322C
322L
325L
325L
325L
325C
325C
XT-SERIES
X-SERIES
X-SERIES
Operator's manual (EPA)
Read through the Operator‘s Manual carefully and
understand the content before using the machine.
101 91 71-95
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOL EXPLANATION
Symbols
• Always wear approved protective
gloves.
WARNING! Clearing saws,
brushcutters and trimmers can be
dangerous!
Careless or incorrect use can result in
serious or fatal injury to the operator
or others.
• Use anti-slip and stable boots.
Read through the Operator‘s Manual
carefully and understand the content
before using the machine.
• Only use non-metallic, flexible
cutting elements, that is trimmer
head with trimmer cord.
Always use
• A protective helmet where there is
a risk of falling objects
• Ear protection
• Only intended for the trimmer
head.
• Approved eye protection
• Max. speed of output axle, rpm
max
10000 rpm
Other symbols/decals on the machine refer to
special certification requirements for certain
markets.
• This product is in accordance with
applicable CE directives.
Checks and/or maintenance should
be carried out with the engine
switched off, with the stop switch in
the STOP position.
• Beware of thrown objects and
ricochets.
Always wear approved protective
gloves.
• The operator of the machine shall
ensure, while working, that no
persons or animals come closer
than 15 metres.
15 m
15 m
50FT
50FT
Regular cleaning required.
• Blade can thrust violently when
coming in contact with any object.
Blade thrust can cause amputation
of arms or legs. Keep people and
animals 50 feet away. Never use
blades unless recommended
handlebar, shoulder strap,
Ocular control.
attaching hardware and blade
deflector are installed.
• Arrows which show limits for
handle mounting.
Approved eye protection must always
be used.
2 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Husqvarna AB has a policy of continuous product development
and therefore reserves the right to modify the design and
appearance of products without prior notice.
List of contents
Maintenance, replacement, or repair of the emission control
devices and systems may be performed by any nonroad
engine repair establishment or individual.
SYMBOL EXPLANATION
Symbols ............................................................................... 2
CONTENTS
List of contents .................................................................... 3
SAFETY INSTRUCTIONS
WARNING!
Under no circumstances may the design
of the machine be modified without the
permission of the manufacturer. Always
use genuine accessories. Non-authorized
modifications and/or accessories can
result in serious personal injury or the
death of the operator or others.
Personal protective equipment ............................................. 4
The machine‘s safety equipment .......................................... 4
Control, maintenance and service of the machine‘s safety
equipment ...................................................................... 6
Cutting equipment .............................................................. 7
General safety instructions ................................................... 8
General working instructions ............................................... 9
Basic working techniques ..................................................... 9
WHAT IS WHAT?
!
Your warranty does not cover damage or
liability caused by the use of non-
authorized accessories or replacement
parts.
What is what on the trimmer?............................................ 11
ASSEMBLY
Assembling the loop handlebar (322C, 325CX)................. 12
Assembling the loop handlebar (322L, 325L-X/L-XT) ...... 12
Assembling and dismantling the two-part shaft (325L-XT) 12
Assembly of the trimmer head ........................................... 12
Assembling the spray guard and trimmer head
Superauto II (322L, 325L-X/L-XT) ............................. 13
Assembling other guards and cutting equipment
HUSQVARNA AB HUSKVARNA SWEDEN
(322L, 325L-X/L-XT).................................................. 13
Fitting the spray guard and trimmer head (322C) .............. 13
Fitting the spray guard and trimmer head (325CX) ........... 14
FUEL HANDLING
Fuel mixture ...................................................................... 15
Fuelling.............................................................................. 15
START AND STOP
Control before starting....................................................... 16
Start and stop..................................................................... 16
MAINTENANCE
IMPORTANT ENGINE INFORMATION
TWC
THIS ENGINE CONFORMS TO U.S. EPA PH1
FOR SMALL NON - ROAD ENGINES.
REFER TO OPERATOR`S MANUAL FOR
MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
This decal certifies that the product has been approved in
accordance with American exhaust emissions requirements
EPA PH1.
Carburetor ......................................................................... 17
Muffler .............................................................................. 19
Cooling system .................................................................. 19
Spark plug.......................................................................... 19
Two-part shaft.................................................................... 19
Air filter ............................................................................. 20
Angle gear .......................................................................... 20
Maintenance schedule ........................................................ 20
TECHNICAL DATA
322C ................................................................................. 21
322L .................................................................................. 21
325L-X/L-XT .................................................................... 21
325CX ............................................................................... 22
EMISSION CONTROL WARRANTY STATEMENT
Your warranty rights and obligations .................................. 23
English – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Personal protective equipment
The machine‘s safety equipment
MPORTANT INFORMATION
This section describes the machine‘s safety equipment, its
function and how checks and maintenance are carried out to
ensure that it operates correctly. (See the chapter “What is
what“ to locate where this equipment is positioned on your
machine.)
•
A clearing saw, brushcutter or trimmer used
incorrectly or carelessly can become a
dangerous tool, that can cause serious or fatal
injury to the operator or others. It is extremely
important that you read and understand the
content of this manual.
WARNING!
Never use a machine with defective safety
equipment. Follow the control,
maintenance and service instructions
described in this section.
!
•
When using a trimmer, personal protective
equipment approved by the appropriate
authorities must be used. Personal protective
equipment does not eliminate the risk of
accidents, however, it can reduce the effects of
an injury in the event of an accident. Ask your
dealer for help when choosing protective
equipment.
1. Throttle trigger
lock
A
The throttle trigger lock is
designed to prevent the
throttle from accidentally
being engaged. When the
trigger lock (A) is pressed
into the handle (= when you
hold the handle) the throttle
(B) is released. When the
grip on the handle is
released the throttle and the
throttle trigger lock return
to their original positions.
This takes place via two
independent return spring
systems. This means that the
throttle is automatically
locked in its “idling“
WARNING!
Remove your hearing protection as soon as
you stop the engine, so that you can hear
any noises or warning signals.
!
GLOVES
B
Gloves should be worn
when necessary, e.g., when
assembling cutting
equipment.
A
EAR PROTECTION
Ear protection offering
sufficient dampening effect
should be used.
B
EYE PROTECTION
Blows from branches or
objects thrown by the
rotating cutting equipment
can damage the eyes.
position.
2. Stop switch
The stop switch should be
used to stop the engine.
BOOTS
Use anti-slip and stable
boots.
"
3. Cutting
attachment guard
CLOTHING
Wear clothes made of a
strong fabric and avoid
loose clothing that can
catch on shrubs and
branches. Always wear
heavy, long pants. Do not
wear jewelry, short pants,
sandals or go barefoot.
Secure hair so it is above
shoulder level.
This guard is intended to
prevent objects from being
thrown towards the
operator and to protect the
operator from
unintentionel contact with
the cutting attachment.
WARNING!
Under no circumstances may the cutting
equipment be used without an approved
guard fitted. See the chapter “Technical
data”. If the wrong guard or a defective
guard is fitted this can cause serious
personal injury.
FIRST AID KIT
!
A first aid kit should be
carried by operators of
clearing saws, brushcutters
or trimmers.
4 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
5. Muffler
4. Vibration
damping system
The muffler is designed to
give the lowest possible noise
level and to direct the engine‘s
exhaust fumes away from the
operator. Muffler fitted with
catalytic converter is also
Your machine is equipped
with a vibration damping
system, which is designed
to give as vibration-free
and comfortable use as
possible.
designed to reduce harmful
exhaust components.
In countries that have a warm
and dry climate the risk of fire
is obvious. We have therefore
fitted certain mufflers with a
spark arrest screen. Make sure
that your muffler is fitted
with this kind of screen.
It is extremely important that
the instructions for checking,
maintaining and servicing the
muffler are followed. (see the
section “Control, maintenance
and service of the machine‘s
safety equipment“).
Use of incorrectly wound
cord or incorrect cutting
equipment increases the
level of vibration.
The machine’s vibration
damping system reduces
the transfer of vibrations
between the engine unit/
cutting equipment and the
machine’s handle unit.
WARNING!
Mufflers fitted with catalytic converters
!
!
become extremely hot during use and
after stopping. This also applies at idling
speeds. Contact can result in burns to
the skin. Be observant to the risk of fire!
WARNING!
Bear in mind that exhaust fumes:
• contain carbon monoxide, which can
cause carbon monoxide poisoning.
Therefore never start or run the machine
indoors.
• are hot and can contain sparks that can
cause fires. Never start the machine
indoors or close to inflammable material.
WARNING!
Over exposure to vibrations can result in
!
blood-vessel or nerve injury to persons
suffering with blood circulation problems.
Seek medical attention if you experience
physical symptoms that can be related to
over exposure to vibrations. Examples of
such symptoms are “numbness“, lack of
feeling, “tickling“, “pricking“, “pain“ lack of
or a reduction in normal strength, changes
in the colour of the skin or its surfaces.
These symptoms normally appear in the
fingers, hands or wrists.
6. Cutting
equipment
The trimmer head is
intended for trimming
grass.
7. Locking nut
A locking nut is used to
secure some types of cutting
equipment on the output
shaft.
English – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
3. Cutting
attachment guard
Control, maintenance and service of
the machine‘s safety equipment
IMPORTANT INFORMATION
• Ensure that the spray
guard is undamaged and
is not cracked.
•
•
All service and repairs to the machine require
special training.
• Replace the guard if it
has been exposed to
impact or is cracked.
This applies especially to the machine‘s safety
equipment. If the machine does not meet any
of the controls listed below you should
contact your service workshop.
• Always use the prescribed
blade an guard
combination, see chapter
"Technical data".
•
The purchase of one of our products
guarantees that professional repair and
servicing will be carried out on it. If the point
of purchase is not one of our servicing deal
ers, please ask for details of the closest
service workshop.
4. Vibration
damping system
1. Throttle trigger
lock
• Check the vibration
damping element
regularly for material
cracks and distortion.
• Check that the throttle is
locked in the “idling
position“ when the
throttle trigger lock is in
its original position.
• Check that the vibration
damping element is
undamaged and securely
attached.
• Press in the throttle
trigger lock and make sure
it returns to its original
position when released.
• Ensure that the throttle
and throttle trigger lock
move easily and that their
return spring systems
function.
• See section "Start". Start
the machine and apply
full throttle. Release the
throttle and check that the
cutting equipment stops
and remains at a standstill.
If the cutting equipment
rotates with the throttle in
the idling position then
the carburettor‘s idling
setting must be checked.
See chapter
5. Muffler
1.Never use a machine that
has a defective muffler.
2.Check regularly that the
muffler is secure.
#
3.If your muffler is fitted
with a spark arrest screen
then it should be cleaned
regularly. A blocked
screen leads to the engine
overheating with serious
damage as a result. Never
use a muffler with a
defective spark arrest
screen.
“Maintenance“.
2. Stop switch
• Start the engine and make
sure that the engine stops
when the stop switch is
moved to the stop
position.
6 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
6. Cutting equipment
Cutting equipment
The section describes how through correct maintenance and
through using the right type of cutting equipment you can:
• Obtain maximum clearing capacity.
IMPORTANT INFORMATION
The section describes how through correct
maintenance and through using the right type of
cutting equipment you can obtain maximum
clearing capacity and increase the service life of
the cutting equipment.
• Increase the service life of the cutting equipment.
Two basic rules:
•
Only use the cutting and guard equipment we
recommend! See chapter “Technical data“.
1)Only use the cutting
and guard equipment
we recommend! See
chapter “Technical
data“.
Trimmer head
• Only use a trimmer head
and trimmer cord that is
recommended. These
have been tested by the
manufacturer to suit a
particular engine size.
This is especially
important when a fully
automatic trimmer head
is used. Only use the
cutting equipment we
recommend! See chapter
“Technical data“.
2)Check the cutting
equipment with regard
to damage and crack
formation. Damaged
cutting equipment
should always be
replaced.
7. Locking nut
• Protect your hand from
injury when assembling,
use the blade guard as
protection when tightening
with a socket spanner.
Tighten the nut by turning
against the direction of
rotation. Loosen the nut by
turning in the direction of
rotation. (NOTE! the nut
has a left-hand thread).
• Generally smaller machines require a small trimmer head
and vice versa. This is because when clearing using a cord
the engine must throw out the cord radially from the
trimmer head and also meet resistance from the grass being
cleared.
• The length of the cord is also important. A longer cord
requires greater engine power than a shorter cord of the
same diameter.
• Make sure the knife positioned on the trimmer guard is
intact. This is used to cut the cord to the correct length.
• Tighten the nut using a
socket spanner, 35 - 50
Nm (3.5 - 5 kpm).
• To increase the life of the cord it can be soaked in water for
a few days. This will make the line tougher and it will keep
longer.
NOTE!
The locking nut‘s nylon lock must not be so worn that it can
be turned by hand. The lock shall hold at least 1.5 Nm. The
nut should be replaced after it has been put on approx. 10
times.
IMPORTANT INFORMATION
Always ensure the trimmer cord is wound tightly
and evenly around the drum, otherwise harmful
vibrations will occur.
WARNING!
Never use a machine with defective
safety equipment.The safety equipment
should be maintained as described in this
section. If your machine does not meet
any of these controls you should contact
your service workshop.
!
WARNING!
Always stop the engine before starting
work on any part of the cutting equipment.
!
This continues to rotate even after the
throttle has been released. Ensure that the
cutting equipment has stopped completely
and remove the cable from the spark plug
before you start to work on it.
English – 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Fuel safety
General safety instructions
IMPORTANT INFORMATION
• Always use a fuel container
with an anti-spill valve.
• The machine is only designed for trimming grass.
• The only accessories to be used with the engine
unit as a drive source are the cutting units we
recommend in the chapter “Technical data“.
• Never fill the machine
while the engine is
running. Always stop the
engine and let it cool for a
few minutes before
refuelling.
• Never use the machine if you are tired, if you
have consumed alcohol, or if you are taking
medicines that can affect your sight, your
judgement or the control of your body.
• Use personal protective equipment. See the
section “Personal protective equipment“.
• Provide good ventilation
when filling or mixing fuel
(petrol and 2-stroke oil).
• Never use a machine that has been modified so
that it no longer corresponds with the original
design.
Min. 3 m
(10 ft)
• Never use a machine that is faulty. Follow the
maintenance, control and service instructions in
this Operator‘s Manual. Some maintenance and
service actions should be carried out by trained
and qualified specialists. See the chapter
“Maintenance“.
• Move the machine at least
3 m from the filling
position before starting.
• Never start the machine:
• All covers and guards must be fitted before
starting the machine. Check that the spark plug
cap and HT lead are not damaged, otherwise you
could get an electric shock.
a)If you have spilt fuel on it.
Wipe up all spillage.
b)If you have spilt fuel on
yourself or your clothes.
Change your clothes.
• The machine operator shall ensure, while
working, that no persons or animals come closer
than 15 metres (50 feet). When several operators
are working in the same area the safety distance
should be at least double tree length, however, at
least 15 metres (50 feet).
c)If there is a fuel leak.
Make regular checks for
leakage from the fuel cap
and the fuel supply pipes.
WARNING!
Faulty cutting equipment increases the risk
of accidents.
!
Start
Transport and storage
WARNING!
When the engine is started with the choke
in either the choke or start throttle positions
the cutting equipment starts to rotate
immediately.
• Store and transport the machine and fuel so that any leakage
or fumes do not risk coming into contact with sparks or
naked flames. For example, electric machines, electric
motors, electrical switches/power switches, heaters or the
like.
!
• The complete clutch cover with shaft must be fitted before
the machine is started, otherwise the clutch can become
loose and cause personal injury.
• When storing and transporting fuel approved containers
intended for this purpose must be used.
• Never start the machine indoors. Bear in mind the dangers
of inhaling the engine‘s exhaust fumes.
• When storing the machine for long periods the fuel tank
must be emptied. Contact your local petrol station to find
out how to dispose of excess fuel.
• Observe your surroundings and make sure that there is no
risk of people or animals coming into contact with the
cutting equipment.
• Place the machine on the
ground, ensure the cutting
equipment runs free of
twigs and stones. Push the
machine body towards the
ground using your left
hand. (NOTE! Not with
your foot). Grip the starter
handle with your right
hand and pull the
WARNING!
Exercise great care when handling fuel.
Bear in mind the risk of fire, explosions and
inhaling fumes.
!
startercord.
8 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
General working instructions
Basic working techniques
• Always drop to idling speed after each working operation.
Longer periods running at full throttle without loading the
engine (that is without resistance, which the engine feels
from the cutting equipment when trimming) can lead to
serious engine damage.
IMPORTANT INFORMATION
•
•
This section takes up the basic safety
precautions for working with the trimmer.
If you encounter a situation where you are
uncertain how to proceed you should ask an
expert. Contact your dealer or your service
workshop.
WARNING!
Sometimes branches, grass or wood can
!
get caught between the guard and cutting
equipment. Always stop the engine when
cleaning.
•
Avoid all usage which you consider to be
beyond your capability.
Basic safety precautions
Grass trimming
using the trimmer
head and plastic
knifes
1.Observe your surroundings:
• To ensure that people, animals or other things cannot affect
your control of the machine.
• To ensure that the above mentioned do not come into
contact with the cutting equipment or objects that can be
thrown by the cutting equipment.
• Hold the trimmer head
just above the ground at
an angle. It is the end of
the cord that carries out
the work. Let the cord
work at its own pace. Do
not press the cord into the
area to be cut.
• NOTE! Never use a machine without the possibility of
calling for help in the event of an accident.
2.Avoid usage in
unfavourable weather
conditions. For example,
thick fog, heavy rain,
strong winds or extreme
cold, etc. To work in bad
weather conditions is
tiring and can create
dangerous circumstances,
e.g. slippery surfaces.
• The cord can easily
remove grass and weeds up
against walls, fences, trees
and borders, however, it
can also damage sensitive
bark on trees and bushes
and damage fence posts.
• Reduce the risk of
damaging plants by
shortening the cord to 10-
12 cm and reducing the
engine speed.
3.Make sure you can walk
and stand safely. Look out
for any obstacles with
unexpected movement
(roots, stones, branches,
pits, ditches, etc.). Take
great care when working
on sloping ground.
4.The engine should be switched off before moving. When
moving over longer distances and transporting the transport
guard should be used.
5.Never put the machine down with the engine running unless
you have good sight of it.
6.. Do not over-reach
7.Keep Cutting attachment below waist level.
English – 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Clearing
Trimming
• The clearing technique
removes all unwanted
vegetation. Keep the
trimmer head just above
the ground and tilt it.
Let the end of the cord
strike the ground around
trees, posts, statues and
the like. NOTE! This
technique increases the
wear on the cord.
• The trimmer is ideal to
cut grass that is difficult
to reach using a normal
lawn mower. Keep the
cord parallel to the
ground when cutting.
Avoid pressing the
trimmer head against the
ground as this can ruin
the lawn and damage the
tool.
• The cord wears quicker
and must be fed forward
more often when
working against stones,
brick, concrete, metal
fences, etc. than when
coming into contact
with trees and wooden
fences.
• Do not allow the
trimmer head to
constantly come into
contact with the ground
during normal cutting
procedures. Constant
contact can cause damage
and wear to the trimmer
head.
• When trimming and
clearing you should use
less than full throttle so
that the cord lasts longer
and to reduce the wear
on the trimmer head.
Sweeping
• The rotating cord‘s
fanning effect can be
used for quick and easy
cleaning. Hold the cord
parallel to and above the
area to be swept and
move the trimmer from
side to side.
• When cutting and
sweeping you should use
full throttle to obtain the
best results.
WARNING!
The bevel gear unit can get hot during use
!
!
and may remain so for a while afterwards.
There is a risk of slight burns if you touch it.
WARNING!
Warning for thrown objects. Always wear
protective glasses. Never lean over the
guard. Stones, rubbish, etc. can be thrown
up into the eyes causing blindness or
serious injury.
Keep unauthorised persons at a distance.
Children, animals, onlookers and helpers
should be kept outside the safety zone of
15 m (50 feet). Stop the machine
immediately if anyone approaches.
10 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
L-X/L-XT
25
L-XT
C/C-X
=
¥
¢
What is what on the trimmer?
15. Air filter cover
16. Clutch cover
1. Trimmer head
2. Grease filler cap
3. Angle gear
17. Handlebar adjustment
18. Locking nut
4. Spray guard
5. Shaft
19. Support flange
20. Drive disc
6. Loop handlebar
7. Throttle
21. Socket spanner
22. Operator‘s Manual
23. Allen key
8. Stop switch
9. Throttle trigger lock
10. Cylinder cover
11. Starter handle
12. Fuel tank
24. Locking pin
25. Shaft coupling
13. Choke
14. Air purge
English – 11
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembling the loop handlebar
(322C, 325CX)
Assembling and dismantling the
two-part shaft (325L-XT)
• Position the handle on
the shaft. Note that the
handle must be mounted
below the arrow on the
shaft.
Assembling:
• Make sure the handle is
loose.
• Guide the cut-out on the
lower section of the shaft
into the coupling‘s
• Fit the bolt, securing plate
and wing nut as shown in
the diagram.
locking plate on the
upper section of the
• Tighten the wing nut.
shaft. The sections are
then locked together.
• Tighten the handle.
Dismantling
• Undo the handle (at least
three turns).
• Press the handle towards
the coupling.
• Carefully twist the lower
section out of the lock.
Assembling the loop handlebar
(322L, 325L-X/L-XT)
• Hold both parts of the
shaft and pull out the
lower section from the
coupling.
• Clip the loop handle onto
the shaft. Note that the
loop handle must be
fitted between the arrows
on the shaft.
Assembly of the trimmer head
It is extremely important
that the disc drive’s/support
flange’s guide engages
correctly in the cutting
equipment’s centre hole
when assembling the cutting
equipment. Cutting
equipment assembled
incorrectly can result in
serious and/or fatal personal
injury.
• Slide the spacer into the
slot in the loop handle.
• 322L: Fit the nut, washer
and bolt.
325L-X/L-XT: Fit the
nut, knob and bolt. Do
not overtighten.
• Now adjust the trimmer
to give a comfortable
working position. Tighten
the bolt/knob.
WARNING!
Under no circumstances may the cutting
equipment be used without an approved
!
guard fitted. See the chapter “Technical
data”. If the wrong guard or a defective
guard is fitted this can cause serious
personal injury.
12 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembling the spray guard and
trimmer head Superauto II (322L,
325L-X/L-XT)
• Fit the appropriate guard
(A) for use with the
trimmer head. Hook the
guard onto the shaft fitting
and secure it with the bolt
(L).
Assembling other guards and cutting
equipment (322L, 325L-X/L-XT)
• Fit the appropriate
guard (A) for use with
the trimmer head. Hook
the guard onto the shaft
fitting and secure it with
the bolt (L).
• Fit the drive disc (B) on the
output axle.
• Fit the disc drive (B) on
the output axle.
• Turn the blade axle until
one of the holes in the
drive disc aligns with the
hole in the gear housing.
• Insert the locking pin (C)
in the hole so that the axle
is locked.
• Turn the blade axle until
one of the disc drive’s
holes aligns with the
corresponding hole in
the gear housing.
H
• The trimmer head must be
split to be fitted (see the
diagram). Proceed as
• Insert the locking pin
(C) into the hole to lock
the axle.
K
follows:
• Insert your finger into the
• Screw on the trimmer
head (H) in the
direction of rotation.
J
centre hole of the cover (I)
at the same time as you
hold the cover with your
other fingers. Press the two
catches (J) that extend from
the cut-out on the bottom
section (K) using the
I
• Dismantling takes place
in the reverse order.
K
thumb and index finger of
your other hand. Press
apart the trimmer head
using the fingers on the
cover.
• Place the cover (I) and the
support flange (F) on the
output axle.
• Fit the nut (G). The
tightening torque of the
nut is 35-50 Nm (3,5-5
kpm). Use the socket
G
F
B
C
I
Fitting the spray guard and trimmer
head (322C)
Guard
• Fit the guard as shown
in the diagram. Tighten
securely.
A
Trimmer head
spanner in the tool kit.
Hold the handle of the
spanner as close to the
trimmer guard as possible.
The nut is tightened when
the spanner is turned
against the direction of
rotation (left-hand thread).
• Fit the trimmer head‘s
bottom section (K) on the
cover (I) by pressing the
two sections together with
the cut-outs on the bottom
section aligned with the
catches on the cover.
• Fit the dust cup on the
shaft. The nut must be
completely covered by
the dust cup.
• Hold the dust cup with
a spanner to prevent the
shaft from rotating.
• Screw the trimmer head
onto the shaft.
• To dismantle follow the
instructions in the reverse
order.
English – 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Fitting the spray guard and trimmer
head (325CX)
• Fit the guard as shown
in the diagram. Tighten
securely.
• Insert the locking pin
into the hole to lock the
axle.
• Screw the trimmer head
onto the shaft. Tighten
securely.
14 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Mixture
Fuel mixture
• Always mix gasoline and oil in a clean container intended
for fuel.
NOTE!
The machine is fitted with a two-stroke engine and must
always be run on a mixture of gasoline and two-stroke oil. It is
important to measure the quantity of oil accurately, to ensure
the correct mixture ratio. Small discrepancies in the amount of
oil have a great bearing on the proportions of the fuel mixture
when mixing small amounts of fuel.
• Always start by filling half the quantity of gasoline required.
Then add the entire oil quantity. Mix (shake) the fuel
mixture. Fill the remaining quantity of gasoline.
• Mix (shake) the fuel mixture carefully before filling in the
machine‘s fuel tank.
WARNING!
Always provide good ventilation when
• Do not mix more than max. one month’s supply of fuel.
!
Gasoline
handling fuel.
• If the machine is not used for a long period of time, the fuel
tank should be emptied and cleaned.
NOTE!
Always use high grade
unleaded oil mixed gasoline
(minimum 87 RON).
Leaded fuel will destroy the
catalytic converter and it
will no longer serve its
purpose.
• This engine is certified to operate on unleaded gasoline.
WARNING!
The catalytic converter muffler gets very hot
during and after use.This also applies
during idling. Be aware of the fire hazard,
especially when handling the saw near
flammable substances or vapours.
!
• This engine is certified to
operate on unleaded
gasoline.
Fuelling
WARNING!
The following precautions reduce the risk of
fire:
!
• The lowest recommended
octane rating is 87. If you
run the engine on lower
octane rating than 87 so-
called “knocking“ can
occur. This leads to an
increased engine
temperature, which can
result in a serious engine
breakdown.
Do not smoke or place any sources of heat
in the vicinity of the fuel. Never refuel when
the engine is running. Always stop the
engine and let it cool for a few minutes
before refuelling. Open the fuel cap slowly
when fuelling so that any over pressure is
released slowly.Tighten the fuel cap
carefully after refuelling. Always move the
machine from the fuelling place before
starting.
• Clean around the fuel
cap. Contamination in
the tank can disrupt
operations.
• When working at
continuous high revs a
higher octane rating is
recommended.
• Ensure that the fuel is
well mixed by shaking the
container before filling
Two-stroke oil
• For the best results use
HUSQVARNA two-
stroke oil, which has been
specially developed for
clearing saws and chain
saws.
the tank.
Min. 3 m
(10 ft)
Gasoline
Oil
2%(1:50)
Mixing ratio 1:50 (2%).
Lit.
5
10
15
20
Lit.
0,10
0,20
0,30
0,40
• Never use two-stroke oil
intended for water cooled
outboard motors, so-called
outboard motor oil.
US
gallon
US
fl. oz.
1
2 1/2
5
2 1/2
6 1/2
12 7/8
• Never use oil intended of
four-stroke engines.
English – 15
Download from Www.Somanuals.com. All Manuals Search And Download.
START AND STOP
Cold engine
IGNITION:
Control before starting
Set the stop switch to the
start position.
CHOKE:
For reasons of safety follow
these recommendations!
Set the choke control in the
choke position.
AIR PURGE:
• Check that the support
flange is not cracked due to
fatigue or due to being
tightened too much.
Discard the support flange
if it is cracked.
Press the air purge
diaphragm repeatedly until
fuel begins to fill the
diaphragm. The diaphragm
need not be completely
filled.
Warm engine
• Ensure the locking nut has
not lost its captive force.
The nut lock should have a
locking force of at least 1.5
Nm. The tightening
Use the same starting
procedure as for the cold
engine, but do not set the
choke control in the choke
position. The start throttle
position is obtained by
setting the choke control in
the choke position and then
returning it to its original
position.
torque of the locking nut
should be 35-50 Nm.
• Check that the trimmer
head and spray guard are
not damaged or cracked.
Replace the trimmer head
or spray guard if they are
exposed to impact or are
cracked.
Stop
The engine is stopped by
switching off the ignition.
WARNING!
When the engine is started with the choke
in the choke or start position the cutting
equipment starts to rotate immediately.
• Never use the machine
without a guard or spray
guard nor with a defective
guard.
!
Start
Press the machine body
against the ground using
your left hand (NOTE! Not
your foot). Grip the starter
handle, slowly pull out the
cord with your right hand
until you feel some resistance
(the starter pawls grip), now
quickly and powerfully pull
the cord.
Start and stop
Reset the choke control as
soon as the engine fires and
repeat until the engine starts.
When the engine starts
quickly apply full throttle
and the start throttle will
automatically disengage.
WARNING!
The complete clutch cover with shaft must
be fitted before the machine is started,
otherwise the clutch can become loose
and cause personal injury.
Always move the machine from the filling
area before starting. Place the machine on
a flat surface. Ensure the cutting
equipment cannot come into contact with
any object. Make sure no unauthorised
persons are in the working area,
otherwise there is a risk of serious
personal injury.The safety distance is 15
metres.
!
NOTE! Do not pull the
starter cord out completely
and do not release the starter
cord from the fully extended
position. This can damage
the machine.
16 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Basic setting
Carburetor
Your Husqvarna product has been designed and
• The carburetor is set to its basic setting when test run at the
factory. The basic setting should be kept during the
machine‘s first working hours. Thereafter the carburetor
should be finely adjusted. Fine adjustment should be carried
out by a skilled technician.
manufactured to specifications that reduce harmful
emissions.
After your unit has been run 8-10 tanks of fuel the engine
has broken in. To ensure that your unit is at peak
performance and producing the least amount of harmful
emissions after break in, have your authorized servicing
dealer, who has a revolution counter at his disposal, to adjust
your carburetor for optimum operating conditions.
NOTE! If the cutting attachment rotates/moves while the
engine is idling the T-screw should be turned anti-clockwise
until the cutting attachment stops.
Rec. idling speed: 2 700 rpm.
WARNING!
The complete clutch cover with shaft
Recommended max. speed: See “Technical Data” .
!
must be fitted before the machine is
started, otherwise the clutch can become
loose and cause personal injury.
WARNING!
If the idling speed cannot be adjusted so
that the cutting attachment stops,
!
Operation
contact your service workshop. Do not
use the machine until it has been
correctly adjusted or repaired.
• The carburetor governs
the engine‘s speed via the
throttle. Air/fuel is mixed
in the carburetor. The
air/fuel mixture is
adjustable. To take
advantage of the engine‘s
optimal output the
adjustment must be
correct.
Fine adjustment
• When the machine has been ”run-in” the carburetor should
be finely adjusted. The fine adjustment should be carried
out by qualified person. First adjust the L-jet, then the
idling screw T and then the H-jet.
Conditions
• Before any adjustments are made the airfilter should be clean
and the airfilter cover fitted. Adjusting the carburetor while
a dirty airfilter is in use will result in a leaner mixture when
the filter is finally cleaned. This can give rise to serious
engine damage.
• The setting of the
carburetor means that the
engine is adapted to local
conditions, for example,
the climate, altitude,
gasoline and the type of
2-stroke oil.
• Carefully turn the L and H needle to the mid point between
fully turned in and fully turned out..
• Do not attempt to adjust the needles beyond the stops as
damage can occur.
• Now start the machine according to the starting instructions
and run it warm for 10 minutes.
NOTE! If the cutting attachment rotates/moves the T screw
should be turned anti-clockwise until the cutting attachment
stops.
• The carburetor is
equipped with three
adjustment possibilities:
L = Low speed needle
H = High speed needle
T = Idle speed adjuster
screw
Low speed needle L
Try to find the highest idling
speed, turning the low speed
needle L clockwise
• The fuel quantity in relation to the air flow permitted by the
throttle opening is adjusted using the L and H-needles.
Turning the needles clockwise gives a leaner fuel mixture
(less fuel) and turning them anti-clockwise gives a richer fuel
mixture (more fuel). A leaner mixture gives high revs while a
richer mixture give less revs.
respectively counter-
clockwise. When the highest
speed has been found, turn
the low speed needle L 1/4
turn counter-clockwise.
NOTE! If the cutting
• The T-screw regulates the position of the throttle while the
engine is idling. Turning the screw clockwise gives a higher
idling speed while turning it anti-clockwise gives a lower
idling speed.
attachment rotates/moves in
+ 1/4
the idling position, turn the
idling speed screw T
counter-clockwise until the
cutting attachment stops.
L
English – 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Correctly adjusted carburetor
Final setting of the idling speed T
Adjust the idling speed with
the screw T, if it is necessary
to readjust. First turn the
idle speed adjusting screw T
clockwise until the cutting
attachment starts to rotate/
move.
A correctly adjusted carburetor means that the machine
accelerates without hesitation and the machine 4-cycles a
little at max speed. Furthermore, the cutting attachment
must not rotate/move at idling. A too lean adjusted low
speed needle L may cause starting difficulties and bad
acceleration.
A too lean adjusted high speed needle H gives lower power
= less capacity, bad acceleration and/or damage to the
engine.
Then turn, counter-clock-
wise until the cutting
A too rich adjustment of the two speed needles L and H
gives acceleration problems or too low working speed.
attachment stops. A correctly
adjusted idle speed setting
occurs when the engine runs
smoothly in every position.
It should also be good
margin to the rpm when the
cutting attachment starts to
rotate/move.
CAUTION! Contact your servicing dealer, if the idle speed
setting cannot be adjusted so that the cutting attachment
stops. Do not use the machine until it has been properly
adjusted or repaired.
High speed needle
H
The high speed needle
affects the machine’s power,
speed, temperature and fuel
consumption. A too lean
adjustment on the high
speed needle H (the high
speed needle H is screwed in
too much) gives a too high
speed resulting in engine
damage. Do not allow the
engine to run at full speed
for more than 10 seconds.
Apply full throttle and turn
the high speed needle H
slowly anticlockwise until
the engine runs unevenly.
The high speed needle H is
then turned slowly
clockwise a little until the
engine runs smoothly.
Note the engine should be
run unloaded when
adjusting the high speed
H
needle.
Therefore dismantle the cutting equipment, nut, support
flange and disc drive before adjusting the high speed needle.
The high speed needle is adjusted correctly when the machine
‘splatters’ a little . If the machine smokes heavily at the same
time as it ‘splatters’ heavily the adjustment is too rich.
NOTE! For optimum setting of the carburetor, contact a
qualified servicing dealer who has a revolution counter at his
disposal.
18 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Muffler
Cooling system
NOTE!
To maintain as low opera-
ting temperature as possible
the engine is equipped with
a cooling system.
Some mufflers are fitted with a catalytic converter. See
“Technical data” to see whether your machine is fitted with a
catalytic converter.
4
The cooling system consists
of:
1.An air intake on the
starter unit.
The muffler is designed to
dampen the noise level and
to direct the exhaust fumes
away from the user. The
exhaust fumes are hot and
can contain sparks, which
can result in fire if the
3
2
2.Cooling fins on the
flywheel.
1
3.Cooling fins on the
cylinder
exhaust fumes are directed
towards a dry and
4.Cylinder cover (leads cold
air onto the cylinder).
inflammable material. Some
mufflers are equipped with a
special spark arrest screen. If
your machine is fitted with
this type of screen it should
be cleaned regularly. This is
done using a wire brush. On
mufflers without a catalytic
converter the screen should
be cleaned weekly, or
Clean the cooling system using a brush at least once a week, in
difficult conditions more often.
A dirty or blocked cooling system leads to the engine
overheating resulting in damage to the cylinder and piston.
Spark plug
replaced if necessary. On
mufflers fitted with a
catalytic converter the
The condition of the spark
plug is affected by:
screen should be checked
and cleaned monthly. If the
screen is damaged it should
be replaced. If the screen is
frequently blocked, this can
be a sign that the function
of the catalytic converter is
impaired. Contact your
dealer to inspect the muffler.
A blocked screen will cause
the engine to overheat
• An incorrect carburetor
setting.
• An incorrect fuel
mixture (too much or
faulty oil).
0,5 mm
• A dirty air filter.
These factors cause
deposits on the spark plug
electrode that may result in
malfunction or starting
resulting in damage to the
cylinder and piston. Also see
under “Maintenance”.
difficulties.
If the machine is low on power, difficult to start or runs
poorly while idling always check the spark plug first.
If the spark plug is dirty, clean it and at the same time check
that the electrode gap is 0.5 mm. The spark plug should be
changed after about one month of operation or earlier if
necessary.
NOTE!
Never use a machine with a defective muffler.
NOTE! Always use the recommended type of spark plug. An
incorrect spark plug can damage the cylinder/piston.
WARNING!
Mufflers fitted with catalytic converters
become extremely hot during use and
after stopping.This also applies at idling
speeds. Contact can result in burns to
the skin. Be observant to the risk of fire!
!
Two-part shaft
The end of the drive axle in
the lower shaft should be
lubricated with grease every
30 hours. There is a risk that
the drive axle ends (splined
coupling) on two-part shafts
jam if they are not lubricated
regularly.
English – 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
NOTE: Use only HUSQVARNA replacement parts. Use of
Air filter
other brands of replacement parts can cause damage to your
unit or injury to the operator or others. Your warranty does
not cover damage or liability caused by the use of accessories
and/or attachments not specifically recommended by
HUSQVARNA.
The air filter should be
cleaned regularly removing
dust and dirt to avoid:
• carburetor malfunction
• starting problems
• reduced engine power
• unnecessary wear to
engine parts
Maintenance schedule
Below you will find some general maintenance instructions.
Daily maintenance
• abnormal fuel
• Check throttle trigger and throttle trigger lockout function.
• Check stop switch function.
• Check that blade/trimmer head does not rotate at idling.
• Clean the exterior of the machine.
consumption
Clean the filter after every
25 hours or more regularly
if operating conditions are
exceptionally dusty.
• Check that the harness is undamaged.
• Check the guard for damage or cracks.
• Change the guard in case of impacts or cracks.
• Check the trimmer head for cracks and chips or damage.
Replace if necessary.
• A non-balanced blade/trimmer head induces heavy
vibrations that may damage the machine.
• Check that the locking nut is sufficiently tightened.
• Check that nuts and screws are sufficiently tightened.
Cleaning the air filter
Dismantle the air filter cover and remove the air filter. Wash in
clean, warm soapy water. Ensure that the filter is dry before
refitting. An air filter used for a long period of time can never
be cleaned completely. Therefore it is necessary to replace the
filter from time to time with a new filter. A damaged air filter
must always be replaced.
If the machine is used in dusty conditions the air filter
should be soaked in oil, see the section on “Oiling the air
filter“.
Weekly maintenance
• Check the starter, especially cord and return spring.
• Clean the carburetor area.
• Clean the exterior of the spark plug.
• Remove it and check the electrode gap.
• Adjust it to 0,5 mm (.020"), or change the spark plug.
• Clean the cooling fins on the cylinder and check that the air
intake at the starter is not clogged.
• Check that the angle gear is filled with grease up to 3/4. Use
special grease.
• Clean the air filter.
• Clean or replace the muffler’s spark arrest screen (only
mufflers with a catalytic converter).
Oiling the air filter
Always use HUSQVARNA
filter oil, order no. 503 47
73-01. The filter oil
contains a solvent to make
it spread evenly through
the filter. You should
therefore avoid skin
contact. Put the filter in a
plastic bag and the pour
the filter oil over it. Knead
the plastic bag to distribute
the oil. Squeeze the excess
oil out of the filter inside
Monthly maintenance
• Clean the fuel tank.
• Clean the exterior of the carburetor and the space around it.
• Clean the fan and the space around it.
• Check fuel hose for cracks or other damage. Change if
necessary.
the plastic bag and pour
off the excess before fitting
the filter on the machine. Never use common engine oil. This
would drain through the filter quite quickly and collect in the
bottom.
• Change fuel filter in fuel tank.
• Check clutch, clutch spring and clutch drum for wear.
Change if necessary.
• Check electrical wires and connections.
• Change the spark plug.
• Change the airfilter.
• Check and clean the muffler’s spark arrest screen if necessary
(only mufflers with a catalytic converter).
Angle gear (322L, 325L-X/L-XT)
The angle gear is filled with
a sufficient quantity of
grease at the factory.
However, before using the
machine you should check
that the angle gear is filled
to 3/4 with grease. Use
special grease.
Normally, the grease does
not need to be changed
except when repairs are
carried out.
20 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
322C
322L
325L-X/L-XT
Engine
Cylinder capacity, cu. in/cm3
Cylinder bore, inch/mm
1,33/21,7
1,26/32
1,33/21,7
1,26/32
1,50/24,5
1,34/34
Stroke length, inch/mm
1,06/27
1,06/27
1,06/27
Recommended max. speed, rpm
Idling speed, rpm
11 000 - 11 700
2 700
11 000 - 11 700
2 700
11 000 - 11 700
2 700
Speed of output axle, rpm
11 700
8 014
8 014
Max. engine output, acc. to ISO 8893
Catalytic converter muffler
Speed-regulated ignition system
Ignition system
0,7 kW/ 9 000 rpm
Yes
-
0,7 kW/ 9 000 rpm
Yes
Yes
0,9 kW/ 9 000 rpm
Yes
Yes
Manufacturer/type of ignition system
Spark plug
Electrode gap, inch/mm
Walbro MB 18
Champion RCJ 7Y
0,02/0,5
Walbro MB 20
Champion RCJ 7Y
0,02/0,5
Walbro MB 20
Champion RCJ 7Y
0,02/0,5
Fuel lubrication system
Manufacturer/type of carburetor
Fuel tank capacity, US pint/litres
Weight
Zama C1Q
1,06/0,5
Zama C1Q
1,06/0,5
Zama C1Q
1,06/0,5
Weight without fuel, cutting tool and
guard, Lbs/kg
8,8/4,0
8,4/3,8
9.0/4,1 L-XT: 9,7/4,4
Noise levels
Equivalent noise pressure level at the user’s
ear, measured according to EN 31806 and
ISO 7917, dB(A), min/max:
Equivalent noise power level at the user’s
ear, measured according to EN 31806 and
ISO 10884, dB(A), min/max:
Vibration levels
91/94
92/98
92/98
103/105
109/109
109/109
Vibration levels on the handles, measured
according to EN 31806 and ISO 7916, m/s
When idling, left/right handles, min:
When idling, left/right handles, max:
At max. speed, left/right handles, min:
At max. speed, left/right handles, max:
1,8/1,8
3,2/2,2
4,4/3,3
5,5/4,6
1,5/1,4
2,0/1,8
2,5/4,8
4,9/8,0
1,5/1,4 L-XT: 1,5/1,4
2,0/1,8 L-XT: 2,4/2,2
2,5/4,8 L-XT: 2,5/4,8
4,9/8,0 L-XT: 5,8/7,6
NOTE!
Noise and vibration measurements are made with all the machine’s approved cutting equipment fitted.
The table indicates the highest and lowest values.
Approved accessories
Thread blade shaft M10 (L, L-X, L-XT)
Thread blade shaft 3/8 (R) (322C)
Plastic knifes
Type
Cutting attachment guard Art No.
Tricut ∅ 300 mm (322L, 325L-X/L-XT)
Trimmy Hit VI (R) (322C)
503 93 42-02
Trimmer head
530 05 37-99 / 537 07 67-01
503 97 71-01 / 503 93 42-02
503 97 71-01 / 503 93 42-02
503 97 71-01 / 503 93 42-02
503 97 71-01 / 503 93 42-02
503 97 71-01 / 503 93 42-02
537 07 67-01
Trimmy H II 1" (322L, 325L-X/L-XT)
Trimmy Fix (322L, 325L-X/L-XT)
Trimmy Hit (322L, 325L-X/L-XT)
Trimmy Hit Pro (322L, 325L-X/L-XT)
Superauto II 1" (322L, 325L-X/L-XT)
Trimmy Hit Junior (R) (322C)
English – 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
325CX
Engine
Cylinder capacity, cu. in/cm3
Cylinder bore, inch/mm
1,50/24,5
1,34/34
Stroke length, inch/mm
1,06/27
Recommended max. speed, rpm
Idling speed, rpm
11 000 - 11 700
2 700
Speed of output axle, rpm
11 700
Max. engine output, acc. to ISO 8893
Catalytic converter muffler
Speed-regulated ignition system
Ignition system
0,9 kW/ 9 000 rpm
Yes
–
Manufacturer/type of ignition system
Spark plug
Electrode gap, inch/mm
Walbro MB 20
Champion RCJ 7Y
0,02/0,5
Fuel lubrication system
Manufacturer/type of carburetor
Fuel tank capacity, US pint/litres
Weight
Zama C1Q
1,06/0,5
Weight without fuel, cutting tool and
guard, Lbs/kg
9,3/4,2
Noise levels
Equivalent noise pressure level at the user’s
ear, measured according to EN 31806 and
ISO 7917, dB(A), min/max:
Equivalent noise power level at the user’s
ear, measured according to EN 31806 and
ISO 10884, dB(A), min/max:
Vibration levels
92/97
107/108
Vibration levels on the handles, measured
according to EN 31806 and ISO 7916, m/s
When idling, left/right handles, min:
When idling, left/right handles, max:
At max. speed, left/right handles, min:
At max. speed, left/right handles, max:
2,5/2,1
3,2/2,2
4,4/4,2
6,2/8,4
NOTE!
Noise and vibration measurements are made with all the machine’s approved cutting equipment fitted.
The table indicates the highest and lowest values.
Approved accessories
Thread blade shaft 3/8 (R)
Plastic knifes
Type
Cutting attachment guard Art No.
Tricut ∅ 230 mm (R)
Trimmy Hit VI (R)
Trimmy Fix (R)
537 07 67-01
537 07 67-01
537 07 67-01
537 07 67-01
Trimmer head
Trimmy Hit Junior (R)
22 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
EMISSION CONTROL WARRANTY STATEMENT
WHAT IS COVERED
YOUR WARRANTY RIGHTS AND
REPAIR OR REPLACEMENT OF PARTS
OBLIGATIONS
Repair or replacement of any warranted part will be perfor-
The EPA (The US Environmental Protection Agency),
Environment Canada and Husqvarna Forest & Garden are
pleased to explain the emissions control system warranty on
your 1999 and later small nonroad engine. In U.S., new small
nonroad engines must be designed, built and equipped to
meet the federal stringent anti-smog standards. Husqvarna
Forest & Garden must warrant the emission control system
on your small nonroad engine for the periods of time listed
below provided there has been no abuse, neglect or
improper maintenance of your unit. Your emission control
system includes Parts such as the carburetor and the ignition
system.
med at no charge to the owner at an approved Husqvarna
Forest & Garden servicing dealer. If you have any questions
regarding your warranty rights and responsibilities, you
should contact your nearest authorized servicing dealer or
call Husqvarna Forest & Garden at 1-800-487-5963.
WARRANTY PERIOD
Any warranted part which is not scheduled for replacement
as required maintenance, or which is scheduled only for
regular inspection to the effect of ”repair or replace as
necessary” shall be warranted for 2 years. Any warranted
part which is scheduled for replacement as required
maintenance shall be warranted for the period of time up to
the first scheduled replacement point for that part.
DIAGNOSIS
The owner shall not be charged for diagnostic labor which
leads to the determination that a warranted part is defective,
if the diagnostic work is performed at an approved
Husqvarna Forest & Garden servicing dealer.
CONSEQUENTIAL DAMAGES
Husqvarna Forest & Garden may be liable for damages to
other engine components caused by the failure of a
warranted part still under warranty.
Where a warrantable condition exists, Husqvarna Forest &
Garden will repair your small nonroad engine at no cost to
you. Expenses covered under warranty include diagnosis,
parts and labor.
MANUFACTURER’S WARRANTY
COVERAGE
The 1999 and later small nonroad engines are warranted for
two years. If any emission related part on your engine (as
listed above) is defective, the part will be repaired or
replaced by Husqvarna Forest &
Garden.
WHAT IS NOT COVERED
All failures caused by abuse, neglect or improper
maintenance are not covered.
OWNER’S WARRANTY
RESPONSIBILITIES
ADD -ON OR MODIFIED PARTS
As the small nonroad engine owner, you are responsible for
the performance of the required maintenance listed in your
Operator’s Manual. Husqvarna Forest & Garden
recommends that you retain all receipts covering
maintenance on your small nonroad engine, but Husqvarna
Forest & Garden cannot deny warranty solely for the lack of
receipts or for your failure to ensure the performance of all
scheduled maintenance.
As the small nonroad engine owner, you should, however, be
aware that Husqvarna Forest & Garden may deny you
warranty coverage if your small nonroad engine or a part of it
has failed due to abuse, neglect, improper maintenance,
unapproved modifications or the use of parts not made or
approved by the original equipment manufacturer.
You are responsible for presenting your small nonroad
engine to a Husqvarna Forest & Garden authorized servicing
dealer as soon as a problem exists. The warranty repairs
should be completed in a reasonable amount of time, not to
exceed 30 days.
The use of add-on or modified parts can be grounds for
disallowing a warranty claim. Husqvarna Forest & Garden is
not liable to cover failures of warranted parts caused by the
use of add-on or modified parts.
HOW TO FILE A CLAIM
If you have any questions regarding your warranty rights and
responsibilities, you should contact your nearest authorized
servicing dealer or call Husqvarna Forest & Garden at
1-800-487-5963.
WHERE TO GET WARRANTY SERVICE
Warranty services or repairs shall be provided at all
Husqvarna Forest & Garden authorized servicing dealers.
MAINTENANCE, REPLACEMENT AND
REPAIR OF EMISSION-RELATED PARTS
Any Husqvarna Forest & Garden approved replacement part
used in the performance of any warranty maintenance or
repairs on emission-related parts, will be provided without
charge to the owner if the part is under warranty.
If you have any questions regarding your warranty rights and
responsibilities, you should contact your nearest authorized
servicing dealer or call Husqvarna Forest & Garden at 1-800-
487-5963.
WARRANTY COMMENCEMENT DATE
The warranty period begins on the date small nonroad
engine is delivered.
EMISSION CONTROL WARRANTY
PARTS LIST
1. Carburetor and internal parts
2. Intake pipe, airfilter holder and carburetor bolts.
3. Airfilter and fuelfilter covered up to maintainance schedule.
4. Ignition System
a) Spark Plug, covered up to maintenance schedule
b) Ignition Module
5. Muffler with catalytic converter
LENGTH OF COVERAGE
Husqvarna Forest & Garden warrants to the initial owner and
each subsequent purchaser that the engine is free from
defects in materials and workmanship which cause the
failure of a warranted part for a period of two years.
MAINTENANCE STATEMENT
The owner is responsible for the performance of all required
maintenance, as defined in the operator’s manual.
English – 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Super Auto II
Super Auto II 1
"
1
2
3
6
4
5
4,0 m
13'
15 cm
~2,0 m
6,5
6
"
'
15 cm
6
8
7
"
9
10
24 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
Tri Cut
1
2
>20mm
B
A
3
4
5
>20mm
7
6
6 Nm
!
8
X 10
English – 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimmy H II
1
2
3
4
15 cm
6"
7,5 m
25'
~ 3,7 m
12'
7
5
6
8
9
2
1
15 cm
6"
26 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimmy Hit
1
2
3
4
“Click”
7,0 m
23'
12 cm
5"
~ 3,5 m
11'
5
6
9
7
8
“Click”
~ 15 cm
6
"
10
11
15 cm
6
"
English – 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimmy Hit Junior
1
2
3
4
5,75 m
19'
15 cm
6"
~ 2,8 m
9'
5
6
9
7
8
15 cm
6"
11
10
12
1.)
2.)
15 cm
6"
“Click”
28 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimmy Hit Pro
1
2
3
4
7,5 m
25'
15 cm
6"
~ 3,7 m
12'
5
6
9
7
8
15 cm
6"
11
10
12
1.)
2.)
15 cm
6"
“Click”
English – 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimmy Hit VI
1
2
6
8
3
4
7,0 m
23'
12 cm
5"
~ 3,5 m
11'
5
~ 15 cm
"
9
7
6
“Click”
10
11
15 cm
"
6
30 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimmy SII
1
2
7,0 m
23'
12 cm
5"
~ 3,5 m
11'
3
4
~ 15 cm
7
5
6
6'
"Clic"
8
9
35-50 NM
English – 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimmy SII
~ 15 cm
6'
1
2
3
4
~ 15 cm
6'
502 26 04-01
502 25 56-01
502 25 53-01
729 53 27-71 (x3)
738 21 03-04
502 26 24-01 (x2)
740 43 14-00
502 26 03-01
502 25 52-01
502 26 01-01
735 31 19-00
502 27 07-01
502 26 86-01
32 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimmy VII
1
2
3
4
7,0 m 23"
12 cm 5"
~ 3,5 m 11"
5
6
7
8
9
1)
~ 15 cm 6"
2)
11
10
15 cm
6"
English – 33
Download from Www.Somanuals.com. All Manuals Search And Download.
´*313¶5r¨
34 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
´*313¶5r¨
2001W15
Download from Www.Somanuals.com. All Manuals Search And Download.
|