NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY HOME GYM
Hardware Identifier
Assembly Instruction
Parts List
MWM-7300
Resistance Chart
Warranty
Ordering Parts
Model
MWM-7300
Retain This
Manual for
Reference
09-15-08
OWNER'S
MANUAL
IMPEX® INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands and feet away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL REPLACEMENT
The warning labels shown here have been placed on the Base Frame and Upper Frame. If the labels are
missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in
the location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required for Assembling the Machine: Two Adjustable Wrenches, two Allen
Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended that
this machine to be assembled by two or more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Attach the front of Main Base Frame (#1) onto the Foot Plate (#7). Secure it with two
M10 x 2 1/8” Allen Bolts (#80) and two Ø ¾” Washers (#91).
C.) Attach the Rear Vertical Frame (#3) to the Main Base Frame (#1). Secure it with one 3
1/8” x 3 ½” Bracket (#27), one M10 x 2 3/8” Allen Bolt (#79) and one Ø ¾” Washer
(#91) to the bottom hole, one M10 x 2 3/8” Carriage Bolt (#73), one Ø ¾” Washer
(#91), and one M10 Aircraft Nut (#94) to the upper hole.
D.) Attach the Front Vertical Frame (#2) onto the Main Base Frame. Attach the Lower
Cross Brace (#16) to the Front Vertical Fame. Align the holes. Secure the Lower Cross
Brace, Front Vertical Frame, and the Main Base Frame together with two M10 x 4 1/8”
Carriage Bolts (#70), two Ø ¾” Washers (#91), and two M10 Aircraft Nuts (#94).
E.) Attach the Upper Frame onto the bracket on the Rear Vertical Frame (#3). Secure it
with one M10 x 5/8” Allen Bolt (#83) and one Ø ¾”Washer (#91).
F.) Attach the Upper Frame onto the Front Vertical Frame (#2). Secure it with two M10 x 2
3/8” Carriage Bolts (#73), one 4 ¾” x 3 1/8” Bracket (#26), two Ø ¾” Washers (#91),
and two M10 Aircraft Nuts (#94).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Slide two Ø 2 ½” x 1” Rubber Bumpers (#65) onto the Guide Rods (#18). Attach
the two Guide Rods onto the Weight Stack Frame (#17). Secure the bottom of
Guide Rods with two M10x 1” Allen Bolts (#82) and two Ø ¾” Washers (#91).
B.) Pull the top of the two Guide Rods off the Weight Stack Frame. Slide 14 Weigh
Plates (#59) onto the Guide Rods. Make sure the deep groove on the Weight
Plates are all facing the machine and downward.
C.) Insert the Selector Rod (#24) through the center hole on the Weight Plates. Slide
the Selector Stem (#37) onto the Guide Rods.
D.) Push the top of Guide Rods back. Secure them to the Weight Stack Frame with
two M8 x 1 5/8” Allen Bolts (#86), four two Ø 5/8” Washers (#92), and two M8
Aircraft Nuts (#95).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Attach the Lower Cross Brace (#16) to the Weight Stack Frame (#17). Secure them with two
M10 x 3 1/8” Carriage Bolts (#72), one 5 1/8” x 1 5/8” Bracket (#58), two Ø ¾” Washers (#91),
and two M10 Aircraft Nuts (#94).
C.) Attach the Upper Cross Brace (#15) to the Rear Vertical Frame (#3) and Upper Frame (#4).
Secure them together with two M10 x 4” Carriage Bolts (#71), two Ø ¾” Washers (#91), and
two M10 Aircraft Nuts (#94).
D.) Secure the other end of Upper Cross Brace to Weight Stack Frame with two M10 x 4”
Carriage Bolts (#71), two Ø ¾” Washers (#91), and two M10 Aircraft Nuts (#94).
E.) Securely tighten all Nuts and Bolts installed in this step and Step-1.
F.) Attach the Leg Press Frame (#8) to the Main Base Frame (#1). Secure it with M10 x 7 5/8”
Allen Bolt (#75), two Ø ¾” Washers (#91), and one M10 Aircraft Nut 9#94). Do not over
tighten the Nut and Bolt. Make sure the Leg Press Frame is adjustable.
G.)Insert a 7 ½” Leg Press Lock Pin (#31) through the holes on Leg Press Frame and the post
on Main Base Frame to hold the Leg Press Frame at desired position.
H.) Attach the Front Press Base (#5) to the Upper Frame. Secure it with one 6 5/8” (#56), two Ø
¾” Washers (#91), and two M10 Aircraft Nuts (#94). Do not over tighten the Nuts. Make
sure the Front Press is able to swivel smoothly.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 3
11
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Right & Left Seat Swivel Frame (#13) & (#14) to Main Base Frame (#1) from each
side. Secure them together with one M12 x 7 7/8” Allen Bolt (#74), two Ø 1” Washer (#90),
and one M12 Aircraft Nut (#93). Do not over tighten the Nut and Bolt. Make sure the
Swivel Frames are able to swivel smoothly.
B.) Repeat above procedure to install the two Front Seat Swivel Frames (#12).
C.) Attach the Seat Support to the top of the two Seat Swivel Frames and Swivel Supports.
Secure them together with two M12 x 7 7/8” Allen Bolts (#74), four Ø 1” Washers (#90), and
one M12 Aircraft Nut (#93).
D.) Attach Leg Developer (#10 to open bracket on the Seat Support. Secure it with one 2 ½”
Axle (#60), two Ø ¾” Washers (#91), and two M10 x 5/8” Allen Bolts (#83).
DIAGRAM 4
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
13
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach the 205” Upper Cable (#35) to the opening at the front of the Upper
Frame (#5). Note: The Ball Stopper on the cable need to be underneath the
Frame.
B.) Attach a Pulley (#51) to the opening. Secure it with one M10 x 4 1/8” Allen Bolt
(#77), two Ø ¾” Washers (#91), and one M10 Aircraft Nut (#94).
C.) Draw the Cable towards the back of the machine to the opening on the Upper
Frame. Repeat B to install a Pulley.
D.) Draw the Cable around the Pulley then pull back towards the open bracket on
the Front Press Base (#5).
E.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#81),
two Ø ¾” Washers (#91), and one M10 Aircraft Nut (#94).
F.) Draw the Cable around the Pulley then to the opening on the Front Vertical
Frame (#2). Repeat Procedure B above to install another Pulley.
G.) Draw the Cable around the Pulley and back to the lower open bracket on Front
Press Base. Repeat Procedure E to install a Pulley.
H.) Draw the Cable around the Pulley and back to the open bracket on the back of
Front Vertical Frame. Repeat Procedure E to install a Pulley.
I.) Draw the Cable around the Pulley then downward. Attach the Cable to in
between the two Double Floating Pulley Brackets (#20). Repeat Procedure E to
install a Pulley. Let the bracket hanging for now.
J.) Draw the Cable around the Pulley then pull the Cable upward to the open
bracket on the Rear Vertical Frame (#3). Repeat Procedure E to install a Pulley.
K.) Draw the Cable around the Pulley Along the Upper Cross Brace to the open
bracket on the Upper Cross Brace (#15). Repeat Procedure E to install a Pulley.
L.) Draw the Cable to the opening on the Weight Stack Frame (#17). Repeat B to
install a Small Pulley (#50) to the opening.
M.) Pull the Cable downward between the two Guide Rods, to the Selector Rod
(#24). Fully thread the bolt at the end of the Cable into the top opening on the
Selector Rod.
N.) Use the Weight Selector Pin (#63) to select the number of Weight Plates to
exercise. Please refer to the Weight Resistance Chart in page-24.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 5
15
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Attach the 118” Lower Cable (#36) to the opening on the bottom of the Leg
Developer (#10).
B.) Attach a Pulley (#51) to the opening. Secure it with one M10 x 3 3/8” Allen Bolt
(#78), two Ø ¾” (#91), and one M10 Aircraft Nut (#94).
C.) Draw the Cable underneath the Pulley to the open bracket on Main Base Frame (#1).
D.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#81), two Ø
¾” (#91), and one M10 Aircraft Nut (#94).
E.) Draw the Cable underneath the Pulley to the opening on the bottom of Front Vertical
Frame (#2). Attach a Pulley to the opening. Secure it with one M10 x 4 1/8” Allen Bolt
(#77), two Ø ¾” (#91), and one M10 Aircraft Nut (#94).
F.) Draw the Cable around the Pulley and then back in between the Right & Left Seat
Swivel Support (#13) & (#14). Install a Pulley to the two Swivel Supports with one
M10 x 7 ½” Allen Bolt (#76), two Ø ¾” Washers (#91), and one M10 Aircraft Nut
(#94).
G.) Draw the Cable around the Pulley and then back to the open bracket on the back of
Front Vertical Frame. Repeat Procedure D to install a Pulley.
H.) Pull up the Cable to the Double Floating Pulley Brackets (#20) installed in Step-5.
I.) Repeat Procedure D to install a Pulley.
J.) Draw the Cable around the Pulley then downward to the bracket on the Rear Vertical
Frame (#3). Secure the end of Cable to the bracket with one M10 x 1” Allen Bolt
(#82), two Ø ¾” Washers (#91), one M10 Aircraft Nut (#94).
K.) Adjust the tension of the Cable by adjusting the Pulley position on the Double
Floating Pulley Bracket (#20). If the cables are too loose, move the Pulley up one
hole. If the cables are too tight, move the Pulley down one hole.
L.) For best performance of the machine, adjust the Cables so the Selector Stem (Top
Plate) on the weight stack is ¼” above the first plate. To select the weight, push
down on the Selector Stem to close the gap then insert the selector pin. This will
remove the slack in the cable system so the range of motion is smooth and tight.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 6
17
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7)
A.) Attach the Front Weight Stack Cover (#29) to the Weight Stack Frame (#17). Secure it
with six M6 x 2 ½” Philips Screws (#89) and six Cover Spacers (#54).
B.) Repeat the Procedure A to install the Rear Weight Stack Cover (#30) to the other side.
DIAGRAM 7
18
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8)
A.) Attach the Backrest Board (#34) to Front Vertical Frame (#2). Secure it with two M8 x 2
1/8” Allen Bolts (#85) and two Ø 5/8” Washers (#92).
B.) Attach the Seat Pad to Seat Support (#11). Secure it with two M8 x 2 1/8” Allen Bolts
(#85) and two Ø 5/8” Washers (#92).
C.) Insert two Foam Tubes (#19) halfway through the holes on Seat Support and Leg
Developer (#10). Push four Foam Rolls (#55) onto the Tubes from both ends. Plug four
Foam Roll End Caps (#44) into the Ends.
D.) Attach the Arm Curl Bracket (#25) to the Arm Curl Pad (#32). Secure it with two M8 x
5/8” Allen Bolts (#87) and two Ø 5/8” Washers (#92).
E.) Attach the Arm Curl Bracket to the open bracket on the Arm Curl Stand (#9). Insert the
M8 x 3 ½” Allen Bolt (#84) through the open track on the Arm Curl Stand and the holes
on the Arm Curl Bracket then secure the Bolt with two Ø 5/8” Washers (#92) and one M8
Aircraft Nut (#95). Do not over tighten the Nut and Bolt. The Bolt needs to be able to
slide on the track freely.
F.) Insert the Arm Curl Stand into the opening on the Leg Developer. Use the M18 Lock
Knob (#52) to lock the Arm Curl Stand in position.
G.)Pull up and flip the Arm Curl Pad along the track facing back to the Leg Press Frame
when doing Leg Press exercises.
H.) Remove the Arm Curl Stand when doing Leg Developer exercises.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 8
20
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9 (See Diagram 9)
A.) Attach the Front Press (#6) to the Front Press Base (#5). Secure it with one 8 ¾” Long
Axle (#57), two Ø ¾” Washers (#91), and two M10 Aircraft Nuts (#94). Do not over
tighten the Nuts. Make sure the Front Press is able to swivel smoothly.
B.) Use the T-shaped Lock Pin (#40) to lock the Front Press to the Front Press Base in
desired position.
C.) Connect the Lat Bat (#21) to Upper Cable with two Hooks (#69) and one Short Chain
(#67).
D.) Connect the Shiver Bar (#22) to Lower Cable with two Hooks and one Long Chain (#68).
DIAGRAM 9
21
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
Main Base Frame
Front Vertical Frame
Rear Vertical Frame
Upper Frame
Front Press Base
Front Press
Foot Plate
Leg Press Frame
Arm Curl Stand
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
2
2
1
1
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
6
1
2
2
3
4
2
4
4
1
10
1
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
Pulley
M18 Lock Knob
Ø 1 ¾” Rubber Bumper
Cover Spacer
Foam Roll
6 5/8” Axle
8 ¾” Long Axle
5 1/8” x 1 5/8” Bracket
Weight Plate
2 ½” Axle
Ø 1” x Ø ½” Bushing
Ø 1” x Ø 5/8” Bushing
Weight Selector Pin
1 5/8” x 2 3/8” Rubber Bumper
Ø 2 ½” x 1” Rubber Bumper
1 1/8” End Cap
Short Chain
Long Chain
Hook
M10 x 4 1/8” Carriage Bolt
M10 x 4” Carriage Bolt
M10 x 3 1/8” Carriage Bolt
M10 x 2 3/8” Carriage Bolt
M12 x 7 7/8” Allen Bolt
M10 x 7 5/8” Allen Bolt
M10 x 7 ½” Allen Bolt
M10 x 4 1/8” Allen Bolt
M10 x 3 3/8” Allen Bolt
M10 x 2 3/8” Allen Bolt
M10 x 2 1/8” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 1” Allen Bolt
M10 x 5/8” Allen Bolt
M8 x 3 ½” Allen Bolt
M8 x 2 1/8” Allen Bolt
M8 x 1 5/8” Allen Bolt
M8 x 5/8” Allen Bolt
M6 x 5/8” Philips Screw
M6 x 2 ½” Philips Screw
Ø 1” Washer
15
1
1
12
4
1
1
2
14
1
24
4
1
1
2
1
1
1
4
2
4
2
3
4
1
1
5
1
1
2
9
3
3
1
4
2
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Leg Developer
Seat Support
Front Seat Swivel Frame
Right Seat Swivel Support
Left Seat Swivel Support
Upper Cross Brace
Lower Cross Brace
Weight Stack Frame
Guide Rod
Foam Tube
Double Floating Pulley Bracket
Lat Bar
Shiver Bar
Rotating Ring
Selector Rod
Arm Curl Bracket
4 ¾” x 3 1/8” Bracket
3 1/8” x 3 ½” Bracket
Ø 1” x 1 1/8” Bushing
Front Weight Stack Cover
Rear Weight Stack Cover
7 ½” Leg Press Lock Pin
Arm Curl Pad
Seat Pad
Backrest Board
205” Upper Cable
118” Lower Cable
Selector Stem
Ø 1” Cone-shaped End Cap
1 5/8” x ¾” End Cap
T-shaped Lock Pin
Ø 2” End Cap
3 1/8” x 1 5/8” End Cap
2 3/8” x 1 5/8” End Cap
Foam Roll End Cap
1 ¾” x Ø 1” Sleeve
Plastic Ring
2
1
12
8
57
12
4
31
3
8
Ø ¾” Washer
Ø 5/8” Washer
M12 Aircraft Nut
M10 Aircraft Nut
M8 Aircraft Nut
Rivet
Ankle Strap
Single Handle
Ø 1 ½” Bushing
3” Sleeve
Handle Grip
Small Pulley
1
1
23
Download from Www.Somanuals.com. All Manuals Search And Download.
MWM-7300 WEIGHT RESISTANCE CHART
WEIGHT PLATE
1
2
3
4
5
6
7
8
9
Station
Lat Pull
10
15
10
15
30
20
26
20
29
60
30
37
30
43
40
48
40
57
50
59
50
71
60
70
60
85
70
81
70
80
90
92 103
80 90
Front Press
Low Pulley
Leg Developer
Leg Press
99 113 127
90 120 150 180 210 240 270
WEIGHT PLATE
10 11
12
13
14
Station
Lat Pull
100 110 120 130 140
114 125 136 147 158
100 110 120 130 140
141 155 169 183 197
300 330 360 390 420
Front Press
Low Pulley
Leg Developer
Leg Press
Note: Each plate weights 10 lbs.
Numbers are approximate.
Actual weights may vary.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX® INC.
LIMITED WARRANTY
®
IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of two years on the Frame from
the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation
under this Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state. Register on-line at www.impex-fitness.com
®
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-
999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
25
Download from Www.Somanuals.com. All Manuals Search And Download.
|