Owner’s Instructions
SW52ASP/SW62ASP
Please read this manual before using and note how to use in the proper manner.
Please be careful of keeping the manual.
Otherwise, it should be bought separately.
The User’s Manual is for common use.
Make use of the User’s Manual depending upon your washing machine model.
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
DESCRIPTION OF PARTS . . . . . . . . . . . . . . . . . . . . . . . 2
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . 3
INSTALLATION & MAINTENANCE . . . . . . . . . . . . . . . . . 4
ENVIRONMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
IN CASE OF PUMP-DRAINED WASHER . . . . . . . . . . . . . . . . . . 4
HOW TO CONNECT WATER SUPPLY HOSE . . . . . . . . . . . . . . . . 4
CLEANING THE FILTER NET . . . . . . . . . . . . . . . . . . . . . . . . . 5
HOW TO ADD THE FABRIC SOFTENER . . . . . . . . . . . . . . . . . . 5
HOW TO PUT THE DETERGENT IN . . . . . . . . . . . . . . . . . . . . . 5
CLEANING THE FILTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
LEVELLING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
WASHING INSTRUCTION. . . . . . . . . . . . . . . . . . . . . . . 7
PROCEDURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
WASH PROGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
WASHING PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . 8
CLEANING THE TUB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OPTIONAL CYCLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . 10
SPECIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Register your product at
CODE NO. : DC68-01488K-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTIONOFPARTS
WATER SUPPLY HOSE(HOT)
WATER SUPPLY HOSE (COLD)
FILTER
LID
Be sure to keep the lid
closed during washing
and spinning.
DRAIN-HOSE (PUMP)
Lint will be collected in
the filter during
washing.
FABRIC SOFTENER
DETERGENT BOX
POWER CORD
DISPENSER
BLEACH INLET
WATERFALL FLOW
SPIN BASKET
PULSATOR
GROUND LEAD
When the water pipe is
metal, make sure to cover
the end of the ground wire.
FRONT CONTROL
PANEL
ADJUSTABLE LEGS
Adjust the length
of the legs when
installing the washer.
RAT PROTECTION
PANEL
CONTROL PANEL
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETYINSTRUCTIONS
Please note that the following precautions for safety intend to prevent unpredictable danger and damage
by helping the proper use in safety.
When using hot water in washing, please make sure that the water should not exceed 50˚C.
• Plastic parts may be deformed or damaged, and an electric shock or a fire may take place.
WARNING
CAUTIONS
There might be a slight injury or damage when you
violate this instruction.
There might be serious injury or fatal accident when
you violate this instruction.
• If the plug (power supply cord) is damaged, it must be
replaced by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
• Don’t install it in the area with moisture or outdoor
where it has rain or snow
- An electric shock or a fire may take place.
• Do not pull the cord off or touch it with moist hands.
- An electric shock or a fire may take place.
• Please unplug the power supply cord when you do
not use it.
- An electric shock or a fire may take place.
• Do not bend the power supply cord by force or press it
with heavy things.
- An electric shock or a fire may take place.
• If there is dust or water on the power supply plug and
its connected part, please remove it completely.
- An electric shock or a fire may take place.
• Do not install the washer nearby electric implement or
don’t put a candle light or cigarette light on the washer.
- A fire may take place.
• Do not make your kids look into the inside of the
washer.
- If your kid falls into the washer, his life could be in
danger.
• During operation, do not put your hands or metal
materials under the washer.
- You may be hurt by spinning board beneath the
washer.
• Stay away from the washer when the bottom of the
washer sinks into the water.
• Ventilate immediately without touching the power
plug if gas is leaking.
- An electric shock or a fire may take place if it catches
flame.
- There might be an electric shock. Please wait until the
water drains out completely.
• Do not put laundry stained with gasoline, benzene,
or alcohol in the washer, and keep the materials away
from the washer.
• If the washer makes strange noise, smell or smoke,
unplug it promptly and call service agent.
- An electric shock or a fire may take place.
- An explosion or a fire may take place.
• During spinning, don’t put your hand in the spinning
tub.
- It may hurt your hands. If it does not stop within 15
seconds after you open the lid, call service agent
immediately.
• When cleaning, don’t spray water to the parts of the
washer directly.
- It may make it’s life span shorten. Also an electric
shock or fire may take place
• This appliance is not intended for use by young
children or infirm persons unless they have been
adequately supervised by a responsible person to
ensure that they can use the appliance safely.
Young children should be supervised to ensure that
they do not play with the appliance.
• Don’t use several appliances together with an outlet.
- A fire may take place due to unusual heat.
• Don’t press the button with an awl or pin.
- An electric shock or a fire may take place.
• Use the new hose-sets and old hose-sets should not
be reused.
• This appliance has to be connected to the plug
endurable to proper power consumption.
• This appliance has to be positioned so that the plug is
accessible after installation.
• If the damage is found on the current cord in use, it
should be replaced by manufacturer, service cener or
authorized person in order to avoid the risk.
• No user-serviceable parts inside. Refer any servicing to
qualified service personnel.
• Connect the grounding wire to the shell plate, and
bury it under at least 25cm of earth:elternatively,
connect the ground wire to the appropriate pin on a
properly grounded power receptacle.
Never connect the wire to a telephone line, lightning
rod, or gas pipe.
- Otherwise this may cause a mechanical error, electric
shock, fire or physical damage.
- The product warranty does not cover problems
resulting from disassembling the product.
• Do not use this product for business purposes.
• For washing machines with ventilation openings in the
base, that a carpet must not obstruct the openings.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION &MAINTENANCE
ENVIRONMENT
IN CASE OF PUMP-DRAINED WASHER
Takeoutthe
cap-hose and
connect the
outlet-hose
Be sure to join tightly
the drain hose into the
drain-outlet on the left
side of the machine.
Install the drain
hose in the position
of about 70~80cm
above the ground.
Leave some space.
Maintain at least 10cm between the washer and the wall.
Place the washer on a sturdy flat surface.
If the washer is placed on an uneven or weak
surface, noise or vibration occurs.
(allowable slope is 1 degree)
Never install the washer in a very steamy
environment or where it might be open to the rain.
Excessive moisture may cause an electrical shock hazard.
Avoid direct sunlight or heaters.
As plastic and electrical components are affected
by direct heat,never place the washer near furnaces,
boilers,etc.Do not place under direct sunlight.
HOW TO CONNECT WATER SUPPLY HOSE
Checkthetypeoftapfittingwhichisinyourlaundryandthenseeappropriateinstructionbelow:
A tap of ordinary type is desirable
In case of square tap
Take out the internal part of the connector and join it in
the following way.
Internal part
ORDINARY TAP SQUARE TAP
ROTATING TAP
1. Remove the adaptor from the
water supply hose.
4. Connect the water supply hose to
the adaptor. Pull down the part (c)
of the water supply hose .
When you release part (c) the hose
is automatically connects to the
adaptor making a 'click' sound.
c
2. First,using a "+" type screw
driver, loosen the four screws on
the adaptor.
Next,take the adaptor and turn
part(b) following the arrow for
gap about 5mm between them.
5. Connect the other end of the water
supply hose to the inlet water valve
at the top of the washer.
Screw the hose clockwise all the
way in.
a
b
3. Connect adaptor to the water
tap by tightening the screws
firmly.
6.If the water tap is a screw type,
assemble a water supply hose that
fits to the tap as shown.
Then,turn part (b) following
the arrow and put (a) and
(b)together.
c
Note : The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not
be used.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING THE FILTER NET
1. Push the upper part of
the filter and pull in.
2. Open the cover as
shown in the figure.
3. Clean the filter.
4. Close the cover and insert the lower
part of the filter in the basket first and
then push the filter with "click" sound .
HOW TO ADD THE FABRIC SOFTENER
When a proper amount (one time does) of
fabric softener is stored in the softener inlet,it is
automatically put in at the last rinsing cycle.
Do not use detergent, bleach or starch into the
Softener Inlet.
Do not open the lid during the Spin Dry cycle.
If added too early, its effectiveness will decrease.
Do not leave the softener
into the Softener
Dispenser for a long time.
Because softner
Using too much softener may produce
unsatisfactory results.
became stiff.
HOW TO PUT THE DETERGENT IN
1. Open the detergent box by pulling in the direction of the arrow as shown in the figure and then put the
powder detergent in the detergent box.
2. Put in one-time amount of detergent evenly so the detergent may not brim over the box.
Detergent Device
Put the detergent in proportion to water level
Caution : If softener is stored over the above base line, it may flow down at any time.
CLEANING THE FILTER (pump drained washer)
LEVELLING
1. Place a rag under washer filter not to wet the floor.
2. Turn the filter-cap to the left.
3. Take out the filter and remove any sludge.
4. Reassemble in reverse order.
• If the washer is not leveled with the ground, it makes the
machine tremble more or be out of order. So, make sure
that the washer is leveled properly.
SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING
THE POSITION OF THE WASHING TUB.
Open the lid of the machine, pour water into the tub up
to the level just below the pulsator, and adjust the legs so
that the pulsator is positioned at the center of the water
as shown in the figure.
Place the machine more than
10cm away from the wall.
Water
Adjust the legs on feet
for levelling .
Loosen
Lock
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
WARNING! NOTE THE FOLLOWING PRECAUTIONS TO PREVENT ELECTRICITY
LEAKAGE AND THE POSSIBILITY OF ELECTRIC SHOCK.
Earthing is necessary to prevent leakage or electric shocks caused by the electric currents leaked from the machine.
How to earth an outlet with earthing terminals
when an earthed power load is not fitted.
Outlet with earthing terminals:
Even when the internal wires of the earthing terminals are
joined, connect the earthing conductor (green) of the
machine to the tap.
When using an extension cord and a boosting transformer:
Make sure that the earthing conductor is connected.
Never make an earthing to
The telephone line, lightning rod, or gas pipe as it is
extremely dangerous in case of lightning strikes.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHINGINSTRUCTION
PROCEDURE
1. Sort the laundry into separate wash loads.
Each load of washing should contain clothing which needs the same washing conditions.
For example, you should not wash delicate clothes with very dirty work clothes.
2. Load the laundry into washing.
Before load, check all pockets, and close zippers, hooks and eyes.
3. Add the detergent. (See Page 5)
4. Add the fabric softener. (See Page 5)
5. Close the lid.
6. Press power button.
7. Choose the wash program & optional cycle. (See Page 7~9)
If you choose “SENSOR”program you don’t need to select water level.
Water level is set automatically at “SENSOR”program.
Press the START/PAUSE button.
8. Select the water level.
Before choosing the water level, remember following things.
When you choose SENSOR, HEAVY-DUTY, ECONO-WASH, WOOL program,
water level is selected “AUTO”automatically, but if you want to choose water
level manually you can select. HIGH, MEDIUM, LOW, MINIMUM
9. Select the water temperature.
Before choosing thr water temperature remember the following:
• You can choose COLD COLD+HOT HOT on all programs.
HOT is hot wash and cold rinse.
COLD is cold wash and cold rinse.
10. Close the lid and press the START/PAUSE button.
11. Do you want extra rinse?
For extra rinses press the cycle key 1 to 5 times (depending on the number of extra rinses required).
You can select up to 5 extra rinses or return to a single rinse by pressing the cycle key.
The time left display will show the number of rinses selected.
Note that the extra rinse program is not available when pause is selected or during the spin cycle.
WASH PROGRAM
SENSOR
25 min
20 min
Normal
HEAVY DUTY
26 min
ECONO WASH
18 min
WOOL
5 min
5 min
Gentle
SW52ASP
SW62ASP
Wash Time
20 min
18 min
Wash Action
Normal
Normal
HOT
HOT+COLD
COLD
HOT
HOT+COLD
COLD
HOT
HOT+COLD
COLD
HOT+COLD
COLD
Wash Temp.
Deep Rinse
HOT+COLD
COLD
COLD
COLD
COLD
SW52ASP
5 min. 30sec
5 min
5 min. 30sec
5 min
5 min. 30sec
5 min
1 min. 30sec
1 min
Spin Time
SW62ASP
SW52ASP
SW62ASP
48 min
49 min
43 min
23 min
Total Time
(High Water
level)
49 min
49 min
49 min
29 min
7
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHINGPROGRAM
CLEANING THE TUB
SENSOR Program
The best washing program is chosen automatically
Load size and water level is determined automatically
Unplug the power cord after washing.
Press the POWER button.
Press the PROGRAM button to select the HEAVY DUTY course.
Press the CYCLE button to select SOAK.
- You can select the water supply or temperature (hot/cold).
Press the WATER LEVEL button to select HIGH.
Press the START/HOLD button.
HEAVY DUTY Program
Add a dedicated detergent and close the lid.
This program is suitable for heavily soiled laundry
Load size and water level is determined automatically or you
can choose the water level you want
NOTE
- Never place laundry in the tub when cleaning inside the tub, as
this can cause discoloration or damage to the laundry.
- When doing the laundry after cleaning the tub, you may find
some impurities.
Unplug the power cord after washing.
These are just detergent residues and impurities after the tub
cleaning. Perform the rinse cycle two to three times.
ECONO Wash Program
※Keeping the tub clean
Saving your time, energy and water
Achieving Rinse performance which is determined at AS/NZS
2040
This program is suitable for lightly soiled laundry
Load size and water level is determined automatically or you
can choose the water level you want
When using the machine under humid conditions for an
extended time, various bacteria from the air may stick to
the tub and form black dirt (fungi), causing damage to the
human body.
To keep the tub clean and hygienic at all times, it is
recommended reading “Cleaning the Tub”above and using
only dedicated or recommended detergents to clean the tub
regularly at least once every one to three months.
Unplug the power cord after washing.
WOOL Program
This program is suitable for woollen clothes
Only high and medium water levels are available
Unplug the power cord after washing.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONALCYCLE
WASH ONLY
RINSE ONLY
When you choose this cycle, wash cycle is operated.
Pressing optional cycle key during washing changes the wash
time in two minute intervals.
When you choose this function, only rinse cycle is operated.
Pressing function key during rinsing changes the number of
rinses. Up to 5 rinses can be optionally selected.
The wash time can be changed to between 3 and 25 minutes.
Load size and water level is determined automatically.
Unplug the power cord after washing.
Unplug the power cord after washing.
SOAK
RINSE AND SPIN ONLY
The laundry is soaked in water so that heavy dirt can be
eliminated sufficiently.
When you choose this cycle, only rinse & spin cycle are operated
without wash cycle.
You can choose soak cycle after choosing wash program.
When you select soak function, 5 minute cycle (1 min. washing
then 4 min. pause) continue for 30 minutes before main wash
program.
Pressing cycle key during operation changes the number of
rinse (see above).
You cannot change the spin dry time using this function.
Unplug the power cord after washing.
Load size and water level is determined automatically.
Unplug the power cord after washing.
SPIN ONLY
DELAY START
When you choose this cycle, only spin cycle is operated.
Pressing cycle key during spinning only cycle changes the spin
dry time.
The spin dry time can be changed to between 1 and 7 minutes.
Unplug the power cord after washing.
This function allows you to delay the start of your chosen wash
program for 3, 4, ... 18 hours.
By pressing the delay start key you can select delayed period
for 3, 4, ... 17, 18 hours, and your washing machine will finish the
selected wash program after the delayed period.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Washing machine won’t work
Spinning does not work
Is the water tap opened?
Is the washer plugged in?
Is the power cut off?
Is the laundry spread out evenly
in the washer?
Is the washer set on a sturdy
flat surface?
Is the fuse all right?
Is there enough water?
Is the lid closed?
Water does not drain
Is the drain hose down? (No pump)
Is the drain hose frozen?
Water is not supplied
Is the water tap opened?
Is the water cut off?
Is the drain hose clogged?
If the water does not drain in 15
minutes, a buzzer will sound,
and the remaining time
Is the water supply hose or hose
connection clogged?
Is the water tap frozen?
If water is not supplied in 60
minutes, a buzzer will sound,
and the remaining time indicator
will shown “4E”.
indicator will show “5E”
While lid is opening,
the washing machine won’t work
Make sure to close the lid while washing machine is
operating.
SPECIFICATION
SW52ASP
SW62ASP
426
Power input(Watts)
Load capacity(kg)
330
5.0
6.0
Size (WxDxH)(mm)
540 X 560 X 850
31
588 X 618 X 955
38
Net Weight (kg)
Water Consumption(liters)
Water Pressure(min-max)
106(high)
50~780KPa
138(high)
50~780KPa
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care center.
Samsung Electronics Australia
7 Parkview Drive, Homebush Bay NSW 2127
1300 362 603
Download from Www.Somanuals.com. All Manuals Search And Download.
|