VCP
SYSTEM
BY
Video Entertainment System
R6400V
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFE OPERATION
Before You Drive
What You Should Know About Having and Using the Auto Video
in Your Vehicle
Entertainment System
The Auto VideoEntertainment System is
designed for rear passengers only. The driver
cannot safely view the FPD (flat panel
display) while driving and should not attempt
to do so. Many states have laws that restrict
using a device in the vehicle that receives a
television broadcast.
The following guidelines will help you
operate your video entertainment system
safely and legally:
Never try to drive and view the screen.
Keep the back of the driver's seat forward of
the screen.
In most states it is unlawful for the FPD
screen to be visible to the driver, while other
states have yet to address this issue. The
screen can not be located at any point
forward of the back of the driver's seat in:
AL, AZ, CA, CO, LA, MA, MD, MN, NH,
NC, OR, PA, SC, WA and WI.
If you have a question, please call the Rosen
Tech Center at 1-888-883-2790.
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
DEPLOYMENT AND STOWING
Depending on your type of vehicle, and the
particular Auto Video™ System installed,
the Auto Video™ screen will deploy and
stow in one of the following ways:
PUSH BUTTON
PULL LATCH
The push button on the overhead console releases
the Auto Video™ screen just far enough so that it
can easily be position for optimal viewing. This
action sends power automatically to all the system
components. The screen will display the last video
signal chosen. (see 2-6 configuring your system)
Your system may have a pull latch located on the
bottom of the case. Pull latch down to deploy, the
Auto Video™ screen automatically sends power to
all the system components.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL CONTROLS
The buttons located on the side
of the screen perform many of
the same functions as the
system remote.
By depressing any of these buttons once, the OSM
displays the button’s function. Press again and the
function is carried out.
CHANNEL UP/DOWN
Scrolls up and down preset TV channels or
scrolls up and down TV channels (see
configuration settings).
VIDEO SOURCE
Selects video source
ꢀ
TVꢀVCPꢀAUX
SPEAKERS
Selects audio on or off to the speakers of the
vehicle sound system. Also, pressing and
holding this button for 5 seconds will turn
off the system.
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Status Indicator Light
The status indicator light is located on the right
side face of the viewing panel just under the word
"POWER". This indicator will display green when
the vehicle’s key is turned on. This indicates that
the system is ready for operation. The video
entertainment system includes a temperature
sensor. This sensor prevents the system from
operating when the temperature inside the vehicle
is too cold or too hot. The status LED will flash
green under this condition. This is a normal
feature of the system. As the interior of the vehicle
warms up or cools down the LED will return to a
constant green light and the system will be ready
for operation.
Status LED
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL AND OSM
2-2 System Remote Control
2-4 OSM (on-screen menus)
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM REMOTE
The system remote control is the heart of your
entertainment system. It controls the majority
of your system’s functions.
1
4
2
5
3
LCD
POWER
MUTE
SCAN
AUDIO
DISPLAY
6
9
MENU
LOCK
Video selection may be made by this remote control.
The TV Tuner is accessed by remote for channel
selection and for fine tuning.
7
8
ENTER
0
VCP
POWER
When your system is equipped with a Rosen video
cassette player, the VCP will operate using the same
system remote control.
AUTO
RECALL
TV/AV
TRACKING
All OSMs (On-Screen Menus) are controlled by the
system remote control.
The system remote control is infrared and therefore
must be aimed toward the flat panel display.
System Remote
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM REMOTE CONTROL
TV/AV This button selects the video source.
TV VCP AUX
LCD POWER This button sends power to the flat panel
display when pressed. It also turns off the
power to the entire system.
ꢀ
ꢀ
The OSM displays the video sources as:
TV # channel for television
AV1 for video cassette player
AV2 for the auxiliary video
(see auxiliary equipment)
MUTE
This button mutes audio to both the
headphones and the factory sound system.
AUDIO
This button allows the sound of the video
system to be heard through the vehicle
speakers, the headphones, or both.
MENU This button displays the OSM.
(See section 2-4, On-Screen Menus)
DISPLAY
This button removes the OSM from
the flat panel display and brings the user
back to the video source last selected.
It will also display the TV channel
while viewing the television.
RECALL
(Television function, see section 5-1)
VCP POWER Turns VCP on and off.
ꢁVCP Eject ꢂꢂVCP Rewind
VCP Stop ꢃꢃVCP Fast Forward
SCAN
(Television function, see section 5-1)
(Television function, see section 5-1)
Tracking control of VCP
LOCK
ꢃVCP Play
II VCP Pause
AUTO - +
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
OSMs (ON-SCREEN MENUS)
The engineering that went into the Auto Video OSM makes it very unique and easy to use.
The following steps will guide you through the OSM.
Pressing the MENU button on the system remote
will display the OSM. When in the AV1 or AV2
selection and you press MENU, the display looks
like the illustration at right:
ꢃ
PICTURE
AUDIO
From here you can scroll the position arrow up and
down using the and buttons on the remote.
ꢄ
ꢁ
OPTIONS
By pressing the ENTER button you can go to the
next screen of the OMS for picture adjustment,
audio settings or options.
ꢁ ꢄ ENTER
MENU TO EXIT
The
ꢃ
button will perform the same function as the
ENTER button. (You may find using this button to
be much easier and quicker since you will use it in
many of the adjustments in the next menu.)
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
(ON-SCREEN MENUS)
OSMs
ꢃ
BRIGHTNESS
COLOR
Selecting PICTURE will display this sub-menu.
ꢅ
You can scroll up or down to make your selection for
adjustment. Brightness, color, tint and contrast are preset
at the factory. There is a "Restore to Factory" selection
under OPTIONS which will restore the factory settings.
TINT
CONTRAST
ꢁ ꢄ ENTER
MENU TO EXIT
The PICTURE adjustments are displayed as follows:
BRIGHTNESS
TINT
COLOR
32
32
32
ꢁ ꢄ ENTER
ꢁ ꢄ ENTER
ꢁ ꢄ ENTER
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
(ON-SCREEN MENUS)
OSM
By selecting AUDIO, you can change settings that configure the tuner and
initial speaker selection of your Auto Video system.
AUDIO MODE - configures the tuner to receive STEREO or SAP (second
audio program) broadcasts. This setting effects all channels.
PICTURE
AUDIO
ꢃ
OPTIONS
NOTE: Configuring your system to SAP will effect ALL TV channels. If any
of these channels do not broadcast audio using SAP, audio will not be present.
In this mode, SAP will be displayed with the channel number on the screen.
SPK MODE (speaker mode) allows your to configure your Auto Video
system to initialize with your individual preference of audio modes.
ꢁ ꢄ ENTER
MENU TO EXIT
LAST - System audio will be configured in the same mode as the system was
previously operating. This setting allows audio through the factory sound
system or headphones, whichever was LAST set.
AUDIO MODE:
ꢃ
STEREO
ON - Sets the audio to play through the factory sound system every time the
Auto Video system is turned on. (Tune to either 88.7 or 89.1 FM,
depending on how your installer configured your system.)
SPK MODE:
LAST
OFF - This selection will cause the audio to be heard only through the
ꢁ ꢄ ENTER
headphones when Auto Video system is turned on.
MENU TO EXIT
* To change the audio mode after the Auto Video system has been turned on,
press
the SPEAKER button located on the side of the display screen or press the
AUDIO button on the remote control.
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
(ON-SCREEN MENUS)
OSMs
PICTURE
AUDIO
ꢃ
CONFIGURE
PICTURE
PWR MODE:
ꢃSTANDBY
ꢃ
OPTIONS
ꢁ ꢄ ENTER
ꢁ ꢄ ENTER
ꢁ ꢄ ENTER
MENU TO EXIT
MENU TO EXIT
MENU TO EXIT
Choosing OPTIONS - CONFIGURE provides setting that will configure the power mode. Your Auto
Video system should be configured to the STANDBY powered mode. The STANDBY selection
enables your Auto Video system components to be powered and available in a STANDBY mode when
you turn the vehicle's ignition switch. To turn the Auto Video system on, press any (of the four)
buttons located on the side of the display screen or press the LCD POWER button on the remote control.
The LCD POWER button on the remote control will also turn the Auto Video system off. You should
turn the Auto Video system off prior to stowing the system. When the Auto Video system is on, you can
momentarily turn the ignition switch OFF and then to ACC without disrupting normal system operation.
The Auto Video system will power down approximately six second after the ignition is switched off.
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
(ON-SCREEN MENUS)
OSMs
ꢃ
SAVE USER
RESTORE:
USER
PICTURE
CONFIGURE
PICTURE
AUDIO
ꢃ
ꢃ
OPTIONS
FACTORY
ꢁ ꢄ ENTER
ꢁ ꢄ ENTER
ꢁ ꢄ ENTER
MENU TO EXIT
MENU TO EXIT
MENU TO EXIT
Selecting OPTIONS - PICTURE allows you to either save or
restore the picture adjustments you have made. To save your
settings, select SAVE USER and press ENTER. Now your
brightness, color, tint and contrast are saved.
SAVE USER
RESTORE:
USER
ꢃ
FACTORY
Hint: This option works well for a night setting when you may
want to reduce the brightness of the display. The factory
settings are based on normal daytime viewing. By selecting
RESTORE you can instantly retrieve the factory settings or
your saved selections.
ꢁ ꢄ ENTER
MENU TO EXIT
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
ROSEN VCPs
3-2 Operation and features of the Rosen RVP9800 video cassette player
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
THE RVP9800 VCP
To load a VHS tape into the VCP, gently insert the cassette, label-side up, into the cassette compartment
until it stops. The VCP will continue loading the tape and begin playing it automatically.
VIDEO CASSETTE PLAYER
R
VP9800R
DEW
L-HI-FI-R
CST IN
C. STOP/EJECT button: Press this button once to
stop and a second time to eject a cassette a
cassette from the VCP.
A. POWER button: Press this button to turn the
VCP on or off. You can also use the remote
control.
D. REW button: Press this button to rewind the
tape. You can view the tape while in the rewind
mode as the tape plays.
B. Stereo Hi-Fi L/R indicators: Both indicators
glow when a Hi-Fi stereo video cassette is
being played.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
ROSEN RVP9800 VCP
E. PLAY button: Press this button to play a video
tape. If a video tape is loaded, pressing this button
will power the VCP.
H. DEW indicator: When the indicator flashes,
the Dew Sensor had been activated.
When damaging-causing moisture condensation is
detected within the VCP, the DEW Sensor circuit
automatically prevents the VCP from accepting or
playing tapes. When the dew sensor has been
activated the DEW indicator will flash. To prevent
damaging a video tape that is in the VCP when the
indicator is flashing, press EJECT and remove the
tape. Then, be sure the VCP is on so it can warm up
and dry any accumulated moisture. When the DEW
indicator stops flashing, the VCP will return to full
operation.
F. FF button: Press this button to fast forward the
tape. You can view the tape in fast forward if the
tape is playing.
G. Cassette IN indicator: This indicator glows when
there is a video cassette loaded in the VCP.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM AUDIO
4-2 Wireless Headphones
4-3 Factory Sound System Adapter (System Audio Modulator)
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRELESS HEADPHONES
Using the wireless radio frequency (RF)
Figure 1.
headphones allows some passengers to
listen to the Auto Videosystem while
others can listen to the radio.
HEADPHONE BATTERIES:
The battery compartment
To select the wireless headphones, be
sure the on/off switch is in the ‘on’
position and the volume is turned all the
way down. On/off and volume controls
are located on the right ear piece of the
headphones. The wireless headphones
will work from any position inside the
vehicle. The headphones are equipped
with a fine tuning adjustment on the
bottom of the left ear piece. Turn up the
volume until you hear static or system
sound. To tune out static or receive a
stronger stereo signal use this
is located on the right ear piece.
Replace with to "AAA" batteries
when needed. See Figure 2-B
Figure 2.
FINE TUNING:
Your RF headphones operate within
a narrow radio frequency band and need
to be adjusted when you first put them on.
To do this there is a adjustment on the
bottom of the left ear piece, turn the
adjustment until the sound is clear and
static free.
adjustment. Once you have a good
signal, turn the volume up to desired
level.
WARNING: To avoid potential damage to
your hearing, always turn the headphone
volume all the way down before placing them
over your ears. Once they are on, adjust the
volume to a comfortable level.
See figure 2-H
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM AUDIO MODULATOR
When desired, Auto Video system sound can be enjoyed by all passengers in your vehicle through
the factory radio sound system. Even though you cannot see the Rosen Audio Modulator because it is
installed behind the dashboard, it enables the audio signal from the video source you select to work
with your vehicle radio. Select the AUDIO button on the remote or the SPEAKER button on the
LCD case. The monitor will display "SPEAKER ON". Then just tune to 88.7 FM to hear the sound
and use the radio controls to adjust volume. You may want to preset one of your radio buttons to 88.7
FM to make operating the system quick and easy.
You also are able to preselect what mode your system's audio will power up in. Refer to OMS 4-3 for
configuring the audio of your system.
1
2
3
4
+12 VDC 100 mA
GND
RIGHT RETURN
LEFT AUDIO
N/C
5
6
7
8
LEFT RETURN
N/C
RIGHT AUDIO
7
6
4
8
5
3
1
2
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
TV TUNER
5-2 TV Tuner OSM (On-Screen Menu)
5-6 TV Tuner Remote Control Functions
5-7 TV Antenna System
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
TV TUNER OSM
Pressing the MENU button on the system will display the OSM.
If the system is in the TV mode and you press MENU, the display
looks like the diagram to the left. From here you can toggle the
position arrow up and down using the ꢄ ꢁ buttons on the
remote. By pressing the ENTER button, you can go to the next
screen of the OSM for either picture adjustment, audio settings,
ꢃ
PICTURE
AUDIO
OPTIONS
TUNING
options, or tuning. Using the
ꢃ
button in this stage will preform
ꢁ ꢄ ENTER
the same function as the ENTER button. (You may find using this
button to be much easier and quicker since you will use it in many
of the adjustments.)
MENU TO EXIT
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
TV TUNER OSM
PWR MODE:
INSTANT
SCAN TYPE:
PICTURE
AUDIO
ꢃ
CONFIGURE
PICTURE
ꢃ
OPTIONS
TUNING
ꢃ
RT SCAN
ꢁ ꢄ ENTER
ꢁ ꢄ ENTER
ꢁ ꢄ ENTER
MENU TO EXIT
MENU TO EXIT
MENU TO EXIT
Choosing the OPTIONS menu (diagram 1, above) and moving into
the CONFIGURE menu will allow you to set the SCAN TYPE to
either RT SCAN (Real Time Scan), or PRE-SCAN.
PWR MODE:
RT SCAN sets the tuner to always scan to the next strongest signal
when tuning up or down. This will come in handy when vehicle is in
constant motion.
INSTANT
SCAN TYPE:
ꢃPRE-SCAN
PRESCAN will automatically scan through all 69 channels, lock and
store the strongest signals. Once the PRESCAN cycle is complete,
use the UP/DOWN to instantly scroll through the preset TV channels.
The PRESCAN will take approximately 4 to 12 seconds depending
on how many signals it finds. Refer to 5-5 "Lockout features" for
locking out undesirable channels.
ꢁ ꢄ ENTER
MENU TO EXIT
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
TV TUNER OSM
PICTURE
AUDIO
AFC ON
OPTIONS
ꢃTUNING
AFC ON
00
00
ꢃ
ꢃ
ꢃ
ꢁ ꢄ ENTER
ꢃ
ENTER SCAN
ENTER SCAN
MENU TO EXIT
Choosing the TUNING menu will display the AFC (Automatic Fine Tuning Control) screen. In this
ꢃ
ꢃ
menu, you can fine tune with the
buttons. You can fine tune only the particular TV channel that
you have selected on screen. The AFC will display OFF and a green indicator will appear and move
right or left as you fine tune. The 00 display will monitor your movement. The number will increase (+)
when moving to the right and decrease (-) when moving to the left. To hold the fine setting, press ENTER
and the blue indicator will move on top of the green and the setting will be be saved. From this point, by
ꢃ
using
you can fine tune further with the green indicator. Pressing the SCAN button will allow the
ꢃ
green indicator to use 00 as the starting point for additional fine tuning. To retain the fine tuned signal,
push ENTER; your selection will be saved. You can then scroll up or down to the next channel and fine
tune it. Pushing MENU twice or DISPLAY once will bring you out of the fine tuning menu. Anytime the
tuner goes through the SCAN function, all fine tuning is reset.
(See 5-5 for SCAN)
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
TV TUNER REMOTE CONTROL FUNCTIONS
The system remote control is the main control for the
television tuner.
1
4
2
5
3
LCD
POWER
MUTE
SCAN
AUDIO
DISPLAY
Other than the two manual controls on the display for channel up and
down, all other tuner functions are controlled by the system remote
control. This section of the manual will explain the tuner control
buttons.
6
9
MENU
LOCK
7
8
ENTER
LOCK This button performs a unique function that is found
only on the Auto Video system. Pressing it will lock out
undesirable channels that the tuner may have selected
even though the reception is weak. LOCK allows you
to skip them.
0
VCP
POWER
AUTO
RECALL
TV/AV
TRACKING
When you press the LOCK button, a blue screen will
appear and CHANNEL XX LOCKED will be displayed.
Once the undesirable channels are locked, they will not
System Remote
appear in sequence during the up/down scan
selection.
ꢃ
To unlock a channel, use the up/down channel selector
ꢃ
to select the channel and press LOCK again. To unlock all
channels, push the SCAN button.
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
TV TUNER REMOTE CONTROL FUNCTIONS
While in TV tuner mode and with the system configured to
PRE-SCAN, this button will scan through all 69 channels and
preset the strongest channels to memory. When the system is
con-figuring to RT SCAN, this button will unlock all channels.
(See 5-3 for SCAN TYPE)
SCAN
There are 10 selections on the remote with blue numbers
located on the top right corner of the buttons. These are direct
access channel entry buttons. They allow you to access a
numbered channel directly instead of using the up and down
buttons. To use these, press the ENTER button first. A blue
screen will be displayed with the words ENTER CHANNEL
NUMBER followed by the number 0 ...9. When this screen
appears, enter the desired channel number with two digits.
(example: channel twelve is 12 and channel two is 02.
NUMBERS
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
TV TUNER REMOTE CONTROL FUNCTIONS
During the tuner mode, this button when
pressed will display the TV channel
while viewing the television. It will also
exit the user out of the fine tuning OSM.
DISPLAY
RECALL
The RECALL button should be thought
of as a recall/memory button and not
last display channel recall. It will allow
the toggling back and forth between two
stored channels. When one of the
desired channels is displayed on the
panel, press RECALL. The channel will
be saved and another channel will
appear. Channel surf until the second
desired channel is displayed and press
RECALL again. Now when you press
RECALL, you will be able to switch
back and forth between the two
selections.
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL EQUIPMENT
6-2 Connections for Game Systems and Camcorders
6-3 AC Power Inverter
6-4 Additional Headphones
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING GAME SYSTEMS OR CAMCORDERS
Connecting game systems or camcorders
is as easy as matching the colors of the
RCA plugs on the device to the colors on
the INPUT jacks on the TV Tuner
Interface.
Main
Po
r
e
w
VCP
Po
r
e
w
LCD
Monitor
eadphones
H
Modulator
utput
L
0
O
ace
0
v0
terf Re
Yellow -> Yellow (Video)
White -> White (Left Audio)
2
0
ner 3In-01
R
u
V
0
1
T
Antenna
V
M
Output
l
8
T
de
o
ut
L
Inp
R
V
Input
Red
-> Red
(Right Audio)
Rosen
VCP
With some games systems, an adapter is
required. These adapters are usually
available from the game system supplier.
Red
White
Yellow
Contact your local Auto Video retail
outlet when you need assistance.
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
AC POWER INVERTERS
Some video game systems, camcorders,
and other video devices require 120 VAC
"household" current instead of the 12
VDC supplied by your vehicle. These
devices require the use of an AC power
inverter (not a converter) to change the
vehicle’s 12 VDC to 120 VAC.
Power Inverter
Inverters usually plug into the vehicle's
cigarette lighter or 12 VDC power point
and the video device plugs into them. It
is absolutely essential that the inverter
be rated to supply AC power equal to
or greater than the power requirement
(in watts) of the video device. (See
specification below.) These power
inverters are available from your
dealer/installer.
Specification:
Most game systems require an inverter supplying a minimum of 140 watts output
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL HEADPHONES
Additional sets of wireless
headphones are available by
contacting your dealer/installer
or by calling Rosen Products
at 1 (800) 284-7677.
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
P
R
S
F
H
I
L
M
A
Picture adjustment
PICTURE function
Power-
2-4, 2-6
2-8
Fine tuning -
2-2
AC power inverters
Flat panel
1-2, 2-2
Purchasing
6-2
2-3
Connecting
6-2
6-3
POWER mode-
2-7
Additional headphones
Audio on/off
AUDIO mode
Headphones
Preset channel
1-4
1-4, 2-3, 2-6
2-6
Selecting/Tuning
4-2
Audio Modulator
RECALL function-
Remote control
Description-
2-3
Configuring
Description
4-3
4-3
4-3
4-3
2-3
2-4
Infrared
2-2
2-7
INSTANT function-
2-2
2-3
2-8
Frequencies
Features-
Selecting
RESTORE function-
Auto Tracking
AV1 / AV2 selection
LAST function
LOCK function
2-6
2-3
Safe operation-
SAP-
1-2
B
C
2-6
Brightness
2-5
Manual controls
Location
SAVE USER function-
SCAN function-
Speaker selection-
SPEAKER mode
STANDBY function
STATUS INDICATOR LED
Stereo-
2-8
1-4
2-3, 2-4
2-3
2-3, 5,6
MENU function
MUTE function
2-3
Channel Selection-
Color adjustment
1-4, 5-5
2-5
1-4, 2-3, 2-6
2-7
1-5
2-6
1-3
Configuring your system
Contrast adjustment
2-6
O
-
2-5
OSM
Location
1-4
2-2
2-3
2-7
2-4
1-5
2-7
D
E
Stowing
Remote control
Clearing
Deployment and storage
ENTER command
1-3
2-8
T
CONFIGURE function
Description-
OPERATING TEMPERATURE-
OPTIONS function
Technical help-
Tint adjustment-
TV / AV selection
1-2
2-5
2-3
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
V
W
T
-
-
(con't)
TV tuner
Remote control
VCP controls
VCP face controls
CASSETTE IN
2-3
Wireless headphones
Battery installation/removal
On / off switch
2-2
5-6
5-6
5-7
5-6
4-2
4-2
3-3
3-3
3-3
3-3
3-2
3-2
3-2
2-3
2-2
1-4
SCAN
DEW
LOCK
FAST FORWARD
PLAY
DISPLAY
DIRECT CHANNEL ENTRY
POWER
-
TV tuner OSM
REWIND
AFC control
5-4
STOP / EJECT
VCP power on / off
Video Cassette Player (VCP)
Video Source Selection
AUDIO function
CONFIGURE function
OPTIONS function
PICTURE function
POWER mode
2-6
5-3
2-6, 5-3
2-4, 2-6, 2-8
2-7
2-6
5-3
5-3
5-3
SAP/STEREO
SCAN TYPE function
RT scan
Pre-scan
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
All information, including illustration, is believed to be reliable. Users, however, should independently evaluate
the suitability of each product for their application. Rosen makes no warranties as to the accuracy or
completeness of the information, and disclaims any liability regarding its use or installation. Rosen's only
obligations are those in the Rosen Standard Terms and Conditions of Sale for this product, and in no case will
Rosen be liable for any incidental, indirect or consequential damages arising from the sale, resale, use or misuse
of the product. Specifications are subject to change without notice. Rosen reserves the right to make changes -
without notification to Buyer - to materials or processing that do not affect compliance with any applicable
specification.
Download from Www.Somanuals.com. All Manuals Search And Download.
E N T E R T A I N M E N T S Y S T E M S
BY
Manual Part Number 9100-0102-807
Download from Www.Somanuals.com. All Manuals Search And Download.
|