring
Electrical shock
Internal wiring problem
Worn motor brushes
Motor worn out
Faulty switch
Replace
Replace
Replace
Vac motor speed varies
or doesn’t run
Loose vacuum dome
Center and seal dome over tank
Crack in dome of poor joint Replace or repair using acrylic plastic cement only
Lint or dirt clogging
With power off clean screen
vacuum screen
Loose cuffs on vacuum
Tighten cuffs turning counterclockwise
hose
Loss of vacuum
Vac motor seals leaking
Floor tool vac chamber
clogged
Replace
Wash out with hose. Pick lint out with a wire
Vac motor, hose, or dome
gasket
Replace
Pump inlet screens
plugged
Clean inlet screens
Press trigger to open valve on cleaning wand to
relieve air
Pump air locked
Pump runs no solution
Internal or external
solution line damaged and Replace
leaking
Jet orifice on cleaning
wand is to large
Internal pump components
wearing out
Total jet opening for 100 psi should be .06 to .08
Replace, see pump kit components (pg 4-3)
Pump runs, loss of
pressure
Note: Operation of pump using a wand or hand tool with an orifice of less than .06
will cause pump to cavitate or pulsate and could result in premature wear of pump
components.
Check valves in pump
Take piston from BPR and lubricate with Superlube.
head for particles or cuts in
If problem still exists change BPR kit
seals
Unit not plugged in
Loose wiring
Connect unit to 3 prong grounded outlet
See dealer
Pump will not run
Solution hose fitting hard
to connect
Clean with steel wool. Soak in acetic acid (white
vinegar). Lubricate lightly with silicone base lubricant.
Make several passes at right angles to each other.
Use a pre-spray.
Adjust solution pressure to lower settings. Make
several passes without spray
Corrosion on fittings.
Severe soil conditions
Over saturation
Carpet not getting clean
Carpet too wet
Leaving carpet too wet
Too much chemical
Light carpet with no brown
prevention
Check for loss of vac pressure
Check label for correct solution concentration
Carpet browning
Go over carpet with browning prevent only
Solution hose connection
Faulty pump
Faulty floor tool valve
Faulty pump switch
Check for positive connection
Repair or replace
Repair or replace
Repair
Solution not flowing
properly
4-5
NINJA INTL 86038610 03/29/07
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME GROUP (200 PSI)
2
3
1
4
26
5
27
6
7
8
7
25
24
23
22
4
21
9
10
19
11
6
28
4
15
16
20
18
12
17
13
14
11
NINJA INTL 86038610 03/29/07
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME GROUP (200 PSI)
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
3
4
5
6
7
8
86274040
86006700
86200010
86279190
86005640
86201300
86198460
86202230
86199590
86005810
86201290
86002450
86199430
86273830
86200670
86091030
86201640
86271380
86202250
86273810
86199200
86064930
86005670
86256200
86199550
86202160
70076
70232
140-01
87095
57030
280-03
20008
390-09A
140-04
57245
280-02
22015
040-03
70020
500359
62900
330-13
57196
040-06
70018
010-04B
08055
57040
73200
060-04B
320-05
4
4
1
10
4
4
2
1
2
2
9
1
2
8
1
1
3
2
2
1
1
1
1
1
1
1
1
1
SCR, 10-32 X 1.0 PFHMS SS
SCR, 10-32 X 3/8 FHMS SS
HINGE SET CHROME
WASHER, #10 FLAT PLTD
NUT, 10-32 HEX NYLOCK
RIVET ALUMINUM 3/16 X 3/4
CLAMP, 5/8 NYLON UL/USA
WASHER 9/16 S/S USS-THICK
DRAW PULL LATCH LOCKING
NUT, 1/4-20 HEX NYLOCK SS
RIVET AL. 3/16 X 1/2 CLOSED
COUPLER, 1/4 QD
CASTER SWIVEL 4” SWIVEL
SCR, 1/4-20 X 1/2 HHCS SS NP
LABEL, NINJA 3 SWITCH NO HEAT
PLATE, NINJA 3 SWITCH NO HEAT
ROCKER SWITCH DBL POLE
NUT, 1/2 PUSH-ON DOME CAP
WHEEL 8” BLK CENTERED HUB
SCR, 1/4-20 X 1 HHCS SS
AXLE SINGLE NINJA
BASE, NJA DLX 200 2 ST N/H
NUT, 1/2 NPT CONDUIT
STRAIN RELIEF 1/2 NPT FLEX
CORDSET 1.00M3X25 SAA/3, OR-1A
VELCRO STRAP
FILTER, INLINE 16A F55047/1
NUT, M8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
86161480 33-901006
86136280 57054
NINJA INTL 86038610 03/29/07
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME GROUP (500 PSI)
2
3
4
5
1
33
7
12B
6
29
32
9
4
10
11
31
28
30
27
25
12A
12B
16
13
24
34
16
4
17
18
23
14
22
19
12A
15
16
21
20
NINJA INTL 86038610 03/29/07
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME GROUP (500 PSI)
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
3
4
5
6
7
8
9
86006540
86006700
86200010
86279190
86005640
86202230
86197390
-
70068
70232
140-01
87095
57030
390-09A
31021
OPEN
57104
140-04
57245
280-02
280-03
190-07
22015
18036
70020
330-13
62900
500359
70626
070-08A
070-08B
57196
89252
010-07
57040
73200
060-04B
170-41
-
4
4
1
10
4
1
1
-
SCR, 10-32 X 3/4 PFHMS SS
SCR, 10-32 X 3/8 FHMS SS
HINGE SET CHROME
WASHER, #10 FLAT PLTD
NUT, 10-32 HEX NYLOCK
WASHER 9/16 S/S USS-THICK
ELBOW, 1/4 NPT X 45D STREET
-
NUT, 10-32 W/STAR WASHER PLTD
DRAW PULL LATCH LOCKING
NUT, 1/4-20 HEX NYLOCK SS
RIVET AL. 3/16 X 1/2 CLOSED
RIVET ALUMINUM 3/16 X 3/4
PRESSURE GAUGE 1000 PSI
COUPLER, 1/4 QD
86005700
86199590
86005810
2
2
2
11
4
1
1
2
8
3
1
1
4
1
1
2
2
2
1
1
1
1
1
1
2
1
1
10
11
12A 86201290
12B 86201300
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
86200970
86002450
86232600
86273830
86201640
86091030
86200670
86276290
86199660
86199670
86271380
86202280
86090740
86005670
86256200
86199550
86200570
86310610
86199320
86199460
CASTER, 5” DIA SWIVEL
SCR, 1/4-20 X 1/2 HHCS SS NP
ROCKER SWITCH DBL POLE
PLATE, NINJA 3 SWITCH NO HEAT
LABEL, NINJA 3 SWITCH NO HEAT
SCR, #10 X 3/4 PPHST HI-LO BLK
FAN FINGER GUARD
FAN 105 CFM AXIAL 220V
NUT, 1/2 PUSH-ON DOME CAP
WHEEL, 12” BLK CNTRD HUB
AXLE ASM, NJA
NUT, 1/2 NPT CONDUIT
STRAIN RELIEF 1/2 NPT FLEX
CORDSET, 1.0MM3X25 SAA/3, OR-1A
LABEL CIRCUIT INTERUPTER
BASE, NINJA 500 240V
110-14A
20008
CAP PLUG 1”
CLAMP, 5/8 NYLON UL/USA
FILTER, INLINE 16A F55047/1
NUT, M8
86161480 33-901006
86136280 57054
NINJA INTL 86038610 04/21/08
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
PUMP GROUP (200 PSI)
1
2
1
1
9
3
6
4
14
15
5
7
2
9
8
1
16
13
10
11
12
1
3
17
18
19
5-5
NINJA INTL 86038610 03/29/07
Download from Www.Somanuals.com. All Manuals Search And Download.
PUMP GROUP (200 PSI)
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
86233150
86280750 151-38A
20042
5
2
2
1
1
1
1
1
2
2
4
2
1
1
1
1
1
1
1
CLAMP, 3/8 HOSE (D-SLOT)
HOSE, 1/2 WIREBOUND X 21”
HOSEBARB, 1/4 MPT X 1/2 DL
BPR PUMPTEC NINJA 200PSI
NIPPLE, 1/4 CLOSE
NIPPLE, ¼ X 1.5
PLUG, 1/4 BRASS PIPE
NIPPLE, 1/4 X 3
ELBOW, 1/4 FPT X 1/4 FPT
NUT, 1/4-20 HEX NYLOCK SS
WASHER, 1/4 ID X 5/8 OD SS
SCR, 1/4-20 X 1.25 HHCS SS
HOSE, PULSE 24.0 1/4 MPT X 1/4 MPT
PUMP/MOTOR, 200PSI 230V AC
HOSE, 3/8 WIREBOUND X 35”
HOSEBARB, 1/4MPT X 3/8 DL
VALVE, KNGSTN 3” LVR 500 PSI
NIPPLE, 1/4 X 1.5
86068520
86199230
86005590
86197670
86272730
86247710
86197370
86005810
86010630
86020350
40028
250-33
56014
56023
66017
56022
31017
57245
87013
70019
86200130 151-37C
86200940
86282310
86197550
86258970
86197670
86197760
65227
39699
40014
84193
56023
78308
TEE, 1/4 STREET
NINJA INTL 86038610 03/29/07
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
PUMP GROUP (500 PSI)
1
1
2
16/17
21
6
1
8
15
3
1
7
4
5
7
1
9
6
6
13
10AB
13
27
12
8
1
11
16
6
14
17
19
18
NINJA INTL 86038610 04/21/08
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
PUMP GROUP (500 PSI)
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
3
4
5
6
7
8
9
86233150
86280750 151-38A
86197540
86199270
86200170 151-42C
86197420
86200840
86197720
86201780
20042
7
1
2
1
1
3
2
3
1
1
CLAMP, 3/8 HOSE (D-SLOT)
HOSE, 1/2 WIREBOUND X 21”
HOSEBARB, 3/8 MPT X 1/2 DL
BPR 500 PSI
HOSE, PULSE 15.0 1/4 FBS X 3/8 MPT
ELBOW, 3/8 NPT STREET
NIPPLE, 3/8 X 1.5 BRASS
PLUG, 3/8 MPT
40013
250-36
31026
56005
66029
78029
65224
65221
57105
87013
70018
39581
39549
73999
TEE, 3/8
10A 86201250
10B 86288840
PT500PSI PUMP/MOTOR ONLY 220V
*
REF REPLACEMENT MOTOR KIT
PRIOR TO SN *
11
12
13
14
15
16
17
86005710
86010630
86273810
86200370
86281980
86008220
86007250
2
2
2
1
1
1
NUT, 1/4-20 HEX W/STAR WASHER
WASHER, 1/4 ID X 5/8 OD SS
SCR, 1/4-20 X 1 HHCS SS
HOSE, PULSE 20.0 1/4 MPT X 3/8 MPT
HOSE, 1/2” X 5”
SCREEN ASM
730000 REF REPLACEMENT SCREEN FOR 73999
NOT SHOWN
WITH BRASS &
HOSES
18
86201230
65222
REF PT500PSI COMPLETE ASM, 220V
19
20
22
23
24
25
26
27
86201240
86201260
86282310
86197550
86258970
86197670
86197760
86271370
65223
65225
39699
40014
84193
56023
78308
57189
REF PT MOTOR W/ CAM 220V
REF PT500PSI PUMP HEAD ONLY
NOT SHOWN
NOT SHOWN
1
1
1
1
1
2
HOSE, 3/8 WIREBOUND X 35”
HOSEBARB, 1/4MPT X 3/8 DL
VALVE, KNGSTN 3” LVR 500 PSI
NIPPLE, 1/4 X 1.5
TEE, 1/4 STREET
NUT, 1/4-20 FLANGE LOCK
NINJA INTL 86038610 04/21/08
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOVERY & SOLUTION TANK GROUP
1
4
36
3
35
33
32
7
34
5
10
2
8
6
9
31
10
11
30
29
19
20
28
27
22
12
13
21
22
23
23
14
36
24
25
26
18
17
15
16
16
NINJA INTL 86038610 03/29/07
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOVERY & SOLUTION TANK GROUP
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
3
4
5
6
7
8
86033370
86200290
86199840
86033240
86273820
86199900
86201290
86064760
86090850
86279610
86005810
86199970
86006670
51355
260-33
090-12A
090-17
70019
110-26A
280-02
31082
065-42
87190
57245
120-08
70201
1
1
1
1
6
1
2
1
1
12
6
1
4
1
1
5
1
1
6
1
2
2
2
2
2
1
1
1
1
2
3
3
1
5”
1
2
LID, NJA DLX LT GRY ALL
HOSEBARB, 1.5MPT X 1.5
FLOAT CAGE ASSY COMPLETE SLIP
NINJA STAND PIPE ASSY
SCR, 1/4-20 X 1.25 HHCS SS
GASKET NINJA LID
RIVIT AL. 3/16 X 1/2 CLOSED
ELBOW, 1.5FS X 1.5FPT PVC MCHD
FLOOD MACHINE BAFFLE
WASHER, SEAL 5/8 OD NEOPRENE
NUT, 1/4-20 HEX NYLOCK SS
MACHINE HANDLE BRASS/CHROME
SCR, 1/4-20 X 3/4 FHCS DL
DUMP VALVE, 2”
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
86161460 15-808123
86161470 11-800444
ELBOW, 2” 45D PVC SCH40
SCR, 10-32 X 3/8 PPHMS SS NP
CLAMP, 5/8 NYLON UL/USA
TANK, RECVRY NJA ALL
86007050
86198460
86033410
86237510
86197370
86010630
86090230
86197570
86273830
86090770
86199630
86247980
86192840
86033500
86200580
86010690
86201280
86200730
86198530
86090320
86237770
70683
20008
75330
35182
31017
87013
87015
40028
70020
065-37
030-13
56015
290-08
75346
500341
87068
280-01
065-03C
99809
87257
35256
GASKET, FRAME
ELBOW, 1/4 FPT X 1/4 FPT
WASHER, 1/4 ID X 5/8 OD SS
WASHER, 9/16 ID X 1.06 OD SS
HOSEBARB, 1/4 MPT X 1/2 DL
SCR, 1/4-20 X 1/2 HHCS SS NP
BRKT, RECOVERY BUCKET NINJA
ELBOW, 45 DEGREE 1/4 FPT
NIPPLE, 1/4 HEX
SOL SCREEN (ACORN) W/RUB BASE
TANK, SLTN NJA 200/500 PSI
LABEL, NINJA MAIN
WASHER, 1/8 RIVET BACKUP
RIVIT AL. 1/8 X 1/2
SOLUTION COVER NINJA DELUXE
FOAM TAPE, 1/8T X 3/4 1SDA
WASHER, HOSEBARB
GASKET, DUMP VALVE
NINJA INTL 86038610 03/29/07
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
VACUUM MOTOR GROUP
22
21
20
14
6
1
2
5
7
3
15
4
5
13
12
16
17
11
19
4
10
7
6
8
18
9
5-11
NINJA INTL 86038610 03/29/07
Download from Www.Somanuals.com. All Manuals Search And Download.
VACUUM MOTOR GROUP
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
3
4
5
6
7
8
9
86201510
86199910 110-26B
86090960 360-23A
390-26
3
1
1
2
6
6
2
3
1
-
SPACER NYLON 1/4ID X 1/2OD
GASKET, VAC BRACKET
PLATE, VAC
WAS 35168
86003760
86201970
86010630
86004020
86256490
86134400
86230760
86135330
86274460
86090950
86091230
86201280
86007010
86005810
86063170
86002380
86005710
86075210
86282300
86003500
86197370
35166
065-92
87013
360-06
70814
99656
140216
140688
70205
360-23
78463
280-01
70663
57245
39566
20046
57105
20062
39698
31076
31017
GASKET, VAC MTR
VAC SPACER 2 1/4 II STAGE
WASHER, 1/4ID X 5/8OD SS
VAC MOTOR, 230V 5.7 2ST TD
STUD, 1/4-20 X 4.5 SS
DUCT, 5/8 ID SPLIT FLEX
-
-
BRUSH SET, 230V VAC AMETEK
BRUSH SET, 230V VAC WINDSOR
SCR, ¼-20 X 3/8 HHCS PLT DL
PLATE ASM, REAR VAC
TUBE, VAC EXHAUST 2.5” LONG
RIVIT AL. 1/8 X 1/2
SCR, 1/4-20 X 3-1/4 HHCS PLT
NUT, 1/4-20 HEX NYLOCK SS
HOSE, VAC EXHAUST 2”ID X 2” LONG
CLAMP, 2.25” WORM GEAR
NUT, 1/4-20 HEX W/ STAR WASHER
CLAMP, 3/8 NYLON MCHND
HOSE, 3/8 CLR PLYURTHN X 24”
ELBOW, 1/4MPT X 3/8 TUBE, QC
ELBOW, ¼ FPT X ¼ FPT
SERVICE ONLY
SERVICE ONLY
-
*
10
11
12
13
14
15
16
17
18
19
20
21
22
1
1
1
2
3
3
1
2
3
1
1
1
1
NINJA INTL 86038610 03/29/07
5-12
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING GROUP (200 PSI)
NINJA INTL 86038610 03/29/07
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING GROUP (500 PSI)
NINJA INTL 86038610 03/29/07
5-14
Download from Www.Somanuals.com. All Manuals Search And Download.
|