Acer Altos G530 Series
User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
Notices
FCC notice
Class A devices do not have an FCC logo or FCC IDE on the label. Class B devices
have an FCC logo or FCC IDE on the label. Once the class of the device is
determined, refer to the following corresponding statement.
Class A equipment
This device has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to
correct the interference at personal expense.
Class B equipment
This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the device and receiver
Connect the device into an outlet on a circuit different from that to which
the receiver is connected
•
Consult the dealer or an experienced radio/television technician for help
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class A or Class B limits may be attached to this equipment.
Operation with noncertified peripherals is likely to result in interference to
radio and TV reception.
Caution! Changes or modifications not expressly approved by
the manufacturer could void the user’s authority, which is granted
by the Federal Communications Commission, to operate this
server.
Use conditions
This part complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Notice: Canadian users
This Class A/Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Laser compliance statement
The CD-ROM drive in this server is a laser product. The CD-ROM drive’s
classification label (shown below) is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO
BEAM.
Download from Www.Somanuals.com. All Manuals Search And Download.
v
Important safety instructions
Read these instructions carefully. Save these instructions for future reference.
1
2
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
3
4
Do not use this product near water.
Do not place this product on an unstable cart, stand, or table. The product
may fall, causing serious damage to the product.
5
Slots and openings on the back or bottom side of the chassis are provided
for ventilation; to ensure reliable operation of the product and to protect
it from overheating, these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surface. This product should never be placed near or
over a radiator or heat register, or in a built-in installation unless proper
ventilation is provided.
6
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
7
8
Do not allow anything to rest on the power cord. Do not locate this
product where persons will walk on the cord.
If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
9
Never push objects of any kind into this product through chassis slots as
they may touch dangerous voltage points or short out parts that could
result in a fire or electric shock. Never spill liquid of any kind on the
product.
10 Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage points or other risks. Refer all
servicing to qualified service personnel.
11 Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a
b
c
When the power cord or plug is damaged or frayed
If liquid has been spilled on the product
If the product has been exposed to rain or water
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
d
If the product does not operate normally when the operating
instructions are followed. Adjust only those controls that are covered
by the operating instructions since improper adjustment of other
controls may result in damage and will often require extensive work
by a qualified technician to restore the product to normal condition.
e
f
If the product has been dropped or the cabinet has been damaged
If the product exhibits a distinct change in performance, indicating a
need for service.
12 Replace the battery with the same type as the product's battery we
recommend. Use of another battery may present a risk of fire or explosion.
Refer battery replacement to a qualified service technician.
13 Warning! Batteries may explode if not handled properly. Do not
disassemble or dispose of them in fire. Keep them away from children and
dispose of used batteries promptly.
14 Use only the proper type of power supply cord set (provided in your
accessories box) for this unit. It should be a detachable type: UL listed/CSA
certified, type SPT-2, rated 7A 125V minimum, VDE approved or its
equivalent. Maximum length is 15 feet (4.6 meters).
Download from Www.Somanuals.com. All Manuals Search And Download.
Notices
FCC notice
1 System tour
Features summary
Front bezel
Front panel
Rear panel
System boards
19
Backplane board layout
2 System setup
Setting up the system
Server setup
35
35
36
37
37
38
38
39
40
40
52
Installation precautions
ESD precautions
Pre-installation instructions
Post-installation instructions
Opening the server
Removing the left-side panel
Opening the bezel door
Removing the front bezel
Removing the HDD cage bay cover
Configuring the four-bay HDD cage
Installing the four-bay HDD cage
Removing the four-bay HDD cage
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
60
Installing the HSF assembly
4 BIOS setup
BIOS setup
Entering BIOS setup
Main
Advanced
Boot
106
107
108
109
110
111
113
114
115
117
119
Boot Device Priority
Hard Disk Drives
Removable Drives
CD/DVD Drives
Security
Setting the Administrator/User password:
Server
System Management
Serial Console Features
Event Log Configuration
Exit
Download from Www.Somanuals.com. All Manuals Search And Download.
123
137
141
Resetting the system
First steps checklist
BIOS error messages
POST error messages
POST beep codes
ASM
System setup
RAID configuration
149
153
Setting up the system rack
Configuring the SATA RAID
169
169
169
170
Enabling the onboard SATA RAID function
Using the SATA RAID configuration utility
Creating a RAID 1 volume
Appendix D: SCSI RAID configuration
Configuring the SCSI/SCSI RAID HBA
Using the SCSI HBA setup utility
173
175
175
175
176
Using the SCSI RAID HBA setup utility
Using the MegaRAID configuration utility
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Index
179
Download from Www.Somanuals.com. All Manuals Search And Download.
The Acer Altos G530 server is a powerful dual-
processor system loaded with a host of new
and innovative features. The system offers a
new standard for flexible productivity ideal for
multimedia processing, intensive graphics
applications, general business applications,
email, web service, file clustering and print
services.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Features summary
Listed below are the system’s key features:
Processor
®
™
•
Single or Dual Intel Xeon processors with 1MB or 2MB L2 cache
and 800 MHz front system bus
®
•
•
Supports Intel Hyper-Threading Technology
®
Supports Intel EM64T (Extended Memory 64 technology)
Chipset
•
•
North bridge: Intel E7320 MCH (Memory Controller Hub)
South bridge: Intel 6300ESB ICH I/O controller
Memory
•
Supports up to four DIMM sockets for a maximum memory
capacity of 8 GB
•
Supports 512 MB, 1GB and 2GB DDR2-400 registered ECC memory
modules
•
•
•
Supports dual-channel memory bus
Supports memory sparing technology
Supports x4 SDDC (Single Device Data Correction)
Media storage
Three 5.25-inch device bays supports:
•
•
•
•
•
•
3.5-inch, 1.44 MB floppy drive
DVD-ROM, DVD-RW, DVD combo drive
DAT72 tape drive
AIT tape drive
LTO half-height tape drive
Download from Www.Somanuals.com. All Manuals Search And Download.
1 System tour
4
Optional media storage
•
•
Hot-plug HDD cage
•
•
Supports up to four 80-pin Ultra320 SCSI hard disk drives
Supports up to four SATA 150/300 hard disk drives
Easy-swap HDD cage
•
•
Supports up to four 68-pin SCSI hard disk drives
Supports up to four SATA 150/300 hard disk drives
Note: The main difference between a hot-plug HDD cage and an
easy-swap HDD cage is the presence of a backplane board on the
rear side of the hot-plug HDD cage.
SCSI controller
®
•
•
Onboard SCSI: LSI Logic 1020A Ultra320 SCSI controller
Dual channel SCSI, SCSI RAID host bus adapter (optional)
SATA controller
•
Onboard SATA: Intel 6300ESB ICH I/O controller supports dual
channel SATA 150 ports
•
Eight channel SATA RAID host bus adapter (optional)
RAID
•
•
Software RAID 0, 1 for onboard SATA ports
Software RAID 1 for onboard SCSI port
Networking
•
•
Intel 82541Pl Gigabit Ethernet controller
Marvell Yukon 88E8050 PCI Express Gigabit Ethernet controller
PCI I/O
Five PCI bus slots with three separate bus segments:
•
•
•
•
Two 32-bit/33 MHz PCI bus slots
Two 64-bit/66 MHz PCI-X bus slots
One x8 PCI Express bus slots (with x4 connectors)
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Graphic interface
®
•
ATI Rage XL chipset with 8MB SDRAM
I/O ports
•
Front panel
Two USB 2.0 ports
Rear panel
•
•
•
•
•
•
•
PS/2 keyboard and mouse port
Two USB 2.0 ports
VGA/monitor port
Serial port
Two LAN ports (RJ-45)
Operating system and software
®
®
•
•
•
Microsoft Windows Server 2003, X64 edition
Microsoft Windows Server 2003
Microsoft Windows 2000 Server (SP4)
®
®
•
•
•
Novell NetWare 6.5
Red Hat Enterprise Linux 3.0, EMT 64
Red Hat Enterprise Linux 3.0
™
•
•
SCO Openserver 5.0.7
®
SCO Unixware 7.1.4
®
•
•
•
•
SUSE Linux Enterprise Server 9.0
SUSE Linux Enterprise Server 9.0 X86_64
ASM (Acer Server Manager)
EasyBUILD (includes SATA/SCSI RAID Configuration Utility)
Power supply
•
•
600-watt single standard (non-redundant) power supply
610-watt (1+1) redundant power supply (optional)
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Front panel
No.
Icon
Component
Description
1
DVD/CD-ROM drive
Stop/Eject button
Press this button to open the CD
drive tray.
2
DVD/CD-ROM drive
activity indicator
When the LED indicator is lit, there
is activity in the CD drive.
3
4
5
DVD/CD-ROM drive
Volume control
Disk drive for reading CD-ROMs.
Adjusts the volume of the CD drive.
DVD/CD-ROM drive
Headphone/
Connects to microphones or
earphones.
Earphone port
6
7
5.25-inch drive bays
Power indicator 1
Two empty 5.25-inch drive bays
allow installation of additional
devices.
Indicates AC power is present or
system is turned on or off (green).
Download from Www.Somanuals.com. All Manuals Search And Download.
1 System tour
8
No.
Icon
Component
Description
8
Hard disk activity
indicator 2
Indicates the status of the system
hard drive.
9
LAN activity
indicator 3
Indicates an active link on the LAN1
port (green).
LAN activity
indicator 4
Indicates an active link on the LAN2
port (green).
10
Hot-plug HDD power
indicator 5
Indicates drive activity (green).
11
12
Four-bay hot-plug
HDD cage
Houses four hot-plug or easy swap
SCSI/SATA drives.
HDD cage bay
For additional storage options.
Supports a four-bay hot-plug HDD
cage.
13
14
USB ports
Connects to USB devices.
Power button
Press to turn on the system.
1, 2, 3, 4, 5 For more information about the status of the LED indicators, see
Front panel LED indicators table on page 9.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Front panel LED indicators
Below table lists the LED states on the front panel.
LED
Color
Status
On
Description
Power
Green
Power on
Blinking
Blinking
Off
System in ACPI sleep mode.
HDD activity
HDD
Green
Green
No HDD activity
Network is established.
LAN1 and 2
On
Blinking
•
•
Network activity.
Network is established and
running at its supported
speed.
Off
Network link is not established.
Hot-plug HDD LED indicators
Below table lists the possible disk drive status.
HDD Status
Green
Amber
Description
HDD access
Blinking
—
HDD activity
Download from Www.Somanuals.com. All Manuals Search And Download.
1 System tour
10
Rear panel
No.
Icon
Component
Description
1
Power supply
module bay
Allows installation of a redundant
and non-redundant redundant
power supply module. The hot-swap
redundant power supply module
may include three LEDs that will
indicate its operating status.
Note: If the system comes bundled
with only a single redundant power
supply module, you have the option
to separately purchase an extra
power supply module to provide the
system with redundant power
source.
2
3
USB ports
Connects to USB devices.
Connects to a PS/2 mouse.
PS/2 mouse port
Download from Www.Somanuals.com. All Manuals Search And Download.
11
No.
Icon
Component
Description
4
PS/2 keyboard
port
Connects to a PS/2 keyboard.
5
VGA/monitor
port
Connects to monitors.
6
7
Serial port
Connects to serial devices.
Connects to network cables.
Gigabit LAN
ports (10/100/
1000 Mbps)
8
9
Expansion slots
For installing expansion cards.
PCI slot lock
lever
Secures the PCI card to the system.
10
Rear system fan
Optimizes system airflow.
Download from Www.Somanuals.com. All Manuals Search And Download.
1 System tour
12
Rear panel LED indicators
Below table lists the LED states on the LAN port.
LED
Green
Yellow
Status
Link
On
—
•
•
Indicates 100MBps Ethernet
operation.
Network link is established.
Blinking
Off
—
—
Indicates transmission or reception
of data in the network.
•
Indicates 10 MBps Ethernet
operation.
•
•
Network link is not established.
The LAN cable is not working.
Activity
—
—
On
Indicates 1000 MBps Ethernet
operation.
Off
Network is idle.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Internal components
No.
Component
Power supply module (600 or 610-watts) 1
Rear system fan
1
2
3
4
5
Mainboard, CPU and heat sink fan assembly
PCI bus slot
Four-bay hot-plug HDD cage
1 The system supports a redundant or non-redundant power supply module. If the system
comes bundled with a single 610-w redundant power supply module, you have the option
to purchase an extra power supply module to provide the system with a redundant power
source.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
No.
1
Code
Description
USB_1~2
MS/KB
USB ports
2
Top: PS/2 mouse port
Bottom: PS/2 keyboard port
3
4
5
SERIAL A
VGA
Serial A port
VGA/monitor port
JA2 NIC_1
JA1 NIC_2
SYS_FAN_1
P/S AUX SIG
SYS_FAN_2
MAIN PWR
DIMM_1B - 1A
DIMM_2B - 2A
CPU PWR
CPU_1
Gigabit LAN 1 port (RJ-45)
Gigabit LAN 2 port (RJ-45)
System fan 1 connector
Auxillary power supply signal connector
System fan 2 connector
Power supply connector
DIMM 1B to 1A sockets
DIMM 2B to 2A sockets
CPU power supply connector
CPU 1 socket
6
7
8
9
10
11
12
13
14
15
16
17
CPU_2
CPU 2 socket
CPU_1 FAN
CPU_2 FAN
J17
CPU 1 fan connector
CPU 2 fan connector
Clear CMOS, Clear password and Recovery boot
jumper
18
19
20
PRIMARY IDE
FLOPPY
Primary IDE connector
FDD connector
LVD SCSI CH A
SCSI channel connector
Download from Www.Somanuals.com. All Manuals Search And Download.
1 System tour
16
No.
Code
Description
21
22
23
24
SATA_A1- A2
HSBP_B
J38
SATA connectors
Hot-plug backplane connector
Front panel LED connector
I2C
I2C connector (reserved for ARMC/2)
CMOS Battery
25
26
27
28
29
30
31
32
BATTERY
USB3~4
J19
USB 3 and 4 connector
Chassis intrusion connector
Serial B connector
SERIAL B
J26
SCSI LED connector
SLOT_1 and 2
SLOT_3 and 5
SLOT_4
PCI-X slots (64-bit/66 MHz)
PCI slots (32-bit/33 MHz)
x8 PCI-Express slot (with x4 throughput)
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Jumper settings
J17 jumper
The J17 jumper provides a total of 3-pin blocks that are used to
configure several system recovery and update options.
The table below lists each jumper option
Pin no.
Pin function
Description
1-2
2-3
Normal boot (default)
Force erase
Clear CMOS settings
5-6
6-7
Protect (default)
Erase
Clear password settings
Recovery boot settings
9-10
Normal boot (default)
Recovery boot
10-11
J38 jumper
The J38 jumper is a standard SSI 34-pin header that supports the system
front panel.
Download from Www.Somanuals.com. All Manuals Search And Download.
1 System tour
18
The following below lists the pin-out of the J38 header.
Pin no.
Signal name
ACPI LED gm
Key
Pin no.
Signal name
1
3
2
4
SB5V
Fan fault LED*
(no support)
5
ACPI LED amber
6
Fan fault LED*
(no support)
7
HDD LED
8
System fault LED*
System fault LED*
LAN 1 Activity LED
LAN 1 Activity LED#
SMB SDA
9
NMI button
10
12
14
16
18
20
22
24
26
28
30
32
34
11
13
15
17
19
21
23
25
27
29
31
33
ACPI switch
ACPI switch (GND)
Reset switch
Reset switch (GND)
SMB SCL
Sleep switch* (no support)
Intruder*
Sleep switch (GND)
LAN 2 Activity LED
LAN 2 Activity LED#
Key
NMI switch#
Key
NC
NC
NC
NC
NC
NC
NC
NC
* and NC = No connection
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Backplane board layout
The backplane board attached to the four-bay hot-plug HDD cage
provides a convenient interface between the SCSI or SATA drives and
the mainboard.
SCSI backplane board layout
Rear
Front
No.
1
Code
Description
SCSI HDD connectors
2
W83792D_ID1
792D_ID1 ADDR select jumper
Jumper setting:
Short 1-2 — 5EH (default)
Short 2-3 — 5AH
3
4
5
3-pin fan connector
4-pin power cable connector
68-pin SCSI data cable connector
Download from Www.Somanuals.com. All Manuals Search And Download.
1 System tour
20
No.
Code
Description
6
7
J3
LED indicator jumper
Jumper setting:
Short 1-2 — Link LED on
Short 2-3 — Link LED dark
SAF-TE ID
SAF-TE ID jumper
Jumper setting:
Short 1-2 — ID8 (default)
Short 2-3 — ID6
Download from Www.Somanuals.com. All Manuals Search And Download.
21
SATA backplane board layout
Rear
Front
No.
1
Code
Description
SATA HDD connectors
2
SAF-TE heartbeat LED and
Manufacturing function jumper
Debug connector
3
4
JP2
J1
Backplane no. jumper
Jumper setting:
Short 1-2 — 1st BPB (backplane board)
Short 2-3 — 2nd BPB
5
6
JP1
ICMB (Intelligent Chassis Management Bus)
connector
FAN1 and
FAN2
Fan connectors
Download from Www.Somanuals.com. All Manuals Search And Download.
1 System tour
22
No.
Code
Description
7
8
792D_ID1
792D_ID1 ADDR select jumper
Jumper setting:
Short 1-2 — 5EH (default)
Short 2-3 — 5AH
J3
IPMB (Intelligent Platform Management Bus)
connector (reserved for SATA RAID card)
9
CN1 and CN2
4-pin power cable connector
SATA data cable connectors
10
SATA_CON0 to
SATA CON3
11
12
J4
J5
Cascade connector
I2C bus interface connector
Download from Www.Somanuals.com. All Manuals Search And Download.
This chapter gives you instructions on how to set up
the system. Procedures on how to connect
peripherals are also explained.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Setting up the system
Pre-installation requirements
Selecting a site
Before unpacking and installing the system, select a suitable site for
the system for maximum efficiency. Consider the following factors
when choosing a site for the system:
•
•
•
•
•
Near a grounded power outlet
Clean and dust-free
Stable surface free from vibration
Well-ventilated and away from sources of heat
Secluded from electromagnetic fields produced by electrical
devices such as air conditioners, radio and TV transmitters, etc.
Checking the package contents
Check the following items from the package:
•
•
•
•
Acer Altos G530 system
Acer EasyBUILDTM
Acer Altos G530 accessory box
System keys
If any of the above items are damaged or missing, contact your dealer
immediately.
Save the boxes and packing materials for future use.
Download from Www.Somanuals.com. All Manuals Search And Download.
2 System setup
26
Connecting peripherals
Refer to the illustration below for specific connection instructions on
the peripherals you want to connect to the system.
Note: Consult the operating system manual for information on
how to configure the network setup.
Download from Www.Somanuals.com. All Manuals Search And Download.
2 System setup
28
The system starts up and displays a welcome message on the
monitor. After that, a series of power-on self-test (POST) messages
appears. The POST messages indicate if the system is running well
or not.
Note: If the system does not turn on or boot after pressing the
power button, go to the next section for the possible causes of the
boot failure.
Aside from the POST messages, you can determine if the system is in
good condition by checking if the following occurred:
•
•
Power indicator on the front panel lights up (green)
Num Lock, Caps Lock, and Scroll Lock indicators on the keyboard
light up
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Power-on problems
If the system does not boot after you have applied power, check the
following factors that might have caused the boot failure.
•
The external power cable may be loosely connected.
Check the power cable connection from the power source to the
power cable socket on the rear panel. Make sure that the cable is
properly connected to the power source and to the power cable
socket.
•
•
No power comes from the grounded power outlet.
Have an electrician check your power outlet.
Loose or improperly connected internal power cables.
Check the internal cable connections. If you are not confident to
perform this step, ask a qualified technician to assist you.
Warning! Make sure all power cords are disconnected from
the electrical outlet before performing this task.
Note: If you have gone through the preceding actions and the
system still fails to boot, ask your dealer or a qualified technician
for assistance.
Download from Www.Somanuals.com. All Manuals Search And Download.
2 System setup
30
Configuring the system OS
The Altos G530 comes with Acer EasyBUILDTM that allows you to
conveniently install your choice of operating system. To start using
EasyBUILD, follow the steps below.
1
2
Locate the EasyBUILD System CD included in the system package.
With the system turned on, gently press the CD-ROM drive Stop/
Eject button.
3
4
When the disc tray slides open, insert the EasyBUILD System CD
with the label or title side of the disc facing upward.
Note: When handling the disc, hold it by the edges to avoid
smudges or fingerprints.
Gently press the disc down to make sure that it is properly
inserted.
Caution! While pressing the disc, be careful not to bend the disc
tray. Make sure that the disc is properly inserted before closing
the disc tray. Improper insertion may damage both the disc and
the CD-ROM drive.
5
6
Gently press the drive Stop/Eject button again to close the disc
tray.
The Acer EasyBUILD sequence begins. Follow all onscreen
instructions.
For more information, refer to the EasyBUILD Installation guide.
Note: EasyBUILD System CD supports Windows 2000, Windows
Server 2003 and Red Hat Linux operating system only.
Windows or Linux OS CD is needed when you install the OS with
the EasyBUILD System CD.
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Server setup
Aside from its tower configuration, the Altos G530 server system can
also be mounted in a rack-model position. A rack mount kit is available
model design. To purchase a rack mount kit, contact your local Acer
The figure below shows the Altos G530 server in a rack-mount position.
For instructions on tower-to-rack configuration, refer to “Appendix B:
Acer Altos G530 rack installation guide” on page 151.
Download from Www.Somanuals.com. All Manuals Search And Download.
2 System setup
32
Turning off the system
There are two ways by which you can turn off the server. These include:
To turn off the server, on the Windows taskbar click on the Start
button, point to Shut Down..., select Shut down from the
drop-down window then click on OK. You can then turn off all
peripherals connected to your server.
If you cannot shut down the server, press the power button for at least
four seconds. Quickly pressing the button may put the server in a
Suspend mode only.
Download from Www.Somanuals.com. All Manuals Search And Download.
This chapter discusses the precautionary
measures and installation procedures you
need to know when upgrading the system.
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Installation precautions
Before you install any server component, we recommend that you read
the following sections. These sections contain important ESD
precautions along with pre-installation and post-installation
instructions.
ESD precautions
Electrostatic discharge (ESD) can damage the processor, disk drives,
expansion boards, motherboard, memory modules and other server
components. Always observe the following precautions before you
install a server component:
1
Do not remove a component from its protective packaging until
you are ready to install it.
2
Wear a wrist grounding strap and attach it to a metal part of the
server before handling components. If a wrist strap is not
available, maintain contact with the server throughout any
procedure requiring ESD protection.
Pre-installation instructions
Perform the steps below before you open the server or before your
remove or replace any component:
1
2
3
4
5
Turn off the system and all the peripherals connected to it.
Unplug all cables from the power outlets.
Place the system unit on a flat, stable surface.
Open the system according to the instructions on page 37.
Follow the ESD precautions described in this section when
handling a server component.
6
Remove any expansion board(s) or peripheral(s) that block access
to the DIMM slots or other component connector.
See the following sections for specific installation instructions on the
component you want to install.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
36
Warning! Failure to properly turn off the server before you
start installing components may cause serious damage. Do
not attempt the procedures described in the following
sections unless you are a qualified service technician.
Post-installation instructions
Perform the steps below after installing a server component:
1
See to it that all components are installed according to the
described step-by-step instructions.
2
Reinstall any expansion board(s) or peripheral(s) that you have
previously removed.
3
4
5
Reinstall the chassis panels.
Connect the necessary cables.
Turn on the system.
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Opening the server
Caution! Before you proceed, make sure that you have turned
installation instructions” on page 35.
You need to open the server before you can install additional
components. The front bezel and left-side panel are removable to
allow access to the system’s internal components. Refer to the
following sections for instructions.
Removing the left-side panel
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
2
Remove the left-side panel.
(1) Remove the two screws located on the rear edge of the left-
side panel (1).
(2) Press the left-side panel release button (2).
(3) Slide the left-side panel toward the rear of the chassis (3).
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
38
Opening the bezel door
A security lock secures the bezel door to protect the system unit from
unauthorized access.
To open the bezel door:
1
Insert the key into the lock and turn it clockwise until it points to
the unlock icon
.
2
Pull open the bezel door.
Removing the front bezel
1
2
3
Remove the left-side panel. See page 37.
Slightly bend the plastic retention tabs to release the latches (1).
Gently detach the bezel from the chassis (2).
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
40
Configuring the four-bay HDD cage
This section explains how to install a four-bay hot-plug HDD cage as
well as procedures on how to install a hard disk into the cage’s hard
disk carrier.
Installing the four-bay HDD cage
The Altos G530 has two HDD cage bays that accept the following HDD
cages:
•
•
•
•
Hot-plug SCSI HDD cage
Easy-swap SCSI HDD cage
Hot-plug SATA HDD cage
Easy-swap SATA HDD cage
The main difference between a hot-plug HDD cage and an easy-swap
HDD cage is the presence of a backplane board on the rear side of the
hot-plug HDD cage.
The system ships out with only a single four-bay SCSI or SATA HDD cage
leaving one bay empty. You have the option to purchase an extra cage
to provide the system with additional storage capacity and scalability.
Contact your local Acer representative for more information.
cage in the system, you can use either the onboard SCSI channel
(LVD SCSI CH A) or SATA (SATA_A1 or A2) connectors, or you can
install a SCSI/SATA RAID card. The SCSI/SATA RAID card should be
Acer-qualified, compatible with the system and include
appropriate drivers. Refer to page 70 for intructions on how to
Refer to the “Mainboard layout” on page 14 for the location of
the SCSI channel or SATA connectors.
To purchase a SCSI or SATA RAID card, contact your local Acer
Download from Www.Somanuals.com. All Manuals Search And Download.
41
To install the hot-plug SCSI HDD cage:
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
2
3
Remove the HDD cage bay cover. See page 39.
Remove the screw that secures the cover to the empty HDD bay
(1), then detach the cover (2).
4
Install the hot-plug cage.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
42
(1) Slide the cage into the chassis with the backplane board
facing the rear of the chassis. The cage is locked to the chassis
with an audible click.
(2) Locate and attach the following cables clamped on the side of
the chassis to their corresponding connectors on the
backplane board:
Important: If a four-bay hot-plug SCSI HDD cage is already
installed in the top HDD bay, you must block the W83792D_ID1
jumper. Set pins 2 and 3 to short.
(1) SCSI data cable
Download from Www.Somanuals.com. All Manuals Search And Download.
43
(2) SCSI HDD power cables
5
6
Observe the post-installation instructions described on page 36.
Important: When you are detaching the hot-plug HDD cage
from the chassis, make sure to first remove all hard disks from
their carriers. For instructions, see “Installing an additional hard
disk into the HDD cage carrier” on page 53.
Change the RAID configuration of your hard disk. For details on
how to change the RAID configuration of your hard disk, go to
“Appendix D: SCSI RAID configuration” on page 173.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
44
To install the easy-swap SCSI HDD cage:
The easy-swap SCSI HDD cage is an optional four-bay internal HDD
enclosure without a SCSI backplane board.
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
2
3
Remove the HDD cage bay cover. See page 39.
Remove the screw that secures the cover to the empty HDD bay,
then detach the cover.
4
Install the easy-swap cage.
(1) Slide the cage into the chassis. The cage is locked to the chassis
with an audible click.
(2) Locate and attach the following cables to their corresponding
connectors on the SCSI hard drive and SCSI RAID card. For
instructions on how to install a SCSI RAID card see page 70.
(1) SCSI data cable
Download from Www.Somanuals.com. All Manuals Search And Download.
45
(2) SCSI HDD power cables
5
6
Observe the post-installation instructions described on page 36.
Important: When you are detaching the easy-swap cage from
the chassis, make sure to first remove all cables attached to the
hard disks.
Change the RAID configuration of your hard disk. For details on
how to change the RAID configuration of your hard disk, go to
“Appendix D: SCSI RAID configuration” on page 173.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
46
To install the hot-plug SATA HDD cage:
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
2
3
Remove the HDD cage bay cover. See page 39.
Remove the screw that secure the cover of the empty HDD bay,
then detach the cover.
Download from Www.Somanuals.com. All Manuals Search And Download.
47
4
Install the hot-plug cage.
(1) Slide the cage into the chassis. The cage is locked to the chassis
with an audible click.
5
Connect the following cables to their corresponding connectors on
the SATA RAID backplane board, mainboard and adapter:
Important: If a four-bay hot-plug SATA HDD cage is already
installed in the top HDD bay, you must block the J1 jumper. Set
pins 2 and 3 to short.
(1) Attach the SATA data cable to the SATA HDD connector on the
backplane board (1), then connect the other end of the cable
to the SATA connector on the SATA RAID card.
Note: SATA connectors on the controller are keyed. Make sure
the SATA data cables are properly connected to its corresponding
connectors on the SATA RAID card.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
48
(2) Attach the system’s power cable to the SATA power cable
connector on the backplane board (2).
Note: The SATA RAID data cables must be installed and removed
in the following order: SATA0, SATA1, SATA2, then SATA3.
6
7
Observe the post-installation instructions described on page 36.
Important: When you are removing the hot-plug cage from the
chassis, make sure to first remove all hard disks from their carriers.
For instructions, see “Installing an additional hard disk into the
HDD cage carrier” on page 53.
Change the RAID configuration of your hard disk. For details on
how to change the RAID configuration of your hard disk, go to
“Appendix C: SATA RAID configuration” on page 167.
Download from Www.Somanuals.com. All Manuals Search And Download.
49
To install the easy-swap SATA HDD cage:
The easy-swap SATA HDD cage is an optional four-bay internal HDD
enclosure without a SATA backplane board.
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
2
3
Remove the HDD cage bay cover. See page 39.
Remove the screw that secures the cover to the empty HDD bay,
then detach the cover.
4
Install the easy-swap cage.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
50
(1) Slide the cage into the chassis. The cage is locked to the chassis
with an audible click.
(2) Locate and attach the power (1) and SATA (2) cables to their
corresponding connectors on the hard drives and SATA RAID
card.
5
Observe the post-installation instructions described on page 36.
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Important: When you are removing the easy-swap cage from
the chassis, make sure to first remove all cables attached to the
hard disks.
6
Change the RAID configuration of your hard disk. For details on
how to change the RAID configuration of your hard disk, go to
“Appendix C: SATA RAID configuration” on page 167.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
52
Removing the four-bay HDD cage
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
2
3
Disconnect the data and power cables from the backplane board.
Move the release slider all the way up to eject the hot-plug or easy
swap HDD cage (1).
4
Remove the cage from the HDD bay (2).
5
Observe the post-installation instructions described on page 36.
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Installing an additional hard disk into the HDD
cage carrier
Important: You need not remove the four-bay hot-plug HDD
cage from the chassis to install a hard disk into its carrier.
1
Carefully pull out the hard disk carrier cover (1).
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
54
2
Install a hard disk on the hard disk carrier (1), then secure it with
the four screws that came with the hard disk carrier (2).
3
4
Insert the new hard disk carrier into the cage with the lever still
extended (1).
Make sure that the drive is properly inserted before closing the
lever, then push the lever back until it clicks into place (2). .
Download from Www.Somanuals.com. All Manuals Search And Download.
55
Replacing the CD-ROM drive
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
2
3
Disconnect the power and IDE cables from the old drive.
Push the lever in the direction of the unlock icon
(1), then pull
the drive out of the chassis (2).
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
56
4
Install a new 5.25-inch drive into the drive bay (1), then push the
lever in the direction of the lock icon
(2).
5
6
Connect the power and IDE cables to the new drive.
Observe the post-installation instructions described on page 36.
Download from Www.Somanuals.com. All Manuals Search And Download.
57
Installing 5.25-inch drives
The two empty 5.25-inch drive bays allow you to install additional
drives such as another backup hard drive, CD-ROM drive, or a tape
drive. These options provide the system with additional storage
capacity.
To install a 5.25-inch tape drive:
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
2
Remove the two screws that secure the cover to the empty
5.25-inch drive bay (1), then detach the cover (2).
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
58
3
Install a tape drive into the drive bay (1), then push the lever in
the direction of the lock icon
(2).
4
5
Connect the power and IDE cables to the tape drive.
Observe the post-installation instructions described on page 36.
Download from Www.Somanuals.com. All Manuals Search And Download.
59
Upgrading the processor
This section includes instructions for installing and removing a
processor and heat sink fan (HSF) assembly.
Installing the CPU
The mainboard has two 604-pin processor socket that support Intel
Xeon processors. The system ships out with only a single Intel Xeon
processor installed leaving one CPU socket empty. You have the option
to purchase an extra CPU for the system.
Important: When installing an additional CPU, make sure the
CPU has the same stepping and running values at the same
frequency specifications as the default CPU.
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
2
3
4
5
Locate an empty CPU socket on the mainboard.
Pull the CPU socket retainer lever to a fully open, upright position.
Remove the CPU from its protective packaging.
Align the CPU with the socket, making sure that pin 1 (indicated
by the notched corner) of the CPU connects to hole 1 of the socket
(on the bottom right corner), then insert the CPU into the socket
(1).
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
60
6
Press the retainer lever down to lock the CPU in place (2).
Installing the HSF assembly
1
Apply thermal grease.
Apply approximately 0.1ml of the thermal grease compound on it’s
top side.
2
Install the heat sink fan assembly
Download from Www.Somanuals.com. All Manuals Search And Download.
61
(1) Align the heat sink fan assembly to the CPU (1).
(2) Using a screwdriver, tighten the heatsink’s four screws to
secure it to the mainboard (2).
(3) Connect the CPU fan cable to its mainboard connector. Refer
to “Mainboard layout” on page 14 for the location of the CPU
fan connector.
3
Observe the post-installation instructions described on page 36.
Removing the HSF assembly
Important: Before removing a CPU from the mainboard, make
sure to create a backup file of all important data.
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
Warning! The heat sink becomes very hot when the system
is on. NEVER touch the heat sink with any metal or with
your hands.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
62
2
3
Disconnect the CPU fan cable from its mainboard connector.
Loosen the four screws that hold the HSF assembly to the
mainboard (1).
4
Pull the HSF assembly away from the CPU (2).
5
Place the HSF assembly upside down on a flat surface.
Note: Wipe off the thermal grease from both the HSF assembly
and CPU using an alcohol pad.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
64
Upgrading the system memory
This section includes instructions for removing and installing a memory
module.
Altos G530 has four DDR2-400 DIMM slots. Each slot supports 512 MB,
1GB or 2GB memory modules. The maximum memory capacity is 8GB.
Memory module installation guidelines
•
The minimum memory configuration is one DIMM, installed in the
DIMM 1B socket (the socket farthest from the CPU sockets).
However, for optimum performance and dual-channel interleave
operation, a minimum of two DIMMs should be installed. DIMMs
on channel A (DIMM 1A and 2A) are paired with DIMMs on
channel B (DIMM 1B and 2B) to enable 2-way interleaving.
Note: Dual-channel memory requires symmetrical memory
modules using the same density (e.g. 512 MB), bus width (e.g. x8,
x16) and granule technology (e.g. 512M-bit).
•
Populate both DIMMs in bank 1 (DIMM 1B and 1A) first, before
populating DIMMs in bank 2 (DIMM 2B and 2A). Bank 2 must be
populated in pairs.
Note: Refer to the “Mainboard layout” on page 14 for the
location of the DIMM slots.
Download from Www.Somanuals.com. All Manuals Search And Download.
65
Both DIMMs in a bank must be identical (same manufacturer, CAS
•
latency, number of rows, columns and devices, timing parameters,
etc.). Although DIMMs within a bank must be identical, the BIOS
supports various DIMM sizes and configurations allowing the
banks of memory to be different.
Warning! For the system to function, DIMM modules must
be installed or removed in matched pairs, following the
socket sequence : DIMM 1B and 1A first, then DIMM 2B and
2A. DIMM modules of the same type, banking, stacking
technology, and manufacturer must be installed in the
Altos G530 system.
Note: Refer to “Mainboard layout” on page 14 for the location
of the DIMM sockets for each processor.
The table below lists the supported memory installation based on the
memory interleave configuration:
Bank 1
DIMM 1A
Bank 2
DIMM 2A
Memory Interleave
DIMM 1B
512 MB
1 GB
DIMM 2B
1-way
1-way
1-way
2-way
2-way
2-way
2-way
2-way
2-way
2 GB
512 MB
1 GB
512 MB
1 GB
2 GB
2 GB
512 MB
1 GB
512 MB
1 GB
512 MB
1 GB
512 MB
1 GB
2 GB
2 GB
2 GB
2 GB
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
66
Altos G530 supports memory sparing function. To provide a more fault
over to a spare DIMM device in the event that a primary DIMM in use
exceeds a specified threshold of runtime errors. One of the DIMMs
installed per channel will not be used, but kept in reserve. In the event
of significant failures in a particular DIMM, it and its corresponding
partner in the other channel (if applicable), will, over time, have its
data copied over to the spare DIMM held in reserve. When all the data
has been copied, the reserved DIMM will be put into service and the
failed DIMM will be removed from service. Only one sparing cycle is
supported. If the memory sparing feature is not enabled, then all
DIMMs will be visible in normal address space.
Refer to “Memory Configuration” on page 101 for more information
about configuring the memory spare parameter in the BIOS Setup
Utility.
Download from Www.Somanuals.com. All Manuals Search And Download.
67
Removing a DIMM
Before you can install a new DIMM in a socket, remove first any
previously installed DIMM from that socket.
Important: Before removing any DIMM from the mainboard,
make sure to create a backup file of all important data.
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
2
3
Locate the DIMM sockets on the mainboard.
Press the holding clips on both sides of the socket outward to
release the DIMM.
4
Gently pull the DIMM upward to remove it from the socket .
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
68
Installing a DIMM
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
2
Locate the DIMM sockets on the mainboard.
Note: DIMM modules must be installed in matched pairs,
following the socket sequence: DIMM 1B and 1A first, then DIMM
2B and 2A.
3
4
5
Open the clips on the socket.
Align then insert the DIMM into the socket.
Press the holding clips inward to lock the DIMM in place.
Note: The DIMM socket is slotted to ensure proper installation.
If you insert a DIMM but it does not fit easily into the socket, you
may have inserted it incorrectly. Reverse the orientation of the
DIMM and insert it again.
6
Observe the post-installation instructions described on page 36.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
70
This section explains how to install an expansion card. The onboard
expansion slots supports PCI (Peripheral Component Interconnect),
PCI-X, and PCI Express cards. PCI Express slot is a new type of interface
and differs in length than the conventional PCI/PCI-X slots. You should
always install the correct type of plug-in expansion cards in the x4 PCI
Express slot. Contact your dealer for qualified PCI Express card vendors.
To install an expansion card:
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
2
Locate an empty expansion slot on the mainboard.
To purchase a SCSI RAID card, contact your local Acer
3
4
5
6
7
Press the slot release latch outward (1).
Pull out the slot cover (2). Store it for reassembly later.
Remove the expansion card from its protective packaging.
Align the card in the empty slot.
Insert the card into the selected slot (3). Make sure that the card is
properly seated.
Download from Www.Somanuals.com. All Manuals Search And Download.
71
Press the PCI slot release latch on the rear panel of the server (4).
8
9
Observe the post-installation instructions described on page 36.
Note: When you turn on the system, the BIOS setup automatically
detects and assigns resources to the new device (applicable only to
plug-and-play expansion cards).
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
72
Upgrading the power supply
The Altos G530 system may ship out with a redundant or non-
redundant power supply module.
Installing a redundant power supply module
The Altos G530 power subsystem consists of two redundant power
supply module bays that accept 610-watt hot-swap redundant power
supply modules. The system ships out with only a single power supply
module leaving one power supply module bay empty. You have the
option to purchase an extra power supply module to provide the
system with a redundant power source. A redundant power
configuration enables a fully-configured system to continue running
even if one power supply module fails.
WARNING! To reduce the risk of personal injury or
damage to the equipment, the installation of power
supply modules should be referred to individuals who are
qualified to service server systems and are trained to deal
with equipment capable of generating hazardous energy
levels.
WARNING! To reduce the risk of personal injury from
hot surfaces, observe the thermal labels on each power
supply module. You can also consider wearing protective
gloves.
WARNING! To reduce the risk of personal injury from
electric shock hazards, do not open the power supply
modules. There are no serviceable parts inside the
module.
Caution! Electrostatic discharge can damage electronic
components. Make sure that you are properly grounded
before handling a power supply module.
Download from Www.Somanuals.com. All Manuals Search And Download.
73
1
Remove the cover of the empty power supply module bay.
Note: If the system ships out with a screw on the cover, remove
the screw first then detach the cover.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
74
2
Hold the handle on front of the power supply module while
pressing your thumb on the release latch. Slide the power supply
module into the empty bay until you feel resistance.
3
4
Press the module handle to secure the power supply module to its
bay.
Verify that the power indicators on the main power supply and on
the newly installed redundant power supply are illuminated
green.
Download from Www.Somanuals.com. All Manuals Search And Download.
75
Installing a non-redundant power supply module
The Altos G530 power subsystem accepts a 600-watt non-redundant
power supply module. If you are replacing a previously installed power
supply module, turn it off and unplug it.
1
Observe the ESD precautions and pre-installation instructions
described on page 35.
2
3
Detach the power and power supply cable from their connectors.
Remove the four screws on the cover of the power supply module
bay, then detach the cover.
4
Slide the power supply module toward the front of the system,
then lift the power supply module out of the chassis.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System upgrade
76
5
Slide the new power supply module into the bay, then secure it to
the chassis with the four screws removed earlier.
6
7
Attach the power cable to the power cable socket.
Attach the power supply cable to the mainboard connector.
Note: If a four-bay hot-plug HDD cage is already installed in your
chassis, attach the power cable to the hard drive’s power cable
connector.
8
Observe the post-installation instructions described on page 36.
Download from Www.Somanuals.com. All Manuals Search And Download.
This chapter gives information about the
system BIOS and discusses how to configure
the system by changing the settings of the
BIOS parameters.
Download from Www.Somanuals.com. All Manuals Search And Download.
79
BIOS setup
BIOS setup is a hardware configuration program built into the system's
Basic Input/Output System (BIOS). Since most systems are already
properly configured and optimized, there is no need to run this utility.
You will need to run this utility under the following conditions:
•
•
When changing the system configuration
When a configuration error is detected by the system and you are
prompted ("Run Setup" message) to make changes to the BIOS
setup
Note: If you repeatedly receive Run Setup messages, the battery
may be bad. In this case, the system cannot retain configuration
values in CMOS. Ask a qualified technician for assistance.
•
•
•
When redefining the communication ports to prevent any conflicts
When making changes to the Power Management configuration
When changing the password or making other changes to the
security setup
BIOS setup loads the configuration values in a battery-backed
nonvolatile memory called CMOS RAM. This memory area is not part of
the system RAM which allows configuration data to be retained when
power is turned off.
Before you run BIOS setup, make sure that you have saved all open
files. The system reboots immediately after you close the setup.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
80
Entering BIOS setup
Power on the server to start the system POST process. During bootup,
press F2 to enter the BIOS setup screen.
Note: You must press F2 while the system is booting. This key
does not work during any other time.
There are several tabs on the setup screen corresponding to the six
major BIOS menus:
•
•
•
•
•
•
Main
Advanced
Boot
Security
Server
Exit
The parameters on the screens shown in this User’s Guide display
default system values. These values may not be the same as those in
the system.
Note the following reminders when moving around the setup screen:
•
Use the Left and Right arrow keys to move to the next page or to
return to the previous screen.
•
•
Use the Up and Down arrow keys to select an item.
Use the + and - keys to select an option.
Note: You can configure a parameter that is enclosed in square
brackets. Grayed-out items have fixed settings and are not
user-configurable.
•
•
Use the Tab key to select a field.
Use the Enter key to display a submenu screen.
Note: When a parameter is preceeded by a >, it means that a
submenu screen is available.
Download from Www.Somanuals.com. All Manuals Search And Download.
81
•
•
•
Press F1 for General Help on using the BIOS setup.
Press F10 to save changes and close the BIOS setup.
Press Esc to close the BIOS setup.
In the descriptive table following each of the screen illustrations,
settings in boldface are the default and suggested parameter settings.
Note: The BIOS screens shown in the following pages may vary
depending on the system configuration.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
82
Main
The Main menu displays basic and important information about the
system. These information are necessary for troubleshooting and may
be required when asking for technical support. These entries are for
your reference only and are not user-configurable.
The last two parameters on the screen lets you define the sytem’s time
and date settings. The real-time clock keeps the system date and time.
After setting the date and time, you do not need to enter them every
time you turn on the system. As long as the internal battery remains
good and connected, the clock continues to keep the date and time
accurately even when the power is off.
Parameter
Description
AMIBIOS Version
Build Date
Version of the BIOS setup utility.
Date when the BIOS setup was created.
Type of processor currently installed in the server.
Processor Type
Download from Www.Somanuals.com. All Manuals Search And Download.
83
Parameter
Description
Processor Speed
The processor speed is the speed at which a
microprocessor executes instructions. Clock speeds
are expressed in megahertz (MHz), with 1 MHz
being equal to 1 million cycles per second. The
faster the clock, the more instructions the CPU can
execute per second.
Processor Count
Indicates the number of processors currently
installed in the server.
System Memory Size
Indicates the total amount of onboard memory. The
memory size is automatically detected by BIOS
during the POST. If you install additional memory,
the system automatically adjusts this parameter to
display the new memory size.
Server Board MCH
Stepping
Indicates the stepping revision of the memory
controller
System Time
Sets the time following the hour-minute-second
format. Valid values for hour, minute, and second
are:
Hour: 00 to 23
Minute: 00 to 59
Second: 00 to 59
System Date
Sets the date following the weekday-month-day-
year format. Valid values for weekday, month, day,
and year are:
Weekday: Sun, Mon, Tue, Wed, Thu, Fri, Sat
Month: Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep,
Oct, Nov, Dec
Day: 1 to 31
Year: 1980 to 2079
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
84
Advanced
The Advanced menu contains parameter values that define how the
system behaves on startup.
Warning! Be cautious in setting parameter values in the
Advanced menu as any incorrect value may cause the
system to malfunction.
Press Enter to enter the submenu screen of the parameters shown in
the screen below.
Download from Www.Somanuals.com. All Manuals Search And Download.
85
Processor Configuration
The Processor Configuration submenu displays CPU settings such as
type, actual speed, cache size and other CPU related settings.
Parameter
Manufacturer
Brand String
Frequency
Description
Option
Processor manufacturer
Processor brand identification number
Indicates the calculated processor
speed.
FSB Speed
Indicates the processor front side bus
speed.
CPU 1 CPUID
ID number of CPU 1.
CPU 1 Cache L1
CPU 1 Cache L2
Indicates CPU 1 cache L1 size.
Indicates CPU1 cache L2 size.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
86
Parameter
Description
Option
CPU 2 CPUID
ID number of the CPU 2.
Indicates CPU 2 cache L1 size.
Indicates CPU 2 cache L2 size.
CPU 2 Cache L1
CPU 2 Cache L2
Max CPUID Value
Limit
Enable to boot legacy operating
systems.
Disabled
Ensabled
Execute Disable
Bit
When Enabled, the processor disables
code execution when a worm
attempts to insert a code in the buffer,
preventing damage and worm propa-
gation.
Disabled
Ensabled
When Disabled, the processor forces
the Execute Disable Bit feature flag to
always return to 0.
Note: This feature is hidden if the
procesor does not support this
function.
C1E Support
When Enabled, the CPU power
consumption will be lower when the
system is idle.
Disabled
Ensabled
Note: This feature is hidden if the
procesor does not support this
function.
Hardware
Prefetcher
Enables or disables the processor
Hardware Prefetch feature.
Disabled
Ensabled
Adjacent Cache
Line Prefetch
Enables or disables the processor
Adjacent Cache Line Prefetch feature.
Disabled
Ensabled
Hyper-Threading
Technology
Enables or disables the
Hyper-Threading function of the
processor.
Enabled
Disabled
The Hyper-Threading Technology
controls Hyper-Threading state.
Primarily used to support older OS
that do not support Hyper Threading.
Download from Www.Somanuals.com. All Manuals Search And Download.
87
Parameter
Description
Option
HT Technology in
MPS
When Enabled, adds secondary
processor threads to the MPS
Disabled
Enabled
(multiprocessor) table for the pre-ACPI
(pre- Advanced Configuration and
Power Interface) operating systems.
®
When set to Auto, this feature allows
the operating system to reduce power
consumption.
Disabled
Intel SpeedStep
Technology
Auto
When set to Disabled, the system
operates at maximum CPU speed.
Note: This parameter will be hidden
when the processor does not support
this function.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
88
IDE Configuration
The IDE Configuration submenu lets you define the parameter settings
related to the hard disk/s.
Parameter
Description
Option
Onboard P-ATA
Channels
When set to Both, the system can
support both Primary and Secondary
PATA Controllers.
Both
Disabled
Primary
Secondary
When set to Disabled, it disables the
integrated PATA Controller.
When set to Primary, it enables support
for Primary PATA Controller.
When set to Secondary, it enables
support for Secondary PATA Controller.
Onboard S-ATA
Channels
Enables or disables the integrated
SATA Controller.
Enabled
Disabled
Download from Www.Somanuals.com. All Manuals Search And Download.
89
Parameter
Description
Option
Configure S-ATA
as RAID
When set to Enabled, the SATA
channels are reserved to be used as
RAID.
Disabled
Enabled
S-ATA Ports
Definition
Defines priority between SATA
channels.
A 1-3rd M/A
2-4th M
A 1-4th M/ A
2-3rd M
Mixed P-ATA/
S-ATA
Lets you remove a PATA and replace it
by SATA in a given channel. Only one
channel can be designated as SATA.
Press Enter to access the Mixed PATA/
SATA submenu.
Primary IDE
Master
Specifies the current configuration of
the IDE device connected to the master
port of the primary IDE channel.
Press Enter to access the Primary
Master submenu.
Primary IDE
Slave
Specifies the current configuration of
the the IDE device connected to the
slave port of the primary IDE channel.
Press Enter to access the Primary Slave
submenu.
Secondary IDE
Master
Specifies the current configuration of
the IDE device connected to the master
port of the secondary IDE channel.
Press Enter to access the Secondary
Master submenu.
Secondary IDE
Slave
Specifies the current configuration of
the IDE device connected to the slave
port of the secondary IDE channel.
Press Enter to access the Secondary
Slave submenu.
Third IDE
Master
Specifies the current configuration of
the IDE device connected to the master
port of the third IDE channel.
Press Enter to access the Third Master
submenu.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
90
Parameter
Description
Option
Fourth IDE
Master
Specifies the current configuration of
the IDE device connected to the master
port of the fourth IDE channel.
Press Enter to access the Fourth Master
submenu.
Hard Disk Write
Protect
Enables or disables write protection to
system hard drives.
Disabled
Enabled
IDE Detect Time
Out (Sec)
Select the time out value for detecting
ATA/ATAPI devices.
0
5
Used with older IDE devices with longer
spin up times.
15
20
25
30
35
ATA(PI) 80-pin
Cable
Select the mechanism for detecting 80-
pin ATA(PI) cable.
Host &
Device
Detection
Host
Device
Download from Www.Somanuals.com. All Manuals Search And Download.
91
Mixed P-ATA / S-ATA
The Mixed P-ATA/S-ATA submenu lets you specify the channel for the
Parallel ATA Primary channel and Serial ATA device.
Parameter
Description
Option
First/Second
ATA
Channel
Select channel mode.
P-ATA M-S
SATA M-S
3rd/4th ATA
Channel
Select channel mode.
A1-3rd M/A2-4th M
A1-4th M/A2-3rd M
None
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
92
Primary/Secondary/Third/Fourth IDE Master/Slave
These items let you select the IDE hard disk parameters that the system
supports.
Parameter
Device
Description
Option
Type of IDE device.
Vendor
Vendor of the selected IDE device.
Capacity of the selected IDE device.
LBA mode of the selected IDE device.
Block mode of the selected IDE device.
PIO mode of the selected IDE device.
Size
LBA Mode
Block Mode
PIO Mode
Async DMA
Async DMA mode of the selected IDE
device.
Ultra DMA
Ultra DMA mode of the selected IDE
device.
Download from Www.Somanuals.com. All Manuals Search And Download.
93
Parameter
Description
Option
S.M.A.R.T.
Indicates if the selected device
supports S.M.A.R.T. (Self-Monitoring,
Analysis and Reporting Technology)
function.
Type
Selects the drive type.
Auto
Not Installed
CD-ROM
ARMD
LBA/Large
Mode
Selects the hard disk drive translation
method. For drivers with more than
504 MB, LBA mode is necessary.
Auto
Disabled
Block
(Multi-Sector
Transfer) Mode
Enhances disk performance depending
on the hard disk in use.
Auto
Disabled
When set to Auto, the BIOS setup
automatically detects if the installed
hard disk drive supports the Block
Mode function. If supported, it allows
data transfer in blocks (multiple sectors
at a rate of 256 bytes per cycle).
When set to Disabled, data transfer
from and to the device occurs one
sector at a time.
PIO Mode
When set to Auto, the BIOS setup
automatically detects if the installed
hard disk supports the function. If
supported, it allows for faster data
recovery and read/write timing that
reduces hard disk activity time. This
results in better hard disk
Auto
0
1
2
3
4
performance.
Mode 0 to 4 provide progressive
increase of performance.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
94
Parameter
DMA Mode
Description
Option
Selects DMA (Direct Memory Access)
mode.
Auto
SWDMA0
SWDMA1
SWDMA2
MWDMA0
MWDMA1
MWDMA2
UDMA0
UDMA1
UDMA2
UDMA3
UDMA4
UDMA5
S.M.A.R.T.
Enables or disables the S.M.A.R.T.
function of the internal hard disk.
Auto
Disabled
Enabled
When set to Auto, the BIOS setup will
enable the S.M.A.R.T. function if the
drive supports it.
32Bit Data
Transfer
Enables or disables the 32-bit data
transfer function.
Disabled
Enabled
Download from Www.Somanuals.com. All Manuals Search And Download.
95
Floppy Configuration
The Floppy Configuration submenu displays the type of floppy drive
installed in the server.
Parameter
Description
Option
Floppy A
Floppy disk drive type.
1.44 MB 3 1/2”
2.88 MB 3 1/2”
720 KB 3 1/2”
Disabled
Onboard Floppy
Controller
Allows BIOS to enable or disable
the floppy controller.
Enabled
Disabled
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
96
Super I/O Configuration
The Super I/O Configuration submenu lets you define the parameter
settings for the system’s serial port.
Parameter
Description
Option
Serial Port A
Indicates the serial port 1 address and
IRQ setting.
3F8/IRQ4
Disabled
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Serial Port B
Indicates the serial port 2 address and
IRQ setting.
2F8/IRQ3
Disabled
3F8/IRQ4
3E8/IRQ4
2E8/IRQ3
Download from Www.Somanuals.com. All Manuals Search And Download.
97
USB Configuration
The USB Configuration submenu lets you specify settings for USB
devices.
Parameter
Description
Option
USB Function
Enables or disables the UBS host
controller.
Enabled
Disabled
When set to Disabled, other USB
options will be grayed out.
Legacy USB
Support
Enables or disables the support for
legacy USB devices.
Auto
Disabled
When set to Auto, the system detects
the presence of USB devices at startup.
Keyboard only
Keyboard and
Mouse
If a USB device is detected, the USB
controller legacy mode will be enabled.
Port 60/64
Emulation
Enables the I/O port 60/64h emulation
support.
Enabled
This parameter is enabled by default
and is not user-configurable.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
98
Parameter
Description
Option
USB 2.0
Enables the USB 2.0 controller.
Enabled
Controller
Disabled
USB 2.0
Controller
Mode
Sets the transfer rate at HiSpeed (480
Mbps) or FullSpeed (12 MBps).
HiSpeed
FullSpeed
USB Mass
Storage Device
Configuration
Lets you specify the settings of the USB
mass storage class devices.
Press Enter to access the USB Mass
Storage Device Configuration submenu.
USB Mass Storage Device Configuration
The USB Mass Storage Device Configuration submenu lets you specify
settings for a USB mass storage device, such as a USB CD-ROM,
CD-ROM/RW, DVD combo drive, and hard disk drives.
Parameter
Description
Option
USB Mass
Storage Reset
Delay
Select the number of seconds POST waits
for the USB mass storage device after the
start unit command.
20 Sec
10 Sec
30 Sec
40 Sec
Device #1
Type of USB mass storage device.
Emulation
Type
When set to Auto, USB mass storage
devices with less than 530 MB will be
emulated as a floppy and the remaining
drives are hard drives.
Auto
Floppy
Forced FDD
Hard Disk
CD-ROM
The Forced FDD option can be used to
force a formatted HDD to boot as a FDD.
Download from Www.Somanuals.com. All Manuals Search And Download.
99
PCI Configuration
The PCI Configuration submenu lets you specify settings that are
related to the onboard controllers.
Parameter
Description
Option
Onboard
Video
Enables or disables the onboard VGA
controller.
Enabled
Disabled
Dual Monitor
Video
Select a graphic controller as a primary
boot device.
Disabled
Enabled
Note: This parameter will be grayed out
when the Onboard Video is set to
Disabled.
Onboard NIC1
(Left)
Enables or disables the onboard NIC1
(Gigabit network interface controller).
Enabled
Disabled
Onboard NIC1
ROM
Enables or disables the onboard NIC1 ROM.
Enabled
Disabled
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
100
Parameter
Description
Option
Onboard NIC 2
(Right)
Enables or disables the onboard NIC2
(10Base-T/ 100Base/ 1000 Base network
interface controller).
Enabled
Disabled
Onboard NIC2
ROM
Enables or disables the onboard NIC2 ROM.
Enabled
Disabled
Onboard SCSI
Enables or disables the onboard SCSI
ontroller.
Enabled
Disabled
Onboard SCSI
ROM
Enables or disables the onboard SCSI ROM.
Enabled
Disabled
Onboard SCSI
Mode
Select a SCSI mode. Different RAID options,
such as RAID 0, RAID 1 or expanded RAID
arrays, are offered in the integrated SCSI
controller.
IM/IME
(RAID1/ 1e)
IS (RAID 0)
Slot 5 Option
ROM
Enables or disables the PCI 32/33 slot.
Enabled
Disabled
Download from Www.Somanuals.com. All Manuals Search And Download.
101
Memory Configuration
The Memory Configuration submenu provides information about the
DIMMs installed in DIMM slots 1A, 1B, 2A, and 2B.
Parameter
Description
Option
DIMM 1A, 1B,
2A and 2B
Indicates the current memory status.
Installed
Not
Installed
Disabled
Spare
Extended
Memory Test
Settings for extended memory test.
Disabled
1 MB
1 KB
Every
Location
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
102
Parameter
Description
Option
Memory
Retest
When Enabled, BIOS will activate and
retest all DIMMs on next boot.
Disabled
Enabled
Note: This parameter will automatically
reset to Disabled.
Memory
Remap
Feature
Enables or disables remapping of
overlapped PCI memory above the physical
memory.
Enabled
Disabled
Memory
Sparing
When set to Spare, a DIMM slot is kept in
reserve for standby in the event a
significant failure occurs in the primary
DIMM. If a threshold of runtime error
occurs in the primary DIMM, that DIMM
will have its data copied to the spare
DIMM.
Disabled
Spare
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
104
Boot Settings Configuration
The Boot Settings Configuration submenu lets you specify the
preferred settings for system bootup.
Parameter
Description
Option
Quick Boot
Allows the system to boot faster by
skipping some POST routine.
Enabled
Disabled
Quiet Boot
Enables or disables the Quiet Boot
function.
Disabled
Enabled
When set to Enabled, BIOS setup is in
graphical mode and displays only an
identification logo during POST and while
booting. After booting the screen displays
the operating system prompt (such as DOS)
or logo (such as Windows). If any error
occurs while booting, the system
automatically switched to text mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
105
Parameter
Description
Option
Bootup
Num-Lock
Activates the Numeric Lock function upon
booting.
Off
On
PS/2 Mouse
Support
Enable this parameter if you intend to use
a mouse or trackball with a PS/2 interface.
Auto
Enabled
Disabled
POST Error
Pause
When this parameter is Enabled, you will
be prompted when an error is detected
during boot up.
Enabled
Disabled
When set to Disabled, the system will boot
with no intervention, if possible.
Hit ‘F2’
Message
Display
When this parameter is Enabled, you will
be prompted to press F2 to run BIOS
during boot up.
Enabled
Disabled
Scan User Flash
Area
Allows BIOS to scan Flash ROM for user
binaries.
Disabled
Enabled
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
106
Boot Device Priority
The Boot Device Priority submenu lets you specify the boot search
sequence during the POST process.
BIOS setup will display an error message if the drive(s) specified is not
bootable.
Parameter
Description
1st Boot Device
Sets the device from which the system will first
attempt to boot up.
Press Enter to access the Removable Drives submenu.
2nd Boot Device
3rd Boot Device
Sets the device from which the system will attempt to
boot up when the first attempt failed.
Press Enter to access the CD/DVD Drives submenu.
Sets the device from which the system will attempt to
boot up when the first and second attempts failed.
Press Enter to access the Hard Disk Drives submenu.
Download from Www.Somanuals.com. All Manuals Search And Download.
107
Parameter
Description
4th and 5th Boot
Device
Sets the device from which the system will attempt to
boot up when the first, second and third attempts
failed.
Hard Disk Drives
The Hard Disk Drives submenu lets you specify the devices that will be
considered as the primary and secondary hard drives.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
110
Security
The Security menu allows you to safeguard and protect the system
from unauthorized use by setting up access passwords.
Parameter
Description
Option
Administrator
Password
Prevents unauthorized access to the
BIOS setup utility.
Not Installed
Installed
User Password
Secures the system against
Not Installed
unauthorized use. Once you set this
password, you have to type it
whenever you boot the system. User
password is available only when a
Supervisor password is set.
Installed
Set Admin
Password
Press Enter to change the Administrator
password.
Set User
Press Enter to change the User
Password
password.
Download from Www.Somanuals.com. All Manuals Search And Download.
111
Parameter
Description
Option
User Access
Level
When set to Full Access, allows access to
any field in the BIOS setup utility.
Full Access
No Access
View Only
Limited
When set to No Access, user is not
allowed to access the BIOS setup utility.
When set to View Only, allows access to
the BIOS setup utility but fields cannot
be changed.
When set to Limited, allows access to
Date and Time in the BIOS setup utility.
Clear User
Password
Clears the User password.
Note: This parameter is grayed out
when the Administrator password is not
set.
Fixed Disk
Boot Sector
Protect
Enable or disables Boot Sector Virus
Protection.
Disabled
Enabled
Password On
Boot
Select Enabled to activate security check
during POST.
Disabled
Enabled
NMI Control
Enables or disables NMI control.
Disabled
Enabled
Setting the Administrator/User password:
1
2
3
Use the up/down keys to highlight a password parameter
(Administrator Password or User Password) then press Enter.
A password box will appear.
Type a password then press Enter.
The password may consist of up to six alphanumeric characters
(A-Z, a-z, 0-9).
Retype the password to verify the first entry then press Enter
again.
After setting the password, the system automatically sets the
chosen password parameter to Installed.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
112
Removing the User password
1
Use the up/down keys to highlight the Clear User Password
parameter then press Enter.
2
3
Enter the current password then press Enter.
Press Enter twice without entering anything in the new and
confirm password fields.
After doing this, the system automatically sets the User password
parameter to Not Installed.
Download from Www.Somanuals.com. All Manuals Search And Download.
113
Server
The Server menu allows you to configure appropriate settings for
monitoring the server.
Parameter
Description
Option
System
Press Enter to access the System
Management
Management submenu.
Serial
Press Enter to access the Serial Console
Console
Features
Features submenu.
Event Log
Press Enter to access the Event Log
Configuration
Configuration.
Assert NMI on
SERR
Enables or disables the PCI bus SERR
(system error) support.
Enabled
Disabled
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
114
Parameter
Description
Option
Assert NMI on
PERR
Enables or disables the PCI bus PERR
(parity error) support.
Enabled
Disabled
Note: This parameter is disabled when
the NMI on SERR is disabled.
Resume on AC
Power Loss
Defines the mode of operation if a
power loss occurs.
Stays Off
Power On
When set to Stays Off, the system
remains off after power shutdown.
When set to Power On, the system will
turn on after power is restored.
Chassis Type
Indicates the chassis that controls the
speed of the system fan.
Other
System Management
The System Management submenu displays specific system
information. The screen below is for your reference only, system
configuration may vary.
Download from Www.Somanuals.com. All Manuals Search And Download.
115
Serial Console Features
The Serial Console Features submenu allows you to configure the serial
port settings.
Parameter
Description
Option
BIOS Redirection
Port
Specify the serial port where a
hardware console is connected.
Disabled
Serial A
Serial B
Baud Rate
Selects the baud rate or transfer
speed for console redirection.
19.2 K
9600
38.4 K
57.6 K
115.2 K
Flow Control
Selects a flow control for the system.
CTS/RTS: Hardware
CTS/RTS
XON/XOFF
CTS/RTS + CD
XON/XOFF: Software
CTS/RTS + CD: Hardware + Carrier
Detect for modem use
No Flow
Control
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
116
Parameter
Description
Option
Terminal Type
Specify the type of remote console.
VT100+
VT-UTF8
PC-ANSI
ACPI Redirection
Port
Specify the serial port where an ACPI
(Advanced Configuration and Power
Interface) console is connected.
Disabled
Serial A
Serial B
Download from Www.Somanuals.com. All Manuals Search And Download.
117
Event Log Configuration
The Event Log Configuration submenu allows you to record and
monitor events that occur in the system (e.g. system temperature
changes, fan stops, etc.).
Parameter
Description
Option
View Event Log
Opens the system Event log file for
viewing.
Clear Event Log
Discards all events in the Event log.
BIOS Event
Logging
Enables or disables the event logging
function of the sytem.
Enabled
Disabled
Critical Event
Logging
Enables or disables the critical event
logging function of the system. Critical
errors are fatal to system operation,
these include PERR, SERR and ECC.
Enabled
Disabled
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
118
Parameter
ECC Error Logging
Description
Option
Enables or disables the ECC (Error
Enabled
Correcting Code) event logging function
of the system. ECC tests the accuracy of
data as it passes in and out of memory.
Disabled
When this parameter is enabled,
single-bit and multi-bit memory errors
will be recorded in the event log.
PCI Error Logging
Enables or disables the PCI error logging.
Enabled
PCI (Peripheral Component Interconnect)
is a 32-bit bus that supports a 64-bit
extension for new processors, such as
Pentium processors. It can run at clock
speeds of 33 or 66 MHz.
Disabled
When this parameter is enabled, any PCI
device error will be recorded in the event
log.
FSB Error Logging
Enables or disables the FSB (Front-Side
Bus) error logging function of the sytem.
Enabled
Disabled
Hublink Error
Logging
Enables or disables the Hublink error
logging function of the system.
Enabled
Disabled
Download from Www.Somanuals.com. All Manuals Search And Download.
119
Exit
The Exit menu displays the various options to quit from the BIOS setup
utility. Highlight any of the exit options then press Enter.
Parameter
Description
Save Changes
and Exit
Saves changes made and close the BIOS setup utility.
The F10 key can also be used for this operation.
Discard
Changes and
Exit
Exits system setup without saving any changes.
The Esc key can also be used for this operation.
Discard
Discards changes made in the BIOS setup.
Changes
The F7 key can also be used for this operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
120
Parameter
Description
Load Setup
Defaults
Loads the default settings for all BIOS setup parameters.
Setup Defaults are quite demanding in terms of
resources consumption. If you are using low-speed mem-
ory chips or other kinds of low-performance components
and you choose to load these settings, the system might
not function properly.
The F9 key can also be used for this operation.
Load Custom
Defaults
Loads the custom settings for all BIOS setup parameters.
Save Custom
Defaults
Saves the custom settings for all BIOS setup parameters.
Download from Www.Somanuals.com. All Manuals Search And Download.
This chapter provides possible solutions for specific
problems. If you cannot correct the problem,
contact your local Acer representative or
authorized dealer for assistance.
Download from Www.Somanuals.com. All Manuals Search And Download.
123
Resetting the system
Before going through in-depth troubleshooting, attempt first to
perform reset the system using one of the methods below.
To do this
Press
Soft boot reset to clear the system memory and reload the
operating system.
Ctrl+Alt+Del
Cold boot reset. Turn the system power off and then on.
This clears system memory, restarts POST, reloads the
operating system and halts power to all peripherals.
Power off/on
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Troubleshooting
124
Problems following initial system
installation
Problems that occur at initial system startup are usually caused by an
incorrect installation or configuration. Hardware failure is a less
frequent cause. If the problem you are experiencing is with a specific
software application, see "There is problem with the application software"
on page 130.
Download from Www.Somanuals.com. All Manuals Search And Download.
125
First steps checklist
•
AC power available at the wall outlet?
•
Are the power supplies plugged in? Check the AC cable(s) on the
back of the chassis and at the AC source.
•
•
Are all cables correctly connected and secured?
Are the processors fully seated in their sockets on the server
board?
•
•
Are all standoffs in the proper location and not touching any
components, causing a potential short?
Are all add-in PCI boards fully seated in their slots on the server
board?
•
•
Are all jumper settings on the server board correct?
Are all jumper and switch settings on add-in boards and peripheral
devices correct? To check these settings, refer to the
manufacturer’s documentation that comes with them. If
applicable, ensure that there are no conflicts - for example, two
add-in boards sharing the same interrupt.
•
•
Are all peripheral devices installed correctly?
If the system has a hard disk drive, is it properly formatted or
configured?
•
•
•
Are all device drivers properly installed?
Are the configuration settings made in Setup correct?
Is the operating system properly loaded? Refer to the operating
system documentation.
•
•
Did you press the system power on/off switch on the control panel
to turn the server on (power on light should be lit)?
Is the system power cord properly connected to the system and
plugged into a NEMA 5-15R outlet for 100-120 V or a NEMA 6-15R
outlet for 200-240 V?
•
Are all integrated components from the tested components lists?
Check the tested memory, and chassis lists, as well as the supported
hardware and operating system list.
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Troubleshooting
126
Hardware diagnostic testing
This section provides a more detailed approach to identifying a
hardware problem and locating its source.
Caution! Turn off devices before disconnecting cables: Before
disconnecting any peripheral cables from the system, turn off the
system and any external peripheral devices. Failure to do so can
cause permanent damage to the system and/or the peripheral
devices.
1
Turn off the system and all external peripheral devices. Disconnect
each of device from the system, except for the keyboard and the
video monitor.
2
3
Make sure the system power cord is plugged into a properly
grounded AC outlet.
Make sure your video display monitor and keyboard are correctly
brightness and contrast controls to at least two thirds of their
maximum ranges (see the documentation supplied with your video
display monitor).
4
If the operating system normally loads from the hard disk drive,
make sure there is no diskette in drive A and no CD-ROM disk in
the CD-ROM drive.
5
6
If the power LED does light, attempt to boot from a floppy
diskette or from a CD-ROM disk.
Turn on the system. If the power LED does not light, see “Power
indicator does not light” on page 127.
Verifying proper operation of key system lights
As POST determines the system configuration, it tests for the presence
of each mass storage device installed in the system. As each device is
checked, its activity light should turn on briefly. Check for the
following:
Does the diskette drive activity light turn on briefly? If not, see "FDD
activity indicator does not light." on page 127.
Download from Www.Somanuals.com. All Manuals Search And Download.
127
Confirming loading of the OS
Once the system boots up, the operating system prompt appears on
the screen. The prompt varies according to the operating system. If the
operating system prompt does not appear, see "No Characters Appear
on Screen" on page 131.
Specific problems and corrective actions
The following contains specific problems that may arise during the use
of your server. Possible solutions are listed for each problem.
Power indicator does not light.
Do the following:
•
•
Make sure the power button on the front panel is turned on.
Make sure the hot-swap power supply module is propely installed.
Refer to “Upgrading the power supply” on page 72 for
instructions.
•
•
Make sure the power cable is connected correctly.
Make sure that the wall outlet has power. Test it by plugging
another device.
•
Remove all add-in cares and see if the system boots. If successful,
add the cards back in one at a time with a reboot between each
addition.
•
•
Make sure the memory modules comply with the system
requirements.
Make sure the memory modules have been populated according
to the system requirements.
•
•
•
Remove the memory modules and reseat them.
Make sure the CPU(s) comply with the system requirements.
Make sure the CPU(s) have been populated according to the
system requirements.
FDD activity indicator does not light.
Do the following:
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Troubleshooting
128
•
•
Make sure the FDD and signal cables are properly connected.
Check that relevant switches and jumpers for the FDD are set
correctly.
•
•
Check that FDD is properly configured.
If you are using the onboard diskette controller, use BIOS setup on
page 79 to make sure that onboard “Floppy A” is set to 1.44 MB,
3.5-inch.
HDD activity indicator does not light.
Do the following:
•
•
Make sure the drive is not disabled in the BIOS setup utility.
Make sure the drive’s power and data cables are connected
correctly.
•
•
Make sure the drive is compatible.
Make sure you have not exceeded the power budget for the
server.
•
•
•
If using SCSI drives, make sure that each SCSI ID number is unique
on the SCSI bus. See your drive documentation for details on
setting the SCSI ID for your drives.
If using SATA drives, make sure that the master or slave settings
are set correctly. See your drive documentation for details on
setting the master or slave settings.
If using a RAID configuration with SCSI or SATA drives, make sure
the RAID card is installed correctly.
HDD activity indicator does not light.
If you have installed one or more hard drives in the system, do the
following:
•
•
Make sure the power and signal cables are connected correctly.
Check that relevant switches and jumpers on the hard drive and
SCSI or SATA backplane board are set correctly.
Download from Www.Somanuals.com. All Manuals Search And Download.
129
CD drive activity indicator does not light.
Do the following:
•
•
Make sure the power and signal cables are properly installed.
Check that relevant switched and jumpers on the drive are set
correctly.
•
•
Check that drive is properly configured.
Check that onboard IDE controller is enabled in the BIOS setup.
CD tray cannot be ejected.
Do the following:
•
Insert the tip of a paperclip into the small hole on the CD drive.
Slowly pull the tray out from the drive until the tray is fully
extended then remove the disc.
CD drive cannot read a CD.
Do the following:
•
•
•
•
Make sure you are using the correct type of CD.
Make sure the CD is properly seated in the drive.
Make sure the disc is unscratched.
Make sure all cables are connected to the CD drive.
New memory modules installed are not detected.
Do the following:
•
•
•
Make sure the memory modules are properly seated on the DIMM
slots.
Make sure the memory modules comply with the system
requirements.
Make sure the memory modules have been populated according
to the system requirements.
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Troubleshooting
130
Network status indicator does not light.
Do the following:
•
Check the cabling and network equipment to make sure that all
cables are properly connected.
•
•
Reinstall the network drivers.
Try another port or hub on the switch.
Network activity indicator does not light.
Do the following:
•
•
Make sure the correct network drivers are loaded on the system.
Network might be idle. Try accessing the server.
Server hangs when the drivers are loaded.
Change the PCI interrrupt settings.
•
External device connected to a USB connector does not work.
Do the following:
•
•
Reduce the number of external devices connected to a USB hub.
Refer to the documentation that comes with the device.
There is problem with the application software.
Do the following:
•
•
Verify that the software is properly configured for the system.
Refer to the software installation and operation documentation
for instructions on setting up and using the software.
Try a different version of the software to see if the problem is with
the copy you are using.
•
•
Make sure all cables are properly connected.
If other software runs correctly on the system, contact your vendor
about the defective software.
Download from Www.Somanuals.com. All Manuals Search And Download.
131
No characters appear on the screen.
Check the following:
•
Is the keyboard functioning? Test it by turning the “Num Lock”
function on and off to make sure the Num Lock light is
functioning.
•
•
Is the video monitor plugged in and turned on? If you are using a
switch box, is it switched to the correct system?
Are the brightness and contrast controls on the video monitor
properly adjusted?
•
•
Is the video monitor signal cable properly installed?
Does this video monitor work correctly if plugged into a different
system?
•
•
Is the onboard video controller enabled in the BIOS?
Remove all add-in cares and see if the system boots. If successful,
add the cards back in one at a time with a reboot between each
addition.
•
•
Make sure the memory modules comply with the system
requirements.
Make sure the memory modules have been populated according
to the system requirements.
•
•
•
Remove the memory modules and reseat them.
Make sure the CPU(s) comply with the system requirements.
Make sure the CPU(s) have been populated according to the
system requirements.
If you are using an add-in video controller board, do the following:
1
2
Verify that the video works using the onboard video controller.
Verify that the video controller board is fully seated in the server
board connector.
3
4
Reboot the system for changes to take effect.
If there are still no characters on the screen after you reboot the
system and POST emits a beep code, write down the beep code
you hear. This information is useful for your service representative.
5
If you do not receive a beep code and characters do not appear,
the video display monitor or video controller may have failed.
Contact your service representative or authorized dealer for help.
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Troubleshooting
132
BIOS error messages
When a recoverable error occurs during POST, BIOS will display an error
message describing the problem.
The following table defines the error messages that may be displayed
if the system BIOS detects an error during POST.
Error message
Description
Memory BIOS messages
Gate20 error
An error occurred with Gate A20 when
switching to protected mode during the
memory test.
Multi-Bit ECC Error
A multiple bit corruption of memory has
occurred, and the ECC memory algorithm
cannot correct it.
Parity Error
Fatal Memory Parity Error.
Boot BIOS messages
Boot Failure
Could not boot from a particular device .
Invalid Boot Diskette
A diskette was found in the diskette drive,
but is not configured as a bootable
diskette.
Drive Not Ready
Corresponding drive is not ready for data
transfer.
A: Drive Error
No response from diskette drive.
Insert BOOT diskette in A:
Could not find a proper boot diskette in
drive A.
Reboot and Select proper Boot
device or Insert Boot Media in
selected Boot device.
Could not find a bootable device in the
system and/or removable media drive
does not contain media.
NO ROM BASIC
No bootable device was detected.
Download from Www.Somanuals.com. All Manuals Search And Download.
133
Error message
Description
Storage device BIOS messages
Primary Master/Slave Hard Disk
Error
Could not read sector from corresponding
drive.
Secondary Master/Slave Hard
Disk Error
3rd Master/Slave Hard Disk
Error
4th Master/Slave Hard Disk
Error
5th Master/Slave Hard Disk
Error
6th Master/Slave Hard Disk
Error
Primary Master/Slave Drive -
ATAPI Incompatible
Corresponding drive is not an ATAPI
device. Run Setup to make sure device is
selected correctly.
Secondary Master/Slave Drive -
ATAPI Incompatible
3rd Master/Slave Drive -
ATAPI Incompatible
4th Master/Slave Drive -
ATAPI Incompatible
5th Master/Slave Drive -
ATAPI Incompatible
6th Master/Slave Drive -
ATAPI Incompatible
S.M.A.R.T. capable but
Command Failed
Failed to send a S.M.A.R.T. message to a
hard disk.
S.M.A.R.T. Status BAD, Backup
and Replace
An imminent failure is detected by a
S.M.A.R.T. capable hard disk drive.
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Troubleshooting
134
Error message
Description
Virus related BIOS message
BootSector Write !!
A software attempting to write to a
drive’s boot sector has been detected. This
is flagged as possible virus activity. This
message will only be displayed if Virus
Detection is enabled in the BIOS setup.
VIRUS: Continue (Y/N)?
A possible virus activity is detected. This
message will only be displayed if Virus
Detection is enabled in the BIOS setup.
System configuration BIOS message
DMA-2 Error
Error during read/write test of the
secondary DMA controller.
DMA Controller Error
Error during read/write test of the DMA
controller.
Checking NVRAM..Update
Failed
Unable to write to the NVRAM block. This
message appears when the FLASH part is
write-protected or if there is no FLASH
part (System uses a PROM or EPROM).
Microcode Error
Unable to find or load the CPU Microcode
Update to the CPU.
NVRAM Checksum Bad,
NVRAM Cleared
Error while validating the NVRAM data.
Resource Conflict
NVRAM Ignored
NVRAM Bad
More than one system device is trying to
use the same non-shareable resources
(Memory or I/O).
The NVRAM data used to store plug-and-
play (PnP) data was not used for system
configuration in POST.
The NVRAM data used to store
Plug’n’Play (PnP) data was not used for
system configuration in POST due to a
data error.
Download from Www.Somanuals.com. All Manuals Search And Download.
135
Error message
Description
Static Resource Conflict
Two or more Static Devices are trying to
use the same resource space (usually
Memory or I/O).
PCI I/O conflict
PCI ROM conflict
PCI IRQ conflict
An I/O resource conflict was detected.
PCI IRQ routing table error
Timer Error
Unable to route an IRQ to the PCI device.
An error occurred while programming the
count register of channel 2 of the 8254
timer.
Interrupt Controller-1 error
Interrupt Controller-2 error
The Master Interrupt Controller could not
be initialized.
The Slave Interrupt Controller could not
be initialized.
CMOS BIOS message
CMOS Date/Time Not Set
The date and/or time values stored in the
CMOS are invalid. Run Setup to set correct
values.
CMOS Battery Low
The battery maybe losing power. Replace
the battery soon.
CMOS Settings Wrong
CMOS values are not the same as the last
boot. These values have either been
corrupted or the battery has failed.
CMOS Checksum Bad
The CMOS checksum is incorrect. CMOS
memory may have been corrupted. Run
Setup to reset values.
USB BIOS error messages
Warning! Unsupported USB
device found and disabled!
A non-bootable USB device is enumerated
and disabled.
Warning! Port 60h/64h
emulation is not supported by
this USB Host Controller!
The port 60h/64h emulation mode cannot
be enabled for this USB host controller.
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Troubleshooting
136
Error message
Description
Warning! EHCI controller
disabled. It requires 64bit data
support in the BIOS.
The EHCI controller is disabled because of
incorrect data structure. This condition
occurs if the USB host controller needs 64-
bit data structure while the USB is ported
with 32-bit data structure.
Miscellaneous BIOS messages
Keyboard Error
Error in the keyboard connection. Make
sure keyboard is connected properly.
Keyboard/Interface Error
PS2 Keyboard not found
PS2 Mouse not found
Unlock Keyboard
Keyboard interface test failed.
PS2 keyboard was not detected.
PS2 mouse was not detected.
PS2 keyboard is locked. To continue BIOS
POST, unlock the keyboard.
System Halted
Reset to reboot the system.
Not enough space in Runtime
area!!. SMBIOS data will not be
available.
The size of the SMBIOS data exceeds the
available SMBIOS runtime storage size.
Download from Www.Somanuals.com. All Manuals Search And Download.
137
POST error messages
The following table lists the error codes and associated conditions that
may occur during the POST portion of the BIOS.
Error code
0000
0003
0004
0005
0008
0009
000A
000B
000C
000E
000F
0010
0012
0014
0040
0041
0042
0043
0044
0045
Description
Timer error
CMOS battery low
CMOS settings wrong
CMOS checksum bad
Unlock keyboard
PS2 keyboard not found
KBC BAT test failed
CMOS memory size different
RAM R/W test failed
A: drive rrror
B: drive error
Floppy controller failure
CMOS date/time not set
PS2 mouse not found
Refresh timer test failed
Display memory test failed
CMOS display type wrong
<Ins> key pressed
DMA controller error
DMA-1 error
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Troubleshooting
138
Error code
Description
0046
0047
DMA-2 error
Unknown BIOS error. Error code = 147
(this is really a PMM_MEM_ALLOC_ERR)
0048
0049
Password check failed
Unknown BIOS error. Error code = 149
(this is really SEGMENT_REG_ERR)
004A
004B
Unknown BIOS error. Error code = 14A
(this is really ADM_MODULE_ERR)
Unknown BIOS error. Error code = 14B
(this is really LANGUAGE_MODULE_ERR)
004C
004D
004E
004F
0050
0055
0056
0057
0058
0059
005B
005D
005E
0120
0146
Keyboard/Interface error
Primary master hard disk error
Primary slave hard disk error
Secondary master hard disk error
Secondary slave hard disk error
Primary master drive - ATAPI incompatible
Primary slave drive - ATAPI incompatible
Secondary master drive - ATAPI incompatible
Secondary slave drive - ATAPI incompatible
Third master device error
Fourth master device error
S.M.A.R.T. status BAD, backup and replace
Password check failed
Thermal failure due to PROCHOT#
Insufficient memory to shadow PCI ROM
Download from Www.Somanuals.com. All Manuals Search And Download.
139
Error code
0150
0160
0161
0180
0181
0192
0193
0194
0195
0196
0197
5120
5121
51A2
51A3
Description
BSP processor failed BIST
Processor missing microcode – P0
Processor missing microcode – P1
BIOS does not support current stepping – P0
BIOS does not support current stepping – P1
L2 cache size mismatch
CPUID, processor stepping are different
CPUID, processor family are different
Front side bus mismatch
CPUID, processor model are different
Processor speeds mismatched
CMOS cleared by jumper
Password cleared by jumper
System cover has probably been opened.
System has probably been shut down with the
CPUTHRMTRIP# event.
8104
8105
Warning! Port 60h/64h emulation is not supported by this
USB host controller !!!
Warning! EHCI controller disabled. It requires 64bit data
support in the BIOS.
84FF
8500
8501
8502
System event log full
Bad or missing memory in slot 3A
Bad or missing memory in slot 2A
Bad or missing memory in slot 1A
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Troubleshooting
140
Error code
Description
8504
8505
8506
8508
Bad or missing memory in slot 3B
Bad or missing memory in slot 2B
Bad or missing memory in slot 1B
All memory marked as failed. Force all memory back online.
Download from Www.Somanuals.com. All Manuals Search And Download.
141
POST beep codes
The following table lists the error beep codes. Prior to system video
initialization, BIOS uses these beep codes to inform users of error
conditions. The beep code occurs only when a critical error occurs or
when the BIOS fails to boot to the operating system. Not all error
conditions are supported by the BIOS beep codes.
Number of
Description
beeps
1
2
3
4
5
6
Memory refresh timer error
Parity error in base memory (first 64KB block)
Base memory read/write test error
Timer not operational
Processor failure
8042 GateA20 cannot be toggled (memory failure or not
present)
7
Exception interrupt error
Display memory R/W error
ROM checksum error
8
9
10
11
CMOS shutdown register test error
Cache memory test failed
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Troubleshooting
142
Troubleshooting BIOS beep codes
The following table lists the possible beep codes thay may occur while
using the system and is followed by solutions to the situation.
Number of
Troubleshooting action
beeps
1, 2, or 3
√
√
√
j~âÉ=ëìêÉ=íÜÉ=ãÉãçêó=ãçÇìäÉë=~êÉ=éêçéÉêäó=ëÉ~íÉÇ=çå=íÜÉ=
afjj=ëäçíëK
j~âÉ=ëìêÉ=íÜÉ=ãÉãçêó=ãçÇìäÉë=Åçãéäó=ïáíÜ=íÜÉ=ëóëíÉã=
êÉèìáêÉãÉåíëK
j~âÉ=ëìêÉ=íÜÉ=ãÉãçêó=ãçÇìäÉë=Ü~îÉ=ÄÉÉå=éçéìä~íÉÇ=
~ÅÅçêÇáåÖ=íç=íÜÉ=ëóëíÉã=êÉèìáêÉãÉåíëK=
4-7, 9-11
√
√
fåÇáÅ~íÉë=~=Ñ~í~ä=ÉêêçêK=`çåëìäí=óçìê=ëóëíÉã=ã~åìÑ~ÅíìêÉêK=
fÑ=ÄÉÉé=ÅçÇÉë=~êÉ=ÖÉåÉê~íÉÇ=ÉîÉå=ïÜÉå=~ää=m`f=Å~êÇë=~êÉ=
~ÄëÉåíI=Åçåëìäí=óçìê=ëóëíÉã=ã~åìÑ~ÅíìêÉêÛë=íÉÅÜåáÅ~ä=
ëìééçêíK
√
`ÜÉÅâ=Ñçê=~=ã~äÑìåÅíáçåáåÖ=~ÇÇJáå=Å~êÇK=fÑ=ÄÉÉé=ÅçÇÉë=~êÉ=
åçí=ÖÉåÉê~íÉÇ=ïÜÉå=~ää=m`f=Å~êÇë=~êÉ=~ÄëÉåíI=çåÉ=çÑ=íÜÉ=
~ÇÇJáå=Å~êÇë=áë=Å~ìëáåÖ=íÜÉ=ã~äÑìåÅíáçåK=fåëÉêí=íÜÉ=Å~êÇë=
Ä~Åâ=áåíç=íÜÉ=ëóëíÉã=çåÉ=~í=~=íáãÉ=ìåíáä=íÜÉ=éêçÄäÉã=
Ü~ééÉåë=~Ö~áåK=
8
√
√
j~âÉ=ëìêÉ=íÜÉ=îáÇÉç=~Ç~éíÉê=áë=éêçéÉêäó=ëÉ~íÉÇ=çå=íÜÉ=
Éñé~åëáçå=ëäçíK=
fÑ=íÜÉ=îáÇÉç=~Ç~éíÉê=áë=~å=áåíÉÖê~íÉÇ=é~êí=çÑ=íÜÉ=ã~áåÄç~êÇI=
íÜÉ=Äç~êÇ=ã~ó=ÄÉ=Ñ~ìäíóK=
Download from Www.Somanuals.com. All Manuals Search And Download.
This appendix shows you how to install the
ASM software package and gives
information about the software program
and utilities bundled with your server.
Download from Www.Somanuals.com. All Manuals Search And Download.
145
Your Altos G5350 server supports the following system management
utilities:
•
ASM (Acer Server Manager)
This utility allows you to spot errors or potential trouble spots in
the network servers through a single management station. For
details go to page 147.
•
RAID configuration
The system may be bundled with a SCSI or SATA RAID
configuration utility. These utilities let you change the RAID
configuration of your SCSI or SATA hard disk. For details go to
page 149.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: System management utility
146
ASM
Acer Server Manager is a server management tool. It is specially
designed to help spot errors or potential trouble spots in the network
servers through a single management station. ASM can send a query to
a remote server over the network to request information such as
system hardware and software configuration, system resource usage,
and system performance.
The complete ASM package consists of two major components — the
ASM Agent and the ASM Console. The ASM Agent are the servers to be
managed on the network. The ASM Console is a Windows-based
monitoring station that communicates with the ASM Agents and can
be installed on any agent’s workstation on the network.
System requirements
ASM requires TCP/IP connectivity between the ASM Agent and the
ASM Console.
ASM Agent
•
Intel Pentium 4 (800 MHz), Intel Xeon (800 MHz), AMD
Opteron (1000 MHz) or higher processor
•
•
•
512 MB of RAM
SCSI/SATA hard drive with at least 100 MB free hard disk space
Microsoft Windows 2003 Server/Advanced Server operating system
ASM Console
•
Intel Pentium 4 (800 MHz), Intel Xeon (800 MHz), AMD
Opteron (1000 MHz) or higher processor
•
•
•
256 MB of RAM
SCSI/SATA hard drive with at least 100 MB free hard disk space
Microsoft Windows 2003 Professional/XP/Server/Advanced Server
operating system
Download from Www.Somanuals.com. All Manuals Search And Download.
147
System setup
Make sure that the system meets the requirements listed above before
proceeding. You may also want to change your screen resolution to
800 x 600 or higher for optimum viewing.
Installing ASM Agent
Follow the steps below:
1
2
Log in to the managed server using the Administrator account.
Insert the EasyBUILD Management CD into the server’s CD-ROM
drive. The installation sequence will automatically be displayed.
3
4
Select the option for ASM installation. The installation wizard will
be initialized.
Follow all onscreen instructions to complete the installation.
For detailed instructions on installing ASM Agent, refer to the
ASM User’s manual.
To launch the program, on the Windows taskbar click on the Start
button, point to Programs, select Acer Server Management Suite
then click ASM Agent.
Installing ASM Console
Follow the steps below:
1
Log in to the target Windows-based PC using the Administrator
account.
2
Insert the EasyBUILD Management CD into the computer’s
CD-ROM drive. The installation sequence will automatically be
displayed.
3
4
Select the option for ASM installation. The installation wizard will
be initialized.
Follow all onscreen instructions to complete the installation.
For detailed instructions on installing ASM Console, refer to the
ASM User’s manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: System management utility
148
To launch the program, on the Windows taskbar click on the Start
button, point to Programs, select Acer Server Management Suite
then click ASM Console.
Download from Www.Somanuals.com. All Manuals Search And Download.
149
RAID configuration
Caution! Using the RAID configuration utility erases all data
previously saved in the hard drives. Make sure that you backup
important files before starting the configuration process.
SCSI RAID configuration utility
The SCSI RAID configuration utility allows you to change the default
RAID configuration, such as the system volume of your SCSI hard disk.
For detailed information on how to use the SCSI RAID configuration
utility, refer to “Appendix D: SCSI RAID configuration” on page 173.
SATA RAID configuration utility
The SATA RAID configuration utility allows you to change the default
RAID configuration, such as system volume of your SATA hard disk.
For detailed information on how to use the SCSI RAID configuration
utility, refer to “Appendix C: SATA RAID configuration” on page 167.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: System management utility
150
Download from Www.Somanuals.com. All Manuals Search And Download.
This appendix shows you how to set up the
Altos G5350 server in a rack mount
configuration.
Download from Www.Somanuals.com. All Manuals Search And Download.
153
Setting up the system rack
Important! Observe the electrostatic discharge (ESD) precautions
indicated on page 35 when perfoming the following procedures.
Do not attempt the procedures described in the following sections
unless you are a qualified technician.
Equipment rack precautions
Follow the rack manufacturer's safety and installation instructions for
proper rack installation.
The following additional rack safety installation measures should be
considered:
•
Anchor the equipment rack
The equipment rack must be anchored to an unmovable suitable
support to prevent the rack from falling over when one or more
systems are fully extended out of the rack assembly. You must also
consider the weight of any other devices installed in the rack
assembly. The equipment rack must be installed according to the
manufacturer's instructions.
•
•
Main AC power disconnect
You are responsible for installing an AC power disconnect for the
entire rack unit. This main disconnect must be readily accessible,
and it must be labeled as controlling power to the entire unit, not
just to the system(s).
Earth ground the rack installation
To avoid the potential for an electrical shock hazard, the rack
assembly itself must be suitably earth grounded, according to your
local regional electrical codes. This typically will require the rack to
have its own separate earth ground. We recommend you consult
your local approved electrician.
Download from Www.Somanuals.com. All Manuals Search And Download.
154
•
Appendix B: Acer Altos G530 rack installation guide
Elevated operating ambient temperature
The maximum operating temperature of the system is 35 °C (95°F).
Careful consideration should be given to installing the system in
an environment compatible with the 35 °C (95°F) maximum
ambient temperature.
•
Reduced airflow
The amount of airflow required for the safe operation of the
equipment should not be compromised when installing the system
in a rack.
•
•
Mechanical loading
Exercise care when mounting the system in a rack to avoid any
accidents.
Circuit overloading
Appropriate consideration should be given when connecting the
supply circuit to the system to avoid any circuit overload. The
system name plate rating should be used when addressing
concerns about circuit overload.
Download from Www.Somanuals.com. All Manuals Search And Download.
155
System rack installation
The Altos G5350 server system can also be mounted in a rack-model
position. A rack mount kit is available for customers who want to
rack mount kit, contact your local Acer representative or order directly
The figure below shows the Altos G5350 server in a rack-mount
position.
Download from Www.Somanuals.com. All Manuals Search And Download.
156
Appendix B: Acer Altos G530 rack installation guide
Vertical mounting hole pattern
The four vertical rails of the system rack contain mounting holes
arranged in a manner shown in the figure below:
The system occupies 5U in the rack. Count the U positions and hole
numbers from the bottom up.
The distance from the center of two holes with closer spacing to the
center of the next pair is equivalent to 1U.
Note: The unit of measurement used in this guide is "U"
(1U = 1.75 inches or 44.45 mm). The total sum of the heights of all
components in the rack measured in "U" cannot exceed the
height of the rack. For more information, refer to the
documentation that came with the system rack.
When installing components, you must start your measurement from
the center of the two holes with closer spacing. Otherwise, the screw
holes on the component may not match those on the rack.
Download from Www.Somanuals.com. All Manuals Search And Download.
157
Screw types used
The following screws are used in the assembly of the Altos G5350
system and bundled rack-mountable components:
Screw type and
part number
Figure
Usage
#8-32 x 0.25 inch
Securing the inner mounting rails to
the system
Hex head
Securing the side handles to the
server
#6-32 0.25 inch
M4 x L8
M4 nut
Securing the mounting brackets to
the inner sliding piece
M6 x L10
•
•
•
Securing the cable arm to the
rack
Securing the component rail to
the rack
Securing the system
components to the rack
M6 cage nut
Supports the M6 metal screws for
securing system components to the
rack
Download from Www.Somanuals.com. All Manuals Search And Download.
158
Appendix B: Acer Altos G530 rack installation guide
Installing the system into the rack
Caution! To minimize the chances of injuries, make sure that two
or more people help in installing the server.
To install the system into a four-post rack
1
Remove the foot stands from the server.
(1) Lay the server on its side on a flat, stable surface (1).
(2) Remove the screws that hold the foot stands to the bottom of
the chassis (2). Keep these for later use.
(3) Pull the stands from the server.
Download from Www.Somanuals.com. All Manuals Search And Download.
159
2
Remove the inner rails from the mounting rails.
Note: The rack mount kit contains a pack of screws, two sets of
side handles, rack brackets and mounting rails. The side handles
are attached to the sides of the server. The rack brackets attach
the mounting rails to the server. The mounting rails allow the
server to slide in and out of the rackmount for maintenance
purposes. Each mounting rail consists of: an inner rail, a middle
slide, and a fixed outer rail. The fixed outer piece is screwed onto
the rack bracket with a M4 x L8 metal screw and nut, the inner rail
is attached to the sides of the server with the #8-32 screws and the
middle sliding piece controlled by a steel ball gearing movement.
(1) Extend the inner rail from the mounting rail until the rail
release latch clicks.
(2) Depress the release latch (1) and slip the inner rail out (2).
(3) Do the same thing to the other mounting rail.
Download from Www.Somanuals.com. All Manuals Search And Download.
160
3
Appendix B: Acer Altos G530 rack installation guide
Attach the inner rails to the mounting shelf.
(1) Align the inner rails to both sides of the mounting shelf (1).
(2) Secure the rails to the mounting shelf using ten #8-32 screws
(see page 157) (2).
4
Install the server into the mounting shelf.
Caution! To avoid personal injury, care should be taken when
pressing the inner rail release latches and sliding the component
into the rack.
(1) Place the server on the mounting shelf (1).
Download from Www.Somanuals.com. All Manuals Search And Download.
161
(2) Tighten the four thumbscrews on the rear of the mounting
shelf (2).
5
Install the rack brackets to the rack by following the steps below:
(1) Align the rack brackets to the mounting rail until the six screw
holes become visible.
(2) Secure the rack brackets to the mounting rails using six M4 x
L8 metal screws and nuts (see page 157).
Tighten the screws but leave them loose enough to allow
length adjustment when installing the mounting rails to the
rack.
(3) Attach the other rack brackets to the remaining mounting rail.
Download from Www.Somanuals.com. All Manuals Search And Download.
162
6
Appendix B: Acer Altos G530 rack installation guide
Install the M6 cage nuts (see page 157) into the rail.
(1) Insert the lower lip of the cage nut over the bottom of the
opening at the back of a rail.
(2) With your fingers, pinch the cage nut rack fastener and push
in until the top lip locks into position.
(3) Repeat this process to install the other cage nuts in their
appropriate locations.
Download from Www.Somanuals.com. All Manuals Search And Download.
163
7
Install the mounting rails to the rack by using four M6 x L10 metal
screws (see page 157) for each mounting rail.
8
Extend the middle sliding piece of each mounting rail forward
until you hear a click sound.
Download from Www.Somanuals.com. All Manuals Search And Download.
164
9
Appendix B: Acer Altos G530 rack installation guide
Install the server shelf assembly into the rack.
Caution! To avoid personal injury, care should be taken when
pressing the inner rail release latches and sliding the component
into the rack.
(1) Carefully align the inner rails attached to the mounting shelf
with the fully extended mounting rails on the rack.
(2) Press the release latch on both sides of the mounting shelf (1).
(3) Slide the mounting shelf into the rack, then push the
mounting shelf into the rack until you hear a click sound (2).
10 Attach the cable arm to the system.
The optional cable carm allows you to tie-wrap all cables to and
from the system. As you slide the system in and out of the rack, the
cable arm collapses and extends, keeping the cables untangled
and attached to the system.
Download from Www.Somanuals.com. All Manuals Search And Download.
165
(1) Attach the cable arm to the rear of the system using two M4 x
L8 metal screws and nuts (see page 157).
(2) Install two cage nuts into the rail to which the cable arm is to
be attached.
(3) Extend the cable arm enough to attach it to the rail using two
M6 x L10 metal screws (see page 157).
Download from Www.Somanuals.com. All Manuals Search And Download.
166
Appendix B: Acer Altos G530 rack installation guide
(4) Connect the power, peripheral and networking cables into
their appropriate ports (1).
Refer to “Connecting peripherals” on page 26 for detailed
instructions.
(5) Bundle all cables to the cable arm using the cable clamps (2).
Download from Www.Somanuals.com. All Manuals Search And Download.
This appendix shows you how to create a
RAID volume in your SATA drives.
Download from Www.Somanuals.com. All Manuals Search And Download.
169
Configuring the SATA RAID
This section shows how to create a RAID 1 (mirror) volume with the
onboard SATA RAID function. This feature requires the installation or
presence of a Intel 6300ESB ICH I/O controller.
Enabling the onboard SATA RAID function
1
2
Load the BIOS default settings
a
b
c
During bootup, press F2 to enter the BIOS setup screen.
Press F9 to restore the default settings.
Press F10 to save changes and exit setup.
Enable the onboard SATA RAID function
a
b
c
In the BIOS setup screen, select Advanced.
Select IDE Configuration, then press Enter.
Select Configure S-ATA as RAID, then press Enter to change
option to Enabled.
d
Press F10 to save changes and exit setup.
Using the SATA RAID configuration utility
Turn on the system. When prompted, press Ctrl+E to enter the
Embedded RAID configuration utility.
Loading the SATA RAID default setting.
1
In the Management menu, select Objects, then select Adapter.
The current adapter settings appear.
2
3
Select Factory Default, then Yes to load the default settings.
Press Ctrl+Alt+Del to reboot the server.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: SATA RAID configuration
170
Creating a RAID 1 volume
1
After rebooting the server, press Ctrl+E to enter the SATA RAID
Configuration screen. The Management menu appears.
2
3
Select Configuration. The Configuration menu appears.
Select New Configuration, then select YES. An array selection
window displays the devices connected to the current controller.
4
Use the arrow keys to select a specific drive, then press the
spacebar to associate the selected drive with the current array.
In the menu, the selected drive’s indicator will change from READY
to ONLINE A[array number]-[drive number].
For example ONLINE A1-2 means disk drive 2 in array 1.
5
6
7
Add two drives to the current array, then press Enter.
To select an array to configure, press Enter.
Press F10 to configure the logical drives. The default RAID level for
2 disk drives is RAID 1.
8
9
Select Accept to use t he default setting, then press Enter. The
Array Selection menu appears.
Press Enter again to end the array configuration.
10 Select YES to Save Configuration, and press any key to return to
the Configuration menu.
Initializing a RAID volume
1
2
3
Press Esc to return to the Management menu.
Select Initialize. All logical drives will appear under Logical Drives.
Using the spacebar, select the drive that you want to initialize. The
selected drive becomes yellow.
4
5
6
7
Press F10, then select YES to start initialization.
When initialization is complete, press any key to continue.
Press Esc to return to the Management menu.
To exit the utility and reboot the server, follow the steps below:
(a) In the Management menu, press Esc.
(b) Select YES.
Download from Www.Somanuals.com. All Manuals Search And Download.
171
(c) Press Ctrl+Alt+Del to reboot the server.
8
Install an Operating System to the RAID array.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: SATA RAID configuration
172
Download from Www.Somanuals.com. All Manuals Search And Download.
This appendix shows you how to create a
RAID volume in your SCSI drives.
Download from Www.Somanuals.com. All Manuals Search And Download.
175
Configuring the SCSI/SCSI RAID HBA
This section shows how to create a RAID 1 (mirror) volume. This feature
requires the installation or presence of a LSI Logic 1020A SCSI
controller.
Using the SCSI HBA setup utility
During bootup, press Ctrl+C to enter the LSI Logic Configuration
screen.
Loading the HBA default settings
1
2
3
4
5
6
In the LSI Logic MPT SCSI setup screen, press F2.
Select Global Properties, then select Restore Defaults.
Press Esc, then select Save changes then exit this menu.
Select 53C1020/53C1030, then press Enter.
Select Restore Defaults, then press Enter.
Press Esc, then select Save changes then exit this menu.
Using the SCSI RAID HBA setup utility
Creating a RAID 1 volume with a hot spare disk
1
In the LSI Logic MPT SCSI setup screen, select 53C1020/53C1030,
then press Enter.
2
3
Select RAID Properties, then press Enter.
In the Array Disk field, press the spacebar.
If you change the settings in the Array Disk field, the following
messages appear:
F3 - Keep Data (Create 2 disk arrays)
Delete - Erase Disk (Create 2 to 6 disk arrays)
Press the Delete key to erase all data on the screen.
In the Hot Spare field, press the spacebar.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: SCSI RAID configuration
176
If you change the settings in the Hot Spare field, the following
messages appear:
WARNING: Data on drive will be LOST!
Press DELETE if data loss OK or any other key to
cancel.
6
7
8
Press the Delete key to ignore.
Press Esc, then select Save changes then exit this menu.
To close the utility and reboot the server, follow the steps below:
(1) Press Esc, then select Exit the Configuration Utility.
The Global properties saved. Hit any key to
rebootmessage appears.
(2) Press any key to reboot the server.
RAID volume initialization
After you create the RAID volume and saved the changes, the disk
controller will automatically initialize the RAID volume. LSI Logic
1020A supports background initialization, there’s no need to wait for
the initialization to complete. Close the LSI Logic Configuration Utility
after saving the changes.
Using the MegaRAID configuration utility
Turn on the system. When prompted, press Ctrl+M to enter the
MegaRAID configuration utility. After a few seconds, the Management
menu appears.
Loading the RAID card default setting
1
In the Management menu, select Objects, then select Adapter.
The current adapter settings appear.
2
3
Select Factory Default, then Yes to load the default settings.
Press Ctrl+Alt+Del to reboot the server.
Download from Www.Somanuals.com. All Manuals Search And Download.
177
Creating a RAID 1 volume
1
After rebooting the server, press Ctrl+M to enter the MegaRAID
Configuration screen. The Management menu appears.
2
3
Select Configuration. The Configuration menu appears.
Select New Configuration, then select YES. An array selection
window displays the devices connected to the current controller.
4
Use the arrow keys to select a specific drive, then press the
spacebar to associate the selected drive with the current array.
In the menu, the selected drive’s indicator will change from READY
to ONLINE A[array number]-[drive number].
For example ONLINE A1-2 means disk drive 2 in array 1.
5
6
Add two drives to the current array, then press Enter.
Press F10 to configure the logical drives. The default RAID level for
2 disk drives is RAID 1.
7
8
9
Select Accept to use the default setting, then press Enter.
Press Enter again to end the array configuration.
Select YES to Save Configuration, and press any key to return to
the Configuration menu.
Assigning a hot spare disk
1
In the Configuration menu, select Add/View Configuration.
2
Use the arrow keys to select a specific drive, then press F4 to set
the drive as a hot spare disk.
3
Select YES. In the menu, the selected drive’s indicator will change
from READYto HOTSP.
4
5
Press Esc to end the array configuration.
Select YES to Save Configuration, then press any key to return
to the Configuration menu.
Initializing a RAID volume
1
2
3
Press Esc to return to the Management menu.
Select Initialize. All logical drives will appear under Logical Drives.
Using the spacebar, select the drive that you want to initialize. The
selected drive becomes yellow.
4
Press F10, then select YES to start initialization.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: SCSI RAID configuration
178
5
6
7
When initialization is complete, press any key to continue.
Press Esc to return to the Management menu.
To exit the utility and reboot the server, follow the steps below:
(a) In the Management menu, press Esc.
(b) Select YES.
(c) Press Ctrl+Alt+Del to reboot the server.
Install an Operating System to the RAID array.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
Acer Server Manager (ASM)
system requirements
ASM Agent 146
ASM Console 146
system setup 147
9
install ASM Agent 147
install ASM Console 147
B
BIOS setup 79
Advanced 84
Chipset 99
CPU 85
Floppy 95
I/O Device 96
IDE 88
Memory 101
PCI 98, 99
USB 97
USB Mass Storage Device 98
Boot 103
M
memory 64
ATAPI CD-ROM Devices 109
Boot Device Priority 106
Boot Settings Configuration
104
reconfiguring 69
removing 67
Hard Disk Drives 107
entering 80
Exit 119
Main 82
O
Security 110
removing the bezel 38
Administrator password 110
removing password 112
User password 110
Server
removing the left-side panel 37
Event Log Configuration 117
Serial Console Features 115
System Management 114
peripherals 26
power cable 27
power supply module
non-redundant 72
redundant 72
C
configuring the system OS 30
CPU 59
installing 59
removing 63
R
rack
D
installing 158
rack installation 151
DIMM population guidelines 65
CPU 1 67
cage nuts
installing 162
mounting pattern 156
precautions 153
screw type 157
RAID configuration 167, 173
E
expansion card 70
installing 70
Download from Www.Somanuals.com. All Manuals Search And Download.
180
MegaRAID utility 176
assign hot spare 177
create RAID 1 177
initialize RAID volume 177
RAID volume
replacing CD-ROM drive 55
system boards 14
initialization 176
SATA HBA utility 169
SATA RAID utility
mainboard layout 14
create RAID 1 170
enable 169
initialize RAID volume 170
load default settings 169
SCSI HBA utility 175
load default 176
load default settings 175
SCSI RAID HBA utility 175
create RAID 1 175
rear panel 10
S
setting up the system 25
specification
additional media storage
4
cannot eject CD tray 129
cannot read CD 129
SATA HDD cage
SCSI HDD cage
4
4
CD drive no light 129
chipset
graphic interface
3
FDD LED no light 127
5
HDD LED no light 128
I/O ports
media storage
memory subsystem
networking
OS
PCI I/O
power supply
processor
RAID
SATA controller
5
initial system installation 124
LAN LED no light 130
3
3
memory not detected 129
no characters on screen 131
power indicator no light 127
resetting the system 123
verifying key system lights 126
turning off the system 32
turning on the system 27
power-on problems 29
4
5
4
5
3
4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|