NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY HOME GYM
MWM 800
Hardware Identifier
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM 800
Retain This
Manual for
Reference
08-20-02
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave
children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to properly
warm up.
11. Never operate the machine if the machine is not functioning properly.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Identifier
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required to Assemble the Machine: Two Adjustable Wrenches, two Allen
Wrenches, and one Flat Head Screwdriver
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Connect the Main Base Frame (#2) and Front Base (#3) to the Front Stabilizer (#5).
Align the holes then secure them with two 3/8” x 3” Carriage Bolts (#69), ∅ 3/8”
Washers (#77), and 3/8” Aircraft Nuts (#74).
B.) Attach the Rear Stabilizer (#1) to the Main Base Frame. Secure it with one Bracket
(#26), two 3/8” x 3” Carriage Bolts (#69), ∅ 3/8” Washers (#77), and 3/8” Aircraft Nuts
(#74).
C.) Attach the Vertical Beam (#4) to the Main Base Frame (#2). Secure it with two 3/8” x 3”
Carriage Bolts (#69), ∅ 3/8” Washers (#77), and 3/8” Aircraft Nuts (#74).
D.) Over the two holes on the Rear Stabilizer (#1), stack up two Round Rubber Bumpers
(#40), two Guide Rod Sleeves (#7), then two Round Rubber Bumpers (#40) in
sequence. Align the holes then insert two Guide Rods (#13) all the way down into the
Rear Stabilizer (#1).
E.) Slide the Weight Holder (#8) from the top onto the two Guide Rods.
F.) Place the Upper Frame (#6) onto the Vertical Beam (#4) and the two Guide Rods (#13).
Secure the Upper Frame to the Guide Rods with two 3/8” x 1” Allen Bolts (#63) and ∅
3/8” Washers (#77). Secure the Upper Frame to the Vertical Beam (#4) with two 3/8” x
3” Carriage Bolts (#69), ∅ 3/8” Washers (#77), and 3/8” Aircraft Nuts (#74).
G.)Attach the Olympic Sleeves (#44) to the Weight Holder (#8). Attach the ∅ 2” Spring
Clips (#48) onto the Olympic Sleeves. Please note that we also provided two ∅1”
Spring Clips in case the ∅1” standard plates were used.
H.) Carefully tip over the machine to its side. Secure the bottom of the two Guide Rods to
the Rear Stabilizer (#1) with two 3/8” x 1” Allen Bolts (#63) and ∅ 3/8” Washers (#77).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Seat Support (#15) to the Vertical Beam (#4). Secure it with one Bracket
(#26), two 3/8” x 3 7/8” Carriage Bolts (#68), ∅ 3/8” Washers (#77), and 3/8” Aircraft Nuts
(#74).
B.) Attach the Seat post (#14) to the Seat Support (#15). Secure it with one Bracket (#26),
two 3/8” x 3” Carriage Bolts (#69), ∅ 3/8” Washers (#77), and 3/8” Aircraft Nuts (#74).
C.) Secure the bottom of the Seat Post (#14) to the Front Base (#3) with one 3/8” x 4 ½”
Carriage Bolt (#67), ∅3/8” Washer (#77) and 3/8” Aircraft Nut (#74).
D.) Insert the Seat Incline Adjustment (#16) into the hole on top of the Seat Post (#14).
Secure it with a quick Release Lock Pin (#45).
E.) Place the Seat Pad (#20) onto the Seat Incline Adjustment (#16). Secure it with two M8 x
1 ½” Allen Bolts (#65) and ∅ ¼” Washers (#76).
F.) Attach a Square Rubber Bumper (#29) onto the front opening on the Seat Support (#15).
Secure it with one M10 x 1” Philips Screw (#70).
G.)Attach the Leg Developer (#17) to the Seat Support (#15). Secure it with one 3/8” x 3”
Allen Bolt (#59), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74).
H.) Insert the Foam Roll Tubes (#27) halfway through the hole on the Seat Incline
Adjustment (#16) and Leg Developer (#17). Push four Foam Rolls (#43) onto the Tubes.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Front Press Lock Pin (#22) to the Vertical Beam (#4). Secure it with one M8 x 2 ½”
Allen Bolt (#64), two ∅ ¼” Washers (#76), and one M8 Aircraft Nut (#73). Plug a 1 ½” Square
End Cap (#35) to the front opening on the Vertical Beam.
B.) Plug two ½” Metal Bushings (#72) onto the side-holes on the Upper Frame (#6). Attach the
Front Press Base (#9) to the Bushings. Secure it with one ½” x 6 1/8” Allen Bolt (#56), two ∅
½” Washers (#78), and one ½” Aircraft Nut (#75). Flip down the Lock Pin (#22) to lock the
Front Press Base for Butterfly exercise only. Flip up the Lock Pin for Front Press exercises.
C.) Plug two ½” Metal Bushings (#72) to the pivot on the Butterfly Bracket (#10). Attach the
Butterfly Bracket to the Front Press Base. Secure it with one ½” x 4 1/8” (#57) Allen Bolt (#57),
two ∅ ½” Washers (#78), and one ½” Aircraft Nut (#75). Repeat the same procedure to install
the other side.
D.) Secure the Backrest Board (#21) to the Vertical Beam (#4) with four M8 x 2 ½” Allen Bolts
(#66) and ∅1/4” Washers (#76).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Plug two ½” Metal Bushings (#72) to the pivot on the Left Butterfly (#12). Attach the Left
Butterfly to the Front Press Base (#9). Secure it with one ½” x 3 1/8” Allen Bolt (#58), two ∅ ½”
Washers (#78), and one ½” Aircraft Nut (#75).
B.) Slide two Foam Grips (#42) onto the Left Butterfly handle.
C.) Repeat Procedures A & B above to install the Right Butterfly (#11).
DIAGRAM 4
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach the 137” Upper Cable (#52) to the open bracket on the front of the Upper
Frame (#6). Note: The Ball Stopper on the cable should be underneath the Frame.
B.) Attach a Pulley (#28) to the bracket and secure it with one 3/8” x 1 ¾” Allen Bolt
(#61), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74).
C.) Draw the Cable to the open slot on the Vertical Beam (#4). Install a Pulley to the
opening. Align the holes and secure it with one 3/8” x 2 5/8” Allen Bolt (#60), two ∅
½” Bushings (#71), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74).
D.) Draw the Cable over the Pulley then downward. Install a Pulley to the Flat Double
Floating Pulley Bracket (#23). Let the Bracket hanging for now. Draw the Cable
around the Pulley then upward to the open bracket on the rear of Upper Frame.
E.) Install another Pulley then pull the Cable downward to the Weight Holder (#8).
Connect the Cable to the Weight Holder with a Hook (#46).
F.) Slide two Handle Grips (#39) onto the Lat Bar (#18). Connect the Lat Bar to the
Upper Cable with two Hooks (#46) and one 12-linked Chain (#50).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Attach one end of the 47” Butterfly Cable (#54) to the left Butterfly Bracket (#10). Secure the
Cable to the Bracket with one 3/8” x 1 3/16” Allen Bolt (#62), ∅ 3/8” Washer (#77), and 3/8”
Aircraft Nut (#74).
B.) Attach a Swivel Pulley Bracket to the Pivot on the Vertical Beam (#4). Secure it with one 3/8”
x 2 5/8” Allen Bolt (#60), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74). Draw
the Cable to the Swivel Pulley Bracket.
C.) Attach a Pulley to the Bracket. Secure it with one 3/8” x 1 ¾” Allen Bolt (#61), two ∅ 3/8”
Washers (#77), and one 3/8” Aircraft Nut (#74).
D.) Draw the Cable over the Pulley then downward. Attach an Angled Double Floating Bracket
(#24). Installed a Pulley as described in Step C. Let the Bracket hanging for now.
E.) Draw the Cable around the Pulley then pull upward. Repeat the steps above to install the
other side.
DIAGRAM 6
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach the 133” Lower Cable (#53) to the opening on the Leg Developer (#17). Attach a Pulley
(#28) to the opening. Secure it with one 3/8” x 2 5/8” Allen Bolt (#60), two ∅ ½” Bushings
(#71), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74).
B.) Draw the Cable underneath the Pulley to the open slot on the Vertical Beam (#4). Install
another Pulley as described in Step A.
C.) Draw the Cable underneath the Pulley then upward to the Angled Double Floating Bracket
(#24) previously installed. Attach a Pulley to the open bracket. Secure it with one 3/8” x 1 ¾”
Allen Bolt (#61), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74).
D.) Draw the Cable around the Pulley the downward to the open bracket on the Main Base Frame
(#2). Install another Pulley.
E.) Draw the Cable around the Pulley then upward to the Flat Double Floating Pulley Bracket
(#23) previously installed. Install another Pulley.
F.) Draw the Cable around the Pulley then connect the Cable to the Main Base Frame with two
Hooks (#46) and a 9-linked Chain (#49).
G.)Adjust the tension of the Cable Loop System by adjusting the length of the Chain.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 7
18
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
19-linked Chain
1
1
1
1
1
1
2
2
1
5
9
2
4
1
2
4
1
2
10
1
6
10
1
30
5
8
51
10
137” Upper Cable
133” Lower Cable
47” Butterfly Cable
Ankle Strap
1
2
3
4
5
6
7
8
Rear Stabilizer
Main Base Frame
Front Base
Vertical Beam
Front Stabilizer
Upper Frame
Guide Rod Sleeve
Weight Holder
Front Press Base
Butterfly Bracket
Right Butterfly
Left Butterfly
Guide Rod
Seat Post
Seat Support
Seat Incline Adjustment
Leg Developer
Lat Bar
Arm Curl Handle
Seat Pad
1
1
1
1
1
1
2
1
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
3
2
12
1
6
4
7
1
4
1
2
2
4
5
4
1
4
4
2
1
7
2
2
1
1
½” x 6 1/8” Allen Bolt
½” x 4 1/8” Allen Bolt
½” x 3 1/8” Allen Bolt
3/8” x 3” Allen Bolt
3/8” x 2 5/8” Allen Bolt
3/8” x 1 ¾” Allen Bolt
3/8” x 1 3/16” Allen Bolt
3/8” x 1” Allen Bolt
M8 x 2 ½” Allen Bolt
M8 x 1 ½” Allen Bolt
M8 x 5/8” Allen Bolt
3/8” x 4 ½” Carriage Bolt
3/8” x 3 7/8” Carriage Bolt
3/8” x 3” Carriage Bolt
M10 x 1” Philips Screw
∅ ½” Bushing
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
½” Metal Bushing
M8 Aircraft Nut
3/8” Aircraft Nut
Backrest Board
Front Press Lock Pin
Flat Double Floating Pulley Bracket
Angled Double Floating Bracket
Swivel Pulley Bracket
Bracket
½” Aircraft Nut
∅ ¼” Washer
∅ 3/8” Washer
∅ ½” Washer
Foam Roll Tube
Pulley
Square Rubber Bumper
∅ 1” Round End Cap
∅ 1 3/8” Round End Cap
2” Square End Cap
1 ¾” Square End Cap
1” x 2” End Cap
1 ½” Square End Cap
2” Front Stabilizer End Cap
2” Oblique End Cap
∅ 2” Nylon Sleeve
Handle Grip
Round Rubber Bumper
Manual
Foam Grip
Foam Roll
Olympic Sleeve
Quick Release Lock Pin
Hook
∅ 1” Spring Clip
∅ 2” Spring Clip
9-linked Chain
12-linked Chain
20
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of two years on the Frame from the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state. Register on-line at www.impex-fitness.com
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-
999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
22
Download from Www.Somanuals.com. All Manuals Search And Download.
|