LCD Projector
NP3150/NP2150/NP1150
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Safety Cautions
Precautions
Please read this manual carefully before using your NEC NP3150/NP2150/NP1150 projector and keep the manual
handy for future reference.Your serial number is located on the right side of your projector. Record it here:
CAUTION
To turn off main power, be sure to remove the plug from power outlet.
The power outlet socket should be installed as near to the equipment as possible, and should be easily
accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical
shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.
This symbol alerts the user that important information concerning the operation and maintenance of this
unit has been provided.
The information should be read carefully to avoid problems.
WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE
PRONGS CAN BE FULLY INSERTED.
DOC Compliance Notice (for Canada only)
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Acoustic Noise Information Ordinance-3. GSGV (for Germany only):
The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.
This label is on the side of the remote control.
This mark is on the top of the remote control.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may re-
sult in hazardous radiation exposure.
CAUTION
Do not look into the laser pointer while it is on and do not point the laser beam at a person. Serious in-
jury could result.
CAUTION
Avoid displaying stationary images for a prolonged period of time.
Doing so can result in these images being temporarily sustained on the surface of the LCD panel.
If this should happen, continue to use your projector. The static background from previous images will
disappear.
WARNING TO CALIFORNIA RESIDENTS:
Handling the cables supplied with this product will expose you to lead, a chemical known to the State of Califor-
nia to cause birth defects or other reproductive harm. Wash hands after handling.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Disposing of your used product
EU-wide legislation as implemented in each Member State requires that used electrical and electronic
products carrying the mark (left) must be disposed of separately from normal household waste. This in-
cludes projectors and their electrical accessories or lamps. When you dispose of such products, please
follow the guidance of your local authority and/or ask the shop where you purchased the product.
After collecting the used products, they are reused and recycled in a proper way. This effort will help us
reduce the wastes as well as the negative impact such as mercury contained in a lamp to the human
health and the environment at the minimum level.
The mark on the electrical and electronic products only applies to the current European Union Member
States.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
RF Interference (for USA only)
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT
those specified by NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government
regulation could void your right to operate this equipment. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
For UK only: In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use
with this equipment. If a power cable is not supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read
them carefully and heed all warnings.
Installation
• Do not place the projector in the following conditions:
- on an unstable cart, stand, or table.
- near water, baths or damp rooms.
- in direct sunlight, near heaters or heat radiating appliances.
- in a dusty, smoky or steamy environment.
- on a sheet of paper or cloth, rugs or carpets.
• If you wish to have the projector installed on the ceiling:
- Do not attempt to install the projector yourself.
- The projector must be installed by qualified technicians in order to ensure proper operation and reduce the
risk of bodily injury.
- In addition, the ceiling must be strong enough to support the projector and the installation must be in accor-
dance with any local building codes.
- Please consult your dealer for more information.
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 10 degrees, nor should the projector be installed in any way other
than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
10˚
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Fire and Shock Precautions
• Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside
your projector. Allow at least 4 inches (10cm) of space between your projector and a wall.
• Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become heated while
the projector is turned on.
• Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not attempt to
retrieve any objects that might fall into your projector. Do not insert any metal objects such as a wire or screw-
driver into your project. If something should fall into your projector, disconnect it immediately and have the object
removed by a qualified service personnel.
• Do not place any objects on top of the projector.
• Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.
• The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz. Ensure that your power supply
fits this requirement before attempting to use your projector.
• Do not look into the lens while the projector is on. Serious damage to your eyes could result.
• Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the
lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can cause
unpredictable outcome such as fire or injury to the eyes.
• Do not cover the lens with the black lens cap or equivalent while the projector is on. Doing so can lead to melting
of the cap and possibly burning your hands due to the heat emitted from the light output.
• Do not place any objects, which are easily affected by heat, in front of the projector lens or a projector exhaust
vent.
Doing so could lead to the object melting or getting your hands burned from the heat that is emitted from the light
output and exhaust.
• Handle the power cable carefully. A damaged or frayed power cable can cause electric shock or fire.
- Do not use any power cables than the supplied one.
- Do not bend or tug the power cable excessively.
- Do not place the power cable under the projector, or any heavy object.
- Do not cover the power cable with other soft materials such as rugs.
- Do not heat the power cable.
- Do not handle the power plug with wet hands.
• Turn off the projector, unplug the power cable and have the projector serviced by a qualified service personnel
under the following conditions:
- When the power cable or plug is damaged or frayed.
- If liquid has been spilled into the projector, or if it has been exposed to rain or water.
- If the projector does not operate normally when you follow the instructions described in this user’s manual.
- If the projector has been dropped or the cabinet has been damaged.
- If the projector exhibits a distinct change in performance, indicating a need for service.
• Disconnect the power cable and any other cables before carrying the projector
• Turn off the projector and unplug the power cable before cleaning the cabinet or replacing the lamp.
• Turn off the projector and unplug the power cable if the projector is not to be used for an extended period of time.
• When using a LAN cable:
For safety, do not connect to the connector for peripheral device wiring that might have excessive voltage.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
CAUTION
•
Always carry your projector by the carrying handle. Before doing so, be sure to lock the carrying handle in place.
To lock the carrying handle, see “To lock the carrying handle” on page 6.
• Do not use the tilt-foot for purposes other than originally intended. Misuses such as using the tilt foot to carry
or hang (from the wall or ceiling) the projector can cause damage to the projector.
• Do not send the projector in a soft case by parcel delivery service or cargo shipment. The projector inside the
soft case could be damaged.
• Select [HIGH] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select
[SETUP - OPTIONS]
[FAN MODE]
[HIGH].)
→
→
• Before using Direct Power Off, be sure to allow at least 20 minutes immediately after turning on the projector
and starting to display an image.
• Do not unplug the power cable from the wall outlet or projector when the projector is powered on. Doing so can
cause damage to the AC IN connector of the projector and (or) the prong plug of the power cable.
To turn off the AC power supply when the projector is powered on, use a power strip equipped with a switch
and a breaker.
• The projector can be unplugged during its cool down period after it is turned off.
Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become heated
while the projector is turned on and immediately after the projector is turned off.
• Do not turn off the AC power for 60 seconds after the lamp is turned on and while the POWER indicator is
blinking green. Doing so could cause premature lamp failure.
Caution on Handling the Optional Lens
When shipping the projector with the optional lens, remove the optional lens before shipping the projector. The lens
and the lens shift mechanism may encounter damage caused by improper handling during transportation.
Do not hold the lens part when carrying the projector.
Doing so could cause the focus ring to rotate, resulting in accidental dropping of the projector.
Remote Control Precautions
•
•
•
•
•
•
•
•
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
Do not heat, take apart, or throw batteries into fire.
If you will not be using the remote control for a long time, remove the batteries.
Ensure that you have the batteries’ polarity (+/–) aligned correctly.
Do not use new and old batteries together, or use different types of batteries together.
Dispose of used batteries according to your local regulations.
Lamp Replacement
•
•
To replace the lamp, follow all instructions provided on page 118.
Be sure to replace the lamp when the message [ThE LAmp hAS REAChED ThE END OF ITS USABLE LIFE.
pLEASE REpLACE ThE LAmp.] appears. If you continue to use the lamp after the lamp has reached the end
of its usable life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch
them as the pieces of glass may cause injury.
If this happens, contact your dealer for lamp replacement.
A Lamp Characteristic
The projector has a high-pressure mercury lamp as a light source.
A lamp has a characteristic that its brightness gradually decreases with age. Also repeatedly turning the lamp on
and off will increase the possibility of its lower brightness.
CAUTION:
When removing the lamp from a ceiling-mounted projector, make sure that no one is under the projector. Glass
fragments could fall if the lamp has been burned out.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
About High Altitude mode
•
Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600 me-
ters or higher.
Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH ALTI-
TUDE] can cause the projector to overheat and the protector could shut down. If this happens, wait a couple
minutes and turn on the projector.
•
•
Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTITUDE]
can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO].
Using the projector at altitudes approximately 5500 feet/1600 meters or higher can shorten the life of optical
components such as the lamp.
USB Wireless LAN Unit
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this
device may not cause harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B Personal Computer and Peripher-
al, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harm-
ful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment has been tested to comply with the limits for a Class B personal computer and peripheral, pursu-
ant to Subpart B of Part 15 of FCC Rules. Only peripherals (computer input/output devices, terminals, printers, etc.)
certified (DoC) or verified to comply with Class B limits may be attached to this equipment. Operation with non-
certified (DoC) or non-verified personal computer and/or peripherals is likely to result in Interference to radio and TV
reception.
The connection of a unshielded equipment interface cable to this equipment will invalidate the FCC Certification of
this device and may cause interference levels which Exceed the limits established by FCC for equipment.
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance
could void your authority to operate the equipment.
Regulatory Information/Disclaimers
Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the
user documentation provided with the product. Any changes or modifications (including the antennas) made to this
device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of
this device, or the substitution of the connecting cables and equipment other than manufacturer specified. It is the
responsibility of the user to correct any interference caused by such unauthorized modification, substitution or at-
tachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or viola-
tion of government regulations arising from failing to comply with these guidelines.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
CAUTION
To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be in-
stalled to provide a separation distance of at least 7.87"/20cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
SAR compliance has been established in typical laptop computer(s) with USB slot, and product could be used in
typical laptop computer with USB slot. Other application like handheld PC or similar device has not been verified
and may not compliance with related RF exposure rule and such use shall be prohibited.
Usage restrictions in North America
The following channels can be used indoors only.
•
In the United States and Canada: 36, 40, 44, and 48 channels
•
In Mexico: 149, 153, 157, 161, and 165 channels
The other channels can be used both indoors and outdoors.
This Class B digital apparatus complies with Canadian RSS-210.
Cet appareil numerique de la Classe B est conforme a la norme CNR-210 du Canada.
To comply with Canada RSS-210(Issue 7) section A9.4(b)(ii); this radio product will not transmit on any channels
operating in the exclusion band of 5600 - 5650MHz. All channels in the 5600 - 5650MHz band will be disabled by
factory firmware and is not user changeable.
Regulatory Statement:
Operation of this device is subjected to the following National regulations and may be prohibited to use if certain re-
striction should be applied.
France:
Outdoor use limited to 10mW e.i.r.p. within the band 2454 – 2483.5 MHz. Derogation in French overseas depart-
ments of Guyane and La Reunion: outdoor use not allowed in band 2400 - 2420 MHz.
Hereby, NEC Display Solutions, Ltd. declares that this USB Wireless LAN Unit (Model: NP01LM) is in compliance
with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Cautions on security when using wireless LAN products
With a wireless LAN, radio waves are used instead of LAN cables for the exchange of data between the wireless
access points (computers, etc.), offering the advantage that LAN connections can be made freely within the range
of the radio waves.
On the other hand, the radio waves reach all points within this range, regardless of walls or other obstacles, possi-
bly resulting in the problems described below if the proper security measures are not taken.
•
•
Contents of transmissions may be intercepted
Malicious third parties may purposely intercept the radio waves and steal information contained in the transmis-
sions, including such personal information as ID numbers, passwords, credit card numbers, e-mail messages,
etc.
Improper intrusions
Malicious third parties may without permission access the personal or company network and steal personal or
confidential information, pretend to be someone else and leak incorrect information, rewrite information that has
been intercepted, introduce computer viruses or otherwise damage data or the system, etc.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Wireless LAN cards and wireless access points generally include security measures for dealing with these prob-
lems. Making the proper security settings before using the products can reduce the risk of such problems arising.
We recommend that you fully understand the problems that can arise when using the products without making the
security settings, then that you make the security settings based on your own decision and at your own discretion.
Cautions on Usage
Warning
•
The USB Wireless LAN Unit is not meant for use with facilities or equipment involving the safeguard of hu-
man life, such as medical equipment, nuclear facilities or equipment, aeronautical or space equipment, trans-
portation facilities or equipment, etc., or with facilities or equipment requiring high levels of reliability. Do not
use the USB Wireless LAN Unit in such cases.
•
•
Do not use the USB Wireless LAN Unit near cardiac pacemakers.
Do not use the USB Wireless LAN Unit near medical equipment. Doing so may cause electromagnetic inter-
ference with the medical equipment, possible leading to death.
•
•
Do not disassemble or modify the USB Wireless LAN Unit in any way. Doing so could lead to fire or electric
shock.
Do not use the USB Wireless LAN Unit in wet or moist places, such as in bathrooms or near humidifiers. Do-
ing so could lead to fire, electric shock or malfunction.
Caution
To prevent damage due to static electricity, eliminate any static electricity from your body before touching the
USB Wireless LAN Unit.
•
Static electricity from the human body may damage the USB Wireless LAN Unit. Before touching the USB
Wireless LAN Unit, touch an aluminum sash, a door knob, or some other metal object around you to elimi-
nate the static electricity.
Caution
The radio waves used by the USB Wireless LAN Unit pass through the wood or glass used in normal homes (but
not through window panes with built-in metallic mesh).
The radio waves do not pass through iron reinforcing bars, metal or concrete, however, so the USB Wireless LAN
Unit cannot be used for communicating through walls or floors made with these materials.
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
What’s in the Box?......................................................................................................... 1
Congratulations on Your Purchase of the Projector ................................................. 2
Part Names of the Projector.......................................................................................... 4
Front/Top.................................................................................................................. 4
Rear......................................................................................................................... 4
Top Features............................................................................................................ 7
Terminal Panel Features.......................................................................................... 8
Operating Range for Wireless Remote Control...................................................... 10
Setting Up the Screen and the Projector..................................................................... 12
Making Connections.................................................................................................... 13
Connecting Your PC or Macintosh Computer......................................................... 13
Connecting Your VCR or Laser Disc Player ........................................................... 17
Turning on the Projector .............................................................................................. 22
Adjusting the Picture Size and Position....................................................................... 25
Adjusting the position of a projected image........................................................... 26
Adjusting Volume Up & Down...................................................................................... 31
Using the Laser Pointer............................................................................................... 32
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Turning off the Projector .............................................................................................. 33
Turning Off the Image and Sound................................................................................ 34
Changing Lamp Mode................................................................................................. 35
Using a USB Mouse.................................................................................................... 36
Cornerstone........................................................................................................... 39
Assigning a Keyword for the first time.................................................................... 44
Limiting Access Level to Available Menu Items........................................................... 49
Operation Using an HTTP Browser............................................................................. 52
Overview................................................................................................................ 52
DESKTOP]............................................................................................................. 59
Easy to use............................................................................................................ 64
Using Windows Explorer to save files.................................................................... 64
Operating the Viewer Function from the Projector (playback) ..................................... 65
Changing Background Logo........................................................................................ 69
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
S-VIDEO................................................................................................................ 75
[PICTURE]............................................................................................................. 78
[SOUND]................................................................................................................ 85
[BASIC].................................................................................................................. 86
[INSTALLATION] .................................................................................................... 92
[USAGE TIME]..................................................................................................... 111
[SOURCE (1)]...................................................................................................... 112
[SOURCE (2)]...................................................................................................... 112
[WIRED LAN]....................................................................................................... 113
[WIRELESS LAN (1)]........................................................................................... 113
[WIRELESS LAN (2)]........................................................................................... 114
Returning to Factory Default................................................................................ 115
Cleaning or Replacing the Filter................................................................................ 116
Cleaning the Cabinet and the Lens........................................................................... 117
Replacing with Optional Lens.................................................................................... 123
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Troubleshooting ......................................................................................................... 125
PC Control Codes and Cable Connection................................................................. 137
PC Control Codes................................................................................................ 137
Troubleshooting Check List........................................................................................ 141
TravelCare Guide....................................................................................................... 143
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
What’s in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your Projector.
P
O
W
O
E
R
R
FF
E
S
W
U
O
P
T
A
P
T
S
M
A
B
L
Y
V
S
B
U
D
ID
C
N
A
E
T
O
S /
N
O Y
C
O
S
1
M
P
-V
E
C
ID
R
U
T
U
O
M
O
E
S
O
E
R
P
P
O
T
O
S
N
E
U
2
W
E
J
D
N
A
O
O
T
N
R
T
U
A
M
R
O
3
F
V
IE
E
R
D
W
ER
3
N
ET
W
O
R
K
S
E
L
T
E
C
C
E
L
T
E
P
S
U
N
W
O
D
L
A
L
S
E
-
C
R
L
I
C
K
T
P
I
H
G
I
P
R
M
E
O
U
S
R
-
F
E
C
R
L
I
C
A
E
S
T
Z
K
F
P
E
E
E
L
C
T
L
A
M
V
P
O
M
O
L
U
D
M
E
E
A
U
M
T
O
A
G
A
N
D
I
J.
F
Y
P
A
G
PICTURE
E
E
U
P
P
I
C
D
O
-
M
W
N
U
T
3
D
R
E
F
O
R
M
HELP
remote control
Batteries (aa x 2)
(7n900801)
Projector
lens cap
(24ft9741)
remote Cable
Power cable
Vga signal cable
(7n520019)
(7n080204) Us
(7n080011) eU
(7n520052)
Cd-rOM
User’s manual and User supportware 5
(7n951122)/(7n951132)
• important infomation (7n8P8082)
• Quick setup guide (7n8P8072)
• Wired and Wireless network setup guide
(7n8P8092)
• security sticker
• anti-theft screw for lens x 1
(24V00841)
For North America only
Registration card
Limited warranty
For Europe only
Guarantee policy
Installed USB wireless LAN unit
North America: NP01LM3 (7N970062)
Europe: NP01LM2 (7N970061)
Joint module (9N999080)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Introduction to the Projector
This section introduces you to the NP3150/NP2150/NP1150 projector and describes key features and controls.
Congratulations on Your Purchase of the Projector
The NP3150/NP2150/NP1150 is a sophisticated XGA projector that produces an enhanced display. With the
NP3150/NP2150/NP1150 you will be able to project images up to 500" (measured diagonally). Enjoy crisp and
sharp large screen display from your PC, workstation or Macintosh computer, DVD player, VCR, satellite hookup,
HDTV source, as well as images from your USB storage device. The NP3150/NP2150/NP1150 provides for en-
hanced security options to help deter projector theft and provides for full projector control through the PC control
port (D-Sub 9 Pin) and LAN support. With input and output flexibility, long lamp life and a full function remote, the
NP3150/NP2150/NP1150 lets you enjoy larger than life viewing from a compact and easy to setup and use projec-
tor.
Features you’ll enjoy :
•
•
•
•
LCD projector with high resolution and high brightness
High resolution display - up to UXGA compatible, XGA native resolution.
Extensive optional lens
One standard lens and five types of optional lenses are available
Lens shift mechanism offers installation flexibility
Manual lens shift that can be adjusted by turning dials on the top of the projector
Direct power Off & Auto Start
The projector has a feature called “Direct Power Off”. This feature allows the projector to be turned off (even
when projecting an image) using a power strip equipped with a switch and a breaker.
NOTE: Before using Direct Power Off, be sure to allow at least 20 minutes immediately after turning on the projector and
starting to display an image.
Also, the power cable can be removed immediately after turning off the projector.
Auto Start eliminates the need to always use the POWER (ON/STANDBY) button on the remote control or pro-
jector cabinet.
•
Integrated RJ-45 connector for wired networking capability along with wireless networking capabilities
An RJ-45 connector and a USB Wireless LAN unit are equipped as standard features*.
Present from anywhere in the room when using as a wireless LAN projector and software contained on the sup-
plied User Supportware 5 CD-ROM, no physical signal cable connection to a PC is required.
NOTE: The NP3150/NP2150/NP1150 series projectors distributed in some areas and countries do not come standard with the
USB Wireless LAN Unit.
If you purchase the projector without the USB Wireless LAN Unit installed and need to present to the projector via a wireless
connection, the optional USB Wireless LAN Unit must be installed.
•
Windows Vista standard functions Network projector and Remote Desktop can be used
A Windows Vista-based computer can be operated using the projector over a network.
The projector supports the Network Projector function and the Remote Desktop function of Windows Vista.
A variety of input ports and a comprehensive array of system control interfaces
•
•
•
This projector supports input signals on the following ports: BNC, DVI-D, 15pin D-Sub, component, composite
and S-video.
Wall Color Correction
Built-in Wall Color Correction presets provide for adaptive color correction when projecting onto non-white
screen material (or a wall).
Six picture preset modes for user adjustable picture and color settings
Each picture preset mode can be customized and memorized according to your preference.
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
•
preventing unauthorized use of the projector
Enhanced smart security settings for password protection, cabinet control panel lock, and USB memory protec-
tion key to help prevent unauthorized access, adjustments and theft deterrence.
About this user’s manual
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to
review the user’s manual. This may save you time later on. At the beginning of each section of the manual you’ll find
an overview. If the section doesn’t apply, you can skip it.
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Part Names of the Projector
Front/Top
lens shift dial (right / left,Up / down)
page 26)
(
→
Controls
page 7)
(
→
R
E
W
U S
T
P O
A
P
T
S
M
A
L
Y
B
B
S
focus ring
page 27)
U
D
N
A
T
S /
N
O
E
C
R
U
O
S
T
S
U
J
D
A
O
T
U
A
(
→
M
R
O
F
E
R
D
3
T
C
E
L
E
S
U P
N
W
O
D
remote sensor
page 10)
Ventilation (inlet) / filter
page 116)
(
→
T
H
R I G
F T
(
→
S
S H I
N
F T
L E
L E
lens release Button
page 123)
Built-in security slot ( )*
(
→
lens
Ventilation (inlet) / filter
page 116)
(
→
Zoom lever
adjustable tilt foot lever
page 28)
(
page 27)
→
(
→
lens Cap
adjustable tilt foot
page 28)
(
→
*
This security slot supports the MicroSaver® Security System. MicroSaver® is a registered trademark of Kens-
ington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.
Rear
L
L
E
E
F
N
S
T
S
H
IF
T
RIG
H
T
stereo speaker (5W x 2)
DO
W
N
U
P
SELECT
UsB Wireless lan unit
the model without the UsB
wireless lan unit has a dummy
cover here.
3D
R
E
FO
R
M
AU
T
O
AD
JU
S
T
SOUR
CE
ON
/S
T
AN
D
U
SB
B
L
A
Y
M
S
P
T
AT
U
S
PO
W
E
R
W
I
R
E
L
E
S
S
S
S
E
L
E
R
I
W
Ventilation (outlet)
heated air is exhausted from
here.
lamp Cover
page 118)
(
terminal Panel
→
(
→
page 8)
remote sensor
page 10)
(
→
Main Power switch
When you plug the supplied power cable into an active
wall outlet and turn on the Main Power switch, the POW-
aC input
Connect the supplied power cable’s three-pin plug here,
and plug the other end into an active wall outlet.
er indicator turns orange and the projector is in standby
mode.
(
→
page 21)
(
→
page 22)
NOTE:
The USB Wireless LAN Unit emits weak radio waves when the projector is in standby* mode or turned on.
If you use the projector with the USB Wireless LAN Unit in the area where the use of wireless LAN equipment is prohibited, re-
move the USB Wireless LAN Unit from the projector. (→ page 139)
* To stop emitting radio waves from the USB Wireless LAN Unit during standby mode, select [POWER-SAVING] from [STANDBY
MODE].
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Bottom
anti-theft screw for lens
page 124)
Carrying handle
(
→
Carrying the Projector
Always carry your projector by the handle.
Ensure that the power cable and any other cables connecting to video sources are disconnected before moving the
projector.
When moving the projector or when it is not in use, cover the lens with the lens cap.
NOTE: To stand the projector on its end, do so by holding the cabinet, not by holding the carrying handle.
Doing so can cause damage to the carrying handle.
lock
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
To lock the carrying handle
1. Carefully place the projector on its end.
2. Pull up the carrying handle with the catch pressed down.
3. Press down the left and right locks to set the carrying handle
in place.
•
To place back the carrying handle, press up the left and right
locks and pull down the carrying handle.
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Top Features
9
10
8
7
6
1 4 5
SELECT
USB
LAMP
STATUS
POWER
3D.REFORM AUTO.ADJUST SOURCE
ON/STAND.By
11
12
3 2
1. pOWER Button (
ꢀꢀ, ꢀꢁ)
) (ON / STAND BY) ( page
ꢂ. SOURCE Button
ꢃ. AUTO ADJUST Button ( page ꢁ1)
→
→
NOTE: To turn on the projector, press and hold this button
for a minimum of two seconds. To turn off the projector,
press this button twice.
8. ꢁD REFORm Button ( page ꢀ9, ꢁ9)
→
9. mENU Button
ꢀ. pOWER Indicator ( page ꢀꢀ, ꢀꢁ, 1ꢀ5)
→
10. SELECT
/ Volume Buttons
ꢁ. STATUS Indicator ( page 1ꢀ5)
→
11. ENTER Button
1ꢀ. EXIT Button
4. LAmp Indicator ( page 118, 1ꢀ5)
→
5. USB Indicator
Lights when a USB memory is inserted into the USB
port.
NOTE: The USB indicator will not light when non-USB stor-
age devices such as USB mouse devices are inserted.
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Terminal Panel Features
4 13 12
3
2
USB(LAN)
14
5 6
7
1
8
9 11 10
The actual appearance of the terminal panel may differ slightly from that shown in the drawing, but this does not af-
fect the projector’s performance.
1. COmpUTER 1 IN/Component Connector (mini
D-Sub 15 pin) ( page 1ꢁ, 15)
9. AUDIO OUT (Stereo mini Jack) ( page 15)
→
→
10. pC CONTROL port (D-Sub 9 pin) ( page 1ꢁꢃ, 1ꢁ8)
→
AUDIO IN (Stereo mini Jack) ( page 1ꢁ, 14, 1ꢂ)
→
Use this port to connect your PC or control system
to control your projector via a serial cable. This
enables you to control the projector using serial
communication protocol. A commercially available
RS232C cross cable is required to use this port.You
can also control the projector by using PC Control
Utility 3.0 contained on the supplied User Support-
ware 5 CD-ROM. To do so you must first have PC
Control Utility 3.0 installed on your PC. If you are
writing your own program, typical PC control codes
are on page 1ꢁꢃ.
ꢀ. COmpUTER ꢀ IN/Component (R/Cr, G/Y, B/Cb, h,
V) Connectors (BNC x 5) ( page 1ꢁ)
→
AUDIO IN (Stereo mini Jack) ( page 1ꢁ)
→
ꢁ. COmpUTER ꢁ (DVI-D) IN Connector (ꢀ4 pin)
(hDCp compatible) ( page 14)
→
AUDIO IN (Stereo mini Jack) ( page 14)
→
4. COmpONENT IN (Y, Cb/pb, Cr/pr) Connectors
(RCA) ( page 1ꢂ)
→
AUDIO L/mONO, R (RCA) ( page 1ꢂ)
→
11. Remote Jack (Stereo mini Jack) ( page 11)
→
5. S-VIDEO IN Connector (mini DIN 4 pin) ( page
→
NOTE: Connecting the remote cable to the REMOTE mini
jack on the terminal panel will make the wireless operation
unavailable.
1ꢃ)
ꢂ. VIDEO IN Connector (RCA) ( page 1ꢃ)
→
ꢃ. VIDEO/S-VIDEO AUDIO L/mONO, R (RCA) ( page
→
1ꢀ. USB port (Type A) ( page ꢁꢂ)
→
1ꢃ)
1ꢁ. LAN port (RJ-45) ( page 18, 99)
→
8. mONITOR OUT Connector (mini D-Sub 15 pin)
14. USB Wireless LAN unit ( page 1ꢁ9)
→
(
→
page 15)
NOTE: A dummy cover is provided on this location of the
projector without the USB Wireless LAN Unit.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Part Names of the Remote Control
4. LED
T
C
E
L
E
S
Flashes when any button is pressed.
N E T W O R K
3
5. pOWER ON Button ( page ꢀꢀ)
→
V I E W E R
2
P O N E N T
C O M
O N
R
E
S - V I D E O
1
W
NOTE: To turn on the projector, press and hold the POWER
ON button for a minimum of two seconds.
O
P
C O M P U T E R
V I D E O
F
O F
R
E
W
O
P
3
1
ꢂ. pOWER OFF Button ( page ꢁꢁ)
→
NOTE: To turn off the projector, press the POWER OFF but-
ton twice.
2
ꢃ. COmpUTER 1 Button ( page ꢀ4)
→
1. Laser pointer
8. COmpUTER ꢀ Button ( page ꢀ4)
→
9. COmpUTER ꢁ Button ( page ꢀ4)
→
CAUTION:
* Do not look into the laser pointer while it is on.
* Do not point the laser beam at a person.
10. VIDEO Button ( page ꢀ4)
→
11. S-VIDEO Button ( page ꢀ4)
→
ꢀ. Infrared Transmitter
1ꢀ. COmpONENT Button ( page ꢀ4)
→
ꢁ. Remote jack ( page 11)
→
1ꢁ. VIEWER Button ( page ꢀ4, ꢂ4)
→
14. NETWORK Button ( page ꢀ4)
→
4
5
15. mENU Button
7
POWER
OFF
POWER
ON
1ꢂ. SELECT
Button
COMPUTER
6
10
11
1
2
VIEWER
VIDEO
8
1ꢃ. ENTER Button
18. EXIT Button
COMPONENT
13
3
S-VIDEO
NETWORK
14
19. LASER Button ( page ꢁꢀ)
→
12
9
ꢀ0. mOUSE R-CLICK Button ( page ꢁ8)
→
15
SELECT
ꢀ1. mOUSE L-CLICK Button ( page ꢁ8)
→
16
17
ꢀꢀ. FREEZE Button ( page ꢁ4)
→
18
19
ꢀꢁ. pIp Button ( page 4ꢀ)
→
LASER
ꢀ4. ASpECT Button ( page 8ꢁ)
→
L-CLICK
R-CLICK
21
22
23
ꢀ5. VOLUmE +/– Buttons ( page ꢁ1)
→
MOUSE
FREEZE
20
29
30
PIP
ꢀꢂ. pICTURE Button ( page ꢃ8, 80)
→
ASPECT LAMP MODE AUTO ADJ.
ꢀꢃ. pIC-mUTE Button ( page ꢁ4)
→
24
VOLUME MAGNIFY
PAGE
UP
ꢀ8. mAGNIFY +/– Buttons ( page ꢁ4)
→
31
25
DOWN
ꢀ9. LAmp mODE Button ( page ꢁ5)
→
PICTURE
PIC-MUTE
3D REFORM
32
33
26
27
ꢁ0. AUTO ADJ. Button ( page ꢁ1)
→
HELP
ꢁ1. pAGE Up/DOWN Buttons ( page ꢁ8)
→
ꢁꢀ. ꢁD REFORm Button ( page ꢀ9, ꢁ9)
→
ꢁꢁ. hELp Button ( page ꢁ5)
→
28
9
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Battery Installation
1 Press the catch and re-
ꢀ Install new ones (AA). Ensure
ꢁ
Slip the cover back over the bat-
teries until it snaps into place.
move the battery cover.
that you have the batteries’ po-
larity (+/–) aligned correctly.
NOTE: Do not mix different types of
batteries or new and old batteries.
2
2
1
1
Operating Range for Wireless Remote Control
remote sensor on projector cabinet
7m/22 feet
7m/22 feet
30°
30°
30°
30°
remote control
NOTE: Actual operating range may differ slightly from that shown in the drawing.
TIP: You can determine which remote sensor on the projector is enabled in wireless mode. The options are: front, rear or both. (→
page 110)
•
•
The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle
of the remote sensor on the projector cabinet.
The projector will not respond if there are objects between the remote control and the sensor, or if strong light
falls on the sensor.
Weak batteries will also prevent the remote control from properly operating the projector.
Remote Control Precautions
•
•
•
•
•
•
•
•
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
Do not heat, take apart, or throw batteries into fire.
If you will not be using the remote control for a long time, remove the batteries.
Ensure that you have the batteries’ polarity (+/–) aligned correctly.
Do not use new and old batteries together, or use different types of batteries together.
Dispose of used batteries according to your local regulations.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Using the Remote Control in Wired Operation
Connect one end of the supplied remote cable to the REMOTE mini jack and the other end to the remote jack on
the remote control.
NOTE: Connecting the remote cable to the REMOTE mini jack on the terminal panel will make the wireless operation unavailable.
REMOTE
USB(LAN)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
This section describes how to set up your projector and how to connect PCs, video and audio sources.
Your projector is simple to set up and use.
But before you get started, you must first:
1
z
x
Set up a screen and the projector.
Connect your computer or video equip-
ment to the projector. See pages 13 -
20.
c
Connect the supplied power cable.
See page 21.
ꢁ
NOTE: Ensure that the power cable and any
other cables are disconnected before moving the
projector. When moving the projector or when it
is not in use, cover the lens with the lens cap.
ꢀ
Setting Up the Screen and the Projector
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 30 inches (0.76 m) measured diagonally when the projector is roughly 41 inches (1.0 m) from the
wall or screen. The largest the image can be is 500 inches (12.7 m) when the projector is about 718 inches (18.2 m)
from the wall or screen. Use the drawing below as a guide.
Selecting a Location
Screen Size (unit: cm/inch)
609.6 (W) X 457.2 (H) / 240 (W) X 180 (H)
300
Screen Size
"
487.7 (W) X 365.8 (H) / 192 (W) X 144 (H)
406.4 (W) X 304.8 (H) / 160 (W) X 120 (H)
240
"
200
"
304.8 (W) X 228.6 (H) / 120 (W) X 90 (H)
243.8 (W) X 182.9 (H) / 96 (W) X 72 (H)
150
"
120
"
203.2 (W) X 152.4 (H) / 80 (W) X 60 (H)
162.6 (W) X 122.0 (H) / 64 (W) X 48 (H)
100
"
80"
60"
40"
121.9 (W) X 91.4 (H) / 48 (W) X 36 (H)
81.3 (W) X 61.0 (H) / 32 (W) X 24 (H)
Lens center
L
E
F
T
L
E
N
S
S
H
I
T
R
I
H
T
DOWN
U
P
10.9/429.1"
m/inch)
SELEC
T
.E
FORM
8.7/342.5"
AUTO
.ADJU
S
S
C
ON/S
T
AND
.By
USB
AMP
T
U
S
POW
S
E
T
A
L
R
I
7.3/287.4"
5.4/212.6"
4.3/169.3"
3.6/141.7"
L
S
S
L
R
1.4/
55.12"
14.2"
2.9/1
:
2.1/82.68"
Distance (Unit
TIP: The screen sizes above are intermediate values between tele (minimum display area) and wide (maximum display area) when
the standard lens is used. Image size can be adjusted with the zoom adjustment up to a maximum of 15%.
For optional lenses, see page 121.
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Making Connections
Connecting Your PC or Macintosh Computer
NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode
and before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or power manage-
ment software.
Enabling the computer’s external display
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on
or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through
external display selections.
COMPUTER 2 IN
NOTE: The COMPUTER 1 IN connector
supports Plug & Play (DDC2).
USB(LAN)
COMPUTER 1 IN
BnC X 5 cable (not supplied)
audio
cable (not
audio cable (not supplied)
Vga signal cable (supplied)
supplied)
to mini d-sub 15-pin connector on the
projector. it is recommended that you use
a commercially available distribution am-
plifier if connecting a signal cable longer
than the one supplied.
phONE
NOTE: For older Macintosh, use a commercially
available pin adapter (not supplied) to connect to
your Mac’s video port.
iBM Vga or Compatibles (notebook
type) or Macintosh (notebook type)
•
•
First turn off the computer and the projector before making connections.
Turn down the volume on the computer before connecting an audio cable to the headphone jack of the com-
puter. After connecting the computer to the projector, you can adjust the sound level on the computer and the
projector to your preference.
•
You are recommended to connect an audio cable to an audio out connector (mini jack type) if any.
NOTE: The NP3150/NP2150/NP1150 is not compatible with video decoded outputs of either the NEC ISS-6020 and ISS-6010 switchers.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan
converter.
This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.
* When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:
Project an image to fill the screen and then press the AUTO ADJ button on the remote control or the AUTO ADJUST button on
the projector cabinet.
* When noise appears on the sides of the screen:
Use the Overscan feature to display the image correctly.
Be sure to change the Overscan to 0% before pressing the AUTO ADJ or AUTO ADJUST button, otherwise an image may be
displayed with its sides cut off.
1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
When Viewing a DVI Digital Signal
To project a DVI digital signal, be sure to connect the PC and the projector using a DVI-D signal cable (not supplied)
before turning on your PC or projector. Turn on the projector first and select COMPUTER 3 from the source menu
before turning on your PC.
Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed.
Should this happen, restart your PC.
Do not disconnect the DVI-D signal cable while the projector is running. If the signal cable has been disconnected
and then re-connected, an image may not be correctly displayed. Should this happen, restart your PC.
NOTE:
• Use a DVI-D cable compliant with DDWG (Digital Display Working Group) DVI (Digital Visual Interface) revision 1.0 standard.
The DVI-D cable should be within 10 m (394") long.
• The DVI (DIGITAL) connector (COMPUTER 3 (DVI-D) IN) accepts VGA (640x480), SVGA (800x600), 1152x864, XGA (1024x768),
SXGA (1280x1024 @ up to 60Hz) and SXGA+ (1400x1050 @ up to 60Hz).
(dVi-d connector with hdCP)
COMPUTER 3 (DVI-D) IN
AUDIO IN
USB(LAN)
audio cable (not supplied)
dVi-d cable
(not supplied)
phONE
iBM Vga or Compatibles or Macintosh
What is hDCp/hDCp technology?
HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content Protection
(HDCP) is a system for preventing illegal copying of video data sent over a Digital Visual Interface (DVI).
If you are unable to view material via the DVI input, this does not necessarily mean the projector is not functioning
properly. With the implementation of HDCP, there may be cases in which certain content is protected with HDCP
and might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting an External Monitor
COMPUTER 1 IN (or COMPUTER 2 IN / COMPONENT IN)
USB(LAN)
AUDIO OUT
MONITOR OUT
audio cable (not supplied)
audio cable (not supplied)
Vga signal cable (supplied)
Vga signal cable (not supplied)
AUDIO
IN
phONE
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB analog
or component image you’re projecting.
NOTE:
• Daisy chain connection is not possible.
• The MONITOR OUT connector will output no video signal (Digital signal) from the COMPUTER 3 (DVI-D) IN connector.
• When audio equipment is connected, the projector speaker is disabled.
• When [NORMAL] is selected from [STANDBY MODE], the MONITOR OUT connector outputs the last displayed video signal and
the AUDIO OUT jack outputs the last audio signal. The sound level remains the same as the last one.
• Selecting [POWER-SAVING] in [STANDBY MODE] stops outputting a video signal from the MONITOR OUT connector during
standby mode. This causes the AUDIO OUT jack to stop outputting sound.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting Your DVD Player with Component Output
USB(LAN)
COMPONENT IN
AUDIO IN
Component video rCa
3
cable (not supplied)
audio equipment
dVd player
L
R
Y
Cb Cr
AUDIO IN
AUDIO OUT
Component
L
R
audio cable (not supplied)
TIP: A component signal will be automatically displayed. If not, from the menu, select [SETUP] → [OPTIONS] → [SIGNAL SE-
LECT] → [COMPUTER 1 (or 2)] → [COMPONENT].
•
When connecting to the COMPUTER 2 IN, use a commercially available RCA (female)-to-BNC(male) adapter.
NOTE: Refer to your DVD player’s owner’s manual for more information about your DVD player’s video output requirements.
1ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting Your VCR or Laser Disc Player
USB(LAN)
S-VIDEO IN
AUDIO IN
VIDEO IN
s-Video cable (not supplied)
Video cable (not supplied)
audio equipment
VCr/ laser disc player
S-VIDEO VIDEO
VIDEO OUT
L
R
AUDIO IN
AUDIO OUT
L
R
audio cable (not supplied)
NOTE: Refer to your VCR or laser disc player owner’s manual for more information about your equipment’s video output require-
ments.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via
a scan converter.
1ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting to a Network
The NP3150/NP2150/NP1150 comes standard with a LAN port (RJ-45) which provides a LAN connection using a
LAN cable. The USB Wireless LAN Unit also provides a wireless LAN connection. To use a LAN connection, you are
required to assign an IP address to the projector. For setting the NETWORK, see page 99. (From the menu, select
[SETUP]
[INSTALLATION]
[NETWORK SETTINGS])
→
→
NOTE: Some projectors may not have the USB Wireless LAN Unit. If you own a projector without the USB Wireless LAN Unit in-
stalled and need to present to the projector via a wireless connection, the optional USB Wireless LAN Unit must be installed.
With the LAN connection, two features are available: Projector control and Picture transmission.
projector control feature
With the wired or wireless LAN connection, you can control (power on/off, input select, etc.) and receive information
from the projector over the network using a computer. The following three methods are available:
* Using the HTTP Server feature on the projector. ( page 52)
→
* Using PC Control Utility 3.0 from the supplied User Supportware 5 CD-ROM.
* Using Image Express Utility 2.0 from the supplied User Supportware 5 CD-ROM.
picture transmission feature (Using WindowsVista)
A Windows Vista-based computer can be operated using the projector over a network. The projector supports the
Network Projector function and the Remote Desktop function of Windows Vista. ( page 55, 59)
→
picture transmission feature (Using User Supportware 5 CD-ROm)
With the wired or wireless LAN connection, you can send images and slides from a personal computer to the pro-
jector which then can be projected on the screen. The following two methods are available:
* Using Image Express Utility 2.0 from the supplied User Supportware 5 CD-ROM.
* Using Ulead Photo Explorer 8.0 from the supplied User Supportware 5 CD-ROM.
With the USB mouse connected to the projector, you can also operate the desktop screen on your Windows PC
connected to the LAN or the wireless LAN.
* Using Desktop Control Utility 1.0 from the supplied User Supportware 5 CD-ROM.
TIP: Five Windows software programs (Image Express Utility 2.0, Desktop Control Utility 1.0, Ulead Photo Explorer 8.0, Viewer
PPT Converter and PC Control Utility 3.0) and a Macintosh software program (Image Express Utility 2 for Mac OS X) are con-
tained on the supplied Projector User Supportware 5 CD-ROM. For their functions and operations, see the user’s guides (PDF)
contained on the same CD-ROM.
•
•
For the procedure to connect the projector with the network (wireless LAN/wired LAN), refer to “Network Set-
up Guide” attached.
For the procedure to connect Windows Vista with the network (wireless LAN/wired LAN), refer to the manual
of Windows Vista.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Example of LAN connection
(A) Example of wired LAN connection
server
hub
lan cable (not supplied)
LAN
USB(LAN)
(B) Example of wireless LAN connection
(Network Type
Infrastructure)
→
PC with wireless
lan card inserted
PC with built-in wireless
lan function
UsB Wireless lan Unit
Wireless access point
Wired lan
To make connection with a wired LAN or wireless LAN via a wireless access point, you need to select the Infra-
structure mode.
From the menu, select [SETUP]
[INSTALLATION]
[NETWORK SETTINGS]
[WIRELESS]
[ADVANCED]
→
→
→
→
[CONNECTION]
[NETWORK TYPE]
[INFRASTRUCTURE].
→
→
→
19
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
(C) Example of wireless LAN connection (Network Type
Ad Hoc)
→
UsB Wireless lan Unit
PC with wireless
PC with built-in wireless
lan card inserted
lan function
To enable direct communication (i.e., peer-to-peer) between personal computers and projectors, you need to
select the Ad Hoc mode.
From the menu, select [SETUP]
[INSTALLATION]
[NETWORK SETTINGS]
[WIRELESS]
[ADVANCED]
→
→
→
→
[CONNECTION]
[NETWORK TYPE]
[AD HOC].
→
→
→
The Ad Hoc mode complies with IEEE802.11 standard.
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cable’s three-pin plug to the AC IN of the projector, and then connect the other
plug of the supplied power cable in the wall outlet.
LEF
L
T
L
L
EN
E
F
E
N
T
S
S
S
S
H
HIF
T
I
F
T
R
I
G
H
T
D
O
W
N
U
P
S
E
L
E
C
T
3
D
RE
FORM
A
UT
O
AD
SOU
RCE
O
N
/
S
T
A
N
USB
P
D
B
LAM
STATUS
POWER
Y
WRILES
S
WRILES
to wall outlet
Make sure that the prongs are fully
inserted into both the aC in and the
wall outlet.
About Direct power Off
The projector has a feature called “Direct Power Off”. This feature allows the projector to be turned off (even when
projecting an image) using a power strip equipped with a switch and a breaker.
NOTE: Before using Direct Power Off, be sure to allow at least 20 minutes immediately after turning on the projector and starting
to display an image.
CAUTION:
Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become heated
white the projector is turned on and immediately after the projector is turned off.
CAUTION:
Do not unplug the power cable from the wall outlet or projector when the project is powered on. Doing so can
cause damage to the AC IN connector of the projector and (or) the prong plug of the power cable.
TIP: To turn off the AC power supply when the projector is powered on, use a power strip equipped with a switch and a breaker.
TIP: The projector can be unplugged during its cool down period after it is turned off.
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.
Turning on the Projector
NOTE:
• The projector has two power switches: a main power switch and a POWER (ON/STAND BY) button (POWER ON and OFF on the
remote control).
• When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off () po-
sition. Failure to do so may cause damage to the projector.
• The projector has a feature to prevent itself from being used by unauthorized individuals. To use this feature, register a key-
word. (→ page 44)
1. Remove the lens cap.
L
L
L
L
E
E
E
E
N
F
F
N
T
T
S
S
S
S
H
H
IF
I
F
T
T
R
R
IG
I
G
H
H
T
T
DD
O
W
N
U
U
•
Do not try to remove the lens cap by pulling on the
string. Doing so can cause damage.
P
P
S
E
L
E
C
T
3D
R
EF
O
R
M
A
U
T
O
A
USB
D
J
U
S
T
S
O
U
R
C
E
O
N
/S
T
A
N
U
SB
D
B
L
A
Y
M
S
P
T
A
P
T
U
O
S
W
E
R
W
I
R
E
LAMP
L
E
S
S
S
S
E
L
E
R
I
W
2. To turn on the main power to the projector, press the
Main Power switch to the on position ( I ).
STATUS
POWER
•
The projector will go into standby mode. When in stand-
by mode, the POWER indicator will light orange and the
STATUS indicator will light green.
3. After making sure that the projector is in standby
mode, press the POWER (ON/STAND BY) or POWER
(ON) button for a minimum of 2 seconds when the
STATUS indicator goes off and the POWER indicator
starts blinking.
POWER
POWER
ON
OFF
COMPUTER
1
2
VIER
VIDEO
COMPONENT
3
S-VIDEO
N
USB
LAMP
STATUS
POWER
3D.REFORM AUTO.ADJUST SOURCE
ON/SND.By
SELECT
When the POWER indicator turns a steady green,
and the projector is ready to use.
•
After you turn on your projector, ensure that the comput-
er or video source is turned on and that your lens cap is
removed.
Standby
Blinking
Power On
LAMP
LAMP
LAMP
STATUS
POWER
STATUS
POWER
STATUS
POWER
ON/SND BY
Steady green /
orange light
Blinking green Steady green
light light
Press this button for a
minimum of 2 seconds.
(
→
page 125)
NOTE: When no signal is available, a blue, black or logo screen is displayed.
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select
one of the 21 menu languages.
To select a menu language, follow these steps:
1. Use the SELECT button to select one of the 21 lan-
guages for the menu.
POWER
POWER
ON
OFF
COMPUTER
1
2
VIEWER
VIDEO
COMPONENT
3
S-VIDEO
NETWORK
SELECT
3D REFORM AUTO ADJUST SOURCE
SELECT
POWER
POWER
ON
OFF
COMPUTER
1
2
VIEWER
VIDEO
2. Press the ENTER button to execute the selection.
COMPONENT
3
S-VIDEO
NETWORK
SELECT
After this has been done, you can proceed to the menu
operation.
SELECT
3D REFORM AUTO ADJUST SOURCE
If you want, you can select the menu language later. (
[LANGUAGE] on page 90)
→
NOTE:
• The projector cannot be turned off for 60 seconds after the lamp is turned on and while the POWER indicator is blinking green.
• If you turn on the projector immediately after the lamp is turned off or when the ambient temperature is high, the cooling fans
will run for a moment and then you will get an image on the screen.
• Immediately after turning on the projector, screen flicker may occur. This is normal. Wait 3 to 5 minutes until the lamp lighting
is stabilized.
•
•
When the Lamp mode is set to Eco, the Lamp indicator will light green.
If one of the following things happens, the projector will not turn on.
-
If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this
condition the projector will not turn on to protect the internal system. If this happens, wait for the projector’s
internal components to cool down.
-
-
When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.
(
page 118)
→
If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute
and then turn on the power.
ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Selecting a Source
Selecting the computer or video source
Selecting from Source List
Press and quickly release the SOURCE button on the projector cabinet to dis-
play the Source list. Each time the SOURCE button is pressed, the input source
will change as follows: “COMPUTER 1/2/3”, “COMPONENT”, “VIDEO” (VCR or
laser disc player), “S-VIDEO”, “VIEWER” (slides on a USB memory) or “NET-
WORK” (LAN port [RJ-45] or installed USB wireless LAN unit).
SELECT
USB
LAMP
STATUS
POWER
3D REFORM AUTO ADJUST SOUE
ON/STAND BY
To display the selected source, press the ENTER button.
Detecting the Signal Automatically
Press and hold the SOURCE button for a minimum of 1 second, the projector
will search for the next available input source. Each time you press and hold the
SOURCE button for a minimum of 1 second, the input source will change as fol-
lows:
SELECT
USB
LAMP
STATUS
POWER
3D REFORM AUTO ADJUST SOUE
ON/STAND BY
COMPUTER1
COMPUTER2
COMPUTER3
COMPONENT
VIDEO
→
→
→
→
S-VIDEO VIEWER
COMPUTER1
...
→
→
→
→
If no input signal is present, the input will be skipped. When the input source
you wish to project is displayed, release the button.
POWER
POWER
ON
Using the Remote Control
Press any one of the COMPUTER 1/2/3, COMPONENT, VIDEO, S-VIDEO,
VIEWER or NETWORK buttons.
OFF
COMPUTER
1
2
VIEWER
VIDEO
COMPONT
3
S-VIDEO
NETWORK
SELECT
ꢀ4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Adjusting the Picture Size and Position
Use the lens shift dials, the adjustable tilt foot levers, the zoom lever or the focus ring to adjust the picture size and
position.
Adjusting the position of a projected image
[Lens shift]
Adjusting the focus
[Focus ring]
LE
FT
LE
NS
SH
IFT
LE
FT
LE
NS
SH
IFT
R
IG
HT
RI
GH
T
DO
WN
DO
WN
UP
UP
LE
CT
SE
LE
CT
3D
RE
FO
R
3D
RE
A
TO
FO
RM
A
DJ
AU
S
TO
AD
S
OU
JU
S
RC
E
SO
UR
O
N/S
CE
TA
ND
US
B
ON
B
Y
L
AM
P
/S
TA
S
TAT
US
ND
US
BY
LA
ST
AT
US
B
POW
ER
MP
PO
W
WIRLES
ER
WIRLES
S
S
S
WRILES
WIRLES
Adjusting the throw angle (the height of an image)
[Tilt foot] *1
Finely adjusting the size of an image
[Zoom lever]
LE
FT
LE
NS
LE
FT
LE
NS
SH
IFT
SH
IFT
RI
GH
RI
GH
T
T
DO
DO
WN
WN
UP
UP
SE
LE
CT
SE
LE
CT
3D
3D
RE
RE
FO
FO
RM
RM
AU
AU
TO
TO
AD
AD
JU
JU
ST
SO
SO
UR
UR
CE
CE
ON
ON
/S
/S
TA
TA
ND
D
US
US
LA
B
MP
BY
LA
ST
AT
US
B
BY
MP
ST
AT
U
S
PO
PO
W
W
ER
ER
W
WIRLES
S
S
S
WIRLES
Adjusting the left and right tilt of an image
[Tilt foot]
Adjusting the keystone correction
[Keystone] *2
LE
FT
LE
NS
LE
FT
LE
NS
SH
IFT
SH
IF
T
RI
GH
RI
G
T
HT
DO
DO
W
WN
N
UP
UP
SE
LE
CT
SE
LE
CT
3D
3D
RE
R
EFO
FO
RM
R
M
AU
TO
O
AD
AD
JU
JU
S
ST
SO
SO
U
RCE
UR
CE
ON
O
N/S
/S
TA
TA
N
D
US
US
LA
B
ST
AT
U
S
B
D
BY
LA
ST
AT
US
BY
MP
M
P
PO
PO
W
W
ER
ER
S
WIRLES
S
W
WIRLES
NOTE*1: Adjust the throw angle (the height of an image) when the image position is higher than the lens shift adjustable range.
NOTE*2: See “ Correcting Keystone Distortion” on page 29 for Keystone.
* In the above drawings, cables are omitted for clarity.
ꢀ5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Adjusting the position of a projected image
•
Rotate the lens shift dial.
LENS SHIFT
LEFT
RIGHT
DOWN
UP
LE
LE
NS
FT
SH
IF
T
RI
G
HT
DO
W
N
UP
SE
LE
CT
3D
R
EF
O
R
M
AU
TO
AD
JU
ST
SO
U
R
CE
O
N
/S
T
A
N
US
B
D
B
LA
M
Y
ST
P
A
T
US
PO
W
ER
W
I
E
L
E
S
S
S
S
E
L
E
R
W
NOTE: The lens shift dial for LEFT-RIGHT cannot be rotated one-half turn or more.
Do not over rotate it or it may break.
NOTE: Shifting the lens to the maximum in two directions combined will cause the edges of the image to become dark or will
cause some shadows.
TIP: The lens shift dial for UP-DOWN can be rotated one turn or more, but not beyond the adjustable range defined below.
Desktop front projection
0.5V
Vertical shift
Max. 0.5V
1V
Height of projected image
0.1H
1H
0.1H
Nomal projection position
Width of projected image
Ceiling front projection
Shift to left
Shift to right
Max.
0.5V
Vertical shift
1V
ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Adjusting the focus (Focus ring)
•
Rotate the focus ring to make focus adjustment.
Focus ring
LENS RELEASE
LE
LE
NS
FT
SH
IF
T
RI
G
HT
DO
W
N
UP
SE
LE
CT
3D
R
EF
O
R
M
AU
TO
AD
JU
ST
SO
U
R
CE
O
N
/S
TA
US
B
B
LA
M
Y
ST
P
AT
PO
US
W
ER
W
I
E
L
E
S
S
S
S
E
L
E
R
W
Finely adjusting the size of an image (Zoom lever)
•
Rotate the zoom lever to adjust the image size on the screen.
Zoom lever
LENS RELEASE
LE
LE
NS
FT
SH
IF
T
RI
G
HT
DO
W
N
UP
SE
LE
CT
3D
R
EF
O
R
M
AU
TO
AD
JU
ST
SO
U
R
C
O
N
/S
TA
N
US
B
D
B
LA
M
Y
ST
P
AT
PO
US
W
ER
W
I
E
L
E
S
S
S
S
E
L
E
R
W
ꢀꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Adjusting the Tilt Foot
1. Lift the front edge of the projector.
R
E
S
W
U
O
P
T
A
P
T
S
M
A
B
L
S
Y
B
U
D
N
A
T
S /
N
O
CAUTION:
E
C
R
U
O
S
T
S
U
J
D
A
O
T
U
A
M
R
O
F
E
R
D
3
Do not try to touch the ventilation outlet during Tilt Foot adjustment
as it can become heated while the projector is turned on and during
its cool down period after it is turned off.
T
C
E
L
E
P
S
U
1
N
W
O
D
T
H
G
I
R
S
T
F
I
H
S
N
T
F
E
L
E
L
2
2. Push up the Adjustable Tilt Foot Levers on the right and left sides
of the projector to extend the adjustable tilt feet (maximum height).
adjustable tilt
foot lever
2
3. Lower the front of the projector to the desired height.
adjustable tilt foot
adjustable tilt
foot lever
4. Release the Adjustable Tilt Foot lever to lock the Adjustable tilt foot.
there is approximately 10 degrees (up) of adjustment for the front of
the projector.
R
E
S
U
W
T
O
P
A
P
T
S
M
A
B
L
S
y
B
U
.
D
N
A
T
S /
N
O
E
C
R
U
O
S
T
S
U
J
D
A
.
O
T
U
A
M
R
O
F
E
R
.
D
3
TIP: For operating the [KEYSTONE] screen, see “ Correcting Keystone Dis-
T
C
E
L
P
E
S
U
N
W
O
D
tortion” on page 29.
ꢁ
T
H
G
I
R
S
T
F
I
H
S
N
T
F
E
L
E
L
4
NOTE: Your “Keystone” correction data can be reset by pressing and holding
the 3D REFORM button for a minimum of 2 seconds.
CAUTION:
Do not use the tilt-foot for purposes other than originally intended.
Misuses such as using the tilt foot to carry or hang (from the wall or
ceiling) the projector can cause damage to the projector.
4
ꢀ8
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Correcting Keystone Distortion
When the projector is not exactly perpendicular to the screen, keystone distortion occurs. To overcome it, you can use the
“Keystone” function, a digital technology that can adjust for keystone-type distortion, resulting in a crisp, square image.
The following procedure explains how to use the [KEYSTONE] screen from the menu to correct trapezoidal distortions.
When the projector is placed diagonally to the screen,
When the projector is set up at an angle in relation to the screen, adjust the Horizontal option of the Keystone menu
so that the top and bottom of sides of the projected image are parallel.
1. Press the 3D REFORM button on the remote control or the projec-
tor cabinet.
the Keystone screen will be displayed on the screen.
Projected area
screen frame
2. Press the SELECT button to select [VERTICAL] and then use the
SELECT or so that the left and right sides of the projected im-
age are parallel.
* adjust the vertical keystone distortion.
3. Align the left (or right) side of the screen with the left (or right) side
of the projected image.
•
•
Use the shorter side of the projected image as the base.
in the right example, use the left side as the base.
align left side
4. Press the SELECT button to select [HORIzONTAL] and then use
the SELECT
or
so that the top and bottom sides of the pro-
jected image are parallel.
•
adjust the horizontal keystone distortion.
ꢀ9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
5. Repeat steps 2 and 4 to correct keystone distortion.
6. After completing Keystone correction, press the EXIT button.
the Keystone screen will disappear.
• to perform Keystone correction again, press the 3d refOrM button
to display the Keystone screen and repeat above steps 1 to 6.
NOTE:
• If the projection angle is the same as in the last use, the previous correction setting values are retained in the memory.
• When doing Step 2, adjust the position of image so that the screen is smaller than the area of the projected area.
• To reset the 3D Reform correction setting values, press and hold the 3D REFORM button for a minimum of 2 seconds.
• Each time the 3D REFORM button is pressed, the item will change as follows: KEYSTONE → CORNERSTONE → None → KEY-
STONE → ...
For information on [CORNERSTONE], see “Correcting Horizontal and Vertical Keystone Distortion (Cornerstone)” on page 39.
• The Cornerstone adjustment will not be available during the Keystone adjustment. To perform the Cornerstone adjustment,
press and hold the 3D REFORM button for a minimum of 2 seconds to reset the Keystone correction setting values. The Key-
stone adjustment will not be available during the Cornerstone adjustment. To perform the Keystone adjustment, press and hold
the 3D REFORM button for a minimum of 2 seconds to reset the Cornerstone correction setting values.
• The 3D Reform feature can cause an image to be slightly blurred because the correction is made electronically.
ꢁ0
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Optimizing an RGB Image Automatically
Adjusting the Image Using Auto Adjust
Optimizing an RGB image automatically.
Press the AUTO ADJUST button to optimize an RGB image automatically.
This adjustment may be necessary when you connect your computer for the first time.
[Poor picture]
LASER
L-CLICK
PIP
R-CLICK
MOUSE
FREEZE
ASPECT LAMP MODE AUTO ADJ.
SELECT
VOLUME MAGNIFY
PA
U
3D REFORM AUTO AUST SOURCE
[normal picture]
PICTURE
PIC-MUTE
3D REFORM
HELP
NOTE:
• Some signals may take time to display or may not be displayed correctly.
• The Auto Adjust function does not work for component, video signals.
• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock and Phase manually. (→ page 81)
Adjusting Volume Up & Down
SELECT
Sound level from the speaker and the AUDIO OUT
jack (Stereo mini) on the projector can be adjusted.
USB
LAMP
STATUS
POWER
3D REFORM AUTO ADJUST SOURCE
ON/STAND BY
Another way to adjust volume is to use the menu.
Select [ADJUST]
the menu.
[SOUND]
[VOLUME] from
→
→
NOTE:
• Volume control is not available with the SELECT
or button when an image is enlarged by using the
MAGNIFY (+) button or when the menu is displayed.
LASER
L-CLICK
R-CLICK
MOUSE
FREEZE
PIP
ASPECT LAMP MODE AUTO ADJ.
increase volume
VOLUME MAGNIFY
PAGE
UP
DOWN
PICTURE
P
3D REFORM
decrease volume
HELP
ꢁ1
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Using the Laser Pointer
You can use the laser to draw your audience’s attention to a red dot that you can place on any object.
CAUTION:
• Do not look into the laser pointer while it is on.
• Do not point the laser beam at a person.
• Do not allow children to use the laser pointer.
Press and hold the LASER button to activate the laser pointer.
LE
FT
LE
NS
SH
IFT
RIG
HT
DO
WN
UP
SE
LE
CT
3D
.RE
FO
RM
AU
TO
.AD
J
SO
UR
CE
ON
/ST
AN
D.B
U
SB
y
LA
MP
AT
ST
WE US
R
PO
W
I
E
L
E
S
S
S
S
E
L
E
R
W
LA
SE
R
L
A
S
E
R
Setting the function switch
There are two switches on the bottom of the battery case: an applicable projector selector switch (1) and laser en-
able/disable switch (2). Check the projector being used and decide whether to enable or disable laser, then set
these switches as necessary using the tip of a thin ball-point pen. On this model, an applicable projector selector
switch (1) is not used.
OFF
ON
Switch (2)
ON.......................... Enabled.(the.laser.lights.when.the.LASER.button.is.pressed).[Factory.default]
OFF......................... Disabled.(the.laser.does.not.light.even.when.the.LASER.button.is.pressed)
Disable the laser when using in an environment in which the unit is accessible to children.
ꢁꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Turning off the Projector
To turn off the projector:
POWER
POWER
1. Press the POWER (ON/STAND BY) button on the projector
cabinet or the POWER OFF button on the remote control.
The [POWER OFF / AREYOU SURE?] message will appear.
ON
OFF
COMPUTER
1
2
VIEWER
VIO
PONENT
3
NETWORK
USB
LAMP
STATUS
POWER
SELECT
3D.REFORM AUTO.ADJUST SOURCE
ON/SND.By
2. Press the ENTER button
POWER
POWER
ON
OFF
After the projector turns off, the cooling fans keep operating for
a while (Cooling-off time).
COMPUTER
1
2
VIEWER
VIDEO
COMPONENT
3
S-VIDEO
NETWORK
The cooling fans stop operating when the projector turns off
and goes into standby mode.
When in standby mode, the POWER indicator will light orange
and the STATUS indicator will light green.
USB
LAMP
STATUS
POWER
SELECT
3D.REFORM AUTO.ADJUST SOURCE
ON/SND.By
3. After making sure that the projector is in standby mode, turn
off the Main Power switch.The power indicator will go out.
About Direct power Off
The projector has a feature called “Direct Power Off”. This fea-
ture allows the projector to be turned off (even when projecting
an image) using a power strip equipped with a switch and a
breaker.
L
E
L
L
E
E
E
F
N
N
S
F
T
T
S
S
H
S
H
I
IFFT
T
R
RI
IG
G
H
HT
T
D
D
O
O
W
W
N
N
U
U
P
P
S
E
L
E
C
T
3D
R
E
F
O
R
M
A
U
T
O
A
D
J
U
S
T
S
O
U
R
C
E
O
N
/S
T
A
N
U
SB
D
B
L
A
Y
M
S
P
T
A
P
T
U
O
S
W
E
R
W
I
R
NOTE: Before using Direct Power Off, be sure to allow at least 20 min-
utes immediately after turning on the projector and starting to display
an image.
E
L
E
S
S
S
S
E
L
E
R
I
W
CAUTION
•
Do not unplug the power cable from the wall outlet or projec-
tor when the projector is powered on. Doing so can cause
damage to the AC IN connector of the projector and (or)
the prong plug of the power cable. To turn off the AC power
supply when the projector is powered on, use a power strip
equipped with a switch and a breaker.
•
Do not turn off the AC power supply within 10 seconds of
making adjustment or setting changes and closing the menu.
Doing so can cause loss of adjustments and settings and re-
turn to default.
TIP: The projector can be unplugged during its cool down period after it is turned off.
After Use
preparation: Make sure that the main power is turned off.
1. Unplug the power cable.
2. Disconnect any other cables.
3. Retract adjustable tilt feet if extended.
4. Cover the lens with the lens cap.
ꢁꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
PIP
FREEZE
ASPECT LAMP MODE AUTO ADJ.
Turning Off the Image and Sound
VOLUME MAGNIFY
PAGE
UP
Press the PIC-MUTE button to turn off the image and sound for a short period of
time. Press again to restore the image and sound.
DOWN
PICTURE
PIC-MUTE
3D REFORM
HELP
NOTE: Even though the image is turned off, the menu still remains on the screen.
L-CLICK
MOUSE
R-CLICK
PIP
FREEZE
Freezing a Picture
ASPECT LAMODE AUTO ADJ.
VOLUME
PAGE
P
Press the FREEZE button to freeze a picture. Press again to resume motion.
DOWN
NOTE: The image is frozen but the original video is still playing back.
PICTURE
PIC-MUTE
3D REFORM
HELP
Enlarging and Moving a Picture
You can enlarge the area you want up to 400 percent.
To do so:
PIP
FREEZE
1. Press the MAGNIFY (+) button.
ASPECT LAMP MODE AUTO ADJ.
VOLUME MAGNIFY
PAGE
UP
each time the MagnifY (+) button is pressed,
DOWN
the image is magnified.
PICTURE
PIC-MUTE
RM
ELP
* image can be magnified up to 400%
POWER
POWER
ON
2. Press the SELECT
button.
OFF
COMPUTER
1
2
VIEWER
NETWORK
VIDEO
the area of the magnified image will be moved
COMPONENT
3
S-VIDEO
3. Press the MAGNIFY (-) button.
SELECT
each time the MagnifY (-) button is pressed,
the image is reduced.
PIP
FREEZE
ASPECT LAMP MODE AUTO ADJ.
VOLUME MAGNIFY
PAGE
UP
DOWN
PICTURE
PIC-MUTE
3D REFORM
ꢁ4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Changing Lamp Mode
The lamp life can be extended by using the Eco mode.
T
T
I
E
X
R
E
LASER
To change to the [ECO] mode, do the following:
L-CLICK
PIP
R-CLICK
MOUSE
FREEZE
1. Press the LAMP MODE button to display [LAMP MODE] screen.
ASPECT LAMP MODE AUTO ADJ.
2. Use the SELECT or button to select [ECO] mode.
VOLUME MAGFY
PAGE
UP
3. Press the ENTER button.
N
PICTURE
PIC-MUTE
REFORM
HELP
To cancel it, press the EXIT button.
to change from [eCO] to [nOrMal], go back to step 2 and select [nOrMal]. re-
peat step 3.
Lamp Mode
Description
Status of LAMP indicator
Off
NORMAL
MODE
This is the Default setting
(100% Brightness).
ECO MODE
Select this mode to increase the lamp
life (approx. 80% Brightness (light output)
on NP3150 and approx. 88% Brightness
(light output) on NP2150/NP1150)
Steady Green light
NOTE:
• The projector is always in [NORMAL MODE] for one minute after the lamp is turned on and while the POWER indicator is blink-
ing green. The lamp condition will not be affected even when [LAMP MODE] is changed.
• After a lapse of one minute from when the projector displays a blue, black or logo screen, [LAMP MODE] will automatically
switch to [ECO MODE].
The projector will return to the [NORMAL MODE] once a signal is accepted.
T
T
I
POWER
POWER
OFF
ON
Getting Integrated Help
LASER
COMPUTER
1
2
VIEWER
VIDEO
L-CLICK
PIP
R-CLICK
MOUSE
FREEZE
COMPONENT
You get the contents about Help in English, German
and Japanese.
3
S-VIDEO
NETWORK
ASPECT LAMP MODE AUTO ADJ.
VOLUME MAGNIFY
PAGE
UP
SELECT
1. Press the HELP button on the remote control.
DOWN
PICTURE
PIC-MUTE
3D REFORM
HELP
• When no menus appear, the “How to Use Help”
screen will be displayed.
•
When menus appear, the screen will be displayed,
explaining the function of a highlighted item.
display help
exit help
2. Use the SELECT or button to scroll the view-
ing area.
3. Press the EXIT button.
• The Help will be closed.
ꢁ5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Using a USB Mouse
USB
Using a USB mouse gives you a smooth operation. A commercially
available USB mouse can be used.
USB(LAN)
Menu items that can be operated with your USB mouse are:
•
•
•
•
•
•
•
VIEWER
NETWORK
ENTRY LIST
TOOLS
SECURITY SETTINGS
NETWORK SETTINGS
CORNERSTONE
NOTE: We do not warrant that the USB port of the projector will support all USB mouse devices in the market.
NOTE: Do not try to insert the plug of your USB mouse into the LAN port (LAN) of the projector.
Doing so can cause damage to the LAN port.
Operate the Menus using the USB mouse
Mouse Cursor
When connecting a USB mouse to the projector, you get a mouse cursor on the screen.
Unless you use your USB mouse within 10 seconds, the mouse cursor disappears.
Adjusting and Setting Display
You can select a menu item and click with the left mouse button to make adjustments and settings.
With the middle button you can use a scroll bar in the menu or the help.
Icons on the top right of the menu
•
•
•
•
•
Click [Clock] symbol to display the [DATE, TIME PRESET] menu.
Click [Network] symbol to display the [NETWORK SETTINGS] menu. ( page 99)
→
Click [Mouse] symbol to display the [MOUSE] menu.
Click [?] to display a selection of the selected menu item.
Click
to close the menu.
ꢁꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Using the Optional Remote Mouse Receiver (NP01MR)
The optional remote mouse receiver enables you to operate your computer’s mouse functions from the remote con-
trol. It is a great convenience for your computer-generated presentations.
Connecting the remote mouse receiver to your computer
If you wish to use the remote mouse function, connect the mouse receiver and computer.
The mouse receiver can be connected directly to the computer’s USB port (type A).
NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change
your computer settings.
Computer
remote mouse receiver
to UsB port of PC or Macintosh
When operating a computer via the remote mouse receiver
7m/22 feet
30
30
remote sensor on the remote mouse receiver
When connecting using the USB port
For PC, the mouse receiver can only be used with a Windows 98/Me/XP*, Windows 2000, Windows Vista, or
Mac OS X 10.0.0 or later operating system.
* NOTE: In SP1 or older version of Windows XP, if the mouse cursor will not move correctly, do the following:
Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer
Options tab].
NOTE: Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa. The computer may
not identify the mouse receiver if it is repeatedly connected and disconnected in rapid intervals.
ꢁꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Operating your computer’s mouse from the remote control
You can operate your computer’s mouse from the remote control.
PAGE.UP/DOWN.Button....................scrolls.the.viewing.area.of.the.window.or.to.move.to.the.previous.or.next.slide.in.Power-
Point.on.your.computer.
SELECT..Button...................moves.the.mouse.cursor.on.your.computer.
MOUSE.L-CLICK.Button...................works.as.the.mouse.left.button.
MOUSE.R-CLICK.Button...................works.as.the.mouse.right.button.
NOTE: When you operate the computer using the SELECT button with the menu displayed, both the menu and the
mouse pointer will be affected. Close the menu and perform the mouse operation.
About Drag mode:
By pressing the MOUSE L-CLICK or R-CLICK button for 2 or 3 seconds then releasing, the drag mode is set and
the drag operation can be performed simply by pressing the SELECT
MOUSE L-CLICK (or R-CLICK) button. To cancel it, press the MOUSE R-CLICK (or L-CLICK) button.
button. To drop the item, press the
TIP: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the user
documentation or online help supplied with your computer.
ꢁ8
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Correcting Horizontal and Vertical Keystone Distortion (Cor-
nerstone)
Use the 3D Reform feature to correct keystone (trapezoidal) distortion to make the top or bottom and the left or right
side of the screen longer or shorter so that the projected image is rectangular.
Cornerstone
1. Press and hold the 3D REFORM button for a minimum of 2 seconds to reset current adjustments.
Current adjustments for [KeYstOne] or [COrnerstOne] will be cleared.
2. Project an image so that the screen is smaller than the area of the raster.
3. Pick up any one of the corners and align the corner of the image with a corner of the screen.
Projected image
the drawing shows the up-
per right corner.
screen
4. Press the 3D REFORM button twice.
the Cornerstone adjustment screen is displayed.
the drawing shows the upper left
icon ( ) is selected.
TIP: If you are adjusting [KEYSTONE], [CORNERSTONE] will not be
available. If this happens, press and hold the 3D REFORM button for a
minimum of 2 seconds to reset the [KEYSTONE] adjustments.
5. Use the SELECT
button to select one icon ( ) which points in the direction you wish to move the
projected image frame.
6. Press the ENTER button.
ꢁ9
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
7. Use the SELECT
button to move the projected image frame as shown on the example.
screen
8. Press the ENTER button.
screen
9. Use the SELECT
button to select another icon which points in the direction.
On the Cornerstone adjustment screen, select [eXit] or press the eXit button on the remote control.
screen
the confirmation screen is displayed.
10.Press the SELECT or button to highlight the [OK] and press the ENTER button.
This completes the Cornerstone correction.
Selecting [CANCEL] will return to the adjustment screen without saving changes (Step 3).
Selecting [RESET] will return to the factory default.
Selecting [UNDO] will exit without saving changes.
NOTE: To reset the 3D Reform correction setting values, press and hold the 3D REFORM button for a minimum of 2 seconds.
NOTE: During 3D Reform adjustment, [ASPECT RATIO] and [SCREEN] may not be available. Should this happen, first reset the
3D Reform data and then do each setting. Second repeat the 3D Reform adjustment. Changing [ASPECT RATIO] and/or [SCREEN]
setting can limit [3D REFORM] in its adjustable range.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
The adjustable ranges for ꢁD Reform are as follows:
HORIZONTAL
VERTICAL
CORNERSTONE
KEYSTONE
Max. +/– 40° approx.
Max. +/– 30° approx.
* The following are conditions under which the maximum angle is achieved:
•
•
When the standard lens is used
When the lens shift is set to the center
When the lens shift is used and yet the image is not displayed in the center of the screen, the adjustable
range will be increased or decreased.
•
Image is projected in Wide (Zoom lever)
NOTE:
• If the Cornerstone screen is unavailable (grayed), press and hold the 3D REFORM button for a minimum of 2 seconds to reset
the current correction data. The Cornerstone function becomes available.
• Turning on the projector will reset the previous correction setting values and correct distortion anew if the projection angle is
changed from the last use.
If the projection angle is the same as in the last use, the previous correction setting values are retained in the memory.
NOTE: Using 3D Reform correction can cause the image to be slightly blurred because the correction is made electronically.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Using Picture in Picture (PIP) Function
9
The projector has a feature that allows you to view two different signals simultaneously. This feature is called as Pic-
ture in Picture (PIP).
From the menu you can select [SETUP]
[BASIC]
[PIP].
→
→
NOTE:
• The Magnify and [SCREEN] setting are not available in PIP mode.
• Adjusting for picture and sound is available for the main picture only.
• To turn on PIP mode while in Picture Mute or Freeze, Picture Mute and Freeze will be applied simultaneously to both the main
and sub pictures.
• The main picture signal supports the COMPUTER 1 and 2 inputs.
The sub picture signal supports the VIDEO input only.
PIP POSITION
This option allows you to select the position of a sub picture in the main picture.
Use the SELECT or button to select the sub picture’s position and press the ENTER button.
The options are: top-left, top-right, bottom-left, and bottom-right.
NOTE:
• The default setting is [BOTTOM-RIGHT].
4ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Viewing a sub picture in the main picture
You can use the PIP button on the remote control to view a sub picture in the main picture.
To do so, follow the steps.
1. Press the PIP button on the remote control.
the sub picture will be displayed in the main picture.
sub picture
2. Press the PIP button again to display the main picture only.
NOTE: The main picture’s sound will be output.
4ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Preventing Unauthorized Use of the Projector
Assigning a keyword prevents the projector from being used by unauthorized individuals.
Assigning a Keyword for the first time
1. Press the MENU button.
The menu will be displayed.
2. Press the SELECT button to highlight the [SETUP] submenu and press the ENTER button.
The page tab [BASIC] will be highlighted.
3. Press the SELECT button twice to highlight the page tab [INSTALLATION].
44
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
4. Press the SELECT button three times to highlight [SECURITY SETTINGS].
5. Press the ENTER button to display the SECURITY SETTINGS menu.
6. Press the SELECT button four times to highlight [SECURITY-SETTINGS] and press the ENTER button.
The Security screen will be displayed.
7.Press the SELECT button once to highlight the Keyword entry box and press the ENTER button.
The Software keyboard will be displayed.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
8. Enter an alphanumeric keyword using the Software keyboard.
For example, to enter “1234”, follow the steps 8-1 to 8-4 below.
NOTE:
• When using your USB mouse, click each number or alphabet.
BS: Delete the character before the cursor or highlight.
: Confirm the keyword and close the Software keyboard.
• The keyword must be 1 to 10 characters long.
• Please make a note of your keyword.
• Do not use spaces (SP) in your keyword.
enter a keyword by using the remote control.
8-1. Press the MenU button and the aUtO.adJ. button to enter “1”.
the asterisk “ ” will be displayed in the keyword entry box.
8-2. Press the MenU button and the seleCt button to enter “2”.
the asterisk “
” will be displayed in the keyword entry box.
8-3. Press the MenU button and the seleCt button to enter “3”.
the asterisk “
” will be displayed in the keyword entry box.
8-4. Press the MenU button and the seleCt button to enter “4”.
the asterisk “
” will be displayed in the keyword entry box.
8-5. Press the enter button.
9. Press the SELECT button once to highlight [OFF] and press the SELECT button to highlight [ON].
4ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
10.Press the SELECT button to highlight [OK] and press the ENTER button.
The confirmation screen will be displayed.
11.Press the SELECT or button to highlight [YES] and press the ENTER button.
The Security Function is now enabled.
Checking If Security is enabled
Turn off the projector and turn it back on to check if the Security function is enabled.
1. Press the POWER (ON/STANDBY) button.
the [POWer Off / are YOU sUre?] message will appear.
Press the enter button or the POWer (On/standBY) or the POWer Off button again.
the lamp lights off and the POWer indicator flashes orange. Please wait until the POWer indicator changes
from flashing to steady light.
2. When the POWER indicator lights steady orange, push the Main POWER switch to the off position (O).
the projector will turn off.
3. Push the Main POWER switch to the on position (I).
the POWer indicator lights orange. the projector is in standby condition.
4. Press and hold the POWER (ON/STANDBY) button for a minimum of two seconds.
the projector will turn on. the [PrOJeCtOr is lOCKed! enter YOUr KeYWOrd.] message will be dis-
played at the bottom of the screen.
5. Press the MENU button.
the Keyword entry screen will be displayed
6. Press the ENTER button.
the software keyboard will be displayed.
7. Use the same procedures as steps 1 to 8 described in the “Assigning a Keyword for the first time” sec-
tion to enter “1234”.
each time one number is entered, an “ ” (asterisk) will appear. Keyword appears as asterisks so the real key-
word is hidden.
8. After entering your keyword, highlight [OK] and press the ENTER button.
the software keyboard will disappear. this will allow you to operate the projector.
4ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Disabling the Security
1. Press the MENU button.
the menu will be displayed.
NOTE: Immediately after the projector has been turned on and the “Projector is locked! Enter your keyword.” message is dis-
played at the bottom of the screen, pressing the MENU button will display the Keyword entry will be displayed. At this time,
pressing the MENU button will display the menu.
2. Press the SELECT button to highlight [SETUP] and press the ENTER button.
the page tab [BasiC] will be highlighted.
3. Press the SELECT button twice to highlight the page tab [INSTALLATION].
4. Press the SELECT
ton.
button three times to highlight [SECURITY SETTINGS] and press the ENTER but-
5. Press the SELECT button four times to highlight [SECURITY] - [SETTINGS] and press the ENTER but-
ton.
the Keyword entry screen will be displayed
6. Press the ENTER button.
the software keyboard will be displayed.
7. Use the same procedures as steps 1 to 8 described in the “Assigning a Keyword for the first time” sec-
tion to enter “1234”.
each time one number is entered, an “ ” (asterisk) will appear. Keyword appears as asterisks so the real key-
word is hidden.
8. After entering your keyword, highlight [OK] and press the ENTER button.
the software keyboard will disappear. the security screen will be displayed.
9. Highlight [ON] and press the SELECT button to highlight [OFF].
10.Press the SELECT button to highlight [OK] and press the ENTER button.
the security function is now disabled.
NOTE: Do not forget your keyword. However, if you forget your keyword, NEC or your dealer will provide you with your Release
Code upon proof of ownership.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Limiting Access Level to Available Menu Items
The Account function allows you to manage available menu items by user level.
The projector has two menu modes: the ADVANCED menu and the BASIC menu.
ADVANCED.menu... This.is.the.menu.that.contains.all.the.available.menus.and.commands..Users.with.an.ADMINISTRATOR.or.
ADVANCED.account.can.access.the.ADVANCED.menu.
BASIC.menu........... This.is.the.basic.menu.that.contains.minimum.essentials.of.menus.and.commands..Users.with.a.BASIC.
account.can.access.the.BASIC.menu.
See page 50 for settings available to ADVANCED and BASIC menus.
NOTE:
• A user with an ADMINISTRATOR account that has no password set is registered at the factory.
This will allow the user to access the ACCOUNT items without password entry.
Logging On
Logging on your projector
When a user is registered, trying to display the menu will display the LOGON screen, prompting the user to select
the user and to enter the password.
NOTE: If one user logs on to the projector, any other user cannot log on.
1. Enter a user name.
2. Enter the registered user name if you have it.
3. Select [OK].
Logging Off
Logging off your projector
Logging off your projector will prevent an unauthorized user from operating your projector.
1. From the menu, select [SETUP]
2. Select [YES].
[BASIC]
[LOGOFF].
→
→
49
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Creating or Adding a User
1. From the menu, select [SETUP]
[INSTALLATION]
[SECURITY SETTINGS].
→
→
2. Select [ACCOUNT]-[SETTINGS].
the [aCCOUnt] setting screen will be displayed.
3. Select [CREATE].
the [aCCOUnt] create screen will be displayed.
4. Enter a user name, user type, and password.
•
•
•
A user name must be 16 alphanumeric characters or less (case sensitive).
User type has two options: [ADVANCED] and [BASIC].
Use the software keyboard to enter a password in the NEW PASSWORD entry field.
a password must be 10 alphanumeric characters or less. if no password is set, the user is registered without a
password.
•
After entering a password, enter the same password in [CONFIRM PASSWORD] input screen again.
5. Place a checkmark on [ENABLE].
the account will be made available.
6. Select [OK].
this will complete adding a user.
NOTE: Up to 12 user names can be created.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Editing a User (Changing Account Settings)
1. From the menu, select [SETUP]
[INSTALLATION]
[SECURITY SETTINGS].
→
→
NOTE: A user with an ADMINISTRATOR account is recommended to change the account settings.
2. Select [ACCOUNT]-[SETTINGS].
the [aCCOUnt] setting screen will be displayed.
3. Select a user name you wish to edit.
4. Select [EDIT].
the [edit] screen will be displayed.
enter your password and press the enter button.
if no password is set, simply press the enter button without entering any password.
5. Change the settings and select [OK].
Deleting a User
1. From the menu, select [SETUP]
[INSTALLATION]
[SECURITY SETTINGS].
→
→
NOTE: A user with an ADMINISTRATOR account is recommended to delete the account settings.
2. Select [ACCOUNT]-[SETTINGS].
the [aCCOUnt] setting screen will be displayed.
3. Select a user name you wish to delete.
4. Select [DELETE].
the [delete] screen will be displayed.
enter your password and press the enter button.
the confirmation screen will be displayed.
5. Select [YES].
this will complete deleting the user.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Operation Using an HTTP Browser
L
Overview
The use of HTTP server functions will allow control of the projector from a web browser without the installation of
special software. Please be sure to use “Microsoft Internet Explorer 4.x” or a higher version for the web browser. (This
device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting meth-
od will vary depending on the version of browser. Please refer to the help files and the other information provided in
your software.)
Access is gained to the HTTP server functions by specifying
http:// <the projector’s IP address> /index.html
in the entry column of the URL.
NOTE:
• The display’s or button’s response can be slowed down or operation may not be accepted depending the settings of your net-
work. Should this happen, consult your network administrator.
The projector may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a moment and
repeat. If you still can’t get any response, turn off and back on the projector.
• Do not use the HTTP Server functions and PC Control Utility 3.0 included on the supplied CD-ROM. Using both at the same time
may result in a connection failure or slow response.
Preparation Before Use
Make network connections and set up the projector and confirm that it is complete before engaging in browser op-
erations. ( [NETWORK SETTINGS] on page 99)
→
Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and
the setting method. Although the type of proxy server will be a factor, it is possible that items that have actually been
set will not be displayed depending on the effectiveness of the cache, and the contents set from the browser may
not be reflected in operation. It is recommended that a proxy server not be used unless it is unavoidable.
Handling of the Address for Operation via a Browser
Regarding the actual address that is entered for the address or entered to the URL column when operation of the
projector is via a browser, the host name can be used as it is when the host name corresponding to the IP address
of the projector has been registered to the domain name server by a network administrator, or the host name cor-
responding to the IP address of the projector has been set in the “HOSTS” file of the computer being used.
Example 1: When the host name of the projector has been set to “pj.nec.co.jp”,
http://pj.nec.co.jp/index.html
is specified for the address or the entry column of the URL.
Example 2: When the IP address of the projector is “192.168.73.1”, access is gained to the
HTTP server functions by specifying
http://192.168.73.1/index.html
for the address or the entry column of the URL.
5ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Structure of the HTTP Server
POWER: This controls the power of the projector.
ON.....................................Power is switched on.
OFF...................................Power is switched off.
VOLUME: This controls the volume of the projector.
.....................................Increases the volume adjustment value.
.....................................Decreases the volume adjustment value.
AV-MUTE: This controls the mute function of the projector.
PICTURE ON....................Mutes the video.
PICTURE OFF ..................Cancels the video muting.
SOUND ON.......................Mutes the audio.
SOUND OFF.....................Cancels the audio muting.
OSD ON............................Mutes the on-screen display.
OSD OFF ..........................Cancels the muting of the on-screen display.
ALL ON .............................Mutes each of the video, audio, and on-screen display functions.
ALL OFF............................Cancels the muting of each of the video, audio, and on-screen display functions.
PICTURE: Controls the video adjustment of the projector.
BRIGHTNESS
.............Increases the brightness adjustment value.
BRIGHTNESS ..............Decreases the brightness adjustment value.
CONTRAST
CONTRAST
.................Increases the contrast adjustment value.
.................Decreases the contrast adjustment value.
COLOR
COLOR
........................Increases the color adjustment value.
........................Decreases the color adjustment value.
HUE ..............................Increases the hue adjustment value.
HUE ..............................Decreases the hue adjustment value.
SHARPNESS
SHARPNESS
...............Increases the sharpness adjustment value.
...............Decreases the sharpness adjustment value.
•
The functions that can be controlled will vary depending on the signal being input to the projector. ( page 78)
→
5ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
SOURCE SELECT: This switches the input connector of the projector.
COMPUTER1....................Switches to the COMPUTER 1 IN connector.
COMPUTER2....................Switches to the COMPUTER 2 IN connector.
COMPUTER3....................Switches to the COMPUTER 3 (DVI-D) IN connector.
COMPONENT...................Switches to the COMPONENT IN connectors.
VIDEO...............................Switches to the VIDEO IN connector.
S-VIDEO ...........................Switches to the S-VIDEO IN connector.
VIEWER............................Switches to the data on the USB memory device.
NETWORK........................Switches to a LAN signal.
PROJECTOR STATUS: This displays the condition of the projector.
LAMP LIFE REMAINING ....Displays the remaining life of the lamp as a percentage.
LAMP HOURS USED.......Displays how many hours the lamp has been used.
FILTER HOURS USED ....Displays how many hours the filter has been used.
ERROR STATUS..............Displays the status of errors occurring within the projector.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Projecting Your Computer’s Screen Image from the Projector
M
via a Network [NETWORK PROJECTOR]
A Windows Vista-based computer can be operated using the projector over a network. The projector supports the
Network Projector function and the Remote Desktop function of Windows Vista.
By selecting the projector connected to the same network as that of your PC, the PC screen image can be project-
ed to the screen via network. There is no need of connection using the VGA signal cable.
LEF
LEN
T
S
S
HIF
T
RIG
HT
DOW
N
UP
SEL
ECT
3D
REF
ORM
AUT
O
A
DJU
ST
SO
RCE
ON
/ST
AND
LAN
US
LAM
BY
B
STA
P
POW TUS
ER
W
I
E
E
S
S
E
E
I
W
The projector supports the Network Projector function and the Remote Desktop function of Windows Vista.
Operation Environment
Applicable OS
Windows Vista (32-bit version) Home Premium
Windows Vista (32-bit version) Business
Windows Vista (32-bit version) Ultimate
Windows Vista (32-bit version) Enterprise
(Note) These functions are not available on Windows Vista Home Basic.
Hardware specifications
The specifications recommended by Microsoft as the operation environment for
Windows Vista should be satisfied.
Network Environment
Screen color
Wired LAN or wireless LAN environment that supports TCP/IP is required.
High Color (16 bits)
True Color (24 bits and 32 bits)
* Setting with 256 colors or less is not available.
Changing the resolution of Windows Vista screen to 10ꢀ4 x ꢃꢂ8
1. Click [Start] from the desktop of Windows Vista.
2. Click [Control Panel].
3. Click [Adjust screen resolution] displayed under [Appearance and Personalization].
4. Operate [Resolution] slide bar to change the resolution to [1024 by 768 pixels].
55
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
5. Click [OK].
the message “do you keep this screen setting?” is displayed.
6. Click [Yes].
the resolution of Windows Vista screen is changed to 1024 x 768.
Setting the projector to Network projector Input mode
1. With the projector turned on, press the SOURCE button.
the input selection window appears.
another way to display the input selection window is to press the netWOrK button on the remote control. the
netWOrK screen will be displayed. go to step 3.
2. Press the SELECT or button to select [NETWORK] and press the ENTER button.
in the screen, the [netWOrK] menu is displayed.
3. From the [NETWORK] menu, select [NETWORK PROJECTOR].
the [PrOJeCtOr naMe/disPlaY resOlUtiOn/PassWOrd/Url] will be displayed.
5ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
TIP:
• To change the default password “1234”, select [CHANGE] and press the ENTER button.
The [ENTER PASSWORD] screen will be displayed, Enter a numeric password. The password must be eight characters or less.
The changed password stored in the projector will be displayed in the [NETWORK PROJECTOR] screen next time.
projecting the Image with Network projector
1. Click [Start] from the desktop of Windows Vista.
2. Click [All Programs].
3. Click [Accessories].
4. Click [Connect to a Network Projector].
When the [Permission Connect to a network Projector] window appears,click [Yes.].
the “Connect to a network Projector” window appears.
5. Click [ Search for a projector (recommended)].
→
in the “available projectors” box, “nP3150 series” is displayed.
6. Click [NP3150 Series].
the message “enter the password for the projector that you selected.” is displayed at the bottom of the window.
7. Check the password displayed in the screen projected by the projector.
8. Input the password to the password input box displayed by the operation at Step 6.
5ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
9. Click [Connect].
the network projector function works and the screen of Windows Vista is projected from the projector.
NOTE: When the network projector function works, the background color of the desktop changes to black. When the network
projector function is stopped, the original background color is restored.
Reference: If the projector cannot be found at Step 5, click [ → Enter the projector address]. Then, input the “Network ad-
dress” (Input example: http://10.32.97.61/lan) and “Projectorpassword” (Input example: 82291627) displayed in the screen
projected from the projector.
Exiting the Network projector Operation
1. Click [Projecting: NP3150 Series] in the Windows Vista task bar.
2. Click [Disconnect].
the network Projector function is stopped.
3. Press the MENU button of the projector to display the menu. From the menu, select an input terminal
other than [NETWORK].
58
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Using the Projector to Operate Your Computer via a Network
N
[REMOTE DESKTOP]
•
By selecting the PC connected to the same network as that of the projector, the PC screen image can be pro-
jected to the screen via network.
Then, by operating the keyboard connected to the projector, you can operate Windows Vista on the PC con-
nected with the network.
•
With the Remote Desktop function, you can remotely operate the PC placed at a distance from the projector.
Meeting room
LEFT
LENS
SHIFT
RIGH
T
DOWN
UP
SELE
CT
3
EFOR
M
AUTO
ADJU
ST
SOUR
CE
ON/S
TAND
B
US
TAMP
B
LAN
O
US
W
R
L
S
S
L
I
Office
NOTE:
• Available versions of Windows Vista are provided on page 55.
• In this user’s manual this feature is described using Windows Vista as an example, but Windows XP will also work with this
feature.
Windows XP Home Edition Service Pack 2 or later
Windows XP Professional Service Pack 2 or later
• A USB keyboard is required to use the Remote Desktop function.
• The Remote Desktop function can be operated with a USB keyboard only. Using a USB mouse with a USB keyboard is more
useful for operating.
Use a commercially available USB keyboard and USB mouse.
Prepare a commercially available USB keyboard (US layout version).
NOTE: We do not warrant that the USB port of the projector will support all USB keyboards in the market.
Connect the USB keyboard to the USB port (Type A) of the projector. Connect a USB mouse to the USB keyboard.
L
L
E
E
F
N
T
S
S
H
H
IF
T
R
IG
T
D
O
W
N
U
P
S
E
L
E
C
T
3
D
R
E
FORM
AU
TO
ADJU
ST
S
OU
RCE
ON/ST
A
U
S
B
B
LAM
Y
S
P
T
A
T
P
U
OW
S
ER
W
I
R
E
L
E
S
S
S
S
E
L
E
R
I
W
59
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Setting the password to the user account of Windows Vista
TIP: If a password has been set for an account, the steps 1 to 9 can be skipped.
1. Click [Start] from the desktop of Windows Vista.
2. Click [Control Panel].
3. Click [Add or remove user accounts] displayed under [User Accounts].
4. When the [User Account Control] confirmation window appears, click [Continue].
5. Click [Administrator].
6. Click [Create a password].
7. Input the password to the [New password] box.
8. Input the same password as that at Step 7 to the [Confirm new password] box.
9. Click [Create a password].
the administrator is changed to [Password Protection].
Setting the Remote Access
1. Click [Start] from the desktop of Windows Vista.
2. Click [Control Panel].
3. Click [System and Maintenance].
4. Click [Allow remote access] displayed under [System].
5. When the [User Account Control] confirmation window appears, click [Continue].
the [system Properties] window appears.
6. Click [Allow connections from computers running any version of Remote Desktop (less secure)] in the
Remote Desktop box and click [OK].
Checking the Ip address on Windows Vista
1. Click [Start] from the desktop of Windows Vista.
2. Click [Control Panel].
3. Click [View network status and tasks] displayed under [Network and Internet].
ꢂ0
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
4. Click [View status] displayed in blue on the right of [Local Area Connection] in the window.
the [local area Connection status] window appears.
5. Click [Details...].
Write down the value for “iPv4 iP address” (xxx.xxx.xxx.xxx) displayed.
6. Click [Close].
7. Click [X] at the upper right of the window.
the system goes back to the desktop.
Starting the Remote Desktop
1. With the projector turned on, press the SOURCE button.
the input selection window appears.
another way to display the input selection window is to press the netWOrK button on the remote control. the
netWOrK screen will be displayed. go to step 3.
ꢂ1
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
2. Press the SELECT or button to select [NETWORK] and press the ENTER button.
the [netWOrK] menu will be displayed.
3. From the [NETWORK] menu, use the USB keyboard to select [REMOTE DESKTOP CONNECTION].
the [remote desktop Connection] window appears.
TIP:
Setting [OPTIONS] in REMOTE DESKTOP
Clicking [OPTIONS] displays the [PERFORMANCE] screen.
Making settings to [OPTIONS] will allow you to display the desktop background, or to enable the window animation function
during the Remote Desktop operation. However, doing this will cause the display’s or mouse’s response to slow down.
If the display’s or mouse’s response is slowed down, try one or more of the following:
DESKTOP BACKGROUND: Clear the check mark to display the desktop background in monochrome.
MENU AND WINDOW ANIMATION: Clear the check mark to disable menu and window animation.
THEMES: Clear the check mark not to use Themes.
SHOW CONTENTS OF WINDOW WHILE DRAGGING: Clear the check mark to show only the window pane
while dragging.
4. Operate the USB keyboard to input the IP address of Windows Vista and click [Connect].
the log-on screen of Windows Vista is displayed in the screen projected by the projector.
5. Operate the USB keyboard to input the user’s password and press [Enter].
the remote desktop function is started.
Windows Vista desktop is displayed in the screen projected by the projector.
log out the computer.
Use the UsB keyboard connected to the projector to operate Windows Vista.
NOTE: When the projection is made with the remote desktop function, the background color of the desktop is changed to
black.
ꢂꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Exiting the Remote Desktop
1. Operate the keyboard to click [Start] from the desktop screen projected by the projector.
2. Click [X] on the right of the start menu.
the remote desktop function is stopped.
3. Press the SOURCE button of the projector to select an input terminal other than [NETWORK].
When using the remote control, press a button other than the netWOrK button.
ꢂꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
Making the Most out of the Viewer Function
Features
The Viewer feature allows you to view slides stored on a USB memory on the projector. Even if no computer is
available, presentations can be conducted simply with the projector. This feature is convenient for holding presenta-
tions at meetings and in offices, as well as for playing images taken on digital cameras.
Easy to use
•
•
•
•
Presentations can be started immediately simply by inserting a USB memory (not supplied)
Easy slide switching
Remote control operation
Jumping to a list of slides or any specific slide
Simple utility software (for computer)
•
Ulead Photo Explorer 8.0SE Basic operable.
•
Control screen for displaying lists of slides and editing.
TIP:
• To use the Viewer, first you need to create presentation materials on your PC (JPEG, BMP, GIF*1, PNG*1, Index*2 files).
For creating presentation materials using the Ulead Photo Explorer 8.0, see the supplied “User Supportware 5 User’s Guide” or
On-line help in Ulead Photo Explorer 8.0.
*1Both PNG and GIF format support non-interlaced images only.
*2“Index” file is a file created using the Ulead Photo Explorer 8.0 contained on the supplied NEC User Supportware 5 CD-ROM.
See the supplied “User Supportware 5 User’s Guide” for installing the Ulead Photo Explorer 8.0 on your computer.
NOTE:
• Use commercially available USB memory devices.
• We do not warrant that the USB port of the projector will support all USB memory devices in the market.
• The projector does not support NTFS formatted USB memory device.
Be sure to use a USB memory device formatted with the FAT32, FAT16 or FAT file system.
To format your USB memory device in your computer, refer to the document or help file that comes with your Windows.
Saving data to a USB memory device
There are two ways to save your data to a USB memory device.
Using Ulead Photo Explorer 8.0
Install Ulead Photo Explorer 8.0 from the supplied User Supportware 5 CD-ROM to your computer. Use Ulead Pho-
to Explorer 8.0 to create graphic data on your computer and save the files to a USB memory device.
Files created on Ulead Photo Explorer 8.0/Viewer PPT Converter 3.0 are index format and are stored in [Presentation]
folder.
For more details about Ulead Photo Explorer 8.0, see the supplied “Wired and Wireless Network Setup Guide”, “Basic
Operation Guide (PDF)” on the User Supportware 5 CD-ROM and the help file of Ulead Photo Explorer 8.0.
Using Windows Explorer to save files
Supported file format for Viewer are JPEG, BMP, PNG, GIF and Index.
ꢂ4
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
Operating the Viewer Function from the Projector (playback)
This section describes the operation for showing slides created using the Viewer function with the projector. It is
also possible to make slides directly from the images projected with the projector.
Projecting slides (Viewer)
Preparation: Store JPEG or BMP files (JPEG, BMP, non-interlaced GIF or non-interlaced PNG files) in a USB mem-
ory inserted into your PC.
To start the Viewer, press the SOURCE button on the cabinet to select [VIEWER]. ( page 24)
→
Viewer screen will be displayed. (A slide will be displayed at the factory default.)
•
You can use the VIEWER button on the remote control to select [VIEWER].
Operating Viewer Menu
1. Insert a USB memory into the USB port of the projector.
The USB indicator lights.
2. Press the VIEWER button on the remote control or select the [VIEWER] from the source list.
An image stored in the USB memory will be displayed.
NOTE: When [SHOW THUMBNAILS] is turned on in the OPTIONS menu, the thumbnail screen will be displayed. (→ page 67)
NOTE: Pressing the EXIT button during slide playback will display the thumbnail screen.
Slide and Thumbnail
When VIEWER is selected, one of the two screens is displayed.
One is a slide and the other is a thumbnail screen.
[SLIDE]
[ThUmBNAILS]
TIP: To switch from [SLIDE] to [THUMBNAILS], press the EXIT button.
The Control Bar
Pressing the MENU button during slide playback will display the control bar which allows you to operate a slide-
show. Press the EXIT button to close the control bar.
The control bar contains the following icon buttons:
selects the currently
displayed image for your
advances to the next image. background logo.
Quits slide playback and
then returns to the thumb-
nail screen.
returns to the pre-
vious image.
rotates the image 90 degrees
counterclockwise.
Plays back slides.
rotates the image 90 degrees
clockwise.
stops auto Play while you
are playing back slides.
ꢂ5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
Thumbnail screen
list of folders
scroll bar
highlight
thumbnail/file name
Cursor (yellow)
information
number of files
Highlight....................................Indicates.the.selected.folder.or.drive.
List.of.folders.............................Indicates.folders.contained.on.a.USB.memory.
Information................................Indicates.information.of.the.selected.file.or.folder.
Folder:.folder.name,.number.of.files,.creation.date.(month/day/year),.creation.time.(hour:minute:
second).
File:.file.name,.slide.number/number.of.displayable.slides.in.a.folder,.creation.date.(month/day/
year),.creation.time.(hour:minute:second),.file.size.
Number.of.files..........................Indicates.number.of.displayable.slides.in.the.selected.folder..The.maximum.number.of.images.
recognized.as.slides.within.one.directory.is.about.250.
Thumbnail/file.name..................Indicates.thumbnails.and.names.contained.in.a.folder.
Cursor........................................Indicates.the.selected.slide.
Scroll.bar...................................Used.to.view.folders.or.files.not.visible.in.the.window.
ꢂꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
Setting Option for Viewer
PLAY MODE:
MANUAL................. Views.a.slide.manually.when.the.Viewer.source.is.selected.
AUTO...................... Plays.back.slides.automatically.when.the.Viewer.source.is.selected.
INTERVAL:
Specifies interval time between 5 and 300 seconds.
START:
Specifies start screen when the Viewer source is selected.
SHOW THUMBNAILS:
Selecting the Viewer source will display a list of thumbnails of graphic files stored in the USB memory when [ON]
is selected. Selecting the Viewer source will display a list of icons of graphic files stored in the USB memory
when [OFF] is selected.
Sort:
Rearranges the slides or thumbnails by name, extension, date or size.
NOTE: This setting is not available for the following folders:
*Folders created with the “Output Viewer” feature of Ulead Photo Explorer 8.0 or with Viewer PPT Converter 3.0
OK/Cancel:
To close the Options menu with saving changes, select [OK] and press the ENTER button.
To close the Options menu without saving changes, select [CANCEL] and press the ENTER button.
THUMBNAILS menu
The THUMBNAILS menu will appear when you press the MENU button on the remote control or the projector
cabinet. To close the THUMBNAILS menu, press the EXIT button.
The THUMBNAILS menu includes the following commands:
Play..................... Plays.back.automatically.or.manually.depending.on.the.setting.in.Options..This.allows.you.to.move.on.to.
the.next.slide.when.[MANUAL].is.selected.in.the.[PLAy.MODE].
Logo................... Replace.the.default.background.logo.with.another.logo.in.JPEG,.BMP,.non-interlaced.GIF.or.non-inter-
laced.PNG.format.
Options............... Displays.the.Viewer.setting.options.
ꢂꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
Exiting Viewer
To exit Viewer, switch to another input such as Computer 1, Computer 2, Computer 3, Component, Video, S-Video
or NETWORK.
* To switch to another input, there are two ways:
•
•
Press the COMPUTER 1, COMPUTER 2, COMPUTER 3, COMPONENT, VIDEO, S-VIDEO or NETWORK
button on the remote control.
Press the MENU button on the remote control to display the Viewer menu. Press the MENU button again to
display the main menu and select the input from the [SOURCE] submenu.
With this function it is possible to switch directly to a slide when the picture of a VCR or computer is being projected.
Example: When conducting presentations using a combination of slides and moving pictures from a VCR, etc., it is
possible to switch from a Viewer slide to the video picture then back to the Viewer slide simply by using the VIEWER
button.
NOTE: Even if you switch the current Viewer source to another source, the current slide is retained. When you return back to the
Viewer, you will get the slide that has been retained.
ꢂ8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
Changing Background Logo
You can change the default background logo using the Viewer feature.
NOTE: File size must be 256KB or less. File formats other than JPEG, BMP, non-interlaced GIF or non-interlaced PNG are not
available.
Preparation: Store JPEG or BMP files (JPEG, BMP, non-interlaced GIF or non-interlaced PNG files) in a USB mem-
ory into the projector’s USB port.
NOTE: To change highlight from the Thumbnails screen (right window) to a directory tree (left window) , press the EXIT button.
To return highlight to the Thumbnails screen, press the ENTER button.
1. Use the SELECT
button to select a file (slide) for your background logo when displaying the
Thumbnail screen.
2. Press the MENU button to display the THUMBNAILS menu.
3. Use the SELECT button to select [LOGO] and then press the ENTER button.
a confirmation dialog box will be displayed.
4. Use the SELECT button to select [YES] and press the ENTER button. This completes changing a logo
for the background.
*
Once you have changed the background from the NEC logo to another, you cannot return the logo to back-
ground even by using [RESET]. To put the NEC logo back in the background logo, repeat the above steps. The
NEC logo file is included on the supplied User Supportware 5 CD-ROM (/Logo/NECPJ_BB_X.JPG).
ꢂ9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Using the Menus
1. Press the MENU button on the remote control or the projector cabinet to display the menu.
,
NOTE: The commands such as ENTER, EXIT in the bottom show available buttons for your operation.
2. Press the SELECT
buttons on the remote control or the projector cabinet to display the submenu.
3. Press the ENTER button on the remote control or the projector cabinet to highlight the top item or the
first tab.
4. Use the SELECT
to adjust or set.
buttons on the remote control or the projector cabinet to select the item you want
You can use the SELECT
want.
buttons on the remote control or the projector cabinet to select the tab you
5. Press the ENTER button on the remote control or the projector cabinet to display the submenu window.
6. Adjust the level or turn the selected item on or off by using the SELECT
control or the projector cabinet.
buttons on the remote
Changes are stored until you adjust it again.
7. Repeat steps 2 -6 to adjust an additional item, or press the EXIT button on the remote control or the pro-
jector cabinet to quit the menu display.
NOTE: When a menu or message is displayed, several lines of information may be lost, depending on the signal or settings.
8. Press the MENU button to close the menu.
To return to the previous menu, press the EXIT button.
ꢃ0
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Using ADVANCED menu and BASIC menu
The projector has two menu modes: the ADVANCED menu and the BASIC menu.
ADVANCED.menu... This.is.the.menu.that.contains.all.the.available.menus.and.commands..Users.with.an.ADMINISTRAOR.or.
ADVANCED.account.can.access.the.ADVANCED.menu.
BASIC.menu........... This.is.the.basic.menu.that.contains.minimum.essentials.of.menus.and.commands..Users.with.a.BASIC.
account.can.access.the.BASIC.menu.
See page 50 for settings available to ADVANCED and BASIC menus.
NOTE:
• A user with an ADMINISTRATOR account that has no password set is registered at the factory.
This will allow the user to access the ACCOUNT items without password entry.
• When using your USB mouse, click each number or alphabet.
BS: Delete the character before the cursor or highlight.
]
OK/[ : Confirm the keyword and close the Software keyboard.
Entering alphanumeric characters by using Software Keyboard
Enter alphanumeric characters to input a keyword in [LOGO LOCK] or [SECURITY].
[IP.ADDRESS,.PASSWORD].
[USER.NAME,.PROJECTOR.NAME].
[PASSWORD.OR.KEyWORD]
1.to.0.and.Characters
When using the remote control:
............................... Use.to.type.in.password.or.keyword.
1. Press the MENU, AUTO ADJ, SELECT , SE-
LECT , SELECT or SELECT button to se-
MODE..................... Selects.one.of.three.modes.for.num-
lect a character in the row.
bers,.alphabet.and.special.charac-
ters.
example: to enter “C”, press the seleCt
ton.
but-
SP........................... Inserts.a.space
2. Press the MENU, AUTO ADJ, SELECT , SE-
BS........................... Deletes.one.character.backward
<<........................... Returns.to.the.previous
>>........................... Advances.to.the.next
OK........................... Executes.the.selection
CANCEL.................. Cancels.the.selection
LECT , SELECT or SELECT button to se-
lect a character in the column.
example: to enter “C”, press the MenU button.
EXIT........................ Deletes.a.character.
ENTER.................... Makes.your.input.take.effect.and.
closes.the.input.screen.
When using the mouse:
Point to a character and click it.
[BS]........................ Deletes.a.character.
[
]......................... Makes.your.input.take.effect.and.
closes.the.input.screen.
ꢃ1
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Basic menu items are indicated by
shaded area.
Menu tree
Factory default settings are indi-
cated by the gray shaded area.
Menu
Item
SOURCE.
.
COMPUTER.1,.COMPUTER.2,.COMPUTER.3,.COMPONENT,.VIDEO,.S-VIDEO,.VIEWER,.NETWORK,.ENTRy.LIST
ADJUST.
PICTURE.
MODE.
STANDARD,.PROFESSIONAL
1.to.6
.
.
.
.
.
.
.
.
.
.
.
.
.
PRESET.
.
.
DETAIL.SETTINGS
.
GENERAL.
REFERENCE.
HIGH-BRIGHT,.PRESENTATION,.VIDEO,.
MOVIE,.GRAPHIC,.sRGB
.
.
.
.
.
.
.
..
.
.
.
..
GAMMA.CORRECTION
.
DyNAMIC,.NATURAL,.BLACK.DETAIL
5000,.6500,.7800,.8500,.9300,.10500
CONTRAST.RGB,.BRIGHTNESS.RGB.
.
.
..
COLOR.TEMPERATURE.
.
.
WHITE.BALANCE. .
.
CONTRAST.
BRIGHTNESS.
SHARPNESS
COLOR.
HUE.
.
.
.
.
.
.
.
.
.
.
.
.
RESET
.
IMAGE.OPTIONS. CLOCK
.
.
PHASE
.
.
HORIzONTAL.POSITION
VERTICAL.POSITION
OVERSCAN.
.
.
.
.
.
0%,.5%,.10%
RGB.
.
.
5:4,.4:3,.16:9,.16:10
.
.
ASPECT.RATIO.
.
4:3.SCREEN.(COMPONENT)/VIDEO/S-VIDEO
.
4:3,.LETTERBOX,.WIDE.SCREEN,.zOOM
.
.
WIDE.SCREEN.(COMPONENT)/VIDEO/S-VIDEO. 4:3.WINDOW,.LETTERBOX,.WIDE.SCREEN,.4:3.FILL
.
VIDEO.
NOISE.REDUCTION.
DEINTERLACE.
3D.y/C.SEPARATION.
CONTRAST.ENHANCEMENT
.
RANDOM.NR,.MOSQUITO.NR,.BLOCK.NR
AUTO,.VIDEO,.FILM
.
.
.
.
OFF,.ON
.
.
.
SOUND.
VOLUME,.BASS,.TREBLE,.BALANCE,.3D.SURROUND.(OFF,.ON)
SETUP.
BASIC.
KEySTONE.
CORNERSTONE.
PIP.
HORIzONTAL,.VERTICAL
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PIP.POSITION:.TOP-LEFT,TOP-RIGHT,.BOTTOM-LEFT,.BOTTOM-RIGHT.
OFF,.BLACKBOARD,.BLACKBOARD.(GRAy),.LIGHT.yELLOW,.LIGHT.GREEN,.LIGHT
BLUE,.SKy.BLUE,.LIGHT.ROSE,.PINK
.
WALL.COLOR.
.
.
.
LAMP.MODE.
OFF.TIMER.
TOOLS.
NORMAL,.ECO
.
OFF,.0:30,.1:00,.2:00,.4:00,.8:00,.12:00,.16:00
.
CORNERSTONE,.ENTRy.LIST,.[DATE.TIME,.PRESET],.[MOUSE],.[HELP]
.
LOGOFF
.
LANGUAGE.
.
ENGLISH,.DEUTSCH,.FRANçAIS,.ITALIANO,.ESPAñOL,.SVENSKA,.SUOMI,.NORSK,
.
NEDERLANDS,.TüRKçE,.POLSKI,.
.,.
.,.MAGyAR,.
.
.
PORTUGUêS,.
COLOR,.MONOCHROME
ON,.OFF
.,.
.,.DANSK,.
.,.
.,.
MENU.
COLOR.SELECT.
SOURCE.DISPLAy.
MESSAGE.DISPLAy.
TIME.DISPLAy.
MENU.DISPLAy.TIME.
BACKGROUND.
FILTER.MESSAGE.
.
.
.
.
.
.
ON,.OFF
ON,.OFF
MANUAL,.AUTO.5.SEC,.AUTO.15.SEC,.AUTO.45.SEC
BLUE,.BLACK,.LOGO
OFF,.100[H],.200[H],.500[H],.1000[H]
ꢃꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Menu
Item
SETUP.
INSTALLATION. ORIENTATION.
DESKTOP.FRONT,.CEILING.REAR,.DESKTOP.REAR,.CEILING.FRONT
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
SCREEN.
SECURITy.SETTINGS.
NETWORK.SETTINGS.
.
.
.
.
.
.
.
SCREEN.TyPE:.4:3.SCREEN,.WIDE.SCREEN./.POSITION
CONTROL.PANEL.LOCK,.LOGO.LOCK,.ACCOUNT.LOCK,.ACCOUNT,.SECURITy
GENERAL:..
PROJECTOR.NAME,.WIRED.LAN,.WIRELESS.LAN
.WIRED:..
.
.
DNS.CONFIGURATION,.RECONNECT
PROFILES,.DHCP,.IP.ADDRESS,.SUBNET.MASK,.GATEWAy,.
DNS.CONFIGURATION,.ADVANCED,.RECONNECT
HOST.NAME,.DOMAIN.NAME
.WIRELESS:.
.
DOMAIN:..
MAIL:..
.
.ALERT.MAIL,.SENDER’S.ADDRESS,.SMTP.SERVER.NAME
RECIPIENT’S.ADDRESS.1-3,.TEST.MAIL
COMMUNICATION.SPEED.4800bps,.9600bps,.19200bps,.38400bps
REMOTE.SENSOR.
STANDBy.MODE.
AUTO.ADJUST.
AUTO.START.
FRONT./.BACK,.FRONT,.BACK
NORMAL/POWER-SAVING
OFF,.NORMAL,.FINE
OFF,.ON
.
OPTIONS.
.
.
.
.
.
.
.
.
.
POWER.MANAGEMENT. OFF,.0:05,.0:10,.0:20,.0:30
FAN.MODE. AUTO,.HIGH,.HIGH.ALTITUDE
DEFAULT.SOURCE.SELECT. LAST,.AUTO,.COMPUTER1,.COMPUTER2,.COMPUTER3,.COMPONENT,.VIDEO,
.
S-VIDEO,.VIEWER,.NETWORK
SIGNAL.SELECT.
.
COLOR.SySTEM.
OUT.TERMINAL.
COMPUTER1.
COMPUTER2.
VIDEO,.S-VIDEO
RGB/COMPONENT,.RGB,.COMPONET
RGB/COMPONENT,.RGB,.COMPONET
LAST,.COMPUTER1,.COMPUTER2,.COMPONENT
INFORMATION. USAGE.TIME.
LAMP.LIFE.REMAINING,.LAMP.HOURS.USED,.FILTER.HOURS.USED
INPUT.TERMINAL,.SIGNAL.TyPE,.VIDEO.TyPE,.SOURCE.NAME,.ENTRy.NO.
HORIzONTAL.FREQUENCy,.VERTICAL.FREQUENCy,.SyNC.TyPE,.SyNC.POLARITy,.SCAN.TyPE
IP.ADDRESS,.SUBNET.MASK,.GATEWAy,.MAC.ADDRESS
.
SOURCE.(1).
SOURCE.(2).
WIRED.LAN.
WIRELESS.LAN.(1
.
.
.
)
. IP.ADDRESS,.SUBNET.MASK,.GATEWAy,.MAC.ADDRESS
.
WIRELESS.LAN.(2). SSID,.NETWORK.TyPE,.WEP/WPA,.CHANNEL,.SIGNAL.LEVEL
.
.
VERSION.(1).
VERSION.(2).
.
PRODUCT,.SERIAL.NUMBER,.LAN.UNIT.TyPE,.LAN.UNIT.VERSION
FIRMWARE,.DATA,.FIRMWARE2,.DATA2
CURRENT.SIGNAL,.ALL.DATA,.ALL.DATA.(INCLUDING.ENTRy.LIST),.CLEAR.LAMP.HOURS,.CLEAR.FILTER.HOURS
RESET.
ꢃꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Menu Elements
tab
slide bar
highlight
available buttons
Currently selected
user
Currently selected
source
help button
Close button
solid triangle
radio button
Check box
OK button
Cancel button
return symbol
menu windows or dialog boxes typically have the following elements:
Highlight................. Indicates.the.selected.menu.or.item..
Solid.triangle.......... Indicates.further.choices.are.available..A.highlighted.triangle.indicates.the.item.is.active..
Tab.......................... Indicates.a.group.of.features.in.a.dialog.box..Selecting.on.any.tab.brings.its.page.to.the.front.
Radio.button........... Use.this.round.button.to.select.an.option.in.a.dialog.box.
Check.box............... Place.a.checkmark.in.the.square.box.to.turn.the.option.On..
Slide.bar................. Indicates.settings.or.the.direction.of.adjustment.
OK.button............... Press.to.confirm.your.setting..you.will.return.to.the.previous.menu.
Cancel.button.......... Press.to.cancel.your.setting..you.will.return.to.the.previous.menu.
Close.button........... Click.to.close.the.window.and.saving.changes.(USB.mouse.only).
Help.button............. Indicates.that.help.about.that.feature.is.available.(USB.mouse.only)..Press.the.HELP.button.on.the.remote.
control.to.display.help.
Return.symbol........ Indicates.the.software.keyboard.is.available.
ꢃ4
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Menu Descriptions & Functions [SOURCE]
COMPUTER 1 and 2
Selects the computer connected to your COMPUTER 1 or COMPUTER 2 input connector signal.
NOTE: An optional component cable (Component V or ADP-CV1 cable) is needed for a component signal.
COMPUTER 3 (RGB Digital)
Selects the computer connected to your COMPUTER 3 (DVI-D) connector.
COMPONENT
Selects what is connected to your COMPONENT IN (Y, Cb/Pb, Cr/Pr).
VIDEO
Selects what is connected to your VIDEO input-VCR, laser disc player, DVD player or document camera.
S-VIDEO
Selects what is connected to your S-VIDEO input-VCR, DVD player, or laser disc player.
NOTE: A frame may freeze for a brief period of time when a video is played back in fast-forward or fast-rewind with a Video or
S-Video source.
VIEWER
This feature enables you to make presentations using a USB memory that contains captured images and slides cre-
ated with the exclusive Ulead Photo Explorer 8.0 for NEC contained on the CD-ROM. See the supplied NEC Wired
and Wireless Network Setup Guide for installing the Ulead Photo Explorer 8.0 for NEC.
See page 63 for viewing slides.
NETWORK
Selects a signal from the LAN port (RJ-45) or the installed USB wireless LAN unit.
When a source connected on a network is not made settings, the [NETWORK] menu will be displayed. See the fol-
lowing pages.
ENTRY LIST
Displays a list of signals. ( page 76)
→
ꢃ5
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[ENTRY LIST]
Using the Entry List
When any source adjustments are made, the adjustments are automatically registered in the Entry List. The (adjust-
ment values of) registered signals can be loaded from the Entry List whenever necessary.
However, only up to 100 patterns can be registered in the Entry List. When 100 patterns have been registered in the
Entry List, an error message is then displayed and no additional patterns can be registered. You should thus delete
(adjustment values of) signals that are no longer needed.
Entering the Currently projected Signal into the Entry List
1. Display the Entry List.
2. Use the SELECT or button on your remote control or the projector cabinet to select any number.
3. Use the SELECT button to select [STORE] and press the ENTER button.
You can edit signals on the [ENTRY LIST].
LOAD...................... Enables.you.to.select.a.signal.from.the.list.
STORE.................... Enables.you.to.store.the.currently.projected.signal.
CUT......................... Enables.you.to.remove.a.selected.signal.from.the.list.and.place.it.on.the.“clipboard”.in.the.projector.
COPy...................... Enables.you.to.copy.a.selected.signal.from.the.list.and.place.it.on.the.“clipboard”.in.the.projector.
PASTE..................... Enables.you.to.paste.the.signal.placed.on.the.“clipboard”.to.any.other.line.of.the.list.
EDIT........................ Enables.you.to.change.SOURCE.NAME,.INPUT.TERMINAL,.LOCK,.and.SKIP.
ꢃꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
.
Source NaMe:
Enter.a.signal.name..Up.to.18.alphanumeric.characters.can.be.used.
INput terMINal:
Change.the.input.terminal.
lock:
Set.so.that.the.selected.signal.cannot.be.deleted.when.[ALL.DELETE].is.executed..After.executing.[LOCK],.
the.changes.cannot.be.saved.
SkIp:
Set.so.that.the.selected.signal.will.be.skipped.during.auto.search.
When.complete,.select.OK.and.press.ENTER..To.exit.without.storing.the.setting,.select.Cancel..Select.
[SOURCE.NAME].and.press.ENTER.to.display.the.Source.Name.Edit.window..you.can.change.source.
name.on.this.window..Press. .to.display.the.software.keyboard,.which.you.can.enter.alphanumeric.
characters..
ALL.DELETE............ This.feature.enables.you.to.delete.all.the.registered.signals.in.the.Entry.List.
PAGE.UP/.PAGE.DOWN... Enables.you.to.go.to.the.next.page.or.the.previous.page.
The following buttons are not available for the currently projecting signals:
1) The CUT and PASTE buttons on the [ENTRY LIST] screen
2) The INPUT TERMINAL button on the [ENTRY EDIT] screen
NOTE: When all the signals in the [ENTRY LIST] are deleted, the currently projected signal will be also deleted except locked sig-
nals.
ꢃꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Menu Descriptions & Functions [ADJUST]
[PICTURE]
[mODE]
This function allows you to determine how to save settings for [DETAIL SETTINGS] of [PRESET] for each input.
STANDARD............. Saves.settings.for.each.item.of.[PRESET].(Preset.1.through.6)
PROFESSIONAL...... Saves.all.the.settings.of.[PICTURE].for.each.input..
[pRESET]
This option allows you to adjust neutral tint for yellow, cyan or magenta. There are six factory presets optimized for
various types of images, you can set user adjustable settings.
ꢃ8
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[DETAIL SETTINGS]
This will provide you with three pages of menus that provide more detailed settings.
[GENERAL]
Selecting Reference Setting [REFERENCE]
This feature allows you to use color correction or gamma values as reference data to optimize for various types
of images.You can select one of the following six settings.
HIGH-BRIGHT..... Recommended.for.use.in.a.brightly.lit.room.
PRESENTATION.. Recommended.for.making.a.presentation.using.a.PowerPoint.file.
VIDEO................. Recommended.for.typical.TV.program.viewing.
MOVIE................. Recommended.for.movies.
GRAPHIC............ Recommended.for.graphics.
sRGB................... Standard.color.values.
Selecting Gamma Correction Mode [GAMMA CORRECTION]
Each mode is recommended for:
DyNAMIC............ Creates.a.high-contrast.picture.
NATURAL............ Natural.reproduction.of.the.picture.
BLACK.DETAIL.... Emphasizes.detail.in.dark.areas.of.the.picture.
Adjusting Color Temperature [COLOR TEMPERATURE]
This option allows you to select the color temperature of your choice.
NOTE:
• When [PRESENTATION] or [HIGH-BRIGHT] is selected in [REFERENCE], this function is not available.
• When [WHITE BALANCE] settings has been changed, the color temperature value on screen does not reflect the real color
temperature.
[WHITE BALANCE]
Adjusting White Balance [WHITE BALANCE]
This allows you to adjust the white balance. Contrast for each color (RGB) to adjust the white level of the screen;
Brightness for each color (RGB) is used to adjust the black level of the screen.
ꢃ9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[CONTRAST]
Adjusts the intensity of the image according to the incoming signal.
[BRIGhTNESS]
Adjusts the brightness level or the back raster intensity.
[ShARpNESS]
Controls the detail of the image for Video.
NOTE: Although the use of the SHARPNESS control will provide a sharper or softer picture, the actual change may not be dra-
matic, depending on the resolution of an input signal.
[COLOR]
Increases or decreases the color saturation level (not valid for RGB and digital signals).
[hUE]
Varies the color level from +/- green to +/-blue. The red level is used as reference. This adjustment is only valid for
Video, Component and TV standard inputs (not valid for RGB and digital signals).
Input signal
Contrast
Brightness
Sharpness
Color
Hue
Computer (RGB analog)
Computer (RGB digital)
Component
Video, S-Video
Viewer, Network
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
Yes
Yes
No
No
No
Yes
Yes
No
Yes=Adjustable, No=Not adjustable
[RESET]
The settings and adjustments for [PICTURE] will be returned to the factory settings with the exception of the following;
Preset numbers and [REFERENCE] within the [DETAIL SETTINGS] screen when [STANDARD] is selected in [MODE].
The settings and adjustments under [DETAIL SETTINGS] within the [PRESET] screen that are not currently select-
ed will not be reset.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[IMAGE OPTIONS]
Adjusting Clock and phase [CLOCK/phASE]
This allows you to manually adjust CLOCK and PHASE.
CLOCK.................... Use.this.item.to.fine.tune.the.computer.image.or.to.remove.any.vertical.banding.that.might.appear..This.
function.adjusts.the.clock.frequencies.that.eliminate.the.horizontal.banding.in.the.image.
This.adjustment.may.be.necessary.when.you.connect.your.computer.for.the.first.time.
PHASE.................... Use.this.item.to.adjust.the.clock.phase.or.to.reduce.video.noise,.dot.interference.or.cross.talk..(This.is.
evident.when.part.of.your.image.appears.to.be.shimmering.)
Use.[PHASE].only.after.the.[CLOCK].is.complete.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Adjusting horizontal/Vertical position [hORIZONTAL/VERTICAL pOSITION]
Adjusts the image location horizontally and vertically.
Selecting Overscan percentage [OVERSCAN]
Select overscan percentage (0%, 5% and 10%) for signal.
Projected image
Overscaned by 10%
8ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Selecting Aspect Ratio [ASpECT RATIO]
.
Screen.Type.4:3.SCREEN.(VIDEO).
Screen.Type.WIDE.SCREEN.(VIDEO).
RGB
Aspect Ratio allows you to select the best Aspect mode to display your source image.
When screen type 4:3 SCREEN is selected for the source, the following selections will display:
For VIDEO
4:3.......................... Standard.4:3.aspect
LETTERBOX............ Reduced.to.display.the.true.aspect.with.black.borders.on.top.and.bottom
WIDE.SCREEN........ Left.&.Right.stretched.with.black.borders.on.top.and.bottom
zOOM..................... Left.&.Right.stretched..Left.&.Right.sides.cut..Available.for.4:3.only.
When screen type WIDE SCREEN is selected for the source, the following selections will display:
For VIDEO
4:3.WINDOW.......... Reduced.to.display.the.true.aspect.with.black.borders.on.right.and.left
LETTERBOX............ Standard.16:9.aspect
WIDE.SCREEN........ Left.and.right.stretched.to.display.the.true.aspect
4:3.FILL.................. Stretched.to.display.in.16:9.aspect.ratio
For RGB
4:3.......................... For.a.video.signal.with.an.aspect.ratio.of.4:3
5:4.......................... For.a.video.signal.with.an.aspect.ratio.of.5:4
16:9........................ For.a.video.signal.with.an.aspect.ratio.of.16:9
16:10...................... For.a.video.signal.with.an.aspect.ratio.of.16:10
NOTE: You can adjust image position vertically for a source with black borders on top and bottom. (→ page 93)
NOTE: Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue
such as a coffee shop or hotel and employing compression or expansion of the screen image with a [ASPECT RATIO] or [SCREEN]
setting may raise concern about the infringement of copyrights which are protected by copyright law.
Input
Signal
Screen
Type
Letterbox
Squeeze
4:3
4:3
Letterbox
Letterbox
Wide Screen
4:3 SCREEN
WIDE SCREEN
Zoom
4:3 Window
4:3 Fill
Wide Screen
8ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
16:10
4:3
5:4
16:9
Input Signal
Screen Type
4:3
4:3
16:10
16:10
5:4
5:4
16:9
16:9
4:3
SCREEN
WIDE
SCREEN
[VIDEO]
Using Noise Reduction [NOISE REDUCTION]
This function is used to reduce video noise.
RANDOM.NR.......... Reduces.flickering.random.noise.in.an.image..
MOSQUITO.NR....... Reduces.mosquito.noise.that.appears.around.the.edges.of.an.image.during.DVD.playback.
BLOCK.NR.............. Reduces.block.noise.or.mosaic-like.patterns.by.selecting.ON.
Selecting Interlaced progressive Conversion process mode [DEINTERLACE]
This function allows you to select an interlaced-to-progressive conversion process for video signals.
AUTO...................... Determines.an.appropriate.interlaced-to-progressive.conversion.process.automatically.
VIDEO..................... Applies.a.normal.interlaced-to-progressive.conversion.process.
FILM....................... Applies.the.automatic.detection.mode.for.telecine.signals..This.option.is.recommended.for.a.movie pic-
ture.
NOTE: This function is not available with RGB signals.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Turning On or Off the ꢁD Dimensional Separation [ꢁDY/C SEpARATION]
When projecting an image from a VIDEO input, set to ON to project the highest quality image.
OFF......................... Turns.off.the.3.dimensional.separation.feature.
ON.......................... Turns.on.the.3.dimensional.separation.feature.
NOTE: Only available for NTSC 3.58 video signals.
Adjusting Contrast Enhancement [CONTRAST ENhACEmENT]
This function uses properties of the eye to improve picture contrast.
Adjust this function to the desired level of enhancement.
[SOUND]
Controlling Sound [VOLUmE/BASS/TREBLE/BALANCE]
Adjusts the volume, bass and treble level, left and right balance of the projector speaker and AUDIO OUT (Stereo
Mini Jack).
Enabling ꢁD Surround [ꢁD SURROUND]
Turn on or off the 3D surround effect.
If the AUDIO OUT stereo mini jack of the projector is connected to external equipment, adjusting the sound on the
external equipment can cause sound to be distorted or cracked, depending on the bass, treble or 3D Surround
adjustment. If this happens, return the adjustments of the projector to the factory default (Bass:0, Treble: 0, 3D Sur-
round: Off).
85
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Menu Descriptions & Functions [SETUP]
[BASIC]
Selecting Keystone mode [KEYSTONE]
This feature allows you to correct keystone distortion.
Selecting this item will display the Keystone setting menu.
You can correct vertical distortion manually from the menu. ( page 29)
→
Changes will be saved even when you turn off the projector.
NOTE: When [CORNERSTONE] is selected, [KEYSTONE] is not available.
8ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Selecting Cornerstone mode [CORNERSTONE]
This option allows you to correct trapezoidal distortion.
Selecting this item will display the Cornerstone adjustment screen. ( page 39)
→
NOTE: When [KEYSTONE] is selected, [CORNERSTONE] is not available.
Using the pIp Function
This function allows you to view two different signals simultaneously.
PIP POSITION:
This option allows you to select the position of a sub picture in the main picture.
The options are: top-left, top-right, bottom-left, and bottom-right. ( page 42)
→
8ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Using the Wall Color Correction [WALL COLOR]
This function allows for quick adaptive color correction in applications where the screen material is not white.
The following nine options are available.
Setting Lamp mode to Normal or Eco [LAmp mODE]
This feature enables you to select two brightness modes of the lamp: Normal and Eco modes. The lamp life can be
extended by using the Eco mode. Selecting Eco mode decreases fan noise when compared to Normal mode.
Lamp Mode
Description
Status of LAMP indicator
Off
Normal Mode This is the default setting (100%
Brightness).
Eco Mode
Select this mode to increase the lamp
life (approx. 80% Brightness (light output)
on NP3150 and approx. 88% Brightness
(light output) on NP2150/NP1150).
Steady Green light
NOTE: If the projector is overheated in Normal mode, there may be a case where the Lamp mode will be forced into the Eco mode
to protect the projector. This mode is called “forced Eco mode”.
When the projector is in forced Eco mode, the picture brightness decreases. The LAMP indicator’s steady green light indicates the
lamp is in Eco mode.
When the projector comes back to normal temperature, the Lamp mode returns to Normal mode.
In the forced Eco mode, changing [LAMP MODE] setting in the menu will not affect the actual lamp mode.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Using Off Timer [OFF TImER]
1. Select your desired time between 30 minutes and 16 hours: OFF, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00.
2. Press the ENTER button on the remote control.
3. The remaining time starts counting down.
4. The projector will turn off after the countdown is complete.
NOTE:
• To cancel the preset time, set [OFF] for the preset time or turn off the power.
• When the remaining time reaches 3 minutes before the projector is turned off, the [THE PROJECTOR WILL TURN OFF WITHIN
3 MINUTES] message will be displayed on the bottom of the screen.
[TOOLS]
Using [CORNERSTONE]
(
→
page 39)
Using [ENTRY LIST]
(
→
page 76)
Setting the Current Date and Time [DATE,TImE, pRESET]
You can set the current time, month, date, and year.
NOTE: The projector has a built-in clock. The clock will keep working for about 2 weeks after the main power is turned off. If the
main power is off for 2 weeks or more, the built-in clock will cease. If the built-in clock ceases, set the date and time again. The
built-in clock will not cease while in the standby mode.
TIME ZONE: Select your time zone.
DAYLIGHT SAVING TIME: Place a check mark to adjust the clock for daylight saving changes.
INTERNET TIME SERVER: Place a check mark to turn on clock synchronization. When this option is turned on, the
projector’s built-in clock will be synchronized with an Internet timer server in every 24 hours and at the time of pro-
jector’s start up.
UPDATE button: Synchronizes the projector’s built-in clock immediately.
The UPDATE button is not available unless the INTERNET TIME SERVER check box is turned on.
Setting mouse pointer, Button and Sensitivity [mOUSE]
This option lets you to change your USB mouse settings. The mouse settings feature is available for USB mouse
only. Choose the settings you want:
MOUSE.BUTTON.... [RIGHT.HAND].or.[LEFT.HAND]
MOUSE.SENSITIVITy... [FAST],.[MEDIUM].or.[SLOW]
Using [hELp]
(
→
page 35)
89
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Logging OffYour projector [LOGOFF]
This feature allows you to log off your projector without turning it off.
Logging off your projector will prevent an unauthorized user from operating your projector.
To log off your projector, follow the steps below.
1. Press the MENU button and use the SELECT button to highlight [SETUP].
2. Use the SELECT or the ENTER button to highlight [BASIC].
3. Use the SELECT button to highlight [LOGOFF], and press the ENTER button.
the [lOg Off PrOJeCtOr /are YOU sUre?] message will be displayed.
4. Select [YES] and press the ENTER button to log off your projector and close the menu, and then the
LOGON screen will be displayed.
NOTE:
• When selecting [NO] and press the ENTER button, you will return to the Logoff screen in Step 2.
to log on your projector, select a user name, then enter your password and select [OK] and press the enter
button.
the lOgOn screen will close. logging on your projector is done.
NOTE:
The default LOGON screen will be shown as follows:
USER NAME → ADMINISTRATOR
PASSWORD → No setting
See “Limiting Access Level to Available Menu Items” on page 50 for entering a user name and assigning a password.
Selecting menu Language [LANGUAGE]
You can choose one of 21 languages for on-screen instructions.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[MENU]
Selecting menu Color [COLOR SELECT]
You can choose between two options for menu color: color and monochrome.
Turning On / Off Source Display, message and Time [SOURCE DISpLAY], [mESSAGE DISpLAY],
[TImE DISpLAY]
SOURCE.DISPLAy.........This.option.turns.on.or.off.input.name.display.such.as.Computer.1,.Computer.2,.Computer.3,.Compo-
nent,.Video,.and.No.Input.to.be.displayed.on.the.top.right.of.the.screen.
MESSAGE.DISPLAy..........This.option.turns.on.or.off.messages..Even.though.selecting.[OFF],.the.following.message.will.appear.
.
•.“Projector.is.locked”..When.the.projector.security.is.unlocked,.the.message.will.disappear.
TIME.DISPLAy...............This.option.turns.on.or.off.the.current.time.displayed.on.the.top.left.of.the.screen.
NOTE: The source and current time will be displayed for the time specified in [MENU DISPLAY TIME]. When [MANUAL] is se-
lected in [DISPLAY TIME], the source and current time will be always displayed.
Selecting menu Display Time [mENU DISpLAY TImE]
This option allows you to select how long the projector waits after the last touch of a button to turn off the menu. The
preset choices are [MANUAL], [AUTO 5 SEC], [AUTO 15 SEC], and [AUTO 45 SEC]. The [AUTO 45 SEC] is the
factory preset.
Selecting a Color or Logo for Background [BACKGROUND]
Use this feature to display a blue/black screen or logo when no signal is available. The default background is blue.
You can change the logo screen using the Viewer feature. ( page 69)
→
NOTE: When the DVI [COMPUTER 3(DVI-D) IN] input is selected with no signal, the blueback is displayed in regardless of the set-
ting [LOGO].
Selecting Interval Time for Filter message [FILTER mESSAGE]
This option allows you to select the time preference between displaying the message for cleaning the filters. Clean
the filter when you get the message “Please clean filter.” ( page 116)
→
Five options are available: Off, 100[H], 200[H], 500[H], 1000[H]
The default setting is 500[H].
NOTE: The message for filter cleaning will be displayed for one minute when the projector is turned on or off. To cancel the mes-
sage, press any button on the projector cabinet or the remote control.
NOTE: Your setting will not be affected even when [RESET] is done from the menu.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[INSTALLATION]
Selecting projector Orientation [ORIENTATION]
This reorients your image for your type of projection. The options are: desktop front projection, ceiling rear projec-
tion, desktop rear projection, and ceiling front projection.
DESKTOP FRONT
CEILING REAR
DESKTOP REAR
CEILING FRONT
9ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Selecting Aspect Ratio and position for Screen [SCREEN]
SCREEN.TyPE........ Select.one.of.two.options:.4:3.SCREEN.or.WIDE.SCREEN.for.the.screen.to.be.used..See.also.[ASPECT.
RATIO].
(→.page.83)
POSITION............... This.feature.allows.you.to.adjust.the.vertical.position.of.the.image.when.WIDE.SCREEN.has.been.selected.
for.the.screen.type.
When.WIDE.SCREEN.has.been.selected.there.is.no-signal.area.above.and.below.the.image.
no-signal area
NOTE: This option is available only when [WIDE SCREEN] is selected in [SCREEN TYPE].
NOTE:
• After changing the screen type, check the setting of [ASPECT RATIO] in the menu. (→page 83)
• [POSITION] is not available when [4:3 SCREEN] is selected for [SCREEN TYPE] or when [LETTERBOX] is selected for [ASPECT
RATIO].
9ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Setting Security [SECURITY SETTINGS]
Disabling the Cabinet Buttons [CONTROL pANEL LOCK]
This option turns on or off the Control Panel Lock function.
NOTE:
• This Control Panel Lock does not affect the remote control functions.
• When the control panel is locked, pressing and holding the EXIT button on the projector cabinet for about 10 seconds will
change the setting to [OFF].
Setting a password [LOGO LOCK]
A password can be set for your projector to avoid operation by an unauthorized person.
When [LOGO LOCK] is set, doing any one of the following two operations will display the Password input screen.
•
•
Changing the background from or to [LOGO]
Changing the logo data in a USB memory.
[ENTRY]
To assign your password:
NOTE: Up to 10 alphanumeric characters can be assigned.
1. Type a password.
Select the [ENTER PASSWORD] entry box and press the ENTER button. (→ page 71)
An asterisk will be displayed.
The Software keyboard appears. Use the Software keyboard to type a password on the [ENTER PASS-
WORD] screen and press the ENTER button.
The [CONFIRM PASSWORD] screen will be displayed.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
2. Type the same password again and press the ENTER button.
Your password will be assigned.
[DELETE]
To delete your password:
1. Select [DELETE PASSWORD] and press the ENTER button.
2. Enter your password.
An asterisk will be displayed.
3. Press the ENTER button.
Your password will be deleted.
NOTE:
* Do not forget your password. However, if you forget your keyword, NEC or your dealer will provide you with your Release Code
upon proof of ownership.
* The [LOGO LOCK] will not be affected even when [RESET] is done from the menu.
ACCOUNT LOCK
When [ACCOUNT LOCK] is set to [ON], you can set it to [OFF].
When [ACCOUNT LOCK] is set to [OFF], you can set it to [ON].
The [ACCOUNT] setting is available only when [ACCOUNT LOCK] is set to [OFF].
ACCOUNT
See page 50.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[SECURITY]
The Security function enables you to protect your projector so that the projector will not project a signal unless you
enter a keyword. There is also an option to lock the projector by using a registered USB memory* as a protect key.
Once you have registered your USB memory as a protect key, you are required to insert the registered USB mem-
ory into the USB port of the projector each time you turn on the projector. You can enable the Security function by
using a keyword only. ( page 44)
→
*
The projector does not support NTFS formatted USB memory device.
Be sure to use a USB memory device formatted with the FAT32, FAT16 or FAT file system.
To format your USB memory device in your computer, refer to the document or help file that comes with your
Windows.
ON/OFF................... This.turns.the.Security.function.on.or.off.
KEyWORD.............. Enter.an.appropriate.keyword.when.you.use.the.Security.function..(Up.to.10.characters.can.be.used.).The.
Security.function.is.available.only.when.your.password.is.entered.
USE.PROTECT.KEy... Check.this.box.to.lock.your.projector.when.using.a.USB.memory..To.use.a.keyword.without.a.USB.mem-
ory,.do.not.check.this.box.
READ...................... Reads.data.from.a.USB.memory.
REGISTER............... Registers.data.from.the.USB.memory..The.Security.function.is.not.available.unless.at.least.one.USB.
memory.is.registered..(if.the.[USE.PROTECT.KEy].check.box.is.selected).Up.to.5.USB.memory.devices.
can.be.registered.
DELETE................... Deletes.data.of.a.registered.USB.memory.
To set up a keyword to enable the Security function without using a registered USB memory.
1. Use the SELECT or button to select [PASSWORD] and use the software keyboard to enter a keyword.
NOTE: Please make a note of your password.
2. Use the SELECT or button to select [OFF] and then use the SELECT or to select [ON].
3. Use the SELECT or button to select [OK] , then press the ENTER button.
The [AREYOU SURE?] message will appear.
4. Use the SELECT or button to select [YES] and press the ENTER button.
The Security function takes effect.
9ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
To register a USB memory device as a protect key.
preparation: Insert the USB memory device into the USB port (type A) of the projector.
1. Use the SELECT or button to select [USE PROTECT KEY] and press the ENTER button.
2. Use the SELECT or button to select [READ] and press the ENTER button.
Data of the USB memory will be read into the projector.
3. Use the SELECT or button to select [REGISTER] and press the ENTER button.
Downloaded data will be registered and be displayed in the list window.
4. Use the SELECT or button to select [KEYWORD] and use the software keyboard to enter a password.
NOTE: Please make a note of your password.
5. Use the SELECT or button to select [OFF] and then use the SELECT or to select [ON].
6. Use the SELECT or button to select [OK] , then press the ENTER button.
The [AREYOU SURE?] message will appear.
7. Use the SELECT or button to select [YES] and press the ENTER button.
The Security function takes effect.
To turn on the projector when Security is enabled (when using your password only).
1. Press and hold the POWER button for a minimum of two seconds.
The projector will be turned on and a message to the effect that the projector is security-protected will
be displayed.
2. Press the MENU button.
The Release Code input screen will be displayed.
3. Enter your keyword in the Release Code input screen.
You can view the projected image.
NOTE: Do not forget your password. However, if you forget your keyword, NEC or your dealer will provide you with your Release
Code. See more information at the end of this section.
To turn on the projector when Security is enabled (when using USB memory device as a protect
key).
preparation: Insert the registered USB memory device into the USB port (type A) of the projector.
Press and hold the POWER button for a minimum of two seconds.
The projector will turn on and then recognize the USB memory device. Once the image has been projected, it will
stay on without the USB memory device.
•
the projector does not support ntfs formatted UsB memory device.
Be sure to use a UsB memory device formatted with the fat32, fat16 or fat file system.
to format your UsB memory device in your computer, refer to the document or help file that comes with your
Windows.
•
•
We do not warrant that the UsB port of the projector will support all UsB memory devices in the market.
When the projector is turned on, if the registered UsB memory device is not inserted into the projector, no
signal will be displayed with a message to the effect that the projector is security-protected. to turn off the se-
curity protection, insert the registered UsB memory device into the projector.
9ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
•
•
the security disable mode is maintained until the main power is turned off (by setting the main power switch
to “O” or unplugging the power cord). in the following cases you will be asked to check the protect key or input
the password:
(1)When [OK] is selected at an image for which security is set and the power is turned off then back on
(2)When the main power is turned off then back on while the security function is enabled
(3)When you attempt to display an image for which security is set while the security function is enabled
Blanks (spaces) cannot be used in the Keyword section.
To delete USB memory data you registered.
1. Use the SELECT or button to select [DELETE] and use the SELECT button to select the list window.
2. Use the SELECT or button to select the information on the USB memory device you wish to delete.
3. Press the SELECT button to select [DELETE] and press the ENTER button.
The information on the USB memory device will be deleted.
If you’ve lost your registered USB memory, proceed as follows:
1. Press and hold the POWER button for a minimum of two seconds.
The projector will be turned on and display a message to the effect that the projector is security-protected.
2. Press the MENU button.
The Release Code input screen will be displayed as well as your Request Code (24 alphanumeric charac-
ters).
NOTE: NEC or your dealer will provide you with your Release Code in exchange for your registered password and Request Code.
See more information at the end of this section.
3. Enter your Release Code in the Release Code Input screen.
The security protection will be turned off.
NOTE:
• Some brands of USB memory devices cannot be used as a protect key.
• You should register one or more USB memory devices in case your registered USB memory device is damaged or stolen. Up to
5 pieces can be registered.
• Once the registered USB memory device has been formatted, the USB memory device cannot be recognized as your registered
protect key.
The Security will not be disabled by using [RESET].
NOTE:
For additional information visit:
US : http://www.necdisplay.com/
Europe : http://www.nec-display-solutions.com/
Global : http://www.nec-pj.com/
98
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[NETWORK SETTINGS]
This feature allows you to set various setting items when the projector is used on your network.
CAUTION
• Consult with your network administrator about these settings.
• The NP3150/NP2150/NP1150 series projectors distributed in some areas and countries do not come
standard with the USB Wireless LAN Unit.
If you purchase the projector without the USB Wireless LAN Unit installed and need to present to the pro-
jector via a wireless connection, the optional USB Wireless LAN Unit must be installed.
hints on how to Set Up LAN Connection
To configure the projector to communicate on the network using the LAN port (RJ-45) or Wireless LAN Unit:
1. Select the [WIRED] tab for the LAN port (RJ-45) or the [WIRELESS] tab for the Wireless LAN Unit.
2. On the [WIRED] tab or the [WIRELESS] tab, select a number from the [PROFILES] list for your LAN
settings.
Two settings can be stored in memory for each the LAN port and the Wireless LAN Unit respectively.
3. On the [WIRED] tab or the [WIRELESS] tab, turn on or off [DHCP], specify IP address, Subnet Mask,
Gateway and DNS Configuration. Select [OK] and press the ENTER button.
(
→
page 102, 103)
To recall the settings from memory:
After selecting the [WIRED] tab or the [WIRELESS] tab, select the number from the [PROFILES] list.
Select [OK] and press the ENTER button. ( page 102, 103)
→
To connect a DHCP server:
On the [WIRED] tab or the [WIRELESS] tab, select [DHCP] and press the ENTER button. A check mark will be
placed. Select again and press the ENTER button. The check box will be cleared.
When setting an IP address without using a DHCP server, clear the check box for [DHCP]. ( page 102, 103)
→
To set only for wireless LAN (NETWORK TYPE and WEP/WPA):
1. On the [WIRELESS] tab, select [PROFILES] and then select [PROFILE 1] or [PROFILE 2].
2. On the [WIRELESS] tab, select [ADVANCED] and press the ENTER button. The [ADVANCED] menu
will be displayed.
(
page 104, 105)
→
To select a wireless LAN access point:
1. On the [WIRELESS] tab, select [PROFILES] and then select [PROFILE 1] or [PROFILE 2].
2. On the [WIRELESS] tab, select [ADVANCED] and press the ENTER button.
3. On the Advanced menu, select [CONNECTION]
4. Select an SSID which you can access.
[SITE SURVEY] and press the ENTER button.
→
To select an SSID, highlight [SSID] and use the SELECT
to select [OK] and press the ENTER but-
ton. When you do not use [SITE SURVEY], simply enter an SSID and [INFRASTRUCTURE] or [AD
HOC]. ( page 104)
→
99
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
To receive error messages or information on the remaining lamp life via e-mail:
1. On the [MAIL] tab, select [ALERT MAIL] and press the ENTER button. A check mark will be placed.
2. Set [SENDER’S ADDRESS], [SMTP SERVER NAME] and [RECIPIENT’S ADDRESS]. Select [OK] and
press the ENTER button.
(
page 107)
→
To execute [Easy Connection] using Image Express Utility 2.0:
The [Easy Connection] is a mode that can abbreviate the troublesome LAN settings when using the Image Ex-
press Utility 2.0 and connecting the PC and projector via a wireless LAN.
The Image Express Utility 2.0 is contained on the supplied User Supportware 5 CD-ROM. To use [EASY CON-
NECTION], select [WIRELESS]
[PROFILES]
[EASY CONNECTION]. ( page 103)
→
→
→
NOTE: This function can be used when Windows XP is used as the OS and when you have a “Computer Administrator” privi-
lege. If the OS is Windows Vista, input of logon password as “Administrator” may be prompted.
[GENERAL]
This page allows you to specify a unique projector name and to check the current status of the LAN settings.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[pROJECTOR NAmE]
Specify a unique projector name. Press to display the software keyboard and type in. Up to 16 alphanumeric
characters, signs and symbols can be used. After entering a name, select [OK] and press the ENTER button.
NOTE: The [PROJECTOR NAME] will not be affected even when [RESET] is done from the menu.
Using Software Keyboard
1.to.0.and
Characters........ Use.to.type.in.password.or.keyword.
MODE..................... Selects.one.of.three.modes.for.numbers,.alphabet.and.special.characters.
SP........................... Inserts.a.space
BS........................... Deletes.one.character.backward
<<........................... Returns.to.the.previous
>>........................... Advances.to.the.next
OK........................... Executes.the.selection
CANCEL.................. Cancels.the.selection
(→.page.71)
101
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[WIRED]
Profiles (for LAN port [RJ-45]):
Up to two settings for the LAN port (RJ-45) can be stored in memory of the projector.
Select [PROFILE 1] or [PROFILE 2] and then do settings for [DHCP] and the other options.
After doing this, select [OK] and press the ENTER button. This will store your settings in memory.
To recall the settings from memory:
After selecting the [WIRED] tab, select the [PROFILE 1] or [PROFILE 2] from the [PROFILES] list.
Select [OK] and press the ENTER button.
DHCP:
Enabling this option automatically assigns an IP address to the projector from your DHCP server.
Disabling this option allows you to register the IP address or subnet mask number obtained from your network
administrator.
IP.ADDRESS........... Set.your.IP.address..Press. .to.display.the.software.keyboard.and.type.in.12.numeric.characters.
SUBNET.MASK....... Set.your.subnet.mask.number..Press
.
.to.display.the.software.keyboard.and.type.in.12.numeric.characters.
GATEWAy............... Set.the.default.gateway.of.the.network.connected.to.the.projector..Press. .to.display.the.software.keyboard.
and.type.in.12.numeric.characters.
DNS.CONFIGURATION... Type.in.the.IP.address.of.DNS.server.on.the.network.connected.to.the.projector..12.numeric.characters.
are.used.
RECONNECT........... Use.this.button.to.retry.to.connect.the.projector.to.a.network..Try.this.if.you.have.changed.[PROFILES].
10ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[WIRELESS]
PROFILES (for USB Wireless LAN unit):
To execute a wireless LAN easily using Image Express Utility 2.0, select [EASY CONNECTION].
Up to two settings for the USB wireless LAN unit can be stored in memory of the projector.
Select [PROFILE 1] or [PROFILE 2] and then do settings for [DHCP] and the other options.
After doing this, select [OK] and press the ENTER button. This will store your settings in memory.
To recall the settings from memory:
After selecting the [WIRELESS] tab, select the [PROFILE 1] or [PROFILE 2] from the [PROFILES] list.
Select [OK] and press the ENTER button.
DHCP:
Place a check mark to automatically assign an IP address to the projector from your DHCP server.
Clear this check box to register the IP address or subnet mask number obtained from your network administrator.
IP.ADDRESS........... Set.your.IP.address..Press. .to.display.the.software.keyboard.and.type.in.12.numeric.characters.
SUBNET.MASK....... Set.your.subnet.mask.number..Press. .to.display.the.software.keyboard.and.type.in.12.numeric.characters.
GATEWAy............... Set.the.default.gateway.of.the.network.connected.to.the.projector..Press. .to.display.the.software.keyboard.
and.type.in.12.numeric.characters.
DNS.CONFIGURATION... Type.in.the.IP.address.of.DNS.server.on.the.network.connected.to.the.projector..Twelve.numeric.charac-
ters.are.used.
ADVANCED............. Displays.the.Advanced.menu.which.includes.various.setting.for.wireless.LAN.connection.(NETWORK.
TyPE.and.SECURITy)..See.the.Advanced.menu.later.on.
RECONNECT........... Use.this.button.to.retry.to.connect.the.projector.to.a.network..Try.this.if.you.have.changed.[PROFILES].
NOTE: If you select [EASY CONNECTION] from [PROFILES], you cannot make settings to DHCP and its following items except
[CHANNEL] in [ADVANCED].
10ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[ADVANCED] menu
[CONNECTION] (required for wireless only)
SITE SURVEY:
Displays a list of available SSIDs for wireless LAN on site. Select an SSID which you can access.
To select an SSID, highlight [SSID] and use the SELECT to select [OK] and press the ENTER button.
: Wireless access point
: Ad Hoc PC
: WEP or WPA enabled
SSID (Network name):
Enter an identifier (SSID) for wireless LAN when selecting [INFRASTRUCTURE] or [AD HOC] in [NETWORK
TYPE]. Communication can be done only with equipment whose SSID matches SSID for your wireless LAN. Up
to 32 alphanumeric characters can be used (case sensitive).
NETWORK TYPE:
Select communication method when using wireless LAN.
INFRASTRUCTURE.. Select.this.option.when.communicating.with.one.or.more.equipment.connected.to.the.wireless.or.wired.
LAN.network.via.a.wireless.access.point.
AD.HOC.................. Select.this.option.when.using.the.wireless.LAN.to.directly.communicate.with.a.computer.in.peer-to-peer.
mode..This.is.a.method.that.meets.the.IEEE802.11.wireless.standard.
NOTE: When in Ad Hoc mode, only 802.11b is available for communication method.
Data transmission speed in Ad Hoc mode is limited up to 11Mbps.
CHANNEL:
Select a channel. Available channels vary depending on the country and region.
TIP: When you select [INFRASTRUCTURE], make sure that the projector and your access point are on the same channel;
when you select [AD HOC], make sure that the projector and your computer are on the same channel.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[SECURITY] (required for wireless only)
SECURITY TYpE
Select encryption mode for secure transmission.
When [WEP] or [DISABLE] is selected in [SECURITY TYPE]:
Select this option whether using the WEP (Wired Equivalent Privacy) key for encryption or not. To use encryp-
tion, specify WEP key.
DISABLE................. Will.not.turn.on.the.encryption.feature..your.communications.may.be.monitored.by.someone.
WEP(64BIT)............ Uses.64-bit.datalength.for.secure.transmission.
WEP(128BIT).......... Uses.128-bit.datalength.for.secure.transmission..This.option.will.increase.privacy.and.security.when.
compared.to.use.of.64-bit.datalength.encryption.
WPA-PSK................ Uses.WPA-PSK.encryption.mode.for.more.secure.transmission.than.WEP.
WPA2-PSK.............. Uses.WPA2-PSK.encryption.mode.for.more.secure.transmission.than.WPA.
NOTE:
• The WEP settings must be the same as communication devices such as PC or access point in your wireless network.
• When you use WEP, your image transmission speed will slow down.
• [WPA-PSK] and [WPA2-PSK] are not available when [AD HOC] is selected from [NETWORK TYPE].
KEY SELECT:
Selects one key from the four keys below when selecting [64BIT] or [128BIT] in [SECURITY TYPE].
KEY1-4:
Enter encryption key when selecting [64BIT] or [128BIT] in [SECURITY TYPE].
Up to 5 characters can be set in 64 bit, and up to 13 characters in 128 bit.
The key can also be set in hexadecimal digit.
Press the [HEX] button to change to [ASCII] to set the key in ASCII digit.You can toggle this button between [ASCII]
and [HEX].
* Enter 0x(numeral and alphabet respectively) right in front of your key code.
* Hexadecimal uses 0 to 9 and A to F.
* When setting in a hexadecimal digit, up to 10 characters can be set in 64 bit, and up to 26 characters in 128
bit.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Using Software Keyboard to enter an encryption key
1. Select one of [KEY 1], [KEY 2], [KEY 3] and [KEY 4] and press the ENTER button.
The software keyboard will be displayed.
2. Use the SELECT
button to select one key and press the ENTER button.
3. After finishing entering the WEP key, use the SELECT
TER button.
button to select [OK] and press the EN-
The software keyboard will disappear.
When [WPA-PSK] or [WPA2-PSK] is selected in [SECURITY TYPE]:
WPA-PSK................ Uses.WPA-PSK.encryption.mode.for.more.secure.transmission.than.WEP.
WPA2-PSK.............. Uses.WPA2-PSK.encryption.mode.for.more.secure.transmission.than.WPA.
* WPA-PSK (TKIP) provides stronger security than WEP where encryption keys are automatically changed, also
providing simple authentication, WPA, PSK and TKIP stand for Wi-Fi Protected Access, Pre-Shared Key and
Temporal Key Integrity Protocol respectively.
ENCRYPTION TYPE: Select [TKIP] or [AES].
KEY:
Enter encryption key when selecting [WPA-PSK] or [WPA2-PSK] is selected in [SECU-
RITY TYPE]. Key length must be eight or greater and 63 or less.
[DOmAIN]
HOST.NAME........... Type.in.a.hostname..Up.to.60.alphanumeric.characters.can.be.used.
DOMAIN.NAME....... Type.in.domain.name.of.the.network.connected.to.the.projector..Up.to.60.alphanumeric.characters.can.be.
used.
10ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[mAIL]
ALERT MAIL:
Checking this box enables Alert Mail feature.
This option notifies your computer of an error message via e-mail when using wireless or wired LAN. The error
message will be notified when the projector lamp has reached the end of its usable life or an error occurs in the
projector.
Sample of a message sent from the projector:
the lamp is at the end of its usable life. Please replace the lamp.
Projector name: X X X X
lamp hours Used: xxxx [h]
SENDER’S ADDRESS:
Specify the senders address. Use the Software keyboard. Up to 60 alphanumeric and symbols characters can
be used. See “Using Software Keyboard” in Appendix for more details.
SMTP SERVER NAME:
Type in the SMTP server name to be connected to the projector. Up to 60 alphanumeric characters can be used.
RECIPIENT’S ADDRESS 1 to 3:
Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.
TEST MAIL:
Send a test mail to check if your settings are correct.
NOTE:
• If you entered an incorrect address in a test, you may not receive an Alert mail. Should this happen, check if the Recipient’s
Address is correctly set.
• Unless any one of the [SENDER’S ADDRESS], [SMTP SERVER’S NAME] or [RECIPIENT’S ADDRESS 1-3] is selected, [TEST
MAIL] is not available.
• Be sure to highlight [OK] and press the ENTER button before executing [TEST MAIL].
NOTE: To use the Mail Alert feature on wireless LAN connection, select [INFRASTRUCTURE] for [NETWORK TYPE].
10ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Selecting Communication Speed [COmmUNICATION SpEED]
This feature sets the baud rate of the PC Control port (D-Sub 9 Pin). It supports data rates from 4800 to 38400 bps.
The default is 38400 bps. Select the appropriate baud rate for your equipment to be connected (depending on the
equipment, a lower baud rate may be recommended for long cable runs).
Your selected communication speed will not be affected even when [RESET] is done from the menu.
Turning On or Off Remote Sensor [REmOTE SENSOR]
This option determines which remote sensor on the projector is enabled in wireless mode.
The options are: front/back, front, and back.
Selecting power-saving in [STANDBY mODE]
The projector has two standby modes: [NORMAL] and [POWER-SAVING].
Power-saving mode is the mode that allows you to put the projector in the power-saving condition which consumes
less power than the Normal mode. The projector is preset for Normal mode at the factory.
NOTE:
• The HTTP server functions are not available during POWER-SAVING mode.
• The MONITOR OUT function is not available during POWER-SAVING mode.
• Control through the PC Control connector and LAN mode is not available during POWER-SAVING mode. For PC control and LAN
mode of the projector it is recommended to leave the projector in the Normal mode.
NORMAL.........................Power.indicator:.Orange.light/Status.indicator:.Green.light
POWER-SAVING.............Power.indicator:.Orange.light/Status.indicator:.Off
108
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[OPTIONS]
Setting Auto Adjust [AUTO ADJUST]
This feature sets the Auto Adjust mode so that the RGB image can be automatically or manually adjusted for noise
and stability.You can automatically make adjustment in two ways: [NORMAL] and [FINE].
OFF......................... The.RGB.image.will.not.be.automatically.adjusted.
you.can.manually.optimize.the.RGB.image.
NORMAL................. Default.setting..The.RGB.image.will.be.automatically.adjusted..Normally.select.this.option.
FINE........................ Select.this.option.if.fine.adjustment.is.needed..It.takes.more.time.to.switch.to.the.source.than.when.
[NORMAL].is.selected.
Enabling Auto Start [AUTO START]
Turns the projector on automatically when the power cable is inserted into an active power outlet and the main pow-
er switch is turned on. This eliminates the need to always use the POWER (ON/STANDBY) button on the remote
control or projector cabinet.
To use the Auto Start function, you must first press the main power switch to the position “On” before plugging the
power cable.
Enabling power management [pOWER mANAGEmENT]
When this option is selected you can enable the projector to automatically turn off (at the selected time: 5min.,
10min., 20min., 30min.) if there is no signal received by any input.
Enabling high Speed Fan mode [FAN mODE]
This option allows you to select two modes for fan speed: Auto mode, High speed mode, and High Altitude mode.
AUTO...................... The.built-in.fans.automatically.run.at.a.variable.speed.according.to.the.internal.temperature.
HIGH....................... The.built-in.fans.run.at.high.speed.
HIGH.ALTITUDE...... The.built-in.fans.run.at.a.high.speed..Select.this.option.when.using.the.projector.at.altitudes.approximate-
ly.5500.feet/1600.meters.or.higher.
When you wish to cool down the temperature inside the projector quickly, select [HIGH].
NOTE:
• It is recommended that you select High speed mode if you use the projector non-stop for consecutive days.
• Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH ALTITUDE] can cause
the projector to overheat and the protector could shut down. If this happens, wait a couple minutes and turn on the projector.
• Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTITUDE] can cause the
lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO].
• Your setting will not be affected even when [RESET] is done from the menu.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Selecting Default Source [DEFAULT SOURCE SELECT]
You can set the projector to default to any one of its inputs each time the projector is turned on.
LAST....................... Sets.the.projector.to.default.to.the.previous.or.last.active.input.each.time.the.projector.is.turned.on.
AUTO...................... Searches.for.an.active.source.in.order.of.COMPUTER1.→.COMPUTER2.→.COMPUTER3.→.COMPONENT.
→.VIDEO.→.S-VIDEO.→.VIEWER.→ COMPUTER1.and.displays.the.first.found.source.
COMPUTER.1......... Displays.the.RGB.source.from.the.COMPUTER.1.IN.connector.every.time.the.projector.is.started.up..
COMPUTER.2......... Displays.the.DVI.digital.source.from.the.COMPUTER.2.IN.connector.every.time.the.projector.is.started.
up.
COMPUTER.3......... Displays.the.RGB.source.from.the.COMPUTER.3(DVI-D).IN.connector.every.time.the.projector.is.started.
up..
COMPONENT.......... Displays.the.component.source.from.the.COMPONENT.IN.connector.every.time.the.projector.is.start.up.
VIDEO..................... Displays.the.Video.source.from.the.VIDEO.IN.connector.every.time.the.projector.is.started.up.
S-VIDEO................. Displays.the.Video.source.from.the.S-VIDEO.IN.connector.every.time.the.projector.is.started.up.
VIEWER.................. Displays.slides.from.the.USB.memory.device.every.time.the.projector.is.started.up.
NETWORK.............. Displays.a.signal.from.LAN.port.(RJ-45).or.the.USB.Wireless.LAN.Unit.
Selecting Signal Format [SIGNAL SELECT]
COMPUTER 1/2
Allows you to set [COMPUTER 1] and [COMPUTER 2] to automatically detect an incoming RGB or component
source such as a computer or DVD player. However there may be some RGB and component signals that the
projector is unable to detect. In this case, select [RGB] or [COMPONENT].
Selecting [COLOR SYSTEm]
This feature enables you to select video standards manually.
Normally select [AUTO]. Select the video standard from the pulldown menu. This must be done for Video and S-Vid-
eo Connector separately.
Setting mONITOR OUT Connector [OUT TERmINAL]
This option allows you to determine which RGB or component source is output from the MONITOR OUT connector
during Standby mode.
LAST....................... The.signal.from.the.last.COMPUTER.1,.COMPUTER.2.or.COMPONENT.input.will.be.output.to.the.MONI-
TOR.OUT.connector.
COMPUTER.1,.2..... The.signal.from.the.COMPUTER1.or.COMPUTER2.input.will.be.output.to.the.MONITOR.OUT.connector.
COMPONENT.......... The.signal.from.the.COMPONENT.input.will.be.output.to.the.MONITOR.OUT.connectors.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Menu Descriptions & Functions [INFO.]
Displays the lamp and the projector usage hours, the status of the current signal and settings, NETWORK settings
and version. The [INFO.] menu has eight pages.
The information included are as follows:
[USAGE TIME]
LAMP LIFE REMAINING (%)
LAMP HOURS USED (H)
FILTER HOURS USED (H)
NOTE: The progress indicator shows the percentage of remaining lamp life. The value informs you of the amount of lamp and fil-
ter usage respectively.
• When the remaining lamp time reaches 0, the Lamp Life Remaining bar indicator changes from 0% to 100 Hours and the
countdown starts.
If lamp life remaining time reaches 0 hours, the projector will not turn on regardless of whether the lamp mode is set to Normal
or Eco.
•
The message to the effect that the lamp should be replaced will be displayed for one minute when the projector is turned on or off.
To dismiss this message, press any button on the projector or the remote control.
Lamp Life
NORMAL
2000 Hours (Min.)
ECO
3000 Hours (Max.)
111
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[WIRED LAN]
This page shows information on settings for the LAN port (RJ-45)
IP.ADDRESS........... Indicates.the.IP.address.of.the.projector.when.the.LAN.port.(RJ-45).is.used.
SUBNET.MASK....... Indicates.the.subnet.mask.of.the.projector.when.the.LAN.port.(RJ-45).is.used.
GATEWAy............... Indicates.the.gateway.of.the.network.connected.to.the.projector.when.the.LAN.port.(RJ-45).is.used.
MAC.ADDRESS....... Indicates.the.MAC.address.of.the.LAN.port.(RJ-45)..
[WIRELESS LAN (1)]
This page shows information on settings for the USB Wireless LAN unit
IP.ADDRESS........... Indicates.the.IP.address.of.the.projector.when.the.USB.Wireless.LAN.unit.is.used.
SUBNET.MASK....... Indicates.the.subnet.mask.of.the.projector.when.the.USB.Wireless.LAN.unit.is.used.
GATEWAy............... Indicates.the.gateway.of.the.network.connected.to.the.projector.when.the.USB.Wireless.LAN.unit.is.used.
MAC.ADDRESS....... Indicates.the.MAC.address.of.the.USB.Wireless.LAN.unit.
11ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
[WIRELESS LAN (2)]
This page shows information on settings for WEP key for encryption.
SSID....................... Indicates.the.identifier.(SSID).for.your.wireless.LAN.
NETWORK.TyPE..... Indicates.that.[EASy.CONNECTION],.[INFRASTRUCTURE].or.[AD.HOC].is.selected.for.your.communica-
tion.method.
WEP/WPA............... Indicates.your.selected.datalength.encryption:.On.or.Off
CHANNEL............... Indicates.the.channel.you.selected.in.the.[SITE.SURVEy]..The.channel.must.match.for.all.wireless.devices.
communicating.on.your.wireless.LAN.
SIGNAL.LEVEL........ Indicates.receiving.condition.of.radio.signal.level.while.you.are.using.a.wireless.LAN.connection.. .
[VERSION (2)]
[VERSION (1)]
FIRMWARE
DATA
FIRMWARE2
DATA2
PRODUCT
SERIAL NUMBER
LAN UNIT TYPE
LAN UNIT VERSION
114
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using On-Screen Menu
Menu Descriptions & Functions [RESET]
Returning to Factory Default
The Reset feature allows you to change adjustments and settings to the factory preset for sources by the following
methods:
[CURRENT SIGNAL]
Resets the adjustments for the current signal to the factory preset levels.
All the items in [ADJUST] can be reset.
[ALL DATA]
Reset all the adjustments and settings for all the signals to the factory preset except [ENTRY LIST], [LANGUAGE],
[BACKGROUND], [FILTER MESSAGE], [SECURITY SETTINGS], [NETWORK SETTINGS], [COMMUNICATION
SPEED], [STANDBY MODE], [FAN MODE], [DATE, TIME PRESET], [LAMP LIFE REMAINING], [LAMP HOURS
USED] and [FILTER HOURS USED].
[ALL DATA (INCLUDING ENTRY LIST)]
Reset all the adjustments and settings for all the signals to the factory preset except [LANGUAGE], [BACK-
GROUND], [FILTER MESSAGE], [SECURITY SETTINGS], [NETWORK SETTINGS], [COMMUNICATION
SPEED], [STANDBY MODE], [FAN MODE], [DATE, TIME PRESET], [LAMP LIFE REMAINING], [LAMP HOURS
USED] and [FILTER HOURS USED].
Also deletes all the signals in the [ENTRY LIST] and returns to the factory preset.
NOTE: Locked signals in Entry List cannot be reset.
Clearing Lamp hour meter [CLEAR LAmp hOURS]
Resets the lamp clock back to zero.
NOTE: Elapsed time of the lamp use will not be affected even when [RESET] is done from the menu.
NOTE: The projector will turn off and go into standby mode when you continue to use the projector for another 100 hours after the
lamp has reached the end of its life. In this condition you cannot clear the lamp hour meter on the menu. If this happens, press the
HELP button on the remote control for 10 seconds to reset the lamp clock back to zero. Do this only after replacing the lamp.
Resetting the Filter Usage hours [CLEAR FILTER hOURS]
Resets the filter usage back to zero.
NOTE: Elapsed time of the filter use will not be affected even when [RESET] is done from the menu.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Maintenance
This section describes the simple maintenance procedures you should follow to clean the filters and replace the lamp.
Cleaning or Replacing the Filter
The air-filter sponge keeps dust and dirt from getting inside the projector and should be frequently cleaned. If the
filter is dirty or clogged, your projector may overheat.
NOTE: The message for filter cleaning will be displayed for one minute when the projector is turned on or off.
To cancel the message, press any button on the projector cabinet or the remote control.
CAUTION
•
•
•
Turn off the projector, turn off the main power switch and unplug the projector before replacing the filter.
Only clean the outside of the filter cover with a vacuum cleaner.
Do not attempt to operate the projector without the filter cover.
To clean the air-filter:
Vacuum the filter-through the filter cover.
S E L E C T
P
U
N
D O W
T
H
G
I
R
T
F I
H
S
S
T
F
N
E
E
L
L
filter
To reset the filter usage time, from the menu, select [RESET]
[CLEAR FILTER HOURS].
→
(
→
page 115 for resetting the filter usage time)
To replace the filter (sponge):
CAUTION
•
•
•
•
•
Replace both filters at the same time.
Before replacing the filters, remove dust and dirt from the projector cabinet.
The projector contains high-precision parts. Keep out dust and dirt during filter replacement.
Do not wash the filter with water. Water will damage the filter membrane.
Reattach the filter cover correctly. Failure to do so may cause projector malfunction.
preparation: Replace the lamp before replacing the filters.
NOTE: When you replace the lamp, it is also wise to replace the filter. The filter comes in the same package with your replacement lamp.
1. Pull to remove the filter cover.
11ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Maintenance
2. Gently peel off the filter (sponge) and replace it with the new one.
The filter is attached self-adhesive tape. Peel off a release paper before use.
3. Reinstall the new filter cover.
•
Slip the filter cover back until it snaps into place.
4. Connect the supplied power cable, turn on the Main Power switch and turn on the projector.
5. Finally, select the menu [RESET] [CLEAR FILTER HOURS] to reset the filter usage hours.
→
→
(
page 115 for resetting the filter usage time)
→
Cleaning the Cabinet and the Lens
1. Turn off the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong
detergents or solvents such as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.
R
L
L
E
E
E
S
W
F
N
U
O
P
T
S
T
S
A
T
H
P
IF
S
T
M
A
L
B
S
U
D
B Y
R
IG
H
T
O N / S T A N
C E
S O U R
A D J U S T
A U T O
D
O
W
N
M
R E F O R
3 D
U
P
S
E
L
E
C
T
T
C
E
L
E
S
P
U
3
D
N
R
E
F
D O W
ORM
AUT
O
A
D
J
U
ST
S
OUR
CE
O
N
/
S
T
A
N
U
S
D
B
B
L
A
Y
M
S
P
T
A
T
P
U
S
O
T
W
H
G
E
I
R
R
S
T
F I
H
S
S
T
F
N
E
E
L
L
S
WIRLES
11ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Maintenance
Replacing the Lamp
When the lamp reaches the end of its life, the LAMP indicator in the cabinet will blink red. Even though the lamp
may still be working, replace the lamp to maintain the optimal projector performance. After replacing the lamp, be
sure to clear the lamp hour meter. ( page 115)
→
CAUTION
•
DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off,
wait 30 seconds, turn off the main power switch and then disconnect the power cable. Allow at least one hour for
the lamp to cool before handling.
•
•
DO NOT REMOVE ANY SCREWS except two lamp housing screws.You could receive an electric shock.
Do not break the glass on the lamp housing.
Keep finger prints off the glass surface on the lamp housing. Leaving finger prints on the glass surface might
cause an unwanted shadow and poor picture quality.
•
The projector will turn off and go into standby mode when you continue to use the projector for another 100 hours
after the lamp has reached the end of its life. If this happens, be sure to replace the lamp. If you continue to use the
lamp after the lamp reaches the end of its life, the lamp bulb may shatter, and pieces of glass may be scattered in
the lamp case. Do not touch them as the pieces of glass may cause injury. If this happens, contact your NEC dealer
for lamp replacement.
To replace the lamp:
Optional lamp and tools needed for replacement:
•
•
Replacement lamp NP06LP
Phillips screwdriver or equivalent
1. Use a Philips screwdriver to push and release the tab.
Push and pull to remove the lamp cover.
O
N
/S
T
A
N
U
S
D
B
B
L
A
Y
M
S
P
T
A
T
P
U
S
O
W
E
R
2
1
118
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Maintenance
2. Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling
condition.The two screws are not removable.
Remove the lamp housing by holding it.
interlock
NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.
3. Insert a new lamp housing until the lamp housing is plugged into the socket.
CAUTION
Do not use a lamp other than the NEC replacement lamp NP06LP.
Order this from your NEC dealer.
Secure it in place with the two screws.
Be sure to tighten the screws.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Maintenance
4. Reattach the lamp cover.
Slip the lamp cover back until it snaps into place.
ON/STA
USB
BY
L
A
STATUS
M
P
POWER
E
O
N
/S
T
A
N
U
SB
D
B
L
A
Y
M
S
P
T
A
P
T
U
O
S
W
E
R
1
2
5. Connect the supplied power cable, turn on the Main Power switch and turn on the projector.
6. Finally, select the menu
usage hours.
[RESET]
[CLEAR LAMP HOURS] to reset the lamp life remaining and lamp
→
→
NOTE: When you continue to use the projector for another 100 hours after the lamp has reached the end of its life, the projector
cannot turn on and the menu is not displayed.
If this happens, press the HELP button on the remote control for 10 seconds to reset the lamp clock back to zero.
When the lamp time clock is reset to zero, the LAMP indicator goes out.
1ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Using Optional Lenses
Five optional lenses are available for the NP3150/NP2150/NP1150. See the information described on this page to
buy the appropriate lens for your screen size and throw distance. See page 123 for installing the lens.
Table of Throw Distances and Screen Sizes for Optional Lenses
Screen
STANDARD
NP01FL
NP02ZL
NP03ZL
NP04ZL
NP05ZL
Size
1.5 − 2.0
0.8
1.2 − 1.5
1.9 − 3.1
3.0 − 4.8
4.7 − 7.2
(m)
(inches)
(m)
(inches)
(m)
0.70 – 0.92 27.5 – 36.4
0.95 – 1.25 37.3 – 49.1 1.56 – 2.51 61.4 – 98.6
(inches)
(m)
(inches)
(m)
(inches)
(m)
(inches)
30"
40"
60"
67"
72"
80"
84"
90"
100"
120"
150"
180"
200"
210"
240"
250"
270"
300"
0.89 – 1.20 35.1 – 47.3
1.20 – 1.62 47.4 – 63.8 0.64
1.83 – 2.45 72.2 – 96.6 0.98
2.05 – 2.75 80.8 – 108.2 1.10
2.21 – 2.96 87.0 – 116.4 1.18
2.46 – 3.29 96.9 – 129.5 1.32
2.59 – 3.46 101.8 – 136.1 1.39
2.78 – 3.71 109.3 – 146.0 1.49
3.09 – 4.13 121.6 – 162.4 1.66
3.72 – 4.96 146.3 – 195.3 2.00
4.66 – 6.21 183.4 – 244.6 2.50
5.60 – 7.47 220.5 – 294.0
6.23 – 8.30 245.3 – 326.9
6.54 – 8.72 257.6 – 343.3
7.49 – 9.97 294.7 – 392.6
7.80 – 10.39 307.1 – 409.1
8.43 – 11.23 331.8 – 442.0
9.37 – 12.48 368.9 – 491.3
25.3
38.6
43.3
46.6
51.9
54.6
58.6
65.3
78.6
98.6
1.44 – 1.89 56.9 – 74.5 2.37 – 3.79 93.5 – 149.4 3.60 – 5.83 141.7 – 229.7 5.69 – 8.75 224.1 – 344.6
1.62 – 2.12 63.7 – 83.4 2.66 – 4.25 104.7 – 167.1 4.03 – 6.53 158.8 – 257.0 6.38 – 9.80 251.1 – 385.7
1.74 – 2.28 68.6 – 89.8 2.86 – 4.57 112.8 – 179.8 4.34 – 7.03 171.1 – 276.6 6.87 – 10.54 270.4 – 415.0
1.94 – 2.54 76.4 – 99.9 3.19 – 5.08 125.6 – 200.1 4.84 – 7.82 190.6 – 307.9 7.65 – 11.73 301.3 – 462.0
2.04 – 2.67 80.3 – 105.0 3.35 – 5.34 132.0 – 210.3 5.09 – 8.22 200.4 – 323.5 8.05 – 12.33 316.8 – 485.5
2.19 – 2.86 86.2 – 112.6 3.60 – 5.73 141.7 – 225.5 5.46 – 8.81 215.0 – 346.9 8.63 – 13.23 340.0 – 520.7
2.44 – 3.18 96.0 – 125.4 4.01 – 6.37 157.7 – 250.8 6.08 – 9.81 239.5 – 386.0 9.62 – 14.72 378.6 – 579.4
2.93 – 3.83 115.5 – 150.8 4.82 – 7.66 189.8 – 301.6 7.32 – 11.79 288.3 – 464.2 11.58 – 17.70 455.8 – 696.8
3.68 – 4.80 144.9 – 188.9 6.05 – 9.59 238.0 – 377.7 9.18 – 14.77 361.6 – 581.5 14.52 – 22.17 571.7 – 872.9
4.42 – 5.77 174.2 – 227.1 7.27 – 11.53 286.2 – 453.8 11.05 – 17.75 434.9 – 698.7 17.46 – 26.65 687.5 –1049.0
4.92 – 6.41 193.8 – 252.5 8.08 – 12.81 318.3 – 504.5 12.29 – 19.73 483.8 – 776.9 19.43 – 29.63 764.8 –1166.4
5.17 – 6.74 203.5 – 265.2 8.49 – 13.46 334.3 – 529.9 12.91 – 20.73 508.2 – 816.0 20.41 – 31.12 803.4 –1225.1
5.91 – 7.71 232.9 – 303.4 9.72 – 15.39 382.5 – 606.0 14.77 – 23.70 581.5 – 933.3 23.35 – 35.59 919.3 –1401.2
6.16 – 8.03 242.7 – 316.1 10.12 – 16.04 398.6 – 631.4 15.39 – 24.70 605.9 – 972.4 24.33 – 37.08 957.9 –1459.9
6.66 – 8.67 262.2 – 341.5 10.94 – 17.33 430.7 – 682.1 16.63 – 26.68 654.8 –1050.5 26.29 – 40.06 1035.1–1577.3
7.41 – 9.64 291.5 – 379.7 12.16 – 19.26 478.8 – 758.2 18.49 – 29.66 728.1 –1167.8 29.23 – 44.54 1151.0–1753.5
9.89 – 12.87 389.3 – 506.8 16.24 – 25.70 639.4 –1011.9 24.70 – 39.59 972.4 –1558.7 39.04 – 59.45 1537.2–2340.5
12.37 – 16.10 487.1 – 634.0 20.32 – 32.15 799.9 –1265.6 30.90 – 49.52 1216.7–1949.5 48.85 – 74.36 1923.4–2927.5
400" 12.51 – 16.66 492.5 – 655.8
500" 15.65 – 20.83 616.2 – 820.2
For screen sizes between 30" and 500" not indicated on the above table, use formulas below.
Throw distance for Standard lens (m/inch)=H 1.5 through H 2.0 Distance from 0.89m to 20.83m/35.1" to 820.2"
×
×
Throw distance for NP01FL(m/inch)=H 0.8 Distance from 0.64m to 2.5m/25.3" to 98.6"
×
Throw distance for NP02ZL(m/inch)=H 1.2 through H 1.5 Distance from 0.7m to 16.1m/27.5" to 634"
Throw distance for NP03ZL(m/inch)=H 1.9 through H 3.1 Distance from 1.56m to 32.15m/61.4" to 1265.6"
Throw distance for NP04ZL(m/inch)=H 3.0 through H 4.8 Distance from 3.6m to 49.52m/141.7" to 1949.5"
Throw distance for NP05ZL(m/inch)=H 4.7 through H 7.2 Distance from 5.69m to 74.36m/224.1" to 2927.5"
×
×
×
×
×
×
×
×
“H”= Screen width
NP04ZL (H X 3.0) - (H X 4.8)
STANDARD (H X 1.5) - (H X 2.0)
NP01FL (H X 0.8)
NP02ZL (H X 1.2) - (H X 1.5)
NP03ZL (H X 1.9) - (H X 3.1)
NP05ZL (H X 4.7) - (H X 7.2)
Example: Distance from a 100" screen with the lens Np0ꢁZL
Referring to the diagram on page 134, “H” is 2.0 m/78.7". Therefore, the projection distances of 100 inches are from
2.0 m/78.7" 1.9 to 2.0 m/78.7" 3.1 = from 3.8 m/150" to 6.2 m/244".
×
×
NOTE: Distances may vary +/-5%
1ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Using Optional Lenses
Lens Shift Adjustable Range
The top right diagram shows the location of the image position in the lens. The lens can be shifted within the shad-
ed area as shown using the normal projection position as a starting point.
The projector has a lens shift feature that allows you to move the image vertically or horizontally.
Desktop front projection
0.5V
Vertical shift
Max. 0.5V
1V
Height of projected image
0.1H
1H
0.1H
Nomal projection position
Width of projected image
Ceiling front projection
Shift to left
Shift to right
Max.
0.5V
Vertical shift
1V
1ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Using Optional Lenses
Replacing with Optional Lens
CAUTION
•
•
•
Do not give a shock or excessive load to the projector or the lens components as the projector and lens compo-
nents contain precision parts.
When shipping the projector with the optional lens, remove the optional lens before shipping the projector. The
lens and the lens shift mechanism may encounter damage caused by improper handling during transportation.
Before removing or installing the lens, be sure to turn off the projector, wait until the cooling fans stop, and turn
off the main power switch.
•
•
•
•
•
Do not touch the lens surface when removing or installing the lens.
Keep fingerprints, dust or oil off the lens surface. Do not scratch the lens surface.
Work on a level surface with a soft cloth under it to avoid scratching.
If you remove and store the lens, attach the lens cap to the projector to keep off dust and dirt.
Please heed the following information if you own two or more NP3150/NP2150/NP1150 projectors and may in-
terchange the standard lenses.
When replacing the standard lens (with an optional lens) and then re-installing the standard lens back into the
projector, the standard lens must go back to its original projector from which it was removed.
If you remove the standard lens from one NP3150/NP2150/NP1150 projector and re-install it into another
NP3150/NP2150/NP1150 projector, performance may be compromised.
Be sure to use the standard lens in combination with its original factory-adjusted projector.
lens release
Button
Remove the existing lens from the projector.
T
C
E
L
E
S
P
U
1. Rotate the lens counterclockwise while strongly pushing the
LENS RELEASE button all the way in.
N
W
O
D
T
R I G H
L E F T
The existing lens will be disengaged.
NOTE: If the lens cannot be removed even by using the LENS RELEASE but-
ton, the anti-theft screw for lens may be used to secure the lens.
If such is the case, remove the anti-theft screw first. (→ page 124)
2. Pull out the existing lens slowly.
T
C
E
L
E
S
P
U
N
W
O
D
T
R I G H
L E F T
1ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Using Optional Lenses
Install the new lens
1. Insert the lens with the yellow protrusion on top.
T
R I G H
L E F T
Yellow
Protrusion
2. Rotate the lens clockwise.
T
C
E
L
E
P
S
U
N
W
O
D
Rotate the lens until you feel it click into place.
T
R I G H
L E F T
Using the anti-theft screw to prevent theft of the lens
Tighten the supplied anti-theft screw on the front bottom.
hole of anti-theft screw for lens unit
1ꢀ4
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
Indicator Condition
projector Condition
The.main.power.is.off
The.projector.is.getting.ready.to.turn.on. Wait.for.a.moment.
Note
Off
–
Blinking.light
Green
0.5.sec.On,
0.5.sec.Off
2.5.sec.On,
0.5.sec.Off
0.5.sec.On,
0.5.sec.Off
Off.Timer.(Off.Time).is.activated.
–
Orange
The.projector.is.cooling.down.
Wait.for.a.moment.
Steady.light
Green
Orange
The.projector.is.turned.on.
The.projector.is.in.Standby.
–
–
Status Indicator
Indicator Condition
Off
projector Condition
Note
Normal
–
Blinking.light
Red
1.cycle.(0.5.sec.On,. Lamp.cover.error
2.5.sec.Off)
Reattach.the.lamp.cover.correctly.
(→.page.120)
2.cycle.(0.5.sec.On,. Temperature.error
0.5.sec.Of)
4.cycle.(0.5.sec.On,. Fan.error
0.5.sec.Off)
The.projector.is.overheated..Move.
the.projector.to.a.cooler.location.
Fans.will.not.work.correctly.
6.cycle.(0.5.sec.On,. Lamp.error
0.5.sec.Off)
Lamp.fails.to.light..Wait.a.full.
minute.and.then.turn.on.again.
The.projector.is.re-firing.
Green
Re-firing.the.lamp
Orange
1.cycle.(0.5.sec.On,. Network.conflict.
Both.the.built-in.wired.LAN.and.the.
wireless.LAN.cannot.be.connected.to.
the.same.network.at.the.same.time.
To.use.both.built-in.wired.LAN.and.
wireless.LAN.at.the.same.time,.con-
nect.them.to.different.networks.
(→.page.102,.103)
.
.
.
.
.
.
2.5.sec.Off)
.
.
.
.
.
.
.
.
.
Steady.light
Orange
Control.Panel.Lock.is.on
you.have.pressed.cabinet.button.
when.Control.Panel.Lock.is.on.
(→.page.94)
Green
The.projector.is.in.Standby.
–
Lamp Indicator
Indicator Condition
projector Condition
Note
Off
Normal
–
Lamp.has.reached.its.end.of.life..Lamp. Replace.the.lamp.
replacement.message.will.be.displayed. (→.page.118)
Lamp.has.been.used.beyond.its.limit.. Replace.the.lamp.
The.projector.will.not.turn.on.until.the. (→.page.118)
lamp.is.replaced.
Red
Blinking.light
Red
Steady.light
Lamp.is.in.Eco.mode
–
Green
Over-Temperature protection
If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp with the
STATUS indicator blinking (2-cycle On and Off.)
Should this happen, do the following:
• Unplug the power cable after the cooling fans stop.
• Move the projector to a cooler location if the room where you are presenting is particularly too warm.
• Clean the ventilation holes if they are clogged with dust.
• Wait about 60 minutes until the inside of the projector becomes cool enough.
1ꢀ5
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
Common Problems & Solutions ( “Power/Status/Lamp Indicator” on page 125)
→
problem
Check These Items
Does.not.turn.on
•. Check.that.the.power.cable.is.plugged.in.and.that.the.power.button.on.the.projector.cabinet.or.the.remote.
control.is.on..(→.page.21,.22)
•. Ensure.that.the.lamp.cover.is.installed.correctly..(→.page.120)
•. Check.to.see.if.the.projector.has.overheated..If.there.is.insufficient.ventilation.around.the.projector.or.if.the.
room.where.you.are.presenting.is.particularly.warm,.move.the.projector.to.a.cooler.location.
•. Check.to.see.if.you.continue.to.use.the.projector.for.another.100.hours.after.the.lamp.has.reached.the.end.
of.its.life..If.so,.replace.the.lamp.
.
After.replacing.the.lamp,.reset.the.lamp.hours.used..(→.page.115)
•. The.lamp.may.fail.to.light..Wait.a.full.minute.and.then.turn.on.the.power.again.
•.. Set.[FAN.MODE].to.[HIGH.ALTITUDE].when.using.the.projector.at.altitudes.approximately.5500.feet/1600.
meters.or.higher..Using.the.projector.at.altitudes.approximately.5500.feet/1600.meters.or.higher.without.
setting.to.[HIGH.ALTITUDE].can.cause.the.projector.to.overheat.and.the.projector.could.shut.down..If.this.
happens,.wait.a.couple.minutes.and.turn.on.the.projector..(→.page.109)
.
Also.when.the.lamp.is.turned.off,.the.projector.internal.temperature.is.hot..If.the.power.is.turned.on.before.
the.projector.has.cooled.down,.the.fan.will.run.a.short.time.before.the.lamp.will.turn.on.
Will.turn.off
No.picture
•. Ensure.that.the.Power.Management,.Off.Timer.is.off..(→.page.89,.109)
•. Use.the.SOURCE.button.on.the.projector.cabinet.or.the.VIDEO,.the.S-VIDEO,.the.COMPUTER.1,.the.COM-
PUTER.2,.the.COMPUTER.3,.the.COMPONENT,.the.VIEWER.or.the.NETWORK.button.on.the.remote.control.
to.select.your.source..(→.page.24)
•. Ensure.your.cables.are.connected.properly.
•. Use.menus.to.adjust.the.brightness.and.contrast..(→.page.80)
•. Check.to.see.if.the.image.is.muted..(→.page.34)
•. Remove.the.lens.cap.
•. Reset.the.settings.or.adjustments.to.factory.preset.levels.using.the.Reset.in.the.Menu..(→.page.115)
•. Enter.your.registered.keyword.if.the.Security.function.is.enabled..(→.page.44)
•. Be.sure.to.connect.the.projector.and.notebook.PC.while.the.projector.is.in.standby.mode.and.before.turn-
ing.on.the.power.to.the.notebook.PC.
.
In.most.cases.the.output.signal.from.the.notebook.PC.is.not.turned.on.unless.connected.to.the.projector.
before.being.powered.up.
*. If.the.screen.goes.blank.while.using.your.remote.control,.it.may.be.the.result.of.the.computer’s.screen-
saver.or.power.management.software.
•. See.also.the.next.page.
Color.tone.or.hue.is.
unusual
•. Check.if.an.appropriate.color.is.selected.in.[WALL.COLOR]..If.not,.select.an.appropriate.option..(→.page.88)
•. Adjust.[HUE].in.[ADJUST]..(→.page.80)
Image.isn’t.square.to.
the.screen
•. Reposition.the.projector.to.improve.its.angle.to.the.screen..(→.page.25)
•. Use.the.3DReform.function.to.correct.the.trapezoid.distortion..(→.page.29)
Picture.is.blurred
•. Adjust.the.focus..(→.page.27)
•. Reposition.the.projector.to.improve.its.angle.to.the.screen..(→.page.25)
•. Ensure.that.the.distance.between.the.projector.and.screen.is.within.the.adjustment.range.of.the.lens..(→.
page.121,.122)
•. Condensation.may.form.on.the.lens.if.the.projector.is.cold,.brought.into.a.warm.place.and.is.then.turned.
on..Should.this.happen,.let.the.projector.stand.until.there.is.no.condensation.on.the.lens.
Flicker.appears.on.
screen
•.. Set.[FAN.MODE].to.other.than.[HIGH.ALTITUDE].mode.when.using.the.projector.at.altitudes.approximately.
5500.feet/1600.meters.or.lower..Using.the.projector.at.altitudes.less.than.approximately.5500.feet/1600.
meters.and.setting.to.[HIGH.ALTITUDE].can.cause.the.lamp.to.overcool,.causing.the.image.to.flicker..
Switch.[FAN.MODE].to.[AUTO]..(→.page.109)
Image.is.scrolling.
vertically,.horizontally.or.
both
•. Use.the.SOURCE.button.on.the.projector.cabinet.or.the.VIDEO,.the.S-VIDEO,.the.COMPUTER.1,.the.COM-
PUTER.2,.the.COMPUTER.3,.the.COMPONENT,.the.VIEWER.or.the.NETWORK.button.on.the.remote.control.
to.select.your.source.(Video,.S-Video,.Computer,.Component,.Viewer.or.NETWORK)..(→.page.24)
•. Adjust.the.computer.image.manually.with.the.[CLOCK]/[PHASE].in.[ADJUST].→.[IMAGE.OPTIONS]..(→.page.81)
Remote.control.does.
not.work
•. Install.new.batteries..(→.page.10)
•. Make.sure.there.are.no.obstacles.between.you.and.the.projector.
•. Stand.within.22.feet.(7.m).of.the.projector..(→.page.10)
•. Check.if.one.or.more.remote.sensors.are.enabled..Select.[SETUP].→.[INSTALLATION].→.[REMOTE.SEN-
SOR].from.the.menu..See.page.108.
•. If.the.remote.control.cable.plug.is.inserted.into.the.REMOTE.mini.jack,.the.remote.control.does.not.function.
wirelessly..See.page.11.
Indicator.is.lit.or.blink-
ing
•. See.the.POWER/STATUS/LAMP.Indicator..(→.page.125)
Vertical.stripes.in.RGB.
mode
•. Press.the.AUTO.ADJUST.button.on.the.projector.cabinet.or.the.AUTO.ADJ..button.on.the.remote.control..(→.
page.31)
•. Adjust.the.computer.image.manually.with.the.[CLOCK]/[PHASE].in.[ADJUST].→.[IMAGE.OPTIONS]..(→.page.81)
USB.mouse.does.not.
work
•. Make.sure.that.your.USB.mouse.is.properly.connected.to.the.projector..(→.page.36)
.
The.projector.may.not.support.some.brands.of.a.USB.mouse.
•. Some.menu.items.cannot.be.operated.with.a.USB.mouse.
For more information contact your dealer.
1ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
If there is no picture, or the picture is not displayed correctly.
•
Power on process for the projector and the PC.
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on
the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before
being powered up.
NOTE: You can check the horizontal frequency of the current signal in the projector’s menu [SOURCE(2)] under Information.
If it reads “0kHz”, this means there is no signal being output from the computer. See page 112 or go to next step.
•
Enabling the computer’s external display.
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projec-
tor. When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come
on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle
through external display selections.
•
•
Non-standard signal output from the computer
If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed
correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use.
Each notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the previ-
ous step. Refer to your computer’s documentation for detailed information.
Image displayed is incorrect when using a Macintosh
When using a Macintosh with the projector, set the DIP switch of the Mac adapter (not supplied with the projec-
tor) according to your resolution. After setting, restart your Macintosh for the changes to take affect.
For setting display modes other than those supported by your Macintosh and the projector, changing the DIP
switch on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP
switch to the 13” fixed mode and then restart your Macintosh. After that, restore the DIP switches to a display-
able mode and then restart the Macintosh again.
NOTE: A Video Adapter cable manufactured by Apple Inc. is needed for a PowerBook which does not have a mini D-Sub
15-pin connector.
•
•
Mirroring on a PowerBook
* When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless “mirroring”
is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.
Folders or icons are hidden on the Macintosh screen
Folders or icons may not be seen on the screen. Should this happen, select [View]
menu and arrange icons.
[Arrange] from the Apple
→
1ꢀꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
Specifications
This section provides technical information about the projector’s performance.
Model Number
NP3150/NP2150/NP1150
Optical
LCD Panel
0.8" p-Si TFT active-matrix with Micro Lens Array (Aspect ratio 4:3)
Resolution
1024
768 pixels* up to UXGA with scaling technology (up to 1400
1050 @ 60 Hz on DVI-D)
Standard Lens
Lamp
Manual zoom and focus:
F1.7 - 2.2 f=24.4 - 32.5 mm
NP3150 : 330W AC (264 W in Eco mode)
NP2150/NP1150 : 300W AC (264W in Eco mode)
NP3150 : 5000 lumens (approx.80% in Eco)
NP2150 : 4200 lumens (approx.88% in Eco)
NP1150 : 3700 lumens (approx.88% in Eco)
Light Output
Contrast Ratio(full white: full black) 600:1
Image Size (Standard lens)
Lens Options
30" - 500" (0.76 m - 12.7 m) diagonal
Fixed lens : NP01FL (throw ratio 0.8:1)
Zoom lens : NP02ZL (throw ratio 1.2-1.5:1)
NP03ZL (throw ratio 1.9-3.1:1)
NP04ZL (throw ratio 3.0-4.8:1)
NP05ZL (throw ratio 4.7-7.2:1)
Lens Shift : Vertical +/- 0.5V, Horizontal +/- 0.1H
Electrical
Inputs
1 Analog RGB (Mini D-Sub 15 P), 1 Analog RGB R/Cr, G/Y, B/Cb, H, V
(BNC
(RCA
5), 1 Digital RGB (DVI-D 24 P), 1 Component Y, Cb/Pb, Cr/Pr
3), 1 Component (Mini D-Sub 15 P) shared with COMPUTER
1 IN, 1 S-Video (Mini DIN 4P), 1 Video, 3 Stereo Mini Audio, 2 (L/R)
RCA Audio, 1 Remote Control (Stereo Mini)
1 RGB (Mini D-Sub 15P), 1 Stereo Mini Audio
1 PC Control Port (D-Sub 9P)
Outputs
PC Control
USB Port
LAN Port
Wireless LAN
Video Compatibility
1 A Type
RJ-45
USB
NTSC, NTSC4.43, PAL, PAL60, PAL-N, PAL-M, SECAM,
DTV: 480i, 480p, 720p, 1080i (60Hz)
576i, 576p, 1080i (50Hz)
DVD: Progressive (50/60Hz)
Horizontal: 15 kHz to 108 kHz (RGB: 24 kHz or over)
Vertical: 48 Hz to 120 Hz
RGB: 165MHz (Maximum sampling rate)
16.7 million colors simultaneously, Full color
NTSC / NTSC4.43 / PAL / PAL-M / PAL-N / PAL60: 540 TV lines
SECAM: 300 TV lines
Scan Rate
Video Bandwidth
Color Reproduction
Horizontal Resolution
RGB: 1024 dots (H)
768 dots (V)
External Control
Sync Compatibility
Built-in Speakers
Power Requirement
Input Current
RS232, IR, LAN, USB
Separate Sync / Composite Sync / Sync on G
5W
2
100 - 240V AC, 50/60Hz
NP3150 : 5.9 - 2.3A
NP2150/NP1150 : 5.5 - 2.2A
Power Consumption
NP3150 : 490W in Lamp Normal mode
NP2150/NP1150 : 460W in Lamp Normal mode
NP3150/NP2150/NP1150: 410W in Lamp Eco mode/26W in Standby/
5W in Power-saving
* Effective pixels are more than 99.99%.
1ꢀ8
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
mechanical
Installation
Dimensions
Orientation: Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
15.7" (W)
5.9" (H)
14.1" (D)
399 mm (W)
150.5 mm (H)
358 mm (D)
(not including protrusions)
Weight
16.1 lbs/7.3 kg
Environmental Considerations
Operational Temperatures :
41° to 104°F / 5° to 40°C,
(Eco mode selected automatically at 95° to 104°F/35° to 40°C), 20% to
80% humidity (non-condensing)
Storage Temperatures :
Regulations
14° to 122°F (-10° to 50°C), 20% to 80% humidity
(non-condensing)
UL/C-UL Approved (UL 60950-1, CSA 60950-1)
Meets DOC Canada Class B requirements
Meets FCC Class B requirements
Meets AS/NZS CISPR.22 Class B
Meets EMC Directive (EN55022, EN55024, EN61000-3-2,
EN61000-3-3)
Meets Low Voltage Directive (EN60950-1, TÜV GS Approved)
For additional information visit:
US : http://www.necdisplay.com/
Europe : http://www.nec-display-solutions.com/
Global : http://www.nec-pj.com/
For information on our optional accessories, visit our website or see our brochure.
The specifications are subject to change without notice.
USB Wireless LAN Unit
For United States, Canada, and Mexico
Product Name
Operating Voltage
MAX Amps
NP01LM3
5V (power supplied from the projector)
Tx: 472 mA(Max)
Rx: 300 mA(Max)
Wireless Standard
Modulation Method
LED Display (Blue)
IEEE802.11a, IEEE802.11b, IEEE802.11g
CCK/DQPSK/DBPSK/OFDM
During communication: blinking
Standby: slow blinking
No operation: light off
IEEE802.11a
Center Frequency Range/
Operating channels
5150 to 5350, 5725 to 5850 MHz
36,40,44,48,52,56,60,64,149,153,157,161,165 channels
OFDM method (Orthogonal Frequency Division Multiplexing method)
54/48/36/24/18/12/9/6 (Mbps)
Transmission method
Data Rates
IEEE802.11b
Center Frequency Range/
Operating channels
2412 to 2462 MHz
1 to 11 channels
Transmission method
Data Rates
DS-SS method (direct dispersion spectrum dispersion method)
11/5.5/2/1 (Mbps)
1ꢀ9
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
IEEE802.11g
Center Frequency Range/
Operating channels
2412 to 2462 MHz
1 to 11 channels
Transmission method
Data Rates
OFDM method (Orthogonal Frequency Division Multiplexing method)
54/48/36/24/18/12/9/6 (Mbps)
Interface
USB 2.0 (connected to USB wireless LAN port on the projector)
Dimensions
Width:1.1"/28 mm
Height:0.43"/11 mm
Length:3.03"/77 mm
0.042 lbs/19 g
Weight
Environmental Considerations Operational Temperatures :
41° to 104°F / 5° to 40°C, 20% to 80% humidity (non-condensing)
Storage Temperatures :
14° to 122°F (-10° to 50°C), 20% to 80% humidity (non-condensing)
For other countries except United States, Canada and Mexico
Product Name
Operating Voltage
MAX Amps
NP01LM2
5V (power supplied from the projector)
Tx: 472 mA(Max)
Rx: 300 mA(Max)
Wireless Standard
Modulation Method
LED Display (Blue)
IEEE802.11a, IEEE802.11b, IEEE802.11g
CCK/DQPSK/DBPSK/OFDM
During communication: blinking
Standby: slow blinking
No operation: light off
IEEE802.11a
Center Frequency Range/
Operating channels
5150 to 5250, 5250 to 5350, 5470 to 5725 MHz
36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128,
132, 136, 140 channels
Transmission method
Data Rates
OFDM method (Orthogonal Frequency Division Multiplexing method)
54/48/36/24/18/12/9/6 (Mbps)
IEEE802.11b
Center Frequency Range/
Operating channels
2412 to 2472 MHz
1 to 13 channels
Transmission method
Data Rates
DS-SS method (direct dispersion spectrum dispersion method)
11/5.5/2/1 (Mbps)
IEEE802.11g
Center Frequency Range/
Operating channels
2412 to 2472 MHz
1 to 13 channels
Transmission method
Data Rates
OFDM method (Orthogonal Frequency Division Multiplexing method)
54/48/36/24/18/12/9/6 (Mbps)
Interface
USB 2.0 (connected to USB wireless LAN port on the projector)
Dimensions
Width:1.1"/28 mm
Height:0.43"/11 mm
Length:3.03"/77 mm
0.042 lbs/19 g
Weight
Environmental Considerations Operational Temperatures :
41° to 104°F / 5° to 40°C, 20% to 80% humidity (non-condensing)
Storage Temperatures :
14° to 122°F (-10° to 50°C), 20% to 80% humidity (non-condensing)
1ꢁ0
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
Operation of the USB Wireless LAN Unit is subjected to the regulations of the countries listed below, and may be
prohibited to use outside the country where you purchased.
Supported Countries
Np01Lmꢀ
United Kingdom
Germany
France
Np01Lmꢁ
United States
1
2
Canada
Mexico
3
4
Italy
5
Spain
6
Greece
7
Denmark
Belgium
The Netherlands
Finland
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Sweden
Portugal
Luxembourg
Ireland
Austria
Poland
Hungary
Czech
Slovak
Slovenia
Malta
Estonia
Cyprus
Latvia
Lithuania
Romania
Bulgaria
Norway
Iceland
Liechtenstein
Switzerland
1ꢁ1
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
Cabinet Dimensions
U S B ( L A N )
y B A T N D . O N / S E C R U S O T S
. A O D T J U U A
M
3 D . R E F O R
R
W O E P
S U T A T S
L A M
U S B
P
S E L E C T
M E N U
P U
N
W O D
T
R I G H
L E F T
L E N S S H I F T
399/15.7"
Unit: mm/inch
1ꢁꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
Screen Size and Projection Distance
This section should be used when considering the distance to the screen and the screen size.
Available projection distances are 1.0 m/41.2 inches for 30" screen to 18 m/718 inches for 500" screen, according
to the chart.
(Model)
500
400
Wide
300
Screen size
240
(Diagonal)
Tele
200
150
120
100
80
60
40
30
(m)
22
8
14
16
18
20
6
10
12
2
4
Throw distance
When tilted at an angle 10 in Wide
(m)
10
Tele
Wide
8
6
4
2
Vertical distance between
projector foot and screen
top
Screen center line (Wide)
Screen center line (Tele)
0
(m)
22
8
14
16
18
20
6
10
12
2
Projector foot
4
Vertical lens shift : the highest position
Using the Chart
Example for 100" screen:
The projection distance is approximately 3.1 m (122") according to the upper chart.
The lower chart shows that the vertical distance between the projector foot and the screen top is approximately 1.5
m (59"). The projection angle can be adjusted up to 10°. (The lower chart shows that the projector is placed in a
horizontal position)
1ꢁꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
List of Screen Sizes
List of Screen Sizes
Screen size
Width (H)
Height (V)
m
0.6
0.8
1.2
1.6
2.0
2.4
3.0
4.1
5.1
6.1
8.1
10.2
inch
24.0
m
0.46
0.6
0.9
1.2
1.5
1.8
2.3
3.0
3.8
4.6
6.1
7.6
inch
18.0
Height
Screen size (Diagonal)
30"
40"
31.5
23.6
60"
47.2
35.4
80"
63.0
47.2
100"
120"
150"
200"
250"
300"
400"
500"
78.7
59.1
94.5
70.9
Width
118.1
161.4
200.8
240.2
318.9
401.6
90.6
118.1
149.6
181.1
240.2
299.2
Formulas: Screen width H (m)=Screen size x 4/5 x 0.0254
Screen height V (m)=Screen size x 3/5 x 0.0254
Screen width H (inch)=Screen size x 4/5
Screen height V (inch)=Screen size x 3/5
Screen Size and projection Distance for Desktop when the standard lens is used
The following drawing shows an example for use of Desktop.
Horizontal projection position: Lens centered left to right
Vertical projection position: See the table below.
STANDARD
Screen size
(diagonal)
Projection Distance (L)
(H1)
(inches)
(m)
(inches)
Wide - Tele
0.89 - 1.20
1.20 - 1.62
1.83 - 2.45
2.05 - 2.75
2.21 - 2.96
2.46 - 3.29
2.59 - 3.46
2.78 - 3.71
3.09 - 4.13
3.72 - 4.96
4.66 - 6.21
5.60 - 7.47
6.23 - 8.30
6.54 - 8.72
7.49 - 9.97
7.80 - 10.39
8.43 - 11.23
9.37 - 12.48
12.51 - 16.66
15.65 - 20.83
Wide - Tele
35.1 - 47.3
47.4 - 63.8
72.2 - 96.6
(cm)
0-23
0-30
0-46
0-51
0-55
0-61
0-64
0-69
30"
40"
60"
67"
72"
80"
84"
90"
100"
120"
150"
180"
200"
210"
240"
250"
270"
300"
400"
500"
0-9.0
0-12.0
0-18.0
0-20.1
0-21.6
0-24.0
0-25.2
0-27.0
0-30.0
0-36.0
0-45.0
0-54.0
0-60.0
0-63.0
0-72.0
0-75.0
0-81.0
0-90.0
0-120.0
0-150.0
80.8 - 108.2
87.0 - 116.4
96.9 - 129.5
101.8 - 136.1
109.3 - 146.0
121.6 - 162.4
146.3 - 195.3
183.4 - 244.6
220.5 - 294.0
245.3 - 326.9
257.6 - 343.3
294.7 - 392.6
307.1 - 409.1
331.8 - 442.0
368.9 - 491.3
492.5 - 655.8
616.2 - 820.2
0-76
0-91
0-114
0-137
0-152
0-160
0-183
0-191
0-206
0-229
0-305
0-381
H2 = Screen height (V) - H1
Screen center
Lens center
H2
H1
88 mm/3.47"
L
Projector foot
Screen bottom
NOTE: Distances may vary +/-5%.
1ꢁ4
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
Pin Assignments of D-Sub COMPUTER 1 Input Connector
Mini D-Sub 15 Pin Connector
Signal Level
5
4
3
2
1
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
10
9
8
7
6
15 14 13 12 11
pin No.
RGB Signal (Analog)
YCbCr Signal
1
2
Red
Cr
Y
Green or Sync on Green
Blue
3
Cb
4
Ground
5
Ground
6
Red Ground
Cr Ground
Y Ground
Cb Ground
7
Green Ground
Blue Ground
8
9
No Connection
Sync Signal Ground
No Connection
Bi-directional DATA (SDA)
Horizontal Sync or Composite Sync
Vertical Sync
10
11
12
13
14
15
Data Clock
1ꢁ5
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
Compatible Input Signal List
Signal
Resolution
( Dots )
Frequency H.
( kHz )
Refresh Rate
( Hz )
NTSC
–
15.73
15.63
15.73
15.63
31.47
31.48
35.00
37.86
37.50
39.38
43.27
35.16
37.88
48.08
46.88
53.67
49.72
48.36
56.48
60.24
60.02
68.68
67.50
61.80
60.00
63.98
69.87
–
60.00
PAL
–
50.00
PAL60
–
60.00
SECAM
VESA
–
50.00
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
640 480
640 480
640 480
640 480
640 480
640 480
640 480
800 600
800 600
800 600
800 600
800 600
832 624
1024 768
1024 768
1024 768
1024 768
1024 768
1152 864
1152 900
1280 960
1280 1024
1280 1024
1400 1050
1600 1200
1600 1200
1600 1200
1600 1200
1920 1080
1920 1080
1280 720
1280 720
–
59.94
IBM
59.95
MAC
66.67
VESA
72.81
VESA
75.00
IBM
75.00
VESA
85.01
VESA
56.25
VESA
60.32
VESA
72.19
VESA
75.00
VESA
85.06
MAC
74.55
VESA
60.00
VESA
70.07
MAC
74.93
VESA
75.03
VESA
85.00
VESA
75.00
SUN
65.95
VESA
60.00
VESA
60.02
MAC
65.18
D
SXGA+
VESA
60.00
75.00
81.25
87.50
93.75
33.75
28.13
45.00
37.50
31.25
31.47
15.73
15.63
60.00
VESA
65.00
VESA
70.00
VESA
75.00
D
D
D
D
D
D
HDTV (1080i)(1125i)
HDTV (1080i)(1125i)
HDTV (720p)(750p)
HDTV (720p)
SDTV(576p)(625p)
SDTV (480p)(525p)
DVD YCbCr
DVD YCbCr
60.00 Interlace
50.00 Interlace
60.00 Progressive
50.00 Progressive
50.00 Progressive
59.94 Progressive
59.94 Interlaced
50.00 Interlaced
–
–
–
D: Images above flagged with “D” are supported by digital signal.
NOTE:
• An image with higher or lower resolution than the projector’s native resolution (1024 x 768) will be displayed with scaling tech-
nology.
• Some composite sync signals may not be displayed correctly.
Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh
rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.
1ꢁꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
PC Control Codes and Cable Connection
PC Control Codes
Function.
Code.Data
POWER.ON.
POWER.OFF.
02H. 00H. 00H. 00H. 00H. 02H
02H. 01H. 00H. 00H. 00H. 03H
INPUT.SELECT.COMPUTER.1. 02H. 03H. 00H. 00H. 02H. 01H. 01H. 09H
INPUT.SELECT.COMPUTER.2. 02H. 03H. 00H. 00H. 02H. 01H. 02H. 0AH
INPUT.SELECT.COMPUTER.3. 02H. 03H. 00H. 00H. 02H. 01H. 1AH. 22H
INPUT.SELECT.COMPONENT.
INPUT.SELECT.VIDEO.
INPUT.SELECT.S-VIDEO.
INPUT.SELECT.VIEWER.
PICTURE.MUTE.ON.
PICTURE.MUTE.OFF.
SOUND.MUTE.ON.
SOUND.MUTE.OFF.
ON.SCREEN.MUTE.ON.
ON.SCREEN.MUTE.OFF.
ASPECT.RATIO.(4:3.Screen)
4:3.
02H. 03H. 00H. 00H. 02H. 01H. 10H. 18H
02H. 03H. 00H. 00H. 02H. 01H. 06H. 0EH
02H. 03H. 00H. 00H. 02H. 01H. 0BH. 13H
02H. 03H. 00H. 00H. 02H. 01H. 1FH.
02H. 10H. 00H. 00H. 00H. 12H
02H. 11H. 00H. 00H. 00H. 13H
02H. 12H. 00H. 00H. 00H. 14H
02H. 13H. 00H. 00H. 00H. 15H
02H. 14H. 00H. 00H. 00H. 16H
02H. 15H. 00H. 00H. 00H. 17H
27H
03H. 10H. 00H. 00H. 05H. 18H. 00H. 00H. 00H. 00H. 30H
03H. 10H. 00H. 00H. 05H. 18H. 00H. 00H. 01H. 00H. 31H
03H. 10H. 00H. 00H. 05H. 18H. 00H. 00H. 02H. 00H. 32H
03H. 10H. 00H. 00H. 05H. 18H. 00H. 00H. 03H. 00H. 33H
LETTERBOX.
WIDESCREEN.
zOOM.
ASPECT.RATIO.(16:9.Screen)
4:3.WINDOW.
03H. 10H. 00H. 00H. 05H. 18H. 00H. 00H. 00H. 00H. 30H
03H. 10H. 00H. 00H. 05H. 18H. 00H. 00H. 01H. 00H. 31H
03H. 10H. 00H. 00H. 05H. 18H. 00H. 00H. 02H. 00H. 32H
03H. 10H. 00H. 00H. 05H. 18H. 00H. 00H. 04H. 00H. 34H
LETTERBOX.
WIDESCREEN.
4:3.FILL.
AUTO.ADJUST.
02H. 0FH.
00H. 00H. 02H. 05H. 00H. 18H
NOTE: Contact your local dealer for a full list of PC Control Codes if needed.
Cable Connection
Communication Protocol
Baud.rate............................................38400.bps
Data.length........................................ 8.bits
Parity................................................. No.parity
Stop.bit............................................. One.bit
X.on/off............................................. None
Communications.procedure.............. Full.duplex
NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs.
1ꢁꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
PC Control Connector (D-SUB 9P)
to txd of PC
to rxd of PC
to gnd of PC
1
2
3
4
5
6
7
8
9
to rts of PC
to Cts of PC
NOTE 1: Pins 1, 4, 6 and 9 are no used.
NOTE 2: Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify cable connection.
NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps.
1ꢁ8
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
Removing and Attaching the USB Wireless LAN Unit
Insert the optional USB Wireless LAN Unit into the USB Wireless LAN Unit port on the rear panel of the projector.
Important
•
•
•
•
The USB Wireless LAN Unit consists of two modules: a Wireless LAN module (USB) and a joint module.
Do not insert other USB devices into the USB Wireless LAN unit port.
Do not insert the USB Wireless LAN unit into the USB port (Type A).
The USB Wireless LAN Unit must be inserted into the USB Wireless LAN Unit port in the correct direction.
It cannot be inserted in the reverse direction. If the USB Wireless LAN Unit is inserted in the reverse direction
with excessive force applied, the USB port may break.
•
•
Before touching the USB Wireless LAN Unit, touch a metallic object (such as a door knob or aluminum window
frame) to discharge the static electricity from your body.
Always insert or remove the USB Wireless LAN unit when the main power is turned off. Failure to do so may
cause projector malfunction or damage to the USB wireless LAN unit. If the projector will not work correctly, turn
off the projector, wait 30 seconds, and turn it back on.
•
•
The blue LED on the Wireless LAN Unit flashes to show that Wireless LAN Unit is working.
If the Wireless LAN Unit is attached incorrectly, the blue LED will not light.
To attach the optional USB Wireless LAN Unit to the USB Wireless LAN unit port, follow the in-
structions below.
1. Press POWER ON/STAND BY button to set the projector to Stand-by mode, then press the “O (off)” side
of the main power switch of the projector.
2. Loosen and remove two screws.
L
L
E
E
F
N
S
T
S
H
IF
T
R
IG
H
T
DO
W
N
U
P
SELEC
T
3
D
R
E
F
O
R
M
A
U
T
O
A
D
J
U
S
T
S
O
U
R
C
E
O
N
/S
T
A
N
U
SB
D
B
L
A
Y
M
S
P
T
A
P
T
U
O
S
W
E
R
W
I
R
E
L
E
S
S
S
S
E
L
E
R
I
W
1ꢁ9
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
3. Slowly remove the dummy case or the current attached USB Wireless LAN Unit.
S
E
L
E
C
T
3
D
R
E
F
O
R
M
A
U
T
O
A
D
J
U
S
T
S
O
U
R
C
E
ON/ST
AND BY
U
S
B
L
A
M
S
P
T
A
T
P
U
S
O
W
E
R
WIRLES
WIRLES
4. Slowly remove the dummy case or the Wireless LAN module from the joint module.
WIRLES
S
S
WIRLES
5. Slowly insert the USB Wireless LAN module into the joint module.
WIRLES
S
S
WIRLES
6. Insert the USB Wireless LAN Unit slowly into the USB port on the rear panel of the projector.
NOTE: After inserting, make sure the bottom of the USB Wireless LAN unit is firmly seated against the cabinet.
S
E
L
E
C
T
3
D
R
E
F
O
R
M
A
U
T
O
A
D
J
U
S
T
S
O
U
R
C
E
ON/ST
AND B
U
S
B
L
A
M
S
P
T
A
T
P
U
S
O
W
E
R
WIRLES
WIRLES
7. Tighten the two screws.
L
L
E
E
F
N
S
T
S
H
IF
T
R
IG
H
T
DO
W
N
U
P
SELEC
T
3
D
R
E
F
O
R
M
A
U
T
O
A
D
J
U
S
T
S
O
U
R
C
E
O
N
/S
T
A
N
U
SB
D
B
L
A
Y
M
S
P
T
A
P
T
U
O
S
W
E
R
W
I
R
E
L
E
S
S
S
S
E
L
E
R
I
W
140
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
Troubleshooting Check List
9
Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by
referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem
more efficiently.
* Print the following pages.
Frequency of occurrence...always....sometimes.(How.often?_____________________).....other.(__________________)
power
No.power.(POWER.indicator.does.not.light.green)...See.also.
Shut.down.during.operation.
“Status.Indicator.(STATUS)”.
Power.cable’s.plug.is.fully.inserted.into.the.wall.outlet.
Lamp.cover.is.installed.correctly..
Power.cable’s.plug.is.fully.inserted.into.the.wall.outlet.
Main.power.switch.is.pressed.to.the.ON.position.
Lamp.cover.is.installed.correctly..
Power.Management.is.turned.off.(only.models.with.the.
Power.Management.function).
Lamp.Hours.Used.(lamp.operation.hours).was.cleared.after.
lamp.replacement.
Off.Timer.is.turned.off.(only.models.with.the.Off.Timer.func-
tion.).
No.power.even.though.you.press.and.hold.the.POWER.but-
ton.for.a.minimum.of.2.seconds.
Video and audio
No.image.is.displayed.from.your.PC.or.video.equipment.to.the.
Parts.of.the.image.are.lost.
projector.
Still.unchanged.even.though.you.press.the.AUTO.ADJUST.
button.
Still.no.image.even.though.you.connect.the.projector.to.the.
PC.first,.then.start.the.PC.
Still.unchanged.even.though.you.carry.out.[RESET].in.the.
projector’s.menu.
Enabling.your.notebook.PC’s.signal.output.to.the.projector.
•
A combination of function keys will enable/disable the
external display. Usually, the combination of the “Fn” key
along with one of the 12 function keys turns the external
display on or off.
Image.is.shifted.in.the.vertical.or.horizontal.direction.
Horizontal.and.vertical.positions.are.correctly.adjusted.on.a.
computer.signal.
Input.source’s.resolution.and.frequency.are.supported.by.the.
projector.
No.image.(blue.background,.logo,.no.display).
Still.no.image.even.though.you.press.the.AUTO.ADJUST.but-
ton.
Some.pixels.are.lost.
Image.is.flickering.
Still.no.image.even.though.you.carry.out.[RESET].in.the.pro-
jector’s.menu.
Still.unchanged.even.though.you.press.the.AUTO.ADJUST.
button.
Signal.cable’s.plug.is.fully.inserted.into.the.input.connector
Still.unchanged.even.though.you.carry.out.[RESET].in.the.
projector’s.menu.
A.message.appears.on.the.screen.
(._____________________________________________.)
Image.shows.flickering.or.color.drift.on.a.computer.signal.
The.source.connected.to.the.projector.is.active.and.available.
Still.unchanged.even.though.you.change.[FAN.MODE].from.
[HIGH.ALTITUDE].to.[AUTO].
Still.no.image.even.though.you.adjust.the.brightness.and/or.
the.contrast.
Image.appears.blurry.or.out.of.focus.
Input.source’s.resolution.and.frequency.are.supported.by.the.
projector.
Still.unchanged.even.though.you.checked.the.signal’s.resolu-
tion.on.PC.and.changed.it.to.projector’s.native.resolution.
Image.is.too.dark.
Still.unchanged.even.though.you.adjusted.the.focus.
Remains.unchanged.even.though.you.adjust.the.brightness.
and/or.the.contrast.
No.sound.
Audio.cable.is.correctly.connected.to.the.audio.input.of.the.
Image.is.distorted.
projector.
Image.appears.to.be.trapezoidal.(unchanged.even.though.
you.carry.out.the.[KEySTONE].or.[3D.REFORM].adjustment).
Still.unchanged.even.though.you.adjusted.the.volume.level.
AUDIO.OUT.is.connected.to.your.audio.equipment.(only.
models.with.the.AUDIO.OUT.connector).
other
Remote.control.does.not.work.
Buttons.on.the.projector.cabinet.do.not.work.(.only.models.with.
the.Control.Panel.Lock.function).
No.obstacles.between.the.sensor.of.the.projector.and.the.
remote.control.
Control.Panel.Lock.is.not.turned.on.or.is.disabled.in.the.menu.
Projector.is.placed.near.a.fluorescent.light.that.can.disturb.
the.infrared.remote.controls.
Still.unchanged.even.though.you.press.and.hold.the.EXIT.
button.for.a.minimum.of.10.seconds.
Batteries.are.new.and.are.not.reversed.in.installation..
If.present.on.the.remote.control,.projector.selector.switch.is.
not.used.
141
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
In the space below please describe your problem in detail.
Information on application and environment where your projector is used
projector
Installation environment
Screen.size:.
Screen.type:. .White.matte....Beads...Polarization
.Wide.angle....High.contrast
.Throw.distance:. feet/inch/m
Model.number:
.
.
inch
Serial.No.:
Date.of.purchase:
Lamp.operating.time.(hours):
Lamp.Mode:.
.
.
.Normal...Eco
.Orientation:. .Ceiling.mount....Desktop
Power.outlet.connection:
Information.on.input.signal:
Horizontal.synch.frequency. [..........].kHz
.Connected.directly.to.wall.outlet
Vertical.synch.frequency.
[..........].Hz
.Connected.to.power.cord.extender.or.other.(the.
number.of.connected.equipment______________)
Synch.polarity.
H..(+)...(–)
.Connected.to.a.power.cord.reel.or.other.(the.num-
.
V..(+)...(–)
ber.of.connected.equipment______________)
Synch.type.
.Separate...Composite
.Sync.on.Green
.
Computer
STATUS.Indicator:
Steady.light.
Manufacturer:
.Orange...Green
Model.number:
Notebook.PC../.Desktop.
Native.resolution:
Refresh.rate:
Flashing.light.
[..........].cycles
Remote.control.model.number:
Video.adapter:
Other:
Projector
PC
dVd player
Video equipment
Signal cable
VCR,.DVD.player,.Video.camera,.Video.game.or.other
NEC.standard.or.other.manufacturer’s.cable?
Model.number:........................Length:..............inch/m
Manufacturer:
Model.number:
Distribution.amplifier
Model.number:
Switcher
Model.number:
Adapter
Model.number:
14ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
5) Problems or damage caused by use in hot or humid places, in
TravelCare Guide
vehicles, boats or ships, etc.
6) Problems or damage caused by expendable supplies or de-
vices connected to the product other than those designated by
neC.
TravelCare - a service for international travelers
This product is eligible for “TravelCare”, NEC’s unique international
warranty.
Please note that TravelCare coverage differs in part from coverage
under the warranty included with the product.
7) Problems caused by natural consumption, wear or deteriora-
tion of parts under normal usage conditions.
8) Problems or damage to lamps and other expendable supplies,
Services offered with TravelCare
included parts or optional parts.
This warranty allows customers to receive service on their product at
the NEC and NEC-designated service stations in the countries listed
herein when temporarily traveling internationally for business or plea-
sure.
For details on services offered by the different service stations, please
refer to the “List of TravelCare Outlets” below.
9) Other conditions stipulated in the warranty included with the
product also apply.
NOTE: The product can be used overseas with voltages of 100 to 120V and
200 to 240V by using a power cable suited for the standards and power source
voltage of the country in which the product is being used.
1 Repair services
The product will be repaired and delivered within 10 business days,
List of TravelCare Outlets
not including shipping time.
This list applies as of October 1, 2007.
During the term of warranty, the cost of maintenance parts, labor
costs for repairs and shipping costs within the service station’s cov-
erage area are covered by the warranty.
For the most up-to-date information, please refer to the websites of
the service stations in the various countries on the List of TravelCare
Outlets or to the NEC website at http://www.nec-pj.com.
ꢀ Replacement product rental service
If the customer desires, he or she can rent a replacement product
while the original product is being repaired.
Fee: US$200 for 12 days
In Europe
NEC Europe, Ltd. / European Technical Centre
Address:Unit G, Stafford Park 12, Telford TF3 3BJ, U.K.
Telephone:
+44 1952 237000
This fee must be paid at the local service station in cash or credit
card.
The US$200 rental fee is non-refundable even if the customer rents
it less than 12 days before returning.
Fax Line:
Email Address:
WEB Address:
+44 1952 237006
http://www.neceur.com
The replacement product will be delivered within 3 business days.
If the customer did not return the replacement product within 12
days, the customer will be charged the price of the unit.
If the customer returned the replacement product in a faulty or
damaged condition, the repair cost will be charged to the customer.
Note that this service is not offered in all countries and regions.
Please refer to the “List of TravelCare Outlets”.
(Regions Covered)
EU:
Austria*, Belgium*, Denmark*, Finland*, France*, Germany*,
Greece*, Ireland*, Italy*, Luxembourg*, The Netherlands*,
Portugal*, Spain*, Sweden* and the United Kingdom*
Norway*, Iceland and Liechtenstein
EEA:
In North America
NEC Display Solutions of America, Inc.
Address:500 Park Boulevard, Suite 1100
In addition, this replacement product rental service is not offered
after the product’s warranty has expired.
Itasca, Illinois 60143, U.S.A.
+1 800 836 0655
+1 800 356 2415
vsd.tech-support@necdisplay.com
http://www.necdisplay.com/
Term of warranty
Telephone:
Fax Line:
Email Address:
WEB Address:
1
a. Upon presentation of the warranty or receipt received upon
purchase:
(Regions Covered)
U.S.A. *, Canada*
Valid for the term indicated on the warranty or the normal term
of warranty for the country of purchase.
b. When only the product is brought in:
In Oceania
NEC Australia Pty., Ltd.
Address:
Valid for a period of within 14 months of the date of manufac-
ture indicated by the serial number attached to the product.
New South Wales;
2 When a product whose term of warranty is expired is brought in:
184 Milperra Road, Reversby NSW 2212
Telephone: +61 2 9780 8688 Fax Line: +61 2 9780 8659
Victoria;
Repairs will be offered for a fee. In this case the customer is not
eligible for the replacement product rental service.
3 In the following cases, repairs may be charged, even if the product’
s warranty is still in effect:
Unit 1/6 Garden Road, Clayton VIC 3168
Telephone: +61 3 8562 6245 Fax Line: +61 3 8562 6220
Newcastle;
1) if the term of warranty, model name, serial number and name
of the store of purchase are not indicated on the warranty or
have been altered.
120 Parry Street Newcastle West NSW 2300
Telephone: +61 2 4926 2466
Queensland;
2) Problems or damage caused by dropping or shocks during
shipment or movement by the customer or by improper han-
dling by the customers.
Unit 4/305 Montague Road West End QLD 4101
Telephone: +61 7 3840 5858 Fax Line: +61 7 3840 5866
Goldcoast QLD;
3) Problems or damage caused by improper usage or unwarrant-
Shop1 48 Ferry Road Southport QLD 4215
Telephone: +61 7 5591 3670
able alterations or repairs by the customer.
South Australia;
4) Problems or damage caused by fire, salt damage, gas dam-
age, earthquakes, lightning damage, storm or flood damage or
other natural disasters or such external factors as dust, ciga-
rette smoke, abnormal voltage, etc.
84A Richmond Road, Keswick SA 5035
Telephone: +61 8 8375 5707 Fax Line: +61 8 8375 5757
Western Australia;
45 Sarich Court Osborne Park WA 6017
Telephone: +61 8 9445 5901 Fax Line: +61 8 9445 5999
14ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
WEB Address: http://www.nec.com.au
Hyosung ITX Co., Ltd.
Address:
2nd Fl., Ire B/D. #2, 4Ga, Yangpyeng-Dong,
Youngdeungpo-Gu, Seoul, Korea 150-967
+82 2 2163 4193
(Regions Covered)
Australia*, New Zealand
Telephone:
Fax Line:
+82 2 2163 4196
In Asia and middle East
Email Address:
NEC Display Solutions, Ltd.
Address:
686-1, Nishioi, Oi-Machi, Ashigarakami-Gun,
Kanagawa 258-0017, Japan
+81 465 85 2369
(Regions Covered)
South Korea
Telephone:
Fax Line:
+81 465 85 2393
Lenso Communication Co., Ltd.
Email Address:
WEB Address:
http://www.nec-pj.com
Address:292 Lenso House 4, 1st Floor, Srinakarin Road,
Huamark, Bangkapi, Bangkok 10240, Thailand
Telephone:
+66 2 375 2425
(Regions Covered)
Japan*
Fax Line:
Email Address:
WEB Address:
+66 2 375 2434
http://www.lenso.com
NEC Solutions (China) Co.,Ltd.
Address:
Rm 1903, Shining Building, 35 Xueyuan Rd,
Haidian District Beijing 100083, P.R.C.
+8610 82317788
(Regions Covered)
Thailand
Telephone:
Fax Line:
+8610 82331722
ABBA Electronics L.L.C.
Email Address:
http://www.necsl.com.cn
Address:Tariq Bin Ziyad Road, P.O.Box 327, Dubai,
United Arab Emirates
WEB Address:
Telephone:
Fax Line:
+971 4 371800
+971 4 364283
(Regions Covered)
China
Email Address:
(Regions Covered)
NEC Hong Kong Ltd.
Address:
United Arab Emirates
25/F.,The Metropolis Tower, 10 Metropolis Drive,
Hunghom, Kowloon, Hong Kong
+852 2369 0335
Samir Photographic Supplies
Address:P.O.Box 599, Jeddah 21421, Saudi Arabia
Telephone:
Fax Line:
Email Address:
+852 2795 6618
Telephone:
Fax Line:
+966 2 6828219
+966 2 6830820
http://www.nec.com.hk
Email Address:
WEB Address:
Riyadh
Address:P.O.Box 5519, Riyadh 11432, Saudi Arabia
(Regions Covered)
Hong Kong
Telephone:
Fax Line:
+966 1 4645064
+966 1 4657912
NEC Taiwan Ltd.
Email Address:
Address:7F, No.167, SEC.2, Nan King East Road, Taipei,
Taiwan, R.O.C.
Alkhobar
Address:P.O.Box 238, Alkhobar 31952, Saudi Arabia
Telephone:
+886 2 8500 1714
Fax Line:
Email Address:
WEB Address:
+886 2 8500 1420
http://www.nec.com.tw
Telephone:
Fax Line:
Email Address:
+966 3 8942674
+966 3 8948162
(Regions Covered)
Taiwan
(Regions Covered)
Saudi Arabia
NEC Asia Pte.Ltd.
NOTE: In countries designated with an asterisk(*), replacement product rental
Address:401 Commonwealth Drive, #07-02, Haw Par
Technocentre, Singapore 149598
service are offered.
Telephone:
+65 6 273 8333
Fax Line:
+65 6 274 2226
Email Address:
WEB Address:
http://www.nec.com.sg/ap
(Regions Covered)
Singapore
NEC Systems Integration Malaysia Sdn Bhd
Address:Ground Floor, Menara TA One, 22, Jalan P. Ramlee,
50250 Kuala Lumpur, Malaysia
Telephone:
Fax Line:
+6 03 2178 3600 (ISDN)
+6 03 2178 3789
Email Address:
WEB Address:
http://www.necarecenter.com
(Regions Covered)
Malaysia
144
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
P-1/
,
Date:
/
/
,
TO: NEC or NEC’s Authorized Service Station:
Fm:
(Company & Name with signature)
Dear Sir (s),
I would like to apply your TravelCare Service Program based on attached registration and qualification sheet and agree with
your following conditions, and also the Service fee will be charged to my credit card account, if I don’t return the Loan units
within the specified period. I also confirm following information is correct. Regards.
Application Sheet for TravelCare Service Program
Country,
product purchased :
User’s Company Name :
User’s Company Address :
Phone No., Fax No. :
User’s Name :
User’s Address :
Phone No., Fax No. :
Local Contact office :
Local Contact office Address :
Phone No., Fax No. :
User’s Model Name :
Date of Purchase :
Serial No. on cabinet :
Problem of units per User :
Required Service :
(1) Repair and Return
(1) Credit Card
(2) Loan unit
Requested period of Loan unit :
Payment method :
(2) Travelers Cheque
(3) Cash
In Case of Credit Card :
Card No. w/Valid Date :
145
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
5. Loan Service Charges and Conditions:
Upon acceptance of this NEC Projector, Customer agrees to assume
liability for this loan unit.
Condition of your TravelCare Service Program
Enduser is requested to understand following condition of TravelCare
Service Program and complete the necessary information on the ap-
plication sheet.
The current cost of use of this loan unit is $200.00 USD for 12 calen-
dar days.
1. Service Options:
There are 3 types of “Service” available. Enduser has to understand
following condition and is required to fill in the Application Sheet.
If Customer does not return the unit within the 12 calendar days, Cus-
tomer will be charged the next highest cost up to and including the full
list price to Credit Cards, which price will be informed by NEC Autho-
rized Service Stations. Please see the attached listing of contacts for
each country to arrange for pickup of the loan unit.
1) Repair and Return:
The ’Faulty unit’ is sent or collected from the customer. It is repaired
and returned within 10 days to the customer, excluding transport
time.
If you return to their country of origin with the loan unit, you will be
charged additional freight to return the unit to the loaning country.
There may have a case, repair and return can’t be done by NEC
Authorized Service Station, because of shortage of spare parts due
to same model is not sold in the territory.
Thank you for your understanding of this program.
2) Repair and Return with Loan: (This service is limited to some Ser-
vice Stations)
This service is offered to the Enduser, who cannot wait until their
unit is repaired.
The customer can borrow a unit for $200 up to 12 days. Customer
then sends in inoperable unit to nearest NEC Authorized Service
Station for service. In order to prevent collection problem, Enduser
is required to fill in Application Sheet.
Enduser needs to confirm the availability of the Service to NEC Au-
thorized Service Stations.
3) Loan Only:
For this service, NEC Authorized Service Station supplies the cus-
tomer with a loan unit for US$200 up to 12 days. Customer keeps
the inoperable unit and when customer returns home, customer
arranges to have the projector serviced in the home country.
ꢀ. Warranty Exclusions:
This program does not apply if the Projector’s serial number has been
defaced, modified or removed.
If, in the judgement of NEC Authorized Service Station or its agent the
defects or failures result from any cause other than fair wear and tear
or NEC neglect, or fault including the following without limitation:
1) Accidents, transportation, neglect, misuse, abuse, water, dust,
smoke or default of or by the Customer its employees or agents or
any third party;
2) Failure or fluctuation of electrical power, electrical circuitry, air con-
ditioning, humidity control or other environmental conditions such
as use it in smoking area;
3) Any fault in the attachments or associated products or components
(whether or not supplied by NEC or its agents which do not form
part of the Product covered by this warranty);
4) Any act of God, fire, flood, war, act of violence or any similar occur-
rence;
5) Any attempt by any person other than any person authorized by
NEC to adjust, modify, repair, install or service the product.
6) Any Cross-border charges such as, duty, insurance, tax etc.
ꢁ. Charges for Warranty Exclusions and Out of Warranty Case:
In case faulty unit is under warranty exclusions case or under Out of
Warranty period, NEC Authorized Service Station will Inform estima-
tion of actual service cost to the Enduser with reason.
4. Dead on Arrival (DOA):
Enduser must take this issue up with their original supplier in the
country of purchase.
NEC Authorized Service Station will repair the DOA unit as a Warranty
repair, but will not exchange DOA unit with new units.
Ver. 2 10/07
14ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
|