Note: To maintain compliance with FCC Rules and Regulations, cables
connected to this device must be shielded cables.
UL Statement
UL listed: UL60950-1 for I.T.E. product safety.
Canada
Industry Canada ICES-003
This Class A digital apparatus complies with Canadian ICES-003 emissions.
Conformité à la règlementation canadienne
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du
Canada.
cUL Statement
cUL listed: CSA C22.2 No.60950-1-03 for I.T.E. product safety.
Europe
The CE mark indicates compliance to 2004/108/EC EMC Directive
with Standards EN55022 CLASS A, EN55024, EN61000-3-2,
EN61000-3-3. In addition, complies to 2006/95/EC Low Voltage
Directive, when shipped with recommended power supply.
For further information please contact:
Hand Held Products
Nijverheidsweg 9-13
5627 BT Eindhoven
The Netherlands
Hand Held Products, Inc. shall not be liable for use of our product with
equipment (i.e., power supplies, personal computers, etc.) that is not CE
marked and does not comply with the Low Voltage Directive.
Waste Electrical and Electronic Equipment Information
Hand Held Products complies with Directive 2002/96/EC OF THE
EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on
waste electrical and electronic equipment (WEEE).
This product has required the extraction and use of natural resources for its
production. It may contain hazardous substances that could impact health
and the environment, if not properly disposed.
In order to avoid the dissemination of those substances in our environment
and to diminish the pressure on the natural resources, we encourage you to
use the appropriate take-back systems for product disposal. Those systems
will reuse or recycle most of the materials of the product you are disposing in
a sound way.
The crossed out wheeled bin symbol informs you that the product
should not be disposed of along with municipal waste and invites you to use
the appropriate separate take-back systems for product disposal.
If you need more information on the collection, reuse, and recycling systems,
please contact your local or regional waste administration.
You may also contact your supplier for more information on the
environmental performances of this product.
Germany
GS Mark Applicable if GS logo is marked on product to indicate
meeting geprufte Sicherheit approval.
Australia/NZ
C-Tick Statement
Conforms to AS/NZS 3548 EMC requirements.
Korea (4600r only)
M
I
C
MIC Class A EMC requirements.
Mexico
Applicable if NOM logo is marked on product.
International
Eye Safety Statement
LED
This device has been tested in accordance with IEC60825-1 LED safety, and
has been certified to be within the limits of a Class 1 LED device.
Solids and Water Protection
The 4600g/4600r/4600rp has a rating of IP41, immunity of foreign particles
and dripping water tested to Standard EN60259.
The 4800i has a rating of IP54, immunity of windblown dust penetration and
splashing water tested to Standard EN60259.
CB Scheme
Certified to IEC60950-1 I.T.E. Product Safety.
Patents
Please refer to the product packaging for a list of patents.
USB HID...................................................................... 1-10
RS-232 Serial Port Connection........................................... 1-11
Keyboard Country ................................................................ 2-4
Keyboard Style ..................................................................... 2-6
Keyboard Modifiers.............................................................. 2-7
RS-232 Baud Rate........................................................ 2-10
RS-232 Word Length: Data Bits, Stop Bits, and Parity2-11
RS-232 Receiver Time-Out.......................................... 2-12
RS-232 Handshaking ................................................... 2-12
Wand Emulation Connection....................................... 2-13
i
Wand Emulation................................................................. 2-14
Delay Between Blocks................................................. 2-14
Chapter 3 - Output
User-Specified Reread Delay ............................................... 3-9
LED Power Level ................................................................. 3-9
Illumination Lights ............................................................... 3-9
Imager Time-Out ................................................................ 3-10
Aimer Delay........................................................................ 3-10
User-Specified Aimer Delay........................................ 3-11
Aimer Mode........................................................................ 3-11
ii
Output Sequence Editor................................................ 3-19
Multiple Symbols................................................................ 3-20
Suffix Selections............................................................. 4-4
Intercharacter, Interfunction, and Intermessage Delays ....... 4-5
Data Format Editor Introduction........................................... 5-1
To Add a Data Format.................................................... 5-1
Other Programming Selections ...................................... 5-2
Data Format Editor Commands...................................... 5-2
Data Format Editor......................................................... 5-5
Data Formatter................................................................ 5-5
Alternate Data Formats .................................................. 5-6
iii
Data Block Size.............................................................. 6-5
Secondary Trigger Mode...................................................... 6-6
Manual/Serial Trigger.................................................... 6-6
Hands Free Time-Out ........................................................... 6-7
Scan Stand Mode.................................................................. 6-8
Scan Stand Symbol ........................................................ 6-8
Presentation Mode ................................................................ 6-8
iv
UPC-A Number System ............................................... 7-20
UPC-A Addenda........................................................... 7-21
UPC-A Addenda Required........................................... 7-21
UPC-A Addenda Separator .......................................... 7-21
UPC-E0 ........................................................................ 7-22
UPC-E0 Expand ........................................................... 7-22
UPC-E0 Addenda Required ......................................... 7-23
UPC-E0 Addenda Separator......................................... 7-23
v
Kix (Netherlands) Post................................................. 7-43
Australian Post ............................................................. 7-43
Australian Post Interpretation ...................................... 7-44
Japanese Post................................................................ 7-44
China Post Message Length......................................... 7-45
Korea Post Message Length......................................... 7-46
QR Code Message Length ........................................... 7-47
vi
Image Snap - IMGSNP ......................................................... 8-2
Image Ship - IMGSHP.......................................................... 8-6
OCR Check Character........................................................... 9-8
OCR Modulo 36 Check Character ................................. 9-9
Weighting Options ....................................................... 9-10
OCR ISBN Application Example ....................................... 9-12
OCR Template Codes ......................................................... 9-13
Chapter 10 - Interface Keys
Keyboard Function Relationships....................................... 10-1
Supported Interface Keys.................................................... 10-3
vii
Chapter 11 - Utilities
Test Menu........................................................................... 11-3
2D PQA Reporting....................................................... 11-3
Query Commands......................................................... 12-2
Responses..................................................................... 12-2
4600g and 4600r ................................................................. 13-1
4800i ................................................................................... 13-2
Standard Cable Pinouts....................................................... 13-4
Keyboard Wedge.......................................................... 13-4
Wand Emulation........................................................... 13-5
Serial Output ............................................................... 13-6
USB.............................................................................. 13-7
viii
Maintenance........................................................................ 14-1
For Further Information................................................ 15-2
Product Service and Repair................................................. 15-2
Online Product Service and Repair Assistance ............ 15-3
Limited Warranty................................................................ 15-3
Symbology Chart ................................................................. A-1
ASCII Conversion Chart (Code Page 1252)........................ A-4
Code Page Mapping of Printed Barcodes ............................ A-6
ix
x
1
Getting Started
About This Manual
This User’s Guide provides installation and programming instructions for the
4000 Series imagers. Product specifications, dimensions, warranty, and
customer support information are also included.
Hand Held Products barcode imagers are factory programmed for the most
common terminal and communications settings. If you need to change these
settings, programming is accomplished by scanning the barcodes in this guide.
An asterisk (*) next to an option indicates the default setting.
Unpacking the Imager
After you open the shipping carton, take the following steps:
•
Check for damage during shipment. Report damage immediately to the
carrier who delivered the carton.
•
•
Make sure the items in the carton match your order.
Save the shipping container for later storage or shipping.
4600rp, 4600g/4600r, 4800i User’s Guide
1 - 1
Imager Models
The chart below lists the interfaces that can be used with your imager. Refer to
Chapter 6 for programming information regarding secondary interfaces.
Models
Primary
Secondary
4600gXX03XX
4800iXX03XX
True RS-232
True RS-232
4600gXX05XX
4800iXX05XX
Keyboard wedge, TTL level
232, TTL level 232 serial
wedge, IBM 4683, wand emu-
lation, USB keyboard, USB
HID, USB retail (IBM Sure-
POS), USB COM port emula-
tion
Wand Emulation, TTL
level 232
4600rXX05XX
4600rpXX05XX
Keyboard wedge, TTL level
232, TTL level 232 serial
wedge, IBM 4683, USB key-
board, USB HID, USB retail
(IBM SurePOS), USB COM
port emulation
TTL level 232
TTL level 232
Keyboard wedge, TTL level
232, TTL level 232 serial
wedge, IBM 4683, USB key-
board, USB HID, USB retail
(IBM SurePOS), USB COM
port emulation
1 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
Connecting the Imager with Keyboard Wedge
Note: See "Imager Models" on page 1-2 to determine which interfaces apply to
your imager.
An imager can be connected between the keyboard and PC as a “keyboard
wedge,” plugged into the serial port, or connected to a portable data terminal in
wand emulation or non decoded output mode. The following is an example of a
keyboard wedge connection:
1. Turn off power to the terminal/computer.
2. Disconnect the keyboard cable from the back of the terminal/computer.
3. Connect the appropriate interface cable to the imager and to the terminal/
computer.
5. Program the imager for a keyboard wedge interface using the Plug and Play
barcodes beginning on page 1-8.
6. Verify the imager operation by scanning a barcode from the Sample
Symbols in the back of this manual. The imager beeps once.
Your imager is factory programmed for a keyboard wedge interface to an IBM PC
AT with a USA keyboard. If this is your interface and you do not need to modify
the settings, skip to Chapter 3 - Output.
1 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
Connecting the Imager with USB
Note: See "Imager Models" on page 1-2 to determine which interfaces apply to
your imager.
An imager can be connected to the USB port of a computer.
1. Connect the appropriate interface cable to the imager first, then to the com-
puter.
2. Program the imager for a USB interface using the Plug and Play barcodes
beginning on page 1-9.
3. The imager beeps.
4. Verify the imager operation by scanning a barcode from the Sample Symbols
in the back of this manual.
Products “USB Application Note,” available at www.handheld.com.
4600rp, 4600g/4600r, 4800i User’s Guide
1 - 5
Connecting the Imager with RS-232 Serial Port
Note: See "Imager Models" on page 1-2 to determine which interfaces apply to
your imager.
1. Turn off power to the terminal/computer.
2. Connect the appropriate interface cable to the imager.
Note: For the imager to work properly, you must have the correct cable for your
type of terminal/computer.
3. Plug the serial connector into the serial port on your computer. Tighten the
two screws to secure the connector to the port.
4. Plug the power supply into the cable.
5. Once the imager has been fully connected, power up the computer.
6. Program the imager for an RS-232 Serial Port interface using the Plug and
Play barcode on page 1-11.
1 - 6
4600rp, 4600g/4600r, 4800i User’s Guide
Connecting the Imager with RS-232 Wedge
Note: See "Imager Models" on page 1-2 to determine which interfaces apply to
your imager.
Your imager uses True and TTL signal levels to wedge into an RS-232 serial
network. Use only serial wedge cables to prevent damage to the imager. Refer
to RS-232 Baud Rate on page 2-10 to set the baud rate and communications
protocol.
1. Turn off power to the computer.
2. Disconnect the existing serial cable from the computer.
3. Connect the appropriate interface cable to the imager.
Note: For the imager to work properly, you must have the correct cable for your
type of computer.
Host
Terminal
4. Plug the serial connector into the serial port on your computer. Tighten the
two screws to secure the connector to the port.
5. Plug the other serial connector into the host connection and tighten the two
screws.
6. Plug the power pack cable into the receptor on the imager cable.
7. Plug the power pack into a power source.
8. Once the imager has been fully connected, power up the computer.
4600rp, 4600g/4600r, 4800i User’s Guide
1 - 7
9. To set up the serial wedge terminal ID, use the serial terminal ID 050 and
follow the instructions on page 2-1.
10. Program the port for data transmission using the barcodes on page 1-12.
Programming the Interface - Plug and Play
Plug and Play barcodes provide instant imager set up for commonly used
interfaces.
Note: After you scan one of the codes, power cycle the host terminal to have the
interface in effect.
Note: See "Imager Models" on page 1-2 to determine which interfaces apply to
your imager.
Keyboard Wedge Connection
If you want your system programmed for an IBM PC AT and compatibles
keyboard wedge interface with a USA keyboard, scan the barcode below.
Keyboard wedge is the default interface.
IBM PC AT and Compatibles
with CR suffix
Laptop Direct Connect
For most laptops, scanning the Laptop Direct Connect barcode allows
operation of the imager in parallel with the integral keyboard. The following
Laptop Direct Connect barcode also programs a carriage return (CR) suffix, and
turns on Emulate External Keyboard (page 2-7).
Laptop Direct Connect
with CR suffix
1 - 8
4600rp, 4600g/4600r, 4800i User’s Guide
USB Connection
IBM SurePos
Scan one of the following “Plug and Play” codes to program the imager for IBM
SurePos (USB Hand Held imager) or IBM SurePos (USB Tabletop imager).
Note: After scanning one of these codes, you must power cycle the cash
register.
IBM SurePos
(USB Hand Held Imager)
Interface
IBM SurePos
(USB Tabletop Imager)
Interface
Each barcode above also programs the following suffixes for each symbology:
Symbology
EAN-8
Suffix
0C
EAN-13
16
UPC-A
0D
UPC-E
0A
Code 39
Interleaved 2 of 5
Code 128
00 0A 0B
00 0D 0B
00 18 0B
4600rp, 4600g/4600r, 4800i User’s Guide
1 - 9
USB PC or Macintosh® Keyboard
Scan one of the following codes to program the imager for USB PC Keyboard or
USB Macintosh Keyboard. Scanning these codes adds a CR and selects the
terminal ID (USB PC Keyboard - 124, USB Macintosh Keyboard - 125).
USB Keyboard (PC)
USB Keyboard (Mac)
USB Japanese Keyboard (PC)
USB HID
Scan the following code to program the imager for USB HID barcode imagers.
Scanning this code changes the terminal ID to 131.
USB HID Barcode Imager
USB COM Port Emulation
The driver will use the next available COM port number. Apple® Macintosh
computers recognize the imager as a USB CDC class device and automatically
use a class driver. Scanning the code below changes the terminal ID to 130.
USB COM Port Emulation
Note: No extra configuration (e.g., baud rate) is necessary.
1 - 10
4600rp, 4600g/4600r, 4800i User’s Guide
CTS/RTS Emulation
On
* Off
ACK/NAK Mode
On
* Off
RS-232 Serial Port Connection
All communication parameters between the imager and terminal must match for
correct data transfer through the serial port using RS-232 protocol. Scanning the
RS-232 interface barcode programs the imager for an RS-232 interface at
38,400 baud, parity–none, 8 data bits, 1 stop bit, and adds a suffix of a CR LF.
RS-232 Interface
4600rp, 4600g/4600r, 4800i User’s Guide
1 - 11
Serial Wedge Data Transmission Port
Using the following barcodes, set the port to which you want the scanned data to
transmit. Port 1 corresponds to P1 on the output cable and Port 2 corresponds
to P2 on the output cable. Choosing Both sends scanned data to P1 and P2.
Default = P1.
* P1
Both P1 and P2
IBM 4683 Ports 5B, 9B, and 17 Connection
Note: See "Imager Models" on page 1-2 to determine which interfaces apply to
your imager.
Scan one of the following “Plug and Play” codes to program the imager for IBM
4683 Port 5B, 9B, or 17.
Note: After scanning one of these codes, you must power cycle the cash
register.
IBM 4683 Port 5B Interface
IBM 4683 Port 9B
HHBCR-1 Interface
IBM 4683 Port 17 Interface
1 - 12
4600rp, 4600g/4600r, 4800i User’s Guide
Each of the previous barcodes also programs the following suffixes for each
symbology:
Symbology
EAN-8
Suffix
0C
EAN-13
16
UPC-A
0D
UPC-E
0A
Code 39
Interleaved 2 of 5
Code 128
00 0A 0B
00 0D 0B
00 0A 0B
.
IBM 4683 Port 9B HHBCR-2 Interface
The IBM 4683 Port 9B HHBCR-2 Interface barcode also programs the following
suffixes for each symbology:
Symbology
EAN-8
Suffix
0C
EAN-13
16
UPC-A
0D
UPC-E
Code 39
Interleaved 2 of 5
Code 128
00 0A 0B
00 0D 0B
00 18 0B
Wand Emulation Connection
Note: See "Imager Models" on page 1-2 to determine which interfaces apply to
your imager.
In Wand Emulation mode, the imager decodes the barcode then sends data in
the same format as a wand imager. The Code 39 Format converts all
symbologies to Code 39.
Interleaved 2 of 5 without any changes, but converts all other symbologies to
Code 39. 2D symbologies are converted to Code 128.
4600rp, 4600g/4600r, 4800i User’s Guide
1 - 13
The Wand Emulation Plug & Play (Code 39 Format) barcode below sets the
terminal ID to 61. The Wand Emulation Plug & Play Same Code barcode sets
the terminal ID to 64. These barcodes also set the Transmission Rate to 25
inches per second, Output Polarity to black high, and Idle State to high. (If you
want to change the terminal ID only, without changing any other imager settings,
please refer to Wand Emulation Connection on page 2-13.)
Wand Emulation
Plug & Play
(Code 39 Format)
Wand Emulation
Plug & Play
Same Code
1 - 14
4600rp, 4600g/4600r, 4800i User’s Guide
Reading Techniques
The imager has a view finder that projects a bright red or green aiming beam that
corresponds to the imager’s horizontal field of view. The aiming beam should be
centered over the barcode, but it can be positioned in any direction for a good
read.
Linear barcode
2D Matrix symbol
The aiming beam is smaller when the imager is closer to the code and larger
when it is farther from the code. Symbologies with smaller bars or elements (mil
size) should be read closer to the unit. Symbologies with larger bars or elements
(mil size) should be read farther from the unit. To read single or multiple symbols
(on a page or on an object), hold the imager at an appropriate distance from the
target, pull the trigger, and center the aiming beam on the symbol. If the code
being scanned is highly reflective (e.g., laminated), it may be necessary to tilt the
code +5° to prevent unwanted reflection.
4600rp, 4600g/4600r, 4800i User’s Guide
1 - 15
1 - 16
4600rp, 4600g/4600r, 4800i User’s Guide
2
Terminal Interfaces
Terminal ID
If your interface is not covered by a Plug and Play barcode from Chapter 1, then
refer to Supported Terminals on page 2-2 through page 2-3, and locate the
Terminal ID number for your PC. Scan the Terminal ID barcode below, then
scan the numeric barcode(s) from the Programming Chart inside the back cover
of this manual to program the imager for your terminal ID. Scan Save to save
your selection.
For example, an IBM AT terminal has a Terminal ID of 003. You would scan the
Terminal ID barcode, then 0, 0, 3 from the Programming Chart inside the back
cover of this manual, then Save. If you make an error while scanning the digits
(before scanning Save), scan the Discard code on the Programming Chart, scan
the Terminal ID barcode, scan the digits, and the Save code again.
Terminal ID
Save
Note: After scanning one of these codes, you must power cycle your computer.
4600rp, 4600g/4600r, 4800i User’s Guide
2 - 1
Supported Terminals
Note: See "Imager Models" on page 1-2 to determine which interfaces apply to
your imager.
Terminal
Terminal
Model(s)
ID
DDC
DDC
DEC
DEC
3496, 3497, 122 key
3496, 3497, 102 key
VT510, 520, 525 (PC style)
VT510, 520, 525 (DEC style
LK411)
005
071
084
104
Esprit
Heath Zenith
Heath Zenith
HP
HP
IBM
200, 400
PC, AT
005
003
090
003
023
001
002
003 *
Vectra
Vectra
XT
IBM
IBM
PS/2 25, 30, 77DX2
AT, PS/2 30–286, 50, 55SX,
60, 70, 70–061, 70–121, 80
IBM 102 key
3151, 3161, 3162, 3163, 3191,
3192, 3194, 3196, 3197, 3471,
3472, 3476, 3477
006
IBM 122 key
IBM 122 key
3191, 3192, 3471, 3472
3196, 3197, 3476, 3477, 3486,
3482, 3488
007
008
IBM 122 key
IBM 122 key
IBM DOS/V 106 key
IBM SurePOS
IBM SurePOS
IBM Thinkpad
IBM Thinkpad
IBM Thinkpad
I/O 122 key
ITT
3180
024
114
102
128*
129*
097
106
003
008
007
007
103
001
003
3180 data entry keyboard
PC & Workstation
USB Hand Held Imager
USB Tabletop Imager
360 CSE, 340, 750
365, 755CV
2676D, 2677C, 2677D
9271
Lee Data
NEC
Olivetti
Olivetti
IIS
98XX Series
M19, M200
M240, M250, M290, M380,
P500
RS-232 True
RS-232 TTL
000**
000
2 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
Supported Terminals
Note: See "Imager Models" on page 1-2 to determine which interfaces apply to
your imager.
Terminal
Terminal
Model(s)
ID
Serial Wedge
Silicon Graphics
Telex 88 key
050
005
025
Indy, Indigoll
078, 078A, 79, 80, 191, 196,
1191,1192, 1471, 1472, 1476,
1477, 1483
Telex 88 key
Telex 102 key
Data Entry Keyboard
112
045
078, 078A, 79, 80, 191, 196,
1191,1192, 1471, 1472, 1476,
1477, 1483
Telex 122 key
078, 078A, 79, 80, 191, 196,
1191,1192, 1471, 1472, 1476,
1477, 1482, 1483
046
USB COM Port Emulation
USB PC Keyboard
USB Mac Keyboard
USB HID POS
Wand Emulation (Code 39
Format)
130
124*
125*
131*
061
Wand Emulation (Same
Code Format)
064
* Default for 4600g/4600r/4600rp/4800iXX 05XX models. It is best to use the Plug and
Play barcodes, beginning on page 1-9, to program these interfaces, rather than scan-
ning the terminal ID listed in this table.
** Default for 4600g/4800iXX 03XX models
4600rp, 4600g/4600r, 4800i User’s Guide
2 - 3
Keyboard Country
Scan the appropriate country code below to program the keyboard for your
country. As a general rule, the following characters are supported, but need
special care for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
* United States
Belgium
Brazil
Canada (French)
Czech Republic
Denmark
Finland (Sweden)
France
Germany/Austria
Greece
Hungary
Israel (Hebrew)
2 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
Keyboard Country (continued)
Turkey F
Turkey Q
U.K.
Please refer to the Hand Held Products website (www.handheld.com) for
complete keyboard country support information and applicable interfaces. If you
need to program a keyboard for a country other than one listed above, scan the
Program Keyboard Country barcode below, then scan the numeric barcode(s)
for the appropriate country from the inside back cover, then the Save barcode.
Program Keyboard Country
Keyboard Style
This programs keyboard styles, such as Caps Lock and Shift Lock. Default =
Regular.
Regular is used when you normally have the Caps Lock key off.
* Regular
Caps Lock is used when you normally have the Caps Lock key on.
Caps Lock
2 - 6
4600rp, 4600g/4600r, 4800i User’s Guide
Shift Lock is used when you normally have the Shift Lock key on (not common
to U.S. keyboards).
Shift Lock
Automatic Caps Lock is used if you change the Caps Lock key on and off. The
software tracks and reflects if you have Caps Lock on or off (AT and PS/2 only).
This selection can only be used with systems that have an LED which notes the
Caps Lock status.
Automatic Caps Lock
Autocaps via NumLock barcode should be scanned in countries (e.g.,
Germany, France) where the Caps Lock key cannot be used to toggle Caps
Lock. The NumLock option works similarly to the regular Auotcaps, but uses the
NumLock key to retrieve the current state of the Caps Lock.
Autocaps via NumLock
Emulate External Keyboard should be scanned if you do not have an external
keyboard (IBM AT or equivalent).
Emulate External Keyboard
Note: After scanning the Emulate External Keyboard barcode, you must power
cycle your computer.
Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo
Mode.
4600rp, 4600g/4600r, 4800i User’s Guide
2 - 7
Control + ASCII Mode On: The imager sends key combinations for ASCII
control characters for values 00-1F. Windows is the preferred mode. All
keyboard country codes are supported. DOS mode is a legacy mode, and it does
not support all keyboard country codes. New users should use the Windows
mode. Refer to Keyboard Function Relationships, page 10-1 for CTRL+ ASCII
Values. Default = Off
Windows Mode Control + ASCII
* Control + ASCII Mode Off
DOS Mode Control + ASCII Mode
Turbo Mode: The imager sends characters to a terminal faster. If the terminal
drops characters, do not use Turbo Mode. Default = Off
Turbo Mode On
* Turbo Mode Off
Numeric Keypad Mode: Sends numeric characters as if entered from a
numeric keypad. Default = Off
Numeric Keypad Mode On
* Numeric Keypad Mode Off
2 - 8
4600rp, 4600g/4600r, 4800i User’s Guide
RS-232 Word Length: Data Bits, Stop Bits, and Parity
Data Bits sets the word length at 7 or 8 bits of data per character. If an
application requires only ASCII Hex characters 0 through 7F decimal (text, digits,
and punctuation), select 7 data bits. For applications which require use of the full
ASCII set, select 8 data bits per character. Default = 8.
Stop Bits sets the stop bits at 1 or 2. Default = 1.
Parity provides a means of checking character bit patterns for validity.
Default = None.
7 Data, 1 Stop, Parity Even
7 Data, 1 Stop, Parity None
7 Data, 1 Stop, Parity Odd
7 Data, 2 Stop, Parity Even
7 Data, 2 Stop Parity None
7 Data, 2 Stop, Parity Odd
8 Data, 1 Stop, Parity Even
* 8 Data, 1 Stop, Parity None
8 Data, 1 Stop, Parity Odd
4600rp, 4600g/4600r, 4800i User’s Guide
2 - 11
RS-232 Receiver Time-Out
The unit stays awake to receive data until the RS-232 Receiver Time-Out
expires. A manual or serial trigger resets the time-out. When an RS-232
receiver is sleeping, a character may be sent to wake up the receiver and reset
the time-out. A transaction on the CTS line will also wake up the receiver. The
receiver takes 300 milliseconds to completely come up. Change the RS-232
receiver time-out by scanning the barcode below, then scanning digits from the
inside back cover of this manual, then scanning Save. The range is 0 to 300
seconds. Default = 0 seconds (no time-out - always on).
RS-232 Receiver Time-Out
RS-232 Handshaking
RS-232 Handshaking allows control of data transmission from the Imager using
software commands from the host device. When this feature is turned Off, no
data flow control is used. When Data Flow Control is turned On, the host device
suspends transmission by sending the XOFF character (DC3, hex 13) to the
Imager. To resume transmission, the host sends the XON character (DC1, hex
11). Data transmission continues where it left off when XOFF was sent. Default
= RTS/CTS, XON/XOFF and ACK/NAK Off.
RTS/CTS On
* RTS/CTS Off
XON/XOFF On
* XON/OFF Off
ACK/NAK On
* ACK/NAK Off
2 - 12
4600rp, 4600g/4600r, 4800i User’s Guide
Wand Emulation Connection
The Wand Emulation Connection barcodes should be used if you want to change
the terminal ID only, without changing any other imager settings. We
recommend using Wand Emulation Plug & Play barcodes to program your
imager to emulate a wand reader. The Wand Emulation Plug & Play barcodes
change other parameters, in addition to changing the terminal ID. Please refer
to Connecting the Imager with RS-232 Wedge on page 1-7 for further
information.
In Wand Emulation mode, the imager decodes the barcode then sends data in
the same format as a wand imager. The Code 39 Format converts all
symbologies to Code 39.
The Same Code Format transmits UPC, EAN, Code 128, Codabar, and
Interleaved 2 of 5 without any changes, but converts all other symbologies to
Code 39. 2D symbologies are converted to Code 128.
The Code 39 Format barcode below sets the terminal ID to 61, and the Same
Code Format barcode sets the terminal ID to 64. Default = Code 39 Format.
Code 39 Format
Same Code Format
4600rp, 4600g/4600r, 4800i User’s Guide
2 - 13
Wand Emulation
Note: See "Imager Models" on page 1-2 to determine which interfaces apply to
your imager.
Note: Changing primary wand emulation settings also changes the secondary
wand emulation settings (see Secondary Code 39 Wand Emulation on
page 6-2).
Data Block Size
This transmits the data in smaller blocks to prevent buffer overflow. Default = 40.
20
* 40
60
80
Delay Between Blocks
This sets the delay time between data blocks. Default = 50ms.
5ms
* 50ms
150ms
500ms
2 - 14
4600rp, 4600g/4600r, 4800i User’s Guide
Overall Checksum
When this option is turned on, a computed check character is added at the end
of the entire message. The check character is the character which when
Exclusive-OR’d with every preceding character of the message yields a result of
0x00 (00H). Default = Off.
On
* Off
Wand Emulation Transmission Rate
The Transmission Rate is limited by the terminal’s ability to receive data without
dropping characters. Default = 25 inches/second.
10
* 25
40
80
120
150
200
4600rp, 4600g/4600r, 4800i User’s Guide
2 - 15
Wand Emulation Polarity
The Polarity can be sent as standard with black bars high, or reversed with white
bars high. Default = Black High.
* Black High
White High
Wand Emulation Idle
The idle describes the state of the imager when no data is being transmitted.
When in Wand Emulation mode, you must set the imager’s idle state to match
the idle state for the device to which the imager is connected. Default = Idle High.
* Idle High
Idle Low
2 - 16
4600rp, 4600g/4600r, 4800i User’s Guide
3
Output
Good Read Indicators
Beeper – Good Read
The beeper may be programmed On or Off in response to a good read. Turning
this option off, only turns off the beeper response to a good read indication. All
error and menu beeps are still audible. Default = On.
* On
Off
Beeper Volume – Good Read
The beeper volume codes modify the volume of the beep the imager emits on a
good read. Default = Medium for the 4600g/4600r/4600rp; High for the 4800i.
Low
Medium
High
Off
4600rp, 4600g/4600r, 4800i User’s Guide
3 - 1
Beeper Pitch – Good Read
The beeper pitch codes modify the pitch (frequency) of the beep the imager emits
on a good read. Default = Medium.
Low (1600 Hz)
* Medium (3250 Hz)
High (4200 Hz)
Beeper Duration – Good Read
The beeper duration codes modify the length of the beep the imager emits on a
good read. Default = Normal.
* Normal Beep
Short Beep
LED – Good Read
The LED indicator can be programmed On or Off in response to a good read.
Default = On.
* On
3 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
Number of Beeps – Good Read
The number of beeps of a good read can be programmed from 1 - 9. The same
number of beeps will be applied to the beeper and LED in response to a good
read. For example, if you program this option to have five beeps, there will be
five beeps and five LED flashes in response to a good read. The beeps and LED
flashes are in sync with one another. To change the number of beeps, scan the
barcodebarcode below and then scan a digit (1-9) barcode and the Save
barcode on the Programming Chart inside the back cover of this manual. Default
= One.
Number of Pulses
Good Read Delay
This sets the minimum amount of time before the imager can read another
barcode. Default = No Delay.
* No Delay
Short Delay (500 ms)
Medium Delay (1,000 ms)
Long Delay (1,500 ms)
User-Specified Good Read Delay
If you want to set your own length for the good read delay, scan the barcode
below, then set the delay (from 0-30,000 milliseconds) by scanning digits from
the inside back cover, then scanning Save.
User-Specified Good Read Delay
4600rp, 4600g/4600r, 4800i User’s Guide
3 - 3
Trigger Modes
Manual/Serial Trigger
You can activate the imager either by pressing the trigger, or using a serial trigger
command (see Trigger Commands on page 12-4). When in manual trigger
mode, the imager scans until a barcode is read, or until the trigger is released.
When in serial mode, the imager scans until a barcode has been read or until the
deactivate command is sent. In serial mode, the imager can also be set to turn
itself off after a specified time has elapsed (see Read Time-Out, which follows).
* Manual/Serial Trigger
Read Time-Out
Use this selection to set a time-out (in milliseconds) of the imager’s trigger when
using serial commands to trigger the imager, or if the imager is in manual trigger
mode. Once the imager has timed out, you can activate the imager either by
pressing the trigger or using a serial trigger command. After scanning the Read
Time-Out barcode, set the time-out duration (from 0-300,000 milliseconds) by
scanning digits from the inside back cover, then scanning Save. Default =
30,000.
Read Time-Out
Manual Trigger, Low Power
Note: Does not apply to the 4600r.
The imager powers down until the trigger is pulled. When the trigger is pulled,
the imager powers up and operates until there is no triggering for the time set
with the Low Power Time-Out barcode below. There is a delay of up to one
second in operation when the imager is first triggered, but there is no delay when
operating in low power time-out mode.
Manual Trigger, Low Power
3 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
Note: Manual Trigger, Low Power cannot be used with keyboard wedge
applications.
Low Power Time-Out Timer
Scan the Low Power Time-Out barcode to change the time-out duration (in
seconds). Then scan the time-out duration (from 0-300 seconds) from the inside
back cover, and Save. Default = 120 seconds.
If the unit remains idle during the low power time-out interval, the unit goes into
low power mode. Whenever the trigger is enabled, the low power time-out timer
is reset.
Note: This time-out does not begin until the imager time-out setting has expired.
In-Stand Sensor Mode (4600r only)
The 4600r (Software revision 31205480-118 or newer) contains a sensor that
senses when the imager is removed from the stand (HFSTAND5RSE only).
Refer to the Show Software Revision on page 11-2 for information on
determining the software in your unit. The imager then enters Manual Trigger
mode. If you wish to turn the sensor on, scan the Sensor ON barcode below.
Default = Off.
Sensor On
* Sensor Off
Scan Stand Mode
Note: Scan Stand Mode is only available for non-advanced illumination units
with software revision 31205480-090 or older. Refer to the Show
Software Revision on page 11-2 for information on determining the
software in your unit.
When a unit is in Scan Stand mode, it remains idle as long as it sees the Scan
Stand symbol. (See Scan Stand Symbol on page 3-6.) When a different code is
presented, the imager is triggered to read the new code.
4600rp, 4600g/4600r, 4800i User’s Guide
3 - 5
Note: The imager automatically adjusts the illumination LEDs to the lowest light
level possible to maintain a good lock on the Scan Stand symbol. When
a symbol is presented, the imager’s light levels adjust to the saved setting
(see LED Power Level on page 3-9). This mode requires at least 50 lux
of ambient light to operate correctly.
Scan Stand Mode
Scan Stand Symbol
When a unit is in Scan Stand mode, the LEDs shine at the Scan Stand symbol
on the base of the stand which tells it to remain idle. When the Scan Stand
symbol is covered, the imager turns the LEDs on at the configured power level
(Default High) and attempts to find and decode barcodes in its field of view.
Scan Stand Symbol
Presentation Mode
Note: The operation of light bar off-axis illumination units and non-light bar units
differs slightly. When a light bar unit is in Presentation Mode and idle, the
illumination LEDs go dim, but never go out. When a non-light bar unit is in
Presentation Mode and idle, the illumination LEDs will go out completely.
This programs the imager to work in Presentation mode. The LEDs are either off
or at the lowest power for ambient conditions until a barcode is presented to the
imager. Then the LEDs turn on automatically to read the code. Presentation
Mode uses ambient light to detect the barcodes. If the light level in the room is
not high enough, Presentation Mode may not work properly.
Presentation Mode
3 - 6
4600rp, 4600g/4600r, 4800i User’s Guide
Presentation LED Behavior after Decode
When an imager is in presentation mode, the LEDs remain on and continue
scanning for a short time after a barcode is decoded. If you wish to turn the LEDs
off immediately after a barcode is decoded, scan the LEDs Off barcode, below.
Default = LEDs On.
* LEDs On
LEDs Off
Presentation Sensitivity
Presentation Sensitivity is a numeric range that increases or decreases the
imager's reaction time to barcode presentation. To set the sensitivity, scan the
Sensitivity barcode, then scan the degree of sensitivity (from 0-20) from the
inside back cover, and Save. 0 is the most sensitive setting, and 20 is the least
sensitive. Default = 1.
Sensitivity
Streaming Presentation™ Mode
Note: Streaming Presentation Mode applies only to units with advanced
illumination. Units with advanced illumination have a software revision of
31205480-118 or newer. Refer to the Show Software Revision on page
11-2 for information on determining the software in your unit.
When in Streaming Presentation mode, the imager leaves the scan illumination
on all the time and continuously searches for barcodes.
Streaming Presentation Mode
When using Preferred Symbology (page 3-14), a lower priority symbol must be
centered on the aiming pattern to be read in Streaming Presentation Mode.
4600rp, 4600g/4600r, 4800i User’s Guide
3 - 7
Hands Free Time-Out
The Scan Stand, and Presentation, and Streaming Presentation Modes are
referred to as “hands free” modes. If the imager’s trigger is pulled when using a
hands free mode, the imager changes to manual trigger mode. You can set the
time the imager should remain in manual trigger mode by setting the Hands Free
Time-Out. Once the time-out value is reached, (if there have been no further
trigger pulls) the imager reverts to the original hands free mode.
Scan the Hands Free Time-Out barcode, then scan the time-out duration (from
0-300,000 milliseconds) from the inside back cover, and Save. Default = 5,000
ms.
Hands Free Time-Out
Reread Delay
This sets the time period before the imager can read the same barcode a second
time. Setting a reread delay protects against accidental rereads of the same
barcode. Longer delays are effective in minimizing accidental rereads. Use
shorter delays in applications where repetitive barcode scanning is required.
Default = Medium.
Reread Delay only works when in Presentation Mode or Streaming
Presentation™ Mode (page 3-7).
Short (500 ms)
* Medium (750 ms)
Long (1000 ms)
Extra Long (2000 ms)
3 - 8
4600rp, 4600g/4600r, 4800i User’s Guide
User-Specified Reread Delay
If you want to set your own length for the reread delay, scan the barcode below,
then set the delay (from 0-30,000 milliseconds) by scanning digits from the inside
back cover, then scanning Save.
User-Specified Reread Delay
LED Power Level
This selection allows you to adjust LED and aimer brightness. Off is used when
no illumination is needed. Low is used if low illumination is sufficient. High (the
default) is the brightest setting.
If you have an aimer delay programmed (see Aimer Delay on page 3-10), the
aimer will be at 100% power during the delay, regardless of the LED Power
Level.
Note: If you scan the Off barcode, both the aimer and illumination lights turn off,
making it impossible to scan barcodes in low light. To turn the LED Power
Level back on, move to a brightly lit area and scan either the Low or the
High barcode below.
Off
Low (50%)
* High (100%)
Illumination Lights
If you want the illumination lights on while reading a barcode, scan the Lights On
Off barcode.
4600rp, 4600g/4600r, 4800i User’s Guide
3 - 9
Note: This setting does not affect the aimer light. The aiming light can be set
using Aimer Mode (page 3-11).
* Lights On
Lights Off
Imager Time-Out
Imager Time-Out powers down the imager after the unit has been idle for the
specified time. To prevent the imager from powering down, set this time-out to
0. Scan the barcode below, then set the time-out by scanning digits (from 0 -
999,999 ms) from the inside back cover, then scanning Save. Default = 60,000
ms.
Note: The default applies to firmware with a base number of 31205480. Refer
to the Show Software Revision on page 11-2 for information on
determining the firmware revision in your unit.
Imager Time-Out
Aimer Delay
The aimer delay allows a delay time for the operator to aim the imager before the
picture is taken. Use these codes to set the time between when the trigger is
pulled and when the picture is taken. During the delay time, the aiming light will
appear, but the LEDs won’t turn on until the delay time is over.
200 milliseconds
400 milliseconds
* Off (no delay)
3 - 10
4600rp, 4600g/4600r, 4800i User’s Guide
User-Specified Aimer Delay
If you want to set your own length for the duration of the delay, scan the barcode
below, then set the time-out by scanning digits (0 - 4,000 ms) from the
Programming Chart inside the back cover of this manual, then scan Save.
Delay Duration
Aimer Mode
Note: Concurrent is the default for units with 4X00 engines. Interlaced is the
default for units with 5X00 engines. Refer to the Show Engine
Revision on page 11-1 for information on determining the engine in your
unit. The 4600g, 4600r, 4800i, and 4600rp do not allow concurrent aimer
mode.
The Aimer Mode feature allows you to lower peak current during scanning by
alternating the aimer and illumination LEDs. When the Interlaced barcode is
scanned, the aimer and illumination LEDs are not allowed to be on at the same
time. Interlaced, the recommended setting for the 5X00 engines, limits the peak
current draw during scanning. For 4X00 engines, the Interlaced setting reduces
the frame capture rate. When the Concurrent barcode is scanned, the aimer and
illumination LEDs are allowed to light at the same time. This is the recommended
setting for the 4X00 engines. Select Off for fixed mount applications when the
aimer is not needed.
Off
Concurrent
Interlaced
4600rp, 4600g/4600r, 4800i User’s Guide
3 - 11
Centering
Use Centering to narrow the imager’s field of view to make sure the imager reads
only those barcodes intended by the user. For instance, if multiple codes are
placed closely together, centering will insure that only the desired codes are
read. (Centering can be used in conjunction with Aimer Delay, page 3-10, for
the most error-free operation in applications where multiple codes are spaced
closely together. Using the Aimer Delay and Centering features, the imager can
emulate the operation of older systems, such as linear laser barcode imagers.)
In the example below, the gray area is the full imager field of view and the white
area is the centering window. Barcode 1 will not be read, while Barcode 2 will
be.
Barcode 1
Barcode 2
The default centering window is a 128x96 pixel area in the center of the imager’s
field of view. The following diagram illustrates the default top, bottom, left, and
right pixel positions, measured from the top and the left side of the imager’s field
of view, which is 640 by 480 pixels.
40%
60%
100%
0
Top
40%
60%
Bottom
Default
Center
Left
Right
100%
If a barcode is not within the predefined window, it will not be decoded or output
by the imager. If centering is turned on by scanning Centering On, the imager
only reads codes that intersect the centering window you specify using the Top,
Bottom, Left, or Right barcodes.
3 - 12
4600rp, 4600g/4600r, 4800i User’s Guide
Scan Centering On, then scan one of the following barcodes to change the top,
bottom, left, or right of the centering window. Then scan the percent you want to
shift the centering window using digits on the inside back cover of this manual.
Scan Save. Default Centering = 40% for Top and Left, 60% for Bottom and
Right.
Centering On
* Centering Off
Top of Centering Window
Bottom of Centering Window
Left of Centering Window
Right of Centering Window
4600rp, 4600g/4600r, 4800i User’s Guide
3 - 13
Decode Search Mode
There are three selectable decode (scanning) modes:
Full Omnidirectional - Searches for barcode features beginning at the center of
an image, and searches to the image’s limits. This mode reads all symbologies
(including OCR), in any orientation. The Full Omnidirectional search is very
thorough which may slow performance time.
Note: This search mode is the default setting.
Full Omnidirectional
Quick Omnidirectional - This is an abbreviated search for barcode features
around the center region of an image. This mode quickly reads all symbologies
in any orientation. The Quick Omnidirectional mode may miss some off-center
symbols, as well as larger Data Matrix and QR Code symbols.
Quick Omnidirectional
Advanced Linear Decoding - Performs quick horizontal linear scans in a center
band of the image. This mode is not omnidirectional, but does quickly read linear
and stacked barcodes. Advanced Linear Decoding cannot read 2D, OCR, or
Postal symbols.
Advanced Linear Decoding
Preferred Symbology
Note: This selection does not apply to OCR.
The imager can be programmed to specify one symbology as a higher priority
over other symbologies in situations where both barcode symbologies appear on
the same label, but the lower priority symbology cannot be disabled.
For example, you may be using the imager in a retail setting to read UPC
symbols, but have occasional need to read a code on a drivers license. Since
some licenses have a Code 39 symbol as well as the PDF417 symbol, you can
use Preferred Symbology to specify that the PDF417 symbol be read instead of
the Code 39.
3 - 14
4600rp, 4600g/4600r, 4800i User’s Guide
Preferred Symbology classifies each symbology as high priority, low priority,
or as an unspecified type. When a low priority symbology is presented, the
imager ignores it for a set period of time (see Preferred Symbology Time-out on
page 3-16) while it searches for the high priority symbology. If a high priority
symbology is located during this period, then that data is read immediately.
If the time-out period expires before a high priority symbology is read, the imager
will read any barcode in its view (low priority or unspecified). If there is no
barcode in the imager’s view after the time-out period expires, then no data is
reported.
Note: A low priority symbol must be centered on the aiming pattern to be read.
Scan a barcode below to enable or disable Preferred Symbology.
Preferred Symbology On
* Preferred Symbology Off
High Priority Symbology
To specify the high priority symbology, scan the High Priority Symbology
barcode below. On the Symbology Chart on page A-1, find the symbology you
want to set as high priority. Locate the Hex value for that symbology and scan
the 2 digit hex value from the Programming Chart (inside back cover). Scan
High Priority Symbology
Low Priority Symbology
To specify the low priority symbology, scan the Low Priority Symbology barcode
below. On the Symbology Chart on page A-1, find the symbology you want to
set as low priority. Locate the Hex value for that symbology and scan the 2 digit
hex value from the Programming Chart (inside back cover).
If you want to set additional low priority symbologies, scan FF, then scan the 2
digit hex value from the Programming Chart for the next symbology. You can
program up to 5 low priority symbologies. Scan Save to save your selection.
Default = None
Low Priority Symbology
4600rp, 4600g/4600r, 4800i User’s Guide
3 - 15
Preferred Symbology Time-out
Once you have enabled Preferred Symbology and entered the high and low
priority symbologies, you must set the time-out period. This is the period of time
the imager will search for a high priority barcode after a low priority barcode has
been encountered. Scan the barcode below, then set the delay (from 100-3,000
milliseconds) by scanning digits from the inside back cover, then scanning Save.
Default = 500 ms.
Preferred Symbology Time-out
Preferred Symbology Default
Scan the barcode below to set all Preferred Symbology entries to their default
values.
Preferred Symbology Default
Output Sequence Overview
Require Output Sequence
When turned off, the barcode data will be output to the host as the Imager
decodes it. When turned on, all output data must conform to an edited sequence
or the imager will not transmit the output data to the host device.
Note: This selection is unavailable when Multiple Symbols (page 3-20) is
enabled.
Output Sequence Editor
This programming selection allows you to program the imager to output data
(when scanning more than one symbol) in whatever order your application
requires, regardless of the order in which the barcodes are scanned. Reading
the Default Sequence symbol programs the imager to the Universal values,
Note: To make Output Sequence Editor selections, you’ll need to know the code
I.D., code length, and character match(es) your application requires. Use
the Alphanumeric symbols (inside back cover) to read these options.
You must hold the trigger while reading each barcode in the sequence.
To Add an Output Sequence
1. Scan the Enter Sequence symbol (see Require Output Sequence, page 3-
19).
3 - 16
4600rp, 4600g/4600r, 4800i User’s Guide
2. Code I.D.
On the Symbology Chart on page A-1, find the symbology to which you want
to apply the output sequence format. Locate the Hex value for that symbol-
ogy and scan the 2 digit hex value from the Programming Chart (inside back
cover).
3. Length
Specify what length (up to 9999 characters) of data output will be acceptable
for this symbology. Scan the four digit data length from the Programming
Chart. (Note: 50 characters is entered as 0050. 9999 is a universal num-
ber, indicating all lengths.) When calculating the length, you must count any
programmed prefixes, suffixes, or formatted characters as part of the length
(unless using 9999).
4. Character Match Sequences
On the ASCII Conversion Chart (Code Page 1252), page A-4, find the Hex
value that represents the character(s) you want to match. Use the Program-
ming Chart to read the alphanumeric combination that represents the ASCII
characters. (99 is the Universal number, indicating all characters.)
5. End Output Sequence Editor
Scan F F to enter an Output Sequence for an additional symbology, or Save
to save your entries.
Other Programming Selections
•Discard
This exits without saving any Output Sequence changes.
Output Sequence Examples
In this example, you are scanning Code 93, Code 128, and Code 39 barcodes,
but you want the imager to output Code 39 1st, Code 128 2nd, and Code 93 3rd,
as shown below.
Note: Code 93 must be enabled to use this example.
A - Code 39
B - Code 128
C - Code 93
4600rp, 4600g/4600r, 4800i User’s Guide
3 - 17
You would set up the sequence editor with the following command line:
SEQBLK62999941FF6A999942FF69999943FF
The breakdown of the command line is shown below:
SEQBLK sequence editor start command
62
code identifier for Code 39
9999
41
FF
code length that must match for Code 39, 9999 = all lengths
start character match for Code 39, 41h = “A”
termination string for first code
6A
code identifier for Code 128
9999
42
FF
code length that must match for Code 128, 9999 = all lengths
start character match for Code 128, 42h = “B”
termination string for second code
69
code identifier for Code 93
9999
43
FF
code length that must match for Code 93, 9999 = all lengths
start character match for Code 93, 43h = “C”
termination string for third code
To program the previous example using specific lengths, you would have to
count any programmed prefixes, suffixes, or formatted characters as part of the
length. If you use the example on page 3-17, but assume a <CR> suffix and
specific code lengths, you would use the following command line:
SEQBLK62001241FF6A001342FF69001243FF
The breakdown of the command line is shown below:
SEQBLK sequence editor start command
62
code identifier for Code 39
0012
41
FF
A - Code 39 sample length (11) plus CR suffix (1) = 12
start character match for Code 39, 41h = “A”
termination string for first code
6A
code identifier for Code 128
0013
42
FF
B - Code 128 sample length (12) plus CR suffix (1) = 13
start character match for Code 128, 42h = “B”
termination string for second code
69
code identifier for Code 93
0012
43
FF
C - Code 93 sample length (11) plus CR suffix (1) = 12
start character match for Code 93, 43h = “C”
termination string for third code
3 - 18
4600rp, 4600g/4600r, 4800i User’s Guide
Output Sequence Editor
Enter Sequence
Default Sequence
Require Output Sequence
When an output sequence is Required, all output data must conform to an edited
sequence or the imager will not transmit the output data to the host device.
When it’s On/Not Required, the imager will attempt to get the output data to
conform to an edited sequence, but if it cannot, the imager transmits all output
data to the host device as is.
When the output sequence is Off, the barcode data is output to the host as the
imager decodes it.
Note: This selection is unavailable when the Multiple Symbols Selection is
turned on.
Required
On/Not Required
*Off
4600rp, 4600g/4600r, 4800i User’s Guide
3 - 19
Multiple Symbols
Note: This feature does not work when the Imager is in Low Power mode.
When this programming selection is turned On, it allows you to read multiple
symbols with a single pull of the Imager’s trigger. If you press and hold the
trigger, aiming the Imager at a series of symbols, it reads unique symbols once,
beeping (if turned on) for each read. The imager attempts to find and decode
new symbols as long as the trigger is pulled. When this programming selection
is turned Off, the Imager will only read the symbol closest to the aiming beam.
On
* Off
No Read
With No Read turned On, the Imager notifies you if a code cannot be read. If
using a Quick*View Scan Data Window, an “NR” appears when a code cannot
be read. If No Read is turned Off, the “NR” will not appear.
On
* Off
If you want a different notation than “NR,” for example, “Error,” or “Bad Code,”
you can edit the output message using the Data Formatter (page 5-5). The hex
code for the No Read symbol is 9C.
3 - 20
4600rp, 4600g/4600r, 4800i User’s Guide
Print Weight
Print Weight is used to adjust the way the imager reads Matrix symbols. If an
imager will be seeing consistently heavily printed matrix symbols, then a print
weight of 6 may improve the reading performance. For consistently light printing,
a print weight of 2 may help. After scanning the Set Print Weight barcode, set
the print weight (from 1-7) by scanning digits from the inside back cover, then
scanning Save. Default = 4.
Set Print Weight
* Default
Video Reverse
Video Reverse is used to allow the imager to read barcodes that are inverted.
The “Off” barcode below is an example of this type of barcode. If additional
menuing is required, Video Reverse must be disabled to read the menu barcodes
and then re-enabled after menuing is completed.
Note: Images downloaded from the unit will not be reversed. This is a setting for
decoding only.
On
* Off
4600rp, 4600g/4600r, 4800i User’s Guide
3 - 21
Working Orientation
Some barcodes are direction-sensitive. For example, KIX codes and OCR can
misread when scanned sideways or upside down. Use the working orientation
settings if your direction-sensitive codes will not usually be presented upright to
the imager. Default = Upright.
Upright:
Rotate Code Clockwise 90°:
Upside Down:
Rotate Code
Counterclockwise 90°:
* Upright
Rotate Code Clockwise 90°
(Rotate Imager
Counterclockwise)
Upside Down
Rotate Code
Counterclockwise 90°
3 - 22
4600rp, 4600g/4600r, 4800i User’s Guide
4
Data Editing
Prefix/Suffix Overview
When a barcode is scanned, additional information is sent to the host computer
along with the barcode data. This group of barcode data and additional,
user-defined data is called a “message string.” The selections in this section are
used to build the user-defined data into the message string.
Prefix and Suffix characters are data characters that can be sent before and after
scanned data. You can specify if they should be sent with all symbologies, or
only with specific symbologies. The following illustration shows the breakdown
of a message string:
Prefix
1-11
alpha numeric
characters
Scanned Data
Suffix
1-11
alpha numeric
characters
variable length
Points to Keep In Mind
•
It is not necessary to build a message string. The selections in this chapter
are only used if you wish to alter the default settings. Default prefix = None.
Default suffix = None.
•
•
A prefix or suffix may be added or cleared from one symbology or all
symbologies.
You can add any prefix or suffix from the ASCII Conversion Chart (Code Page
1252), page A-4, plus Code I.D. and AIM I.D.
•
•
You can string together several entries for several symbologies at one time.
Enter prefixes and suffixes in the order in which you want them to appear on
the output.
•
When setting up for specific symbologies, instead of All Symbologies, the
symbology ID value counts as an added prefix or suffix character.
4600rp, 4600g/4600r, 4800i User’s Guide
4 - 1
To Add a Prefix or Suffix:
Appendix A) for the symbology to which you want to apply the prefix or
suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”.
Step 3. Scan the 2 hex digits from the Programming Chart inside the back
cover of this manual or scan 9, 9 for all symbologies.
Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page
1252), page A-4, for the prefix or suffix you wish to enter.
Step 5. Scan the 2 digit hex value from the Programming Chart inside the back
cover of this manual.
Step 6. Repeat Steps 4 and 5 for every prefix or suffix character.
Step 7. To add the Code I.D., scan 5, C, 8, 0.
To add AIM I.D., scan 5, C, 8, 1.
To add a backslash (\), scan 5, C, 5, C.
Note: To add a backslash (\) as in Step 7, you must scan 5C twice – once to
create the leading backslash and then to create the backslash itself.
Repeat Steps 1-6 to add a prefix or suffix for another symbology.
Example: Add a Suffix to a specific symbology
To send a CR (carriage return)Suffix for UPC only:
Step 1. Scan Add Suffix.
Step 2. Determine the 2 digit hex value from the Symbology Chart (included in
Appendix A) for UPC.
Step 3. Scan 6, 3 from the Programming Chart inside the back cover of this
manual.
Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page
1252), page A-4, for the CR (carriage return).
Step 5. Scan 0, D from the Programming Chart inside the back cover of this
manual.
Step 6. Scan Save, or scan Discard to exit without saving.
4 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
You can clear a single prefix or suffix, or clear all prefixes/suffixes for a
select is deleted from the symbology you want. When you Clear All Prefixes
(Suffixes), all the prefixes or suffixes for a symbology are deleted.
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol.
Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in
Appendix A) for the symbology from which you want to clear the prefix
or suffix.
Step 3. Scan the 2 digit hex value from the Programming Chart inside the back
cover of this manual or scan 9, 9 for all symbologies.
Your change is automatically saved.
To Add a Carriage Return Suffix to all Symbologies
Scan the following barcode if you wish to add a carriage return suffix to all
symbologies at once. This action first clears all current suffixes, then programs
a carriage return suffix for all symbologies.
Add CR Suffix
All Symbologies
4600rp, 4600g/4600r, 4800i User’s Guide
4 - 3
Prefix Selections
Add Prefix
Clear One Prefix
Clear All Prefixes
Suffix Selections
Add Suffix
Clear One Suffix
Clear All Suffixes
Function Code Transmit
When this selection is enabled and function codes are contained within the
scanned data, the imager transmits the function code to the terminal. Charts of
these function codes are provided in Supported Interface Keys starting on
page 10-3. When the imager is in keyboard wedge mode, the scan code is
converted to a key code before it is transmitted. Default = Enable.
* Enable
Disable
4 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
Intercharacter, Interfunction, and Intermessage Delays
Some terminals drop information (characters) if data comes through too quickly.
Intercharacter, interfunction, and intermessage delays slow the transmission of
data, increasing data integrity.
Each delay is composed of a 5 millisecond step. You can program up to 99 steps
(of 5 ms each) for a range of 0-495 ms.
Intercharacter Delay
An intercharacter delay of up to 495 milliseconds (in 5 ms steps) may be placed
between the transmission of each character of scanned data. Scan the
Intercharacter Delay barcode below, then scan the number of 5 millisecond
steps (0-99), and the Save barcode using the Programming Chart inside the
back cover of this manual.
Prefix
Scanned Data
Suffix
1
2
3
4
5
Intercharacter Delay
Intercharacter Delay
To remove this delay, scan the Intercharacter Delay barcode, then set the
number of steps to 0. Scan the Save barcode using the Programming Chart
inside the back cover of this manual.
Note: Intercharacter delays are not supported in USB serial emulation.
4600rp, 4600g/4600r, 4800i User’s Guide
4 - 5
An intercharacter delay of up to 495 milliseconds (in 5 ms steps) may be placed
after the transmission of a particular character of scanned data. Scan the Delay
Length barcode below, then scan the number of 5 millisecond steps (0-99), and
the Save barcode using the Programming Chart inside the back cover of this
manual.
Next, scan the Character to Trigger Delay barcode, then the 2-digit hex value
for the ASCII character that will trigger the delay ASCII Conversion Chart (Code
Page 1252), page A-4.
Delay Length
Character to Trigger Delay
steps to 0. Scan the Save barcode using the Programming Chart inside the back
cover of this manual.
Interfunction Delay
An interfunction delay of up to 495 milliseconds (in 5 ms steps) may be placed
between the transmission of each segment of the message string. Scan the
Interfunction Delay barcode below, then scan the number of 5 millisecond steps
(0-99), and the Save barcode using the Programming Chart inside the back
cover of this manual.
Prefix
STX
Scanned Data
3 4
Suffix
CR
1
HT
2
5
LF
Interfunction Delays
Interfunction Delay
number of steps to 0. Scan the Save barcode using the Programming Chart
inside the back cover of this manual.
4 - 6
4600rp, 4600g/4600r, 4800i User’s Guide
Intermessage Delay
An intermessage delay of up to 495 milliseconds (in 5 ms steps) may be placed
between each scan transmission. Scan the Intermessage Delay barcode
below, then scan the number of 5 millisecond steps (0-99), and the Save barcode
using the Programming Chart inside the back cover of this manual.
1st Scan Transmission 2nd Scan Transmission
Intermessage Delay
Intermessage Delay
To remove this delay, scan the Intermessage Delay barcode, then set the
number of steps to 0. Scan the Save barcode using the Programming Chart
inside the back cover of this manual.
4600rp, 4600g/4600r, 4800i User’s Guide
4 - 7
4 - 8
4600rp, 4600g/4600r, 4800i User’s Guide
5
Data Formatting
You may use the Data Format Editor to change the imager’s output. For
example, you can use the Data Format Editor to insert characters at certain
points in barcode data as it is scanned. The selections in the following pages are
used only if you wish to alter the output. Default Data Format setting = None.
Normally, when you scan a barcode, it gets outputted automatically; however
when you do a format, you must use a “send” command (see Send Commands
on page 5-2) within the format program to output data.
Multiple formats may be programmed into the imager. They are stacked in the
order in which they are entered. However, the following list presents the order
in which formats are applied:
1. Specific Term ID, Actual Code ID, Actual Length
2. Specific Term ID, Actual Code ID, Universal Length
3. Specific Term ID, Universal Code ID, Actual Length
4. Specific Term ID, Universal Code ID, Universal Length
5. Universal Term ID, Actual Code ID, Actual Length
6. Universal Term ID, Actual Code ID, Universal Length
7. Universal Term ID, Universal Code ID, Actual Length
8. Universal Term ID, Universal Code ID, Universal Length
If you have changed data format settings, and wish to clear all formats and return
to the factory defaults, scan the Default Data Format code on page 5-5.
Step 1. Scan the Enter Data Format symbol (page 5-5).
Step 2. Primary/Alternate Format
Determine if this will be your primary data format, or one of 3 alternate
formats. (Alternate formats allow you “single shot” capability to scan
one barcode using a different data format. After the one barcode has
been read, the imager reverts to the primary data format. See page 5-
6.) If you are programming the primary format, scan 0 using the Pro-
gramming Chart inside the back cover of this manual. If you are pro-
gramming an alternate format, scan 1, 2, or 3, depending on the
alternate format you are programming.
Step 3. Terminal Type
Refer to Supported Terminals (page 2-2) and locate the Terminal ID
number for your PC. Scan three numeric barcodes on the inside back
cover to program the imager for your terminal ID (you must enter 3 dig-
its). For example, scan 0 0 3 for an AT wedge.
Note: The wildcard for all terminal types is 099.
4600rp, 4600g/4600r, 4800i User’s Guide
5 - 1
Step 4. Code I.D.
In Appendix A, find the symbology to which you want to apply the data
format. Locate the Hex value for that symbology and scan the 2 digit
manual.
Step 5. Length
Specify what length (up to 9999 characters) of data will be acceptable
for this symbology. Scan the four digit data length from the Program-
ming Chart inside the back cover of this manual. (Note: 50 characters is
entered as 0050. 9999 is a universal number, indicating all lengths.)
Step 6. Editor Commands
Refer to Data Format Editor Commands (page 5-2). Scan the symbols
acters may be entered for each symbology data format.
Step 7. Scan Save from the Programming Chart inside the back cover of this
Other Programming Selections
•
Clear One Data Format
primary format, scan 0 from the Programming Chart inside the back cover of
this manual. If you are clearing an alternate format, scan 1, 2, or 3, depending
on the alternate format you are clearing. Scan the Terminal Type and Code
I.D. (see Supported Terminals on page 2-2), and the barcode data length for
the specific data format that you want to delete. All other formats remain
unaffected.
•
•
Save from the Programming Chart inside the back cover of this manual
This exits, saving any Data Format changes.
This exits without saving any Data Format changes.
Data Format Editor Commands
Send Commands
F2 Send “nn” characters followed by “xx” key or function code, starting from
current cursor position. Syntax = F2nnxx (nn stands for the numeric value
(00-99) for the number of characters and xx stands for the hex value for an
ASCII code. See ASCII Conversion Chart (Code Page 1252), page A-4.)
F3 Send up to but not including “ss” character (Search and Send) starting from
current cursor position, leaving cursor pointing to “ss” character followed by
“xx” key or function code. Syntax = F3ssxx (ss and xx both stand for the
hex values for ASCII codes, see ASCII Conversion Chart (Code Page
1252), page A-4.)
5 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
F4 Send “xx” character “nn” times (Insert) leaving cursor in current cursor posi-
tion. Syntax = F4xxnn (xx stands for the hex value for an ASCII code, see
ASCII Conversion Chart (Code Page 1252), page A-4, and nn is the
numeric value (00-99) for the number of times it should be sent.)
E9 Send all but the last “nn” characters, starting from the current cursor posi-
tion. Syntax = E9nn (nn is the numeric value (00-99) for the number of
characters that will not be sent at the end of the message.)
Move Commands
F5 Move the cursor ahead “nn” characters from current cursor position.
Syntax = F5nn (nn stands for the numeric value (00-99) for the number of
characters the cursor should be moved ahead.)
Syntax = F6nn (nn stands for the numeric value (00-99) for the number of
characters the cursor should be moved back.)
EA Move the cursor to the end of the data string. Syntax = EA
Search Commands
pointing to “xx” character. Syntax = F8xx (xx stands for the hex value for
an ASCII code, see ASCII Conversion Chart (Code Page 1252), page A-4.)
an ASCII code, see ASCII Conversion Chart (Code Page 1252), page A-4.)
E6 Search ahead for the first non “xx” character from the current cursor posi-
tion, leaving cursor pointing to non “xx” character. Syntax = E6xx (xx
stands for the hex value for an ASCII code, see ASCII Conversion Chart
(Code Page 1252), page A-4.
E7 Search back for the first non “xx” character from the current cursor position,
leaving cursor pointing to non “xx” character. Syntax = E7xx (xx stands for
the hex value for an ASCII code, see ASCII Conversion Chart (Code Page
1252), page A-4.)
Miscellaneous Commands
FB Suppress all occurrences of up to 15 different characters, starting at the cur-
rent cursor position, as the cursor is advanced by other commands. When
the FC command is encountered, the suppress function is terminated. The
cursor is not moved by the FB command. Syntax = FBnnxxyy . .zz where
nn is a count of the number of suppressed characters in the list and xxyy ..
zz is the list of characters to be suppressed. (xx stands for the hex value for
an ASCII code, see ASCII Conversion Chart (Code Page 1252), page A-4.)
FC Disables suppress filter and clear all suppressed characters. Syntax = FC.
ters. Replacement continues until the E5 command is encountered. Syn-
tax = E4nnxx xx yy yy ...zz zz where nn is the total count of both
1
2
1
2
1
2
characters to be replaced plus replacement characters; xx defines charac-
1
4600rp, 4600g/4600r, 4800i User’s Guide
5 - 3
ters to be replaced and xx defines replacement characters, continuing
2
through zz and zz .
1
2
E5 Terminates character replacement. Syntax = E5.
FE Compare character in current cursor position to the character “xx.” If char-
acters are equal, increment cursor. If characters are not equal, no format
match. Syntax = FExx (xx stands for the hex value for an ASCII code, see
ASCII Conversion Chart (Code Page 1252), page A-4.)
EC Check to make sure there is an ASCII number at the current cursor position.
If character is not numeric, format is aborted. Syntax = EC.
ED Check to make sure there is a non-numeric ASCII character at the current
cursor position. If character is numeric, format is aborted. Syntax = ED.
5 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
Data Format Editor
Enter Data Format
* Default Data Format
Clear All Data Formats
Discard
Clear One Data Format
Save
Data Formatter
When Data Formatter is turned off, the barcode data is output to the host as read
(including prefixes and suffixes). Choose one of the following options. Default =
Data Formatter On, but Not Required.
* Data Formatter On,
but Not Required
Data Formatter Off
When Data Formatter is required, all input data must conform to an edited format
or the imager does not transmit the input data to the host device.
4600rp, 4600g/4600r, 4800i User’s Guide
5 - 5
Alternate Data Formats
Alternate formats allow you “single shot” capability to scan one barcode using a
different data format than your primary format. When data formats are
programmed (see page 5-1), you must input whether you are programming the
primary format, or an alternate format numbered 1, 2, or 3.
An alternate format is initiated by scanning one of the 3 alternate format
barcodes below. The imager will scan the next barcode, formatting the data with
the selected alternate format, then revert immediately to the primary format.
Alternate Data Format 1
Alternate Data Format 2
Alternate Data Format 3
5 - 6
4600rp, 4600g/4600r, 4800i User’s Guide
6
Secondary Interface
By switching secondary interface cables, the imager can, for example,
communicate with a portable data terminal (secondary interface) in addition to
the host terminal (primary interface). Refer to the table below for interfaces
supported by your model. Some features don’t apply if the interface is not
supported by your model.
Imager Models
Models
Primary
Secondary
4600gXX03XX
4800iXX03XX
True RS-232
True RS-232
4600gXX05XX
4800iXX05XX
Keyboard wedge, TTL level
232, TTL level 232 serial
Wand Emulation, TTL
level 232
wedge, IBM 4683, wand emula-
tion, USB keyboard, USB HID,
USB retail (IBM SurePOS),
USB COM port emulation
4600rXX05XX
4600rpXX05XX
Keyboard wedge, TTL level
232, TTL level 232 serial
wedge, IBM 4683, USB key-
board, USB HID, USB retail
(IBM SurePOS), USB COM
port emulation
TTL level 232
TTL level 232
Keyboard wedge, TTL level
232, TTL level 232 serial
wedge, IBM 4683, USB key-
board, USB HID, USB retail
(IBM SurePOS), USB COM
port emulation
The secondary interface can be programmed at any time.
4600rp, 4600g/4600r, 4800i User’s Guide
6 - 1
You can temporarily disable the secondary interface, but still retain the
secondary interface settings in the imager’s memory by scanning the Disable
barcode below. To re-enable the secondary interface, scan the Enable barcode.
Default =Disable.
* Disable
Enable
Secondary RS-232 Connection
All communication parameters between the imager and terminal must match for
correct data transfer through the serial port using RS-232 protocol.
RS-232 programmable selections are used by both the primary and secondary
interfaces. Changing an RS-232 parameter (e.g., baud rate or parity), while in
primary or secondary mode will affect both interfaces. If you want to change the
RS-232 settings, refer to RS-232 Baud Rate, page 2-10.
RS-232 Interface
Secondary Code 39 Wand Emulation
Note: See "Imager Models" on page 6-1 to determine which interfaces apply to
your imager.
In Wand Emulation mode, the imager decodes the barcode then sends data in
the same format as a wand imager. The Code 39 Format converts all
symbologies to Code 39. The Same Code Format transmits UPC, EAN, Code
128, Codabar, and Interleaved 2 of 5 without any changes, but converts all other
symbologies to Code 39. 2D symbologies are converted to Code 128. These
codes set the transmission rate to 25 inches per second and the output polarity
to black, high. Default = Code 39 Format.
6 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
The Code 39 Format barcode below sets the terminal ID to 61, and the Same
Code Format barcode sets the terminal ID to 64.
Wand Emulation
Same Code Format
Wand Emulation
Wand Emulation Multi Block
Note: See "Imager Models" on page 6-1 to determine which interfaces apply to
your imager.
Note: Changing secondary wand emulation settings also changes the primary
wand emulation settings (see Wand Emulation on page 2-14).
Delay Between Blocks
This sets the delay time between data blocks. Default = 50ms.
5ms
* 50ms
150ms
500ms
4600rp, 4600g/4600r, 4800i User’s Guide
6 - 3
Overall Checksum
When this option is turned on, a computed check character is added at the end
of the entire message. The check character is the character which when
Exclusive-OR’d with every preceding character of the message yields a result of
0x00 (00H). Default = Off.
On
* Off
Wand Emulation Transmission Rate
The Transmission Rate is limited by the terminal’s ability to receive data without
dropping characters. Default = 25 inches/second.
10
* 25
40
80
120
150
200
6 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
Wand Emulation Polarity
The Polarity can be sent as standard with black bars high, or reversed with white
bars high. Default = Black High.
* Black High
White High
Wand Emulation Idle
The idle describes the state of the imager when no data is being transmitted.
When in Wand Emulation mode, you must set the imager’s idle state to match
the idle state for the device to which the imager is connected. Default = Idle High.
* Idle High
Idle Low
Data Block Size
This transmits the data in smaller blocks to prevent buffer overflow. Default = 40.
20
* 40
60
80
4600rp, 4600g/4600r, 4800i User’s Guide
6 - 5
Secondary Trigger Mode
Manual/Serial Trigger
You can activate the imager either by pressing the trigger, or using a serial trigger
command (see Trigger Commands on page 12-4). When in manual trigger
mode, the imager scans until a barcode is read, or until the trigger is released.
When in serial mode, the imager scans until a barcode has been read or until the
deactivate command is sent. In serial mode, the imager can also be set to turn
itself off after a specified time has elapsed (see Read Time-Out, which follows).
* Manual/Serial Trigger
Read Time-Out
Use this selection to set a time-out (in milliseconds) of the imager’s trigger when
using serial commands to trigger the imager, or if the imager is in manual trigger
mode. Once the imager has timed out, you can activate the imager either by
pressing the trigger or using a serial trigger command. After scanning the Read
Time-Out barcode, set the time-out duration (from 0-300,000 milliseconds) by
scanning digits from the inside back cover, then scanning Save. Default =
30,000.
Read Time-Out
Note: Programming Read Time-Out in the secondary interface also programs it
in the primary interface.
Manual Trigger, Low Power
Note: Does not apply to the 4600g/4600r/4600rp/4800i with Advanced
Illumination.
The imager powers down until the trigger is pulled. When the trigger is pulled,
the imager powers up and operates until there is no triggering for the time set
with the Low Power Time-Out barcode below. There is a delay of up to one
second in operation when the imager is first triggered, but there is no delay when
operating in low power time-out mode.
Manual Trigger, Low Power
Note: Manual Trigger, Low Power cannot be used with keyboard wedge
applications.
6 - 6
4600rp, 4600g/4600r, 4800i User’s Guide
Low Power Time-Out Timer
Scan the Low Power Time-Out barcode to change the time-out duration (in
seconds). Then scan the time-out duration (from 0-300 seconds) from the inside
back cover, and Save. Default = 120 seconds.
If the unit remains idle during the low power time-out interval, the unit goes into
low power mode. Whenever the trigger is enabled, the low power time-out timer
is reset.
Low Power Time-Out
Note: This time-out does not begin until the imager time-out setting has expired.
Note: Programming Low Power Time-Out in the secondary interface also
programs it in the primary interface.
Hands Free Time-Out
The Automatic Trigger and Presentation Modes are referred to as “hands free”
modes. If the imager’s trigger is pulled when using a hands free mode, the
imager changes to manual trigger mode. You can set the time the imager should
remain in manual trigger mode by setting the Hands Free Time-Out. Once the
time-out value is reached, (if there have been no further trigger pulls) the imager
reverts to the original hands free mode.
Note: If you change the time-out duration for the secondary interface, the
duration of the primary interface will also be changed.
Scan the Hands Free Time-Out barcode, then scan the time-out duration (from
0-300,000 milliseconds) from the inside back cover, and Save. Default = 5,000
ms.
Hands Free Time-Out
4600rp, 4600g/4600r, 4800i User’s Guide
6 - 7
Scan Stand Mode
Note: Scan Stand Mode is only available for non-advanced illumination units
with software revision 31205480-090 or older. Refer to the Show
Software Revision on page 11-2 for information on determining the
software in your unit.
When a unit is in Scan Stand mode, it remains idle as long as it sees the Scan
Stand symbol. (See Scan Stand Symbol that follows.) When a different code
is presented, the Imager is triggered to read the new code.
Note: The imager automatically adjusts the illumination LEDs to the lowest light
level possible to maintain a good lock on the Scan Stand symbol. When
a symbol is presented, the imager’s light levels adjust to the saved setting
(see LED Power Level on page 3-9).
Scan Stand Mode
Scan Stand Symbol
When a unit is in Scan Stand mode, the LEDs shine at the Scan Stand symbol
on the base of the stand which tells it to remain idle. When the Scan Stand
symbol is covered, the imager turns the LEDs on at the configured power level
(Default High) and attempts to find and decode barcodes in its field of view.
Scan Stand Symbol
Presentation Mode
This programs the imager to work in Presentation mode. The LEDs are either off
or at the lowest power for ambient conditions until a barcode is presented to the
imager. Then the LEDs turn on automatically to read the code. Presentation
Mode uses ambient light to detect the barcodes. If the light level in the room is
not high enough, Presentation Mode may not work properly.
Presentation Mode
6 - 8
4600rp, 4600g/4600r, 4800i User’s Guide
7
Symbologies
Chapter 12 for settings and defaults.
•
•
•
All Symbologies
•
•
Interleaved 2 of 5
ID-tag (UPU 4-State)
Japanese Post
Australian Post
Kix (Netherlands)
Post
•
Aztec Code
•
•
•
•
•
•
•
•
•
•
•
•
British Post
Canadian Post
China Post
Codabar
•
•
•
•
•
•
•
•
•
•
Korea Post
Matrix 2 of 5
MaxiCode
MicroPDF417
MSI
Codablock F
Code 11
PDF417
Code 128
Code 16K
Code 39
Plessey Code
PosiCode A and B
Code 49
Code 93
Data Matrix
Straight 2 of 5 IATA
Straight 2 of 5
Industrial
•
•
EAN/JAN-13
EAN/JAN-8
•
TCIF Linked Code 39
(TLC39)
•
•
EAN•UCC Composite Codes
GS1 DataBar Omnidirectional
•
•
•
Telepen
UPC-A
UPC-A/EAN-13 with
Extended Coupon
Code
•
•
GS1 DataBar Limited
GS1 DataBar Expanded
•
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 1
All Symbologies
If you want to decode all the symbologies allowable for your imager, scan the All
Symbologies On code. If on the other hand, you want to decode only a
particular symbology, scan All Symbologies Off followed by the On symbol for
that particular symbology.
All Symbologies On
All Symbologies Off
Message Length Description
You are able to set the valid reading length of some of the barcode symbologies.
If the data length of the scanned barcode doesn’t match the valid reading length,
the imager will issue an error beep. You may wish to set the same value for
minimum and maximum length to force the imager to read fixed length barcode
data. This helps reduce the chances of a misread.
EXAMPLE:Decode only those barcodes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE:Decode only those barcodes with a count of 15 characters.
Min. length = 15 Max. length = 15
For a value other than the minimum and maximum message length defaults,
scan the barcodes included in the explanation of the symbology, then scan the
digit value of the message length and Save barcodes on the Programming Chart
inside the back cover of this manual. The minimum and maximum lengths and
the defaults are included with the respective symbologies.
7 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
Codabar
Codabar
<Default All Codabar Settings>
* On
Off
Codabar Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the barcode. You
may either transmit, or not transmit Start/Stop characters.
Default = Don’t Transmit.
Transmit
* Don’t Transmit
Codabar Check Character
Codabar check characters are created using different “modulos.” You can
program the imager to read only Codabar barcodes with Modulo 16 check
characters. Default = No Check Character.
No Check Character indicates that the imager reads and transmits barcode data
with or without a check character.
When Check Character is set to Validate and Transmit, the imager will only
character at the end of the scanned data.
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 3
When Check Character is set to Validate, but Don’t Transmit, the unit will only
read Codabar barcodes printed with a check character, but will not transmit the
check character with the scanned data.
* No Check Character
Validate Modulo 16, but
Don’t Transmit
Validate Modulo 16
and Transmit
Codabar Concatenation
Codabar supports symbol concatenation. When you enable concatenation, the
imager looks for a Codabar symbol having a “D” start character, adjacent to a
symbol having a “D” stop character. In this case the two messages are
concatenated into one with the “D” characters omitted. Default = On.
Character
Start
Stop
Start
Stop
Codabar
A12D
D34A
7 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
Select Require to prevent the imager from decoding a single “D” Codabar symbol
without its companion. This selection has no effect on Codabar symbols without
Stop/Start D characters.
On
* Off
Require
Codabar Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60.
Minimum Message Length
Maximum Message Length
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 5
Code 39
Code 39
< Default All Code 39 Settings >
* On
Off
Code 39 Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the barcode. You
may either transmit, or not transmit Start/Stop characters. Default = Don’t
Transmit.
Transmit
* Don’t Transmit
Code 39 Check Character
No Check Character indicates that the imager reads and transmits barcode data
with or without a check character.
7 - 6
4600rp, 4600g/4600r, 4800i User’s Guide
When Check Character is set to Validate, but Don’t Transmit, the unit only
reads Code 39 barcodes printed with a check character, but will not transmit the
check character with the scanned data.
When Check Character is set to Validate and Transmit, the imager only reads
Code 39 barcodes printed with a check character, and will transmit this character
at the end of the scanned data. Default = No Check Character.
* No Check Character
Validate and Transmit
Code 39 Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 0-48. Minimum Default = 0, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 7
Code 39 Append
This function allows the imager to append the data from several Code 39
barcodes together before transmitting them to the host computer. When this
function is enabled, the imager stores those Code 39 barcodes that start with a
space (excluding the start and stop symbols), and does not immediately transmit
the data. The imager stores the data in the order in which the barcodes are read,
deleting the first space from each. The imager transmits the appended data
when it reads a Code 39 barcode that starts with a character other than a space.
Default = Off.
On
* Off
Code 32 Pharmaceutical (PARAF)
Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian
pharmacies. This symbology is also known as PARAF.
7 - 8
4600rp, 4600g/4600r, 4800i User’s Guide
Note: Trioptic Code (page 7-34) must be turned off while scanning Code 32
Pharmaceutical codes.
On
* Off
Full ASCII
If Full ASCII Code 39 decoding is enabled, certain character pairs within the
barcode symbol will be interpreted as a single character. For example: $V will
be decoded as the ASCII character SYN, and /C will be decoded as the ASCII
character #. Default = Off.
NUL %U
DLE $P
SP
SPACE
0
0
@
%V
P
P
‘
%W
p
+P
SOH $A
STX $B
ETX $C
EOT $D
ENQ $E
ACK $F
BEL $G
BS $H
HT $I
DC1 $Q
DC2 $R
DC3 $S
DC4 $T
NAK $U
SYN $V
ETB $W
CAN $X
EM $Y
SUB $Z
ESC %A
FS %B
GS %C
RS %D
US %E
!
/A
1
2
3
4
5
6
7
8
9
:
1
A
B
C
D
E
F
G
H
I
A
B
C
D
E
F
G
H
I
Q
R
S
T
U
V
W
X
Y
Z
[
Q
a
b
c
d
e
f
+A
+B
+C
+D
+E
+F
+G
+H
+I
q
r
+Q
+R
+S
“
/B
/C
/D
/E
/F
/G
/H
/I
2
R
#
$
%
&
‘
3
S
s
t
4
T
+T
5
U
u
v
w
x
y
z
{
+U
+V
6
V
7
W
X
g
h
i
+W
+X
(
8
)
9
Y
+Y
LF $J
VT $K
FF $L
CR $M
SO $N
*
+
,
/J
/K
/L
-
/Z
%F
%G
%H
%I
%J
J
J
Z
j
+J
+Z
;
K
L
K
L
%K
%L
%M
%N
%O
k
l
+K
+L
+M
+N
%P
%Q
%R
%S
<
=
>
?
\
|
-
M
N
O
M
N
O
]
m
n
o
}
.
.
^
~
SI
$O
/
/O
_
+O DEL %T
Character pairs /M and /N decode as a minus sign and period respectively.
Character pairs /P through /Y decode as 0 through 9.
Full ASCII On
* Full ASCII Off
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 9
Code 39 Code Page
Code pages define the mapping of character codes to characters. If the data
received does not display with the proper characters, it may be because the
barcode being scanned was created using a code page that is different from the
one the host program is expecting. If this is the case, scan the barcode below,
select the code page with which the barcodes were created (see Code Page
Mapping of Printed Barcodes on page A-6), and scan the value and the Save
barcode from the Programming Chart on the inside the back cover of this
manual. The data characters should then appear properly.
Code 39 Code Page
Interleaved 2 of 5
< Default All Interleaved 2 of 5 Settings >
Interleaved 2 of 5
* On
Off
Check Digit
No Check Digit indicates that the imager reads and transmits barcode data with
or without a check digit.
When Check Digit is set to Validate, but Don’t Transmit, the unit only reads
Interleaved 2 of 5 barcodes printed with a check digit, but will not transmit the
check digit with the scanned data.
7 - 10
4600rp, 4600g/4600r, 4800i User’s Guide
When Check Digit is set to Validate and Transmit, the imager only reads
Interleaved 2 of 5 barcodes printed with a check digit, and will transmit this digit
at the end of the scanned data. Default = No Check Digit.
* No Check Digit
Validate and Transmit
Interleaved 2 of 5 Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 11
Code 93
Code 93
< Default All Code 93 Settings >
* On
Off
Code 93 Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
Minimum Message Length
Code 93 Code Page
Code pages define the mapping of character codes to characters. If the data
received does not display with the proper characters, it may be because the
barcode being scanned was created using a code page that is different from the
one the host program is expecting. If this is the case, scan the barcode below,
select the code page with which the barcodes were created (see Code Page
Mapping of Printed Barcodes on page A-6), and scan the value and the Save
barcode from the Programming Chart on the inside the back cover of this
manual. The data characters should then appear properly.
Code 93 Code Page
7 - 12
4600rp, 4600g/4600r, 4800i User’s Guide
Straight 2 of 5 Industrial
<Default All Straight 2 of 5 Industrial Settings>
Straight 2 of 5 Industrial
On
* Off
Straight 2 of 5 Industrial Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 13
Straight 2 of 5 IATA (Two-Bar Start/Stop)
<Default All Straight 2 of 5 IATA Settings>
Straight 2 of 5 IATA
On
* Off
Straight 2 of 5 IATA Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
7 - 14
4600rp, 4600g/4600r, 4800i User’s Guide
Matrix 2 of 5
<Default All Matrix 2 of 5 Settings>
Matrix 2 of 5
On
* Off
Matrix 2 of 5 Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
Code 11
<Default All Code 11 Settings>
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 15
Code 11
On
* Off
Check Digits Required
This option sets whether 1 or 2 check digits are required with Code 11 barcodes.
Default = Two Check Digits.
One Check Digit
* Two Check Digits
Code 11 Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
7 - 16
4600rp, 4600g/4600r, 4800i User’s Guide
Code 128
Code 128
<Default All Code 128 Settings>
* On
Off
ISBT 128 Concatenation
In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard
for communicating critical blood information in a uniform manner. The use of
ISBT formats requires a paid license. The ISBT 128 Application Specification
describes 1) the critical data elements for labeling blood products, 2) the current
recommendation to use Code 128 due to its high degree of security and its
space-efficient design, 3) a variation of Code 128 that supports concatenation of
neighboring symbols, and 4) the standard layout for barcodes on a blood product
label. Use the barcodes below to turn concatenation on or off. Default =Off.
On
* Off
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 17
Code 128 Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
Minimum Message Length
Code 128 Code Page
Code pages define the mapping of character codes to characters. If the data
received does not display with the proper characters, it may be because the
barcode being scanned was created using a code page that is different from the
one the host program is expecting. If this is the case, scan the barcode below,
select the code page with which the barcodes were created (see Code Page
Mapping of Printed Barcodes on page A-6), and scan the value and the Save
barcode from the Programming Chart on the inside the back cover of this
manual. The data characters should then appear properly.
Code 128 Code Page
7 - 18
4600rp, 4600g/4600r, 4800i User’s Guide
Telepen
Telepen
<Default All Telepen Settings>
On
* Off
Telepen Output
Using AIM Telepen Output, the imager reads symbols with start/stop pattern 1
and decodes them as standard full ASCII (start/stop pattern 1). When Original
Telepen Output is selected, the imager reads symbols with start/stop pattern 1
and decodes them as compressed numeric with optional full ASCII (start/stop
pattern 2). Default = AIM Telepen Output.
* AIM Telepen Output
Original Telepen Output
Telepen Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-60. Minimum Default = 1, Maximum Default = 60.
Minimum Message Length
Maximum Message Length
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 19
UPC-A
UPC-A
<Default All UPC-A Settings>
* On
Off
UPC-A Check Digit
This selection allows you to specify whether the check digit should be transmitted
at the end of the scanned data or not. Default = On.
* On
Off
UPC-A Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the
beginning of the scanned data, but the unit can be programmed so it will not
transmit it. Default = On.
* On
Off
7 - 20
4600rp, 4600g/4600r, 4800i User’s Guide
UPC-A Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC-A data.
Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
UPC-A Addenda Required
When Required is scanned, the imager will only read UPC-A barcodes that have
addenda. You must then turn on a 2 or 5 digit addenda listed on page 7-21.
Default = Not Required.
Required
* Not Required
UPC-A Addenda Separator
When this feature is on, there is a space between the data from the barcode and
the data from the addenda. When turned off, there is no space.
Default = On.
* On
Off
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 21
UPC-A/EAN-13
with Extended Coupon Code
Use the following codes to enable or disable UPC-A and EAN-13 with Extended
Coupon Code. Default = On.
* On
Off
UPC-E0
<Default All UPC-E Settings>
UPC-E0
Most U.P.C. barcodes lead with the 0 number system. For these codes, use the
UPC-E0 selection. If you need to read codes that lead with the 1 number system,
use UPC-E1 (page 7-24). Default = On.
* UPC-E0 On
UPC-E0 Off
UPC-E0 Expand
UPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format.
Default = Off.
On
* Off
7 - 22
4600rp, 4600g/4600r, 4800i User’s Guide
UPC-E0 Addenda Required
When Addenda Required is set to on, the imager will only read UPC-E barcodes
that have addenda. Default = Not Required.
Required
* Not Required
UPC-E0 Addenda Separator
When this feature is on, there is a space between the data from the barcode and
the data from the addenda. When turned off, there is no space.
Default = On.
* On
Off
UPC-E0 Check Digit
Check Digit specifies whether the check digit should be transmitted at the end of
the scanned data or not. Default = On.
* On
Off
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 23
UPC-E0 Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the
beginning of the scanned data, but the unit can be programmed so it will not
transmit it. Default = On.
* On
Off
UPC-E0 Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC-E data.
Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
UPC-E1
Most U.P.C. barcodes lead with the 0 number system. For these codes, use
UPC-E0 (page 7-22). If you need to read codes that lead with the 1 number
system, use the UPC-E1 selection. Default = Off.
UPC-E1 On
* UPC-E1 Off
7 - 24
4600rp, 4600g/4600r, 4800i User’s Guide
EAN/JAN-13 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data.
Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
EAN/JAN-13 Addenda Required
When Addenda Required is set to on, the imager will only read EAN/JAN-13
barcodes that have addenda. Default = Not Required.
Required
* Not Required
EAN/JAN-13 Addenda Separator
When this feature is on, there is a space between the data from the barcode and
the data from the addenda. When turned off, there is no space.
Default = On.
* On
Off
7 - 26
4600rp, 4600g/4600r, 4800i User’s Guide
Note: If you want to enable or disable EAN13 with Extended Coupon Code,
refer to UPC-A/EAN-13 with Extended Coupon Code (page 7-22).
ISBN Translate
This selection causes EAN-13 Bookland symbols to be translated into their
equivalent ISBN number format. Default = Off.
On
* Off
EAN/JAN-8
<Default All EAN/JAN-8 Settings>
EAN/JAN-8
* On
Off
EAN/JAN-8 Check Digit
This selection allows you to specify whether the check digit should be transmitted
at the end of the scanned data or not. Default = On.
* On
Off
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 27
EAN/JAN-8 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data.
Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
EAN/JAN-8 Addenda Required
When Addenda Required is set to on, the imager will only read EAN/JAN-8
barcodes that have addenda. Default = Not Required.
Required
* Not Required
EAN/JAN-8 Addenda Separator
When this feature is on, there is a space between the data from the barcode and
the data from the addenda. When turned off, there is no space.
Default = On.
* On
Off
7 - 28
4600rp, 4600g/4600r, 4800i User’s Guide
MSI
MSI
<Default All MSI Settings>
On
* Off
MSI Check Character
Different types of check characters are used with MSI barcodes. You can
program the imager to read MSI barcodes with Type 10 check characters.
Default = Validate Type 10, but Don’t Transmit.
When Check Character is set to Validate and Transmit, the imager will only
read MSI barcodes printed with the specified type check character, and will
transmit this character at the end of the scanned data.
When Check Character is set to Validate, but Don’t Transmit, the unit will only
read MSI barcodes printed with the specified type check character, but will not
transmit the check character with the scanned data.
* Validate Type 10, but Don’t
Transmit
Validate Type 10 and Transmit
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 29
MSI Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
Plessey Code
<Default All Plessey Code Settings>
Plessey Code
On
* Off
Plessey Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
7 - 30
4600rp, 4600g/4600r, 4800i User’s Guide
GS1 DataBar Omnidirectional
< Default All GS1 DataBar Omnidirectional Settings >
GS1 DataBar Omnidirectional
* On
Off
GS1 DataBar Limited
< Default All GS1 DataBar Limited Settings >
GS1 DataBar Limited
* On
Off
GS1 DataBar Expanded
< Default All GS1 DataBar Expanded Settings >
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 31
GS1 DataBar Expanded
* On
Off
GS1 DataBar Expanded Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74.
Minimum Message Length
Maximum Message Length
7 - 32
4600rp, 4600g/4600r, 4800i User’s Guide
PosiCode
<Default All PosiCode Settings>
PosiCode A and B
* On
Off
You have to have PosiCode A and B on to read any of the PosiCode
symbologies.
A and B On
(No Limited)
A and B and Limited A On
* A and B and Limited B On
(Limited A Off)
PosiCode Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 33
Trioptic Code
Note: If you are going to scan Code 32 Pharmaceutical codes (page 7-8),
Trioptic Code must be off.
Trioptic Code is used for labeling magnetic storage media.
On
* Off
Codablock F
<Default All Codablock F Settings>
Codablock F
On
* Off
Codablock F Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048.
Minimum Message Length
Maximum Message Length
7 - 34
4600rp, 4600g/4600r, 4800i User’s Guide
Code 16K
Code 16K
<Default All Code 16K Settings>
On
* Off
Code 16K Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 0-160. Minimum Default = 1, Maximum Default = 160.
Minimum Message Length
Maximum Message Length
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 35
Code 49
Code 49
<Default All Code 49 Settings>
* On
Off
Code 49 Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-81. Minimum Default = 1, Maximum Default = 81.
Minimum Message Length
Maximum Message Length
7 - 36
4600rp, 4600g/4600r, 4800i User’s Guide
PDF417
PDF417
< Default All PDF417 Settings >
* On
Off
PDF417 Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750.
Minimum Message Length
Maximum Message Length
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 37
MicroPDF417
< Default All MicroPDF417 Settings >
MicroPDF417
On
* Off
MicroPDF417 Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366.
Minimum Message Length
Maximum Message Length
EAN•UCC Composite Codes
Linear codes are combined with a unique 2D composite component to form a
new class called EAN•UCC Composite symbology. EAN•UCC Composite
symbologies allow for the co-existence of symbologies already in use.
On
* Off
7 - 38
4600rp, 4600g/4600r, 4800i User’s Guide
UPC/EAN Version
Scan the UPC/EAN Version On barcode to decode EAN•UCC Composite
symbols that have a UPC or EAN linear component. (This does not affect
EAN•UCC Composite symbols with a UCC/EAN-128 or GS1linear component.
If either of these codes are the linear component, either Code 128 or the correct
GS1 code must be enabled.)
* UPC/EAN Version Off
EAN•UCC Composite Code Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-2435. Minimum Default = 1, Maximum Default = 2435.
Minimum Message Length
Maximum Message Length
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 39
EAN•UCC Emulation
The imager can automatically format the output from any EAN•UCC data carrier
to emulate what would be encoded in an equivalent UCC/EAN-128 or GS1 and
Composite symbol. EAN•UCC data carriers include UPC-A and UPC-E, EAN-
13 and EAN-8, ITF-14, UCC/EAN-128, and EAN•UCC GS1 and Composites.
Data from 2D symbols such as Aztec Code, Data Matrix, or QR Code, which
encode a leading FNC1, also invoke EAN•UCC emulation. If UCC/EAN-128
Emulation is selected, the AIM Symbology Identifier is reported as “]C1”. If GS1
Emulation is selected, the AIM Symbology Identifier is reported as “]e0.” Any
application that accepts EAN•UCC data can be simplified since it only needs to
recognize one data carrier type. Default = No Emulation.
GS1 Emulation
128 Emulation
* EAN•UCC Emulation Off
TCIF Linked Code 39 (TLC39)
This code is a composite code since it has a Code 39 linear component and a
MicroPDF417 stacked code component. All barcode readers are capable of
reading the Code 39 linear component. The MicroPDF417 component can only
be decoded if TLC39 On is selected. The linear component may be decoded as
Code 39 even if TLC39 is off.
On
* Off
7 - 40
4600rp, 4600g/4600r, 4800i User’s Guide
Postal Codes
Note: For best performance when reading a postal symbology, all other postal
symbologies should be turned off. The following postal codes can only be
read by a 2D Imager.
4-CB (4-State Customer Barcode)
Note: You may enable the 4-CB (4-State Customer Barcode) if you have
firmware with a base number of 31205480. Refer to the Show Software
Revision on page 11-2 for information on determining the firmware
revision in your unit.
On
* Off
ID-tag (UPU 4-State)
Note: You may enable the ID-tag (UPU 4-State) if you have firmware with a
base number of 31205480. Refer to the Show Software Revision on
page 11-2 for information on determining the firmware revision in your
unit.
On
* Off
Postnet
On
* Off
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 41
Postnet Check Digit
This selection allows you to specify whether the check digit should be transmitted
at the end of the scanned data.
Transmit Check Digit
* Don’t Transmit Check Digit
Planet Code
On
* Off
Planet Code Check Digit
This selection allows you to specify whether the check digit should be transmitted
at the end of the scanned data.
Transmit Check Digit
* Don’t Transmit Check Digit
7 - 42
4600rp, 4600g/4600r, 4800i User’s Guide
British Post
On
* Off
Canadian Post
On
* Off
Kix (Netherlands) Post
Note: Kix code can misread when scanned sideways or upside down. Use
Working Orientation, page 3-22, if your Kix codes will not usually be
presented upright to the imager.
On
* Off
Australian Post
On
* Off
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 43
Australian Post Interpretation
This option controls what interpretation is applied to customer fields in Australian
4-State symbols. Bar Output lists the bar patterns in “0123” format. Numeric N
Table causes that field to be interpreted as numeric data using the N Table.
Alphanumeric C Table causes the field to be interpreted as alphanumeric data
using the C Table. Refer to the Australian Post Specification Tables.
Note: You may enable the Australian Post Interpretation option if you have
firmware with a base number of 31205480. Refer to the Show Software
Revision on page 11-2 for information on determining the firmware
revision in your unit.
* Bar Output
Numeric N Table
Alphanumeric C Table
Japanese Post
On
* Off
7 - 44
4600rp, 4600g/4600r, 4800i User’s Guide
China Post
China Post
<Default All China Post Settings>
On
* Off
China Post Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 45
Korea Post
Korea Post
<Default All Korea Post Settings>
On
* Off
Korea Post Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
7 - 46
4600rp, 4600g/4600r, 4800i User’s Guide
QR Code
Note: QR Code can only be read by a 2D imager.
< Default All QR Code Settings >
QR Code
This selection applies to both QR Code and Micro QR Code.
* On
Off
Note: The default applies to firmware with a base number of 31205480. Refer
to the Show Software Revision on page 11-2 for information on
determining the firmware revision in your unit
QR Code Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-3500. Minimum Default = 1, Maximum Default = 3500.
Minimum Message Length
Maximum Message Length
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 47
Data Matrix
Note: Data Matrix can only be read by a 2D imager.
< Default All Data Matrix Settings >
Data Matrix
* On
Off
Data Matrix Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-1500. Minimum Default = 1, Maximum Default = 1500.
Minimum Message Length
Maximum Message Length
7 - 48
4600rp, 4600g/4600r, 4800i User’s Guide
MaxiCode
Note: MaxiCode can only be read by a 2D imager.
< Default All MaxiCode Settings >
MaxiCode
* On
Off
MaxiCode Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150.
Minimum Message Length
Maximum Message Length
4600rp, 4600g/4600r, 4800i User’s Guide
7 - 49
Aztec Code
Note: Aztec Code can only be read by a 2D imager.
< Default All Aztec Code Settings >
Aztec Code
* On
Off
Aztec Code Message Length
Scan the barcodes below to change the message length. Refer to Message
Length Description (page 7-2) for additional information. Minimum and
Maximum lengths = 1-3750. Minimum Default = 1, Maximum Default = 3750.
Minimum Message Length
Maximum Message Length
Aztec Runes
Select Enable Runes if you are scanning Aztec runes, which are the smallest
type of Aztec Code symbol with the ability to encode a very short license plate
message.
Enable Runes
* Disable Runes
7 - 50
4600rp, 4600g/4600r, 4800i User’s Guide
8
Imaging Commands
The image scanner is like a digital camera in the way it captures, manipulates,
and transfers images. The following commands allow you to alter the way the
Single-Use Basis
Imaging Commands with their modifiers send instructions to the imager on a
single-use basis, and take effect for a single image capture. Once that capture
is complete, the imager reverts to its imaging default settings. If you want to
permanently change a setting, you must use the serial default commands (see
Chapter 12). When the serial default command is used, that selection becomes
the new, permanent setting for the imager.
Command Syntax
Multiple modifiers and commands can be issued within one sequence. If
additional modifiers are to be applied to the same command, just add the
modifiers to that command. For example, to add 2 modifiers to the Image Snap
command, such as setting the Imaging Style to 1P and the Wait for Trigger to 1T,
you would enter IMGSNP1P1T.
terminal.
To add a command to a sequence, each new command is separated with a
semicolon. For example, to add the Image Ship command to the above
sequence, you would enter IMGSNP1P1T;IMGSHP.
The imaging commands are:
Image Snap - IMGSNP (page 8-2)
Image Ship - IMGSHP (page 8-6)
Intelligent Signature Capture - IMGBOX (page 8-16)
The modifiers for each of these commands follow the command description.
Note: The images included with each command description are examples only.
The results you achieve may be different from those included in this
manual. The quality of the output you receive will vary depending on
lighting, quality of the initial image/object being captured, and distance of
recommended that you position your imager 4-6" (122-183 cm) away from
the image/object you are capturing.
4600rp, 4600g/4600r, 4800i User’s Guide
8 - 1
Step 1 - Take a Picture Using IMGSNP
Image Snap - IMGSNP
An image is taken whenever the hardware button is pressed, or when the Image
Snap (IMGSNP) command is processed.
The image snap command has many different modifiers that can be used to
change the look of the image in memory. Modifiers always begin with numbers
and end with a letter (case insensitive). Any number of modifiers may be
appended to the IMGSNP command. For example, you can use the following
command to snap an image, increase the gain, and have the beeper sound once
the snap is complete:
IMGSNP2G1B
IMGSNP Modifiers
P - Imaging Style
This sets the Image Snap style.
0P
Decoding Style. This processing allows a few frames to be
taken until the exposure parameters are met. The last frame is
then available for further use.
1P
2P
Photo Style (default). This mimics a simple digital camera, and
results in a visually optimized image.
Manual Style. This is an advanced style that should only be
used by an experienced user. It allows you the most freedom to
set up the imager, and has no auto-exposure.
B - Beeper
Causes a beep to sound after an image is snapped.
0B
1B
No beep (default)
Sounds a beep when the image is captured.
T - Wait for Trigger
Waits for a hardware button push before taking the image. This is only
available when using Photo Style (1P).
0T
1T
Takes image immediately (default)
Waits for a button push, then takes the image
8 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
L - LED State
Determines if the LEDs should be on or off, and when. Ambient illumination
(0L) is preferred for taking pictures of color documents, such as ID cards,
especially when the imager is in a stand. LED illumination (1L) is preferred
when the imager is hand held. LED State is not available when using
Decoding Style (0P).
0L
1L
LEDs off (default)
LEDs on
E - Exposure
Exposure is used in Manual Style only (2P), and allows you to set the
exposure time. This is similar to setting a shutter speed on a camera. The
exposure time determines how long the imager takes to record an image.
On a bright day, exposure times can be very short because plenty of light is
available to help record an image. At nighttime, exposure time can increase
dramatically due to the near absence of light. Units are 127 microseconds.
(Default = 7874)
nE
Range: 1 - 7874
Example of Exposure at 7874E with
fluorescent lighting:
Example of Exposure at 100E with
fluorescent lighting:
4600rp, 4600g/4600r, 4800i User’s Guide
8 - 3
G - Gain
Gain is used in Manual Style only (2P). Like a volume control, the gain
modifier boosts the signal and multiplies the pixel value. As you increase the
gain, the noise in an image is also amplified.
1G
2G
4G
8G
No gain (default)
Medium gain
Heavy gain
Maximum gain
Example of Gain at 1G:
Example of Gain at 4G:
Example of Gain at 8G:
W - Target White Value
Sets the target for the median grayscale value in the captured image. For
capturing close-up images of high contrast documents, a lower setting, such
as 75, is recommended. Higher settings result in longer exposure times and
brighter images, but if the setting is too high, the image may be
overexposed. Target White Value is only available when using Photo Style
(1P). (Default = 125)
nW Range: 0 - 255
Example of White
Value at 75W:
Example of White
Value at 125W:
Example of White
Value at 200W:
D - Delta for Acceptance
This sets the allowable range for the white value setting (see W - Target
White Value). Delta is only available when using Photo Style (1P). (Default
= 25)
nD
Range: 0 - 255
U - Update Tries
This sets the maximum number of frames the imager should take to reach
the D - Delta for Acceptance. Update Tries is only available when using
Photo Style (1P). (Default = 6)
nU
Range: 0 - 10
8 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
% - Target Set Point Percentage
Sets the target point for the light and dark values in the captured image. A
setting of 75% means 75% of the pixels are at or below the target white
value, and 25% of the pixels are above the target white value. Altering this
setting from the default is not recommended under normal circumstances.
To alter grayscale values, W - Target White Value should be used. (Default
= 50)
n% Range: 1 - 99
Example of Target Set
Point Percentage at 40%:
Example of Target Set
Point Percentage at 50%:
Example of Target Set
Point Percentage at 97%:
4600rp, 4600g/4600r, 4800i User’s Guide
8 - 5
Step 2 - Ship a Picture Using IMGSHP
Image Ship - IMGSHP
An image is taken whenever the button is pressed, or when the Image Snap
(IMGSNP) command is processed. The last image is always stored in memory.
You can “ship” the image by using the IMGSHP command.
The image ship commands have many different modifiers that can be used to
change the look of the image output. Modifiers affect the image that is
transmitted, but do not affect the image in memory. Modifiers always begin with
a number and end with a letter (case insensitive). Any number of modifiers may
be appended to the IMGSHP command. For example, you can use the following
command to snap and ship a bitmap image with gamma correction and
document image filtering:
IMGSNP;IMGSHP8F75K26U
IMGSHP Modifiers
A - Infinity Filter
Enhances pictures taken from very long distances (greater than 10 feet or
3m). The Infinity Filter should not be used with IMGSHP Modifiers (page 8-
6).
0A
1A
Infinity filter off (default)
Infinity filter on
Example of Infinity Filter off (0A)
from approximately 12 feet (3.66m) away:
Example of Infinity Filter on (1A)
from approximately 12 feet (3.66m) away:
8 - 6
4600rp, 4600g/4600r, 4800i User’s Guide
C - Compensation
Flattens the image to account for variations in illumination across the image.
0C
1C
Compensation disabled (default)
Compensation enabled
Example of Compensation at 0C:
Example of Compensation at 1C:
D - Pixel Depth
Indicates the number of bits per pixel in the transmitted image (KIM or BMP
format only).
8D
1D
8 bits per pixel, grayscale image (default)
1 bit per pixel, black and white image
E - Edge Sharpen
An edge sharpen filter cleans up the edges of an image, making it look
cleaner and sharper. While edge sharpening does make the image look
cleaner, it also removes some fine detail from the original image. The
strength of the edge sharpen filter can be entered from 1 to 24. Entering a
23E gives the sharpest edges, but also increases noise in the image.
0E
14E Apply edge sharpen for typical image
ne Apply edge sharpen using strength n (n = 1-24)
Don’t sharpen image (default)
Example of Edge Sharpen at 0E:
Example of Edge Sharpen at 24E:
4600rp, 4600g/4600r, 4800i User’s Guide
8 - 7
F - File Format
Indicates the desired format for the image.
0F
1F
2F
3F
4F
KIM format
TIFF binary
TIFF binary group 4, compressed
TIFF grayscale
Uncompressed binary (upper left to lower right, 1 pixel/bit, 0
padded end of line)
5F
Uncompressed grayscale (upper left to lower right, bitmap
format)
6F
8F
JPEG image (default)
BMP format (lower right to upper left, uncompressed)
H - Histogram Stretch
Increases the contrast of the transmitted image. Not available with some
image formats.
0H
1H
No stretch (default)
Histogram stretch
Example of Histogram Stretch at 0H:
Example of Histogram Stretch at 1H:
8 - 8
4600rp, 4600g/4600r, 4800i User’s Guide
I - Invert Image
Invert image is used to rotate the image around the X or Y axis.
1ix
1iy
Invert around the X axis (flips picture upside down)
Invert around the Y axis (flips picture left to right)
Example of image not
inverted:
Example of image
with Invert Image set to 1ix:
Example of image
with Invert Image set to 1iy:
IF- Noise Reduction
Used to reduce the salt and pepper noise in an image.
0if
1if
No salt and pepper noise reduction (default)
Salt and pepper noise reduction
Example of Noise Reduction Off (0if):
Example of Noise Reduction On (1if):
4600rp, 4600g/4600r, 4800i User’s Guide
8 - 9
IR - Image Rotate
0ir
1ir
2ir
3ir
Image as snapped (rightside up) (default)
Rotate image 90 degrees to the right
Rotate image 180 degrees (upside down)
Rotate image 90 degrees to the left
Example of Image Rotate set to 2ir
:
Example of Image Rotate set to 0ir
:
Example of Image Rotate set to 1ir
:
Example of Image Rotate set to 3ir
:
J - JPEG Image Quality
Sets the desired quality when the JPEG image format is selected. Higher
numbers result in higher quality, but larger files. Smaller numbers result in
greater amounts of lossy compression, faster transmission times, lower
quality, but smaller files. (Default = 50)
nJ
Image is compressed as much as possible while preserving
quality factor of n (n = 0 - 100)
0J
worst quality (smallest file)
100J best quality (largest file)
8 - 10
4600rp, 4600g/4600r, 4800i User’s Guide
K - Gamma Correction
Gamma measures the brightness of midtone values produced by the image.
You can brighten or darken an image using gamma correction. A higher
gamma correction yields an overall brighter image. The lower the setting,
the darker the image. The optimal setting for text images is 50K.
0K
50K Apply gamma correction for brightening typical document image
nK Apply gamma correction factor n (n = 0-1,000)
Gamma correction off (default)
Example of Gamma
Correction set to 0K:
Example of Gamma
Correction set to 50K:
Example of Gamma
Correction set to 255K:
4600rp, 4600g/4600r, 4800i User’s Guide
8 - 11
L, R, T, B, M - Image Cropping
Note: Image Cropping should not be used with IMGSHP Modifiers (see
page 8-6).
Ships a window of the image by specifying the left, right, top, and bottom
pixel coordinates. Device columns are numbered 0 through 1279, and
device rows are numbered 0 through 959.
nL
The left edge of the shipped image corresponds to column n of
the image in memory. Range: 000 - 640. (Default = 0)
nR
The right edge of the shipped image corresponds to column n - 1
of the image in memory. Range: 000 - 640. (Default = all
columns)
nT
nB
The top edge of the shipped image corresponds to row n of the
image in memory. Range: 000 - 480. (Default = 0)
The bottom edge of the shipped image corresponds to row n - 1
of the image in memory. Range: 000 - 480. (Default = all rows)
Uncropped Image:
Example of Image
Crop set to 300R:
Example of Image
Crop set to 300L:
Example of Image Crop set to 200B:
Example of Image Crop set to 200T:
Alternately, specify the number of pixels to cut from the outside margin of the
image; thus only the center pixels are transmitted.
nM Margin: cut n columns from the left, n + 1 columns from the right,
n rows from the top, and n + 1 rows from the bottom of the image.
Ship the remaining center pixels. Range: 0 - 238.
(Default = 0, or full image)
Example of Image
Crop set to 238M:
8 - 12
4600rp, 4600g/4600r, 4800i User’s Guide
P - Protocol
Used for shipping an image. Protocol covers two features of the image data
being sent to the host. It addresses the protocol used to send the data
(Hmodem, which is an Xmodem 1K variant that has additional header
information), and the format of the image data that is sent.
0P
2P
3P
4P
None (raw data)
None (default for USB)
Hmodem compressed (default for RS-232)
Hmodem
S - Pixel Ship
Pixel Ship sizes an image in proportion to its original size. It decimates the
image by shipping only certain, regularly spaced pixels. For example, 4S
would transmit every fourth pixel from every fourth line. The smaller number
of pixels shipped, the smaller the image, however, after a certain point the
image becomes unusable.
1S
2S
3S
ship every pixel (default)
ship every 2nd pixel, both horizontally and vertically
ship every 3rd pixel, both horizontally and vertically
Example of Pixel Ship
set to 2S:
Example of Pixel
Ship set to 3S:
Example of Pixel Ship set to 1S:
U - Document Image Filter
Allows you to input parameters to sharpen the edges and smooth the area
between the edges of text in an image. This filter should be used with
gamma correction (see page 8-11), with the imager in a stand, and the
image captured using the command:
IMGSNP1P0L168W90%32D
4600rp, 4600g/4600r, 4800i User’s Guide
8 - 13
This filter typically provides better JPEG compression than the standard E -
Edge Sharpen command (see page 8-15). This filter also works well when
shipping pure black and white images (1 bit per pixel). The optimal setting
is 26U.
0U
Document image filter off (default)
26U Apply document image filter for typical document image
nU
Apply document image filter using grayscale threshold n. Use
lower numbers when the image contrast is lower. 1U will have a
similar effect to setting E - Edge Sharpen (page 8-7) to 22e.
Range: 0-255.
Example of Document Image
Filter set to 0U:
Example of Document Image
Filter set to 26U:
V - Blur Image
Smooths transitions by averaging the pixels next to the hard edges of
defined lines and shaded areas in an image.
0V
1V
Don’t blur (default)
Blur
Example of Blur Image Off (0
V):
Example of Blur Image On (1V):
8 - 14
4600rp, 4600g/4600r, 4800i User’s Guide
W - Histogram Ship
A histogram gives a quick picture of the tonal range of an image, or key type.
A low-key image has detail concentrated in the shadows; a high-key image
has detail concentrated in the highlights; and an average-key image has
detail concentrated in the midtones. This modifier ships the histogram for
an image.
0W Don’t ship histogram (default)
1W Ship histogram
Image used for histogram:
Histogram of image at left:
Image Size Compatibility
If you prefer that an image ship returns images at the sensor’s native resolution
(752x480 pixels for the 5X00 engine, 640x480 pixels for the 4X00 engine), scan
the Native Resolution code. If you have an 4X00 image engine and have
designed applications that expect an image ship to return exactly 640x480
pixels, scan the Force VGA Resolution bar code. Refer to "Show Engine
Revision" on page 11-1 for information on determining the engine in your unit.
Default = Force VGA Resolution
* Force VGA Resolution
Native Resolution
4600rp, 4600g/4600r, 4800i User’s Guide
8 - 15
Intelligent Signature Capture - IMGBOX
IMGBOX allows you to configure the size and location of a signature capture
area relative to its proximity to a barcode. This allows you to tailor a signature
capture area to a specific form. In order to use IMGBOX, you need a set form
where the signature box location is in a known location relative to a barcode. You
can input the overall size of the signature area, as well as specify how far the
signature area is from the barcode, vertically and horizontally. You can also set
the resolution and file format for the final output of the signature capture image.
Note: IMGBOX commands can only be triggered by one of the following types of
barcodes: PDF417, Code 39, Code 128, Aztec, Codabar, and Interleaved
2 of 5. Once one of these symbologies has been read, the image is
retained for a possible IMGBOX command.
The following IMGBOX example was executed and viewed using QuickView
Downloads. Select your device from the Products list, then select QuickView
Software Utility.
Below is an example of a signature capture application. In this example, the
aimer is centered over the signature capture area and the trigger is pressed. A
single beep is emitted, indicating that the imager has read a Code 128 barcode
and the data has been transferred to the host. An IMGBOX command may now
be sent from the host to specify the coordinates of the signature capture area
below that code, and indicating that only that area containing the signature
should be transferred as an image to the host.
To see this example, align the aimer with the signature area (not with the
barcode), then press the trigger.
Send the following IMGBOX command string after the button push:
IMGBOX245w37h55y.
Note: Case is not important in the command string. It is used here only for clarity.
The following image is captured:
8 - 16
4600rp, 4600g/4600r, 4800i User’s Guide
The IMGBOX commands have many different modifiers that can be used to
change the size and appearance of the signature image output by the imager.
Modifiers affect the image that is transmitted, but do not affect the image in
memory. Modifiers always begin with a number and end with a letter (case
insensitive). Any number of modifiers may be appended to the IMGBOX
command.
Note: The IMGBOX command will return a NAK unless a window size (width and
height) are specified. See H - Height of Signature Capture Area (page 8-
18) and W - Width of Signature Capture Area (page 8-19).
IMGBOX Modifiers
A - Output Image Width
This option is used to size the image horizontally. If using this option, set the
resolution (R) to zero.
Example of Image Width set to 200A:
Example of Image Width set to 600A:
B - Output Image Height
This option is used to size the image vertically. If using this option, set the
resolution (R) to zero.
Example of Image Height set to 50B:
Example of Image Height set to 100B:
D - Pixel Depth
This indicates the number of bits per pixel in the transmitted image, which
defines whether it will be grayscale or black and white.
8D
1D
8 bits per pixel, grayscale image (default)
1 bit per pixel, black and white image
4600rp, 4600g/4600r, 4800i User’s Guide
8 - 17
F - File Format
This option indicates the type of file format in which to save the image.
0F
1F
2F
3F
4F
5F
6F
7F
8F
KIM format
TIFF binary
TIFF binary group 4, compressed
TIFF grayscale
Uncompressed Binary
Uncompressed grayscale
JPEG image (default)
Outlined image
BMP format
H - Height of Signature Capture Area
The height of the signature capture area must be measured in inches
divided by .01. In the example, the height of the area to be captured is 3/8
inch, resulting in a value of H = .375/0.01 = 37.5.
Example: IMGBOX245w37h55y.
K - Gamma Correction
Gamma measures the brightness of midtone values produced by the image.
You can brighten or darken an image using gamma correction. A higher
gamma correction yields an overall brighter image. The lower the setting,
the darker the image. The optimal setting for text images is 50K.
0K
50K Apply gamma correction for brightening typical document image
nK Apply gamma correction factor n (n = 1-255)
Gamma correction off (default)
ExampleofGammaCorrection
set to 0K:
Example of Gamma Correction
set to 50K:
Example of Gamma Correction
set to 255K:
8 - 18
4600rp, 4600g/4600r, 4800i User’s Guide
R - Resolution of Signature Capture Area
The resolution is the number of pixels that the imager outputs per each
minimum bar width. The higher the value for R, the higher the quality of the
image, but also the larger the file size. Values begin at 1000. The imager
automatically inserts a decimal point between the first and second digit. For
example, use 2500 to specify a resolution of 2.5. Set to zero when using
the A and B modifiers (see A - Output Image Width and B - Output Image
Height on page 8-17).
Example of Resolution set to 0R:
Example of Resolution set to 1000R:
Example of Resolution set to 2000R:
S - Barcode Aspect Ratio
All dimensions used in IMGBOX are measured as multiples of the minimum
element size of the barcode. The barcode aspect ratio allows you to set the
ratio of the barcode height to the narrow element width. In the example, the
narrow element width is .010 inches and the barcode height is 0.400 inches,
resulting in a value of S = 0.4/0.01 = 40.
W - Width of Signature Capture Area
The width of the signature capture area must be measured in inches divided
by .01. In the example, the width of the area to be captured is 2.4 inches,
resulting in a value of W = 2.4/0.01 = 240. (A value of 245 was used in the
example to accommodate a slightly wider image area.)
Example: IMGBOX245w37h55y.
4600rp, 4600g/4600r, 4800i User’s Guide
8 - 19
X - Horizontal Barcode Offset
The horizontal barcode offset allows you to offset the horizontal center of the
signature capture area. Positive values move the horizontal center to the
right and negative values to the left. Measurements are in multiples of the
minimum bar width.
Example of Horizontal Offset set to 75X:
Example of Horizontal Offset set to -75X:
Y - Vertical Barcode Offset
The vertical barcode offset allows you to offset the vertical center of the
signature capture area. Negative numbers indicate that the signature
capture is above the barcode, and positive numbers indicate that the area is
below the barcode. Measurements are in multiples of the minimum bar
width.
Example of Vertical Offset set to -7Y:
Example of Vertical Offset set to 65Y:
8 - 20
4600rp, 4600g/4600r, 4800i User’s Guide
9
OCR Programming
Use this section to program the Imager for optical character recognition (OCR).
The 2D imager reads 6 to 60 point OCR typeface.
applications, create an OCR template to match the data, and print an
OCR check character.
The 2D imager will read OCR-A, OCR-B, U.S. Currency Serial Number (Money),
MICR E-13B, and SEMI Font.
You can either select an OCR default, or create your own custom template for
the type of OCR format you intend to read. See "OCR" on page 9-1 for
programming codes that will enable your imager to read OCR-A, OCR-B, U.S.
Currency, MICR E 13 B, or SEMI fonts. See "OCR Templates" on page 9-3 if
you want to create a custom “template,” or character string that defines the
length and content of OCR strings that will be read with your imager.
Note: Setting the template and check character options are essential for OCR
reading.
OCR Fonts
Default All OCR Settings turns off all OCR capability in the imager, so the
imager will be able to scan linear, stacked, matrix, and composite barcodes, but
not OCR fonts. In addition, any OCR templates you have created are erased.
The eight digit default templates are reinstated for any future use of the OCR On
codes listed below.
< Default All OCR Settings >
OCR
Note: OCR symbols can misread when scanned sideways or upside down. Use
Working Orientation, page 3-22, if your OCR symbols will not usually be
presented upright to the imager.
Only one OCR symbology can be read at a time.
OCR-A On allows you to scan characters in the OCR-A font. The default setting
template, character combinations that fit the template can be scanned (see
Creating an OCR Template, page 9-3).
OCR-A On
4600rp, 4600g/4600r, 4800i User’s Guide
9 - 1
OCR-B On allows you to scan characters in the OCR-B font. The default setting
allows you to scan any eight digit combination. If you have created an OCR
template, character combinations that fit the template can be scanned (see
Creating an OCR Template, page 9-3).
OCR-B On
U.S. Currency Font
U.S. Currency On allows you to scan characters in the font used on U.S.
currency. The default setting allows you to scan any eight digit combination. If
you have created an OCR template, character combinations that fit the template
can be scanned (see Creating an OCR Template, page 9-3).
U.S. Currency On
MICR E13 B Font
MICR E13 B On allows you to scan MICR characters on a bank check. The
default setting allows you to scan any eight digit combination. If you have
created an OCR template, character combinations that fit the template can be
scanned (see Creating an OCR Template, page 9-3).
MICR E 13 B On
Note: TOAD characters (Transit, On Us, Amount and Dash) are output in the
following manner:
the transit character is output as T
the amount character is output as A
the on us character is output as O
the dash character is output as D
9 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
SEMI Font
SEMI Font On allows you to scan the SEMI font used in the semiconductor
industry.
SEMI Font On
All OCR Off turns off all OCR capability in the imager, so the imager will be able
to scan linear, stacked, matrix, and composite barcodes, but not OCR fonts.
However, any OCR templates you have created will be retained in memory.
* All OCR Off
OCR Templates
You can create a custom “template,” or character string that defines the length
and content of OCR strings that will be read with your imager. There are several
choices when creating a custom template for your application. You can create a
template for a single format, you can string together several formats, and you can
create a template for a user-defined variable. These choices are described in
detail below.
Creating an OCR Template
A single template allows you to program the imager to read any combination of
characters in the order you specify. Refer to examples that follow the Template
Characters table below.
4600rp, 4600g/4600r, 4800i User’s Guide
9 - 3
Template Characters
a
c
d
e
g
h
i
represents any alphanumeric character (digit or letter)
represents that a check character is verified but not transmitted
represents any digit
represents any available OCR character
represents character from user-defined variable “g”
represents character from user-defined variable “h”
represents character from user-defined variable “g” or “h”
represents that a check character is verified but transmitted
represents any uppercase letter
k
l
t
marks the start of a new template
r
multi row indicator
All other characters represent themselves. Spaces can be used.
represent Transit, On Us, Amount, and Dash.
Note: OCR templates default to eight digits, no check character.
To Add an OCR Template
1. Turn on the OCR font you want to read (page 9-1).
2. Begin building the template.
Scan the Enter OCR Template symbol (page 9-13).
3. Scan the characters for the string.
Use the Template Characters chart above to determine what characters you
template.
Example: You need to read any combination of eight digits. The template would
be:
dddddddd
To create this template, you would enable the OCR-A font. Scan the Enter
OCR Template symbol (page 9-13), then scan the d from the OCR
Programming Chart in the back of this manual eight times. Scan Save OCR
Template (page 9-14). This would let you read any string of eight digits, for
example:
37680981
9 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
Character Match Sequences
On the ASCII Conversion Chart (Code Page 1252), page A-4, find the Hex
value that represents the character(s) you want to match. Use the
Programming Chart (inside the back cover) to scan the numbers that
represent these characters.
digits. The template would be:
ddd414243ddd
hex codes for
letters A, B, and C
To create this template, you would enable the OCR-A font. Scan the Enter
OCR Template symbol (page 9-13). Scan the d from the OCR Programming
Chart in the back of this manual three times. Then scan 414243 from the
inside back cover (the hex characters for “A,” “B,” and “C”), and scan the d
three more times. Scan Save OCR Template, page 9-14. This would let you
read any string of three digits, “ABC,” then any string of three digits, for
example:
551ABC983
Adding Spaces
You may also need to put spaces in your template.
hex code for a space
To create this template, you would enable the OCR-A font. Scan the Enter
OCR Template symbol (page 9-13). Scan the d from the OCR Programming
Chart in the back of this manual three times, then scan 2041424320 from the
Programming Chart on the inside back cover (the hex characters for “space,”
“A,” “B,” “C,” “space”). Scan the d three more times, then scan Save OCR
Template (page 9-14). This would let you read any string of three digits,
space, “ABC,” space, then any string of three digits. For example:
551 ABC 983
Note: If using Quick*View to program, use the space bar to designate a space
4. Exit OCR Template Editor
Scan Save OCR Template to save your entries. Discard OCR Template
exits without saving any OCR Template changes.
4600rp, 4600g/4600r, 4800i User’s Guide
9 - 5
Stringing Together Multiple Formats
(Creating “Or” Statements)
optical characters that match any one of the formats in the template.
Example: You need to read any combination of eight digits, or a combination of
be:
ddddddddtddddlldd
To create this template, you would enable the OCR-A font. Scan the Enter
OCR Template symbol (page 9-13). Scan the d from the OCR Programming
Chart in the back of this manual eight times, then scan the t to create the “or”
statement. Then you would scan the characters for the second template.
Scan d four times, scan l two times, then scan d two more times. Scan Save
OCR Template (page 9-14). This would let you read either type of format, for
example:
99028650
or
9902XZ50
You can string together as many templates as you need.
OCR User-Defined Variables
You can create up to two of your own user variables for an OCR template. These
variables will represent any OCR readable characters. The user-defined
variables are stored under the letters “g” and “h.” Creating a user variable follows
variable you specified.
Example: You need a variable to represent the letters “A,” “B,” or “C.” The
template for this variable would be:
414243
To create this template, you would enable the OCR-A font. Scan the Enter
User-Defined Variable g symbol (page 9-13). Scan 414243 from the
OCR Template (page 9-14). This will let you read either A or B or C in any
position where you place the g. For example, you could create the following
template:
ddddddggg
9 - 6
4600rp, 4600g/4600r, 4800i User’s Guide
This template would then let you read data that began with six digits, and had
an A, B, or C trailing. So you would be able to read:
654321ABC
or
654321BAC
or
654321CCC
Reading Multi-Row OCR
The imager is capable of decoding multi-row OCR text.
Note: Reading rows longer than sixteen characters is not recommended.
Consider the following example. This example shows serial commands as they
would be entered using Quick*View.
Example: You need to read multiple rows of OCR-A data as shown below:
12345678
ABCDEFGH
First, enable the OCR-A font. To read the first row of OCR data, you would
program the following template:
OCRTMP"dddddddd".
This template is the default OCR template. If you wanted to read the second
line of data, you would use the following template:
OCRTMP"llllllll".
To read both lines of OCR at one time, use the variable r to indicate the start
of a new row. All the other templating variables for the individual rows work
the same as previously described. For instance, in the above example, you
would use the following template to read both rows:
OCRTMP"ddddddddrllllllll".
To read the three rows below, you would use the template command
"OCRTMP"ddddddddrllllllllrlllldddd".
12345678
ABCDEFGH
ABCD1234.
4600rp, 4600g/4600r, 4800i User’s Guide
9 - 7
OCR Check Character
You may want to print and verify a check character in order to enhance the
security of your OCR application. The imager can be programmed for almost any
type of check character. A number of presets are provided for common check
character uses (e.g., modulo 10 and modulo 36).
Scan the OCR Modulo 10 or OCR Modulo 36 Check Character barcode to
specify the type of check character used in the OCR strings you’re scanning.
The imager will then only read OCR character strings with a valid check
You must specify the location of the check character in the template with a c.
Example: You need to read any combination of seven digits, with a modulo 10
check character in the eighth position. The template would be:
dddddddc
To create this template, you would enable the OCR-A font. Scan the Modulo
10 Check Character symbol. Then scan the Enter OCR Template symbol,
and scan the d from the OCR Programming Chart seven times, and scan the
c once. Scan Save OCR Template (page 9-14). This template will let you
read any combination of six digits with a correct check character after. (If the
check character is invalid, the data is discarded.) For example, the following
string could be scanned:
01234569
and the output would be: 0123456
OCR Modulo 10 Check Character
Scan this symbol to program the OCR template for a simple modulo 10
checksum of the digits 0 through 9.
OCR Modulo 10 Check Character
9 - 8
4600rp, 4600g/4600r, 4800i User’s Guide
OCR Modulo 36 Check Character
Scan this symbol to program the OCR template for a simple modulo 36
checksum of the digits 0 through 9 and the letters A through Z.
OCR Modulo 36 Check Character
OCR User-Defined Check Character
You can customize the check character calculation to suit your application. Each
character of the check character alphabet can be programmed in its proper
order. The number of characters you enter determines the modulo value for the
calculation. By default, the check character computation is unweighted, but the
imager also supports two weighted modulo 10 checking schemes.
Example: To program a modulo 11 check character, you would enter the
following 11 characters in order:
0123456789X
Also enter the OCR template:
dddddddc
Enable the OCR-A font, then scan the following string:
6512351X
The imager performs the following check character computation:
(6 + 5 + 1 + 2 +3 + 5 + 1 + X) modulo 11 = 0
Since the result is zero, the message is considered to be valid, so the reader
outputs the message: 6512351
Programming a User-Defined Check Character
1. Scan the Enter OCR Check Character barcode, below.
Enter OCR Check Character
4600rp, 4600g/4600r, 4800i User’s Guide
9 - 9
2. Enter the characters in order. For each character, look up the corresponding
hex value from the ASCII Conversion Chart (Code Page 1252), page A-4.
Use the Programming Chart on the inside the back cover of this manual to
scan the two symbols for each hex value.
3. Scan the Save barcode on the inside back cover.
Example: To program the modulo 11 check character from example #8 on
page 9-9, enable the OCR-A font. Scan the Enter OCR Check
Character barcode on page 9-9, then scan the following hex values
in order:
3031323334353637383958
After you enter all the desired hex values, scan the Save barcode on the
inside back cover of this manual.
Weighting Options
By default, the check character computation is unweighted. It is possible to use
one of two weighted modulo 10 schemes. Weighting is often used to detect if
two neighboring characters are transposed, a common error when an operator
keys in data.
3-1-3-1 Weighted Modulo 10 Check Character
Starting with the check character and working backward through the message,
the imager applies a multiplier of 1, then 3, then 1, then 3, and so on. This is the
checking scheme used in many EAN•UCC symbologies, including U.P.C. and
Interleaved 2 of 5 (when a check digit is invoked). To apply this weighting
scheme, set the OCR check character to “0123456789x3x1” or scan the
following symbol:
3-1-3-1 Weighted Modulo 10
Check Character
Example: Scan the 3-1-3-1 Weighted Modulo 10 Check Character symbol. Also
enter the OCR template:
dddddddc
Then scan the string below:
01234565
The reader performs the check character computation below:
(0 x 3 + 1 x 1 + 2 x 3 + 3 x 1 + 4 x 3 + 5 x 1 + 6 x 3 + 5 x 1) modulo 10 = 0
9 - 10
4600rp, 4600g/4600r, 4800i User’s Guide
Since the result is zero, the message is considered to be valid, so the reader
outputs the message: 0123456
2-1-2-1 Weighted Modulo 10 Check Character
Starting with the check character and working backward through the message,
the imager applies a multiplier of 1, then 2, then 1, then 2, and so on. When the
result of the multiplication is greater than 9, add both digits to the running sum.
This is often referred to as the LUHN formula. One common application of the
LUHN formula is validate credit card numbers. This is the modulo 10 checking
scheme used in MSI Code and in Code 32 Pharmaceutical (PARAF). To apply
this weighting scheme, set the OCR check character to "0123456789x2x1" or
scan the following symbol:
2-1-2-1 Weighted Modulo 10
Check Character
Example: Scan the 2-1-2-1 Weighted Modulo 10 Check Character symbol. Also
enter the OCR template:
ddddddc
Then scan the string below:
0128454
The reader performs the check character computation below:
(0 x 1 + 1 x 2 + 2 x 1 + 8 x 2 + 4 x 1 + 5 x 2 + 4 x 1) modulo 10
= (0 + 2 + 2 + (1 + 6) + 4 + (1 + 0) + 4) modulo 10
= 0
Since the result is zero, the message is considered to be valid, so the reader
outputs the message: 012845
4600rp, 4600g/4600r, 4800i User’s Guide
9 - 11
OCR ISBN Application Example
One application of OCR is to read the ISBN characters typically encoded using
the OCR-A or OCR-B font. This is especially useful when the ISBN number is
not encoded in an EAN-13 barcode. The following example shows how to
configure the imager to read the ISBN strings on books in Japan. After you have
followed the steps below, you will be able to scan the following ISBN number or
the additional data below it, depending on the line of text at which the imager is
aimed.
1. Scan the OCR-B On barcode on page 9-2.
2. Program the user-defined variable “g” to comprise the ten digits plus the
dash:
0123456789-
3. In Japan, it is common for two fields to follow the ISBN number, the three
digit price field, and the four digit price field. The first field typically starts with
a “C” (uppercase c), followed by four digits. The second field typically starts
with a “P” or a yen symbol, followed by three or four digits, followed by an
“E.” Program the user-defined variable “h” to comprise the “P” and the yen
symbol (represented by a backslash).
P\
4. Scan the symbol below to set up three templates to handle the ISBN
number, the three digit price field, and the four digit price field.
9 - 12
4600rp, 4600g/4600r, 4800i User’s Guide
5. Finally, set up the ISBN check digit, which is a special position-weighted
modulo 11 checksum. The imager automatically invokes the ISBN
checksum for template rows that are:
1.) at least fourteen characters long,
2.) whose first four characters are the letters “ISBN,”
3.) whose last character is a check character, and
4.) when the modulo 11 check character “0123456789X” is programmed.
Please note that all these commands can be combined into a single serial
programming command:
OCRENA2,TMP”ISBNggggggggggggctCdddd hdddEtCdddd
hddddE”,GPG”0123456789-”,GPH”P\”,CHK”0123456789X”.
These commands can be encoded into the following Aztec Code symbol:
OCR Template Codes
Note: Reading more than three rows of OCR is not recommended. Contact the
factory if you have an application that requires reading four or more rows
of OCR.
Enter OCR Template †
Enter User-Defined
Variable “g”†
Enter User-Defined
Variable “h”†
† One or more two-digit numbers and Save are required after reading this
cover of this manual.
4600rp, 4600g/4600r, 4800i User’s Guide
9 - 13
10
Interface Keys
Keyboard Function Relationships
The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII
“CTRL”+ relationships apply to all terminals that can be used with the imager.
Refer to page 2-8 enable Control + ASCII mode.
Function Code
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HEX/ASCII Value
Full ASCII “CTRL” +
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
@
A
B
C
D
E
F
G
H
I
HT
LF
J
VT
K
L
FF
CR
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
\
GS
]
RS
^
US
_
4600rp, 4600g/4600r, 4800i User’s Guide
10 - 1
The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to US
only. The following chart indicates the equivalents of these five characters for
different countries.
Country
United States
Belgium
Codes
[
[
\
<
<
8
Ã
\
]
]
6
6
6
6
6
6
6
6
6
6
6
-
-
Scandinavia
France
8
^
9
$
+
+
. .
]
-
=
-
Germany
Italy
-
Switzerland
United Kingdom
Denmark
Norway
<
¢
\
-
[
8
8
[
-
9
9
]
-
\
-
Spain
\
-
10 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
Supported Interface Keys
IBM AT/XT and
PS/2 Compatibles,
WYSE PC/AT
IBM XTs and
Compatibles
IBM, DDC, Memorex
Telex, Harris*
ASCII
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
HEX
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
Supported Keys
Reserved
Enter (KP)
Cap Lock
ALT make
ALT break
CTRL make
CTRL break
CR/Enter
Reserved
Tab
Reserved
Tab
Delete
CR/Enter
Insert
Supported Keys Supported Keys
Reserved
CR/Enter
Caps Lock
Reserved
Reserved
Reserved
Reserved
CR/Enter
Reserved
Tab
Reserved
Enter
F11
F12
F13
F14
F15
New Line
F16
F17
Reserved
Tab
F18
Tab/Field Forward
Delete
CR/Enter
Insert
Delete
Field Exit/New Line
Insert
Escape
F11
Home
Escape
Reserved
Home
F19
Error Reset
Home
Print
Print
F20
Back Space
Back Tab
F12
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
Back Space
Back Tab
Reserved
F1
F2
F3
F4
F5
F6
Back Space
Backfield/Back Tab
F21
F1
F2
F3
F4
F5
F6
F8
F9
F10
F8
F9
F10
US
* IBM 3191/92, 3471/72, 3196/97, 3476/77, Telex (all models)
4600rp, 4600g/4600r, 4800i User’s Guide
10 - 3
Supported Interface Keys
IBM, Memorex Telex (102)* Memorex Telex (88)**
ASCII
HEX
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
Supported Keys
Supported Keys
Reserved
Enter
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
Reserved
Enter
F11
PF10
F12
PF11
F13
PF12
F14
F15
New Line
F16
F17
Reserved
Reserved
New Line
Field Forward
Field Forward
Reserved
Field Forward
Delete
New Line
Insert
Erase
Error Reset
Reserved
Print
F18
Tab/Field Forward
Delete
Field Exit
Insert
Clear
Error Reset
Home
Print
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
Back Space
Back Tab
F19
Back Space
Back Field
Reserved
PF1
F1
F2
PF2
F3
PF3
F4
PF4
F5
PF5
F6
PF6
F7
PF7
F8
PF8
F9
PF9
US
F10
Home
* IBM 3196/97, 3476/77, 3191/92, 3471/72, Memorex Telex (all models) with 102
key keyboards
** Memorex Telex with 88 key keyboards
10 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
Supported Interface Keys
Esprit 200, 400
ANSI
Esprit 200, 400
ASCII
Esprit 200, 400
PC
ASCII
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
HEX
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
Supported Keys
Reserved
New Line
N/A
N/A
N/A
N/A
N/A
New Line
N/A
Tab
N/A
Tab
N/A
New Line
N/A
Escape
F11
Insert
F13
Back Space
Back Tab
F12
Supported Keys
Supported Keys
Reserved
New Line
N/A
N/A
N/A
N/A
N/A
New Line
N/A
Tab
N/A
Tab
N/A
New Line
N/A
Escape
F11
Insert
F13
Back Space
Back Tab
F12
Reserved
New Line
N/A
N/A
N/A
N/A
N/A
New Line
N/A
Tab
N/A
Tab
Delete
New Line
Insert
Escape
F11
Home
Print
Back Space
Back Tab
F12
F1
F2
F3
F4
F5
F6
F7
F1
F2
F3
F4
F5
F6
F7
F8
F1
F2
F3
F4
F5
F6
F7
F9
F10
F9
F10
F9
F10
US
4600rp, 4600g/4600r, 4800i User’s Guide
10 - 5
Supported Interface Keys
Apple Mac/iMac
ASCII
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
HEX
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
7F
Supported Keys
Reserved
Enter/Numpad Enter
CAPS
ALT make
ALT break
CNTRL make
CNTRL break
RETURN
APPLE make
TAB
APPLE break
TAB
Del
RETURN
Ins Help
ESC
F11
Home
Prnt Scrn
BACKSPACE
LSHIFT TAB
F12
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
BACKSPACE
US
DEL
10 - 6
4600rp, 4600g/4600r, 4800i User’s Guide
11
Utilities
To Add a Test Code I.D. Prefix to All Symbologies
This selection allows you to turn on transmission of a Code I.D. before the
decoded symbology. (See the Symbology Chart, included in the Appendix
A, page A-1) for the single character code that identifies each symbology.) This
action first clears all current prefixes, then programs a Code I.D. prefix for all
symbologies. This is a temporary setting that will be removed when the unit is
power cycled.
Add Code I.D. Prefix to
Show Decoder Revision
Scan the barcode below to output the decoder revision.
Note: You may use the Show Decoder Revision option if you have firmware with
a base number of 31205480. Refer to Show Software Revision on page
11-2 for information on determining the firmware revision in your unit.
Show Decoder Revision
Show Engine Revision
Note: You may use the Show Engine Revision option if you have firmware with
a base number of 31205480.
Scan the barcode below to output the engine revision. If your imager has an
4X00 engine, it will return an [ACK] with no data in the string. If your imager has
an 5X00 engine, it will return the engine type, revision number, and status
character [ACK]. For example, an imager with an 5100, version 26 would return:
ENGREVType: 1 Revision: 26[ACK]
Show Engine Revision
4600rp, 4600g/4600r, 4800i User’s Guide
11 - 1
Show Scan Driver Revision
Scan the barcode below to output the scan driver revision. The scan driver
controls image capture.
You may use the Show Scan Driver Revision option if you have firmware with a
base number of 31205480. Refer to the Show Software Revision below for
information on determining the firmware revision in your unit.
Show Scan Driver Revision
Show Software Revision
Scan the barcode below to output the current software revision, unit serial
number, and other product information.
Show Software Revision
Show Data Format
Scan the barcode below to show current data format settings.
Data Format Settings
Resetting the Standard Product Defaults
If you aren’t sure what programming options are in your imager, or you’ve
changed some options and want the standard product default settings restored,
scan the Standard Product Default Settings barcode below.
Standard Product Default Settings
The Menu Commands starting on page 12-5 lists the standard product default
settings for each of the commands (indicated by an asterisk (*) on the
programming pages).
11 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
Test Menu
When you scan the Test Menu On code, then scan a programming code in this
manual, the imager displays the content of a programming code. The
programming function will still occur, but in addition, the content of that
programming code is output to the terminal.
Note: This feature should not be used during normal imager operation.
On
* Off
2D PQA (Print Quality Assessment)
Two-dimensional Print Quality Assessment (2D PQA) is a feature of Hand Held
Products’ image readers where the data from the successful read of a 2D
barcode symbol is augmented with lines of text that both identify the symbol, and
also report graded measurement parameters obtained from it.
2D PQA Reporting
Hand Held Products' 2D PQA reporting can be enabled in two different modes:
Full Report or Screening. (To see displayed results, Microsoft® Notepad, a
word processor/editing program, or Quick*View (page 11-6) is recommended.)
If you are using Quick*View, you can enable Full Report, a listing of all of a sym-
bol's identifying information, measurements, and corresponding grades, by typ-
ing the following menu command:
2D_PQA1
or by scanning the following barcode:
Full Report
4600rp, 4600g/4600r, 4800i User’s Guide
11 - 3
Note: The PQA report is sent out as a second data/beep sequence after the
barcode data. The report has its own Hand Held Products code ID of
>(0X3E) so it can be uniquely identified.
You can exit Full Report mode by either typing the menu command, 2D_PQA0,
if you are using Quick*View, or by scanning the following barcode:
Exit
Note: For additional information on interpreting your read results, please refer
to Hand Held Products Quick Check 2D Print Assessment User’s Guide.
Visual Xpress Introduction
Note: Software revision 31205480-118 (or newer) with support for light bar off-
axis illumination is backward compatible with all non-light bar units. This
new revision of software can be flashed in non-light bar units for full
backward compatibility. Non-light bar Software 31205480-090 (or older)
cannot be flashed into units with a light bar. Visual Xpress will display an
incompatibility error message. Refer to the Show Software Revision on
page 11-2 for information on determining the software in your unit.
Visual Xpress provides a wide range of PC-based programming functions that
can be performed on an imager connected to your PC's COM port. Visual Xpress
allows you to download upgrades to the imager's firmware, change programmed
parameters, and create and print programming barcodes. Using Visual Xpress,
you can even save/open the programming parameters for an imager. This saved
file can be e-mailed or, if required, you can create a single barcode that contains
all the customized programming parameters and mail or fax that barcode to any
location. Users in other locations can scan the barcode to load in the customized
programming.
To communicate with an imager, Visual Xpress requires that the PC have at least
one available serial communication port, or a serial port emulation using a
physical USB port. If you are using the serial port and RS-232 cable, an external
power supply is required. When using a USB serial port emulation, only a USB
cable is required.
Visual Xpress Operations
The Visual Xpress software performs the following operations:
Scan Data
Scan Data allows you to scan barcodes and display the barcode data in a
window. Scan Data lets you send serial commands to the imager and receive
imager response that can be seen in the Scan Data window. The data displayed
in the Scan Data window can either be saved in a file or printed.
11 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
Configure
Configure displays the programming and configuration data of the imager. The
imager's programming and configuration data is grouped into different
categories. Each category is displayed as a tree item under the "Configure" tree
node in the application explorer. When one of these tree nodes is clicked, the
right-hand side is loaded with the parameters' form belonging to that particular
category. The "Configure" tree option has all the programming and configuration
parameters specified for an imager. You can set or modify these parameters as
required. You can later write the modified settings to the imager, or save them
to a dcf file.
Imaging
Imaging provides all the image-related functions that a 2D Imager can perform.
You can capture an image using the current settings, and the image will be
displayed in an image window. Images captured from the imager can be saved
to files in different image formats. You can modify the image settings and save
the image settings to an INI file, which can be loaded later to capture new
images. Imaging also lets you preview the images continuously captured by the
imager.
Installing Visual Xpress from the Web
Note: Visual Xpress requires .NET software. If .NET is not installed on your PC,
you will be prompted to install it during the Visual Xpress installation.
2. Click in the Quick Search text box and enter Visual Xpress.
3. Click on Search Now.
4. Click on the entry for Visual Xpress.
5. When prompted, select Save File, and save the files to the
c:\windows\temp directory.
6. Once you have finished downloading the file, exit the web site.
7. Using Explorer, go to the c:\windows\temp file and unzip the file you saved.
8. Double click on Setup.exe and follow the screen prompts to install the Visual
Xpress program.
9. If you’ve selected the defaults during installation, you can click on Start
Menu-Programs-Hand Held Products-Visual Xpress.
4600rp, 4600g/4600r, 4800i User’s Guide
11 - 5
Quick*View
®
Quick*View is a Microsoft Windows program that displays decoded symbol
messages and captures images (for instance, ID photographs) from the imager.
Barcode information and images are displayed in the Quick*View window.
Installing Quick*View from the Web
2. Click on Search and enter Quick*View.
3. Click on Search.
4. Click on the entry for Software. Select Quick*View Software Utility.
5. When prompted, select Save, and save the files to the c:\windows\temp
directory.
6. Once you have finished downloading the file, exit the web site.
7. Using Explorer, go to the c:\windows\temp file.
8. Double click on the Quickview.exe file. Follow the screen prompts to install
the Quick*View program.
9. To start Quick*View, from the Start Menu click on Programs, Quick*View,
Quick*View.
Note: If you wish, you can create a shortcut to the Quick*View executable on
your desktop.
Temporary Quick*View Configuration
For a quick download communication configuration, scan the Quick*View
barcode and the imager will be temporarily configured for Quick*View settings.
Note: If you have a unit capable of keyboard wedge mode, scan the barcode
below and the unit will communicate in RS-232 mode, allowing it to work
with Quick*View. To convert the imager back to keyboard wedge
communication, cycle the power.
Quick*View
11 - 6
4600rp, 4600g/4600r, 4800i User’s Guide
12
Serial Programming Commands
The serial programming commands can be used in place of the programming
barcodes. Both the serial commands and the programming barcodes will
program your imager. For complete descriptions and examples of each serial
programming command, refer to the corresponding programming barcode in this
manual.
The device must be set to an RS-232 interface (see page 1-11). The following
commands can be sent via a PC COM port using terminal emulation software.
Conventions
The following conventions are used for menu and query command descriptions:
parameterA label representing the actual value you should send as part of a
command.
[option] An optional part of a command.
{Data} Alternatives in a command.
bold
Names of menus, menu commands, buttons, dialog boxes, and
windows that appear on the screen.
Menu Command Syntax
Menu commands have the following syntax (spaces have been used for clarity
only):
Prefix Tag SubTag {Data} [, SubTag {Data}] [; Tag SubTag {Data}] […] Storage
Prefix
Tag
Three ASCII characters: SYN M CR (ASCII 22,77,13).
A 3 character case-insensitive field that identifies the desired menu
command group. For example, all RS-232 configuration settings
are identified with a Tag of 232.
SubTag
A 3 character case-insensitive field that identifies the desired menu
command within the tag group. For example, the SubTag for the
RS-232 baud rate is BAD.
Data
The new value for a menu setting, identified by the Tag and Sub-
Tag.
Storage
A single character that specifies the storage table to which the
mand’s operation on the device’s volatile menu configuration table.
A period (.) performs the command’s operation on the device’s
non-volatile menu configuration table. Use the non-volatile table
only for semi-permanent changes you want saved through a power
cycle.
4600rp, 4600g/4600r, 4800i User’s Guide
12 - 1
Query Commands
Several special characters can be used to query the device about its settings.
^
?
*
What is the default value for the setting(s).
What is the device’s current value for the setting(s).
What is the range of possible values for the setting(s). (The de-
vice’s response uses a dash (-) to indicate a continuous range of
values. A pipe (|) separates items in a list of non-continuous val-
ues.)
Tag Field Usage
When a query is used in place of a Tag field, the query applies to the entire set
of commands available for the particular storage table indicated by the Storage
field of the command. In this case, the SubTag and Data fields should not be
used because they are ignored by the device.
SubTag Field Usage
When a query is used in place of a SubTag field, the query applies only to the
subset of commands available that match the Tag field. In this case, the Data
field should not be used because it is ignored by the device.
Data Field Usage
When a query is used in place of the Data field, the query applies only to the
specific command identified by the Tag and SubTag fields.
Concatenation of Multiple Commands
Multiple commands can be issued within one Prefix/Storage sequence. Only the
Tag, SubTag, and Data fields must be repeated for each command in the
sequence. If additional commands are to be applied to the same Tag, then the
new command sequence is separated with a comma (,) and only the SubTag and
Data fields of the additional command are issued. If the additional command
requires a different Tag field, the command is separated from previous
commands by a semicolon (;).
Responses
The device responds to serial commands with one of three responses:
ACK Indicates a good command which has been processed.
ENQ Indicates an invalid Tag or SubTag command.
NAK Indicates the command was good, but the Data field entry was out of the
allowable range for this Tag and SubTag combination, e.g., an entry for a
minimum message length of 100 when the field will only accept 2
characters.
12 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
When responding, the device echoes back the command sequence with the
status character inserted directly before each of the punctuation marks (the
period, exclamation point, comma, or semicolon) in the command.
Examples of Query Commands
In the following examples, a bracketed notation [ ] depicts a non-displayable
response.
Example #1:What is the range of possible values for Codabar Coding Enable?
Enter:
cbrena*.
Response: CBRENA0-1[ACK]
This response indicates that Codabar Coding Enable (CBRENA) has a range of
values from 0 to 1 (off and on).
Example #2: What is the default value for Codabar Coding Enable?
Enter:
cbrena^.
Response: CBRENA1[ACK]
This response indicates that the default setting for Codabar Coding Enable
(CBRENA) is 1, or on.
Example #3: What is the device’s current setting for Codabar Coding Enable?
Enter:
cbrena?.
Response: CBRENA1[ACK]
This response indicates that the device’s Codabar Coding Enable (CBRENA) is
set to 1, or on.
Example #4: What are the device’s settings for all Codabar selections?
Enter:
cbr?.
Response: CBRENA1[ACK],
SSX0[ACK],
CK20[ACK],
CCT1[ACK],
MIN2[ACK],
MAX60[ACK],
DFT[ACK].
This response indicates that the device’s Codabar Coding Enable (CBRENA) is
set to 1, or on;
the Start/Stop Character (SSX) is set to 0, or Don’t Transmit;
concatenation (CCT) is set to 1, or Enabled;
the Minimum Message Length (MIN) is set to 2 characters;
the Maximum Message Length (MAX) is set to 60 characters;
and the Default setting (DFT) has no value.
4600rp, 4600g/4600r, 4800i User’s Guide
12 - 3
Trigger Commands
You can activate and deactivate the imager with serial trigger commands. First,
the imager must be put in Manual/Serial Trigger Mode either by scanning the
Serial Menu Command (page 12-9). Once the imager is in serial trigger mode,
the trigger is activated and deactivated by sending the following commands:
Activate: SYN T CR
Deactivate: SYN U CR
The imager scans until a barcode has been read, until the deactivate command
is sent, or until the serial time-out has been reached (see "Read Time-Out" on
page 3-4 for a description, and the serial command on page 12-9).
Resetting the Standard Product Defaults
If you aren’t sure what programming options are in your imager, or you’ve
changed some options and want the factory settings restored, scan the
Standard Product Default Settings barcode below.
Standard Product Default Settings
The chart on the following pages lists the factory default settings for each of the
menu commands (indicated by an asterisk (*) on the programming pages).
12 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
Menu Commands
Note: Not all menu commands apply to all imager models.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Factory Default Settings
Default
DEFALT
12-4
Terminal Interfaces
000 (4600g/4600r/4600rp/
4800i 030 models)
124 (4600g/4600r/4600rp/
4800i 050 models)
2-1
Terminal ID
TERMID###
4600rp, 4600g/4600r, 4800i User’s Guide
12 - 5
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
*U.S.A.
KBDCTY0
KBDCTY1
KBDCTY16
KBDCTY18
KBDCTY15
KBDCTY8
KBDCTY2
KBDCTY3
KBDCTY4
KBDCTY17
KBDCTY19
KBDCTY12
KBDCTY5
KBDCTY14
KBDCTY11
KBDCTY9
KBDCTY20
KBDCTY13
KBDCTY25
KBDCTY26
KBDCTY21
KBDCTY22
KBDCTY10
KBDCTY23
KBDCTY6
KBDCTY27
KBDCTY24
KBDCTY7
KBDSTY0
KBDSTY1
KBDSTY2
KBDSTY6
2-4
2-4
2-4
2-4
2-4
2-4
2-4
2-4
2-4
2-4
2-4
2-4
2-5
2-5
2-5
2-5
2-5
2-5
2-5
2-5
2-5
2-5
2-5
2-5
2-5
2-6
2-6
2-6
2-6
2-6
2-7
2-7
Belgium
Brazil
Canada (French)
Czech Republic
Denmark
Finland (Sweden)
France
Germany/Austria
Greece
Hungary
Israel (Hebrew)
Italy
Latin America
Netherlands (Dutch)
Norway
Program Keyboard
Country
Poland
Portugal
Romania
Russia
SCS
Slovakia
Spain
Sweden
Switzerland (German)
Turkey F
Turkey Q
U.K.
*Regular
Caps Lock
Shift Lock
Automatic Caps Lock
Keyboard Style
Emulate External
Keyboard
KBDSTY5
2-7
12 - 6
4600rp, 4600g/4600r, 4800i User’s Guide
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
*Control + ASCII Off
KBDCAS0
KBDCAS1
2-8
2-8
DOS Mode Control + ASCII
Windows Mode Control +
ASCII
KBDCAS2
2-8
*Turbo Mode Off
Turbo Mode On
*Numeric Keypad Off
Numeric Keypad On
*Auto Direct Conn. Off
Auto Direct Conn. On
300 BPS
KBDTMD0
KBDTMD1
KBDNPS0
KBDNPS1
KBDADC0
KBDADC1
232BAD0
232BAD1
232BAD2
232BAD3
232BAD4
232BAD5
232BAD6
232BAD7
232BAD8
232BAD9
2-8
Keyboard Modifiers
2-8
2-8
2-8
2-9
2-9
2-10
2-10
2-10
2-10
2-10
2-10
2-10
2-10
2-10
2-10
600 BPS
1200 BPS
2400 BPS
4800 BPS
Baud Rate
9600 BPS
19200 BPS
*38400 BPS
57600 BPS
115200 BPS
7 Data, 1 Stop, Parity Even
2-11
232WRD3
7 Data, 1 Stop, Parity None
7 Data, 1 Stop, Parity Odd
7 Data, 2 Stop, Parity Even
7 Data, 2 Stop, Parity None
7 Data, 2 Stop, Parity Odd
8 Data, 1 Stop, Parity Even
*8 Data, 1 Stop, Parity None
8 Data, 1 Stop, Parity Odd
232WRD0
232WRD6
232WRD4
232WRD1
232WRD7
232WRD5
232WRD2
232WRD8
2-11
2-11
2-11
2-11
2-11
2-11
2-11
2-11
Word Length: Data Bits,
Stop Bits, and Parity
RS-232 Receiver Time-
out
Range 0 - 300 seconds
232LPT###
2-12
4600rp, 4600g/4600r, 4800i User’s Guide
12 - 7
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
*RTS/CTS Off
232CTS0
2-12
2-12
2-12
2-12
2-12
2-12
2-13
2-13
2-14
2-14
2-14
2-14
2-14
2-14
2-14
2-14
2-15
2-15
2-15
2-15
2-15
2-15
2-15
2-15
2-15
2-16
2-16
2-16
2-16
RTS/CTS On
232CTS1
*XON/XOFF Off
232XON0
232XON1
232ACK0
RS-232 Handshaking
XON/XOFF On
*ACK/NAK Off
ACK/NAK On
232ACK1
Same Code Format
TERMID64
TERMID61
WNDBLK0
WNDBLK1
WNDBLK2
WNDBLK3
WNDDLY0
WNDDLY1
WNDDLY2
WNDDLY3
WNDCHK1
WNDCHK0
WNDSPD0
WNDSPD1
WNDSPD2
WNDSPD3
WNDSPD4
WNDSPD5
WNDSPD6
WNDPOL0
WNDPOL1
WNDIDL0
WNDIDL1
Wand Emulation Connec-
tion
Code 39 Format
20
*40
Data Block Size
60
80
5ms
*50ms
150ms
500ms
On
Delay Between Blocks
Overall Checksum
*Off
10
*25
40
Wand Emulation Trans-
mission Rate
80
120
150
200
*Black High
White High
Idle Low
*Idle High
Wand Emulation Polarity
Wand Emulation Idle
Output Selections
Beeper - Good Read
Off
BEPBEP0
BEPBEP1
3-1
3-1
*On
12 - 8
4600rp, 4600g/4600r, 4800i User’s Guide
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Off
BEPLVL0
BEPLVL1
3-1
3-1
Low
Beeper Volume - Good
Read
*Medium (default for 4600g/
4600r/4600rp)
BEPLVL2
3-1
*High (default for 4800i)
Low (1600) (min 400Hz)
*Medium (3250)
High (4200) (max 9000Hz)
*Normal Beep
Short Beep
BEPLVL3
3-1
3-2
3-2
3-2
3-2
3-2
3-2
3-2
3-3
3-3
3-3
3-3
3-3
3-3
BEPFQ11600
BEPFQ13250
BEPFQ14200
BEPBIP0
Beeper Pitch - Good
Read (Frequency)
Beeper Duration - Good
Read
BEPBIP1
Off
BEPLED0
LED - Good Read
*On
BEPLED1
*1
BEPRPT1
Number of Beeps - Good
Read
Range 1 - 9
BEPRPT#
*No Delay
DLYGRD0
Short Delay (500 ms)
Medium Delay (1000 ms)
Long Delay (1500 ms)
DLYGRD500
DLYGRD1000
DLYGRD1500
Good Read Delay
User-Specified Good
Read Delay
Range 0 - 30,000 ms
DLYGRD#####
TRGMOD0
3-3
3-4
3-4
*Manual/Serial Trigger Mode
Manual/Serial Trigger
Read Time-Out
(0 - 300,000 ms) *30,000
TRGSTO####
Manual Trigger, Low Power
Mode
TRGMOD2
3-4
3-5
Manual Trigger, Low
Power
Low Power Time-Out Timer
( 0 - 300 seconds) *120
TRGLPT###
*Off
TRGSSW0
TRGSSW1
TRGMOD4
3-5
3-5
3-6
3-6
3-6
3-7
3-7
3-7
In-Stand Sensor Mode
On
Scan Stand Mode
Presentation Mode
LEDs Off
Scan Stand
Presentation
TRGMOD3
TRGPCK0
TRGPCK1
TRGPMS##
Presentation LED Timer
Presentation Sensitivity
*LEDs On
Range 0-20 (*1)
4600rp, 4600g/4600r, 4800i User’s Guide
12 - 9
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Streaming Presentation
Hands Free Time-Out
Streaming Presentation Mode
Range 0 - 300,000 ms
Short (500 ms)
TRGMOD8
3-7
3-8
3-8
3-8
3-8
3-8
TRGPTO######
DLYRRD500
DLYRR750
*Medium (750 ms)
Reread Delay
Long (1000 ms)
DLYRRD1000
DLYRRD2000
Extra Long (2000 ms)
User-Specified Reread
Delay
Range 0 - 30,000 ms
DLYRRD#####
3-9
Off
PWRLDC0
PWRLDC50
PWRLDC100
SCNLED1
3-9
LED Power Level
Low (50%)
*High (100%)
*Lights On
Lights Off
3-9
3-9
3-10
3-10
Illumination Lights
Imager Time-Out
SCNLED0
Range 0 - 999,999 ms
(*60,000 ms)
SDRTIM######
3-9
200 milliseconds
400 milliseconds
*Off (no delay)
SCNDLY200
SCNDLY400
SCNDLY0
3-10
3-10
3-10
Aimer Delay
User-Specified Aimer
Delay
Range 0 - 4,000 ms
SCNDLY####
3-11
Off
SCNAIM0
SCNAIM1
SCNAIM2
DECWIN1
DECWIN0
3-11
3-11
3-11
3-13
3-13
Aimer Mode
Concurrent (4X00 default)
Interlaced (5X00 default)
Centering On
*Centering Off
Left of Centering Window
(*40%)
DECLFT
DECRGT
DECTOP
DECBOT
3-13
3-13
3-13
3-13
Right of Centering Window
(*60%)
Centering Window
Top of Centering Window
(*40%)
Bottom of Centering Window
(*60%)
12 - 10
4600rp, 4600g/4600r, 4800i User’s Guide
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Full Omnidirectional
(Default for 2D imagers)
DECMOD0
DECMOD1
DECMOD2
3-14
3-14
3-14
Decode Search Mode
Quick Omnidirectional
Advanced Linear Decoding
(Default for PDF imagers)
On
PRFENA1
PRFENA0
PRFCOD##
PRFBLK##
PRFPTO####
PRFDFT
3-15
3-15
3-15
3-15
3-16
3-16
3-19
3-19
3-19
3-19
3-19
3-20
3-20
3-20
3-20
3-21
3-21
3-21
3-21
3-22
3-22
3-22
*Off
High Priority Symbology
Preferred Symbology
Low Priority Symbology
Preferred Symbology Timeout
Preferred Symbology Default
Enter Sequence
SEQBLK
Output Sequence Editor
Default Sequence
SEQDFT
Required
SEQ_EN2
SEQ_EN1
SEQ_EN0
SHOTGN1
SHOTGN0
SHWNRD1
SHWNRD0
PRTWGT
PRTWGT4
VIDREV1
VIDREV0
ROTATN0
ROTATN1
ROTATN2
Require Output
Sequence
On/Not Required
*Off
On
Multiple Symbols
No Read
*Off
On
*Off
Set Print Weight (1-7)
Print Weight
Video Reverse
*Default (4)
On
*Off
*Upright
Rotate Code Clockwise 90°
Upside Down
Working Orientation
Rotate Code
Counterclockwise 90°
ROTATN3
3-22
Prefix/Suffix Selections
Add CR Suffix to All Symbologies
VSUFCR
PREBK2##
PRECL2
PRECA2
4-3
4-4
4-4
4-4
Add Prefix
Prefix
Clear One Prefix
Clear All Prefixes
4600rp, 4600g/4600r, 4800i User’s Guide
12 - 11
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Add Suffix
SUFBK2##
SUFCL2
4-4
4-4
4-4
4-4
4-4
4-5
Suffix
Clear One Suffix
Clear All Suffixes
*Enable
SUFCA2
RMVFNC0
RMVFNC1
DLYCHR##
Function Code Transmit
Intercharacter Delay
Disable
Range 0 - 495 ms
Delay Length
(0 - 495 ms)
DLYCRX##
4-6
User Specified
Intercharacter Delay
Character to Trigger Delay
Range 0 - 495 ms
DLY_XX###
DLYFNC##
DLYMSG##
4-6
4-6
4-7
Interfunction Delay
Intermessage Delay
Range 0 - 495 ms
Data Formatter Selections
*Default Data Format (None)
DFMDF3
DFMBK3##
DFMCL3
DFMCA3
DFM_EN0
DFM_EN1
DFM_EN2
VSAF_1
5-5
5-5
5-5
5-5
5-5
5-5
5-5
5-6
5-6
5-6
Enter Data Format
Data Format Editor
Clear One Data Format
Clear All Data Formats
Off
Data Formatter
*On, but Not Required
On, Required
1
2
3
Alternate Data Formats
VSAF_2
VSAF_3
Secondary Interface Selections
*Disable
Secondary Interface
Enable
2IF_EN0
2IF_EN1
6-2
6-2
Secondary RS-232 Con-
RS-232 Interface
nection
2IFTYP0
2IFTYP64
2IFTYP61
6-2
6-2
6-3
Wand Emulation Same Code
Format
Secondary Code 39
Wand Emulation
Wand Emulation Code 39 For-
mat
12 - 12
4600rp, 4600g/4600r, 4800i User’s Guide
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
5 ms
WNDDLY0
WNDDLY1
WNDDLY2
WNDDLY3
WNDCHK1
WNDCHK0
WNDSPD0
WNDSPD1
WNDSPD2
WNDSPD3
WNDSPD4
WNDSPD5
WNDSPD6
WNDPOL0
WNDPOL1
WNDIDL1
WNDIDL0
WNDBLK0
WNDBLK1
WNDBLK2
WNDBLK3
2IFTRG0
6-3
6-3
6-3
6-3
6-4
6-4
6-4
6-4
6-4
6-4
6-4
6-4
6-4
6-5
6-5
6-5
6-5
6-5
6-5
6-5
6-5
6-6
Wand Emulation Multi
Block
Delay Between Blocks
*50 ms
150 ms
500 ms
On
Overall Checksum
*Off
10
*25
40
Wand Emulation Trans-
mission Rate
80
120
150
200
*Black High
Wand Emulation Polarity
Wand Emulation Idle
White High
*Idle High
Idle Low
20
*40
Data Block Size
60
80
*Manual/Serial Trigger
Read Time-Out
(0 - 300,000 ms) *30,000
TRGSTO####
2IFTRG2
6-6
6-6
6-7
Secondary Trigger Model
Manual Trigger, Low Power
Low Power Time-Out
(0 - 120 seconds) *120
2IFLPT###
Hands Free Time-Out
Scan Stand
Range 0 - 300,000 ms
Scan Stand Mode
TRGPTO######
2IFTRG4
6-7
6-8
6-8
6-8
Presentation Mode
Presentation
2IFTRG3
Symbologies
All Symbologies Off
All Symbologies On
ALLENA0
ALLENA1
7-2
7-2
All Symbologies
4600rp, 4600g/4600r, 4800i User’s Guide
12 - 13
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Default All Codabar
Settings
Codabar
Codabar
CBRDFT
7-3
Off
CBRENA0
CBRENA1
CBRSSX0
CBRSSX1
CBRCK20
CBRCK21
CBRCK22
CBRCCT0
CBRCCT1
CBRCCT2
CBRMIN##
CBRMAX##
7-3
7-3
7-3
7-3
7-4
7-4
7-4
7-5
7-5
7-5
7-5
7-5
*On
*Don’t Transmit
Transmit
Codabar Start/Stop Char.
Codabar Check Char.
*No Check Char.
Validate, But Don’t Transmit
Validate, and Transmit
*Off
Codabar Concatenation
On
Require
Minimum (2 - 60) *4
Maximum (2 - 60) *60
Codabar Message
Length
Default All Code 39
Settings
Code 39
Code 39
C39DFT
7-6
Off
C39ENA0
C39ENA1
C39SSX0
C39SSX1
C39CK20
7-6
7-6
7-6
7-6
7-7
*On
*Don’t Transmit
Transmit
Code 39 Start/Stop Char.
Code 39 Check Char.
*No Check Char.
Validate, But Don’t
Transmit
C39CK21
C39CK22
7-7
7-7
Validate,
and Transmit
Minimum (0 - 48) *0
C39MIN##
C39MAX##
C39APP0
C39APP1
C39B320
C39B321
C39ASC0
C39ASC1
C39DCP
7-7
7-7
7-8
7-8
7-9
7-9
7-9
7-9
7-10
Code 39 Message Length
Code 39 Append
Maximum (0 - 48) *48
*Off
On
*Off
Code 32 Pharmaceutical
(PARAF)
On
*Off
Code 39 Full ASCII
On
Code 39 Code Page
12 - 14
4600rp, 4600g/4600r, 4800i User’s Guide
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Default All Interleaved
2 of 5 Settings
Interleaved 2 of 5
Interleaved 2 of 5
I25DFT
7-10
Off
I25ENA0
I25ENA1
I25CK20
7-10
7-10
7-11
*On
*No Check Char.
Interleaved 2 of 5 Check
Digit
Validate, But Don’t
Transmit
I25CK21
7-11
Validate, and Transmit
Minimum (2 - 80) *4
Maximum (2 - 80) *80
I25CK22
7-11
7-11
7-11
I25MIN##
I25MAX##
Interleaved 2 of 5 Mes-
sage Length
Default All Code 93
Settings
Code 93
Code 93
C93DFT
7-12
Off
C93ENA0
C93ENA1
C93MIN##
C93MAX##
C93DCP
7-12
7-13
7-12
7-12
7-12
*On
Minimum (0 - 80) *0
Maximum (0 - 80) *80
Code 93 Code Page
Code 93 Message Length
Default All Straight 2 of 5
Industrial
Settings
Straight 2 of 5 Industrial
Straight 2 of 5 Industrial
R25DFT
7-13
*Off
R25ENA0
R25ENA1
R25MIN##
R25MAX##
7-13
7-13
7-13
7-13
On
Minimum (1 - 48) *4
Maximum (1 - 48) *48
Straight 2 of 5 Industrial
Message Length
Default All Straight 2 of 5 IATA
Settings
Straight 2 of 5 IATA
Straight 2 of 5 IATA
A25DFT
7-14
*Off
A25ENA0
A25ENA1
A25MIN##
A25MAX##
7-14
7-14
7-14
7-14
On
Minimum (1 - 48) *4
Maximum (1 - 48) *48
Straight 2 of 5 IATA Mes-
sage Length
Settings
Matrix 2 of 5
Matrix 2 of 5
7-15
*Off
On
X25ENA0
X25ENA1
7-15
7-15
4600rp, 4600g/4600r, 4800i User’s Guide
12 - 15
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Minimum (1 - 80) *4
Maximum (1 - 80) *80
X25MIN##
X25MAX##
7-15
7-15
Matrix 2 of 5 Message
Length
Default All Code 11
Settings
Code 11
Code 11
C11DFT
7-15
*Off
C11ENA0
C11ENA1
C11CK20
C11CK21
C11MIN##
C11MAX##
7-16
7-16
7-16
7-16
7-16
7-16
On
1 Check Digit
*2 Check Digits
Minimum (1 - 80) *4
Maximum (1 - 80) *80
Code 11 Check Digits
Required
Code 11 Message Length
Code 128
Default All Code 128
Settings
128DFT
7-17
Off
128ENA0
128ENA1
ISBENA0
ISBENA1
128MIN##
128MAX##
128DCP##
7-17
7-17
7-17
7-17
7-18
7-18
7-18
Code 128
*On
*Off
ISBT Concatenation
On
Minimum (0 - 80) *0
Maximum (0 - 80) *80
Code 128 Code Page (*2)
Code 128 Message
Length
Code 128 Code Page
Telepen
Default All Telepen
Settings
TELDFT
7-19
*Off
TELENA0
TELENA1
TELOLD0
TELOLD1
TELMIN##
TELMAX##
7-19
7-19
7-19
7-19
7-19
7-19
Telepen
On
*AIM Telepen Output
Original Telepen Output
Minimum (1 - 60) *1
Maximum (1 - 60) *60
Telepen Output
Telepen Message Length
Default All
UPC-A Settings
UPC-A
UPC-A
UPADFT
7-20
Off
UPAENA0
UPAENA1
UPACKX0
UPACKX1
7-20
7-20
7-20
7-20
*On
Off
UPC-A Check Digit
*On
12 - 16
4600rp, 4600g/4600r, 4800i User’s Guide
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Off
UPANSX0
UPANSX1
UPAAD20
UPAAD21
UPAAD50
UPAAD51
UPAARQ0
UPAARQ1
UPAADS0
UPAADS1
CPNENA1
CPNENA0
7-20
7-20
7-21
7-21
7-21
7-21
7-21
7-21
7-21
7-21
7-22
7-22
UPC-A Number System
UPC-A 2 Digit Addenda
UPC-A 5 Digit Addenda
*On
*Off
On
*Off
On
*Not Required
UPC-A Addenda
Required
Required
Off
UPC-A Addenda
Separator
*On
*On
UPC-A/EAN-13 with
Extended Coupon Code
Off
Default All UPC-E
Settings
UPC-E0
UPC-E0
UPEDFT
7-22
Off
UPEEN00
UPEEN01
UPEEXP0
UPEEXP1
UPEARQ1
UPEARQ0
UPEADS1
UPEADS0
UPECKX0
UPECKX1
UPENSX0
UPENSX1
UPEAD21
UPEAD20
UPEAD51
UPEEN10
UPEEN11
7-22
7-22
7-22
7-22
7-23
7-23
7-23
7-23
7-23
7-23
7-24
7-24
7-24
7-24
7-24
7-24
7-24
7-24
*On
*Off
UPC-E0 Expand
On
Required
UPC-E0 Addenda
Required
*Not Required
*On
UPC-E0 Addenda Sepa-
rator
Off
Off
UPC-E0 Check Digit
*On
Off
UPC-E0 Number System
*On
2 Digit Addenda On
*2 Digit Addenda Off
5 Digit Addenda On
*Off
UPC-E0 Addenda
UPC-E1
On
Default All EAN/
JAN Settings
EAN/JAN-13
E13DFT
7-25
4600rp, 4600g/4600r, 4800i User’s Guide
12 - 17
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Off
E13ENA0
E13ENA1
E13CKX0
E13CKX1
E13AD21
E13AD20
E13AD51
E13AD50
E13ARQ0
E13ARQ1
E13ADS0
E13ADS1
E13ISB0
E13ISB1
7-25
7-25
7-25
7-25
7-26
7-26
7-26
7-26
7-26
7-26
7-26
7-26
7-27
7-27
EAN/JAN-13
*On
Off
EAN/JAN-13 Check Digit
*On
2 Digit Addenda On
*2 Digit Addenda Off
5 Digit Addenda On
*5 Digit Addenda Off
*Not Required
Required
EAN/JAN-13 2 Digit
Addenda
EAN/JAN-13 Addenda
Required
Off
EAN/JAN-13 Addenda
Separator
*On
*Off
ISBN Translate
EAN/JAN-8
On
Default All EAN/
JAN 8 Settings
EA8DFT
7-27
Off
EA8ENA0
EA8ENA1
EA8CKX0
EA8CKX1
EA8AD20
EA8AD21
EA8AD50
EA8AD51
EA8ARQ0
EA8ARQ1
EA8ADS0
EA8ADS1
MSIDFT
7-27
7-27
7-27
7-27
7-28
7-28
7-28
7-28
7-28
7-28
7-28
7-28
7-29
7-29
EAN/JAN-8
*On
Off
EAN/JAN-8 Check Digit
EAN/JAN-8 Addenda
*On
*2 Digit Addenda Off
2 Digit Addenda On
*5 Digit Addenda Off
5 Digit Addenda On
*Not Required
Required
EAN/JAN-8 Addenda
Required
Off
EAN/JAN-8 Addenda
Separator
*On
MSI
MSI
Default All MSI Settings
*Off
MSIENA0
MSIENA1
On
12 - 18
4600rp, 4600g/4600r, 4800i User’s Guide
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
*Validate Type 10, but Don’t
Transmit
MSICHK0
MSICHK1
7-29
7-29
MSI Check Character
Validate Type 10 and
Transmit
Minimum (4 - 48) *4
Maximum (4 - 48) *48
Default All Plessey Settings
*Off
MSIMIN##
MSIMAX##
PLSDFT
7-30
7-30
7-30
7-30
7-30
7-30
7-30
MSI Message Length
Plessey Code
PLSENA0
PLSENA1
PLSMIN##
PLSMAX##
Plessey Code
On
Minimum (4 - 48) *4
Maximum (4 - 48) *48
Plessey Message Length
Default All
GS1 DataBar Omnidirectional
Settings
GS1 DataBar Omnidirec-
tional
RSSDFT
7-31
Off
RSSENA0
RSSENA1
7-31
7-31
GS1 DataBar Omnidirec-
tional
*On
Default All GS1 DataBar
Limited Settings
GS1 DataBar Limited
GS1 DataBar Limited
GS1 DataBar Expanded
GS1 DataBar Expanded
RSLDFT
7-31
Off
RSLENA0
RSLENA1
7-31
7-31
*On
Default All GS1 DataBar
Expanded Settings
RSEDFT
7-31
Off
RSEENA0
RSEENA1
RSEMIN##
RSEMAX##
POSDFT
7-31
7-32
7-32
7-32
7-34
7-33
7-33
7-33
7-33
7-33
7-33
7-33
*On
Minimum (4 - 74) *4
Maximum (4 - 74) *74
Default All PosiCode Settings
Off
GS1 DataBar Expanded
Msg. Length
PosiCode
POSENA0
POSENA1
POSLIM0
POSLIM2
POSMIN##
POSMAX##
*On
PosiCode
A and B On
*A and B and Limited B On
Minimum (2 - 80) *4
Maximum (2 - 80) *48
PosiCode Msg. Length
4600rp, 4600g/4600r, 4800i User’s Guide
12 - 19
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
*Off
On
TRIENA0
TRIENA1
7-34
7-34
Trioptic Code
Codablock F
Codablock F
Default All Codablock F Set-
tings
CBFDFT
7-34
*Off
CBFENA0
CBFENA1
CBFMIN####
CBFMAX####
16KDFT
7-34
7-34
7-34
7-34
7-35
7-35
7-35
7-35
7-35
7-36
7-36
7-36
7-36
7-36
7-37
7-37
7-37
7-37
7-37
On
Minimum (1 - 2048) *1
Maximum (1 - 2048) *2048
Default All Code 16K Settings
*Off
Codablock F Msg. Length
Code 16K
16KENA0
16KENA1
16KMIN###
16KMAX###
C49DFT
Code 16K
On
Minimum (0 - 160) *1
Maximum (0 - 160) *160
Default All Code 49 Settings
Off
Code 16K Msg. Length
Code 49
C49ENA0
C49ENA1
C49MIN##
C49MAX##
PDFDFT
Code 49
*On
Minimum (1 - 81) *1
Maximum (1 - 81) *81
Default All PDF417 Settings
*On
Code 49 Msg. Length
PDF417
PDFENA1
PDFENA0
PDFMIN
PDF417
Off
Minimum (1-2750) *1
Maximum (1-2750) *2750
PDF417 Msg. Length
MicroPDF417
PDFMAX
Default All Micro PDF417 Set-
tings
MPDDFT
7-38
On
MPDENA1
MPDENA0
MPDMIN
7-38
7-38
7-38
7-38
7-38
7-39
7-39
MicroPDF417
*Off
Minimum (1-366) *1
MicroPDF417 Msg.
Length
Maximum (1-366) *366
MPDMAX
COMENA0
COMUPC1
COMUPC0
On
EAN•UCC Composite
Codes
*Off
On
UPC/EAN Version
*Off
12 - 20
4600rp, 4600g/4600r, 4800i User’s Guide
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Minimum (1-2435) *1
COMMIN
COMMAX
EANEMU2
EANEMU1
EANEMU0
T39ENA1
T39ENA0
4CBENA1
4CBENA0
TAGENA1
TAGENA0
NETENA1
NETENA0
NETCKX1
NETCKX0
PLNENA1
PLNENA0
PLNCKX1
PLNCKX0
BPOENA1
BPOENA0
CANENA1
CANENA0
KIXENA1
KIXENA0
AUSENA1
AUSENA0
AUSINT0
AUSINT1
JAPENA1
JAPENA0
CPCDFT
7-39
7-39
7-40
7-40
7-40
7-40
7-40
7-41
7-41
7-41
7-41
7-41
7-41
7-42
7-42
7-41
7-42
7-42
7-42
7-43
7-43
7-42
7-41
7-44
7-43
7-43
7-44
7-44
7-44
7-44
7-43
7-43
7-45
EAN•UCC Composite
Codes Msg. Length
Maximum (1-2435) *2435
RSS Emulation
EAN•UCC Emulation
EAN•UCC-128 Emulation
*EAN•UCC Emulation Off
On
TCIF Linked Code 39
(TLC39)
*Off
On
4-CB (4-State Customer
Barcode)
*Off
On
ID-tag (UPU 4-State)
Postnet
*Off
On
*Off
Transmit
Postnet Check Digit
Planet Code
*Don’t Transmit
On
*Off
Transmit
Planet Code Check Digit
British Post
*Don’t Transmit
On
*Off
On
Canadian Post
*Off
On
Kix (Netherlands) Post
Australian Post
*Off
On
*Off
*Bar Output
Australian Post Interpre-
tation
Numeric N Table
On
Japanese Post
China Post
*Off
Default All China Post Settings
4600rp, 4600g/4600r, 4800i User’s Guide
12 - 21
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
*Off
CPCENA0
CPCENA1
CPCMIN##
CPCMAX##
KPCDFT
7-45
7-45
7-45
7-45
7-46
7-46
7-46
7-46
7-46
7-47
7-47
7-47
7-47
7-47
China Post
On
Minimum (2 - 80) *4
Maximum (2 - 80) *80
Default All Korea Post Settings
*Off
China Post Msg. Length
Korea Post
KPCENA0
KPCENA1
KPCMIN##
KPCMAX##
QRCDFT
Korea Post
On
Minimum (2 - 80) *4
Maximum (2 - 80) *48
Default All QR Code Settings
*On
Korea Post Msg. Length
QR Code
QRCENA1
QRCENA0
QRCMIN
QR Code
Off
Minimum (1-3500) *1
Maximum (1-3500) *3500
QR Code Msg. Length
Data Matrix
QRCMAX
Default All Data Matrix Set-
tings
IDMDFT
7-48
*On
IDMENA1
IDMENA0
IDMMIN
7-48
7-48
7-48
7-48
7-49
7-49
7-49
7-49
7-49
Data Matrix
Off
Minimum (1-1500) *1
Maximum (1-1500) *1500
Default All MaxiCode Settings
*On
Data Matrix Msg. Length
MaxiCode
IDMMAX
MAXDFT
MAXENA1
MAXENA0
MAXMIN
MAXMAX
MaxiCode
Off
Minimum (1-150) *1
Maximum (1-150) *150
MaxiCode Msg. Length
Default All Aztec Code Set-
tings
Aztec Code
Aztec Code
AZTDFT
7-50
*On
AZTENA1
AZTENA0
AZTMIN
7-50
7-50
7-50
7-50
7-50
Off
Minimum (1-3750) *1
Maximum (1-3750) *3750
Enable Runes
*Disable Runes
Aztec Code Msg. Length
Aztec Runes
AZTMAX
AZTRUN1
AZTRUN0
12 - 22
4600rp, 4600g/4600r, 4800i User’s Guide
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Imaging Default Commands
Default all Imaging Commands
IMGDFT
8-1
8-2
8-2
8-2
8-2
8-2
Image Snap
Imaging Style - Decoding
*Imaging Style - Photo
Imaging Style - Manual
Beeper On
SNPSTY0
SNPSTY1
SNPSTY2
SNPBEP1
SNPBEP0
*Beeper Off
Exposure (1-7874 microsec-
onds)
SNPEXP
8-3
*Gain - None
SNPGAN1
SNPGAN2
SNPGAN4
SNPGAN8
8-4
8-4
8-4
8-4
Gain - Medium
Gain - Heavy
Gain - Maximum
Delta for Acceptance (0-255)
*25
SNPDEL###
8-4
*LED State - Off
SNPLED0
SNPLED1
SNPTRG0
SNPTRG1
SNPTRY##
8-3
8-3
8-2
8-2
8-4
LED State - On
*Wait for Trigger Off
Wait for Trigger On
Update Tries (0-10) *6
Target White Value (0-255)
*125
SNPWHT###
SNPPCT##
8-4
8-5
Target Set Point Percentage
(1-99) *50
4600rp, 4600g/4600r, 4800i User’s Guide
12 - 23
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Image Ship
*Infinity Filter - Off
Infinity Filter - On
*Compensation Off
Compensation On
IMGINF0
IMGINF1
IMGCOR0
IMGCOR1
8-6
8-6
8-7
8-7
*Pixel Depth - 8 bits/pixel
(grayscale)
IMGBPP8
8-7
Pixel Depth - 1 bit/pixel (B&W)
*Don’t Sharpen Edges
Sharpen Edges (0-23)
*File Format - JPEG
IMGBPP1
IMGEDG0
IMGEDG##
IMGFMT6
IMGFMT0
IMGFMT1
8-7
8-7
8-7
8-8
8-8
8-8
File Format - KIM
File Format - TIFF binary
File Format - TIFF binary
group 4, compressed
IMGFMT2
IMGFMT3
IMGFMT4
8-8
8-8
8-8
File Format - TIFF grayscale
File Format - Uncompressed
binary
File Format - Uncompressed
grayscale
IMGFMT5
8-8
File Format - BMP
IMGFMT8
IMGHIS0
IMGHIS1
IMGNVX1
IMGNVY1
IMGFSP0
IMGFSP1
IMGROT3
8-8
8-8
8-8
8-9
8-9
8-9
8-9
8-10
*Histogram Stretch Off
Histogram Stretch On
Invert Image around X axis
Invert Image around Y axis
*Noise Reduction Off
Noise Reduction On
Rotate Image 90° left
JPEG Image Quality (0-100)
*50
IMGJQF###
IMGGAM0
8-10
8-11
8-11
8-12
8-12
8-12
*Gamma Correction Off
Gamma Correction On (1-
1000)
IMGGAM###
IMGWNL###
IMGWNR###
IMGWNT###
Image Crop - Left (0-640) *0
Image Crop - Right (0-640)
*639
Image Crop - Top (0-480) *0
12 - 24
4600rp, 4600g/4600r, 4800i User’s Guide
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Image Crop - Bottom (0-480)
*479
IMGWNB###
IMGMAR###
8-12
8-12
Image Crop - Margin (0-238)
*0
Protocol - None (raw)
IMGXFR0
IMGXFR2
8-13
8-13
Protocol - None (default USB)
Protocol - Hmodem Com-
pressed
IMGXFR3
8-13
Protocol - Hmodem
Ship Every Pixel
IMGXFR4
IMGSUB1
IMGSUB2
IMGSUB3
IMGUSH0
8-13
8-13
8-13
8-13
8-14
Image Ship (continued)
Ship Every 2nd Pixel
Ship Every 3rd Pixel
*Document Image Filter Off
Document Image Filter On (0-
255)
IMGUSH###
8-14
*Don’t Ship Histogram
Ship Histogram
IMGHST0
IMGHST1
8-15
8-15
OCR Selections
Default All OCR Settings
OCR-A On
OCRDFT
9-1
9-1
9-2
9-2
9-2
9-3
9-3
OCRENA1
OCRENA2
OCRENA3
OCRENA4
OCRENA5
OCRENA0
OCR-B On
OCR
U.S. Currency On
MICR E 13 B On
SEMI Font
* All OCR Off
4600rp, 4600g/4600r, 4800i User’s Guide
12 - 25
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
9-8
“OCRCHK01234
56789”
OCR Mod. 10 Check Char.
OCR Mod. 36 Check Char.
“OCRCHK01234
56789ABCDEFG
HIJKLM-
9-9
NOPQRSTU-
VWXYZ”
OCR Check Character
OCR User-Defined Check
Char.
OCRCHK
9-9
3-1-3-1 Weighted Mod. 10
Check Char.
OCRCHK3-1-3-1
OCRCHK2-1-2-1
9-10
9-11
2-1-2-1 Weighted Mod. 10
Check Char.
Enter OCR Template
OCRTMP
OCRGPG
OCRGPH
9-13
9-13
9-13
OCR Templates
Enter User-Defined Variable g
Enter User-Defined Variable h
12 - 26
4600rp, 4600g/4600r, 4800i User’s Guide
13
Product Specifications
4600g and 4600r
Parameter
Specification
4600g/4600r Dimensions
(Typical):
Height
6.2 inches (15.7 cm)
5.3 inches (13.5 cm)
3.2 inches (8.1 cm)
6.5 ounces (184.3 g)
Length
Width
Weight
4600rp Dimensions (Typical):
Height (Stand and imager)
Length (Stand)
8.2 inches (20.8 cm)
5.4 inches (13.7 cm)
Length (Back edge of stand to
front of imager nose with image
in upright position)
6.5 inches (16.5 cm)
Width (Stand base)
3.5 inches (8.9 cm)
14.9 ounces (422 g)
Weight (Stand and imager)
Illumination:
Scan LEDs
Aiming LEDs
617nm +30nm
526nm +30nm
VGA, 640x480 (4X00); 752x480 (5X00). Binary, TIFF,
or JPEG output.
Image
Skew Angle
Pitch Angle
40 degrees
40 degrees
Motion Tolerance:
Streaming Presentation Trigger
Other Trigger Selections
20 inches (50 cm) per second
4 inches (10 cm) per second
Symbol Contrast
Grade 1.0 (20% or greater)
4 - 14 VDC at imager
Voltage Requirements
Input
5V
12V
Scanning
334mA
170mA
Standby Inrush Low Power
Current Draw (Typical):
80mA
55mA
500mA 100µA
Power Supply Noise Rejection
Temperature Ranges:
Operating
Maximum 100mV peak to peak, 10 to 100 kHz
+32°F to +122°F (0°C to +50°C)
-40°F to +140°F (-40°C to +60°C)
0 to 95% non-condensing
Storage
Humidity
4600rp, 4600g/4600r, 4800i User’s Guide
13 - 1
Operational after 50 drops from 6 feet
(1.8 m) to concrete
Mechanical Drop
Vibration
Withstands 5G peak from 22 to 300 Hz
15 kV to any external surface
ESD Tolerance
International: CB Scheme to IEC60950-1 and
IEC60825-1 (Class 1 LED)
(4600r only) South Korea: MIC
Australia/NZ: C-Tick marked.
Europe:
CE 2004/108/EC EMC directive to EN55022
Class A, EN55024, EN61000-3-2, EN61000-3-3
2006/95/EC Low Voltage Directive
Germany: GS Mark
Agency Compliance
(4600r only) Korea: MIC Class A
Mexico: NOM-NYCE
USA:
FCC Part 15 Subpart B Class A
UL listed to 60950-1
Canada:
ICES-003 (Class A)
cUL listed to CSA C22.2 No. 60950-1-3
4800i
Parameter
Specification
Dimensions (Typical):
Height
6.2 inches (15.7 cm)
5.3 inches (13.5 cm)
3.2 inches (8.1 cm)
6.5 ounces (184.3 g)
Length
Width
Weight
Illumination:
Scan LEDs
Aiming LEDs
617nm +30nm
526nm +30nm
VGA, 640x480 (4X00); 752x480 (5X00). Binary, TIFF,
or JPEG output.
Image
Skew Angle
Pitch Angle
40 degrees
40 degrees
Motion Tolerance:
Streaming Presentation Trigger
Other Trigger Selections
20 inches (50 cm) per second
4 inches (10 cm) per second
Symbol Contrast
Grade 1.0 (20% or greater)
4 - 14 VDC at imager
Voltage Requirements
13 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
Input
5V
12V
Scanning
334mA
170mA
Standby Inrush Low Power
Current Draw (Typical):
80mA
55mA
500mA 100µA
Power Supply Noise Rejection
Temperature Ranges:
Operating
Maximum 100mV peak to peak, 10 to 100 kHz
+14°F to +122°F (-10°C to +50°C)
-40°F to +158°F (-40°C to +70°C)
0 to 95% non-condensing
Storage
Humidity
Operational after 50 drops from 6.5 feet
(2 m) to concrete at 10°C
Mechanical Drop
Vibration
Withstands 5G peak from 22 to 300 Hz
15 kV to any external surface
ESD Tolerance
International: CB Scheme to IEC60950-1 and
IEC60825-1 (Class 1 LED)
Australia/NZ: C-Tick marked.
Europe:
CE 2004/108/EC EMC directive to EN55022
Class A, EN55024, EN61000-3-2, EN61000-3-3
2006/95/EC Low Voltage Directive
Mexico: NOM-NYCE
Agency Compliance
USA:
FCC Part 15 Subpart B Class A
UL listed to 60950-1
Canada:
ICES-003 (Class A)
cUL listed to CSA C22.2 No. 60950-1-3
4600rp, 4600g/4600r, 4800i User’s Guide
13 - 3
13 - 8
4600rp, 4600g/4600r, 4800i User’s Guide
14
Maintenance
Repairs
Repairs and/or upgrades are not to be performed on this product. These
services are to be performed only by an authorized service center. See
"Customer Support" on page 15-1 for further information.
Maintenance
Your imager provides reliable and efficient operation with a minimum of care.
Although specific maintenance is not required, the following periodic checks
ensure dependable imager operation:
Cleaning the Device
Reading performance may degrade if the imager’s window is not clean. If the
window is visibly dirty, or if the imager isn’t operating well, clean the window with
a soft cloth or lens tissue dampened with water (or a mild detergent- water
solution). If a detergent solution is used, rinse with a clean lens tissue dampened
with water only.
The imager’s housing may also be cleaned the same way.
Caution:
!
Do not submerge the imager in water. Do not use
abrasive wipes or tissues on the imager’s window –
abrasive wipes may scratch the window.
Never use solvents (e.g., acetone, benzene, ether, or
phenol-based agents) on the housing or window –
solvents may damage the finish or the window.
Inspecting Cords and Connectors
Inspect the imager’s interface cable and connector for wear or other signs of
operation. Contact your Hand Held Products distributor for information about
cable replacement. Cable replacement instructions are on page 14-2.
4600rp, 4600g/4600r, 4800i User’s Guide
14 - 1
Replacing the Interface Cable
The standard interface cable is attached to the imager with an 10-pin modular
connector. When properly seated, the connector is held in the imager’s handle
by a flexible retention tab. The interface cable is designed to be field
replaceable.
•
Order replacement cables from Hand Held Products or from an authorized
distributor.
•
When ordering a replacement cable, specify the cable part number of the
original interface cable.
To Replace the 4600g/4600r Interface Cable:
1. Turn the power to the host system
OFF.
2. Disconnect the imager’s cable from
the terminal or computer.
3. Locate the small hole on the side of
the imager’s handle. This is the cable
release.
4. Straighten one end of a paper clip.
5. Insert the end of the paper clip into the
small hole and press in. This
depresses the retention tab, releasing
the connector. Pull the connector out
while maintaining pressure on the
paper clip, then remove the paper clip.
Cable
Release
6. Replace with the new cable.
Insert the connector into the opening
and press firmly. The connector is
keyed to go in only one way, and will click into place.
14 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
To Replace the 4600rp Interface Cable:
1. Turn the power to the host system
OFF.
2. Disconnect the imager’s cable from
the terminal or computer.
3. Rotate the imager downward to the
last position.
4. Locate the small hole on the side of
the stand. This is the cable release.
5. Straighten one end of a paper clip.
6. Insert the end of the paper clip into the
small hole and press in. This
depresses the retention tab, releasing the connector. Pull the connector out
while maintaining pressure on the paper clip, then remove the paper clip.
7. Replace with the new cable.
Insert the connector into the opening and press firmly. The connector is
keyed to go in only one way, and will click into place.
To Replace the 4800i Interface Cable:
1. Turn the power to the host system
OFF.
2. Disconnect the imager’s cable from
the terminal or computer.
3. Use a screwdriver to unscrew the cord
lock from the base of the imager.
4. Locate the small hole on the side of
the imager’s handle. This is the cable
release.
5. Straighten one end of a paper clip.
Cable
Release
6. Insert the end of the paper clip into the
small hole and press in. This
depresses the retention tab, releasing
the connector. Pull the connector out
paper clip, then remove the paper clip.
7. Replace with the new cable.
Insert the connector into the opening
and press firmly. The connector is
keyed to go in only one way, and will click into place.
4600rp, 4600g/4600r, 4800i User’s Guide
14 - 3
8. Screw the cord lock back in place over the cord.
Troubleshooting
The imager automatically performs self-tests whenever you turn it on. If your
imager is not functioning properly, review the following Troubleshooting Guide to
try to isolate the problem.
Is the power on? Is the red aiming illumination line on?
If the red aiming illumination line isn’t illuminated, check that:
•
•
•
The cable is connected properly.
The host system power is on (if external power isn’t used).
The trigger works.
Is the imager having trouble reading your symbols?
If the imager isn’t reading symbols well, check that the symbols:
•
•
•
Aren’t smeared, rough, scratched, or exhibiting voids.
Aren’t coated with frost or water droplets on the surface.
Are enabled in the imager or in the decoder to which the imager connects.
Is the barcode displayed but not entered?
The barcode is displayed on the host device correctly, but you still have to press
a key to enter it (the Enter/Return key or the Tab key, for example).
You need to program a suffix. Programming a suffix enables the imager to output
the barcode data plus the key you need (such as “CR”) to enter the data into your
application. Refer to "Prefix/Suffix Overview" on page 4-1 for further information.
Does the imager read the barcode incorrectly?
If the imager reads a barcode, but the data is not displayed correctly on the host
screen:
•
The imager may not be programmed for the appropriate terminal interface.
For example, you scan “12345” and the host displays “@es%.”
Reprogram the imager with the correct Plug and Play or Terminal selection
barcode. See Chapter 1 and Chapter 2.
•
The imager may not be programmed to output your barcode data properly.
Reprogram the imager with the proper symbology selections. See Chapter 7.
The imager won’t read your barcode at all.
14 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
1. Scan the sample barcodes in the back of this manual. If the imager reads
the sample barcodes, check that your barcode is readable.
Verify that your barcode symbology is enabled (see Chapter 7).
2. If the imager still can’t read the sample barcodes, scan "All Symbologies" on
page 7-2.
If you aren’t sure what programming options have been set in the imager, or if
you want the factory default settings restored, scan Standard Product Default
Settings on page 12-4.
4600rp, 4600g/4600r, 4800i User’s Guide
14 - 5
14 - 6
4600rp, 4600g/4600r, 4800i User’s Guide
15
Customer Support
Technical Assistance
If you need assistance installing or troubleshooting, please call your Distributor
or the nearest Hand Held Products technical support office:
North America/Canada
Telephone: (800) 782-4263
Fax number: (315) 554-6705
E-mail: [email protected]
Latin America
Telephone: (803) 835-8000
Telephone: (800) 782-4263
E-mail: [email protected]
Brazil
Telephone: +55 (21) 3535-9100
Fax: +55 (21) 3535-9105
E-mail: [email protected]
Mexico
Telephone: (803) 835-8000
E-mail: [email protected]
Europe, Middle East, and Africa
Telephone: +31 (0) 40 7999 393
Fax: +31 (0) 40 2425 672
E-mail: [email protected]
Asia Pacific
Telephone - Hong Kong: +852-3188-3485 or 2511-3050
Telephone - China: +86 21 6361 3818
E-mail: [email protected]
Japan
Telephone: +813 5770-6312
E-mail: [email protected]
Malaysia
Telephone: +603-6201-7020
E-mail: [email protected]
4600rp, 4600g/4600r, 4800i User’s Guide
15 - 1
Online Technical Assistance
For Further Information
To download the full User’s Guide for these products, visit our website at
Product Service and Repair
Hand Held Products provides service for all its products through service centers
throughout the world. To obtain warranty or non-warranty service, return the unit
to Hand Held Products (postage paid) with a copy of the dated purchase record
attached. Contact the appropriate location below to obtain a Return Material
Authorization number (RMA #) before returning the product.
North America
Telephone: (800) 782-4263
Fax: (803) 835-8012
E-mail: [email protected]
Latin America
Telephone: (803) 835-8000
Telephone: (800) 782-4263
Fax: (239) 263-9689
E-mail: [email protected]
Brazil
Telephone: +55 (21) 3535-9100
Fax: +55 (21) 3535-9105
E-mail: [email protected]
Mexico
Telephone: +52 (55) 5203-2100
Fax: +52 (55) 5531-3672
E-mail: [email protected]
Europe, Middle East, and Africa
Telephone:
+31 (0) 40 2901 633
Fax: +31 (0) 40 2901 631
E-mail: [email protected]
Asia Pacific
Telephone: +852-2511-3050
Fax: +852-2511-3557
E-mail: [email protected]
15 - 2
4600rp, 4600g/4600r, 4800i User’s Guide
Japan
Telephone: +813-5770-6312
Fax: +813-5770-6313
E-mail: [email protected]
Online Product Service and Repair Assistance
You can also access product service and repair assistance online at
Limited Warranty
Hand Held Products, Inc. ("Hand Held Products") warrants its products to be free
from defects in materials and workmanship and to conform to Hand Held
Products’ published specifications applicable to the products purchased at the
time of shipment. This warranty does not cover any Hand Held Products product
which is (i) improperly installed or used; (ii) damaged by accident or negligence,
including failure to follow the proper maintenance, service, and cleaning
schedule; or (iii) damaged as a result of (A) modification or alteration by the
purchaser or other party, (B) excessive voltage or current supplied to or drawn
from the interface connections, (C) static electricity or electro-static discharge,
(D) operation under conditions beyond the specified operating parameters, or (E)
repair or service of the product by anyone other than Hand Held Products or its
authorized representatives.
This warranty shall extend from the time of shipment for the duration published
by Hand Held Products for the product at the time of purchase ("Warranty
Period"). Any defective product must be returned (at purchaser’s expense)
during the Warranty Period to Hand Held Products’ factory or authorized service
center for inspection. No product will be accepted by Hand Held Products
without a Return Materials Authorization, which may be obtained by contacting
Hand Held Products. In the event that the product is returned to Hand Held
Products or its authorized service center within the Warranty Period and Hand
Held Products determines to its satisfaction that the product is defective due to
defects in materials or workmanship, Hand Held Products, at its sole option, will
either repair or replace the product without charge, except for return shipping to
Hand Held Products.
EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE
FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR
WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
EXCLUSIVE REMEDY UNDER THIS WARRANTY IS LIMITED TO THE
REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT. IN NO EVENT
SHALL HAND HELD PRODUCTS BE LIABLE FOR INDIRECT, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES, AND, IN NO EVENT, SHALL ANY
LIABILITY OF HAND HELD PRODUCTS ARISING IN CONNECTION WITH
4600rp, 4600g/4600r, 4800i User’s Guide
15 - 3
ANY PRODUCT SOLD HEREUNDER (WHETHER SUCH LIABILITY ARISES
FROM A CLAIM BASED ON CONTRACT, WARRANTY, TORT, OR
OTHERWISE) EXCEED THE ACTUAL AMOUNT PAID TO HAND HELD
PRODUCTS FOR THE PRODUCT. THESE LIMITATIONS ON LIABILITY
SHALL REMAIN IN FULL FORCE AND EFFECT EVEN WHEN HAND HELD
PRODUCTS MAY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
INJURIES, LOSSES, OR DAMAGES. SOME STATES, PROVINCES, OR
COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
All provisions of this Limited Warranty are separate and severable, which means
that if any provision is held invalid and unenforceable, such determination shall
not affect the validity of enforceability of the other provisions hereof. Use of any
peripherals not manufactured/sold by Hand Held Products voids the warranty.
This includes but is not limited to: cables, power supplies, cradles, and docking
stations. Hand Held Products, Inc. extends these warranties only to the first end-
users of the products. These warranties are nontransferable.
The limited duration of the warranty for the 4600g, 4600r, 4600rp, or 4800i is for
five (5) years.
15 - 4
4600rp, 4600g/4600r, 4800i User’s Guide
A
Appendix A
Symbology Chart
AIM
ID
Possible AIM ID
Modifiers (m)
Code ID
(hex)
Symbology
All Symbologies
4-CB (4-State Customer Barcode)
Australian Post
Aztec Code
(0x99)
]X0
M (0x4D)
A (0x41)
z (0x7A)
B (0x42)
C (0x43)
Q (0x51)
a (0x61)
q (0x71)
h (0x68)
j (0x6A)
o (0x6F)
< (0x3C)
b (0x62)
l (0x6C
]X0
]zm
]X0
0-9, A-C
British Post
Canadian Post
China Post
]X0
]X0
Codabar
]Fm
]Om
]H3
]Cm
]Km
]X0
0-1
Codablock F
0, 1, 4, 5, 6
Code 11
Code 128
0, 1, 2, 4
0, 1, 2, 4
Code 16K
Code 32 Pharmaceutical (PARAF)
Code 39
]Am
]Tm
]Gm
0, 1, 3, 4, 5, 7
0, 1, 2, 4
Code 49
0-9, A-Z,
a-m
i (0x69
Code 93 and 93i
Data Matrix
EAN-13
]dm
]E0
]E4
]em
]E3
0-6
w (0x77)
d (0x64)
D (0x44)
y (0x79)
d (0x64)
EAN-8
EAN•UCC Composite
0-3
EAN-13 with Extended
Coupon Code
ID-tag (UPU 4-State)
Interleaved 2 of 5
Japanese Post
KIX (Netherlands) Post
Korea Post
]X0
]lm
N (0x4E)
e (0x65)
K (0x4B)
? (0x3F)
m (0x6D)
x (0x78)
0, 1, 3
]X0
]X0
]X0
]Um
Matrix 2 of 5
MaxiCode
0-3
4600rp, 4600g/4600r, 4800i User’s Guide
A - 1
AIM
ID
Possible AIM ID
Modifiers (m)
Code ID
(hex)
Symbology
MicroPDF417
MSI
]Lm
3-5
0
R (0x52)
g (0x67)
(0x9C)
]Mm
No Read
OCR-A
]o1
O (0x4F)
O (0x4F)
O (0x4F)
O (0x4F)
O (0x4F)
r (0x72)
L (0x4C)
n (0x6E)
W (0x57)
P (0x50)
s (0x73)
y (0x79)
OCR-B
]o2
MICR E-13B
U.S. Currency Font
SEMI Font
PDF417
]ZE
]o3
]o3
]Lm
]X0
]P0
]pm
]X0
]Qm
]em
0-2
Planet Code
Plessey Code
PosiCode
0, 1, 2
Postnet
QR/Micro QR Code
0-6
0
Reduced Space Symbology (RSS-14,
RSS Limited, RSS Expanded)
Straight 2 of 5 IATA (two-bar start/
stop)
]Rm
0, 1, 3
f (0x66)
TCIF Linked Code 39 (TLC39)
]L2
]Bm
]X0
]C1
]E0
]E3
]E0
]X0
T (0x54)
t (0x74)
= (0x3D)
I (0x49)
c (0x63)
c (0x63)
E (0x45)
v (0x76)
Telepen
0, 1, 2, 4
Trioptic Code
UCC/EAN-128
UPC-A
UPC-A with Extended Coupon Code
UPC-E
VeriCode*
* Only available by special order.
A - 2
4600rp, 4600g/4600r, 4800i User’s Guide
Note: “m” represents the AIM modifier character. Refer to International
Technical Specification, Symbology Identifiers, for AIM modifier character
details.
Note: Prefix/Suffix entries for specific symbologies override the universal (All
Symbologies, 99) entry.
Refer to Data Editing beginning on page 4-1 and Data Formatting beginning on
page 5-1 for information about using Code ID and AIM ID.
4600rp, 4600g/4600r, 4800i User’s Guide
A - 3
ASCII Conversion Chart (Code Page 1252)
Note: This table applies to U.S. style keyboards. Certain characters may differ depending on your
Country Code/PC regional settings.
Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Char
0
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
@
A
B
C
D
E
F
G
H
l
96
97
98
99
60
61
62
63
‘
1
!
a
b
c
d
e
f
2
“
3
#
$
%
&
‘
4
100 64
101 65
102 66
103 67
104 68
105 69
106 6A
107 6B
108 6C
109 6D
110 6E
5
6
7
g
h
i
8
(
9
HT
)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
LF
*
J
j
VT
+
,
K
L
k
l
FF
CR
-
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
m
n
o
p
q
r
SO
.
SI
/
111
6F
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
0
1
2
3
4
5
6
7
8
9
:
112 70
113 71
114 72
115 73
116 74
117 75
118 76
119 77
120 78
121 79
122 7A
124 7C
125 7D
126 7E
127 7F
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
s
t
u
v
w
x
y
z
SUB
ESC
FS
;
<
=
>
?
\
|
GS
]
}
RS
^
~
US
_
A - 4
4600rp, 4600g/4600r, 4800i User’s Guide
Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Char
128
129
130
131
132
133
134
135
136
137
138
80
81
82
83
84
85
86
87
88
89
8A
€
160 A0
161 A1
162 A2
163 A3
164 A4
165 A5
166 A6
167 A7
168 A8
169 A9
170 AA
192 C0
193 C1
194 C2
195 C3
196 C4
197 C5
198 C6
199 C7
200 C8
201 C9
202 CA
À
Á
Â
Ã
Ä
Å
Æ
Ç
È
É
Ê
224
225
226
227
228
229
230
231
232
233
234
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
à
á
â
ã
ä
å
æ
ç
¡
‚
¢
£
¤
¥
¦
ƒ
„
…
†
‡
ˆ
§
¨
è
é
ê
‰
Š
©
ª
«
¬
-
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
8B
8C
8D
8E
8F
90
91
92
93
94
95
96
97
98
99
9A
‹
171 AB
172 AC
173 AD
174 AE
175 AF
176 B0
177 B1
178 B2
179 B3
180 B4
181 B5
182 B6
183 B7
184 B8
185 B9
186 BA
203 CB
204 CC
205 CD
206 CE
207 CF
208 D0
209 D1
210 D2
211 D3
212 D4
213 D5
214 D6
215 D7
216 D8
217 D9
218 DA
Ë
Ì
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
ë
ì
Œ
Í
í
Ž
®
¯
Î
î
Ï
ï
°
Ð
Ñ
Ò
Ó
Ô
Õ
Ö
×
Ø
Ù
Ú
ð
ñ
ò
ó
ô
õ
ö
÷
ø
ù
ú
‘
’
²
“
³
”
´
•
µ
¶
·
–
—
˜
¸
™
š
¹
155
156
157
158
159
9B
9C
9D
9E
9F
›
187 BB
188 BC
189 BD
190 BE
191 BF
»
219 DB
220 DC
221 DD
223 DF
Û
Ü
Ý
ß
251
252
253
255
FB
FC
FD
FF
û
ü
ý
þ
ÿ
œ
¼
½
¿
ž
Ÿ
4600rp, 4600g/4600r, 4800i User’s Guide
A - 5
Code Page Mapping of Printed Barcodes
Code pages define the mapping of character codes to characters. If the data
received does not display with the proper characters, it may be because the
barcode being scanned was created using a code page that is different from the
one the host program is expecting. If this is the case, select the code page with
which the barcodes were created. The data characters should then appear
properly.
Note: The Code Page option is available for Code 39, Code 93, and Code 128.
Code Page Standard
Description
1
CP ISO646
ISO 2022
2 (Default)
Automatic National Replacement Charac-
ters
3
CP Binary
82
83
81
84
85
86
87
88
89
90
ISO 2022 11 Swe
ISO 2022 69 Fra
ISO 2022 25 Fra
ISO 2022 11 Ger
ISO 2022 11 Ita
ISO 2022 11 Swi
ISO 2022 11 UK
ISO 2022 11 Dan
ISO 2022 11 Nor
ISO 2022 11 Spa
Swedish Replacement Characters
French/Belgian Replacement Characters
French/Belgian Replacement Characters
German Replacement Characters
Italian Replacement Characters
Swiss Replacement Characters
British Replacement Characters
Danish Replacement Characters
Norwegian Replacement Characters
Spanish Replacement Characters
A - 6
4600rp, 4600g/4600r, 4800i User’s Guide
4600rp, 4600g/4600r, 4800i User’s Guide
A - 7
A - 8
4600rp, 4600g/4600r, 4800i User’s Guide
Sample Symbols
Matrix 2 of 5
RSS-14
6543210
PDF417
(01)00123456789012
Postnet
Car Registration
Zip Code
Code 49
Data Matrix
1234567890
QR Code
Test Symbol
Numbers
4-CB (4-State Customer Barcode)
01,234,567094,987654321,01234567891
ID-tag (UPU 4-State)
J18CUSA8E6N062315014880T
4600rp, 4600g/4600r, 4800i User’s Guide
Sample Symbols
Aztec
Micro PDF417
Package Label
MaxiCode
Test Message
OCR-B with Modulo 10
check character
Test Message
OCR-A with Modulo 36
check character
4600rp, 4600g/4600r, 4800i User’s Guide
OCR Programming Chart
T
O
A
D
Discard
Save
4600rp, 4600g/4600r, 4800i User’s Guide
Hand Held Products, Inc.
700 Visions Drive
P.O. Box 208
Skaneateles Falls, NY 13153-0208
46gr-48i-UG Rev D
3/08
|
