NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
IRON GRIP STRENGTH
SMITH MACHINE
TSA 5000
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
TSA 5000
Retain This
Manual for
Reference
08-31-05
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.
IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL PLACEMENT
The warning labels shown here have been placed on the Front Stabilizer and Upper Frame. If
the labels are missing or illegible, please call customer service at 1-800-888-8899 for
replacements. Apply the labels in the location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE HARDEWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE HARDEWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Connect the two Base Frames (#1) by a Cross Brace (#2) in the mid-span. Secure
each end of The Cross Brace with two M10 x 3 ½” Carriage Bolts (#79), one 4 ¾” x
2” Bracket (#36), two Ø ¾” Washers (#66), and two M10 Aircraft Nuts (#86).
B.) NOTE: DO NOT tighten the Nuts and Bolts yet.
DIAGRAM 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the right Front Vertical Frame (#3) to the right Base Frame (#1). Secure it
with two M10 x 3” Carriage Bolts (#76), one 5 1/8” x 2 ¾” Bracket (#34), two Ø ¾”
Washers (#66), and two M10 Aircraft Nuts (#86). Do not tighten the Nuts and Bolts
yet.
B.) Align a Ø 2 ½” Rubber Bumper (#59) to the hole on the Base Frame. Insert a Guide
Rod (#25) through the Rubber Bumper and into the Base Frame. Secure it with one
M10 x 1” Allen Bolt (#68) and Ø ¾” Washer (#66).
C.) Slide a Lower Safety Stop Frame (#92) onto the Guide Rod (#25). Attach a Safety
Hook (#93) to the Lower Safety Stop Frame. Secure it with one M10 x 1” Allen Bolt
(#68) and M10 Aircraft Nut (#86).
D.) Slide a Safety Stop Frame (#26) onto the Guide Rod (#25).
E.) Attach the hole on top of the Right Vertical Frame (#5) to the top of the Guide Rod
(#25). Attach the top of Right Vertical Frame (#5) to the top of Front Vertical Frame
(#3). Attach the bottom of Right Vertical Frame (#5) to the Base Frame (#1).
F.) Secure the Guide Rod (#25) to the Right Vertical Frame (#5) with one M10 x 1”
Allen Bolt (#68) and Ø ¾” Washer (#66). Secure the Right Vertical Frame (#5) to the
Base Frame with two M10 x 3” Carriage Bolts (#76), one 6 ¼” x 2” Bracket (#37),
two Ø ¾” Washers (#66), and two M10 Aircraft Nuts (#86). Do not tighten the Nuts
and Bolts yet.
G.)Secure the Right Vertical Frame (#5) to the Front Vertical Beam (#3) with one
Triangle Bracket (#33), M10 x 3 1/8” Allen Bolt (#72), and ∅3/4” Washer (#66) to the
top hole. Secure the bottom two holes with two M10 x 3 3/8” Carriage Bolts (#78),
∅3/4” Washers (#66) and M10 Aircraft Nuts (#86).
H.) Repeat the above Procedures A, B, C, D, E, F and G to install the other side.
I.) Attach the Front Top Beam (#15) to the Front Vertical Beams (#3) and the Triangle
Brackets (#33). Align the Holes. Secure each end with two M10 x 3 3/8” Carriage
Bolts (#78), Ø3/4” Washers (#66), and M10 Aircraft Nuts (#86).
J.) Securely tighten all Nuts and Bolts previously installed.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Rear Vertical Beam (#6) to the top of the Cross Brace (#2). Attach the Weight
Glide Base (#8) to the Cross Brace from the Bottom. Align the holes. Secure them with
two M10 x 3” Carriage Bolts (#76), Ø ¾” Washers (#66), and M10 Aircraft Nuts (#86).
B.) Attach the Backrest Board (#38) to the Rear Vertical Beam. Secure it with two M8 x 2 ½”
Allen Bolts (#80) and Ø 5/8” Washers (#65).
DIAGRAM 3
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Weight Glide Post (#7) to the Weight Glide Base (#8). Secure it with four M10 x
1” Carriage Bolts (#74), Ø ¾” Washers (#66) and M10 Aircraft Nuts (#86).
B.) Slide the Sliding Weight Post (#14) onto the Post from the top. Place the Upper Frame (#9)
onto the Weight Glide Post (#7), Rear Vertical Beam (#6) and Front Top Beam (#15).
C.) Align the holes. Secure the Upper Frame (#9) to the Weight Glide Post (#7) with two M10 x
3” Allen Bolts (#71), four Ø ¾” Washers (#66), and two M10 Aircraft Nuts (#86). Do not
tighten the Nuts and Bolts yet.
D.) Secure the Upper Frame to the Rear Vertical Beam with two M10 x 2 ¾” Carriage Bolts
(#75), ∅ ¾” Washers (#66) and M10 Aircraft Nuts (#86).
E.) Secure the Upper Frame to the Front Top Beam with two M10 x 3 1/8” Carriage Bolts (#77),
one 5 1/8” x 2 3/8” Bracket (#35), two Ø ¾” Washers (#66), and two M10 Aircraft Nuts
(#86). Securely tighten all Nuts and Bolts previously installed.
DIAGRAM 4
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Butterfly Base (#12) to the front of Rear Vertical Frame (#6). Attach the Butterfly
Pulley Bracket (#13) to the back of the Rear Vertical Frame. Align the holes. Secure them
with two M10 x 2 ¾” Carriage Bolts (#75), Ø ¾” Washers (#66), and M10 Aircraft Nuts
(#86).
B.) Attach the Right Butterfly (#11) to the hole on the Butterfly Base. Secure it with one Lock
Ring (#56), Ø 1 ½” Washer (#67), M6 x 1 5/8” Allen Bolt (#83), and M6 Aircraft Nut (#85).
C.) Attach the Butterfly Arm Pad (#39) to the Right Butterfly. Secure it with two M8 x 2 ½” Allen
Bolts (#80) and Ø 5/8” Washers (#65).
D.) Repeat the Procedures B & C above to install the other side.
E.) Insert two Swivel Pulley Brackets (#20) into the holes on the Butterfly Pulley Bracket (#13).
Secure each Swivel Pulley Bracket with one Ø ¾” Washer (#66) and M10 Aircraft Nut
(#86). Do not over tighten the Nut. Make sure the Bracket is able to swivel.
DIAGRAM 5
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6 & Cable Loop)
A.) Attach the 128” Upper Cable (#41) to the front opening on the Upper Frame (#9). Attach a
Pulley (#57) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#70), two Pulley Bushings
(#62), and one M10 Aircraft Nut (#86). Make sure the ball stopper of the Cable is underneath
the Frame.
B.) Draw the Cable over the Pulley along the Upper Frame to the opening on the rear of Upper
Frame. Attach a Pulley to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#70), two
Pulley Bushings (#62), and one M10 Aircraft Nut (#86).
C.) Draw the Cable around the Pulley then downward. Install a Pulley in between the Double
Floating Pulley Bracket (#18). Secure the Pulley with one M10 x 1 ¾” Allen Bolt (#69), two Ø ¾”
Washers (#66), and one M10 Aircraft Nut (#86). Let the Bracket hanging for now.
D.) Draw the Cable around the Pulley then up to the open bracket on the top of the Weight Glide
Post (#7). Attach a Pulley to the bracket. Secure it with one M10 x 3” Allen Bolt (#71), two Ø ¾”
Washers (#66), and one M10 Aircraft Nut (#86).
E.) Draw the Cable around the Pulley then down to the Sliding Weight Post (#14). Secure the Cable
to the Sliding Weight Post with one M10 x 1” Allen Bolt (#68), two Ø ¾” Washers (#66), and one
M10 Aircraft Nut (#86).
F.) Connect the Lat Bar (#29) to the Upper Cable with a Short Chain (#63) and two C-Clips (#61).
G.)Attach two Olympic Sleeves (#43) to the weight posts on the Sliding Weight Post. Attach two
Spring Clips (#60) to the Sleeves.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7 & Cable Loop)
A.) Attach one end of the 87” Butterfly Cable to the clip on the Right Butterfly (#11). Draw
the Cable to the right Swivel Pulley Bracket (#20).
B.) Attach a Pulley (#57) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#69),
two Ø ¾” Washers (#66), and one M10 Aircraft Nut (#86).
C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single
Floating Pulley Bracket (#19). Repeat Procedure B above to install a Pulley. Let the
Bracket hanging for now.
D.) Draw the Cable upward to the left Swivel Pulley Bracket. Repeat Procedure B above
to install another Pulley.
E.) Draw the Cable around the Pulley they clip it to the Left Butterfly.
DIAGRAM 7
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8 & Cable Loop)
A.) Attach the 128” Lower Cable (#40) to the opening on the bottom of the Rear Vertical Beam
(#6). Attach a Pulley to the opening. Attach two Pulley Bushings (#62) to the holes outside of
the opening. Attach the Foot Plate (#16) to the Bushings. Align the holes and secure them
with one M10 x 3 3/8” Allen Bolt (#73), two Ø ¾” Washers (#66), and one M10 Aircraft Nut
(#86).
B.) Draw the Cable underneath the Pulley to the open bracket on the Weight Glide Base (#8).
Install a Pulley with a M10 x 1 ¾” Allen Bolt (#69), two ∅ ¾” Washers (#66) and one M10
Aircraft Nut (#86). Draw the Cable around the Pulley then upward to the Double Floating
Pulley Bracket (#18) previously installed in Step-6. Install another Pulley.
C.) Draw the Cable around the Pulley then downward to the open bracket on the Rear Vertical
Beam. Install another Pulley.
D.) Draw the Cable around the Pulley and upward to the Single Floating Pulley Bracket
previously installed in Step-7. Connect the Cable to a Short Chain (#63) by using a C-clip
(#61). Attach the Short Chain to the Bracket. Secure it with a M10 x 1” Allen Bolt (#68), two
Ø ¾” Washers (#66), and one M10 Aircraft Nut (#86). Adjust the tension of the Cable by
adjusting the length of the Chain.
E.) Secure the Foot Plate (#16) to the Weight Glide Base (#8) with two M10 x 1” Allen Bolts
(#68), four Ø ¾” Washers (#66), and two M10 Aircraft Nuts (#86).
F.) Connect the Long Chain (#64) to the Lower Cable with a C-clip. For various exercises,
connect with one of the Shiver Bar (#30), V Bar (#88), Ankle Strap (#89), Single Handle
Strap (#90), or the Triceps Rope (#91) with a C-clip.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 8
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9 (See Diagram 9)
A.) NOTE: Help of another person is strongly recommended for this step. Place the
Lifting Sleeve (#27) in between the two Safety Stop Frames (#26). Align the holes.
Insert the Weight Bar (#28) into the Safety Stop Frame from one end and through the
Lifting Sleeve (#27) to the other Safety Stop Frame on the opposite side. Secure the
Weight Bar to each Safety Stop Frame with a M8 x 3/8” Allen Bolt (#81).
B.) Turn the safety catch hook forward on the Lifting Sleeve to secure its position on the
selected holes on the Front Vertical Frames (#3).
C.) Attach a Long Olympic Sleeve (#44) to each end of the Weight Bar. Attach a Spring
Clip (#60) to the Sleeve.
D.) Attach six Weight Posts (#17) to the Left & Right Vertical Frames (#4&5). Secure
each Weight Post with two M10 x 2 ¾” Carriage Bolts (#75), one 4 ¾” x 2” Bracket
(#36), two Ø ¾” Washers (#66), and two M10 Aircraft Nuts (#86).
E.) Attach six Olympic Sleeves (#43) to the six Weight Posts. Attach six Spring Clips
(#60) to the Sleeves.
F.) Insert the Left & Right Bar Holders (#21&22), the Left & Right Safety Catches
(#23&24) into the selected holes on the Front Vertical Frames (#3).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DIAGRAM
18
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
9
Base Frame
Cross Brace
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
6
1
1
2
1
1
1
1
2
2
1
1
1
1
1
2
2
2
1
8
2
1
2
1
1
1
8
2
2
2
2
2
2
7
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
2 3/8” Square End Cap
2 ¾” x 2” End Cap
Ø 1” Cone-shaped End Cap
2 3/8” x 2” Sleeve
Sliding Sleeve
Lock Ring
Pulley
Ø 1 ¾” Rubber Bumper
Ø 2 ½” Rubber Bumper
Spring Clip
C-Clip
Pulley Bushing
Short Chain
Long Chain
Ø 5/8” Washer
Ø ¾” Washer
Ø 1 ½” Washer
M10 x 1” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 2 ½” Allen Bolt
M10 x 3” Allen Bolt
M10 x 3 1/8” Allen Bolt
M10 x 3 3/8” Allen Bolt
M10 x 1” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M10 x 3” Carriage Bolt
M10 x 3 1/8” Carriage Bolt
M10 x 3 3/8” Carriage Bolt
M10 x 3 ½” Carriage Bolt
M8 x 2 ½” Allen Bolt
M8 x 3/8” Allen Bolt
M6 x 5/8” Philips Screw
M6 x 1 ¼” Allen Bolt
Chrome Panel Screw
M6 Aircraft Nut
M10 Aircraft Nut
Ø 1” End Cap
V Bar
Ankle Strap
Single Handle Strap
Triceps Rope
Lower Safety Stop Frame
Safety Hook
2
1
12
2
4
2
11
1
2
10
5
6
2
1
6
82
2
10
7
2
3
2
1
4
16
10
2
8
4
6
4
1
2
8
2
65
6
1
Front Vertical Beam
Left Vertical Frame
Right Vertical Frame
Rear Vertical Beam
Weight Glide Post
Weight Glide Base
Upper Frame
10 Left Butterfly
11 Right Butterfly
12 Butterfly Base
13 Butterfly Pulley Bracket
14 Sliding Weight Post
15 Front Top Beam
16 Foot Plate
17 Weight Post
18 Double Floating Pulley Bracket
19 Single Floating Pulley Bracket
20 Swivel Pulley Bracket
21 Left Bar Holder
22 Right Bar Holder
23 Left Safety Catch
24 Right Safety Catch
25 Guide Rod
26 Safety Stop Frame
27 Lifting Sleeve
28 Weight Bar
29 Lat Bar
30 Shiver Bar
31 Curl Handle
32 Chrome Panel
33 Triangle Bracket
34 5 1/8” x 2 ¾” Bracket
35 5 1/8” x 2 3/8” Bracket
36 4 ¾” x 2” Bracket
37 6 ¼” x 2” Bracket
38 Backrest Board
39 Butterfly Arm Pad
40 128” Lower Cable
41 128” Upper Cable
42 87” Butterfly Cable
43 Olympic Sleeve
44 Long Olympic Sleeve
45 Curl Bar Handle Grip
46 Lat Bar Grip
1
1
1
2
2
4
1
1
Sliding Bearing
#6 Allen Wrench (Tool)
#5 Allen Wrench (Tool)
#4 Allen Wrench (Tool)
47 Ø 1” x 3 1/8” Bushing
48 Ø 1 ½” x 1” Bushing
49 1 ½” Square End Cap
50 1 ¾” Square End Cap
1
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTIPURPOSE BENCH HARDWARE PACK
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTIPURPOSE BENCH ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended this machine be assembled by two or
more people to avoid possible injury.
STEP 1 (See Diagram 1)
C.) Attach the Main Frame (#1) to the Front & Rear Stabilizers (#2 & 3). Secure each end with
two M10 x ¾” Allen Bolts (#36) and ∅ ¾” Washers (#42). Attach a Lock Knob (#23) to the
hole underneath the Main Frame.
D.) Slide the Sliding Block (#8) onto the Incline Adjustment Bar (#9). Align the hole then secure
it with a Knob Lock (#23) to hold the Sliding Block in position.
E.) Attach the Incline Adjustment Bar to the brackets on the Main Frame. Secure each end with
one M10 x 2 ½” Carriage Bolt (#35), ∅ ¾” Washer (#42), and M10 Aircraft Nut (#44).
DIAGRAM 1
21
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach four Bushings (#27) to a Seat Support Frame (#6).
B.) Attach a Backrest Support (#7) to the rear of the Seat Support Frame (#6). Align the holes and
secure them with one M10 x 1 ¾” Allen Bolt (#37) and ∅ ¾” Washer (#42). Repeat the same
procedure to install the other side.
C.) Attach two Bushings to the pivot on the Sliding Block (#8). Attach two Bushings to each Backrest
Supports (#7). Align the holes and secure them with one M10 x 6 ¾” Allen Bolt (#38), two ∅ ¾”
Washers (#42), and one M10 Aircraft Nut (#44). Do not over tighten the nut and bolt. The
Supports need to swivel on the Bolt.
D.) Attach two Bushings to the pivot on the Main Frame (#1). Loosen and pull the Lock Knob on the
Sliding Block (#8). The Sliding Block needs to be able to slide on the Chromed Incline
Adjustment Bar (#9). Align the two Seat Support Frames (#6) to both ends of the pivot on Main
Frame. Secure them with one M10 x 8 ¼” Allen Bolt (#39), two ∅ ¾” Washers (#42), and one
M10 Aircraft Nut (#44).
E.) Use the Lock Knob on the Sliding Block (#8) to adjust and secure the backrest incline position.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
C.) Place the Backrest Board (#14) onto the Backrest Supports (#7). Secure it with
four M8 x 2” Allen Bolts (#40) and ∅ 5/8” Washers (#43).
D.) Place the Seat Pad (#13) onto the Seat Support Frames (#6). Secure it with four
M8 x 2” Allen Bolts (#40) and ∅ 5/8” Washers (#43).
DIAGRAM 3
23
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it with
an Axle (#17), two M10 x ¾” Allen Bolts (#36), and two ∅ ¾” Washers (#42).
B.) Insert one Foam Tube (#10) halfway through the hole on the Main Frame. Insert two Foam
Tubes halfway through the holes on the Leg Developer (#5). Push six Foam Rolls (#24)
onto the Tubes from both ends. Plug six Foam Roll End Caps (#25) into the Tubes.
C.) Slide the Olympic Sleeve (#20) onto the weight post on the Leg Developer. Attach a Spring
Clip (#22) to the Sleeve.
DIAGRAM 4
24
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Arm Curl Pad (#15) to the Arm Curl Stand (#4). Secure it with two M8 x 5/8”
Allen Bolts (#41) and two ∅ 5/8” Washers (#43). Insert the Arm Curl Stand into the front
opening on the Main Frame (#1). Use the Lock Knob to hold the desired Arm Curl height.
B.) Attach the Curl Bar Support Frame (#11) to the open bracket on the Leg Developer (#5).
Lock it with a L-shaped Pin (#21).
C.) Remove the Pin, Curl Bar Handle and Arm Curl when using the Leg Developer to exercise.
DIAGRAM 5
25
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTIPURPOSE BENCH PARTS LIST
KEY NO.
1
DESCRIPTION
Main Frame
Q’ty
1
2
Front Stabilizer
1
3
Rear Stabilizer
1
4
5
Arm Curl Stand
Leg Developer
1
1
6
7
8
Seat Support Frame
Backrest Support
Sliding Block
2
2
1
9
Incline Adjustment Bar
Foam Tube
1
3
10
11
12
13
14
15
16
17
18
19
20
21
23
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Curl Bar Support Frame
Curl Bar Handle
Seat Pad
Backrest Board
Arm Curl Pad
1
1
1
1
1
2
1
2
2
1
1
1
2
6
6
2
16
1
1
1
2
12
3
4
2
6
Curl Bar Handle Grip
Axle
Ø 2 3/8” Bushing
Ø 1 ½” Bushing
Olympic Sleeve
L-shaped Lock Pin
Spring Clip
Lock Knob
Foam Roll
Foam Roll End Cap
Ø ¾” x ½” Bushing
Bushing
3 1/8” x 1 5/8” End Cap
Ø 1” Cone-shaped End Cap
Ø 1” End Cap
1 5/8” x 2 3/8” End Cap
1 5/8” x ¾” End Cap
2” Sliding Block Sleeve
Stabilizer End Cap
M10 x 2 ½” Carriage Bolt
M10 x ¾” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 6 ¾” Allen Bolt
M10 x 8 ¼” Allen Bolt
M8 x 2” Allen Bolt
M8 x 5/8” Allen Bolt
Ø ¾” Washer
2
1
1
8
2
14
10
4
Ø 5/8” Washer
M10 Aircraft Nut
27
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing
or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.Model
2.Description of Parts
3.Part Number
4.Date of Purchase
28
Download from Www.Somanuals.com. All Manuals Search And Download.
|