NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
CORNER GYM
EVE-1500
Resistance Chart
Warranty
Ordering Parts
Model
EVE-1500
Retain This
Manual for
Reference
08-17-05
OWNER'S
MANUAL
Made under license from trademark owner Everlast
Worldwide Inc., New York.
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF
THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL REPLACEMENT
The warning labels shown here have been placed on the Left Base Frame and Right Upper Frame. If the
labels are missing or illegible, please call customer service at 1-800-999-8899 for replacements. Apply the
labels in location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine to avoid
possible injury.
STEP 1 (See Diagram 1)
A.) Place the Right and Left Base Frames (#1 & #14) on a flat surface. Make sure there is enough
space to assemble the machine.
B.) Do not tighten the nuts and bolts until instructed to do so.
C.) Attach the Left Base Frame (#14) and the Right Base Frame (#1) to the bottom of Rear
Vertical Beam (#9). Align the holes and secure the upper hole with one M10 x 2 ½” Carriage
Bolt (#87), Ø ¾” Washer (#94), and M10 Aircraft Nut (#97). Secure the lower hole with one
M10 x 2 3/8” Allen Bolt (#84) and ∅ ¾” Washer (#94).
DIAGRAM 1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Insert two Guide Rods (#12) into the holes on the Guide Rod Base (#10). Secure each
Guide Rod with one M10 x ¾” Allen Bolt (#80) and Ø ¾” Washer (#94) from the bottom.
B.) Attach the Guide Rod Base to the Left and Right Base Frames (#1 & #14). Secure each
side with one M10 x 2 1/8” Allen Bolt (#83) and Ø ¾” Washer (#94).
DIAGRAM 2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Right Vertical Beam (#3) onto the Right Base Frame (#1). Secure it with
two M10 x 2 ½” Carriage Bolts (#87), Ø ¾” Washers (#94), and M10 Aircraft Nuts
(#97).
B.) Attach the Left Vertical Beam (#17) onto the Left Base Frame (#14). Secure it with
two M10 x 2 ½” Carriage Bolts (#87), Ø ¾” Washers (#94), and M10 Aircraft Nuts
(#97).
C.) Place the Right Upper Frame (#4) onto the Right Vertical Beam (#3). Secure it with
two M10 x 2 ½” Carriage Bolts (#87), one 4 3/8” x 1 ¾” Bracket (#32), two Ø ¾”
Washers (#94), and two M10 Aircraft Nuts (#97).
D.) Place the Left Upper Frame (#18) onto the Left Vertical Beam (#17). Secure it with
two M10 x 2 ½” Carriage Bolts (#87), one 4 3/8” x 1 ¾” Bracket (#32), two Ø ¾”
Washers (#94), and two M10 Aircraft Nuts (#97).
E.) Attach the rear of Right Upper Frame (#4) to the Rear Vertical Beam (#9). Attach the
rear of Left Upper Frame (#18) to the Rear Vertical Beam from the other side. Align
the holes and secure them together with one M10 x 2 ½” Carriage Bolt (#87), Ø ¾”
Washer (#94), and M10 Aircraft Nut (#97) to the lower hole. Secure the upper hole
with one M10 x 2 3/8” Allen Bolt (#84) and Ø ¾” Washer (#94).
F.) Move the machine to its final location before move on to the next step.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 3
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Slide nineteen Weight Plates (#59) onto the Guide Rods (#12). Make sure the grove
on the Plates all face toward front of the machine. Insert the Selector Rod (#13) into
the center hole. It is strongly recommended to spray lubricant such as WD-40 on the
two Guide Rods to minimize friction.
B.) Slide the Selector Stem (#58) onto the two Guide Rods and the Selector Rod. Slide
the Ø 1 ¾” x 2” Rubber Bumper (#72) onto the Selector Rod. Insert a Weight
Selector Pin (#50) into the selected hole on the Plates.
C.) Place the Guide Rod Upper Frame (#11) onto the Guide Rods. Secure it with two
M10 x ¾” Allen Bolts (#80) and Ø ¾” Washers (#94).
D.) Attach each end of the Guide Rod Upper Frame to the Right and Left Upper Frames
(#4 & #18). Secure each end with one M10 x 2 1/8” Allen Bolt (#83) and Ø ¾”
Washer (#94).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 4
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Right Seat Support (#2) onto the Right Base Frame (#1). Secure it with
one M10 x 2 ½” Carriage Bolt (#87), Ø ¾” Washer (#94), and M10 Aircraft Nut
(#97).
B.) Attach the Right Seat Support (#2) to the Right Vertical Beam (#3). Secure it with
two M10 x 2 ½” Carriage Bolts (#87), one 4 3/8” x 1 ¾” Bracket (#32), two Ø ¾”
Washers (#94), and two M10 Aircraft Nuts (#97).
C.) Attach the Leg Developer (#7) to the bracket on the Right Seat Support (#2).
Secure it with a 2” Axle (#51), two M10 x ¾” Allen Bolts (#80), and two Ø ¾”
Washers (#94).
DIAGRAM 5
13
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6)
A.) Attach the Left Seat Support (#15) to the Left Base Frame (#14). Secure it with one M10 x
2 ½”Carriage Bolts (#87), Ø ¾” Washer (#94), and M10 Aircraft Nut (#97).
B.) Attach the Left Seat Support to the Left Vertical Beam (#17). Secure it with two M10 x 2 ½”
Carriage Bolts (#87), one 4 3/8” x 1 ¾” Bracket (#32), two Ø ¾” Washers (#94), and two
M10 Aircraft Nuts (#97).
C.) Attach the Leg Press Frame (#16) to the bracket on the Left Base Frame (#14). Secure it
with one M12 x 3” Allen Bolt (#79), two Ø 1” Washers (#95), and one M12 Aircraft Nut
(#98).
D.) Attach two Leg Press Diagonal Supports (#31) to the Leg Press Frame from both sides.
Secure them with two M10 x 2 ½” Carriage Bolts (#87), Ø ¾” Washers (#94), and M10
Aircraft Nuts (#97). Make sure the Leg Press Frame is able to swivel on its pivot.
E.) Securely tighten all Nuts and Bolts previously installed.
DIAGRAM 6
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7)
A.) Align the Front Press Base (#19) to the Left Upper Frame (#18). Insert a 6” Axle (#52) through
the holes and secure it with two Ø ¾” Washers (#94) and M10 Aircraft Nuts (#97).
B.) Insert the axle on the Left Butterfly (#20) through the holes on the Front Press Base. Slide a Ø 1
½” x Ø ¾” Washer (#66) onto the axle. Secure the axle with one Lock Ring (#65), M6 x 1 ¼”
Allen Screw (#90), and M6 Aircraft Nut (#96).
C.) Push a Large Foam Roll (#47) onto the Left Butterfly. Insert Left Press Handle (#22) into the
Left Butterfly. Secure it with one M10 x ¾” Allen Bolt (#80) and Ø ¾” Washer (#94).
D.) Repeat Procedures B & C above to install the Right Butterfly (#21).
E.) Attach the Butterfly Pulley Bracket (#24) to the back of the Left Vertical Beam (#17). Secure it
with one M10 x 2 ½” Carriage Bolt (#87), Ø ¾” Washer (#94), and M10 Aircraft Nut (#97).
F.) Attach two Swivel Pulley Brackets (#26) to the Butterfly Pulley Bracket (#24). Secure each
Swivel Bracket with one M10 x 2 ½” Allen Bolt (#85), two Ø ¾” Washers (#94), and one M10
Aircraft Nut (#97). Do not overt tighten the Brackets. Make sure they are able to swivel.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Loop Diagram
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8 & Cable Loop Diagram)
A.) Attach one end of the 118” Butterfly Cable (#42) to the hook on the Right Butterfly (#21).
Draw the Cable to the right open Swivel Pulley Bracket (#26).
B.) Attach a Pulley (#60) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#82), two ∅
¾” Washers (#94), and one M10 Aircraft Nut (#97).
C.) Draw the Cable around the Pulley then downward. Repeat Step B above to install a Pulley to
the Angled Double Floating Pulley Bracket (#27). Let the Bracket hanging for now. Draw the
Cable upward to the left open Swivel Pulley Bracket.
D.) Repeat Step B above to install another Pulley to the left Swivel Pulley Bracket. Draw the
Cable around the Pulley to the Left Butterfly (#20). Attach the end of the Cable to the hook
on the Left Butterfly.
DIAGRAM 8
17
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9 (See Diagram 9 & Cable Loop Diagram)
A.) Attach the end of the 115” Front Press Cable (#43) to the open bracket on the Left
Vertical Beam (#17). Secure it with one M10 x 1” Allen Bolt (#81), two Ø ¾” Washers
(#94), and one M10 Aircraft Nut (#97).
B.) Draw the Cable to the opening on the Front Press Base (#19). Attach a Pulley to the
opening. Secure the Pulley to the Front Press Base with one M10 x 5 1/8” Allen Bolt
(#86), two Ø ¾” Washers (#94), and one M10 Aircraft Nut (#97).
C.) Draw the Cable around the Pulley then back to the opening on the Left Vertical Beam
to the open bracket underneath the Left Upper Frame (#18). Attach a Pulley to the
bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#82), two Ø ¾” Washers (#94), and
one M10 Aircraft Nut (#97).
D.) Draw the Cable around the Pulley then downward. Install a Pulley to two Flat Double
Floating Pulley Brackets (#36). Draw the Cable around the Pulley then upward to the
open bracket on the Left Upper Frame. Let the Bracket hanging for now.
E.) Install a Small Pulley (#61) to the bracket with a 2 ½” L-shaped Cable Retainer (#34).
F.) Draw the Cable over the Small Pulley then to the open bracket on the Guide Rod
Upper Frame (#11). Install a Small Pulley to the bracket with a 2 ½” L-shaped Cable
Retainer (#34).
G.) Draw the Cable around the Small Pulley then downward to the Selector Rod (#13).
Thread the Bolt at the end of the Cable into the Selector Rod. Use the Nut on the Bolt
to secure the Bolt into the Rod.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 9
19
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 10 (See Diagram 10 & Cable Loop Diagram)
A.) Attach the 180” Upper Cable (#40) to the front opening on the Right Upper Frame (#4).
B.) Place a Pulley (#60) to the opening and secure it with one M10 x 2 3/8” Allen Bolt (#84),
two Pulley Bushings (#78), and one M10 Aircraft Nut (#97). Make sure the ball stopper
on the Cable is underneath the Right Upper Frame.
C.) Draw the Cable over the Pulley along the Right Upper Frame to the rear opening on the
Right Upper Frame. Repeat Procedure B above to Install a Pulley. Draw the Cable
around the Pulley then downward. Install a Pulley to two Flat Double Floating Pulley
Brackets (#36). Draw the Cable around the Pulley then upward to the open bracket
underneath the Right Upper Frame. Let the Brackets hanging for now.
D.) Install a Pulley to the bracket. Draw the Cable around the Pulley then downward. Install
a Pulley to two Flat Double Floating Pulley Brackets. Draw Cable around the Pulley
then to the opening on the Right Vertical Beam (#3). Let the Brackets hanging for now.
E.) Repeat Procedure B above to install a Pulley to the opening. Draw the Cable around
the Pulley then through the opening. Insert the end of Cable through a Ball Stopper
(#46) to a Cable Head Connector (#45). Drop the end into the slot on the connector.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 11 (See Diagram 11 & Cable Loop Diagram)
A.) Attach the 105” Lower Cable (#41) to the opening on the bottom of Leg Developer (#7).
B.) Attach a Pulley (#60) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#84), two
Pulley Bushings (#78), and one M10 Aircraft Nut (#97).
C.) Draw the Cable underneath the Pulley towards the back of the machine to the open bracket
on the Right Base Frame (#1). Attach a Pulley to the Bracket. Secure it with one M10 x 1 ¾”
Allen Bolt (#82), two ∅ ¾” Washers (#94), and one M10 Aircraft Nut (#97).
D.) Draw the Cable underneath the Pulley through the opening on the bottom of Right Vertical
Beam (#3) to the open bracket on the Right Base Frame. Install a Pulley to the bracket with
a 2 7/8” L-shaped Cable Retainer (#33).
E.) Draw the Cable around the Pulley then upward to the Flat Double Floating Pulley Brackets
(#36) previously installed in Step-10. Install another Pulley.
F.) Draw the Cable around the Pulley then downward. Connect the Cable to the first open
bracket on the Right Base Frame with a C-clip (#75) and a Short Chain (#74).
G.)Secure the Short Chain to the bracket with one M10 x 1” Allen Bolt (#81), two Ø ¾” Washers
(#94), and one M10 Aircraft Nut (#97). After completing the entire cable installations, come
back to this Short Chain and adjust the Cable tension by adjusting the length of the Chain.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 12 (See Diagram 12 & Cable Loop Diagram)
A.) Attach one end of the 276” Leg Press Cable (#44) to the open bracket underneath
the Left Seat Support (#15). Secure it with one M10 x 1” Allen Bolt (#81), two Ø ¾”
Washers (#94), and one M10 Aircraft Nut (#97).
B.) Attach a Pulley to the top opening on the Leg Press Frame (#16). Secure it with
one M10 x 2 3/8” Allen Bolt (#84), two Pulley Bushings (#78), and one M10 Aircraft
Nut (#97).
C.) Draw the Cable around the Pulley then back to the top opening on the Left Seat
Support. Repeat Procedure B above to install a Pulley.
D.) Draw the Cable around the Pulley back to the lower opening on the Leg Press
Frame (#16). Repeat Procedure B above to install a Pulley.
E.) Draw the Cable around the Pulley along the Left Base Frame (#14) through the
opening on the bottom of Left Vertical Beam (#17) to the first open bracket on the
Left Base Frame.
F.) Install a Pulley and secure it with one M10 x 1 ¾” Allen Bolt (#82), one 2 7/8” L-
shaped Cable Retainer (#33), two Ø ¾” Washers (#94), and one M10 Aircraft Nut
(#97).
G.) Draw the Cable underneath the Pulley then upward to the Angled Double Floating
Pulley Bracket (#27) previously installed in Step-8. Install a Pulley to the Bracket.
H.) Draw the Cable around the Pulley then downward to the second open bracket on
the Left Base Frame. Install a Pulley with an U-shaped Cable Retainer (#35).
I.) Draw the Cable upward to the Flat Double Floating Pulley Brackets (#36) previously
installed in Step-9. Install another Pulley.
J.) Draw the Cable around the Pulley then downward to the open bracket on the rear
of Left Base Frame. Install a Pulley with a 2 7/8” L-shaped Cable Retainer (#33).
K.) Draw the Cable underneath the Pulley across the corner to the open bracket on the
Right Base Frame (#1). Repeat Procedure J above to install a Pulley.
L.) Draw the Cable underneath the Pulley then upward to the Flat Double Floating
Pulley Bracket (#36) previously installed in Step-10. Install another Pulley.
M.) Draw the Cable around the Pulley then downward to the open bracket on the Right
Base Frame (#1). Secure the end of the Cable with one M10 x 1” Allen Bolt (#81),
two Ø ¾” Washers (#94), and one M10 Aircraft Nut (#97).
N.) Check the tension of the cable loop system. If the cables are too loose, shorten the
Short Chain previously installed in Step 11 G.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 12
23
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 13 (See Diagram 13)
A.) Attach a Backrest Board (#38) to the Right Vertical Beam (#3). Secure it with two M8
x 2 1/8” Allen Bolts (#89) and Ø 5/8” Washers (#93).
B.) Attach a Seat Pad (#37) onto the Right Seat Support (#2). Secure it with two M8 x 2
1/8” Allen Bolts (#89) and Ø 5/8” Washers (#93).
C.) Attach the Arm Curl Pad (#39) to the Arm Curl Stand (#6). Secure it with two M8 x
5/8” Allen Bolts (#88) and Ø 5/8” Washers (#93).
D.) Insert the Arm Curl Stand into the opening on the Right Seat Support and secure it
with a Lock Knob (#53).
DIAGRAM 13
24
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 14 (See Diagram 14)
A.) Attach a Backrest Board (#38) to the Left Vertical Beam (#17). Secure it with two M8
x 2 1/8” Allen Bolts (#89) and Ø 5/8” Washers (#93).
B.) Attach a Seat Pad (#37) onto the Left Seat Support (#15). Secure it with two M8 x 2
1/8” Allen Bolts (#89) and Ø 5/8” Washers (#93).
C.) Attach the Leg Press Plate (#25) to the Leg Press Frame (#16). Secure it with a Leg
Press Lock Pin (#49).
DIAGRAM 14
25
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 15 (See Diagram 15)
A.) Attach the Weight Stack Cover (#29) to the Guide Rod Upper Frame (#11) and Guide Rod
Base (#10). Secure it with four M10 x ¾” Allen Bolts (#80) and Ø ¾” Washers (#94).
DIAGRAM 15
26
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 16 (See Diagram 16)
A.) Connect the Lat Bar (#5) to the 180” Upper Cable (#40) with two C-clips (#75) and a Short
Chain (#74). Store the Lat Bar onto the hooks on the Right Upper Frame.
B.) Connect the Abdominal Strap (#99) to the Cable Head Connector (#45) with a C-clip. Secure
the C-clip to the Connector with one M10 x 1 1/8” Allen Bolt (#92) and M10 Aircraft Nut (#97).
C.) Insert two Foam Tubes (#30) halfway through the holes on the Right Seat Support (#2) and
Leg Developer (#7). Push four Foam Rolls (#48) onto the Tubes form both sides. Plug four
Foam Roll End Caps (#62) into the ends.
D.) Connect the Arm Curl Handle (#8) to the 105” Lower Cable (#41) with a Long Chain (#73) and
two C-clips.
DIAGRAM 16
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
Right Base Frame
Right Seat Support
Right Vertical Beam
Right Upper Frame
Lat Bar
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
2” Axle
6” Axle
Lock Knob
5 ¼” Grip
Ø 1 ½” x 1” Bushing
1 ¾” Square End Cap
Ø 1” Con-shaped End Cap
Selector Stem
Weight Plate
Pulley
Small Pulley
Foam Roll End Cap
Sleeve
1 5/8” x ¾” End Cap
Lock Ring
Ø 1 ½” x Ø ¾” Washer
1 ½” End Cap
Ø 1” x Ø ¾” Bushing
Ø 1 ½” x 5/8” Rubber Bumper
Ø 2” x 1” Rubber Bumper
Ø 1 ¾” x 1 5/8” Rubber Bumper
Ø 1 ¾” x 2” Rubber Bumper
Long Chain
1
1
1
8
2
12
1
Arm Curl Stand
Leg Developer
Arm Curl Handle
Rear Vertical Beam
Guide Rod Base
Guide Rod Upper Frame
Guide Rod
1
9
19
26
2
4
1
2
2
2
2
2
1
2
2
1
1
2
6
8
2
14
1
12
4
20
4
9
2
1
19
2
8
2
3
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Selector Rod
Left Base Frame
Left Seat Support
Leg Press Frame
Left Vertical Beam
Left Upper Frame
Front Press Base
Left Butterfly
Right Butterfly
Left Press Handle
Right Press Handle
Butterfly Pulley Bracket
Leg Press Plate
Swivel Pulley Bracket
Short Chain
C-clip
Ø 1” x Ø 5/8” Bushing
Ø 1” x ½” Bushing
Pulley Bushing
Angled Double Floating Pulley Bracket 1
Arm Curl Handle Bar
Weight Stack Cover
Foam Tube
Leg Press Diagonal Support
4 3/8” x 1 ¾” Bracket
2 7/8” L-shaped Cable Retainer
2 ½” L-shaped Cable Retainer
U-shaped Cable Retainer
Flat Double Floating Pulley Bracket
Seat Pad
Backrest Board
Arm Curl Pad
180” Upper Cable
105” Lower Cable
118” Butterfly Cable
115” Front Press Cable
276” Leg Press Cable
Cable Head Connector
Ball Stopper
1
1
2
2
4
4
2
1
6
2
2
1
1
1
1
1
1
1
1
2
4
1
1
M12 x 3” Allen Bolt
M10 x ¾” Allen Bolt
M10 x 1” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 2 1/8” Allen Bolt
M10 x 2 3/8” Allen Bolt
M10 x 2 ½” Allen Bolt
M10 x 5 1/8” Allen Bolt
M10 x 2 ½” Carriage Bolt
M8 x 5/8” Allen Bolt
M8 x 2 1/8” Allen Bolt
M6 x 1 ¼” Allen Screw
M6 x 5/8” Philips Screw
M10 x 1 1/8” Allen Bolt
Ø 5/8” Washer
Ø ¾” Washer
Ø 1” Washer
M6 Aircraft Nut
M10 Aircraft Nut
M12 Aircraft Nut
Abdominal Strap
Ankle Strap
1
10
95
2
2
56
1
1
1
1
Large Foam Roll
Foam Roll
Leg Press Lock Pin
Weight Selector Pin
Single Handle
28
Download from Www.Somanuals.com. All Manuals Search And Download.
EVE-1500 Weight Resistance Chart
WEIGHT FRONT
LOW
LAT
BAR
30
BUTTERFLY
AB
LEG
PLATE
1
PRESS PULLEY
STATION
15
STATION PRESS
25
35
30
40
30
40
30
45
2
40
20
3
45
50
50
25
50
60
4
55
60
60
30
60
75
5
65
70
70
35
70
90
6
7
8
9
75
85
95
80
90
80
90
40
45
50
55
60
65
70
75
80
85
90
95
100
105
80
90
105
120
135
150
165
180
195
210
225
240
255
270
285
300
100
110
120
130
140
150
160
170
180
190
200
210
100
110
120
130
140
150
160
170
180
190
200
210
100
110
120
130
140
150
160
170
180
190
200
210
105
115
125
135
145
155
165
175
185
195
205
10
11
12
13
14
15
16
17
18
19
*Each plate weights approximately 10 lbs.
*Resistance measured in pounds.
*Numbers are approximate. Actual number may vary.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of two years on the Frame from the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state. Register on-line at www.impex-fitness.com
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-
999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
30
Download from Www.Somanuals.com. All Manuals Search And Download.
|