®
SD/CD Player/Receiver with Dot Matrix LCD and CD Changer Control
Lecteur SD - CD - récepteur avec affichage à cristaux liquides à matrice de points et commande de changeur CD
Reproductor de CD/SD/receptor con visualizador de matriz de puntos y control de cambiador de CD
REMOTE
CQ-SRX7000U
SET/ATM
BAND
OPEN
DISP
P-SET
VOL
MENU
D·M
PWR
TUNE
TRACK
SOURCE
DISC
DIM
CQ-SRX7000U
MUTE
SPC
SD/CD RECEIVER WITH FULL DOT MATRIX DISPLAY
SUB·W
TM
TEXT
¡Please read these instructions carefully before using this product and save this manual for future use.
¡Prière de lire ces instructions attentivement avant d’utiliser le produit et garder ce manuel pour l’utilisation ultérieure.
¡Lea con atención estas instrucciones antes de utilizar el producto y guarde este manual para poderlo consultar en el futuro.
Download from Www.Somanuals.com. All Manuals Search And Download.
Consignes de sécurité
Información para seguridad
MISE EN GARDE:
ADVERTENCIA:
POUR RÉDUIRE LES RISQUES D'INCENDIE OU
D'ÉLECTROCUTION, N'EXPOSEZ PAS CET APPAREIL
À LA PLUIE OU À L'HUMIDITÉ.
PARA REDUCIR EL RIESGO DE INCENDIOS O SACU-
DIDAS ELÉCTRICAS, NO EXPONGA ESTE PRODUC-
TO A LA LLUVIA NI A LA HUMEDAD.
F
R
A
N
Ç
A
I
PRECAUCIÓN:
ATTENTION:
ÉSTE ES UN PRODUCTO LÁSER DE LA CLASE 1.
LA UTILIZACIÓN DE CONTROLES, EL HACER
AJUSETES O EL SEGUIR PROCEDIMIENTOS DISTIN-
TOS DE LOS ESPECIFICADOS EN ESTE MANUAL
PODRÍA CAUSAR UNA EXPOSICIÓN PELIGROSA A
LA RADIACIÓN.
CET APPAREIL EST UN PRODUIT LASER DE CLASSE
1.
S
L'UTILISATION DE COMMANDES OU RÉGLAGES OU
L'EXÉCUTION D'OPÉRATIONS AUTRES QUE CELLES
QUI SONT INDIQUÉES DANS CE DOCUMENT PEU-
VENT RÉSULTER EN UNE EXPOSITION À UN RAYON-
NEMENT DANGEREUX.
N'OUVREZ PAS LES COUVERCLES ET N'ESSAYEZ
PAS D'EFFECTUER VOUS-MÊME DES RÉPARA-
TIONS. ADRESSEZ-VOUS À UN PERSONNEL QUALI-
FIÉ POUR TOUTE RÉPARATION.
E
S
P
A
Ñ
O
L
NO ABRA LAS CUBIERTAS NI HAGA REPARACIONES
USTED MISMO. SOLICITE LOS TRABAJOS DE SER-
VICIO AL PERSONAL CALIFICADO.
Produits laser:
Productos láser:
Longueur d'onde: 780 nm
Puissance du laser: Aucune radiation dangereuse
n'est émise avec la protection
de sécurité.
Longitud de onda: 780 nm
Potencia láser: Con protección de seguridad no se
emite radiación peligrosa.
PARA REDUCIR RIESGO DE INCENDIOS O SACUDI-
DAS ELÉCTRICAS, Y PARA EVITAR LAS INTERFER-
ENCIAS MOLESTAS, UTILICE SOLAMENTE LOS
COMPONENTES INCLUIDOS.
AFIN DE PRÉVENIR TOUT RISQUE D'INCENDIE OU
D'INTERFÉRENCES, UTILISER UNIQUEMENT LES
COMPOSANTS FOURNIS.
Déclaration d'interférence de fréquences
radio (Partie 15 des Règlements FCC):
Cet appareil numérique de Classe B est conforme
au règlement ICES-003 canadien.
Busque el número del modelo y el número de serie
ya sea en la parte trasera o en el fondo de la unidad.
Sírvase anotar dichos números en el espacio sigu-
iente, y mantenga este librete como una anotación
permanente de su compra para ayudar en la identifi-
cación en el caso de robo.
ll est recommandé de noter, dans l'espace prévu
cidessous, les numéros de modèle et de série inscrits
soit à l'arrière soit sons le fond de l'appareil, et de
conserver ce manuel comme mémorandum de
l'achat afin de permettre l'identification de l'appareil
en cas de vol.
NÚMERO DEL MODELO
NÚMERO DE SERIE
FACHA DE COMPRA
NOMBRE DE LA TIENDA
CQ-SRX7000U
NUMÉRO DE MODÈLE
NUMÉRO DE SÉRIE
DATE DE L'ACHAT
VENDEUR
CQ-SRX7000U
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
Panasonic welcomes you to our ever growing family of electronic product owners. We know that this
product will bring you many hours of enjoyment. Our reputation is built on precise electronic and mechani-
cal engineering, manufactured with carefully selected components and assembled by people who take
pride in their work. Once you discover the quality, reliability, and value we have built into this product, you
too will be proud to be a member of our family.
❏ Use This Product Safely
When Driving
Keep the volume level low enough to be aware of
road and traffic conditions.
Disc Mechanism
Do not insert coins or any small objects. Keep
screwdrivers and other metallic objects away from
the disc mechanism and disc.
When Car Washing
Never load an SD Memory Card into the CD slot.
Otherwise the main unit or the SD Memory Card
might be damaged.
Do not expose the product, including the speakers,
CDs and SD Memory Card to water or excessive
moisture. This could cause electrical shorts, fire, or
other damage.
Use Authorized Servicenters
Do not attempt to disassemble or adjust this preci-
sion product. Please refer to the Servicenter list
included with this product for service assistance.
When Parked
Parking in direct sunlight can produce very high
temperatures inside your vehicle. Give the interior a
chance to cool down before switching the unit on.
For Installation
The product should be installed in a horizontal posi-
tion with the front end up at a convenient angle, but
not more than 30˚.
Use the Proper Power Supply
This product is designed to operate with a 12 volt,
negative ground battery system (the normal system
in a North American car.)
❏ Components
¡Operating instructions. . . . . . . . . . . . . . . . . . . . . . . . . 1
¡Installation hardware . . . . . . . . . . . . 1 set (apage 40)
¡Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
¡Remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . 1
¡Lithium battery (CR2025) . . . . . . . . . . . . . . . . . . . . . . 1
¡Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
❏ Before Reading These Instructions
You can operate this unit by pressing buttons on the main unit and the remote control.
These instructions describe buttons that are concerned with operations as follows.
Example) Press [P•SETj] or [P•SETi] / [j] or [i].
(buttons on the main unit / buttons on the remote control)
Some operations can be activated by pressing buttons only on the main unit or only on
the remote control. Those cases are described in the instructions.
Example) Press [SPC] on the main unit to change the sound space.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
Contents
Safety Information........................................................................................... Page 2
Radio Frequency Interference Statement (Part 15 of the FCC Rules)..................... 2
Use this Product Safely ........................................................................................... 4
Components ............................................................................................................ 4
Before Reading These Instructions.......................................................................... 4
¢ Features .......................................................................................................... 10
¢ Remote Control Preparation ......................................................................... 11
Battery Installation and battery notes
¢ General ............................................................................................................ 12
Power, source change, volume, mute, dimmer and display change
¢ Radio ............................................................................................................... 14
Manual and automatic tuning, band selection, direct memory and preset stations
¢ CD Player ........................................................................................................ 16
Loading/ejecting a disc, CD play, track selection, search, repeat, random, scan and
title display selection
¢ SD Player ........................................................................................................ 18
Inserting/ejecting a card, SD play, track selection, search, play list selection, music list
selection, repeat, random and title display selection
¢ CD Changer .................................................................................................... 22
Disc/track selection, search, repeat, random, and scan
¢ Various Settings ............................................................................................. 24
Audio setting, sound space setting, Sub-Woofer output setting, display setting and
function setting
¢ About SD ......................................................................................................... 38
Preparation for SD play and glossary for SD
¢ Installation Guide ........................................................................................... 40
Step-by-step procedures
¢ Anti-Theft System .......................................................................................... 45
Place the removable face plate into case, install removable face plate and security
indicator
¢ Electrical Connections .................................................................................. 46
Cautions and cable wiring diagram
¢ Troubleshooting ............................................................................................. 49
Where to get service help, troubleshooting tips, error display messages and reset
switch
¢ Maintenance ................................................................................................... 55
Care of the unit, notes on CD and notes on SD
¢ Specifications ................................................................................................. 56
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
Features
S
H
This 1-DIN system is equipped with a CD player, SD player, FM/AM tuner, CD
changer controller and high power amplifier with high tone 45 W x 4 channels.
1
The SD player in this system can play only an SD Memory Card whose music data are compressed in AAC or
MP3 method.
An optional software, "RealJukebox for Panasonic" is required in recording or editing operation for SD Memory Cards.
Refer to page 38 for more information.
Full-dot colorful expressiveness <3D dot matrix display>
You can select an operation quickly because operation items are shown on the display. You can also enjoy variety of actions
and direction.
Various sound control functions
¡Space function of 7-mode DSP (apage 30), Equalizer: HEQ (Human Equalizer) and GEQ (Graphic Equalizer) (apage 24).
¡Super bass sound: DDBC (Digital Dynamic Bass Control) (apage 32), SDBB (Super Dynamic Bass Boost) (apage 26).
¡CD changer control (apage 22).
Anti-theft removable face
You can remove the panel when you leave your car (apage 45)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
Remote Control Preparation
1. Remove the battery holder.
S
H
Battery Installation
Take hold of the holder at position B and pull it out by pushing position A in
the direction shown by the arrow.
2
2. Install the battery on the battery holder.
Set a new battery properly with its (+) side facing up as shown in the figure.
3. Insert the battery holder.
Push the battery holder back into its original position.
(Back side)
Lithium battery
Position B
Battery holder
Position A
Remove and dispose of an old battery immediately.
Battery Information:
¡Battery Type: Panasonic lithium battery (CR2025)
¡Battery Life: Approximately 6 months under normal use (at room temperature)
Battery Notes
Caution: Improper use of batteries may cause overheating, an explosion
or ignition, resulting in injury or a fire. Battery leakage may damage the unit.
¡Do not disassemble or short the battery. Do not throw a battery into a fire.
¡Keep batteries away from children to avoid the risk of accidents.
¡Be careful to the disposal rules when you dispose of batteries.
Point the remote control
unit at the main unit's
sensor (REMOTE).
N
E
P
O
DISP
CQ-SRX7000U
·M
D
R
PW
REMOTE
SET/ATM
BAND
URCE
SO
DIM
SPC
P-SET
DISC
·W
SUB
VOL
TUNE
TRACK
TRIX DISPLAY
A
M
T
LL DO
ITH FU
W
MENU
EIVER
REC
D
SD/C
MUTE
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
General
[DIM] (Dimmer)
[DISP] (Display)
[VOL}] [VOL{] (Volume)
Note : When you use this unit for
the first time, a demonstration
message appears on the display.
To cancel this display, press
[DISP].
PEN
O
DISP
CQ-SRX7000U
3
·M
D
PWR
SPC
E
T
O
M
E
R
SET/ATM
BAND
SOURCE
DIM
P-SET
DISC
·W
SUB
VOL
TUNE
TRACK
ATRIX DISPLAY
ITH FULL DOT M
U
N
E
R W
/CD RECEIVE
M
SD
MUTE
[SOURCE] (Power/Source)
(Mute/Attenuator)
[MUTE]
Turn the key in the ignition until the accessory indicator
lights.
Volume
[VOL}] : Up
[VOL{] : Down
Power
Setting Range : 0 to 40
ON : Press [SOURCE].
Note : When the power is switched on by pressing
and holding [SOURCE] for more than 2 seconds, a
demonstration message appears on the display.
To cancel this display, press [DISP].
Note : The sound level for each source is
stored in memory.
(For radio, one volume setting for AM, one vol-
ume setting for all FMs)
OFF : Press [SOURCE] again for more than 1 second.
After turning off the ignition key, A security mes-
sage is displayed, and the warning alarm that
reminds you to take the panel and the SD Memory
Card is activated.
[SOURCE] (Power/Source)
[DISP] (Display)
[VOL}] [VOL{]
(Volume)
(When S-LED is set to ON apage 36)
Source
[MUTE]
(Mute/Attenuator)
Press [SOURCE] to change the source.
Radio
CD Player
(When a CD is in the player)
MUTE/ATT (Attenuator)
MUTE/ATT ON : Press [MUTE].
MUTE/ATT OFF : Press again.
SD Player
Decreasing volume range depends on setting.
(MUTE/ATT setting apage 36)
(When a SD Memory Card is in the player)
CD Changer
(When a CD changer is connected and magazine is in the changer)
: No sound
AUX In
: Decrease the volume to
1/10 of previous level.
(When AUX-IN setting is set to ON) (apage 36)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
Dimmer
Press [DIM] on the main unit to change the dimmer level.
4
Default : DIMMER 2
(With side marker lights ON)
DIMMER 3
(With side marker lights OFF)
DIMMER 3
(Brighter)
DIMMER 2
(Medium)
DIMMER 1
(Darker)
Notes :
¡Set the display brightness for each of the cases in which the side marker lights are on and the side marker lights are off.
¡Be sure to connect the illumination lead. (apage 46)
Display Change
When Power is ON
Press [DISP].
Mode & Spectrum
Analyzer Display
Mode Display *1
Spectrum Analyzer Display *2
*1 The title information can be
displayed in the CD/SD
mode. (apage 17 and 21)
*2 If you press a button, the
Mode & Spectrum Analyzer
Display appears for 5 sec-
onds.
Display OFF *3
Mode & Clock Display
*3 If you press a button, the
light is turned on, the Mode
Display appears, and the
light is turned off approxi-
mately 5 seconds later.
Notes :
¡Set the Spectrum Analyzer pattern in a separate procedure. (apage 34)
¡“ADJUST” is displayed before adjusting the clock. (Adjustment apage 34)
AUDIO Indicator
Press and hold [DISP] for more than 2 seconds.
Indicators which are not displayed on Mode Display are displayed.
(Sound, sound space and SD data information etc.)
Press [DISP] again to cancel.
When Power is OFF
Press [DISP].
Clock Display
Display OFF
(Back light is on)
(Back light is off)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
Radio
[D · M] (Direct memory)
[BAND]
(Auto preset memory)
Radio Mode Display
OPEN
DISP
CQ-SRX7000U
5
·M
D
R
PW
OTE
REM
SET/TM
SOURCE
BAND
DIM
SPC
P-SET
·W
SUB
VOL
TUNE
Frequency
TRACK
Band
MENU
Stereo Indicator
SD/CD RECEIVER WITH FULL DOT MATRIX DISPLAY
DISC
MUTE
[SOURCE]
(Source)
Note: The stereo indicator lights during
reception of an FM stereo broadcast.
[TUNE]] [TUNE[] (Tune)
[P•SET}] [P•SET{] (Preset station)
Radio Mode
1
Press [SOURCE] to change to radio
mode.
[SOURCE] (Source)
Band
2
Press [BAND].
FM1
FM2
FM3
AM
[1] to [6] (Preset station)
[BAND] (Auto preset memory)
[]] [[] (Tune)
Tuning
3
[TUNE[] / [[] : Up
[TUNE]] / []] : Down
[}] [{]
(Preset station)
Press and hold [TUNE[] or [TUNE]] /
[[] or []] for more than 0.5 seconds,
then release. Seeking will start.
Direct Memory
Your favorite radio station can be memorized in the D·M button and you can call back radio stations just by pressing the
button whatever the current sound source is, even if the power is off.
Default : FM 87.9 MHz
Memorize
Recalling the Direct Memory
Press [D · M] on the main unit.
q Select a band and frequency (step q, w and e on
Press [D · M] on the main unit again to cancel and
the above.)
return to the previous source.
w Press and hold [D · M] on the main unit for more
than 2 seconds. Frequency blinks once and is
saved in the memory.
Notes:
¡New station is overwritten on existing saved station after following memorization procedure.
¡Only the following operations are practicable while the Direct Memory radio station is being played: turning the
power on or off, switching the source, adjusting the volume, turning on or off Mute (Attenuator), adjusting dimmer,
switching the display, and loading a disc or a card.
Cancel the Direct Memory function to resume the normal operations.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
One-touch selection of a preset station
6
Up to 6 stations each can be saved in the FM1, FM2, FM3 and AM preset station memories.
Select a band and frequency (step q, w and e on the previous page)
q Press and hold [P•SET}] or [P•SET{] / [}] or [{] for more than
2 seconds until the preset number blinks.
w Press [P•SET}] or [P•SET{] / [}] or [{] to select a preset num-
ber.
e Press and hold [P•SET}] or [P•SET{] / [}] or [{] for more than
Manual Preset
2 seconds to memorize.
Memory
The display blinks once, and a receiv-
ing station is saved in the memory.
Manually save a station in
the preset memory.
Note: Frequency setting can be performed even after selecting a preset num-
ber.
Entering numbers directly from the remote control
Select a band and frequency (step q, w and e on the previous page)
Press and hold [1] to [6] on the remote control for more than 2 seconds.
Select a band (step q, w on the previous page)
Press and hold [BAND] for more than
2 seconds.
Scanning
Auto Preset
Memory
Automatically save strong
stations in the preset
memory.
¡The 6 strongest available stations will be automatically saved in the memory
under preset numbers 1 to 6.
¡Once set, the preset stations are sequentially scanned for 5 seconds each.
¡To stop the scanning, press [P•SET}] or [P•SET{] / [}] or [{].
(Pressing [1] to [6] on the remote control also can stop the scanning.)
Note: New stations are overwritten on existing saved stations after following this procedure.
Select a band (step q, w on the previous page)
Press [P•SET}] or [P•SET{] / [}] or [{] to select the preset number
for tuning in the preset station.
Preset Station
Calling
Entering numbers directly from the remote control
Press [1] to [6] on the remote control.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
CD Player
EN
OP
U
0
00
7
DISP
PWR
X
R
-S
Q
C
·M
D
REMOTE
SET/ATM
SOURCE
D
N
A
B
DIM
Open the Front Panel
1
2
SPC
P-SET
·W
SUB
7
VOL
NE
TRACK
AY
L
TU
ISP
D
IX
TR
A
M
Press [OPEN] on the front panel.
T
O
D
ULL
F
ITH
W
R
E
MENU
IV
E
C
E
R
D
/C
SD
DISC
E
T
U
M
Disc Insert
Playback starts. Close the front panel.
Notes :
Label Side
¡Do not insert a disc when this indicator
lights.
¡Loading a CD when the power is off allows the
power to be turned on.
¡Ejecting the CD when the unit is in the CD
mode allows the power to be turned off.
To Stop and Eject the Disc
Press [uCD]
CD Player Mode Display
[DISP] (Return)
[BAND] (Set)
OPEN
D
IS
P
CQ-SRX7000U
·M
D
PWR
REMOTE
SET/TM
SOURCE
BAND
DIM
Play Time
SPC
P-SET
·W
SUB
VOL
U
Track Number
When a CD is inside
(Blinks during CD play)
TUNE
TRACK
ITH FULL DOT MATRIX DISPLAY
EN
M
SD/CD RECEIVER W
DISC
[SOURCE]
(Source)
MUTE
Scan, Random and
Repeat Indicator
[TRACK 1] [TRACK2] (Track)
[MENU]
(Menu)
[P•SET}] [P•SET{] (Select)
When CD is in the player
Press [SOURCE] to change to CD player mode
and playback starts.
[SOURCE]
(Source)
[4] (Random)
[6] (Repeat)
[SEL] (Menu)
Track Selection
[5] (Scan)
[TRACK2] / [[] : Next track
[TRACK1] / []] : Beginning of the current
[}] [{]
(Select)
track
[]] [[] (Track)
Previous track
(Press twice.)
[BAND]
(Set)
[DISP]
(Return)
Track Search
Press and hold.
[TRACK2] / [[] : Fast forward
[TRACK1] / []] : Fast reverse
Cautions:
Never load an SD Memory Card into the CD slot. Otherwise the main unit or the SD Memory Card might be damaged.
¡
¡To avoid damaging the front panel, do not push it down or place objects on it while it is open.
¡Do not use irregularly shaped CDs.
¡Do not pinch your finger or hand in the front panel. Do not insert foreign matter into the disc and card slots.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
CD Mode Setting from Menu
q Press [MENU] / [SEL] during CD playing.
8
CD Menu Display
w Press [P•SET}] or [P•SET{] / [}] or [{] to select an item.
e Press [BAND] to switch on or off in turn.
Notes:
¡Operations except setting should be performed after returning to the mode display.
¡If no keys have been pressed for more than 15 seconds, the display returns to the previous one after changing to the
menu display.
¡Press [DISP] to return to the regular mode.
Play Setting
: All the available tracks are played in a random
sequence.
ON
Select
RAND
Random Play
Scan Play
: Cancel
OFF
: The first 10 seconds of each track play in
sequence.
ON
Select
SCAN
: Cancel
OFF
: Repeat the current selection.
: Cancel
Select
REP
ON
Repeat Play
OFF
Title Information
: Display
ON
Select
TITLE
: No display
OFF
Title Display
Title Scroll
¡“NO TITLE” is displayed when there is no information.
¡When the title display is set to ON, the mode display appears.
: Continuous scroll
ON
Select
: Scroll stops after a circle scroll
Press and hold [BAND] for more than 2
seconds to have an another circle scroll.
OFF
TITLE SCROLL
Direct Play Setting from Remote Control
Random, scan and repeat can be set by the remote control when the menu is not displayed.
Press [4] (Random) / [5] (Scan) / [6] (Repeat) on the remote control. Press again to cancel.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
SD Player
EN
OP
Open the Front Panel
1
2
0U
00
7
DISP
PWR
X
R
-S
Q
C
·M
D
Press [OPEN] on the front panel.
REMOTE
SET/ATM
SOURCE
D
N
A
B
9
DIM
SPC
P-SET
·W
SUB
VOL
E
Y
N
TU
TRACK
PLA
IS
D
IX
TR
A
M
T
O
D
L
L
FU
ITH
W
R
E
MENU
IV
E
C
E
D
/C
SD
R
DISC
Memory Card Insert
E
T
U
M
q Load a card by pushing the center of the
back of the card until it is locked.
w Playback starts. Close the front panel.
Notes :
¡Loading an SD Memory Card when the power
is off allows the power to be turned on.
¡Ejecting the SD Memory Card when the unit is
in the SD mode allows the power to be turned
off.
Cut Side
Label Side
To Stop and Eject the SD Memory
Card
Press the center of the back of the card to be
unlocked.
Push
SD Player Mode Display
Track Number
Play Time
[DISP]
(Data information)
OPEN
D
IS
P
CQ-SRX7000U
·M
D
PWR
REMOTE
SET/ATM
BAND
SOURCE
When an SD Memory Card is inside
(Blinks during SD play)
Random and Repeat
DIM
Play List Number
SPC
P-SET
·W
SUB
VOL
TUNE
TRACK
MENU
Indicator
SD/CD RECEIVER WITH FULL DOT MATRIX DISPLAY
DISC
[SOURCE]
MUTE
(Source)
When an SD Memory Card is in the
player
[TRACK 1] [TRACK2] (Track)
Press [SOURCE] to change to SD player mode
[P•SET}] [P•SET{] (Play list select)
and playback starts.
Track Selection
[SOURCE]
[TRACK2] / [[] : Next track
(Source)
[TRACK1] / []] : Beginning of the current
track
Previous track
(Press twice.)
[}] [{]
(Play list select)
[]] [[] (Track)
[DISP]
Track Search
(Data
Press and hold.
information)
[TRACK2] / [[] : Fast forward
[TRACK1] / []] : Fast reverse
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
¡Refer to the "About SD" (a page 38) and "Notes on SD Memory Card" (a page 56) for the information of the SD
Memory Card.
10
¡Refer to the Operating Instructions and online help for the PC software “RealJukebox for Panasonic” for the
information of the play list etc.
Play List Selection
Press [P•SET}] or [P•SET{] / [}] or [{] to select the play list
during SD playing.
Playback of the track in the selected play list starts.
Play List Number
Notes :
¡Same play list will be played continuously after all tracks are played in
the selected play list.
¡The play list selection is also available from the menu display
(apage 20).
When play list number 2 is selected.
To Return to All Track Playing
Select play list number “0” to return to the all track playback.
SD Memory Card Data Information
Press and hold [DISP] for more than 2 seconds to display the SD Memory Card data information.
While playing music that was compressed in the
AAC compression format
While playing music that was compressed in the
MP3 compression format
AAC
MP3
compression
compression
format
format
Bit rate
Bit rate
Cautions:
Never load an SD Memory Card into the CD slot. Otherwise the main unit or the SD Memory Card might be damaged.
¡
¡To avoid damaging the front panel, do not push it down or place objects on it while it is open.
¡Confirm that the direction of the card is correct, and that the card is not inverted. Forced loading may cause trouble.
¡Do not pinch your finger or hand in the front panel. Do not insert foreign matter into the disc and card slots.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
(continued)
SD Player
S
H
SD Mode Setting from Menu
q Press [MENU] / [SEL] during SD playing.
11
SD Menu Display
w Press [P•SET}] or [P•SET{] / [}] or [{] to select an item.
e Press [BAND] to switch on or off in turn.
e Press [BAND] to set. (Play list and music list)
Notes:
¡Operations except setting should be performed after returning to the mode display.
¡If no keys have been pressed for more than 15 seconds, the display returns to the previous one after changing to the
menu display.
¡Press [DISP] to return to the regular mode.
Play Setting
: All the available tracks are played in a random
sequence.
: Cancel
ON
Select
RAND
OFF
Random Play
Repeat Play
Play List
¡When play list is playing, all the available tracks from the
play list are played in random sequence.
Select
REP
: Repeat the current selection.
: Cancel
ON
OFF
From the play list display,
q Select your favorite play list with pressing [P•SET}] or
[P•SET{] / [}] or [{].
Refer to the Operating
Instructions and online
help for the PC software
“RealJukebox for
w Press [BAND] to set.
Select
PLAY LIST
Playback of the track in the
selected play list starts.
Panasonic” for the infor-
mation of the play
list,etc.
¡Select “00-DEFAULT PLAYLIST” to return to the all track
playback.
Music List
From the music list display,
q Select your favorite track with pressing [P•SET}] or
[P•SET{] / [}] or [{].
When all track playback
Display all tracks in the
SD Memory Card.
Select
w Press [BAND] to set.
MUSIC LIST
Playback of the selected
track starts.
When play list playback
Display all tracks in the
play list.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
Title Information
12
: Display
: No display
ON
Select
TITLE
OFF
Title Display
Title Scroll
¡“NO TITLE” is displayed when there is no information.
¡When the title display is set to ON, the mode display appears.
: Continuous scroll
ON
Select
: Scroll stops after a circle scroll
Press and hold [BAND] for more than 2
seconds to have an another circle scroll.
OFF
TITLE SCROLL
Direct Play Setting from Remote Control
Random and repeat can be set by the remote control when the menu is not displayed.
Press [4] (Random) / [6] (Repeat) on the remote control. Press again to cancel.
[DISP] (Return)
[BAND] (Set)
OPEN
D
IS
P
CQ-SRX7000U
·M
D
PWR
REMOTE
SET/ATM
SOURCE
BAND
DIM
SPC
P-SET
·W
SUB
VOL
TUNE
TRACK
U
N
E
M
SD/CD RECEIVER WITH FULL DOT MATRIX DISPLAY
DISC
MUTE
[MENU]
(Menu)
[P•SET}] [P•SET{] (Select)
[4] (Random)
[6] (Repeat)
[SEL] (Menu)
[BAND] (Set)
[DISP] (Return)
[}] [{]
(Select)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
CD Changer
CD changer functions are designed for optional Panasonic CD changer unit.
Connect the CD changer, and load a magazine.
Notes :
13
¡Loading a magazine when the power is off allows the power to be turned on.
¡Ejecting the magazine when the unit is in the CD changer mode allows the power to be turned off.
CD Changer Mode Display
Play Time
Track Number
[DISP] (Return)
[BAND] (Set)
OPEN
D
IS
P
CQ-SRX7000U
·M
D
PWR
REMOTE
SET/ATM
SOURCE
BAND
DIM
SPC
P-SET
·W
SUB
When a CD changer is
connected
(Blink during CD changer
play)
VOL
Disc Number
TUNE
TRACK
ITH FULL DOT MATRIX DISPLAY
U
EN
M
SD/CD RECEIVER W
DISC
[SOURCE]
(Source)
UTE
M
Scan, Random and
Repeat Indicator
[TRACK 1] [TRACK2] (Track)
[MENU]
(Menu)
[P•SET/DISC}] [P•SET/DISC{] (Select)
CD Changer Mode
1
Press [SOURCE] to change to CD chang-
er mode and play back starts
[SOURCE] (Source)
Note : Load a magazine with CDs when
“NO DISC” is displayed.
Disc Selection
2
3
[4] (Random)
[5] (Scan)
[DISC}] / [}] : Next disc.
[6] (Repeat)
[DISC{] / [{] : Previous disc.
[}] [{]
(Disc/Select)
[SEL] (Menu)
[]] [[]
(Track)
[DISP]
(Return)
Track Selection
[BAND]
(Set)
[TRACK2] / [[] : Next track.
[TRACK1] / []] : Beginning of the
current track.
Previous track
(Press twice)
Track Search
Press and hold.
[TRACK2] / [[] : Fast forward
[TRACK1] / []] : Fast reverse
Caution: Do not use irregularly shaped CDs.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
CD Changer Mode Setting from Menu
14
q Press [MENU] / [SEL] during CD changer playing.
CD Changer Menu Display
w Press [P•SET}] or [P•SET{] / [}] or [{] to select an item.
e Press [BAND] to switch on or off in turn.
Notes:
¡Operations except setting should be performed after returning to the mode display.
¡If no keys have been pressed for more than 15 seconds, the display returns to the previous one after changing to the
menu display.
¡Press [DISP] to return to the regular mode.
Play Setting
Select
RAND
ON
: All the available tracks on all discs in the magazine
are played in a random sequence.
: Cancel
OFF
Random Play
Select
D. RAND
ON
: All the available tracks on current discs are played in
a random sequence.
: Cancel
OFF
Select
SCAN
ON
: The first 10 seconds of each track on the discs plays
in sequence.
: Cancel
OFF
Scan Play
Select
D. SCAN
ON
: The first track of all the discs in the magazine is
played for 10 seconds each.
: Cancel
OFF
Select
REP
ON
: Repeat the current selection.
: Cancel
OFF
Repeat Play
Select
D. REP
ON
: Repeat the current disc selection.
: Cancel
OFF
Direct Play Setting from Remote Control
Random, scan and repeat can be set by the remote control when the menu is not displayed.
Press [4] (Random) / [5] (Scan) / [6] (Repeat) on the remote control. Press again to cancel.
Press and hold [4] (Random) / [5] (Scan) / [6] (Repeat) for more than 2 seconds on the remote control to activate disc
random, disc scan and disc repeat. Press and hold again for more than 2 seconds to cancel.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
Various Settings
[BAND] (Set)
OPEN
D
IS
P
AUDIO Menu Display
CQ-SRX7000U
·M
D
PWR
REMOTE
SET/TM
SOURCE
15
BAND
DIM
SPC
P-SET
·W
SUB
VOL
TRACK
TUNE
U
EN
M
SD/CD RECEIVER WITH FULL DOT MATRIX DISPLAY
DISC
[DISP]
(Return)
UTE
M
[TUNE]] [TUNE[] (Select)
[MENU]
(Menu)
[P•SET}] [P•SET{] (Select/Adjust)
Tone Quality
Press [P•SET}] or
[P•SET{] / [}] or
(Human Equalizer/HEQ)
[{] to select
There are 49 ready patterns to make presetting
easier.
HEQ
Default : FLAT(0)
Setting range : 1 - 3 for each patterns (49 pat-
terns)
Press [BAND] to set.
Press [MENU] / [SEL] to
select AUDIO.
Current Source
AUDIO
Save Your Tone Quality
Preference
PICTURE
(Graphic Equalizer/GEQ)
You can adjust the level from bass to treble
in each of 7 frequency bands. Up to 5 tone
quality preferences can be saved in memory.
( Preset memory 1 to 5 )
Press [P•SET}] or
[P•SET{] / [}] or
[{] to select
FUNCTION
GEQ
Default : 0 dB for each frequency
Setting range : –12 to +12 in 2 dB step
Press [BAND] to set.
A tone quality that excludes blurred
bass and is comfortable to listen to is
already saved under preset number 6.
Note: You can not save under preset
number 6.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
<Audio Setting>
[BAND] (Set)
S
H
Notes:
¡Operations except setting should be performed after
returning to the mode display.
16
¡If no keys have been pressed for more than 15 sec-
onds, the display returns to the previous one after
changing to the menu display.
[SEL] (Menu)
[}] [{]
(Select/Adjust)
[]] [[]
(Select)
¡Press [DISP] to return to the regular mode.
[DISP] (Return)
• Recreation
• Enjoyable drive
• Stress relieving
• Refresh
[P•SET}] / [}] : Heavy bass
Heavy
[P•SET{] / [{] : Light bass
[TUNE[] / [[] : Sharp treble
[TUNE]] / []] : Soft treble
• Listen to the music
Sharp
Soft
Press [BAND] to set.
Light
• Safe drive
• Rhythmical
• Awakening
• Calm down
• Concentration
GEQ Adjustment
Adjust the level for each frequency.
GEQ Adjusting Display
q Press [TUNE[] or [TUNE]] / [[] or []] to
move the cursor.
w [P•SET}] / [}] : Upper level.
[P•SET{] / [{] : Lower level
Memorize
Calling Back the Preset Tone Quality
After changing to the GEQ adjusting display,
q Position the cursor on “P•SET” using [TUNE[]
or [TUNE]] / [[] or []].
w Press [P•SET}] or [P•SET{] / [}] or [{]
to select one of the preset numbers 1 - 6
q Position the cursor on “P•SET” using [TUNE[]
or [TUNE]] / [[] or []].
w Press [P•SET}] or [P•SET{] / [}] or [{]
to select preset number 1 to 5.
e Adjust the level for each frequency.
Note: Memorizing and callback can not be performed
Note: New setting is overwritten on existing saved set-
by using [1] to [6] on the remote control.
ting after following this procedure.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
(continued)
Various Settings
[BAND] (Set)
OPEN
D
IS
P
AUDIO Menu Display
CQ-SRX7000U
·M
D
PWR
SPC
REMOTE
SET/TM
SOURCE
17
BAND
DIM
P-SET
·W
SUB
VOL
TUNE
TRACK
ITH FULL DOT MATRIX DISPLAY
U
EN
M
SD/CD RECEIVER W
DISC
MUTE
[DISP]
(Return)
[TUNE]] [TUNE[] (Select/Adjust)
[P•SET}] [P•SET{] (Select/Adjust)
[MENU]
(Menu)
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Balance and Fader
You can adjust the sound balance among the
front, rear, right and left speakers.
Default : L/R(Balance) : Center
BAL/FAD
FRONT/REAR(Fader) : Center
Setting range : 15 levels each
Press [BAND] to set.
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Sound Image
Press [MENU] / [SEL] to
select AUDIO.
(Position)
POSI
You can adjust the sound image in accordance
with a listener's position.
Current Source
AUDIO
Press [BAND] to set.
Default : OFF
Rear Speakers as Sub-Woofers
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
(Super Base Control Sub-Woofer/SBC-SW)
PICTURE
You can utilize the rear speaker connected to
the built-in amplifier as Sub-Woofers that out-
puts only bass.
SBC SW
FUNCTION
Press [BAND] to set.
Default : OFF
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Bass Enhancement
(Super Dynamic Bass Boost/SDBB)
SDBB
The bass of the 4 speakers connected to the
built-in amplifier is enhanced, so that you can
enjoy heavy bass sound.
Press [BAND] to set.
Default : OFF
26
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
<Audio Setting>
[BAND] (Set)
S
H
Notes:
¡Operations except setting should be performed after
returning to the mode display.
18
¡If no keys have been pressed for more than 15 sec-
onds, the display returns to the previous one after
changing to the menu display.
[SEL] (Menu)
[}] [{]
(Select/Adjust)
[]] [[]
(Select/Adjust)
¡Press [DISP] to return to the regular mode.
[DISP] (Return)
L/R (Balance)
FRONT/REAR (Fader)
[TUNE[] / [[] : Right enhanced
[P•SET}] / [}] : Front enhanced
[TUNE]] / []] : Left enhanced
[P•SET{] / [{] : Rear enhanced
Press [BAND] to set.
Press [BAND] to set.
Press [P•SET}] or [P•SET{] / [}] or [{] to change.
: Front right
: Front left
: Front
: All seats
RIGHT
LEFT
OFF
FRONT
REAR
: Rear
Press [BAND] to set.
Press [P•SET}] or [P•SET{] / [}] or [{] to change.
: Regular Output (Stereo)
OFF/STEREO
ON/MONO
: Bass Enhancement (Monaural)
SBC-SW ON
¡Adjust the Sub-Woofer output level (apage 32). It is also interlocked with the preout (rear speaker output).
¡BAL/FAD, POSI, SDBB and SPACE (apage 30) settings for rear speaker output will be invalid.
Press [BAND] to set.
Press [P•SET}] or [P•SET{] / [}] or [{] to change.
: Variable, low
: Variable, high
: Fixed, low
: Normal output
TYPE 1
TYPE 2
TYPE 3
TYPE 4
OFF
dB
12
8
TYPE1(Variable: low)
TYPE2(Variable: high)
TYPE3(Fixed: low)
TYPE4(Fixed: high)
¡Variable : Bass enhancement
along with the volume
¡Fixed : Bass enhancement
with fixed range
: Fixed, high
OFF
0
300Hz
Frequency
27
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
(continued)
Various Settings
[BAND] (Set)
OPEN
D
IS
P
AUDIO Menu Display
CQ-SRX7000U
·M
D
PWR
SPC
REMOTE
SET/TM
SOURCE
19
BAND
DIM
P-SET
·W
SUB
VOL
TUNE
TRACK
ITH FULL DOT MATRIX DISPLAY
U
EN
M
[DISP]
(Return)
SD/CD RECEIVER W
DISC
MUTE
[TUNE]] [TUNE[] (Select/Adjust)
[P•SET}] [P•SET{] (Select)
[MENU]
(Menu)
Preparations :
¡Connect an optional center speaker and power amplifier. (apage 47)
¡Turn off the DSP effect before adjusting the volume level and delay time of the center speaker. (Refer to the following.)
Center Speaker Volume
Press [MENU] / [SEL] to
select AUDIO.
Level
Default : 0
Press [P•SET}] or
[P•SET{] / [}] or [{]
Current Source
Setting range : – ∞, –10 to +10 in 2 dB step
to select
AUDIO
CENTER
Center Speaker Delay
Press [BAND] to set.
PICTURE
Time
FUNCTION
Default : 0
Setting range : –10 to +10
(1 step = 0.001 seconds)
Center Speaker Volume Adjustment Procedure
Preparations :
Set the following before adjusting the volume of the center speaker.
¡Sound space : SPACE OFF (apage 30)
¡Sound space range (WIDE / NARROW) : 0 (apage 30)
1. Adjust the center speaker volume.
Adjust the volume so that middle tone
such as vocal is oriented toward the front
center.
2. Adjust the sound space and its range
(DSP effect).
28
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
<Audio Setting>
[BAND] (Set)
S
H
Notes:
¡Operations except setting should be performed after
returning to the mode display.
20
¡If no keys have been pressed for more than 15 sec-
onds, the display returns to the previous one after
changing to the menu display.
[SEL] (Menu)
[}] [{]
(Select)
[]] [[]
(Select/Adjust)
¡Press [DISP] to return to the regular mode.
[DISP] (Return)
[TUNE[] / [[] : Up
[TUNE]] / []] : Down
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
– ∞ : No sound from the center speaker
LEVEL
Press [BAND] to set.
[TUNE[] / [[] : Longer delay time, farther sound image (Center speaker output
timing is delayed)
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
[TUNE]] / []] : Shorter delay time, closer sound image (Center speaker output
timing is advanced)
0 : The output timing of the center speaker is synchronized with that of the other
speakers.
DELAY
Press [BAND] to set.
3. Adjust the center speaker volume again.
Adjust the center speaker delay time and vol-
ume to suit with the sound space setting.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
(continued)
Various Settings
[P•SET}] [P•SET{] (Select)
[DISP] (Return)
21
Sound Space Setting Display
N
PE
O
DISP
CQ-SRX7000U
·M
D
R
PW
REMOTE
SET/ATM
BAND
RCE
SOU
DIM
SPC
P-SET
·W
SUB
VOL
TUNE
TRACK
PLAY
DIS
TRIX
ITH FULL DOT MA
MENU
D
RECEIVER
W
SD/C
DISC
MUTE
[SPC] (Sound space)
[TUNE]] [TUNE[] (Adjust)
Sound Space Reproduction
(SPACE)
Sound space can be made in a car like being in a concert hall.
Sound space range can be adjusted.
Press [SPC] on the main
unit to change to the sound
space setting menu mode.
Default : Sound space....SPACE OFF
Sound range....0
Setting range : Sound space....8 types (including SPACE OFF)
Sound space range....–3 to +3
Sound space is available for each mode (AM, FM, CD, SD, CD
Changer and AUX-IN).
30
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
<Sound Space Setting>
S
H
Notes:
¡Operations except setting should be performed after
returning to the mode display.
22
¡If no keys have been pressed for more than 15 sec-
onds, the display returns to the previous one after
changing to the menu display.
¡Press [DISP] to return to the regular mode.
[}] [{]
(Select)
[]] [[]
(Adjust)
[DISP] (Return)
Sound Space Type Setting
Press [SPC] on the main unit to change the sound space type.
([P•SET}] and [P•SET{] / [}] and [{] are also available to change the sound space type.)
SPACE OFF
CINEMA
LIVE HOUSE
VOCAL
CONCERT HALL
DISCO
JAZZ CLUB
STADIUM
Sound Space Range (WIDE / NARROW)
[TUNE[] / [[] : Wide space atmosphere
[TUNE]] / []] : Narrow space atmosphere
31
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
(continued)
Various Settings
N
E
P
O
P
IS
D
-SRX7000U
CQ
DDBC SUB-W Menu Display
·M
D
R
TE
O
M
E
R
SET/ATM
E
C
R
U
O
S
[DISP]
(Return)
AND
B
23
DIM
PC
S
P-SET
·W
B
U
S
VOL
TUNE
PLAY
IX DIS
ATR
M
T
R
A
C
K
T
ULL DO
F
ITH
W
MENU
ER
IV
E
EC
R
D
/C
SD
DISC
TE
MU
[SPC] (DDBC SUB-W menu)
[TUNE]] [TUNE[] (Select/Adjust)
[P•SET}] [P•SET{] (Select)
These adjustments are effective when Sub-Woofers are connected or when the rear speakers are used as Sub-Woofers.
(apage 26)
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Sub-Woofer Volume
(DDBC Volume Level)
Default : 0
LEVEL
Setting range : – ∞, –10 to +10 in 2 dB step
Sense of Distance
There is no delay time between speaker and
Sub-Woofer sound, so that you can enjoy
dynamic heavy bass.
(DDBC Delay Time)
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Press and hold [SPC] for
more than 2 seconds to
change to DDBC SUB-W
menu mode.
DELAY
Default : 0
Setting range : –10 to +10
(1 step = 0.001 seconds)
Bass Control
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
(DDBC Cut off Frequency)
The upper limit of the bass cut off frequency is
controlled, so that you can enjoy a clear
sound.
LPF
Default : OFF
Setting range : 4 levels (including OFF)
32
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
<Sub-Woofer Output Setting>
DDBC / Digital Dynamic Bass Control
S
H
Notes:
¡Operations except setting should be performed after
returning to the mode display.
24
¡If no keys have been pressed for more than 15 sec-
onds, the display returns to the previous one after
changing to the menu display.
[}] [{]
(Select)
[]] [[]
(Select/Adjust)
¡Press [DISP] to return to the regular mode.
[DISP] (Return)
[TUNE[] / [[] : Up
[TUNE]] / []] : Down
– ∞ : No Sub-Woofer sound
[TUNE[] / [[] : Sub-Woofer output timing is delayed than other speakers.
[TUNE]] / []] : Sub-Woofer output timing is advanced than other speakers.
0 : The output timing of the Sub-Woofers is synchronized with that of the other speakers.
Press [TUNE[] or [TUNE]] / [[] or []] to change the cut off frequency.
: Regular output, high tone included
: High tone excluded
OFF
100Hz
150Hz
200Hz
(Select the top limit of output lower frequency range.)
Follow the setting below when using an adjusting function built in an external amplifier.
¡DDBC Delay Time : 0
¡DDBC Cut off Frequency : OFF
33
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
(continued)
Various Settings
[BAND] (Set)
OPEN
P
IS
P
D
PICTURE Menu Display
CQ-SRX7000U
·M
D
PWR
SPC
REMOTE
SET/TM
SOURCE
25
BAND
DIM
P-SET
·W
SUB
VOL
TUNE
TRACK
ITH FULL DOT MATRIX DISPLAY
MENU
[DISP]
(Return)
SD/CD RECEIVER W
DISC
MUTE
[TUNE]] [TUNE[] (Select/Adjust)
[P•SET}] [P•SET{] (Select/Adjust)
[MENU]
(Menu)
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Spectrum Analyzer
Display Pattern
S·A PATTERN
Default : Pattern A
Variety : 6 types
Press [BAND] to set.
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Contrast
Allows you to adjust the display contrasts for
better viewing.
Press [MENU] / [SEL] to
select PICTURE.
CONTRAST
Current Source
AUDIO
Default : Level 3
Setting range : Level 1 to Level 5
Press [BAND] to set.
PICTURE
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Clock Display
FUNCTION
Default : ON (Not adjusted. “--:--” will appear.)
CLOCK
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Clock Adjustment
CLOCK ADJ
(12 hour system)
Default : Not adjusted. “12:00”
Press [BAND] to set.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
<Display Setting>
[BAND] (Set)
S
H
Notes:
¡Operations except setting should be performed after
returning to the mode display.
26
¡If no keys have been pressed for more than 15 sec-
onds, the display returns to the previous one after
changing to the menu display.
[SEL] (Menu)
[}] [{]
(Select/Adjust)
[]] [[]
(Select/Adjust)
¡Press [DISP] to return to the regular mode.
[DISP] (Return)
[TUNE[] or [TUNE]] / [[] or []] to change.
Press [BAND] to set.
: Display showing a cube that continues to
change
: Display showing a globe that continues to
change
: Display showing a bird flapping its wings
A
B
C
D
E
: Display showing the image of a circuit
: Display showing a flower or doll pattern
: Standard spectrum analyzer display (15 band)
STD
Note: Switch the screen display to have the Spectrum Analyzer Display. (apage 13)
[TUNE[] / [[] : Level up
[TUNE]] / []] : Level down
Press [BAND] to set.
Press [BAND] to switch on or off in turn.
Clock Display
: Clock display ON
: Clock display OFF
ON
OFF
Hour / Minute Switch
Hour / Minute Adjustment
[TUNE]] / []] : The hour display
[P•SET}] / [}] : Put forward hour/minute.
[TUNE[] / [[] : The minute display
[P•SET{] / [{] : Put back hour/minute.
Press [BAND] to set.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
(continued)
Various Settings
[BAND] (Set)
OPEN
P
IS
P
D
FUNCTION Menu Display
CQ-SRX7000U
·M
D
PWR
SPC
REMOTE
SET/TM
SOURCE
27
D
BAN
DIM
P-SET
·W
SUB
VOL
TUNE
TRACK
ITH FULL DOT MATRIX DISPLAY
MENU
SD/CD RECEIVER W
DISC
[DISP]
(Return)
MUTE
[MENU]
(Menu)
[P•SET}] [P•SET{] (Select)
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Mute/ATT (Attenuator)
Decreasing range by pressing [MUTE] button
can be selected.
MUTE KEY
Default : Mute
Navi Mute
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Allows you to mute the current source while
your navigation system provides voice guid-
ance. (not available yet)
Press [MENU] / [SEL] to
select FUNCTION.
EXT. MUTE
Default : Lv 0
Preparation : Connect the Navi Mute lead.
Current Source
AUDIO
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Excluding AUX-IN from
Source Selection
PICTURE
AUX-IN
Default : ON
FUNCTION
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Button Operation Sound
(Signal/beep sound)
BEEP
Default : ON
Press [P•SET}] or
[P•SET{] / [}] or [{]
to select
Security Function
Default : ON
S·LED
36
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
<Function Setting>
[BAND] (Set)
S
H
Notes:
¡Operations except setting should be performed after
returning to the mode display.
28
¡If no keys have been pressed for more than 15 sec-
onds, the display returns to the previous one after
changing to the menu display.
[SEL] (Menu)
[}] [{]
(Select)
¡Press [DISP] to return to the regular mode.
[DISP] (Return)
Press [BAND] to switch between mute or attenuator in turn.
: No sound
MUTE
ATT
: Decrease to 1/10
Press [BAND] to change the volume level of the sound source as shown.
: No sound
Lv 0
Lv 1
Lv 2
OFF
Note: The setting state of the Navi Mute is displayed when the voice
guidance is used (except when the setting state is OFF).
: Decrease to 1/30
: Decrease to 1/10
: Unchanged
Press [BAND] to activate the function or inactivate it in turn.
: External input (AUX-IN) is selectable as a source.
: External input (AUX-IN) is not selectable as a source.
ON
OFF
With AUX-IN set to OFF, AUX-IN will not be selected when [SOURCE] is pressed.(apage 12 about source
selection)
Press [BAND] to switch the beep on or off in turn.
: Operation sound is heard when pressing buttons.
: No sound
ON
OFF
Press [BAND] to activate the function or inactivate
it in turn.
Security Function
When the key in the ignition is turned OFF.
¡Security message will be displayed.
¡The panel removal and SD Memory Card removal
alarm will be active.
: Security function is active.
: Security function is inactive.
ON
OFF
When the front panel is removed.
¡The security indicator blinks. (apage 45)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
About SD
29
The SD player in this unit is only for playing.
The player supports only SD Memory Cards on which SD audio-formatted-sound-
data is written in AAC or MP3 method. (You can neither format the card nor
record / delete data on the card.)
Because Panasonic SD Audio Player (SV-SD75) are equipped with a SD Memory Card
and other items that are required to write music data on the card except a personal com-
puter, you can use those.
(Accessories supplied to SV-SD75)
¡SD Memory Card, 64 MB
¡Software* “RealJukebox for Panasonic” (in the CD-ROM,
Panasonic Media Manager V2)
¡USB reader/writer device
Refer to the operating instructions for Panasonic SD Audio Player and accessories
described above and the online help, in addition.
* This is a software that can copy data from a music CD or MP3 to an SD Memory Card via the hard disc.
This software allows you to change or input a list name, a title, artist and so on.
Notes:
¡Use the only SD Memory Cards that are supplied with Panasonic SD Audio Player or are specified in the operating
instructions for Panasonic SD Audio Player. Other SD Memory Cards that are not recommended may not be used.
¡Use the software, what is called “RealJukebox for Panasonic”, supplied with Panasonic SD Audio Player for writing
music data on a card.
This unit may not read music data that are written by the use of a software other than RealJukebox for Panasonic.
Written Data
¡Music data that are not supported by SD Audio Standard V1.0 may not be readable.
¡We do not compensate users for damaged or deleted data due to the defects of this unit or a personal computer, the
electrostatic influence or the electrical noise influence on a SD Memory Card, and etc. Panasonic assumes no responsi-
bility for problems resulting from the damaged or deleted data.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
❏ Terms for SD
AAC
SD audio player
30
is an abbreviation for “Advanced Audio Coding”. This is
one of the audio compression methods and applied in the
picture compression standard, “MPEG-2” or “MPEG-4”.
AAC can reproduce higher tones compared to MP3 by
covering a wide sound range.
is an exclusive player for SD Memory Cards that received
data from CDs or digital contents delivered through the
internet in the future.
Play list
has the following two types.
¡Default play list
MP3
is an abbreviation for “MPEG-1 Audio Layer-3”. This is
one of the audio compression methods and applied in the
picture compression standard, “MPEG-1”.
is an all-track list i.e. a mass of all music data recorded in
a personal computer or saved in a SD Memory Card (up
to 999 tracks).
¡Play list
SD Memory Card
is a grouped list. You can make a play list by selecting
your favorite music (up to 99 tracks) or you can make it
from the list saved in an SD Memory Card.
SD is an abbreviation for “Secure Digital”. This is a
recording medium that features a function of protecting
copyright, compact, lightweight, large capacity and high-
speed writing. This medium can record pictures, music,
and so on.
Music list
is a list which shows tracks in the SD Memory Card or in
the play list (when play list is played by this unit).
Be sure to use a SD Memory Card that has less than
64 megabytes of memory.
The following cards can not be accepted.
¡Memory card except SD (such as multimedia card)
¡Card that has data compressed by other than AAC
or MP3
¡Card that has other than SD audio data
¡Card that has not been formatted (unformatted
card)
¡Card that contains no data (blank card)
Check Out
Record
Play List
A
B
Play List
C
D
E
Play List
Default
B
E
B
E
Play List
Default
Play List C
D
B
A
E
All music data recorded
in a personal computer
All music data are checked
out in an SD memory card
39
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
Installation Guide
WARNING
31
This installation information is designed for experienced installers
and is not intended for non-technical individuals. It does not contain
warnings or cautions of potential dangers involved in attempting to
install this product.
Any attempt to install this product in a motor car by anyone other
than qualified installer could cause damage to the electrical system
and could result in serious personal injury or death.
❏ Overview
❏ Installation Hardware
This product should be installed by a professional.
However, if you plan to install this product yourself,
your first step is to decide where to install it. The
instructions in these pages will guide you through
the remaining steps: (Please refer to the “WARN-
ING” statement above).
No.
Item
Q’ty
Diagram
q
Mounting Collar
1
w
e
Mounting Bolt (5 mmø)
1
1
Power Connector
¡Identify and label the car wires.
¡Connect the car wires to the wires of the power
connector.
¡Install the unit in the dashboard.
¡Check the operation of the unit.
r
t
Removable Face Plate Case
Trim Plate
1
1
If you encounter problems, please consult your
nearest professional installer.
y
Rear support strap
1
u
i
Tapping screw
Hex. Nut
1
1
Caution: This unit operates with a 12 volt DC nega-
tive ground auto battery system only. Do not attempt
to use it in any other system. Doing so could cause
serious damage.
❏ Required Tools
You’ll need a screwdriver, a 1.5 volt AA battery, and
the following:
Before you begin installation, look for the items on
the right which are packed with your unit.
12 V DC
Test Bulb
Electrical
Tape
Side-Cut
Pliers
¡Warranty Card …… Fill this out promptly.
¡Panasonic Servicenter for Service Directory
…… Keep for future reference in case the product
needs servicing.
¡Installation Hardware …… Needed for in-dash
installation
40
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
Battery Lead
❏ Dashboard Specifications
S
H
If your stereo unit has a yellow lead, you will need to
locate the car's battery lead. Otherwise you may
ignore this procedure. (The yellow battery lead pro-
vides continuous power to maintain a clock, memory
storage, or other function.)
Thickness
MIN. 3/16" (4.75 mm)
MAX. 7/32" (5.56 mm)
32
2-3/32" (53 mm)
7-5/32" (182 mm)
If your car has a radio or is pre-wired for one:
With the ignition and headlights off, identify the car
battery lead by grounding one lead of the test bulb
to the chassis and checking the remaining exposed
wires from the cut radio connector plug.
❏ Identify All Leads
The first step in installation is to identify all the car
wires you’ll use when hooking up your sound sys-
tem.
If your car is not wired for an audio unit :
Go to the fuse block and find the fuse port for the
battery, usually marked BAT.
Speakers
As you identify each wire, we suggest that you label
it using masking tape and a permanent marker. This
will help avoid confusion when making connections
later.
Identify the car speaker leads. There will be two
leads for each speaker, usually color coded.
A handy way to identify the speaker leads and the
speaker they connect with is to test the leads using
a 1.5 V AA battery as follows.
Hold one lead against one pole of the battery and
stroke the other lead across the other pole. You will
hear a scraping sound in a speaker if you are hold-
ing a speaker lead.
Note: Do not connect the power connector to the
stereo unit until you have made all connections. If
there are no plastic caps on the stereo hooking
wires, insulate all exposed leads with electrical tape
until you are ready to use them. Identify the leads in
the following order.
If not, keep testing different lead combinations until
you have located all the speaker leads. When you
label them, include the speaker location for each.
Power Lead
If your car has a radio or is pre-wired for one :
Cut the connector wires one at a time from the plug
(leaving the leads as long as possible) so that you
can work with individual leads.
Antenna Motor
If your car is equipped with an automatic power
antenna, identify the car motor antenna lead by con-
necting one bulb tester lead to the car battery lead
and touching the remaining exposed wires from the
cut radio connector plug one at a time. You will hear
the antenna motor activate when you touch the cor-
rect wire.
Turn the ignition on to the accessory position, and
ground one lead of the test bulb to the chassis.
Antenna
The antenna lead is a thick, black wire with a metal
plug at the end.
Touch the other lead of the test bulb to each of the
exposed wires from the cut radio connector plug.
Touch one wire at a time until you find the outlet that
causes the test bulb to light.
❏ Connect All Leads
Now that you have identified all the wires in the car,
you're ready to begin connecting them to the stereo
unit wires. The connection diagram (a Page 46)
shows the proper connections and color coding of
the leads.
Now turn the ignition off and then on. If the bulb also
turns off and on, that outlet is the car power lead.
If your car is not wired for an audio unit :
We strongly recommend that you test the unit
before making a final installation.
Go to the fuse block and find the fuse port for radio
(RADIO), accessory (ACC), or ignition (IGN).
41
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
(continued)
Installation Guide
You can set the unit on the floor and make tempo-
rary connections to test the unit. Use electrical tape
to cover all exposed wires.
the antenna/antenna extension cord. Read the oper-
ating and installation instructions of any equipment
you will connect to this unit.
33
Important: Connect the red power lead last, after
Power
you have made and insulated all other connections.
Connect the red power lead to the correct car radio
wire or to the appropriate fuse port on the fuse
block.
Ground
If the stereo unit functions properly with all these
connections made, disconnect the wires and pro-
ceed to the final installation.
Connect the black ground lead of the power connec-
tor to the metal car chassis.
Speakers
❏ Final Installation
Connect the speaker wires. See the wiring diagram
for the proper hookups. Follow the diagram carefully
to avoid damaging the speakers and the stereo unit.
Lead Connections
Connect all wires, making sure that each connection
is insulated and secure. Bundle all loose wires and
fasten them with tape so they will not fall down later.
Now insert the stereo unit into the mounting collar.
The speaker used must be able to handle more than
45 W of audio power. If using an optional audio
power, the speakers should be able to handle the
maximum amplifier output power. Speakers with low
input ratings can be damaged.
Congratulations! After making a few final checks,
you’re ready to enjoy your new auto stereo system.
❏ Final Checks
Speaker impedance should measure 4 - 8 Ω, which
is typically marked on most speakers. Lower or
higher impedance speakers will affect output and
can cause both speaker and stereo unit damage.
1. Make sure that all wires are properly connect-
ed and insulated.
2. Make sure that the stereo unit is securely held
in the mounting collar.
3. Turn on the ignition to check the unit for prop-
er operation.
Caution: Never ground the speaker cords. For
example, do not use a chassis ground system or a
three-wire speaker common system. Each speaker
must be connected separately using parallel insulat-
ed wires. If in doubt about how your car's speakers
are wired, please consult with your nearest profes-
sional installer.
If you have difficulties, consult your nearest autho-
rized professional installer for assistance.
❏ Precautions
¡Disconnect the cable from the negative
battery
terminal (see caution below).
Motor Antenna
Connect the car motor antenna lead to the blue
motor antenna relay control lead.
¡Unit should be installed in a horizontal position
with the front end up at a convenient angle, but
not more than 30°.
Battery
Connect the yellow battery lead to the correct radio
wire or to the battery fuse port on the fuse block.
Antenna
less than 30°
Connect the antenna by plugging the antenna lead
into the antenna receptacle.
Equipment
Caution : Do not disconnect the battery termi-
nals of a car with trip or navigational computer
since all user settings stored in memory will be
lost. Instead take extra care with installing the
unit to prevent shorts.
Connect any optional equipment such as an amplifi-
er, according to the instructions furnished with the
equipment. Leave about 12 inches (30 cm) of dis-
tance between the speaker leads/amplifier unit and
42
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
¡We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
¡When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your
hands and fingers.
34
❏ Installation Procedures
First, complete the electrical con-
nections, and then check them for
correctness. (apage 46).
Insert Mounting Collar q into the dashboard,
and bend the mounting tabs out with a screw-
driver.
1
Lock Lever
e Power Connector
Mounting Tabs
w Mounting Bolt
Secure the rear of the unit.
After fixing Mounting Bolt w and Power Connector
2
3
4
e, fix the rear of the unit to the car body by either
method (a) or (b) shown below.
Insert Trim Plate t.
Make sure that the lock lever is
flush with the mounting collar
(not projecting outward).
After installation
reconnect the nega-
tive
nal.
battery termi-
Lock Lever
(b) Using the Rubber Cushion (Option)
(a) Using the Rear Support Strap y
Rear Support Bracket
(Provided on the car)
Fire Wall of Car
3 mmø
uTapping Screw
Rubber Cushion
(Option)
iHex. Nut
yRear Support Strap
wMounting Bolt
qMounting Collar
wMounting Bolt
qMounting Collar
43
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
(continued)
Installation Guide
S
H
To Remove the Unit
Switch off the power of the unit.
35
Remove the removable face plate.
1
1
Open
Contact
q Press [OPEN]. The removable face plate will
be opened.
w Push the face plate to either the right or left.
e Pull it out toward you.
OPEN
DISP
3
Pull out
D·M
PWR
SOURCE
2
Push
DIM
Remove the Trim Plate t with a screwdriver.
2
t Trim Plate
Screwdriver
1
2
Pull out the unit while pushing down the lock
lever with a screwdriver.
3
Lock Lever
Screwdriver
Remove the unit pulling with both hands.
4
Lock Lever
44
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
Anti-Theft System
This unit is equipped with a removable face plate. Removing
this face plate makes the radio totally inoperable. The security
indicator will blink.
S
H
r Removable Face Plate Case
36
Place Removable Face Plate
into Case
q Switch off the power of the unit.
w Remove the removable face plate.
(aPage 44)
e Gently press the bottom of the case and open the cover.
Place the face plate into the case and take it with you
when you leave the car.
Install Removable Face Plate
Contact
q Fit the face plate with its right or left hole on one of the
pins provided on the main unit.
w Fit the other hold on the other pin applying slight pres-
sure.
e Move the face plate up and down a few times to make
sure it is secure. Then close the front panel and press
down the right side of the face plate until it clicks into
plate.
3
1
2
Security Indicator
The security indicator blinks when the removable face plate is
removed from the unit.
Activate the security function in the FUNCTION menu display.
(aPage 36)
Panel Removal Alarm
Security Indicator
This alarm sounds to warn you not to forget to remove the
panel before leaving your car. This function is activated when
the security indicator is on.
Cautions:
¡This face plate is not waterproof. Do not expose it to water or excessive moisture.
¡Do not remove the face plate while driving your car.
¡Do not place the face plate on the dashboard or nearby areas where the temperature rises to high levels.
¡Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical contacts.
¡If dirt or other foreign substances get on the contacts, wipe them off with clean and dry cloth.
¡To avoid damaging the front panel, do not push it down or place objects on it while it is open.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
Electrical Connections
Cautions:
S
H
¡This product is designed to operate off a 12 volt, negative ground battery system.
¡To prevent damage to the unit, be sure to follow the connection diagram bellow.
¡Remove approx. 1/4” (5 mm) of protective covering from the ends of the leads before connecting.
¡Do not insert the power connector into the unit until the wiring is completed.
¡Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all cables and keep
cable terminals free from touching any metal parts.
37
¡Remember, if your car has a drive computer or a navigation computer, the data of its memory may be erased when
the battery terminals are disconnected.
Supplied hardware
SD/CD Receiver
CQ-SRX7000U
(Rear)
No.
Item
Q’ty
e
Power Connector
1
Antenna
❏ Wiring Diagram
CD Changer
Control
Connector
Navi Mute Lead
e Power Connector
NAVI MUTE
Connect to the Navi Mute Lead of the Panasonic
car navigation system (not available yet).
Note: Insulate the Navi Mute Lead with vinyl tape
when you do not connect it.
(Orange)
ANT-CONT MAX 0.1A
ILLUMINATION
Antenna Control Cord
To the auto antenna control power
cord of the car
(Blue)
Illumination Lead
To the power line connected to
the side marker lights of the car
(Orange / white stripe)
Dual CD Changer Control Lead (not used)
Note: Insulate the Dual CD Changer Control
Lead with vinyl tape.
TWIN CD·C-CONT
(Brown / white stripe)
(Blue / white stripe)
External Amplifier Control Power Lead
AMP-CONT MAX 0.1A
To an external amplifier
ACC Power Lead
ACC
To ACC power, +12V DC
(Red)
Resistor (1kΩ)
Battery Lead
BATTERY 10A
To the car battery, continuous
+12V DC
(Yellow)
Fuse (10A)
Ground Lead
To a clean, bare metallic part of
the car chassis
(Black)
Note: If your car does not have a power line connected to the side marker lights of the car, leave the illumination lead disconnected.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
38
(R) (Red)
CH.C-IN
CENTER
CD Changer Input
Cord
(L) (White)
(L)(White)
Preout Cord (Center)
(R) (Red)
AUX Input Cord
AUX-IN
FRONT
REAR
(L) (White)
(R) (Red)
Preout Cord (Front)
Preout Cord (Rear)
Sub-Woofer Cord
(L) (White)
(R) (Red)
(L) (White)
(Red)
S·W-OUT
(White)
(White)
(Left)
Front Speaker Lead (Left)
FRONT L
FRONT R
(White / black stripe)
(Gray)
To Front Speaker
(Right)
Front Speaker Lead (Right)
(Gray / black stripe)
(Green)
(Green / black stripe)
(Violet)
Rear Speaker Lead (Left)
(Left)
REAR L
REAR R
To Rear Speaker
Rear Speaker Lead (Right)
(Right)
(Violet / black stripe)
47
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
(continued)
Electrical Connections
S
H
System Upgrade Example
Combination : CD changer (CX-DP88U)
39
Note : For wiring, carefully read the operating instructions for the devices connected.
Ground Lead
CD Changer
CX-DP88U
(R) (Red)
CD Changer Input Cord
CH.C-IN
Extension Cord
(Supplied for CX-DP88U)
(L) (White)
RCA Cord
Battery Lead
BATTERY
Sub-Woofer Cord
S·W-OUT
(Fuse 3A)
SD/CD Receiver
CQ-SRX7000U
(Rear)
DIN Cord
(White)
(Red)
CD Changer
Control Connector
e Power Connector
Stereo
Power Amplifier
Sub-Woofer
Speakers
48
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
Troubleshooting
S
H
Preliminary Steps
Cautions:
¡Do not use the unit if it malfunctions or is
something is wrong.
Check and take steps as described in the tables below.
40
¡Do not use the unit in an irregular condition,
for example, without sound, or with smoke
or foul smell, which can cause ignition or
electric shock. Immediately stop using the
unit and call the store where you purchased
it.
If You Suspect Something Wrong
Immediately switch power off.
Disconnect the power cable and check that there is neither smoke
nor heat from the unit before asking for repairs. Never try to repair
the unit yourself because it is dangerous to do so.
I Common
Problem
Possible cause / Possible solution
Car’s engine switch is not on.
aTurn your car’s ignition switch to ACC or ON.
Cables are not correctly connected.
aConnect cables correctly.
Battery cable is not correctly connected.
aConnect the battery cable to the terminal that is always live.
No power
Accessory cable is not correctly connected.
aConnect the accessory cable to your car's ACC source.
Grounding wire is not correctly connected.
aConnect the grounding wire to a metal part of your car.
Fuse is burnt.
a
Call the store where you purchased the unit, or your nearest Panasonic
Servicenter (see the attached sheet) and ask for fuse replacement.
Mute is set to ON.
aSet it to OFF.
Cables are not correctly connected.
aConnect cables correctly.
No sound
Condensation (dew)
aWait for a while before use.
The display is set to OFF.
Only sound, no display
Noise
aPress [DISP] to change the display.
A mobile phone is used near the unit.
aKeep the mobile phone away from the unit.
Menu mode is displayed.
aPress [DISP] to return to the regular mode.
Buttons unusable
(each source operation)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
(continued)
Troubleshooting
I Radio
Problem
Possible cause / Possible solution
41
Station is too far, or signals are too weak.
aSelect other stations of higher signal level.
Much noise in FM
stereo and monaural
broadcasts
The radio antenna is not extended enough.
aExtend the radio antenna enough.
Battery cable is not correctly connected.
aConnect the battery cable to the terminal that is always live.
Preset station is reset.
I CD
Problem
Possible cause / Possible solution
CD is upside down.
aPlace CD in the correct direction with the label side up.
CD is in the CD com-
partment but no sound
is made, or CD is eject-
ed automatically.
CD is dirty.
aClean CD, referring to the section on Notes on CD.
CD-R on which sound is not recorded is used.
aUse a CD-R disc on which sound is recorded.
CD sound skips, tone
quality is low.
CD is dirty.
aClean CD, referring to the section on Notes on CD.
Mounting angle is over 30 degrees.
aAdjust mounting angle to less than 30 degrees.
Sound skip due to
vibration
Instable mounting.
aMount the unit securely with the mounting parts, referring to the section
on Installation.
¡CD is defective.
¡Mechanical trouble.
CD is not ejected.
aOpen the panel and press [uCD]. If failure persists, press the reset
switch. If normal operation is not restored, call the store where you pur-
chased the unit or the nearest Panasonic Servicenter to ask for repairs.
I SD
Problem
Possible cause / Possible solution
An SD Memory Card is loaded upside down or in the wrong direction.
aLoad the SD Memory Card in a correctly.
SD Memory Card is
loaded but no sound.
The SD Memory Card has no sound.
aLoad an SD Memory Card on which sound is recorded.
Recorded music data is not applied for SD Audio Standard V1.0.
aSelect other track (or play list).
"0'00" is displayed and
no sound.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
I Sound Setting
Problem
Possible cause / Possible solution
42
Left and right balance, or front and rear balance is off on one side.
aAdjust BAL/FAD as appropriate.
No sound from left,
right, front, or rear
speaker
Cables are not correctly connected.
aConnect the cables correctly.
Left and right sounds
are reversed in stereo
listening.
The right speaker wire is connected to the left speaker and the left speaker wire
to the right speaker.
aConnect the speaker wires to the correct one.
No sound from center
speaker (Option)
Center speaker volume is set to – ∞.
aSet center speaker volume to other than – ∞.
Only bass or monaural
sound from rear speaker
SBC-SW is set to ON.
aSet SBC-SW to OFF.
SBC-SW is set to ON and DDBC volume to – ∞.
aSet DDBC volume to other than – ∞.
No sound from rear
speaker preout (rear)
DDBC volume is set to – ∞.
aSet DDBC volume to other than – ∞.
No sound from the pre-
out <sub-woofer out-
put>
I Remote Control
Problem
Possible cause / Possible solution
Battery polarities (+) (–) are reversed.
aInsert the batteries correctly.
Wrong batteries
aCheck the batteries.
Buttons are invalid for
operation.
Batteries have run down.
aReplace the batteries.
Remote control is in the wrong direction.
aDirect the remote controller at REMOTE (sensor) on the panel.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
(continued)
Troubleshooting
Error Display Messages
S
H
I CD
43
Display
Possible cause / Possible solution
Disc is dirty, or is upside down.
Disc has scratches.
No operation by some cause
After 5 seconds
aOpen the panel and press [uCD].
¡Check disc.
¡Load the disc again.
After 5 seconds
Return to previous mode
I Changer
Display
Possible cause / Possible solution
Disc is dirty, or is upside down.
Disc has scratches.
aPress [u] to eject the magazine.
¡Check disc.
¡Load the disc again.
To next disc automatically
No operation by some cause
aPress [u] to eject the magazine. If failure persists, press the reset
switch. If normal operation is not restored, call the store where you
purchased the unit or the nearest Panasonic Servicenter to ask for
repairs.
Return to
previous mode
The display continues if the power is not turned off automatically.
No disc is in the CD changer (magazine).
aInsert discs into the changer (magazine).
Notes:
¡There may be cases where the disc numbers affected by an error are displayed before E1 and E2.
¡Displays and the steps to be taken for errors vary in part from changer to changer. For details, refer to the Operating
Instructions for the changer used.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
I SD
44
Display
Possible cause / Possible solution
When there is no music in a play list.
aSelect another play list and play it.
An error occurs.
aLoad the card again.
After 5 seconds
When the data is recorded by other than AAC compression method or MP3
compression method.
aPlay the track (or play list) which is recorded by AAC compression
method or MP3 compression method only.
When other than SD Memory Card is loaded
When there is no data in the card
When the card is unformatted
When the data is out of SD audio standard
When the card is formatted illegally
When the data are locked in the card
Attestation error
The music data or folders in the SD Memory Card have been moved,
changed their name or deleted by using Windows Explorer, etc.
After 5 seconds
aOpen the panel and eject the SD Memory Card.
¡Check the card and data.
¡Load the card again.
For some reason, the unit can not read the data.
Notes: Refer to the operating instructions and online help for the software "RealJukebox for Panasonic".
53
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
(continued)
Troubleshooting
Maintenance
S
H
Your product is designed and manufactured to ensure a minimum of maintenance. Use a dry soft cloth for routine exterior
cleaning. Never use benzine, thinner or other solvents.
45
Product Servicing
If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest authorized
Panasonic Servicenter. The product should be serviced only by a qualified technician.
Replacing the Fuse
Use fuses of the same specified rating (10 amps). Using different substitutes, or fuses with a higher rating, or connecting
the product directly without a fuse, could cause a fire or damage to the stereo unit.
If the replacement fuse fails, contact your nearest Panasonic Servicenter for service.
Reset Switch
Reset switch
Insert a hard slender stick into the hole and push the switch.
¡The unit returns to the default state when the trouble is reset.
Remember, the data and settings stored in the memory are
deleted.
Important
Push the switch only when the unit fails to operate with any but-
tons.
If the panel cannot be opened, or if the unit fails to return to nor-
mal condition, call the nearest service station and ask for repairs.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
Maintenance
S
H
Cleaning this unit
Caution on cleaning
Use a dry, soft cloth to wipe.
Never use solvents such as benzine, thinner as they may
mar the surface of the unit.
46
Notes on CD
ONLY USE DISCS CARRYING THE LABEL
How to hold the CD
Label side
¡Do not touch the underside of the disc.
¡Do not make scratches on the disc.
¡Do not bend disc.
¡When not in use, keep CD in the case.
Do not use irregularly shaped CDs.
Do not leave discs in the following places:
¡Direct sunlight
¡Near car heaters
¡Dirty, dusty and damp areas
¡Seats and dashboards
Do not use irregularly shaped CDs.
<Wrong>
<Right>
Disc Cleaning
Use a dry, soft cloth to wipe from the center outward.
Caution on New Discs
A new disc may have rough edges on its inner and outer
perimeter. These may cause malfunction.
Rough edge
Remove the rough edges using a pencil, etc.
Notes on CD-R Disc
A playable CD-R is only a CD-R disc on which sound was recorded.
¡Some recorded CD-R discs by using CD recorder are not playable because of their characteristic, or scratches or dirt on
the discs.
¡You can not play a CD-R disc that has not been finalized.
¡A CD-RW disc is not playable.
¡MP3 file, video CD, CD-ROM and CD-EX disc are not playable.
¡Be sure to observe the instructions of CD-R disc for handling it.
¡Do not apply a disc that has a label printed by a commercially available label printer.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
S
H
(continued)
Maintenance
Notes on SD Memory Card
47
Use SD Memory Cards on which music data were written by use of the software,
“RealJukebox for Panasonic”, and a personal computer that supports the software.
Cautions regarding handling
¡Keep the SD Memory Card out of the reach of children to prevent them from swallowing it.
¡Do not disassemble or alter a card.
¡Do not drop, moisten, or shock a card.
¡Do not bend a card.
¡Do not touch the metal part of a card with your hand or metallic material.
¡Do not take off a label. Do not stick a new label or seal on a card.
Do not use cracked or wrapped cards.
Cautions regarding custody
¡Be sure to keep a card in a case when the card is not used.
¡Do not leave a card in places where the temperature increases such as inside a car, a place in direct sunlight, near the
heat vent or near the heating appliance.
¡Do not leave a card in places where humidity is high, or a corrosive gas is generated.
¡Do not leave a card in a dusty place.
¡Be sure to remove a SD Memory Card from the unit if the unit is not used for a long time.
Cautions regarding stored data
¡Set the write-protect switch to “LOCK”. Unlock when recording or editing the
card.
¡When writing something in the memo space, use oil-based felt pen. A card
might be damaged or stored data in a card might be destroyed if a pencil or a
ballpoint are used.
Write-protect Switch
Memo Space
Rear
View
Panasonic will not accept responsibility for any data loss or loss directly or indirectly caused by data loss.
Specifications
General
Power Supply
: DC 12 V (11 V - 16 V), test voltage 14.4 V, negative ground
Current Consumption
Rated Output
: Less than 2.5 A (CD/SD mode, 0.5 W 4-speaker)
: 16 W x 4 ch (1 kHz, 1%, 4 Ω)
: 45 W x 4
Maximum Power Output
Compatible Speaker Impedance
External Input Impedance
External Input Sensitivity
Pre-Amp Output Voltage
Center Speaker Output (Pre-Out)
Pre-Amp Output Impedance
Sub-Woofer Output Voltage
Dimensions (W x H x D)
Weight
: 4 Ω
: 10 kΩ (AUX IN)
: Max. 2 V (AUX IN)
: 5 V
: 2 Vrms
: 60 Ω
: 5 V
: 7" x 1-15/16" x 6-1/8" (178 x 50 x 155 mm)
: 3 lbs. 5 oz (1.5 kg)
56
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
E
N
G
L
I
Specifications
(continued)
S
H
DSP
Number of Channels
Space mode
: 2 input channels, 6 output channels
: 7 modes
48
Equalizer Center Frequency
Variable Range of Equalizer
: 80, 160, 320, 640, 1.6 k, 4 k, 10 k (Hz)
: –12 to +12 dB (13 steps)
FM Stereo Radio
Frequency Range
: 87.9 - 107.9 MHz
: 11.0 dBf. (1.25 µV, 75 Ω)
: 15.2 dBf. (1.6 µV, 75 Ω)
: 30 Hz – 15 kHz ( 3 dB)
: 75 dB
: 42 dB (at 1 kHz)
: 75 dB
Usable Sensitivity
50 dB quieting sensitivity
Frequency Response
Alternate channel sensitivity
Stereo Separation
Image response ratio
IF response ratio
: 100 dB
Signal / noise ratio
: 70 dB
AM Radio
Frequency Range
Usable Sensitivity
: 530 kHz - 1,710 kHz
: 28 dB/µV (25 µV, S/N 20 dB)
CD Player
Sampling Frequency
DA Converter
Error Correction System
Pick-Up Type
: 8 times oversampling
: MASH•1 bit/4 DAC System
: Panasonic Super Decoding Algorithm
: Astigma 3-beam
Light Source
Wave Length
: Semiconductor Laser
: 780 nm
Frequency Response
Signal to Noise Ratio
Total Harmonic Distortion
Wow and Flutter
Channel Separation
: 5 Hz - 20 kHz ( 1 dB)
: 90 dB
: 0.01 % (1 kHz)
: Below measurable limits
: 70 dB
SD Player
Compression and decompression method : AAC/MP3
Channel
: Stereo/2 channels
: 20 Hz - 20 kHz ( 1 dB)
: 90 dB (IHF, A)
: 48k, 44.1k, 32k, 24k, 22.05k, 16k (Hz)
: 192, 160, 128, 112, 96, 80, 64, 48, 32, 16 (kbps)
Frequency Response
Signal to Noise Ratio
Sampling Frequency
Bit Rate
Above specifications comply with EIA standards.
Note : Specifications and the design are subject to modification without notice due to improvements in technology.
SD logo is a trademark.
¡
TM
Portions of this product are protected under copyright law and are provided under license by ARIS/SOLONA/4C.
RealJukebox is a trademark of RealNetworks, Inc.
Microsoft and its logo as well as Windows and Windows NT are registered trademarks of Microsoft Corporation of the
U.S. in both the United States and other countries.
The ™ and ® markds are not used to identify registered trademarks and trademarks in this operating instructions.
¡
¡
¡
¡
57
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-SRX7000U
Panasonic Consumer Electronics Panasonic Sales Company.
Panasonic Canada Inc.
5770 Ambler Drive,
Mississauga, Ontario
L4W 2T3
Company, Division of Matsushita
Electric Corporation of America
One Panasonic Way, Secaucus,
New Jersey 07094
Division of Matsushita Electric of
Puerto Rico, Inc. (“PSC”)
Ave. 65 de Infanteria, Km. 9.5
Puerto Rico 00985
YEFM283664 B0201-0
Printed in Japan
Imprimé à Japon
Impreso en Japón
Download from Www.Somanuals.com. All Manuals Search And Download.
|