Scag Power Equipment Lawn Mower GC STC CS User Guide

MODEL GC-STC-CS  
THIS MANUALCONTAINS THE OPERATING  
INSTRUCTIONS AND SAFETY INFORMA-  
TION FORYOUR SCAGACCESSORY. READ-  
ING THIS MANUAL WILL PROVIDE YOU  
WITH MAINTENANCE AND ADJUSTMENT  
PROCEDURES TO KEEPYOURACCESSORY  
PERFORMING TO MAXIMUM EFFICIENCY.  
THE SPECIFIC MODELS THAT THIS BOOK  
COVERS ARE CONTAINED ON THE INSIDE  
COVER. BEFORE OPERATING YOUR MA-  
CHINE, PLEASE READ ALL THE INFORMA-  
TION ENCLOSED.  
PART NUMBER 03156  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A replacement manual is available from your  
authorized Scag Service Dealer or by contacting:  
Scag Power Equipment, Service Department at P.O.  
Box 152, Mayville, WI 53050. You may also contact  
manual for this grass catcher can be downloaded by  
using the model and serial number or use the contact  
form to make your request. Please indicate the  
complete model and serial number of your Scag  
product when requesting replacement manuals.  
1.1 INTRODUCTION  
This manual has been prepared to provide the  
information you need to correctly assemble, operate,  
and maintain this grass catcher. Read it carefully and  
keep it for future reference.  
The replacement of any part on this product by other  
than the manufacturer's authorized replacement part  
may adversely affect the performance, durability or  
safety of this product.  
USE OF OTHER THAN ORIGINAL SCAG  
REPLACEMENT PARTS WILL VOID THE  
WARRANTY.  
WARNING  
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING  
KIT, OR ENTIRE GRASS CATCHER INSTALLED  
If additional information or service is needed that is  
not outlined in this manual, please contact your Scag  
Power Equipment dealer. Scag dealers are trained in  
the latest service methods and carry a full line of Scag  
replacement parts.  
2. Before removing the grass bags, disengage the  
mower, stop the engine and wait for all  
movement to stop.  
3. ALWAYS turn the engine OFF, remove the key  
and wait for all movement to stop before  
servicing or cleaning the mower or the grass  
catcher.  
When ordering parts, always provide the complete  
model number of your catcher.  
All information provided in this manual is based upon  
information available at the time of printing. Scag  
Power Equipment reserves the right to make changes  
at any time without notice or obligation.  
DANGER  
ROTATING BLOWER  
BLADES  
1.2 DIRECTION REFERENCE  
STOP ENGINE BEFORE  
ENTERING CHUTE  
The "Right" and "Left", "Front" and "Rear" of the  
machine are referenced from the normal operating  
position.  
CONTACT CAN INJURE  
4. Do not modify or alter any component of the  
grass catcher attachment or mower.  
2.1 SAFETY AND OPERATING  
INSTRUCTIONS  
5. Do not allow any passengers to ride on the grass  
catcher attachment or on the mower.  
-NOTE-  
To avoid personal injury, it is imperative that all  
safety instructions be observed.  
2.2 GRASS CATCHING OPERATION  
1. Read this operator's manual and the  
operator's manual that is supplied with the  
machine this attachment is used on.  
1. With the hopper door closed, engage the deck  
drive.  
2. Proceed to mow until the hopper is full.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. To clean the hopper debris screen;  
3. When dumping the hopper into a disposal area:  
A. Disengage the deck drive and allow all  
moving parts to come to a complete stop.  
WARNING  
DO NOT DUMP CLIPPINGS IN A DISPOSAL AREA THAT IS  
BURNING  
B. Apply parking brake and shut off the engine.  
A. Disengage the deck drive, apply the parking  
brake and allow all moving parts to come to  
a complete stop.  
C. Stand on the left side of the hopper  
assembly.  
D. Unhook the debris screen latches and  
remove the debris screen from the hopper.  
See Figure 2-3.  
B. Pull downward on the hopper door handle to  
allow the hopper sweeper to remove the  
material from inside the hopper. See Figure  
2-1.  
Debris Screen  
Latches  
Figure 2-3 GC-CS  
Figure 2-1 GC-CS  
FIGURE 2-3  
FIGURE 2-1  
E. Remove material from the debris screen and  
reinstall. Secure by latching the debris  
screen latches.  
C. Once the material has been completely  
removed from the hopper, lift the hopper  
door handle to close the hopper door and  
lock into place. See Figure 2-2.  
6. When service is needed inside the hopper,  
disengage the deck drive and allow all moving  
parts to come to a complete stop, shut off the  
engine and apply the parking brake. Rotate the  
hopper door prop rod upward until it contacts the  
hopper door. This will prevent the hopper door  
from moving until the service is complete. See  
Figure 2-4.  
LOCK  
Figure 2-2 GC-CS  
FIGURE 2-2  
Hopper Prop  
Rod  
4. When dumping the hopper into a disposal area,  
inspect the hopper debris screen for material.  
When the debris screen is full of material, the  
grass catching ability may suffer. Frequency of  
cleaning the hopper debris screen will vary  
dependingonconditions.  
Figure 2-4 GC-CS  
FIGURE 2-4  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.1 ASSEMBLY INSTRUCTIONS FOR 48"  
AND 52" CUTTER DECK  
-NOTE-  
When installing this grass catcher on a machine  
with a serial number range from 7630001 to  
8479999, you will need to install part number  
461764 for a 48" cutter deck or 461765 for a  
52" cutter deck. This kit includes a new Turbo  
Baffle and Deck Baffle.  
-NOTE-  
Use the illustrated parts list as a part number  
reference when following the assembly  
instructions.  
1. Remove all packaging materials. Lay out the  
mounting hardware and the catcher assembly  
parts for easy access. Prepare the work area  
making sure that it is a clean, safe environment.  
4. Install the grass catcher pulley onto the spindle  
assembly. Apply loctite to both pulley setscrews  
and tighten. See Figure 3-1.  
5. Install the blower mounting bracket to the deck  
using carriage bolts (p/n 04003-11), lockwashers,  
and nuts. Do not fully tighten the hardware at  
this time. See Figure 3-2, Page 4.  
WARNING  
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING  
KIT, OR ENTIRE GRASS CATCHER INSTALLED  
2. Remove the discharge chute from the cutter  
deck. See Figure 3-1.  
6. Install the blower assembly to the mounting  
bracket and secure with the mounting pin.  
See Figure 3-3, Page 4.  
-NOTE-  
Do not discard the discharge chute or  
mounting hardware. The discharge chute  
MUST be reinstalled anytime the grass  
catcher is removed from the machine.  
7. Align the blower assembly with the discharge  
opening of the cutter deck. Tighten the hardware  
for the mounting bracket. Then tighten the  
hardware for the catch plate. See Figure 3-3,  
Page 4.  
3. Remove the right side belt cover to gain access to  
the spindle assembly. Remove the front u-nut  
from the cutter deck bracket. See Figure 3-1.  
8. Install the large hair pin through the rear hole in  
the discharge chute mounting bracket. See  
Figure 3-3, Page 4.  
-NOTE-  
9. Install the belt to the spindle pulley. When  
replacing the belt, see figure below.  
Retain the original belt cover. This cover  
MUST be reinstalled anytime the  
complete catcher system is removed.  
BACK SIDE  
IDLER PULLEY  
BLOWER  
REMOVE DISCHARGE  
CHUTE AND  
HARDWARE  
INSTALL PULLEY  
ON RH SPINDLE SHAFT -  
ON TOP OF EXISTING  
SPINDLE DRIVE  
PULLEY  
REMOVE EXISTING  
RT. SIDE BELT  
COVER  
PULLEY  
REMOVE U-NUT  
RIGHT SIDE OF  
CUTTER DECK SHOWN  
SPINDLE  
PULLEY  
FRONT SIDE  
IDLER PULLEY  
(Note: Some parts not shown for viewing purposes.)  
Figure 1- GC-STC install art  
FIGURE 3-1  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
FLATWASHER  
ELASTIC STOP  
NUT  
CARRIAGE BOLT  
FIGURE 3-2  
BLOWER  
ASSEMBLY  
HAIR  
PIN  
MOUNTING  
BRACKET  
TIGHTEN  
CATCH PLATE  
HARDWARE  
PROPERYL  
SECREVI  
ENGEI  
WTHI  
OLI  
AND  
FUEL.  
MOUNTING PIN  
TIGHTEN MOUNTING  
BRACKET HARDWARE  
RIGHT SIDE OF  
CUTTER DECK SHOWN  
(Note: Some parts not shown for viewing purposes.)  
2005 GC-STC install art 3  
FIGURE 3-3  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Install the new belt covers and secure. See  
items number 1 and number 21 on page 10 of the  
Blower Mounting Components section in the  
Illustrated Parts List for proper installation.  
-NOTE-  
The hopper dump handle can be installed on  
either side for operator convenience. When  
installing this grass catcher on a machine  
with the Roll Over Protection System (ROPS),  
the curved handle will need to be installed on  
the right side.  
11. Install the hopper mounting brackets to the  
outside of the frame on the rear of the machine.  
See Figure 3-4.  
13. Install the hose from the blower assembly  
adapter to the hopper hood and secure using the  
6-1/2"clamps.  
Hopper  
Mounting  
Brackets  
14. Using the weight support bar as a guide, identify  
the four corresponding mounting holes, and the  
existing hardware that will need to be removed  
in order to secure the weight support bar to the  
front of the machine as shown. See Figure 3-6.  
Rear Frame  
Figure  
4
A
GC-STT Install Art  
FIGURE 3-4  
15. Install one 7/16-14 x 1-3/4" hex head bolt into  
each of the four mounting holes in the weight  
support bar, and through the matching holes in  
the caster support weldment. Secure this  
assembly to the front of the machine using the  
7/16- .5" x 1-1/4" x .083" flatwashers, and the  
7/16-14 elastic stop nuts. Torque hardware to  
59 ft. lbs. See Figure 3-6.  
12. With help from an assistant, install the hopper  
assembly to the machine by installing the  
mounting post into the hopper mounting brackets  
and secure with the ring pins. Tighten the bolts  
and jam nuts. See Figure 3-5.  
FIGURE 3-6  
16. Operate and test.  
Locking  
Bolts  
Ring Pins  
Locking  
Bolts  
Ring Pins  
FIGURE 3-5  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
4.1 GRASS CATCHER REMOVAL  
INSTRUCTIONS  
5. With help from an assistant, remove the hopper  
assembly from the mounting posts.  
1. Prepare the work area making sure that it is a  
clean, safe environment.  
2. Remove the rubber strap holding the adapter to  
the blower assembly. See Figure 4-1.  
WARNING  
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING  
KIT, OR ENTIRE GRASS CATCHER INSTALLED  
3. Remove the pin and hair pin holding the blower  
assembly to the mounting bracket on the cutter  
deck and remove the blower assembly. See  
Figure 4-1.  
6. Re-install the side discharge chute to the opening  
on the cutter deck. Replace the two outside  
mounting bolts on the discharge chute with the  
clevis pins (p/n 04064-15) and rue cotter pins  
(p/n 04069-03). See Figure 4-3.  
ADAPTER  
HAIR  
PIN  
BLOWER  
ASSEMBLY  
MOUNTING  
BRACKET  
DISCHARGE  
CHUTE  
CLEVIS PIN  
P/N 04064-15  
PIN  
CLEVIS PIN  
P/N 04064-15  
RUE COTTER PIN  
P/N 04069-03  
RIGHT SIDE OF  
CUTTER DECK SHOWN  
GC-STC removal art 3  
2004 GC-STC removal art 1  
(Note: Some parts not shown for viewing purposes.)  
FIGURE 4-3  
FIGURE 4-1  
4. Loosen the four (4) locking bolts and jam nuts.  
Remove the two (2) pins holding the hopper  
assembly to the mounting posts on the rear of the  
machine. See Figure 4-2.  
Loosen  
Locking  
Remove  
Bolts  
Mounting  
Pins  
Loosen  
Locking  
Bolts  
Remove  
Mounting  
Pins  
2005 GC-STC removal art 2-A  
FIGURE 4-2  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STC 48" & 52" BLOWER HOUSING ASSEMBLY  
9
48  
10  
11  
12  
13  
2
4
8
1
9
5
6
3
11  
7
10  
10  
14  
44  
47  
27  
14  
11  
12  
15  
43  
42  
41  
16  
14  
15  
17  
26  
28  
17  
39  
40  
18  
34  
27  
19  
25  
20  
21  
41  
38  
22  
23  
3
35  
27  
51  
24  
14  
46  
R
D
O
T
Stop T  
A
A
N
eng  
I
24  
14  
N
G
G
ine be  
E
R
B
DO  
L
U
D
A
D
N
N
O
ISC  
LE  
fore cl  
eaEning  
or  
H
SS  
T
O
A
S
R
G
P
GE  
ER  
A
N
D
R
A
G
ATE  
S
UA  
S
C
M
O
W
R
A
TC  
B
rem  
D
IS  
L
O
H
IN  
E
ER  
O
o
vin  
R
W
S
TA  
g
E
R
L
R
L
ED  
29  
50  
30  
33  
32  
37  
31  
31  
45  
47  
2005 GC Blower Assembly  
45  
35 34  
49  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STC 48" & 52" BLOWER HOUSING ASSEMBLY  
Ref.  
No.  
Part  
Number  
Ref.  
No.  
Part  
Number  
Description  
Description  
1
2
3
4
5
6
7
8
04067-07  
481547  
04019-02  
04001-59  
04001-01  
423298  
481428  
482300  
04024-02  
04021-05  
04041-07  
43277  
Pin, Ring 2-1/4" Long  
Lanyard, Deck Height Pin  
Nut, Serr. Flange 1/4-20  
Bolt, Hex Head 1/4-20 x 1-1/4"  
Bolt, Hex Head 1/4-20 x 3/4"  
Belt Cover, Rear  
Grip, Blower Lever  
Cap, Square  
Nut, Push On 3/8 Thread  
Lock Nut, 3/8-16  
Flatwasher, 3/8-.391 x .938 x .105  
Spacer  
Pulley, Idler 4" Dia.  
Nut, Elastic Stop 3/8-16  
Lockwasher, 3/8-16  
Plate, Catch Mounting  
Bolt, Carr. 3/8-16 x 1-1/2"  
Bolt, Hex Head 3/8-16 x 3" - 52"  
Bolt, Hex Head 3/8-16 x 2-1/4" - 61"  
Bolt, Hex Head 3/8-16 x 3-1/2"  
Bolt, Hex Head 3/8-16 x 1-3/4"  
Idler Arm Assembly  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
04019-04  
Nut, Serr. Flange 3/8-16  
04001-136 Bolt, Hex Head 3/8-16 x 1-1/2 Gr. 8  
481377  
461681  
04003-12  
04063-06  
451683  
483034  
04021-10  
04040-04  
421319  
48136-02  
48135-09  
482298  
04012-04  
451655  
481522  
43212  
04019-03  
461723  
424094  
04062-05  
461680  
482080  
481377  
Decal, Danger  
Blower Housing Assembly  
Bolt, Carr. 5/16-18 x 3/4" Gr. 5  
Key, 1/4 x 1/4 x 1-1/2"  
Fan Weldment  
Bearing Assembly  
9
Nut, Elastic Stop 5/16-18  
Flatwasher, 5/16-.344 x .688 x .065  
Cover, Blower Housing  
Clamp, 8-5/8" Max Dia.  
Hose, 8.00" Dia. x 53" Long  
Pulley, 4-3/4" O.D. - 1" Bore  
Set Screw, 5/16-18 x 3/8"  
Frame, Blower Mount  
Spring, Main Drive  
10  
11  
12  
13  
14  
15  
16  
17  
18  
482299  
04021-09  
04030-04  
423933  
04003-05  
04001-54  
04001-46  
04001-81  
04001-21  
461812  
482278  
482079  
04043-04  
43575  
481039  
Spacer  
Nut, Serr. Flange 5/16-18  
Adapter w/Strap  
19  
20  
21  
22  
23  
24  
25  
26  
Plate, Blower Catch  
Hair Pin Cotter, .243 x 4"  
Blower Housing Assembly, GC-STT  
Decal, Rotating Blower  
Decal, Blower  
Belt, GC-STC  
Pulley, 3" O.D., GC-STC  
Washer, 3/8 Hardened  
Pivot, Idler  
Decal, Belt Cover  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STC 48" & 52" BLOWER MOUNTING COMPONENTS  
FOR MACHINES WITH A SERIAL  
NUMBER BETWEEN  
7630001 - 8479999  
ONLY  
31  
30  
24  
10  
23  
25  
25  
6
5
26  
10  
26  
11  
29  
27  
2
28  
4
32  
6
7
1
8
29  
27  
3
28  
6
9
UNDER SIDE OF  
CUTTER DECK SHOWN  
13  
12  
21  
14  
15  
15  
22  
20  
16  
18  
17  
19  
RIGHT SIDE OF  
CUTTER DECK SHOWN  
390STC203B  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STC 48" & 52" BLOWER MOUNTING COMPONENTS  
Ref. Part  
No.  
Number  
Description  
1
482612  
Belt Cover, GC-STC  
2
3
04029-04  
482300  
Wingnut, Plastic 3/8" Small  
Cap, Square Vinyl  
4
5
6
7
8
9
04021-08  
461723  
Nut, Elastic Stop 1/4-20  
Adapter, Blower GC-STC, includes item #7  
Flatwasher, 1/4-.312 x .750 x .065  
Rubber Strap 7-3/4"  
Bolt, Hex Head 1/4-20 x 1-1/4"  
Knob W/Stud, 3/8-16 x 1-1/4"  
Clevis Pin, 5/16 x 1-1/2"  
Pin, Rue Cotter 5/16 Dia.  
Pin, Ring 1/2 x 2-1/4"  
04040-14  
48137-04  
04001-59  
481625-01  
04064-15  
04069-03  
04067-07  
481547  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
Lanyard  
482587  
Pulley, 4.0" Dia. 1.125 Bore  
Setscrew, 5/16-18 x 3/8"  
Nut, Elastic Stop 3/8-16  
Lockwasher, 3/8"  
Flatwasher, 3/8-.391 x .938 x .105  
Bolt, Carr. 3/8-16 x 1-1/4" Grade 5  
Mounting Post Weldment, Blower  
Belt Cover  
04012-04  
04021-09  
04030-04  
04041-07  
04003-11  
451693  
423708  
04110-03  
04017-05  
04003-23  
04021-09  
04041-07  
04001-09  
04040-15  
04021-10  
04019-02  
423633  
U-Nut  
Bolt, Hex Head 1/4-20 x 3/4"  
Bolt, Carriage 3/8-16 x 1"  
Nut, Elastic Stop 3/8-16  
Flatwasher, 3/8-.391 x .938 x .105  
Bolt, Hex Head 5/16-18 x 1"  
Flatwasher, 5/16-.375 x .875 x .083  
Nut, Elastic Stop 5/16-18  
Nut, Serrated Flange 1/4-20  
Baffle, 48"  
423629  
Baffle, 52"  
32  
423955  
423956  
Baffle, Turbo 48" Deck  
Baffle, Turbo 52" Deck  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STC-CS HOPPER COMPONENTS  
16  
14  
49  
50  
5
4
3
45  
45  
41  
15  
31  
43  
11  
51  
17  
56  
55  
40  
58  
59  
8
12  
9
25  
29  
6
33  
37  
34  
10  
53  
2
50  
49  
34  
B
49  
42  
24  
55  
27  
43  
49  
6
53  
61  
48  
60  
36  
18  
38  
63  
19  
53 C  
49  
34  
12  
49  
50  
52  
20  
54  
41  
49  
66  
65  
49  
18  
24  
49  
53  
53  
60  
7
70  
A
61  
62  
58  
33  
59  
28  
1
49  
64  
21  
10  
34  
38  
32  
49  
69  
30  
49  
45  
49  
63  
38  
35  
46  
22  
49  
37  
13  
33  
36  
25  
49  
57  
49  
21  
C
23  
33  
68  
44  
26  
38  
58  
32  
53  
40  
49  
20  
65  
B
59  
53  
64  
46  
33  
19  
66  
A
65  
67  
71  
71A  
57  
46  
58  
59  
29  
60  
28  
49  
49  
61  
49  
61  
35  
46  
26  
37  
37  
60  
2005 CSHOPPEREXPLOD-STC  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STC-CS HOPPER COMPONENTS  
Ref.  
No.  
Part  
Number  
Ref.  
No.  
Part  
Number  
Description  
Description  
1
2
3
4
5
6
7
8
461627  
482732  
461626  
482777  
04090-02  
423834  
423938  
423849  
423850  
423858  
423837  
423840  
451599  
451601  
451602  
451603  
451607  
43631  
423851  
423852  
422386  
423862  
423864  
43063  
43282  
43277  
481309  
43641  
43640  
Hopper, GC-STC-CS  
Door, GC-CS  
Sweeper Weldment, GC-CS  
Pad, Rubber  
Pop Rivet, 3/16 x .652  
Plate, Stiffener  
Support Frame, Hopper  
Hinge Bracket, L.H.  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
04001-77  
04003-04  
04010-01  
04017-16  
04017-17  
04019-03  
04019-04  
04020-12  
04021-01  
04021-09  
04021-10  
04032-01  
04040-15  
04041-07  
43642  
Bolt, Hex Head 3/8-16 x 3-1/2"  
Bolt, Carriage 5/16-18 x 1"  
Screw, #10-32 x 1/2"  
Cap Screw, 5/16-18 x 3/4" Serr. Flan.  
Cap Screw, 5/16-18 x 1" Serr. Flan.  
Nut, 5/16-18 Serrated Flange  
Nut, 3/8-16 Serrated Flange  
Nut, 3/8-16 UNC Jam  
Nut, #10-32 Elastic Stop  
Nut, 3/8-16 Elastic Stop  
Nut, 5/16-18 Elastic Stop  
Washer, Special Wave  
Washer, 5/16-.375 x .875 x .083 Flat  
Washer, 3/8-.931 x .938 x .105 Flat  
Bushing, Hopper Latch GC-CS  
Bolt, Hex Head 3/8-16 x 3"  
Hinge Weldment, Door  
9
Hinge Bracket, R.H.  
Bracket, Hopper Support  
Latch, Door Prop  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
Plate, Latch  
Bellcrank Weldment, Upper  
Debris Screen Weldment  
Screen Support Weldment, Rear  
Screen Support Weldment, Front  
Hinge Weldment, Hopper  
Spacer  
Brace Stiffener, Short  
Tube, Upright  
Brace, Engine Mount  
Latch, Dump Rod Inner  
Latch, Dump Rod Outer  
Spacer  
Spacer  
Spacer  
Latch, Hood  
Linkage Assembly, Lower  
Linkage Assembly, Upper  
Knob  
Bolt, Hex Head 5/16-18 x 1-1/4  
Bolt, Hex Head 3/8-16 x 3/4"  
Bolt, Hex Head 3/8-16 x 1"  
Bolt, Hex Head 3/8-16 x 1-1/2"  
Bolt, Hex Head 3/8-16 x 1-3/4"  
Bolt, Hex Head 3/8-16 x 1-1/4"  
Bolt, Hex Head 3/8-16 x 2"  
Bolt, Hex Head 3/8-16 x 2-1/4"  
Bolt, Hex Head 5/16-18 x 3-1/2"  
04001-54  
451598  
481547  
481538  
04020-26  
481539  
Lanyard  
Rod End Male, 3/8-24 L.H. Thread  
Nut, 3/8-24 UNF L.H. Thread  
Rod End Male, 3/8-24 R.H. Thread  
Nut, 3/8-24 UNF R.H. Thread  
Alignment Bracket, GC-CS  
Bolt, Hex Head 3/8-16 x 2-1/2"  
Lock Wasker, 3/8-16 Spring  
Nut, 3/8-16 UNC Zinc  
04020-25  
423865  
04001-31  
04030-04  
04020-04  
04021-05  
04001-12  
04012-10  
44147  
423855  
423859  
423836  
451726  
Nut, 3/8-16 Center Lock  
Bolt, Hex Head 5/16-18 1-3/4"  
Nut, 5/16-18 Elastic Stop (Not Shown)  
Rod, Dump Lever  
Bracket, Lower Stiffener  
Backing Plate, Hopper (Not Shown)  
Retainer Strip, Hopper  
481245  
04001-10  
04001-18  
04001-19  
04001-20  
04001-21  
04001-32  
04001-45  
04001-46  
04001-63  
68  
69  
70  
71  
71A  
Mounting Bracket Weldment, R.H.  
Mounting Bracket Weldment, L.H.  
451725  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GC-STC-CS DECALS  
481039  
482275  
481327  
481377  
483037  
483039  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY- COMMERCIAL ACCESSORY  
AnypartoftheScagcommercialaccessorymanufacturedbyScagandfound,inthereasonablejudgmentofScag,  
tobedefectiveinmaterialorworkmanship,willberepairedorreplacedbyanAuthorizedScagServiceDealerwithout  
charge for parts and labor.  
The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within  
the warranty period. The expense of delivering the accessory to the dealer for warranty work and the expense of  
returningitbacktotheownerafterrepairorreplacementwillbepaidforbytheowner. Scag’sresponsibilityinrespect  
toclaimsislimitedtomakingtherequiredrepairsorreplacements,andnoclaimofbreachofwarrantyshallbecause  
for cancellation or rescission of the contract of sale of any Scag machine. Proof of purchase will be required by the  
dealer to substantiate any warranty claim. All warranty work must be performed by an Authorized Scag Service  
Dealer.  
This warranty is limited to 90 days from the date of original retail purchase for any Scag accessory that is used for  
commercial purposes, or any other income-producing purpose including rental use.  
This warranty does not cover any accessory that has been subject to misuse, neglect, negligence, or accident, or  
thathasbeenoperatedinanywaycontrarytotheoperating instructionsasspecifiedintheOperator'sManual. The  
warranty does not apply to any damage to the accessory that is the result of improper maintenance, or to any  
accessory or parts that have not been assembled or installed as specified in the Operator's Manual.  
The warranty does not cover any accessory that has been altered or modified. In addition, the warranty does not  
extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable  
judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or  
durability. This warranty does not cover engines and electric starters, which are warranted separately by their  
manufacturer.  
ScagPowerEquipmentreservestherighttochangeorimprovethedesignofanyaccessorywithoutassumingany  
obligation to modify any accessory previously manufactured.  
All other implied warranties are limited in duration to the 90 day warranty period. Accordingly, any such implied  
warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety  
after the expiration of the appropriate ninety day warranty period. Scag’s obligation under this warranty is strictly  
andexclusivelylimitedtotherepairorreplacementofdefectivepartsandScagdoesnotassumeorauthorizeanyone  
toassumeanyotherobligationforthem. Somestatesdonotallowlimitationsonhowlonganimpliedwarrantylasts,  
so the above limitation may not apply to you.  
Scagassumesnoresponsibilityforincidental,consequentialorotherdamagesincluding,butnotlimitedto,expense  
forgasoline,oil,expenseofdeliveringthemachinetoanAuthorizedScagServiceDealerandexpenseofreturning  
it back to the owner, mechanic’s travel time, telephone or telegram charges, rental of a like product during the time  
warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of  
the mower, loss of time, or inconvenience. Some states do not allow the exclusion or limitation of incidental or  
consequential damages, so the above limitation or exclusion may not apply to you.  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© 2004  
PART NO. 03156  
PRINTED 8-2004  
PRINTED IN USA  
SCAG POWER EQUIPMENT  
DIVISION OF METALCRAFT OF MAYVILLE, INC  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Agri Fab Lawn Sweeper 45 0456 User Manual
Alamo Lawn Mower 02969111P User Manual
Alamo Lawn Mower A60 User Manual
Briggs Stratton Lawn Mower 15C100 User Manual
Cub Cadet Lawn Mower 186 407 100 User Guide
Cub Cadet Lawn Mower CC46ES User Guide
Dixon Lawn Mower SE 5225 KOH CE User Guide
Poulan Lawn Mower 183384 User Guide
Snapper Lawn Mower E281016BE User Manual
Snapper Lawn Mower NZM25523KWV User Manual