NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY SMITH MACHINE
MXM-5
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MXM-5
Retain This
Manual for
Reference
09-01-05
OWNER'S
MANUAL
IMPEX
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire
manual before you assemble or operate your machine. In particular, note the following
safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL REPLACEMENT
The warning labels shown here have been placed on the Cross Brace and Upper Frame. If the
labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements.
Apply the labels in location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDEWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDEWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDEWARE PACK
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDEWARE PACK
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) NOTE: Do not tighten the Nuts and Bolts until instructed to do so.
B.) Connect the Left & Right Base Frames (#17 & #18) by a Cross Brace (#20) in the mid-
span. Secure each end of the Cross Brace with two M10 x 2 ½” Carriage Bolts (#92), one
4 3/8” x 1 ¾” Bracket (#46), two Ø ¾” Washers (#82), and two M10 Aircraft Nuts (#99).
C.) Attach a Front Vertical Beam (#16) to the Left Base Frame (#17). Secure it with two M10 x
2 ¾” Carriage Bolts (#93), one 4 ¾” x 2” Bracket (#47), two Ø ¾” Washers (#82), and two
M10 Aircraft Nuts (#99). Repeat the same procedure to install the other side.
D.) Attach the Front Top Beam (#32) to the two Front Vertical Beams. Secure each end with
one M10 x 2 ½” Allen Bolt (#89), 4” x 2” Bracket (#45), and Ø ¾” Washer (#82) into the top
hole. Secure the bottom hole with one M10 x 2 ¾” Carriage Bolt (#93), Ø ¾” Washer
(#82), and M10 Aircraft Nut (#99).
E.) Insert a Guide Rod (#19) into the hole on the Left Base Frame (#17). Secure it with one
M10 x 1” Allen Bolt (#85) and ∅ ¾” Washer (#82) at the bottom.
F.) Slide a Lower Safety Stop Frame (#42) and a Safety Stop Frame (#37) onto the Guide
Rod (#19).
G.) Secure the top of the Guide Rod with one M10 x 1” Allen Bolt (#85) and ∅ ¾” Washer
(#82).
H.) Attach a Safety Hook (#43) to the Lower Safety Stop Frame (#42). Secure it with one M10
x 1” Allen Bolt (#85), two ∅ ¾” Washers (#82), and one M10 Aircraft Nut (#99).
I.) Attach the Safety Hook to the selected hole on the Front Vertical Beam.
J.) Repeat procedures E through I above to install the other side.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Rear Vertical Beam (#23) onto the Cross Brace (#20). Attach the Weight Glide
Post (#22) to the Rear Vertical Beam and Cross Brace. Align the holes and secure them
with two M10 x 2 ¾” Carriage Bolts (#93), ∅ ¾” Washers (#82), and M10 Aircraft Nuts
(#99).
B.) Slide the Sliding Weight Post (#34) onto the Weight Glide Post (#22).
C.) Place the Upper Frame (#21) onto the Rear Vertical Beam (#23), Weight Glide Post (#22),
and Front Top Beam (#32).
D.) Secure the Upper Frame to the Weight Glide Post (#22) with two M10 x 2 3/8” Allen Bolts
(#88), four ∅ ¾” Washers (#82), and two M10 Aircraft Nuts (#99).
E.) Secure the Upper Frame to the Rear Vertical Beam (#23) with two M10 x 2 3/8” Carriage
Bolts (#91), ∅ ¾” Washers (#82), and M10 Aircraft Nuts (#99).
F.) Secure the Upper Frame to the Front Top Beam (#32) with two M10 x 2 ¾” Carriage Bolts
(#93), one 4 ¾” x 2” Bracket (#47), two ∅ ¾” Washers (#82), and two M10 Aircraft Nuts
(#99).
G.)Push two Olympic Sleeves (#59) onto the weight posts on the Sliding Weight Post (#34).
Attach a Spring Clip (#76) to each Sleeve.
H.) Securely tighten all nuts and bolts previously installed.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Butterfly Base (#24) and Butterfly Pulley Bracket (#33) to the Rear Vertical Beam
(#23). Align the holes and secure them with two M10 x 2 ½” Carriage Bolts (#92), ∅ ¾”
Washers (#82), and M10 Aircraft Nuts (#99).
B.) Insert the pivot on the Right Butterfly (#26) through the hole on the Butterfly Base. Secure it
with one Lock Ring (#73), M6 x 1 ¼” Allen Screw (#100), and M6 Aircraft Nut (#101).
C.) Push a Butterfly Arm Pad (#49) onto the Right Butterfly.
D.) Repeat Procedures B and C above to install the other side.
E.) Attach the Backrest Board (#48) to the Rear Vertical Beam. Secure it with two M8 x 2 3/8”
Allen Bolts (#97) and ∅ 5/8” Washers (#81).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Note: Help of another person is strongly recommended for this step. Place the Weight Lifting
Sleeve (#38) in between the two Safety Stop Frames (#37). Align the holes and insert the
Weight Bar (#39) into the Safety Stop Frame from one end through the Weight Lifting Sleeve
to the other Safety Stop Frame on the opposite end. Secure the Weight Bar to each Safety
Stop Frame with a M8 x 3/8” Allen Bolt (#103).
B.) Turn the safety hook on the Weight Lifting Sleeve to secure its position on the selected holes
on the Front Vertical Beams. Slide two Long Olympic Sleeves (#60) onto the Weight Bar.
Attached two Spring Clips (#76) to the Olympic Sleeves.
C.) Attach four Weight Posts (#27) to the Left & Right Base Frames (#17 & #18). Secure each
Post with one M10 x 1” Allen Bolt (#85) and ∅ ¾” Washer (#82).
D.) Attach four Olympic Sleeves (#59) to the Posts. Attach a Spring Clip (#76) to each Sleeve.
E.) Insert the Left & Right Bar Holders (#28 & #29), Left & Right Safety Catches (#30 & #31) into
the selected holes on the two Front Vertical Beams (#16).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach a 124” Cable (#51) to the front opening on the Upper Frame (#21). Attach a Pulley
(#74) to the opening. Secure it with one M10 x 2 1/8” Allen Bolt (#87), two Ø 7/8”
Bushings (#79), and one M10 Aircraft Nut (#99). Make sure the ball stopper of the Cable
is underneath the Upper Frame.
B.) Draw the Cable over the Pulley along the Upper Frame to the opening on the rear of
Upper Frame. Attach a Pulley to the opening. Secure it with one M10 x 2 1/8” Allen Bolt
(#87), two Ø 7/8” Bushings (#79), and one M10 Aircraft Nut (#99).
C.) Draw the Cable around the Pulley then downward. Install a Pulley in between the two
Double Floating Pulley Brackets (#35). Secure the Pulley with one M10 x 1 ¾” Allen Bolt
(#86), two Ø ¾” Washers (#82), and one M10 Aircraft Nut (#99). Let the Brackets
hanging for now.
D.) Draw the Cable around the Pulley then upward to the open bracket on the top of Weight
Glide Post (#22). Attach a Pulley to the opening. Secure it with one M10 x 2 3/8” Allen
Bolt (#88), two Ø ¾” Washers (#82), and one M10 Aircraft Nut (#99).
E.) Draw the Cable around the Pulley then downward to the Sliding Weight Post (#34).
Secure the Cable to the Sliding Weight Post with one M10 x 1” Allen Bolt (#85), two Ø ¾”
Washers (#82), and one M10 Aircraft Nut (#99).
F.) Connect the Lat Bar (#40) to the Cable with a Chain (#80) using two C-clips (#77).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 5
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Attach one end of the 79” Butterfly Cable (#52) to the clip on the Left Butterfly (#25). Draw the
Cable to the left Butterfly Pulley Bracket (#33).
B.) Attach a Pulley (#74) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#86), two ∅ ¾”
Washers (#82), and one M10 Aircraft Nut (#99).
C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single Floating Pulley
Bracket (#36). Install a Pulley to the Bracket. Let the Bracket hanging for now.
D.) Draw the Cable around the Pulley then upward to the right Butterfly Pulley Bracket. Install
another Pulley. Draw the Cable around the Pulley then clip to Right Butterfly (#26).
DIRGARM 6
17
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach one 124” Cable (#51) to the lower opening on the Rear Vertical Beam (#23). Attach
a Pulley to the opening. Secure it with M10 x 2 3/8” Allen Bolt (#88), two Ø 1” Bushings
(#78), and one M10 Aircraft Nut (#99).
B.) Draw the Cable underneath the Pulley to the open bracket on the Weight Glide Post (#22).
Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#86), two ∅ ¾”
Washers (#82), and one M10 Aircraft Nut (#99).
C.) Draw the Cable around the Pulley then upward to the Double Floating Pulley Bracket
installed in Step-5. Install a Pulley.
D.) Draw the Cable around the Pulley then downward to the open bracket on the back of Rear
Vertical Beam. Install a Pulley then draw the Cable upward to the Single Floating Pulley
Bracket installed in Step-6. Secure the end of the Cable to the bracket with M10 x 1” Allen
Bolt (#85), two ∅ ¾” Washers (#82), and one M10 Aircraft Nut (#99).
E.) Connect the Shiver Bar (#41) to the Cable with a Chain (#80) using two C-clips (#77).
F.) Check the tension of the Cables. If the Cables are too loose, adjust the tension by moving
up the Pulley on the Double Floating Pulley Bracket (#35). If the Tension is too tight, then
move down the Pulley.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8)
A.) Attach the Main Seat Support (#1) to the Front & Rear Stabilizers (#3 & #4).
B.) Secure each end with two M10 x 3 1/8” Carriage Bolts (#94), one 4 ¾” Curve Bracket
(#8), two ∅ ¾” Washers (#82), and two M10 Aircraft Nuts (#99).
DIAGRAM 8
19
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9 (See Diagram 9)
A.) Do not tighten all nuts and bolts until instructed to so.
B.) Attach the Leg Developer Holder (#2) to the Main Seat Support. Secure it with two M10 x 3
1/8” Carriage Bolts (#94), one 6 ¼” Curve Bracket (#9), two ∅ ¾” Washers (#82), and two
M10 Aircraft Nuts (#99).
C.) Attach the Backrest Supports (#5) to the bracket on the Main Seat Support. Attach the seat
support on the Leg Developer Holder (#2) to the inside of the open bracket. Align the holes
and secure them together with a M12 x 8” Hex Bolt (#84), two ∅ 1” Washers (#83), and one
M12 Aircraft Nut (#102).
D.) Attach the Backrest Incline Support (#6) to the Backrest Supports (#5). Align the holes and
secure them with one M12 x 8” Hex Bolt (#84), two ∅ 1” Washers (#83), and one M12
Aircraft Nut (#102).
E.) Securely tighten all nuts and bolts previously installed. Make sure the Backrest Supports and
the Backrest Incline Support are able to swivel.
F.) Place the Backrest Board (#11) onto the Backrest Supports (#5). Secure it with four M8 x 1
5/8” Allen Bolts (#95) and Ø 5/8” Washers (#81).
G.)Place the Seat Pad (#10) onto the Leg Developer Holder (#2). Secure it with four M8 x ¾”
Allen Bolts (#96) and Ø 5/8” Washers (#81).
20
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP-10 (See Diagram 10)
A.) Attach the Leg Developer (#7) to the Leg Developer Holder (#2). Secure it with one M10 x
3 1/8” Allen Bolt (#90), two ∅ ¾” Washers (#82), and one M10 Aircraft Nut (#99). Do not
over tighten the nut and bolt. Make sure the Leg Developer is able to swivel.
B.) Insert three Foam Tubes (#15) halfway through the holes on the Leg Developer Holder and
Leg Developer. Push six Foam Rolls (#53) onto the Tubes. Plug six Foam Roll End Caps
(#55) into the Tubes.
C.) Attach an Olympic Sleeve (#59) onto the weight post on the Leg Developer. Attach a
Spring Clip (#76) to the Sleeve.
D.) Attach a Curl Bar Holder Frame (#108) to the Leg Developer. Secure it with a L-shaped
Pin (#107).
DIAGRAM 10
21
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP-11 (See Diagram 11)
A.) Attach the Arm Curl Pad (#14) to the Arm Curl Stand (#13). Secure it with two M8 x ¾”
Allen Bolts (#96) and ∅ 5/8” Washers (#81).
B.) Insert the Arm Curl Stand into the opening on the Leg Developer Holder. Use a Lock
Knob (#58) to secure it in position. Remove the Arm Curl Stand and Curl Bar Holder
Frame when doing leg exercises.
DIAGRAM 11
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE EXPLODED DIAGRAM
23
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
9
Main Seat Support
Leg Developer Holder
Front Stabilizer
1
1
1
1
2
1
1
2
1
1
1
6
1
1
3
2
1
1
2
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
2
1
2
1
1
1
1
2
2
1
2
2
3
1
2
2
2
1
6
2
6
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
Ø 2 3/8” End Cap
2” x 1 ¾” Sleeve
Lock Knob
Olympic Sleeve
Long Olympic Sleeve
5” Grip
∅ 1 1/8” Bushing
Ø 1 ½” x 1” Washer
1 ½” Square End Cap
1 ¾” Square End Cap
2” Square End Cap
1 5/8” x 2 3/8” End Cap
∅ 2” End Cap
∅ 1” Cone-shaped End Cap
∅ 1” End Cap
1 ¾” x 1 ½” Sleeve
1 ½” x 1” Sleeve
Lock Ring
4
1
1
7
2
4
4
2
2
6
2
1
2
7
7
2
8
2
11
1
9
4
2
4
Rear Stabilizer
Backrest Support
Backrest Incline Support
Leg Developer
4 ¾” Curve Bracket
6 ¼” Curve Bracket
10 Seat Pad
11 Bench Backrest Board
12 Ø 1” Spacer
13 Arm Curl Stand
14 Arm Curl Pad
15 Foam Tube
16 Front Vertical Beam
17 Left Base Frame
18 Right Base Frame
19 Guide Rod
20 Cross Brace
21 Upper Frame
22 Weight Glide Post
23 Rear Vertical Beam
24 Butterfly Base
25 Left Butterfly
26 Right Butterfly
Pulley
∅ 1 ¾” Rubber Bumper
Spring Clip
C-clip
∅ 1” Bushing
Ø 7/8” Bushing
Chain
2
∅ 5/8” Washer
16
64
4
2
12
7
2
4
2
1
2
6
10
6
4
12
2
1
42
2
2
27 Weight Post
∅ ¾” Washer
28 Left Bar Holder
29 Right Bar Holder
30 Left Safety Catch
31 Right Safety Catch
32 Front Top Beam
33 Butterfly Pulley Bracket
34 Sliding Weight Post
35 Double Floating Pulley Bracket
36 Single Floating Pulley Bracket
37 Safety Stop Frame
38 Lifting Sleeve
39 Weight Bar
40 Lat Bar
41 Shiver Bar
42 Lower Safety Stop Frame
43 Safety Hook
44 Shiver Bar Handle
45 4” x 2” Bracket
46 4 3/8” x 1 ¾” Bracket
47 4 ¾” x 2” Bracket
48 Backrest Board
49 Butterfly Arm Pad
50 1 5/8” x ¾” End Cap
51 124” Cable
52 79” Butterfly Cable
53 Foam Roll
54 1” Square End Cap
55 Foam Roll End Cap
∅ 1” Washer
M12 x 8” Allen Bolt
M10 x 1” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 2 1/8” Allen Bolt
M10 x 2 3/8” Allen Bolt
M10 x 2 ½” Allen Bolt
M10 x 3 1/8” Allen Bolt
M10 x 2 3/8” Carriage Bolt
M10 x 2 ½” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M10 x 3 1/8” Carriage Bolt
M8 x 1 5/8” Allen Bolt
M8 x ¾” Allen Bolt
M8 x 2 3/8” Allen Bolt
M6 x 5/8” Philips Screw
M10 Aircraft Nut
M6 x 1 ¼” Allen Screw
M6 Aircraft Nut
M12 Aircraft Nut
M8 x 3/8” Allen Bolt
Ankle Strap
Single Handle
∅ ½” Bushing
L-shaped Pin
2
4
1
1
2
1
1
Curl Bar Holder Frame
25
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX
LIMITED WARRANTY
IMPEX warrants this product to be free from defects in workmanship and material, under normal use and
service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends
only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at
IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.Model
2.Description of Parts
3.Part Number
4.Date of Purchase
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|