Snapper Lawn Mower SPV21675FC SPV21675EFC User Manual

Safety Instructions & Operator's Manual for  
21” VARIABLE SPEED  
REAR DISCHARGE  
WALK BEHIND  
MOWERS  
Models  
SPV21675FC (7800265)  
SPV21675EFC (7800266)  
NOTE: Specifications are correct at time of printing and are subject to change without notice.  
* Actual sustained engine power will likely be lower due to operating limitations and environmental factors. Please refer to ‘Engine Power Rating Information’ for  
further details.  
Manual No. 7101688 (Rev. ‘-’, 4/7/2008)  
TP 100-5387---WB-N  
Table of Contents  
Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
Important Operator Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Pre-Start Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Starting & Stopping Engine & Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Propelling Mower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
Handle Height Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
Cutting Height Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
Recycling Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
Installing the Discharge Deflector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8  
Removing the Recycling Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8  
Installing the Grass Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8  
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Change Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Check Mower Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Check Engine Drive Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Service - Periodic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Wheel Drive Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10  
Storage Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10  
Mower Blade Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11  
Blade Sharpening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11  
Wheel Drive Control Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12  
Belt Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13  
Engine Drive Belt Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13  
Battery Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14  
Rear Cover Removal & Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15  
Service Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17  
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
Slope Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
WARNING  
WARNING  
!
!
!
!
Battery posts, terminals and related accessories contain  
lead and lead compounds, chemicals known to the State of  
California to cause cancer and birth defects or other  
reproductive harm. Wash hands after handling.  
Engine exhaust, some of its constituents, and certain  
vehicle components contain or emit chemicals known to  
the State of California to cause cancer or other reproductive  
harm.  
1
IMPORTANT OPERATOR SAFETY INSTRUCTIONS  
!
!
WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects  
that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in  
serious injury or death to the operator or other persons. The owner of the machine must understand these  
instructions and must allow only persons who understand these instructions to operate machine. Each  
person operating the machine must be of sound mind and body and must not be under the influence of any  
substance, which might impair vision, dexterity or judgment. If you have any questions pertaining to your  
machine which your dealer cannot answer to your satisfaction, call or write the Customer Service  
Department at SNAPPER, McDonough, Georgia 30253. Phone: (1-800-317-7833).  
PROTECTION FOR CHILDREN  
PREPARATION  
(Continued From Previous Column)  
Tragic accidents can occur if the operator is not alert to the  
presence of children. Children are often attracted to the  
machine and the mowing activity. Never assume that  
children will remain where you last saw them.  
Add fuel outdoors only with engine stopped and cool. Clean  
spilled fuel and oil from machine. DO NOT smoke.  
5. Check the area to be mowed and remove all objects such  
as toys, wire, rocks, limbs and other objects that could  
cause injury if thrown by blade or interfere with mowing.  
Also note the location of holes, stumps, and other possible  
hazards.  
1. KEEP children out of the mowing area and under the  
watchful care of a responsible adult other than the operator.  
2. DO NOT allow children in yard when machine is operated  
and turn machine OFF if anyone enters the area.  
3. DO NOT allow pre-teenage children to operate machine.  
4. ALLOW only responsible adults & teenagers with mature  
judgment under close adult supervision to operate machine.  
5. DO NOT pull mower backwards unless absolutely  
necessary. LOOK and SEE behind and down for children,  
pets and hazards before and while backing.  
6. Keep people and pets out of the mowing area.  
Immediately, STOP Blade, Stop engine and Stop mower if  
anyone enters the area.  
7. Check shields, deflectors, switches, blade controls and  
other safety devices frequently for proper operation and  
location.  
6. USE EXTRA CARE when approaching blind corners,  
shrubs, trees, or other objects that may obscure vision.  
8. Make sure all safety decals are clearly legible. Replace if  
damaged.  
9. Protect yourself when mowing and wear safety glasses,  
long pants and substantial footwear. DO NOT mow  
barefooted or with sandals.  
10. Know how to STOP blade and engine quickly in  
preparation for emergencies.  
11. Use extra care when loading or unloading the machine  
into a trailer or truck.  
12. Check grass catcher components frequently for signs of  
wear or deterioration and replace as needed to prevent  
injury from thrown objects going through weak or torn  
spots.  
SLOPE OPERATION  
1. Slopes are a major factor related to slip and fall  
accidents, which can result in severe injury. All slopes  
require extra caution. If you feel uneasy on a slope, DO NOT  
mow it.  
2. Mow across slopes, never up-and-down. Exercise  
extreme CAUTION when changing directions on slopes. DO  
NOT mow steep slopes or other areas where stability or  
traction is in doubt. Refer to the Slope Guide at the back of  
this manual.  
3. Use extra care with grass catchers or other attachments;  
these affect the handling and the stability of the machine.  
SAFE HANDLING OF GASOLINE  
To avoid personal injury or property damage, use extreme  
care in handling gasoline. Gasoline is extremely flammable  
and the vapors are explosive.  
1. Extinguish all cigarettes, cigars, pipes and other sources  
of ignition.  
PREPARATION  
1. Read, understand, and follow instructions and warnings  
in this manual and on the mower, engine and attachments.  
Know the controls and the proper use of the mower before  
starting.  
2. Use only an approved fuel container.  
2. Only mature, responsible persons shall operate the  
machine and only after proper instruction.  
3. Data indicates that operators age 60 and above, are  
involved in a large percentage of mower-related injuries.  
These operators should evaluate their ability to operate the  
mower safely enough to protect themselves and others  
from serious injury.  
4. Handle fuel with extra care. Fuels are flammable and  
vapors are explosive. Use only an approved fuel container.  
DO NOT remove fuel cap or add fuel with engine running.  
3. DO NOT remove fuel cap or add fuel with the engine  
running. Allow the engine to cool before refueling.  
4. DO NOT refuel the machine indoors.  
5. DO NOT store the machine or fuel container inside where  
there is an open flame, spark or pilot light such as on a  
water heater or other appliances.  
6. DO NOT fill fuel containers inside a vehicle or on a  
truck or trailer bed with a plastic liner. Always place the  
containers on the ground away from the vehicle before  
filling.  
2
IMPORTANT OPERATOR SAFETY INSTRUCTIONS (Continued)  
!
!
SAFE HANDLING OF GASOLINE  
OPERATION  
(Continued From Previous Page)  
7. Remove gas-powered equipment from the vehicle or  
trailer and refuel it on the ground. If this is not possible,  
then refuel equipment using a portable container, rather  
than a gasoline dispenser nozzle.  
(Continued From Previous Column)  
14. DO NOT discharge material against a wall or  
obstruction. Material may ricochet back towards the  
operator.  
15. Slow down before turning.  
8. DO NOT start gas powered equipment in enclosed  
vehicles or trailers.  
9. Keep the nozzle in contact with the rim of the fuel tank or  
container opening at all times until fueling is complete. DO  
NOT use a nozzle lock-open device  
10. If fuel is spilled on clothing, change clothing  
immediately.  
16. Watch out for traffic when near or crossing roadways.  
17. DO NOT operate engine in enclosed areas. Engine  
exhaust gases contain carbon monoxide, a deadly poison.  
18. Only use accessories approved by the manufacturer.  
See manufacturer’s instructions for proper operation and  
installation of accessories.  
11. DO NOT overfill a fuel tank. Replace fuel cap and tighten  
securely.  
MAINTENANCE AND STORAGE  
1. DO NOT store mower or fuel container inside where  
fumes may reach an open flame, spark or pilot light such as  
in a water heater, furnace, clothes dryer or other gas  
appliance. Allow engine to cool before storing machine in  
an enclosure. Store fuel container out of reach of children  
in a well ventilated, unoccupied building.  
OPERATION  
1. DO NOT put hands or feet near or under rotating parts.  
Keep clear of discharge area while engine is running.  
2. STOP engine when crossing gravel drives, walks, or  
roads, and under any conditions where thrown objects  
might be a hazard.  
2. Keep mower and engine free of grass, leaves or excess  
grease to reduce fire hazard and engine overheating.  
3. When draining fuel tank, drain fuel into an approved  
container outdoors and away from open flame.  
4. Keep all bolts, especially blade bolts, nuts and screws  
properly tight. Check that all cotter pins are in proper  
position.  
5. Always provide adequate ventilation when running  
engine. Engine exhaust gases contain carbon monoxide, a  
deadly poison.  
6. Service engine and make adjustments only when engine  
is stopped. Removed spark plug wire from spark plug and  
secure wire away from spark plug to prevent accidental  
starting.  
7. DO NOT change engine governor speed settings or  
overspeed engine.  
8. Check grass bag assembly frequently for wear or  
deterioration to avoid thrown objects and exposure to  
moving parts. Replace with new bag if loose seams or tears  
are evident. Replace slider or bag adapter if broken or  
cracked.  
9. Mower blades are sharp and can cut. Wrap the blades or  
wear heavy leather gloves and use CAUTION when handling  
them.  
10. DO NOT test for spark by grounding spark plug next to  
spark plug hole; spark plug could ignite gas exiting engine.  
11. Have machine serviced by an authorized SNAPPER  
dealer at least once a year and have the dealer install any  
new safety devices.  
3. Mow only in daylight or good artificial light.  
4. DO NOT operate mower while under the influence of  
alcohol or drugs.  
5. After striking a foreign object or if mower vibrates  
abnormally, STOP the engine, disconnect and secure spark  
plug wire. Inspect the mower for any damage and repair the  
damage before starting.  
6. DO NOT mow near drop offs, ditches or embankments.  
Operator could lose footing or balance.  
7. STAY ALERT for holes and other hidden hazards. Tall  
grass can hide obstacles. Keep away from ditches,  
washouts, culverts, fences and protruding objects.  
8. DO NOT mow on wet grass. Always be sure of your  
footing. Keep a firm hold on the handle and walk, never run.  
Slipping could cause injury.  
9. ALWAYS stay behind handle when engine (motor) is  
running.  
10. DO NOT leave the machine with the engine running.  
STOP BLADE and STOP ENGINE before leaving the  
operators position for any reason.  
11. Before cleaning, repairing or inspecting make certain  
engine, blade and all moving parts have STOPPED.  
Disconnect and secure spark plug wire away from plug to  
prevent accidental starting.  
12. STOP engine and wait until the blade comes to  
complete STOP before removing grass bag and/or clearing  
grass.  
13. DO NOT operate mower without the entire grass  
catcher, or guards in place discharge guard, rear guard or  
other safety devices in place and working. DO NOT point  
discharge at people, passing cars, windows or doors.  
12. Use only genuine SNAPPER replacement parts to  
assure that original standards are maintained.  
3
IMPORTANT  
The figures and illustrations in this manual are provided  
for reference only and may differ from your specific model.  
Contact your Snapper dealer if you have questions.  
F
G
H
J
I
B
A
D
E
C
Features and Controls  
A.  
B.  
C.  
D.  
E.  
Oil Fill Cap and Dipstick  
Fuel Filler Cap  
F.  
Blade Control  
G.  
H.  
I.  
Rope Start Handle  
Drive Wheel Control  
Rear Discharge Door  
Grass Bag  
Recycling Cover  
Battery Box  
Height Adjustment Lever  
J.  
4
Pre-Start Check List  
Starting and Operation  
Make the following checks and perform the service required  
before each start-up.  
Engine and Blade  
1. Pull the blade control (A, Figure 3) against the handle.  
2. Start the mower:  
1. Check the guards, deflectors, grass bag, and covers to  
make sure all are in place and securely tightened.  
2. Check the blade control (A, Figure 1) and wheel drive  
control (B) to insure they work freely.  
Manual Start Models: Pull the rope start handle (B)  
to crank the engine.  
Electric Start Models: Insert the key (C) into the  
ignition switch (D), located on the right side of the  
handle above the rope guide. Turn the key to crank  
the engine.  
3. After the engine starts, allow a brief warm-up until the  
engine runs smooth before beginning mower operation.  
A
NOTE: To stop the engine (and blade), release the blade  
control.  
B
A
Figure 1: Mower controls  
3. Check the cutting height. Adjust to the desired height.  
Refer to the Section ‘Cutting Height Adjustment’.  
4. Check the engine oil and add oil as needed to bring the  
level up to the full mark (A, Figure 2). Refer to the  
Engine Owner’s Manual for oil specifications.  
B
D
A
C
Figure 3: Starting the mower  
Figure 2: Checking engine oil  
5. Add fuel to the tank after pushing the mower outside  
where fumes can safely dissipate. Fill the tank to 1-1/2  
inches below the top of the filler neck (to allow for fuel  
expansion). Make sure the cap is tightened after fueling.  
Refer to the Engine Owners Manual for fuel  
specifications.  
6. Clean the exterior surfaces of the cutting deck and  
engine of any accumulation of spilled fuel, dirt, grass,  
oil, etc. Keep the engine air intake screen and cooling  
fins clear at all times.  
7. Perform battery service. Refer to the Section ‘Battery  
Service’.  
5
Starting and Operation (Continued)  
Handle Height Adjustment  
The height of the mower handle can be adjusted as follows:  
1. Turn the two locking cams (A, Figure 5) a quarter-turn  
to unlock the handle assembly (B).  
Propelling the Mower  
1. Start the engine. Refer to the Section entitled “Starting  
and Operation – Engine and Blade”.  
2. Begin squeezing the wheel drive control (A, Figure 4)  
back toward the handle to engage the wheel drive and  
propel the mower forward. Forward speed can be  
increased by squeezing the wheel drive control further  
back toward the handle.  
2. Align the handle assembly with one of the three handle  
height adjustment holes (C) in the mounting brackets.  
3. Return the locking cams to their original position to lock  
the handle.  
C
A
B
A
Figure 4: Wheel drive control  
(Components removed for clarity)  
Figure 5: Adjusting the handle height  
Stopping  
WARNING  
!
!
1. Stop forward motion of the mower by releasing the  
wheel drive control.  
DO NOT attempt any maintenance, adjustments or service  
with engine and blade running. STOP engine and blade.  
Disconnect spark plug wire and secure away from spark  
plug. Engine and components are HOT. Avoid serious  
burns, allow sufficient time for all components to cool.  
2. Stop the engine and blade by releasing the blade  
control.  
6
WARNING  
!
!
DO NOT attempt any maintenance, adjustments or service  
with engine and blade running. STOP engine and blade.  
Disconnect spark plug wire and secure away from spark  
plug. Engine and components are HOT. Avoid serious  
burns, allow sufficient time for all components to cool.  
1.50 in  
4.00 in  
Cutting Height Adjustment  
Figure 7: Cutting height settings (approximate)  
1. Pull the height adjusting lever (A, Figure 6) outward,  
and move to the desired cutting height. The highest  
cutting position is Notch 9 (B; also see Figure 7). The  
lowest cutting position is Notch 1 (C).  
Recycling Operation  
Note: For best recycling results, cut up to a maximum of 1/3  
of grass blade length and recycle ONLY when grass is dry.  
1. Set the height adjustment lever in the highest cutting  
position (Notch 9). Refer to the Section entitled “Cutting  
Height Adjustment”.  
Note: The lever will set all wheels to the same cutting height.  
WARNING  
!
!
Stop engine and mower blade by releasing the blade  
control before adjusting cutting height.  
2. Proceed mowing slowly. If the grass is very dense,  
lower the height adjustment lever one notch lower to  
improve recycling performance.  
A
Installing the Discharge Deflector  
1. Raise the recycling cover (A, Figure 8).  
Important: The recycling cover should remain on the  
machine at all times. Do not remove.  
C
A
D
B
C
B
Figure 8: Installing the discharge deflector  
Figure 6: Adjusting cutting height  
2. Install the deflector (B) to the deck under the recycling  
cover, making sure that:  
The tabs (C) hook under the pivot rod (D).  
The locking tab on the deck (A, Figure 9) goes  
through the slot in the deflector (B).  
3. Lower the recycling cover against the deflector.  
7
Installing the Grass Bag  
WARNING  
!
!
1. Raise the rear discharge door (A, Figure 11).  
2. Remove the recycling plug. Refer to the section entitled  
“Removing the Recycling Plug”.  
DO NOT attempt any maintenance, adjustments or service  
with engine and blade running. STOP engine and blade.  
Disconnect spark plug wire and secure away from spark  
plug. Engine and components are HOT. Avoid serious  
burns, allow sufficient time for all components to cool.  
3. Holding the grass bag handle (B), install the grass bag  
onto the back of the mower, making sure that the grass  
bag hooks (A, Figure 12) are hooked onto the rear door  
pivot rod (B).  
B
A
A
B
Figure 11: Installing the grass bag  
Figure 9: Deflector locking tab  
A
Removing the Recycling Plug  
1. Raise the rear discharge door (A, Figure 10).  
2. Remove the recycling plug (B) from the rear discharge  
chute.  
Note: The recycling plug should be removed only when  
bagging is desired, and should be replaced as soon as  
bagging operations are completed.  
B
Figure 12: Grass bag hooks  
B
WARNING  
!
!
A
Grass Catcher bags used on SNAPPER products are made  
of woven fabric, and are subject to deterioration and wear  
during normal usage. Check condition of bag before each  
use. Immediately replace worn or damaged catcher bags  
with only bags recommended by SNAPPER. The grass  
catcher is optional equipment on some models.  
Figure 10: Removing the recycling plug  
8
Check Mower Blade  
Maintenance - Introduction  
1. Disconnect the spark plug wire and secure the end away  
from the plug.  
To retain the quality of the mower, use genuine SNAPPER  
replacement parts only. Contact a local SNAPPER dealer for  
parts and service assistance. For the correct part or  
information for a particular mower, always mention the  
model and serial number.  
2. Tilt the mower up on its rear wheels for access to the  
blade cap screw (A, Figure 14). Do not tilt the mower  
with the spark plug or carburetor down.  
Important: Drain the fuel tank before tipping the mower. DO  
NOT tip the machine with the carburetor or spark plug down.  
Oil from the crankcase will saturate the air filter and cause  
the engine to be hard to start or not start at all. If  
contamination does occur, the air filter will have to be  
replaced.  
WARNING  
!
!
DO NOT attempt any maintenance, adjustments or service  
with engine and blade running. STOP engine and blade.  
Disconnect spark plug wire and secure away from spark  
plug. Engine and components are HOT. Avoid serious  
burns, allow sufficient time for all components to cool.  
Wear heavy leather gloves when handling or working  
around cutting blades. Blades are extremely sharp and can  
cause severe injury.  
A
Service - After First 5 Hours  
Change Engine Oil  
1. Refer to the Engine Manual for proper oil specifications,  
procedures and proper service intervals.  
2. For the simplest/cleanest oil change, simply turn the  
mower on its side to drain the oil, as shown. Drain the  
oil through the dipstick tube (A, Figure 13) into a  
container. Allow sufficient time for all the oil to drain.  
Figure 14: Tightening the blade cap screw  
Important: Drain the fuel tank before tipping the machine.  
DO NOT tip the machine with the carburetor or spark plug  
down. Oil from the crankcase will saturate the air filter and  
cause the engine to be hard to start or not start at all. If  
contamination does occur, the air filter will have to be  
replaced.  
3. Check the torque of the blade cap screw. Recommended  
torque should be 40 ft. lbs.  
4. Check the blade for sharpness, wear and damage. Refer  
to the Section entitled “Blade Wear Limits”.  
Check Engine Drive Belt  
1. Visually check the engine drive belt for cracking, fraying,  
severed or exposed belt strands. If worn or damaged,  
replace the belt before operating the mower.  
Service - Periodic  
Perform all maintenance as described in the “Service  
Schedule” section of this manual.  
Engine  
Service the engine according to the engine owner’s manual.  
A
Air Filter  
Refer to the engine owner’s manual for service instructions.  
Figure 13: Draining the engine oil  
Engine Oil  
Refer to the engine owner’s manual for service instructions.  
3. Dispose of drain oil properly.  
4. Fill the engine with oil as specified in the Engine Manual.  
Do Not overfill.  
9
WARNING  
!
!
DO NOT attempt any maintenance, adjustments or service  
with engine and blade running. STOP engine and blade.  
Disconnect spark plug wire and secure away from spark  
plug. Engine and components are HOT. Avoid serious  
burns, allow sufficient time for all components to cool.  
Wear heavy leather gloves when handling or working  
around cutting blades. Blades are extremely sharp and can  
cause severe injury.  
Wheel Drive Components  
1. Remove the rear cover. Refer to the Section entitled  
“Rear Cover Removal & Installation”.  
2. Clean any debris buildup on or around the transmission,  
axles, idler, pulleys, belt, etc., as well as on the inside of  
the cover. Check components for wear or damage.  
Replace worn or damaged components immediately.  
3. Replace the rear cover.  
Important: DO NOT operate the mower without the rear  
cover securely in place.  
Storage Procedure  
Refer to the Engine Owner’s Manual for directions regarding  
engine storage preparations. Prepare the mower for “end of  
season” storage as follows:  
1. Drain the fuel from the fuel tank and let the engine run  
until all fuel is out of the carburetor.  
2. Disconnect and remove the spark plug wire away from  
the spark plug before any other preparations are made!  
3. Tape all openings closed to prevent spraying water into  
the exhaust or air intakes during washing.  
4. Tilt the mower up on its rear wheels and thoroughly  
clean the underside of the deck. Do not tilt the mower  
with the spark plug or carburetor down. Scrape away  
any accumulation of grass with a putty knife and/or  
wire brush.  
5. Lubricate all exposed metal with a light coating of oil to  
prevent corrosion.  
6. Carefully fold the handles, “flexing” the control cables to  
prevent cable damage.  
7. Store the mower in a shed or other dry area, protected  
from weather.  
10  
3. Remove the blade (B, Figure 16).  
WARNING  
!
!
DO NOT attempt any maintenance, adjustments or service  
with engine and blade running. STOP engine and blade.  
Disconnect spark plug wire and secure away from spark  
plug. Engine and components are HOT. Avoid serious  
burns, allow sufficient time for all components to cool.  
Wear heavy leather gloves when handling or working  
around cutting blades. Blades are extremely sharp and can  
cause severe injury.  
Make sure that  
blade hub is seated  
between flanges  
A
C
Mower Blade Replacement  
B
Standard Blade Wear Limit  
1. Inspect the blade (Figure 15) frequently for signs of  
excessive wear or damage:  
D
(A) New blade  
(B) Wear limit (notch starts)  
(C) Dangerous condition! Do not use on the mower!  
Replace with a new blade.  
E
Figure 16: Removing the mower blade  
4. Sharpen the blade on a grinding wheel at an angle of 22  
to 28 degrees (B, Figure 17). DO NOT sharpen the blade  
beyond the original cutting edge (A).  
5. Check blade for balance. If necessary, correct balance by  
grinding heavy end of blade.  
A
B
6. Reinstall blade (B, Figure 16). Note the correct  
assembly order:  
C
(A) Blade hub  
(B) Blade  
(C) Blade flange (facing up)  
(D) Cone washer (concave side up)  
(E) Capscrew  
7. Check torque of blade retaining cap screw.  
Recommended torque should be 40 ft. lbs.  
Figure 15: Mower blade wear limits  
Do not sharpen  
beyond original  
cutting edge  
22-280  
WARNING  
!
!
DO NOT use a cutting blade that shows signs of excessive  
wear or damage. Refer to the Section entitled “MOWER  
BLADE REPLACEMENT” for proper blade inspection and  
service procedures.  
B
Blade Sharpening  
1. Disconnect the spark plug wire and secure the end away  
from the plug.  
End view of  
blade assembly  
2. Tilt the mower up on its rear wheels. Do not tilt the  
mower with the spark plug or carburetor down.  
A
Important: Drain the fuel tank before tipping the mower. DO  
NOT tip the machine with the carburetor or spark plug down.  
Oil from the crankcase will saturate the air filter and cause  
the engine to be hard to start or not start at all. If  
contamination does occur, the air filter will have to be  
replaced.  
Figure 17: Sharpening the mower blade  
11  
3. Fully engage the lever, and measure the length of the  
extended spring. The overall spring length should  
increase by 0.020 – 0.025”.  
WARNING  
!
!
DO NOT attempt any maintenance, adjustments or service  
with engine and blade running. STOP engine and blade.  
Disconnect spark plug wire and secure away from spark  
plug. Engine and components are HOT. Avoid serious  
burns, allow sufficient time for all components to cool.  
4. To adjust spring extension:  
a. Disengage the lever.  
b. To increase (+) the extended spring length, loosen  
the jam nut (B, Figure 20) and rotate the ferrule (C)  
below the adjustment turnbuckle (A), located on the  
lower end of the wheel drive control cable, one-half  
turn out from the turnbuckle. Tighten the jam nut.  
c. To decrease (-) the extended spring length, loosen  
the jam nut, and rotate the ferrule one-half turn in  
toward the turnbuckle. Tighten the jam nut.  
5. Engage the lever and recheck the extended spring  
length. Repeat Step 4 as needed.  
Wheel Drive Control Adjustment  
The wheel drive control lever (A, Figure 18) should engage  
the transmission when the lever is squeezed back toward the  
handlebar, and should disengage the transmission when the  
lever is released.  
B
A
+
C
A
-
Figure 18: Wheel drive controls  
(Components removed for clarity)  
If the transmission does not engage or disengage,  
adjustment may be performed as follows:  
Figure 20: Adjusting the transmission spring tension  
1. Remove the rear cover from the mower. Refer to the  
section entitled “Rear Cover Removal & Installation”.  
2. With the wheel drive control lever in the ‘DISENGAGE’  
position, the spring (A, Figure 19) on the end of the  
wheel drive control cable should have no tension.  
Measure the overall length of the unextended spring (B).  
IMPORTANT: INCORRECT ADJUSTMENT CAN CAUSE  
PREMATURE WEAR AND/OR DAMAGE TO THE WHEEL  
DRIVE COMPONENTS.  
A
B
Figure 19: Measuring the disengaged transmission spring  
length  
12  
Engine Drive Belt Replacement  
1. Empty the fuel tank.  
2. Remove the blade (A, Figure 21). Refer to the Section  
entitled “Blade Sharpening”.  
3. Remove the hardware (B) securing the two-piece belt  
cover beneath the deck. Remove the cover.  
4. Remove the rear cover of the mower. Refer to the Section  
entitled “Rear Cover Removal & Installation”.  
5. To replace the belt:  
a. Remove the hardware (B, Figure 22) securing the belt  
guide (A) to the transmission assembly. Remove the  
belt guide.  
b. Remove the belt from the transmission and engine  
pulleys, noting the belt routing.  
c. Replace the belt.  
d. Replace the belt guide onto the transmission.  
6. Replace the covers and blade.  
WARNING  
!
!
DO NOT attempt any maintenance, adjustments or service  
with engine and blade running. STOP engine and blade.  
Disconnect spark plug wire and secure away from spark  
plug. Engine and components are HOT. Avoid serious  
burns, allow sufficient time for all components to cool.  
Belt Service  
On self-propelled mowers, the engine belt transmits power  
from the engine to the transmission that powers the rear  
wheels. Should the belt become worn, it could cause slip-  
page, which would impair mower performance. The condi-  
tion of the engine belt should be checked after every 25  
hours of mower operation.  
Note: Recommended blade torque is 40 ft. lbs.  
A
B
A
B
Figure 22: Removing the belt guide  
Figure 21: Removing the blade and belt cover  
13  
Battery Testing  
WARNING  
!
!
Check the battery’s state of charge using a voltmeter.  
Remember to hook the positive lead to the battery’s positive  
terminal, and the negative lead to the negative terminal.  
Check the reading against the chart below. If the voltage  
reads less than 12.80 volts, charge the battery. Refer to the  
Section entitled “Battery Charging”.  
DO NOT attempt any maintenance, adjustments or service  
with engine and blade running. STOP engine and blade.  
Disconnect spark plug wire and secure away from spark  
plug. Engine and components are HOT. Avoid serious  
burns, allow sufficient time for all components to cool.  
Battery Condition  
Battery Service  
State of Charge  
100% Charged  
75% Charged  
50% Charged  
25% Charged  
0% Charged  
Digital Voltmeter  
12.80v  
New Battery Preparation  
1. Remove the battery from the carton.  
2. Place the battery in a well ventilated area on a level  
non-concrete surface.  
12.40v  
12.10v  
3. Test the battery. Refer to the Section entitled “Battery  
Testing”. If the battery needs charging, charge the  
battery. Refer to the Section entitled “Battery Charging”.  
4. Connect the positive (+) lead (red) first, from the battery  
harness to the positive terminal (+) on the battery using  
the bolt and nut plate supplied with the battery. Connect  
the negative (-) lead (black) last, to the negative terminal  
(-) on the battery using the bolt and nut plate. Apply a  
small amount of grease over the terminals to prevent  
corrosion.  
11.90v  
Less than 11.80v  
Battery Charging  
To charge the battery:  
1. With the supplied DC charger: Plug the charger  
connector into the battery harness connector (B, Figure  
23). Plug the charger into a wall outlet and charge the  
battery for 48 hours. (Longer periods will not damage  
the battery.)  
NOTE: The battery may come with the harness already  
connected. If so, simply check to be sure the terminal  
hardware is securely tightened.  
5. Install the battery onto the power unit.  
6. Plug the main harness connector (A, Figure 23) into the  
battery harness connector (B).  
!
WARNING  
!
Shield the positive terminal with terminal cover located on  
battery harness. This prevents metal from touching the  
positive terminal, which could cause sparks.  
Battery Service  
B
1. Test the battery. Refer to the Section entitled “Battery  
Testing”. If the battery needs charging, charge the  
battery. Refer to the Section entitled “Battery Charging”.  
3. If the battery will not accept a charge or is partially  
charged after charging per instructions, replace with a  
new battery.  
A
Figure 23: Battery connections  
!
WARNING  
!
Keep all sparks, flame and fire away from area when  
charging battery or when handling battery. Never use  
“BOOST” chargers on the battery.  
Battery Storage  
If the mower is to be stored out of season on its rear  
bumper, it is recommended the battery be removed, charged  
and stored.  
1. Remove the battery.  
2. Perform battery service. Refer to the Section entitled  
“Battery Service”.  
3. Store the battery in an area away from the mower on a  
wood surface.  
NOTE: Do not store the battery on a concrete surface.  
14  
WARNING  
!
!
DO NOT attempt any maintenance, adjustments or service  
with engine and blade running. STOP engine and blade.  
Disconnect spark plug wire and secure away from spark  
plug. Engine and components are HOT. Avoid serious  
burns, allow sufficient time for all components to cool.  
Rear Cover Removal and Installation  
To Remove the Rear Cover  
1. Remove the three fasteners (A, Figure 24) securing the  
rear apron to the machine.  
2. Remove the two fasteners (B) securing the rear cover to  
the machine.  
3. Slide the cover (C) down and out to remove. Set all  
components aside.  
To Install the Rear Cover  
1. Reverse steps 1-3 above, making sure the tab (D) on the  
rear cover is located on the outside of the machine.  
D
C
B
A
Figure 24: Removing the rear cover  
15  
Service Schedule  
ITEM  
SERVICE  
PERFORMED  
REF.  
EACH  
USE  
5
HRS  
25  
HRS  
50  
HRS  
100  
HRS  
EACH  
SEASON  
Engine Oil  
Check Oil Level  
Page 5  
Page 9  
X
Initial Oil Change  
X
Periodic Oil Change  
Clean Sponge Element  
Clean or Replace  
Replace  
Page 9  
X*  
Air Pre-Cleaner  
Air Cleaner  
Engine Manual  
Engine Manual  
Engine Manual  
Engine Manual  
X**  
X**  
Spark Plug  
X
Engine Cooling  
System  
Clean Shroud & Fins  
X**  
Drive Belt  
Check for Wear and  
Tension  
Page 9, 13  
Page 9, 11  
X
X
X
Mower Blade  
Check for wear, Damage  
& Replacement  
X
X
Mower Deck  
Clean Debris  
Accumulation  
Page 5  
Wheel Drive  
Components  
Clean Debris  
Accumulation; Check for  
Wear or Damage  
Page 10  
X
X
Transmission Cable  
Spring Adjustment  
Check & Adjust  
Page 12  
X
X
*Change oil every 25 hours when operating under heavy load or high temperatures.  
**Clean more often under dusty conditions or when air debris is present.  
Maintenance/Replacement Parts  
Blade Control Cable (SPV21675FC)  
Blade Control Cable (SPV21675EFC)  
Wheel Drive Control Cable  
Cutter Blade (Double Wave)  
Drive Belt  
7101399  
7101400  
7101398  
7100242  
7100883  
7102346  
Parts Manual for Snapper 21” Variable Speed Walk Behind Mower  
16  
Troubleshooting  
PROBLEM  
PROBABLE CAUSE  
CORRECTIVE ACTION  
1. Fill fuel tank with fresh fuel.  
Engine Will Not Start 1. Fuel tank empty.  
Using Recoil Starter  
2. Engine needs priming.  
3. Spark plug wire disconnected.  
2. Prime. Check Engine Manual for Instructions.  
3. Place spark plug wire onto spark plug.  
1. Fill fuel tank with fresh fuel.  
Engine Will Not Start 1. Fuel tank empty.  
(Electric Start Models)  
2. Engine needs priming.  
3. Spark plug wire disconnected.  
4. Wiring harness disconnected.  
5. Battery dead.  
2. Prime. Check Engine Manual for Instructions.  
3. Place spark plug wire onto spark plug.  
4. Connect wiring harness.  
5. Charge or replace battery.  
Engine Stalls or Stops 1. Blade control is released or is not being held 1. Blade control should be held securely against  
After Running  
securely against handle.  
2. Fuel tank empty.  
handle at all times during operation of mower.  
2. Fill with fuel to proper level.  
3. Engine air pre-cleaner and or air cleaner dirty. 3. Clean free of all debris.  
4. Spark plug defective or gap set improperly.  
5. Water, debris or stale fuel in fuel system.  
Engine Loses Power 1. Engine air pre-cleaner or air cleaner dirty.  
2. Spark plug faulty.  
4. Service spark plug.  
5. Drain and clean fuel system.  
1. Clean or replace filters.  
2. Service spark plug.  
3. Water, debris or stale fuel in fuel system.  
3. Drain and clean fuel system.  
Excessive Vibration 1. Damaged, out of balance or bent mower blade. 1. Service mower blade.  
2. Loose blade components.  
3. Loose or missing air lift (if equipped).  
4. Lumpy or frayed belt.  
2. Service and tighten loose parts.  
3. Replace air lifts. Tighten to proper torque.  
4. Replace belt.  
Mower Will Not Move 1. Build-up of debris on or around wheel drive 1. Clean debris.  
Loss Of Traction  
components.  
2. Transmission cable adjustment required.  
2. Adjust transmission cable.  
3. Replace drive belt.  
4. Contact authorized SNAPPER dealer.  
1. Adjust transmission cable.  
2. Contact authorized SNAPPER dealer.  
3. Drive belt requires replacement.  
4. Damaged transmission.  
Transmission Noise 1. Transmission cable adjustment required.  
2. Damaged transmission.  
Ground Speed  
1. Build-up of debris on or around wheel drive 1. Clean debris.  
Too Fast / Too Slow; control components.  
2. Transmission cable adjustment required.  
2. Adjust transmission cable.  
3. Replace drive belt.  
4. Contact authorized SNAPPER dealer.  
1. Adjust cutting height.  
2. Adjust to a slower speed.  
3. Sharpen cutting edges or replace blade.  
1. Adjust to a slower speed.  
2. Mow when grass is dry.  
3. Service mower blade.  
Unable to Adjust  
Ground Speed  
3. Drive belt requires replacement.  
4. Damaged transmission.  
Cutting Grass Improperly1. Cutting height too low or high.  
2. Forward speed too fast.  
3. Cutting blade dull or damaged.  
Poor Grass Discharge 1. Forward speed too fast.  
2. Grass is wet.  
3. Excessively worn or damaged blade.  
4. Build up of grass clippings and debris under 4. Clean deck.  
deck.  
5. Improper blade installed on deck.  
5. Install proper SNAPPER blade.  
6. Install blade properly.  
1. Contact authorized SNAPPER dealer.  
2. Check and tighten drain plug.  
3. Make sure dip stick or oil filler cap is securely in  
place.  
6. Blade installed improperly on deck.  
1. Leaking engine case.  
Oil Leaking  
17  
2 YEAR LIMITED WARRANTY  
For two (2) years from purchase date for the original purchaser’s residential, non-commercial use, SNAPPER, through any  
authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon  
examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.  
For ninety (90) days from purchase date for the original purchaser’s commercial, rental, or other non-residential use, SNAP-  
PER, through any authorized SNAPPER dealer will replace, free of charge, any part or parts found upon examination by the  
factory at McDonough, Georgia, to be defective in material or workmanship or both.  
All transportation costs incurred by the purchaser in submitting material to an authorized SNAPPER dealer for replacement  
under this warranty must be paid by the purchaser.  
This warranty does not apply to certain transmissions, to engines and their components, and batteries, as these items are war-  
ranted separately. This warranty does not apply to parts that have been damaged by accident, alteration, abuse, improper  
lubrication, normal wear, or other cause beyond the control of SNAPPER. This warranty does not cover any machine or com-  
ponent part that has been altered or modified changing safety, performance, or durability.  
Batteries have a one (1) year warranty period with free replacement if required for one (1) year from the original purchase  
date. SNAPPER will not be responsible for any installation cost incurred. The battery warranty only covers original equipment  
batteries and does not cover damage to the battery or machine caused by neglect or abuse, destruction by fire, explosion,  
freezing, overcharging, improper maintenance, or use of improper electrolyte.  
There is no other express warranty.  
DISCLAIMER OF WARRANTY  
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to two (2) years  
from purchase date for the original purchaser’s residential or other non-commercial use, and ninety (90) days from pur-  
chase for the original purchaser’s commercial, rental or other non-residential use, and to the extent permitted by law, any  
and all implied warranties are excluded. This is the exclusive remedy. Liabilities for consequential damages, under any  
and all warranties are excluded.  
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of  
incidental or consequential damages, so the above limitation or exclusion may not apply to you.  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
WARNING: THE USE OF REPLACEMENT PARTS OTHER THAN GENUINE SNAPPER PARTS MAY IMPAIR THE SAFETY OF  
SNAPPER PRODUCTS AND WILL VOID ANY LIABILITY AND WARRANTY BY SNAPPER ASSOCIATED WITH THE USE OF  
SUCH PARTS.  
IMPORTANT:  
Please fill out the attached SNAPPER Product Registration Card immediately and mail to:  
Snapper’s Product Registration Center, P.O. Box 1379, McDonough, Georgia 30253  
18  
19  
Notes  
20  
Notes  
21  
21” VARIABLE SPEED  
REAR DISCHARGE  
WALK BEHIND  
MOWERS  
Product Specifications (All)  
Common Service Parts  
Part Number  
Deck Size (in)  
Height of Cut (in)  
21  
1.25 - 4  
Variable Speed/Gear  
Blade Control Cable (SPV21675FC)  
Blade Control Cable (SPV21675EFC)  
Wheel Drive Control Cable  
Cutter Blade (Double Wave)  
Drive Belt  
7101399  
7101400  
7101398  
7100242  
7100883  
7102346  
Transmission Type  
Ground Speed (mph)  
Engine Power (ft-lbs)  
Engine Displacement (cc)  
Fuel Tank Capacity (qt)  
0 - 4.2  
6.75  
190  
Parts Manual  
1.6  
Engine Power Rating Information: The gross power rating for individual gas engine models is labeled in accordance with  
SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating perform-  
ance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060  
RPM; horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among other  
things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines  
are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the  
rated gross power when used in a given piece of power equipment (actual "on-site" or net horsepower). This difference is due  
to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump,  
etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability.  
Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this  
Series engine.  
Snapper Products  
535 Macon Street  
McDonough, GA 30253  
1-800-317-7833  
22  

Agri Fab Lawn Aerator 45 03431 User Manual
Craftsman Lawn Mower 24728980 User Guide
Dixon Lawn Mower 966038601 User Guide
Land Pride Lawn Mower ZSR60 User Guide
McCulloch Lawn Mower M13597RB User Guide
Poulan Lawn Mower 184617 User Guide
Snapper Lawn Aerator 3882 User Manual
Snapper Lawn Mower 1691003 User Guide
Snapper Lawn Mower P21400 User Manual
Snapper Lawn Mower R2167517BV User Manual