PO Box 1200
305 Commerce Drive
Winfield, Alabama 35594
ROTARY MOWER
OPERATION AND PARTS
MANUAL
Part No 999998
Download from Www.Somanuals.com. All Manuals Search And Download.
TO THE PURCHASER
This manual contains valuable information about your
new King Kutter Mower. It has been carefully prepared to
give you helpful suggestions for operating, adjusting, ser-
vicing and ordering repair parts.
Keep this manual in a convenient place for quick and
easy reference. Study it carefully. You have purchased a de-
pendable and sturdy mower, but only by proper care and op-
eration can you expect to receive the service and long life
designed and built into it.
Sometime in the future your mower may need new parts
to replace those that are worn or broken. If so, go to your
dealer and provide him with the model and part number.
Customer Information
Name ______________________________________________
Purchased From ______________________________________
Date Purchased ______________________________________
Model No. ___________________________________________
Serial No. ___________________________________________
3
Download from Www.Somanuals.com. All Manuals Search And Download.
It is the purchaser and/or operator’s responsibility to….
Read and understand the information contained in this
manual.
Operate, lubricate, assemble and maintain the
equipment in accordance with all instructions and
safety procedures in this manual.
Inspect the equipment and replace or repair any
parts that are damaged or worn which under contin-
ued operation would cause damage, wear to other
parts, or cause a safety hazard.
Return the equipment or parts to the authorized
King Kutter dealer, from where it was purchased, for
service or replacement of defective parts that are
covered by warranty. (The King Kutter Factory may
inspect equipment or parts before warranty claims
are honored.)
Payment of all costs incurred by the dealer for traveling
to or transporting the equipment for warranty inspection
and or claims.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
ITEM
PAGE
Safety.........................................................................6
Assembly Instructions................................................8
Before Putting Into Service ...................................... 11
Safety Training.........................................................12
Operational Safety ...................................................14
Transportation Safety...............................................16
Attaching To Tractor .................................................17
Sizing PTO...............................................................19
Operating Instructions..............................................20
Maintenance ............................................................22
Maintenance Safety .................................................23
Safety Decal's And Locations...................................24
PTO Shaft Parts.......................................................29
Replacement Parts ..................................................32
PTO Shaft Cover Removal...................................…..37
Gearbox Parts..........................................................40
Warranty ………………………………………………...46
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ AND FOLLOW THE INSTRUC-
TIONS IN THIS MANUAL AND ESPE-
CIALLY IN THE SAFETY SECTION.
FAILURE TO DO SO CAN RESULT IN
SERIOUS INJURY OR DEATH.
TAKE NOTE! THIS SAFETY ALERT
SYMBOL FOUND THROUGHOUT
THIS MANUAL IS USED TO CALL
YOUR ATTENTION TO INSTRUC-
TIONS INVOLVING YOUR PERSONAL
SAFETY AND THE SAFETY OF OTH-
ERS.
THIS SYMBOL MEANS
ATTENTION!
BECOME ALERT!
YOUR SAFTEY IS INVOLVED
SIGNAL WORDS:
The signal words DANGER, WARNING and CAUTION are used with the safety
messages in this manual and with each safety signs. They are defined as fol-
lows:
DANGER: Indicates an immediate hazardous situation that, if not avoided,
could result in serious injury or death. This signal word is to be limited to the
most extreme situations typically for machine components that, for functional
purposes, cannot be guarded.
WARNING: Indicates a potentially hazardous situation that, if not avoided,
could result in serious injury or death, and includes hazards that are exposed
when guards are removed. It may also be used to alert against unsafe prac-
tices.
CAUTION: Indicates a potentially hazardous situation that, if not avoided, may
result in minor or moderate injury. It may also be used to alert against unsafe
practice.
If you have any questions not answered in this manual or require additional cop-
ies or the manual is damaged, please contact your dealer or King Kutter, Inc.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EQUIPMENT SAFETY GUIDELINES
Safety of the operator and by standards is one of the main concerns in designing and devel-
oping a mower. However, every year accidents occur which could have been avoided by a
few seconds of thought and a more careful approach to handling equipment. You, the op-
erator, can avoid many accidents by observing the following precautions and insist those
working with you, or for you, follow them.
In order to provide a better view, certain photographs or illustrations in this manual may
show an assembly with a safety shield removed. However, equipment should never be op-
erated in this condition. Keep all shields in place. If shield removal becomes necessary for
repairs, replace the shield prior to use.
Replace any safety sign that is not readable or is missing. Location of such safety signs is
indicated in this manual.
Never use alcoholic beverages or drugs that can hinder alertness or coordination while oper-
ating this equipment. Consult your doctor about operating this machine while taking pre-
scription medications.
Under no circumstances should children under the age of 18 be allowed to work with
this equipment. Do not allow persons to operate or assemble this unit until they have
read this manual and have developed a thorough understanding of the safety precau-
tions and of how it works. Review the safety instructions with all users annually.
This equipment is dangerous to children and persons unfamiliar with its operation. The op-
erator should be a responsible, properly trained and physically able person familiar with farm
machinery and trained in this equipment’s operations. If the elderly are assisting with farm
work, their physical limitations need to be recognized and accommodated.
Use a tractor equipped with a Roll Over Protective System and seat belts. (ROPS)
Never exceed the limits of a piece of machinery. If its ability to do a job, or to do so safely, is
in question- DON’T TRY IT.
Do not modify the equipment in any way. Unauthorized modification could result in serious
injury or death and may impair the function and life of the equipment.
In addition to the design and the confirmation of this implement, including safety signs and
safety equipment, hazard control and accident prevention are dependent upon the aware-
ness, concern, prudence, and proper training of personnel involved in the operation, trans
port, maintenance, and storage of the machine. Refer also to safety messages and opera-
tion instruction in each of the appropriate sections of the tractor and mower manuals. Pay
close attention to the safety signs affixed to the tractor and the rotary mower.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ROTARY MOWER ASSEMBLY INSTRUCTIONS
STEP 1
Place rotary mower on a flat, level surface. (See Figure A)
STEP 2
Remove the wired on PTO shaft, lift pins, and spacers. Loosen and remove the
(4) bolts on the lift arm brackets, that secure the lift arm support straps, lift arms,
and lift arm braces from the shipping positions and set aside. (See Figure B)
STEP 3
Install the right lift arm and lift arm support strap using (2) two short bolts and (1)
one lift pin. (See Figure C) Note: The lift arm support strap has one hole
punched larger than the other. The larger hole is to be used to fasten with the lift
pin. The lift arm & support straps should be fastened to the outside of the lift arm
bracket.
STEP 4
Loosen and remove the (2) nuts and washers for the A-frame tail wheel section,
leaving the bolts in place. (See Figure D)
STEP 5
Install both the right and left side lift arm braces by sliding them over the (2) two
A-frame tail wheel bolts that were loosened in step 4. Start the nuts on the
bolts, but at this time DO NOT TIGHTEN THEM. Allow the lift arm braces to ro-
tate forward and rest against the installed lift arm. (See Figure E)
STEP 6
Install the long top mounting bolt by inserting it through the hole in the left side
lift arm brace, the lower of the (2) two holes in the left side lift arm, the spacer,
the lower of the (2) two holes in the top of the right side lift arm (which should
not be attached to the lift arm bracket at this time), and finally through the right
side lift arm brace. Install a washer and start the nut on the bolt, but do not
tighten it at this time. (See Figure F,G & H) Note: You may have to move the
assembly around to start the nut & washer. If unable to get the nut and washer
started a "C" clamp may be necessary to compress the assembly to be able to
start the nut & washer. Install the swivel (U-Shaped piece) put mounting bolt
through upper hole in left lift arm, the spacer & swivel, (making sure the 1" block
on swivel is toward the front and rests against front side of the bottom spacer),
then through top hole of right lift arm, install a washer and start the nut on the
bolt, but do not tighten it at this time.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7
Using the right side lift arm as a lever, pull to the outside of the lift arm
bracket and inset bolt through lift arm and lift arm bracket. (See Figure I) Install
washer and nut. Place the lift pin in the larger of the (2) holes on the lift arm
brace and loosely attach the lift arm. Finally insert bolt, nut and washer to lower
section of lift arm support strap to lift arm bracket. (See Figure J)
STEP 8
Tighten all nuts and bolts.
Figure A
Figure B
Figure C
Figure D
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure E
Figure F
Figure G
Figure H
Figure I
Figure J
10
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE PUTTING ROTARY MOWER INTO SERVICE
(IMPORTANT-INSTRUCTIONS PRIOR TO START UP)
SHIPPED WITH OIL IN GEARBOX
SHIPPED WITHOUT GREASE IN GREASE FITTINGS.
UNIT MUST BE SERVICED BEFORE USING.
•
•
Use Multi-Purpose Gear Oil (I.E. S.A.E. 80w/90 or S.A.E. 85w/140 Multi-
purpose gear oil) in Gearbox.
For all Grease Fittings use TYPE/grade II tube grease.
STEP 1
STEP 2
Place rotary mower so that the deck is secure and level.
Remove 1/2” Pipe Plug (Located at top of gearbox) and 1/8” Pipe Plug
(located at lower 1/3 of gearbox) if oil comes out lower hole replace lower
plug immediately and continue to Step 4. If no oil comes out continue to
Step 3.
STEP 3
STEP 4
STEP 5
Fill gearbox using multi-purpose gear oil through top 1/2” fill hole until gear
oil is level with lower 1/8" hole.
Replace both the 1/2” pipe plug (located at top of gear box) and 1/8" pipe
plug (located at lower 1/3 of gear box) and clean away any excess oil.
Grease (with a grade II type tube grease),
The following zerks:
Tail wheel, wheel fork (See Figure M-1, page 22).
Tail wheel fork (See Figure M-1, page 22).
Both U-Joints on the PTO Shaft (See Figure M-2, page 22).
Inspect all guards to insure they are in good working order. If not replace
before using.
STEP 6
STEP 7
Check all bolts, nuts and belt to insure they are tight and secure.
CAUTION:
DO NOT over fill gearbox. This could cause damage to oil seals and can cause per-
manent damage to the gearbox. This issue will not be covered under warranty.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY TRAINING
Safety is a primary concern in the design and manufacture of our product. Un-
fortunately, our efforts to provide safe equipment can be wiped out by a single
careless act of an operator or bystander.
In addition to the design and configuration of equipment, hazard control and ac-
cident prevention are dependent upon the awareness, concern, prudence and
proper training of personnel involved in the operation, transport, maintenance
and storage of this equipment.
It has been said, “ The best safety device is an informed, careful operator.” We
ask you to be that kind of operator. It is the operator’s responsibility to read and
understand all safety and operating instructions in the manual and to follow
them. Accidents can be avoided.
Working with unfamiliar equipment can lead to careless injuries. Read this man-
ual, and the manual for your tractor, before assembly or operating, to acquaint
yourself with the machines. If this machine is used by any person other than
you, or is loaned or rented, it is the rotary mower owner’s responsibility to make
certain that owner's manual be available to the operator prior to operating:
1- Reads and understands the operator’s manuals.
2- Is instructed in safe and proper use.
Know your controls and how to stop tractor, engine, and the mower quickly in an
emergency. Read this manual and the one provided with your tractor.
Train all new personnel and review instructions frequently with existing workers.
Be certain only a properly trained and physically able person will operate the
machinery. A person who has not read and understood all operating and safety
instructions is not qualified to operate the machine. An untrained operator ex-
poses himself and bystanders to possible serious injury or death. If the elderly
are assisting with farm work, their physical limitations need to be recognized and
accommodated.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARTION
Never operate the tractor and mower until you have read and completely under-
stand this manual, the Tractor Operator’s Manual, and each of the safety mes-
sages found on the safety signs on the tractor and mower.
Personal protection equipment including hardhat, safety glasses, safety shoes, and gloves
are recommended during assembly, installation, operation, adjustment, maintenance, repair-
ing, removal, or moving the implement. Do not allow long hair, loose fitting clothing, or jewelry
to be around equipment.
PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE PERMANENT HEARING LOSS!
Tractors with or without mowers attached can often be noisy enough to cause permanent,
partial hearing loss. We recommend that you wear hearing protection on a full-time basis if
the noise in the operator’s position exceeds 80 db. Noise over 80 db on a long-term basis
can cause severe hearing loss. Noise over 90 db adjacent to the operator over a long-term
basis may cause permanent, total hearing loss. NOTE: Hearing loss from loud noise (from
tractors, chain saws, radios, and other such sources close to the ear) is cumulative over a life-
time without hope of natural recovery.
Operate the mower only with a tractor equipped with an approved Roll-Over-Protective Sys-
tem (ROPS). Always wear your seat belt. Serious injury of even death could result from fal-
ling off the tractor — particularly during a turnover when the operator could be pinned under
the ROPS or the tractor.
Clear area to be cut of stones, branches or other debris that might be thrown, causing injury
or damage.
Operate only in daylight or good artificial light.
Ensure mower is properly mounted, adjusted and in good operating condition.
Ensure that all safety shielding and safety signs are properly installed and in good condition.
STARTING AND STOPPING SAFETY
Check the tractor master shield over the PTO
dition and fastened securely to the tractor. Purchase a new shield if old shield is damaged or
missing.
All tractors that are not equipped with a “live” power takeoff (PTO) need to be equipped with
an over-running PTO clutch. These are available through most farm equipment stores.
NOTE: The addition of an over-running PTO clutch may change the length of the PTO drive-
line required. Pay extra attention to the instructions on the PTO driveline Installation. Be sure
that the driveline system guarding is adequate.
stub shaft. Make sure it is in good con-
Mower operating power is supplied from tractor PTO. Refer to your tractor manual for PTO
engagement and disengagement instructions. Know how to stop tractor and mower quickly in
case of an emergency.
When engaging PTO, the engine RPM should always be at idle speed. Once engaged and
ready to start cutting, raise PTO speed to 540 RPM and maintain throughout cutting opera-
tion.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL SAFETY
The use of this equipment is subject to certain hazards that cannot be protected
against by the mechanical means or product design. All operators of this equip-
ment must read and understand this entire manual, paying particular attention to
safety and operating instructions, prior to using. If there is something in this
manual you do not understand, ask your supervisor, or your dealer, to explain it
to you.
Most accidents occur because of neglect or carelessness. Keep all helpers and
bystanders at least several hundred feet from an operating rotary mower. Only
properly trained people should operate this machine.
When machine is operated in populated areas where thrown objects could injure
persons or property, operation must be stopped when anyone comes within
several hundred feet.
The majority of the accidents involve entanglement on the driveline, injury of by-
standers by the objects thrown by the rotating blades, and operators being
knocked off the tractor by low hanging limbs and then being run over by the
mower. Accidents are most likely to occur with machines that are loaned or
rented to someone who has not read the owner’s manual and is not familiar with
a rotary mower.
The rotary mower is designed for use only on tractors with 540-RPM power take
off.
Install and secure all guards and shields before starting or operating. The dis-
charge chute, bands, flaps, driveline guards and tractor, shields should be used
and maintained in good working condition. They should be inspected carefully,
at least daily, for missing or broken cable, chain links, shields, or guards. (Worn
items must be replaced at once to reduce possibility of injury)
Disengage power takeoff (PTO) and place transmission in neutral before at-
tempting to start engine.
Many varied objects, such as wire, cable, rope, or chains, can become entan-
gled in the operating parts of the mower. These items could then swing outside
the housing at greater velocities than the blades. Such a situation is extremely
hazardous. Inspect the cutting area for such objects before mowing. Remove
any like objects from the site.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL SAFETY continued...
Never allow the cutting blade to con-
tact such items. Cut material
higher at first, allowing rotary mower to clear hidden objects. Never assume an
area is clear. Always Check!
Always stop the tractor, disengage PTO, set brake, shut off the tractor engine,
remove the ignition key, lower implement to the ground and allow mower blades
to come to a complete stop before dismounting tractor. Never leave equipment
unattended with the tractor running.
Never place hands or feet under mower with tractor engine running or before
you are sure all motion has stopped. Stay clear of all moving parts.
Do not reach or place any part of your body under equipment until it is blocked
securely.
Do not allow riders on the rotary mower or tractor at anytime. There is no safe
place for any riders.
Do not operate unless all personnel, livestock, and pets are several hundred
feet away to prevent injury by thrown objects.
Never operate tractor and rotary mower under trees with low hanging limbs. Op-
erators can be knocked off the tractor and then run over by the rotating blades.
The rotating parts of this machine have been designed and tested for rugged
use. However, they could fail upon impact with heavy, solid objects such as steel
guardrails and concrete abutment. Such impact could cause the broken objects
to be thrown outward at very high velocities. To reduce the possibility of property
damage, serious injury, or even death, never allow the cutting blades to contact
such obstacles.
Stop mower and tractor immediately upon striking an obstruction. Turn engine
off, remove key, inspect and repair any damage before resuming operation.
Stay alert for uneven terrain, holes, rocks, and roots and other hidden hazards.
Keep away from drop-offs and hazards that could cause roll over.
Use extreme care and maintain minimum ground speed when transporting or
operating on hillsides, over rough ground and when operating close to ditches or
fences. Be careful and slow down when turning sharp corners and changing di-
rection on slopes. Do not start or stop suddenly on slopes. Avoid operation on
steep slopes. In extremely uneven terrain, rear wheels weights, front tractor
weight, and/or tire ballast should be used to improve stability.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL SAFETY continued...
Pass rotary mower diagonally through sharp dips and avoid sharp drops to pre-
vent “hanging up” tractor and rotary mower. Practice will improve your skills in
maneuvering on rough terrain. Always cut down slopes, never across the face.
Always check tractor manual for proper use on slopes.
When using a unit, a minimum 20% of tractor and equipment weight must be on
tractor front wheels. Without this weight, tractor could tip over, causing personal
injury or death. The weight may be attained with a front- end loader, front wheel
weights, ballast in the tires or front tractor weights. When attaining a minimum
20% of tractor and equipment weight on the front wheels, you must not exceed
the ROPS weight certification. Weigh the tractor and equipment. Do not guess
or estimate!
TRANSPORT SAFETY
Comply with state and local laws governing highway safety and movement of
farm machinery on public roads.
The use of flashing amber lights is acceptable in most localities. However, some
localities prohibit their use. Local laws should be checked for all lighting and
marking requirements.
At all times, when driving the tractor and equipment on the road or highway un-
der 20 mph (32 kph) use flashing amber warning lights and a slow moving vehi-
cle (SMV) identification emblem. Do not exceed 20 mph (32 kph). Reduce
speed on rough roads and surfaces.
Plan your route to avoid heavy traffic.
Always install transport locks, pins or brackets before transporting.
Do not drink and drive.
Be a safe and courteous driver. Always yield to oncoming traffic in all situations,
including narrow bridges, intersections, etc. Watch for traffic when operating
near or crossing roadways.
Turn curves or go up or down hills only at a low speed and at a gradual steering
angle. Make certain that a least 20% of the tractor’s weight is on the front
wheels to maintain safe steerage. Slow down on rough or uneven surface. Al-
ways check tractor manual for proper use on slopes.
Use extreme care and maintain minimum ground and when operating close to
ditches or fences. Be careful when turning sharp corners.
Never allow riders on either tractor or mower.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING TO TRACTOR
WARNING
Never stand between
tractor and rotary mower
while backing up tractor
to the hitch.
STEP 1 Attach to tractor's category 1 three point hitch as described in
the Tractor's Operator’s Manual.
WARNING
Failure to install retaining clip on gearbox input shaft would allow driveline to
swing freely if bolt is sheared causing possible injury or death.
STEP 2
Determine if the PTO shaft needs to be shortened.
NOTE:
Due to the many variations in the tractor hitch points and distances between
equipment gearbox input shaft and tractor PTO out put shafts, some combina-
tions may require PTO shafts to be shortened as described by the following
steps.
STEP 3
Raise and lower rotary mower in order to locate the shortest distance between
equipment gearbox input shaft and tractor PTO output shaft. With the rotary
mower in the shortest distance position shut down the tractor and SECURELY
BLOCK ROTARY MOWER IN POSITION.
STEP 4
Pull apart PTO shaft and attach outer section to tractor PTO output shaft.
NOTE: Be sure to pull on PTO shaft section to ensure yoke has locked into
place.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING TO TRACTOR continued....
STEP 5 Place and hold inner PTO shaft section next to outer section and
check if PTO shaft is too long. Each section should end approximately
3 inches short of reaching u-joint shield on the opposite section. If the
shaft is too long measure 3 inches back from each u-joint shield and
mark the other shaft section. Be sure to do this for both PTO shaft
halves. NOTE: Do not cut PTO shaft sections at this time.
STEP 6
Raise rotary mower and remove blocking. Raise and lower rotary mower in or-
der to locate the longest distance between equipment input shaft and the tractor
PTO output shaft. With the rotary mower in the longest distance position, shut
down the tractor and SECURELY BLOCK THE ROTARY MOWER IN POSI-
TION.
STEP 7
As in step 5 hold PTO shaft sections together and check for a minimum of 6
inches of overlap. If PTO shaft has been marked for cutting the overlap is the
distance measured between the two marks. If the PTO shaft has less than a 6
inch overlap, DO NOT USE. Contact your authorized King Kutter Dealer.
NOTE
If the PTO shaft length is too long go to SIZING PTO SHAFT (page 19)
STEP 8
Apply any multi-purpose grease to the outside of the male (inner) PTO shaft
section. Assemble PTO shaft and install on rotary mower and tractor.
NOTE: If you shear the bolt that attaches the PTO shaft to the gear box replace with a
grade 2 bolt only . Replacement with another grade of bolt will void your war-
ranty and may cause terminal damage to the PTO shaft, gearbox, or tractor.
(King Kutter shear pin 5 pack part #500101)
WARNING - Failure to install retaining clip on gearbox input shaft would allow
driveline to swing freely if bolt is sheared causing possible injury or
death.
STEP 9
Pull on tractor side of PTO shaft yoke to be sure it has locked in place. Make
certain PTO shaft shielding is in place and good working condition.
STEP 10
The PTO shaft shield is a non-rotating design and must be secured prior to
equipment use. Using the chain on each yoke shield attach to a fixed object on
the tractor and equipment ends that will not allow the PTO shaft shield to rotate
during operation.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SIZING PTO SHAFT
STEP 1
Cutting the PTO shaft to length. NOTE:
Be sure to cut equal lengths of each
PTO shaft section. Clamp end of PTO
shaft in a vice and cut off shield where
marked. (Figure 1-A & 1-B)
Figure 1-A
STEP 2
Using cut section of the shield as a
guide cut shaft off the same amount.
(Figure 2)
STEP 3
Repeat steps 1 and 2 for other PTO
shaft section.
STEP 4
Figure 1-B
Use a file to deburr PTO shafts. Clean
up all chips, burrs and filings from both
ends of the PTO shaft.
Note: If you shear the bolt that attaches
the PTO shaft to the gearbox re-
place with a grade 2 bolt only. Re-
placement with another grade of
bolt will void your warranty and may
cause terminal damage to the PTO
shaft, gearbox, or tractor.
Figure 2
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
This mower was designed to CUT PASTURE GRASS AND ROUGH AREAS UP TO 1"
IN DIAMETER.. Use of your rotary mower to cut any material larger than 1" in diame-
ter may damage the mower and void your warranty.
PRE-OPERATIONAL ADJUSTMENTS
Set tractor's lift control stop at a position that will prevent the PTO shaft from coming
in contact with the front edge of the mower when it is at full lift. Consult your tractor
manual for instructions.
CUTTING HEIGHT ADJUSTMENT
To prevent mower blades from striking the ground or hidden objects, your mower
should be set to the highest position that will give the desired cutting height. By setting
your mower up this way you reduce blade wear and stress to the mower. Mowing at
regular intervals will yield far better results than periodic mowing (i.e. less wind row-
ing). To adjust cutting heights follow these steps.
STEP 1
Raise rotary mower off the ground with the tractor and SECURELY
BLOCK IN POSITION. Remove 5/8" bolt from adjusting bracket. (See
Figure K)
STEP 2
Move the A-frame tail wheel up or down to desired cutting height. Rein
stall 5/8" bolt and tighten to secure in position. (See Figure L)
Note: It may be necessary to loosen the A-frame tail wheel attachment
bolts. (See Figure D, page 9)
Figure K
Figure L
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: For best results in heavier cutting conditions adjust the deck so the rear of
the mower is approximately 2" higher than the front. This method requires less horse-
power and ground speeds of approximately 3-5mph. If finer shredding results are de-
sired, adjust the deck to level or slightly lower in the rear. This method will keep foli-
age under the deck longer resulting in finer pieces. The down side of this method is if
it takes a lot more horsepower and very slow ground speed. This method is not rec-
ommended unless a PTO speed of 540 RPM can be maintained.
ROTARY MOWER OPERATION
STEP 1
Before each use perform the maintenance described in maintenance section. (page
22)
STEP2
Read, understand, and follow the information on safety training, preparation, starting
and stopping safety, operational safety, transport safety warning sections of this man-
ual (pages 11 thru 16)
STEP 3
With tractor running, lower rotary mower into working position.
STEP 4
With the tractor at idle RPM, engage PTO and slowly advance throttle to 540 PTO
RPM. NOTE: Rotary mower designed to run at 540 PTO RPM only.
STEP 5
Select a low gear for the tractor and begin to mow. Tractor ground speed is to be
controlled by gear selection only and not engine speed. Tractor ground speed should
allow rotary mower to maintain 540 PTO RPM and thus maximum blade tip speed.
NOTE: Do not allow the tractor engine or rotary mower to bog down or stall. This
causes undue wear and tear on the mower and tractor. If this continues to happen re-
duce ground speed and raise cutting height of rotary mower until the 540 PTO RPM is
able to be maintained.
Never attempt to clean out a plugged discharge chute until the tractor has
been shut down and the mower blades have completely stopped.
STEP 6
After each use clean all debris from the top and bottom of the rotary mower. Re-
place any missing or illegible safety decals. Inspect for any damaged or worn parts
and replace before next use. Store rotary mower in a dry environment.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1). Periodically check and maintain proper gear oil level.
2). Every 8 hours, wheel fork (s), wheel hub (s), PTO shaft universal joints (2), and
PTO telescoping surface. (See Figures M-1 & M-2)
NOTE: Use only a grade Type II tube grease.
3). Before each use check to make sure all safety features are installed and work-
ing properly.
4). Keep blades sharp and balanced at all times. When replacing blades, replace
all blades and blade bolts at the same time.
5). Periodically check all nuts and bolts to insure they are tight and secure.
Figure M-1
(grease points
Figure M-2
(U-joints)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE SAFETY
Good maintenance is your responsibility. Poor maintenance is an invitation to trouble.
Follow good shop practices.
Keep service area clean and dry
Be sure electrical outlets and tools are properly grounded
Use adequate light for the job at hand.
Make sure there is plenty ventilation. Never operate the engine of the towing vehicle
in a closed building. The exhaust fumes may cause asphyxiation.
Before working on this machine, disengage the PTO, shut off the engine, set the
bakes, and remove the ignition keys.
Be certain all moving parts on attachments have come to a complete stop before at-
tempting to perform maintenance.
Never work under equipment unless it is blocked securely.
Always use personal protection devices such as eye, hand and hearing protectors,
when performing any service or maintenance.
Frequently check mower blades. They should be sharp, free of nicks and cracks and
securely fastened.
Periodically tighten all bolts, nuts, and screws and check that all cotter pins are prop-
erly installed to ensure unit is in safe condition.
When completing a maintenance or service function, make sure all safety shields and
devices are installed before placing unit in service.
After servicing, be sure all tools, parts and service equipment are removed from
mower.
Do not allow debris, grease or oil to build up on any deck or platform.
Where replacement parts are necessary for periodic maintenance and servicing, genu-
ine factory replacement parts must be used to restore your equipment to original
specifications.
The manufacturer will not be responsible for injuries or damages caused by use of un-
approved parts and/or accessories.
A fire extinguisher and the first aid kit should be kept readily accessible while perform-
ing maintenance on this equipment.
STORAGE SAFETY
Following operation, or when unhooking the mower, stop the tractor, set the brakes,
disengage the PTO, shut off the engine and remove the ignition keys.
Store the unit in an area away from human activity.
Do not park equipment where it can be exposed to direct contact to livestock for long
periods of time. Damage and livestock injury could result.
Make sure all parked machines are on a hard, level surface and engage all safety de-
vices.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY SIGN LOCATIONS
The types of safety signs and locations on the equipment are shown in the illustration
below. Good safety requires that you familiarize yourself with the various safety signs,
the type of warning and the area, or particular function related to that area, that re-
quires your SAFTY AWARENESS
REMEMBER: If safety signs have been damaged, removed, become illegible or parts
have been replaced without signs, new safety signs must be applied. New safety
signs are available from your authorized dealer, distributor or factory.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
1
25
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
27
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7
MODEL NO.
DESCRIPTION
SN# XXXXXXXXXX
8
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SHEAR PIN PTO SHAFT
Ref.
No.
Part Name
147022
147029
147034
1
2
Roll Pin Kit
500131
151045
500131
151045
500133
151065
Male Tube End Yoke
3
4
Implement End Yoke
Female Tube End Yoke
Tractor End Yoke
151040
151050
151035
151090
151091
170015
170110
124310
124311
151040
151050
151035
151090
151091
170015
170110
124310
124311
151060
151070
151055
151092
151093
170020
170110
124315
124316
5
6
Inner Tube 14 Series
Outer Tube 14 Series
Cross Kit # 4
7
8
9
Quick Disconnect Pin
Safety Shield BYPY
Safety Shield Eurocardan
10
10
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SLIP CLUTCH PTO SHAFT
Ref.
No.
Part Name
147129
147134
170020
170120
151070
151092
147248
170020
170120
151070
151092
1
2
3
4
Cross Kit
Roll Pin
170015
170120
151050
151090
Female Tube End Yoke
Inner Tube
5
6
Slip Clutch Assembly
Male Tube End Yoke
Outer Tube
-
-
-
151045
151091
151035
170110
124310
151065
151093
151055
170110
124315
151065
151093
151055
170110
124315
7
8
Tractor End Yoke
Quick Disconnect Pin
Safety Shield BYPY
9
10
10
Safety Shield Eurocardan
124311
124316
124316
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SLIP CLUTCH ASSEMBLY
Ref.
No.
Part Name
7”
8”
1
2
3
4
5
6
7
8
Clutch Spring with Compression Bolts (Pkg 8)
Flanged Yoke
500140
196006
196005
196008
196004
147350
196002
196001
500140
196011
196005
196003
196007
147350
195998
196015
Sleeve
Clutch Plate
Friction Hub
Slip Clutch Lock Bolt
Slip Clutch Liner Plate
Pressure Plate
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ROTARY MOWER- LIFT
Ref.
No.
Part Name
Part Number
5-1/2’-
5-1/2’-
60hp
6’-
40hp
40”-40hp 4’- 40hp 5’- 40hp 5’- 60hp
40hp
6’- 60hp
Rotary Mower Size
Tire & Rim /w Hub
1
2
3
403001 403001 403001 403001 403001 403001 403001 403001
403019 403019 403019 403019 403019 403019 403019 403019
191100 191100 191100 191100 191100 191100 191100 191100
Wheel Fork Assembly
Wheel Hub Assembly
A-Frame Assembly
A-Frame Height Adjust.
Gear Box Slick
4
5
401022 401018 401019 401019 401017 401017 401020 401020
310081 310081 310081 310081 310081 310081 310081 310081
184000 184000 184005 184060 184005 184060 184005 184060
6
Gear Box Splined
Lift Arm Brace
6
-
-
184010 184065 184010 184065 184010 184065
7
310075 310076 310074 310074 310079 310079 310073 310073
147022 147022 147029 147029 147034 147034 147034 147034
PTO Shaft /w Shear Pin
PTO Shaft /w Slip Clutch
8
8
-
-
147129 147129 147134 147134 147134 147134
Lift Arms
9
310087 310088 310088 310088 310091 310091 310091 310091
500001 500001 500001 500001 500001 500001 500001 500001
Cat. 1 Lift Pins (Pk. 2)
Lift Arm Support Strap
Blade Carrier*
10
11
12
13
14
15
16
17
-
310071 310071 310071 310071 310071 310071 310071
403030
-
-
-
-
-
-
-
-
Stump Jumper*
403031 403031 403031 403031 403032 403031 403032
Blade Bolt Set (Pkg.2)
Blade Set (Pkg. 2)
Swivel Kit**
501001 501001 501001 501001 501001 501001 501001 501001
501118 501118 501124 501124 501127 501127 501130 501130
-
501027 501027 501027 501027 501027 501027 501027
Wheel Washer Kit
501013 501013 501013 501013 501013 501013 501013 501013
500101 500101 500101 500101 500101 500101 500101 500101
Shear Bolt Kit (Pkg. 5)
18
19
1” Castle Nut Pkg. 501110 501110 501110 501110 501110 501110 501110 501110
32
Download from Www.Somanuals.com. All Manuals Search And Download.
5’ HEAVY DUTY LIFT MOWER
Ref.
No.
Part Name
Part
Number
5’- 60hp
5’- 80hp
Rotary Mower Size
Tire & Rim /w Hub
1
2
3
501000
403602
191200
501000
403602
191200
Wheel Fork Assembly
Wheel Hub Assembly
A-Frame Assembly
A-Frame Height Adjust.
Gear Box
4
5
401023
310081
184065
310080
147134
403656
500002
403455
403041
501002
501224
310974
501280
401023
310081
184080
310080
147134
403656
500002
403455
403041
501002
501224
310974
501280
6
Lift Arm Brace
PTO Shaft
7
8
Lift Arm Assembly
Cat. 2 Lift Pins (Pkg. 2)
Swivel Yoke Assembly
Blade Carrier
9
10
11
12
13
14
15
16
Blade Bolt Set (Pkg.2)
Mower Blade Set (Pkg.2)
Lift Pin Plate
Axle Bolt & Nut
Castle Nut & Cotter Pin
17
501110
501110
33
Download from Www.Somanuals.com. All Manuals Search And Download.
HEAVY DUTY LIFT 6’ & 7’ MOWER
Ref.
No.
Part Name
Part
Number
7’ - 60hp
7’ - 80hp
6’- 60hp
6’- 80hp
Rotary Mower Size
1
2
3
Tire & Rim /w Hub
Wheel Fork Assembly
Wheel Hub Assembly
501000
403602
191200
501000
403602
191200
501000
403602
191200
501000
403602
191200
4
5
Cross Axle Assembly
Gear Box
403600
184065
310619
147134
403658
403402
500002
195170
403041
501002
501230
-
403600
184080
310619
147134
403658
403402
500002
195170
403041
501002
501230
-
403601
184065
310609
147248
403658
403402
500002
195170
403033
501002
501230
501002
501110
403601
184080
310609
147248
403658
403402
500002
195170
403033
501002
501230
501002
501110
6
Lift Arm Brace
7
PTO Shaft
8
Lift Arm Assembly
Swivel Yoke Assembly
Cat. 2 Lift Pins (Pkg. 2)
Ratchet Jack
9
10
11
12
13
14
15
16
Blade Carrier
Blade Bolt Set (Pkg.2)
Mower Blade Set (Pkg.2)
Axle End 7’
Castle Nut & Cotter Pin
501110
501110
34
Download from Www.Somanuals.com. All Manuals Search And Download.
ROTARY MOWER– PULL
Ref.
No.
Part Name
Part
Number
5’- 60hp
6’- 40hp
6’- 60hp
6’- 80hp
4’- 40hp
5’- 40hp
Rotary Mower Size
1
2
3
Tire & Rim /w Hub
Cross Axle Assembly
Wheel Hub Assembly
403001 403001 403001 403001 403001 430001
403548 403560 403560 403564 403564 403564
191100 191100 191100 191100 191100 191100
4
5
Top Link CAT. 1
Gear Box
195166 195166 195166 195166 195166 195166
184005 184005 184060 184005 184060 184080
147029 147148 147148 147148 147148 147248
403648 403648 403648 403648 403648 403648
320160 320160 320160 320160 320160 320160
403031 403031 403032 403031 403032 403032
501001 501001 501001 501001 501001 501001
501118 501124 501124 501130 501130 501130
501101 501101 501101 501101 501101 501101
501110 501110 501110 501110 501110 501110
501280 501280 501280 501280 501280 501280
6
PTO Shaft
7
Pull Tongue Assembly
Axle Cuff
8
9
Stump Jumper
10
11
12
13
14
Blade Bolt Set (Pkg.2)
Mower Blade Set (Pkg.2)
Shear Bolt Kit (Pkg. 5)
Castle Nut & Cotter Pin
Axle Bolt & Nut
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ROTARY MOWER– 7’ PULL
Ref.
No.
Part Name
Part Number
P-84-60-HD P-84-80-HD
Rotary Mower Size
1
2
Tire & Rim /w Hub
Cross Axle Assembly
Wheel Hub Assembly
Ratchet Jack
501000
403568
191100
195170
184065
147248
403658
320160
403403
403033
501002
501000
403568
191100
195170
184080
147248
403658
320160
403403
403033
501002
3
4
5
Gear Box
6
PTO Shaft
7
Pull Tongue Assembly
Axle Cuff
8
9
Swivel Yoke Assembly
Blade Carrier
10
11
Blade Bolt Set (Pkg.2)
12
13
13
14
Mower Blade Set (Pkg.2)
Shear Bolt Kit (Pkg. 5)
Castle Nut & Cotter Pin
Axle Bolt & Nut
501230
501101
501110
501280
501230
501101
501110
501280
36
Download from Www.Somanuals.com. All Manuals Search And Download.
PTO SHAFTS COVER REMOVAL
BONDIOLI- (BYPY)
(Pictures are on next page)
1). There are 3 white tabs around the cover as shown in (A in FIG. 1). Take a
screwdriver and press against the tabs one at a time with downward angular
pressure toward the end of shaft marked (B in FIG. 2). As you are pressing tab
grasp cover at point marked (B in FIG. 2) and apply pressure against cover in
the direction of arrow, do this for each tab. (Sometimes the other tabs may
relock, if they do you must repeat unlock procedure.) You will feel it click when
the tab releases, after all 3 tabs are released you can slide the cover down the
shaft in direction of (C in FIG. 2).
2) To put cover back into place slide cover back toward end until all the tabs relock.
(You may have to tap lightly with screwdriver or hammer handle).
NOTE: Cover may be longer on some models but, they will come off the
same as above.
EUROCARDAN SERIES 4
1)
First you must locate the black tab (D in FIG. 3) put flat screwdriver in slot in
end of tab and turn until the flat side is pointing towards center of shaft. Once
you do this take the thin flat screwdriver and put into slot labeled (E in FIG. 3)
pry tab all the way out as shown in (FIG. 3)
2). There are 3 white tabs around the cover as shown in (G in FIG. 4). You must
line up cover slots and tabs (as shown in FIG. 4, F & G) Take a screwdriver
and press against the tabs one at a time with downward angular pressure to-
ward the end of shaft. As you are pressing tab grasp cover and apply pressure
against cover in the direction of arrow, (H in FIG-3) do this for each tab.
(Sometimes the other tabs may relock, if they do you must repeat unlock proce-
dure.) You will feel it click when the tab releases, after all 3 tabs are released
you can slide the cover down the shaft in direction of (H in FIG. 3).
3)
To put cover back into place slide cover back toward end (be sure tabs and slots
line up) until all the tabs relock. (You may have to tap lightly with screwdriver or
hammer handle). Once they have relocked replace black tab that was removed
with flat side toward shaft center then turn flat side up to lock in place.
LA MAGDALENA
1)
2)
There are 3 black tabs around the cover (K in FIG. 5). Take a screwdriver and
press against the tabs one at a time with downward angular pressure toward the
end of shaft marked (J in FIG. 5). As you are pressing tab grasp cover at point
marked (J in FIG. 5) and apply pressure against cover in the direction of arrow,
do this for each tab.
To replace slide cover back toward end and line up black tabs with the holes and
lock in place.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
BONDIOLI COVER REMOVAL
FIGURE- 1
FIGURE - 2
EUROCARDAN SERIES 4 COVER REMOVAL
FIGURE - 3
FIGURE - 4
LA MAGDALENA COVER REMOVAL
FIGURE - 5
38
Download from Www.Somanuals.com. All Manuals Search And Download.
PTO SHAFTS COVER REMOVAL
EUROCARDAN SERIES 5
1). There are 2 black tabs around the cover as shown in (B in FIG. 1). Take a flat
screwdriver and pry under the tabs one at a time at point (B in FIG. 2) lifting tab
over on top of (e-shaped lock). After both tabs are released you can slide the
locking ring down the shaft in direction of (C in FIG. 3). Then you will see a
metal e-ring (E in FIG. 4) at point (D in FIG. 4) you must pry under ring and re-
move it, (it will just slide down shaft unless you take PTO apart) then apply pres-
sure against cover (A in FIG. 1) in the direction of arrow and slide cover down
shaft.
2) To put cover back into place slide cover back toward end, making sure cover and
locking mechanism (F in FIG. 4) line up. Replace metal e-ring, slide the locking
ring back into place, be sure the tabs lock securely over locks.
NOTE: Cover may be longer on some models but, they will come off the
same as above.
FIGURE- 1
FIGURE– 2
FIGURE– 4
FIGURE– 3
39
Download from Www.Somanuals.com. All Manuals Search And Download.
40 HP GEARBOX
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Ref.
No.
Part Name
Gearbox
184000
Gearbox
184005
Gearbox
184010
1
2
Snap Ring
Input Seal (NAK 35 x 54 x 10)
Front Cap
106138
156010
129015
124130
106138
156010
129015
124130
131031
131030
155005
185010
186010
155010
129010
185006
131045
156005
124131
129005
501110
131035
131040
106138
156010
129015
124130
131031
131030
155005
185010
186005
155010
129010
185006
131045
156005
124131
129005
501110
131035
131040
3
4
Front Cap Gasket
Snap Ring
5
6
Snap Ring
131030
155005
185007
186010
155010
129010
185005
-
7
Bearing (Hoover 208)
Input Gear
8
9
Input Shaft
10
11
12
13
14
15
16
17
18
19
Bearing (NSK 6207)
Housing
Output Shaft
Spacer
Output Seal (NAK 40 x 54 x 7)
Bottom Cap Gasket
Bottom Cap
156005
124131
129005
501110
131035
131040
1’ Castle Nut /w Washer & Cotter Pin
1/2” Pipe Plug
1/8” Pipe Plug
20
3/8” x 1” Bolt & Lock washer
-
-
-
41
Download from Www.Somanuals.com. All Manuals Search And Download.
60 HP GEARBOX
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Ref.
No.
Part Name
Gearbox
184060
Gearbox
184065
1
2
Input Seal (NAK 35 x 60 x 10)
End Cap Input
156040
129025
124133
155015
155020
131050
185015
186020
129020
185035
156040
129025
124133
155015
155020
131050
185026
186015
129020
185035
3
Gasket Input
4
Bearing Race Input (Timken LM603014)
Bearing Input (Timken LM603049)
Spacer 1/4”
5
6
7
Input Gear
8
Input Shaft
9
Housing
10
Gear Output
11
12
13
14
15
16
17
18
19
20
Bearing Race Output (Timken 363)
Bearing Output (Timken 368)
Output Shaft
155035
155040
186022
124134
156035
129030
501110
131035
131040
-
155035
155040
186022
124134
156035
129030
501110
131035
131040
-
Gasket Output
Seal Output (TCM 50 x 68 x 9 TC)
End cap Output
1’ Castle Nut /w Washer & Cotter Pin
1/2” Pipe Plug
1/8” Pipe Plug
3/8” x 1” Bolt & Lock washer
Download from Www.Somanuals.com. All Manuals Search And Download.
80 HP GEARBOX
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Ref.
No.
Part Name
Gearbox
184080
1
2
1/2” Vented Pipe Plug
Input Seal (NAK SC 35 x 60 x 10)
1/8” Pipe Plug
131035
156040
131040
129025
124133
155015
155020
-
3
4
End Cap Input
5
Gasket Input
6
Bearing Race Input (Timken LM603014)
Bearing Input (Timken LM603049)
Spacer
7
8
9
Input Gear
185015
131025
186040
185035
155037
155040
186035
155036
124134
156035
129030
501110
10
11
12
13
14
15
16
17
18
19
20
Snap Ring
Input Shaft
Gear Output
Bearing Race Output (Timken 362A)
Bearing Output (Timken 368)
Output Shaft
Bearing Race Output (Timken 362)
Gasket Output
Seal Output (TCM 50 x 68 x 9 TC)
Endcap Output
1’ Castle Nut /w Washer & Cotter Pin
45
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Limited Warranty.
King Kutter, Inc. (“King Kutter”), P.O. Box 1200, Winfield, Alabama 35594, warrants to the original retail pur-
chaser (“Purchaser”) that the product that is the subject of this sale is free from defects in material and work-
manship at the time of sale.
Under this warranty, King Kutter will repair the defective product free of charge to the Purchaser, with either
new or used and reconditioned replacement parts. All warranty service will be performed at service centers
designated by King Kutter. If King Kutter is unable to repair the product to conform to the warranty after a
reasonable number of attempts, King Kutter will provide, at its option, one of the following: (a) a replacement
for the product or, (b) a full refund of the purchase price. Repair, replacement, or refunds are the Pur-
chaser’s EXCLUSIVE remedies against King Kutter under this limited warranty. King Kutter will not be liable
for any special, incidental or consequential damages based upon breach or warranty, breach of contract, neg-
ligence, strict tort liability, or any other legal theory. Such damages include, but are not limited to, loss of prof-
its, loss of savings or revenue, loss of use of the product or any associated equipment, cost of capital, cost of
any substitute equipment, facilities or services, down time, the claims of third parties including customers, and
injury to property. These limitations also apply, to the extent allowed by law, to personal injury.
The purchaser must notify the Seller in writing of any defect in material or workmanship within one (1) year
following the date of purchase. If the equipment is used for commercial purposes, the Purchaser must notify
the Seller in writing of any defect in material or workmanship within ninety (90) days following the date of pur-
chase. In no event will King Kutter be liable under this warranty unless written notice is received by the Seller
within one (1) year from the date of original retail sale.
2. Warranty of Title.
King Kutter warrants that it transfers a good title to the product free of any encumbrances, and free of the
rightful claim of any third party for infringement of patent or copyright.
3. What is Not Covered by This Limited Warranty.
King Kutter will not be responsible for damage to or failure in the product which results from accident, misuse,
abuse, neglect, installation of attachments not provided by King Kutter, modifications to the product, or dam-
age caused by use of the product for purposes other than those for which it was designed.
4. No Other Warranties.
Unless modified in writing and signed by both parties, this agreement is understood to be the complete and
exclusive agreement and warranty between King Kutter and Purchaser, superseding all prior agreements,
oral and written, and all other communication between King Kutter and Purchaser related to the subject mat-
ter of this agreement.
THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUD-
ING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE IMPLIED
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. No employee of King Kutter nor anyone else is
authorized to make any warranty or representation in addition to or different from those made in this agree-
ment.
5. Allocation of Risk.
This agreement allocates the risk of product failure between King Kutter and the Purchaser. This Allocation is
recognized by both parties as reflected in the price of the goods. The Purchaser acknowledges that he or she
has read this agreement, understands it, and is bound by its terms.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|