Invacare® Seating & Positioning Products
HCPCS Code = E2611
HCPCS Code = E2607, E2608 (Gentle Contour)
The Invacare® InTouch™ Pro p e l ™ Ba ck , the general
purpose back support so lightweight and comfortable
consumers will forget it’s there. Hardware installation is
no longer a hassle: just grab it, set it and go. The rigid shell
coupled with a soft contoured foam cushion provides
gentle support and facilitates postural symmetry. The
Propel provides a stable surface for propulsion and
completion of daily living activities. Consumers will leave
ordinary back upholstery in the past when they try the
new InTouch Propel.
The Invacare® InTouch™ Flova ir™ seat cushion was
developed to provide pelvic stability, leg positioning and
pressure management for patients with postural asymmetry
and skin integrity concerns. It incorporates a fluid overlay
used in tandem with the ThinAir™ liner. This allows for pelvic
immersion while minimizing overall product weight. The
insert’s unique channeling method limits the amount of fluid
migration, thus decreasing the chances for “bottoming out.”
The Flovair is a great choice for neuromuscular, TBI or SCI
clients without significant obliquity.
HCPCS Code =E2607, E2608 (Gentle Contour) E2605 (Max Contour)
The Invacare® InTouch™ S t a b ilit e ™ seat cushion was
developed to provide pelvic stability and leg positioning for
patients with postural asymmetry. The Stabilite comes fitted
with a ThinAir™ liner, a unique comfort layer that assists in
redistributing peak pressures away from bony prominences.
© 2007 Invacare Corporation.
All rights reserved. Trademarks are identified by the symbols ™ and ®. All trademarks are
owned by or licensed to Invacare Corporation
unless otherwise noted.
Specifications are subject to change without notification.
Download from Www.Somanuals.com. All Manuals Search And Download.
Invacare® Seating & Positioning Products
Invacare® Seating & Positioning Products
Specifications*
TargIT ™ (page 5)
Stabilite/Flovair Cushions (page 3 and page 4)
Seat width
15" – 24" Gentle
15" – 20" Max
15" – 22" Gentle
15" – 20" Max
3.05 lb. Stabilite
4.20 lb. Flovair
15" – 20" 250 lb.
21" – 24" 350 lb.
2 years
Seat width
15" – 24"
15" – 22"
3 lb.
Seat depth
Seat depth
Product weight
Weight capacity
15" – 20" W
Table of Contents
Product weight
Weight capacity
Limited warranty
300 lb.
500 lb.
2 years
Invacare® Cushions........................................1-7
Absolute™ ........................................................1
Comfort-Mate Extra ......................................2
Stabilite™ ........................................................3
Flovair™ ............................................................4
TargIT™ ............................................................5
Infinity® Cushions ..............................................6
Invacare® Backs ............................................7-8
Propel™ ............................................................7
Personal Back™ 10 ........................................8
Personal Back 10 Plus..................................8
Accessories ..................................................9-10
Specifications ..................................................11
21" – 24" W
Limited warranty
* All weights/measurements are approximate
Infinity Cushions (page 6)
Lo Contour
13" – 22"
15" – 20"
4 lb.
Gentle Contour
13" – 22"
15" – 20"
4 lb.
Max Contour
13" – 22"
15" – 20"
4 lb.
Seat width
Seat depth
Product weight
Weight capacity
Limited warranty
250 lb.
250 lb.
250 lb.
2 years
2 years
2-years
Propel™ Back (page 7)
Personal Backs (page 8)
™
™
Personal Back 10
Personal Back 10 Plus
Width range
16"– 21" (1" increments)
Back height
13" – 14" widths
15" – 26" widths
Back width
Product height
Depth adjust
Angle adjust
16.5"
14", 16"
14", 16"
1.75"
16", 19"
16", 19"
+/-27°
4 lb.
13" – 20", 22", 24", 26"
13" – 20", 22", 24", 26"
Product weight
Weight capacity
Product weight
13" – 20" widths
22" – 26" widths
Weight capacity
13" – 20" widths
22" – 26" widths
Limited warranty
300 lb.
2 years
5 lb.
6 lb.
Limited warranty
10 lb.
11 lb.
*
All weight/measurements are approximate
250 lb.
500 lb.
2 years
250 lb.
500 lb.
2 years
Invacare Corporation
© 2007 Invacare Corporation.
All rights reserved. Trademarks are
identified by the symbols ™ and ®.
All trademarks are owned by or licensed
to Invacare Corporation unless otherwise
noted.
USA
One Invacare Way
Elyria, Ohio
44036-2125
(800) 333-6900
Specifications are subject to change
without notification.
Canada
Invacare Canada Inc.
570 Matheson Blvd E
Unit 8
Mississauga Ontario
L4Z 4G4 Canada
© 2007 Invacare Corporation.
Form No. 06-043 Rev. 04/07
11
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Invacare® Cushions
Invacare® Cushions
Invacare® Absolute™ Series: Simple seating solutions for comfort, fit and function.
For clients with mild to moderate seating needs, the Invacare® Absolute™ Series cushions offers a wide range of simple, but highly
functional solutions. The Absolute cushion is designed to provide comfort at an affordable price.
The Invacare Comfort-Mate Extra cushion goes one step further with a comfortable, molded design and a durable moisture-resistant coating.
HCPCS Code = E2601
HCPCS Code = E2603, E2604
InTouch® Absolute™ Cushion (formerly Essential™ Cushion)
Model no. EC
InTouch® Comfort-Mate Extra Cushion
Model no. CMEX
•
•
•
•
•
•
Low profile, lightweight cushion designed for long-term sitting comfort
Comfortable, molded dual-firmness polyurethane foam promotes good postural position
Moisture-resistant coating seals and protects foam from moisture; easily wipes clean
Breathable, water repellant cover
•
•
•
•
•
Molded polyurethane foam provides comfort and durability
Breathable, water repellant cover
Non-slip bottom with hook and loop fasteners keeps cushion securely in place
Six sizes from 16" x 16" to 20" x 18"
Beveled sides coupled with a firm base for stability and a soft outer layer for comfort
A great fit for the Infinity® Drop Base to get your desired seat-to-floor
Shaped cushion bottom for use on taught sling upholstery
Application Guide
Application Guide
•
•
•
Comfort
•
•
Comfort stability and gentle positioning
Adults and geriatrics, primarily comfort, able to do own weight shift for pressure relief
Good rental wheelchair cushion
Adolescents through geriatrics with long-term comfort needs, who are able to do own weight shift
for pressure relief
•
Good long-term care facility wheelchair cushion
Comfort Thickness
Comfort Thickness
A. Height at adductor
B. Height at abductor
C. Height at rear
A. Height at adductor 3.25"
B. Height at abductor 2.25"
2.625"
3.0"
C. Height at rear
2"
1.75"
2.25"
D. Height at leg trough
C
Cushion weight approximately 2.3 lb.
(18" x 16" cushion w/cover)
B
A
1
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Invacare® Cushions
Invacare® Cushions
(Gentle Contour)
(Max Contour)
HCPCS Code = E2607, E2608
HCPCS Code = E2607, E2608
E2605
Flovair
Stabilite
The Flovair™ seat cushion was developed to provide pelvic stability, leg position-
ing and pressure management for patients with postural asymmetry and skin
integrity concerns. It incorporates a fluid overlay used in tandem with the
ThinAir™ liner. This allows for pelvic immersion while minimizing overall product
weight. The insert’s unique channeling method limits the amount of fluid migra-
tion, thus decreasing the chances for “bottoming out.” The Flovair is a great
choice for neuromuscular, TBI or SCI clients without significant obliquity.
The Stabilite™ seat cushion was developed to provide pelvic stability and leg
positioning for patients with postural asymmetry. The Stabilite comes fitted with
a patent-pending ThinAir™ liner, a unique comfort layer that assists in redistribut-
ing peak pressures away from bony prominences. The Stabilite is a great choice
for geriatric or CVA clients.
Features
Functional Benefits
Positioning foam base
+
Supports the pelvis and thighs; helps to prevent adduction and
internal rotation
Features
Functional Benefits
ThinAir™ liner
Positioning foam base
Supports the pelvis and thighs; helps to prevent adduction and
internal rotation
Helps reduce shear
Gentle/Max contour
Contour choices based on involvement level
InTouch™ Stabilite™
InTouch™ Flovair™
Fluid + ThinAir™ liner
+
Effectively redistributes pressure without weight penalty.
Additional shear reduction as two layers work in
harmony.
“Stable + Light”
“Fluid over Air”
Model no. ITSG, ITSM
Model no. ITFG, ITFM
Gentle/Max contour
Contour choices based on involvement level
Positioning Support Base
The larger the surface area, the lower the
pressure. Our engineers put purpose behind the
contouring of the InTouch base to mimic the
shape of the seated human body. Leg troughs
are slightly abducted. Soft foam envelops the
IT’s, coccyx and sacrum. Firmer foam supports
the trochanters while preventing hammocking.
Smooth, refined transitions are sculpted to
replace steep ridges or uncomfortably placed
abductors.
Contour Thickness
Features
Medial thigh support
Functional Benefits
Gentle control of mild adduction tendency
Gentle Max
Contour Contour
Raised adductors
Positioning guidance to maintain proper alignment of lower
extremities
A. Height at adductor 3.5"
B. Height at abductor 3.5"
C. Height at leg trough 2.87"
4.38"
4.38"
2.88"
Sacral relief
Provides additional comfort and support for those sitting in anterior
to posterior pelvic tilt
Pre-ischial elevation
Lateral pelvic support
Limits forward migration of pelvis and sliding out of position
Intended to maintain pelvis in a centered position on the seat and
provide lateral stability
Low profile
Reduces seat-to-floor height for foot propulsion and lateral transfers
InTouch™ Flovair™/Stabilite™ Gentle Contour InTouch™ Flovair™/Stabilite™ Max Contour
If the base isn’t right, then nothing else matters!
3
4
Maximize surface area
Download from Www.Somanuals.com. All Manuals Search And Download.
Invacare® Cushions
Invacare® Cushions
HCPCS Code = E2607, E2608
Invacare® Single Density Cushion
Model no. SD
with
•
Contoured deformation cut foam provides com-
fort and stability
Technology
•
•
Available in over 100 custom sizes
Water repellent cover with non-slip bottom
B
A
C
Application
Cushion Thickness
•
•
•
Comfort
A. Height at rear (adductor)
2"
Adult and geriatric, able to do own weight shift for pressure relief
Good rental wheelchair cushion
InTouch™ TargIT™ Max and Gentle Contour Cushion
B. Height at rear (center)
C. Height at front
1.5"
2.5"
Invacare® InTouch™ TargIT™ is the industry standard for consumers who require moderate skin protection and positioning. The
large, anatomically-shaped pelvic surface of the InTouch cushion eliminates the guesswork of placing a consumer in contact with
pressure-relieving material. The construction of the InTouch TargIT incorporates an exclusive Blend ™ foam molding technology
Cushion weight approximately 2 lb.
Invacare® Infinity® Cushions
2
that fuses the polyurethane base foam with visco-elastic pressure-relieving foam to eliminate transitional edges, providing worry-
free fit and comfort.
Positioning Support Base
Features
Model no. ITTG, ITTM
• InTouch™ Zone technology
• Blend2™ foam molding technology
and prevent bottoming out.
• Sacral relief
The support base of the TargIT cushion is constructed with molded
polyurethane foam contoured to promote comfort, enhance positioning
• Gentle/Contour
ViscoFoam
FloGel®
AirFlo™
Features:
Functional Benefits:
• Bariatric sizes available
Model no. ILCVF, IGCVF, IMCVF
Model no. ILCFG, IGCFG, IMCFG
Model no. ILCAIR, IGCAIR, IMCAIR
• Medial Thigh Support (Abductor) Gentle control of mild adduction tendency
ViscoFoam is an excellent choice for clients who:
FloGel® is an excellent choice for clients who:
AirFlo™ is an excellent choice for clients who:
• Raised Adductors
Positioning guidance to maintain proper
alignment of lower extremities
•
•
•
Are at high risk of skin breakdown
Require excellent support and stability
Require a lightweight cushion
•
•
•
Are at high risk of skin breakdown
Require excellent support and stability
Require a good dynamic shear reduction
•
•
•
Have a history of or are considered to be at
very high risk of skin breakdown
Contour Thickness
• Mild Hip Guides
Adductors are extended posteriorly to keep
user centered on cushion
Require an air flotation insert for immersion
of bony prominences
• Pre-contoured sacral area
Provides additional comfort and support
for those sitting in anterior to posterior
pelvic tilt
Require a postural support base for stability
• Pre-ischial shelf w/ 15˚ drafted
edge
Limits forward migration of pelvis and
sliding out of position
• Low profile (Gentle)
Reduces seat-to-floor height for foot
propulsion and lateral transfers
InTouch™ TargIT Max Contour
™
™
InTouch™ TargIT Gentle Contour
Ideal for clients who require a mild to
moderate level of postural support
Gentle
Contour Contour
Max
• Deep IT relief well (Max)
Provides maximum pelvic immersion and
control
Ideal for clients who require a moderate to
high level of postural support
LoContour
Gentle Contour
Max Contour
A. Height at adductor
B. Height at abductor
3.625"
3.625"
4.35"
4.35"
2.85"
LoContour is an excellent choice for clients who:
Gentle Contour is an excellent choice for clients
who:
Max Contour is an excellent choice for clients
who:
•
•
•
•
Have good postural control
Have low to normal muscle tone
Laterally transfer
C. Height at leg trough 2.50"
•
•
•
Have moderate postural instability
•
•
•
Require high level of postural control
Require gentle control of tone
Need maximum control of tone
Need moderate control of
Require optimal pressure reduction
and redistribution
5
Foot propel
6
abduction/adduction tendency
Download from Www.Somanuals.com. All Manuals Search And Download.
Invacare® Backs
Invacare® Backs
Introducing the Invacare® InTouch™ Propel™, the general purpose back support so lightweight and comfortable consumers will forget
it’s there. Hardware installation is no longer a hassle: just grab it, set it and go. The rigid shell coupled with a soft contoured foam
cushion provides gentle support and facilitates postural symmetry. The Propel provides a stable surface for propulsion and
completion of daily living activities. Consumers will leave ordinary back upholstery in the past when they try the new InTouch Propel.
HCPCS Code = E2615, E2616
The Personal Back™10
and Personal Back™10 Plus
combine simplicity of design
with effectiveness of
HCPCS Code = E2611
application. The highly popular
Personal Back line continues to
provide the comfort, postural
support, and spinal alignment
that you have come to expect.
Scapular cut-outs
Support
™
™
Personal Back 10 Plus
Personal Back 10
Model no. PPR, PPT
Model no. PBR, PBT
1-handed quick release
Features
The Personal Back10 Plus is an excellent choice for clients
who require comfort and stability with increased midline
support. It often is recommended when using the foam-in-
place kit.
The Personal Back10 is an excellent choice for clients who
require comfort and stability with moderate midline support.
• Lightweight aluminum shell
• Pre-contoured shell provides
excellent contact and support
Comfort and contour
• Pre-drilled headrest pattern
™
• Quick Set hardware with
increased adjustability
• Bariatric sizes available: 22", 24"
and 26" widths at 500 lb. weight
capacity
Lightweight, durable, aluminum shell is pre-
contoured to provide excellent contact and
support.
Pre-drilled headrest mounting pattern
accommodates most major manufacturers’
headrest systems.
Deep lateral contour of the Personal Back10 Plus
provides increased midline support without
interfering with upper extremity
range of motion.
Adjust depth/angle while client is seated
Positioning
Dimensions
All measurements in inches.
Redundant
tissue cut-outs
Features
Model no. ITPR
• 4-way adjustability: height/width/depth/angle
• 1-handed quick release
• 1-tool assembly (7/8" wrench)
• 2-point mountings fit 7/8" to 1" canes
• 3-point comfort foam
Fits 7/8" or 1" canes with no additional hardware.
• Adjustment while patient is seated
™
™
Personal Back 10
Personal Back 10 Plus
™
Personal Back 10
Personal Back Back Heights
Width
Regular
14"
Tall
16"
19"
Width 13"
14"
15"
16"
17"
18"
19"
20"
22"
24"
16.25
20.50
6.75
26"
13" - 14"
15" - 26"
A
B
C
12.25
9.50
5.00
12.25
10.50
5.25
13.25 13.25 14.25
11.50 12.50 13.50
14.25
14.50
5.75
15.25
15.50
6.00
15.25 16.25
16.50 18.50
17.25
22.50
7.25
16"
5.50
5.50
5.75
6.00
6.50
™
Personal Back 10 Plus
Width 13"
14"
13.00
9.50
7.00
15"
16"
17"
18"
15.00
11.50
7.50
19"
16.00
12.50
7.75
20"
22"
24"
17.00
13.50
8.5
26"
18.00
14.50
8.75
A
B
C
13.00
9.50
6.75
14.00 14.00 15.00
10.50 10.50 11.50
16.00 17.00
12.50 13.50
7.25
7.25
7.50
7.75
8.25
8
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Invacare® Seating & Positioning Accessories
Invacare® Seating & Positioning Accessories
Cushion Rigidizer
➤
➤ Full Tray -
Hook and Loop Mount
• Lightweight plastic seat insert
• Break-resistant clear polycarbonate
tray surface
• Securely attaches to bottom of
cushion inside cover
• Easily attaches to chair armrest
with hook and loop straps
• Fits between seat rails for level
support
• Removable trim allows thorough
cleaning
• Eliminates hammock effect of
seat upholstery
Adjustable Headrests ➤
Belts and Straps ➤
• Contoured head and neck supports
available in four styles
• Three sizes of shoulder supports
fit child, junior and adult
• Dual-ball swivel hardware for
multi-plane adjustment
• Three sizes of padded lap belts fit
child, junior and adult - pinch
release buckles
• Durable steel reinforced
polyurethane pads - easily
wipe clean
• Push-button style release provides
secure attachment
• Three sizes of four-point lap belt to
fit child, junior and adult - push but-
ton release buckle
®
Infinity Drop Base
➤
• Width adjustable: Three sizes fit
wheelchairs from 14" to 22" wide
• Height and angle adjustable:
Up to 2" of drop provided
• Portable quick-release hardware
allows easy removal of base from
wheelchair
Full Tray - Slide-on Mount
➤
• Break-resistant clear polyester
resin tray surface
• Width adjustable mounting
hardware securely fastens tray to
chair arm pads
Basic Headrest ➤
• Padded to provide comfortable
occipital support
• Molded-in rim helps keep items
on tray
• Horizontal and vertical adjustable
hardware
• Outer cover easily removes for
laundering
Half Tray - Swingaway ➤
• Break-resistant clear polycarbonate
tray surface
➤
Foam-In-Place Kit
• Tray securely bolts to wheelchair
armrest
• Easy-to-use Foam-in-Place kit
provides custom foam mold insert
in minutes
• Tray easily swings away when
not in use
• Can be used with Personal
Back™10/Personal Back™10 Plus
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|