Integrated High Definition
Color Television
26HF66
J3W60321A_En_cov
1
27/2/06, 12:34 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
Installation, Care, and Service
Installation
Follow these recommendations and precautions and heed all
warnings when installing your TV:
4) Follow all instructions.
16) Never modify this equipment. Changes or modifications
may void: a) the warranty, and b) the user’s authority to
operate this equipment under the rules of the Federal
Communications Commission.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in
17)
DANGER: RISK OF SERIOUS PERSONAL
INJURY, DEATH, OR EQUIPMENT
DAMAGE! Never place the TV on
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
an unstable cart, stand, or table. The TV
may fall, causing serious personal injury,
death, or serious damage to the TV.
9) Do not defeat the safety purpose of the polarized or
grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding prong.
18) Never place or store the TV in direct
sunlight; hot, humid areas; areas
subject to excessive dust or vibration;
or locations with temperatures at or
below 41°F (5°C).
The wide blade or the third prong are
Wide plug
provided for your safety. If the provided
plug does not fit into your outlet, consult
an electrician for replacement of the
obsolete outlet.
19) Always place the TV on the floor
or a sturdy, level, stable surface that
can support the weight of the unit.
10) Protect the power cord from being
walked on or pinched, particularly at
plugs, convenience receptacles, and
the point where it exits the apparatus.
20) Never place items such as vases,
aquariums, or candles on top of the TV.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
21) Never block or cover the slots or
openings in the TV cabinet back,
bottom, and sides. Never place
the TV:
apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
• on a bed, sofa, rug, or similar
13) Unplug this apparatus during
lightning storms or when
unused for long periods
of time.
surface;
• too close to drapes, curtains,
or walls; or
• in a confined space such as a
bookcase, built-in cabinet, or any
other place with poor ventilation.
The slots and openings are provided
to protect the TV from overheating
and to help maintain reliable
operation of the TV.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in
any way, such as power supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
22) Always place the back of the television at least one (1)
inch away from any vertical surface (such as a wall) to
allow proper ventilation.
14a)CAUTION: If the TV is dropped and the cabinet or
enclosure surface has been damaged or the TV does not
operate normally, take the following precautions:
• ALWAYS turn off the TV and unplug the power cord to avoid
possible electric shock or fire.
23) Never allow anything to rest on or roll over the power
cord, and never place the TV where the power cord is
subject to wear or abuse.
• To prevent personal injury, never handle the damaged
television.
• ALWAYS contact a service technician to inspect the TV any
time it has been damaged or dropped.
24) Never overload wall outlets and
extension cords.
15)
CAUTION: To reduce the risk of electric shock, do
not use the polarized plug with an extension cord,
receptacle, or other outlet unless the blades can
be inserted completely to prevent blade exposure.
0303
3
J3W60321A_En_p02-06
3
27/2/06, 9:53 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
31) [This item applies to projection TVs only.] If the air
temperature rises suddenly (for example, when the TV is
first delivered), condensation may form on the lenses. This
can make the picture appear distorted or the color appear
faded. If this happens, turn off the TV for 6 to 7 hours to
allow the condensation to evaporate.
25) Always operate this equipment from
a 120 V AC, 60 Hz power source only.
32) For added protection of your TV from lightning and power
surges, always unplug the power cord and disconnect the
antenna from the TV if you leave the TV unattended or
unused for long periods of time.
26) Always make sure the antenna system is properly
grounded to provide adequate protection against voltage
surges and built-up static charges (see Section 810 of the
National Electric Code).
Antenna lead-in wire
33) During normal use, the TV may make
occasional snapping or popping
Antenna discharge unit
(NEC Section 810-20)
Ground clamp
sounds. This is normal, especially
when the unit is being turned on or
off. If these sounds become frequent
or continuous, unplug the power cord
and contact a Toshiba Authorized Service Center.
Grounding conductors
(NEC Section 810-21)
Electric service equipment
34)Possible Adverse Effects on TV Picture Display: If a
fixed (non-moving) pattern or image remains on the TV
screen for extended periods of time, the image can
become permanently ingrained in the cathode ray tube(s)
of the TV and cause subtle but permanent ghost images.
This type of damage is NOT COVERED BY YOUR
WARRANTY. Never leave the TV on for extended periods of
time while it is displaying the following images or formats:
• Fixed Images, including but not limited to PIP/POP
windows, closed captions, video game patterns, TV
station logos, stock tickers, and websites.
Power service grounding
electrode system (NEC Art 250 Part H)
Ground clamps
27)
DANGER: RISK OF SERIOUS PERSONAL
INJURY OR DEATH!
• Use extreme care to make sure you are never in
a position where your body (or any item you are in contact
with, such as a ladder or screwdriver) can accidentally
touch overhead power lines. Never locate the antenna
near overhead power lines or other electrical circuits.
• Never attempt to install any of the following during
lightning activity:
a) an antenna system; or b) cables, wires, or any home
theater component connected to an antenna or phone
system.
• Special Formats that do not use the entire screen,
including but not limited to widescreen or letterbox
format media viewed on a 4:3 aspect ratio display (with
gray or black bars at the top and bottom of the screen);
or 4:3 aspect ratio format media viewed on a
widescreen/16:9 aspect ratio display (with gray or black
bars on the left and right sides of the screen).
Care
Service
35)
For better performance and safer operation of your TOSHIBA
TV, follow these recommendations and precautions:
WARNING: RISK OF ELECTRIC
SHOCK! Never attempt to service the
TV yourself. Opening and
28) Always sit approximately 10–25 feet away from the TV and
as directly in front of it as possible. The picture can appear
dull if you sit too far to the left or right of the TV, or if
sunlight or room lights reflect on the screen. Turn the TV
off to check for reflections on the screen, and then remove
the source of reflections while viewing the TV.
removing the covers may expose
you to dangerous voltage or other
hazards. Refer all servicing to a
Toshiba Authorized Service Center.
QUALIFIED
SERVICE
TECHNICIAN
36) If you have the TV serviced:
• Ask the service technician to use only replacement parts
specified by the manufacturer.
• Upon completion of service, ask
the service technician to perform
routine safety checks to determine
that the TV is in safe operating
condition.
29) Always unplug the TV before
cleaning. Never use liquid or
aerosol cleaners.
37) When the TV reaches the end of its useful life, ask a
qualified service technician to properly dispose of the TV.
Improper disposal may result in a picture tube implosion
and possible personal injury.
30)
WARNING: RISK OF ELECTRIC SHOCK!
Never spill liquids or push objects of any kind
into the TV cabinet slots.
0303
4
J3W60321A_En_p02-06
4
27/2/06, 9:53 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safeguards ............................................................................................................. 2-4
Welcome to Toshiba ................................................................................................................... 6
Exploring your new TV ................................................................................................................................................... 6
Selecting a location for the TV ....................................................................................................................................... 6
Connecting your TV ................................................................................................................... 7
Connecting a VCR ......................................................................................................................................................... 7
Connecting a cable converter box or Antenna ............................................................................................................... 8
Connecting a DVD player/satellite receiver and a VCR ................................................................................................. 9
Connecting a DVD player with ColorStream® (component video) and a VCR ............................................................. 10
Connecting a DTV receiver / set-top box with ColorStream® (component video) and a VCR ...................................... 11
Connecting a camcorder .............................................................................................................................................. 12
Connecting an HDMI™ or DVI device .......................................................................................................................... 13
Connecting an audio system........................................................................................................................................ 14
Connecting an A/V amplifier with built-in digital surround ............................................................................................ 14
Using the remote control......................................................................................................... 15
Preparing the remote control for use ........................................................................................................................... 15
Installing the remote control batteries .......................................................................................................................... 15
Using the remote control to operate your other devices .............................................................................................. 15
Programming the remote control to operate your other devices .................................................................................. 16
Device code tables ....................................................................................................................................................... 17
Learning about the remote control ............................................................................................................................... 19
Setting up your TV.................................................................................................................... 20
Starting setup............................................................................................................................................................... 20
Changing the on-screen display language ................................................................................................................... 20
Image tilt correction...................................................................................................................................................... 21
Adding channels to the TV’s memory .......................................................................................................................... 21
Using the TV’s features ............................................................................................................ 22
Adjusting the channel settings ..................................................................................................................................... 22
Using the LOCKS menu............................................................................................................................................... 23
Selecting a password .......................................................................................................................................... 23
Using the V-Chip (parental control) feature ......................................................................................................... 24
Locking channels ................................................................................................................................................ 25
Locking the video inputs...................................................................................................................................... 26
Setting the GameTimerTM .................................................................................................................................... 26
Using the front panel lock feature ....................................................................................................................... 27
Labeling channels ........................................................................................................................................................ 27
Selecting the video input source .................................................................................................................................. 28
Labeling the video input sources ................................................................................................................................. 28
Setting the clock........................................................................................................................................................... 29
Setting the ON/OFF timer ............................................................................................................................................ 29
Viewing the wide-screen picture formats (480i and 480p signals only) ....................................................................... 30
Scrolling the TheaterWide® picture (TheaterWide 2 and 3 only) .................................................................................. 32
Selecting the cinema mode.......................................................................................................................................... 33
Selecting the display format (for 480p signals only)..................................................................................................... 33
Adjusting the picture .................................................................................................................................................... 33
Selecting the picture mode ................................................................................................................................. 33
Adjusting the picture quality ................................................................................................................................ 34
Selecting the color temperature .......................................................................................................................... 34
Using the CableClear® feature ............................................................................................................................ 35
Selecting the Scan Velocity Modulation (SVM) ................................................................................................... 35
Resetting your picture adjustments ..................................................................................................................... 35
Setting the sleep timer ................................................................................................................................................. 36
Using the closed caption feature.................................................................................................................................. 36
Using the CC advanced feature ................................................................................................................................... 36
Adjusting the sound ..................................................................................................................................................... 37
Muting the sound ................................................................................................................................................ 37
Selecting stereo/SAP broadcasts ....................................................................................................................... 37
Adjusting the sound quality ................................................................................................................................. 37
Using the StableSound® feature .......................................................................................................................... 38
Turning off the built-in speakers .......................................................................................................................... 38
Selecting the HDMI™ audio input source ........................................................................................................... 38
Using the BBE® sound feature ............................................................................................................................ 39
Selecting the audio languages ............................................................................................................................ 39
Selecting the digital output format....................................................................................................................... 39
Resetting your audio adjustments ....................................................................................................................... 40
Checking the digital signal strength ............................................................................................................................. 40
Displaying TV status information on-screen ................................................................................................................. 40
Auto power off .............................................................................................................................................................. 41
Understanding the Power Return feature..................................................................................................................... 41
Appendix................................................................................................................................... 41
Troubleshooting ............................................................................................................................................................ 41
Specifications ............................................................................................................................................................... 42
Limited United States Warranty.................................................................................................................................... 43
5
J3W60321A_En_p02-06
5
27/2/06, 9:53 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Welcome to Toshiba
Congratulations! You have purchased one of the finest color TVs on the
market. The goal of this manual is to guide you through setting up and
operating your Toshiba TV as quickly as possible.
The STARTING SETUP feature appears
the first time you turn on the TV. See page
20 for details.
You may need to purchase other audio or video cables to connect your
equipment. See “Connecting your TV” on page 7 for more information.
Please read all the safety and operating instructions carefully before
you begin.
Exploring your new TV
You can operate your TV by using the buttons on the front panel or the
remote control. The front and back panels provide all the inputs you will
need to connect other equipment to your TV.
TV front panel
Audio(L/R)/Video In
S-video In
Remote sensor
Channel
Volume
POWER Power indicator
TV back panel
Selecting a location for the TV
• Place the TV on the floor or on a sturdy platform in a location where
light does not directly hit the screen.
•
Place the TV far enough from the walls to allow proper ventilation.
Inadequate ventilation may cause overheating, which may damage the
TV. This type of damage is NOT COVERED BYYOUR WARRANTY.
6
J3W60321A_En_p02-06
6
27/2/06, 9:53 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your TV
NEVER CONNECTTHISTVTO A
PERSONAL COMPUTER (PC).
ThisTV is not intended for use
with a PC.
• A coaxial cable is the standard cable that comes in from your
antenna or cable converter box. Coaxial cables use “F” connectors.
• Standard A/V (audio/video) cables are usually color coded accord-
ing to use: yellow for video and red and white for audio. The red
audio cable is for the stereo right channel, and the white audio
cable is for the stereo left (or mono) channel. If you look at the rear
panel of the TV, you will see that the terminals are color coded in
the same manner as the cables.
• S-video cables provide better picture performance than standard
video cables. S-video cables can only be used with S-video
compatible components.
• Component video cables provide better picture performance than
S-video cables. Component video cables can only be used with
component video compatible components.
NOTICE: RISK OF
• HDMITM (High Definition Multimedia Interface) cable is for use with
video equipment that has HDMI output (see page 13).
• Digital audio coaxial cable is for use with digital audio equipment
that has digital audio output (see page 14).
EQUIPMENT DAMAGE!
Do not plug in any power cords
until you have finished connecting
all equipment.
Connecting a VCR
This connection allows you to watch local channels and video programs,
play or record on the VCR while watching TV, and record from one
channel while watching another channel.
You will need:
• two coaxial cables
• one set of standard A/V cables
Back panel of TV
Note:
If using a mono VCR, connect L/Mono to
VCR Audio OUT using only one audio cable.
For better picture quality, if your VCR has
S-video, you can use an S-video cable
instead of the standard video cable. Do not
connect a standard video cable and an
S-video cable to VIDEO-1 (or VIDEO-2 or
VIDEO-3) simultaneously or the picture
performance will be unacceptable.
Cable Lead-in
from cable box
or antenna
The unauthorized recording, use, distri-
bution or revision of television programs,
videotapes, DVDs, and other materials is
prohibited under the Copyright Laws of
the United States and other countries,
and may subject you to civil and criminal
liability.
Stereo VCR
7
J3W60321A_En_p07-14
7
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a cable converter box or Antenna
This television has an extended tuning range and can tune most cable
channels without using a cable company supplied converter box. Some
cable companies offer “premium pay channels” in which the signal is
scrambled. Descrambling these signals for normal viewing requires the
use of a descrambler device, which is generally provided by the cable
company.
Option 1: For Subscribers to Basic Cable TV Service
For basic cable service not requiring a Converter/Descrambler box,
connect the incoming 75 ohm Coaxial Cable directly to the Antenna
Jack on the back of the television.
Option 2: For Subscribers to Scrambled Cable TV Service
If you subscribe to a cable service that requires the use of a Converter/
Descrambler box, connect the incoming cable to the Converter/
Descrambler box and connect the output of the box to the Antenna
Jack on the back of the television. Follow the connections shown below.
Set the television to the output of the Converter/Descrambler box
(usually channel 3 or 4) and use the Converter/Descrambler box to
select channels.
Option 3: For Subscribers to Unscrambled Basic Cable with
Scrambled Premium Channels
If you subscribe to a cable service in which basic cable channels are
unscrambled and premium channels require the use of a Converter/
Descrambler box, you may wish to use a two-set signal splitter (some-
times called a “two-set coupler”) and an A/B Switch box from the cable
installer or an electronics supply store. Follow the connections shown
below. With the switch in the “B” position, you can directly tune any
nonscrambled channels on your TV. With the switch in the “A” position,
tune your TV to the output of the Converter/Descrambler box (usually
channel 3 or 4) and use the box to tune scrambled channels.
Note:
When you use a converter box with your TV,
there may be features that you cannot
program using the remote control, such as
labeling channels, blocking channels, and
programming your favorite channels.
From cable
Option 1:
Back panel of TV
Option 2:
Option 3:
8
J3W60321A_En_p07-14
8
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a DVD player/satellite receiver
and a VCR
This connection allows you to watch DVD/satellite, VCR, or TV
programs.You can record from the satellite receiver and TV, as well as
record one TV channel while watching another channel.
You will need:
• three coaxial cables
• two sets of standard A/V cables
• one S-video cable
Note:
You can use a standard video cable instead
of the S-video cable, but the picture quality
will decrease. If you use an S-video cable
between the TV and DVD player/satellite
receiver, make the audio connections but
remove the standard video cable. Do not
connect both an S-video and a standard
video cable to VIDEO-1 (or VIDEO-2 or
VIDEO-3) at the same time or the picture
performance will be unacceptable.
From satellite
DVD player / Satellite Receiver
VIDEO
AUDIO
L
R
OUT
Satellite IN
S-VIDEO
OUT to TV
The unauthorized recording, use, distri-
bution or revision of television programs,
videotapes, DVDs, and other materials is
prohibited under the Copyright Laws of
the United States and other countries,
and may subject you to civil and criminal
liability.
Stereo VCR
IN
IN from ANT
OUT to TV
OUT
CH
CH
3
4
VO
UDIO
Back panel of TV
9
J3W60321A_En_p07-14
9
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a DVD player with ColorStream®
(component video) and a VCR
This connection allows you to watch DVD, VCR, or TV programs and
record TV programs.You can record from one source while watching a
program from another source.Your TV has ColorStream® (component
video) inputs. Connecting your TV to a component video compatible DVD
player, such as a Toshiba DVD player with ColorStream®, can greatly
enhance picture quality and performance.
You will need:
• two coaxial cables
• one set of standard A/V cables
• one set of component video cables
• one pair of standard audio cables
Note:
You can connect the component video cables
to either set of ColorStream jacks on the TV
(HD-1 or HD-2).
DVD player with Component video
The ColorStream HD-1 and HD-2 jacks can
be used with Progressive (480p, 720p) and
Interlaced (480i, 1080i) scan systems. A
1080i signal will provide the best picture
performance.
OUT
L
COMPONENT VIDEO
Y
R
VIDEO
OUT
AUDIO
S-VIDEO
Back panel of TV
The unauthorized recording, use, distri-
bution or revision of television programs,
videotapes, DVDs, and other materials is
prohibited under the Copyright Laws of
the United States and other countries,
and may subject you to civil and criminal
liability.
From
antenna
Stereo VCR
IN
IN from ANT
OUT to TV
OUT
CH
CH
3
4
L
R
VIDEO
AUDIO
10
J3W60321A_En_p07-14
10
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a DTV receiver / set-top box with
ColorStream® (component video) and a VCR
You will need:
• three coaxial cables
This connection allows you to watch DTV (digital TV), VCR, and TV
programs, and record DTV and TV programs.
• two sets of standard A/V cables
• one set of standard audio cables
• one set of component video cables
Your TV has ColorStream® (component video) inputs. Connecting your
TV to a DTV receiver with component video can greatly enhance
picture quality and realism.
Note:
You can connect the component video cables
to either set of ColorStream jacks on the TV
(HD-1 or HD-2).
From antenna
Stereo VCR
The ColorStream HD-1 and HD-2 jacks and
HDMI jacks can be used with Progressive
(480p, 720p) and Interlaced (480i, 1080i)
scan systems. A 1080i signal will provide the
best picture performance.
IN
IN from ANT
OUT to TV
OUT
CH
CH
3
4
If your DTV receiver does not have compo-
nent video, use the S-video and standard
audio connections instead. Do not connect
both an S-video and a standard video cable
to VIDEO-1 (or VIDEO-2 or VIDEO-3) at the
same time or the picture performance will be
unacceptable.
VIDEO
AUDIO
Back panel of TV
For HDMI connection, see page 13.
The unauthorized recording, use,
distribution, or revision of television
programs, videotapes, DVDs, and other
materials is prohibited under the
Copyright Laws of the United States and
other countries, and may subject you to
civil and criminal liability.
From DTV
antenna
AUDIO
OUT
L
Y
S-VIDEO
COMPONENT VIDEO
VIO
OT
R
DTV Receiver
with Component video
11
J3W60321A_En_p07-14
11
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a camcorder
This connection allows you to watch videos recorded on a camcorder.
VHS Camcorder
You will need:
• one set of standard A/V cables
Front panel of TV
S-VHS Camcorder
You will need:
• one S-video cable
• one pair of standard audio cables
AUDIO
L
S-VIDEO
VIDEO
Note:
For better picture quality, if your camcorder
has S-video, you can use an S-video cable
(plus the standard audio cables) instead of a
standard video cable. Do not connect both a
standard video cable and an S-video cable at
the same time or the picture performance will
be unacceptable.
R
OUT
Front panel of TV
12
J3W60321A_En_p07-14
12
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting an HDMI™ or DVI device
The HDMI (High-Definition Multimedia Interface) input on
your TV receives digital audio and uncompressed digital
video from an HDMI source device, or uncompressed
digital video from a DVI (Digital Visual Interface) source
device.
[1] EIA/CEA-861/861B compliance covers the
transmission of uncompressed digital video with high-
bandwidth digital content protection, which is being
standardized for reception of high-definition video
signals. Because this is an evolving technology, it
is possible that some devices may not operate
properly with theTV.
This input is designed to accept HDCP (High-bandwidth
Digital Content Protection) program material in digital form
from EIA/CEA-861/861B-compliant[1] consumer electronic
devices (such as a set-top box or DVD player with HDMI or
DVI output).
To ensure that the HDMI or DVI device is reset
properly, it is recommended that you follow these
procedures:
• When turning on your electronic components, turn
on the TV first, and then the HDMI or DVI device.
• When turning off your electronic components, turn
off the HDMI or DVI device first, and then the TV.
The HDMI input is designed for best performance with high
definition video signals. It will accept and display 480i,
480p, 720p and 1080i signals.
NEVER CONNECTTHISTVTO A PERSONAL
COMPUTER (PC).ThisTV is not intended for
use with a PC.
To connect a DVI device, you will need:
• one HDMI-to-DVI adapter cable
(HDMI type A connector)
To connect an HDMI device, you will need:
• one HDMI cable (type A connector)
For proper operation, the length of an HDMI-to-DVI
adapter cable should not exceed 9.8 ft (3m). The
recommended length is 6.6 ft (2m).
For proper operation, it is recommended that you use
as short an HDMI cable as possible.You should not
encounter difficulty if you use an HDMI cable that is
shorter than 16.4 ft (5m).
• one pair of standard analog audio cables
An HDMI-to-DVI adapter cable transfers only video.
Separate analog audio cables are required (see
illustration below).
HDMI cable transfers both video and audio. Separate
analog audio cables are not required (see illustration
below).
You must set the HDMI audio input setting to
“HDMI” in the AUDIO menu (see page 38).
You must set the HDMI audio input setting to
“DVI” in the AUDIO menu (see page 38).
Some CDVs (Video CDs) may not output digital audio
signals. In that case, you may hear sound by connecting
analog audio cables. If you do use analog audio cables for
this reason, you will need to set the HDMI audio input
setting to “DVI” to hear the analog audio (see page 38).
Note: If you connect an HDMI device and analog audio
cables and play media with digital audio output, to hear
digital audio you must set the HDMI audio input setting
to “HDMI” (page 38).
DVI device
DVI
OUT
VIDEO
AUDIO
L
R
IN
OUT
Back panel of TV
HDMI device
Back panel of TV
HDMI, the HDMI logo, and High-Definition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing, LLC.
13
J3W60321A_En_p07-14
13
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting an audio system
This connection allows you to use external speakers with an external
audio amplifier to adjust the sound level.
You will need:
• one pair of standard audio cables
To control the audio:
Turn on the TV and the stereo amplifier.
Turn off the TV’s built-in speakers (see “Turning off the built-in
speakers” on page 38).
Note: To hear sound when using an external audio amplifier, the
volume of both the TV and the amplifier must be set to a reasonable
listening level.
Back panel of TV
Amplifier
LINE IN
L
R
Connecting an A/V amplifier with built-in digital surround
This connection allows you to use an audio amplifier with built-in
digital surround and external speakers.
You will need:
• one coaxial digital cable
• Six sets of speaker cables
See “Selecting the digital output format” on page 39.
Note:
Refer to the Owner’s manual of the audio
amplifier as well.
Back panel of TV
Front
Speaker
(Right)
Subwoofer
TV
Front
Speaker
(Left)
Center Speaker
Surround
Speaker (Right)
Surround Speaker
(Left)
AV Amplifier with built-in digital surround
The COAXIAL DIGITAL AUDIO OUT jack outputs digital audio only during digital broadcasts with digital audio.To hear analog
broadcast audio, you also must connect analog audio cables from the L/R ANALOG AUDIO jacks to the receiver’s inputs.
Consult the owner’s manual for your receiver to determine the best way to switch between the analog and digital signals.
14
J3W60321A_En_p07-14
14
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the remote control
Preparing the remote control for use
In addition to operating the TV, the remote control can operate most
cable TV converters, satellite receivers, VCRs, and DVD players,
regardless of their brand. The remote control is pre-programmed to
operate most Toshiba satellite receivers, VCRs, and DVD players. To
control a non-Toshiba device (or a Toshiba device that the remote
control is not pre-programmed to operate), you must first program the
remote control. See “Programming the remote control to operate your
other devices” on the next page.
Note:
The TV remote control may not operate your
VCR, DVD player, or cable TV converter.
Refer to the owner's manual supplied with
your other devices to see which features may
be available. Additionally, the remote control
for this TV may not support certain features
available on the original remote controls for
your other devices, in which case it is
suggested that you use the original remote
control for the applicable device.
Installing the remote control batteries
To install the batteries:
1. Open the battery cover on the back of the remote control.
Caution:
• Never throw batteries into a fire.
Note:
• Be sure to use “AAA” size batteries.
• Dispose of batteries in a designated
disposal area.
• Batteries should always be disposed of with
the environment in mind. Always dispose of
batteries in accordance with applicable
laws and regulations.
2. Install two “AAA” size batteries. Match the + and – signs on the
batteries to the signs on the battery compartment.
• If the remote control does not operate
correctly, or if the operating range becomes
reduced, replace batteries with new ones.
• Always remove the batteries from the
remote control if they are dead or if the
remote control is not to be used for an
extended period of time. This will prevent
battery acid from leaking into the battery
compartment.
3. Close the battery cover on the remote control until the lock snaps.
Using the remote control to operate your other devices
To control a cable TV
converter/satellite
receiver:
To control a VCR:
Power
Input (TV)
Mute (TV)
Channel
Numbers
Input (TV)
Power
Channel
Numbers
Program the remote
control to recognize
the brand of your VCR
(see “Programming the
remote control to
operate your other
devices” on the next
page). The buttons
shown at right will then
control the VCR.
Program the remote
control to recognize the
brand of your cable TV
converter/satellite receiver
(see “Programming the
remote control to operate
your other devices” on the
next page). The buttons
shown at right will control
the cable TV converter/
satellite receiver.
CH RTN
(Channel Return)
VCR
Channel M/?
Volume +/– (TV)
CH RTN
(Channel Return)
Channel M/?
CBL/SAT
Volume +/– (TV)
Pic Size (TV)
Pic Size (TV)
Press “VCR” first.
VCR controls
Press “CBL/SAT” first.
TV/VCR
15
J3W60321A_En_p15-22
15
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
To control a DVD player:
Power
Input (TV)
Recall
Mute (TV)
Number
buttons
Program the remote
control to recognize the
brand of your DVD
player (see
“Programming the
remote control to
operate your other
devices” below). The
buttons shown at right
will then control the
DVD player.
Volume +/– (TV)
DVD
Pic Size (TV)
DVD MENU
▲▼
ENTER
DVD controls
Press “DVD” first.
DVD Skip/Search
/
TOP Menu
DVD Clear
Programming the remote control to operate
your other devices
Power
Recall
This remote control is pre-programmed to operate most Toshiba
satellite receivers, VCRs, and DVD players. To control a non-Toshiba
device (or a Toshiba device that the remote control is not pre-
programmed to operate), you must follow the steps below to program
your remote control.
Channel
Numbers
TV
VCR
DVD
1. Refer to the device code tables (on pages 17 and 18) to find the
corresponding code for your device.
CBL/SAT
If more than one code is listed, try each one separately until you
find the one that works.
2. If you are programming the remote control to operate your:
• Cable TV converter/satellite receiver: Press “CBL/SAT.”
• VCR: Press “VCR.”
• DVD player: Press “DVD.”
3. While holding down RECALL, press the Channel Number buttons
to enter the three-digit code for your device within 10 seconds.
Note:If you do not enter the code within 10 seconds from step 3,
or if you enter the wrong code, this operation is canceled.
4. Point the remote control at the device and press POWER to test
the code.
• If the device responds, you entered the correct code.
• If the device does not respond, repeat steps 1–4 using another
code.
Note:
• When shipped from the factory, the remote
control is set to operate your TV.
5. Press “TV” to control the TV.
• Each time you replace the batteries, you
must reprogram the remote control.
• Some newer VCRs are capable of working
on either of two remote codes. These VCRs
have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch and
does not respond to any of the codes for
your VCR, set the switch to the other
position (VCR1 or VCR2) and reprogram
the remote control.
For future reference, write down the codes you used:
Cable TV converter/satellite receiver code _____________________
VCR code ______________________________________________
DVD player code _________________________________________
16
J3W60321A_En_p15-22
16
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Device code tables
[For CBL/SAT mode]
CABLE Box
Brand
Code
Brand
Code
Brand
Code
Satellite
Brand
Code
Brand
Code
Brand
Code
[For VCR mode]
VCR
Brand
Code
Brand
Code
Brand
Code
17
J3W60321A_En_p15-22
17
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
[For VCR mode]
VCR (continued)
Brand
Code
Brand
Code
Brand
Code
TV/VCR Combo
Brand
Code
Brand
Brand
Code
Code
Brand
Brand
Code
Code
[For DVD mode]
DVD
Brand
Code
Portable DVD
Brand
Code
Code
Brand
Brand
Code
Code
Brand
Brand
Code
Code
HTIB
Brand
[For VCR and DVD mode]
DVD/VCR Combo
Brand
VCR Code
DVD Code
Brand
VCR Code
DVD Code
18
J3W60321A_En_p15-22
18
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Learning about the remote control
TV/VIDEO selects the video input source (page 28)
RECALL displays TV status information on-screen (page 40)
MUTE turns off the sound (page 37)
POWER turns the TV on and off
CHANNEL NUMBERS allow direct access to channels (page 22)
TV/Video
Recall
POWER
Mute
CH RTN (Channel Return) returns to the last viewed channel
(page 22)
Channel
Numbers
TV selects TV mode
CH RTN
CBL/SAT selects CBL/SAT mode (page 15)
CH M/? cycles through programmed channels (page 21)
VOL +/– adjusts the volume level
(channel Return)
Channel M/?
Volume +/–
TV
VCR
CBL/SAT
Sleep
DVD
VCR selects VCR mode (page 15)
Picture Size
DVD selects DVD mode (page 16)
FAV ▲/▼
(Favorite Channels)
Menu/Enter
SLEEP programs the TV to turn off at a set time (page 36)
DVD Menu
PIC SIZE cycles through the five picture sizes: Natural,
Enter
Exit
Play
Stop
TheaterWide 1, TheaterWide 2, TheaterWide 3, and Full (page 30)
Pause
Skip/Search
MENU/ENTER accesses the menu system; also sets menu
selections (page 20)
4 ¢
Rew
FF
▲▼
selects or adjusts on-screen menus (page 20)
TOP Menu
TV/VCR
Clear
Rec
FAV ▲/▼ (Favorite Channels) cycles through the channels you
programmed as favorite channels (page 22)
EXIT closes on-screen menus (page 20)
DVD MENU accesses the DVD menu
ENTER sets menu selections in DVD mode
PAUSE pauses a videotape/DVD
PLAY plays a videotape/DVD
Remote control effective range
• Aim the remote control at the TV’s
remote sensor (see illustration) and
press the buttons to operate.
STOP stops a videotape/DVD
SKIP/SEARCH
skips DVD chapter
• Operate the remote control within a 30
degree angle on either side of the remote
sensor, up to a distance of approx. 16 ft.
(5m).
REW rewinds/reverses a videotape/DVD
FF fast forwards a videotape/DVD
TOP MENU accesses the DVD TOP menu
REC starts recording a videotape
Remote
Sensor
CLEAR clears input data in DVD mode
Approx. 5 meters
TV/VCR toggles between TV and VCR modes when viewing
while recording
19
J3W60321A_En_p15-22
19
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
After you have installed the batteries and programmed the remote
control, you need to set some preferences on the TV using the menu
system.You can access the menu system with the buttons on the
remote control.
• When you make a menu selection, your changes are immediate.
You do not have to press MENU or EXIT to save your changes.
• After 15 seconds, the menu screen will automatically close if you
do not make a selection. Your changes will still be saved.
• When you are finished programming the menus, press EXIT.
Starting setup
The STARTING SETUP feature appears the first time you turn on the
TV, and helps you select the menu language, specify the TV/CABLE
setting, and program channels automatically.
POWER
IMPORTANT:You must connect an antenna or cable TV system
first. See “Connecting your TV” on pages 7-14 for details.
1. Press POWER to turn on the TV.
The starting setup function begins
and the language setup menu
appears on the screen. Press ▲ or
▼ to select your desired language,
Menu/Enter
then press ENTER.
2. Press ▲ or ▼ to select “TV” or
“CABLE,” then press ENTER.
3. Press ▲ or ▼ to select START, and then press ENTER, which
starts the AUTO SETUP.
Exit
Note:To cancel the setup and return to the regular TV screen,
press ▲ or ▼ to select CANCEL and press ENTER.
4. When the AUTO SETUP is complete, the regular TV screen
appears.
Note:
• AUTO SETUP of channels may take 15–30 minutes to complete,
depending on your regional cable service.
• To cancel the AUTO SETUP and return to the regular TV screen,
press EXIT.
Changing the on-screen display language
You can choose from three different languages (English, French, and
Spanish) for the on-screen display of adjustment menus and messages.
To select a language:
1. Press MENU, then press or until the SETUP menu appears.
SETUP
LANGUAGE
CLOCK SET
ENGLISH
CABLE
Note:
TV
CH PROGRAM
ADD ERASE
/
CABLE
The position and size of the on-screen menus
may change for some program formats (such
as 1080i or 720p).
/
:SELECT
:ADJUST
2. Press ▲ or ▼ to highlight LANGUAGE.
ENGLISH
CABLE
:SELECT
:ADJUST
3. Press or to highlight your desired language.
20
J3W60321A_En_p15-22
20
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Image tilt correction
When you install or change the direction of the TV, the picture may
become tilted (caused by the Earth’s magnetism). If this happens, use
the image tilt correction feature to obtain the best possible picture.
To adjust the image tilt:
1. Press MENU, then press or
Channel
Numbers
SETUP
until the SETUP menu appears.
2. Press ▲ or ▼ to highlight IMAGE
TILT.
IMAGE TILT
SIGNAL METER
0
3. Press or to adjust the picture
tilt (from –10 to 10).
:SELECT
:ADJUST
Channel M/?
Adding channels to the TV’s memory
When you press CHANNEL ▲/▼ on the TV or CH M/? on the remote
control, your TV will stop only on the channels you have programmed
into the TV’s channel memory. Follow the steps below to program
channels into the channel memory.
Menu/Enter
Exit
Programming channels automatically
Your TV can automatically detect all active channels and store them in
its memory. After the TV has stored the channels in its memory auto-
matically, you can add or erase channels manually.
To add channels automatically:
1. Press MENU, then press or to
display the SETUP menu.
SETUP
2. Press ▲ or ▼ until the TV/CABLE
LANGUAGE
ENGLISH
TV CABLE
CLOCK SET
selection is highlighted.
TV
CH PROGRAM
ADD ERASE
/
CABLE
/
/
3. Press or to highlight either TV or
CABLE, depending on which you
use. If you use an antenna, choose
TV. If you use cable, choose CABLE.
:SELECT
:ADJUST
4. Press ▼ until the CH PROGRAM selection is highlighted.
5. Press or to start channel programming. The TV will automatically
cycle through all the TV or Cable channels (depending on which you
selected), and store all active channels in the channel memory.
While the TV is cycling through the channels, the message
“PROGRAMMING NOW–PLEASE WAIT” appears.
6. When channel programming is complete, the message “COMPLETED”
appears.
Note:
You can add the channel manually (see
“Adding and erasing channels manually,”
below).
7. Press CH M or ? to view the programmed channels.
Adding and erasing channels manually
After you have programmed the channels automatically, you can add or
erase specific channels manually.
To add or erase channels manually:
1. Press MENU, then press or to dis-
play the SETUP menu.
SETUP
2. Press ▲ or ▼ until the ADD/ERASE
LANGUAGE
CLOCK SET
ENGLISH
CABLE
selection is highlighted.
TV
CH PROGRAM
ADD ERASE
/
CABLE
/
3. Press
or
to display the ADD/
ERASE menu.
:SELECT
:ADJUST
4. Press ▲ or ▼ to select ADD/ERASE,
then press
.
5. Press ▲ or ▼ to select the desired channel to be added or erased.
Press or to select ADD or ERASE, whichever function you want
to perform.
6. Repeat step 5 for other channels you want to add or delete, then
press ENTER.
7. Press EXIT to return to the normal screen.
To add a digital channel you are watching:
Select a channel you want to add. Press ▲ or ▼ to select ADDING
CHANNEL in step 4 above, then press
.
To erase all channels from the channel memory:
Press ▲ or ▼ to select CLEAR ALL in step 4 above, then press
.
All channels are erased from the channel memory. (You can still use the
Channel Numbers on the remote control to tune a channel.)
21
J3W60321A_En_p15-22
21
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing channels
To change to the next programmed channel:
Press CHANNEL ▲/▼ on the TV or CH M/? on the remote control.
Note:
To change to a specific analog channel:
Digital cable channels may be represented by
channel numbers that include a “dash” (e.g.,
85–002). These digital channel numbers may
not match the numbers in the channel line-up
provided by your cable company. This is not a
malfunction.
Press the Channel Number buttons (0-9) on the remote control.
For example, to select channel 125, press 1, 2, 5.
To change to a specific digital channel:
Press the first 3 digits, then press the dash key (100/–), followed by the
remaining 3 digits.
For example, to select channel 015-001, press 0, 1, 5, Dash, 0, 0, 1.
Using the TV’s features
Adjusting the channel settings
Channel
Numbers
Switching between two channels
You can switch between two channels without entering an actual
channel number each time.
CH RTN
Dash (100/–)
To switch between two channels:
Channel M/?
1. Select the first channel you want to view.
2. Select a second channel using the Channel Number buttons (0-9,
100).
Menu/
Enter
3. Press CH RTN. The previous channel will be displayed.
Each time you press CH RTN, the TV will switch back and forth
between the two channels. The CH RTN feature is available for the
video input sources also.
FAV ▲/ ▼
Exit
Programming your favorite channels
You can preset up to 12 of your favorite channels using the Favorite
Channel Programming feature. Because this feature scans through
only your favorite channels, it allows you to skip other channels you
do not normally watch.
You can still use Channel M/? to scan through all the channels you
programmed in the TV’s memory.
To program your favorite channels:
1. Select a channel you want to program as a favorite channel.
2. Press MENU, then press or to display the OPTION menu.
3. Press ▲ or ▼ to highlight FAVORITE CH.
4. Press or to display the
FAVORITE CH menu. SET/CLEAR
will be highlighted.
5. Press or to highlight SET and
press ENTER.
Note:
To return to the OPTION menu from the
FAVORITE CH menu, press ▲ or ▼ to
highlight OPTION MENU, then press or
.
6. Press EXIT to return to normal
viewing.
7. Repeat steps 1-6 for up to 12
channels.
To select your favorite channels:
Press the FAV ▲/▼ buttons on the remote control to select your
favorite channels.
The FAV ▲/▼ buttons will not work until you have programmed
one or more favorite channels.
22
J3W60321A_En_p15-22
22
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
To clear your favorite channels:
1. Select a channel you want to clear from the favorite channel memory.
2. Press MENU, then press or to display the OPTION menu.
3. Press ▲ or ▼ to highlight FAVORITE CH.
4. Press or to display the FAVORITE CH menu. SET/CLEAR
will be highlighted.
Channel
Numbers
5. Press or to highlight CLEAR.
Channel M/?
Menu/
Enter
6. Press ENTER until “0” replaces the channel number you want to
erase.
7. Press EXIT to return to normal viewing.
8. Repeat steps 1-7 for the other channels.
Exit
Using the LOCKS menu
Note: The V-Chip feature is available for the U.S. V-Chip system
only. The Canadian V-Chip system is not supported.
You can prevent others from viewing certain programs or channels by
blocking them using the V-Chip feature.
Selecting a password
Before you can use the V-Chip feature to block programs and
channels, you must select a password. The password you select
prevents others from changing the rating limits you set.
To select your password and access the LOCKS menu:
1. Press MENU, then press or to highlight the LOCKS menu.
2. Press ▲ or ▼ to display the password entering mode.
3. Use the Channel Number buttons (0-9) to enter your password.
If you are accessing the LOCKS menu for the first time, select a
four-digit number to be your password. Press ENTER.
4. Enter the password again to confirm it, and then press ENTER.
The LOCKS menu appears.
23
J3W60321A_En_p23-29
23
27/2/06, 9:54 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
5. You may now set up the LOCKS menu. See “Using the V-Chip
(parental control) feature” (below), “Locking channels” (page 25),
“Locking the video inputs” (page 26), “Setting the GameTimerTM”
(page 26) or “Using the front panel lock feature” (page 27).
Recall
Channel
Numbers
To change your password:
1. Press MENU, then press or to display the LOCKS menu.
2. Press ▲ or ▼ to display the password entering mode.
3. Use the Channel Number buttons (0-9) to enter your password.
Press ENTER. The LOCKS menu appears.
4. Press ▲ or ▼ to highlight NEW PASSWORD and press or to
display the NEW PASSWORD menu.
Menu/
Enter
5. Use the Channel Number buttons (0-9) to enter a new code. Press
ENTER.
6. Enter the password again to confirm it, and then press ENTER.
7. Press EXIT to return to normal viewing.
Exit
Using the V-Chip (parental control) feature
The Motion Picture Association of America (MPAA) uses a rating
system to qualify motion picture content. Television broadcasters also
employ a rating system to qualify the content of television programs.
The TV and MOVIE ratings work with the V-Chip feature and allow you
to block programs according to the rating limits you set.
To use the V-Chip to block programs by rating:
1. Press MENU, then press or to display the LOCKS menu.
2. Press ▲ or ▼ to display the password entering mode.
3. Use the Channel Number buttons (0-9) to enter your password.
Press ENTER. The LOCKS menu appears.
4. Press ▲ or ▼ to highlight V-CHIP.
• Press or to highlight ON to
enable V-Chip program blocking by
LOCKS
V-CHIP
V-CHIP SET
V-CHIP SET (DTV)
ON
/
OFF
rating.
Note:
• Press or to highlight OFF to
disable V-Chip program blocking by
rating.
:SELECT
:ADJUST
• If you forget your password, press RECALL
four times within five seconds while the TV
is in password entering mode. This allows
you to reset your password.
• You can use V-CHIP SET (DTV) function
when the digital broadcasting with a new
rating system is received on the TV.
5. Press ▲ or ▼ to highlight V-CHIP
SET. Then, press or to display
the V-CHIP SET menu.
6. Press ▲ or ▼ to highlight TV RATING.
Then, press or to display the
desired rating.
LOCKS
V-CHIP
V-CHIP SET
V-CHIP SET (DTV)
ON
:SELECT
:ADJUST
OFF
: TV RATING is not set
TV-Y
: All children
V-CHIP SET
TV-Y7 : 7 years old and above
TV-G : General audience
TV RATING
OFF
OFF
TV-Y TV-Y7
TV-14 TV-MA
/
/
/
TV-G
TV-PG
/
/
MOVIE RATING
TV-PG : Parental guidance
TV-14 : 14 years old and above
TV-MA : 17 years old and above
:SELECT
:ADJUST
• When you select TV-Y7, TV-PG, TV-14, or TV-MA, press RECALL to
explain the rating. Press ▲ or ▼ to select the desired rating you
want. Press or to select the setting ON or OFF.
7. Press ▲ or ▼ to highlight MOVIE RATING. Then, press or to
display the RATING SET menu. Press ▲ or ▼ to select the
desired rating, then press or to select ON or OFF.
G
PG
: All ages
: Parental guidance
RATING SET
G
PG
:
:
:
:
:
:
ON /OFF
ON
ON
PG-13 : Parental guidance less than
PG-13
R
ON
13 years old
NC-17
X
ON
ON
R
: Under 17 years old Parental
guidance suggested
:SELECT
:ADJUST
NC17 : 17 years old and above
X
: Adult only
24
J3W60321A_En_p23-29
24
27/2/06, 9:55 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
7. When you are done selecting the ratings, press EXIT to return to
normal viewing.
When you try to view a program with a ratings block, a message will
appear listing the program’s ratings. The program can still be viewed if
you press MUTE and then enter your password to temporarily bypass
the block.
Locking channels
With the CH LOCK feature, you can lock specific channels.You will not
be able to tune locked channels unless you clear the setting.You can
choose to lock up to 12 TV channels and 12 cable channels.
Mute
To lock channels:
1. Select a channel you want to lock.
Channel
Numbers
2. Press MENU, then press or to display the LOCKS menu.
3. Press ▲ or ▼ to display the password entering mode.
4. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS
Channel M/?
Menu/
Enter
menu appears.
5. Press ▲ or ▼ to highlight CH
LOCKS
LOCK and press or to display
the CH LOCK menu.
6. Press or to select the follow-
ing:
LOCK
CH LOCK
VIDEO LOCK
OFF
OFF
OFF
GAME TIMER
FRONT PANEL LOCK
NEW PASSWORD
:SELECT
:ADJUST
Exit
• SET, to set the channel as one to
be locked. Then press ENTER.
7. Repeat steps 1 through 6 to lock
other channels. When you are
finished locking channels, press
EXIT to return to normal viewing.
If you try to tune a locked channel, the
TV will not display it, but will display the nearest unlocked channel.
To unlock channels:
1. Press MENU, then press or to display the LOCKS menu.
2. Press ▲ or ▼ to display the password entering mode.
3. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS menu appears.
4. Press ▲ or ▼ to highlight CH LOCK and press or to display
the CH LOCK menu.
Note:
• After programming CH LOCK, change
channels before turning off the television.
• To return to the LOCKS menu from the
CH LOCK menu, press ▲ or ▼ to highlight
5. Press or to highlight CLEAR and clear all channels from the
list of locked channels. Press ENTER.
LOCKS MENU, then press or
.
6. Press EXIT to return to normal viewing.
25
J3W60321A_En_p23-29
25
27/2/06, 9:55 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Locking the video inputs
With the VIDEO LOCK feature, you can lock out the input sources
(VIDEO-1, VIDEO-2, VIDEO-3, ColorStream HD-1, ColorStream HD-2,
HDMI) and channels 3 and 4.
Recall
TV/Video
You will not be able to select the input sources with the TV/VIDEO
button or Channel Number buttons unless you unlock the video inputs.
Channel
Numbers
To set up the video lock:
1. Press MENU, then press or to display the LOCKS menu.
2. Press ▲ or ▼ to display the password entering mode.
3. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS menu appears.
4. Press ▲ or ▼ to highlight VIDEO LOCK.
Menu/
Enter
5. Press or to select one of the following:
•
VIDEO: Locks VIDEO-1, VIDEO-
2, VIDEO-3, ColorStream HD-1,
ColorStream HD-2, and HDMI
.
LOCKS
• VIDEO +: Locks VIDEO-1,
Exit
LOCK
CH LOCK
VIDEO LOCK
OFF
VIDEO
OFF
VIDEO-2, VIDEO-3, ColorStream
HD-1, ColorStream HD-2, HDMI,
channel 3, and channel 4. This
option should be used if you use
OFF
/
/
VIDEO+
GAME TIMER
OFF
FRONT PANEL LOCK
NEW PASSWORD
:SELECT
:ADJUST
the antenna terminal to play a video tape.
6. Press EXIT to return to normal viewing.
To unlock the video inputs:
Note:
Select OFF in step 5, above which unlocks all video input sources
After programming VIDEO LOCK, change
channels or press TV/VIDEO before turning
off the TV or it will be locked the next time it is
turned on.
and channels 3 and 4.
Setting the GameTimerTM
With the GameTimerTM feature, you can automatically activate the
VIDEO LOCK feature (VIDEO setting) to set a time limit for playing a
video game (30, 60, 90, or 120 minutes).
To set up the GameTimer:
1. Press MENU, then press or to display the LOCKS menu.
2. Press ▲ or ▼ to display the password entering mode.
3. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS menu appears.
4. Press ▲ or ▼ to highlight GAME TIMER.
5. Press or to select a time limit (30 minutes, 60 minutes, 90
minutes, 120 minutes, or OFF).
6. Press EXIT to return to normal viewing. After the GameTimer is
programmed, the display will appear briefly every ten minutes to
remind you that the GameTimeris
Note:
• You can enjoy playing video games on this
TV; however, certain video games that
utilize so-called “light gun” joysticks for
shooting at on-screen targets may not work
with this TV.
• To display the GameTimer setting, press
RECALL (see “Displaying TV status
information on-screen” on page 40).
operating.
When the programmed time is
reached, the TV will change
channels automatically and enter
VIDEO LOCK mode.
LOCKS
LOCK
CH LOCK
VIDEO LOCK
GAME TIMER
OFF
OFF
OFF
/
30
/
60
/
90
/
120
OFF
FRONT PANEL LOCK
NEW PASSWORD
:SELECT
:ADJUST
To deactivate the GameTimer and unlock the VIDEO LOCK:
Set the VIDEO LOCK to OFF (see “Locking the video inputs” above).
26
J3W60321A_En_p23-29
26
27/2/06, 9:55 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
TV front panel
Using the front panel lock feature
You can lock the front panel buttons to prevent your settings from being
changed accidentally (by children, for example). When the front panel
lock is in ON, all control buttons on the TV front panel (except POWER)
do not operate.
To lock the front panel:
1. Press MENU, then press or to display the LOCKS menu.
2. Press ▲ or ▼ to display the password entering mode.
3. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS
Buttons to be locked
TV front panel
menu appears.
4. Press ▲ or ▼ to highlight FRONT
LOCKS
PANEL LOCK and press or to
highlight ON.
LOCK
CH LOCK
VIDEO LOCK
OFF
OFF
GAME TIMER
5. Press EXIT to return to normal
viewing.
ON
/
OFF
FRONT PANEL LOCK
NEW PASSWORD
:SELECT
VOLUME
Recall
:ADJUST
If a button on the front panel (other
than POWER) is pressed, the message “NOT AVAILABLE” appears.
To unlock the front panel:
Press and hold the VOLUME ▼ button on the TV front panel for
about 10 seconds until the message “FRONT PANEL LOCK:OFF”
appears on-screen.
Channel
Numbers
To unlock the front panel using the menus:
Select OFF in step 4, above.
Channel M/?
Labeling channels
Menu/
Enter
Channel labels appear above the on-screen channel number display
each time you turn on the TV, select a channel, or press the RECALL
button.You can choose any four characters to create a channel label.
To create channel labels:
1. Select a channel you want to label.
2. Press MENU, then press or
until the OPTION menu appears.
3. Press ▲ or ▼ to highlight CH
LABEL.
Exit
OPTION
ON/OFF TIMER
FAVORITE CH
CH LABEL
OFF
VIDEO LABEL
:SELECT
:ADJUST
4. Press or to display the CH
LABEL menu. SET/CLEAR will be
highlighted.
5. Press or to highlight SET.
6. Press ENTER to highlight LABEL.
7. Repeatedly press or until the
character you want appears. Press
ENTER.
CH LABEL
:CH 25
SET
/
CLEAR
LABEL
–
–
–
–
OPTION MENU
:SELECT
ENTER:SET
:ADJUST
EXIT:END
To erase channel labels:
1. Tune the TV to the channel whose label
Note: The character will change as follows:
you want to erase.
2. Press MENU, then press or until the
OPTION menu appears.
3. Press ▲ or ▼ to highlight CH LABEL.
4. Press or to display the CH LABEL
menu. SET/CLEAR will be highlighted.
5. Press or to highlight CLEAR.
6. Press ENTER.
8. Repeat step 7 to enter the rest of
the characters.
CH LABEL
SET
LABEL
:CH 25
If you would like a blank space in
the label name, you must choose
an empty space from the list of
characters; otherwise, a dash will
appear in that space.
–
–
–
–
OPTION MENU
:ADJUST
ENTER:SET
EXIT:END
7. Repeat steps 1-6 to erase other channel
labels.
9. Repeat steps 1-8 for other channels.You can assign a label to
each channel.
Note:
10. Press EXIT to return to normal viewing.
To return to the OPTION menu from the CH
LABEL menu, press ▲ or ▼ to highlight
OPTION MENU, then press or
.
27
J3W60321A_En_p23-29
27
27/2/06, 9:55 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the video input source
Press TV/VIDEO to view a signal from another device connected to
your TV, such as a VCR or DVD player. You can select ANT, VIDEO1,
VIDEO2, VIDEO3, ColorStream HD1, ColorStream HD2, or HDMI,
depending on which input jacks you used to connect your devices
(see “Connecting your TV” on pages 7-14).
NEVER CONNECT THIS TV TO A
PERSONAL COMPUTER (PC).
This TV is not intended for use
with a PC.
SOURCE SELECTION
0. ANT
1. VIDEO1
2. VIDEO2
3. VIDEO3
4. ColorStream HD1
5. ColorStream HD2
6. HDMI
/0-6:SELECT
Pressing TV/VIDEO on the
remote control displays the
current signal source. (Press TV/
VIDEO again, ▲/▼, or 0-6 to
change the source.)
Labeling the video input sources
The video label feature allows you to label each input source for your
TV from the following preset list of labels:
TV/Video
0-6
–
: Uses the default label name
VCR : Video cassette recorder
DVD : DVD video
DTV : Digital TV set-top box
SAT
: Satellite box
CBL : Cable box
Menu
Exit
HD
: HDMI device (HDMI only)
To label the video input sources:
1. Press MENU, and then press or
to display the OPTION menu.
2. Press ▲ or ▼ to highlight VIDEO
LABEL.
3. Press to display the VIDEO
LABEL menu.
4. Press ▲ or ▼ to highlight the video
source you want to label.
5. Press or to select the desired
label for that input source.
6. Press EXIT to return to normal
viewing.
VIDEO LABEL
1.VIDEO1
2.VIDEO2
3.VIDEO3
4.ColorStream HD1
5.ColorStream HD2
6.HDMI
-
-
-
-
-
-
/
VCR
/
DVD
SAT
/
/
DTV
CBL
OPTION MENU
:SELECT
:ADJUST
28
J3W60321B_En_p23-29
28
3/4/06, 6:10 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the clock
Note:
You must set the clock before you can program the ON/OFF timer.
After a power failure or disconnection of the
power, the clock settings will be lost.
To set the clock: (Example: “8:30 AM” March, 25 (SAT), 2006)
1. Press MENU, then press or to
display the SETUP menu.
2. Press ▲ or ▼ to highlight CLOCK
SET, then press
.
3. Press or to set the MONTH,
then press ▼.
Recall
4. Set the DAY, YEAR and TIME as in
step 3.
After setting the clock, the date and
time function starts automatically.
5. Press EXIT to return to normal
viewing.
Menu/
Enter
Setting the ON/OFF timer
This feature allows you to program the TV to turn on or off automati-
cally at a set time. If you program the ON TIMER to “DAILY,” the TV will
turn on every day at the same time to the same channel until you clear
the ON TIMER.
Exit
To set the ON timer: (Example:Turning on the TV to channel 2 at
6:30 AM, DAILY)
1. Set the clock, if you have not already done so (see above).
2. Press MENU, and then press or to display the OPTION menu.
3. Press ▲ or ▼ to highlight ON/OFF TIMER.
4. Press or to highlight SET, then press ENTER. The ON/OFF
TIMER menu appears.
5. Press ▲ or ▼ to highlight ON TIMER,
then press to highlight the hour
position.
ON/OFF TIMER
ON TIMER
6:00AM
CH 2
CLEAR
6. Press ▲ or ▼ to set the desired hour,
then press
7. Set the desired minutes and channel,
as in step 6.
OFF TIMER
12:00AM
CLEAR
.
OPTION MENU
:SELECT
:ADJUST
EXIT:END
8. Press or to select ONCE or
DAILY, then press ENTER.
9. Press EXIT to return to normal
viewing.
ON/OFF TIMER
Note:
ON TIMER
6:30AM
CH
ONCE DAILY CLEAR
2
• After a power failure or disconnection of
the power, the ON/OFF timer settings will
be lost.
OFF TIMER
12:00AM
CLEAR
OPTION MENU
:ADJUST
ENTER:SET
EXIT:END
• To display the ON/OFF timer settings,
press RECALL (see “Displaying TV status
information on-screen” on page 40).
• To return to the OPTION menu from the
ON/OFF TIMER menu, press ▲ or ▼ to
highlight OPTION MENU, then press
To set the OFF timer:
Follow steps 1-9 above, except select
OFF TIMER in step 5.
ON/OFF TIMER
ON TIMER
6:30AM
CH
DAILY
2
OFF TIMER
12:00AM
CLEAR
OPTION MENU
:SELECT
or
.
:ADJUST
EXIT:END
To cancel the ON/OFF timers:
Press twice to select CLEAR in step 4, above.
Press EXIT to return to normal viewing.
29
J3W60321A_En_p23-29
29
27/2/06, 9:55 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing the wide-screen picture formats
(480i and 480p signals only)
You can view 480i and 480p format programs in a variety of
picture sizes—Natural, TheaterWide 1, TheaterWide 2, TheaterWide 3,
and Full.
0-4
The way the image displays in any of the picture sizes will vary
depending on the format of the program you are viewing. Select the
picture size that displays the current program the way that looks best
to you.
Selecting the picture size
1. Press PIC SIZE on the remote control.
Pic Size
2. Press the corresponding number button (0-4) or ▲/▼ to select the
desired picture size, as described below and on the next page.
▲/▼
PICTURE SIZE
0. NATURAL
1. THEATER WIDE1
2. THEATER WIDE2
3. THEATER WIDE3
4. FULL
Note:
You also can change the picture size by
selecting PICTURE SIZE in the SETUP
menu.
/0-4:SELECT
SETUP
Natural picture size
CLOSED CAPTION
OFF
•
The image is displayed close to its originally formatted proportion.
Some program formats will display with side bars and/or bars at the
top and bottom.
CC ADVANCED
PICTURE SIZE
PICTURE SCROLL
CINEMA MODE
FILM
:SELECT
:ADJUST
Natural picture size example: The way the image displays will vary
depending on the format of the program you are currently watching.
Note:
The PICTURE SIZE feature is not available
for some program formats (such as 1080i or
720p). Such formats will display in Natural
picture size.
Conventional (4:3) picture in
Natural size on your wide-screen
TV
Conventional (4:3) picture
on a conventional TV
screen
NOTICE OF POSSIBLE ADVERSE
EFFECTS ON TV PICTURE DISPLAY
Avoid displaying stationary images on your
TV screen for extended periods of time.
Fixed (non-moving) patterns or images
(including but not limited to PIP/POP
windows, closed captions, video game
patterns, TV station logos, stock tickers,
websites, and special formats that do not
use the entire screen) can become
permanently ingrained in the cathode ray
tube(s) of the TV and cause subtle but
permanent ghost images. This type of
damage is NOT COVERED BYYOUR
WARRANTY.
TheaterWide 1 picture size (for 4:3 format programs)
•
The picture is stretched wider to fill
the width of the screen, but only
slightly stretched taller.
The top and bottom edges of the
picture may be hidden; however,
this mode cannot be scrolled.
•
Using these functions to change the
picture size (i.e., changing the height/ width
ratio) for any purpose other than your
private viewing may be prohibited under
the Copyright Laws of the United States
and other countries, and may subject you
to civil and criminal liability.
TheaterWide 1 picture size
example
30
J3W60321A_En_p30-37
30
27/2/06, 9:55 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
TheaterWide 2 picture size (for letter box programs)
Note:
•
The picture is stretched the same
amount both wider and taller
If you select TheaterWide 2 or 3, the top
and bottom edges of the picture may be
hidden. To see the hidden edges, either
scroll the picture (see page 32) or try
viewing the program in Full picture size.
(retains its original proportion).
The top and bottom edges of the
picture may be hidden. To view the
hidden areas, see “Scrolling the
TheaterWide picture” on page 32.
•
A B C D E F G - - - - - - - - - - - - - - - -
TheaterWide 2 picture size
example
TheaterWide 3 picture size (for letter box programs
with subtitles)
•
The picture is stretched wider to fill
the width of the screen, but only
slightly stretched taller.
A B C D E F G - - - - - - - - - - - - - - - -
•
The top and bottom edges of the
picture may be hidden. To view the
hidden areas (such as subtitles or
captions), see “Scrolling the
TheaterWide picture” on page 32.
A B C D E F G - - - - - - - - - - - - - - - - - - - - - - - - - -
TheaterWide 3 picture size
example
Full picture size (for 16:9 source programs)
NOTICE OF POSSIBLE ADVERSE
EFFECTS ON TV PICTURE DISPLAY
Avoid displaying stationary images on your
TV screen for extended periods of time.
Fixed (non-moving) patterns or images
(including but not limited to PIP/POP
windows, closed captions, video game
patterns, TV station logos, stock tickers,
websites, and special formats that do not
use the entire screen) can become
permanently ingrained in the cathode ray
tube(s) of the TV and cause subtle but
permanent ghost images. This type of
damage is NOT COVERED BYYOUR
WARRANTY.
•
If receiving a 16:9 format program,
the picture is displayed in its original
proportion.
If receiving a 4:3 format program,
the picture is stretched wider to fill
the width of the screen, but not
stretched taller.
•
•
None of the picture is hidden.
Full picture size example
Using these functions to change the
picture size (i.e., changing the height/ width
ratio) for any purpose other than your
private viewing may be prohibited under
the Copyright Laws of the United States
and other countries, and may subject you
to civil and criminal liability.
31
J3W60321A_En_p30-37
31
27/2/06, 9:55 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Scrolling the TheaterWide® picture
(TheaterWide 2 and 3 only)
1. Press PIC SIZE to select the TheaterWide 2 or 3 mode.
2. Press MENU, and then press or until the SETUP menu appears.
3. Press ▲ or ▼ to highlight PICTURE SCROLL.
SETUP
CLOSED CAPTION
OFF
CC ADVANCED
PICTURE SIZE
PICTURE SCROLL
CINEMA MODE
FILM
:SELECT
:ADJUST
Pic Size
Menu
4. Press or to display the Scroll Adjustment mode.
SCROLL ADJUSTMENT
TO ADJUST
0
5. Press ▲ or ▼ to adjust the vertical position of the picture.
• Normal (center) position
SCROLL ADJUSTMENT
TO ADJUST
0
• To raise the picture, press ▲.
Note:
You can scroll the picture in TheaterWide 2
and TheaterWide 3 only. The scroll amounts
are as follows:
SCROLL ADJUSTMENT
TO ADJUST
+15
• 480i/480p signal source:
TheaterWide 1 : Not adjustable
TheaterWide 2 : -10 to +20
TheaterWide 3 : -10 to +10
• To lower the picture, press ▼.
SCROLL ADJUSTMENT
TO ADJUST
–10
32
J3W60321A_En_p30-37
32
27/2/06, 9:55 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the cinema mode
When you view a DVD movie (3:2 pulldown processed) from a DVD
player connected to the ColorStream (component video) inputs on the
TV, smoother and more natural motion can be obtained by setting the
CINEMA MODE to FILM.
To set the CINEMA MODE to FILM:
1. Press MENU, and then press or
until the SETUP menu appears.
2. Press ▲ or ▼ to highlight CINEMA
MODE.
3. Press
or to highlight FILM.
4. Press EXIT to return to normal
viewing.
To set the CINEMA MODE to VIDEO (off):
Highlight VIDEO in step 3, above.
Menu
Exit
Selecting the display format
(for 480p signals only)
This feature converts a 480p input signal to 540p or 1080i.
To select the display format:
1. Press MENU, and then press or until the PICTURE menu
appears.
2. Press ▲ or ▼ to highlight DISPLAY FORMAT.
3. Press or to select 540p or 1080i.
Note:
• The DISPLAY FORMAT feature is available
only for 480p input. 1080i is always output
when a signal other than 480p is input.
• If you notice flickering in a 480p image, try
setting the DISPLAY FORMAT to 540p.
Adjusting the picture
Selecting the picture mode
You can select four picture modes—Sports, Standard, Movie, and
Memory—as described in the following table:
Mode
Picture Quality
SPORTS
Bright and dynamic picture (factory-set)
STANDARD Standard picture quality (factory-set)
MOVIE
MEMORY
Movie-like picture setting (factory-set)
Your personal preferences (set by you;
see “Adjusting the picture quality” on page 34 )
To select the picture mode:
1. Press MENU, then press or to display the PICTURE menu.
2. Press ▲ or ▼ to highlight MODE.
3. Press or to highlight the mode you prefer.
4. Press EXIT to return to normal viewing.
33
J3W60321A_En_p30-37
33
27/2/06, 9:55 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the picture quality
You can adjust the picture quality to your personal preferences,
including the brightness, contrast, color, tint, and sharpness. The
qualities you choose will be stored automatically in the PICTURE
menu’s MEMORY mode so you can recall them at any time.
To adjust the picture quality:
1. Press MENU, then press or to display the PICTURE menu.
2. Press ▲ or ▼ until the item you want to adjust is highlighted.
Menu
Exit
3. Press or to adjust the level.
Selection
Pressing
BRIGHTNESS
CONTRAST
COLOR
TINT
SHARPNESS
darker
lower
paler
reddish
softer
lighter
higher
deeper
greenish
sharper
4. Press EXIT to return to normal viewing.
Selecting the color temperature
Change the picture quality by selecting from three preset color tem-
peratures—cool, medium, and warm—as described in the following
table:
Mode
Picture Quality
COOL
MEDIUM
WARM
Blueish
Neutral
Reddish
To select the color temperature:
1. Press MENU, then press or to display the PICTURE menu.
2. Press ▲ or ▼ to highlight COLOR TEMPERATURE.
PICTURE
CableClear
COLOR
ON
COOL
TEMPERATURE
DISPLAY FORMAT
SVM
COOL
/
MEDIUM
/
WARM
1080i 1080i
HIGH
RESET
:SELECT
:ADJUST
3. Press or to highlight the mode you prefer.
4. Press EXIT to return to normal viewing.
34
J3W60321A_En_p30-37
34
27/2/06, 9:55 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Using the CableClear feature
CableClear® reduces visible interference in your TV picture. This
is useful when receiving a broadcast with a weak signal (especially a
Cable channel) or playing a video cassette or disc damaged by
repeated use.
To turn on the CableClear® feature:
1. Press MENU, then press or to display the PICTURE menu.
2. Press ▲ or ▼ to highlight CableClear.
Menu
Exit
3. Press or to highlight ON.
4. Press EXIT to return to normal viewing.
To turn off the CableClear® feature:
Highlight OFF in step 3, above.
Selecting the Scan Velocity Modulation (SVM)
The SVM feature enhances picture contrast and sharpness. This
feature has three modes: HIGH, LOW, and OFF.
To select the SVM feature:
1. Press MENU, then press or to display the PICTURE menu.
2. Press ▲ or ▼ to highlight SVM.
Note:
SVM is not required when viewing some
high-quality video material. If you are
watching high-quality video material, you may
want to set SVM to OFF.
3. Press or to select the mode you prefer.
4. Press EXIT to return to normal viewing.
To turn off the SVM:
Select OFF in step 3.
Resetting your picture adjustments
The RESET function returns your picture quality adjustments to the
following factory settings:
Mode ............................ sports Tint ......................... center (0)
Brightness ............ center (25) Sharpness............ center (25)
Contrast .................. max (50) Color temperature........... cool
Color .................... center (25) SVM ................................ high
To reset your picture adjustments:
1. Press MENU, then press or to display the PICTURE menu.
2. Press ▲ or ▼ to highlight RESET, and then press
.
35
J3W60321A_En_p30-37
35
27/2/06, 9:56 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the sleep timer
You can use the sleep timer to automatically turn off the TV at a set time.
To set the sleep timer:
Repeatedly press SLEEP on the remote control to set the length of
time until the TV turns off.The clock will increase 10 minutes for each
press of the SLEEP button (0h00m, 0h10m, ...1h50m, 2h00m). After
the sleep timer is programmed, the display will appear briefly every
ten minutes to remind you that the sleep timer is operating.
Sleep
To confirm the sleep timer setting:
Press SLEEP one time. The remaining time will be momentarily
displayed.
Menu/Enter
To cancel the sleep timer:
Repeatedly press SLEEP until the display turns to 0h00m.
Using the closed caption feature
The Closed Caption feature has two options:
Exit
•
Captions—An on-screen display of the dialogue, narration, and
sound effects of programs and videos that are closed-captioned
(usually identified as “CC”).
•
Text—An on-screen display of information not related to the program,
such as weather or stock data (if available in your viewing area).
To view captions or text:
1. Tune the TV to the desired program.
2. Press MENU, and then press or
to display the SETUP menu.
3. Press ▲ or ▼ to highlight CLOSED
CAPTION.
4. Press or to select the desired
Closed Caption mode, as follows:
SETUP
CLOSED CAPTION
OFF
C2
C1
/
/
T1
/
T2
/
OFF
Important Note:
CC ADVANCED
PICTURE SIZE
PICTURE SCROLL
CINEMA MODE
If text is not available in your viewing
area, a black rectangle may appear
on-screen. If this happens, set the
Closed Caption feature to OFF.
VIDEO
:ADJUST
:SELECT
• To view captions, select C1 or C2 (C1 displays translation of the
primary language in your area).
Note: If the program or video you selected is not closed-
captioned, no captions will display on-screen.
• To view text, select T1 or T2.
Note:
A closed caption signal may not be decoded
in the following situations:
- when a video tape has been dubbed
- when the signal reception is weak
- when the signal reception is non-standard
Note: When a digital signal is received, you can choose from
CS1, CS2, CS3, CS4, CS5, CS6, C1, C2, C3, C4, T1, T2, T3, T4,
and OFF.
To turn off the Closed Caption feature:
Select OFF in step 4, above.
NOTICE OF POSSIBLE ADVERSE
EFFECTS ON TV PICTURE DISPLAY
Avoid displaying stationary images on
your TV screen for extended periods of
time. Fixed (non-moving) patterns or
images (including but not limited to PIP/
POP windows, closed captions, video
game patterns, TV station logos, stock
tickers, websites, and special formats that
do not use the entire screen) can become
permanently ingrained in the cathode ray
tube(s) of the TV and cause subtle but
permanent ghost images. This type of
damage is NOT COVERED BYYOUR
WARRANTY.
Using the CC advanced feature
This feature is designed to customize digital captions only.
1. Tune the TV to the desired program.
2. Press MENU, and then press or
to display SETUP menu.
3. Press ▲ or ▼ to highlight CC ADVANCED, then press
4. Press ▲ or ▼ to select the desired item to adjust, then press or
5. Press ▲ or ▼ to select the desired setting, then press ENTER.
You can select from among the following items and parameters.
.
.
Items
Parameters
TEXT SIZE:
TEXT TYPE:
AUTO, SMALL, STANDARD, LARGE
AUTO, DEFAULT, MONO W. SERIF, PROP. W.
SERIF, MONO W/O SERIF, PROP. W/O SERIF,
CASUAL, CURSIVE, SMALL CAPITALS
TEXT COLOR:
AUTO, BLACK, WHITE, RED, GREEN, BLUE,
YELLOW, MAGENTA, CYAN
Note:
TEXT EDGE:
AUTO, NONE, RAISED, DEPRESSED,
UNIFORM, LEFT DROP SHADOW, RIGHT
DROP SHADOW
Do not set the Closed Caption “Text Color”
and “Background Color” as the same color or
you will not be able to see the text.
BACKGROUND
COLOR:
AUTO, BLACK, WHITE, RED, GREEN, BLUE,
YELLOW, MAGENTA, CYAN
6. Press EXIT to return to normal viewing.
36
J3W60321A_En_p30-37
36
27/2/06, 9:56 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the sound
Muting the sound
Press MUTE to temporarily turn off the sound. While the sound is off,
the screen will display the word MUTE in the lower right-hand corner.
To restore the sound, either press MUTE again or press VOL +/–.
Selecting stereo/SAP broadcasts
Mute
The multi-channel TV sound (MTS) feature provides high-fidelity stereo
sound. MTS also can transmit a second audio program (SAP) containing
a second language or other audio information (when available).
Note: The MTS feature is not available in DIGITAL and VIDEO mode.
Recall
When the TV receives a stereo or SAP broadcast, the word
“STEREO” or “SAP” displays on-screen every time you turn on
the TV, change the channel, or press RECALL.
Volume
Menu
To listen to stereo sound:
1. Press MENU, then press or to display the AUDIO menu.
2. Press ▲ or ▼ to highlight MTS.
3. Press or to highlight STR (stereo).
Note:
• In general, you can leave your TV in stereo mode because the
TV automatically outputs the type of sound being broadcast
(stereo or mono).
Exit
•
If the stereo sound is noisy, select MONO to reduce the noise.
Note:
A second audio program (SAP) can be heard
only on those TV stations that offer it.
4. Press EXIT to return to normal viewing.
For example, a station might broadcast music
as a second audio program. If you have SAP
on, you will see the current program on the
screen but hear music instead of the
program’s normal audio.
To listen to a second audio program (SAP):
1. Press MENU, then press or to display the AUDIO menu.
2. Press ▲ or ▼ to highlight MTS.
3. Press or to highlight SAP. The TV speakers will output the
second audio program instead of normal audio.
4. Press EXIT to return to normal viewing.
However, if you have SAP on, and the station
you are watching is not currently
broadcasting a second audio program, the
station’s normal audio will be output;
however, occasionally there is no sound at all
in SAP mode. If this happens, set the MTS
feature to STEREO mode.
Adjusting the sound quality
You can change the sound quality of your TV by adjusting the bass,
treble, and balance.
To adjust the sound quality:
1. Press MENU, then press or to display the AUDIO menu.
2. Press ▲ or ▼ to highlight the item you want to adjust.
Note:
3. Press or to adjust the level.
Adjusting the bass, treble, or balance does
not affect the sound quality from the variable
audio OUT jacks.
•
makes the selected quality weaker or increases the balance
in the left channel, depending on the item selected.
makes the selected quality stronger or increases the balance
in the right channel, depending on the item selected.
•
37
J3W60321A_En_p30-37
37
27/2/06, 9:56 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the StableSound® feature
The StableSoundfeature limits the highest volume level to prevent
extreme changes in volume when the signal source is changed.
To turn on the StableSound® feature:
1. Press MENU, then press or to display the AUDIO menu.
2. Press ▲ or ▼ to highlight STABLE SOUND.
3. Press or to highlight ON.
Menu
Exit
4. Press EXIT to return to normal viewing.
To turn off the StableSound® feature:
Highlight OFF in step 3, above.
Turning off the built-in speakers
Use this feature to turn off the TV speakers when you connect an
audio system (see “Connecting an audio system” on page 14).
To turn off the built-in speakers:
1. Press MENU, then press or to display the AUDIO menu.
2. Press ▲ or ▼ to highlight
SPEAKERS.
3. Press or to highlight OFF.
4. Press EXIT to return to normal
viewing.
To turn on the built-in speakers:
Highlight ON in step 3, above.
Selecting the HDMI™ audio input source
See page 13 for details on connecting an HDMI or DVI device to the
TV’s HDMI input.
If you connect a DVI device, to hear audio you must also connect the
analog audio cables to the HDMI audio IN jacks (see page 13). Set the
HDMI audio input setting to “DVI” with this connection.
If you connect an HDMI device and play media with digital audio
output, to hear digital audio, set the HDMI audio input setting to “HDMI”
with this connection.
If you connect an HDMI device but play media with analog audio
output (for example, certain CDVs do not output digital audio), to hear
audio you must also connect analog audio cables to the HDMI audio IN
jacks (see page 13). Set the HDMI audio input setting to “DVI” with this
connection.
To select the HDMI audio input source:
1. Press MENU, and then press or to display the AUDIO menu.
2. Press or to highlight HDMI.
3. Press or to select HDMI or DVI.
4 Press EXIT to return to normal viewing.
38
J3W60321A_En_p38-Back
38
27/2/06, 9:56 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the BBE® sound feature
By correcting the phase delay and distortion naturally generated by
speaker systems, the BBE* sound feature ensures that the sound that
reaches your ears is as natural as the original sound. Human voices
are clearer and music is natural and well-defined.
Note:
Make sure the volume control of your audio
amplifier is set to a moderate listening level.
To turn on the BBE sound feature:
1. Press MENU, then press or until the AUDIO menu appears.
2. Press ▲ or ▼ to highlight BBE.
3. Press or to highlight ON.
Menu/Enter
4. Press EXIT to return to normal viewing.
To turn off the BBE sound feature:
Highlight OFF in step 3, above.
Exit
* Licensed by BBE Sound, Inc. under one or more of the following US patents:
5510752, 5736897.
BBE and BBE symbol are registered trademarks of BBE Sound, Inc.
Selecting the audio languages
When two or more audio languages are included in a digital signal, you
can select one of the audio languages.
To select the audio language:
1. Press MENU, then press or to display the AUDIO menu.
2. Press ▲ or ▼ to highlight AUDIO LANGUAGE, then press
.
3. Press ▲ or ▼ to select the desired language, then press ENTER.
4. Press EXIT to return to normal viewing.
Selecting the digital output format
Use this feature to select the digital audio output format when
you connect a Dolby** Digital decoder or other digital audio
system to the coaxial digital audio output on the TV (see
“Connecting an A/V amplifier with built-in digital surround” on
page 14).
To select the digital output format:
1. Press MENU, then press or to display the AUDIO menu.
2. Press ▲ or ▼ to highlight DIGITAL OUTPUT.
3. Press or to highlight PCM or DOLBY DIGITAL.
4. Press EXIT to return to normal viewing.
** Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
39
J3W60321A_En_p38-Back
39
27/2/06, 9:56 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Resetting your audio adjustments
The RESET function returns your audio adjustments to the following
factory settings:
Recall
Bass ................. center (25)
Treble ............... center (25)
Balance .............. center (0)
To reset your audio adjustments:
1. Press MENU, then press or to display the AUDIO menu.
Menu
Exit
2. Press ▲ or ▼ to highlight RESET, and then press
.
Checking the digital signal strength
You can check the strength of the digital signal by viewing the digital
signal meter.
To view the digital signal meter:
1. Press MENU, then press or to display the SETUP menu.
2. Press ▲ or ▼ to highlight SIGNAL METER.
3. Press or to check the digital signal strength.
SIGNAL METER
CHANNEL (DIGITAL)
1-001
80
Note:
• The signal meter feature is not available for
analog channels.
• After approximately 4 minutes, the SIGNAL
METER screen will return to normal TV-
operation automatically.
4. Press EXIT to return to the normal screen.
• When you select a vacant channel, the
signal meter may react.
Displaying TV status information on-screen
Press RECALL to display the following information on-screen:
Analog channel:
• Clock
Note:
STEREO
SAP
TV-PG
• Channel number or VIDEO mode
selected
L
V
• Analog channel status will display on the
screen for approx. 4 seconds.
• Digital channel status will display on the
screen for approx. 10 seconds. Press
RECALL again, the analog channel status
will display.
ON TIMER
12:00AM
12:00PM
SLEEP TIMER 2h00m
OFF TIMER
GAME TIMER
30m
• Channel label (if set)
• Stereo or SAP (second audio
program) audio status
• Content rating
• On timer, Off timer, GameTimer,
Sleep timer (if set)
ANT
ABCD
CABLE
NATURAL
007
CLOCK 12:00AM SUN
• Picture size
Digital channel:
• Clock
• Channel number, station name,
program name
• Remaining time
• Audio language
• Content rating
• HD or SD mark
• Closed Caption mark
• V-Chip mark
40
J3W60321A_En_p38-Back
40
27/2/06, 9:56 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto power off
The TV will automatically turn off after approximately 15 minutes if it is tuned to a vacant channel or a station that completes its
broadcast for the day and stops broadcasting on that channel. This feature does not work in video input mode.
Understanding the Power Return feature
If the power is cut off while you are viewing the TV and the power is resupplied, the Power Return feature will turn the TV
on automatically. If the power is going to be off for a long time or you are going to be away from the TV for a long time,
unplug the power cord from the wall outlet to prevent the TV from turning on in your absence.
Appendix
Troubleshooting
Before calling a service technician, please check the following table for a possible cause of the symptom and some solutions.
Symptom
Black box on screen
Solution
• Select OFF in the Closed Caption menu to turn off the Closed Caption
Text mode.
TV will not turn on
• Make sure the power cord is plugged in, then press POWER.
• The remote control batteries may be dead. Replace the batteries.
No picture, no sound
No sound, picture OK
• Check the antenna/cable connections.
• The sound may be muted. Press VOLUME.
• The station may have broadcast difficulties. Try another channel.
• The MTS feature may be in SAP mode. Select STR or MONO in the
MTS menu.
Poor sound, picture OK
• The station may have broadcast difficulties. Try another channel.
• The MTS feature may be in SAP mode. Select STR or MONO in the
MTS menu.
Poor picture, sound OK
• Check the antenna connections.
• The station may have broadcast difficulties. Try another channel.
• Adjust the PICTURE menu.
Poor reception of broadcast channels
• The station may have broadcast difficulties. Try another channel.
• Check the antenna connections.
• If you are using a video input, make sure the TV/VIDEO button is set
correctly.
Cannot receive above channel 13
Unable to select a certain channel
•
Make sure the TV/CABLE feature in the SETUP menu is set to “CABLE.”
• The channel may be blocked by the V-Chip feature or CH LOCK
feature, or erased with the add/erase feature.
Cannot access signal input sources (VIDEO-1, • Check the VIDEO LOCK feature.
VIDEO-2, VIDEO-3, ColorStream HD-1, Color-
Stream HD-2, and HDMI) and/or Channels 3 and 4
Multiple images
• The station may have broadcast difficulties. Try another channel.
• Use a highly directional outdoor antenna.
Poor color or no color
• The station may have broadcast difficulties. Try another channel.
• Adjust the TINT and/or COLOR in the PICTURE menu.
• If you change the direction of the TV while it is turned on, the picture
could suffer from color shading. If so, turn off the TV and allow it to cool
for several hours before turning it on again.
No stereo or SAP sound from a
known MTS broadcast
• Make sure the MTS feature (in the AUDIO menu) is set properly.
The V-Chip password does not work
(U.S. V-Chip system only)
• Change or reset your password.
The remote control does not operate
• Make sure the TV • CBL/SAT • VCR • DVD mode is set properly on the
remote control.
• Remove all obstructions between the remote control and the TV.
• The remote control batteries may be dead. Replace the batteries.
The front panel buttons do not operate
Digital broadcasting screen problem
Closed Caption box appears with no text
• Check the FRONT PANEL LOCK feature.
• Check the digital signal strength.
• Make sure the Closed Caption “Text Color” and “Background Color” are
not set to the same color (see page 36).
41
J3W60321A_En_p38-Back
41
27/2/06, 9:56 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
• This model complies with the specifications below.
• Design and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added in the future.
Picture Tube
26 in. (656.7 mm) diagonal
(Screen size is approximate.)
Television system
Channel coverage
NTSC standard, ATSC standard (8VSB), QAM
VHF: 2–13
UHF: 14–69
Cable TV: 4A, A-5–A-1, A-I,
+
+
J–W, W 1–W 84
Power source
120V AC, 60 Hz
Power consumption
Audio power
160 W
5.0 W + 5.0 W
Speaker type
1-13/16 x 3-7/8 in. (45.7 x 99.1 mm) x 2 pcs.
Video/Audio terminals
S-VIDEO INPUT
Y-INPUT: 1V (p-p), 75 ohm, negative sync.
C-INPUT: 0.286V (p-p) (burst signal), 75 ohm
VIDEO/AUDIO INPUT
VIDEO: 1V (p-p), 75 ohm, negative sync.
AUDIO: 300 mV (rms) (60% modulation equivalent, 35k ohm)
ColorStream® (component video) INPUT
Y: 1V (p-p), 75 ohm
PR: 0.7V (p-p), 75 ohm
PB: 0.7V (p-p), 75 ohm
AUDIO OUTPUT
300 mV (rms) (60% modulation equivalent, 1k ohm)
DIGITAL AUDIO OUTPUT
AUDIO: 0.5V (p-p), 75 ohm
HDMI INPUT: HDMI compliant (type A connector)
HDCP compliant
E-EDID compliant
Suggested scan rates: 1080i, 480p, 480i, 720p
HDMI Audio: 2-channel PCM
32/44.1/48 kHz sampling frequency
16/20/24 bits per sample
Dimensions
Width: 27-9/16 in. (700 mm)
Depth: 19-3/4 in. (502 mm)
Height: 19-1/2 in. (495.5 mm)
Weight
78.3 lbs. (35.5 kg)
Supplied accessories
Remote control with two size “AAA” batteries
42
J3W60321A_En_p38-Back
42
27/2/06, 9:56 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited United States Warranty
for all FST PURE® CRT-based TVs and Projection TVs 26” and Larger
Toshiba America Consumer Products, L.L.C. (“TACP”) makes the
Your Responsibility
following limited warranties to original consumers in the United
States. THESE LIMITED WARRANTIES EXTEND TO THE
ORIGINAL CONSUMER PURCHASER OR ANY PERSON
RECEIVING THIS TELEVISION AS A GIFT FROM THE ORIGINAL
CONSUMER PURCHASER AND TO NO OTHER PURCHASER
OR TRANSFEREE.
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING
CONDITIONS:
(1) You must retain your original bill of sale or provide other proof of
purchase.
(2) All warranty servicing of this television must be performed by a TACP
Authorized Service Station.
(3) The warranties from TACP are effective only if this television is
purchased and operated in the Continental U.S.A. or Puerto Rico.
(4) Labor service charges for set installation, setup, adjustment of
customer controls, and installation or repair of antenna systems are
not covered by this warranty. Reception problems caused by
inadequate antenna systems, misaligned satellite dishes, cable
television distribution, VCRs, DVD players/recorders, personal
computer level IEEE-1394 devices, and any other connected signal
source device are your responsibility.
TELEVISIONS PURCHASED IN THE U.S.A. AND USED
ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT
LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY
THESE WARRANTIES.
TELEVISIONS PURCHASED ANYWHERE OUTSIDE OF THE
U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND
MEXICO, AND USED IN THE U.S.A., ARE NOT COVERED BY
THESE WARRANTIES.
Limited One (1) Year Warranty on Parts and Labor
(5) Warranties extend only to defects in materials or workmanship as
limited above, and do not extend to any television or parts that have
been lost or discarded by you or to damage to the television or parts
caused by fires, misuse, accident, Acts of God (such as lightning or
fluctuations in electric power), improper installation, improper
maintenance, or use in violation of instructions furnished by TACP;
use or malfunction through simultaneous use of this television and
connected equipment; or to units that have been modified or had the
serial number removed, altered, defaced, or rendered illegible.
TACP warrants this television and its parts against defects in materials
or workmanship for a period of one (1) year after the date of original
retail purchase. DURING THIS PERIOD, TACP WILL, AT TACP’S
OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A
NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU FOR
PARTS OR LABOR. During this period, TACP Authorized Service
Station personnel will come to your home when warranty service is
required. Depending on the type of repair required, the service will
either be performed in your home or the television will be taken to a
TACP Authorized Service Station for repair and returned to your home
at no cost to you.
How to Obtain Warranty Service
If, after following all of the operating instructions in this manual and
reviewing the section entitled “Troubleshooting,” you find that service
is needed:
Limited Two (2) Year Warranty on Picture Tube
TACP warrants the picture tube in this television against defects in
materials or workmanship for a period of two (2) years after the date
of original retail purchase. DURING THIS PERIOD, TACP WILL, AT
TACP’S OPTION, REPAIR OR REPLACE A DEFECTIVE PICTURE
TUBE WITH A NEW OR REFURBISHED PICTURE TUBE
WITHOUT CHARGE TO YOU, PROVIDED THAT IF A DEFECTIVE
PICTURE TUBE IS REPAIRED OR REPLACED AFTER ONE (1)
YEAR AFTER THE DATE OF ORIGINAL RETAIL PURCHASE, YOU
MUST PAY FOR ALL LABOR CHARGES IN CONNECTION WITH
THE REPAIR OR REPLACEMENT THEREOF. During this period,
TACP Authorized Service Station personnel will come to your home
when warranty service is required. Depending on the type of repair
required, the service will either be performed in your home or the
television will be taken to a TACP Authorized Service Station for repair
and returned to your home at no cost to you.
(1) To find the nearest TACP Authorized Service Station, visit TACP’s
Consumer Solution Center toll free at 1-800-631-3811.
(2) You must present your original bill of sale or other proof of
purchase to the TACP Authorized Service Station.
For additional information, visit TACP’s website:
ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE
U.S.A., INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED
WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY
WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE U.S.A.
AS HEREBY LIMITED, THE FOREGOING WARRANTY IS
EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
GUARANTEES, AGREEMENTS, AND SIMILAR OBLIGATIONS OF
TACP WITH RESPECT TO THE REPAIR OR REPLACEMENT OF ANY
PARTS. IN NO EVENT SHALL TACP BE LIABLE FOR
Rental Units
The warranty for television rental units begins on the date of the first
rental or thirty (30) days after the date of shipment to the rental firm,
whichever comes first.
CONSEQUENTIAL OR INCIDENTAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, LOST PROFITS, BUSINESS INTERRUPTION, OR
MODIFICATION OR ERASURE OF RECORDED DATA CAUSED BY
USE, MISUSE, OR INABILITY TO USE THIS TELEVISION).
Limited Warranty for Commercial Units
TACP warrants televisions that are sold and used for commercial
purposes as follows: all parts are warranted against defects in
materials or workmanship for a period of ninety (90) days after the
date of original retail purchase. DURING THIS PERIOD, TACP
WILL, AT TACP’S OPTION, REPAIR OR REPLACE A DEFECTIVE
PART WITH A NEW OR REFURBISHED PART WITHOUT
CHARGE TO YOU.
No person, agent, distributor, dealer, or company is authorized to
change, modify, or extend the terms of these warranties in any manner
whatsoever. The time within which an action must be commenced to
enforce any obligation of TACP arising under the warranty or under any
statute or law of the United States or any state thereof is hereby limited
to ninety (90) days from the date you discover, or should have
discovered, the defect. This limitation does not apply to implied
warranties arising under the law of any state of the U.S.A.
Owner’s Manual and Product Registration Card
Read this owner’s manual thoroughly before operating this television.
Complete and mail the enclosed product registration card or register
as possible. By registering your television you will enable TACP to
bring you new products specifically designed to meet your needs and
help us to contact you in the unlikely event a safety notification is
required under the U.S. Consumer Product Safety Act. Failure to
complete and return the product registration card does not diminish
your warranty rights.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU
MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE
TO STATE IN THE U.S.A. SOME STATES OF THE U.S.A. DO NOT ALLOW
LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY,
WHEN AN ACTION MAY BE BROUGHT, OR THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES.
THEREFORE, THE ABOVE PROVISIONS MAY NOT APPLY TO YOU
UNDER SUCH CIRCUMSTANCES. [Wty-A(E) 0305]
43
J3W60321A_En_p38-Back
43
27/2/06, 9:56 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
National Service Division
CableClear, ColorStream, FST Pure, TheaterWideand StableSoundare
registered trademarks of Toshiba America Consumer Products, L.L.C.
GameTimer is a trademark of Toshiba America Consumer Products, L.L.C.
PRINTED IN THAILAND
J3W60321A_En_p38-Back
44
27/2/06, 9:56 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
26HF66
J3W60321B(S)_COVER
1
3/4/06, 6:11 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Estimado cliente.
Le agradecemos que haya comprado este televisor
TOSHIBA. Este manual le ayudará a utilizar las numerosas
e interesantes funciones de su nuevo televisor.
Antes de hacer funcionar el televisor, lea este
manual en su totalidad y consérvelo en un lugar
conveniente para consultarlo en el futuro.
Seguridad infantil
El lugar en que se coloca el televisor es
muy importante
¡Felicitaciones por su compra!
Tenga en mente estos consejos
de seguridad mientras disfruta de
su televisor:
Precauciones de seguridad
ADVERTENCIA
PARA REDUCIR EL RIESGO DE INCENDIO O
DESCARGA ELÉCTRICA, NO EXPONGA ESTE
APARATO A LA LLUVIA O A LA HUMEDAD.
El problema
ꢀ
ꢀ
Si usted es como la mayoría de las personas, usted tiene un televisor
en su hogar. Es más, muchos hogares tienen más de un televisor.
La posibilidad de disfrutar la experiencia del teatro en casa
es una tendencia en aumento y los televisores grandes están
muy de moda; el problema es que no siempre se colocan sobre
una base adecuada.
PRECAUCIÓN
RIESGO DE DESCARGA
ELÉCTRICA. NO ABRIR
ADVERTENCIA: PARA REDUCIR EL RIESGO DE
DESCARGA ELÉCTRICA, NO RETIRE LA CUBIERTA
(NI LA PARTE POSTERIOR). NO HAY NINGÚN
COMPONENTE EN EL INTERIOR QUE EL USUARIO
PUEDA REPARAR. ENCARGUE TODAS LAS
ꢀ
A veces los aparatos no están bien asegurados o se sitúan de
manera poco adecuada sobre tocadores, libreros, estantes,
escritorios, altavoces, arcones o carritos. Como resultado,
el televisor se puede caer y causar lesiones innecesarias.
REPARACIONES A UN TÉCNICO CALIFICADO.
El símbolo de rayo en un triángulo indica que el voltaje
en el interior de este producto puede causar descargas
eléctricas. NO INTENTE REPARAR ESTE PRODUCTO
USTED MISMO.
¡Toshiba se preocupa!
ꢀ
La industria de los aparatos electrónicos de
consumo se ha impuesto el compromiso de
hacer que el entretenimiento en el hogar
sea agradable y sin riesgos.
El signo de admiración en un triángulo indica que el
texto que sigue contiene instrucciones importantes
de mantenimiento y funcionamiento.
ꢀ
La Asociación de Aparatos
Electrónicos de consumo formó la
Comisión de Seguridad para el Apoyo
del Entretenimiento en el Hogar (la
cual comprende a fabricantes de
televisores y muebles para aparatos
electrónicos de consumo) con la
finalidad de velar por la seguridad
infantil y educar al consumidor y a su
familia acerca de la seguridad del TV.
CUIDADO: Para prevenir descargas eléctricas,
no usar este enchufe polarizado con una
extensión eléctrica, receptáculo u otro
tomacorriente a menos que las clavijas puedan
insertarse para prevenir su exposicón.
AVISO A LOS INSTALADORES DE TELEVISIÓN
POR CABLE (CABLE TV, CATV)
Sintonice la seguridad
Este es un recordatorio para los instaladores de sistemas de
CATV sobre el Artículo 820-40 de la NEC, que dispone pautas
para la conexión a tierra correcta y especifica en particular
que el cable de tierra se debe conectar al sistema de conexión
a tierra del edificio, lo más cerca posible del punto de entrada
del cable. Consulte los puntos 26 y 27 en la página 4, para
obtener información adicional sobre la conexión a tierra de
la antena.
ꢀ
¡Aquí NO corresponde el concepto de
unitalla! Use un mueble adecuado de tamaño
suficiente para soportar el peso de su televisor
(y otros componentes electrónicos).
ꢀ
Use soportes de ángulo, abrazaderas y anclajes apropiados
para asegurar el mueble a la pared (pero nunca atornille
ninguna cosa directamente en el televisor).
ꢀ
ꢀ
ꢀ
Lea atentamente las instrucciones adjuntas hasta entenderlas
AVISO DE POSIBLES EFECTOS ADVERSOS
EN LA PANTALLA DEL TELEVISOR
para que pueda utilizar este producto de la manera adecuada.
No permita que los niños se trepen sobre los muebles y los
televisores y no permita que jueguen con ellos.
No ponga cosas encima del televisor (la videocasetera, el
control remoto o los juguetes) que un niño curioso pueda querer
alcanzar.
Tenga presente que los niños se pueden emocionar mucho
cuando están viendo un programa y pueden empujar el
televisor o volcárselo encima.
Si una imagen fija (que no se mueve) permanece en la
pantalla del televisor por mucho tiempo, puede quedar
grabada en forma definitiva en el tubo de imagen.
Este tipo de daño NO ESTÁ CUBIERTO POR SU
GARANTÍA. Vea el apartado 34 en la página 4.
ꢀ
ꢀ
TV calificado como ENERGY STAR®. Los
productos que logran el ENERGY STAR previenen
la emisión de gases invernadero al cumplir con
normas estrictas en eficiencia de energía, fijadas
por la Agencia de Protección del Medio Ambiente
de los EE.UU. y el Departamento de Energía de los
EE.UU. ENERGY STAR y la marca ENERGY STAR
son marcas registradas de los EE.UU.
Difunda entre sus familiares y amigos nuestro mensaje de
seguridad acerca de este peligro oculto en el hogar. ¡Gracias!
2500 Wilson Blvd.
Arlington, VA 22201 U.S.A.
Tel. 703-907-7600 Fax 703-907-7690
NUNCA CONECTE ESTETV A UNA COMPUTADORA
CEA es el patrocinador, productor y
PERSONAL (PC). Este TV no se diseñó para usarse
0303
administrador de la CES® Internacional.
con una PC.
2
J3W60321A(S)_P02-06
2
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Instrucciones de seguridad importantes Instalación, cuidado y servicio
Instalación
1) Lea estas instrucciones.
Siga estas recomendaciones y precauciones y tenga en mente todas
las advertencias cuando instale su televisor:
2) Conserve estas instrucciones.
3) Preste atención a todas las advertencias.
4) Siga todas las instrucciones.
16) No modifique este equipo. Los cambios o modificaciones
pueden anular: a) la garantía y b) la autoridad del usuario para
operar este equipo bajo las reglas de la Comisión Federal de
Comunicaciones (Federal Communications Commission, FCC.)
5) No use este aparato cerca del agua.
6) Límpielo únicamente con un paño seco.
17)
PELIGRO: ¡RIESGO DE LESIÓN GRAVE,
MUERTE O DAÑO AL EQUIPO!
7) No bloquee las rejillas de ventilación.
Instale el aparato de acuerdo con las instrucciones del fabricante.
Nunca coloque el televisor sobre
8) No instale el aparato cerca de fuentes de calor tales como
radiadores, salidas de calefacción, cocinas y otros aparatos
(incluidos los amplificadores) que producen calor.
un carrito, base o mesa inestables. Puede
caerse y causar lesiones graves, muerte o
daño considerable al televisor.
9) No anule el diseño de seguridad del enchufe polarizado o
con conexión a tierra. Los enchufes polarizados tienen dos
clavijas, una de las cuales es más ancha que la otra.
18) Nunca sitúe ni guarde el televisor a la
luz directa del sol; en lugares cálidos o
húmedos; en lugares expuestos al polvo
o la vibración excesivos o en lugares con
temperaturas de 5 °C (41 °F) o menos.
Clavija ancha
Los enchufes con conexión a tierra tienen
dos clavijas planas y una redonda que sirve
de conexión a tierra. La clavija ancha y la
tercera clavija, respectivamente, son para
su seguridad. Si el enchufe del aparato
no entra en el enchufe de la pared, consulte a un técnico
electricista para que cambie el enchufe de pared obsoleto.
19) Coloque siempre el televisor en el piso
sobre una superficie resistente, nivelada
y estable que sea capaz de soportar
el peso de la unidad.
10) Proteja el cordón eléctrico para que
no lo pisen ni lo aprieten, en particular
cerca del enchufe, en el enchufe en
sí y en el punto en que sale del aparato.
11) Use únicamente los accesorios especificados por el fabricante.
20) Nunca coloque objetos tales como
floreros, acuarios o velas encima del
televisor.
12) Use únicamente el carrito, base, trípode,
soporte o mesa que especifique el
fabricante o que se venda con el aparato.
Si usa un carrito, proceda con precaución al
mover la combinación carrito/aparato para
evitar que se le caiga encima y lo lesione.
21) Nunca bloquee ni cubra las rejillas o aberturas de las partes
posterior, inferior y laterales de la caja del televisor. Nunca
coloque el televisor:
• sobre una cama, sillón, alfombra
13) Desconecte el aparato durante las
tormentas eléctricas o cuando no
lo vaya a utilizar por períodos de
tiempo prolongados.
o superficie similar;
• demasiado cerca de cortinas,
persianas, paredes o
• en un lugar encerrado, como por
ejemplo un librero, un estante
empotrado u otros lugares que
no tengan buena ventilación.
14) Encargue todas las reparaciones y servicio a
personal calificado. El aparato debe ser enviado a un
técnico calificado si se deja caer, si funciona
anormalmente o si sufre daños tales como roturas del
cordón de alimentación o del enchufe, derrame de
líquidos o caída de objetos en el interior o exposición a la
lluvia o a la humedad.
Las rejillas y aberturas tienen la
finalidad de proteger el aparato contra
el sobrecalentamiento y de conservarlo
en un buen estado de funcionamiento.
14a) ATENCIÓN: En el caso de que el televisor se caiga y se dañe el
gabinete o la superficie circundante, y/o que el televisor no
funcione normalmente, tome las siguientes precauciones:
• SIEMPRE apague el televisor y desenchufe el cable para
evitar posibles descargas eléctricas o incendios.
22) Siempre coloque la parte posterior del televisor por lo menos a
una (1) pulgada de cualquier superficie vertical (como una
pared) para permitir la ventilación adecuada.
23) No apoye o haga rodar objetos sobre el cordón eléctrico, ni
coloque el televisor donde el cordón se pueda desgastar o
quedar expuesto a maltrato.
• Para evitar lesiones personales, nunca manipule el
televisor si estuviera dañado.
• SIEMPRE que el televisor esté dañado o se haya caído,
llame a un técnico de servicio para inspeccionarlo.
15)
CUIDADO: Para prevenir descargas eléctricas, no usar
este enchufe polarizado con una extensión eléctrica,
receptáculo u otro tomacorriente a menos que las clavijas
puedan insertarse para prevenir su exposicón.
24) Nunca sobrecargue los enchufes de
pared ni las extensiones.
0303
3
J3W60321A(S)_P02-06
3
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
31) [Esta instrucción aplica sólo a los televisores de proyección.]
Si la temperatura del aire aumenta repentinamente (por ejemplo,
cuando le entregan el televisor), se puede formar condensación en
las lentes. Esto puede hacer que la imagen se vea distorsionada o
que el color se vea desvanecido. Si esto ocurre, apague el televisor
y no lo vuelva a encender durante 6 ó 7 horas para que la humedad
se evapore.
25) Conecte este equipo únicamente a una
fuente de alimentación de 120 V CA,
60 Hz.
26) Verifique siempre que el sistema de la antena esté conectado a
tierra correctamente para proteger adecuadamente el aparato
contra las subidas de voltaje y las cargas de energía estática
acumulada (consulte la Sección 810 del Código Eléctrico Nacional).
32) Con el fin de protegerlo contra las subidas de voltaje y los
rayos, desconecte el televisor y la antena si no lo va a usar
por períodos prolongados.
Acometida de antena
33) Durante el uso normal es posible que el
televisor haga ruidos de vez en cuando.
Esto es normal, especialmente en el
momento de encenderlo y apagarlo.
Si los ruidos se vuelven frecuentes
o continuos, desconecte el televisor
y comuníquese con un centro de servicio
autorizado de TOSHIBA.
Unidad de descarga de la antena
Abrazadera de
(Sección 810-20 del NEC)
conexión a tierra
Conductores de conexión a tierra
Equipo del servicio de
(Sección 810-21 del NEC)
suministro eléctrico
Sistema de electrodos de conexión a tierra
del servicio de suministro eléctrico
Abrazaderas de
conexión a tierra
(Artículo 250, Parte H del NEC)
34) Posibles efectos adversos sobre la pantalla del televisor: Si
una imagen fija (que no se mueve) permanece en la pantalla del
televisor por mucho tiempo, puede quedar grabada en forma
definitiva en el tubo de imagen y dejar una imagen fantasma tenue
pero permanente en la pantalla. Este tipo de daño NO ESTÁ
CUBIERTO POR SU GARANTÍA. Nunca deje el televisor
encendido por períodos prolongados cuando esté mostrando los
siguientes formatos o imágenes:
27)
PELIGRO: ¡RIESGO DE LESIÓN GRAVE O MUERTE!
• Proceda con extremada cautela para asegurarse de
que nunca se encuentre en una posición en la cual su
cuerpo (o cualquier objeto con el que tenga contacto, como por
ejemplo una escalera o un destornillador) pueda tocar
accidentalmente los cables aéreos de alta tensión. Nunca sitúe la
antena cerca de los cables aéreos de alta tensión u otros circuitos
eléctricos.
• Imágenes fijas, tales como ventanas PIP/POP, cintas de datos
bursátiles, patrones de juegos de video, logotipos de estaciones
de TV, subtítulos ocultos y sitios Web.
• Nunca intente instalar lo siguiente durante tormentas eléctricas:
a) sistema de antena, b) cables o componentes de teatro en casa
conectados a la antena o al sistema de teléfonos.
• Formatos especiales que no utilizan la pantalla completa. Por
ejemplo, ver un programa en formato 16:9 en una pantalla normal
4:3 (barras grises en la parte superior e inferior de la pantalla); o
ver un programa en formato normal 4:3 en una pantalla ancha de
formato 16:9 (barras grises sobre los costados izquierdo y
derecho de la pantalla).
Cuidado
Siga estas recomendaciones y observe estas precauciones para lograr
el mejor rendimiento y un funcionamiento seguro de su televisor
TOSHIBA:
Servicio
35)
ADVERTENCIA: ¡RIESGO DE DESCARGA
ELÉCTRICA! Nunca trate de
reparar el televisor usted
28) Siéntese siempre a una distancia entre 3 y 7.5 metros (10 a 25 pies)
del televisor y, de ser posible, directamente enfrente. Si se sienta
demasiado a la izquierda o a la derecha, o si la luz solar o de las
lámparas de la habitación se refleja en la pantalla, la imagen puede
parecer pálida. Apague el televisor para comprobar si se ven
reflejos en la pantalla, luego elimine la fuente del reflejo mientras
vea televisión.
mismo. Abrir o quitar las tapas puede
exponerlo a voltajes peligrosos u otros
riesgos. Encargue las reparaciones a
un centro de servicio autorizado de TOSHIBA.
36) Si le reparan el televisor:
• Pídale al técnico que utilice únicamente repuestos especificados
por el fabricante.
29) Desconecte siempre el televisor
antes de limpiarlo. Nunca utilice
limpiadores líquidos o limpiadores
en aerosol.
• Una vez concluída la reparación,
pídale al técnico que haga las
comprobaciones de seguridad
de rutina para determinar que
el televisor funciona sin peligro.
37) Cuando el televisor llegue al fin de su vida útil, pídale a un técnico
de servicio calificado que lo deseche de manera adecuada. El
desecho incorrecto puede causar implosión del tubo de imagen y
posibles lesiones personales.
30)
¡ADVERTENCIA: RIESGO DE DESCARGA
ELÉCTRICA! Nunca derrame líquidos ni introduzca
objetos en las ranuras de la caja del televisor.
0303
4
J3W60321A(S)_P02-06
4
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Información importante sobre seguridad .................................................................................................................... 2 - 4
Bienvenido a Toshiba ...........................................................................................................................................................6
Explorando su nueva TV .................................................................................................................................................6
Seleccionando un lugar para la TV .................................................................................................................................6
Conectando su televisor ......................................................................................................................................................7
Conectando una videograbadora ....................................................................................................................................7
Conectando una caja convertidora para cable TV o Antena ...........................................................................................8
Conectando un reproductor de DVD/receptor satelital y una videograbadora................................................................9
Conectando un reproductor de DVD con ColorStream® (componente de video) y una videograbadora ......................10
Conectando un receptor de DTV o caja de conexión con un video componente ColorStream® y una videograbadora .. 11
Conectando una videocámara ......................................................................................................................................12
Conexión de un dispositivo de HDMI™ o DVI ..............................................................................................................13
Conexión de un sistema de audio analógico ................................................................................................................14
Conectando un amplificador A/V con sonido surround digital incorporado ..................................................................14
Usando el control remoto...................................................................................................................................................15
Preparando el control remoto para su uso ....................................................................................................................15
Instalando las baterías del control remoto ....................................................................................................................15
Usando el control remoto para operar otros aparatos ..................................................................................................15
Programando el control remoto para operar otros aparatos .........................................................................................16
Tablas de código de dispositivos ...................................................................................................................................17
Aprendiendo sobre el control remoto ............................................................................................................................19
Configurando su televisor..................................................................................................................................................20
Empezando configuración.............................................................................................................................................20
Cambiando el idioma de despliegue en la pantalla.......................................................................................................20
Corrección de inclinación de la imagen ........................................................................................................................21
Agregando canales a la memoria de el televisor ..........................................................................................................21
Usando las funciones de el televisor ................................................................................................................................22
Ajustando la configuración de los canales ....................................................................................................................22
Usando el menú de BLOQUEAR ..................................................................................................................................23
Seleccionando una Contraseña ............................................................................................................................23
La función del V-Chip (control paterno).................................................................................................................24
Bloqueando los canales ........................................................................................................................................25
Bloqueando la entrada de video ...........................................................................................................................26
Configurando el GameTimer™ (Tiempo de juego) ...............................................................................................26
Usando la función de bloqueo del panel frontal ....................................................................................................27
Creando las etiquetas de los canales ...........................................................................................................................27
Seleccionando la fuente de entrada de video ...............................................................................................................28
Creando las etiquetas de las fuentes de entrada de video ...........................................................................................28
Configurando el reloj .....................................................................................................................................................29
Configurando el cronómetro de ENCENDIDO/APAGADO ...........................................................................................29
Viendo los formatos de imágenes de pantalla amplia (Sólo para señales de 480i y 480p) ..........................................30
Desplazando la imagen TheaterWide® (sólo Dimensión Cine2 y 3) .............................................................................32
Seleccionando la modalidad CINEMA ..........................................................................................................................33
Seleccionando el formato de despliegue (sólo para señales de 480p).........................................................................33
Ajustando la imagen......................................................................................................................................................33
Seleccionando la modalidad de la imagen............................................................................................................33
Ajustando la calidad de la imagen ........................................................................................................................34
Seleccionando la temperatura del color ................................................................................................................34
Usando la función CableClear® .............................................................................................................................35
Seleccionando la Modulación de Velocidad de la Exploración (SVM – Scan Velocity Modulation) ......................35
Restableciendo sus ajustes de la imagen .............................................................................................................35
Configurando el cronómetro apagado automatico (sleep timer) ...................................................................................36
Usando la función de subtítulos ....................................................................................................................................36
Usando la functión de subtítulos avanzados.................................................................................................................36
Ajustando el sonido .......................................................................................................................................................37
Enmudeciendo el sonido .......................................................................................................................................37
Seleccionando las estaciones en estéreo/SAP.....................................................................................................37
Ajustando la calidad del sonido.............................................................................................................................37
Usando la función de sonido StableSound® ..........................................................................................................38
Apagando los altavoces incorporados ..................................................................................................................38
Seleccionando la fuente de entrada de audio HDMI™ .........................................................................................38
Usando la función de sonido BBE® .......................................................................................................................39
Selección de idiomas del audio.............................................................................................................................39
Seleccionando el formato de salida digital ............................................................................................................39
Restableciendo sus ajustes de audio....................................................................................................................40
Cómo comprobar la potencia de la señal digital ...........................................................................................................40
Desplegando la información del estado de la TV en pantalla .......................................................................................40
Apagado automático .....................................................................................................................................................41
Entendiendo la función de Retorno de Energía ............................................................................................................41
Apéndice ..............................................................................................................................................................................41
Solución de problemas..................................................................................................................................................41
Especificaciones ...........................................................................................................................................................42
Garantía limitada de los Estados Unidos .....................................................................................................................43
5
J3W60321A(S)_P02-06
5
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Bienvenido a Toshiba
¡Felicitaciones! Usted ha comprado uno de los televisores a color más
finos del mercado. La meta de este manual es guiarlo completamente
a preparar y a operar su televisor tan rápidamente como sea posible.
La función EMPEZAR AJUSTE aparecerá
la primera vez que encienda el televisor.
Vea la página 20 para obtener detalles.
Usted podrá necesitar comprar otros cables de audio o video para
conectar su equipo. Vea “Conectando su TV” en la página 7 para más
información.
Por favor lea cuidadosamente todas las instrucciones operativas y de
seguridad antes de empezar.
Explorando su nueva TV
Usted podrá operar su televisor al usar los botones en el panel frontal
o el control remoto. Los paneles frontal y trasero proporcionan todas
las entradas que necesitará para conectar otro equipo a su televisor.
Panel delantero de la TV
Sensor de
control remoto
Selectores de
canal en ▼/▲
Conectores de entrada
de Audio (I/D)/Video
Comandos de
volumen▼/▲
Indicador de
encendido
Interruptor
S-Video
Panel trasero de la TV
Seleccionando un lugar para la TV
• Coloque la televisor en el piso o en una plataforma robusta en un
lugar donde la luz no pegue directamente en la pantalla.
• Coloque la televisor lo bastante lejos de las paredes para permitir
la ventilación apropiada. La ventilación inadecuada podría causar
sobrecalentamiento que podría dañar la televisor. Este tipo de
daño NO ESTÁ CUBIERTO POR SU GARANTÍA.
6
J3W60321A(S)_P02-06
6
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conectando su televisor
• Un cable coaxial es un cable normal que entra de su antena o de
la caja convertidora de cable TV. Los cables coaxiales usan
conectores “F.”
• Los cables normales de A/V (audio/video) usualmente están
codificados con colores según su uso: amarillo para video, rojo y
para audio. El cable rojo de audio es para el canal estereofónico
derecho, y el cable blanco de audio blanco es para el canal
estereofónico (o monofónico) izquierdo. Si observa el panel
trasero de el televisor, verá que las terminales están codificadas
con colores de la misma manera que los cables.
NUNCA CONECTE ESTE TV A
UNA COMPUTADORA
PERSONAL (PC). Este TV no se
diseñó para usarse con una PC.
• Los cables de S-video proporcionan un mejor desempeño de la
imagen. Sólo pueden usarse los cables de S-video con los
componentes compatibles de S-video.
• Los cables de video de componentes entran en juegos de tres y
proporcionan el mejor desempeño de la imagen. Los cables de
video de componentes sólo podrán usarse con componentes que
sean compatibles con el video de componentes.
AVISO: ¡RIESGO DE DAÑO
EN EL EQUIPO!
No conecte ningún cable de
corriente hasta que haya
terminado de conectar todo su
equipo.
• El cable de Interfaz para Multimedia de Alta Definición (HDMITM
-
High Definition Multimedia Interface) es para usarse con equipos
de video que tengan salida HDMI (vea la página 13).
• El cable de Interfaz para digital audio coaxial es para usarse con
equipos de video que tengan salida digital audio (vea la página 14).
ANTENA
Cable coaxial
Cables video
componentes
Cables
AUDIO
Cable
HDMI
Cables
VIDEO
Cable Digital
Audio Coaxial
Cables
S-Video
Conectando una videograbadora
Esta conexión le permite ver los canales locales y programas de video,
reproducir o grabar en la videograbadora mientras ve el televisor, y
grabar de un canal mientras ve otro canal.
Usted necesitará lo siguiente:
• Dos cables coaxiales
• Un juego de cables normales de A/V
Panel trasero de la TV
Nota:
Si usa una videograbadora monofónica,
conecte L/Mono a Audio OUT de la
videograbadora usando sólo un cable de
audio. Para obtener una mejor calidad en la
imagen, si su videograbadora tiene S-video,
podrá usar un cable de S-video en lugar del
cable normal de video. No conecte un cable
normal de video y un cable de S-video
simultáneamente a VIDEO-1 (o VIDEO-2 o
VIDEO-3). O la calidad de la imagen será
inaceptable.
Entrada del cable de la
Videograbadora
estereofónica
caja para cable TV o la
La grabación no autorizada, el uso, la
distribución, o la revisión de los
programas televisivos, videos, DVD, y
otros materiales se prohíben bajo las
Leyes de Copyright de los Estados
Unidos y otros países, y usted podría
estar sujeto a la responsabilidad civil y
penal.
antena
7
J3W60321A(S)_P07-14
7
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conectando una caja convertidora para cable
TV o Antena
Este televisor puede sintonizar la mayoría de los canales por cable sin
necesidad de recurrir al convertidor suministrado por los canales de
cable. Algunas compañías de cable ofrecen “canales pagados
exclusivos” en los cuales la señal esta codificada. La decodificación de
esas señales para la obtención de una señal normal requiere el uso de
un decodificador que es generalmente provisto por la compañía de
cable.
Opción 1: PARA LOS ABONADOS A UN SERVICIO DE TV POR
CABLE BASICO
Para un servicio de cable básico que no requiera convertidor/
descodificador, conecte el cable coaxial Cable TV de 75 ohmios
directamente a la entrada de la antena en la parte trasera del televisor.
Opción 2: PARA LOS ABONADOS A UN SERVICIO DE TV POR
CABLE “CODIFICADO”
Si Ud. está suscrito a un servicio de cable que requiere el uso de un
convertidor/descodificador conecte el cable de bajada de antena al
convertidor/descodificador y conecte la salida de ésta a la entrada de
antena en la parte trasera del televisor. Siga la conexión como se
muestra en la figura. Sintonice el televisor en el canal de salida del
convertidor/descodificador (usualmente canal 3 ó 4) y utilice el
convertidor/descodificador para la selección de canales.
Opción 3: PARA ABONADOS A UN SERVICIO DE CABLE BÁSICO
CON CANALES ESPECIALES CODIFICADOS
Si Ud. está suscrito a un servicio de cable en el cual los canales
básicos son comunes y los canales especiales necesitan un
convertidor/descodificador, puede utilizar un divisor de señal (a veces
llamado “acoplador”) y una caja de interruptor A/B. Siga el cableado
como se muestra en la figura. Con el interruptor en la posición “B”,
puede sintonizar directamente cualquier canal común en su televisor.
Con el interruptor en la posición “A” puede sintonizar su TV con la
salida del sintonizador/codificador y usarlo para sitonizar canales
codificados (usualmente canal 3 ó 4).
Nota:
Cuando use una caja convertidora con su
televisor, podría haber funciones que no
pueda programar al usar el control remoto,
como etiquetar los canales, bloquear los
canales, y programar sus canales favoritos.
CATV entrante
Opción 1:
Panel trasero de la TV
Opción 2:
Opción 3:
8
J3W60321A(S)_P07-14
8
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conectando un reproductor de DVD/receptor
satelital y una videograbadora
Usted necesitará lo siguiente:
Esta conexión le permite ver DVD o canales satelitales, videocintas o
programas de televisión. Podrá grabar del receptor satelital y la
televisión, así como grabar un canal de televisión mientras esté viendo
otro canal.
• Tres cables coaxiales
• Dos juegos de cables normales de A/V
• Un cable de S-video
Nota:
Podrá usar un cable normal de video en lugar
del cable de S-video, pero la calidad de la imagen
disminuirá. Si usa un cable de S-video entre el
televisor y el reproductor de DVD/receptor
satelital, sólo haga las conexiones de audio y
quite el cable normal de video. No conecte un
cable S-video y un cable normal de video a
VIDEO-1 (o VIDEO-2 o VIDEO-3) al mismo
tiempo o la representación de la imagen será
inaceptable.
Del satelite
Reproductor de DVD/Receptor satelital
VIDEO
AUDIO
L
R
OUT
Satellite IN
S-VIDEO
OUT to TV
La grabación no autorizada, el uso, la
distribución, o la revisión de los
programas televisivos, videos, DVD, y
otros materiales se prohíben bajo las
Leyes de Copyright de los Estados
Unidos y otros países, y usted podría
estar sujeto a la responsabilidad civil y
penal.
Videograbadora
estereofónica
IN
IN from ANT
OUT to TV
OUT
CH
CH
3
4
V
UDIO
Panel trasero de la TV
9
J3W60321A(S)_P07-14
9
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conectando un reproductor de DVD con
ColorStream® (componente de video) y una
videograbadora
Esta conexión le permite ver DVD, videocintas, o programas de
televisor y grabar programas de televisión. Podrá grabar de una fuente
mientras vea un programa de otra fuente. Su TV puede utilizar las
entradas ColorStream (componente de video). Al conectar su televisor
a un reproductor de DVD compatible con el video de componentes, tal
como un reproductor de DVD Toshiba con ColorStream®, podrá realzar
la calidad de la imagen y el desempeño.
Usted necesitará lo siguiente:
• Dos cables coaxiales
• Un juego de cables normales de A/V
• Un juego de cables componente de video
• Un par de cables normales de audio
Nota:
Podrá conectar los cables de componente de
video a cualquier juego de conectores
ColorStream en el televisor (HD-1 o HD-2).
Los conectores HD-1 y HD-2 ColorStream
pueden usarse con los sistemas de
exploración Progresivo (480p, 720p) y
Entrelazado (480i, 1080i). Una señal de 1080i
proporcionará la mejor representación de la
imagen.
Reproductor de DVD con Componente de video
OUT
L
COMPONENT VIDEO
Y
R
VIDEO
OUT
AUDIO
S-VIDEO
La grabación no autorizada, el uso, la
distribución, o la revisión de los
programas televisivos, videos, DVD, y
otros materiales se prohíben bajo las
Leyes de Copyright de los Estados
Unidos y otros países, y usted podría
estar sujeto a la responsabilidad civil y
penal.
Panel trasero de la TV
De la antena
Videograbadora
estereofónica
IN
IN from ANT
OUT to TV
OUT
CH
CH
3
4
L
R
VIDEO
AUDIO
10
J3W60321A(S)_P07-14
10
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conectando un receptor de DTV o caja de
conexión con un componente de video
ColorStream® y una videograbadora
Usted necesitará lo siguiente:
• Tres cables coaxiales
Esta conexión le permite mirar DTV (Televisor Digital), la
videograbadora, los programas de televisión y grabar los programas
de DTV y TV.
Su televisor tiene entradas para componente de video ColorStream®.
Al conectar su televisor a un receptor de DTV con un componente de
video podrá mejorar enormemente la calidad de la imagen y el
realismo.
• Dos juegos de cables normales de A/V
• Un par de cables normales de audio
• Un juego de cables componente de video
Nota:
Podrá conectar los cables de composante de
video a cualquier juego de conectores
ColorStream en la televisor (HD-1 o HD-2).
De la antena
Los conectores HD-1 y HD-2 ColorStream y
los conectores HDMI pueden usarse con los
sistemas de exploración Progresiva (480p,
720p) y Entrelazado (480i, 1080i). Una señal
de 1080i proporcionará la mejor
Videograbadora
estereofónica
IN
IN from ANT
OUT to TV
representación de la imagen.
OUT
Si su receptor de DTV no tiene componente
de video, use en lugar de eso, conexiones de
S-video y conexiones normales de audio. No
conecte un cable S-video y un cable normal
de video normal a VIDEO-1 (o VIDEO-2 o
VIDEO-3) al mismo tiempo o la imagen será
inaceptable.
CH
CH
3
4
VIDEO
AUDIO
Panel trasero de la TV
Para la conexión de HDMI, vea la página 13.
La grabación no autorizada, el uso, la
distribución, o la revisión de los
programas televisivos, videos, DVD, y
otros materiales se prohíben bajo las
Leyes de Copyright de los Estados
Unidos y otros países, y usted podría
estar sujeto a la responsabilidad civil y
penal.
De la antena
de DTV
AUDIO
OUT
L
Y
S-VIDEO
COMPONENT VIDEO
VIO
OT
R
Receptor de DTV con componente de video
11
J3W60321A(S)_P07-14
11
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conectando una videocámara
Esta conexión le permite ver los materiales de videos grabados en una
videocámara.
Usted necesitará lo siguiente:
• Un juego de cables normales de A/V
Videocámara
Panel delantero de la TV
Usted necesitará lo siguiente:
• Un cable de S-Video
• Un par de cables normales de audio
Videocámara S-VHS
Nota:
AUDIO
L
S-VIDEO
VIDEO
Para obtener una mejor calidad en la imagen,
si su videocámara tiene S-video, podrá usar
un cable S-video (más los cables normales
de audio) en lugar de un cable normal de
video. No conecte un cable normal de video y
un cable de S-video simultáneamente a
VIDEO1.
R
OUT
Panel delantero de la TV
12
J3W60321A(S)_P07-14
12
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexión de un dispositivo de HDMI™ o DVI
Las entradas de HDHI (High-Definition Multimedia
[1] El cumplimiento EIA/CEA-861/861B cubre la transmisión de
Interface) de su televisor reciben audio digital y video digital
no comprimido de dispositivos de una fuente de HDMI o
video digital no comprimido de dispositivos de una fuente
de Interfaz de Video Digital (Digital Visual Interface, DVI).
video digital no comprimido con la protección del contenido
digital de ancho de banda alto que está estandarizándose
para la recepción de señales de video de alta definición.
Debido a que esta es una tecnología que evoluciona, es
posible que algunos dispositivos no puedan operar
apropiadamente con el televisor.
Esta entrada ha sido diseñada para aceptar material de
programación con Protección de Contenido Digital de alto
ancho de banda (High-bandwidth Digital Content Protection,
HDCP) en forma digital de dispositivos electrónicos para el
consumidor que cumplen con las normas EIA/CEA-861/
861B[1] (tales como las cajas decodificadoras o los
Para asegurarse que el dispositivo HDMI o DVI se reinicie
apropiadamente, se recomienda que siga estos
procedimientos:
• Al encender sus componentes electrónicos, encienda
primero el televisor y luego el dispositivo HDMI o DVI.
• Al apagar sus componentes electrónicos, apague primero
el dispositivo HDMI o DVI y luego el televisor.
reproductores de DVD con salida de HDMI o DVI).
La entrada de HDMI ha sido diseñada para producir mejor
rendimiento con señales de video de alta definición.
Acepta y presenta señales de 480i, 480p, 720p y 1080i.
NUNCA CONECTE ESTETV A UNA COMPUTADORA
PERSONAL (PC). EsteTV no se diseñó para usarse
con una PC.
Para conectar un dispositivo DVI, necesitará lo siguiente:
• Un cable adaptador HDMI a DVI
(Conector HDMI tipo A)
Para conectar un dispositivo HDMI, necesitará:
• Un cable HDMI (conector tipo A)
Para la operación apropiada, la longitud de un cable
adaptador HDMI a DVI no deberá exceder los 9.8 pies
(3m). La longitud recomendada es de 6.6 pies (2m).
Para una operación apropiada, se recomienda en lo posible
que use un cable HDMI tan corto como sea
• Un par de cables normales de audio analógico
posible. No deberá encontrar dificultad si usa un cable
HDMI que sea más corto que 16.4 pies (5m).
Un cable adaptador HDMI a DVI sólo transfiere video. Se
requieren cables de audio analógico separados (vea la
ilustración de abajo).
Los cables HDMI transfieren video y audio. No se requieren
cables de audio analógico separados (vea la ilustración de
abajo).
Debe establecer la configuración de entrada de audio
HDMI a “DVI” en el menú de AUDIO (vea la página 38).
Deberá establecer la configuración de entrada de audio
HDMI a “HDMI” en el menú de AUDIO (vea la página 38).
Dispositivo DVI
Algunos CDV (Video CD) podrían no producir señales de audio
digital. En ese caso, podrá escuchar sonido al conectar los
cables de audio analógico. Si usa cables de audio analógico por
esta razón, necesitará establecer la configuración de entrada de
audio HDMI a “DVI” para escuchar el audio analógico (vea la
página 38).
DVI
OUT
VIDEO
AUDIO
L
R
IN
OUT
Nota: Si conecta un dispositivo HDMI y los cables de audio
analógico, y reproduce el medio con salida de audio digital para
escuchar audio digital, deberá establecer la configuración de
entrada de audio HDMI a “HDMI” (página 38).
Dispositivo HDMI
Panel trasero de la TV
Panel trasero de la TV
HDMI, el logotipo de HDMI y la Interfaz de Multimedia de
Alta Definición son marcas comerciales o marcas
comerciales registradas de HDMI Licencing, LLC.
13
J3W60321A(S)_P07-14
13
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexión de un sistema de audio analógico
Usted necesitará lo siguiente:
• Un par de cables normales de audio
Esta conexión permite utilizar altavoces exteriores junto con un
amplificador exterior de audio para regular el volumen.
Para controlar el audio:
Encienda el televisor y el amplificador estéreo.
Desconecte los altavoces incorporados del televisor (ver “Apagando
los altavoces incorporados” en la página 38).
Nota: Para poder escuchar el sonido cuando se utiliza un amplificador
exterior de audio, el volumen del televisor y del amplificador debe estar
ajustado a un nivel razonable de audición.
Panel trasero de la TV
Amplificador
LINE IN
L
R
Conectando un amplificador A/V con sonido surround digital incorporado
Usted necesitará lo siguiente:
• Un cable digital coaxial
Esta conexión le permite usar un amplificador de audio con sonido
surround digital incorporado y altavoces externos.
• Seis par de cables altavoz
Ver “Seleccionando el format de salida digital” en la página 39.
Nota:
Refiera al manual del propietario del
amplificador de audio también.
Panel trasero de la TV
Altavoz
Altavoz de
graves
frontal
(Derecha)
TV
Altavoz
frontal
(Izquierda)
Altavoz central
Alavoz Surround
(Derecha)
Alavoz Surround
(Izquierda)
Amplificador AV con sonido
surround digital incorporado
Las salidas de COAXIAL DIGITAL AUDIO OUT sólo emiten audio digital com salida en las emisiones digitales con sonido
de difusión digital. Para escuchar un sonido de difusión análogo, enchufe los conectores de audio izquierdo y derecho (L/
R) en las entradas del receptor. Consulte el manual del usuario para determinar la mejor forma de elegir entre las señales
análogas o digitales para su receptor.
14
J3W60321A(S)_P07-14
14
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Usando el control remoto
Nota:
Preparando el control remoto para su uso
Además del funcionamiento de la TV, el mando a distancia puede
manejar la mayoría de los convertidores de TV por cable, receptores de
satélite, grabadores de vídeo, y lectores de DVD, independientemente
de su marca. El mando a distancia es preprogramado para manejar la
mayoría de los receptores de satélite, grabadores de vídeo, y lectores
de DVD de Toshiba. Para controlar un dispositivo que no sea de Toshiba
(o un dispositivo de Toshiba cuyo mando a distancia no haya sido
preprogramado para manejar), usted debe programar primero el mando
a distancia. Consulte “Programand el control remoto para operar otros
aparatos”, en la siguiente página.
El control remoto del televisor prodría no operar
su videograbadora, reproductor de DVD o
convertidor de cable TV. Refiérase al manual del
propietario proporcionado con el equipo
respectivo para ver qué funciones podrían estar
disponibles. Adicionalmente, el control remoto
para este televisor prodría no desempeñar
ciertas funciones disponibles en los controles
remotos originales para tal equipo adicional, en
cuyo caso, se sugiere que use el control remoto
original para el aparato respectivo.
Instalando las baterías del control remoto
Para instalar las baterías:
1. Abra la tapa de baterías en la parte de atrás del control remoto.
Precaución:
• Nunca arroje las baterías al fuego.
Nota:
• Esté seguro de usar baterías “AAA”.
• Disponga de las baterías en una área de
disposición designada.
•
Las baterías siempre deben desecharse
teniendo en cuenta el medio ambiente.
Siempre deseche las baterías de acuerdo a
las normas y regulaciones pertinentes.
2. Instale dos baterías de tamaño “AAA”. Haga corresponder los
signos de + y - en las baterías con los signos del compartimiento
de baterías.
•
•
Si el control remoto no funciona
correctamente, o si el rango de operación se
reduce, reemplace las baterías por nuevas.
Si las baterías no tienen carga o si dejará de
usar el control remoto por un tiempo
prolongado, sáquelas. Eso evitará la fuga de
ácido al compartimiento de las baterías.
3. Cierre la tapa de la batería en el control remoto hasta que el cierre
haga un chasquido.
Usando el control remoto para operar otros aparatos
Para controlar a un
convertidor de cable/
receptor satelital:
Para controlar a una
videograbadora:
Power
Input (TV)
Mute (TV)
Channel
Numbers
Input (TV)
Power
Channel
Numbers
Programe el control
remoto para que
Programe el control
remoto para que
reconozca la marca de su
convertidor/receptor
satelital (vea
“Programando el control
remoto para operar otros
aparatos” en la siguiente
página). Los botones
mostrados a la derecha
controlarán el convertidor
de cable/receptor satelital.
Presione primero el botón
de “CBL/SAT”.
reconozca la marca de
su videograbadora (vea
“Programando el control
remoto para operar
otros aparatos” en la
siguiente página). Los
botones mostrados a la
derecha controlarán
luego la
CH RTN
(Channel Return)
VCR
CH RTN
(Channel Return)
Channel
/
CBL/SAT
Volume +/– (TV)
Pic Size (TV)
Channel
/
Volume +/– (TV)
Pic Size (TV)
videograbadora.
Presione primero el
botón de “VCR”.
VCR controls
TV/VCR
15
J3W60321A(S)_P15-22
15
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Para controlar a un
reproductor de DVD:
Power
Input (TV)
Recall
Mute (TV)
Number
buttons
Programe el control
remoto para que
reconozca la marca de
su reproductor de DVD
(vea “Programando el
control remoto para
operar otros aparatos”
debajo). Los botones
mostrados a la derecha
controlarán luego el
reproductor de DVD.
Presione primero el
botón de “DVD”.
Volume +/– (TV)
DVD
Pic Size (TV)
DVD MENU
▲▼
ENTER
DVD controls
DVD Skip/Search
/
TOP Menu
DVD Clear
Programando el control remoto para operar
otros aparatos
Power
Recall
Este control remoto está preprogramado para operar receptores
satelitales, videograbadoras y reproductores de DVD Toshiba. Para
controlar receptores satelitales, videograbadoras, reproductores de
DVD, o convertidores de cable TV diferentes a los modelos de Toshiba,
usted deberá seguir los pasos de abajo para programar su control
remoto.
Channel
Numbers
TV
VCR
DVD
1. Refiérase a Puede agregar los canales en forma manual (ver
“Agregado y borrado manual de canales,” abajo. (en las páginas
17 y 18) para encontrar el código correspondiente para su marca.
Si se lista más de un código, pruebe cada uno separadamente
hasta que encuentre aquel que trabaje.
CBL/SAT
2. Si está programando el control remoto para operar lo siguiente:
• Convertidor de Cable TV/Receptor Satelital: Presione “CBL/SAT.”
• Videograbadora: Presione “VCR.”
• Reproductor de DVD: Presione “DVD.”
3. Mientras retiene RECALL, presione los botones de números para
los canales e ingrese el código de tres dígitos para su aparatos.
Nota: Si no ingresa el código dentro de 10 segundos del paso 3 o
si ingresa un código que no esté listado debajo, esta
operación se cancelará.
Nota:
4. Apunte el control remoto al dispositivo y presione POWER para
probar el código.
• Cuando se envía de la fábrica, el control
remoto se configura para que opere su
televisor.
• Cada vez que reemplace las baterías, deberá
reprogramar el control remoto.
• Algunas videograbadoras más nuevas son
capaces de trabajar en cualquiera de los dos
códigos del control remoto. Estas
videograbadoras tienen un interruptor
etiquetado “VCR1/VCR2. “
• Si el Convertidor de Cable TV/Receptor Satelital,
Videograbadora o Reproductor de DVD responde, ingresó el
código correcto.
• Si el Convertidor de Cable TV/Receptor Satelital,
Videograbadora o Reproductor de DVD no responde, repita los
pasos del 1 al 4 usando otro código.
5. Presione “TV” para controlar la televisor.
Si su videograbadora tiene este tipo de
interruptor y no responde a ninguno de los
códigos para su videograbadora, fije el
interruptor a la otra posición (VCR1 o VCR2)
y reprograme el control remoto.
Para futura referencia, apunte los códigos que usó:
El código del convertidor de cable/receptor satelital_______________
El código de la videograbadora_______________________________
El código del reproductor de DVD_____________________________
16
J3W60321A(S)_P15-22
16
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Tablas de código de dispositivos
[Para el modo de CBL/SAT]
Caja de cable
Marca
Código
Marca
Código
Marca
Código
Satélite
Marca
Código
Marca
Código
Marca
Código
[Para el modo de VCR]
Videograbadora
Marca
Código
Marca
Código
Marca
Código
17
J3W60321A(S)_P15-22
17
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
[Para el modo de VCR]
Videograbadora (continuación)
Marca
Código
Marca
Código
Marca
Código
TV/VCR Combo
Marca
Código
Marca
Marca
Código
Código
Marca
Marca
Código
Código
[Para el modo de DVD]
DVD
Marca
Código
DVD portátil
Marca
Código
Código
Marca
Marca
Código
Código
Marca
Marca
Código
Código
HTIB
Marca
[Para el modo de VCR y DVD]
Conjunto de DVD/VCR
Marca
Código de VCR
Código de DVD
Marca
Código de VCR
Código de DVD
18
J3W60321A(S)_P15-22
18
27/2/06, 9:58 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Aprendiendo sobre el control remoto
TV/VIDEO selecciona la fuente de entrada del video (página 28)
RECALL despliega la información del estado de la TV en pantalla
(página 40)
MUTE apaga el sonido (página 37)
POWER enciende y apaga la televisor
CHANNEL NUMBERS permite el acceso directo a los canales (página 22)
CH RTN (Channel Return) regresa al último canal visto (página 22)
TV selecciona el modo de televisor
TV/Video
Recall
POWER
Mute
Channel
Numbers
CBL/SAT selecciona el modo de videograbadora (página 15)
CH RTN
CH
/
hace los ciclos a través de los canales programados
(channel Return)
(página 21)
Channel
/
Volume +/–
TV
VOL + / – ajusta el nivel del volumen
VCR selecciona el modo de CABLE (página 15)
DVD selecciona el modo de DVD (página 16)
VCR
CBL/SAT
Sleep
DVD
Picture Size
SLEEP programa la televisor para que se apague en una hora
FAV ▲/▼
establecida (página 36)
Menu/Enter
DVD Menu
PIC SIZE hace los ciclos por los cinco tamaño la imagen (página 30)
Enter
Exit
Play
Stop
MENU/ENTER permite el acceso a los menús de programación, y fija
Pause
la información programada del menú (página 20)
Skip/Search
4 ¢
▲▼
selecciona o regula los menús en la pantalla (página 20)
Rew
TOP Menu
FF
TV/VCR
FAV ▲/ ▼ (Canales favoritos) hace ciclos a través de los canales
favoritos (página 22)
Clear
Rec
EXIT cierra los menús en pantalla (página 20)
DVD MENU accede al menú de DVD
ENTER configura la selección del menú en el modo DVD
PAUSE pone en pausa una videocinta o DVD
PLAY reproduce una videocinta o DVD
STOP detiene una videocinta o DVD
SKIP/SEARCH
Controla los saltos en el capítulo del DVD
Alcance efectivo del control remoto
REW rebobina/invierte una cinta de video/DVD.
FF avanza una videocinta o DVD
• Apunte el control remoto al sensor del
televisor (ver la figura) y presione los
botones para operar el equipo.
TOP MENU accede al menú de DVD TOP
REC comienza la grabación de una videocinta
CLEAR limpia los datos de entrada en el modo de DVD
• Opere el control remoto dentro de un
ángulo 30 grados de cualquier lado del
sensor del remoto, hasta una distancia
de aproximadamente 16 ft. (5m).
TV/VCR cambia entre los modos de televisor y videograbadora
cuando se vean mientras se esté grabando
Sensor
del
Remoto
Aprox. 5 metros
19
J3W60321A(S)_P15-22
19
27/2/06, 9:59 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Configurando su televisor
Después que haya instalado las baterías y haya programado el control remoto,
necesitará establecer algunas preferencias en la televisor que usa el sistema
de menú. Podrá acceder al sistema de menú con los botones en el control
remoto.
•
•
•
Cuando haga una selección del menú, sus cambios ocurrirán
inmediatamente. No tendrá que presionar MENU o EXIT para ahorrar sus
cambios.
Después de 15 segundos, la pantalla del menú se cerrará
automáticamente si no hace una selección. Sus cambios todavía se
guardarán.
Cuando haya terminado de programar los menús, presione EXIT.
Empezando configuración
POWER
La función de EMPEZANDO CONFIGURACION aparecerá la primera vez que
encienda el televisor, y le ayudará a seleccionar el idioma del menú,
especificar la configuración de TV/CABLE, y programar los canales
automáticamente.
IMPORTANTE: Debe primero conectar un sistema de antena o cable TV.
Vea “Conectando su TV” en las páginas 7 a 14 para obtener detalles.
1. Presione POWER y encienda el
televisor. La función STARTING SETUP
comenzará y aparecerá el menú de
configuración del idioma en la pantalla.
Presione ▲ o ▼ para seleccionar su
Menu/Enter
idioma deseado, presione ENTER.
2. Presione ▲ o ▼ para seleccionar TV o
CABLE, luego presione ENTER.
3. Presione ▲ o ▼ para seleccionar COMIENZO (START), y luego presione
ENTER, que comienza el INSTALACIÓN AUTOMÁTICA (AUTO SETUP).
Nota: Para cancelar la instalación y volver a la pantalla de TV
normal, presione ▲ o ▼ para seleccionar CANCELAR (CANCEL)
y luego ENTER.
Exit
4. Cuando la INSTALACIÓN AUTOMÁTICA esté completa, aparecerá la
pantalla de TV normal.
Nota:
• La INSTALACIÓN AUTOMÁTICA de canales puede tomar entre 15 y 30
minutos, para completarse, dependiendo de su servicio de cable regional.
• Para cancelar la INSTALACIÓN AUTOMÁTICA y volver a la pantalla de
TV normal, presione SALIR (EXIT).
Cambiando el idioma de despliegue en la
pantalla
Podrá escoger en la pantalla tres idiomas diferentes (inglés, francés,
español) para el despliegue en pantalla de los menús de ajuste y los
mensajes.
Para seleccionar un idioma haga lo siguiente:
1. Presione MENU, luego presione
COLOCAR.
o
para desplegar el menú de
Nota:
La posición y el tamaño de los menús en
pantalla puede cambiar en el caso de
algunos formatos de programa (tales como
los de 1080i o 720p).
COLOCAR
IDIOMA
ESPAÑOL
CABLE
AJUSTE RELOJ
TV/CABLE
CAN PROGRAMA
ANAD/BORRADO
:SELECCIÓN
:AJUSTAR
2. Presione ▲ o ▼ para resaltar IDIOMA.
COLOCAR
IDIOMA
ESPAÑOL
ENGLISH/FRANÇAIS/ESPAÑOL
AJUSTE RELOJ
TV/CABLE
CAN PROGRAMA
ANAD/BORRADO
CABLE
:SELECCIÓN
:AJUSTAR
3. Presione
o
para resaltar su idioma deseado.
20
J3W60321A(S)_P15-22
20
27/2/06, 9:59 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Corrección de inclinación de la imagen
Cuando instale o cambie la dirección de la televisor, la imagen podrá
inclinarse (causado por el magnetismo de la Tierra). Si esto pasa, use
la función de corrección de inclinación de la imagen para obtener la
mejor imagen posible.
Para ajustar la inclinación de la imagen:
1. Presione MENU, luego presione
COLOCAR
o
para desplegar el menú de
Channel
Numbers
CORRE TILT
MEDIDOR DE SEÑAL
0
COLOCAR.
2. Presione ▲ o ▼ para resaltar
CORRETILT.
:SELECCIÓN
:AJUSTAR
3. Presione
o
ajuste la inclinación
de la imagen (de -10 a 10).
Channel
/
Agregando canales a la memoria de el televisor
Cuando presione CHANNEL ▲ / ▼ en la TV o CH
/
en el control
remoto, su televisor sólo se detendrá en los canales que usted haya
guardado en la memoria del canal de canales del televisor. Siga los
pasos de abajo para programar los canales en la memoria.
Programando los canales automáticamente
Su televisor podrá detectar automáticamente todos los canales activos
y podrá guardarlos en su memoria. Después que la televisor haya
guardado automáticamente los canales en su memoria, podrá agregar
o borrar canales específicos manualmente.
Menu/Enter
Exit
Para agregar los canales automáticamente:
1. Presione MENU, luego presione
COLOCAR.
o
para desplegar el menú de
2. Presione ▲ o ▼ hasta que la
selección de TV/CABLE se resalte.
COLOCAR
3. Presione
o
para resaltar ya sea
IDIOMA
ESPAÑOL
TV CABLE
AJUSTE RELOJ
/
TV o CABLE, dependiendo de lo que
use. Si usa una antena, escoja TV.
Si usa cable, escoja CABLE.
4. Presioner ▼ para seleccionar CAN
PROGRAMA.
TV
CABLE
/
CAN PROGRAMA
ANAD/BORRADO
:SELECCIÓN
:AJUSTAR
5. Presione
o
inicie la programación del canal. El televisor
automáticamente hará ciclos a través de todos los canales de
televisión o cable (dependiendo de lo que haya seleccionado), y
guardará todos los canales activos en la memoria de canales. Mientras
el televisor esté haciendo ciclos a través de los canales, aparecerá el
mensaje “PROGRAMACIÓN AHORA POR FABAR ESPERA”.
6. Cuando la programación de canales se haya completado,
aparecerá el mensaje “COMPLETADO”.
Nota:
Puede agregar los canales en forma manual
(vea “Agregado y borrado manual de ca-
nales,” abajo.
7. Presione CH
o
para ver los canales programados.
Agregado y borrado manual de canales
Después que haya programado los canales automáticamente, podrá
agregar o borrar los canales específicos manualmente.
Para agregar o borrar los canales manualmente, haga lo siguiente:
1. Presione MENU, y luego presione
o
para desplegar el menú de
COLOCAR.
COLOCAR
IDIOMA
ESPAÑOL
CABLE
2. Presione ▲ o ▼ para resaltar
ANAD/BORRADO.
AJUSTE RELOJ
CABLE
TV
/
CAN PROGRAMA
ANAD/BORRADO
3. Presione
o
para desplegar el
menú de ANAD/BORRADO.
4. Presione ▲ o ▼ para seleccionar
ANAD/BORRADO, luego presione
:SELECCIÓN
:AJUSTAR
.
5. Presione ▲ o ▼ para seleccionar el canal que desea agregar o
borrar. Presione para seleccionar ANAD o BORRADO,
o
dependiendo de la función que quiera realizar.
6. Repita el paso 5 para añadir o eliminar más canales y, a
continuación, presione ENTER.
7. Presione EXIT para regresar a la vista normal.
Para agregar un canal digital que esté sintonizando:
Seleccione el canal que desee agregar. Presione ▲ o ▼ para
seleccionar AÑADIENDO CANAL en el paso 4, luego presione
.
Para borrar todo canal de la memoria del canal:
Presione ▲ o ▼ para seleccionar ELIMINAR TODO del paso 4 de
arriba, luego presione . Todo canal es borrado de la memoria del
canal. (Puede seguir utilizando los botones de números de los canales
en el mando a distancia para sintonizar un canal.)
21
J3W60321A(S)_P15-22
21
27/2/06, 9:59 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Cambiando los canales
Para cambiar al siguiente canal programado, haga lo siguiente:
Presione CHANNEL ▲/▼ en el televisor o CH
remoto.
o
en el control
Nota:
Para cambiar a un canal analógico específico:
Los canales digitales de su servicio de televisión
por cable pudieran estar representados por
números de canal que incluyen un “guión”
(ejemplo, 85–002). Estos números de canales
digitales pudieran no concordar con los
números de canales proveídos por su servicio
local de televisión por cable. Esto no indica falla
alguna.
Presione los botones de números para los canales (Del 0 al 9) en el
control remoto.
Por ejemplo, para seleccionar el canal 125, presione 1, 2, 5.
Para cambiar a un canal digital específico:
Presione los primeros 3 dígitos, luego presione la tecla con guión
(100/–), seguido por los 3 dígitos restantes.
Por ejemplo, para seleccionar el canal 015-001, presione 0, 1, 5,
Guión, 0, 0, 1.
Usando las funciones de el televisor
Ajustando la configuración de los canales
Cambiando entre dos canales
Podrá cambiar entre dos canales sin ingresar un número de canal actual
cada vez.
Channel
Numbers
Para cambiar entre dos canales:
1. Seleccione el primer canal que desee ver.
2. Seleccione un segundo canal usando los botones de números para
CH RTN
Dash (Guión)
los canales (Del 0 al 9, 100).
Channel
/
3. Presione CH RTN. El canal anterior se desplegará.
Cada vez que presione CH RTN, el televisor cambiará de atrás hacia
adelante entre los dos canales. La función CH RTN está disponible para
las fuentes de entrada de video también.
Menu/Enter
Programando sus canales favoritos
FAV
Exit
/
Usted puede prefijar hasta 12 de sus canales favoritos al usar la función de
programación del canal favorito. Debido a que esta función explora sólo a
través de sus canales favoritos, le permitirá saltar a otros canales que
normalmente no ve.
Podrá usar todavía Channel
/
para explorar a través de todos que
haya programado en la memoria de la televisor.
Para programar sus canales favoritos:
1. Seleccione un canal que desee programar como un canal favorito.
2. Presione MENU, luego presione
OPCION.
o
para desplegar el menú de
3. Presione ▲ o ▼ para resaltar CAN
FAVOR.
OPCION
ON/OFF TIMER
CAN FAVOR.
TITULO CANAL
MENU DE VIDEO
OFF
:SELECCIÓN
:AJUSTAR
Nota:
4. Presione
o
para desplegar el
Para volver del menú CAN FAVOR al menú
OPCION, presione ▲ o ▼ para resaltar
MENU OPCION, luego presione
menú de CAN FAVOR. AJUSTE/
DESPEJAR se resaltará.
o
.
5. Presione
o
para resaltar AJUSTE y presione ENTER.
6. Presione EXIT para cerrar la pantalla.
7. Repita los pasos del 1 al 6 para los otros 12 canales.
Para seleccionar sus canales favoritos:
Presione los botones FAV ▲/▼ en el control remoto para seleccionar
sus canales favoritos.
Los botones FAV ▲/▼ no trabajarán hasta que haya programado uno
o más canales favoritos.
22
J3W60321A(S)_P15-22
22
27/2/06, 9:59 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Para eliminar sus canales favoritos:
1. Seleccione un canal que desee eliminar de la memoria de canal
favorito.
2. Presione MENU, luego presione
OPCION.
o
para desplegar el menú de
3. Presione ▲ o ▼ para resaltar CAN FAVOR.
4. Presione para desplegar el menú de CAN FAVOR.
AJUSTE/DESPEJAR se resaltará.
o
Channel
Numbers
5. Presione
o
para resaltar DESPEJAR.
Channel
/
Menu/Enter
6. Presione ENTER hasta que un “0” reemplace el número de canal
que desee borrar.
Exit
7. Presione EXIT para regresar a la vista normal.
8. Repita los pasos del 1 al 7 para los otros canales.
Usando el menú de BLOQUEAR
La función Chip V sólo está disponible para el sistema Chip V
para los EUA. El sistema de V-chip no está soportado sólo por el
sistema canadiense de V-chip.
Podrá impedir que a otros que vean ciertos programas o canales
bloqueándolos al usar la función de Chip V.
Seleccionando una Contraseña
Antes de que pueda usar la función de Chip V para bloquear los
programas y canales, deberá seleccionar una contraseña. La
contraseña que seleccione, impedirá a otros que cambien los límites
de clasificación que usted estableció.
Para seleccionar su contraseña y acceder al menú de CERRAR haga lo
siguiente:
1. Presione MENU, luego presione
o
para resaltar el menú de
CERRAR.
2. Presione ▲ o ▼ para desplegar el modo de entrada de la
contraseña.
CERRAR
----
NUEVO CLAVE
[0-9]:SELECCIÓN
ENTER : AJUSTE
EXIT:FIN
3. Use los botones de números para los canales (del 0 al 9) para
ingresar su contraseña. Si está accediendo al menú de CERRAR
por primera vez, seleccione un número de cuatro dígitos para que
sea su contraseña. Presione ENTER.
CERRAR
NUEVO CLAVE
[0-9]:SELECCIÓN
ENTER : AJUSTE
EXIT:FIN
4. Ingrese la contraseña de nuevo para confirmarla y luego presione
ENTER. El menú de CERRAR aparecerá.
CERRAR
CONFIRMAR CLAVE
[0-9]:SELECCIÓN
ENTER : AJUSTE
EXIT:FIN
23
J3W60321A(S)_P23-29
23
27/2/06, 9:59 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Podrá configurar ahora el menú de CERRAR. Vea “La función del
V-Chip (control paterno)” (debajo), “Bloqueando los canales” (página
25), “Bloqueando la entrada de video” (página 26), “Configurando el
GameTimerTM” (página 26) o “Usando la función de bloqueo del panel
frontal” (página 27).
Recall
Para cambiar su contraseña:
1. Presione MENU, luego presione
Channel
Numbers
o
para desplegar el menú de CERRAR.
2. Presione ▲ o ▼ para desplegar el modo de entrada de la contraseña.
3. Use los botones de números para los canales (del 0 al 9) para ingresar
su contraseña. Presione ENTER. El menú de CERRAR aparecerá.
4. Presione ▲ o ▼ para resaltar NUEVO CLAVE y presione
o
para
desplegar el menú de NUEVO CLAVE.
5. Use los botones de números para los canales (del 0 al 9) para
ingresar un nuevo código. Presione ENTER.
Menu/Enter
6. Ingrese la contraseña de nuevo para confirmarla, y luego presione
ENTER.
7. Presione EXIT para regresar a la vista normal.
Exit
La función del V-Chip (control paterno)
La Asociación de Películas de América (MPAA - Motion Picture Associa-
tion of America) usa un sistema de clasificación para calificar el contenido
de la película. Las estaciones de televisión también emplean un sistema
de clasificación para calificar el contenido de los programas televisivos.
Las clasificaciones películas y televisión trabajan con la función del Chip V
y le permiten bloquear los programas según los límites de clasificación
que usted establezca.
Para usar Chip V para bloquear los programas por clasificación haga lo
siguiente:
1. Presione MENU, luego presione
o
para desplegar el menú de CERRAR.
2. Presione ▲ o ▼ para desplegar el modo de entrada de la contraseña.
3. Use los botones de números para los canales (del 0 al 9) para ingresar su
contraseña. Presione ENTER. El menú de CERRAR aparecerá.
4. Presione ▲ o ▼ para resaltar V-CHIP.
Nota:
• Si se olvida de su contraseña, presione
RECALL cuatro veces en menos de cinco
segundos mientras el televisor esté en el
modo de ingresar la contraseña. Esto le
permitirá restablecer su contraseña.
• Cuando recepciona en su TV una emisión
digital con un nuevo sistema de evaluación,
puede emplear la función FIJAR V-CHIP
(DTV).
• Presione
o
para resaltar ON para
habilitar el bloqueo del programa con
Chip V por clasificación.
CERRAR
V-CHIP
FIJAR V-CHIP
FIJAR V-CHIP (DTV)
ON
/
OFF
• Presione
o
para resaltar OFF para
desactivar el bloqueo del programa con
Chip V por clasificación.
:SELECCIÓN
:AJUSTAR
5. Presione ▲ o ▼ para resaltar V-CHIP
SET. Luego, presione
o
para
desplegar el menú de V-CHIP SET.
6. Presione ▲ o ▼ para resaltar
CLASIFIQUE TV. Luego, presione
CERRAR
V-CHIP
FIJAR V-CHIP
FIJAR V-CHIP (DTV)
ON
o
para desplegar la clasificación deseada.
: CLASIFIQUE TV no está ijado
TV-Y : Todos los niños
OFF
:SELECCIÓN
:AJUSTAR
TV-Y7 : 7 años de edad y más arriba
TV-G : Público general
TV-PG : Guía paterna
TV-14 : 14 años de edad y más arriba
TV-MA : 17 años de edad y más arriba
• Cuando seleccione TV-Y7, TV-PG, TV-14
o TV-MA, presione RECALL para explicar
la clasificación. Presione ▲ o ▼ para
seleccionar la clasificación deseada. Presione
configuración ON o OFF.
o
para seleccionar la
7. Presione ▲ o ▼ para resaltar CLASIF. PELICULA. Luego presione
o
para desplegar el menú de FIJAR CLASIF. Presione ▲ o ▼ para seleccionar
clasificatión deseada, luego presione
o
para seleccionar ON o OFF.
G
: Todas las edades
: Guía paterna
PG
PG-13 : Se sugiere guía paterna
menos de 13 años de edad
R
: Se sugiere guía paterna
cuando se tenga menos de 17
años de edad
NC17 : 17 años de edad y más arriba
X
: Sólo adultos
24
J3W60321A(S)_P23-29
24
27/2/06, 11:49 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Cuando haya terminado de seleccionar las clasificaciones,
presione EXIT para regresar a la vista normal.
Cuando trate de ver un programa con un bloqueo de clasificación,
aparecerá un mensaje que lista las clasificaciones del programa. El
programa todavía podrá verse si presiona MUTE y luego ingrese su
contraseña para pasar por alto el bloqueo temporalmente.
Bloqueando los canales
Con la función BLOQUEO CANAL, puede bloquear el acceso a ciertos
canales. No podrá sintonizar los canales bloqueados a no ser que borre
el ajuste. Puede bloquear hasta 12 canales de TV y 12 canales de TV
por cable.
Mute
Para bloquear los canales:
1. Seleccione un canal que desee bloquear.
Channel
Numbers
2. Presione MENU, luego presione
CERRAR.
o
para desplegar el menú de
3. Presione ▲ o ▼ para desplegar el
Channel
/
CERRAR
modo de entrada de la contraseña.
4. Use los botones de numéros para
los canales (del 0 al 9) para ingresar
su contraseña, luego presione
ENTER. Aparecerá el menú de
CERRAR.
BLOQUEAR
BLOQUEO CANAL
BLOQUEO VIDEO
Menu/Enter
OFF
OFF
OFF
TIEMPO JUEGO
BLOQUEA PANEL
NUEVO CLAVE
:SELECCIÓN
F
:AJUSTAR
Exit
5. Presione ▲ o ▼ para resaltar
BLOQUEO CANAL y presione
para desplegar el menú de
BLOQUEO CANAL.
o
6. Presione
siguiente:
o
para seleccionar lo
• AJUSTE, para fijar el canal como uno para
bloquearse. Luego presione ENTER.
7. Repita los pasos del 1 al 6 para bloquear los otros canales.
Cuando termine de bloquear los canales, presione EXIT para
regresar a la vista normal.
Si intenta sintonizar un canal bloqueado, el televisor no lo desplegará,
pero desplegará el canal no bloqueado más cercano.
Nota:
• Después de programar BLOQUEO
CANAL, cambie los canales antes de
apagar el televisor.
Para desbloquear los canales:
1. Presione MENU, luego presione
o
para desplegar el menú de
CERRAR.
• Para volver del menú BLOQUEO CANAL al
2. Presione ▲ o ▼ para desplegar el modo de entrada de la
contraseña.
3. Use los botones de números para los canales (del 0 al 9) para
ingresar su contraseña, luego presione ENTER. El menú de
CERRAR aparecerá.
menú CERRAR, presione
o
para
resaltar MENU CERRAR, luego presione
o
.
4. Presione ▲ o ▼ para resaltar BLOQUEO CANAL y presione
o
para desplegar el menú de BLOQUEO CANAL.
5. Presione para resaltar DESPEJAR y limpie todos los
o
canales de la lista de los canales bloqueados. Presione ENTER.
6. Presione EXIT para regresar a vista normal.
25
J3W60321A(S)_P23-29
25
27/2/06, 9:59 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Bloqueando la entrada de video
Recall
Con la función de BLOQUEO VIDEO, podrá bloquear las fuentes de
entrada (VIDEO-1, VIDEO-2, VIDEO-3, ColorStream HD-1,
ColorStream HD-2, HDMI) y los canales 3 y 4. No podrá seleccionar
las fuentes de entrada con el botón de TV/VIDEO o los botones de
Channel a menos que limpie la configuración.
TV/Video
Channel
Numbers
Para configurar el bloqueo de video haga lo siguiente:
1. Presione MENU, luego presione
CERRAR.
o
para desplegar el menú de
2. Presione ▲ o ▼ para desplegar el modo de entrada de la
contraseña.
3. Use los botones de numéros para los canales (del 0 al 9) para
ingresar su contraseña, luego presione ENTER. Aparecerá el
menú de CERRAR.
Menu/Enter
4. Presione ▲ o ▼ para resaltar BLOQUEO VIDEO.
5. Presione
o
para seleccionar uno de lo siguiente:
Exit
• VIDEO: Bloquea VIDEO-1,
VIDEO-2, VIDEO-3 y
CERRAR
ColorStream HD-1, ColorStream
HD-2, HDMI.
• VIDEO +: Bloquea VIDEO-1,
VIDEO-2, VIDEO-3, ColorStream
HD-1, ColorStream HD-2, HDMI,
BLOQUEAR
BLOQUEO CANAL
BLOQUEO VIDEO
OFF
VIDEO
OFF
OFF
/
/
VIDEO+
TIEMPO JUEGO
OFF
BLOQUEA PANEL
NUEVO CLAVE
:SELECCIÓN
F
:AJUSTAR
canal 3 y canal 4. Esta opción deberá usarse si usa la terminal
de la antena para reproducir una videocinta.
6. Presione EXIT para regresar a la vista normal.
Nota:
Después de programar BLOQUEO VIDEO,
cambie los canales o presione la tecla de TV/
VIDEO antes de apagar el televisor o será
bloqueado la próxima vez que lo encienda.
Para desbloquear las entradas de video:
Presione OFF en el paso 5, sobre el cual se desbloquean todas las
fuentes de ingreso de video y los canales 3 y 4.
Configurando el GameTimerTM (Tiempo de juego)
Con la función de GameTimerTM, podrá automáticamente activar la
función de BLOQUEO VIDEO (configuración de VIDEO) para fijar un
límite de tiempo para reproducir un juego de video (30, 60, 90 ó 120
minutos).
Para configurar el cronómetro del juego, haga lo siguiente:
1. Presione MENU, luego presione
CERRAR.
2. Presione ▲ o ▼ para desplegar el modo de entrada de
contraseña.
o
para desplegar el menú de
Nota:
• Puede disfrutar de este televisor también
con videojuegos. No obstante, ciertos
videojuegos que emplean palancas de
control del tipo “pistolas de luz” para
disparar contra objetivos en la pantalla,
pueden no funcionar con este televisor .
3. Use los botones de numéros para los canales (del 0 al 9) para
ingresar su contraseña, luego presione ENTER. Aparecerá el
menú de CERRAR.
4. Presione ▲ o ▼ para resaltar
TIEMPO JUEGO.
CERRAR
5. Presione
o
para seleccionar un
• Para visualizar la función GameTimer,
presione RECALL (ver “Desplegando la
información del estado de la TV en
pantalla” en la página 40).
BLOQUEAR
BLOQUEO CANAL
BLOQUEO VIDEO
OFF
OFF
límite de tiempo (30 minutos, 60
minutos, 90 minutos, 120 minutos u
OFF).
TIEMPO JUEGO
OFF
F
/
30
/
60
/
90
/
120
OFF
BLOQUEA PANEL
NUEVO CLAVE
:SELECCIÓN
:AJUSTAR
6. Presione EXIT para regresar a la
vista normal. Después que se programe GameTimer, el
despliegue aparecerá brevemente cada diez minutos para
recordarle que el GameTimer está operando. Cuando el tiempo
programado se alcance, el despliegue cambiará el canal
automáticamente y entrará a modo de bloqueo de video.
Para desactivar GameTimer y desbloquear el BLOQUEO VIDEO:
Fije BLOQUEO VIDEO a OFF (vea “Bloqueando la entrada de
video” citado anteriormente).
26
J3W60321A(S)_P23-29
26
27/2/06, 9:59 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Panel frontal de la TV
Usando la función de bloqueo del panel frontal
Podrá bloquear los botones del panel frontal para prevenir que sus
configuraciones sean cambiadas accidentalmente (por los niños, por
ejemplo). Cuando el bloqueo del panel frontal esté en ON, todos los
botones de control en el panel frontal de la televisor (excepto POWER) no
operarán.
Para bloquear el tablero frontal:
1. Presione MENU, luego presione
CERRAR.
2. Presione ▲ o ▼ para desplegar el modo de entrada de la contraseña.
3. Use los botones de números para los
Botones que se pueden bloquear
o
para desplegar el menú de
Panel frontal de la TV
canales (del 0 al 9) para ingresar su
contraseña, luego presione ENTER.
El menú de CERRAR aparecerá.
CERRAR
BLOQUEAR
BLOQUEO CANAL
BLOQUEO VIDEO
OFF
OFF
4. Presione ▲ o ▼ para resaltar
BLOQUEO PANEL F y presione
para resalter ON.
TIEMPO JUEGO
ON
/
OFF
BLOQUEA PANEL
NUEVO CLAVE
:SELECCIÓN
F
o
:AJUSTAR
VOLUME
5. Presione EXIT para regresar a la
vista normal.
Si se presiona un botón en el panel frontal (que no sea POWER),
aparecerá el mensaje “NO DISPONIBLE”.
Para desbloquear el tablero frontal:
Recall
Presione y retenga el botón VOLUME ▼ en el panel frontal de el
televisor durante aproximadamente 10 segundos hasta que aparezca el
mensaje “BLOQUEA PANEL: OFF” en pantalla.
Channel
Numbers
También podrá desbloquear el panel frontal al usar los menús:
Seleccione OFF del paso 4 de arriba.
Channel
/
Creando las etiquetas de los canales
Menu/Enter
Las etiquetas del canal aparecen sobre el despliegue del número del
canal cada vez que encienda el televisor, seleccione un canal, o
presiona el botón de RECALL. Podrá
escoger cualquiera de los cuatro
caracteres para identificar un canal.
Para crear las etiquetas del canal,
haga lo siguiente:
OPCION
ON/OFF TIMER
CAN FAVOR.
TITULO CANAL
MENU DE VIDEO
OFF
Exit
1. Seleccione un canal que desee
etiquetar.
:SELECCIÓN
:AJUSTAR
2. Presione MENU, luego presione
o
hasta que el menú de
OPCION aparezca.
3. Presione ▲ o ▼ para resaltar
TITULO CANAL.
TITULO CANAL
:
CAN
4
Para borrar las etiquetas del canal, haga lo
siguiente:
AJUSTE
LABEL
/
DESPEJAR
–
–
–
–
MENU OPCION
4. Presione
menú de TITULO CANAL
AJUSTE/DESPEJAR se resaltará.
o
para desplegar el
1. Seleccione un canal con una etiqueta.
:SELECCIÓN
ENTER:AJUSTE
:AJUSTAR
EXIT:FIN
2. Presione MENU, luego presione
o
.
hasta que aparezca el menú de OPCION.
3. Presione ▲ o ▼ para resaltar TITULO
CANAL.
5. Presione
AJUSTE.
o
para resaltar
4. Presione
o
despliegue el menú de
6. Presione ENTER para resaltar
LABEL.
TITULO CANAL
AJUSTE
:
CAN
4
TITULO CANAL. AJUSTE/DESPEJAR
se resaltará.
LABEL
7. Presione
o
repetidamente hasta
MENU OPCION
5. Presione
o
resalte DESPEJAR.
que el caracter que desee aparezca
en la pantalla. Presione ENTER.
Nota:
:AJUSTAR
ENTER:AJUSTE
EXIT:FIN
6. Presione ENTER.
7. Repita los pasos del 1 al 6 para borrar
otras etiquetas del canal.
El caracter cambiará como se muestra debajo.
Nota:
Para volver del menú TITULO CANAL al
menú OPCION, presione ▲ o ▼ para resaltar
8. Repita el paso 7 para ingresar el resto de los caracteres.
Si usted deseara un espacio en blanco en el nombre de la
etiqueta, deberá escoger un espacio vacío de la lista de
caracteres; de otra manera, un guión aparecerá en ese espacio.
9. Repita los pasos del 1 al 8 para otros canales. Podrá asignar una
etiqueta a cada canal.
MENU OPCION, luego presione
o
.
10. Presione EXIT para regresar a la vista normal.
27
J3W60321A(S)_P23-29
27
27/2/06, 10:00 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Seleccionando la fuente de entrada de video
Presione TV/VIDEO para ver una señal de otro dispositivo conectado a
su televisor, como una videograbadora o reproductor de DVD. Podrá
seleccionar ANT, VIDEO1, VIDEO2, VIDEO3, ColorStream HD1,
ColorStream HD2 o HDMI, dependiendo qué conectores de entrada
usted usó para conectar sus dispositivos (vea “Conectando su
televisor” en la página 7 al 14).
NUNCA CONECTE ESTE TV A
UNA COMPUTADORA PER-
SONAL (PC). Este TV no se
diseñó para usarse con una PC.
FUENTE SELECCIÓN
0. ANT
1. VIDEO1
2. VIDEO2
3. VIDEO3
4. ColorStream HD1
5. ColorStream HD2
6. HDMI
/0-6:SELECCIÓN
Al presionar TV/VIDEO en el
control remoto, se desplegará la
fuente de señal actual. (Presione
TV/VIDEO de nuevo o ▲/▼ o del
0 al 6 para cambiar las fuentes)
Creando las etiquetas de las fuentes de
entrada de video
TV/Video
0-6
La función de etiqueta de video le permitirá etiquetar cada fuente de
entrada para su televisor de la siguiente lista programada de etiquetas:
-
: Usa el nombre de etiqueta predefinido
VCR : Videograbadora
DVD : Video de DVD
DTV : Caja de conexión de televisor digital
SAT
: Caja para el satélite
Menu
Exit
CBL : Caja para el cable
HD
: Dispositivo HDMI (Sólo HDMI)
Para crear etiquetas de las fuentes de entrada de video:
1. Presione MENU, y luego presione
o
para desplegar el menú de
OPCION.
2. Presione ▲ o ▼ para resaltar
MENU DE VIDEO.
3. Presione para desplegar el menú
de MENU DE VIDEO.
4. Presione ▲ o ▼ para resaltar la
fuente de video que desee etiquetar.
MENU DE VIDEO
1.VIDEO1
2.VIDEO2
3.VIDEO3
4.ColorStream HD1
5.ColorStream HD2
6.HDMI
-
-
-
-
-
-
/
VCR
/
DVD
SAT
/
/
DTV
CBL
5. Presione
o
para seleccionar la
etiqueta deseada para esa fuente
de entrada.
MENU OPCION
:SELECCIÓN
:AJUSTAR
6. Presione EXIT para regresar a la
vista normal.
28
J3W60321B(S)_P23-29
28
3/4/06, 6:12 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Configurando el reloj
Deberá ajustar el reloj antes de que pueda programar el cronómetro de
ON/OFF.
Nota:
Si se interrumpe la fuente de energía para el
televisor (por ejemplo, el cable de corriente está
desconectado u ocurre una falla en la energía),
necesitará volver a ajustar el reloj.
Para ajustar el reloj: (Ejemplo: 8:30 AM
Marzo, 25 (SAB), 2006)
1. Presione MENU, luego presione
COLOCAR
IDIOMA
ESPAÑOL
CABLE
AJUSTE RELOJ
TV
o
para desplegar el menú de
/
CABLE
CAN PROGRAMA
ANAD BORRADO
/
COLOCAR.
2. Presione ▲
o
▼ para resaltar
:SELECCIÓN
:AJUSTAR
AJUSTE RELOJ, luego presione
3. Presione para ajustar la
.
Recall
o
MES, luego presione ▼.
4. Fije el DÍA, el AÑO y la HORA
como en el paso 3.
AJUSTE RELOJ
MES
DIA
ANO
HORA
1
1 (DOM)
2006
12:00AM
Después de programar el reloj, la
fecha y la hora comienzan a
funcionar automáticamente.
:SELECCIÓN
:AJUSTAR
EXIT:FIN
5. Presione EXIT para regresar a la vista normal.
Configurando el cronómetro de ENCENDIDO/APAGADO
Esta función le permite a usted programar el televisor para que se
encienda automáticamente en una hora fijada. Si programa ON TIMER
a “DIARIO”, el televisor se encenderá todos los días a la misma hora y
en el mismo canal hasta que elimine ON TIMER.
Menu/
Enter
Para ajustar el cronómetro de encendido: (Ejemplo: Encender el
televisor en el canal 12 a las 7:00 AM, DIARIAMENTE)
1. Ajuste el reloj, si no lo ha hecho todavía (vea arriba).
Exit
2. Presione MENU, luego presione
de OPCION.
o
para despleger el menú
3. Presione ▲ o ▼ para resaltar ON/OFF TIMER.
4. Presione para resaltar
o
AJUSTE, luego presione ENTER.
Aparecerá el menú de ON/OFF
TIMER.
5. Presione ▲ o ▼ para resaltar ON
TIMER y presione para resaltar la
posición de las horas.
6. Presione ▲ o ▼ para ajustar la hora
deseada, luego presione
.
7. Ajuste los minutos y el canal como
se hizo en el paso 6.
Nota:
• Si se interrumpe o falla el suministro de
energía eléctrica, se perderá el ajuste del
cronómetro.
8. Presione
o
para seleccionar la
fecha del cronómetro UNA VEZ o
DIARIO.
9. Presione EXIT para regresar a la vista normal.
•
Para visualizar la función de cronómetro de
Encendido/Apagado presione RECALL (ver
“Desplegando la información del estado de
la TV en pantalla” en la página 40).
Para ajustar el cronómetro (de apagado automático):
• Para volver del menú ON/OFF TIMER al
menú OPTION, presione ▲ o ▼ para
resaltar MENU OPTION, luego presione
Siga los pasos 1 al 9 arriba, excepto
OFF TIME selecta en el paso 5.
ON/OFF TIMER
ON TIMER
6:30AM
CAN
DIARIO
1
o
.
OFF TIMER
12:00AM
DESPEJAR
MENU OPCION
:SELECCI
N
:AJUSTAR
EXIT:FIN
Para cancelar el cronómetro (de encendido automático),
haga lo siguiente:
Presione dos veces para seleccionar DESPEJAR en el paso 4,
arriba.
Presione EXIT para regresar a la vista normal.
29
J3W60321A(S)_P23-29
29
27/2/06, 10:00 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Viendo los formatos de imágenes de pantalla
amplia (Sólo para señales de 480i y 480p)
Podrá ver programas en formato de 480i y 480p en una variedad de
tamaños: Natural, Dimensión Cine1, Dimensión Cine2, Dimensión
Cine3 y Completo.
0-4
La manera en que se despliegue la imagen en cualquiera de los
tamaños de la imagen variará, dependiendo del formato del programa
que esté viendo. Seleccione el tamaño de la imagen que despliega el
programa actual de la manera que le parezca mejor a usted.
Seleccionando el tamaño de la imagen
1. Presione PIC SIZE en el control remoto.
Pic Size
2. Presione el botón del número correspondiente (del 0 al 4) o ▲/▼
para seleccionar el tamaño deseado de la imagen, como se de-
scribe debajo y en la siguiente página.
▲/▼
Nota:
También podrá cambiar el tamaño de la
imagen al seleccionar TAMANO IMAGEN en
el menú de COLOCAR.
Tamaño natural de la imagen
•
La imagen se despliega cerca de su proporción originalmente
formateada. Algunos formatos del programa se desplegarán con
barras laterales y/o barras en la parte superior e inferior.
Ejemplo del tamaño natural de la imagen: La manera en que se
despliegue la imagen variará, dependiendo del formato del
programa que esté mirando actualmente.
Nota:
La función TAMANO IMAGEN no está
disponible para algunos formatos de
programa (tales como 1080i o 720p). Tales
formatos se desplegarán en el tamaño natural
de la imagen.
Imagen convencional (4:3) de
tamaño natural en su televisor de
pantalla amplia
Imagen convencional (4:3)
en una pantalla de televisor
convencional
AVISO DE POSIBLES EFECTOS
ADVERSOS EN EL TUBO DE
IMÁGENES DE LA TELEVISOR
Evite desplegar imágenes estacionarias
en su televisor durante períodos
Tamaño Dimensión Cine1 de la imagen (para programas
con formato 4:3)
extendidos de tiempo. Las imágenes fijas
(que no se mueven) tales como las barras
negras o grises en los formatos de
imágenes de pantalla amplia, los
patrones de juegos de video, los logotipos
de las estaciones de televisor y los
subtítulos ocultos pueden quedar
marcadas permanentemente en el tubo
de imágenes. Este tipo de daño NO SE
CUBRE POR SU GARANTÍA.
•
La imagen se expande de forma
más amplia para llenar el ancho de
la pantalla, pero sólo ligeramente
extendida de forma más alta.
•
Los márgenes superior e inferior
podrían estar ocultos; sin embargo,
este modo no puede desplazarse.
Usar estas funciones para cambiar el
tamaño de la imagen (es decir, cambiar la
proporción de la altura / anchura) para
cualquier otro propósito diferente a su
observación privada podría prohibirse bajo
las Leyes de Copyright de los Estados
Unidos y otros países, y usted podría estar
sujeto a la responsabilidad civil y penal.
Ejemplo del tamaño
Dimensión Cine1 de la
imagen
30
J3W60321A(S)_P30-37
30
27/2/06, 10:00 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Tamaño Dimensión Cine2 de la imagen (para los
programas en “letter-box”)
Nota:
Si selecciona Dimensión Cine2 ó 3, los
márgenes superior e inferior de la imagen
podrán estar ocultos. Para ver los bordes
ocultos, desplace ya sea la imagen (vea la
página 32) o trate de ver el programa en
tamaño Completo de la imagen.
•
La imagen se extiende en la misma
proporción de forma más amplia y
más alta (retiene su proporción
original).
A B C D E F G - - - - - - - - - - - - - - - -
•
Los márgenes superior e inferior de
la imagen podrían estar ocultos.
Para ver las áreas ocultas, vea
“Desplazando la imagen
TheaterWide” en la página 32.
Ejemplo del tamaño
Dimensión Cine 2 de la
imagen
Tamaño Dimensión Cine3 de la imagen (para los
programas en “letter-box” con subtítulos)
•
La imagen se expande de forma
más amplia para llenar el ancho de
la pantalla, pero sólo ligeramente
extendida de forma más alta.
A B C D E F G - - - - - - - - - - - - - - - -
•
Los márgenes superior e inferior de
la imagen podrían estar ocultos.
Para ver las áreas ocultas (como
subtítulos o subtítulos ocultos), vea
“Desplazando la imagen
TheaterWide” en la página 32.
A B C D E F G - - - - - - - - - - - - - - - - - - - - - - - - - -
Ejemplo del tamaño
Dimensión Cine 3 de la
imagen
AVISO DE POSIBLES EFECTOS
ADVERSOS EN EL TUBO DE
IMÁGENES DE LA TELEVISOR
Evite desplegar imágenes estacionarias
en su televisor durante períodos
Tamaño Completo de la imagen (para programas de
fuentes 16:9)
extendidos de tiempo. Las imágenes fijas
(que no se mueven) tales como las barras
negras o grises en los formatos de
imágenes de pantalla amplia, los
patrones de juegos de video, los logotipos
de las estaciones de televisor y los
subtítulos ocultos pueden quedar
marcadas permanentemente en el tubo
de imágenes. Este tipo de daño NO SE
CUBRE POR SU GARANTÍA.
•
Si se recibe un programa en formato
16:9, la imagen se visualiza en su
proporción original.
•
Si está recibiendo un programa con
formato 4:3, la imagen se expandirá
de forma más amplia para llenar la
anchura de la pantalla, pero no se
expandirá de forma más alta.
•
Ninguna de las imágenes se ocultan.
Ejemplo del tamaño
Completo de la imagen
Usar estas funciones para cambiar el
tamaño de la imagen (es decir, cambiar la
proporción de la altura / anchura) para
cualquier otro propósito diferente a su
observación privada podría prohibirse bajo
las Leyes de Copyright de los Estados
Unidos y otros países, y usted podría estar
sujeto a la responsabilidad civil y penal.
31
J3W60321A(S)_P30-37
31
27/2/06, 10:00 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Desplazando la imagen TheaterWide®
(sólo Dimensión Cine2 y 3)
1. Presione PIC SIZE para seleccionar el modo Dimensión Cine2 ó 3.
2. Presione MENU, o manténgalo presionado
aparezca el menú de COLOCAR.
o
hasta que
3. Presione ▲ o ▼ para resaltar EXPLORACIÓN DE IMAGEN.
Pic Size
Menu
4. Presione
o
para desplegar el modo de Ajuste del
Desplazamiento.
AJUSTE DE EXPLORACION
PARA AJUSTAR
0
5. Presione ▲ o ▼ para ajustar la posición vertical de la imagen.
• Posición normal (centro)
AJUSTE DE EXPLORACION
PARA AJUSTAR
0
Nota:
Podrá desplazar la imagen en Dimensión
Cine2 y Dimensión Cine3 solamente. Las
cantidades de desplazamiento son como
siguen:
• Para subir la imagen, presione
▲.
• Fuente de la señal 480i/480p:
Dimensión Cine1: No ajustable
Dimensión Cine2: -10 a +20
Dimensión Cine3: -10 a +10
• Para bajar la imagen, presione
▼.
AJUSTE DE EXPLORACION –10
PARA AJUSTAR
32
J3W60321A(S)_P30-37
32
27/2/06, 10:00 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Seleccionando la modalidad CINEMA
Cuando vea una película en DVD (con proceso desplegable 3:2) del
reproductor de DVD conectado a las entradas del ColorStream (video
componente) en el televisor, podrá obtenerse una película más nítida y
natural al configurar MODO CINE a PELICULA.
Para fijar MODO CINE a PELICULA:
1. Presione MENU, y luego presione
o
hasta que aparezca el menú
COLOCAR
de COLOCAR.
SUBTITULO
OFF
SUBTITULOS AVANZADOS
TAMANO IMAGEN
EXPLORACIÓN DE IMAGEN
2. Presione ▲ o ▼ para resaltar
MODO CINE, y luego presione
MODE CINE
PELICULA/VIDEO
Menu
Exit
:SELECCIÓN
:AJUSTAR
o
seleccione PELICULA.
Para fijar MODO CINE a VIDEO (off):
Seleccione VIDEO en el paso 3 de arriba.
Seleccionando el formato de despliegue
(sólo para señales de 480p)
Esta función convierte una señal de entrada de 480p a 540p o 1080i.
Para seleccionar el formato de despliegue haga lo siguiente:
1. Presione MENU, y luego manténgalo presionado
o
hasta que
aparezca el menú de IMAGEN.
2. Presione ▲ o ▼ para resaltar FORMATO ESCENA.
3. Presione
o
para seleccionar 540p o 1080i.
IMAGEN
CableClear
TEMPERATURA DE
COLOR
FORMATO ESCENA
SVM
RESET
ON
FRIO
540p
ALTO
/
1080i
Nota:
:SELECCIÓN
:AJUSTAR
• La función FORMATO ESCENA sólo está
disponible para una entrada de 480p. 1080i
siempre será la salida cuando una señal
diferente a 480p sea la entrada.
• Si nota parpadeo en una imagen de 480p,
trate de configurar FORMATO ESCENA a
540p.
Ajustando la imagen
Seleccionando la modalidad de la imagen
Podrá seleccionar cuatro modos de imágenes - Deportes, Normal,
Cine, y Memoria -como se describen en la tabla siguiente:
Modalidad Calidad de Imagen
DEPORTES Imagen brillante y dinámica (fijado de fábrica)
NORMAL
CINE
Imagen estándar (fijado de fábrica)
Configuración de la imagen como de película (fijado
de fábrica)
MEMORIA Sus preferencias personales (fijadas por usted; vea
“Ajustando la calidad de la imagen” en la página 34)
Para seleccionar la modalidad de la imagen:
1. Presione MENU, luego presione
IMAGEN.
o
para desplegar el menú de
2. Presione ▲ o ▼ para resaltar MODO.
IMAGEN
MODE
DEPORTES
/
DEPORTES
/
NORMAL
/
CINE
25
50
MEMORIA
BRILLO
CONTRASTE
COLOR
TINTE
NITIDEZ
25
0
25
:SELECCIÓN
:AJUSTASR
3. Presione
o
para resaltar el modo que prefiera.
4. Presione EXIT para regresar a la vista normal.
33
J3W60321A(S)_P30-37
33
27/2/06, 11:48 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Ajustando la calidad de la imagen
Podrá ajustar la calidad de la imagen a sus preferencias personales,
incluyendo el contraste, brillo, color, tinte, y nitidez. Las calidades que
escoja se guardarán automáticamente en la memoria de su televisor para
que pueda hacerlas volver en cualquier momento.
Para ajustar la calidad de la imagen:
1. Presione MENU, luego presione
IMAGEN.
o
para desplegar el menú de
2. Presione ▲ o ▼ hasta que el elemonto que desee ajustar se resalte.
Menu
Exit
IMAGEN
MODO
DEPORTES
BRILLO
CONTRASTE
COLOR
TINTE
NITIDEZ
25
50
25
0
25
:SELECCIÓN
:AJUSTAR
3. Presione
o
para ajustar el nivel.
Presionar
Selección
BRILLO
CONTRASTE
COLOR
más oscuro
más bajo
más pálido más profundo
más claro
más alto
TINTE
rojizo
verdoso
NITIDEZ
más suave
más nítido
4. Presione EXIT para regresar a la vista normal.
Seleccionando la temperatura del color
Cambie la calidad de la imagen al hacer la selección de tres
temperaturas de colores programadas - Frio, Medio y Caliente - como
se describe en la tabla siguiente:
Modos
Calidad de la Imagen
FRIO
MEDIO
CALIENTE
Azulado
Neutral
Rojizo
Para seleccionar el color de la temperatura:
1. Presione MENU, luego presione
o
para desplegar el menú
de IMAGEN.
2. Presione ▲ o ▼ para resaltar TEMPERATURA DE COLOR.
IMAGEN
CableClear
ON
FRIO
FRIO /MEDIO
TEMPERATURA DE
COLOR
/
CALIENTE
FORMATO ESCENA
1080i 1080i
ALTO
SVM
RESET
:SELECCIÓN
:AJUSTAR
3. Presione
o
para resaltar el modo que prefiera.
4. Presione EXIT para regresar a la vista normal.
34
J3W60321A(S)_P30-37
34
27/2/06, 10:00 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Usando la función CableClear®
CableClear® reduce la interferencia visible en su imagen de televisión.
Esto es útil cuando se reciba una transmisión con una señal débil
(sobre todo en un canal de Cable), al reproducir una videocasete o si
el disco se daña por el uso repetido.
Para activar la función de CableClear®:
1. Presione MENU, luego presione
o
para desplegar el menú
de IMAGEN.
2. Presione ▲ o ▼ para resaltar CableClear.
Menu
Exit
IMAGEN
CableClear
TEMPERATURA DE
COLOR
ON
/
OFF
FRIO
FORMATO ESCENA
SVM
1080i
ALTO
RESET
:SELECCIÓN
:AJUSTAR
3. Presione
o
para seleccionar ON.
4. Presione EXIT para regresar a la vista normal.
Para apagar la función de CableClear®:
Seleccione OFF en el paso 3 de arriba.
Seleccionando la Modulación de Velocidad de
la Exploración (SVM - Scan Velocity Modula-
tion)
La función SVM realza el contraste y nitidez de la imagen. Esta función
tiene tres modos: ALTO, BAJO y OFF.
Para seleccionar la función de SVM:
1. Presione MENU, luego presione
o
para desplegar el menú
de IMAGEN.
2. Presione ▲ o ▼ para resaltar SVM.
Nota:
No se requiere SVM al ver algún material de
video de alta calidad. Si está mirando el
material de video de alta calidad, puede
cambiar SVM a OFF.
IMAGEN
CableClear
TEMPERATURA DE
COLOR
ON
FRIO
FORMATO ESCENA
SVM
1080i
ALTO
/
BAJO
/
OFF
RESET
:SELECCIÓN
:AJUSTAR
3. Presione
o
para seleccionar el modo que prefiera.
4. Presione EXIT para regresar a la vista normal.
Para apagar SVM:
Seleccione OFF en el paso 3 de arriba.
Restableciendo sus ajustes de la imagen
La función RESET devuelve los ajustes de calidad de la imagen a las
siguientes configuraciones de fábrica:
Modo ....................... deportes Tinte ........................ centro (0)
Brillo..................... centro (25) Nitidez ................... centro (25)
Contraste ................ max (50) Temperatura de color ......... frio
Color .................... centro (25) SVM ..................................Alto
Para restablecer sus ajustes de la imagen:
1. Presione MENU, luego presione
IMAGEN.
o
para desplegar el menú de
2. Presione ▲ o ▼ para resaltar RESET, y luego presione .
IMAGEN
CableClear
TEMPERATURA DE
COLOR
FORMATO ESCENA
SVM
RESET
ON
FRIO
1080i
ALTO
:SELECCIÓN
:AJUSTAR
35
J3W60321A(S)_P30-37
35
27/2/06, 10:00 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Configurando el cronómetro apagado
automatico (sleep timer)
Podrá configurar la televisor para que se apague automáticamente.
Para ajustar el cronómetro apagado automatico (sleep timer):
Presione repetidamente SLEEP en el control remoto para fijar la
duración de tiempo hasta que la televisor se apague. El reloj hará una
cuenta regresiva de 10 minutos por cada presión del botón SLEEP
(0h00m, 0h10m,...1h50m, 2h00m). Después que el tiempo de dormir
se programe, el despliegue aparecerá brevemente cada diez minutos
para recordarle que el cronómetro de dormir está operando.
Sleep
Para confirmar la configuración del cronómetro apagado
automatico (sleep timer), haga lo siguiente:
Presione SLEEP una vez. El tiempo restante se desplegará
momentáneamente.
Menu/Enter
Para cancelar el cronómetro apagado automatico (sleep timer),
haga lo siguiente:
Presione repetidamente SLEEP hasta que el despliegue cambie a 0h00m.
Exit
Usando la función de subtítulos
La función Closed Caption tiene dos opciones:
•
Desplegar subtítulos en la pantalla de diálogo, narración y efectos
de sonido de los programas y videos que tengan subtítulos
(normalmente identificados como “CC”):
Desplegar texto en la pantalla de información no relacionada al
programa, como el clima o los datos de la bolsa de valores (si está
disponible en su área de vista).
•
Para ver subtítulos o texto:
1. Sintonice el televisor al programa
deseado.
COLOCAR
2. Presione MENU, y luego presione
SUBTÍTULO
OFF
C2 / T1 / T2
Nota Importante:
C1
/
/
OFF
o
para desplegar el menú de
SUBTÍTULOS AVANZADOS
TAMANO IMAGEN
EXPLORACIÓN DE IMAGEN
MODE CINE
Si el texto no está disponible en su
área de vista, aparecerá un rectángulo
negro en la pantalla. Si esto pasa, fije la
función de Subtítulos a OFF.
COLOCAR.
VIDEO
3. Presione ▲ o ▼ para resaltar
SUBTÍTULO.
:SELECCIÓN
:AJUSTAR
4. Presione
o
seleccione el modo deseado de Subtítulos, como sigue:
• Para ver subtítulos, seleccione C1 o C2 (C1 despliega la
traducción del idioma primario en su área).
Nota: Si el programa o video que haya seleccionado no tiene
subtítulos, no se desplegarán subtítulos en la pantalla.
• Para ver texto, seleccione T1 o T2.
Nota:
La función de subtítulos no podrá descifrarse
en las situaciones siguientes:
Nota: Cuándo se recibe una señal digital, usted puede escoger
entre CS1, CS2, CS3, CS4, CS5, CS6, C1, C2, C3, C4, T1, T2, T3,
T4, y OFF.
– Cuando una videocinta se haya doblado.
– Cuando la recepción de la señal esté débil.
– Cuando la recepción de la señal no sea
normal.
Para desactivar la función de Subtítulos:
Resalte OFF en el menú de SUBTÍTULO.
Usando la functión de subtítulos avanzados
Esta función está diseñada para personalizar únicamente el los subtítulos digitales.
1. Sintonice el televisor al programa deseado.
AVISO DE POSIBLES EFECTOS
ADVERSOS EN EL TUBO DE
2. Presione MENU, y luego presione
de COLOCAR.
o
para desplegar el menú
IMÁGENES DE LA TELEVISOR
Evite desplegar imágenes estacionarias
en su televisor durante períodos
3. Presione
▲
o
▼
para resaltar SUBTÍTULOS AVANZADOS, luego presione
.
4. Presione ▲ o ▼ para seleccionar los elementos deseados para
extendidos de tiempo. Las imágenes fijas
(que no se mueven) tales como las barras
negras o grises en los formatos de
imágenes de pantalla amplia, los
patrones de juegos de video, los logotipos
de las estaciones de televisor y los
subtítulos ocultos pueden quedar
marcadas permanentemente en el tubo
de imágenes. Este tipo de daño NO SE
CUBRE POR SU GARANTÍA.
ajustar, luego presione
o
.
5. Presione ▲ o ▼ para seleccionar el ajuste deseado, luego presione ENTER.
Puede seleccionar los siguientes elementos y opciones de
configuración.
Elementos
Opciones
TAMAÑO
SUBTÍTULO:
AUTO, PEQUEÑO, NORMAL, GRANDE
TIPO TEXTO
SUBTÍTULO:
AUTO, PREDETEMINADO, MONO CON LÍNEA DE
PIE, PROP. CON PIE LETRA, MONO SIN LÍNEA
DE PIE, PROP. SIN PIE DE LETRA, INFORMAL,
CURSIVA, MAYÚSCULAS PEQUEÑAS
AUTO, NEGRO, BLANCO, ROJO, VERDE,
AZUL, AMARILLO, MAGENTA, AZUL VERDE
AUTO, NINGUNO, ELEVADO, OPRIMIDO,
UNIFORME, SOMBRA A LA IZQUIERDA,
SOMBRA A LA DERECHA
AUTO, NEGRO, BLANCO, ROJO, VERDE,
AZUL, AMARILLO, MAGENTA, AZUL VERDE
COLOR TEXTO
SUBTÍTULO:
Nota:
No configure el color de texto “COLOR
TEXTO SUBTÍTULO” para subtítulo del mismo
color que el color de fondo “COLOR DE
FOND” ya que esto hará que el texto no sea
visible.
BORDE TEXTO
SUBTÍTULO:
COLOR DE FONDO:
6. Presione EXIT para regresar a la vista normal.
36
J3W60321A(S)_P30-37
36
27/2/06, 10:01 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Ajustando el sonido
Enmudeciendo el sonido
Mute
Presione MUTE para apagar el sonido temporalmente. Mientras que el
sonido esté apagado, la pantalla desplegará la palabra MUDO
(Enmudecido) en la esquina inferior derecha. Para restaurar el sonido,
presione MUTE nuevamente, o VOL +/–.
Recall
Seleccionando las estaciones en estéreo/SAP
El sonido multicanal de televisor (MTS - Multi-channel TV) proporciona
sonido estereofónico de alta fidelidad. MTS también puede transmitir
un segundo programa de audio (SAP - Second Audio Program)
conteniendo un segundo idioma u otra información de audio.
Volume
Menu
Nota: La función MTS no está disponible en el modo de digitale et VIDEO.
Cuando el televisor reciba una transmisión en estéreo o SAP, la
palabra ESTEREO o SAP aparecerá en la pantalla cada vez que
se encienda la televisor, se cambie el canal, o se presione el
botón de RECALL.
Exit
Para escuchar sonido estereofónico:
1. Presione MENU, luego presione
o
para desplegar el menú de AUDIO.
2. Presione ▲ o ▼ para resaltar MTS.
3. Presione
o
para resaltar EST (estéreo).
Nota:
•
En general, podrá dejar su televisor en el modo estéreo porque el
televisor producirá automáticamente el tipo de sonido siendo
transmitido (estéreo o mono).
•
Si el sonido estereofónico es ruidoso, seleccione MONO para
reducir el ruido.
Nota:
Un segundo programa de audio (SAP) sólo
podrá escucharse en aquellas estaciones de
televisión que lo ofrezcan.
Por ejemplo, una estación podría transmitir
música como segundo programa de audio. Si
tiene el modo de SAP activado, verá el
programa actual en la pantalla pero
escuchará música en lugar del programa
normal de audio.
Sin embargo, si tiene el modo de SAP
activado, y la estación que está mirando no
está transmitiendo actualmente un segundo
programa de audio, escuchará el audio
normal de la estación; sin embargo,
ocasionalmente no hay ningún sonido en el
modo de SAP. Si esto pasa, fije la función de
MTS al modo de ESTEREO.
AUDIO
MTS
GRAVE
AGUDO
BALANCE
SONIDO EST.
PARLANTES
HDMI
EST
25
25
/
SAP
/
MONO
0
OFF
ON
HDMI
:SELECCIÓN
:AJUSTAR
4. Presione EXIT para regresar a la vista normal.
Para escuchar el Segundo Programa de Audio (SAP -
Second Audio Program):
1. Presione MENU, luego presione
AUDIO.
2. Presione ▲ o ▼ para resaltar MTS.
3. Presione
producirán el segundo programa de audio en lugar del audio
normal.
4. Presione EXIT para regresar a la vista normal.
o
para desplegar el menú de
o
para resaltar SAP. Los altavoces de el televisor
Ajustando la calidad del sonido
Podrá cambiar la calidad del sonido de su televisor al ajustar los bajos,
los agudos y el balance.
Para ajustar la calidad del sonido, haga lo siguiente:
1. Presione MENU, luego presione
AUDIO.
o
para desplegar el menú de
2. Presione ▲ o ▼ para resaltar el
elemento que desee ajustar.
3. Presione
nivel.
Nota:
AUDIO
MTS
GRAVE
AGUDO
BALANCE
SONIDO EST.
PARLANTES
HDMI
ESTEREO
o
para ajustar el
25
25
La calidad del sonido de los conectores
variables de audio OUT no son afectados por
los ajustes hechos en los graves, en los
agudos o en el balance.
0
OFF
ON
HDMI
•
hace que la calidad
seleccionada del sonido sea más
débil o que disminuya el balance
:SELECCIÓN
:AJUSTAR
en el canal izquierdo, dependiendo del elemento seleccionado.
hace que la calidad seleccionada del sonido sea más fuerte
o que disminuya el balance en el canal derecho, dependiendo
del elemento seleccionado.
•
37
J3W60321A(S)_P30-37
37
27/2/06, 10:01 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Usando la función de sonido StableSound®
La función de StableSound limita el nivel más alto del volumen para prevenir
cambios extremos en el volumen cuando se cambie la fuente de señal.
Para encender la función de StableSound®, haga lo siguiente:
1. Presione MENU, luego presione
menú de AUDIO.
o
hasta que aparezca el
2. Presione ▼ o ▲ para resaltar SONIDO EST..
3. Presione
o
para resaltar ON.
AUDIO
MTS
GRAVE
AGUDO
ESTEREO
25
25
0
BALANCE
SONIDO EST.
PARLANTES
HDMI
ON
ON
HDMI
/
OFF
Menu
Exit
:SELECCIÓN
:AJUSTAR
4. Presione EXIT para regresar a la vista normal.
Para apagar la función de StableSound®, haga lo siguiente:
Resalte OFF del paso 3 de arriba.
Apagando los altavoces incorporados
Use esta función para apagar los altavoces de el televisor cuando
conecte un sistema de audio (vea “Conexión de un sistema de audio
analógico” en la página 14).
Para apagar los altavoces incorporados:
1. Presione MENU, luego presione
AUDIO.
o
despliegue el menú de
2. Presione ▲ o ▼ para resaltar PARLANTES.
AUDIO
MTS
GRAVE
ESTEREO
25
25
AGUDO
BALANCE
SONIDO EST.
PARLANTES
HDMI
0
OFF
ON
HDMI
/
OFF
:SELECCIÓN
:AJUSTAR
3. Presione
o
para resaltar OFF.
4. Presione EXIT para regresar a la vista normal.
Para encender los altavoces incorporados
Seleccione ON del paso 3 de arriba.
Seleccionando la fuente de entrada de audio HDMI™
En la sección “Conexión de un dispositivo de HDMI™ o DVI” de la
página 13 hay información sobre conexión.
Si conecta un dispositivo DVI, para escuchar audio también deberá conectar
los cables de audio analógico a los conectores IN de audio (vea la página 13).
Fije la configuración de entrada de audio HDMI a “DVI” con esta conexión.
Si conecta un dispositivo HDMI y reproduce el medio con salida de audio
digital, para escuchar audio digital, fije la entrada de audio HDMI a “HDMI”
con esta conexión.
Si conecta un dispositivo HDMI pero reproduce el medio con salida de audio
analógico (por ejemplo, ciertos CDVs no producirán audio digital), para
escuchar audio, deberá conectar los cables de audio analógico a los
conectores IN de audio HDMI (vea la página 13). Fije la configuración de
entrada de audio HDMI a “DVI” con esta conexión.
Para seleccionar la fuente de entrada de audio HDMI:
1. Presione MENU, y luego presione
de AUDIO.
o
para desplegar el menú
2. Presione ▲ o ▼ para resaltar HDMI.
AUDIO
MTS
GRAVE
STEREO
25
25
AGUDO
BALANCE
SONIDO EST.
PARLANTES
HDMI
0
OFF
ON
HDMI
/
DVI
:SELECCIÓN
:AJUSTAR
3. Presione
o
para seleccionar HDMI o DVI.
4. Presione EXIT para regresar a la vista normal.
38
J3W60321A(S)_P38-Back
38
27/2/06, 10:01 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Usando la función de sonido BBE®
Al corregir la demora de la fase y la distorsión naturalmente generada
por los sistemas de bocinas, la función de sonido BBE* asegura que el
sonido que llega a sus oídos sea tan natural como el sonido original. Las
voces humanas son más claras y la música es natural y bien definida.
Nota:
Asegúrese que el control del volumen de su
amplificador de audio se fije a un nivel de
audición moderado.
Para encender la función de sonido BBE:
1. Presione MENU, luego presione
menú de AUDIO.
o
hasta que aparezca el
2. Presione ▲ o ▼ para resaltar BBE.
3. Presione
o
para resaltar ON.
AUDIO
BBE
IDIOMA AUDIO
ON
/
OFF
FORMATO DE SALIDA
PCM
RESET
:SELECCIÓN
:AJUSTAR
4. Presione EXIT para regresar a la vista normal.
Para apagar la función de sonido BBE:
Resalte OFF del paso 3 de arriba.
Menu
Exit
* Licenciado de BBE Sound, Inc. sobre el numero USP5510752 y 5736897.
BBE y el simbolo de BBE son marcas registradas de BBE Sound, Inc.
Selección de idioma del audio
Si una señal digital incluye dos o más idiomas de audio, puede
seleccionar cuál desea escuchar.
Para selección del idioma del audio:
1. Presione MENU, luego presione
AUDIO.
o
para desplegar el menú de
2. Presione ▲ o ▼ para resaltar IDIOMA AUDIO, luego presione
.
AUDIO
BBE
IDIOMA AUDIO
FORMATO DE SALIDA
OFF
PCM
RESET
:SELECCIÓN
:AJUSTAR
3. Presione ▲ o ▼ para seleccionar el idioma deseado, luego
presione ENTER.
4. Presione EXIT para regresar a la vista normal.
Seleccionando el format de salida digital
Cuando conecte un decodificador Dolby** Digital u otro sistema digital de
audio a la salida de audio digital del TV, use esta función para seleccionar
el formato de salida de audio digital (ver en la página 14 “Conectando un
amplificador A/V con sonido surround digital incorporado”).
Para seleccionar el formato de salida digital:
1. Presione MENU, luego presione
o
despliegue el menú de AUDIO.
2. Presione ▲ o ▼ para resaltar FORMATO DE SALIDA.
AUDIO
BBE
IDIOMA AUDIO
FORMATO DE SALIDA
OFF
PCM
/
PCM
DOLBY DIGITAL
RESET
:SELECCIÓN
:AJUSTAR
3. Presione ▲ o ▼ para resaltar PCM o DOLBY DIGITAL.
4. Presione EXIT para regresar a la vista normal.
** Fabricado bajo licencia de Dolby Laboratories. Dolby y el símbolo de la doble
D son marcas registradas por Dolby Laboratories.
39
J3W60321A(S)_P38-Back
39
27/2/06, 10:01 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Restableciendo sus ajustes de audio
La función de RESET devolverá los ajustes de audio a las
configuraciones de fábrica siguientes:
Recall
Grave .................... Centro (25)
Agudo.................... Centro (25)
Balance ................... Centro (0)
Para restablecer sus ajustes de audio:
1. Presione MENU, luego presione
AUDIO.
o
para desplegar el menú de
2. Presione ▲ o ▼ para resaltar RESET, y luego presione
.
Menu
Exit
AUDIO
BBE
IDIOMA AUDIO
FORMATO DE SALIDA
OFF
PCM
RESET
:SELECCIÓN
:AJUSTAR
Cómo comprobar la potencia de la señal digital
Puede comprobar la potencia de la señal digital mirando el indicador
de señal digital.
Para ver el indicador de señal digital:
1. Presione MENU, luego presione
COLOCAR.
o
para desplegar el menú de
2. Presione ▲ o ▼ para resaltar MEDIDOR DE SEÑAL.
3. Presione
o
para verificar la potencia de la señal digital.
MEDIDOR DE SEÑAL
CANAL(DIGITAL)
1-001
80
Nota:
• La función del indicador de señal no está
disponible en el caso de los canales
analógicos.
• Después de aproximadamente 4 minutos, la
pantalla del medidor de señal cambiará
automáticamente a funcionamiento normal
del televisor.
4. Presione EXIT para regresar a la vista normal.
Desplegando la información del estado de la
TV en pantalla
• Cuando seleccione un canal disponible, el
Presione RECALL para desplegar la siguiente información en la pantalla:
medidor de señal debera de reaccionar.
Canal analógico:
• Reloj
• Número de canal o modo de
VIDEO seleccionado
• Etiqueta del canal (si está
prefijado)
ESTEREO
SAP
PERIOULA
ON TIMER
OFF TIMER
X
12:00AM
12:00PM
DORMIR TIMER 2h00m
TIEMPO JUEGO
Nota:
30m
ANT
ABCD
CABLE
• El estado del canal analógico se mostrará
en la pantalla aproximadamente 4
segundos.
• El estado del canal digital se mostrará en la
pantalla aproximadamente 10 segundos.
Presione RECALL nuevamente, se
mostrará el estado de canal análogo.
• Estado de audio Estéreo o
Segundo Programa de Audio
(SAP - second audio program)
• Clasificación del contenido
• Cronómetro de Encendido/Apagado, GameTimer (Tiempo de
juego), Sleep Timer (si está programado)
• Tamaño de la imagen
NATURAL
007
RELOJ 12:00AM DOM
Canal digital:
• Reloj
• Número de canal, nombre de la
Sun Jan 01 12:00 PM
51-3 Moon Star
CITYHD
estación, nombre del programa
Tiempo Restante 0:20 TV-Y7 Ingres
HD CC
•
•
Tiempo restante
Idioma del audio
Ninguna Information del programa
• Clasificación del contenido
•
•
Marca HD o SD
Marca de subtítulos
• Marca de Chip-V
40
J3W60321A(S)_P38-Back
40
27/2/06, 11:48 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Apagado automático
El televisor se apagará automáticamente después de aproximadamente 15 minutos si se sintoniza en un canal libre o una
estación que termine su transmisión por el día y deje de transmitir en ese canal. Esta función no trabaja en el modo de
VIDEO.
Entendiendo la función de Retorno de Energía
Si la energía se corta mientras esté viendo el televisor y la energía se vuelve a reabastecer, la función de Power Return
encenderá el televisor automáticamente. Si la energía se va a apagar durante bastante tiempo o si usted va a estar
durante bastante tiempo fuera de la televisor, desenchufe el cable de corriente del tomacorriente de la pared para impedir
que el televisor se encienda en su ausencia.
Apéndice
Solución de problemas
Antes de llamar a un técnico de servicio, por favor verifique la tabla por una posible causa del problema y algunas
soluciones.
Problema
Solución
Rectángulo negro en la pantalla
La TV no enciende
• Asegúrese de apagar el menú SUBTÍTULO o apague el modo Texto de subtítulos.
•
•
Asegúrese que el cable de corriente esté conectado, luego presione POWER.
Las baterías del control remoto podrían estar muertas. Reemplace las baterías.
Sin imagen, sin sonido
Sin sonido, imagen bien
• Revise las conexiones de la antena o cable.
• El sonido puede enmudecido. Presione VOLUME.
• La estación podría tener dificultades de transmisión. Pruebe otro canal.
•
La función de MTS podría estar en el modo de SAP. Presione el botón de MTS en el
control remoto hasta que el modo de ESTEREO (o MONO) esté activo.
Sonido pobre, imagen bien
Imagen pobre, sonido bien
• La estación podría tener dificultades de transmisión. Pruebe otro canal.
La función de MTS podría estar en el modo de SAP. Presione el botón de MTS en el
control remoto hasta que esté activo el modo ESTEREO (o MONO).
•
• Verifique las conexiones de la antena.
• La estación podría tener dificultades de transmisión. Pruebe otro canal.
• Ajuste el menú de IMAGEN.
Recepción pobre de los canales de
transmisión
• La estación podrá tener dificultades de transmisión. Pruebe otro canal.
• Verifique las conexiones de la antena.
• Si está usando una videograbadora, asegúrese que el botón de TV/VIDEO esté
configurado correctamente.
No puede recibir por encima del canal 13
Incapaz de seleccionar cierto canal
• Asegúrese que la función de TV/CABLE en el menú de COLOCAR esté fijada al
modo de CABLE.
• El canal podría bloquearse por la función V-Chip o la función de BLOQUEO
CANAL, o borrarse con la función de Add/erase.
No puede acceder a las fuentes de
entrada de la señal (Video-1, Video-2, Video-3,
ColorStream HD-1, ColorStream HD-2, y HDMI)
y/o Canales 3 y 4
• Verifique la función de BLOQUEO VIDEO.
Imágenes múltiples
• La estación podría tener dificultades de transmisión. Pruebe otro canal.
• Use una antena altamente direccional para exteriores.
Color pobre o sin color
• La estación podría tener dificultades de transmisión. Pruebe otro canal.
• Ajuste la opción TINTE y/o COLOR en el menú de IMAGEN.
• Si cambia la dirección de la televisión mientras esté encendida, la imagen podría sufrir
un oscurecimiento del color. En ese caso, apague la televisión y permítale que se
enfríe durante varias horas antes de encenderla de nuevo.
Sin sonido estéreo o SAP de una transmisión MTS • Asegúrese que la función de MTS (en el menú AUDIO) esté
conocida
configurada apropiadamente.
La contraseña del Chip V
No trabaja (Sólo para los sistemas
Chip V de EE.UU.)
• Cambie o restablezca su contraseña.
La control remoto no opera
•
Asegúrese que el modo de TV·CBL/SAT·VCR·DVD esté configurado apropiadamente.
• Remueva todas las obstrucciones entre el control remoto y el televisor.
Las baterías del control remoto podrían estar muertas. Reemplace las baterías.
•
Los botones del panel delantero no opera
• Verifique la función de BLOQUEO PANEL.
Problema en la pantalla por una transmisión digital • Verifique la potencia de la señal digital.
EI área de subtítulo parece no tener texto • Verifique que el color de texto COLOR TEXTO SUBTÍTULO para subtítulo y el
COLOR DE FONDO no estén configurados con el mismo color (vea la página 36)
41
J3W60321A(S)_P38-Back
41
27/2/06, 10:01 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Especificaciones
• Este modelo cumple con las especificaciones de abajo.
• El diseño y las especificaciones están sujetos a cambios sin previo aviso.
• Este modelo tal vez no sea compatible con las funciones y/o especificaciones que puedan agregarse
en el futuro.
Tubo de imagen
26 in. (656.7 mm) diagonalmente
(El tamaño de pantalla es aproximado.)
Sistema de televisión
Cabertura de canales
NTSC estándar, ATSC estándar (8VSB), QAM
VHF: 2 a 13
UHF: 14 a 69
Cable TV: 4A, A-5 a A-1, A-I,
+
+
J–W, W 1 a W 84
Alimentación
120V CA, 60 Hz
Consumo
160 W
Potencìa de audio
Tipo de bocinas
Teminales de Video/Audio
5.0 W + 5.0 W
1-13/16 x 3-7/8 pulg. (45.7 x 99.1 mm) x 2
ENTRADA S-VIDEO
ENTRADA-Y: 1V (p-p), 75 ohmios, sincronización negativa.
ENTRADA-C: 0.286V (p-p) (señal de la ráfaga), 75 ohmios
ENTRADA VIDEO/AUDIO
VIDEO: 1V (p-p), 75 ohmios, sincronización negativa.
AUDIO: 300 mV (rms) (60% modulación equivalente, 35k ohmios)
ENTRADA ColorStream® (video de componente)
Y:
1V (p-p), 75 ohmios
PR: 0.7V (p-p), 75 ohmios
PB: 0.7V (p-p), 75 ohmios
SALIDA AUDIO
300 mV (rms) (60% modulación equivalente, 1k ohmios)
SALIDA DE AUDIO DIGITAL
AUDIO: 0.5 V (p-p), 75 ohmios
ENTRADA HDMI: Cumple con HDMI (conector tipo A)
Cumple con HDCP
Cumple con E-EDID
Velocidades de exploración sugeridas: 1080i, 480p, 480i, 720p
Audio HDMI: De 2 canales
32/44.1/48 kHz Frecuencia de muestreo
16/20/24 bits por muestra
Dimensiones
Ancho: 27-9/16 pulgadas (700 mm)
Fondo: 19-3/4 pulgadas (502 mm)
Alto: 19-1/2 pulgadas (495.5 mm)
Peso
78.3 lbs. (35.5 kg)
Accesorios provistos
Control remoto con dos pilas “AAA”
42
J3W60321A(S)_P38-Back
42
27/2/06, 10:01 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Garantía limitada en los Estados Unidos
Para todos los televisores FST PURE® tipo CRT y televisores de proyección, de 26 pulgadas y más grandes
Toshiba America Consumer Products, L.L.C. (“TACP”) ofrece las siguientes
garantías limitadas al consumidor original de estos televisores en los Estados
Unidos. ESTAS GARANTÍAS LIMITADAS SE EXTIENDEN AL
COMPRADOR/CONSUMIDOR ORIGINAL DE ESTE TELEVISOR, O A
CUALQUIER OTRA PERSONA QUE LO RECIBA COMO REGALO DEL
COMPRADOR/CONSUMIDOR ORIGINAL, Y NO A NINGÚN OTRO
COMPRADOR O CONSUMIDOR.
Sus responsabilidades
LAS GARANTÍAS ANTERIORMENTE MENCIONADAS ESTÁN SUJETAS
A LAS SIGUIENTES CONDICIONES:
(1) Usted deberá conservar su comprobante de compra o proporcionar
alguna otra prueba de la compra.
(2) Todos los servicios de garantía relacionados con este televisor deberán
ser realizados por Centros de Servicio autorizados por TACP.
(3) Las garantías de TACP son válidas solamente si este televisor se compra y se
usa dentro del territorio continental de los Estados Unidos o en Puerto Rico.
LOS TELEVISORES COMPRADOS EN LOS ESTADOS UNIDOS Y
USADOS EN CUALQUIER LUGAR FUERA DE LOS ESTADOS UNIDOS,
INCLUYENDO PERO SIN LIMITARSE AL CANADÁ Y MÉXICO, NO
ESTÁN AMPARADOS POR ESTAS GARANTÍAS.
(4) Estas garantías no se extienden al servicio de mano de obra para instalar
y colocar el televisor o ajustar los controles del cliente, ni por la
instalación o reparación de sistemas de antena. Usted es responsable
por cualquier problema en la recepción causado por un sistema
inadecuado de antena, antenas satelitales mal alineadas, la distribución
de televisión por cable, videograbadoras (VCRs), grabador / reproductor
DVD, dispositivos IEEE-1394 de computadoras personales, y cualquier
otro dispositivo conectado a la fuente de la señal.
(5) Las garantías sólo se extienden a defectos en los materiales o en la
elaboración, conforme se limitan anteriormente, y no a ningún producto o a
piezas que usted haya perdido o descartado; ni por daños al televisor o a sus
piezas ocasionados por incendios, un uso inadecuado, accidentes, fuerza
mayor (tales como relámpagos o fluctuaciones de la energía eléctrica),
instalación inadecuada, mantenimiento inadecuado, uso en violación de las
instrucciones proporcionadas por TACP, mal funcionamiento debido al uso de
este producto simultáneamente con el equipo conectado; a unidades que
hayan sido modificadas o a las cuales se les haya quitado, alterado o borrado
el número de serie, o cuando éste se encuentre ilegible.
LOS TELEVISORES COMPRADOS EN CUALQUIER LUGAR FUERA DE
LOS ESTADOS UNIDOS, INCLUYENDO PERO SIN LIMITARSE AL
CANADÁ Y MÉXICO, Y USADOS EN LOS ESTADOS UNIDOS, NO ESTÁN
AMPARADOS POR ESTAS GARANTÍAS.
Garantía limitada de un (1) año en las piezas y en la mano de obra
TACP garantiza este televisor y sus piezas contra defectos en los materiales o
en la elaboración, por un período de un (1) año contado a partir de la fecha
de la compra original al por menor. DURANTE ESTE PERÍODO DE TIEMPO,
TACP TENDRÁ LA OPCIÓN DE REPARAR O REEMPLAZAR CUALQUIER
PIEZA QUE RESULTE DEFECTUOSA POR PIEZAS NUEVAS O
RECONSTRUÍDAS, SIN CARGO ALGUNO PARA USTED POR LAS
PIEZAS NI POR LA MANO DE OBRA. Cuando sea necesario prestar
servicio de garantía durante este período de tiempo, empleados de un Centro
de Servicio autorizado por TACP vendrán a su casa, y, según el tipo de
reparación necesaria, ellos prestarán ese servicio en su casa o se llevarán el
televisor al Centro de Servicio para repararlo, devolviéndoselo después sin
cargo alguno para usted.
Cómo obtener servicios de garantía
Garantía limitada de dos (2) años en el tubo-pantalla
Si después de seguir todas las instrucciones de funcionamiento incluidas en
este manual y de verificar la sección de solución de problemas titulada
“Localización de fallas”, usted estima todavía que necesita servicio:
TACP garantiza el tubo-pantalla de este televisor contra defectos en los
materiales o en la elaboración, por un período de dos (2) años contados a
partir de la fecha de compra original al por menor.
(1) Para encontrar el Centro más cercano de Servicio Autorizado por TACP,
póngase en contacto con el Centro de Soluciones para el Consumidor de
TACP, llamando gratis al 1-800-631-3811.
(2) Usted deberá presentar su contrato de venta original o cualquier otra
prueba de compra, al Centro de Servicio autorizado por TACP.
DURANTE ESTE PERÍODO DE TIEMPO, TACP TENDRÁ LA OPCIÓN DE
REPARAR O REEMPLAZAR UN TUBO-PANTALLA QUE HUBIERE
RESULTADO DEFECTUOSO POR UN TUBO-PANTALLA NUEVO O
RECONSTRUÍDO, SIN CARGO ALGUNO PARA USTED, EXCEPTO QUE SI
REPARA O REEMPLAZA UN TUBO-PANTALLA DESPUÉS DE UN (1)
AÑO PASADA LA FECHA DE COMPRA ORIGINAL AL POR MENOR,
TODOS LOS GASTOS POR CONCEPTO DE MANO DE OBRA
RELACIONADOS CON ESA REPARACIÓN O REEMPLAZO LE
CORRESPONDERÁN A USTED.
Para más información, visite el sitio Web de TACP:
Cuando sea necesario prestar servicio de garantía durante este período de
tiempo, empleados de un Centro de Servicio autorizado por TACP vendrán a
su casa, y, según el tipo de reparación necesaria, ellos prestarán ese servicio
en su casa o se llevarán el televisor al Centro de Servicio para repararlo,
devolviéndoselo después sin cargo alguno para usted.
TODAS LAS GARANTÍAS IMPLÍCITAS EN LAS LEYES DE CUALQUIER
ESTADO DE LOS ESTADOS UNIDOS, INCLUSO LAS GARANTÍAS
IMPLÍCITAS DE COMERCIALIZACIÓN E IDONEIDAD PARA UN FIN EN
PARTICULAR, SE LIMITAN EXPRESAMENTE A LA DURACIÓN DE LAS
GARANTÍAS LIMITADAS INDICADAS ANTERIORMENTE. CON
EXCEPCIÓN DE CUALESQUIERA GARANTÍAS IMPLÍCITAS EN LAS LEYES
DE CUALQUIER ESTADO DE LOS EE.UU., CONFORME SE LIMITAN POR EL
PRESENTE, LA GARANTÍA ANTERIORMENTE MENCIONADA ES
EXCLUSIVA Y EN LUGAR DE TODA OTRA GARANTÍA, ACUERDOS Y
OBLIGACIONES SIMILARES DE TACP CON RESPECTO A LA REPARACIÓN
O EL REEMPLAZO DE CUALQUIER PIEZA. EN NINGÚN MOMENTO TACP
SE RESPONSABILIZARÁ POR DAÑOS INCIDENTALES O INDIRECTOS
(INCLUYENDO PERO SIN LIMITARSE AL LUCRO CESANTE,
Televisores de alquiler
La garantía para los televisores de alquiler comienza a partir de la fecha del
primer alquiler, o treinta (30) días después de la fecha en que ese televisor es
enviado a la empresa que los alquila, lo que suceda primero.
Garantía limitada para televisores comerciales
TACP garantiza los televisores que se venden y utilizan para propósitos
comerciales, de la manera siguiente: Todas las piezas están garantizadas
contra defectos en los materiales o en la elaboración por un período de
noventa (90) días, contados a partir de la fecha de compra original al por
menor. DURANTE ESTE PERÍODO DE TIEMPO, TACP TENDRÁ LA OPCIÓN
DE REPARAR O REEMPLAZAR CUALQUIER PIEZA QUE RESULTE
DEFECTUOSA POR UNA PIEZA NUEVA O RECONSTRUIDA, SIN CARGO
ALGUNO PARA USTED.
INTERRUPCIÓN POR EL CESE DE NEGOCIOS, MODIFICACIONES O
ELIMINACIONES DE DATOS GRABADOS CAUSADOS POR EL USO, EL
MAL USO O INEPTITUD EN EL MANEJO DE ESTE TELEVISOR).
Ninguna persona, agente, distribuidor, comerciante o compañía está autorizada a
cambiar, modificar o prorrogar los términos de esta garantía en forma alguna. El
período de tiempo dentro del cual se pueda entablar una demanda para hacer
cumplir alguna obligación de TACP que surja bajo esta garantía o bajo las leyes de
los Estados Unidos o de cualquiera de sus estados, se limita por este medio a
noventa (90) días contados a partir de la fecha en que usted tenga conocimiento
del defecto, o en la que se debería haber tenido conocimiento del mismo. Esta
limitación no se extiende a las garantías implícitas que surjan conforme a las leyes
de cualquier estado de los Estados Unidos.
Manual del propietario y tarjeta de registro del producto
Llene y devuelva por correo la tarjeta de registro del producto adjunta al
presente, o registre su televisor lo más pronto posible en línea en
www.tacp.toshiba.com/service. Al registrar su televisor, TACP podrá
ofrecerle nuevos productos específicamente diseñados para satisfacer sus
necesidades, y permitirá que podamos contactarlo en el caso improbable que
fuere necesario enviarle alguna notificación de seguridad conforme al Acta de
Seguridad de Productos del Consumidor de Estados Unidos. Sus derechos de
garantía no disminuyen si usted no llena ni devuelve dicha tarjeta de registro
del producto.
ESTA GARANTÍA LE PROPORCIONA DERECHOS LEGALES ESPECÍFICOS, Y
PUDIERA SER QUE USTED TENGA OTROS DERECHOS LOS CUALES
PUEDEN VARIAR DE UN ESTADO A OTRO EN LOS EE.UU. ALGUNOS
ESTADOS DE LOS EE.UU. NO PERMITEN LIMITACIONES EN CUANTO A LA
DURACIÓN DE UNA GARANTÍA IMPLÍCITA, NI DE CUÁNDO PUEDE
ENTABLARSE UNA DEMANDA, NI DE LA EXCLUSIÓN O LIMITACIÓN POR
DAÑOS INCIDENTALES O INDIRECTOS. POR LO TANTO, PUDIERA SER QUE
LAS LIMITACIONES O EXCLUSIONES QUE PRECEDEN NO LE
CORRESPONDAN A USTED BAJO ESAS CIRCUNSTANCIAS. [Wty-A(S) 0305]
43
J3W60321A(S)_P38-Back
43
27/2/06, 10:01 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
National Service Division
CableClear, ColorStream, FST Pure, TheaterWide et StableSound es una marca
registrada de Toshiba America Consumer Products, L.L.C.
GameTimer es una marca comercial de Toshiba America Consumer Products, L.L.C.
IMPRESO EN TAILANDIA
J3W60321A(S)_P38-Back
44
27/2/06, 10:01 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
|