Land Pride Lawn Mower FDR3590 User Guide

Rear Discharge Grooming Mowers  
FDR3590  
15939  
310-229M  
Operator’s Manual  
Read the Operator’s manual entirely. When  
you see this symbol, the subsequent  
15939  
!
instructions and warnings are serious - follow  
without exception. Your life and the lives of  
others depend on it!  
© Copyright 2007 Printed  
12/10/07  
Cover photo may show optional equipment  
not supplied with standard unit.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Land Pride  
Important Safety Information  
Important Safety Information  
These are common practices that may or may not be applicable to the products described in  
this manual.  
Safety at All Times  
Look For The Safety Alert Symbol  
Thoroughly read and understand  
the instructions given in this  
manual before operation. Refer to  
the “Safety Label” section, read  
all instructions noted on them.  
The SAFETY ALERT SYMBOL indicates there is a  
potential hazard to personal safety involved and extra  
safety precaution must be taken. When you see this  
symbol, be alert and carefully read the message that  
follows it. In addition to design and configuration of  
equipment, hazard control and accident prevention  
are dependent upon the awareness, concern,  
prudence and proper training of personnel involved in  
the operation, transport, maintenance and storage of  
equipment.  
Do not allow anyone to operate  
this equipment who has not fully  
read and comprehended this  
manual and who has not been  
properly trained in the safe  
operation of the equipment.  
!
Operator should be familiar with  
!
Be Aware of  
Signal Words  
WARNING  
all functions of the unit.  
Indicates a potentially hazardous  
situation which, if not avoided, could  
result in death or serious injury, and  
includes hazards that are exposed  
when guards are removed. It may also  
be used to alert against unsafe  
practices.  
Operate implement from the  
driver’s seat only.  
A Signal word designates a degree or  
level of hazard seriousness. The  
signal words are:  
Do not leave tractor or implement  
unattended with engine running.  
Dismounting from a moving  
tractor could cause serious injury  
or death.  
!
DANGER  
Indicates an imminently hazardous  
situation which, if not avoided, will  
result in death or serious injury. This  
signal word is limited to the most  
extreme situations, typically for  
machine components that, for  
functional purposes, cannot be  
guarded.  
!
CAUTION  
Do not stand between the tractor  
and implement during hitching.  
Indicates a potentially hazardous  
situation which, if not avoided, may  
result in minor or moderate injury. It  
may also be used to alert against  
unsafe practices.  
Keep hands, feet, and clothing  
away from power-driven parts.  
Wear snug fitting clothing to avoid  
entanglement with moving parts.  
Watch out for wires, trees, etc.,  
when raising implement. Make  
sure all persons are clear of  
working area.  
Turning tractor too tight may  
cause implement to ride up on  
wheels. This could result in injury  
or equipment damage.  
For Your Protection  
Thoroughly read and understand  
the “Safety Label” section, read all  
instructions noted on them.  
Shutdown and Storage  
Lower machine to ground, put  
tractor in park, turn off engine, and  
remove the key.  
Detach and store implements in a  
area where children normally do  
not play. Secure implement by  
using blocks and supports.  
OFF  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
1
     
Land Pride  
Important Safety Information  
These are common practices that may or may not be applicable to the products described in  
this manual.  
Reduce speed if towed load is not  
Use Safety  
Lights and Devices  
Transport  
Machinery Safely  
equipped with brakes.  
Use the following maximum  
speed - tow load weight ratios as  
a guideline:  
Slow moving tractors, self-  
propelled equipment, and towed  
implements can create a hazard  
when driven on public roads. They  
are difficult to see, especially at  
night.  
Flashing warning lights and turn  
signals are recommended  
whenever driving on public roads.  
Use lights and devices provided  
with implement.  
Comply with state and local laws.  
Maximum transport speed for  
implement is 20 mph. DO NOT  
EXCEED. Never travel at a speed  
which does not allow adequate  
control of steering and stopping.  
Some rough terrain require a  
slower speed.  
20 mph when weight is less  
than or equal to the weight of  
tractor.  
10 mph when weight is double  
the weight of tractor.  
IMPORTANT: Do not tow a load that  
is more than double the weight of  
tractor.  
Sudden braking can cause a  
towed load to swerve and upset.  
Allow implement to cool  
Keep Riders  
Off Machinery  
Riders obstruct the operator’s  
view they could be struck by  
foreign objects or thrown from the  
machine.  
Practice Safe Maintenance  
completely.  
Understand procedure before  
doing work. Use proper tools and  
equipment, refer to Operator’s  
Manual for additional information.  
Do not grease or oil implement  
while it is in operation.  
Inspect all parts. Make sure parts  
are in good condition & installed  
properly.  
Work in a clean dry area.  
Lower the implement to the  
ground, put tractor in park, turn off  
engine, and remove key before  
performing maintenance.  
Never allow children to operate  
Remove buildup of grease, oil or  
equipment.  
debris.  
Remove all tools and unused  
parts from implement before  
operation.  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
2
Land Pride  
Important Safety Information  
These are common practices that may or may not be applicable to the products described in  
this manual.  
Avoid High  
Pressure Fluids Hazard  
Escaping fluid under pressure can  
penetrate the skin causing serious  
injury.  
Avoid the hazard by relieving  
pressure before disconnecting  
hydraulic lines.  
Wear  
Prepare for Emergencies  
Be prepared if a fire starts.  
Protective Equipment  
Protective clothing and equipment  
Keep a first aid kit and fire  
should be worn.  
extinguisher handy.  
Wear clothing and equipment  
appropriate for the job. Avoid  
loose fitting clothing.  
Prolonged exposure to loud noise  
can cause hearing impairment or  
hearing loss. Wear suitable  
hearing protection such as  
earmuffs or earplugs.  
Operating equipment safely  
requires the full attention of the  
operator. Avoid wearing radio  
headphones while operating  
machinery.  
Keep emergency numbers for  
doctor, ambulance, hospital and  
fire department near phone.  
Use a piece of paper or  
cardboard, NOT BODY PARTS, to  
check for suspected leaks.  
Wear protective gloves and safety  
glasses or goggles when working  
with hydraulic systems.  
If an accident occurs, see a  
doctor immediately. Any fluid  
injected into the skin must be  
treated within a few hours or  
gangrene may result.  
911  
Tire Safety  
Handle  
Chemicals Properly  
Tire changing can be dangerous  
and should be preformed by  
trained personnel using the  
correct tools and equipment.  
When inflating tires, use a clip-on  
chuck and extension hose long  
enough to allow you to stand to  
one side and NOT in front of or  
over the tire assembly. Use a  
safety cage if available.  
Protective clothing should be  
worn.  
Handle all chemicals with care.  
Follow instructions on container  
label.  
Agricultural chemicals can be  
dangerous. Improper use can  
seriously injure persons, animals,  
plants, soil, and property.  
Inhaling smoke from any type of  
chemical fire is a serious health  
hazard.  
When removing and installing  
wheels, use wheel handling  
equipment adequate for the  
weight involved.  
Store or dispose of unused  
chemicals as specified by the  
chemical manufacturer.  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
3
Land Pride  
Important Safety Information  
specified by Land Pride. When ordering new components  
make sure the correct safety labels are included in the  
request.  
Safety Labels  
Your Grooming Mower comes equipped with all safety  
labels in place. They were designed to help you safely  
operate your implement. Read and follow their  
directions.  
4. Refer to this section for proper label placement.  
To install new labels:  
a. Clean the area the label is to be placed.  
1. Keep all safety labels clean and legible.  
b. Spray soapy water on the surface where the label is to  
be placed.  
2. Replace all damaged or missing labels. To order new  
labels go to your nearest Land Pride dealer or visit our  
dealer locator at landpride.com.  
3. Some new equipment installed during repair requires  
safety labels to be affixed to the replaced component as  
c. Peel backing from label. Press firmly onto the surface.  
d. Squeeze out air bubbles with the edge of a credit card.  
818-130C  
Caution  
13304  
818-229C  
Amber Reflector  
15947  
818-230C  
Red Reflector  
15946  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
12/10/07  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Land Pride  
Important Safety Information  
818-237C  
Caution: V-Belt  
15945  
818-142C  
Danger:  
15944  
Rotating Driveline  
818-555C  
Danger: Rotating Blade  
15945  
818-556C  
Danger: Thrown Object  
15945  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
5
Land Pride  
Important Safety Information  
818-558C  
Warning:  
15943  
General Safety  
818-552C  
ROTATING DRIVELINE  
KEEP AWAY!  
Danger:  
Rotating Driveline  
13314  
818-540C  
Danger: Guard Missing  
13314  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
6
Land Pride  
Introduction  
LInantdrPoridde uweclcotmioesnyou to the growing family of new  
Owner Assistance  
product owners.  
The Warranty Registration card should be filled out by  
the dealer at the time of purchase. This information is  
necessary to provide you with quality customer service.  
This Grooming Mower has been designed with care and  
built by skilled workers using quality materials. Proper  
assembly, maintenance and safe operating practices will  
help you get years of satisfactory use from the machine.  
If customer service or repair parts are required contact a  
Land Pride dealer. A dealer has trained personnel, repair  
parts and equipment needed to service the Grooming  
Mower.  
Application  
The Land Pride FDR3590 Rear Discharge Grooming  
Mowers are designed and built to provide high  
productivity and excellent cutting quality on well-  
maintained lawn and turf surfaces. These mowers are  
adapted for category 1 attachment and operation on 25-  
60hp utility tractors. The 90" rear discharge cutting decks  
and highly durable construction make them well suited to  
meet the mowing needs of large estate owners, golf  
course, theme parks, municipalities, ranchers, horse  
breeders, and commercial mowing and landscape  
operations. The rear discharge cutting deck will provide a  
superb quality of cut and superior clipping distribution  
when grass is cut on a frequent basis and ground  
conditions are not wet.  
The parts on your Grooming Mower have been specially  
designed and should only be replaced with genuine Land  
Pride parts. Therefore, should your Grooming Mower  
require replacement parts go to your Land Pride Dealer.  
Serial Number Plate  
For prompt service always use the serial number and  
model number when ordering parts from your Land Pride  
dealer. Be sure to include your serial and model numbers  
in correspondence also. Refer to Figure 1 for the location  
of your serial number plate.  
for additional information and performance enhancing  
options.  
Using This Manual  
This Operator’s Manual is designed to help familiarize  
you with safety, assembly, operation, adjustments,  
troubleshooting, and maintenance. Read this manual  
and follow the recommendations to help ensure safe  
and efficient operation.  
15942  
Serial Number Plate Location  
Figure 1  
The information contained within this manual was  
current at the time of printing. Some parts may change  
slightly to assure you of the best performance.  
Further Assistance  
Your dealer wants you to be satisfied with your new  
Grooming Mower. If for any reason you do not  
understand any part of this manual or are not satisfied  
with the service received, the following actions are  
suggested:  
To order a new Operator’s or Parts Manual contact  
your authorized dealer. Manuals can also be  
downloaded, free-of-charge from our website at  
Service & Support Center by your dealer.  
1. Discuss the matter with your dealership service  
manager making sure he is aware of any problems  
you may have and that he has had the opportunity to  
assist you.  
Terminology  
“Right” or “Left” as used in this manual is determined by  
facing the direction the machine will operate while in use  
unless otherwise stated.  
2. If you are still not satisfied, seek out the owner or  
general manager of the dealership, explain the  
problem and request assistance.  
Definitions  
NOTE: A special point of information that the  
operator must be aware of before continuing.  
3. For further assistance write to:  
Land Pride Service Department  
1525 East North Street  
P.O. Box 5060  
IMPORTANT: A special point of information related  
to its preceding topic. Land Pride’s intention is that  
this information should be read and noted before  
continuing.  
Salina, Ks. 67402-5060  
E-mail address  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
12/10/07  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Land Pride  
Section 1: Assembly and Set-up  
Section 1: Assembly and Set-up  
4. Remove 5/8"-18 x 5" GR5 long bolt (#8), lock washer  
(#10), and hex nut (#11) from the upper pivoting hitch  
subassembly.  
Tractor Requirements  
This mower is designed with a 3-Point category I hitch.  
Horse power rating of tractor should not exceed 60 horse  
power. Tractor’s rear power take-off (PTO) speed and  
spline type must be capable of 540 RPM and 1 3/8”-6  
spline rear power take-off.  
5. Swing upper hitch bars (#1) up to a vertical position.  
Raise upper hitch braces (#2) up inside the upper  
hitch bars as shown.  
6. Assemble upper pivoting hitch (#3), spacer top hitch  
(#9), 5/8" x 5" long bolt (#8), lock washer (#10), and  
hex nut (#11) as shown.  
NOTE: In order to maintain steering control, ballast  
may need to be added to your tractor. To determine  
whether or not to add the ballast, refer to your  
tractors’ operator manual.  
7. Tighten all installed 5/8” nuts to proper torque. See  
Upper Hitch Arms  
Refer to Figure 1-1:  
Gauge Wheels  
Refer to Figure 1-1:  
1. Remove upper hitch bars (#1), upper hitch braces  
(#2), and upper pivoting hitch subassembly (#3) from  
storage position on top of mower deck.  
1. Remove 1/2”-13 x 1 1/4” GR5 bolts (#16) securing  
gauge wheel arms (#12) and turn gauge wheel arms  
180 degrees as shown. Replace bolts and retighten  
to proper torque per Torque Values Chart on page  
2. Bolt upper hitch braces (#2) to the mounting tabs  
located on the back of the deck using 5/8"-18 x 1 1/2”  
GR5 bolts (#4), lock washer (#5), and hex nut (#6).  
2. Mount gauge wheels (#13) to gauge wheel arms  
(#12), placing the 1/4”, 1/2” and 1” spacers (#14) at  
the desired depth. Secure gauge wheels with the  
linchpins (#15).  
3. Mount upper hitch bars (#1), to the inside of the front  
hitch plates on the frame using 5/8"-18 x 1 3/4" GR5  
bolts (#7), lock washers (#5) and hex nuts (#6).  
Upper Hitch Arms Assembly  
Figure 1-1  
15941  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
12/10/07  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Land Pride  
Section 1: Assembly and Set-up  
Tractor Hook-Up  
IMPORTANT: Some tractors are equipped with  
multi-speed PTO ranges. Be certain your tractor ‘s  
PTO is set for 540 rpm.  
Refer to Figure 1-2:  
1. Be certain tractor draw bar will not interfere. Move  
draw bar ahead or remove if required. Draw bar  
should also be checked for clearance when unit is  
being raised for the first time.  
IMPORTANT: Avoid premature driveline  
breakdown. A driveline that is operating must not  
exceed an angle of 25 degrees up or down while  
operating the 3-point lift. See Figure 1-3 below.  
2. Align lower link arms of tractor to the hitch clevises  
on the mower. Insert lower hitch pins into lower ball  
swivels and attach linchpins.  
15948  
Upper Floating Hitch  
Lower Hitch Clevis  
Gauge Wheel  
13800  
Maximum PTO driveline Movement During Operation  
Figure 1-3  
Tractor Hook-Up  
Figure 1-2  
IMPORTANT: Always check driveline maximum and  
minimum length during initial setup, when connecting  
to a different tractor and when alternating between  
using a quick hitch and a standard 3-point hitch. More  
than one driveline may be required to fit all  
applications.  
3. Attach tractor top link to upper floating hitch on  
mower with pin supplied. Secure with hairpin cotter.  
4. To allow mower flotation, adjust tractor top link in or  
out to place upper hitch pin vertically above the lower  
hitch pins as shown in Figure 1-2.  
Checking Driveline Minimum Length  
PTO Hookup  
IMPORTANT: Aligning tractor’s PTO shaft level with  
the Grooming Mower’s PTO shaft is necessary when  
checking to see if the driveline will fit correctly  
between tractor and Grooming Mower.  
If the Grooming Mower is to be used on more than one  
tractor, an additional driveline may be required.  
!
WARNING  
Refer to Figure 1-4 on page 10  
Do not operate a damaged driveline. Damaged drivelines can  
cause serious injury or death.  
1. Start tractor and slowly engage tractor’s hydraulic  
3-point to lift the lower arms until the Grooming  
Mower’s driveline shaft is approximately level with  
tractor's PTO shaft.  
!
CAUTION  
2. Slide inner driveline universal joint over the splined  
input shaft of the gearbox. Secure with driveline yoke  
locking device.  
Tractor PTO shield and all Grooming Mower guards must be  
in place at all times during operation!  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
12/10/07  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Land Pride  
Section 1: Assembly and Set-up  
3. Slide tractor outer driveline universal joint over the  
tractor’s splined driveline shaft. Secure with driveline  
yoke locking device. Skip to step 5 if driveline fits  
between tractor and implement.  
not less than 1/3 the free length with both inner and outer  
profile tubes being of equal length.  
1. Apply multi-purpose grease to the inside of the outer  
shaft and reassemble the driveline.  
2. Assemble the two driveline profiles together with just  
1/3 overlapping of the profile tubes as shown in  
Figure 1-5. Measure and record this overall length for  
checking driveline length in step 9 below.  
3. Attach inner driveline yoke end to the Grooming  
Mower gearbox input shaft.  
24513  
22009  
Driveline Shortening  
Figure 1-4  
4. The driveline will require shortening if it is too long.  
Shorten driveline as follows:  
a. Raise 3-point lower arms until Grooming Mower  
and tractor PTO shafts are approximately level  
with each other. Securely block Grooming Mower  
frame in this position. Set tractor in park, shut  
tractor engine off, set park brake and remove  
switch key.  
Outer Shielding has been removed for clarity.  
Driveline Maximum Length  
Figure 1-5  
4. Attach outer driveline yoke end to the tractor's PTO  
shaft.  
b. Pull driveline apart into two sections as shown in  
Figure 1-4. Attach outer driveline universal joint to  
the tractor PTO shaft and inner driveline universal  
joint to the Grooming Mower gearbox shaft. Pull  
on each driveline section to be sure the universal  
joints are secured to the shafts.  
5. The driveline should now be moved back and forth to  
insure that both ends are secured to the tractor and  
Grooming Mower PTO shafts. Reattach any end that  
is loose.  
c. Hold driveline sections parallel to each other to  
determine if they are too long. The inner and outer  
shields on each section should end approximately  
1" short of reaching the universal joint shield on  
the adjacent section (see “B” dimension). If they  
are too long, measure 1" (“B” dimension) back  
from the universal joint shield and make a mark at  
this location on the inner and outer driveline  
shields.  
IMPORTANT: A small chain is supplied with the  
driveline. This chain must be attached to the inner  
driveline shield and to the Grooming Mower to  
restrict shield rotation.  
6. Hook driveline safety chain in the hole in the inner  
driveline guard. Attach the other end to the  
Grooming Mower’s main frame.  
7. Start tractor and raise Grooming Mower just enough  
to remove blocks.  
d. Cut off the inner shield at the mark (“X”  
dimension). Cut the same amount off the inner  
shaft (“X1” dimension). Repeat cut off procedure  
(“Y” & “Y1” dimensions) to the outer driveline half.  
8. Slowly engage the tractor’s hydraulic 3-point to lower  
the Grooming Mower. Check for sufficient drawbar  
clearance. Move drawbar ahead, aside or remove if  
required.  
e. Remove all burrs and cuttings.  
Checking Driveline Maximum Length  
9. Raise and lower implement to find maximum  
extended driveline length. Check to make certain  
that the driveline overall length does not extend  
beyond the maximum recorded length in step 2  
above.  
Refer to Figure 1-5  
The driveline maximum length must, when fully  
extended, have a minimum overlap of the profile tubes by  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
12/10/07  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Land Pride  
Section 1: Assembly and Set-up  
Accessory Equipment  
Cutting Blades  
There are four blade choices to select from based upon  
soil condition, density of grass, and tractor horsepower.  
The appearance of the finish cut may vary between low  
lift and high lift blades. See your Land Pride dealer for  
blade availability.  
Anti-Scalping Front Roller  
Refer to Figure 1-6:  
1. Insert 4 x 10 roller wheel (#5) and spacer tubes (#4)  
between mounting bracket flanges as shown.  
2. Install front roller shaft (#2) through the bracket  
flanges, spacers and roller.  
Low Lift Blades  
Land Pride’s low lift blades are designed for mowing over  
sandy soil terrain where high suction lift is not crucial.  
Sand sucked into the blades accelerates blade wear  
more than normal. Low lift blades are recommended  
because they produce a lower suction keeping sand  
uplift and blade wear to a minimum.  
3. Secure roller shaft with 3/8”-16 x 1” GR5 hex head  
cap screw (#1) and lock nut (#3). Tighten lock nut to  
proper torque. See Torque Values Chart on page 25.  
Medium Lift Blades  
Land Pride’s medium lift blades are great when  
horsepower is a concern. They produce a medium  
suction for lifting grass requiring less horsepower than  
high lift blades. Medium Lift Blades are factory furnished  
with your mower.  
High Lift Blades  
Land Pride’s high lift blades develop the greatest suction  
for lifting grass before cutting for that fresh clean cut look.  
However, they may require more horsepower especially  
when cutting tall dense grass. They are not  
recommended for sandy soil conditions.  
Mulching Blades  
Land Pride’s mulching blades are designed to chop  
leaves and/or grass into smaller parts leaving your lawn  
looking fresher and cleaner than ever before.  
16570  
Front Roller Assembly  
Figure 1-6  
Accessory Part Numbers  
Land Pride All-Flex Mower Accessories  
Part No.  
Part Description  
Front Roller  
310-233A  
FDR3590 Front Roller  
Low Lift Blades (3 blades needed)  
890-205A  
Mower Blade 5/16 x 31 17/32 SD LL CW  
Medium Lift Blades (3 blades needed)  
890-533C  
Mower Blade 5/16 x 31 17/32 SD ML CW  
High Lift Blades (3 blades needed)  
890-223C  
Mower Blade 5/16 x 31 17/32 SD HL CW  
Mulching Blades (3 blades needed)  
890-704C  
Mower Blade 1/46 x 31 17/32 SD CW  
See your Land Pride dealer for blade availability.  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
12/10/07  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Section 2: Operating Instructions  
Section 2: Operating Instructions  
3. Carefully raise and lower the implement to ensure  
Tractor Shut Down Procedure  
that the drawbar, tires, and other equipment on the  
tractor do not contact the frame or PTO driveline.  
It is essential that the tractor be shut down as noted  
below before making any inspections, maintenance and/  
or repairs to the tractor and/or mower.  
4. With the PTO disengaged and completely stopped,  
check the mower blades for sharpness. See “Service  
1. Park tractor on a level surface. Don’t work under or  
around an implement parked on a steep incline.  
IMPORTANT: Do not exceed rated PTO speed of  
mower. Excessive engine speed will cause damage  
to the power train components.  
2. Place tractor in park and set park brake.  
3. Disengage PTO if operating.  
4. Shut engine off and remove switch key.  
5. Wait for PTO to come to a complete stop before  
dismounting tractor.  
IMPORTANT: Stop PTO rotation immediately if  
vibration occurs during operation. Wait for mower to  
come to a complete stop. Follow all tractor shut  
down procedures before dismounting from the  
tractor to check for probable causes.  
6. Wear safety glasses.  
Operation Check  
It is absolutely essential that no one operates the  
Grooming Mower without first having read, fully  
understood and become totally familiar with the  
Operator’s Manual. Make sure the operator has paid  
particular attention to:  
5. Set tractor throttle to idle or slightly above idle and  
slowly engage the PTO. Once the Grooming Mower  
is running smoothly, increase tractor PTO speed to  
540 rpm PTO speed. Stop PTO rotation immediately  
if vibration occurs at any time. Wait for the PTO to  
come to a complete stop and then dismount from the  
tractor to check for probable causes.  
Transporting  
!
CAUTION  
Make the following inspections after attaching the  
Grooming Mower to the tractor. See hook-up instructions  
beginning on page 9. Make certain PTO is disengaged  
and completely stopped before continuing.  
When traveling on public roads, whether at night or during the  
day, use accessory lights and devices for adequate warning to  
operators of other vehicles. Comply with all Federal, State,  
and local laws.  
1. Inspect tractor safety equipment to make sure it is in  
good working condition.  
NOTE: Always disengage PTO before raising the  
mower to transport position.  
2. Complete the Operating Checklist below:  
1. When raising mower to transport position, be sure  
driveline does not contact tractor or mower. Adjust  
and set tractor’s 3-point hitch lift height so that the  
PTO shaft does not contact mower deck in the fully  
raised position.  
Operating Checklist  
Check  
Reference  
Check oil level in gearboxes.  
Section 5  
2. Be sure to reduce tractor ground speed when  
turning; and leave enough clearance so the mower  
does not contact obstacles such as buildings, trees  
or fences.  
Check that all plugs in gearbox  
have been replaced properly.  
Section 5  
Check initially and periodically for  
loose bolts and pins. Be sure all  
nuts and bolts are tight. Especially  
make sure mower blades, bolts and  
nuts are tight.  
Section 8  
3. Select a safe ground travel speed when transporting  
from one area to another. When traveling on  
roadways, transport in such a way that faster moving  
vehicles may pass you safely. A slow moving vehicle  
sign should always be properly displayed when  
traveling on public roads or right-of ways.  
Be certain all guards and shields  
are in place and in good condition.  
Section 1  
4. Shift tractor to a lower gear when traveling over  
rough or hilly terrain.  
Lubricate the mower as needed.  
Refer to “Maintenance and  
Lubrication”.  
Section 5  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
12  
       
Land Pride  
Section 2: Operating Instructions  
6. Do not make sharp turns or attempt to back up while  
Mowing Instructions  
mower is on the ground.  
7. Do not engage PTO with mower in the fully raised  
position. Do not engage or disengage PTO at full  
throttle.  
!
DANGER  
Gearbox shields must be secured in place when operating to  
avoid injury or death from entanglement in rotating drivelines.  
8. Grass is best cut when it is dry. Mowing wet grass  
can cause plugging resulting in grass clumps behind  
the mower.  
!
CAUTION  
9. Mower blades will cut better at a faster blade speed  
than at reduced throttle.  
Do not over speed PTO or machine damage may result. Know  
what your tractor requirements are.  
10. Grass should be mowed frequently as shorter  
clippings deteriorate faster.  
!
11. If mowing extremely tall grass, it is best to raise  
cutting height and mow the area, then lower cutting  
height and mow a second time at the desired height.  
DANGER  
Do not use deck as a fan. Cutting blades are not properly  
designed or guarded for this use. Using the deck as a fan can  
result in injury and/or death.  
12. Periodically check for foreign objects wrapped  
around the Grooming Mower blades. Remove  
foreign objects only after following “Tractor Shut  
!
DANGER  
Do not operate and/or travel across steep inclines where a  
tractor can roll-over resulting in serious injury or death.  
Consult your tractor’s manual for acceptable inclines the  
tractor is capable of traveling across.  
Un-hooking the Mower  
The following steps should be done when un-hooking the  
Grooming Mower from the tractor.  
1. Park on a level solid surface.  
2. Shut tractor engine off and engage parking brake.  
!
CAUTION  
When mowing in sandy soil areas, wear may occur to your  
mower blades caused from sand erosion. Frequent inspection  
should be made and blades replaced if damaged. Low lift  
blades are available from your Land Pride dealer.  
3. Lower deck to level ground or onto blocks supporting  
the deck just above ground level.  
4. Follow all tractor shut down procedures outlined on  
page 12 before dismounting from the tractor.  
1. Clear the area to be mowed of rocks, branches and  
other foreign objects that might be picked up and  
thrown by the mower blades.  
5. Unhitch Grooming Mower from tractor.  
6. See “Storage” on page 19 if mower is not going to  
IMPORTANT: Do not exceed rated PTO speed of  
mower. Excessive engine speed will cause damage  
to the power train components.  
IMPORTANT: Stop PTO rotation immediately if  
vibration occurs during operation. Wait for mower to  
come to a complete stop. Follow all tractor shut  
down procedures before dismounting from the  
tractor to check for probable causes.  
2. Lower mower to ground. Set tractor throttle at idle.  
Engage PTO to start blades rotating.  
3. Operate with 540 rpm PTO tractor. Mower blades will  
cut better at a 540 RPM than at reduced throttle.  
4. At first, begin mowing in a low gear and shift up until  
the desired speed is achieved - maintain 540 PTO  
rpm regardless of gear selection.  
5. After mowing the first 50 feet, stop and check to see  
that the mower is adjusted properly.  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
12/10/07  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Land Pride  
Section 2: Operating Instructions  
The proper mowing speed will ultimately be determined  
by ground conditions, desired finish, common sense, and  
good safe mowing practices by the operator. Grass is  
best cut when it is dry. Mowing in wet grass can cause  
plugging resulting in grass clumps behind the mower.  
Grass should be mowed frequently as shorter clippings  
deteriorate faster. When mowing in tall grass it is best to  
raise the cutting height, mow the area, then lower the  
cutting height, and mow a second time.  
General Operating Instructions  
By now you should have thoroughly read your FDR  
Grooming Mower Operator’s Manual, properly attached  
your Land Pride FDR3590 to your tractor, and reviewed  
the operating checklist. You should have also inspected  
the area where you intend to mow and cleared it of safety  
hazards and foreign objects. If you have not yet  
completed all of these functions, it is an absolute must  
that you do so now before proceeding.  
After mowing approximately 50 ft., stop the tractor,  
disengage the PTO, set the brake, turn off the engine,  
remove the key, and dismount the tractor to see if the  
mower is adjusted properly. If you need to dismount the  
tractor on a hill or incline to inspect, adjust, or park the  
mower for any reason, place wheel chocks under the  
rear tires for added safety. Once you have made  
necessary adjustments, you may continue mowing. Do  
not engage the PTO at high engine rpm and avoid  
making sharp turns if at all possible. If some one  
approaches while you are mowing, disengage the PTO  
and stop the tractor.  
Now that you are properly briefed and prepared its time  
to start the tractor and move to your starting point. When  
transporting to your mowing site, select a safe ground  
transport speed. When traveling on roadways, transport  
in such a manner that faster moving vehicles can easily  
see you and pass you safely. When travelling over rough  
and hilly terrain, reduce your speed, avoid quick or sharp  
steering corrections. Take extra care to insure that the  
mower doesn’t come into contact with obstacles such as  
trees, buildings or fences.  
When you have arrived at the mowing site, start the  
tractor, raise the deck to make sure that everything is  
properly attached and that the driveline is not in a bind or  
in contact with the mounting frame. Also make sure the  
tractor tires aren’t in contact with the deck. With the deck  
still in the raised position, proceed to your starting point  
and lower your deck to the ground in mowing position.  
Reduce your tractor engine rpm to idle and engage the  
PTO. Gradually raise the tractor engine rpm to achieve  
the 540-rpm PTO speed. Now begin mowing at a ground  
speed of approximately 4-5mph.  
With a little practice and experience you will become very  
good at operating your Land Pride FDR3590 Rear  
Discharge Grooming Mower. Always remember that  
there is no substitute for proper maintenance and good  
safe operating practices.  
options.  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
12/10/07  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Land Pride  
Section 3: Adjustments  
Section 3: Adjustments  
Leveling the Mower  
Cutting Height Adjustment  
NOTE: Tractor and mower should be on level  
ground.  
Refer to Figure 3-1:  
1. Using the tractor, raise the mower off the ground and  
support under it with secure blocking so not to let the  
mower drift down during maintenance.  
1. Set lower hitches and upper floating hitch, as shown  
below in Figure 3-1.  
2. Holding wheel and yoke assembly up, remove  
quick-lock pin from top of gauge wheel spindle.  
2. Start tractor and raise mower, watching that tractor  
draw bar (if not removed) does not interfere with  
mower.  
3. Position 1” spacers, 1/2” spacer and 1/4” spacers as  
required. All spacers on top of spindle tube allows for  
approximately 3/4" cutting height. Adjustments  
range from 3/4" to a maximum of 3-1/4" in 1/4"  
increments.  
3. Slowly lower mower until gauge wheels touch the  
ground and the lower mower 3-point hitch bars are  
parallel to the ground in floating position. Set tractor  
3-point stop.  
4. Set park brake and turn off tractor. Remove key from  
ignition.  
Refer to “Leveling the Mower” beginning on this  
page.  
5. Rotate blades parallel to direction of travel as shown  
in Figure 3-2 below.  
For a guide on measuring cutting height refer to  
Cutting Height Chart below.  
6. Measure clearance from the cutting edge to the  
ground at front and rear of the blade. This  
measurement should be equal or have the blade at  
the front of the mower not more than 1/2" lower than  
the blade at the rear of the mower.  
Cutting Height Chart  
A
B
5 5/8"  
6 1/8"  
7 1/8"  
8 1/8"  
9 1/8"  
10 1/8"  
3/4"  
15948  
Upper Floating Hitch  
1 1/4"  
2 1/4"  
3 1/4"  
4 1/4"  
5 1/4"  
Spindle Tube  
Linchpin  
Gauge Wheel Spacers  
Lower Hitches  
Gauge Wheel  
3-Point Hitch  
Figure 3-1  
12742  
Cutting Height  
Figure 3-2  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
15  
       
Land Pride  
Section 3: Adjustments  
3. Excessive tension on the belt may lead to premature  
failure of belt and drive components. Excessive  
tension on the belt may also lead to a safety hazard  
to the operator or bystanders. Not enough tension on  
the belt may lead to premature failure of the belt due  
to excessive slipping.  
3-Point Hitch Adjustments  
The 3-point hitch system on this mower has been  
designed for front to back flotation when mowing on  
uneven terrain. Adjust tractor’s top link to place the upper  
hitch pin vertically above the lower hitch pins as shown in  
Figure 3-1 on page 15.  
!
WARNING  
!
CAUTION  
Excessive tension on the belt may shorten the useful life of belt  
and drive components. Excessive tension on the belt may also  
lead to a safety hazard to the operator or bystanders.  
Engage parking brake, shut off tractor, remove key and  
disengage PTO before making any height adjustments!  
Belt Tension  
Refer to Figure 3-3:  
!
CAUTION  
Belt drive system under spring tension; use care to avoid  
bodily harm!  
1. To check tension, apply force at arrow A. With a  
tension tester and deflect belt 1/4". The force  
required to get this deflection should range from 7 to  
10 lbs.  
2. To adjust belt tension, adjust eyebolt (#1), as  
necessary. This adjustment will increase or decrease  
tension on spring (#2).  
16642  
Belt Tension  
Figure 3-3  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
12/10/07  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Land Pride  
Section 4: Maintenance and Lubrication  
Section 4: Maintenance and Lubrication  
Service Mowing Blades  
Blade Inspection  
Maintenance  
Proper servicing and adjustment is the key to the long life  
of any implement. With careful and systematic  
inspection, you can avoid costly maintenance, time and  
repair.  
Refer to Figure 4-1:  
Blade Wear: As blades wear and are resharpened, the  
blade performance will be reduced.  
Bent, Deformed or Split Blades: Should be removed from  
unit and discarded. DO NOT attempt to straighten for  
reuse.  
!
CAUTION  
For safety reasons, each maintenance operation must be  
performed with the tractor’s PTO disengaged, the mower  
lowered completely to the ground or on safely supported  
blocking, tractor engine shut off and ignition key removed.  
!
WARNING  
DO NOT attempt to modify blade, such as hard surfacing, heat  
After using the mower for several hours, check all bolts  
to be sure they are tight and check the tension of the  
drive belt. Refer to Belt Tension in the “Adjustments”  
section on page 16.  
or cold treating and/or by any other method.  
!
WARNING  
Also check drive belt tension after several hours of  
mowing. Refer to Belt Tension in the “Adjustments”  
section on page 16.  
DO NOT try to straighten a blade that is bent. Never weld a  
broken or cracked blade. ALWAYS replace with a new Land  
Pride blade to assure safety.  
Lubricate items as listed under Lubrication, this section,  
starting on page 20.  
Blade Removal And Installation  
Replace any worn, damaged or illegible safety labels by  
obtaining new labels from your Land Pride Dealer.  
Information about labels is located under Safety Labels in  
the “Important Safety Information” section starting on  
!
CAUTION  
Depending on blade rotation, bolts attaching mower blades to  
their respective spindles may be either left hand or right hand.  
Prevent spindle and/or bolt damage by knowing which hand  
the threads are before removing and/or tightening any blade  
mounting bolts.  
19328  
Inspection of Blades & Sharpening  
Figure 4-1  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
17  
         
Land Pride  
Section 4: Maintenance and Lubrication  
Refer to Figure 4-2 & Figure 4-2:  
1. Verify blade rotation and bolt thread type (right hand  
or left hand) before loosening center blade bolts and  
removing blade to be sharpened or replaced. The  
FDR3590 is equipped with right hand threaded center  
blade bolts.  
IMPORTANT: Center Blade bolts have right hand  
threads.  
23789  
24524  
Blade & Blade Bar Removal  
Figure 4-3  
Blade Sharpening or Replacement  
Blades Rotation: CW / Center Blade Bolt: R.H Threads  
!
CAUTION  
ALWAYS wear eye protection and gloves when sharpening a  
blade.  
Blade Placement  
Figure 4-2  
Refer to Figure 4-3:  
IMPORTANT: Always install blade with the cutting  
edge facing direction of rotation.  
2. Remove blades by grasping the blade end with a rag  
or thick padded glove while loosening the blade  
mounting bolt.  
IMPORTANT: Replace blades with Land Pride blades  
only.  
3. Remove center blade bolt (#4) and two outside blade  
bar bolts from the bottom of the blade to be replaced.  
1. If the blade cutting edge is dull or nicked, it should be  
replaced or sharpened. Remove blades for replacing  
or sharpening by grasping end of the blade using a rag  
or a thick, padded glove, while loosening and  
IMPORTANT: Replace blades with Land Pride blades  
only.  
IMPORTANT: Always install blades with cutting edge  
facing direction of blade spindle rotation and with wing  
tips pointing up towards bottom of deck.  
removing the bolt/bolts that mount the blade.  
2. Clean blade, blade washer and mounting surface of  
all debris before replacing or sharpening. Grind  
cutting edge at the same bevel as the original. See  
Figure 4-4. Sharpen only the top of the cutting edge  
to maintain sharpness.  
IMPORTANT: See Figure 4-3. Loctite is not required  
if blade (#1) is removed without removing blade bar  
(#2). However, If blade bar (#2) is removed from  
spindle shaft (#3), then apply loctite 243 to spindle  
shaft threads and to center bolt threads (#4).  
19327  
4. Reinstall blade, blade washer and bolt. Care should  
be taken when installing the blade bolt to not get it  
cross threaded and to know if the bolt is right hand or  
left hand. Do not exceed 55 ft.-lbs. of torque on bolt.  
5. Reinstall the two outside bolts. Tighten to correct  
torque listed in the Torque Values Chart in the  
“Appendix” section on page 25.  
Blade Sharpening  
Figure 4-4  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
12/10/07  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Land Pride  
Section 4: Maintenance and Lubrication  
3. Check blade balance by positioning the blade  
horizontally on a nail or shaft through the center hole.  
See Figure 4-5. If either end of the blade rotates  
downward, grind (remove) metal on that end until  
blade will balance. The blade is properly balanced  
when neither end drops. Balance of a blade is  
generally maintained by removing an equal amount  
of material from each end of blade when sharpening.  
Storage  
At end of working season or when the mower will not be  
used for a long period, it is good practice to clean off any  
dirt or grease that may have accumulated on the mower  
and any of the moving parts.  
1. Clean off any dirt or grease that may have  
accumulated on the deck and moving parts. Scrape  
off compacted dirt from the bottom of the deck and  
then wash the surface thoroughly with a garden hose.  
A coating of oil may also be applied to the lower deck  
area to minimize oxidation.  
HORIZONTAL  
2. Check blades for wear and replace if necessary, see  
Servicing Mowing Blades, this section on page 17.  
3. Inspect mower for loose, damaged or worn parts and  
adjust or replace as needed.  
NAIL OR SHAFT  
19046  
Blade Balancing  
Figure 4-5  
4. Lubricate as noted in the Lubrication portion of this  
section starting on page 20.  
5. Store unit inside if possible for longer life.  
4. Mount blade with wing tips pointing up towards  
bottom of deck. Reinstall blade, blade washer and  
bolt. Care should be taken when installing blade bolt  
not to get it cross threaded. Do not exceed 55 ft.-lbs.  
of torque on bolt.  
6. Repaint parts where paint is worn or scratched to  
prevent rust. Ask your dealer for Aerosol Land Pride  
touch-up paint.  
Land Pride Touch-up Paint  
NOTE: Care should be taken in order not to remove  
any more material than necessary to sharpen blade.  
Part No.  
Part Description  
821-011C  
821-002C  
PAINT LP BEIGE SPRAY CAN  
PAINT GP BLACK SPRAY CAN  
Front of Mower  
V-Belt Installation  
Refer to Figure 4-6:  
This illustration is also on the label located on the top of  
the mower deck.  
1. Remove right hand and left hand belt covers.  
2. Disengage belt tension by loosening eyebolt (#1)  
and removing spring (#2) from the tension-chain  
link (#3).  
3. With tension relieved from belt remove old belt from  
pulleys.  
4. To install a new belt be sure belt is positioned in all  
the pulley grooves. Engage belt tension by  
assembling the tension spring back on the eyebolt  
and tightening eyebolt to apply tension to the new  
belt. Check belt tension, refer to Figure 3-3 on page  
16.  
23789  
V-Belt Installation  
Figure 4-6  
5. Reinstall all belt covers and secure in place with  
hardware.  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
19  
   
Land Pride  
Section 4: Maintenance and Lubrication  
Lubrication  
Lubrication  
Legend  
Multi-purpose  
spray lube  
Multi-purpose  
grease lube  
Multi-purpose  
oil lube  
Intervals in hours  
at which lubrication  
is required  
50  
25  
Hours  
Driveline Shaft U-Joints  
24871  
Type of Lubrication: Multi-purpose Grease  
Quantity - 4 to 8 Pumps  
20  
Hours  
Inner Tube Bearings  
Type of Lubrication: Multi-purpose Grease  
Quantity - As Required  
24871  
20  
Hours  
Driveline Profiles  
Type of Lubrication: Multi-purpose Grease  
Quantity - Clean & coat inner profile tube of driveline with  
a light film of grease and then reassemble.  
24873  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
20  
       
Land Pride  
Section 4: Maintenance and Lubrication  
As  
Required  
Gearbox  
IMPORTANT: Do not overfill! Level mower and wait  
for gearbox oil to cool before checking. mower that  
is not level or a gearbox with hot oil will not show  
correct oil level on the dipstick.  
Unscrew top vent plug in gearbox to remove dipstick. Wipe  
oil from dipstick and screw it back in without tightening.  
Unscrew dipstick and check oil level mark. If low, fill  
through top plug hole in gearbox with EP 80-90W oil until oil  
reaches full mark on the dipstick. Reinstall vent plug with  
dipstick and tighten.  
15951  
Take your gearbox to a Land Pride dealer if it requires  
service.  
Type of Lubrication: Gear Lube EP 80-90W  
Quantity = Fill until oil reaches full mark on dipstick.  
25  
Hours  
Wheel Support Bushings & Wheel Bearings  
Type of Lubrication: Multi-purpose Grease  
15949  
25  
Hours  
Bearing in Blade Spindle Hubs  
Type of Lubrication: Multi-purpose Grease  
15950  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
12/10/07  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
e  
Section 5: Specifications & Capacities  
Section 5: Specifications & Capacities  
FDR35 Series Rear Discharge Grooming Mowers  
FDR3590  
Max. Engine HP. 60 HP.  
Cutting Width 90"  
Overall Width 92”  
Height 40”  
Length 81”  
Weight (Semi-Solid Tires) 1026 lbs.  
Cutting Height 3/4” to 5 1/4” in 1/2” Increments  
Deck Material Thickness 3/16”  
Blades-3 5/16” x 2 1/2” x 31 1/2” Medium lift - Hardened  
Blade Overlap 2 1/4”  
Blade Tip Speed 18,500 F.P.M.  
Blade Spindles Cast Iron Greasable hubs: 1 3/8”  
Hitch Category l,  
Lower Hitch: Floating Clevis with Plated Pins  
Top Link: Floating Clevis  
Quick Hitch Fits Land Pride Quick-Hitch after S/N 294658  
Gauge Wheels Castered 5” x 13” Semi-Solid Tire with Bearings  
Caster Wheel Spindle 1 1/4” Diameter with Nylon Bushings  
Drive Train 540 RPM PTO  
Gearbox  
1:2.83 Ratio  
Cast Iron Housing  
Spring Loaded Single V-Belt  
Driveline Heavy-Duty W/Quick Coupler Cat. 2  
Optional Equipment Front Roller  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
22  
 
Land Pride  
Section 6: Features and Benefits  
Section 6: Features and Benefits  
FDR35 Series Rear Discharge Mowers  
Features  
Benefits  
Cutting width 90” Cutting width  
Gearbox HP rating 25 - 60 HP  
Rear discharge The wide, even dispersal of grass leaves a fine thin layer directly behind the mower vs. a  
possible windrow to the side. Keeps grass from blowing in unwanted areas. Easier to mow  
around objects.  
3/16” Deck thickness Heavy deck material to aid in overall strength and longevity. Reinforced spindle mounts.  
Clevis type lower hitch points Allows for easy hook-up by being able to remove pins and back into clevises.  
Floating 3-point Top and bottom hitch points float up and down which allows the mower to float over uneven  
terrain.  
Lower hitch points Accommodates many tractor configurations by adjusting in and out.  
adjust in and out  
13” Semi solid tires 13” Tires offer premium flotation. Roller bearings allow for a long life. Semi solid tires offer  
with roller bearings shock absorption.  
Heavy-duty Gauge wheel arms 1/4” Gauge wheel arms increases strength.  
Non-aligned gauge wheels Rear wheels do not track behind the front wheels to reduce laying grass over.  
High blade tip speed 18,500 fpm for cleaner cutting and better dispersion of clippings.  
Heavy-duty roller bearings Roller bearings for smooth running and quiet operation, 1 3/8" machined spindles for  
& 1 3/8" machined spindles durability, balanced performance, and accuracy. Cast iron housings for added protection and  
durability.  
Blade choices Low, medium or high lift blades are available to match the customer’s desires and needs for  
his particular uses. Mulching blades also available.  
Blade overlap Blade overlap of 2 1/4” assures no skipping in tight turns.  
Single C-section Kevlar belt Simple one belt design. Kevlar material adds additional strength.  
Spring loaded adjustable idler Allows for constant and proper pressure on the belt.  
Blade bar Bar gives additional support to blade.  
Top greasing spindles Assures top bearing gets greased. No shields to remove.  
5 Year Limited Gear Box Shows our confidence in the gearbox integrity. 5 year housing, gears, shafts,  
warranty 3 year bearings and seals.  
Quick Hitch Compatible Compatible with Land Pride Quick Hitch (S/N 294658+) for easy attachment and removal and  
increased productivity.  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
23  
 
e  
Section 7: Troubleshooting  
Section 7: Troubleshooting  
Problem  
Solution  
Check installation of belt.  
Discharge chute plugged  
Wait until grass dries.  
Raise cutting height of mower and cut grass twice.  
Mow at full throttle (540 PTO rpm), check PTO speed and tractor engine.  
Shift transmission to a lower gear.  
!
CAUTION  
Do not try to clean discharge chute when mower is running. Bodily harm may occur!  
Unplug and clean mower deck.  
Belt slipping  
Remove belt guard shields and clean sheaves.  
Tighten spring take-up eyebolt.  
Replace belt.  
Mow at full throttle (540 PTO rpm), check PTO speed and tractor engine.  
Shift transmission to a lower gear.  
Tighten spring take-up eyebolt.  
Patches of uncut grass  
Excessive vibration  
Sharpen and balance or replace blade.  
Remove belt guard shield and clean debris from belt area and sheaves. Replace  
the belt guard shield.  
Replace drive belt.  
Replace sheaves or align.  
Readjust 3-point hitch to raise mower to maximum of 14 inches.  
Check lubricant level.  
Gearbox noisy  
Raise cutting height by adjusting wheels.  
Change mowing pattern.  
Blades scalping grass  
Reduce speed turns.  
Shift to a lower gear.  
Uneven cut  
Level mower.  
Sharpen blades & balance or replace. Shimming of blade hubs may be required to  
level out all three blades. Blade hub shim part no. 310-367D (Optional).  
Mow at full throttle (540 PTO rpm).  
Shift to a lower gear.  
Tractor loaded down by mower  
Clean mower.  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
24  
 
Land Pride  
Section 8: Appendix  
Section 8: Appendix  
Torque Values Chart  
Bolt He a d Id e ntific a tion  
Bolt He a d Id e ntific a tion  
8.8  
10.9  
5.8  
Bolt Size  
(Me tric )  
Bolt Size  
(Inc he s)  
Class 5.8  
Class 8.8  
Class 10.9  
Grade 2  
Grade 5  
Grade 8  
1
3
in-tpi  
1/4" - 20  
1/4" - 28  
N · m ft-lb N · m ft-lb N · m ft-lb  
mm x pitch N · m ft-lb N · m ft-lb N · m ft-lb  
7.4  
8.5  
15  
5.6  
11  
8
16  
12  
M 5 X 0.8  
4
3
6
5
9
7
6
13  
10  
18  
14  
M 6 X 1  
7
5
11  
8
15  
11  
5/16" - 18  
5/16" - 24  
3/8" - 16  
3/8" - 24  
7/16" - 14  
7/16" - 20  
1/2" - 13  
1/2" - 20  
9/16" - 12  
9/16" - 18  
5/8" - 11  
5/8" - 18  
3/4" - 10  
3/4" - 16  
7/8" - 9  
11  
24  
17  
33  
25  
M 8 X 1.25 17  
12  
26  
19  
36  
27  
17  
13  
26  
19  
37  
27  
M 8 X 1  
18  
33  
13  
28  
21  
39  
29  
27  
20  
42  
31  
59  
44  
M10 X 1.5  
24  
52  
39  
72  
53  
31  
22  
47  
35  
67  
49  
M10 X 0.75 39  
M12 X 1.75 58  
29  
61  
45  
85  
62  
43  
32  
67  
49  
95  
70  
42  
91  
67  
125  
130  
145  
200  
l215  
315  
335  
405  
485  
610  
900  
93  
49  
36  
75  
55  
105  
145  
165  
210  
235  
285  
325  
510  
570  
820  
905  
78  
M12 X 1.5  
M12 X 1  
60  
44  
95  
70  
97  
66  
49  
105  
115  
150  
165  
205  
230  
360  
405  
585  
640  
875  
955  
76  
105  
120  
155  
170  
210  
240  
375  
420  
605  
670  
90  
66  
105  
145  
155  
225  
240  
310  
350  
440  
650  
760  
830  
77  
105  
150  
160  
230  
245  
300  
355  
450  
665  
75  
55  
85  
M14 X 2  
92  
68  
105  
115  
165  
180  
230  
260  
325  
480  
560  
610  
95  
70  
110  
120  
150  
170  
265  
295  
430  
475  
645  
705  
M14 X 1.5  
M16 X 2  
99  
73  
105  
130  
150  
235  
260  
225  
250  
340  
370  
480  
540  
680  
750  
890  
79  
145  
155  
195  
220  
280  
310  
480  
525  
960  
105  
115  
145  
165  
205  
230  
355  
390  
705  
97  
M16 X 1.5  
M18 X 2.5  
M18 X 1.5  
M20 X 2.5  
M20 X 1.5  
M24 X 3  
110  
170  
190  
165  
185  
250  
275  
355  
395  
500  
555  
655  
7/8" - 14  
1" - 8  
1050 780  
1150 845  
1230 910  
1350 995  
1750 1290  
1960 1440  
M24 X 2  
1" - 12  
M30 X 3.5  
M30 X 2  
1510 1120 2100 1550  
1680 1240 2320 1710  
1-1/8" - 7  
1 1/8" - 12  
1 1/4" - 7  
1 1/4" - 12  
1 3/8" - 6  
1 3/8" - 12  
1 1/2" - 6  
1 1/2" - 12  
1080 795  
1210 890  
1060 785  
M36 X 3.5  
1730 1270 2650 1950 3660 2700  
1880 1380 2960 2190 4100 3220  
1520 1120 2460 1820  
1680 1240 2730 2010  
1990 1470 3230 2380  
2270 1670 3680 2710  
2640 1950 4290 3160  
2970 2190 4820 3560  
M36 X 2  
1
in-tpi = nominal thread diameter in inches-threads per in.  
N· m = newton-meters  
2
3
4
1010 745  
1180 870  
1330 980  
ft-lb= foot pounds  
mm x pitch = nominal thread diameter in millimeters x thread  
pitch  
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
25  
   
Land Pride  
Section 8: Appendix  
Notes  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
26  
 
Land Pride  
Section 8: Appendix  
Warranty  
Land Pride warrants to the original purchaser that this Land Pride product will  
be free from defects in material and workmanship beginning on the date of  
purchase by the end user according to the following schedule when used as  
intended and under normal service and conditions for personal use.  
Overall Unit and Driveline: One year Parts and Labor  
Gearboxes:  
(S/N 329841+) 5 Years Parts and Labor  
(S/N 329840-) One year Parts and Labor.  
Belt, Blades, Friction Disc in Slip Clutches & Tires: Considered wear items.  
This Warranty is limited to the replacement of any defective part by Land Pride  
and the installation by the dealer of any such replacement part, and does not cover  
common wear items. Land Pride reserves the right to inspect any equipment or  
parts which are claimed to have been defective in material or workmanship.  
This Warranty does not apply to any part or product which in Land Pride’s  
judgment shall have been misused or damaged by accident or lack of normal  
maintenance or care, or which has been repaired or altered in a way which  
adversely affects its performance or reliability, or which has been used for a  
purpose for which the product is not designed. Misuse also specifically includes  
failure to properly maintain oil levels, grease points, and driveline shafts.  
Claims under this Warranty should be made to the dealer which originally sold  
the product and all warranty adjustments must be made through an authorized  
Land Pride dealer. Land Pride reserves the right to make changes in materials or  
design of the product at any time without notice.  
This Warranty shall not be interpreted to render Land Pride liable for damages  
of any kind, direct, consequential, or contingent to property. Furthermore, Land  
Pride shall not be liable for damages resulting from any cause beyond its  
reasonable control. This Warranty does not extend to loss of crops, any expense  
or loss for labor, supplies, rental machinery or for any other reason.  
No other warranty of any kind whatsoever, express or implied, is made  
with respect to this sale; and all implied warranties of merchantability and  
fitness for a particular purpose which exceed the obligations set forth in this  
written warranty are hereby disclaimed and excluded from this sale.  
This Warranty is not valid unless registered with Land Pride within 30 days from  
the date of purchase by the end user.  
FDR3590 Rear Discharge Grooming Mowers 310-229M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12/10/07  
27  
 
Corporate Office: P.O. Box 5060  
Salina, Kansas 67402-5060 USA  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Bolens Lawn Mower 117 030A User Manual
Briggs Stratton Lawn Mower 12E300 User Manual
Cub Cadet Lawn Mower 185 387 100 User Guide
Great Dane Lawn Mower GSRKA1952S User Guide
Hayter Mowers Lawn Mower 4113G User Guide
Scag Power Equipment Lawn Mower STT 35BVAC SS User Guide
Snapper Lawn Mower 1690624 User Guide
Snapper Lawn Mower CP215017KWV CP216017RV CP214017R2 User Manual
Stiga Lawn Mower COMFORT User Guide
Troy Bilt Lawn Mower 258 User Guide