SonicWALL Backup and Recovery Solutions
BACKUP & RECOVERY
CDP 6080 / CDP 6080B
Getting Started Guide
DYNAMIC SECURITY FOR THE GLOBAL NETWORK™
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Pre-Configuration Tasks
In this Section:
This section describes the SonicWALL CDP appliance and related components. Review this section before setting up your SonicWALL
CDP 6080 appliance.
•
•
•
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking CDP 6080 Package Contents
Any Items Missing?
Before setting up your SonicWALL CDP appliance, verify that your
package contains the following parts:
If any items are missing from your package,
please contact SonicWALL support.
A listing of the most current support documents are available online
1
4
5
6
SonicWALL CDP 6080
Appliance
(2) Standard Power Cords*
Front Bezel Keys
2
3
Getting Started Guide
Rack Mounting Kit
*The power cords are intended for use only in the indicated region. .
Ethernet Cable
1
2
SonicWALL Network Security Appliances
NETWORK SECURITY
CDP 6080
Getting Started Guide
3
5
6
4
Page 2 Checking CDP 6080 Package Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview of the SonicWALL CDP Appliance
Front Panel
Power Switch
D-Pad Controls
Allows the SonicWALL CDP appliance
to be powered on or off
Provides up, left, right, and down buttons to
navigate the LCD menu:
Up/Down: Navigate lists
Left: Cancel changes / return to previous
Right: Accept changes
Reset Button
Reboots the SonicWALL CDP appliance
Front Bezel Release
Allows access to drive bays under the
front bezel for addition/replacement of
hard disks (requires use of included key)
LED Indicators
Provides the following system status indications:
ALARM: Thermal or other alert condition*
ETH0/ETH1: Ethernet link (solid), activity (blinking)
HDD: Hard disk activity (blinking)
LCD Display
PWR: The appliance is powered (on/off)
Provides access to basic system
information, settings, and features using
the D-Pad controls
*For a full list of alerts, refer to the SonicWALL LED Alerts technote document
•
•
Pressing the reset button for several seconds will result in a reboot of the SonicWALL CDP appliance.
Do not plug devices into any ports (other than those indicated) unless explicitly instructed to do so by a SonicWALL technical
support representative; doing so may void your warranty.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
Dual Power Supplies
Provides redundant power
connection using the supplied
power cables
Serial Port
Provides access to a command line interface
(CLI) with DB-9 CLI cable (not included)
Ethernet Port 1
Not authorized for use
VGA Port
Not authorized for use unless explicitly
instructed by a SonicWALL technical support
representative
Ethernet Port 0 (Management/LAN)
Provides configurable Gigabit-capable
Ethernet connection to your local network
Page 4 Overview of the SonicWALL CDP Appliance
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Bezel Control Features
The SonicWALL CDP appliance is equipped with a front panel
bezel interface that allows an administrator to customize certain
aspects of the appliance or simply monitor its status without
having to log into it through a separate terminal.
Status
Main Menu
The Status menu allows you to view specific aspects of the
appliance. Once selected, the LCD displays the Status List. This
list is navigated using the Up and Down buttons. Status options
include:
Upon booting, the LCD display initially shows the Main Menu.
The menu is made up of two options:
Contains basic status values including
system resources, connections, and
port configuration values.
•
•
•
•
•
•
•
•
Appliance name
Software version
Date
Time
Uptime
Management URL
Interface eth0 IP (default LAN)
Interface eth0 subnet
Allows configuration of basic LAN port
settings. Requires system PIN for
access, default: 76642.
Use the Up and Down buttons to select the menu you wish to
enter. Click the Right button to enter it.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure
After entering a new value for a setting in the configuration
menu, you are asked if you want to commit changes. Using the
4-way D-pad, press the Right button for yes or the Left button
for no.
The Configure Menu allows you to configure specific aspects of
the appliance. Once selected, the LCD displays a PIN request.
Note: The Default PIN is 76642. This number spells SONIC
on a phone keypad. The PIN number can be changed
from the System > Administration page.
If you choose yes, the screen notifies you that the settings are
updated.
All numbers are inputted using the 4 buttons. Select the
individual digit field using the Left and Right button and select
the desired number using the Up and Down button. Digits
increase incrementally from 0 to 9. Press the Right button to
confirm your PIN and enter the Configuration Menu.
The appliance allows the user to navigate in and out of the
Configuration Menu without having to re-enter the PIN.
However, once the appliance enters Screen-Saver Mode,
whether from the 6-second time out or from pressing the Left
button from the Main Menu, the PIN number must be re-entered
again to access the Configuration Menu.
Page 6 Front Bezel Control Features
Download from Www.Somanuals.com. All Manuals Search And Download.
What You Need to Begin
Registering Your SonicWALL CDP
Appliance on MySonicWALL
A computer that meets or exceeds the following requirements:
•
•
•
•
•
•
Pentium III 450 MHZ processor
256 MB of RAM
40 MB of free disk space
A broadband Internet connection (DSL, cable, T1, or other)
A 10/100 Base-T Ethernet hub / router
Microsoft Windows 7, Vista, XP, Server 2008, Server 2003*
The SonicWALL CDP appliance must be registered on
MySonicWALL before first use. Perform the following steps to
register your SonicWALL CDP appliance:
The MySonicWALL login page is displayed.
*For the latest list of supported Windows operating systems and
service packs, refer to the SonicWALL CDP Release Notes and
the following webpage:
Page 8 What You Need to Begin
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Enter your MySonicWALL account credentials in the
Username and Password fields and then click the Submit
button.
Product Group
Select a product group from the
drop-down menu. This product
group is a logical collection of
SonicWALL products that are
managed by a user group, defined
on MySonicWALL.
Note: You need a MySonicWALL account to register the
SonicWALL CDP 6080. You can create one by clicking
the Register Now link.
Authentication Code
Enter your authentication code,
found on the bottom of your
SonicWALL CDP appliance (just
below the serial number).
3. On the MySonicWALL page, click My Products in the
navigation bar. Then, select Register Product.
4. Complete the fields as described in the table below:
Field
Description
Serial Number
Enter the serial number, found on
the bottom of your SonicWALL
CDP appliance.
Friendly Name
Enter a descriptive name for your
SonicWALL CDP appliance.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Click the Submit button.
The message “Please select an offsite backup location”
displays:
Alert: If you change the offsite data backup location, the data
that was saved in the previous location is lost.
7. Click the Submit button.
The Service Management page is displayed.
6. In the Location drop-down menu, select an offsite data
backup location, either NORTH AMERICA - WEST or
Europe.
Note: You will need the Registration Code during initial
configuration of your SonicWALL CDP.
Page 10 Registering Your SonicWALL CDP Appliance on MySonicWALL
Download from Www.Somanuals.com. All Manuals Search And Download.
Activating Offsite Data Backup Service
The activation status displays with the expiration date and
offsite capacity.
The SonicWALL CDP Offsite Data Backup Service is an
optional offsite backup and recovery solution. Perform the
following steps to activate your Offsite Data Backup Service:
1. On the Service Management page in MySonicWALL, scroll
down to Applicable Services. If you do not have an Offsite
Data Backup Service activation key, click the Buy icon or
contact your SonicWALL vendor.
If you have a license key, click the Key icon.
3. To activate the SonicWALL Site-to-Site Backup service,
click the Buy or Key icon.
4. To enter an existing license key, use the same method as
described above for the Offsite Data Backup Service.
Note: Bare Metal Recovery and other services can also be
activated on the Service Management page. For
information about using Bare Metal Recovery, refer to
the SonicWALL Bare Metal Recovery Administrator’s
Guide, available on MySonicWALL or at:
2. Type your key into the Activation Key field, select the I
have read and agreed to all of the terms and conditions
mentioned above checkbox, and then click Submit.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Determining Network Information
Before continuing, determine the following network
configuration information and record it for your reference:
Networking Information
General Information
CDP IP Address:
Select an available static IP
address for your SonicWALL
CDP appliance that is within the
range of your local subnet.
Server Name:
Select a friendly name for your
SonicWALL CDP appliance
(maximum 32 characters).
_____________________
_____________________
Password:
Select a password for your
SonicWALL CDP appliance
(default is password).
CDP Subnet Mask:
Enter the subnet mask for the
local subnet where you are
installing your SonicWALL CDP
appliance.
_____________________
_____________________
Serial Number:
Record the serial number found
on the bottom of your SonicWALL
CDP appliance.
_____________________
Gateway IP Address:
Record the IP address of your
network’s gateway device (such
as your perimeter firewall/router).
Authentication Code:
Record the authentication code
found on the bottom of your
SonicWALL CDP appliance.
_____________________
_____________________
Registration Code:
DNS Server 1:
Record your DNS Server
information.
Record the registration code that
is generated in mysonicwall.com.
_____________________
DNS Server 2 (optional):
_____________________
_____________________
Page 12 Determining Network Information
Download from Www.Somanuals.com. All Manuals Search And Download.
6. If the appliance does not power up immediately, press the
power switch on the front to turn it on.
7. Open a Web browser on the computer and point it to:
http://192.168.168.169 (the default IP address of the
SonicWALL CDP appliance). The SonicWALL CDP login
screen displays.
Powering On and Connecting to the
Appliance
After registering your SonicWALL CDP appliance on
MySonicWALL, you are ready to turn on the appliance and
connect a computer to it for initial configuration.
1. Place the SonicWALL CDP appliance and your
management computer next to each other for the
initialization process.
2. Set the LAN IP address of your management computer to a
static IP address on the 192.168.168.0/24 subnet, such as
192.168.168.50. For help with setting a static IP address on
your computer, refer to Configuring a Static IP Address on
Note: One or more security warnings may display while
connecting to the SonicWALL CDP Web management
interface. Continue to the website, and accept the
certificate if required, to login to the SonicWALL CDP
appliance.
8. Enter “admin” in the Name field and “password” in the
Password field, select your language from the Language
drop-down menu, and click the Login button.
3. Using an Ethernet cable, connect the LAN port of computer
to the LAN port on the back of your SonicWALL CDP
appliance.
Management
Station
Ethernet Port
(in the rear)
4. Securely attach each provided power adaptor to a provided
power cord.
5. Connect the power adaptors to the back of the appliance,
and insert the plug ends into grounded 110/120V outlets.
For redundancy, plug the power adaptors into outlets on
different circuits.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring a Static IP Address on Windows
Complete the following steps to configure your management
computer with a static IP address:
Windows XP
Windows 7
1. On the Windows Start menu, highlight Connect To and
then select Show All Connections to open the Network
Connections window.
1. Open a My Computer window.
2. Type Network Connections into the location bar at the top
of the window and press Enter.
If Connect To is not available, directly select Network
Connections, or select Control Panel and then double-
click Network Connections in the Control Panel window.
The window changes to the Control Panel > All Control
Panel Items > Network Connections folder.
3. In the Network Connections window, double-click Local
Area Connection.
4. If the Local Area Connection Status window opens, click
2. In the Network Connections window, double-click Local
Area Connection.
3. In the Local Area Connection Status window, click the
the Properties button.
Properties button.
5. In the Local Area Connection Properties window, select
Internet Protocol Version 4 (TCP/IPv4), and then click
the Properties button.
6. Select Use the following IP address and type an IP
address on the 192.168.168.0/24 subnet, such as
192.168.168.50, in the IP address field.
7. Type 255.255.255.0 in the Subnet Mask field.
8. Click OK in the Properties window.
9. Click Close in the Local Area Connection Properties
4. In the Local Area Connection Properties window, select
Internet Protocol (TCP/IP), and then click the Properties
button.
5. Select Use the following IP address and type an IP
address on the 192.168.168.0/24 subnet, such as
192.168.168.50, in the IP address field.
6. Type 255.255.255.0 in the Subnet Mask field.
7. Click OK in the Properties window.
8. Click Close or OK in the Local Area Connection Properties
window for the settings to take effect.
window for the settings to take effect.
Page 14 Powering On and Connecting to the Appliance
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring Local Time Zone Settings
Configuring Appliance Settings
1. On the System > Settings page, click the Time tab.
2. Complete the fields as described in the table below, then
After registering your SonicWALL CDP on MySonicWALL and
connecting a management computer to it, you are ready to
configure the appliance for use on your network.
click Apply.
Changing the Administrator Password
Field
Description
1. On the System > Settings page, click the Password tab.
Time (hh:mm:ss)
Select the time in 24-hour format by
clicking the up or down arrows next to
each field (hours, minutes, seconds).
2. Type the desired password into the Password field, and
again into the Verify Password field, then click Apply.
You are logged out of the SonicWALL CDP appliance.
Date
Select the date (month, day, year)
from the pop-up calendar.
3. In the Logged Out screen, click the Login Again button
and then log in as “admin” using your new password.
Time Zone
Select your local time zone from the
drop-down list.
Set Time
Automatically
using NTP
Select this checkbox to allow the time
to be set automatically using NTP.
Configure NTP servers on the NTP
tab.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the Appliance Host Name and Domain
1. In the Web management interface, click Network in the
navigation pane, and then click Settings.
2. On the Name Server tab, click the Configure icon for the
To allow access to your SonicWALL CDP appliance by fully
qualified domain name (FQDN), you must configure a unique
host name and set the domain.
DNS IP address.
3. In the Server field, type in the IP address of the DNS
server used in your local network. You can look at the DNS
settings on your gateway appliance to determine this.
1. In the Web management interface, click Network in the
navigation pane, and then click Settings.
2. On the Summary tab, type the host name for the CDP
appliance into the Host Name field.
3. Type the domain used by the appliance into the Host
Domain field.
4. Type a descriptive name for the appliance into the Friendly
Name field. This name is displayed in the Available
Appliances list when initializing the SonicWALL CDP Agent
on a client machine.
4. Click OK.
Configuring a Static IP Address for the Appliance
5. Click the Apply button.
This procedure describes how to configure your SonicWALL
CDP appliance with a static IP address. After changing the IP
address of your appliance, you must point your browser to the
new IP address to access the Web management interface.
Configuring the Domain Name Server Address
You must configure the correct DNS address settings in order to
register and use your SonicWALL CDP appliance. The DNS
server must be able to resolve external Internet names.
For your records, enter the chosen IP address for your
SonicWALL CDP appliance in the space provided below.
For your records, enter the DNS server IP address below.
CDP IP address:
See Determining
DNS Server IP address:
See Determining
______.______.______.______
______.______.______.______
Page 16 Configuring Appliance Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
1. In the Web management interface, click Network in the
5. In the Default Gateway field, enter the IP address of the
navigation pane, and then click Settings.
default gateway (usually a firewall) for your local network.
2. On the Interface tab, click the Configure icon for the eth0
6. Click OK. A Processing indicator is displayed, but your
session is already disconnected and you do not need to
wait.
interface.
Note: After applying the IP address change, your current
Web management interface session is disconnected.
You must point your browser to the new IP address to
access the Web management interface again.
3. In the IP Address field, enter an unused static IP address
that is within the range of your local subnet.
7. Disconnect the Ethernet cable from your computer and
from the SonicWALL CDP appliance.
8. Reset your computer to use the Obtain an IP address
automatically option, if using a DHCP server, or reset it to
the original static IP address for your LAN. See Configuring
For example, if the LAN IP address of your gateway firewall
is 10.215.10.1 and the subnet mask is 255.255.255.0, you
could set the static IP address on your SonicWALL CDP
appliance to 10.215.10.61.
9. If using a wired connection, reconnect your computer to an
available port on a network device on your local network.
Continue to the next section to connect the SonicWALL CDP
appliance to your local area network.
4. In the Subnet field, enter your subnet mask.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the SonicWALL CDP Appliance to Your Network
Your SonicWALL CDP appliance is designed to operate in most network deployments with minimal configuration.
SonicWALL Network Security Appliance
LAN
Network Security Appliance
NSA
SonicWALL CDP
Local Clients
Local Servers
DMZ
Web Servers
Internet
Email Servers
SonicWALL CDP Appliance
WAN
Remote VPN Users
Remote Backup Server
LAN
DMZ
WAN
Perform the following steps to physically connect your SonicWALL CDP appliance to your network:
1. Plug one end of the provided Ethernet cable into the LAN port on the back of your SonicWALL CDP appliance.
2. Plug the other end of the cable into an open port on your network hub or switch.
Page 18 Connecting the SonicWALL CDP Appliance to Your Network
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Complete the fields as described in the table below:
Configuring Mail Settings
Mail settings are required for the administrator to receive email
alerts. The Alerts tab already contains default alert settings.
Field
Description
Server
Type in the name or IP address of the mail
server; for example, mail.company.com.
Note: You must complete the network configuration of the
appliance and physically connect it to your local area
network to allow mail settings to work properly.
Recipient
Email
Type in the email address of the administrator
for the SonicWALL CDP appliance.
Address
1. Log in to a management computer that is connected to a
network device on your local network.
2. Point your browser to the static IP address of the
SonicWALL CDP appliance. The CDP login screen
displays.
From Email
Address
Type in the email address to use as the sender
when alert emails are sent to the administrator;
for example, [email protected].
From Email
Domain
Type in the domain used by the sender; for
example, localdomain or a regional domain.
3. Log in as admin, using the configured administrator
password.
Username
Type in a user name for the From Email
Address, if required by your mail server.
4. On the System > Settings page, click the Mail tab.
Password
Type in a password for the From Email
Address, if required by your mail server.
Verify
Re-enter the password.
Password
6. Click Apply.
7. Click Send Test Email to send a test email to the
configured Recipient Email Address.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Type the product registration code from MySonicWALL into
Activating Your SonicWALL CDP Appliance
the Registration Code field.
Perform the following steps to activate your SonicWALL CDP
appliance. You will need the product registration code that you
obtained in Registering Your SonicWALL CDP Appliance on
MySonicWALL - page 8 to complete this section.
Alert: If the appliance does not have Internet connectivity,
you will need to use the Manual Keyset to activate
SonicWALL CDP. The Manual Keyset is available on
MySonicWALL.
4. Click the Register button.
For information about upgrading the firmware after activating
your appliance, see the Upgrading Appliance Firmware section
in the SonicWALL CDP Administrator’s Guide, and check the
release notes for special instructions.
The Processing indicator appears for a few seconds, and
then the Registration Code field appears as Registered
when finished.
1. On your management computer, point your browser to the
SonicWALL CDP appliance IP address and log in to the
Web management interface.
Type “admin” for the username, and type in the current
password for the admin account.
2. Click the Register button in the top right corner of the Web
management interface.
You have successfully completed registration and activated
your SonicWALL CDP appliance. Your SonicWALL CDP 6080
is now fully operational. Continue with Installing and Verifying
The System > Registration/Licenses page is displayed.
Page 20 Activating Your SonicWALL CDP Appliance
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installing and Verifying SonicWALL CDP Agent
In this Section:
This section provides instructions for installing the SonicWALL CDP Agent software and testing backup functionality with your
SonicWALL CDP appliance.
•
•
•
•
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
SonicWALL CDP User Interfaces
Downloading and Installing SonicWALL
CDP Agent Software
SonicWALL provides the following user interfaces for managing
the features and functionality of the SonicWALL CDP:
Perform the following procedures to install the SonicWALL CDP
Agent and Local Archive Manager software on each agent
computer that requires access to the SonicWALL CDP
appliance for data backup.
SonicWALL CDP Web Management Interface—Accessed
through a browser, this Web-based interface runs on the
appliance and is used by the SonicWALL CDP administrator to
configure local and global policies, obtain logs and reports, set
email notifications and other administrative settings, configure
network settings, access system diagnostics, and manage
agent machines.
Downloading the Latest SonicWALL CDP Agent Software
1. Open a Web browser on the agent computer.
Address bar. The MySonicWALL login page displays.
3. Log in to MySonicWALL, and click Download Center in
SonicWALL CDP Agent User Interface—This application runs
on individual user workstations, allowing users to connect to the
SonicWALL CDP appliance, create backup tasks and
schedules, and restore file sets and application data.
Administrators can use the Agent User Interface to access, edit,
and restore backup data on SonicWALL CDP appliances for all
agent machines.
the left navigation pane.
4. Select the CDP Firmware/Software option matching your
appliance model from the Software Type drop-down
menu.
SonicWALL CDP Local Archive Manager—This application
allows you to copy data from a SonicWALL CDP appliance onto
a USB drive, and to restore the data from the USB drive to an
individual computer or server. The data can be encrypted on the
USB drive, and you can configure local archiving tasks that
periodically copy data from the appliance to a USB drive.
Page 22 SonicWALL CDP User Interfaces
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Locate the CDP Agent Software link for your agent
machine (Windows/Mac/Linux) under Description in the
Available Software section of the page.
4. In the End-User License Agreement screen, select the I
accept the terms in the license agreement checkbox,
and click Next to continue.
6. Depending on your browser, either click or right-click on the
desired Agent software link, and follow the prompts to save
the installer to a location on your computer.
Installing the SonicWALL CDP Agent Software
1. Navigate to the folder where you downloaded the installer.
2. Double-click the CDPSetup.exe file to begin the installation
process.
If you are running Windows or using a third-party firewall,
you may receive a warning during installation of the
SonicWALL CDP Agent software. For more information on
configuring your firewall to work with the SonicWALL CDP
appliance, refer to the SonicWALL CDP Agent User’s
Guide.
3. Click Next in the Welcome screen.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
5. In the Choose Setup Type screen, select either Typical,
Typical installation installs the most common program
features, including the Agent User Interface and Agent
Service. A Typical installation uses less disk space than a
Complete installation. The Local Archive Manager is not
installed with a Typical installation.
Custom or Complete, and then click Next.
Complete installation will install all the program features.
To include the Local Archive Manager in the installation,
select Complete.
Custom installation allows you to select which program
features you want installed. This installation option is
recommended for advanced users.
Page 24 Downloading and Installing SonicWALL CDP Agent Software
Download from Www.Somanuals.com. All Manuals Search And Download.
6. The installer displays a screen asking if you want to install
the Adobe AIR application, which is required for proper
operation of the Agent User Interface. Click Install to
continue the Agent software installation.
8. Once the software installation is complete, click Finish.
7. In the Ready to Install SonicWALL CDP screen, click
Install to begin the actual installation.
The installer places shortcuts on the computer desktop for
the SonicWALL CDP Agent UI and SonicWALL CDP Local
Archive Manager (if installed).
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
6. In the left pane, under Computer, select a folder that has
Verifying SonicWALL CDP Operation
some files you can back up for this test.
To verify that your SonicWALL CDP appliance can successfully
back up data from an agent computer, perform the following
steps:
1. Launch the SonicWALL CDP Agent User Interface by
double-clicking the desktop shortcut or from the Windows
Start menu:
Programs > SonicWALL > SonicWALL Continuous
Data Protection > SonicWALL CDP Agent UI.
If you are running Windows or using a third-party firewall,
you may receive a warning asking to accept the certificate
when you launch the SonicWALL CDP software. Accept
the certificate to continue.
2. In the CDP Agent User Interface, click the Change
Appliance icon at the bottom of the left pane to show
available appliances.
7. Under Add New Rule, select All Files or a specific file
type from the File Name and Patterns drop-down list for
backup.
3. Select the recently registered SonicWALL CDP appliance
and click the Connect to Appliance icon.
4. Click the Policies tab.
9. Click OK.
5. Double-click Files and Folders: Default CDP Files and
Folders, to edit it.
Backups begin immediately when using CDP Method.
The Files and Folders window opens.
Page 26 Verifying SonicWALL CDP Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Click the My Backups tab to view specific folders and
check backup status.
Note: For more information on configuring your SonicWALL
CDP appliance, refer to the SonicWALL CDP
Administrator’s Guide and the SonicWALL CDP Agent
User’s Guide at:
Congratulations! You have successfully set up and tested your
SonicWALL CDP appliance operation.
To enable additional computers to back up data to the
SonicWALL CDP 6080 appliance, simply install the SonicWALL
CDP Agent software on each computer.
11. Click the Status tab to see data being backed up and view
the quota used.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
4. If you are running Microsoft Windows XP SP2 or Windows
Server 2003, verify that Data Execution Prevention (DEP)
is configured to allow SonicWALL CDP:
Troubleshooting SonicWALL CDP Agent
Operation
•
Under Windows Services, stop the
CDPAgentService.exe service.
Right-click My Computer and select Properties, then
select the Advanced tab.
Under Performance, click Settings.
Select the Data Execution Prevention tab.
If DEP is enabled for all programs and services, then
add CDPAgentService.exe, CDPAutoUpdate.exe, and
Lasso.Client.exe to the list.
If your SonicWALL CDP Agent application does not start, verify
the following:
•
1. The software must be installed by a user with
administrative rights.
2. The operating system must be upgraded to the latest
released service pack.
3. If you have a personal firewall, add exceptions for the
following:
•
•
•
•
•
•
CDPAgentservice.exe
Lasso.Client.exe
CDPAutoUpdate.exe
•
•
Click Apply.
Start the Agent Service again.
5. Verify that there is no other content filtering or personal
firewall software running.
Page 28 Troubleshooting SonicWALL CDP Agent Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support
SonicWALL Live Product Demos
SonicWALL offers Web-based and telephone support to
customers who have a valid warranty or who have purchased a
Support Contract. SonicWALL also offers a full range of
consulting services to meet your needs, from our innovative
implementation services to traditional statement of work-based
services.
The SonicWALL Live Demo site provides free test drives of
SonicWALL security products and services through interactive
live product installations:
•
•
•
•
•
•
•
SonicOS Deep Packet Inspection Platform
Continuous Data Protection
SSL VPN Secure Remote Access
Content Filtering
Secure Wireless Solutions
Email Security
For further information, visit:
SonicWALL GMS and ViewPoint
For further information, visit:
Page 30 Customer Support
Download from Www.Somanuals.com. All Manuals Search And Download.
Knowledge Portal
The Knowledge Portal allows users to search for SonicWALL documents based on the following types of search tools:
•
•
•
Browse
Search for keywords
Full-text search
For further information, navigate to the Support > Knowledge Portal page at:
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
SonicWALL User Forums
The SonicWALL User Forums allow users to communicate and
discuss a variety of security and appliance subject matters. The
forums include a variety of topics among the following
categories:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Firewall topics
SSL VPN topics
Mobile Connect topics
Continuous Data Protection topics
Email Security topics
Scrutinizer topics
WAN Acceleration topics
Content Security Manager topics
GMS, Analyzer, and ViewPoint topics
Network Anti-Virus topics
Security Services and Content Filtering topics
SonicPoint and Wireless topics
VPN Client topics
VPN site-to-site and interoperability topics
Beta Forums
For further information, log in to the SonicWALL Forums
website using your MySonicWALL account credentials:
Page 32 SonicWALL User Forums
Download from Www.Somanuals.com. All Manuals Search And Download.
Training
SonicWALL offers an extensive sales and technical training
curriculum for Network Administrators, Security Experts and
SonicWALL Medallion Partners who want to enhance their
knowledge and maximize their investment in SonicWALL
Products and Security Applications. SonicWALL Training
provides the following resources for its customers:
•
•
•
•
•
E-Training
Instructor-Led Training
Custom Training
Technical Certification
Authorized Training Partners
For further information, visit:
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Documentation
See the following documents for more information:
•
•
•
SonicWALL CDP Administrator’s Guide
SonicWALL CDP Agent User’s Guide
SonicWALL CDP MS Exchange InfoStore Backup and
Restore Guide
•
•
SonicWALL CDP MS Exchange User Mailbox Backup and
Restore Guide
SonicWALL CDP Local Archiving Guide
For further information, visit:
Page 34 Related Documentation
Download from Www.Somanuals.com. All Manuals Search And Download.
SonicWALL Secure Wireless Network Integrated Solutions Guide
The official guide to SonicWALL’s market-leading wireless networking and security devices. This 512-page book is available in hardcopy.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 36
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Information
Regulatory Model/Type
2RK02-067
Product Name
SonicWALL CDP 6080
SonicWALL CDP 6080B
Unauthorized Ports
Do not plug devices into any ports (other than those indicated) unless explicitly instructed to do so by a SonicWALL technical support
representative. Doing so may void your warranty.
Page 38 Safety and Regulatory Information
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Allow unrestricted airflow around the unit and through the
vents on the side of the unit. A minimum of 1 inch
(25.44mm) clearance is recommended.
Mounting the SonicWALL CDP 6080
The SonicWALL CDP appliance is designed to be mounted in a
standard 19-inch rack mount cabinet. The following conditions
are required for proper installation:
If installed in a closed or multi-unit rack assembly, the
operating ambient temperature of the rack environment
may be greater than room ambient. Therefore,
consideration should be given to installing the equipment in
an environment compatible with the maximum
recommended ambient temperature shown above.
Mount the SonicWALL appliances evenly in the rack in
order to prevent a hazardous condition caused by uneven
mechanical loading.
Consideration must be given to the connection of the
equipment to the supply circuit. The effect of overloading
the circuits has minimal impact on overcurrent protection
and supply wiring. Appropriate consideration of equipment
nameplate ratings must be used when addressing this
concern.
DC configuration includes input cable with protective
earthing conductor (green and yellow wire). This conductor
must be connected to safety earth ground of circuit.
Never remove or install a power supply while the power
cord is attached to the power supply that is being removed
or installed.
A suitably rated and approved branch circuit breaker shall
be provided as part of the building installation. Follow local
code when purchasing materials or components.
•
Use the mounting hardware recommended by the rack
manufacturer and ensure that the rack is adequate for the
application.
•
Four mounting screws, compatible with the rack design,
must be used and hand tightened to ensure secure
installation. Choose a mounting location where all four
mounting holes line up with those of the mounting bars of
the 19-inch, rack mount cabinet.
•
•
•
•
•
Mount in a location away from direct sunlight and sources
of heat. An ambient temperature of 104º F (40º C) is the
maximum allowed.
Route cables away from power lines, fluorescent lighting
fixtures, and sources of noise such as radios, transmitters,
and broadband amplifiers.
As shipped from the factory this SonicWALL product
includes two power supplies for redundant AC power and
added reliability. A field conversion is available to convert to
DC mains.
•
•
•
•
•
The included power cord is intended for use in North
America AC mains installation only. For European Union
(EU) customers, and DC mains, a power cord is not
included.
Ensure that no water or excessive moisture can enter the
unit.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
•
This model is shipped as AC mains configuration uses
standard 3 conductor appliance couplers. A field
conversion is available to change to DC mains. The DC
mains is connected to terminal post. Do not connect AC
configured product to DC mains and do not connect DC
configured product to AC. Detailed instructions are
provided with the DC conversion kit. Product must be
configured as all DC or all AC.
Mounting Instructions in German
Das SonicWALL Modell ist für eine Montage in einem
standardmäßigen 19-Zoll-Rack konzipiert. Für eine
ordnungsgemäße Montage sollten die folgenden Hinweise
beachtet werden:
•
Vergewissern Sie sich, dass das Rack für dieses Gerät
geeignet ist und verwenden Sie das vom Rack-Hersteller
empfohlene Montagezubehör.
•
•
DC rating includes tolerances. Do not operate product
outside of range shown on product label.
•
Verwenden Sie für eine sichere Montage vier passende
Befestigungsschrauben, und ziehen Sie diese mit der
Hand an. Wählen Sie einen Ort im 19-Zoll-Rack, wo alle
vier Befestigungen der Montageschien verwendet werden.
Wählen Sie für die Montage einen Ort, der keinem direkten
Sonnenlicht ausgesetzt ist und sich nicht in der Nähe von
Wärmequellen befindet. Die Umgebungstemperatur darf
nicht mehr als 40 °C betragen.
This product is not intended to be installed and used in a
home or public area accessible to the general population.
When installed in schools this equipment must be installed
in a secure location accessible only by trained personnel.
Thumbscrews should be tightened with a tool after both
installation and subsequent access to the rear of the
product.
Reliable grounding of rack-mounted equipment must be
maintained. Particular attention must be given to power
supply connections other than direct connections to the
branch circuits, such as power strips.
To disconnect AC power, both power cords must be
removed.
To disconnect DC power, an external properly rated
disconnect device must be provided by building or rack
installation.
•
•
•
•
•
•
Achten Sie darauf, das sich die Netzwerkkabel nicht in der
unmittelbaren Nähe von Stromleitungen, Leuchtstoffröhren
und Störquellen wie Funksendern oder
Breitbandverstärkern befinden.
Das beigefügte Netzkabel ist nur für den Gebrauch in
Nordamerikas vorgesehen. Für Kunden in der
Europäischen Union und Gleichstromversorgung ist kein
Netzkabel beigefügt.
Stellen Sie sicher, dass das Gerät vor Wasser und hoher
Luftfeuchtigkeit geschützt ist.
•
•
Page 40 Mounting Instructions in German
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Stellen Sie sicher, dass die Luft um das Gerät herum
zirkulieren kann und die Lüftungsschlitze an der Seite des
Gehäuses frei sind. Hier ist ein Belüftungsabstand von
mindestens 26 mm einzuhalten.
Wenn das Gerät in einem geschlossenen 19"-Gehäuse
oder mit mehreren anderen Geräten eingesetzt ist, wird die
Temperatur in der Gehäuse höher sein als die
Umgebungstemperatur. Achten Sie daraf, daß die
Umgebungstemperatur nicht mehr als 40° C beträgt.
Bringen Sie die SonicWALL waagerecht im Rack an, um
mögliche Gefahren durch ungleiche mechanische
Belastung zu vermeiden.
•
Die Wechselstrom Konfiguration verwendet standardisierte
Kaltgerätekabel. Sie können einem Umbaukit für
Gleichstrom bestellen. Die DC-Hauptleitungen wird an
Terminalpfosten angeschlossen. Schließen Sie kein
Wechselstrom konfiguriertes Produkt an Gleichstrom an.
Und schließen Sie kein Gleichstrom konfiguriertes Produkt
an Wechselstrom an. Das Umbaukit beinhaltet eine
detaillierte Beschreibung. Das Gerät muss komplett mit
Gleichstrom oder Wechselstrom konfiguriert sein.
Gleichstrom akzeptiert Toleranzen. Betreiben Sie das
Gerät nicht außerhalb des Bereiches, der auf dem
Aufkleber des Gerätes angegeben ist.
Die Gleichstrom Konfiguration beinhaltet einen
Anschlusskabel mit Erdung (Grün-Gelbes Kabel). Diese
Kabel muss an den Erdungsschaltkreis angeschlossen
werden.
Dieses Produkt ist nicht dafür entwickelt, um in Bereichen
mit öffentlichem Zugriff betrieben zu werden. Wenn es in
Schulen betrieben wird stellen Sie sicher, dass sich das
Gerät in einem abgeschlossenen Raum installier wird, der
nur von speziell ausgebildetem Personal betrieben werden
kann.
•
•
•
•
Prüfen Sie den Anschluss des Geräts an die
Stromversorgung, damit der Überstromschutz sowie die
elektrische Leitung nicht von einer eventuellen Überlastung
der Stromversorgung beeinflusst werden. Prüfen Sie dabei
sorgfältig die Angaben auf dem Aufkleber des Geräts.
Wenn Sie das Netzteil wechseln, entfernen Sie unbedingt
die Stromversorgung von dem zu wechselnden Netzteil.
Ein angemessen dimensionierter und geprüfte Sicherung,
sollte Bestandteil der Haus-Installation sein. Bitte folgen die
den lokalen Richtlinien beim Einkauf von Material oder
Komponenten.
•
•
•
•
•
Vergewissern Sie sich, dass die Schrauben nach dem
Austausch mit entsprechendem Werkzeug fest
anngezogen werden.
Eine sichere Erdung der Geräte im Rack muss
gewährleistet sein. Insbesondere muss auf nicht direkte
Anschlüsse an Stromquellen geachtet werden wie z. B. bei
Verwendung von Mehrfachsteckdosen.
•
Dieses Produkt wird mit zwei Wechselstrom-Netzteilen als
redundant Stromversorgung zur erhöhten Verfügbarkeit
ausgeliefert. Ein Umbaukit in Gleichstromversorgung ist
verfügbar.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 41
Download from Www.Somanuals.com. All Manuals Search And Download.
Lithium Battery Warning
Hinweis zur Lithiumbatterie
The Lithium Battery used in the SonicWALL Internet security
appliance may not be replaced by the user. The SonicWALL
must be returned to a SonicWALL authorized service center for
replacement with the same or equivalent type recommended by
the manufacturer. If, for any reason, the battery or SonicWALL
Internet security appliance must be disposed of, do so following
the battery manufacturer's instructions.
Die in der Internet Security appliance von SonicWALL
verwendete Lithiumbatterie darf nicht vom Benutzer
ausgetauscht werden. Zum Austauschen der Batterie muss die
SonicWALL in ein von SonicWALL autorisiertes Service-Center
gebracht werden. Dort wird die Batterie durch denselben oder
entsprechenden, vom Hersteller empfohlenen Batterietyp
ersetzt. Beachten Sie bei einer Entsorgung der Batterie oder
der SonicWALL Internet Security appliance die diesbezüglichen
Anweisungen des Herstellers.
Cable Connections
All Ethernet cables are designed for intra-building connection to
other equipment. Do not connect these ports directly to
communication wiring or other wiring that exits the building
where the SonicWALL is located.
Kabelverbindungen
Alle Ethernet-Kabel eignen sich für die Verbindung von Geräten
in Innenräumen. Schließen Sie an die Anschlüsse der
SonicWALL keine Kabel an, die aus dem Gebäude
herausgeführt werden, in dem sich das Gerät befindet.
Page 42 Lithium Battery Warning
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding the Expansion Pack License Key to MySonicWALL
Adding the CDP 6080 Expansion Pack
To add the Expansion Pack license key to your SonicWALL
CDP appliance on MySonicWALL, perform the following steps:
The SonicWALL CDP 6080 Expansion Pack contains four hard
drives to insert into the secondary array slots of your
SonicWALL CDP appliance. You can insert the drives into your
CDP appliance while it is powered on.
1. Open a Web browser on the computer you are using to
manage the SonicWALL CDP 6080.
To add and activate the Expansion Pack, you will need access
to MySonicWALL and to the SonicWALL CDP Web
management interface. Your CDP appliance must have Internet
access to connect to the SonicWALL licensing server to activate
the new drives.
address field.
3. On the MySonicWALL login page, enter your
MySonicWALL account username and password in the
appropriate fields and then click the Submit button.
4. In the Register A Product field, enter the license key for
the Expansion Pack, and then click Next.
The Expansion Pack license key is provided on the certificate
included in the Expansion Pack shipping box. The license key
must be entered in your MySonicWALL account before you can
access the drives.
5. If you have more than one registered SonicWALL CDP
6080 appliance, select the one on which you plan to install
the Expansion Pack. The Service Management page
displays.
The front bezel on the SonicWALL CDP appliance covers the
drive slots. The bezel can be unlocked with the front bezel
security key supplied with the appliance.
Note: The Expansion Pack license key can only be applied to
one SonicWALL CDP 6080 appliance.
See the following sections:
6. On the Service Management page, you can scroll down to
verify that the Expansion Pack row under Desktop &
Server Software does not show Enter Key in the Options
column, since you have already entered the license key.
•
•
•
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 43
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Optionally click the Expansion Pack link to view the
The Security Services table is updated to show that the
status.
Expansion Pack is licensed.
Activating the Expansion Pack License on the SonicWALL
CDP Appliance
After adding the Expansion Pack license key to the SonicWALL
CDP appliance on MySonicWALL, you must activate the
license on the appliance itself in the Web management
interface.
To activate the Expansion Pack license on the SonicWALL CDP
appliance, perform the following steps:
1. Log into the Web management interface and navigate to
the System > Registration/Licenses page.
2. Click the Refresh button to force the appliance to
communicate with the SonicWALL licensing server and
apply the Expansion Pack license.
Page 44 Adding the CDP 6080 Expansion Pack
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting the Expansion Pack Drives
2. On your SonicWALL CDP appliance, use the front bezel
key to unlock the front bezel, then remove the front bezel to
expose the hard drive arrays.
3. Press the square buttons to pop out the handles and then
remove the place holder inserts from slots D4, D5, D6, and
D7 of the top array. The inserts prevent dust and foreign
objects from getting into the drive slots.
Warning: Do not insert anything other than the SonicWALL
approved hard drives into the SonicWALL CDP
appliance.
The Web management interface provides a graphical view of
the hard drive arrays on the SonicWALL CDP 6080 appliance.
The best practice is to view the arrays on the System > RAID
page during the insertion process.
Warning: Be careful not to remove the hard drives from the
Main Array (slots D0, D1, D2, and D3) while the
appliance is powered on. Removing more than one
drive from an active array will cause loss of data.
To physically access the hard drive arrays, you must remove
the front bezel. If the front bezel is locked, use the front bezel
security key supplied with your appliance to unlock it.
4. Remove the hard drives from the Expansion Pack shipping
carton.
5. Apply the stickers for D4, D5, D6, and D7 to the drive
handles. While holding the drive with the label side up,
place the sticker near the edge of the handle next to the
square button.
6. Pop open the drive handle on the D4 hard drive by
pressing the square button and insert the drive into slot D4
(the left-most slot) of the Secondary Array, label side up
with the handle sticking out.
To view the hard drive arrays and insert the Expansion Pack
drives into the SonicWALL CDP appliance, perform the
following steps:
1. In the Web management interface, navigate to the System
> RAID page. The Secondary Array appears as black
rectangles above the Main Array, indicating that no drives
are present.
7. Press the drive firmly into place to seat the connectors and
then close the handle.
8. Pop open the handles on the D5, D6, and D7 drives and
insert them into slots D5, D6, and D7, respectively. Press
firmly to seat the connectors, and then close the handles.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 45
Download from Www.Somanuals.com. All Manuals Search And Download.
9. As the System > RAID screen refreshes (every 30
seconds), you will see the LED indicators for the drive slots
in the Secondary Array turn green as the SonicWALL CDP
appliance senses the inserted drives.
10. Click the Add Expansion Pack button. The SonicWALL
CDP appliance begins building the array. This can take up
to 30 minutes.
When all the drives are inserted, all drive slot LEDs turn
green, and the Add Expansion Pack button appears.
11. Wait until the SonicWALL CDP finishes building the array.
When finished, the status displays OK.
Note: If the Expansion Pack license has not been added to
the SonicWALL CDP on both MySonicWALL and in the
Web management interface, the Add Expansion Pack
button is not displayed. You must activate the license
before you can access the drives.
Page 46 Adding the CDP 6080 Expansion Pack
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Re-install the front bezel, being sure to properly line up the
LCD connectors.
1. On your SonicWALL CDP appliance, use the front bezel
key to unlock the front bezel, then remove the front bezel to
expose the hard drive array.
2. In the Web management interface, navigate to the
System > RAID page.
The best practice is to align and seat the right side of the
bezel (as you are facing the front of the SonicWALL CDP
appliance), then view the connectors from above as you
carefully press the left side of the bezel into place.
The defective drive is indicated by a red LED. When you
mouse over the drive, a drive status box displaying a status
such as DEVICE ERROR, UNKNOWN, or NOT-PRESENT
appears.
You might see a different status than those listed,
depending on the condition of the drive as interpreted by
the RAID controller.
13. Lock the bezel with the front bezel security key.
Replacing a Single Hard Drive
The 2 TB replacement hard drive can be inserted into any drive
slot on your SonicWALL CDP 6080 appliance. You can insert
the drive while the SonicWALL CDP appliance is powered on.
A status of DEGRADED is displayed for the array.
The front bezel on the SonicWALL CDP appliance covers the
drive slots. The bezel can be unlocked with the front bezel
security key supplied with the appliance.
The Web management interface provides a graphical view of
the hard drive array on the SonicWALL CDP appliance. The
best practice is to view the array on the System > RAID page
during the replacement process.
Removing the Defective Hard Drive from the SonicWALL
CDP Appliance
3. On the appliance, press the square button on the right side
of the defective drive to pop out the drive handle.
To view the hard drive arrays and remove the defective drive
from the SonicWALL CDP appliance, perform the following
steps:
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 47
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting the Replacement Drive into the SonicWALL CDP
Appliance
Warning: Be careful to remove only the defective drive from
the drive array while the appliance is powered on.
Removing more than one drive from an active
array will cause loss of data.
Warning: Do not insert anything other than the SonicWALL
approved hard drive into the SonicWALL CDP
appliance.
4. Grasp the drive handle and pull the drive straight out to
remove it from the slot.
To view the hard drive array and insert the replacement drive
into the SonicWALL CDP appliance, perform the following
steps:
On the System > RAID page, the removed drive is
indicated by an empty, black slot in the drive array. A status
of DEGRADED is still displayed for the array.
1. Remove the hard drive and the drive number stickers from
the replacement drive shipping carton.
2. Depending on which drive you are replacing, apply the
appropriate sticker to the drive handle. While holding the
drive with the label side up, place the sticker near the edge
of the handle next to the square button.
3. In the Web management interface, navigate to the
System > RAID page.
Page 48 Replacing a Single Hard Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Pop open the drive handle on the new hard drive by
pressing the square button.
5. Insert the drive into the empty slot, label side up with the
handle sticking out.
6. Press the drive firmly into place to seat the connectors, and
then close the handle.
8. You may continue to use your SonicWALL CDP appliance
while the RAID controller rebuilds the array with the new
drive.
The rebuilding process requires at least six hours and
could take several times longer, depending on the amount
of data contained in the array.
7. As the System > RAID screen refreshes (every 30
seconds), you will see the status change to
REBUILD-PAUSED.
Warning: There is a noticeable performance degradation of
the RAID array while it is being rebuilt.
When finished rebuilding, the drive LED changes to green
and the status for the array changes to OK.
The status changes to REBUILDING within a few minutes.
9. Re-install the front bezel, being sure to properly line up the
LCD connectors.
The best practice is to align and seat the right side of the
bezel (as you are facing the front of the SonicWALL CDP
appliance), then view the connectors from above as you
carefully press the left side of the bezel into place.
10. Lock the bezel with the front bezel security key.
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 49
Download from Www.Somanuals.com. All Manuals Search And Download.
BMSI Statement
FCC Part 15 Class A Notice
This equipment was tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy. And if
not installed and used in accordance with the instruction
manual, the device may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user is required to correct the interference at his own expense.
VCCI Statement
Notice About Modifying Equipment
Caution: Modifying this equipment or using this equipment
for purposes not shown in this manual without the written
consent of SonicWALL, Inc. could void the user’s authority to
operate this equipment.
Canadian Radio Frequency Emissions Statement
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
Page 50 FCC Part 15 Class A Notice
Download from Www.Somanuals.com. All Manuals Search And Download.
CISPR 22 (EN 55022) Class A
Regulatory Information for Korea
Complies with EN 55022 Class A and CISPR 22 Class A. This
is a class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be
required to take adequate measures.
Certificate Number SWL-2RK02-067
Declaration of Conformity
Application of Council
Directive
2004/108/EC (EMC) and 2006/95/EC
(LVD)
All products with country code “” (blank) and “A” are made in the
USA.All products with country code “B” are made in China.
Standards to which
conformity is declared
EN 55022 (2006) +A1 (2007) Class A
EN 55024 (1998) +A1 (2001), +A2 (2003)
EN 61000-3-2 (2006)
All products with country code “C” or “D” are made in Taiwan
R.O.C.
EN 61000-3-3 (2008)
EN 60950-1 (2006) +A11
National Deviations: AR, AT, AU, BE, CA,
CH, CN, CZ, DE, DK, FI, FR, GB, GR,
HU, IL, IN, IT, JP, KE, KR, MY, NL, NO,
PL, SE, SG, SI, SK, US
SonicWALL CDP 6080 / 6080B Getting Started Guide Page 51
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright Notice
© 2012 SonicWALL, Inc.
All rights reserved.
Trademarks
SonicWALL is a registered trademark of SonicWALL, Inc.
Microsoft Windows 7, Windows Vista, Windows XP, Windows
Server 2003, Windows Server 2008, Internet Explorer, and
Active Directory are trademarks or registered trademarks of
Microsoft Corporation.
Under the copyright laws, this manual or the software described
within, can not be copied, in whole or part, without the written
consent of the manufacturer, except in the normal use of the
software to make a backup copy. The same proprietary and
copyright notices must be affixed to any permitted copies as
were affixed to the original. This exception does not allow
copies to be made for others, whether or not sold, but all of the
material purchased (with all backup copies) can be sold, given,
or loaned to another person. Under the law, copying includes
translating into another language or format.
Other product and company names mentioned herein may be
trademarks and/or registered trademarks of their respective
companies and are the sole property of their respective
manufacturers.
Specifications and descriptions subject to change without
notice.
Page 52 Copyright Notice
Download from Www.Somanuals.com. All Manuals Search And Download.
SonicWALL, Inc.
2001 Logic Drive
San Jose CA 95124-3452
T +1 408.745.9600
F +1 408.745.9300
P/N 232-002104-50
Rev A 2/2012
DYNAMIC SECURITY FOR THE GLOBAL NETWORK™
©2012 SonicWALL, Inc. is a registered trademark of SonicWALL, Inc. Other product names mentioned herein may be trademarks and/or registered trademarks of their respective companies. Speci cations and descriptions subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|