JVC MP3 Player RC EX16B User Manual

GETTING STARTED

POWERING UP

This CD portable system operates on battery or AC power.

ENGLISH

BEAT CUT/FM

MODE switch

FM telescopic

antenna

CD PORTABLE SYSTEM

BATTERY POWER

Insert six batteries R20 (SUM-1)/D (13D) (not supplied) and you

can take your system just about anywhere. Open the battery

compartment door on the back of the unit by pressing down the

two tabs and pulling out the cover. Insert batteries as marked on

the back.

RC-EX16B/RC-EX16A

Important Battery Information

Battery compartment

AC IN jack

•

If you are not going to use your system for a month or more, be

sure to remove batteries because they can leak and cause

damage.

•

Dispose of batteries in the proper manner, according to federal,

state, and local regulations.

Discard leaky batteries immediately. Leaking batteries can

cause skin burns or other personal injury.

PHONES jack

AC POWER

Plug the power supply cord into the Ó AC IN jack on the back of the unit, and into an AC power outlet.

CAUTIONS:

1. ONLY USE JVC POWER CORD PROVIDED WITH THIS UNIT TO AVOID MALFUNCTION OR DAMAGE

TO THE UNIT. REMOVE BATTERIES WHEN USING THE POWER CORD.

2. BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN THE

UNIT IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.

USING HEADPHONES

Connect commercially available headphones to the PHONES jack on the rear of the main unit. While the head-

phones are connected, the speakers do not produce any sound. Before connecting the headphones, make sure

to turn down the sound volume.

INSTRUCTIONS

LVT1374-003A [B]

Thank you for purchasing this JVC product.

Please read these instructions carefully before starting operation to be sure to

obtain optimum performance and a longer service life from the unit.

ANTENNAS

The AM antenna is built in, so adjusting the position of the unit may help AM reception. The FM telescopic

antenna on the back of the unit can be extended and rotated for better FM reception.

SAFETY PRECAUTIONS

GENERAL CONTROLS

FUNCTION switch – Move the switch to select which part of this system you want to select – TUNER, TAPE or

IMPORTANT for the U.K.

CD.

VOLUME – Turn the volume knob to increase or decrease the volume to desired level.

HBS – Press so that the HBS indicator lights. You can enjoy powerful bass sound with the Hyper-Bass Sound

effect.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in

your home or the cable is too short to reach a power point, then obtain an appropriate safety approved

extension lead or consult your dealer.

POWER OFF – Move FUNCTION to OFF/TAPE with no cassette button pressed, to turn the unit off.

BE SURE to replace the fuse only with an identical approved type, as originally fitted.

If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to

avoid a possible shock hazard by inadvertent connection to the mains supply.

USING THE RADIO

TUNING IN RADIO STATIONS

If this product is not supplied fitted with a mains plug then follow the instructions given below:

Move FUNCTION to TUNER to turn the radio on.

IMPORTANT.

•

Set BAND to AM or FM.

Tune in desired station by turning the TUNING knob.

To turn off the radio, move FUNCTION to OFF/TAPE.

DO NOT make any connection to the terminal which is marked with the letter E or by the safety earth

symbol or coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in accordance with the following code:

BEAT CUT/FM MODE SWITCH

Blue :

Neutral

•

When recording an AM broadcast

Brown : Live

When recording an AM broadcast, beats may occur. If this happens, set the switch

to “1” or “2.”

Changing the FM reception mode

When an FM stereo broadcast is hard to receive or noisy, set the switch to “MONO.”

Reception improves.

To restore the stereo effect, switch to “STEREO.”

As these colours may not correspond with the coloured markings identifying the terminals in your plug

proceed as follows:

BEAT CUT

•

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or

coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or

coloured red.

STEREO

MONO

FM MODE

IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.

USING THE TAPE

Caution ––

OFF switch!

Disconnect the mains plug to shut the power off completely. The switch in any position does not disconnect

the mains line. The power cannot be remote controlled.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

PAUSE – Press to interrupt tape play or record mode. Press a second time to resume tape play or tape record

mode.

STOP/EJECT

– Press to stop the current tape activity, or to open the cassette compartment door when no

buttons are active.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

– In stop mode, press to advance the tape toward the end. (When the tape reaches the end, press

STOP/EJECT to release the depressed button.)

– In stop mode, press to rewind the tape toward the beginning. (When the tape reaches the end, press

STOP/EJECT to release the depressed button.)

CAUTION: Do not open the top cover. There are no user serviceable parts inside the

REW

unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or

defeated. Avoid direct exposure to beam.

PLAY

REC

– Press to play cassettes.

– Press to record from the radio or CD player.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.

PLAYING A CASSETTE TAPE

1. Move FUNCTION to OFF/TAPE.

CAUTION - INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS

DEFEATED. AVOID EXPOSURE TO BEAM.

2. Press STOP/EJECT

to open the cassette compartment door.

VORSICHT ! UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL

GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG

3. Insert a cassette tape into the compartment with the exposed part of the tape facing up and the side you want

to play facing toward you.

4. Close the door securely.

ÜBERBRÜCKT IST. NICHT DEM STRAHL AUSSETZEN!

VARNING - OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH

SPÄRR ÄR URKOPPLAD STRÅLEN ÄR FARLIG.

5. Press REW

6. Press PLAY

or FF

to move the tape to the desired starting point.

to begin playing the tape. The cassette tape plays until it reaches the end of the side, then it

ADVARSEL - USYNLIG LASERSTRÅLING VED ÅBNING NÅR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ

UDSÆTTELSE FOR STRÅLING.

automatically stops.

RECORDING ON CASSETTE TAPES

You can record from the radio or the CD player.

For best recording, use normal bias tape.

Caution: Proper Ventilation

Front view

It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without

the consent of the owner of copyright in the sound or video recording, broadcast or cable program

and in any literary, dramatic, musical, or artistic work embodied therein.

15 cm

To avoid risk of electric shock and fire, and to prevent damage, locate

the apparatus as follows:

15 cm

Front:

ERASE PROTECTION

No obstructions and open spacing.

Sides/ Top/ Back:

When you record new material, the cassette deck records over what-

ever is on a tape. To protect a tape from accidental erasure, break

off one or both plastic tabs (one for each tape side) on the top of the

cassette tape. If you decide later to record on the tape, seal the

hole with a piece of cellophane tape.

10 cm

No obstructions should be placed in the areas shown in the

illustration on the right.

15 cm

Side view

Bottom:

15 cm

Place on the level surface. Maintain an adequate air path for

ventilation by placing on a stand with a height of 10 cm or more.

15 cm

WARNING

10 cm

A little bit of slack in your tape can cause scratches on the tape, or worse yet, the tape

could break. If you notice some slack in the tape, use a pencil to tighten it up before you

insert it in the tape deck.

TIP

The use of tapes longer than 120 minutes is not recommended, since characteristic deterioration may occur and

these tapes easily jam in the pinch-roller and the capstan.

Turn Over

0205NSMBICORI

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING FROM THE RADIO

1. Insert a cassette tape into the tape deck and close the door.

2. Move FUNCTION to TUNER and select a radio station.

CARE AND MAINTENANCE

CLEANING THE EXTERIOR

GETTING STARTED

POWERING UP

ENGLISH

FM telescopic antenna

BEAT CUT/FM MODE switch

3. Press REC

to begin recording. REC

and PLAY

lock down.

This CD portable system operates on battery or AC power.

•

Disconnect the system from AC power before cleaning the exterior of the unit with a soft dust cloth.

4. Press STOP/EJECT

to end recording.

CD PORTABLE SYSTEM

BATTERY POWER

HANDLING CDS

5. To turn off the radio, slide FUNCTION to OFF/TAPE.

Insert six batteries R20 (SUM-1)/D (13D) (not supplied) and you

can take your system just about anywhere. Open the battery

compartment door on the back of the unit by pressing down the

two tabs and pulling out the cover. Insert batteries as marked on

the back.

•

Do not touch the signal surfaces. Hold by the edges, or by one edge and the hole.

Do not affix labels or adhesive tape to the label surfaces. Also, do not scratch or damage the label.

Discs rotate at high speed inside the player. Do not use damaged (cracked or warped) discs.

RC-EX16B/RC-EX16A

RADIO RECORDING TIPS

•

To temporarily pause the recording, press PAUSE on the cassette deck. Press PAUSE again to resume

recording.

CLEANING CDS

SYNCHRONIZED RECORDING FROM A CD

1. Insert a cassette tape into the tape deck and close the door.

2. Move FUNCTION to CD.

3. Insert the CD you want to record into CD compartment.

4. Select the track you want to record by pressing

5. Press REC to start recording.

Note that the tape continues to run when the CD finishes playing, or the CD continues to play when the tape

reaches the end.

•

Dirty discs can cause poor sound quality. Always keep discs clean by wiping them gently with a soft cloth from

the inner edge toward the outer perimeter.

If a disc becomes dirty, wet a soft cloth in water, wring it out well, wipe the dirt away gently, and then remove

any water drops with a dry cloth.

Do not use record cleaning sprays or antistatic agents on discs. Also, never clean discs with benzene, thin-

ner, or other volatile solvents which may cause damage to the disc surface.

Important Battery Information

Battery compartment

AC IN jack

•

If you are not going to use your system for a month or more, be

sure to remove batteries because they can leak and cause

damage.

(skip/search) or

(skip/search).

•

Dispose of batteries in the proper manner, according to federal,

state, and local regulations.

Discard leaky batteries immediately. Leaking batteries can

cause skin burns or other personal injury.

PHONES jack

TAPE CARE

•

Do not expose tapes to sunlight or store in hot places. High temperatures may warp the shell or damage the

tape itself.

Keep cassettes in their boxes when not in use.

Cassette tapes can be erased by magnetic fields produced by magnets, electric motors, electrical transform-

ers, and other devices. Keep tapes away from magnets and magnetic fields.

TIP

AC POWER

Using the PAUSE

button on the cassette deck instead of the STOP/EJECT

button to momentarily

•

Plug the power supply cord into the Ó AC IN jack on the back of the unit, and into an AC power outlet.

interrupt recording gives you a much cleaner sound recording.

CAUTIONS:

1. ONLY USE JVC POWER CORD PROVIDED WITH THIS UNIT TO AVOID MALFUNCTION OR DAMAGE

TO THE UNIT. REMOVE BATTERIES WHEN USING THE POWER CORD.

2. BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN THE

UNIT IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.

USING THE CD

CLEANING THE TAPE HEADS

Iron oxide particles from the magnetic tape can build up on the parts that come in contact with the tape. These

deposits can cause incomplete erasure, muffled playback sound, and might prevent automatic stop.

FUNCTION

CD door

) PUSH

skip/search

backward

To clean a cassette deck, open the compartment door, press PLAY

pinch wheel with a head cleaner.

Always unplug the power cord before cleaning, and allow 30 minutes drying time after using a liquid cleaner.

Clean heads after every 25 hours of use.

and gently clean the heads, capstan, and

USING HEADPHONES

Connect commercially available headphones to the PHONES jack on the rear of the main unit. While the head-

phones are connected, the speakers do not produce any sound. Before connecting the headphones, make sure

to turn down the sound volume.

INSTRUCTIONS

PUSH

skip/search

forward

REPEAT

•

Demagnetize the head occasionally with a head demagnetizing cassette (available from many audio equip-

ment stores).

REPEA

Thank you for purchasing this JVC product.

Please read these instructions carefully before starting operation to be sure to

obtain optimum performance and a longer service life from the unit.

RANDOM

STOP 7

USE

Y/P

PLA

ANTENNAS

OGRAM

RANDOM

•

Never use any metal objects on or near the tape heads.

Do not allow any cleaning material to fall into the tape assembly.

REMOTE

SENSOR

HBS

The AM antenna is built in, so adjusting the position of the unit may help AM reception. The FM telescopic

antenna on the back of the unit can be extended and rotated for better FM reception.

LVT1374-004A [E]

PLAY/PAUSE

PROGRAM

0205NSMBICORI

REMOTE FUNCTIONS (FOR CD OPERATION ONLY)

GENERAL CONTROLS

FUNCTION switch – Move the switch to select which part of this system you want to select – TUNER, TAPE or

When inserting batteries R03 (UM-4) / AAA (24F)

LOADING A CD

SAFETY PRECAUTIONS

STOP

PLAY/PAUSE

CD.

Match the polarity (+ and –) on the batteries with the +

and – markings in the battery compartment on the back

of the unit.

1. Move FUNCTION to CD; “– –” flashes, then “no” appears in the display if no CD is loaded.

2. Press ) PUSH to open the CD door.

3. Place a CD into the tray with the label facing up.

4. Close the CD door. Then the total number of tracks appears.

5. To remove the CD, press ) PUSH, grasp the CD by its edges, and carefully pull it out.

VOLUME – Turn the volume knob to increase or decrease the volume to desired level.

HBS – Press so that the HBS indicator lights.You can enjoy powerful bass sound with the Hyper-Bass Sound

effect.

STOP

SKIP/SEARCH-UP

(forward)

SKIP/SEARCH-DOWN

(backward)

Caution ––

OFF switch!

Disconnect the mains plug to shut the power off completely. The switch in any position does not disconnect

the mains line. The power cannot be remote controlled.

PROGRAM

REPEAT

PROGRAM

REPEAT

POWER OFF – Move FUNCTION to OFF/TAPE with no cassette button pressed, to turn the unit off.

CAUTION

PLAYING A CD

Press PLAY/PAUSE

in the display.

Note: Press PLAY/PAUSE

display. Press PLAY/PAUSE

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

USING THE RADIO

TUNING IN RADIO STATIONS

Move FUNCTION to TUNER to turn the radio on.

Set BAND to AM or FM.

Tune in desired station by turning the TUNING knob.

To turn off the radio, move FUNCTION to OFF/TAPE.

to play all the tracks in order starting with track 1. The current track number appears

TROUBLESHOOTING TIPS

to temporarily stop the CD. The

again to resume playing the CD.

indicator and the track number flash in the

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

CAUTION: Do not open the top cover. There are no user serviceable parts inside

the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or

defeated. Avoid direct exposure to beam.

•

Problem

Solution

•

Adjust VOLUME to a comfortable level.

Press STOP 7 to stop playing the CD. Wait a few seconds for the CD to stop turning, then press ) PUSH to

open the CD compartment door and remove the CD.

• Make sure power cord is securely plugged into the AC power outlet (or that

the batteries are fresh).

• Unplug the unit for a moment, and then plug it back in again.

• Check the outlet by plugging in another device.

System doesn’t turn on.

BEAT CUT/FM MODE SWITCH

When recording an AM broadcast

AUTOMATIC SEARCH

•

• Adjust volume setting.

• Make sure you have selected the correct function: CD, TAPE, or TUNER

and the headphones are disconnected.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.

When recording an AM broadcast, beats may occur. If this happens, set the switch

to “1” or “2.”

Changing the FM reception mode

When an FM stereo broadcast is hard to receive or noisy, set the switch to

“MONO.”

Reception improves.

Automatic search lets you quickly locate the beginning of any track on the CD, including the track currently

playing. If the CD is playing:

BEAT CUT

No sound

•

Press

beginning of the previous track.

Press (skip/search) to skip to the beginning of the next track.

(skip/search) once to return to the beginning of the current track, press twice to return to the

CAUTION - INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS

DEFEATED. AVOID EXPOSURE TO BEAM.

STEREO

MONO

• Adjust the FM telescopic antenna for better FM reception.

• Rotate the unit to achieve better AM reception.

• Try turning off electrical appliances near the unit, such as TV, hair dryers,

vacuum cleaners, or fluorrescent lights.

FM MODE

Poor radio reception

VORSICHT ! UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL

GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG

If the CD is stopped, repeatedly press

of the track you want to play, then press PLAY/PAUSE

(skip/search) or

(skip/search) until the display shows the number

. The CD player starts playing the selected track.

ÜBERBRÜCKT IST. NICHT DEM STRAHL AUSSETZEN!

To restore the stereo effect, switch to “STEREO.”

• Make sure the tray contains a CD.

VARNING - OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH

SPÄRR ÄR URKOPPLAD STRÅLEN ÄR FARLIG.

TRACK SEARCH

• Make sure the CD’s label is facing up.

• Make sure that pause mode is not activated.

• Make sure CD function is selected.

CD doesn’t play.

CD sound skips.

USING THE TAPE

•

In play mode, press and hold

(skip/search) to move forward through a track at high speed.

(skip/search) to move backward through a track at high speed.

ADVARSEL - USYNLIG LASERSTRÅLING VED ÅBNING NÅR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ

UDSÆTTELSE FOR STRÅLING.

• Clean the CD (as explained in “CARE AND MAINTENANCE”).

• Check CD for warping, scratches, or other damage.

• Check for vibration or shock that may affect the unit; move system if

necessary.

REPEAT

The REPEAT button allows you to repeat one track (REP 1) or all tracks (REP ALL). To scroll through the

choices, continuously press and release REPEAT and check the display to see which choice you have selected.

The following chart illustrates how REPEAT works in various modes.

Caution: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

• Inspect the recording head and clean it if necessary.

• Demagnetize recording head (as explained in “CARE AND

MAINTENANCE”).

Distorted or noisy

recordings

PAUSE – Press to interrupt tape play or record mode. Press a second time to resume tape play or tape record

NORMAL

REP 1

REP ALL

Front:

mode.

No obstructions and open spacing.

Sides/ Top/ Back:

No obstructions should be placed in the areas shown by the dimensions below.

Bottom:

STOP/EJECT

– Press to stop the current tape activity, or to open the cassette compartment door when no

buttons are active.

RANDOM

Press RANDOM so that “RAND” appears in the display.Start play by pressing PLAY/PAUSE

, and the tracks

SPECIFICATION

– In stop mode, press to advance the tape toward the end. (When the tape reaches the end, press

STOP/EJECT to release the depressed button.)

– In stop mode, press to rewind the tape toward the beginning. (When the tape reaches the end, press

STOP/EJECT to release the depressed button.)

are played in random order.

To quit random play, press RANDOM again.

CD player

CD capacity

Dynamic range

Signal-to-noise ratio : 75 dB

Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a

height of 10 cm or more.

General

Speaker

Power output

REW

: 1 CD

: 60 dB

: 9 cm cone × 2 (4 Ω)

: 4 W (2 W + 2 W) at 4 Ω

(10% THD) (IEC268-3)

: PHONES × 1 (∅ 3.5 mm,

stereo)

: AC 230 V Ó, 50 Hz

DC 9 V (“R20 (SUM-1)/D

(13D)” × 6)

PROGRAMMING

Press PROGRAM to enter program edit mode.

PLAY

REC

– Press to play cassettes.

– Press to record from the radio or CD player.

Front view

Side view

15 cm

“00” and “PROG” will flash in the display. Press

(skip/search) or

(skip/search) to select the track

Output terminals

Power supply

number and press PROGRAM to store the number in program place. You can repeat these steps to program up

to 20 tracks. Note that programming more than 20 tracks will overwrite the tracks already programmed.

During program play, “PROG”lights steadily.To confirm the program order, press PROGRAM in stop mode.Each

time you press PROGRAM, the program number appears, then the corresponding track number flashes in order

from the first programmed track.

15 cm

PLAYING A CASSETTE TAPE

1. Move FUNCTION to OFF/TAPE.

15 cm

Tuner

Frequency ranges

15 cm

: FM 88 - 108 MHz

: AM 540 - 1 600 kHz

: Telescopic antenna for FM

Ferrite core antenna for AM

2. Press STOP/EJECT

to open the cassette compartment door.

10 cm

3. Insert a cassette tape into the compartment with the exposed part of the tape facing up and the side you want

to play facing toward you.

4. Close the door securely.

Antenna

Power consumption : 12 W (at operation), 3 W (on

standby)

To clear the entire program in the memory, turn the unit off, or open the CD door.

Dimensions

: 420 mm (W) × 178 mm (H) ×

249 mm (D)

: Approx. 3.2 kg (without

batteries)

5. Press REW

6. Press PLAY

or FF

to move the tape to the desired starting point.

This unit has been designed only to play back the following CDs.

to begin playing the tape. The cassette tape plays until it reaches the end of the side, then it

Cassette deck section

Frequency response : 60 Hz - 10 000 Hz

•

Digital audio CD

Recordable digital audio CD (CD-R)

Rewritable digital audio CD (CD-RW)

Mass

automatically stops.

Wow and flutter

: 0.15% (WRMS)

RECORDING ON CASSETTE TAPES

You can record from the radio or the CD player.

For best recording, use normal bias tape.

Accessories provided : AC power cord × 1

Remote control unit × 1

Batteries for the remote

control unit R03 (UM-4)/AAA

(24F) × 2

When playing a CD-R or CD-RW

You can play back finalized CD-R or CD-RW recorded in music CD format. (If a CD-RW has been recorded in a

different format, erase all the data on the CD-RW completely before recording on it.)

•

It may be unlawful to record or play back copyrighted material without the consent of the copyright

owner.

•

You can play back CD-R or CD-RW like an audio CD.

Some CD-R or CD-RW may not be played back on this unit because of their disc characteristics, damage or

stain on them, or if the player lens is dirty.

ERASE PROTECTION

•

The reflection factor of CD-RW is lower than that of other CDs, possibly causing CD-RW to take longer time

to read.

CD-R and CD-RW of MP3 format cannot be played back.

When you record new material, the cassette deck records over what-

ever is on a tape. To protect a tape from accidental erasure, break

off one or both plastic tabs (one for each tape side) on the top of the

cassette tape. If you decide later to record on the tape, seal the

hole with a piece of cellophane tape.

Design and specifications are subject to change without notice.

Caution for DualDisc playback

The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore,

the use of Non-DVD side of a DualDisc on this product may not be recommended.

WARNING

A little bit of slack in your tape can cause scratches on the tape, or worse yet, the tape

could break. If you notice some slack in the tape, use a pencil to tighten it up before you

insert it in the tape deck.

TIP

The use of tapes longer than 120 minutes is not recommended, since characteristic deterioration may occur and

these tapes easily jam in the pinch-roller and the capstan.

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING FROM THE RADIO

1. Insert a cassette tape into the tape deck and close the door.

2. Move FUNCTION to TUNER and select a radio station.

CARE AND MAINTENANCE

CLEANING THE EXTERIOR

GETTING STARTED

POWERING UP

FM telescopic antenna

BEAT CUT/FM MODE switch

ENGLISH

3. Press REC

to begin recording. REC

and PLAY

lock down.

This CD portable system operates on battery or AC power.

•

Disconnect the system from AC power before cleaning the exterior of the unit with a soft dust cloth.

4. Press STOP/EJECT

to end recording.

CD PORTABLE SYSTEM

BATTERY POWER

HANDLING CDS

5. To turn off the radio, slide FUNCTION to OFF/TAPE.

Insert six batteries R20 (SUM-1)/D (13D) (not supplied) and you

can take your system just about anywhere. Open the battery

compartment door on the back of the unit by pressing down the

two tabs and pulling out the cover. Insert batteries as marked on

the back.

•

Do not touch the signal surfaces. Hold by the edges, or by one edge and the hole.

Do not affix labels or adhesive tape to the label surfaces. Also, do not scratch or damage the label.

Discs rotate at high speed inside the player. Do not use damaged (cracked or warped) discs.

RC-EX16B/RC-EX16A

RADIO RECORDING TIPS

•

To temporarily pause the recording, press PAUSE on the cassette deck. Press PAUSE again to resume

recording.

CLEANING CDS

SYNCHRONIZED RECORDING FROM A CD

1. Insert a cassette tape into the tape deck and close the door.

2. Move FUNCTION to CD.

3. Insert the CD you want to record into CD compartment.

4. Select the track you want to record by pressing

5. Press REC to start recording.

Note that the tape continues to run when the CD finishes playing, or the CD continues to play when the tape

reaches the end.

•

Dirty discs can cause poor sound quality. Always keep discs clean by wiping them gently with a soft cloth from

the inner edge toward the outer perimeter.

If a disc becomes dirty, wet a soft cloth in water, wring it out well, wipe the dirt away gently, and then remove

any water drops with a dry cloth.

Do not use record cleaning sprays or antistatic agents on discs. Also, never clean discs with benzene, thin-

ner, or other volatile solvents which may cause damage to the disc surface.

Important Battery Information

Battery compartment

AC IN jack

•

If you are not going to use your system for a month or more, be

sure to remove batteries because they can leak and cause

damage.

(skip/search) or

(skip/search).

•

Dispose of batteries in the proper manner, according to federal,

state, and local regulations.

Discard leaky batteries immediately. Leaking batteries can

cause skin burns or other personal injury.

PHONES jack

TAPE CARE

•

Do not expose tapes to sunlight or store in hot places. High temperatures may warp the shell or damage the

tape itself.

Keep cassettes in their boxes when not in use.

Cassette tapes can be erased by magnetic fields produced by magnets, electric motors, electrical transform-

ers, and other devices. Keep tapes away from magnets and magnetic fields.

TIP

AC POWER

Using the PAUSE

button on the cassette deck instead of the STOP/EJECT

button to momentarily

•

Plug the power supply cord into the Ó AC IN jack on the back of the unit, and into an AC power outlet.

interrupt recording gives you a much cleaner sound recording.

CAUTIONS:

1. ONLY USE JVC POWER CORD PROVIDED WITH THIS UNIT TO AVOID MALFUNCTION OR DAMAGE

TO THE UNIT. REMOVE BATTERIES WHEN USING THE POWER CORD.

2. BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN THE

UNIT IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.

USING THE CD

CLEANING THE TAPE HEADS

Iron oxide particles from the magnetic tape can build up on the parts that come in contact with the tape. These

deposits can cause incomplete erasure, muffled playback sound, and might prevent automatic stop.

FUNCTION

CD door

) PUSH

skip/search

backward

To clean a cassette deck, open the compartment door, press PLAY

pinch wheel with a head cleaner.

Always unplug the power cord before cleaning, and allow 30 minutes drying time after using a liquid cleaner.

Clean heads after every 25 hours of use.

and gently clean the heads, capstan, and

USING HEADPHONES

Connect commercially available headphones to the PHONES jack on the rear of the main unit. While the head-

phones are connected, the speakers do not produce any sound. Before connecting the headphones, make sure

to turn down the sound volume.

INSTRUCTIONS

PUSH

skip/search

forward

REPEAT

•

Demagnetize the head occasionally with a head demagnetizing cassette (available from many audio equip-

ment stores).

REPEA

Thank you for purchasing this JVC product.

Please read these instructions carefully before starting operation to be sure to

obtain optimum performance and a longer service life from the unit.

RANDOM

STOP 7

USE

Y/P

PLA

ANTENNAS

OGRAM

RANDOM

•

Never use any metal objects on or near the tape heads.

Do not allow any cleaning material to fall into the tape assembly.

REMOTE

SENSOR

HBS

The AM antenna is built in, so adjusting the position of the unit may help AM reception. The FM telescopic

antenna on the back of the unit can be extended and rotated for better FM reception.

LVT1374-007A [EN]

PLAY/PAUSE

PROGRAM

0205NSMBICORI

REMOTE FUNCTIONS (FOR CD OPERATION ONLY)

GENERAL CONTROLS

FUNCTION switch – Move the switch to select which part of this system you want to select – TUNER, TAPE or

When inserting batteries R03 (UM-4) / AAA (24F)

LOADING A CD

SAFETY PRECAUTIONS

STOP

PLAY/PAUSE

CD.

Match the polarity (+ and –) on the batteries with the +

and – markings in the battery compartment on the back

of the unit.

1. Move FUNCTION to CD; “– –” flashes, then “no” appears in the display if no CD is loaded.

2. Press ) PUSH to open the CD door.

3. Place a CD into the tray with the label facing up.

4. Close the CD door. Then the total number of tracks appears.

5. To remove the CD, press ) PUSH, grasp the CD by its edges, and carefully pull it out.

VOLUME – Turn the volume knob to increase or decrease the volume to desired level.

HBS – Press so that the HBS indicator lights.You can enjoy powerful bass sound with the Hyper-Bass Sound

effect.

STOP

SKIP/SEARCH-UP

(forward)

SKIP/SEARCH-DOWN

(backward)

Caution ––

OFF switch!

Disconnect the mains plug to shut the power off completely. The switch in any position does not disconnect

the mains line. The power cannot be remote controlled.

PROGRAM

REPEAT

PROGRAM

REPEAT

POWER OFF – Move FUNCTION to OFF/TAPE with no cassette button pressed, to turn the unit off.

CAUTION

PLAYING A CD

Press PLAY/PAUSE

in the display.

Note: Press PLAY/PAUSE

display. Press PLAY/PAUSE

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

USING THE RADIO

TUNING IN RADIO STATIONS

Move FUNCTION to TUNER to turn the radio on.

Set BAND to AM or FM.

Tune in desired station by turning the TUNING knob.

To turn off the radio, move FUNCTION to OFF/TAPE.

to play all the tracks in order starting with track 1. The current track number appears

TROUBLESHOOTING TIPS

to temporarily stop the CD. The

again to resume playing the CD.

indicator and the track number flash in the

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

CAUTION: Do not open the top cover. There are no user serviceable parts inside

the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or

defeated. Avoid direct exposure to beam.

•

Problem

Solution

•

Adjust VOLUME to a comfortable level.

Press STOP 7 to stop playing the CD. Wait a few seconds for the CD to stop turning, then press ) PUSH to

open the CD compartment door and remove the CD.

• Make sure power cord is securely plugged into the AC power outlet (or that

the batteries are fresh).

• Unplug the unit for a moment, and then plug it back in again.

• Check the outlet by plugging in another device.

System doesn’t turn on.

BEAT CUT/FM MODE SWITCH

When recording an AM broadcast

AUTOMATIC SEARCH

•

• Adjust volume setting.

• Make sure you have selected the correct function: CD, TAPE, or TUNER

and the headphones are disconnected.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.

When recording an AM broadcast, beats may occur. If this happens, set the switch

to “1” or “2.”

Changing the FM reception mode

When an FM stereo broadcast is hard to receive or noisy, set the switch to

“MONO.”

Reception improves.

Automatic search lets you quickly locate the beginning of any track on the CD, including the track currently

playing. If the CD is playing:

No sound

BEAT CUT

•

Press

beginning of the previous track.

Press (skip/search) to skip to the beginning of the next track.

(skip/search) once to return to the beginning of the current track, press twice to return to the

CAUTION - INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS

DEFEATED. AVOID EXPOSURE TO BEAM.

• Adjust the FM telescopic antenna for better FM reception.

• Rotate the unit to achieve better AM reception.

• Try turning off electrical appliances near the unit, such as TV, hair dryers,

vacuum cleaners, or fluorrescent lights.

STEREO

MONO

Poor radio reception

FM MODE

VORSICHT ! UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL

GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG

If the CD is stopped, repeatedly press

of the track you want to play, then press PLAY/PAUSE

(skip/search) or

(skip/search) until the display shows the number

. The CD player starts playing the selected track.

ÜBERBRÜCKT IST. NICHT DEM STRAHL AUSSETZEN!

To restore the stereo effect, switch to “STEREO.”

• Make sure the tray contains a CD.

VARNING - OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH

SPÄRR ÄR URKOPPLAD STRÅLEN ÄR FARLIG.

TRACK SEARCH

• Make sure the CD’s label is facing up.

• Make sure that pause mode is not activated.

• Make sure CD function is selected.

CD doesn’t play.

CD sound skips.

USING THE TAPE

•

In play mode, press and hold

(skip/search) to move forward through a track at high speed.

(skip/search) to move backward through a track at high speed.

ADVARSEL - USYNLIG LASERSTRÅLING VED ÅBNING NÅR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ

UDSÆTTELSE FOR STRÅLING.

• Clean the CD (as explained in “CARE AND MAINTENANCE”).

• Check CD for warping, scratches, or other damage.

• Check for vibration or shock that may affect the unit; move system if

necessary.

REPEAT

The REPEAT button allows you to repeat one track (REP 1) or all tracks (REP ALL). To scroll through the

choices, continuously press and release REPEAT and check the display to see which choice you have selected.

The following chart illustrates how REPEAT works in various modes.

Caution: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

• Inspect the recording head and clean it if necessary.

• Demagnetize recording head (as explained in “CARE AND

MAINTENANCE”).

Distorted or noisy

recordings

PAUSE – Press to interrupt tape play or record mode. Press a second time to resume tape play or tape record

NORMAL

REP 1

REP ALL

Front:

mode.

No obstructions and open spacing.

Sides/ Top/ Back:

No obstructions should be placed in the areas shown by the dimensions below.

Bottom:

STOP/EJECT

– Press to stop the current tape activity, or to open the cassette compartment door when no

buttons are active.

RANDOM

Press RANDOM so that “RAND” appears in the display.Start play by pressing PLAY/PAUSE

, and the tracks

SPECIFICATION

– In stop mode, press to advance the tape toward the end. (When the tape reaches the end, press

STOP/EJECT to release the depressed button.)

– In stop mode, press to rewind the tape toward the beginning. (When the tape reaches the end, press

STOP/EJECT to release the depressed button.)

are played in random order.

To quit random play, press RANDOM again.

CD player

CD capacity

Dynamic range

Signal-to-noise ratio : 75 dB

Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a

height of 10 cm or more.

General

Speaker

Power output

REW

: 1 CD

: 60 dB

: 9 cm cone × 2 (4 Ω)

: 4 W (2 W + 2 W) at 4 Ω

(10% THD) (IEC268-3)

: PHONES × 1 (∅ 3.5 mm,

stereo)

: AC 230 V Ó, 50 Hz

DC 9 V (“R20 (SUM-1)/D

(13D)” × 6)

PROGRAMMING

Press PROGRAM to enter program edit mode.

PLAY

REC

– Press to play cassettes.

– Press to record from the radio or CD player.

Front view

Side view

15 cm

“00” and “PROG” will flash in the display. Press

(skip/search) or

(skip/search) to select the track

Output terminals

Power supply

number and press PROGRAM to store the number in program place. You can repeat these steps to program up

to 20 tracks. Note that programming more than 20 tracks will overwrite the tracks already programmed.

During program play, “PROG”lights steadily.To confirm the program order, press PROGRAM in stop mode.Each

time you press PROGRAM, the program number appears, then the corresponding track number flashes in order

from the first programmed track.

15 cm

PLAYING A CASSETTE TAPE

1. Move FUNCTION to OFF/TAPE.

15 cm

Tuner

Frequency ranges

15 cm

: FM 88 - 108 MHz

: AM 540 - 1 600 kHz

: Telescopic antenna for FM

Ferrite core antenna for AM

2. Press STOP/EJECT

to open the cassette compartment door.

10 cm

3. Insert a cassette tape into the compartment with the exposed part of the tape facing up and the side you want

to play facing toward you.

4. Close the door securely.

Antenna

Power consumption : 12 W (at operation), 3 W (on

standby)

To clear the entire program in the memory, turn the unit off, or open the CD door.

Dimensions

: 420 mm (W) × 178 mm (H) ×

249 mm (D)

: Approx. 3.2 kg (without

batteries)

5. Press REW

6. Press PLAY

or FF

to move the tape to the desired starting point.

This unit has been designed only to play back the following CDs.

to begin playing the tape. The cassette tape plays until it reaches the end of the side, then it

Cassette deck section

Frequency response : 60 Hz - 10 000 Hz

•

Digital audio CD

Recordable digital audio CD (CD-R)

Rewritable digital audio CD (CD-RW)

Mass

automatically stops.

Wow and flutter

: 0.15% (WRMS)

RECORDING ON CASSETTE TAPES

You can record from the radio or the CD player.

For best recording, use normal bias tape.

Accessories provided : AC power cord × 1

Remote control unit × 1

Batteries for the remote

control unit R03 (UM-4)/AAA

(24F) × 2

When playing a CD-R or CD-RW

You can play back finalized CD-R or CD-RW recorded in music CD format. (If a CD-RW has been recorded in a

different format, erase all the data on the CD-RW completely before recording on it.)

•

It may be unlawful to record or play back copyrighted material without the consent of the copyright

owner.

•

You can play back CD-R or CD-RW like an audio CD.

Some CD-R or CD-RW may not be played back on this unit because of their disc characteristics, damage or

stain on them, or if the player lens is dirty.

ERASE PROTECTION

•

The reflection factor of CD-RW is lower than that of other CDs, possibly causing CD-RW to take longer time

to read.

CD-R and CD-RW of MP3 format cannot be played back.

When you record new material, the cassette deck records over what-

ever is on a tape. To protect a tape from accidental erasure, break

off one or both plastic tabs (one for each tape side) on the top of the

cassette tape. If you decide later to record on the tape, seal the

hole with a piece of cellophane tape.

Design and specifications are subject to change without notice.

Caution for DualDisc playback

The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore,

the use of Non-DVD side of a DualDisc on this product may not be recommended.

WARNING

A little bit of slack in your tape can cause scratches on the tape, or worse yet, the tape

could break. If you notice some slack in the tape, use a pencil to tighten it up before you

insert it in the tape deck.

TIP

The use of tapes longer than 120 minutes is not recommended, since characteristic deterioration may occur and

these tapes easily jam in the pinch-roller and the capstan.

Download from Www.Somanuals.com. All Manuals Search And Download.

ADJUSTING THE SOUND

Turn the VOLUME knob (or press VOLUME + / – button on the remote control unit) to increase or decrease

the volume to desired level. The volume level can be adjusted in 31 steps from “00” to “30”.

FIRST THINGS

NAMES OF PARTS AND CONTROLS

ENGLISH

This portable system operates on battery or AC power.

Top and front sides:

Main unit

•

Turning off the sound temporarily

During playback, press MUTING to turn the sound off. The MUTING indicator appears in the display

window. Press it again to restore the sound.

CD PORTABLE SYSTEM

BEAT CUT switch

PHONES jack

FM telecscopic antenna

RC-EX26B

2 3

4 5

6 7 8

Reinforcing the bass sound

Press and hold HBS/PRESET EQ so that the HBS indicator appears in the display window. You can

enjoy powerful bass sound with the Hyper-Bass Sound effect.

/ON

DBY

STAN

MUT

ING

PROGR

CLOCK

AM/

Supplied power cord

PUSH

AC outlet

Selecting the sound mode

You can select one of the 5 preset sound modes.

Press HBS/PRESET EQ repeatedly until the indicator for the sound mode you want appears in the

display window.

Battery compartment

APE

RANDOM

CD REPEA

Y/P

PLA

INSERTING BATTERIES

REMOTE

SENSOR

DISPLAY

Open the battery compartment cover.

Pull the battery compartment cover toward you while pressing the sections marked by the arrows.

CLASSIC: Enriched sound with fine treble and ample bass.

ROCK : Powerful sound emphasizing treble and bass.

POP : More presence in the vocals and midrange.

JAZZ : Accented lower frequencies for jazz-type music.

FLAT : Equalizer effect is canceled.

Insert six R20 (SUM-1)/D (13D)-size batteries. (not supplied)

Be sure to insert the batteries with the (+) and (–) terminals positioned correctly.

10 11 12 13 14 15

USING THE RADIO

VOLUME knob

STANDBY/ON

PRESET – button

TAPE button

CD/RANDOM button

TUNER/BAND button

TUNING IN RADIO STATIONS

button

Press TUNER/BAND to enter the tuner mode.

INSTRUCTIONS

R20 (SUM-1)/D (13D)-size batteries

Press TUNER/BAND to select the band, FM or AM.

Press and hold 4 or ¢ for more than 1 second.

The unit starts searching and stops when a station of sufficient signal strength is tuned in.

If you press 4 or ¢ briefly and repeatedly, the frequency changes step by step.

PRESET + / CD REPEAT button

Tape operation buttons

PAUSE 8 button

10 REMOTE SENSOR

11 Display window

12 Cassette deck

13 DISPLAY button

14 4 button

Replace the battery compartment cover.

Thank you for purchasing this JVC product.

STOP/EJECT § button

FF 1 button

Please read these instructions carefully before starting operation to be

sure to obtain optimum performance and a longer service life from the

unit.

Inserting Batteries into the Remote Control Unit:

Changing the FM reception mode

When an FM stereo broadcast is hard to receive or noisy, press FM MODE so that the MONO indicator

appears in the display window.

To restore the stereo effect, press FM MODE again so that the MONO indicator goes off.

The MONO will be cancelled also when changing the station.

REW ¡ button

Match the polarity (+ and –) of the batteries. R03 (UM4)/AAA (24F) ×2 (supplied)

¢ button

PLAY/PAUSE 6 button

STOP 7 button

LVT1382-009A [B]

PLAY 2 button

0205NSMBICORI

REC ÷ button

CD door

15 HBS/PRESET EQ button

FM MODE button

MUTING button

PROGRAM/CLOCK SET button

SAFETY PRECAUTIONS

PRESETTING STATIONS

You can preset 10 FM and 10 AM stations.

IMPORTANT for the U.K.

Press TUNER/BAND to select the band, FM or AM.

Press 4 or ¢ to tune in the station you want to preset.

Press PROGRAM/CLOCK SET.

Names of buttons:

Remote control unit

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power

points in your home or the cable is too short to reach a power point, then obtain an appropriate

safety approved extension lead or consult your dealer.

Note: The battery power will be switched off when you plug the power cord into the Ó AC

IN jack on the unit.

The PROG indicator starts blinking in the display window.

TUNER

PROG

BE SURE to replace the fuse only with an identical approved type, as originally fitted.

CAUTION:

MHz

STANDBY/ON

DISPLAY

If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immedi-

ately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

To avoid battery leakage or explosion, handle batteries properly.

• If you are not going to use your system for a month or more, remove the batteries from the battery

compartment.

• Dispose of batteries in the proper manner, according to federal, state, and local regulations.

• Do not mix with different battery types or with new and old ones, or do not attempt to charge a

battery not intended to be recharged.

TUNER/

BAND

CD/

RANDOM

TAPE

CD PLAY

/PAUSE

If this product is not supplied fitted with a mains plug then follow the instructions given below:

INTRO

STOP

Press PRESET + /CD REPEAT or PRESET – to select the preset number while the PROG indicator

is blinking.

FM MODE

IMPORTANT.

HBS/

PRESET EQ

CD REPEAT/

DO NOT make any connection to the terminal which is marked with the letter E or by the safety

earth symbol or coloured green or green-and-yellow.

TUNER

PROG

PRESET

–

VOLUME

MUTING

• Discard leaky batteries immediately. Leaking batteries can cause skin burns or other personal injury.

–

MHz

Preset number

The wires in the mains lead on this product are coloured in accordance with the following code:

Blue :

Brown : Live

Neutral

SUPPRLYING AC POWER

Plug the power cord into the Ó AC IN jack on the back of the unit, and into an AC power outlet.

Note: To switch off the system completely, unplug the power cord.

Press PROGRAM/CLOCK SET while the PROG indicator is blinking.

The tuned station in step 2 is stored in the preset number selected in step 4. Storing a new station on a

used number erases the previously stored one.

As these colours may not correspond with the coloured markings identifying the terminals in your

plug proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the letter

N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter

L or coloured red.

Repeat steps 2 to 5 to preset other stations, using different preset numbers.

CAUTIONS:

1. ONLY USE JVC POWER CORD PROVIDED WITH THIS UNIT TO AVOID MALFUNCTION OR

DAMAGE TO THE UNIT. REMOVE BATTERIES WHEN USING THE POWER CORD.

2. BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN

THE UNIT IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.

STANDBY/ON

button

DISPLAY button

STOP button

CD PLAY/PAUSE button

4 button

¢ button

VOLUME + button

VOLUME – button

HBS/PRESET EQ button

MUTING button

Tuning in a preset station

CD/RANDOM button

TUNER/BAND button

TAPE button

INTRO button

FM MODE button

Press TUNER/BAND to select the band, FM or AM.

Press PRESET + /CD REPEAT or PRESET – repeatedly until the desired preset number appears.

IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.

Notes:

•

USING HEADPHONES

Connect commercially available headphones to the PHONES jack on the rear of the main unit. While the

headphones are connected, the speakers do not produce any sound. Before connecting the headphones,

make sure to turn down the sound volume.

Caution ––

STANDBY/ON switch!

In some cases, test frequencies have been already memorized for the tuner since the factory examined

the tuner preset function before shipment. This is not a malfunction. You can preset the stations you

want into memory by following the presetting method.

If you unplug the AC power cord or if a power failure occurs, the preset stations will be erased in a few

days. If this happens, preset the stations again.

PRESET + /CD REPEAT button

PRESET – button

Disconnect the mains plug to shut the power off completely. The

STANDBY/ON switch in any

position does not disconnect the mains line. The power can be remote controlled.

•

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

ANTENNAS

The AM antenna is built in, so adjusting the position of the unit may help AM reception. The FM telescopic

antenna on the back of the unit can be extended and rotated for better FM reception.

GENERAL CONTROLS

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

STANDBY/ON

- Press to turn on/off the unit.

The display window lights up when the unit is turned on. (Note, however, that the display window does not

light even when the unit is turned on if the unit is operated on batteries.)

CAUTION: Do not open the top cover. There are no user serviceable parts inside the

unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or

defeated. Avoid direct exposure to beam.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.

SETTING THE CLOCK

Press DISPLAY.

The clock flashes on the display window.

CAUTION -

INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS

DEFEATED. AVOID EXPOSURE TO BEAM.

Press and hold PROGRAM/CLOCK SET for more than 2 seconds.

The hour digits start flashing.

VORSICHT !

UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL

GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG

ÜBERBRÜCKT IST. NICHT DEM STRAHL AUSSETZEN!

VARNING -

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH

SPÄRR ÄR URKOPPLAD STRÅLEN ÄR FARLIG.

ADVARSEL -

USYNLIG LASERSTRÅLING VED ÅBNING NÅR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ

UDSÆTTELSE FOR STRÅLING.

Press 4 or ¢ to adjust the hour, then press PROGRAM/CLOCK SET.

The minute digits start flashing.

Caution: Proper Ventilation

Front view

To avoid risk of electric shock and fire, and to prevent damage, locate

15 cm

the apparatus as follows:

Press 4 or ¢ adjust the minutes, then press PROGRAM/CLOCK SET.

Front:

No obstructions and open spacing.

Sides/ Top/ Back:

No obstructions should be placed in the areas shown in the

illusutrations on the right.

Notes:

10 cm

•

If there is a power failure, the clock loses the setting and is reset to “0:00.” The clock indication will keep

15 cm

flashing until you set the clock again.

Side view

•

You can also set the clock when the unit is in STANDBY mode. In this case, follow the procedures from

step 2.

15 cm

Bottom:

15 cm

Place on the level surface. Maintain an adequate air path for

ventilation by placing on a stand with a height of 10 cm or more.

To show the clock when CD or tuner is selected.

10 cm

Press DISPLAY.

Each time you press the button, the display changes the clock indication and the normal indication alternately.

(Operating the unit while clock indication is displayed changes the display to the normal indication.)

Download from Www.Somanuals.com. All Manuals Search And Download.

PROGRAMMING

CLEANING THE TAPE HEADS

USING THE TAPE

USING THE CD

Press CD/RANDOM to enter CD mode.

Clean the heads after every 10 hours of use with a wet-type head cleaning tape (available at electronic and

audio shops).

Press PROGRAM/CLOCK SET in stop mode.

The PROG indicator starts blinking in the display window.

|Forward direction

THINGS TO KNOW BEFORE PLAYING CDs

Pinch roller

PROG

Playable CDs:

Capstan

Only CDs bearing these marks can be used with this system.

Erasure head

Head

Press 4 or ¢ to select a desired track to be programmed while the PROG indicator is blinking.

Recordable

ReWritable

PROG

This unit has been designed only to play back the following CDs.

Track to be programmed

•

Digital audio CD

Recordable digital audio CD (CD-R)

Rewritable digital audio CD (CD-RW)

Press PROGRAM/CLOCK SET while the PROG indicator is blinking.

Repeat steps 3 and 4 to program other tracks.

Press PLAY/PAUSE 3/8 while the PROG indicator is blinking.

The tracks are played in the order you have programmed.

PAUSE 8 – Press to interrupt tape play or record mode. Press a second time to resume tape play or tape

record mode.

When playing a CD-R or CD-RW

You can play back finalized CD-R or CD-RW recorded in music CD format. (If a CD-RW has been

recorded in a different format, erase all the data on the CD-RW completely before recording on it.)

STOP/EJECT § – Press to stop the current tape activity, or to open the cassette compartment door

when no buttons are active.

To demagnetize the head

Turn off the unit, and use a head demagnetizer (available at electronic and audio shops).

FF 1 – In stop mode, press to advance the tape toward the end. (When the tape reaches the end, press

•

You can play back CD-R or CD-RW like an audio CD.

Some CD-R or CD-RW may not be played back on this unit because of their disc characteristics,

damage or stain on them, or if the player lens is dirty.

The reflection factor of CD-RW is lower than that of other CDs, possibly causing CD-RW to take longer

time to read.

CD-R and CD-RW of MP3 format cannot be played back.

Stopping programmed playback

Press STOP 7. The PROG indicator goes off and the unit exits from programmed playback.

STOP/EJECT § to release the depressed button.)

REW ¡ – In stop mode, press to rewind the tape toward the beginning. (When the tape reaches the end,

press STOP/EJECT § to release the depressed button.)

TROUBLESHOOTING TIPS

•

Checking the program contents

Before starting programmed playback, press PROGRAM/CLOCK SET.

Each time you press the button, the programmed tracks are shown in the display window.

PLAY 2 – Press to play cassettes.

REC ÷ – Press to record from the radio or CD player.

Problem

Solution

PLAYING A CASSETTE TAPE

1. Press TAPE to enter the tape mode.

2. Press STOP/EJECT § to open the cassette compartment door.

3. Load a cassete. Use only a type-I normal tape.

4. Close the door securely.

5. Press PLAY 2 to begin playing the tape. The cassette tape plays until it reaches the end of the side,

then it automatically stops.

• Make sure the power cord is securely plugged into the AC power

outlet (or that the batteries are fresh).

• Unplug the unit for a moment, and then plug it back in again.

• Check the outlet by plugging in another device.

Caution for DualDisc playback

The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard.

Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.

Adding tracks in the program

System does not turn on.

Press PROGRAM/CLOCK SET repeatedly until “00” appears as a track number.

Press 4 or ¢ to select a new track number, then press PROGRAM/CLOCK SET.

• Adjust the volume setting.

• Make sure you have selected the correct function: CD, TAPE, or

TUNER and the headphones are disconnected.

Editing the program

STANDBY/ON

CD door

) PUSH

No sound

Press PROGRAM/CLOCK SET repeatedly until the program number you want to edit appears.

Press 4 or ¢ to select a new track number, then press PROGRAM/CLOCK SET.

4 (skip/search

BY/ON

STAND

backward)

• Adjust the FM telescopic antenna for better FM reception.

• Rotate the unit to achieve better AM reception.

• Try turning off electrical appliances near the unit, such as TV, hair

dryers, vacuum cleaners, or fluorrescent lights.

TIN

FM MODE

PROGRAM/

CLOCK SET

¢ (skip/search

forward)

PROGRA

Fast-winding a tape

Press REW ¡ or FF 1.

When the tape reaches the end, press STOP/EJECT § to release REW ¡ or FF 1.

Poor radio reception

CLOCK

Erasing the entire program in the memory

Press PROGRAM/CLOCK SET so that the PROG indicator blinks, and press STOP 7 while the PROG

indicator blinks.

HBS/

PRESET

PUSH

CD REPEAT

RESET

APE

RANDOM

• Make sure the tray contains a CD.

EPEA

The stored program is also cleared when the CD door is opened.

CD/RANDOM

STOP 7

REMOTE

SENSOR

DISPLAY

• Make sure the CD’s label is facing up.

• Make sure that pause mode is not activated.

• Make sure the CD function is selected.

CD does not play.

CD sound skips.

RECORDING ON CASSETTE TAPES

You can record from the radio or the CD player.

Note:

PLAY/PAUSE 6

You can program up to 20 tracks in any desired order.The 21st program will overwrite the program number

“01”.

• Clean the CD (as explained in “CARE AND MAINTENANCE”).

• Check the CD for warping, scratches, or other damage.

• Check for vibration or shock that may affect the unit; move system if

necessary.

•

It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs

without the consent of the owner of copyright in the sound or video recording, broadcast or

cable program and in any literary, dramatic, musical, or artistic work embodied therein.

The recording level is automatically set correctly, so it is not affected by the other sound settings.Thus,

during recording you can adjust the sound you are actually listening to without affecting the recording

level.

INTRO PLAYBACK

Every track or every programmed track of a CD can be played for the beginning ten seconds.

STANDBY/ON

DISPLAY

TAPE

STOP

• Inspect the recording head and clean it if necessary.

• Demagnetize recording head (as explained in “CARE AND

MAINTENANCE”).

Distorted or noisy

recordings

TUNER/

BAND

CD/

RANDOM

CD/RANDOM

INTRO

CD PLAY

/PAUSE

INTRO

STOP

Press INTRO on the remote control unit. The INTRO indicator appears in the display window and intro

playback starts.To use intro playback for programmed and random playback, press the button after starting

playback.

CD PLAY/PAUSE

If recordings you have made have excessive noise or static, the unit may be too close to a TV. Increase

the distance between the TV and the unit.

FM MODE

HBS/

PRESET EQ

CD REPEAT/

VOLUME

–

CD REPEAT

Resetting the unit

PRESET

–

MUTING

•

You can only use type I tape for recording.

DO NOT turn off the unit while playing back or recording a tape. The cassette deck or tapes may be

damaged.

To quit intro playback, press INTRO again.

If “TROUBLESHOOTING TIPS” does not eliminate malfunctioning (failure to operate or display properly,

etc.), press the RESET button on the rear of the unit with something having a sharp point, while the unit is

turned on.

•

DO NOT use type II and type IV tapes since the unit is not compatible with such tapes.

The use of C-120 or longer tape is not recommended, since characteristic deterioration may occur and

this tape easily jams in the pinch rollers and the capstans.

CARE AND MAINTENANCE

CLEANING THE EXTERIOR

To protect your recordings

Cassettes have two small tabs on the back to protect against unexpected erasure or re-recording.

To protect your recording, remove these tabs.

• Disconnect the system from AC power before cleaning the exterior of the unit with a soft dry cloth.

LOADING A CD

Sharp point

HANDLING DISCS

1. Press CD/RANDOM; “00 00:00” flashes, then “no disc” appears in the display if no CD is loaded.

2. Press ) PUSH to open the CD door.

3. Place a CD into the tray with the label facing up.

4. Close the CD door. Then the total number of tracks and total playing time appear.

5. To remove the CD, press ) PUSH, grasp the CD by its edges, and carefully pull it out.

To re-record on a protected tape, cover the holes with adhesive tape.

Note:

•

Remove the disc from its case by holding it at the edge while pressing the

center hole lightly.

Resetting causes the unit to restore its factory default settings and results in all the settings made by the

user being deleted.

•

Do not touch the shiny surface of the disc, or bend the disc.

Put the disc back in its case after use to prevent warping.

PLAYING A CD

Adhesive tape

Press PLAY/PAUSE 6 to play all the tracks in order starting with track 1.

The current track number and elapsed playing time appear in the display.

Note: Press PLAY/PAUSE 6 to temporarily stop the CD.The elapsed playing time flashes in the display.

Press PLAY/PAUSE 6 again to resume playing the CD.

SPECIFICATIONS

RECORDING FROM THE RADIO

1. Insert a cassette tape into the cassette deck and close the door.

2. Press TUNER/BAND and select a radio station.

3. Press REC ÷ to begin recording. REC ÷ and PLAY 2 are locked down.

4. Press STOP/EJECT § to stop recording.

CD player

•

Be careful not to scratch the surface of the disc when placing it back in its

case.

Avoid exposure to direct sunlight, temperature extremes, and moisture.

CD capacity

Dynamic range

Signal-to-noise ratio

: 1 CD

: 60 dB

: 75 dB

•

Adjust VOLUME to a comfortable level.

Press STOP 7 to stop playing the CD. Wait a few seconds for the CD to stop turning, then press )

PUSH to open the CD door and remove the CD.

Tuner

Frequency ranges

AUTOMATIC SEARCH

Automatic search quickly locates the beginning of any track on the CD, including the track currently playing.

If the CD is playing:

When recording an AM broadcast

When recording an AM broadcast, beats may occur. If this happens, set

the BEAT CUT switch to “1” or “2.”

BEAT CUT

: FM 87.5 - 108.0 MHz

: AM 522 - 1 629 kHz

: Telescopic antenna for FM

Ferrite core antenna for AM

Antenna

•

Press 4 once to return to the beginning of the current track, press twice to return to the beginning of

the previous track.

Press ¢ to skip to the beginning of the next track.

To clean the disc

TIP

•

Wipe the disc with a soft cloth in a straight line from center to edge.

DO NOT use any solvent-such as conventional record cleaner, spray, thin-

ner, or benzine-to clean the disc.

Cassette deck section

Frequency response

Wow and flutter

To temporarily pause the recording, press PAUSE 8 on the cassette deck.Press PAUSE 8 again to resume

If the CD is stopped, repeatedly press 4 or ¢ until the display shows the number of the track you want

to play, then press PLAY/PAUSE 6. The CD player starts playing the selected track.

: 60 Hz - 10 000 Hz

: 0.15% (WRMS)

recording.

SYNCHRONIZED RECORDING FROM A CD

1. Insert a cassette tape into the cassette deck and close the door.

2. Press CD/RANDOM.

3. Place a CD you want to record into CD compartment.

4. Select the track you want to record by pressing 4 or ¢.

5. Press REC ÷ to start synchronized recording.

Notes:

TRACK SEARCH

General

Speaker

Power output

Output terminals

Power supply

•

In play mode, press and hold ¢ to move forward through a track at high speed.

In play mode, press and hold 4 to move backward through a track at high speed.

: 9 cm cone × 2 (4 Ω)

: 4 W (2 W + 2 W) at 4 Ω (10% THD) (IEC268-3)

: PHONES × 1 (∅ 3.5 mm, stereo)

: AC 230 V Ó, 50 Hz

DC 9 V (“R20 (SUM-1)/D (13D)” × 6)

: 13 W (at operation), 3 W (on standby)

: 420 mm (W) × 178 mm (H) × 249 mm (D)

: Approx. 3.2 kg (without batteries)

: AC power cord × 1

HANDLING CASSETTE TAPES

REPEAT

The CD REPEAT button repeats one track (REPEAT 1) or all tracks (REPEAT ALL). To scroll through the

choices, continuously press and release CD REPEAT, and check the display to see which choice you have

selected. The following chart illustrates how REPEAT works in various modes.

•

If the tape is loose in its cassette, take up the slack by inserting a pencil in one of

the reels and rotating.

If the tape is loose, it may get stretched, cut, or caught in the cassette.

Power consumption

Dimensions

Mass

•

When the tape reaches the end, the CD playback enters in pause.

To continue recording:

To continue the CD playback:

To stop the CD playback:

turn over the tape and press REC ÷.

NORMAL

REPEAT ALL

REPEAT 1

press PLAY/PAUSE 6.

press STOP 7.

Accessories provided

RANDOM

Remote control unit × 1

Batteries for the remote control unit R03 (UM-4)/AAA (24F) × 2

•

When the CD playback stops, the cassette tape continues running.

•

Be careful not to touch the tape surface.

To stop the cassette tape, press STOP/EJECT §.

TIP

In CD mode, press CD/RANDOM. The RANDOM indicator appears in the display and random playback

starts.

To quit random playback, press CD/RANDOM again.

Using the PAUSE 8 button on the cassette deck instead of the STOP/EJECT § button to momentarily

Design and specifications are subject to change without notice.

interrupt recording gives you a much clearer sound recording.

ERASING

Avoid storing tapes in any of the following places:

- In dusty places

- In direct sunlight or heat

- In moist areas

- On a TV or speaker

- Near a magnet

When recording on a pre-recorded tape, the previous recording is erased and only the new recording is

heard next time the tape is played back.

Erasing a recording on a tape without making a new recording

1. Press TAPE to enter the tape mode.

2 . Press REC ÷ to start recording.

Download from Www.Somanuals.com. All Manuals Search And Download.

ADJUSTING THE SOUND

Turn the VOLUME knob (or pressVOLUME + / – button on the remote control unit) to increase or decrease

the volume to desired level. The volume level can be adjusted in 31 steps from “00” to “30”.

FIRST THINGS

NAMES OF PARTS AND CONTROLS

ENGLISH

This portable system operates on battery or AC power.

Top and front sides:

Main unit

•

Turning off the sound temporarily

During playback, press MUTING to turn the sound off. The MUTING indicator appears in the display

window. Press it again to restore the sound.

CD PORTABLE SYSTEM

BEAT CUT switch

PHONES jack

FM telecscopic antenna

RC-EX26B

2 3

4 5

6 7 8

Reinforcing the bass sound

Press and hold HBS/PRESET EQ so that the HBS indicator appears in the display window. You can

enjoy powerful bass sound with the Hyper-Bass Sound effect.

DBY/ON

STAN

MUTING

PROGRAM

CLOCK

SET

Supplied power cord

PRESE

PUSH

AC outlet

Selecting the sound mode

You can select one of the 5 preset sound modes.

Press HBS/PRESET EQ repeatedly until the indicator for the sound mode you want appears in the

display window.

Battery compartment

PRESET

APE

RANDOM

USE

EPEA

Y/P

PLA

INSERTING BATTERIES

REMOTE

SENSOR

DISPLAY

Open the battery compartment cover.

Pull the battery compartment cover toward you while pressing the sections marked by the arrows.

CLASSIC: Enriched sound with fine treble and ample bass.

ROCK : Powerful sound emphasizing treble and bass.

POP : More presence in the vocals and midrange.

JAZZ : Accented lower frequencies for jazz-type music.

FLAT : Equalizer effect is canceled.

Insert six R20 (SUM-1)/D (13D)-size batteries. (not supplied)

Be sure to insert the batteries with the (+) and (–) terminals positioned correctly.

10 11 12 13 14 15

USING THE RADIO

VOLUME knob

STANDBY/ON

PRESET – button

TAPE button

CD/RANDOM button

TUNER/BAND button

TUNING IN RADIO STATIONS

button

Press TUNER/BAND to enter the tuner mode.

INSTRUCTIONS

R20 (SUM-1)/D (13D)-size batteries

Press TUNER/BAND to select the band, FM or AM.

Press and hold 4 or ¢ for more than 1 second.

The unit starts searching and stops when a station of sufficient signal strength is tuned in.

If you press 4 or ¢ briefly and repeatedly, the frequency changes step by step.

PRESET + / CD REPEAT button

Tape operation buttons

PAUSE 8 button

10 REMOTE SENSOR

11 Display window

12 Cassette deck

13 DISPLAY button

14 4 button

Replace the battery compartment cover.

Thank you for purchasing this JVC product.

STOP/EJECT § button

FF 1 button

Please read these instructions carefully before starting operation to be

sure to obtain optimum performance and a longer service life from the

unit.

Inserting Batteries into the Remote Control Unit:

Changing the FM reception mode

When an FM stereo broadcast is hard to receive or noisy, press FM MODE so that the MONO indicator

appears in the display window.

To restore the stereo effect, press FM MODE again so that the MONO indicator goes off.

The MONO will be cancelled also when changing the station.

REW ¡ button

Match the polarity (+ and –) of the batteries. R03 (UM4)/AAA (24F) ×2 (supplied)

¢ button

PLAY/PAUSE 6 button

STOP 7 button

LVT1382-010A [E/EN]

PLAY 2 button

0205NSMBICORI

REC ÷ button

CD door

15 HBS/PRESET EQ button

FM MODE button

MUTING button

PROGRAM/CLOCK SET button

SAFETY PRECAUTIONS

PRESETTING STATIONS

You can preset 10 FM and 10 AM stations.

Caution ––

STANDBY/ON switch!

Disconnect the mains plug to shut the power off completely. The

position does not disconnect the mains line. The power can be remote controlled.

Press TUNER/BAND to select the band, FM or AM.

Press 4 or ¢ to tune in the station you want to preset.

Press PROGRAM/CLOCK SET.

STANDBY/ON switch in any

Names of buttons:

Remote control unit

Note: The battery power will be switched off when you plug the power cord into the Ó AC

IN jack on the unit.

The PROG indicator starts blinking in the display window.

CAUTION

TUNER

PROG

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

CAUTION:

MHz

STANDBY/ON

DISPLAY

To avoid battery leakage or explosion, handle batteries properly.

• If you are not going to use your system for a month or more, remove the batteries from the battery

compartment.

• Dispose of batteries in the proper manner, according to federal, state, and local regulations.

• Do not mix with different battery types or with new and old ones, or do not attempt to charge a

battery not intended to be recharged.

TUNER/

BAND

CD/

RANDOM

TAPE

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

CAUTION: Do not open the top cover.There are no user serviceable parts inside the

unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or

defeated. Avoid direct exposure to beam.

CD PLAY

/PAUSE

INTRO

STOP

Press PRESET + /CD REPEAT or PRESET – to select the preset number while the PROG indicator

is blinking.

FM MODE

HBS/

PRESET EQ

CD REPEAT/

TUNER

PROG

PRESET

–

VOLUME

MUTING

• Discard leaky batteries immediately.Leaking batteries can cause skin burns or other personal injury.

–

MHz

Preset number

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.

SUPPRLYING AC POWER

Plug the power cord into the Ó AC IN jack on the back of the unit, and into an AC power outlet.

Note: To switch off the system completely, unplug the power cord.

Press PROGRAM/CLOCK SET while the PROG indicator is blinking.

The tuned station in step 2 is stored in the preset number selected in step 4. Storing a new station on a

used number erases the previously stored one.

CAUTION -

INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS

DEFEATED. AVOID EXPOSURE TO BEAM.

VORSICHT !

UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL

GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG

ÜBERBRÜCKT IST. NICHT DEM STRAHL AUSSETZEN!

Repeat steps 2 to 5 to preset other stations, using different preset numbers.

CAUTIONS:

1. ONLY USE JVC POWER CORD PROVIDED WITH THIS UNIT TO AVOID MALFUNCTION OR

DAMAGE TO THE UNIT. REMOVE BATTERIES WHEN USING THE POWER CORD.

2. BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN

THE UNIT IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.

STANDBY/ON

button

DISPLAY button

STOP button

CD PLAY/PAUSE button

4 button

¢ button

VOLUME + button

VOLUME – button

HBS/PRESET EQ button

MUTING button

Tuning in a preset station

VARNING -

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH

SPÄRR ÄR URKOPPLAD STRÅLEN ÄR FARLIG.

CD/RANDOM button

TUNER/BAND button

TAPE button

INTRO button

FM MODE button

Press TUNER/BAND to select the band, FM or AM.

Press PRESET + /CD REPEAT or PRESET – repeatedly until the desired preset number appears.

ADVARSEL -

USYNLIG LASERSTRÅLING VED ÅBNING NÅR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ

UDSÆTTELSE FOR STRÅLING.

Notes:

•

USING HEADPHONES

Connect commercially available headphones to the PHONES jack on the rear of the main unit. While the

headphones are connected, the speakers do not produce any sound. Before connecting the headphones,

make sure to turn down the sound volume.

In some cases, test frequencies have been already memorized for the tuner since the factory examined

the tuner preset function before shipment. This is not a malfunction. You can preset the stations you

want into memory by following the presetting method.

If you unplug the AC power cord or if a power failure occurs, the preset stations will be erased in a few

days. If this happens, preset the stations again.

PRESET + /CD REPEAT button

PRESET – button

Caution: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

•

Front:

ANTENNAS

No obstructions and open spacing.

Sides/ Top/ Back:

No obstructions should be placed in the areas shown by the dimensions below.

The AM antenna is built in, so adjusting the position of the unit may help AM reception.The FM telescopic

antenna on the back of the unit can be extended and rotated for better FM reception.

GENERAL CONTROLS

Bottom:

STANDBY/ON

- Press to turn on/off the unit.

Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand

with a height of 10 cm or more.

The display window lights up when the unit is turned on. (Note, however, that the display window does not

light even when the unit is turned on if the unit is operated on batteries.)

SETTING THE CLOCK

Side view

Front view

15 cm

Press DISPLAY.

15 cm

The clock flashes on the display window.

15 cm

Press and hold PROGRAM/CLOCK SET for more than 2 seconds.

The hour digits start flashing.

10 cm

Press 4 or ¢ to adjust the hour, then press PROGRAM/CLOCK SET.

The minute digits start flashing.

Press 4 or ¢ adjust the minutes, then press PROGRAM/CLOCK SET.

Notes:

•

If there is a power failure, the clock loses the setting and is reset to “0:00.”The clock indication will keep

flashing until you set the clock again.

•

You can also set the clock when the unit is in STANDBY mode. In this case, follow the procedures from

step 2.

To show the clock when CD or tuner is selected.

Press DISPLAY.

Each time you press the button, the display changes the clock indication and the normal indication alternately.

(Operating the unit while clock indication is displayed changes the display to the normal indication.)

Download from Www.Somanuals.com. All Manuals Search And Download.

PROGRAMMING

CLEANING THE TAPE HEADS

USING THE TAPE

USING THE CD

Press CD/RANDOM to enter CD mode.

Clean the heads after every 10 hours of use with a wet-type head cleaning tape (available at electronic and

audio shops).

Press PROGRAM/CLOCK SET in stop mode.

The PROG indicator starts blinking in the display window.

|Forward direction

THINGS TO KNOW BEFORE PLAYING CDs

Pinch roller

PROG

Playable CDs:

Capstan

Only CDs bearing these marks can be used with this system.

Erasure head

Head

Press 4 or ¢ to select a desired track to be programmed while the PROG indicator is blinking.

Recordable

ReWritable

PROG

This unit has been designed only to play back the following CDs.

Track to be programmed

•

Digital audio CD

Recordable digital audio CD (CD-R)

Rewritable digital audio CD (CD-RW)

Press PROGRAM/CLOCK SET while the PROG indicator is blinking.

Repeat steps 3 and 4 to program other tracks.

Press PLAY/PAUSE 3/8 while the PROG indicator is blinking.

The tracks are played in the order you have programmed.

PAUSE 8 – Press to interrupt tape play or record mode. Press a second time to resume tape play or tape

record mode.

When playing a CD-R or CD-RW

You can play back finalized CD-R or CD-RW recorded in music CD format. (If a CD-RW has been

recorded in a different format, erase all the data on the CD-RW completely before recording on it.)

STOP/EJECT § – Press to stop the current tape activity, or to open the cassette compartment door

when no buttons are active.

To demagnetize the head

Turn off the unit, and use a head demagnetizer (available at electronic and audio shops).

FF 1 – In stop mode, press to advance the tape toward the end. (When the tape reaches the end, press

•

You can play back CD-R or CD-RW like an audio CD.

Some CD-R or CD-RW may not be played back on this unit because of their disc characteristics,

damage or stain on them, or if the player lens is dirty.

The reflection factor of CD-RW is lower than that of other CDs, possibly causing CD-RW to take longer

time to read.

CD-R and CD-RW of MP3 format cannot be played back.

Stopping programmed playback

Press STOP 7. The PROG indicator goes off and the unit exits from programmed playback.

STOP/EJECT § to release the depressed button.)

REW ¡ – In stop mode, press to rewind the tape toward the beginning. (When the tape reaches the end,

press STOP/EJECT § to release the depressed button.)

TROUBLESHOOTING TIPS

•

Checking the program contents

Before starting programmed playback, press PROGRAM/CLOCK SET.

Each time you press the button, the programmed tracks are shown in the display window.

PLAY 2 – Press to play cassettes.

REC ÷ – Press to record from the radio or CD player.

Problem

Solution

PLAYING A CASSETTE TAPE

1. Press TAPE to enter the tape mode.

2. Press STOP/EJECT § to open the cassette compartment door.

3. Load a cassete. Use only a type-I normal tape.

4. Close the door securely.

5. Press PLAY 2 to begin playing the tape. The cassette tape plays until it reaches the end of the side,

then it automatically stops.

• Make sure the power cord is securely plugged into the AC power

outlet (or that the batteries are fresh).

• Unplug the unit for a moment, and then plug it back in again.

• Check the outlet by plugging in another device.

Caution for DualDisc playback

The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard.

Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.

Adding tracks in the program

System does not turn on.

Press PROGRAM/CLOCK SET repeatedly until “00” appears as a track number.

Press 4 or ¢ to select a new track number, then press PROGRAM/CLOCK SET.

• Adjust the volume setting.

• Make sure you have selected the correct function: CD, TAPE, or

TUNER and the headphones are disconnected.

Editing the program

STANDBY/ON

CD door

) PUSH

No sound

Press PROGRAM/CLOCK SET repeatedly until the program number you want to edit appears.

Press 4 or ¢ to select a new track number, then press PROGRAM/CLOCK SET.

4 (skip/search

BY/ON

STAND

backward)

• Adjust the FM telescopic antenna for better FM reception.

• Rotate the unit to achieve better AM reception.

• Try turning off electrical appliances near the unit, such as TV, hair

dryers, vacuum cleaners, or fluorrescent lights.

MUTING

HBS/

FM MODE

PROGRAM/

CLOCK SET

¢ (skip/search

forward)

PROGRAM/

CLOCK SET

Fast-winding a tape

Press REW ¡ or FF 1.

When the tape reaches the end, press STOP/EJECT § to release REW ¡ or FF 1.

Poor radio reception

Erasing the entire program in the memory

Press PROGRAM/CLOCK SET so that the PROG indicator blinks, and press STOP 7 while the PROG

indicator blinks.

PRESET

PUSH

CD REPEAT

PRESET

APE

• Make sure the tray contains a CD.

Y/P

PLA

PEA

The stored program is also cleared when the CD door is opened.

CD/RANDOM

STOP 7

REMOTE

SENSOR

DISPLAY

• Make sure the CD’s label is facing up.

• Make sure that pause mode is not activated.

• Make sure the CD function is selected.

AND

CD does not play.

CD sound skips.

RECORDING ON CASSETTE TAPES

You can record from the radio or the CD player.

Note:

PLAY/PAUSE 6

You can program up to 20 tracks in any desired order.The 21st program will overwrite the program number

“01”.

• Clean the CD (as explained in “CARE AND MAINTENANCE”).

• Check the CD for warping, scratches, or other damage.

• Check for vibration or shock that may affect the unit; move system if

necessary.

•

It may be unlawful to record or play back copyrighted material without the consent of the copyright

owner.

•

The recording level is automatically set correctly, so it is not affected by the other sound settings.Thus,

during recording you can adjust the sound you are actually listening to without affecting the recording

level.

INTRO PLAYBACK

Every track or every programmed track of a CD can be played for the beginning ten seconds.

STANDBY/ON

DISPLAY

TAPE

STOP

• Inspect the recording head and clean it if necessary.

• Demagnetize recording head (as explained in “CARE AND

MAINTENANCE”).

Distorted or noisy

recordings

TUNER/

BAND

CD/

RANDOM

CD/RANDOM

INTRO

CD PLAY

/PAUSE

•

If recordings you have made have excessive noise or static, the unit may be too close to a TV. Increase

the distance between the TV and the unit.

INTRO

STOP

Press INTRO on the remote control unit. The INTRO indicator appears in the display window and intro

playback starts.To use intro playback for programmed and random playback, press the button after starting

playback.

CD PLAY/PAUSE

FM MODE

HBS/

PRESET EQ

CD REPEAT/

VOLUME

–

•

You can only use type I tape for recording.

DO NOT turn off the unit while playing back or recording a tape. The cassette deck or tapes may be

damaged.

CD REPEAT

Resetting the unit

PRESET

–

MUTING

To quit intro playback, press INTRO again.

If “TROUBLESHOOTING TIPS” does not eliminate malfunctioning (failure to operate or display properly,

etc.), press the RESET button on the rear of the unit with something having a sharp point, while the unit is

turned on.

•

DO NOT use type II and type IV tapes since the unit is not compatible with such tapes.

The use of C-120 or longer tape is not recommended, since characteristic deterioration may occur and

this tape easily jams in the pinch rollers and the capstans.

CARE AND MAINTENANCE

To protect your recordings

Cassettes have two small tabs on the back to protect against unexpected erasure or re-recording.

To protect your recording, remove these tabs.

CLEANING THE EXTERIOR

• Disconnect the system from AC power before cleaning the exterior of the unit with a soft dry cloth.

LOADING A CD

To re-record on a protected tape, cover the holes with adhesive tape.

Sharp point

HANDLING DISCS

1. Press CD/RANDOM; “00 00:00” flashes, then “no disc” appears in the display if no CD is loaded.

2. Press ) PUSH to open the CD door.

3. Place a CD into the tray with the label facing up.

4. Close the CD door. Then the total number of tracks and total playing time appear.

5. To remove the CD, press ) PUSH, grasp the CD by its edges, and carefully pull it out.

Note:

•

Remove the disc from its case by holding it at the edge while pressing the

center hole lightly.

Resetting causes the unit to restore its factory default settings and results in all the settings made by the

user being deleted.

•

Do not touch the shiny surface of the disc, or bend the disc.

Put the disc back in its case after use to prevent warping.

Adhesive tape

PLAYING A CD

Press PLAY/PAUSE 6 to play all the tracks in order starting with track 1.

The current track number and elapsed playing time appear in the display.

Note: Press PLAY/PAUSE 6 to temporarily stop the CD.The elapsed playing time flashes in the display.

Press PLAY/PAUSE 6 again to resume playing the CD.

SPECIFICATIONS

RECORDING FROM THE RADIO

1. Insert a cassette tape into the cassette deck and close the door.

2. Press TUNER/BAND and select a radio station.

3. Press REC ÷ to begin recording. REC ÷ and PLAY 2 are locked down.

4. Press STOP/EJECT § to stop recording.

CD player

•

Be careful not to scratch the surface of the disc when placing it back in its

case.

Avoid exposure to direct sunlight, temperature extremes, and moisture.

CD capacity

Dynamic range

Signal-to-noise ratio

: 1 CD

: 60 dB

: 75 dB

•

Adjust VOLUME to a comfortable level.

Press STOP 7 to stop playing the CD. Wait a few seconds for the CD to stop turning, then press )

PUSH to open the CD door and remove the CD.

BEAT CUT

Tuner

Frequency ranges

When recording an AM broadcast

When recording an AM broadcast, beats may occur. If this happens, set

the BEAT CUT switch to “1” or “2.”

AUTOMATIC SEARCH

Automatic search quickly locates the beginning of any track on the CD, including the track currently playing.

If the CD is playing:

: FM 87.5 - 108.0 MHz

: AM 522 - 1 629 kHz

: Telescopic antenna for FM

Ferrite core antenna for AM

Antenna

•

Press 4 once to return to the beginning of the current track, press twice to return to the beginning of

the previous track.

Press ¢ to skip to the beginning of the next track.

TIP

To clean the disc

To temporarily pause the recording, press PAUSE 8 on the cassette deck.Press PAUSE 8 again to resume

•

Wipe the disc with a soft cloth in a straight line from center to edge.

DO NOT use any solvent-such as conventional record cleaner, spray, thin-

ner, or benzine-to clean the disc.

Cassette deck section

Frequency response

Wow and flutter

recording.

If the CD is stopped, repeatedly press 4 or ¢ until the display shows the number of the track you want

to play, then press PLAY/PAUSE 6. The CD player starts playing the selected track.

: 60 Hz - 10 000 Hz

: 0.15% (WRMS)

SYNCHRONIZED RECORDING FROM A CD

1. Insert a cassette tape into the cassette deck and close the door.

2. Press CD/RANDOM.

3. Place a CD you want to record into CD compartment.

4. Select the track you want to record by pressing 4 or ¢.

5. Press REC ÷ to start synchronized recording.

Notes:

TRACK SEARCH

General

Speaker

Power output

Output terminals

Power supply

•

In play mode, press and hold ¢ to move forward through a track at high speed.

In play mode, press and hold 4 to move backward through a track at high speed.

: 9 cm cone × 2 (4 Ω)

: 4 W (2 W + 2 W) at 4 Ω (10% THD) (IEC268-3)

: PHONES × 1 (∅ 3.5 mm, stereo)

: AC 230 V Ó, 50 Hz

DC 9 V (“R20 (SUM-1)/D (13D)” × 6)

: 13 W (at operation), 3 W (on standby)

: 420 mm (W) × 178 mm (H) × 249 mm (D)

: Approx. 3.2 kg (without batteries)

: AC power cord × 1

HANDLING CASSETTE TAPES

REPEAT

The CD REPEAT button repeats one track (REPEAT 1) or all tracks (REPEAT ALL). To scroll through the

choices, continuously press and release CD REPEAT, and check the display to see which choice you have

selected. The following chart illustrates how REPEAT works in various modes.

•

If the tape is loose in its cassette, take up the slack by inserting a pencil in one of

the reels and rotating.

If the tape is loose, it may get stretched, cut, or caught in the cassette.

•

When the tape reaches the end, the CD playback enters in pause.

Power consumption

Dimensions

Mass

To continue recording:

To continue the CD playback:

To stop the CD playback:

turn over the tape and press REC ÷.

press PLAY/PAUSE 6.

press STOP 7.

NORMAL

REPEAT ALL

REPEAT 1

Accessories provided

•

When the CD playback stops, the cassette tape continues running.

RANDOM

Remote control unit × 1

Batteries for the remote control unit R03 (UM-4)/AAA (24F) × 2

To stop the cassette tape, press STOP/EJECT §.

•

Be careful not to touch the tape surface.

In CD mode, press CD/RANDOM. The RANDOM indicator appears in the display and random playback

starts.

To quit random playback, press CD/RANDOM again.

TIP

Using the PAUSE 8 button on the cassette deck instead of the STOP/EJECT § button to momentarily

interrupt recording gives you a much clearer sound recording.

Design and specifications are subject to change without notice.

ERASING

When recording on a pre-recorded tape, the previous recording is erased and only the new recording is

heard next time the tape is played back.

Avoid storing tapes in any of the following places:

- In dusty places

- In direct sunlight or heat

- In moist areas

- On a TV or speaker

Erasing a recording on a tape without making a new recording

1. Press TAPE to enter the tape mode.

2 . Press REC ÷ to start recording.

- Near a magnet

Download from Www.Somanuals.com. All Manuals Search And Download.

ADJUSTING THE SOUND

Turn the VOLUME knob (or pressVOLUME + / – button on the remote control unit) to increase or decrease

the volume to desired level. The volume level can be adjusted in 31 steps from “MIN” to “MAX”.

NAMES OF PARTS AND CONTROLS

Caution: Proper Ventilation

15 cm

To avoid risk of electric shock and fire, and to prevent damage, locate

ENGLISH

Top and front sides:

Main unit

15 cm

the apparatus as follows:

•

Turning off the sound temporarily

During playback, press MUTING on the remote control unit to turn the sound off.The MUTING indicator

appears in the display window. Press it again to restore the sound.

CD PORTABLE SYSTEM

Front:

No obstructions and open spacing.

Sides/ Top/ Back:

No obstructions should be placed in the areas shown in the

illusutrations on the right.

RC-EX36S

10 cm

2 3

4 5

6 7 8

Reinforcing the bass sound

Press and hold HBS/PRESET EQ so that the HBS indicator appears in the display window. You can

enjoy powerful bass sound with the Hyper-Bass Sound effect.

15 cm

BY/ON

STA

OGRAM/

15 cm

OCK SET

Bottom:

PRESET

15 cm

PUSH

Place on the level surface. Maintain an adequate air path for

ventilation by placing on a stand with a height of 10 cm or more.

Selecting the sound mode

You can select one of the 5 preset sound modes.

10 cm

APE

RANDOM

Press HBS/PRESET EQ repeatedly until the indicator for the sound mode you want appears in the

display window.

Y/P

PLA

TUNER

REMOTE

SENSOR

DISPLAY

CLASSIC: Enriched sound with fine treble and ample bass.

ROCK : Powerful sound emphasizing treble and bass.

POP : More presence in the vocals and midrange.

JAZZ : Accented lower frequencies for jazz-type music.

FLAT : Equalizer effect is canceled.

FIRST THINGS

This portable system operates on battery or AC power.

FM telescopic antenna

PHONES jack

USING THE RADIO

10 11 12 13 14 15

TUNING IN RADIO STATIONS

PRESET UP button

TAPE button

VOLUME knob

STANDBY/ON

GROUP – button

GROUP + button

Press TUNER/BAND to enter the tuner mode.

button

Press TUNER/BAND to select the band, FM or AM.

Press and hold 4 or ¢ for more than 1 second.

The unit starts searching and stops when a station of sufficient signal strength is tuned in.

If you press 4 or ¢ briefly and repeatedly, the frequency changes step by step.

CD/RANDOM button

TUNER/BAND button

Supplied power cord

AC outlet

INSTRUCTIONS

10 REMOTE SENSOR

11 Display window

12 Cassette deck

13 DISPLAY button

14 4 button

Tape operation buttons

Battery compartment

PAUSE 8 button

Changing the FM reception mode

When an FM stereo broadcast is hard to receive or noisy, press FM MODE/BEAT CUT on the remote

control unit so that the MONO indicator appears in the display window.

To restore the stereo effect, press FM MODE/BEAT CUT again so that the MONO indicator goes off.

The FM MODE will be changed to STEREO also when changing the station.

STOP/EJECT § button

FF 1 button

Thank you for purchasing this JVC product.

Please read these instructions carefully before starting operation to be

sure to obtain optimum performance and a longer service life from the

unit.

INSERTING BATTERIES

REW ¡ button

PLAY 2 button

Open the battery compartment cover.

¢ button

Pull the battery compartment cover toward you while pressing the sections marked by the arrows.

PLAY/PAUSE 6 button

STOP 7 button

REC ÷ button

LVT1385-007A [B]

CD door

0205NSMBICORI

Insert six R20 (SUM-1)/D (13D)-size batteries. (not supplied)

Be sure to insert the batteries with the (+) and (–) terminals positioned correctly.

PRESETTING STATIONS

You can preset 20 FM and 10 AM stations.

15 HBS/PRESET EQ button

PRESET DOWN button

PROGRAM/CLOCK SET button

Press TUNER/BAND to select the band, FM or AM.

Press 4 or ¢ to tune in the station you want to preset.

Press PROGRAM/CLOCK SET.

SAFETY PRECAUTIONS

Names of buttons:

Remote control unit

The PROGRAM indicator and the preset number start blinking in the display window.

IMPORTANT for the U.K.

PROGRAM

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power

points in your home or the cable is too short to reach a power point, then obtain an appropriate

safety approved extension lead or consult your dealer.

STANDBY/ON

CD/

TUNER/

BAND

RANDOM

TAPE

MHz

FLAT

DISPLAY

R20 (SUM-1)/D (13D)-size batteries

BE SURE to replace the fuse only with an identical approved type, as originally fitted.

HBS/

PRESET EQ

OVER

Press PRESET UP or PRESET DOWN to select the preset number while the PROGRAM indicator is

blinking.

You can use the number buttons on the remote control unit to select the preset number directly.

Example: To select preset number 5, press 5. To select preset number 15, press OVER, 1, then 5.

To select preset number 20, press OVER, 2, then 0.

FM MODE

/BEAT CUT

If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immedi-

ately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

Replace the battery compartment cover.

PROGRAM/

CLOCK SET

GROUP

–

INTRO

PRESET

DOWN

REPEAT

MUTING

Inserting Batteries into the Remote Control Unit:

If this product is not supplied fitted with a mains plug then follow the instructions given below:

Match the polarity (+ and –) of the batteries. R03 (UM-4)/AAA (24F)×2 (supplied)

IMPORTANT.

VOLUME

DO NOT make any connection to the terminal which is marked with the letter E or by the safety

PROGRAM

earth symbol or coloured green or green-and-yellow.

Preset number

The wires in the mains lead on this product are coloured in accordance with the following code:

MHz

RM-SRCEX30J REMOTE CONTROL

FLAT

Blue :

Neutral

Brown : Live

Press PROGRAM/CLOCK SET while the PROGRAM indicator is blinking.

The tuned station in step 2 is stored in the preset number selected in step 4.

Storing a new station on a used number erases the previously stored one.

When the PROGRAM indicator stops blinking, the tuned station is stored in the preset number without

pressing PROGRAM/CLOCK SET.

If you use the number buttons to select the preset number in step 4, pressing PROGRAM/CLOCK SET

is not necessary in this step.

Repeat steps 2 to 5 to preset other stations, using different preset numbers.

As these colours may not correspond with the coloured markings identifying the terminals in your

plug proceed as follows:

STANDBY/ON

DISPLAY button

button

CD/RANDOM button

TUNER/BAND button

TAPE button

Number buttons

GROUP +/– buttons

VOLUME +/– buttons

Note: The battery power will be switched off when you plug the power cord into the Ó AC

The wire which is coloured blue must be connected to the terminal which is marked with the letter

HBS/PRESET EQ button

FM MODE/BEAT CUT button

PRESET UP/DOWN buttons

PROGRAM/CLOCK SET button

INTRO button

IN jack on the unit.

N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter

L or coloured red.

CAUTION:

To avoid battery leakage or explosion, handle batteries properly.

• If you are not going to use your system for a month or more, remove the batteries from the battery

compartment.

• Dispose of batteries in the proper manner, according to federal, state, and local regulations.

• Do not mix with different battery types or with new and old ones, or do not attempt to charge a

battery not intended to be recharged.

IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.

REPEAT button

MUTING button

Tuning in a preset station

Press TUNER/BAND to select the band, FM or AM.

Press PRESET UP or PRESET DOWN repeatedly until the desired preset number appears.

You can use the number buttons on the remote control unit to select the preset number directly.

Example:

To select preset number 5, press 5.

To select preset number 15, press OVER, 1, then 5.

To select preset number 20, press OVER, 2, then 0.

Caution ––

STANDBY/ON switch!

3/8 button

Disconnect the mains plug to shut the power off completely. The

position does not disconnect the mains line. The power can be remote controlled.

STANDBY/ON switch in any

4 button

¢ button

• Discard leaky batteries immediately.Leaking batteries can cause skin burns or other personal injury.

CAUTION

7 button

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

SUPPRLYING AC POWER

Plug the power cord into the Ó AC IN jack on the back of the unit, and into an AC power outlet.

Note: To switch off the system completely, unplug the power cord.

GENERAL CONTROLS

Note

IMPORTANT FOR LASER PRODUCTS

If you unplug the AC power cord or if a power failure occurs, the preset stations will be erased in a few

days. If this happens, preset the stations again.

STANDBY/ON

- Press to turn on/off the unit.

CAUTIONS:

1. CLASS 1 LASER PRODUCT

The display window lights up when the unit is turned on. (Note, however, that the display window does not

light even when the unit is turned on if the unit is operated on batteries.)

1. ONLY USE JVC POWER CORD PROVIDED WITH THIS UNIT TO AVOID MALFUNCTION OR

DAMAGE TO THE UNIT. REMOVE BATTERIES WHEN USING THE POWER CORD.

2. BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN

THE UNIT IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.

CAUTION: Do not open the top cover. There are no user serviceable parts inside

the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or

defeated. Avoid direct exposure to beam.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.

USING THE TAPE

SETTING THE CLOCK

Before operating the unit any further, first set the clock built in this unit.

The clock uses 24-hour indication.

|Forward direction

USING HEADPHONES

Connect commercially available headphones to the PHONES jack on the rear of the main unit. While the

headphones are connected, the speakers do not produce any sound. Before connecting the headphones,

make sure to turn down the sound volume.

Press STANDBY/ON

The clock flashes on the display window.

to turn off the unit, if it is turned on.

CAUTION -

INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS

DEFEATED. AVOID EXPOSURE TO BEAM.

VORSICHT !

UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL

GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG

ÜBERBRÜCKT IST. NICHT DEM STRAHL AUSSETZEN!

Press and hold PROGRAM/CLOCK SET for more than 2 seconds.

The hour digits start flashing.

ANTENNAS

The AM antenna is built in, so adjusting the position of the unit may help AM reception.The FM telescopic

antenna on the back of the unit can be extended and rotated for better FM reception.

VARNING -

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH

SPÄRR ÄR URKOPPLAD STRÅLEN ÄR FARLIG.

PAUSE 8 – Press to interrupt tape play or record mode. Press a second time to resume tape play or tape

record mode.

STOP/EJECT § – Press to stop the current tape activity, or to open the cassette compartment door

when no buttons are active.

ADVARSEL -

USYNLIG LASERSTRÅLING VED ÅBNING NÅR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ

UDSÆTTELSE FOR STRÅLING.

Press 4 or ¢ to adjust the hour, then press PROGRAM/CLOCK SET.

The minute digits start flashing.

FF 1 – In stop mode, press to advance the tape toward the end. (When the tape reaches the end, press

STOP/EJECT § to release the depressed button.)

CAUTION

•

Do not block the ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be

able to get out.)

Do not place any naked flame sources, such as lighted candles, on the apparatus.

When discarding batteries, environmental problems must be considered and local rules or laws governing

the disposal of these batteries must be followed strictly.

Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with

liquids, such as vases, shall be placed on the apparatus.

REW ¡ – In stop mode, press to rewind the tape toward the beginning. (When the tape reaches the end,

press STOP/EJECT § to release the depressed button.)

PLAY 2 – Press to play cassettes.

REC ÷ – Press to record from the radio or CD player.

•

Press 4 or ¢ to adjust the minutes, then press PROGRAM/CLOCK SET.

PLAYING A CASSETTE TAPE

1. Press TAPE to enter the tape mode.

2. Press STOP/EJECT § to open the cassette compartment door.

3. Load a cassete. Use only a type-I normal tape.

4. Close the door securely.

5. Press PLAY 2 to begin playing the tape. The cassette tape plays until it reaches the end of the side,

then it automatically stops.

Notes:

•

If there is a power failure, the clock loses the setting and is reset to “0:00.”The clock indication will keep

flashing until you set the clock again.

You can also set the clock when the unit is in STANDBY mode. In this case, follow the procedures from

step 2.

•

To show the clock when the unit is on.

Press DISPLAY.

Each time you press the button, the display changes the clock indication and the normal indication alternately.

(Operating the unit while clock indication is displayed changes the display to the normal indication.)

Fast-winding a tape

Press REW ¡ or FF 1.

When the tape reaches the end, press STOP/EJECT § to release REW ¡ or FF 1.

Download from Www.Somanuals.com. All Manuals Search And Download.

Displaying the disc information (MP3 disc only)

In stop mode:

When you press 4 or ¢ to select a track, the group (album) number and group name\file name scroll

through the display window, and then the current group (album) number and track number are displayed

again.

During playback:

When you press and hold DISPLAY for more than 1 second, the title, artist name and album name* scroll

through the display window once, and then the track number being played and elapsed playing time are

displayed again.

RECORDING ON CASSETTE TAPES

You can record from the radio or the CD player.

HANDLING CASSETTE TAPES

STANDBY/ON

CD door

) PUSH

•

If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels

and rotating.

If the tape is loose, it may get stretched, cut, or caught in the cassette.

4 (skip/search

•

It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs

without the consent of the owner of copyright in the sound or video recording, broadcast or

cable program and in any literary, dramatic, musical, or artistic work embodied therein.

The recording level is automatically set correctly, so it is not affected by the other sound settings.Thus,

during recording you can adjust the sound you are actually listening to without affecting the recording

level.

backward)

BY/ON

STA

PROGRAM/

CLOCK SET

PRES

PRESET

HBS

PRESET

PUSH

GROUP –/+

¢ (skip/search

forward)

•

Be careful not to touch the tape surface.

RANDOM

STOP 7

CD/RANDOM

If recordings you have made have excessive noise or static, the unit may be too close to a TV. Increase

the distance between the TV and the unit.

REMOTE

SENSOR

If the track has no text information, “NO INFO” appears instead.

DISPLAY

AND

PLAY/PAUSE 6

Avoid storing tapes in any of the following places:

- In dusty places

REPEAT

•

You can only use type I tape for recording.

DO NOT turn off the unit while playing back or recording a tape. The cassette deck or tapes may be

damaged.

The REPEAT button repeats one track (REPEAT 1) or all tracks (REPEAT ALL). To scroll through the

choices, continuously press and release REPEAT, and check the display to see which choice you have

selected. The following chart illustrates how REPEAT works in various modes.

- In direct sunlight or heat

- In moist areas

- On a TV or speaker

•

DO NOT use type II and type IV tapes since the unit is not compatible with such tapes.

The use of C-120 or longer tape is not recommended, since characteristic deterioration may occur and

this tape easily jams in the pinch rollers and the capstans.

STANDBY/ON

CD/

RANDOM

TUNER/

BAND

TAPE

NORMAL

REPEAT ALL

REPEAT 1

(For audio CD)

- Near a magnet

CD/RANDOM

DISPLAY

HBS/

PRESET EQ

NORMAL

REPEAT ALL

REPEAT GROUP

REPEAT 1

Number buttons

(For MP3 disc)

CLEANING THE TAPE HEADS

OVER

To protect your recordings

Cassettes have two small tabs on the back to protect against unexpected erasure or re-recording.

To protect your recording, remove these tabs.

FM MODE

/BEAT CUT

PROGRAM/

CLOCK SET

GROUP

–

INTRO

Clean the heads after every 10 hours of use with a wet-type head cleaning tape (available at electronic and

audio shops).

GROUP +/-

INTRO

PRESET

DOWN

REPEAT

MUTING

PROGRAM/CLOCKSET

REPEAT

RANDOM

To re-record on a protected tape, cover the holes with adhesive tape.

In CD mode, press CD/RANDOM so that “RANDOM” appears in the display and random playback starts.

To quit random play, press CD/RANDOM again.

Head

Pinch roller

VOLUME

Capstan

Erasure head

PROGRAMMING

RM-SRCEX30J REMOTE CONTROL

Press CD/RANDOM to enter CD mode, if the unit is in TUNER or TAPE mode.

You can press CD/RANDOM on the remote control unit to enter CD mode.

Press PROGRAM/CLOCK SET in stop mode.

To demagnetize the head

Turn off the unit, and use a head demagnetizer (available at electronic and audio shops).

Adhesive tape

The PROGRAM indicator appears in the display window.

LOADING A CD

RECORDING FROM THE RADIO

1. Insert a cassette tape into the cassette deck and close the door.

2. Press TUNER/BAND and select a radio station.

3. Press REC ÷ to begin recording. REC ÷ and PLAY 2 are locked down.

4. Press STOP/EJECT § to stop recording.

PROGRAM

TROUBLESHOOTING TIPS

1. Press CD/RANDOM; “READING” appears, then “NO DISC” appears in the display if no CD is loaded.

2. Press ) PUSH to open the CD door.

3. Place a CD into the tray with the label facing up.

4. Close the CD door. Then the total number of tracks and total playing time appear.

5. To remove the CD, press ) PUSH, grasp the CD by its edges, and carefully pull it out.

6. When loading an MP3 disc, the MP3 indicator lights, and the total number of groups (albums) and total

number of tracks appear in the display window.

FLAT

Problem

Solution

Press 4 or ¢ to select a desired track to be programmed.

You can use the number buttons on the remote control unit to select a desired track.

• Make sure the power cord is securely plugged into the AC power

outlet (or that the batteries are fresh).

• Unplug the unit for a moment, and then plug it back in again.

• Check the outlet by plugging in another device.

System does not turn on.

Using the beat-cut function

PROGRAM

When recording an AM broadcast, beats may occur. If this happens while recording an AM broadcast,

press FM MODE/BEAT CUT on the remote control unit to select the better beat-cut setting, “CUT-1” or

“CUT-2”.

Track to be programmed

FLAT

• Adjust the volume setting.

• Make sure you have selected the correct function: CD, TAPE, or

TUNER and the headphones are disconnected.

No sound

MP3

Press PROGRAM/CLOCK SET.

Repeat steps 3 and 4 to program other tracks.

Press PLAY/PAUSE 3/8.

Total number of groups

Total number of tracks

• Adjust the FM telescopic antenna for better FM reception.

• Rotate the unit to achieve better AM reception.

• Try turning off electrical appliances near the unit, such as TV, hair

dryers, vacuum cleaners, or fluorrescent lights.

TIP

FLAT

Poor radio reception

To temporarily pause the recording, press PAUSE 8 on the cassette deck.Press PAUSE 8 again to resume

recording.

The tracks are played in the order you have programmed.

Stopping programmed playback

Press STOP 7.

Checking the program contents

PLAYING A CD

Press PLAY/PAUSE 6 to play all the tracks in order starting with track 1.

The current track number and elapsed playing time appear in the display.

SYNCHRONIZED RECORDING FROM A CD

1. Insert a cassette tape into the cassette deck and close the door.

2. Press CD/RANDOM.

3. Place a CD you want to record into CD compartment.

4. Select the track you want to record by pressing 4 or ¢.

5. Press REC ÷ to start synchronized recording.

• Make sure the tray contains a CD.

• Make sure the CD’s label is facing up.

• Make sure that pause mode is not activated.

• Make sure the CD function is selected.

CD does not play.

CD sound skips.

Before starting programmed playback, press PROGRAM/CLOCK SET when “PROGRAM” is displayed.

Each time you press the button, the programmed tracks are shown in the display window.

Notes for MP3 files

• Clean the CD (as explained in “CARE AND MAINTENANCE”).

• Check the CD for warping, scratches, or other damage.

• Check for vibration or shock that may affect the unit; move system if

necessary.

•

When an MP3 disc is loaded, after the current track number and elapsed playing time are displayed for

5 seconds, the ID3 TAG information (title, artist name and album name) scrolls through the display

window once, if the MP3 disc has ID3TAG information.For displaying the disc information, see “Displaying

the disc information”.

Adding tracks in the program

Press PROGRAM/CLOCK SET repeatedly until “00” appears as a track number.

Press 4 or ¢ (or the number buttons on the remote control unit) to select a new track number, then

press PROGRAM/CLOCK SET.

•

When the tape reaches the end, the CD playback enters in pause.

• Inspect the recording head and clean it if necessary.

• Demagnetize recording head (as explained in “CARE AND

MAINTENANCE”).

Distorted or noisy

recordings

To continue recording:

To continue the CD playback:

To stop the CD playback:

turn over the tape and press REC ÷.

press PLAY/PAUSE 3/8.

press STOP 7.

•

When an MP3 disc is loaded, it may take more than 30 seconds to be read, depending on the amount

of information compiled in the disc.

Editing the program

Press PROGRAM/CLOCK SET repeatedly until the program number you want to edit appears.

Press 4 or ¢ (or the number buttons on the remote control unit) to select a new track number, then

press PROGRAM/CLOCK SET.

•

When the CD playback stops, the cassette tape continues running.

Notes

To stop the cassette tape, press STOP/EJECT §.

•

Press PLAY/PAUSE 6 to temporarily stop the CD. The track number and elapsed playing time flash

in the display. Press PLAY/PAUSE 6 again to resume playing the CD.

Adjust VOLUME to a comfortable level.

Erasing the entire program in the memory

TIP

SPECIFICATIONS

•

Press PROGRAM/CLOCK SET so that the “PROGRAM” appears, and press STOP 7 while the

Using the PAUSE 8 button on the cassette deck instead of the STOP/EJECT § button to momentarily

interrupt recording gives you a much clearer sound recording.

Press STOP 7 to stop playing the CD. Wait a few seconds for the CD to stop turning, then press

) PUSH to open the CD door and remove the CD.

“NO DISC” may appear when the disc is loaded upside down. Reload the disc correctly.

“PROGRAM” is displayed.

CD player

The program is also cleared when you open the CD door, turn off the unit or change to other audio

•

sources.

Note

ERASING

CD capacity

: 1 CD

Skipping

Dynamic range

Signal-to-noise ratio

: 60 dB

: 75 dB

When recording on a pre-recorded tape, the previous recording is erased and only the new recording is

heard next time the tape is played back.

•

To skip back to the previous track

You cannot program more than 40 tracks.

“– – FULL – –” is displayed.

During playback, press 4 once to return to the beginning of the current track, press twice to skip back

to the beginning of the previous track.

Erasing a recording on a tape without making a new recording

1. Press TAPE to enter the tape mode.

2 . Press REC ÷ to start recording.

Tuner

For MP3 disc:

Frequency ranges

: FM 87.5 - 108.0 MHz

: AM 530 - 1 710 kHz

•

To skip to the next track

1 Press PROGRAM/CLOCK SET in stop mode.

The PROGRAM indicator appears in the display window.

2 Press GROUP + or GROUP – to select a desired group (album).

The first track number in the selected group (album) is shown.

3 Press 4 or ¢ to select a desired track in the group (album).

You can use the number buttons on the remote control unit to select a desired track.

4 Press PROGRAM/CLOCK SET.

During playback, press ¢ to skip to the beginning of the next track.

Antenna

: Telescopic antenna for FM

Ferrite core antenna for AM

Selecting a desired track directly

Use the number buttons on the remote control unit.

In case of an audio CD:

Example:

To select track 8, press 8.

To select track 21, press OVER, 2, then 1.

Playback starts from the specified track.

In case of an MP3 disc:

USING THE CD

Cassette deck section

THINGS TO KNOW BEFORE PLAYING CDs

Playable CDs:

Frequency response

Wow and flutter

: 60 Hz - 10 000 Hz

: 0.15% (WRMS)

5 Repeat steps 2 to 4 to program other tracks.

6 Press PLAY/PAUSE 3/8.

Only CDs bearing these marks can be used with this system.

General

The tracks are played in the order you have programmed.

Speaker

: 9 cm cone × 2 (4 Ω)

Example:

To select track 8, press 8.

To select track 21, press OVER, 0, 2, then 1.

To select track 115, press OVER, 1, 1, then 5.

Power output

Output terminals

Power supply

: 4 W (2 W + 2 W) at 4 Ω (10% THD) (IEC268-3)

: PHONES × 1 (∅ 3.5 mm, stereo)

: AC 230 V Ó, 50 Hz

Recordable

ReWritable

INTRO PLAYBACK

This unit has been designed only to play back the following CDs.

Every track or every programmed track of a CD (excluding the CD of MP3 format) can be played for the

beginning ten seconds.

•

Digital audio CD

Recordable digital audio CD (CD-R)

Rewritable digital audio CD (CD-RW)

DC 9 V (“R20 (SUM-1)/D (13D)” × 6)

: 18 W (at operation), 3 W (on standby)

: 420 mm (W) × 178 mm (H) × 249 mm (D)

: Approx. 3.4 kg (without batteries)

: AC power cord × 1

Search – locating a desired position on the disc (audio CD only)

Press and hold 4 or ¢ during playback.

Monitor the sound and release the button when the desired position is located.

Power consumption

Dimensions

Mass

Press INTRO on the remote control unit. The INTRO indicator appears in the display window and intro

playback starts.

When playing a CD-R or CD-RW

You can play back finalized CD-R or CD-RW recorded in music CD format or in MP3 format. (If a CD-

RW has been recorded in a different format, erase all the data on the CD-RW completely before recording

on it.)

Accessories provided

Selecting a desired group (album) and track (MP3 disc only)

1 In stop mode, press GROUP + or GROUP – repeatedly until the desired group (album) number is

displayed.

2 Press 4 or ¢ to select a desired track from the current group (album).

3 Press PLAY/PAUSE 3/8 to start playback.

Remote control unit × 1

Batteries for the remote control unit R03 (UM-4)/AAA (24F) × 2

CARE AND MAINTENANCE

•

You can play back CD-R or CD-RW like an audio CD.

Some CD-R or CD-RW may not be played back on this unit because of their disc characteristics,

damage or stain on them, or if the player lens is dirty.

CLEANING THE EXTERIOR

Design and specifications are subject to change without notice.

•

The reflection factor of CD-RW is lower than that of other CDs, possibly causing CD-RW to take longer

time to read.

• Disconnect the system from AC power before cleaning the exterior of the unit with a soft dry cloth.

Note

During playback, if you press GROUP + or GROUP –, playback skips to the first track of the next or

previous group (album), and the track number is shown in the display window.

HANDLING DISCS

Notes for MP3 files

•

The unit can only recognize files with “MP3” or “mp3” as the extensions, which can be in any

combination of upper and lower cases. The file name needs to be up to 20 characters.

This unit recognizes files and folders on a disc in the following conditions:

– up to 999 MP3 files,

– up to 99 folders (including the root folder),

– up to 8th layers (including the root folder).

Note that the number of the folders or layers mentioned above may increase and can be played back

depending on the contents recorded on the disc.

It is recommended that you record your material at a 44.1-kHz sampling rate, using the 128-kbps data

transfer rate.

Some MP3 files or discs may not be played back because of their characteristics or recording

conditions.

MP3 discs require a longer readout time than normal discs because of the complexity of the folder/file

configuration.

Checking the remaining time (audio CD only)

Press and hold DISPLAY (on either the main unit or the remote control unit) for more than 1 second during

playback.

•

Remove the disc from its case by holding it at the edge while pressing the center

hole lightly.

Do not touch the shiny surface of the disc, or bend the disc.

Put the disc back in its case after use to prevent warping.

•

Each time you press and hold the button, the display changes in the following order:

Track number being played and elapsed playing time.

•

Be careful not to scratch the surface of the disc when placing it back in its case.

Avoid exposure to direct sunlight, temperature extremes, and moisture.

•

Track number being played and remaining time of the track (“TRACK” and “REMAIN” appear.)

Track number being played and remaining time of the disc (“TOTAL” and “REMAIN” appear.)

To clean the disc

•

Wipe the disc with a soft cloth in a straight line from center to edge.

DO NOT use any solvent – such as conventional record cleaner, spray, thinner, or

benzine – to clean the disc.

•

MP3i and MP3 Pro are not available.

The title, artist name and album name can be displayed as the ID3 TAG (ID3v1/1.1) information.

Caution for DualDisc playback

The Non-DVD side of a “DualDisc”does not comply with the“Compact Disc Digital Audio”standard.Therefore,

the use of Non-DVD side of a DualDisc on this product may not be recommended.

Download from Www.Somanuals.com. All Manuals Search And Download.

ADJUSTING THE SOUND

Turn the VOLUME knob (or pressVOLUME + / – button on the remote control unit) to increase or decrease

the volume to desired level. The volume level can be adjusted in 31 steps from “MIN” to “MAX”.

FIRST THINGS

NAMES OF PARTS AND CONTROLS

ENGLISH

This portable system operates on battery or AC power.

Top and front sides:

Main unit

•

Turning off the sound temporarily

During playback, press MUTING on the remote control unit to turn the sound off.The MUTING indicator

appears in the display window. Press it again to restore the sound.

CD PORTABLE SYSTEM

FM telescopic antenna

PHONES jack

RC-EX36S

2 3

4 5

6 7 8

Reinforcing the bass sound

Press and hold HBS/PRESET EQ so that the HBS indicator appears in the display window. You can

enjoy powerful bass sound with the Hyper-Bass Sound effect.

BY/ON

STA

OGRAM/

OCK SET

PRESET

PUSH

Supplied power cord

Selecting the sound mode

You can select one of the 5 preset sound modes.

Press HBS/PRESET EQ repeatedly until the indicator for the sound mode you want appears in the

display window.

AC outlet

APE

RANDOM

Battery compartment

Y/P

PLA

TUNER

REMOTE

SENSOR

DISPLAY

CLASSIC: Enriched sound with fine treble and ample bass.

ROCK : Powerful sound emphasizing treble and bass.

POP : More presence in the vocals and midrange.

JAZZ : Accented lower frequencies for jazz-type music.

FLAT : Equalizer effect is canceled.

INSERTING BATTERIES

Open the battery compartment cover.

Pull the battery compartment cover toward you while pressing the sections marked by the arrows.

Insert six R20 (SUM-1)/D (13D)-size batteries. (not supplied)

Be sure to insert the batteries with the (+) and (–) terminals positioned correctly.

USING THE RADIO

10 11 12 13 14 15

TUNING IN RADIO STATIONS

PRESET UP button

TAPE button

VOLUME knob

STANDBY/ON

GROUP – button

GROUP + button

Press TUNER/BAND to enter the tuner mode.

button

Press TUNER/BAND to select the band, FM or AM.

Press and hold 4 or ¢ for more than 1 second.

The unit starts searching and stops when a station of sufficient signal strength is tuned in.

If you press 4 or ¢ briefly and repeatedly, the frequency changes step by step.

CD/RANDOM button

TUNER/BAND button

INSTRUCTIONS

10 REMOTE SENSOR

11 Display window

12 Cassette deck

13 DISPLAY button

14 4 button

Tape operation buttons

PAUSE 8 button

R20 (SUM-1)/D (13D)-size batteries

Changing the FM reception mode

When an FM stereo broadcast is hard to receive or noisy, press FM MODE/BEAT CUT on the remote

control unit so that the MONO indicator appears in the display window.

To restore the stereo effect, press FM MODE/BEAT CUT again so that the MONO indicator goes off.

The FM MODE will be changed to STEREO also when changing the station.

STOP/EJECT § button

FF 1 button

Thank you for purchasing this JVC product.

Please read these instructions carefully before starting operation to be

sure to obtain optimum performance and a longer service life from the

unit.

Replace the battery compartment cover.

REW ¡ button

PLAY 2 button

¢ button

Inserting Batteries into the Remote Control Unit:

PLAY/PAUSE 6 button

STOP 7 button

REC ÷ button

LVT1385-008A [E/EN]

Match the polarity (+ and –) of the batteries. R03 (UM-4)/AAA (24F)×2 (supplied)

CD door

0205NSMBICORI

PRESETTING STATIONS

You can preset 20 FM and 10 AM stations.

15 HBS/PRESET EQ button

PRESET DOWN button

PROGRAM/CLOCK SET button

Press TUNER/BAND to select the band, FM or AM.

Press 4 or ¢ to tune in the station you want to preset.

Press PROGRAM/CLOCK SET.

SAFETY PRECAUTIONS

Names of buttons:

Remote control unit

The PROGRAM indicator and the preset number start blinking in the display window.

Caution ––

STANDBY/ON switch!

Disconnect the mains plug to shut the power off completely. The

position does not disconnect the mains line. The power can be remote controlled.

STANDBY/ON switch in any

PROGRAM

Note: The battery power will be switched off when you plug the power cord into the Ó AC

STANDBY/ON

CD/

TUNER/

BAND

RANDOM

TAPE

IN jack on the unit.

MHz

CAUTION

FLAT

DISPLAY

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

HBS/

PRESET EQ

OVER

CAUTION:

Press PRESET UP or PRESET DOWN to select the preset number while the PROGRAM indicator is

blinking.

You can use the number buttons on the remote control unit to select the preset number directly.

Example: To select preset number 5, press 5. To select preset number 15, press OVER, 1, then 5.

To select preset number 20, press OVER, 2, then 0.

FM MODE

/BEAT CUT

To avoid battery leakage or explosion, handle batteries properly.

• If you are not going to use your system for a month or more, remove the batteries from the battery

compartment.

• Dispose of batteries in the proper manner, according to federal, state, and local regulations.

• Do not mix with different battery types or with new and old ones, or do not attempt to charge a

battery not intended to be recharged.

PROGRAM/

CLOCK SET

GROUP

–

INTRO

PRESET

DOWN

REPEAT

MUTING

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

VOLUME

CAUTION: Do not open the top cover. There are no user serviceable parts inside

PROGRAM

the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or

defeated. Avoid direct exposure to beam.

• Discard leaky batteries immediately.Leaking batteries can cause skin burns or other personal injury.

Preset number

MHz

RM-SRCEX30J REMOTE CONTROL

FLAT

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.

SUPPRLYING AC POWER

Press PROGRAM/CLOCK SET while the PROGRAM indicator is blinking.

The tuned station in step 2 is stored in the preset number selected in step 4.

Storing a new station on a used number erases the previously stored one.

When the PROGRAM indicator stops blinking, the tuned station is stored in the preset number without

pressing PROGRAM/CLOCK SET.

If you use the number buttons to select the preset number in step 4, pressing PROGRAM/CLOCK SET

is not necessary in this step.

Repeat steps 2 to 5 to preset other stations, using different preset numbers.

Plug the power cord into the Ó AC IN jack on the back of the unit, and into an AC power outlet.

Note: To switch off the system completely, unplug the power cord.

CAUTION -

INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS

DEFEATED. AVOID EXPOSURE TO BEAM.

STANDBY/ON

DISPLAY button

button

CD/RANDOM button

TUNER/BAND button

TAPE button

Number buttons

GROUP +/– buttons

VOLUME +/– buttons

VORSICHT !

UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL

GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG

ÜBERBRÜCKT IST. NICHT DEM STRAHL AUSSETZEN!

CAUTIONS:

HBS/PRESET EQ button

FM MODE/BEAT CUT button

PRESET UP/DOWN buttons

PROGRAM/CLOCK SET button

INTRO button

1. ONLY USE JVC POWER CORD PROVIDED WITH THIS UNIT TO AVOID MALFUNCTION OR

DAMAGE TO THE UNIT. REMOVE BATTERIES WHEN USING THE POWER CORD.

2. BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN

THE UNIT IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.

VARNING -

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH

SPÄRR ÄR URKOPPLAD STRÅLEN ÄR FARLIG.

ADVARSEL -

USYNLIG LASERSTRÅLING VED ÅBNING NÅR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ

UDSÆTTELSE FOR STRÅLING.

REPEAT button

MUTING button

Tuning in a preset station

USING HEADPHONES

Press TUNER/BAND to select the band, FM or AM.

Press PRESET UP or PRESET DOWN repeatedly until the desired preset number appears.

You can use the number buttons on the remote control unit to select the preset number directly.

Example:

Connect commercially available headphones to the PHONES jack on the rear of the main unit. While the

headphones are connected, the speakers do not produce any sound. Before connecting the headphones,

make sure to turn down the sound volume.

3/8 button

4 button

CAUTION

•

¢ button

Do not block the ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able

to get out.)

Do not place any naked flame sources, such as lighted candles, on the apparatus.

When discarding batteries, environmental problems must be considered and local rules or laws govern-

ing the disposal of these batteries must be followed strictly.

Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with

liquids, such as vases, shall be placed on the apparatus.

7 button

To select preset number 5, press 5.

To select preset number 15, press OVER, 1, then 5.

To select preset number 20, press OVER, 2, then 0.

ANTENNAS

The AM antenna is built in, so adjusting the position of the unit may help AM reception.The FM telescopic

antenna on the back of the unit can be extended and rotated for better FM reception.

•

GENERAL CONTROLS

Note

If you unplug the AC power cord or if a power failure occurs, the preset stations will be erased in a few

days. If this happens, preset the stations again.

•

STANDBY/ON

- Press to turn on/off the unit.

The display window lights up when the unit is turned on. (Note, however, that the display window does not

light even when the unit is turned on if the unit is operated on batteries.)

USING THE TAPE

SETTING THE CLOCK

Before operating the unit any further, first set the clock built in this unit.

The clock uses 24-hour indication.

|Forward direction

Caution: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate

the apparatus as follows:

Press STANDBY/ON

The clock flashes on the display window.

to turn off the unit, if it is turned on.

Front:

No obstructions and open spacing.

Sides/ Top/ Back:

No obstructions should be placed in the areas shown by the dimensions below.

Bottom:

Press and hold PROGRAM/CLOCK SET for more than 2 seconds.

The hour digits start flashing.

Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand

with a height of 10 cm or more.

PAUSE 8 – Press to interrupt tape play or record mode. Press a second time to resume tape play or tape

record mode.

STOP/EJECT § – Press to stop the current tape activity, or to open the cassette compartment door

when no buttons are active.

Press 4 or ¢ to adjust the hour, then press PROGRAM/CLOCK SET.

Front view

Side view

15 cm

The minute digits start flashing.

FF 1 – In stop mode, press to advance the tape toward the end. (When the tape reaches the end, press

STOP/EJECT § to release the depressed button.)

15 cm

REW ¡ – In stop mode, press to rewind the tape toward the beginning. (When the tape reaches the end,

press STOP/EJECT § to release the depressed button.)

10 cm

PLAY 2 – Press to play cassettes.

REC ÷ – Press to record from the radio or CD player.

Press 4 or ¢ to adjust the minutes, then press PROGRAM/CLOCK SET.

PLAYING A CASSETTE TAPE

1. Press TAPE to enter the tape mode.

Notes:

•

If there is a power failure, the clock loses the setting and is reset to “0:00.”The clock indication will keep

2. Press STOP/EJECT § to open the cassette compartment door.

3. Load a cassete. Use only a type-I normal tape.

4. Close the door securely.

5. Press PLAY 2 to begin playing the tape. The cassette tape plays until it reaches the end of the side,

then it automatically stops.

flashing until you set the clock again.

You can also set the clock when the unit is in STANDBY mode. In this case, follow the procedures from

step 2.

•

To show the clock when the unit is on.

Press DISPLAY.

Each time you press the button, the display changes the clock indication and the normal indication alternately.

(Operating the unit while clock indication is displayed changes the display to the normal indication.)

Fast-winding a tape

Press REW ¡ or FF 1.

When the tape reaches the end, press STOP/EJECT § to release REW ¡ or FF 1.

Download from Www.Somanuals.com. All Manuals Search And Download.

Displaying the disc information (MP3 disc only)

In stop mode:

When you press 4 or ¢ to select a track, the group (album) number and group name\file name scroll

through the display window, and then the current group (album) number and track number are displayed

again.

During playback:

When you press and hold DISPLAY for more than 1 second, the title, artist name and album name* scroll

through the display window once, and then the track number being played and elapsed playing time are

displayed again.

RECORDING ON CASSETTE TAPES

You can record from the radio or the CD player.

HANDLING CASSETTE TAPES

STANDBY/ON

CD door

) PUSH

•

If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels

and rotating.

If the tape is loose, it may get stretched, cut, or caught in the cassette.

4 (skip/search

•

It may be unlawful to record or play back copyrighted material without the consent of the copyright

owner.

backward)

BY/ON

STA

PROGRAM/

CLOCK SET

•

The recording level is automatically set correctly, so it is not affected by the other sound settings.Thus,

during recording you can adjust the sound you are actually listening to without affecting the recording

level.

PRES

PRESET

HBS

PRESET

PUSH

GROUP –/+

¢ (skip/search

forward)

•

Be careful not to touch the tape surface.

•

If recordings you have made have excessive noise or static, the unit may be too close to a TV. Increase

the distance between the TV and the unit.

RANDOM

STOP 7

CD/RANDOM

REMOTE

SENSOR

If the track has no text information, “NO INFO” appears instead.

DISPLAY

AND

•

You can only use type I tape for recording.

DO NOT turn off the unit while playing back or recording a tape. The cassette deck or tapes may be

damaged.

PLAY/PAUSE 6

Avoid storing tapes in any of the following places:

- In dusty places

REPEAT

- In direct sunlight or heat

- In moist areas

- On a TV or speaker

The REPEAT button repeats one track (REPEAT 1) or all tracks (REPEAT ALL). To scroll through the

choices, continuously press and release REPEAT, and check the display to see which choice you have

selected. The following chart illustrates how REPEAT works in various modes.

•

DO NOT use type II and type IV tapes since the unit is not compatible with such tapes.

The use of C-120 or longer tape is not recommended, since characteristic deterioration may occur and

this tape easily jams in the pinch rollers and the capstans.

STANDBY/ON

CD/

RANDOM

TUNER/

BAND

TAPE

- Near a magnet

NORMAL

REPEAT ALL

REPEAT 1

CD/RANDOM

(For audio CD)

DISPLAY

To protect your recordings

Cassettes have two small tabs on the back to protect against unexpected erasure or re-recording.

To protect your recording, remove these tabs.

HBS/

PRESET EQ

Number buttons

CLEANING THE TAPE HEADS

OVER

FM MODE

/BEAT CUT

NORMAL

REPEAT ALL

REPEAT GROUP

REPEAT 1

(For MP3 disc)

PROGRAM/

CLOCK SET

GROUP

–

INTRO

Clean the heads after every 10 hours of use with a wet-type head cleaning tape (available at electronic and

audio shops).

GROUP +/-

INTRO

PRESET

DOWN

REPEAT

MUTING

PROGRAM/CLOCKSET

REPEAT

To re-record on a protected tape, cover the holes with adhesive tape.

RANDOM

Head

Pinch roller

VOLUME

In CD mode, press CD/RANDOM so that “RANDOM” appears in the display and random playback starts.

To quit random play, press CD/RANDOM again.

Capstan

Erasure head

RM-SRCEX30J REMOTE CONTROL

PROGRAMMING

Adhesive tape

To demagnetize the head

Turn off the unit, and use a head demagnetizer (available at electronic and audio shops).

Press CD/RANDOM to enter CD mode, if the unit is in TUNER or TAPE mode.

You can press CD/RANDOM on the remote control unit to enter CD mode.

Press PROGRAM/CLOCK SET in stop mode.

RECORDING FROM THE RADIO

1. Insert a cassette tape into the cassette deck and close the door.

2. Press TUNER/BAND and select a radio station.

LOADING A CD

The PROGRAM indicator appears in the display window.

TROUBLESHOOTING TIPS

1. Press CD/RANDOM; “READING” appears, then “NO DISC” appears in the display if no CD is loaded.

2. Press ) PUSH to open the CD door.

3. Place a CD into the tray with the label facing up.

4. Close the CD door. Then the total number of tracks and total playing time appear.

5. To remove the CD, press ) PUSH, grasp the CD by its edges, and carefully pull it out.

6. When loading an MP3 disc, the MP3 indicator lights, and the total number of groups (albums) and total

number of tracks appear in the display window.

PROGRAM

3. Press REC ÷ to begin recording. REC ÷ and PLAY 2 are locked down.

4. Press STOP/EJECT § to stop recording.

Problem

Solution

FLAT

• Make sure the power cord is securely plugged into the AC power

outlet (or that the batteries are fresh).

• Unplug the unit for a moment, and then plug it back in again.

• Check the outlet by plugging in another device.

Using the beat-cut function

Press 4 or ¢ to select a desired track to be programmed.

You can use the number buttons on the remote control unit to select a desired track.

System does not turn on.

When recording an AM broadcast, beats may occur. If this happens while recording an AM broadcast,

press FM MODE/BEAT CUT on the remote control unit to select the better beat-cut setting, “CUT-1” or

“CUT-2”.

PROGRAM

• Adjust the volume setting.

No sound

MP3

• Make sure you have selected the correct function: CD, TAPE, or

TUNER and the headphones are disconnected.

Track to be programmed

FLAT

TIP

Total number of groups

Total number of tracks

• Adjust the FM telescopic antenna for better FM reception.

• Rotate the unit to achieve better AM reception.

• Try turning off electrical appliances near the unit, such as TV, hair

dryers, vacuum cleaners, or fluorrescent lights.

To temporarily pause the recording, press PAUSE 8 on the cassette deck.Press PAUSE 8 again to resume

Press PROGRAM/CLOCK SET.

Repeat steps 3 and 4 to program other tracks.

Press PLAY/PAUSE 3/8.

FLAT

Poor radio reception

recording.

SYNCHRONIZED RECORDING FROM A CD

1. Insert a cassette tape into the cassette deck and close the door.

2. Press CD/RANDOM.

3. Place a CD you want to record into CD compartment.

4. Select the track you want to record by pressing 4 or ¢.

5. Press REC ÷ to start synchronized recording.

The tracks are played in the order you have programmed.

PLAYING A CD

Press PLAY/PAUSE 6 to play all the tracks in order starting with track 1.

The current track number and elapsed playing time appear in the display.

• Make sure the tray contains a CD.

Stopping programmed playback

Press STOP 7.

Checking the program contents

Before starting programmed playback, press PROGRAM/CLOCK SET when “PROGRAM” is displayed.

Each time you press the button, the programmed tracks are shown in the display window.

• Make sure the CD’s label is facing up.

• Make sure that pause mode is not activated.

• Make sure the CD function is selected.

CD does not play.

CD sound skips.

Notes for MP3 files

• Clean the CD (as explained in “CARE AND MAINTENANCE”).

• Check the CD for warping, scratches, or other damage.

• Check for vibration or shock that may affect the unit; move system if

necessary.

•

When an MP3 disc is loaded, after the current track number and elapsed playing time are displayed for

5 seconds, the ID3 TAG information (title, artist name and album name) scrolls through the display

window once, if the MP3 disc has ID3TAG information.For displaying the disc information, see “Displaying

the disc information”.

•

When the tape reaches the end, the CD playback enters in pause.

Adding tracks in the program

To continue recording:

To continue the CD playback:

To stop the CD playback:

turn over the tape and press REC ÷.

press PLAY/PAUSE 3/8.

press STOP 7.

Press PROGRAM/CLOCK SET repeatedly until “00” appears as a track number.

Press 4 or ¢ (or the number buttons on the remote control unit) to select a new track number, then

press PROGRAM/CLOCK SET.

• Inspect the recording head and clean it if necessary.

• Demagnetize recording head (as explained in “CARE AND

MAINTENANCE”).

Distorted or noisy

recordings

•

When an MP3 disc is loaded, it may take more than 30 seconds to be read, depending on the amount

of information compiled in the disc.

•

When the CD playback stops, the cassette tape continues running.

Editing the program

To stop the cassette tape, press STOP/EJECT §.

Notes

Press PROGRAM/CLOCK SET repeatedly until the program number you want to edit appears.

Press 4 or ¢ (or the number buttons on the remote control unit) to select a new track number, then

press PROGRAM/CLOCK SET.

•

Press PLAY/PAUSE 6 to temporarily stop the CD. The track number and elapsed playing time flash

TIP

SPECIFICATIONS

in the display. Press PLAY/PAUSE 6 again to resume playing the CD.

Adjust VOLUME to a comfortable level.

Using the PAUSE 8 button on the cassette deck instead of the STOP/EJECT § button to momentarily

•

Erasing the entire program in the memory

Press PROGRAM/CLOCK SET so that the “PROGRAM” appears, and press STOP 7 while the

“PROGRAM” is displayed.

The program is also cleared when you open the CD door, turn off the unit or change to other audio

sources.

interrupt recording gives you a much clearer sound recording.

Press STOP 7 to stop playing the CD. Wait a few seconds for the CD to stop turning, then press

) PUSH to open the CD door and remove the CD.

“NO DISC” may appear when the disc is loaded upside down. Reload the disc correctly.

CD player

CD capacity

Dynamic range

Signal-to-noise ratio

ERASING

: 1 CD

: 60 dB

: 75 dB

•

When recording on a pre-recorded tape, the previous recording is erased and only the new recording is

Skipping

heard next time the tape is played back.

•

To skip back to the previous track

Note

Erasing a recording on a tape without making a new recording

1. Press TAPE to enter the tape mode.

2 . Press REC ÷ to start recording.

Tuner

Frequency ranges

During playback, press 4 once to return to the beginning of the current track, press twice to skip back

to the beginning of the previous track.

You cannot program more than 40 tracks.

“– – FULL – –” is displayed.

: FM 87.5 - 108.0 MHz

: AM 530 - 1 710 kHz

: Telescopic antenna for FM

Ferrite core antenna for AM

•

To skip to the next track

For MP3 disc:

Antenna

During playback, press ¢ to skip to the beginning of the next track.

1 Press PROGRAM/CLOCK SET in stop mode.

The PROGRAM indicator appears in the display window.

2 Press GROUP + or GROUP – to select a desired group (album).

The first track number in the selected group (album) is shown.

3 Press 4 or ¢ to select a desired track in the group (album).

You can use the number buttons on the remote control unit to select a desired track.

4 Press PROGRAM/CLOCK SET.

5 Repeat steps 2 to 4 to program other tracks.

6 Press PLAY/PAUSE 3/8.

The tracks are played in the order you have programmed.

USING THE CD

Selecting a desired track directly

Use the number buttons on the remote control unit.

In case of an audio CD:

Example:

To select track 8, press 8.

To select track 21, press OVER, 2, then 1.

Playback starts from the specified track.

In case of an MP3 disc:

Cassette deck section

Frequency response

Wow and flutter

THINGS TO KNOW BEFORE PLAYING CDs

Playable CDs:

: 60 Hz - 10 000 Hz

: 0.15% (WRMS)

Only CDs bearing these marks can be used with this system.

General

Speaker

Power output

Output terminals

Power supply

: 9 cm cone × 2 (4 Ω)

: 4 W (2 W + 2 W) at 4 Ω (10% THD) (IEC268-3)

: PHONES × 1 (∅ 3.5 mm, stereo)

: AC 230 V Ó, 50 Hz

DC 9 V (“R20 (SUM-1)/D (13D)” × 6)

: 18 W (at operation), 3 W (on standby)

: 420 mm (W) × 178 mm (H) × 249 mm (D)

: Approx. 3.4 kg (without batteries)

: AC power cord × 1

Recordable

ReWritable

Example:

To select track 8, press 8.

To select track 21, press OVER, 0, 2, then 1.

To select track 115, press OVER, 1, 1, then 5.

This unit has been designed only to play back the following CDs.

•

Digital audio CD

Recordable digital audio CD (CD-R)

Rewritable digital audio CD (CD-RW)

INTRO PLAYBACK

Power consumption

Dimensions

Mass

Every track or every programmed track of a CD (excluding the CD of MP3 format) can be played for the

beginning ten seconds.

Search – locating a desired position on the disc (audio CD only)

Press and hold 4 or ¢ during playback.

Monitor the sound and release the button when the desired position is located.

When playing a CD-R or CD-RW

Accessories provided

You can play back finalized CD-R or CD-RW recorded in music CD format or in MP3 format. (If a CD-

RW has been recorded in a different format, erase all the data on the CD-RW completely before recording

on it.)

Press INTRO on the remote control unit. The INTRO indicator appears in the display window and intro

playback starts.

Remote control unit × 1

Selecting a desired group (album) and track (MP3 disc only)

1 In stop mode, press GROUP + or GROUP – repeatedly until the desired group (album) number is

displayed.

2 Press 4 or ¢ to select a desired track from the current group (album).

3 Press PLAY/PAUSE 3/8 to start playback.

Batteries for the remote control unit R03 (UM-4)/AAA (24F) × 2

•

You can play back CD-R or CD-RW like an audio CD.

Some CD-R or CD-RW may not be played back on this unit because of their disc characteristics,

damage or stain on them, or if the player lens is dirty.

The reflection factor of CD-RW is lower than that of other CDs, possibly causing CD-RW to take longer

time to read.

Design and specifications are subject to change without notice.

CARE AND MAINTENANCE

•

Note

CLEANING THE EXTERIOR

During playback, if you press GROUP + or GROUP –, playback skips to the first track of the next or

previous group (album), and the track number is shown in the display window.

Notes for MP3 files

•

The unit can only recognize files with “MP3” or “mp3” as the extensions, which can be in any

combination of upper and lower cases. The file name needs to be up to 20 characters.

This unit recognizes files and folders on a disc in the following conditions:

– up to 999 MP3 files,

• Disconnect the system from AC power before cleaning the exterior of the unit with a soft dry cloth.

Checking the remaining time (audio CD only)

Press and hold DISPLAY (on either the main unit or the remote control unit) for more than 1 second during

playback.

•

HANDLING DISCS

– up to 99 folders (including the root folder),

– up to 8th layers (including the root folder).

Each time you press and hold the button, the display changes in the following order:

•

Remove the disc from its case by holding it at the edge while pressing the center

hole lightly.

Do not touch the shiny surface of the disc, or bend the disc.

Put the disc back in its case after use to prevent warping.

Note that the number of the folders or layers mentioned above may increase and can be played back

Track number being played and elapsed playing time.

•

depending on the contents recorded on the disc.

•

It is recommended that you record your material at a 44.1-kHz sampling rate, using the 128-kbps data

transfer rate.

Some MP3 files or discs may not be played back because of their characteristics or recording

conditions.

MP3 discs require a longer readout time than normal discs because of the complexity of the folder/file

configuration.

Track number being played and remaining time of the track (“TRACK” and “REMAIN” appear.)

Track number being played and remaining time of the disc (“TOTAL” and “REMAIN” appear.)

•

Be careful not to scratch the surface of the disc when placing it back in its case.

Avoid exposure to direct sunlight, temperature extremes, and moisture.

•

MP3i and MP3 Pro are not available.

The title, artist name and album name can be displayed as the ID3 TAG (ID3v1/1.1) information.

To clean the disc

•

Wipe the disc with a soft cloth in a straight line from center to edge.

DO NOT use any solvent – such as conventional record cleaner, spray, thinner, or

benzine – to clean the disc.

Caution for DualDisc playback

The Non-DVD side of a “DualDisc”does not comply with the“Compact Disc Digital Audio”standard.Therefore,

the use of Non-DVD side of a DualDisc on this product may not be recommended.

Download from Www.Somanuals.com. All Manuals Search And Download.

Init Indoor Furnishings NT MS158 User Manual
Insignia Blender NS BLSS02 User Manual
Intel Whiteboard Accessories LGA 771 User Manual
JMR electronic TV Mount G5312 User Manual
JVC CD Player GET0253 003A User Manual
JVC Projection Television 1004TNH II IM User Manual
JVC Stereo Receiver RX 5030VBK User Manual
Kaidan Camera Accessories KiWiTM 2900 User Manual
Kambrook Vacuum Cleaner KBV30 User Manual
Kenwood Blender BL760 User Manual