SHIFT_individuality
Download from Www.Somanuals.com. All Manuals Search And Download.
LOW TIRE PRESSURE WARNING
LIGHT
INSTRUMENT BRIGHTNESS
CONTROL*
VEHICLE DYNAMIC CONTROL (VDC)
OFF SWITCH
AUDIO AND NAVIGATION
SYSTEM
VEHICLE INFORMATION DISPLAY
WINDSHIELD WIPER/WASHER
SWITCH
INTELLIGENT KEY PORT
AUTOMATIC CLIMATE CONTROL
TWIN TRIP ODOMETER/TRIP
CHANGE BUTTON
STEERING WHEEL SWITCH FOR AUDIO
CONTROL/BLUETOOTHா
STEERING WHEEL TILT AND
TELESCOPIC ADJUSTMENT*
AUXILIARY INPUT JACK*
(if so equipped)
HEADLIGHT AND TURN SIGNAL
CONTROL
CRUISE CONTROL
HOOD RELEASE*
TRUNK LID OPENER
FRONT PASSENGER AIR
BAG STATUS LIGHT
*See your Owner’s Manual for more information.
Download from Www.Somanuals.com. All Manuals Search And Download.
NISSAN INTELLIGENT KEY™
The NISSAN Intelligent Key™ system allows you to lock or unlock
your vehicle, open your trunk and start the engine.
NOTE: It is important to make sure the Intelligent Key is with you
(that is, in your pocket or purse).
Ⅲ
The operating range of the door and trunk lock/unlock func-
tion is approximately 31 in (0.8 m).
Ⅲ
Locking the vehicle - Push any door handle Request Switch
(if so equipped)
once.
Ⅲ
Unlocking the vehicle - Push any door handle Request
Switch (if so equipped) once. The corresponding
door will unlock. Push the door handle Request
Switch
unlock.
again within 1 minute; all other doors will
OPENING THE TRUNK
Ⅲ
Ⅲ
Ⅲ
To open the trunk using the Request Switch (if so equipped),
your Intelligent Key must be with you.
Push the Request/Release Switch (if so equipped)
der the trunk handle.
un-
Lift up on the trunk lid to fully open the trunk.
STARTING THE ENGINE
Ⅲ
Depress the brake pedal (CVT) or clutch pedal (MT).
Ⅲ
Push the ignition switch to start the engine.
TURNING THE ENGINE OFF
Ⅲ
Shift the shift selector to the P (Park) position (CVT) or to
the N (Neutral) position (manual transmission) and apply the
parking brake.
Ⅲ
Push the ignition switch to turn the engine off.
NISSAN INTELLIGENT KEY™ BATTERY DISCHARGE
Ⅲ
If the battery of the Intelligent Key is almost discharged, the
guide light of the Intelligent Key port blinks and the Intelli-
gent Key insertion indicator is displayed in the vehicle
information display.
Ⅲ
To start the engine under these circumstances, insert the
Intelligent Key into the key port in the direction indicated
until it latches into place.
Ⅲ
Ⅲ
To remove the Intelligent Key from the port, push the ignition
switch to turn the engine off and pull the Intelligent Key out of the port.
The Intelligent Key port does not charge the Intelligent Key battery. If you see the low
battery indicator, replace the battery in the Intelligent Key.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC DOOR LOCKS
Ⅲ
All doors lock automatically when the vehicle speed reaches 15 MPH (24 km/h).
All doors unlock automatically when the ignition is placed in the OFF position.
Ⅲ
The automatic lock and unlock functions can be deactivated or activated inde-
pendently of each other. To deactivate or activate the automatic door lock or unlock
system, perform the following procedure:
1. Close all doors.
2. Place the ignition switch in the ON position.
3. Do one of the following within 20 seconds of performing Step #2:
● To change AUTO UNLOCK settings: push and hold the power door lock switch to
the
position (UNLOCK) for more than 5 seconds.
● To change AUTO LOCK settings: push and hold the power door lock switch to
the position (LOCK) for more than 5 seconds.
4. When activated, the hazard indicator will flash twice. When deactivated, the hazard
indicator will flash once.
5. The ignition switch must be placed in the OFF and ON position again between each
setting change.
WINDSHIELD WIPER/WASHER SWITCH
Ⅲ
The ignition switch must be in the ON position to
activate the windshield wipers.
Ⅲ
Move the lever to the following positions to oper-
ate the windshield wipers:
Intermittent (INT) – Front wipers operate
intermittently and can be further adjusted by
twisting the time control ring
.
Low Speed (LO) – Continuous low-speed
operation of front wipers.
High Speed (HI) – Continuous high-speed
operation of front wipers.
Mist (MIST) – Lift the lever up for one sweep of the front wipers.
Ⅲ
Pull the lever toward you to activate front washer fluid and several sweeps of the wipers.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HEADLIGHT AND TURN SIGNAL CONTROL
TO ACTIVATE THE AUTOLIGHT SYSTEM (if so
equipped):
Turn the headlight control switch
to the AUTO position
to activate the autolight system. The autolight system can:
Ⅲ
Ⅲ
Ⅲ
Turn the headlights on automatically when it is dark.
Turn the headlights off automatically when it is light.
Keep the headlights on for 45 seconds after you turn the ignition switch to OFF and all
doors are closed.
TO DEACTIVATE THE AUTOLIGHT SYSTEM:
Ⅲ
Turn the headlight control switch
to the OFF ,
or
position.
HEADLIGHT CONTROL SWITCH
Ⅲ
Turn the headlight control switch
to the
position to turn on the front parking,
position to turn on the headlights. All
tail, license plate and instrument panel lights.
Ⅲ
Turn the headlight control switch
other lights remain on.
to the
FOG LIGHT OPERATION (if so equipped)
NOTE: The headlights must be on and the low beams
operate.
selected for the fog lights to
Ⅲ
Ⅲ
Turn the switch (inside collar)
Turn the switch (inside collar)
to the
position to turn on the fog lights.
to the OFF position to turn off the fog lights.
HIGH BEAM
Ⅲ
Push the headlight control switch forward
select the high beam function. The blue
to
indica-
tor light illuminates. Pull the headlight switch back to
the original position to select the low beam. The
blue
indicator light goes off.
Ⅲ
Pull and release the headlight control switch
and off.
to flash the headlight high beams on
4
Download from Www.Somanuals.com. All Manuals Search And Download.
STEERING WHEEL SWITCHES FOR AUDIO CONTROL/
BLUETOOTHா (if so equipped)
Ⅲ
Press the SOURCE button to turn the radio sys-
tem on.
Ⅲ
To choose Preset A, B, C, CD or AUX, press
SOURCE repeatedly.
Ⅲ
The tune up or down
perform the following:
switch can be used to
● Push the switch for less than 1.5 seconds to
change to a preset station.
● Push and hold the switch for more than 1.5 seconds to seek to the next or previous
broadcasting radio station.
● Push the switch while playing a CD (if so equipped) for less than 1.5 seconds to
change tracks on the CD.
● If the vehicle is equipped with a CD changer, push and hold the switch for more
than 1.5 seconds to change between CDs.
Ⅲ
Push the + or – control switch to increase or decrease the volume.
CRUISE CONTROL
Ⅲ
To activate the cruise control, push the ON/OFF
switch. The indicator light in the Vehicle Informa-
tion Display will illuminate.
Ⅲ
To set cruising speed, accelerate the vehicle to
the desired speed, push the COAST/SET switch
and release it. The SET indicator light in the
Vehicle Information Display will illuminate.
Ⅲ
To reset at a faster cruising speed, push and hold
the ACCEL/RES switch. When the vehicle attains the speed you desire, release the
switch.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
To reset at a slower cruising speed, push and hold the COAST/SET switch. Release
the switch when the vehicle slows to the desired speed.
To cancel cruise control, push the CANCEL switch or tap the brake pedal. The SET
indicator light in the Vehicle Information Display will go out.
To resume a preset speed, push and release the ACCEL/RES switch. The vehicle
returns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h).
To turn off cruise control, push the ON/OFF switch. Both the CRUISE indicator light
and the SET indicator light in the Vehicle Information Display will go out.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL-FILLER CAP
Ⅲ
To tighten, turn the fuel-filler cap clockwise until ratcheting
clicks are heard. If the cap is not fully tightened, the service
engine soon light may illuminate.
Ⅲ
If
light illuminates because the fuel cap is loose or
missing, tighten or re-install the cap. The
turn off after a few driving trips.
should
AUTOMATIC CLIMATE CONTROL (if so equipped)
AUTO BUTTON
Ⅲ Press the AUTO button
. Turn the driver’s side temperature control dial
to
the desired temperature. This will allow the fan speed, air flow distribution and
temperature to be automatically maintained.
Ⅲ When AUTO is pressed, AUTO will illuminate. When DUAL
is pressed, DUAL
will illuminate.
Ⅲ To disable auto mode, press one of the air flow mode control buttons
fan speed control dial or press the front defroster control button
, turn the
.
DRIVER’S SIDE TEMPERATURE CONTROL DIAL
Turn the driver’s temperature control dial left for cold air or right for hot air.
DUAL BUTTON
Press the DUAL button to turn the passenger’s side temperature controls on or off. This
will allow the passenger’s side temperature to be adjusted independently from driver’s
side control.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PASSENGER’S SIDE TEMPERATURE CONTROL DIAL
Turn the passenger’s temperature control dial left for cold air or right for hot air; doing so
will activate dual mode.
AIR FLOW MODE CONTROL BUTTONS
Press the buttons to select the following air flow outlets:
Air flows from the center and side vents.
Air flows from the center, side, and foot vents.
Air flows mainly from the foot vents.
Air flows from the defroster and foot vents.
FAN SPEED CONTROL DIAL/OFF BUTTON
Turn the fan speed control dial to the left (slower) or right (faster) to manually control fan
speed. Press OFF to cancel fan speed operation and turn off climate control operation.
DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS
Ⅲ Press the defroster control button
to turn the system on. The A/C automatically
turns on when the defroster mode is selected.
Ⅲ Turn the driver’s side temperature control dial left or right to set the desired
temperature.
Ⅲ To set the defroster on high, turn the fan speed control dial all the way to the right.
DEFROSTING/DEFOGGING REAR WINDOW AND (if so equipped) OUTSIDE
HEATED MIRROR
Push the rear window defroster switch
on. Push the switch again to manually turn
the defroster off. This function automatically turns off in approximately 15 minutes.
A/C ON/OFF BUTTON
Press the A/C button to manually turn the A/C on or off.
AIR RECIRCULATION BUTTON
Ⅲ Press the air recirculation button
to recirculate air inside the vehicle.
again to turn air recirculation off.
Ⅲ Press the air recirculation button
Ⅲ The air recirculation mode can only be selected if the air flow control mode is in the
following positions: or
,
.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FM/AM/XMா* RADIO WITH CD CHANGER (if so equipped)
RADIO BUTTON
Pressing the RADIO button will change the band to either FM, AM, or XMா radio
stations.
SEEK/TRACK/CAT BUTTON
Ⅲ To scan quickly through each broadcasting station, press the SEEK/TRACK/CAT
button.
Ⅲ To skip from one track to another on a CD, press the SEEK/TRACK/CAT button.
TUNING AND AUDIO CONTROL KNOB (Bass, Treble, etc.)
Ⅲ To manually tune the radio, turn the TUNE·FOLDER knob. To adjust the Bass, Treble,
Balance and Fade, press the AUDIO knob until the desired mode appears in the
display. Then turn the TUNE·FOLDER knob to adjust to the desired level.
Ⅲ While playing an MP3 CD, turn the TUNE·FOLDER knob right or left to skip forward
or backward through the available folders. This function will only operate on an MP3
CD with multiple folders.
STATION AND CD SELECT BUTTONS
Ⅲ To store a station in a preset you must first select A, B, or C memory bank by pressing
the PRESET A·B·C button and tune to the desired FM, AM or XMா station. Then
press and hold the desired station select button for at least 2 seconds. When the
preset indicator illuminates, a beep will sound, indicating memorization is complete.
To retrieve a previously set station, select the memory bank where the preset was set,
then press the corresponding station select button.
Ⅲ While playing a CD, press one of the CD select buttons (1 - 6 ) to select a different
CD loaded into the CD changer.
PRESET A·B·C BUTTON
Press the PRESET A·B·C button until you reach the desired setting. The radio is
equipped with three separate banks, each with six station presets. You may store any
combination of FM, AM or XMா radio presets on each bank.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CD/AUX BUTTON
Ⅲ Press the CD/AUX button to play a CD loaded into the CD changer.
Ⅲ Press the CD/AUX button again to play a compatible device such as an MP3 player
when it is plugged into the auxiliary jack (cable not included).
NOTE: You may need to adjust the volume on any compatible device plugged into the
auxiliary jack to find the most desired sound level of the audio system.
EJECT BUTTON
Ⅲ EJECT A SINGLE DISC - Press
the
button for less than 1.5
seconds. Select the eject slot by
pressing one of the CD insert se-
lect buttons (1 - 6 ). The CD will
then eject.
Ⅲ EJECT ALL DISCS - Press and hold the
button for more than 1.5 seconds. The
CDs will be ejected one after another.
CD SELECT/LOAD BUTTONS
Ⅲ LOAD A SINGLE DISC - Press one of the CD insert select buttons (1 - 6 ) for less
than 1.5 seconds, wait for the CD slot door to open, then insert the CD.
Ⅲ LOAD UP TO 6 DISCS - Press and hold one of the CD insert select buttons (1 - 6)
for more than 1.5 seconds. Wait for the CD slot door to open before loading each
disc. The slot numbers (1-6) will illuminate on the display when CDs are loaded into
the changer
*XMா Satellite Radio is only available on vehicles equipped with optional XMா satellite
subscription service.
CLOCK SET/ADJUSTMENT
NAVIGATION SYSTEM ONLY (if so equipped)
Press the SETUP button, then touch the
“Clock” key to access the following clock
settings:
Ⅲ
On-screen Clock – When this item is
turned to ON, a clock is always dis-
played in the upper right corner of the
screen. The clock is automatically ad-
justed by the GPS system.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Clock Format – Choose either the 12-hour clock display or the 24-hour clock display.
Offset Adjust – Adjust the time by increasing or decreasing per minute.
Daylight Saving Time – Turn this item to ON for daylight savings time application.
Time Zone – Choose the time zone.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE INFORMATION DISPLAY
When the selection button
display on the screen:
is pressed, the following modes will
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Setting
Warnings (if there are any)
MPG (instant fuel economy)
MPG/MPH (average fuel economy and speed)
Time/Miles (elapsed time since last reset)
Range (average distance to empty)
Exterior temperature
SETTING MODE
When the setting mode
is selected, you are able to set reminders for alerts, mainte-
nance intervals or language displays.
Ⅲ
Ⅲ
Ⅲ
The ALERT mode allows you to set alerts notifying yourself of time to rest or icy traveling
conditions.
The MAINTENANCE mode allows you to set alerts for the reminding of maintenance
intervals for engine oil, oil filter, tires and others.
The DISPLAY mode allows you to change the unit of measurement (English or metric)
display.
TWIN TRIP ODOMETER
Ⅲ
The twin trip odometer records the distance of indi-
vidual trips.
Ⅲ
Press the button
to change the display as
follows: Trip A → Trip B → Trip A.
Ⅲ
Press and hold the button
trip odometer to zero.
for more than 1 second to reset the currently displayed
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTINUOUSLY VARIABLE TRANSMISSION (CVT) (if so equipped)
Ⅲ
The CVT does not produce a gear change sen-
sation like traditional automatic transmissions.
Ⅲ
The transmission in your vehicle requires a spe-
cial fluid available only at your NISSAN dealer.
No other fluid will meet the exact requirements
of the CVT.
MANUAL SHIFT MODE
Ⅲ
When the shift selector is shifted from D (Drive)
to the manual shift gate, the transmission enters
the manual shift mode.
Ⅲ
Ⅲ
In the manual shift mode, shift range is dis-
played on the position indicator in the meter.
When shifting up, move the shift selector to the
+ (up) side. (Shifts to higher range.)
Ⅲ
Ⅲ
When shifting down, move the shift selector to the - (down) side. (Shifts to lower range.)
In manual shift mode, the transmission automatically shifts down to M1 (first) before the
vehicle comes to a stop. When accelerating again, it is necessary to shift to the desired
range.
Ⅲ
When canceling the manual shift mode, return the shift selector to the D (Drive) position.
The transmission returns to the normal driving mode.
6-SPEED MANUAL TRANSMISSION (if so equipped)
LOCK OUT
Ⅲ
In 6-speed manual transmission equipped ve-
hicles, the shift selector is equipped with a
Reverse lock-out feature that prevents acciden-
tal selection of Reverse (instead of 1st gear).
SHIFTING TO REVERSE
Ⅲ
Lift up on the collar just below the shift knob,
then move the shift selector left and up into
Reverse.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT PASSENGER AIR BAG STATUS LIGHT
This vehicle is equipped with the Nissan Advanced Air Bag System.
Under some conditions, depending on the type of occupant or object
detected in the front passenger seat by the occupant classification
sensor, the front passenger air bag is designed to automatically turn
OFF. When the front passenger air bag is OFF, the front passenger
air bag status light will illuminate.* For example:
Ⅲ
When the system detects that the front passenger’s seat is
occupied by a small adult, child or child restraint as outlined in
the Owner’s Manual, the
will illuminate to indicate that the front passenger air
bag is OFF and will not inflate in a crash.
Ⅲ
When the front passenger’s seat is occupied and the passenger meets the conditions
outlined in the Owner’s Manual, the
will not illuminate to indicate that the front
passenger air bag is operational.
*When the system detects that the front passenger’s seat is unoccupied, the
passenger air bag status light will not illuminate, even though the front passenger
air bag is OFF.
TIRE PRESSURE MONITORING SYSTEM (TPMS)
This system monitors tire pressure. If the low tire pressure warning
light illuminates, check the tire pressure in all four tires.
Adjust the low tire pressure to the recommended COLD tire pres-
sure shown on the Tire and Loading Information label located in the
driver’s door opening. After tire pressures are adjusted, the vehicle
will need to be driven at speeds above 16 MPH (25 km/h) to activate
the TPMS and turn off the low tire pressure warning light.
SEAT BELT WARNING LIGHT AND CHIME
Ⅲ
The light and chime remind you to fasten your seat belts.
The light illuminates whenever the ignition switch is placed
in the ON or START position and remains illuminated until
the driver’s seat belt is fastened. At the same time, the
chime sounds for approximately 6 seconds unless the
driver’s seat belt is securely fastened.
Ⅲ
With the ignition ON, the seat belt warning light may also
illuminate if the front passenger’s seat is occupied with the
front passenger’s seat belt not fastened.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH (if so equipped)
The Vehicle Dynamic Control (VDC) system monitors driver inputs and
vehicle motion. Under certain conditions, it controls braking and engine
output to help improve traction or handling. VDC may need to be
temporarily shut off if you are trying to free a vehicle stuck in snow or mud.
Ⅲ
Push the Vehicle Dynamic Control (VDC) OFF switch to deactivate
the VDC system. The
gauge area.
light will illuminate in the instrument panel
Ⅲ
Ⅲ
Push the Vehicle Dynamic Control (VDC) OFF switch again to activate the VDC system.
The light in the instrument panel gauge area will turn off.
The VDC system is active while the vehicle is running until the switch is pushed to turn
it off.
REARVIEW MONITOR (if so equipped)
When the shift selector is moved to the R (Reverse) position,
the monitor display will automatically change to show the area
directly behind the vehicle.
The colored lines on the display screen indicate approximate
distances to objects.
Ⅲ
Red 1.5 ft (0.5 m); Yellow 3 ft (1 m); Green 7 ft (2 m) and
10 ft (3 m).
CHILD SAFETY REAR DOOR LOCK (Sedan Only)
Child safety locks help prevent the rear doors from being
opened accidentally, especially when small children are in
the vehicle. The child safety lock levers are located on the
edge of the rear doors. When the lever is in the LOCK
position, the door can only be opened from the outside.
FUEL-FILLER DOOR RELEASE
The fuel-filler door release is located on the floor to the left of the
driver’s seat.
Ⅲ
Ⅲ
To open the fuel-filler door, pull the release up.
To lock, close the fuel-filler door securely.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TRUNK LID CANCEL SWITCH
Ⅲ
When the cancel switch (located inside the glove box)
is OFF, the trunk lid cannot be opened with the trunk lid
opener (located on the instrument panel), the trunk
Request Switch button (if so equipped) or the Intelli-
gent Key button.
Ⅲ
It can be opened by using the Emergency Inside Trunk
Release.
MOONROOF CONTROLS (if so equipped)
The ignition switch must be in the ON position to operate
the moonroof controls.
TILTING THE MOONROOF
Ⅲ
To tilt the moonroof up, push the tilt switch toward
the position.
Ⅲ
To tilt the moonroof down, push the tilt switch toward
the position.
SLIDING THE MOONROOF
Ⅲ
Ⅲ
Ⅲ
To fully open the moonroof, push the switch toward the
To fully close the moonroof, push the switch toward the
position.
position.
To open or close the moonroof part way, push the switch in either direction (
or ) while the moonroof is sliding to stop it in the desired position.
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
FORWARD AND BACKWARD
Ⅲ
Pull the center of the bar up
under the front of the
seat and hold it while you slide the seat forward or
backward. Release the bar to lock the seat in position.
SEAT LIFTER (driver’s seat, if so equipped)
Ⅲ
Pull up or push down the adjusting lever
edly to adjust the seat height.
repeat-
RECLINING
Ⅲ
Lift the lever
on the side of the seat to adjust the seatback forward or backward.
Release the lever when you have found a comfortable angle and the seat belt fits
properly.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
With power seats (if so equipped):
The control lever
allows you to make the
following adjustments.
Ⅲ
Ⅲ
Move the control lever
forward or
backward to adjust the seat forward or
backward.
Coupe
Pull up or press down on the front of the
control lever
to adjust the front por-
tion of the driver’s seat cushion.
Ⅲ
Pull up or press down on the rear of the
control lever
rear portion of the driver’s seat cushion.
RECLINING
to raise or lower the
Sedan
Ⅲ
Push the reclining switch
move the seatback forward; pull it back to move the seatback backward.
LUMBAR SUPPORT (driver’s seat, if so equipped)
forward to
Ⅲ
Push the adjusting lever/switch
repeatedly to adjust the lumbar support.
PASSENGER REAR SEAT ENTRY (Coupe only)
FROM INSIDE THE VEHICLE
From the driver’s seat:
Ⅲ
Pull the upper seatback release lever
, located on the
inboard side of the passenger front seat, to the uppermost
position and slide the seat forward.
From the back seat:
Ⅲ
Step or push down on the lower seatback release lever
located on the backside lower portion of the passenger seat and push the seatback,
sliding it forward.
FROM OUTSIDE THE VEHICLE
From the driver’s side:
Ⅲ
Pull the upper seatback release lever
, located on the
outboard side of the driver’s front seat. (Return the seatback
manually by pushing the seatback rearward.)
From the passenger side:
Ⅲ
Pull the seatback release lever
fully up until the seatback
releases, and push the seatback, sliding it forward. (Return the seatback manually by
pushing the seatback rearward.)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLDING DOWN THE REAR SEATS
FROM INSIDE THE VEHICLE
Ⅲ
The rear seats can be locked using the mechanical key to
prevent unauthorized access.
Ⅲ
Open the access cover and press the release button
fold down the center/passenger’s side rear seat.
to
Ⅲ
Reach through the opening and pull on the strap
located
behind the seat to fold down the driver’s side rear seat.
FROM THE TRUNK
Ⅲ
Pull the strap
located behind the seat to fold down the
center/passenger’s side rear seat.
Ⅲ
Pull on the strap
located behind the seat to fold down the
driver’s side rear seat.
HOMELINKா UNIVERSAL TRANSCEIVER (if so equipped)
SYSTEM OPERATING TIPS
Ⅲ
Garage doors, electrical gates, entry doors, etc. will be activated during programming.
To avoid injury, make sure that people and objects are clear of all doors or gates during
programming. Your vehicle’s engine should be turned off while programming the
HomeLinkா Transceiver.
Ⅲ
To program your HomeLinkா Transceiver to operate a garage door, gate, or entry door
opener, home or office lighting, you need to be at the same location as the device.
NOTE: Garage door openers (manufactured after 1996) have “rolling code pro-
tection”. To program a garage door opener equipped with “rolling code protec-
tion”, you will need to use a ladder to get up to the garage door opener motor to
be able to access the “smart” or “learn” program button.
PROGRAMMING YOUR HOMELINKா UNIVERSAL TRANSCEIVER (Mirror,
Sun Visor or Overhead Console)
1. To begin, press and hold the two
outer HomeLinkா buttons (to clear
the memory) until the indicator light
blinks slowly (after 20 seconds).
Release both buttons.
2. Position the end of the hand-held
transmitter 1-3 in (26-76 mm) away
from the HomeLinkா surface.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Using both hands, simultaneously press and hold both the HomeLinkா button you want
to program and the hand-held transmitter button. DO NOT release the buttons until
step 4 has been completed.
4. Hold down both buttons until the indicator light on the HomeLinkா flashes, changing
from a “slow blink” to a “rapidly flashing blink”. This could take up to 90 seconds. When
the indicator light flashes rapidly, both buttons may be released. The rapidly flashing
light indicates successful programming. To activate the garage door or other pro-
grammed device, press and hold the programmed HomeLinkா button - releasing when
the device begins to activate.
5. If the indicator light on the HomeLinkா blinks rapidly for two seconds and then turns
solid, HomeLinkா has picked up a “rolling code” garage door opener signal. You will
need to proceed with the next steps to train the HomeLinkா to complete the program-
ming, which may require a ladder and another person for convenience.
6. Press and release the “smart” or “learn” program button located on the garage door
opener’s motor to activate the “training mode”. This button is usually located near the
antenna wire that hangs down from the motor. If the wire originates from under a light
lens, you will need to remove the lens to access the program button.
NOTE: Once you have pressed and released the program button on the garage
door opener’s motor and the “training light” is lit, you have 30 seconds in which
to perform step 7. Use the help of a second person for convenience to assist when
performing this step.
7. Quickly within 30 seconds of pressing and releasing the garage door opener program
button, firmly press and release the HomeLinkா button you’ve just programmed. Press
and release the HomeLinkா button up to three times to complete the training.
8. Your HomeLinkா button should now be programmed. (To program the remaining
HomeLinkா buttons for additional door or gate openers, follow steps 2-8 only.)
BLUETOOTHா HANDS-FREE PHONE SYSTEM (Without Navigation
System – if so equipped)
With an overhead microphone and sound
transmitted through the audio system
speaker, the Bluetoothா Hands-Free Phone
System utilizes Bluetoothா wireless technol-
ogy and voice recognition to provide hands-
free cellular phone communication.
SYSTEM OPERATING TIPS
Ⅲ
Close all windows. Surrounding noises
may interfere with system operation and
performance.
Ⅲ
Press the
button on the steering wheel to activate voice recognition.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Wait for the tone before speaking.
Begin speaking a command within 5 seconds of the tone.
To go back to the previous command, say “Go back” or “Correction”.
To cancel a voice recognition session, simply wait 5 seconds, say “Cancel” or “Quit”, or
press the
button.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Ⅲ
To increase or decrease the volume of the voice prompts, push the + or – (volume)
control buttons on the steering wheel or turn the VOL (volume) knob on the audio
system while the system is responding.
Ⅲ
Ⅲ
Speak in a clear and natural voice without pausing between words.
If the Voice Recognition system does not recognize your voice commands, train the
system using the Speaker Adaptation Mode. Refer to your Owner’s Manual for a list of
commands and further instructions.
Ⅲ
Ⅲ
Ⅲ
Some commands are not available while the vehicle is in motion.
The “Help” command can be used in any menu to hear a list of available commands.
Please refer to the cellular phone manufacturer Owner’s Manual for detailed information
regarding your Bluetoothா phone.
Ⅲ
For recommended phones and detailed instructions, please visit
PAIRING YOUR PHONE
To use the hands-free feature, you need to set-up, or pair, the system to recognize your
compatible cellular phone(s). Five Bluetoothா-enabled phones can be paired. After set-up,
the system automatically connects with a paired phone when the ignition is in the ACC or ON
position, as long as the phone is on and in the vehicle.
PAIRING PROCEDURE
NOTE: The vehicle must be stationary when pairing the phone.
1. Press the
button on the steering wheel and wait for the tone.
2. Say “Setup”.
3. Wait for the tone, then say “Pair phone”.
4. Wait for the tone, then say “New phone”.
5. Initiate pairing from the phone.
Ⅲ The pairing procedure varies according to each cellular phone model. For detailed
pairing instructions and a list of compatible phones, please visit
Ⅲ When prompted for a PASSKEY code, enter “1234” from the handset. (The PASS-
KEY code is assigned by NISSAN and cannot be changed.)
6. Say a name for the phone when the system asks you to provide one. You can give the
phone a name of your choice.
7. Say a number between 1 and 5 when the system asks you for a priority level. The priority
level determines which phone interacts with the system when two or more paired
phones are active in the vehicle at the same time. Choose 1 if this is the only phone or
the primary phone.
8. Say “Yes” or “No” when the system asks if you would like to select a custom ring tone.
Follow the instructions provided by the system to choose a ring tone.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING UP YOUR PHONEBOOK – ADDING NEW ENTRIES
Each paired phone has its own dedicated phonebook. Each phonebook can store up to 40
names. Each name can have up to 4 locations/numbers: Home, Office, Mobile, and Other.
NOTE: The vehicle must be stationary when adding new entries.
1. Press the
button and wait for the tone.
2. Say “Phonebook”.
3. Wait for the tone, then say “New entry”.
4. When prompted, say the name for the new entry. For example, say “Michelle”. If the
name is too short or too long, or if it sounds too much like a name that is already stored
in the phonebook, the system tells you and prompts you to say a name again. Choose a
new name.
5. Say “Yes” or “No” when the system asks you to confirm the name is correct.
6. Say a location (“Home,” “Office,” “Mobile” or “Other”) when the system asks you to
provide one. The system acknowledges the location.
Ⅲ By Voice command - When prompted, say a phone number for the location. For
example, say “five five five one two one two”. The system repeats the number and
prompts you for the next command.
Ⅲ By Bluetoothா transfer - When prompted, say “Transfer entry”. The system acknowl-
edges the command and asks you to initiate the transfer from the phone handset. The
new contact phone number will be transferred from the cellular phone via the
Bluetoothா communication link. The transfer procedure varies according to each
cellular phone. See the cellular phone owner’s manual for details.
7. Say “Store” when you are finished entering numbers. The system confirms the name,
location, and number.
8. Say “Yes”or “No”when the system asks if you would like to store another location for the
same name. If you do not respond to the system prompt, the system ends the New Entry
session.
MAKING A PHONE CALL
1. Press the
button.
2. After the tone, do one of the following:
Ⅲ Say “Call [name] [location]”. For example, say “Call Michelle Home”.
Ⅲ Say “Call [number]”. For example, say “Call 123-456-7891”.
Ⅲ Say “Redial” to redial the previous phone number called by the system.
Ⅲ Say “Call International” to dial more than 10 digits or any special characters.
RECEIVING/ENDING A PHONE CALL
When you receive a phone call, a ring tone sounds through the audio system.
Ⅲ
Ⅲ
To accept the call, press the
button. To reject the call, press the
button.
To hang up the phone at the end of a call or to disconnect during call placement, press
the
button.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO SAY NUMBERS
NISSAN voice recognition permits numbers to be spoken in a variety of ways.
Ⅲ
Ⅲ
Say “zero” or “oh” for “0”. Example: 1-800-662-6200 – Say “one eight zero zero six six
two six two oh oh”.
Say “pound” for “#”. Say “star” for “*” (available when using the “Call International”
command, and the “Send” command during a call).
Ⅲ
Ⅲ
Say “plus” for “+” (available only when using the “Call International” command).
Say “pause” for a 2 second pause (available only when storing a phonebook number).
BLUETOOTHா HANDS-FREE PHONE SYSTEM (Navigation System
only – if so equipped)
With an overhead microphone and sound
transmitted through the audio system
speaker, the Bluetoothா Hands-Free Phone
System utilizes Bluetoothா wireless technol-
ogy, touch-screen, and voice recognition to
provide hands-free cellular phone communi-
cation.
SYSTEM OPERATING TIPS
Ⅲ
Close all windows. Surrounding noises
may interfere with system operation and
performance.
Ⅲ
Press the
button on the steering wheel to activate voice recognition.
Ⅲ
Ⅲ
Wait for the “Please say a command” prompt and the listening tone before speaking.
Begin speaking a command within 1.5 seconds of the listening tone.
Ⅲ
Ⅲ
To cancel a voice recognition session, press and hold the
button.
button or press the
To increase or decrease the volume of the voice prompts, push the + or – (volume)
control buttons on the steering wheel or turn the VOL (volume) knob on the audio
system while the system is responding.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Speak in a clear and natural voice without pausing between words.
Some commands are not available while the vehicle is in motion.
The “Help” command will bring up the voice recognition command list.
Please refer to the cellular phone manufacturer Owner’s Manual for detailed information
regarding your Bluetoothா phone.
Ⅲ
For recommended phones and detailed instructions, please visit
20
Download from Www.Somanuals.com. All Manuals Search And Download.
PAIRING YOUR PHONE
Before using the hands-free feature, you need to set-up, or pair, the system to recognize your
compatible cellular phone(s). Five Bluetoothா-enabled phones can be paired. After set-up,
the system automatically connects with a paired phone when the ignition is in the ACC or ON
position, as long as the phone is on and in the vehicle.
PAIRING PROCEDURE
NOTE: The vehicle must be stationary when pairing
the phone.
INITIAL PAIRING
NOTE: This procedure can only be used to pair the
first phone to the system.
1. Press the
button on the steering wheel.
button again.
2. A message is displayed. Press the
3. The system will direct you to SETUP –> Phone –> Bluetooth Setup –> Pair Phone
menu.
4. Touch one of the “None (Add New)” keys.
5. Initiate pairing from the phone.
Ⅲ
The pairing procedure for cellular phones varies according to each cellular phone
model. For detailed pairing instructions and a list of compatible phones, please visit
Ⅲ The PIN code will appear on the screen; enter “1234” from the handset. (The PIN
code is assigned by NISSAN and cannot be changed.)
6. When the pairing is complete, the screen will show the phone’s listed name on the
paired phone list screen.
PAIRING ADDITIONAL PHONES/INITIAL PAIRING
NOTE: This procedure can be used to pair the first
phone and other additional phones to the system.
1. Press the SETUP button on the control panel.
2. Touch the “Phone” key on the touch-screen.
3. Scroll to the bottom of the list and touch the
“Bluetooth Setup” key.
4. Touch the “Pair Phone” key, then touch one of the “None (Add New)” keys.
5. Initiate pairing from the phone.
Ⅲ The pairing procedure for cellular phones varies according to each cellular phone
model. For detailed pairing instructions and a list of compatible phones, please visit
Ⅲ The PIN code will appear on the screen, enter “1234” from the handset. (The PIN
code is assigned by NISSAN and cannot be changed.)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
6. When the pairing is complete, the screen will show the phone’s listed name on the
paired phone list screen.
SETTING UP YOUR PHONEBOOK - ADDING NEW ENTRIES
Up to 70 phone numbers can be stored in the phone-
book.
NOTE: The vehicle must be stationary when adding
new entries.
1. Press the SETUP button, then touch the “Phone”
key.
2. Touch the “Phonebook” key.
3. Touch one of the “None (Add New)” keys from the
name list of the phonebook. There are different
methods to input a phone number. Select one of
the following options:
Ⅲ Enter Data by Keypad - Input the name and
phone number manually.
Ⅲ Downloaded Phonebook - Select an entry from a list of phone numbers you have
already transferred from your phone to your vehicle.
Ⅲ Outgoing Calls - Store the name and phone number from the outgoing call list.
Ⅲ Incoming Calls - Store the name and phone number from the incoming call list.
Ⅲ Bluetooth - Transfers an entry from your cellular phone to the Downloaded Phone-
book in the vehicle. The memory sending procedure from the cellular phone varies
according to each cellular phone model. See the cellular phone owner’s manual for
more details.
MAKING A PHONE CALL
1. Press the
button on the steering wheel.
2. After the tone, do one of the following:
Ⅲ Say “Phone Dial” then follow the voice prompts
to input the phone number. After the phone
number has been said, say “Dial”.
Ⅲ Say “Phonebook <voicetag>”. For example, say “Phonebook Michelle”.
Ⅲ Say “Phone Redial” to redial the previous phone number called by the system.
RECEIVING/ENDING A PHONE CALL
When you receive a phone call, a ring tone sounds
through the audio system (if enabled).
Ⅲ
To accept the call, press the
button on the
steering wheel or touch the “Answer” key. To reject
the call, touch the “Reject Call” key.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Ⅲ
To hang up the phone at the end of a call or to disconnect during call placement, press
the button.
HOW TO SAY NUMBERS
NISSAN Voice Recognition permits numbers to be spoken in a variety of ways.
Ⅲ
Ⅲ
Say “zero”or “oh”for “0”. Example: 1-800-662-6200 – Say “One eight zero zero six six
two six two oh oh”.
Say “Pound” for “#”. Say “star” for “*”. Example: 1-555-1212*123 – Say “One five five
five one two one two star one two three”.
NISSAN VOICE RECOGNITION SYSTEM (Navigation System only)
The NISSAN Voice Recognition system allows hands-
free operation of the systems equipped on this vehicle,
such as the phone and navigation systems.
To operate NISSAN Voice Recognition, press the
button located on the steering wheel. Then speak the
command for the system you wish to activate. The
command given is picked up by the microphone, and it is
performed when it is properly recognized. At this time, NISSAN Voice Recognition will
provide a voice and message (in the center display) to inform you of the command results. To
cancel the voice recognition, press the
button or press and hold the
button.
VOICE RECOGNITION COMMAND LIST
The following table lists some common voice recognition commands. For a complete list of
commands, say “Help.”
Destination
Destination Phone Number
Destination Address Book
Destination Home
Map Settings
Birdview Map
Plan View Map
North Up
Destination Nearby Places
Destination < Voicetag >
Destination Previous Destinations
Route Settings
Heading Up
Zoom Level < 1-10 >
Phone
Recalculate Route
Phone Dial
Cancel Route
Phone Redial
Shortest Distance Route
Phonebook
Phone Select
Phonebook < voicetag >
23
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION SYSTEM (if so equipped)
GETTING STARTED
The Navigation System begins when the ignition switch is placed in the ACC or ON position.
To help ensure safe driving, some functions are grayed out, or muted, while driving. Park the
vehicle in a safe location and then operate the Navigation System.
BASIC FUNCTIONS
START-UP SCREEN
Ⅲ
Read the precautions carefully, and touch the
“I agree” key to accept.
NAVIGATION DISPLAY SCREEN
Ⅲ
Displays navigation features and map.
DISABLED WHILE DRIVING
Ⅲ
Not all features can be manually operated
while the vehicle is in motion. The text for
these restricted features turns from white to
gray and cannot be selected. Alternatively, the
voice recognition system may have a related
command that can be used at any time.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
DAY/NIGHT BUTTON
Ⅲ
Press the
button
to switch be-
tween the day screen (bright) and the night
screen (dark). Within 10 seconds of pressing
the
brightness of the map display screen by
touching the key or the key.
button
, you can adjust the
USING THE TOUCH-SCREEN
Ⅲ
To maneuver around the navigation display
screen, touch the screen to select the item or
key displayed. To move around the map
screen, touch and hold to scroll around.
SETUP BUTTON
Ⅲ
Press the SETUP button
to change or
set navigation preferences.
DEST (DESTINATION) BUTTON
Ⅲ
Press the DEST button
to display the
address book and alternative ways of pro-
gramming a destination.
MAP BUTTON
Ⅲ
Press the MAP button
current location map screen.
to display the
INFO BUTTON
Ⅲ
Press the INFO button
to view various
information including real-time traffic informa-
tion (requires a subscription to XMா NavTraf-
fic™ service) and other navigation information.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUTE KEY
Ⅲ
Press the MAP button
to show the cur-
rent location map screen. Touch the “Route”
key while in a current location map screen to
display the Route menu screen. The Route
menu screen displays various ways to modify
the route to a destination.
ZOOM OUT/IN KEYS
Ⅲ
Touch the “ZOOM OUT” key or the “ZOOM
IN” key to increase or decrease the scale of
the map display.
BACK KEY
Ⅲ
Touch the “Back” key to return to the previous
function shown on the navigation display.
VOICE KEY
Ⅲ
Touch the “Voice” key to hear the current
navigation instructions.
SWITCHING THE MAP VIEW
Ⅲ
Press the MAP button
. The current lo-
cation map screen is displayed.
Touch the “Menu” key.
Ⅲ
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Ⅲ
Ⅲ
Touch the “Map view” key.
Touch either the “2D” key or the “3D” key to
select the map view. Press the MAP
button
or the “Back” key to accept the
changes.
2D PLAN VIEW
Ⅲ
Displays the map in a 2-dimensional environ-
ment similar to a road map.
3D BIRDVIEW™
Ⅲ
Displays the map in an elevated perspective.
SELECTING A MENU SCREEN
1. To select a preferred menu key, touch the corresponding key on the screen.
2. Depending on the key you selected, a detailed menu screen, a character input screen or
a setting screen, etc. is displayed. On the screen displayed, make adjustments, input
information, etc. accordingly.
3. Touch the “Back” key to return to the previous screen without applying any changes; in
some cases pressing the “Back” key will accept the changes you made.
4. Press the MAP button
to return to the current location map screen without
applying any changes.
NOTE: Depending on the menu selected, pressing the MAP button
may not return
you to the current location map screen.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
STORING YOUR HOME IN YOUR ADDRESS BOOK
Ⅲ
Ⅲ
Press the DEST button
.
Touch the “Home (Add New)” key. If you have
already stored your home, this key may not
appear.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
When you touch the “Home (Add New)”key, a
confirmation message is displayed. Touch the
“Yes” key.
Touch the “Street Address” key. A character
input screen is displayed.
Enter the address of your home, touch the
“OK” key. A list is displayed.
Touch the preferred home address key from
the list. You may need to touch the scroll
or
key to find the preferred home address
key.
Ⅲ
Ⅲ
Your home is displayed at the center of the
map. A confirmation message is displayed,
and the system sets your home as the desti-
nation.
Press the MAP button
to return to the
current location map screen. The home icon is
displayed on the screen.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING A STREET ADDRESS AS A DESTINATION
Ⅲ
Ⅲ
Press the DEST button
.
Touch the “Street Address” key. A character
input screen is displayed.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Enter the house number; when finished touch
the “OK” key. If you do not know the house
number, touch the “No House #” key.
Enter the name of the street. After finishing the
entry, touch the “OK” key. A list of possible
street addresses is displayed.
Touch the correct address of the destination
from the list. You might need to touch the
scroll
key.
or
key to find the preferred home
The selected destination is displayed at the
center of the map. Touch the “Start” key after
confirming the location of the displayed des-
tination. The system sets the destination to the
selected location and starts calculating a
route.
MOVING AROUND WITHIN A MAP
You can manually move across the map to view the surrounding area or to view a preferred
location.
Ⅲ
Touch the screen in the direction that you want to move across the map. Once you begin
moving on the map, the cross pointer appears.
Ⅲ
Press the MAP button
or touch the “Back” key to return to the current location
map screen. The cross pointer disappears.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING A POINT OF INTEREST
Ⅲ
Ⅲ
Press the DEST button
.
Touch the “Points of Interest” key.
Ⅲ
Touch one of the category keys; the “Travel”
key is used in this example.
Ⅲ
Ⅲ
Touch a sub-category key; the “Airport” key is
used in this example.
You can find a Point of Interest (POI) three
ways:
● Nearby POI - lists POIs in order of proxim-
ity.
● By Name (used in this example).
● By City.
Ⅲ
Enter the facility name to narrow down your
search. DTW is used in this example.
Ⅲ
Ⅲ
Touch one of the preferred airport keys from
the list.
The selected destination is displayed at the
center of the map. Touch the “Start” key after
confirming the location of the displayed des-
tination. The system sets the destination to the
selected location and starts calculating a
route.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
BEGINNING ROUTE GUIDANCE
After setting a destination and performing route calculation, the suggested route is dis-
played.
Ⅲ
Touch the “Start”key. The system will navigate
you through the guide points using visual and
voice guidance.
Ⅲ
Ⅲ
When approaching a guide point, the system
automatically changes to the split screen and
shows an enlarged view of the intersection in
the right screen.
When arriving at the destination, the route
guidance automatically ends.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
SHIFT_
Nissan, the Nissan Brand Symbol, ЉSHIFT_Љ tagline, Z and Nissan model names are Nissan trademarks.
© 2008 Nissan North America, Inc.
QR9E-0L32U1
Printing: October 2008 (09)
Download from Www.Somanuals.com. All Manuals Search And Download.
|