Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
5
Introduction
Features
6
7
Minimum Requirements
Get to Know the Broadband Router
Back Panel
Front Panel
Setup Diagram
7
8
9
9
Getting Started
Chapter 1: Quick Setup (via web UI)
About Quick Setup
Step 1: Time Zone
Step 2: Broadband Type
1.1 Cable Modem
1.2 Fixed IP xDSL
1.3 PPPoE
18
18
19
20
21
22
24
1.4 PPTP
Chapter 2: General Setup
General Settings
2.1 System
26
27
28
29
30
31
33
33
33
33
33
36
37
38
39
41
43
44
46
48
51
52
2.1.1 Time Zone
2.1.2 Password Settings
2.1.3 Remote Management
2.2 WAN
2.2.1 Dynamic IP Address
2.2.2 Static IP Address
2.2.3 PPPoE
2.2.4 PPTP
2.2.5 L2TP
2.2.6 Telstra Big Pond
2.2.7 WAN Policy
2.2.8 DNS
2.2.9 DDNS
2.3 LAN
2.4 NAT
2.4.1 Port Forwarding
2.4.2 Virtual Server
2.4.3 Special Applications
2.4.4 UPnP
2.4.5 Protocol and Port Binding
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.6 ALG Settings
2.4.7 Static Routing
2.5 Firewall
54
55
56
58
62
63
65
2.5.1 Access Control
2.5.2 URL Blocking
2.5.3 DoS (Denial of Service)
2.5.4 DMZ
Chapter 3: Status
Status
67
68
69
70
71
72
73
74
3.1 Status and Information
3.2 Internet Connection
3.3 Device Status
3.4 System Log
3.5 Security Log
3.6 Active DHCP Client
3.7 Statistics
Chapter 4: Tools
Tools
75
76
77
78
4.1 Configuration Tools
4.2 Firmware Upgrade
4.3 Reset
Appendix A
Glossary
79
80
4
Download from Www.Somanuals.com. All Manuals Search And Download.
The complete H2BR4 package consists of:
•
•
One H2BR4 Dual WAN 4-Port Firewall Router
One Quick Installation Guide
•
One CD with User’s Manual
•
•
One Power Adapter
Accessories
Check to make sure that the unit was not damaged during shipping and that no items are missing. If you encounter a
problem, please contact your dealer.
Please read this manual thoroughly, and follow the installation and operation procedures detailed in this user’s manual.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The high performance Hawking H2BR4 Dual WAN Firewall Router with built-in 4-port 10/100M Ethernet Switch
provides an easy-to-use, cost-effective means of sharing two broadband Internet connections with your LAN (Local Area
Network). With the H2BR4’s two WAN ports, users experience significantly faster data rates as a result of increased and
more efficient use of bandwidth. The dual WAN ports also provide: an easy way to utilize two different types of
broadband Internet connections on the same network (i.e., DSL, Cable, T1, etc.), a method for selectively managing traffic
between Internet connections (i.e., by port or IP address), and a back-up method that activates the second WAN if the first
WAN should get disconnected.
The H2BR4 features high-level security and is equipped with true, hardware-based firewall protection. The firewall
utilizes Stateful Packet Inspection (SPI) technology, Network Address Translation, and prevents against Denial of Service
(DoS) attacks from outside intruders. In addition, the VPN (Virtual Private Network) pass-through feature allows for fast,
reliable, and secure access to your corporate network via a public Internet network.
The H2BR4 includes a full set of powerful features. It utilizes Network Address Translation (NAT) to expand your
existing network without affecting existing IP based account schemes. The router supports DSL, Cable, and other
broadband modem connections that connect to an RJ-45 Ethernet port. The H2BR4 also features Virtual Server and DMZ
functions, which allow the user to protect clients on the network behind the router while permitting specified traffic to be
opened up outside the network. The router has a built-in DHCP server, which eliminates the need to configure each IP
address manually. The user-friendly web management interface provides the user with an easy way to configure the
router from anywhere in the world using a web browser. The H2BR4 can easily be firmware upgraded and is compatible
with all standard Internet applications. It provides a complete solution for small/medium business and small office/home
office users.
Features
•
•
•
•
•
•
•
•
Superb throughput of up to 50Mbps
Allows multiple users to share a single Internet line or two Internet lines
Supports up to 253 users
Internet Access via Cable or xDSL modem
Can Access Private LAN Servers from the Public Network
Equipped with two WAN ports (10/100M) and four LAN ports (10/100M)
Supports DHCP (Server/Client) for easy setup
Supports advanced features such as:
o
o
o
o
o
o
o
o
Special Applications (i.e., Port Triggers, etc.)
DMZ
Virtual Servers
Network Access Control
Firewall
Bridge mode
DDNS (DynDNS/TZO)
Content Filtering
•
•
•
Allows you to monitor the router’s status via: DHCP Client Log, Security Log and Device/Connection Status
Easy-to-use Web-based user interface for configuration and management purposes
Remote management allows configuration and upgrades from a remote site (over the Internet)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Minimum Requirements
•
•
•
One External xDSL (ADSL) or Cable modem with an Ethernet port (RJ-45)
Network Interface Card (NIC) for each Personal Computer (PC)
PCs with a Web-Browser (Internet Explorer 4.0 or higher, or Netscape Navigator 4.7 or higher)
Note
The WAN “idle timeout” auto-disconnect function may not work due to abnormal activities of some network application
software, computer viruses or hacker attacks from the Internet. For example, some types of software send network packets
to the Internet in the background, even when you are not using the Internet. This function also may not work with some
ISPs. Please make sure this function works properly when you use this function for the first time, especially if your ISP
charges you according to time used. Due to such issues, we cannot guarantee that the WAN “idle timeout” auto-
disconnect function will work in all situations. In order to prevent an extra fee from being charged by the ISP, if your ISP
uses such a fee structure, please turn off the router when you are finished using the Internet.
Get to Know the Broadband Router
Back Panel
The diagram below (Figure 1.0) shows the router’s back panel. The router’s back panel is divided into three sections,
LAN, WAN and Reset:
LAN
WAN
Figure 0.0
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1) Local Area Network (LAN)
The router’s four LAN ports are what you will use to connect your PCs, print servers, switches, etc.
2) Wide Area Network (WAN)
The WAN ports are the segments that connect to your xDSL or Cable modems and are linked to the Internet.
3) Reset
The Reset button allows you to do one of two things:
i.
If problems occur with your router, press the router’s reset button with a narrow pen tip (for less than four
seconds) and the router will re-boot itself, keeping your original configurations.
ii.
If problems persist or become serious, or if you forget your password, press the reset button for longer
than four seconds and the router will reset itself to the factory default settings. Warning: Your original
configurations will be replaced with the factory default settings.
Front Panel
The LED lights located on the router’s front/top panel provide you with information on the device’s status at any given
time. Below is a detailed description of the LEDs.
Figure 0.1
LED
Light Status
ON
Description
PWR
Router’s power supply is on
WAN 10/100M (Port 1-2)
WAN LNK/ACT (Port 1-2)
ON
Off
ON
100Mbps connection
10Mbps connection
WAN is connected
Off
No WAN connection
Flashing
WAN port has Activity (ACT); data being sent
LAN 10/100M (Port 1-4)
LAN LNK/ACT (Port 1-4)
ON
Off
ON
100Mbps connection
10Mbps connection
LAN is connected
Off
No LAN connection
Flashing
LAN port has Activity (ACT); data being sent
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Diagram
Figure 1.2 below shows a typical setup for a Local Area Network (LAN).
Figure 0.2
Getting started
The following are step-by-step instructions on how to start using the router and get connected to the Internet.
1)
2)
Set up your network as shown in the setup diagram above (Figure 1.2).
You then need to set your LAN PC clients so that they can obtain an IP address automatically. All LAN clients
require an IP address. Just like a street address, it allows LAN clients to find one another. (If you have already
configured your PC to obtain an IP address automatically then proceed to step 3, page 11.)
Configure your PC to obtain an IP address automatically
By default, the router’s DHCP is on (enabled). This means that you can obtain an IP address automatically once
you’ve configured your PC to obtain an IP address automatically. This section will show you how to configure
your PC so that it can obtain an IP address automatically for either Windows 95/98/Me, 2000 or NT operating
9
Download from Www.Somanuals.com. All Manuals Search And Download.
systems. For other operating systems (Macintosh, Sun, etc.), follow the manufacturer’s instructions. The
following is a step-by-step illustration on how to configure your PC to obtain an IP address automatically for: 2a)
Windows 95/98/Me, 2b) Windows 2000 and 2c) Windows NT.
2a) Windows 95/98/Me
i: Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.
ii: Double-click Network icon. The Network window will appear.
iii: Check your list of Network Components. If TCP/IP is not installed, click the Add button to install it now. If
TCP/IP is installed, go to step 6.
iv: In the Network Component Type dialog box, select Protocol and click Add button.
v: In the Select Network Protocol dialog box, select Microsoft and TCP/IP and then click the OK button to start
installing the TCP/IP protocol. You may need your Windows CD to complete the installation.
vi: After installing TCP/IP, go back to the Network dialog box. Select TCP/IP from the list of Network
Components and then click the Properties button.
vii: Check each of the tabs and verify the following settings:
•
•
•
•
•
Bindings: Check Client for Microsoft Networks and File and printer sharing for Microsoft Networks.
Gateway: All fields are blank.
DNS Configuration: Select Disable DNS.
WINS Configuration: Select Disable WINS Resolution.
IP Address: Select Obtain IP address automatically.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 0.3
viii: Reboot the PC. Your PC will now obtain an IP address automatically from your router’s DHCP server.
Note: Please make sure that the router’s DHCP server is the only DHCP server available on your LAN. Once
you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3.
2b) Windows 2000
i: Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.
ii: Double-click the Network and Dial-up Connections icon. In the Network and Dial-up Connection window,
double-click the Local Area Connection icon. The Local Area Connection window will appear.
iii: In the Local Area Connection window, click the Properties button.
iv: Check your list of Network Components. You should see Internet Protocol [TCP/IP] on your list. Select it
and click the Properties button.
v: In the Internet Protocol (TCP/IP) Properties window, select Obtain an IP address automatically and Obtain
DNS server address automatically as shown on the following screen.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 0.4
vi: Click OK to confirm the settings. Your PC will now obtain an IP address automatically from your router’s
DHCP server.
Note: Please make sure that the router’s DHCP server is the only DHCP server available on your LAN. Once
you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3.
2c) Windows NT
i: Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.
ii: Double-click the Network icon. The Network window will appear. Select the Protocol tab from the Network
window.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
iii: Check if the TCP/IP Protocol is on your list of Network Protocols. If TCP/IP is not installed, click the Add
button to install it now. If TCP/IP is installed, go to step 5.
iv: In the Select Network Protocol window, select the TCP/IP Protocol and click the Ok button to start installing
the TCP/IP protocol. You may need your Windows CD to complete the installation.
v: After you install TCP/IP, go back to the Network window. Select TCP/IP from the list of Network Protocols
and then click the Properties button.
vi: Check each of the tabs and verify the following settings:
•
•
•
•
IP Address: Select Obtain an IP address from a DHCP server.
DNS: all fields are blank.
WINS: all fields are blank.
Routing: all fields are blank.
Figure 0.4
13
Download from Www.Somanuals.com. All Manuals Search And Download.
vii: Click OK to confirm the settings. Your PC will now obtain an IP address automatically from your router’s
DHCP server.
Note: Please make sure that the router’s DHCP server is the only DHCP server available on your LAN. Once
you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3.
3)
4)
Once you have configured your PCs to obtain an IP address automatically, the router’s DHCP server will
automatically give your LAN clients IP addresses. By default, the router’s DHCP server is enabled so that you
can obtain an IP address automatically. To see if you have obtained an IP address, see Appendix A.
Note: Please make sure that the router’s DHCP server is the only DHCP server available on your LAN. If there is
another DHCP server on your network, then you’ll need to switch one of the DHCP servers off. (To disable the
router’s DHCP server, see Chapter 2: LAN Port.)
Once your PC has obtained an IP address from your router, enter the router’s default IP address of “192.168.2.1”
into your PC’s web browser and press Enter.
Figure 0.5
5)
The login screen below will appear. Enter the “User Name” and “Password” and then click <OK> to login.
Note: By default the user name is “admin” and the password is “1234”. For security reasons it is recommended
that you change the password as soon as possible (in General setup/system/password, see chapter 2)
Figure 0.6
14
Download from Www.Somanuals.com. All Manuals Search And Download.
6)
The HOME page screen below will appear. The Home Page is divided into four sections, Quick Setup Wizard,
General Setup, Status Information and Tools.
Quick Setup Wizard (Chapter 1)
If you only want to start using the router as an Internet Access device then you ONLY need to configure the
screens in the Quick Setup Wizard section.
General Setup (Chapter 2)
If you want to use more advanced features that the router has to offer, then you will need to configure the Quick
Setup Wizard and the General Setup section. Alternatively, you can just configure the General Setup section,
since the General Setup/WAN and the Quick Setup Wizard contain the same configurations.
Status Information (Chapter 3)
The Status Information section is for you to monitor the router’s status information at any point in time.
Tools (Chapter 4)
If you want to Reset the router (because of problems) or save your configurations or upgrade the firmware then
you will need to go to the Tools section.
Figure 0.7
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
Description
Quick Setup Wizard (Chapter 1)
Select your Internet connection type and then input the configurations
needed to connect to your Internet Service Provider (ISP).
General Setup (Chapter 2)
This section contains configurations for the Broadband router’s advanced
functions such as: Bridge, Address Mapping, Virtual Server, Access
Control, Hacker Attack Prevention, DMZ, Special applications and other
functions to meet your LAN requirements.
Status Information (Chapter 3)
Tools (Chapter 4)
In this section you can see the Broadband router's system information,
Internet Connection, Device Status, Security Log and DHCP client Log
information.
This section contains the router’s Tools - Tools include Configuration
tools, Firmware upgrade and Reset. Configuration tools allow you to
Backup (save), Restore, or Restore to Factory Default configuration for
your Broadband router. The Firmware upgrade tool allows you to
upgrade your router's firmware. The RESET tool allows you to reset your
Broadband router.
Logout
Selecting logout will return you to the LOGIN page
7)
Click on Quick Setup Wizard (see Chapter 1) to start configuring settings required by your ISP so that you can
start accessing the Internet. The other sections (General Setup, Status Information and Tools) do not need to be
configured unless you wish to implement/monitor more advanced features/information.
Select the section (Quick Setup Wizard, General Setup, Status Information and Tools) you wish to configure and
proceed to the corresponding chapter. Use the selections on the web management’s top right hand page (see
below) to navigate around the web-based management User Interface.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 0.8
17
Download from Www.Somanuals.com. All Manuals Search And Download.
About Quick Setup
The Quick Setup section is designed to let you set up the router as quickly as possible. In the Quick Setup, you are
required to fill in only the information necessary to access the Internet. Once you click on the Quick Setup Wizard in
the homepage, you will see the screen below.
Step 1) Time Zone
The Time Zone allows your router to base its time on the settings configured here, this will affect functions such as Log
entries and Firewall settings.
Figure 1.1
Parameter
Description
Set Time Zone
Select the time zone of the country you are currently in. The router will set its
time based on your selection.
Time Server Address
You can manually assign the time server address if the default time server does
not work.
Enable Daylight Savings
The router can also take Daylight savings into account. If you wish to use this
function, you must check the “Enable Daylight Savings” box to enable your
daylight savings configuration (below).
Start Daylight Savings Time
End Daylight Savings Time
Select the period in which you wish to start daylight Savings Time
Select the period in which you wish to end daylight Savings Time
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Click on NEXT to proceed to the next page (step 2).
Step 2) Broadband Type
In this section, you have to select one of four types of connections that you will be using to connect your router’s WAN
port to your ISP (see screen below).
Note: Different ISP’s require different methods of connecting to the Internet. Please check with your ISP as to the type of
connection it requires.
Figure 1.2
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
Description
1.1 Cable Modem
1.2 Fixed-IP xDSL
1.3 PPPoE
Your ISP will automatically give you an IP address
Your ISP has given you an IP address already
Your ISP requires you to use a Point-to-Point Protocol over Ethernet (PPPoE)
connection.
1.4 PPTP
Your ISP requires you to use a Point-to-Point Tunneling Protocol (PPTP) connection.
Click on one of the WAN types and then proceed to the manual’s relevant sub-section (1.1, 1.2, 1.3 or 1.4). Click on
Back to return to the previous screen.
1.1 Cable Modem
Choose Cable Modem if your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in
additional information such as Host Name and MAC address (see screen below).
Note: The Host Name and MAC address section is optional and you can skip this section if your ISP does not require
these settings for you to connect to the Internet.
Figure 1.3
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameters
Host Name
Description
If your ISP requires a Host Name, type in the host name provided by your ISP; otherwise
leave it blank if your ISP does not require a Host Name.
MAC Address
Your ISP may require a particular MAC address in order for you to connect to the
Internet. This MAC address is the PC’s MAC address that your ISP had originally
connected your Internet connection to. Type in this MAC address in this section or use
the “Clone MAC Address” button to replace the WAN MAC address with the MAC
address of that PC (you have to be using that PC for the Clone MAC Address button to
work). To find out the PC’s MAC address see Appendix A. (See Glossary for an
explanation on MAC addresses.)
Click OK when you have finished the configuration above. You have now completed the configuration for the Cable
Modem connection. You can start using the router now. If you wish to use some of the advanced features supported by
this router, see Chapters 2, 3, 4.
1.2 Fixed-IP xDSL
Select “Fixed-IP xDSL” if your ISP has given you a specific IP address for you to use. Your ISP should provide all the
information required in this section.
Figure 1.4
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameters
IP
Description
This is the IP address that your ISP has given you.
This is the ISP’s IP address gateway
This is the ISP’s DNS server IP address
Gateway IP
DNS
Subnet Mask
Enter the Subnet Mask provided by your ISP
(e.g. 255.255.255.0)
Click OK when you have finished the configuration above. You have now completed the configuration for the Fixed-IP
xDSL connection. You can start using the router now. If you wish to use some of the advanced features supported by this
router, see Chapters 2, 3, 4.
1.3 PPPoE
Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. Your ISP should provide all the
information required in this section.
Figure 1.5
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
User Name
Password
Enter the User Name provided by your ISP for the PPPoE connection
Enter the Password provided by your ISP for the PPPoE connection
Service Name
This is optional. Enter the Service name should your ISP require it. Otherwise, leave it
blank.
MTU
This is optional. You can specify the maximum size of your transmission packet to the
Internet. Leave it as it is if you do not wish to set a maximum packet size.
Connection Type
If you select “Continuous”, the router will always be connected to the ISP/Internet. If the
WAN line breaks down and links again, the router will auto-reconnect to the ISP. If you
select “Connect On Demand”, the router will auto-connect to the ISP when someone
wants to use the Internet and keep connected until the WAN idle timeout. The router will
close the WAN connection if the time period during which no one has been using the
Internet exceeds the “Idle Time”. If you select “Manual”, the router will connect to the
ISP only when you click “Connect” manually from the Web user interface. The WAN
connection will not get disconnected due to the idle timeout. If the WAN line breaks
down and later links again, the router will not auto-connect to the ISP.
Idle Time
You can specify an idle time threshold (in minutes) for the WAN port. This means if no
packets have been sent (no one is using the Internet) during this specified period, the
router will automatically disconnect the connection to the ISP/Internet.
Note: The WAN "idle timeout" auto-disconnect function may not work due to abnormal
activities of some network application software, computer viruses or hacker attacks from
the Internet. For example, some software sends network packets to the Internet in the
background, even when you are not using the Internet. This function also may not work
with some ISPs. Please make sure this function can work properly when you use this
function the first time, especially if your ISP charges you by time used. Due to various
uncontrollable issues, we cannot guarantee the WAN "idle timeout" auto-disconnect
function will always work. In order to prevent an extra fee from being charged by your
ISP, please turn off the router when you are finished using the Internet.
Click OK when you have finished the configuration above. You have now completed the configuration for the PPPoE
connection. You can start using the router now. If you wish to use some of the advanced features supported by this
router, see Chapters 2, 3, 4.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 PPTP
Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. Your ISP should provide all the
information required in this section.
Figure 1.6
Parameter
Description
Obtain an IP address
The ISP requires you to obtain an IP address by DHCP automatically before connecting
to the PPTP server.
Use the following IP address
IP Address
The ISP gives you a static IP to be used to connect to the PPTP server.
This is the IP address that your ISP has given you to establish a PPTP connection.
Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0)
Enter the IP address of the ISP Gateway
Subnet Mask
Default Gateway
24
Download from Www.Somanuals.com. All Manuals Search And Download.
User ID
Enter the User Name provided by your ISP for the PPTP connection (sometimes called a
Connection ID).
Password
Enter the Password provided by your ISP for the PPTP connection.
PPTP Gateway
If your LAN has a PPTP gateway, then enter that PPTP gateway IP address here. If you
do not have a PPTP gateway then enter the ISP’s Gateway IP address above.
Connection ID
MTU
This is the ID given by ISP. This is optional.
This is optional. You can specify the maximum size of your transmission packet to the
Internet. Leave it as it is if you do not wish to set a maximum packet size.
BEZEQ-ISRAEL
Connection Type
Select this item if you are using the service provided by BEZEQ in Israel.
If you select “Continuous”, the router will always be connected to the ISP/Internet. If the
WAN line breaks down and links again, the router will auto-reconnect to the ISP. If you
select “Connect On Demand”, the router will auto-connect to the ISP when someone
wants to use the Internet and keep connected until the WAN idle timeout. The router will
close the WAN connection if the time period during which no one has been using the
Internet exceeds the “Idle Time”. If you select “Manual”, the router will connect to the
ISP only when you click “Connect” manually from the Web user interface. The WAN
connection will not get disconnected due to the idle timeout. If the WAN line breaks
down and later links again, the router will not auto-connect to the ISP.
Idle Time
You can specify an idle time threshold (in minutes) for the WAN port. This means if no
packets have been sent (no one is using the Internet) during this specified period, the
router will automatically disconnect the connection to the ISP/Internet.
Note: The WAN "idle timeout" auto-disconnect function may not work due to abnormal
activities of some network application software, computer viruses or hacker attacks from
the Internet. For example, some software sends network packets to the Internet in the
background, even when you are not using the Internet. This function also may not work
with some ISPs. Please make sure this function can work properly when you use this
function the first time, especially if your ISP charges you by time used. Due to various
uncontrollable issues, we cannot guarantee the WAN "idle timeout" auto-disconnect
function will always work. In order to prevent an extra fee from being charged by your
ISP, please turn off the router when you are finished using the Internet.
Click OK when you have finished the configuration above. You have now completed the configuration for the PPTP
connection. You can start using the router now. If you wish to use some of the advanced features supported by this router,
see Chapters 2, 3, 4.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
General Settings
Once you click on the General Setup button on the homepage, you will see the screen below.
If you have already configured the Quick Setup Wizard, you do NOT need to configure anything in the General Setup
screen in order to start using the Internet.
The General Setup contains advanced features that allow you to configure the router to meet your network’s needs such
as: Address Mapping, Virtual Server, Access Control, Hacker Attack Prevention, Special Applications, DMZ and other
functions.
Figure 2.1
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Below is a general description of what advanced functions are available for this broadband router.
Menu
Description
2.1 System
This section allows you to set the Broadband router’s system Time Zone, Password and
Remote Management Administrator.
2.2 WAN
2.3 LAN
2.4 NAT
This section allows you to select the connection method in order to establish a connection
with your ISP (same as the Quick Setup Wizard section)
You can specify the LAN segment’s IP address, subnet Mask, enable/disable DHCP and
select an IP range for your LAN
You can configure the Address Mapping, Virtual Server and Special Applications
functions in this section. This allows you to specify what user/packet can pass your
router’s NAT.
2.5 Firewall
The Firewall section allows you to configure Access Control, Hacker Prevention and
DMZ.
Select one of the General Setup selections from above and proceed to the manual’s relevant sub-sections.
2.1 System
The system screen allows you to specify a time zone, to change the system password and to specify a remote management
user for the broadband router.
Figure 2.2
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameters
Description
System Settings
2.1.1 Time Zone
Select the time zone of the country you are currently in. The router will set its
time based on your selection.
2.1.2 Password Settings
2.1.3 Remote Management
Allows you to select a password in order to access the web-based management
website.
You can specify a Host IP address that can perform remote management
functions.
Select one of the above three system settings selections and proceed to the manual’s relevant sub-sections.
2.1.1 Time Zone
The Time Zone allows your router to reference or base its time on the settings configured here, which will affect functions
such as Log entries and Firewall settings.
Figure 2.3
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
Set Time Zone
Select the time zone of the country you are currently in. The router will set its
time based on your selection.
Time Server Address
You can manually assign time server address if the default time server dose not
work.
Enable Daylight Savings
The router can also take Daylight savings into account. If you wish to use this
function, you must check/tick the enable box to enable your daylight saving
configuration (below).
Start Daylight Savings Time
End Daylight Savings Time
Select the period in which you wish to start daylight Savings Time
Select the period in which you wish to end daylight Savings Time
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advance sections
or start using the router (with the advance settings in place)
2.1.2 Password Settings
You can change the password required to log into the broadband router's system web-based management. By default, the
password is “1234”. So please assign a password to the Administrator as soon as possible, and store it in a safe place.
Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive.
\
Figure 2.4
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameters
Description
Current Password
Enter your current password for the remote management administrator to log in to your
router.
Note: By default, the password is “1234”
New Password
Enter your new password
Re-Enter Password
for Verification
Enter your new password again for verification purposes
Note: If you forget your password, you will have to reset the router to the factory default
(password is “1234”) with the reset button (see router’s back panel).
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
2.1.3 Remote Management
The remote management function allows you to provide a host on the Internet with the ability to configure the router from
a remote site. Enter the designated host IP Address in the Host IP Address field.
Figure 2.5
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameters
Description
Host Address
This is the IP address of the host on the Internet that will have management/configuration access
to the Broadband router from a remote site. This means if you are at home and your home IP
address has been designated the Remote Management host IP address for this router (located in
your company office), then you are able to configure this router from your home. If the Host
Address is left 0.0.0.0 this means anyone can access the router’s web-based configuration from a
remote location, provided that they know the password.
Click the Enabled box to enable the Remote Management function.
Note: When you want to access the web-based management from a remote site, you must enter
the router’s WAN IP address (e.g. 10.0.0.1) into your web-browser followed by port number
8080, e.g. 10.0.0.1:8080 (see below). You’ll also need to know the password set in the Password
Setting screen in order to access the router’s web-based management.
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
2.2 WAN
Use the WAN Settings screen if you have already configured the router via the Quick Setup Wizard section and you
would like to change your Internet connection type. The WAN Settings screen allows you to specify the type of WAN
port connection you want to establish with your ISP. In the WAN Settings screen, you can also configure the router to
act as a bridge. The WAN settings offer the following selections for the router’s WAN port: Dynamic IP, Static IP,
PPPoE, PPTP, L2TP, Telstra Big Pond, Policy, DNS and DDNS. You will need to select one of the two WAN ports
first and configure one WAN port at a time.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2.6
Parameters
Description
2.2.1 Dynamic IP address
Your ISP will automatically give you an IP address
Your ISP has given you an IP address already
Your ISP requires PPPoE connection.
2.2.2 Static IP address
2.2.3 PPPoE
2.2.4 PPTP
Your ISP requires you to use a Point-to-Point Tunneling Protocol (PPTP)
connection.
2.2.5 L2TP
Your ISP requires L2TP connection.
2.2.6 Telstra Big Pond
2.2.7 Policy
Your ISP requires Telstra Big Pond connection.
You can configure WAN policy.
2.2.8 DNS
You can specify a DNS server that you wish to use
2.2.9 DDNS
You can specify a DDNS server that you wish to use and configure the user name
and password provided by your DDNS service provider.
Once you have made a selection, click More Configuration at the bottom of the screen and proceed to the manual’s
relevant sub-sections.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.1 Dynamic IP Address
Choose the Dynamic IP selection if your ISP will give you an IP address automatically. Some ISP’s may also require that
you fill in additional information such as Host Name, Domain Name and MAC address. (See Chapter 1: “Cable Modem”
for more details.)
2.2.2 Static IP Address
Choose the Static IP selection if your ISP has given you a specific IP address for you to use. Your ISP should provide all
the information required in this section. (See Chapter 1: “Fixed IP” for more details.)
2.2.3 PPPoE (PPP over Ethernet)
Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. Your ISP should provide all the
information required in this section. (See chapter 1 “PPPoE” for more details.)
2.2.4 PPTP
Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. Your ISP should provide all the
information required in this section. (See chapter 1: “PPTP” for more details.)
2.2.5 L2TP
Select L2TP if your ISP requires the L2TP protocol to connect you to the Internet. Your ISP should provide all the
information required in this section.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2.7
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
Obtain an IP address
The ISP requires you to obtain an IP address by DHCP automatically
before connecting to the L2TP server.
MAC Address
Your ISP may require a particular MAC address in order for you to connect to the
Internet. This MAC address is the PC's MAC address that your ISP had originally
connected your Internet connection to. Type in this MAC address in this section or use
the "Clone MAC Address" button to replace the WAN MAC address with the MAC
address of that PC (you have to be using that PC for the Clone MAC Address button to
work). To find out the PC's MAC address see Appendix A. (see Glossary for an
explanation on MAC address)
Use the following IP address
IP Address
The ISP gives you a static IP address to be used to connect to the L2TP server.
This is the IP address that your ISP has given you to establish an L2TP connection.
Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0)
Enter the IP address of the ISP Gateway
Subnet Mask
Gateway
User ID
Enter the User Name provided by your ISP for the PPTP connection. Sometimes called a
Connection ID
Password
Enter the Password provided by your ISP for the PPTP connection
L2TP Gateway
If your LAN has an L2TP gateway, then enter that L2TP gateway IP address here. If you
do not have an L2TP gateway, then enter the ISP’s Gateway IP address above.
MTU
This is optional. You can specify the maximum size of your transmission packet to the
Internet. Leave it as it is if you do not wish to set a maximum packet size.
Connection Type
If you select “Continuous”, the router will always connect to the ISP. If the WAN line
breaks down and links again, the router will auto-reconnect to the ISP.
If you select “Connect On Demand”, the router will auto-connect to the ISP when
someone want to use the Internet and keep connected until the WAN idle timeout. The
router will close the WAN connection if the time period that no one is using the Internet
exceeds the “Idle Time”.
If you select “Manual”, the router will connect to ISP only when you click “Connect”
manually from the Web user interface. The WAN connection will not disconnected due
to the idle timeout. If the WAN line breaks down and latter links again, the router will not
auto-connect to the ISP.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Idle Time Out
Note: The WAN "idle timeout" auto-disconnect function may not work due to abnormal
activities of some network application software, computer viruses or hacker attacks from
the Internet. For example, some software sends network packets to the Internet in the
background, even when you are not using the Internet. This function also may not work
with some ISPs. Please make sure this function can work properly when you use this
function the first time, especially if your ISP charges you by time used. Due to various
uncontrollable issues, we cannot guarantee the WAN "idle timeout" auto-disconnect
function will always work. In order to prevent an extra fee from being charged by your
ISP, please turn off the router when you are finished using the Internet.
Click OK when you have finished the configuration above. You have now completed the configuration for the L2TP
connection. You can start using the router now. If you wish to use some of the advanced features supported by this
router, see Chapters 2, 3, 4.
2.2.6 Telstra Big Pond
Select Telstra Big Pond if your ISP requires the Telstra Big Pond protocol to connect you to the Internet. Your ISP should
provide all the information required in this section. Telstra Big Pond protocol is used by ISPs in Australia.
Figure 2.8
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
User Name
Password
Description
Enter the User Name provided by your ISP for the Telstra Big Pond connection
Enter the Password provided by your ISP for the Telstra Big Pond connection
User decide login server
server manually
Select if you want to assign the IP of Telstra Big Pond’s login
server manually.
Login Server
The IP of the Login Server.
Click OK when you have finished the configuration above. You have now completed the configuration for the Telstra
Big Pond connection. You can start using the router now. If you wish to use some of the advanced features supported by
this router, see Chapters 2, 3, 4.
2.2.7 WAN Policy
The WAN policy for multi-homing can be setup here. You can set up policy for each WAN separately. The router will
balance the load between all active WAN ports according to the Send/Receive rate of the WAN ports. You can setup an
IP address for the router to detect if the WAN line is connected. If the router fails to ping the IP, it would recognize the
WAN line as not connected, and will stop directing the Internet traffic to this WAN port. The traffic will be redirected to
the other active WAN port. The Intranet users will not become aware of this change and keep surfing the Internet
smoothly. You also can setup a WAN port as a backup WAN port. A backup WAN port would not be activated when the
router starts up. When the other active WAN port fails to connect to the Internet, the backup WAN port will be activated
and take over all the traffic.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2.9
Parameter
Speed
Description
The send/upstream and receive/downstream speed of the WAN line the
WAN port is connected to.
Connectivity check
Operation
You can key in an IP. The router will ping that IP to verify if the WAN
line can access the Internet. You also can select “Ping Default Gateway”,
and the router will check if the WAN line is ok by ping the default
gateway of the WAN port.
If you select “Enable”, the WAN port will be activated when the system
boot up. If you select “Backup”, the WAN port is disabled on start up.
But when other enabled WAN ports fail, the backup WAN port will be
activated and take over all the traffic.
2.2.8 DNS
A Domain Name System (DNS) server is like an index of IP addresses and Web addresses. If you type a Web address
Most ISPs provide a DNS server for speed and convenience. If your Service Provider connects you to the Internet with
38
Download from Www.Somanuals.com. All Manuals Search And Download.
dynamic IP settings, it is likely that the DNS server IP address is provided automatically. However, if there is a DNS
server that you would rather use, you need to specify the IP address of that DNS server here.
Figure 2.10
Parameters
Description
Domain Name Server (DNS) Server
This is the ISP’s DNS server IP address that they gave you; or you can
specify your own preferred DNS server IP address
Secondary DNS Address (optional)
This is optional. You can enter another DNS server’s IP address as a
backup. The secondary DNS will be used should the above DNS fail.
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
2.2.9 DDNS
DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your
static domain name from the DDNS service providers. You can assign a DDNS server for each WAN port. This router
supports some DDNS service providers, for example DynDNS and TZO.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2.11
Parameters
WAN Port
Default
Description
Select the WAN port that you want to configure the DDNS for
Enable/Disable
Provider
Disable
Enable/Disable the DDNS function of this router
Select a DDNS service provider
DynDNS
Domain name
Account/E-mail
Password/Key
Your static domain name that use DDNS
The account that your DDNS service provider assigned to you
The password you set for the DDNS service account above
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
40
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 LAN
The LAN Port screen below allows you to specify a private IP address for your router’s LAN ports as well as a subnet
mask for your LAN segment.
Figure 2.12
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameters
Default
Description
LAN
IP address
192.168.2.1
This is the router’s LAN port (private) IP address (Your LAN clients’
default gateway IP address)
IP Subnet Mask
255.255.255.0
Disabled
Specifies a Subnet Mask for your LAN segment
802.1d Spanning
Tree
If the 802.1d Spanning Tree function is enabled, this router will use the
spanning tree protocol to prevent network loops from occurring among
the LAN ports.
DHCP Server
Lease Time
Enabled
You can enable or disable the DHCP server. By enabling the DHCP
server, the router will automatically give your LAN clients an IP address.
If the DHCP is not enabled then you’ll have to manually set your LAN
clients’ IP addresses; make sure the LAN Client is in the same subnet as
the router if you want the router to be your LAN clients’ default gateway
When DHCP is enabled, it will temporarily give your LAN clients an IP
address. In the Lease Time setting you can specify the time period that
the DHCP lends an IP address to your LAN clients. The DHCP will
change your LAN client’s IP address when this time threshold period is
reached
IP Address Pool
You can select a particular IP address range for your DHCP server to
issue IP addresses to your LAN Clients.
Note: By default the IP range is from: Start IP 192.168.2.100 to End IP
192.168.2.199. If you want your PC to have a static/fixed IP address then
you’ll have to choose an IP address outside this IP address Pool
Domain Name
You can specify a Domain Name for your LAN
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
42
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 NAT
Network Address Translation (NAT) allows multiple users at your local site to access the Internet through a single Public
IP Address or multiple Public IP Addresses. NAT provides Firewall protection from hacker attacks and has the flexibility
to allow you to map Private IP Addresses to Public IP Addresses for key services such as Websites and FTP. You also can
disable NAT function and use the static route.
Figure 2.13
Parameter
Description
Enable or Disable NAT
You can enable NAT to let the router provide the IP sharing function or disable
NAT to use the static routing function.
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
43
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.1 Port Forwarding
The Port Forwarding allows you to re-direct a particular range of service port numbers (from the Internet/WAN Ports) to a
particular LAN IP address. It helps you to host some servers behind the router NAT firewall.
Figure 2.14
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameter
Description
Enable Port Forwarding
Enable Port Forwarding
Private IP
This is the private IP of the server behind the NAT firewall.
Note: You need to give your LAN PC clients a fixed/static IP address for
Port Forwarding to work properly.
Type
This is the protocol type to be forwarded. You can choose to forward
“TCP” or “UDP” packets only or select “both” to forward both “TCP”
and “UDP” packets.
Port Range
WAN Port
The range of ports to be forward to the private IP.
Assign the WAN port that requires port forwarding. All the packets sent
from this WAN port with the assigned port range will be directed to the
assigned private IP addresses.
Comment
The description of this setting.
Add Port Forwarding into the table
Fill in the "Private IP", “Type”, “Port Range”, “WAN Port” and
"Comment" of the settings to be added and then click "Add". Then this
Port Forwarding setting will be added into the "Current Port Forwarding
Table" below. If you find any errors before adding it and want to type it
in again, just click "Clear" and the fields will be cleared.
Remove Port Forwarding into the table
If you want to remove some Port Forwarding settings from the " Current
Port Forwarding Table", select the Port Forwarding settings you want to
remove in the table and then click "Delete Selected". If you want to
remove all Port Forwarding settings from the table, just click the "Delete
All" button. Clicking "Reset" will clear your current selections.
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
45
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.2 Virtual Server
Use the Virtual Server function when you want different servers/clients in your LAN to handle different service/Internet
application type (e.g. Email, FTP, Web server etc.) from the Internet. Computers use numbers called port numbers to
recognize a particular service/Internet application type. The Virtual Server allows you to re-direct a particular service port
number (from the Internet/WAN Port) to a particular LAN private IP address and its service port number. (See Glossary
for an explanation on Port number)
Figure 2.15
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameters
Description
Enable Virtual Server
Private IP
Enable Virtual Server.
This is the LAN client/host IP address that the Public Port number packet will be sent to.
Note: You need to give your LAN PC clients a fixed/static IP address for the Virtual
Server function to work properly.
Private Port
Type
This is the port number (of the above Private IP host) that the below Public Port number
will be changed to when the packet enters your LAN (to the LAN Server/Client IP)
Select the port number protocol type (TCP, UDP or both). If you are unsure, then leave it
to the default “Both” protocol.
Public Port
Enter the service (service/Internet application) port number from the Internet that will be
re-directed to the above Private IP address host in your LAN
Note: Virtual Server function will have priority over the DMZ function if there is a
conflict between the Virtual Server and the DMZ settings.
WAN Port
Assign the WAN port that you want to bind to the virtual server. All the packets sending
from this WAN port with the assigned public port will be directed to the assigned private
IP and private port.
Comment
The description of this setting.
Add Virtual Server
Fill in the "Private IP", "Private Port", "Type", “Public Port”, “WAN Port” and
"Comment" of the setting to be added and then click "Add". Then this Virtual Server
setting will be added into the "Current Virtual Server Table" below. If you find any
errors before adding it and want to retype again, just click "Clear" and the fields will be
cleared.
Remove Virtual Server
If you want to remove some Virtual Server settings from the "Current Virtual Server
Table", select the Virtual Server settings you want to remove in the table and then click
"Delete Selected". If you want remove all Virtual Server settings from the table, just
click the "Delete All" button. Clicking "Reset" will clear your current selections.
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
Example: Virtual Server
The diagram below demonstrates one of the ways you can use the Virtual Server function. Use Virtual Server when you
want the web server located in your private LAN to be accessible to Internet users from WAN 2. The configuration below
means that any request coming form the Internet to access your web server will be translated to your LAN’s web server
(192.168.2.2). Note: For the virtual server to work properly Internet/remote users must know your global IP
47
Download from Www.Somanuals.com. All Manuals Search And Download.
address for WAN 2. (For websites, you will need to have a fixed/static global/public IP address or use DDNS with
dynamic IP and domain name mapping.)
Figure 2.16
2.4.3 Special Applications
Some applications require multiple connections, such as Internet games, video conferencing, Internet telephony and
others. In this section you can configure the router to support multiple connections for these types of applications.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2.17
Parameters
Description
Enable Trigger Port
Trigger Port
Enables the Special Application function.
This is the outgoing (Outbound) range of port numbers for this particular application
Select whether the outbound port protocol is “TCP”, “UDP” or both.
Trigger Type
Public Port
Enter the In-coming (Inbound) port or port range for this type of application (e.g. 2300-
2400, 47624)
Note: Individual port numbers are separated by a comma
(e.g. 47624, 5775, 6541 etc.). To input a port range use a “dash” to separate the two port
number range (e.g. 2300-2400)
Public Type
Comment
Select the Inbound port protocol type: “TCP”, “UDP” or both
The description of this setting.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Popular applications
This section lists the more popular applications that require multiple connections. Select
an application from the Popular Applications selection. Once you have selected an
application, select a location (1-10) in the Copy to selection box and then click the Copy
to button. This will automatically list the Public Ports required for this popular
application in the location (1-10) you had specified.
Add Special Application
Fill in the "Trigger Port", "Trigger Type”, “Public Port”, "Public Type", and "Comment"
of the setting to be added and then click "Add". This Special Application setting will
then be added into the "Current Trigger-Port Table" below. If you find any errors before
adding it and want to retype it again, just click "Clear" and the fields will be cleared. If
you want to add a popular application, select one “Popular Application” and then click
“Add”.
Remove Special Application
If you want to remove some Special Application settings from the "Current Trigger-Port
Table", select the Special Application settings you want to remove in the table and then
click "Delete Selected". If you want to remove all Special Application settings from the
table, just click the "Delete All" button. Clicking "Reset" will clear your current
selections.
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
Example: Special Applications
If you need to run applications that require multiple connections, then specify the port (outbound) normally associated
with that application in the "Trigger Port" field. Then select the protocol type (TCP or UDP) and enter the public ports
associated with the trigger port to open them up for inbound traffic.
Example:
Trigger
ID Trigger Port
Public Port
Public Type
Comment
Type
UDP
UDP
1
2
28800
6112
2300-2400, 47624
6112
TCP
UDP
MSN Game Zone
Battle.net
In the example above, when a user triggers port 28800 (outbound) for MSN Game Zone then the router will allow
incoming packets for ports 2300-2400 and 47624 to be directed to that user. Note: Only one LAN client can use a
particular special application at a time.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.4 UPnP
With UPnP, all PCs in your Intranet will discover/locate this router automatically. So you will not have to perform any
configuration procedures for your PC and can access the Internet through this router easily.
Figure 2.18
Parameters
Default
Disable
Description
UPnP Feature
You can Enable or Disable the UPnP feature here. After you enable the
UPnP feature, all client systems that support UPnP, like Windows XP,
can discover/locate this router automatically and access the Internet
through this router without any configuration. The NAT Traversal
function provided by UPnP can let applications that support UPnP
smoothly connect to Internet sites without any incompatibility problem
due to the NAPT port translation.
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
51
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.5 Protocol and Port Binding
Protocol and Port Binding let you manually bind an application to a WAN port. Only packets that match all the entered
criteria will be bound to the assigned WAN port. You will have to fill all the items. The items that you leave blank will
be ignored.
Figure 2.19
Parameters
Description
Enable Protocol &
Port Binding
The “Protocol and Port Binding” function is disabled by default. You can select to
enable the “Protocol and Port Binding” function.
Source IP Range
Only packets with this assigned source IP range will statically bind to the assigned WAN
port.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Destination IP Range
Source Port Range
Only packets with this assigned destination IP range will statically bind to the assigned
WAN port.
Only packets with this assigned source port range will statically bind to the assigned
WAN port.
Destination Port Range
Only packets with this assigned destination port range will statically bind to the assigned
WAN port.
Protocol
Only packets with this assigned protocol will statically bind to the assigned WAN port.
The WAN port that the packets matching this rule are statically bound to.
WAN Port
Add a Rule
Fill in the "Source IP Range", "Destination IP Range”, “Source Port Range”, "Destination
Port Range", "Protocol" or "WAN Port" of the setting to be added and then click "Add".
This rule of Protocol and Port Binding will then be added into the "Protocol and Port
Binding Table" below. If you find any errors before adding it and want to retype it again,
just click "Clear" and the fields will be cleared.
Remove a Rule
If you want to remove a rule from the "Protocol and Port Binding Table", select the rules
you want to remove in the table and then click "Delete Selected". If you want to remove
all rules from the table, just click the "Delete All" button. Clicking "Reset" will clear your
current selections.
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
53
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.6 ALG Settings
You can select applications that need “Application Layer Gateway” to support.
Figure 2.20
Parameters
Enable
Default
Description
You can enable the “Application Layer Gateway”. Then, the router will
let that application correctly pass though the NAT gateway.
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
54
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4.7 Static Routing
This router provides a Static Routing function when NAT is disabled. With Static Routing, the router can forward packets
according to your routing rules.
Note: The DMZ function of the firewall will not work if static routing is enabled.
Figure 2.21
Parameter
Description
Enable Static Routing
The Static Routing function is disabled by default. You have to enable the Static
Routing function before your routing rules take effect.
Destination LAN IP
Subnet Mask
The network address of the destination LAN.
The subnet mask of the destination LAN.
Default Gateway
The next stop gateway of the path toward the destination LAN. This is the IP
address of the neighbor router that this router should communicate with on the
path to the destination LAN.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Hop Count
Interface
The number of hops (routers) to pass through to reach the destination LAN.
The interface that goes to the next hop (router).
Add a Rule
Fill in the "Destination LAN IP", "Subnet Mask”, “Default Gateway”, "Hop
Count" and "Interface" of the rule to be added and then click "Add". This rule
for Static Routing will then be added into the "Static Routing Table" below. If
you find any errors before adding it and want to retype it again, just click "Clear"
and the fields will be cleared.
Remove a Rule
If you want to remove some routing rules from the "Static Routing Table", select
the rules you want to remove in the table and then click "Delete Selected". If you
want to remove all the rules from the table, just click the "Delete All" button.
Clicking "Reset" will clear your current selections.
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
2.5 Firewall
The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of
hacker attacks, and defending against a wide array of common Internet attacks. However, for applications that require
unrestricted access to the Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ).
Note: To enable the Firewall settings select Enable and click Apply.
Figure 2.22
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2.23
Parameters
Description
2.5.1 Access Control
Access Control allows you to specify which hosts/users can have access to certain
Internet applications.
2.5.2 URL Blocking
2.5.3 DoS
URL Blocking allows you to specify which URLs cannot be accessed by users.
The router's firewall can block common hacker attacks and can log the attack activities.
2.5.4 DMZ
The DMZ function allows you to re-direct all packets going to your WAN port IP address
to a particular IP address in your LAN.
Click on one of the firewall selections and proceed to the manual’s relevant sub-sections.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5.1 Access Control
If you want to restrict users from accessing certain Internet applications/services (e.g. Internet websites, email, FTP etc.),
you can change the relevant settings here. Access Control allows users to define the type of traffic permitted on your
LAN. You can control which PC client can have access to these services.
Figure 2.24
Parameters
Description
Filter client PCs by IP
Add PC
Fill “IP Filtering Table” to filter PC clients by IP.
You can click Add PC to add an access control rule for users by IP addresses.
Remove PC
If you want to remove some PC from the "IP Filtering Table", select the PC you
want to remove in the table and then click "Delete Selected". If you want remove
all PCs from the table, just click the "Delete All" button.
Filter client PC by MAC address
Check “Enable MAC Filtering” to enable MAC Filtering.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Add PC
Fill in “Client PC MAC Address” and “Comment” for the PC that will be
allowed to access the Internet, and then click “Add”. If you find any errors
before adding it and want to retype it again, just click "Reset" and the fields will
be cleared.
Remove PC
If you want to remove a PC from the "MAC Filtering Table", select the PC you
want to remove in the table and then click "Delete Selected". If you want to
remove all PCs from the table, just click the "Delete All" button. If you want to
clear the selection and re-select again, just click “Reset”.
You can now configure other advanced sections or start using the router (with the advanced settings in place).
Figure 2.25
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Add PC
Parameters
Description
Client PC Description
The description for this client PC rule.
Client PC IP Address
Client PC Service
Enter the IP address that you wish to apply the Access Control rule to. This is the
user’s IP address for which you wish to setup an Access Control rule.
Note: You need to give your LAN PC clients a fixed/static IP address for the
Access Control rule to work properly.
You can block the clients from accessing some Internet services by checking the
services you want to block.
Protocol
This allows you to select UDP, TCP or both protocol types you want to block.
Port Range
You can assign up to five port ranges. The router will block clients from
accessing Internet services that use these ports.
Apply Changes
Reset
Click “Apply Changes” to save the settings.
Click “Reset” to clear all fields.
Click Apply Changes at the bottom of the screen to save the above configurations. You can now configure other
advanced sections or start using the router (with the advanced settings in place).
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Example: Access Control
In the example below, LAN client A can only access websites that use Port 80. However, LAN client B is able to access
websites and any other service that uses ports between 80 and 999.
Figure 2.26
61
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5.2 URL Blocking
You can block access to some Web sites from particular PCs by entering a full URL address or just a keyword of the web
site.
Figure 2.27
Parameters
Description
Enable URL Blocking
Add URL Keyword
Enables/disables URL Blocking.
Fill in the “URL/Keyword” and then click “Add”. You can enter the full URL
address or the keyword of the web site you want to block. If you find any errors
before adding it and want to retype it again, just click "Reset" and the field will
be cleared.
Remove URL Keyword
If you want to remove a URL keyword from the "Current URL Blocking Table",
select the URL keyword you want to remove in the table and then click "Delete
Selected". If you want to remove all URL keywords from the table, just click the
"Delete All" button. If you want to clear the selection and re-select again, just
click “Reset”.
You can now configure other advanced sections or start using the router (with the advanced settings in place).
62
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5.3 DoS (Denial of Service)
The Broadband router's firewall can block common hacker attacks, including Ping of Death, Discard Ping from WAN,
Port Scan, and Sync Flood. If Internet attacks occur the router can log the events.
Figure 2.28
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2.29
Parameters
Description
Intrusion Detection Features
Ping of Death
Discard Ping From WAN
Port Scan
Protections from Ping of Death attacks. From the Advanced Settings
page, you can configure a threshold for the frequency of packet occurrence.
The router’s WAN port will not respond to any Ping requests
Protection from any Port Scan attacks. If you go to the Advanced Settings
page, you can configure the pattern of Port Scan you want to prevent.
Sync Flood
Protection from any Sync Flood attacks. If you go to the Advanced
Settings page, you can configure a threshold for the frequency of packet
occurrence.
Click Apply at the bottom of the screen to save the above configurations. You can now configure other advanced sections
or start using the router (with the advanced settings in place).
64
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5.4 DMZ
If you have a local client PC that cannot run an Internet application (e.g. Games) properly from behind the NAT firewall,
then you can open the client up to unrestricted two-way Internet access by defining a DMZ Host. The DMZ function
allows you to re-direct all packets going to your WAN port IP address to a particular IP address in your LAN. The
difference between the virtual server and the DMZ function is that the virtual server re-directs a particular service/Internet
application (e.g. FTP, websites) to a particular LAN client/server, whereas DMZ re-directs all packets (regardless of
services) going to your WAN IP address to a particular LAN client/server.
Note: DMZ function works only when the NAT function is enabled.
Figure 2.30
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameters
Description
Enable DMZ
Enables/disables DMZ.
Note: If there is a conflict between the Virtual Server and the DMZ setting, then the
Virtual Server function will have priority over the DMZ function.
WAN Port
The WAN port that the local client PC’s IP address will bind to.
Public IP Address
The IP address of the WAN port or any other Public IP addresses given to you by your
ISP. The WAN port may use dynamic IP or static IP given by your ISP. If your ISP
gives you more than one dynamic IP address, you have to assign the session number that
you want to apply.
Client PC IP Address
Input the IP address of a particular host in your LAN that will receive all the packets
originally going to the WAN port/Public IP address above.
Note: You need to give your LAN PC clients a fixed/static IP address for the DMZ
function to work properly.
Add DMZ
Fill in the "WAN Port", "Public IP Address” and “Client IP Address” of the DMZ to be
added and then click "Add". This DMZ entry will then be added into the "DMZ Table"
below. If you find any errors before adding it and want to retype it again, just click
"Clear" and the fields will be cleared.
Remove DMZ
If you want to remove a DMZ from the "DMZ Table", select the DMZ entries you want to
remove in the table and then click "Delete Selected". If you want to remove all DMZ
entries from the table, just click the "Delete All" button. Clicking "Reset" will clear your
current selections.
You can now configure other advanced sections or start using the router (with the advanced settings in place).
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Status
The Status section allows you to monitor the current status of your router. You can use the Status page to monitor: the
connection status of the router's WAN/LAN interfaces, the current firmware and hardware version numbers, any illegal
attempts to access your network, and information on all DHCP client PCs currently connected to your network.
Parameters
Description
3.1 Status and Information
3.2 Internet Connection
3.3 Device Status
3.4 System Log
Shows the router’s system information
View the router’s current Internet connection status and other related information
View the router’s current setting status
View the router’s system log
3.5 Security Log
View any attempts that have been made to illegally gain access to your network.
View your LAN client's information that is currently linked to the router's DHCP server
View the critical statistics
3.6 Active DHCP Client
3.7 Statistics
Select one of the above Status selections and proceed to the manual’s relevant sub-section.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1 Status and Information
The Status and Information section allows you to view the router’s system information.
Figure 3.1
Parameters
Information
Description
You can see the router’s system information, including the router’s: Hardware version,
Boot code Version, and Runtime code Version
68
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Internet Connection
View the router’s current Internet connection status and other related information.
Figure 3.2
Parameters
Description
Internet Connection
This page displays whether the WAN ports are connected to Cable/DSL connections. It
also displays the router’s WAN port: WAN IP address, Subnet Mask, and ISP Gateway
as well as the Primary DNS and Secondary DNS being used.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Device Status
View the router’s current configuration settings. The Device Status displays the configuration settings you have
configured in the Quick Setup Wizard/General Setup section.
Figure 3.3
Parameters
Description
Device Status
This page shows the router’s current device settings. This page displays the router LAN
port’s current LAN IP Address and Subnet Mask. It also shows whether the DHCP
Server is enabled.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4 System Log
View the operation log of the system.
Figure 3.4
Parameters
System Log
Description
This page shows the current system log of the Broadband router. It displays any event
occurred after system start up. At the bottom of the page, the system log can be saved
<Save> to a local file for further processing, or the system log can be cleared <Clear>,
or it can be refreshed <Refresh> to get the most updated status. When the system is
powered down, the system log will disappear if not saved to a local file.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
3.5 Security Log
View any attempts that have been made to illegally gain access to your network.
Figure 3.5
Parameters
Description
Security Log
This page shows the current security log of the Broadband router. It displays any illegal
attempts to access your network. At the bottom of the page, the security log can be saved
<Save> to a local file for further processing, or the security log can be cleared <Clear>,
or it can be refreshed <Refresh> to get the most updated status. When the system is
powered down, the security log will disappear if not saved to a local file.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6 Active DHCP Client
View your LAN client's information that is currently linked to the Broadband router's DHCP server
Figure 3.6
Parameters
Description
DHCP Client Log
This page shows all DHCP clients (LAN PCs) currently connected to your network. The
“Active DHCP Client Table” displays the IP address and the MAC address and Time
Expired for each LAN Client. Use the Refresh button to get the most updated status.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
3.7 Statistics
View the statistics of packets sent and received over each WAN and LAN interface.
Figure 3.7
Parameters
Statistics
Description
Shows the counters for packets sent and received over the WAN and LAN interfaces.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Tools
This page includes the basic configuration tools, such as Configuration Tools (save or restore configuration settings),
Firmware Upgrade (upgrade system firmware) and Reset.
Figure 4.1
Parameters
Description
4.1 Configuration Tools
You can save the router’s current configuration, restore the router’s saved configuration
files and restore the router’s factory default settings.
4.2 Firmware Upgrade
4.3 Reset
This page allows you to upgrade the router’s firmware.
You can reset the router’s system should any problems occur.
Select one of the above Tool Settings and proceed to the manual’s relevant sub-section.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Configuration Tools
The Configuration Tools screen allows you to save (back up) the router’s current configuration settings. Saving the
configuration settings provides an added protection and convenience if problems occur with the router and you have to
reset to the factory default. When you save (back up) the configuration settings, you can re-load the saved configuration
into the router through the Restore selection. If more serious problems occur, you can use the Restore to Factory Defaults
selection. This will set all configurations to their original default settings (i.e., when you first purchased the router).
Figure 4.2
Parameters
Description
Configuration Tools
Use the "Backup" tool to save the router’s current configuration to a file named
"config.bin" on your PC. You can then use the "Restore" tool to restore the saved
configuration to the router. Alternatively, you can use the "Restore to Factory
Defaults" tool to force the router to perform a power reset and restore the original factory
settings.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Firmware Upgrade
This page allows you to upgrade the router’s firmware
Figure 4.3
Parameters
Description
Firmware Upgrade
This tool allows you to upgrade the router’s system firmware. To upgrade your router’s
firmware, you need to download the firmware file to your local hard disk, and enter that
file name and path in the appropriate field on this page. You can also use the Browse
button to find the firmware file on your PC.
Once you have selected the new firmware file, click Apply at the bottom of the screen to start the upgrade process. (You
may have to wait a few minutes for the upgrade to complete). Once the upgrade is completed you can start using the
router.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Reset
You can reset the router’s system if any problems occur. The reset function essentially re-boots your router’s system.
Figure 4.4
Parameters
Reset
Description
In the event that the system stops responding correctly or in some way stops functioning,
you can perform a reset. Your settings will not be changed. To perform the reset, click
on the APPLY button. You will be asked to confirm your decision. The reset will be
complete when the power light stops blinking. Once the reset process is complete you
may start using the router again.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Manually Find Your PC’s IP and MAC Addresses
1) In Windows, open the Command Prompt program.
2) Type Ipconfig /all and click Enter.
•
•
•
Your PC’s IP address is the one entitled IP address (192.168.1.77)
The router’s IP address is the one entitled Default Gateway (192.168.1.254)
Your PC’s MAC Address is the one entitled Physical Address (00-50-FC-FE-02-DB)
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Bridge: A bridge is an intelligent, internetworking device that forwards or filters packets between different networks
based on data link layer (MAC) address information.
Default Gateway (Router): Every non-router IP device needs to configure a default gateway’s IP address. When the
device sends out an IP packet, if the destination is not on the same network, the device has to send the packet to its default
gateway, which will then send it out towards the destination.
DHCP: Dynamic Host Configuration Protocol. This protocol automatically gives every computer on your home network
an IP address.
DNS Server IP Address: DNS stands for Domain Name System, which allows Internet servers to have a domain name
(such as www.Broadbandrouter.com) and one or more IP addresses (such as 192.34.45.8). A DNS server keeps a
database of Internet servers and their respective domain names and IP addresses, so that when a domain name is requested
(as in typing "Broadbandrouter.com" into your Internet browser), the user is sent to the proper IP address. The DNS
server IP address used by the computers on your home network is the location of the DNS server your ISP has assigned to
you.
DSL Modem: DSL stands for Digital Subscriber Line. A DSL modem uses your existing phone lines to transmit data at
high speeds.
Ethernet: A standard for computer networks. Ethernet networks are connected by special cables and hubs, and move
data around at up to 10/100/1000 million bits per second (Mbps).
Idle Timeout: Idle Timeout is designed so that if there is no traffic to the Internet for a pre-configured amount of time,
the connection will automatically be disconnected.
IP Address and Network (Subnet) Mask: IP stands for Internet Protocol. An IP address consists of a series of four
numbers separated by periods, that identifies a single, unique Internet computer host in an IP network. Example:
192.168.2.1. It consists of 2 portions: the IP network address, and the host identifier.
The IP address is a 32-bit binary pattern, which can be represented as four cascaded decimal numbers separated by “.”:
aaa.aaa.aaa.aaa, where each “aaa” can be anything from 000 to 255, or as four cascaded binary numbers separated by “.”:
bbbbbbbb.bbbbbbbb.bbbbbbbb.bbbbbbbb, where each “b” can either be 0 or 1.
A network mask is also a 32-bit binary pattern, and consists of consecutive leading
1’s followed by consecutive trailing 0’s, such as
11111111.11111111.11111111.00000000. Therefore sometimes a network mask can also be described simply as “x”
number of leading 1’s.
When both are represented side by side in their binary forms, all bits in the IP address that correspond to 1’s in the
network mask become part of the IP network address, and the remaining bits correspond to the host ID.
For example, if the IP address for a device is, in its binary form,
11011001.10110000.10010000.00000111, and if its network mask is,
11111111.11111111.11110000.00000000
It means the device’s network address is
11011001.10110000.10010000.00000000, and its host ID is,
00000000.00000000.00000000.00000111. This is a convenient and efficient method for routers to route IP packets to their
destination.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
ISP Gateway Address: (see ISP for definition). The ISP Gateway Address is an IP address for the Internet router located
at the ISP's office.
ISP: Internet Service Provider. An ISP is a business that provides connectivity to the Internet for individuals and other
businesses or organizations.
LAN: Local Area Network. A LAN is a group of computers and devices connected together in a relatively small area
(such as a house or an office). Your home network is considered a LAN.
MAC Address: MAC stands for Media Access Control. A MAC address is the hardware address of a device connected
to a network. The MAC address is a unique identifier for a device with an Ethernet interface. It is comprised of two
parts: 3 bytes of data that corresponds to the Manufacturer ID (unique for each manufacturer), plus 3 bytes that are often
used as the product’s serial number.
NAT: Network Address Translation. This process allows all of the computers on your home network to use one IP
address. Using the router’s NAT capability, you can access the Internet from any computer on your home network without
having to purchase more IP addresses from your ISP.
Port: Network Clients (LAN PCs) use port numbers to distinguish one network application/protocol over another. Below
is a list of common applications and protocol/port numbers:
Application Protocol Port Number
Telnet
FTP
TCP
TCP
TCP
TCP
TCP
UCP
23
21
SMTP
POP3
H.323
SNMP
25
110
1720
161
162
80
SNMP Trap UDP
HTTP
PPTP
TCP
TCP
1723
5631
5632
PC Anywhere TCP
PC Anywhere UDP
PPPoE: Point-to-Point Protocol over Ethernet. Point-to-Point Protocol is a secure data transmission method originally
created for dial-up connections; PPPoE is for Ethernet connections. PPPoE relies on two widely accepted standards,
Ethernet and the Point-to-Point Protocol. It is a communications protocol for transmitting information over Ethernet
between different manufacturers.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Protocol: A protocol is a set of rules for interaction agreed upon between multiple parties so that when they interface with
each other based on such a protocol, the interpretation of their behavior is well defined and can be made objectively,
without confusion or misunderstanding.
Router: A router is an intelligent network device that forwards packets between different networks based on network
layer address information such as IP addresses.
Subnet Mask: A subnet mask, which may be a part of the TCP/IP information provided by your ISP, is a set of four
numbers (e.g. 255.255.255.0) configured like an IP address. It is used to create IP address numbers used only within a
particular network (as opposed to valid IP address numbers recognized by the Internet, which must be assigned by
InterNIC).
TCP/IP, UDP: Transmission Control Protocol/Internet Protocol (TCP/IP) and Unreliable Datagram Protocol (UDP).
TCP/IP is the standard protocol for data transmission over the Internet. Both TCP and UDP are transport layer protocols.
TCP performs proper error detection and error recovery, and thus is reliable. UDP on the other hand is not reliable. They
both run on top of the IP (Internet Protocol), a network layer protocol.
WAN: Wide Area Network. A network that connects computers located in geographically separate areas (e.g. different
buildings, cities, countries). The Internet is a wide area network.
Web-based management Graphical User Interface (GUI): Many devices support a graphical user interface that is
based on the web browser. This means the user can use the familiar Netscape or Microsoft Internet Explorer to
control/configure or monitor the device being managed.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
|