Husqvarna Lawn Sweeper 45 0352 User Guide

2007-08  
Operators  
Manual  
O0707001  
42 Inch  
Lawn Sweeper  
(45-0352)  
Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REF. QTY. DESCRIPTION  
REF. QTY. DESCRIPTION  
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
2
1
1
4
1
4
6
2
1
6
1
21  
2
6
2
1
4
2
Hex Bolt, 5/16-18 x 3" Lg.  
T
U
V
W
X
1
6
1
2
2
2
1
2
4
1
1
2
1
1
2
1
Hair Cotter Pin, Large  
Hair Cotter Pin, Small  
Cotter Pin, 1/8" x 3/4"  
Clevis Pin, 3/8" x 1/2"  
Clevis Pin, 1/4" x 1-1/8"  
Clevis Pin, 1/4" x 1-3/4"  
Spacer, Small  
Spacer, Hitch  
Hopper Mount Clamp  
Angle Bracket  
Grip  
Vinyl Cap  
Hitch Pin  
Spring, Hitch Pin  
Plastic Plug  
Hex Bolt, 5/16-18 x 2-1/2" Lg.  
Hex Bolt, 5/16-18 x 2-1/4" Lg.  
Hex Bolt, 5/16-18 x 1-3/4" Lg.  
Hex Bolt, 5/16" x 1-1/4"  
Hex Bolt, 5/16" x 1"  
Hex Bolt, 5/16" x 3/4"  
Curved Head Bolt, 5/16" x 1-5/8"  
Carriage Bolt, 3/8" x 1"  
Screw, #10-32 x 5/8"  
Nylock Nut, 3/8"  
Nylock Nut, 5/16"  
Hex Nut, 5/16"  
Nylock Nut, #10-32  
Palnut  
Washer, 7/16"  
Y
Z
AA  
BB  
CC  
DD  
EE  
FF  
GG  
HH  
II  
Extension Spring  
Washer, 5/16"  
Lock Washer, 5/16"  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 4 - CONNECT HITCH TUBES  
6. Fasten the hitch tubes together using two 5/16" x 3" hex  
bolts and 5/16" nylock nuts. Do not tighten yet. See  
figure 2.  
ASSEMB
L
Y
O
F SWEEPER  
TOOLS REQUIRED FOR ASSEMB
L
Y  
(1) Knife or Scissors  
(1) Screwdriver  
(1) Hammer  
5/16" x 3"  
HEX BOLT  
(1) 3/8" Open End or Box End Wrench  
(2) 1/2" Open End or Box End Wrench  
(1) 3/8" Open End or Box End Wrench  
STEP 1 - REMOVE PARTS FROM CARTON  
1. To protect painted parts, lay them on cardboard or a  
mat.  
2. Remove the sweeper housing, the loose parts and the  
hardware package from the carton. Lay out the parts  
and hardware as shown on pages 3 and 4.  
5/16" NYLOCK NUT  
STEP 2 - INSTALL HITCH TUBES  
FIGURE 2  
3. The hitch tubes are stamped with a "77L" for the left tube  
and a "76R" for the right tube. The sweeper housing is  
marked with an "L" on the left side and an "R" on the  
right side. See figure 1.  
4. Holdthelefthitchtubeagainsttheleftsideofthesweeper  
sothatthe"77L"onthetubefacesawayfromthesweeper.  
Attach the hitch tube using two 5/16" x 1-3/4" hex bolts  
and 5/16" nylock nuts. Repeat for the right hitch tube,  
but with the "76R" facing in toward the right side of the  
sweeper. Do not tighten yet. See figure 1.  
STEP 5 - ASSEMBLE HITCH PIN  
7. Assemblethehitchpinbracket,thehitchspringandthen  
the 7/16" flat washer onto the hitch pin. Secure them to  
the hitch pin with a 1/8" x 3/4" cotter pin placed into the  
middle hole in the hitch pin. Spread ends of cotter pin  
around hitch pin. See figure 3.  
8. Assemble the hitch pin bracket to the straight hitch  
bracket using a 3/8" x 1" carriage bolt and a 3/8" nylock  
nut. Align the brackets and tighten. See figure 3.  
STEP 3 - REMOVE PLASTIC TIE  
5. Removetheplastictiethatfastenstheheightadjustment  
tube to the front of the sweeper housing. See figure 1.  
3/8" x 1" CARRIAGE BOLT  
1/8" x 3/4" COTTER PIN  
HITCH BRACKET  
(STRAIGHT)  
5/16" x 1-3/4"  
HITCH PIN  
BRACKET  
5/16" NYLOCK NUT  
HEX BOLT  
HOUSING  
MARKED "L"  
7/16" FLAT WASHER  
HITCH SPRING  
3/8" NYLOCK NUT  
MIDDLE HOLE  
HITCH PIN  
PLASTIC TIE  
TUBE  
MARKED  
FIGURE 3  
"77L"  
HITCH TUBE (L.H.)  
FIGURE 1  
STEP 6 - MEASURE TRACTOR HITCH  
9. If your tractor hitch measures 10" or more above the  
ground go to STEP 7a. If your tractor hitch measures  
less than 10" above the ground go to STEP 7b  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 8 - TIGHTEN BOLTS  
STEP 7a - ASSEMBLE HITCH BRACKETS  
(For tractor hitches 10" or more above the ground.)  
10. Placethebenthitchbracketontopofthehitchtubesand  
placethestraighthitchbracketwithhitchpinunderneath  
the hitch tubes. Fasten together using a 5/16" x 2-1/2"  
hex bolt (front), a 5/16" x 2-1/4" hex bolt (rear) and two  
5/16" nylock nuts as shown in figure 4.The bolts should  
straddle the front hitch tube bolt.
Do not tighten yet.  
14. At this time tighten the four bolts in figure 1 that fasten  
the hitch tubes to the sweeper housing. Next, tighten  
the two bolts in figure 2 that fasten the ends of the hitch  
tubes together. Finally, tighten the two bolts in figure 4  
or 5 that fasten the hitch brackets to the hitch tubes.  
STEP 9 - ASSEMBLE THE ANGLE BRACKET  
15. Assemble the angle bracket to the sweeper housing  
using two 5/16" x 3/4" hex bolts and 5/16" nylock nuts.  
The upright portion of the angle bracket should face  
toward the left side of the sweeper. See figure 6.  
11. Assemble the two hitch spacers onto the hitch pin and  
secure the pin with the large hairpin cotter. See figure 4.  
5/16" NYLOCK NUT  
5/16" x 2-1/4"  
5/16" x 2-1/2"  
HEX BOLT  
ANGLE  
BRACKET  
HEX BOLT  
LARGE  
HAIRPIN  
COTTER  
5/16" x 3/4"  
HEX BOLT  
HITCH  
BRACKET  
(BENT)  
HITCH  
SPACERS  
HITCH BRACKET  
(STRAIGHT)  
HITCH PIN  
BRACKET  
5/16" NYLOCK NUTS  
FIGURE 4  
FIGURE 6  
STEP 7b - ASSEMBLE HITCH BRACKETS  
(For tractor hitches less than 10" above the ground.)  
12. Place the bent hitch bracket underneath the hitch tubes  
and place the straight hitch bracket with hitch pin on  
top of the hitch tubes. Fasten together using a 5/16" x  
2-1/2" hex bolt (front), a 5/16" x 2-1/4" hex bolt (rear)  
and two 5/16" hex lock nuts as shown in figure 5. The  
bolts should straddle the front hitch tube bolt. Do not  
tighten yet.  
STEP 10 - ASSEMBLE HEIGHT ADJUST  
HANDLE  
16. Assemble the plastic grip onto the upper height adjust  
handle. See figure 7.  
17. Fastentheupperandlowerheightadjusthandlestogether  
as shown in figure 7. Use one 5/16" x 1" hex bolt, one  
5/16" x 1-1/4" hex bolt, two 5/16" washers and two 5/16"  
nylock nuts. Place the washers against the slots in the  
upper handle.Tighten the nuts and then loosen 1/2 turn  
so that the handles slide easily. See figure 7.  
13. Assemble the two hitch spacers onto the hitch pin and  
secure the pin with the large hairpin cotter. See figure 5.  
5/16" x 2-1/4"  
5/16" x 2-1/2"  
5/16" x 1-1/4" HEX BOLT  
PLASTIC GRIP  
HEX BOLT  
HEX BOLT  
HITCH PIN  
BRACKET  
HITCH  
BRACKET  
(STRAIGHT)  
5/16" WASHER  
HITCH  
SPACERS  
5/16" NYLOCK NUT  
5/16" x 1" HEX BOLT  
HITCH  
5/16" NYLOCK NUTS  
BRACKET  
5/16" WASHER  
LARGE HAIRPIN COTTER  
FIGURE 7  
FIGURE 5  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 11 - ASSEMBLE EXTENSION SPRING  
18. Assemble a 5/16" x 1" hex bolt and a 5/16" nylock nut  
into the top hole in the height adjustment handles. See  
figure 8.  
STEP 13 - ATTACH HEIGHT ADJUST STRAP  
TO ANGLE BRACKET  
21. Place the height adjust strap between the angle bracket  
andtheheightadjustmenthandle.Attachtheheightadjust  
strap to the angle bracket using a 5/16" x 1" hex bolt,  
the small spacer, a 5/16" washer and a 5/16" nylock nut.  
Tighten. See figure 10.  
19. Assemble the extension spring onto the end of the upper  
bolt and the middle bolt in the height adjust handles.  
Assemble a 5/16" nylock nut onto each bolt so that one  
thread of the bolt extends through the nut. See figure 8.  
5/16" x 1" HEX BOLT  
SPACER (SMALL)  
5/16" WASHER  
5/16" x 1" HEX BOLT  
5/16" NYLOCK NUT  
HEIGHT ADJUST  
STRAP  
5/16" NYLOCK NUT  
EXTENSION SPRING  
5/16" NYLOCK NUT  
FIGURE 8  
FIGURE 10  
STEP 12 - ATTACH HEIGHT ADJUST HANDLE  
20. Assemble the height adjust handles to the height  
adjustment tube on the front of the sweeper housing.  
Use two curved head bolts, bowed washers, 5/16" lock  
washers and 5/16" hex nuts. Do not tighten yet. See  
figure 9.  
STEP 14 - ATTACH HEIGHT ADJUST STRAP  
TO HEIGHT ADJUST HANDLE  
22. Attach the height adjust strap to the height adjust handle  
using a 5/16" x 1" hex bolt, 5/16" washer and 5/16" nylock  
nut.Place the washer against the slot in the height adjust  
strap.Tighten the nut and then loosen 1/2 turn so that the  
strap can slide freely. See figure 11.  
23. Slide the height adjust handle so that it aligns with the  
height adjust strap and the angle bracket. Tighten the  
height adjustment handle in place. See figure 11.  
5/16" HEX NUT  
5/16" LOCK  
WASHER  
5/16" WASHER  
5/16" NYLOCK NUT  
BOWED  
WASHER  
5/16" x 1"  
HEX BOLT  
CURVED  
HEAD BOLT  
HEIGHT  
ADJUSTMENT  
TUBE  
FIGURE 9  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 16 - ASSEMBLE LOWER TUBES  
4. Assemble the two lower hopper tube together using a  
plastic plug. See figure 15.  
ASSEMB
L
Y
O
F HOPPER BAG  
STEP 15 - ASSEMBLE UPPER TUBES  
1. Insertthelefthandupperhoppertubethroughthestitched  
flaps of the hopper bag, starting at the center cut out  
in the top of the bag. See figures 12, 13 and 14. Repeat  
for the right hand upper hopper tube.  
PLASTIC PLUG  
UPPER HOPPER TUBE  
(LEFT HAND SHOWN)  
LOWER  
HOPPER  
TUBE  
CENTER CUT OUT  
(START HERE)  
BAG FLAP  
FIGURE 15  
Right  
Left  
END HERE  
5. Placetheassembledlowerhoppertubesintothebottom  
of the hopper bag and then slide the tubes to the back  
of the bag. See figure 16.  
FIGURE 12  
6. Attach the ends of the lower hopper tubes to the inside  
of the upper hopper tubes using two 3/8" x 1/2" clevis  
pins inserted from the inside, and two small hair cotter  
pins. See figure 16.  
2. Slide the two upper hopper tubes together and line up  
the center holes as shown in figure 13.  
UPPER HOPPER TUBES  
UPPER HOPPER  
TUBE  
SMALL HAIR  
COTTER PIN  
LOWER HOPPER TUBE  
FIGURE 13  
3/8" x 1/2"  
CLEVIS PIN  
3. Fasten the upper hopper tubes together using a plastic  
plug. See figure 14.  
PLASTIC PLUG  
HOPPER BAG  
BOTTOM  
FIGURE 16  
FIGURE 14  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 18 - ATTACH BAG SIDES  
9. Fold the bag flaps around the lower hopper tubes and  
attach to the bag bottom using the snaps. See figure  
19.  
STEP 17 - ATTACH BAG BOTTOM  
7. Assemblethebagretainerandthebagframestraptothe  
front edge of the bag bottom. Place the bag retainer on  
top and the bag frame strap underneath the bag bottom.  
Fasten together using six #10 x 5/8" screws and #10-32  
nylock nuts. See figure 17.  
FRONT EDGE OF BAG BOTTOM  
FRAME STRAP  
FLAP  
SNAP  
#10-32 x 5/8" SCREW  
BAG RETAINER  
#10-32  
NYLOCK NUT  
FIGURE 17  
FIGURE 19  
STEP 19 - ASSEMBLE SUPPORT RODS  
IMPORTANT: Do not over bend the support rods during  
thefollowingstep.Overbendingwilldecreasethesupporting  
tension of the rods.  
8. Assemble the bag frame strap to the holes in the lower  
hopper tubes using two 1/4" x 1-1/8" clevis pins and  
small hair cotter pins. See figure 18.  
10. Assemble the two hopper support rods as shown in  
figure 20. Place the ends of the rods into the holes in  
the upper and lower hopper tubes, flexing the rod just  
enough to fit into the holes in the tubes.  
BAG FRAME STRAP  
SMALL HAIR  
COTTER PIN  
CLEVIS PIN (N)  
SUPPORT  
RODS  
FIGURE 18  
FIGURE 20  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 20 - ASSEMBLE HOPPER ROD,TUBES  
VINYL CAP  
5/16" NYLOCK NUT  
5/16" x 3/4"  
HEX BOLT  
AND CLAMPS  
11. If the hole in the side of the upper hopper tubes is  
covered over by the bag, locate the hole by touch. It is  
approximately midway along the side of the bag. Pierce  
holes through the stitched bag flaps where the holes in  
both hopper tubes are located. See figure 21.  
UPPER HOPPER TUBE  
PALNUT  
MOUNTING CLAMP  
FIGURE 23  
STEP 21 - ATTACH ROPE  
16. Secure the rope to the center of the upper rear hopper  
tube as shown in figure 24.  
FIGURE 21  
12. Slide the hopper bag pivot rod through the hole in an  
upper hopper tube. Assemble a mounting clamp, two  
bag arm tubes and another mounting clamp onto the  
rod as shown in figure 22. Push the rod on through the  
upper hopper tube on the opposite side of the bag.  
PIVOT ROD  
FIGURE 24  
STEP 22 - ATTACH HOPPER BAG  
17. To attach the hopper bag to the sweeper, slide the ends  
of the bag arm tubes into the ends of the hitch tubes  
and secure with two 1/4" x 1-3/4" clevis pins and small  
hairpin cotters. See figure 25.  
MOUNTING CLAMP  
BAG ARM TUBE  
FIGURE 22  
BAG ARM TUBE  
13. Assemble the two remaining hopper mount clamps onto  
the pivot rod on the outside of the bag. Fasten them to  
the inside clamps using four 5/16" x 3/4" hex bolts and  
5/16" nylock nuts. Tighten securely. See figure 23.  
14. Assemble two palnuts onto the ends of the pivot rod by  
lightly tapping them with a hammer. See figure 23.  
15. Place a vinyl cap onto each bag arm tube. See figure 23.  
1/4" X 1-3/4"  
CLEVIS PIN  
SMALL  
HAIRPIN  
COTTER  
HITCH TUBE  
HITCH TU
HINT: To ease assembly of the palnuts, place the bag on  
its side on a hard surface. With the bottom end of the  
pivot rod against the surface, tap a palnut onto the top  
end of the rod. Repeat for other end of rod.  
FIGURE 25  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 22 - ATTACH SWEEPER TO TRACTOR  
BRUSH HEIGHT ADJUSTED  
APPROXIMATELY MID-WAY  
1. Place the tractor and sweeper on a flat level surface.  
2. Set the sweeper height adjustment handle to about the  
middle of its adjustment range.  
3. Attach the sweeper hitch to the tractor hitch, arranging  
the hitch spacers in one of six possible combinations as  
shown in GROUP A and GROUP B diagrams below.  
IMPORTANT:
To obtain the best performance from your  
sweeper, arrange the spacers so that the sweeper bag is  
approximately level with the ground and approximately 5" to  
7" off the ground as shown in figure 26.  
APPROXIMATELY LEVEL  
(5" to 7" FROM SURFACE)  
FIGURE 26  
GROUP "A"
 
- For
 
vehicles with hitches  
having 8" to 10" ground clearance.  
GROUP "B"
 
- For
 
vehicles with hitches  
having 10" to 13" ground clearance.  
HITCH BRACKET MOUNTED  
ABOVE HITCH TUBES  
HITCH BRACKET MOUNTED  
BELOW HITCH TUBES  
BLACK LINE IS TRACTOR HITCH  
BLACK LINE IS TRACTOR HITCH  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOWYOUR SWEEPER  
WINDSCREEN  
HEIGHT  
ADJUSTMENT  
HANDLE  
HOPPER  
ROPE  
PIVOT ROD  
BAG ARM  
TUBE  
HHEIGHT  
AADJUSSTMENT  
SSTRAP  
HITCH  
BRACKETS  
HOPPER BAG  
Hopper Bag  
Collects grass clippings, leaves and debris.  
Hopper Rope  
Permits dumping of hopper bag from driver's seat.  
Windscreen  
Helps prevent collected material from being blown out of hopper bag.  
Connects the hopper bag to the sweeper housing.  
Bag Arm Tubes  
Pivot Rod  
Allows hopper bag to tilt forward to dump material.  
Height Adjustment Handle  
Height Adjustment Strap  
Hitch Bracket  
Adjusts the operating height of the sweeper.  
Holds the height adjustment handle in position when locked.  
Connects the sweeper to the towing vehicle. Adjusts for various height tractor hitches.  
HOW TO US
E
Y
OUR SWEEPER  
DUMPING OF SWEEPER  
BRUSH HEIGHT ADJUSTMENT  
3. Your sweeper can be dumped easily without getting off  
of the tractor. Pull the rope forward to dump the hopper.  
Always empty hopper after each use.  
1. To adjust your sweeper brushes to the best operating  
height, lift up on the height adjustment handle to  
disengage it from the height adjustment strap.Move the  
handle forward or backward to raise or lower the brush.  
Seegure26.Bestadjustmentiswhenthebrushsetting  
is 1/2" down into the grass. Always mow the grass to an  
even height before sweeping.  
CAUTION:
Never attach
the hopper rope to any  
part of your body or clothing!
Never hold onto
the  
rope while towing the sweeper! Attach the rope  
to the towing vehicle to keep it away from wheels  
and rotating parts.  
SWEEPING SPEED  
2. Tryastartingspeedofapproximately3m.p.h.(thirdgear  
on most tractors). Depending on the conditions, it may  
be necessary to adjust the sweeping speed in order to  
achieve best results.  
CAUTION: Keep sweeper away from fire.  
Excessive heat can damage the brushes and  
hopper bag and could cause the bag and its  
contents to burn.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CLEANING  
MAINTENANCE  
6. Clean sweeper housing with a soft brush or cloth.  
7. Clean debris from hopper bag with a brush or broom.  
8. Remove any material which has wrapped around  
brushes or ends of brush shaft.  
SCHEDULED MAINTENANCE  
1. Clean the sweeper after each use.  
2. Inspect for worn or damaged parts, such as brushes  
and wheels.  
3. Lubricate the brush shaft bearing twice a year with a  
few drops of light weight oil. See figure 27.  
HEIGHT ADJUSTMENT SLOT  
OIL BEARINGS HERE  
FLAT WASHER  
STORAGE  
CAUTION: Before storing the sweeper,  
always empty the hopper bag to avoid  
spontaneous combustion.  
HEX BOLT  
FIGURE 27  
1. Clean the sweeper and hopper bag thoroughly to help  
prevent rust and mildew.  
2. To collapse the hopper bag for storage, remove the two  
hopper support rods from the rear of the hopper.  
3. Store in a dry area.  
4. Lubricate the wheel bearings each season.Remove the  
hub cap and apply a few drops of light weight oil.  
5. Everytwoyears, removethewheelsandcleanthegears  
found inside the wheel housing.After cleaning, lubricate  
the gears with an even coat of light grease. To remove  
the wheel, pop off the hub cap and remove the lock nut,  
flat washer and hub cap washer. See figure 28.  
HEX BOLT  
FLAT WASHER  
FLAT WASHER  
HUB CAP  
SPACER  
HUB CAP  
WASHER  
NYLOCK NUT  
FIGURE 28  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
IMPORTANT: Do not remove both wheels at the same  
time to avoid mixing of parts. (The R.H. and L.H. ratchet  
gears are not interchangeable.) Make notes on the position  
of washers and snap rings during disassembly.  
BRUSH REPLACEMENT  
NOTE: Brush replacement should be done one brush at  
a time.  
1. Remove only one wheel from the sweeper.  
2. Remove the retaining rings and washers which hold the  
ratchet gear onto the brush shaft.  
3. Remove the gear by sliding it off the brush shaft. (Look  
for the drive pin, which may fall out of the brush shaft  
when the ratchet gear is removed.) See figure 30.  
4. Toreassemble, insertthedrivepinthroughtheholenear  
the end of the brush shaft.Make sure the pin slides back  
and forth easily in the shaft. See figure 30.  
1. Remove the hopper bag from the sweeper.  
2. Loosen only the two hex bolts and lock nuts which clamp  
one brush in a brush retainer.Do not loosen or remove  
the bolts which fasten the brush retainers to the brush  
shaft. See figure 29.  
3. Lift the brush out of the retainers, noting on which side  
of the brush the bristles overlap. See figure 29.  
4. Install new brush, making sure the bristles overlap on  
the same side of the brush as before. See figure 29.  
5. Tighten the two hex bolts and lock nuts to clamp the  
new brush in place before removing the next brush.  
5. Lightly grease the shaft and fill the ratchet gear with  
grease. Assemble the ratchet gear back onto the shaft.  
See figure 30.  
6. Lightly grease the axle and the gear teeth on the wheel,  
and then reassemble the wheel. The brushes should  
rotate only during forward rotation of the wheel. If the  
brushesaredriven(rotated)bybothforwardandreverse  
rotation of the wheel, the drive pin is jamming in the  
ratchet gear. Disassemble to clean and lubricate the  
drive pin and the ratchet gear. See figure 30.  
BRUSH ROTATION  
7. Remove the second wheel and repeat the procedure.  
OVERLAP  
BRISTLES  
BRUSH  
RETAINER  
RATCHET  
GEAR  
OVERLAP  
BRISTLES  
DO NOT  
REMOVE  
OVERLAP  
BRISTLES  
DRIVE  
PIN  
FIGURE 29  
FIGURE 30  
TROUBLESHOOTING  
Wheels skid when sweeping.  
1. Brushes set too low.  
2. Brushes are jammed  
1. Adjust height till brushes are 1/2"  
down into grass.  
2. Stop sweeper. Remove obstruction.  
3. Removeonewheelatatimetocheck  
for obstruction or damage. Refer to  
Service and Adjustments section.  
3. Wheels are jammed.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS FOR MODEL 45-0352, 45-0352-669 - 42" PROFESSIONAL LAWNSWEEPER  
83  
40  
82  
85  
43  
41  
86  
62  
46  
54  
83  
82  
53  
62  
38  
88  
19  
45  
20  
44  
53  
47  
81  
12  
81  
89  
55  
86  
42  
3
56  
17  
84  
37  
39  
13  
20  
20  
64  
15  
67  
A
14  
19  
C
19  
20  
78  
7
16  
35  
9
10  
8
36  
E
C
D
1
22  
31  
58  
72  
77  
22 30  
28  
24  
5
B
11  
25  
37  
27  
26  
29  
60  
59  
57  
27  
18  
6
87  
D
32  
21  
34  
73  
23  
26  
74  
75  
50  
76  
55  
4
86  
61  
17  
69  
51  
70  
49  
71  
2
64  
20  
64  
A
20  
65  
B
64  
66  
20  
63  
32  
63  
48  
20  
52  
E
68 79  
80  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS FOR MODEL 45-0352, 45-0352-669 - 42" PROFESSIONAL LAWNSWEEPER  
REF.  
NO.  
PART  
NO.  
QTY.  
DESCRIPTION  
REF.  
NO.  
PART  
NO.  
QTY.  
DESCRIPTION  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
43938  
43737  
24864  
23687  
24192  
24865  
24866  
46781  
46823  
49308  
49306  
23684  
46782  
43224  
44292  
43084  
44481  
43081  
43063  
43840  
43000  
25407  
43086  
43943  
23368  
43343  
46816  
44230  
43352  
142  
2
1
1
1
1
1
1
2
1
2
2
1
2
1
1
4
2
4
2
1
1
1
2
1
2
1
1
1
1
1
1
1
2
2
2
4
2
2
2
2
6
2
6
6
1
Rod, Hopper Support 34"  
Hopper Rope  
Strap, Height Adjustment  
Bracket, Hitch  
Bracket, Hitch (Straight)  
Handle, Upper Height Adjustment  
Handle, Lower Height Adjustment  
Tube, Bag Arm  
Rod, Hopper Bag Pivot  
Wheel & Tire Ass'y. (with bearings)  
Wheel Bearing  
1
2
3
4
5
6
7
8
46776  
46777  
64753  
9M5732  
46778  
24186  
63463  
1629-56  
44232  
64733  
49152  
25138  
48557  
43661  
47189  
25137  
1540-31  
47046  
43182  
47810  
44911  
141  
1
1
1
6
1
1
1
2
2
2
8
1
6
12  
12  
12  
4
Hitch Tube, R.H.  
Hitch Tube, L.H.  
Housing Assembly  
Rivet  
Skirt, 42"  
Retainer, Skirt  
Height Adjustment Tube Ass'y.  
Retainer, Dust Cover  
Ball Bearing  
Brush Bushing Ass'y.  
Rivet  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
Bracket, Hitch Pin  
Brush Shaft  
Brush, 42"  
Bolt, Hex 5/16-18 x 3" Lg.  
Bolt, Hex 5/16-18 x 2-1/4" Lg.  
Bolt, Hex 5/16-18 x 2-1/2"  
Bolt, Hex 5/16-18 x 1-3/4" Lg.  
Cap, Vinyl  
Bolt, Hex 1/4-20 x 1" Lg.  
Nut, Nylock 1/4-20 Thread  
Brush Retainer  
Washer, Flat .78" x 1.25" x .06"  
Dowel Pin (Drive)  
Bolt, Hex 5/16-18 x 3/4" Lg.  
Nut, Nylock 5/16-18 Thread  
Spacer, .41" x 1.125" x .50"  
Washer, Flat 1-1/2" x .375" x .062"  
Washer, .849" x .598" x .025"  
Washer, Special  
Spacer, .78" x 1.25" x .50"  
Ring, Retaining .594"  
Washer, Shim 1-1/8" x .594" x .025"  
Nut, Nylock 3/8-24 Thread  
Hub Cap  
Washer, Hub Cap  
Bolt, Hex 3/8-24 x 3-1/4" Lg.  
Spacer, Small  
Gear, Pinion R.H. (not shown)  
Gear, Pinion L.H.  
Bolt, Hex 1/4-20 x 5/8"  
Lock Washer, 1/4"  
Washer, Flat 5/16"  
2
Bolt, Hex 5/16-18 x 1"  
Bolt, Hex 5/16-18 x 1-1/4"  
Spring, Extension  
Angle Bracket  
Lock Washer, 5/16"  
Grip, Height Adjust  
Spacer, Hitch  
Hairpin Cotter, 1/8"  
Pin, Hitch  
10  
25  
2
4
2
2
2
4
6
2
2
2
2
3
1
1
4
4
2
1
1
1
1
1
1
44006  
23336  
46219  
1650-21  
44007  
1038  
Spring, Hitch Pin  
Washer, 7/16" Flat  
43014  
25440  
44961  
23400  
48652  
48651  
43866  
43177  
64559  
46732  
46733  
46734  
46735  
46738  
46739  
25430  
24190  
Pin, Cotter 1/8" x 3/4" Lg  
Bolt, Carriage 3/8-16 x 1"  
Nut, Nylock 3/8-16  
Bolt, Cvd. Hd. 5/16-18 x 1-5/8" Lg.  
Washer, Bowed 1" x .32" x .06"  
Nut, Hex 5/16-18 Thread  
Hopper Mount Clamp  
Palnut, 3/8"  
43350  
77 HA21362  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
44947  
44695  
43083  
23331  
44917  
48402  
48365  
48366  
43055  
46867  
43346  
47171  
48959  
Dust Cover Assembly  
Lower Hopper Tube, R.H.  
Lower Hopper Tube, L.H.  
Upper Hopper Tube, R.H.  
Upper Hopper Tube, L.H.  
Hopper Bag  
Wind Screen  
Strap, Bag Frame  
Retainer, Bag  
Plug, 1/4"  
Pin, Clevis 1/4" x 1-1/8"  
Pin, Clevis 3/8" x 1/2"  
Hairpin Cotter, 3/32" #3  
Pin, Clevis 1/4" x 1-1/2" Lg.  
Screw, #10-32 x 5/8" Truss Head  
Nut, Nylock #10-32  
1
1
Owners Manual  
the fastest way to purchase parts www.speedepart.com  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
the fastest way to purchase parts www.speedepart.com  
REPAIR PARTS  
Agri-Fab, Inc.  
809 South Hamilton  
Sullivan, IL. 61951  
217-728-8388  
© 2005 Agri-Fab, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Craftsman Lawn Mower 24728901 User Guide
Ferris Industries Lawn Mower 1000ZKAV21 48 User Guide
Kunz Lawn Mower MR55B User Guide
Poulan Lawn Mower 186996 User Guide
Scag Power Equipment Lawn Mower SW36 BJ User Guide
Snapper Lawn Mower 1600178 User Manual
Snapper Lawn Mower 1690226 User Guide
Snapper Lawn Mower SPV211S User Manual
Snapper Lawn Mower SPV22675HW User Manual
Snapper Lawn Mower YT12D User Manual