|
RKP21x-208KVM Series
RKP241x-208KVM Series
USER’S MANUAL
WHERE TO BUY
1933 O'Toole Ave, #A107
San Jose, CA 95131, USA
Toll Free Tel: (866)955-0598
email: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for purchasing RKP215-208KVM Rackmount LCD Keyboard Drawer with 8 ports KVM
switch. LCD Keyboard Drawer with 8 ports KVM switch is ideal for application where space is
critical.
RKP215-208KVM is a combination of keyboard, trackball, KVM switch and TFT LCD packed into
a drawer with features such as monitor flip up design, adjustable mounting brackets, built in LCD
OSD, centralized control of 8 PCs.
Features
• Unique mechanical design to maximize rack mountable space
• Unique monitor flip up design allows viewing through closed glass door of cabinet
• Adjustable mounting brackets for multiple depth cabinets between 650mm and 1000mm
• Lightweight aluminum construction – with a black anodize finish
• High quality keyboard with integrated trackball
• Keyboard options supporting twelve languages
• Side to side wide-angle viewing as CRT monitor
• Built in On Screen Display controlled by integral membrane switches
• Power saving feature for prolonging the life of LCD panel
• Standard D-sub 15-pin VGA input connector
• Front-access lock for security
• EMC shielding around the monitor housing to minimize interference
• All mounting hardware included
• Built in KVM switch function for easy controlling and monitoring up to 8 residing servers
• Support eight character password protection and search PC server name
• Auto scan mode for monitor PCs and flexible scan time from 5 ~ 99 sec
• LED display for easy status monitoring
• Supplied with eight screened cables 6 ft long
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing Contents
RKP215-208KVM LCD Keyboard Drawer with KVM switch
User’s manual
AC to DC Power Adapter w/power cord
Rack Mount Kit
1 PCS
1 PCS
1 PCS
1 SET
8 PCS
Standard 3-in-1 KVM cable
Before Unpacking
It is very important to locate the LCD Keyboard Drawer with KVM switch in a suitable environment.
z
z
z
The surface for placing and fixing the LCD Keyboard Drawer with KVM switch should be
stable and level or mounted into a suitable cabinet.
Make sure the place has good ventilation, is out of direct sunlight, sway from sources of
excessive dust, dirt, heat, water, moisture and vibration.
Convenience for connecting the LCD Keyboard Drawer with KVM switch to the related
facilities should be well considers too.
Unpacking
The LCD Keyboard Drawer with KVM switch comes with the following standard parts shown as
below. Check and make sure they are included and in good condition. If anything is missing, or
damage, contact the supplier immediately.
Connection
The DC Power inlet and connection cables are located in the lower rear panel of the LCD
Keyboard Drawer.
1. DC Power Inlet f
2. VGA port
:
:
:
:
plug in the AC to DC Power Adapter
Connect to VGA port in computer
Connect to keyboard port in computer
Connect to mouse port in computer
3. PS/2 Keyboard cable
4. PS/2 Mouse cable
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safeguards
Please read all of these instructions carefully before you use the device.
Save this manual for future reference.
z
z
Unplug the LCD Keyboard Drawer with KVM switch from the power outlet before cleaning.
Do not spray liquid cleaners or aerosol directly on the device. Wet a cloth with a neutral detergent (e.g. clean
water) and squeeze it tight, then clean the screen slightly with it.
z
z
z
Do not expose the LCD Keyboard Drawer with KVM switch directly to rain, water, moisture or sunlight.
Avoid pressure on the LCD screen to prevent permanent damage to the display.
Do not attempt to service the device yourself. Improper operation may void your warranty. Refer all servicing to
qualified service personnel.
z
z
Safe storage environment of the LCD Keyboard Drawer with KVM switch is ranging between –20oC and 60oC.
Permanent damage could occur if the LCD Keyboard Drawer with KVM switch is stored outside the safe range.
Unplug the LCD Keyboard Drawer witch KVM switch immediately and call a qualified service personnel under
the following conditions:
1.
2.
3.
The VGA signal cord is frayed or damaged.
If the monitor has been exposed to rain, liquid or water.
If the monitor has been dropped or the casing has been damaged.
What the warranty does not cover
1.
Any product, on which the serial number has been defaced, modified or removed.
2.
Damage, deterioration or malfunction resulting from:
a)
Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
Repair or attempted repair by anyone not authorized by us.
Any damage of the product due to shipment.
b)
c)
d)
e)
f)
Removal or installation of the product.
Causes external to the product, such as electric power fluctuation or failure.
Use of supplies or parts not meeting our specifications.
Normal wear and tear.
g)
h)
Any other causes which does not relate to a product defect.
3.
Removal, installation, and set-up service charges.
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Session
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
On Screen Display - OSD
„
OSD is the convenient way for a user to adjust the screen performance to his satisfaction.
Menu / Selection
Left
Right
1. Entering the OSD Meun
2. Press the
3. Selecting icons for adjusting
4. Use buttons to scroll through the icons within the main menu and other sub-menus
the currently selected icon will be highlighted.
to display the OSD main menu.
5. A slider bar is displayed whenever a value is to be sent. Use
the bar.
buttons to scroll along
6. Saving the settings and Exit
7. Selections / selected values is automatically saved once made.
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Select “Auto” for autoadjust LCD quality
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the Settings
1. Brightness
• To perform brightness adjustment of the input RGB signal
2. Contrast
• To adjust the contrast level of the input signal
3. Phase
• To optimize the picture quality by adjusting the sampling clock of the input RGB Signal
4. Frequency
• To adjust the frequency of the input signal to optimize the picture quality
5. H - Position
• To adjust the horizontal position of the frame
6. V - Position
• To adjust the vertical position of the frame
7. Sharpness
• To enhance more sharpening on the appearance of images
8. Color Temperature
• To enter into the Color temperature sub-menu
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
• To adjust the horizontal position of the OSD frame
2. V - Position
• To adjust the vertical position of the OSD frame
3. Half Tone
• To switch the OSD color from full color to half tone
4. OSD Timeout
• To modify the duration of the OSD time-out
H - Position
1.
• To display the existing input signal information
2. Reset
• To reset the LCD to factory setting
Information
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Half Tone
• To switch LCD power ON/OFF auto mode
Resolution Setting
Step 1 – Press right click on the desktop
Step 2 – Choose “Properties”
Step 3 – change the “Screen Resolution”
Step 4 – change the “Screen refresh rate”
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
FAQ
„ My display doesn’t work, even though the computer appears to work
1. Make sure the power cable is securely plugged into the display
2. Make sure the display is turned on
3. Try turning the display off and then turning it on again
4. Make sure the display’s power cord is plugged into a power outlet and into the
AC power adapter. Check to see whether the outlet works by plugging
another device into the outlet
5. Check the connection between the display and the computer, The cable
connectors must be pushed in all the way
„ The message “Check Cable” appears on my display
1. This message appears when the video cable is not properly connected to the
computer
2. Make sure the analog video cable is plugged into the Analog Video Input port
on the back of the display
3. Make sure the other end of analog video cable is plugged into the PC’s video
port
„ The message “No Sync” appears on my display
1. This message appears when there is no video signal from the computer
a. with cable already connected
2. Make sure that the computer’s power is turn on
3. Make sure that your graphic card has its output already
„ The message “Signal Out of Range” appears on my display
1. This message appears when the input signal is beyond the display’s
capability
2. 13.3” 1024 x 768 at 70Hz (Max.)
3. 15.1” 1024 x 768 at 75Hz (Max.)
4. 17.1” 1280 x 1024 at 75Hz (Max.)
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
FAQ – Sun Server
„ Sun Server are using resolution at 1152 x 900 x 76Hz
„ Supported resolution mode
„ 640 x 480 x 70/75Hz
„ 800 x 600 x 70/75Hz
„ 1024 x 768 x 70/75Hz
„ 1280 x 1024 x 75Hz (17” LCD)
„ Note the Max. frequency of 13.3” is 70Hz
„ You need to change the Sun Server resolution before you connect to LCD
Display
„ Please do the following procedure to change the resolution setting :
1. as root:
you may find the following comment “/user/sbin/m64config”
2. Type “/user/sbin/m64config – prconf”
to view current resolution
3. Type “/user/sbin/m64config – res 1024x768x70 now”
to change to 1024x768 @ 70MHZ
4. the screen will be rubbish
5. Then type “pkill Xsun”
6. And Type “pkill Xsession” to restart the Xsession
Remember this process need to RESTART the server
„ Under Common Desktop Environment (CDE)
„ To change the OpenBoot resolution, you can type the following commend in OK prompt
1. In OK prompt, type “setenv output-device screen:r1024x768x70”
2. Type “printenv” to confirm the resolution has been changed to 1024x768x70Hz
3. Then type “reset” to restart the system
Remember this process need to RESTART the server
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
LCD
Size
17”
Screen Type
Display Area
Contrast Ratio
Viewing Angle
Resolution
Pixel pitch
Response Time
Brightness
Panel Color
Back Light
TFT Active Matrix
337.92mm(H) x 270.336mm(V)
350 : 1
150{ (H) x 125{ (V) Typ.
XGA 1280 x 1024
0.264mm (H) x 0.264mm (W)
Tr=5ms, Tf=20ms Typ
250 cd/m2
16.7M Colors
4 Lamps
Video
Synchronization
Range
Input Signal
Horizontal : 31-69 KHz
Vertical : 56-75 Hz
Analog RGB 0.7Vp-p
Power Management
Control
VESA DPMS
Power
OSD Control
Micro on/off switch on the backside
Brightness, Contrast, Color,
H position, V position, Auto config,
OSD adjust, Dither, etc.
External Connection
LCD
Power Input
Video Input
12V/5A DC adapter
15-pin D-Sub connector
Size
15”
Screen Type
Display Area
Contrast Ratio
Viewing Angle
Resolution
Pixel pitch
Response Time
Brightness
Panel Color
Back Light
TFT
304.1mm(H) x 228.1mm(V)
300 : 1
130{ (H) x 110{ (V) Typ
1024 x 768
0.297mm (H) x 0.297mm (W)
Tr=5ms, Tf=20ms Typ
250 cd/m2
16.2M
4 CCFTs (Cold Cathode Fluorescent
tube)
Video
Synchronization
Range
Input Signal
Horizontal : 48.36-60 KHz
Vertical : 56-75 KHz
Analog RGB 0.7Vp-p
Power Management
Control
VESA DPMS
Power
OSD Control
Micro on/off switch on the backside
Brightness, Contrast, Color,
H position, V position, Clock, Phase,
Auto config, Scaling, Input select,
Clear EEPROM, Multi window,
OSD adjust, Save
External Connection
Power Input
Video Input
12V/5A DC adapter
15-pin D-Sub connector
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
KVM Session
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
KVM
Bank Button
Channel Button
PS/2 Cable:
„ Mini Din 6 pin Male to Male
VGA Cable:
„ HDB15 pin Male to Male
Installation
Before installation, please make sure all of peripherals and computers have been turned off.
1. Connect the Keyboard, VGA, Mouse cables to the computer ports of KVM switch
2. After Powering on computers and finishing the boot-up process, you can start to go KVM
switch.
Note:
Please don’t switch the PC port (i.e. Don’t press the push button of KVM switch or run hot key)
during the computers are under boot-up process.
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Startup
1. Power on the KVM power
2. 7 segments LED is on
3. Key-in the password, default is “00000000”
4. If you forget your password, please send back to Manufacturer / Distributor
5. Pressing
to view all port
„
„
1
8
2
3
6
4
5
7
LED Indication
„ When you change the channel
„ If the PC is turn off or is disconnected
„ The LED will flash otherwise is will lit
Keyboard hot key command
„ Simple key sequence
„ Press “ Scroll Lock” twice within 2sec
„ Follow with a beep sound, going into the hot key mode
„ Need to key in the hot key within 2 sec
„ Go back to Operation System Control state
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Hot Key
„ Press “Bank” & “Channel” at the same time to reset the KVM switch to default
setting
• S.L. + S.L. +
• S.L. + S.L. +
Previous Channel
Next Channel
Note: You also could press “up arrow key” or “down arrow key” longer time to speed
up selecting the destination port
• S.L. + S.L. +
Page Up Previous Bank
• S.L. + S.L. + Page Down
Next Bank
„ To Select PC port
• S.L. + S.L. + Bank No. + Port No.
• Bank No. 1 – 8 (Max.) Port No. 01 – 16 (Max.)
• Example we select Bank 3 Channel 14
• S.L. + S.L. + 3 + 14
• Example we select Bank 7 Channel 5
• S.L. + S.L. + 7 + 05
„ Beeper On/Off
• S.L. + S.L. + B (Default is On)
„ Auto Scan
• S.L. + S.L. + S (Default is 10 sec from P to P)
• Press any key to stop
ROM REFLASH
• S.L. + S.L. + R (Refresh to OSD Default Value)
• Not include the PASSWORD
„ Rom Refresh
„ Find by PC name
• S.L. + S.L. +F
F I N D : █
• Key the PC name
• Search PC name starting from 1st PC port
„ OSD Menu
• S.L. + S.L. + Spacebar
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD Menu
„ Bank No.
BANK : 1
01
03
05
07
SYSTEM 01
“SYSTEM 02 (
02
04 “SYSTEM 04
06 SYSTEM 06
08 “SYSTEM 08
“SYSTEM 03
“SYSTEM 05
SYSTEM 07
„ PC Name List
OSD : 1 0 SEC. CHANGE PASSWORD
SCAN: 1 0 SEC. CONSOLE ON/OFF
„ KVM Settings
ESC : QUIT
TAB : NEXT
ENTER :COMPLETE
INSERT :EDIT
„ Info.
Ç/È: SELECT PORT
PgDn/PgUp: BANK SELECT
„ Use “Tab” key to select items like Bank, OSD, SCAN, CHANGE PASSWORD,
CONSOLE ON/OFF, etc…
„ Use Page Up & Page Down to switch previous or next bank
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD Menu
• PC Name List
• ““” near to the PC name represents the
PC system is powered on
BANK : 1
• Use up arrow key “Ç” or down arrow key
“È” to select port for destination PC
name and press “Enter” to select
• Edit PC name
• Press “Ins” key for editing PC name
• PC name should not more than 8
characters
01
03
05
07
SYSTEM 01
“SYSTEM 02 (
02
04 “SYSTEM 04
06 SYSTEM 06
08 “SYSTEM 08
“SYSTEM 03
“SYSTEM 05
SYSTEM 07
• After finish edit press “Enter”
OSD : 1 0 SEC. CHANGE PASSWORD
SCAN: 1 0 SEC. CONSOLE ON/OFF
• OSD – 10 sec
ESC : QUIT
TAB : NEXT
ENTER :COMPLETE
INSERT :EDIT
• OSD window display or PC
name exist 10 sec
• Default Value is 10 sec
• Modify from 05 – 99 sec
Ç/È: SELECT PORT
PgDn/PgUp: BANK SELECT
• Scan – 10 sec
• Scan interval from one PC
port to next PC port is 10
sec
• Default Value is 10 sec
• Max. 99 sec
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD - Password
ENTER PASSWORD : █
• Changing Password
• Default password “00000000”
• Choose “Change Password”
• Key-in the existing password
• Enter the New Password
• Re-Enter the New Password
• Changing Password
complete
ENTER NEW PASSWORD : █
ESC : QUIT ENTER : COMPLETE
• Max. 8 digits
RETYPE NEW PASSWORD : █
ESC : QUIT ENTER : COMPLETE
NEW PASSWORD COMPLETE
ESC : QUIT ENTER : COMPLETE
Console On/OFF
„ ON – any user can the console
„ OFF – user is not allow to use the console, unless key-in password
„ Default – OFF, you need to key-in password
Escape
102
?SYSTEM 02
„ PC name show in the up-left corner
„ Press “Esc” key to dear the message right away of OSD menu
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Cascade
Using 3 in 1 KVM cable connect from Bank 1’s “Cascade port” to Bank 2’s “Console port”. After
connected please press “Bank” & “Channel” button on the front of the KVM switch to reset the
KVM switch.
Bank 1
Bank 2
Bank 3
Bank 8 (Max)
„ Cascade level Max. 8 level
„ Max. PC connection is 128 (all using 16 ports)
„ All KVM switch is compatible & can cascade with each other
„ Using 3 in 1 KVM cable to cascade
„ Normal distance from one KVM to another is 15ft
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
FAQ
1. Don’t press any keys on the keyboard while the selected computer is booting up.
Otherwise, it might cause the keyboard error or keyboard is not detected at PC
side.
2. The computer boot up fine, but keyboard doesn’t work
z Make sure the keyboard works when directly plugged into the computer.
z Try a different keyboard, but use only 101, 102 or 104-key keyboard.
3. The Mouse is not detected during PC boot up.
z Make sure the mouse works when directly plugged into the computer.
z Make sure the mouse is a true PS/2 mouse. A combo mouse will work just as
long as it is set for PS/2 mode with the correct adapter. Try a different mouse.
z Avoiding moving the mouse or pressing the mouse buttons when switching
ports.
z Avoiding switching ports during shutting down the PC process.
z When you switch one PC port to another PC port, the best scan time setting
need to be set to 5 sec. or more. Normally, the VGA monitor change one
resolution mode to another will take one or two seconds. So, the scan time is
not recommended to below 5 seconds.
4. Sun Server connection problem
KVM switch are using standard PS/2 type keyboard and mouse and D-sub 15pin VGA for
connection. If you need to connect Sun Server to KVM switch, you need a separate converter kit.
Sun – 21 Kit
„ Convert Sun Micro Din 8 pin Keyboard & Mouse to Standard
Din 6 pin P/S 2 Keyboard & Mouse
„ Convert Sun micro 13W3 VGA to D-sub 15 pin Standard VGA
„ For old model Sun Micro Server
Sun – 31 Kit
„ Convert USB to P/S 2 Keyboard & Mouse
„ New model Sun Micro Server are using D-sub 15 pin
Standard VGA
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
8 Ports KVM Switch
PC Port
8
PC Port Connector
(All Female Type)
PS/2 Keyboard mini Din 6 pin
PS/2 Mouse Mini Din 6 pin
VGA HDDB 15pin
Daisy Chain Port Connector
(All Female Type)
PS/2 Keyboard mini Din 6 pin
PS/2 Mouse Mini Din 6 pin
VGA HDDB 15pin
PC selection
On Screen Display Manual, Hot Key, Push Button
7 segment LED
On Screen Display Control
Scan Intervals
One Bank LED, Two PC Port LEDs
Yes
5~99 Sec.
Keyboard Emulation
Mouse Emulation
VGA Resolution
Bandwidth
PS2
PS2
1920X1440
200MHz
Daisy Chain MAX Level
MAX PC Connection
Housing
8 levels
120
Metal
Power Adapter
DC 12V 1A or DC 9V 1A
Operation Temperature
Storage Temperature
Humidity
0~40℃
-20 ~ 60℃
0~80%, Non-Condensing
19” Rack Mount / 1RU
Size
Rev. JUL-02
Download from Www.Somanuals.com. All Manuals Search And Download.
|