Husqvarna Lawn Mower Accessory 968999211 User Manual

Operator  
And  
Model:  
968999211 / CZ48  
Parts Manual  
For  
48 Inch Consumer Z  
Grass Catcher  
MANUAL NO. 1140207-26 REV. 01 (03/13/06)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
Safety Instructions  
These instructions are for your safety. Read them carefully.  
WARNING!  
This symbol means that important safety instructions need to be emphasized.  
It concerns your safety.  
General Use  
Read all instructions in this operator’s  
manual and on the machine before starting  
it. Ensure that you understand them and  
then abide by them.  
Learn how to use the machine and its  
controls safely and learn how to stop quickly.  
Also learn to recognize the safety decals.  
Only allow the machine to be used by adults  
who are familiar with its use.  
Make sure nobody else is in the vicinity of the  
machine when you start the engine, engage  
the drive, or run the machine.  
8011-512  
Read the operator’s manual before starting the  
machine  
Make sure animals and people maintain a  
safe distance from the machine.  
Stop the machine if someone enters the  
work area.  
Clear the area of objects such as stones,  
toys, steel wire, etc. that may become  
caught in the blades and thrown out.  
Beware of the discharge deck and do not  
point it at any one. Do not use the machine  
without the discharge deck in place.  
8011-513  
Stop the engine and prevent it from start-ing  
before you clean the discharge deck.  
Clear the area of objects before mowing  
Remember that the operator is responsible  
for dangers or accidents.  
Never take passengers. The machine is only  
intended for use by one person.  
Always look down and behind before and  
during reversing maneuvers. Keep a look out  
for both large and small obstacles.  
Slow down before turning.  
8011-520  
Shut down the blades when not mowing.  
Never take passengers  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
Be careful when rounding fixed objects, so  
that the blades do not hit them. Never drive  
over foreign objects.  
WARNING!  
Engine exhaust and certain  
vehicle components contain  
or emit chemicals considered  
to cause cancer, birth defects,  
or other reproductive system  
damage. The engine exhaust  
contains carbon monoxide,  
which is a colorless, poisonous  
gas. Do not use the machine  
in enclosed spaces.  
Only use the machine in daylight or in other  
well-lit conditions. Keep the machine a safe  
distance from holes or other irregularities in  
the ground. Pay attention to other possible  
risks.  
Never use the machine if you are tired, if  
you have consumed alcohol, or if you are  
taking other drugs or medication that can  
affect your vision, judgment, or  
coordination.  
Beware of traffic when working near or  
crossing a road.  
Never leave the machine unsupervised with  
the engine running. Always shut down the  
blades, pull back the parking brake, stop the  
engine, and remove the ignition key before  
leaving the machine.  
Never allow children or other persons not  
trained in the use of the machine to use or  
service it. Local laws may regulate the age  
of the user.  
8011-518  
Keep children away from the work area  
WARNING!  
When using the machine, approved personal protective equipment shall be  
used. Personal protective equipment cannot eliminate the risk of injury but it  
will reduce the degree of injury if an accident does happen. Ask your retailer  
for help in choosing the right equipment.  
Make sure that you have first aid equipment  
close at hand when using the machine.  
Never use the machine when barefoot.  
Always wear protective shoes or boots,  
preferably with steel toecaps.  
Always wear approved protective glasses or  
a full visor when assembling or driving.  
Never wear loose clothing that can get  
caught in moving parts.  
8011-292  
Personal protective equipment  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
Driving on Slopes  
Driving on slopes is one of the operations where the  
risk is greatest that the driver will lose control or the  
machine will tip over, which can result in serious  
injury or death. All slopes require extra caution. If  
you cannot reverse up a slope or if you feel unsure,  
do not mow the slope.  
Do as follows  
Remove obstacles such as stones,  
tree branches, etc.  
Mow up and down, not side-to-side.  
Never drive the rider on terrain that slopes more  
than 10°.  
Avoid starting or stopping on a slope. If the tires  
begin to slip, shut down the blades and drive  
slowly down the slope.  
8003-004  
Mow up and down, not side-to-side  
Always drive evenly and slowly on slopes.  
Make no sudden changes in speed or direction.  
Avoid unnecessary turns on slopes, and if it  
proves necessary, turn slowly and gradually  
downward, if possible.  
Watch out for and avoid driving over furrows,  
holes, and bumps. On uneven terrain, the  
machine can tip more easily. Long grass can  
hide obstacles.  
Drive slowly. Use small movements of the  
steering controls.  
Be extra cautious with any additional  
equipment, which can alter the machine’s  
stability.  
8011-519  
Be extra cautious when driving on slopes  
Do not mow near verges, ditches, or banks.  
The machine can suddenly spin around if a  
wheel goes over the edge of a drop or ditch, or  
if an edge gives way.  
Do not mow wet grass. It is slippery, and the  
tires can lose their grip, so that the machine  
slides.  
Try not to stabilize the machine by putting a foot  
on the ground.  
When cleaning the chassis, the machine may  
never be driven near verges or ditches.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
Children  
Serious accidents may occur if you fail to be  
on guard for children in the vicinity of the  
machine. Children are often attracted to the  
machine and mowing work. Never assume  
that children will stay put where you last saw  
them.  
Keep children away from the mowing area  
and under close supervision by another  
adult.  
Keep an eye out and shut off the machine if  
children enter the work area.  
Before and during a reversing maneuver,  
look backward and downward for small  
children.  
8011-517  
Never allow children to operate the machine  
Never allow a child to ride with you. They can  
fall off and injure themselves seriously or  
prevent risk-free maneuvering of the  
machine.  
Never allow children to operate the machine.  
Be particularly cautious near corners,  
bushes, trees, or other objects that block  
your view.  
WARNING!  
The engine must not be started when the driver’s floor plate or any protective  
plate for the mower deck’s drive belt is removed.  
Stop the engine. Prevent the engine from  
starting by removing the ignition key before  
making any adjustments or performing  
maintenance.  
Never fill the fuel tank indoors.  
Fuel and fuel fumes are poisonous and  
extremely flammable. Be especially cautious  
when handling fuel, as carelessness can  
result in personal injury or fire.  
Only store fuel in containers approved for the  
purpose.  
Never remove the fuel tank cap and never fill  
the fuel tank while the engine is running.  
8011-516  
Never fill the fuel tank indoors  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
Allow the engine to cool before refueling. Do  
not smoke. Do not fill fuel in the vicinity of  
sparks or open flames.  
WARNING!  
If leaks arise in the fuel system, the engine  
must not be started until the problem has been  
resolved.  
The engine, the exhaust system,  
and the hydraulic system’s  
components become very warm  
during operation.  
Store the machine and fuel in such a way that  
there is no risk of leaking fuel or fuel vapor  
leading to damages.  
Risk for burns if touched.  
Check the fuel level before each use and leave  
space for the fuel to expand, because the heat  
from the engine and the sun may otherwise  
cause the fuel to expand and overflow.  
Avoid overfilling. If you spill fuel on the machine,  
wipe up the spill and wait until it has evaporated  
before starting the engine. If you have spilled  
fuel on your clothing, change your clothing.  
WARNING!  
The battery contains lead and  
lead compounds, chemicals  
that are considered to cause  
cancer, birth defects, and  
other reproductive system  
damage. Wash your hands  
after touching the battery.  
Allow the machine to cool before taking any  
actions in the engine compartment.  
Be very careful when handling battery acid.  
Acid on skin can cause serious corrosive  
burns. If you spill battery acid on your skin,  
rinse immediately with water.  
Acid in the eyes can cause blindness, contact  
a doctor immediately.  
Be careful when servicing the battery.  
Explosive gases form in the battery. Never  
perform maintenance on the battery when  
smoking or near open flames or sparks. The  
battery can explode and cause serious injury/  
damage.  
Ensure that nuts and bolts, especially the  
fastening bolts for the blade attachments, are  
properly tightened and that the equipment is in  
good condition.  
Do not modify safety equipment. Check  
regularly to be sure it works properly. The  
machine must not be driven with defective or  
unmounted protective plates, protective  
cowlings, safety switches, or other protective  
devices.  
8011-563  
Do not smoke when performing maintenance on  
the battery. The battery can explode and cause  
serious injury/damage  
Do not change the settings of governors and  
avoid running the engine with overly high  
engine speeds. If you run the engine too fast,  
you risk damaging the machine components.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
Never use the machine indoors or in spaces  
lacking proper ventilation. The exhaust fumes  
contain carbon monoxide, an odorless,  
poisonous, and lethal gas.  
Stop and inspect the equipment if you run over  
or into anything. If necessary, make repairs  
before starting.  
Never make adjustments with the engine  
running.  
The machine is tested and approved only with  
the equipment originally provided or  
recommended by the manufacturer.  
The blades are sharp and can cause cuts and  
gashes. Wrap the blades or use protective  
gloves when handling them.  
8011-515  
Never drive the machine in an enclosed space  
Check the parking brake’s functionality  
regularly. Adjust and service as necessary.  
The mulch deck shall only be used when  
higher quality mowing is desired in familiar  
areas.  
Reduce the risk of fire by removing grass,  
leaves, and other debris that may have  
accumulated on the machine. Allow the  
machine to cool before putting it in storage.  
Transport  
The machine is heavy and can cause serious  
crushing injuries. Be extra cautious when it is  
loaded on or unloaded from a vehicle or trailer.  
8011-514  
Clean the machine regularly  
Use an approved trailer to transport the  
machine. Activate the parking brake, turn off  
the fuel supply, and fasten the machine with  
approved fastening devices, such as bands,  
chains, or ropes, when transporting.  
IMPORTANT INFORMATION  
The parking brake is not sufficient to  
lock the machine in place during  
transport. Ensure that the machine is  
well fastened to the transport vehicle.  
Reverse the machine onto the transport  
vehicle to avoid tipping it over.  
Check and abide by local traffic regulations  
before transporting or driving the machine on  
any road.  
Catcher  
DO NOT operate mower with grass catcher,  
unless the front weights are installed.  
Grass catcher components are subject to  
wear, damage, and deterioration, which  
could expose moving parts or allow objects  
to be thrown. Frequently check components  
and replace with manufacturer’s recom-  
mended parts, when necessary.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARTON CONTENTS  
UNPACKING INSTRUCTIONS  
CARTON CONTENTS:  
3 - Container Tops  
3 - Container Bottoms 4 - Bolts 3/8-16 x 4 1/2"  
2 - Straps  
Remove all parts and packing materials  
from carton.  
1 - Upper Chute  
1 - Lower Chute  
1 - Catcher Mount  
1 - Cover Assembly  
2 - Front Weights  
4 - Nuts 3/8-16, centerlock  
2 - Bolts 5/16-18 x 1 1/4"  
4 - Washers 5/16, flat  
2 - Washers, support  
2 - Nuts 5/16-18, nyloc  
Check carton contents against list. Be sure  
all parts are there.  
TOOLS REQUIRED FOR ASSEMBLY  
(2) 1/2" Wrenches  
(1) 9/16" Wrench  
(1) 9/16" Socket wrench  
PARTS IDENTIFICATION  
COVER  
ASSEMBLY  
DUMP BAG  
INDICATOR  
CHUTE LATCH  
UPPER CHUTE  
GRASS  
CATCHER  
CONTAINERS  
LOWER CHUTE  
ATTACHING  
STRAPS  
LOWER CHUTE  
NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you  
are seated on the mower in the operator’s position.  
CAUTION  
BEFORE ASSEMBLING GRASS CATCHER TO MOWER:  
• Set parking brake.  
• Place motion control levers in "NEUTRAL " position.  
• Turn ignition key "OFF" and remove key.  
• Make sure the blades and all moving parts have completely stopped.  
• Disconnect spark plug and place wire where it cannot come in contact with plug.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
MOUNTING COVER ASSEMBLY TO  
SUPPORT ASSEMBLY  
(See Figure 2)  
BAGGER SUPPORT ASSEMBLY  
(See Figures 1A and 1B)  
2
1
1. Remove rear engine guard by removing the  
six bolts that attach the guard to the frame.  
2. Attach hitch (Part No. 539108014) to the  
frame using the same holes and same six  
bolts that attached the rear engine guard.  
NOTE: For ease of assembly, you may wish to  
obtain the assistance of another person for  
mounting cover assembly to mower.  
1. Position cover assembly on ground behind  
mower as shown.  
2. Lift and rotate cover to align cover brackets  
with support assembly tubes.  
3. Slide cover assembly down onto the support  
tubes.  
*NOTE: If your unit does not have the holes or  
slots on the fenders, you will need to mark and  
drill them before continuing.  
FENDER  
ENGINE  
GUARD  
BOLTS  
3/8" HOLE*  
COVER  
ASSEMBLY  
REAR ENGINE GUARD  
3/8" HOLE*  
ENGINE  
GUARD  
BOLTS  
SUPPORT  
ASSEMBLY  
ENGINE  
GUARD  
BOLTS  
FIGURE 1A  
3. Using the hardware shown, attach the upper  
arms of the hitch to the rear fenders of the  
frame.  
WASHER, 5/16  
NUT, 5/16, NYLOC  
WASHER,  
SPECIAL  
HITCH  
NUT, 5/16, NYLOC  
WASHER, 5/16  
BOLT,  
WASHER, 5/16  
5/16-18 X 1 1/4  
WASHER,  
SPECIAL  
WASHER, 5/16  
BOLT,  
5/16-18 X 1 1/4  
FIGURE 1B  
FIGURE 2  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
CONTAINER MOUNTING  
(See Figure 4)  
CONTAINER ASSEMBLY  
(See Figure 3)  
4
3
1. Install one container to left side first with  
warning to the outside of unit. Install another  
container to center position and one in right  
position.  
1. Place bottom half inside of top half, as shown.  
2. Place one foot inside bottom half and lift top  
half to meet bottom half.  
3. Press halves tightly together while lifting top  
to lock into place as shown.  
NOTE: Right container should always overlap left  
container at center supports.  
IMPORTANT: BEFORE LOCKING THE TABS,  
HOOKED EDGES ON BOTH HALVES MUST  
OVERLAP TO FORM SEAL AS SHOWN IN IN-  
SET.  
2. Close cover and lock latch handles over  
center support tubes.  
COVER LATCH  
HANDLES  
CONTAINER  
BOTTOM  
HALF  
CONTAINER  
WARNING  
CENTER  
SUPPORT  
TUBES  
CONTAINER  
TOP HALF  
CONTAINER  
BOTTOM  
HALF  
CONTAINER  
WARNING  
PRESS TOGETHER  
TO FORM SEAL  
WHILE LIFTING  
TOP HALF  
CONTAINER  
HANDLE  
LOCKING  
TAB  
ASSEMBLY CHECK: Squeeze sides of lower half  
of container and check that there is no gap be-  
tween upper and lower halves. If a gap appears,  
unlock tabs to separate container halves and re-  
peat instructions above.  
WARNING  
DO NOT operate mower unless container  
is properly installed. Container is subject  
to wear and deterioration, check contain-  
ers frequently, replace when cracked or  
damaged. Use only a recommended re-  
placement container.  
FIGURE 4  
FIGURE 3  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
UPPER CHUTE  
(See Figures 6A & 6B)  
LOWER CHUTE  
(See Figure 5)  
5
6
1. Turn mower engine off.  
2. Raise and hold deflector shield in upright  
position.  
2. Place slot in lower chute over tab on mower  
deck and position lower chute over deck  
opening as shown.  
3. Hook rear latch into flange hole on back of  
mower deck.  
1. Lower mower deck to its lowest cutting  
position.  
2. Assemble upper chute by inserting curved  
end into hole in back of cover.  
NOTE: Handle carefully so as not to damage dump  
bag indicator.  
3. Push in and turn upper chute until it is in line  
with lower chute.  
4. Hook front latch into tab hole on front of  
mower deck.  
4. Align the bosses on lower chute with align-  
ment slots on upper chute with alignment  
slots on upper chute and slide together.  
5. Secure with rubber latch by hooking hole in  
latch over latch pin.  
CAUTION  
Before raising deflector shield, turn mower  
engine off. DO NOT remove deflector shield  
from mower. Raise and hold shield when at-  
taching lower chute and allow it to rest on  
chute while in operation.  
DUMP BAG  
UPPER  
CHUTE  
HANDLE  
INDICATOR  
COVER  
DEFLECTOR  
SHIELD  
LOWER  
CHUTE  
FIGURE 6A  
ALIGNMENT  
SLOT  
LATCH PIN  
RUBBER  
LATCH  
BOSSES  
T  
H  
FIGURE 6B  
LEVEL MOWER DECK  
7
Be sure deck is properly leveled for best mower  
performance. See your mower operator’s manual  
for instructions.  
REAR LATCH  
FIGURE 5  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
FRONT WEIGHTS  
(See Figure 8)  
8
1. Turn casters so they are facing the front as  
shown.  
2. Bolt the weights to the front tube of the frame  
as shown.  
CAUTION  
DO NOT operate mower with grass catcher,  
unless the front weights are installed.  
539990546  
(NUT, 3/8-16, CENTERLOC)  
539108154 (WHEEL WEIGHT)  
539990546  
(NUT, 3/8-16, CENTERLOC)  
539108154 (WHEEL WEIGHT)  
539108156 (STRAP)  
539108156 (STRAP)  
539990591  
(BOLT, 3/8-16 X 4 1/2)  
539990591  
(BOLT, 3/8-16 X 4 1/2)  
539990591  
(BOLT, 3/8-16 X 4 1/2)  
FIGURE 8  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TIPS FOR IMPROVED BAGGING OPERATION:  
Follow the mower operation instructions in you  
mower operator’s manual.  
Your bagger is equipped with a dump bag indi-  
cator. As the bags become full, the flow indi-  
cating ball will drop down in its slot, indicating  
that the bags are full or the chutes have be-  
come clogged. Care should be taken not to dam-  
age the parts and that the ball moves freely at  
the beginning of each use.  
If the grass catcher fails to pick up cut grass or  
leaves, it is an indication that clogging has oc-  
curred in the system or that the grass catcher  
containers are full.  
When operating your grass catcher on a lawn  
where grass and leaf bagging equipment has not  
been used, you are picking up thatch and debris  
that has accumulated for long periods of time. The  
amount collected and the total time of operation  
may be greater than you will experience with regu-  
lar use of your grass catcher.  
Always run throttle at full speed when bagging.  
Select a speed low enough to give good mower  
cutting performance, good quality cut and good  
bagging performance.  
a. Disengage blades, place motion control  
levers in neutral position.  
NOTE: It may be necessary to overlap width of  
cut to suit your conditions.  
- Unlatch and raise cover.  
- Slide out containers and dispose of clippings.  
- Replace containers, close cover, and latch.  
b. Unlatch chutes and check for clogging.  
- Remove all debris in chute.  
- Reassemble and latch chutes.  
c. Check to insure dump bag indicator has  
not become clogged.  
If grass is extremely tall, it should be mowed  
twice. The first time relatively high, the second  
time to desired height.  
Use left hand side of mower for trimming.  
Plastic trash bags (3.0 mil, 30 gallon) can be  
inserted inside grass catcher containers for  
ease of debris disposal. To remove the plastic  
trash bags when full:  
- The air passage hole must be clear of  
debris.  
Gently insert a small twig or wire into  
passageway to clear.  
a. Unlatch and raise cover.  
b. Remove one container at a time by grasp-  
ing container handles and pulling toward  
the rear, off of the tube rails.  
c. With the container resting on the ground,  
close and secure the top of the plastic lawn  
bag.  
CAUTION  
d. Tip the container on its side and slide the  
filled bag from the container.  
• DO NOT operate mower with grass  
catcher partially installed.  
e. Install a new plastic lawn bag with the  
edges of the bag draped over upper lip of  
the Container (for replacement bags refer  
to REPLACEMENT PARTS).  
• Disengage blades and stop engine be-  
fore leaving mower seat to empty con-  
tainers, unclogging chutes, etc.  
• Close cover before starting.  
f. Repeat for other containers.  
• Disengage mower blades when crossing  
driveways or gravel surfaces and other  
areas where thrown objects could be a  
hazard.  
g. Reinstall containers making sure right con-  
tainer overlaps left container at center sup-  
ports.  
h. Close cover and secure latches over cen-  
ter support tubes.  
• DO NOT attempt to vacuum up cans or  
other potentially hazardous projectiles.  
Avoid cutting wet grass or in the morning while  
the dew is still heavy. Grass clippings collected  
under these conditions tend to be sticky and  
adhere to the walls of the flow path causing  
clogging.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CUSTOMER RESPONSIBILITIES  
STORAGE:  
GENERAL RECOMMENDATIONS:  
When grass catcher is to be stored for a period of  
time, clean it thoroughly, remove all dirt, grass,  
leaves, etc. Store in a clean, dry place.  
Always observe safety rules when performing any  
maintenance.  
Before each use check for loose fasteners.  
Clean unit thoroughly after each use.  
BLADE CARE:  
CAUTION  
For best results mower blades must be kept sharp.  
Replace bent or damaged blades.  
Do not leave grass in bagger containers.  
Empty containers after each use and be-  
fore storing. Failure to do so may result in  
spontaneous combustion which could de-  
velop into a fire.  
See BLADE CARE instructions in your mow-  
er operator’s manual.  
CAUTION  
BEFORE PERFORMING ANY MAINTE-  
NANCE, SERVICE OR ADJUSTMENTS:  
• Set parking brake.  
• Place motion control levers in "NEU-  
TRAL" position.  
• Place clutch control in "DISENGAGED"  
position.  
• Turn ignition key to "OFF" position.  
• Make sure blades and all moving parts  
have completely stopped.  
• Disconnect spark plug wire(s) from spark  
plug(s) and place wire where it cannot  
come in contact with plug.  
CAUTION  
Grass catcher components are subject to  
wear, damage and deterioration, which  
could expose moving parts or allow objects  
to be thrown. Frequently check compo-  
nents and replace with manufacturer’s rec-  
ommended parts, when necessary.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS  
1
3
16  
4
30  
5
2
24  
6
8
30  
16  
16  
10  
16  
7
9
7
11  
12  
27  
29  
30  
28  
15  
14  
31  
16  
14  
16  
18  
31  
30  
17  
30  
42  
16  
7
10  
31  
16  
30  
23  
12  
20  
18  
22  
19  
23  
21  
21  
21  
25  
33  
36  
32  
35  
36  
33  
34  
33  
26  
32  
37  
38  
33  
41  
37  
34  
39  
39  
40  
40  
40  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS  
ITEM PART NO.  
QTY.  
DESCRIPTION  
1 ......... 532127533 .......... 1 ......... Screen, cover  
2 ......... 532134678 .......... 1 ......... Cover  
3 ......... 532176741 .......... 1 ......... Chute, upper  
4 ......... 818021008 .......... 1 ......... Screw, #10-14 x 1/2, special  
5 ......... 532140572 .......... 1 ......... Dump bag indicator  
6 ......... 532087175 .......... 1 ......... Screw, #10-24 x 1 1/8  
7 ......... 819061216 .......... 4 ......... Washer, 3/16 x 3/4 x 16 Ga.  
8 ......... 532007206 .......... 1 ......... Spacer, split  
9 ......... 532060867 .......... 1 ......... Nut, #10-24, acorn  
10 ....... 810071000 .......... 3 ......... Lockwasher  
11........ 532109808 .......... 1 ......... Latch, chute  
12 ....... 532125004 .......... 3 ......... Nut, weld  
14 ....... 532160793 .......... 2 ......... Latch, assembly  
15 ....... 532174345 .......... 1 ......... Chute, lower  
16 ....... 871161010 ........... 12........ Screw, #10-24 x 5/8  
17 ....... 532132796 .......... 1 ......... Spring, cover L.H. (black)  
18 ....... 532140809 .......... 2 ......... Spacer, cover  
19 ....... 532132983 .......... 1 ......... Spring, cover R.H. (gray)  
20 ....... 532085902 .......... 2 ......... Spring, retainer  
21 ....... 532174083 .......... 4 ......... Plug, tubing end  
22 ....... 532176990 .......... 1 ......... Bagger, frame  
23 ....... 532128600 .......... 2 ......... Pin, hinge  
24 ....... 532127534 .......... 1 ......... Gasket, cover  
25 ....... 532183286 .......... 3 ......... Container, top  
26 ....... 532129586 .......... 3 ......... Container, bottom  
27 ....... 532134637 .......... 1 ......... Seal, cover  
28 ....... 532130895 .......... 2 ......... Handle, bagger cover  
29 ....... 532155857 .......... 1 ......... Strip, reinforcement  
30 ....... 532069180 .......... 14........ Nut, #10-24, crownlock (not included with unit)  
31 ....... 871141008 ........... 5 ......... Screw, #10-24 x 1/2 (not included with unit)  
32 ....... 539106504 .......... 2 ......... Washer, special  
33 ....... 539990692 .......... 4 ......... Washer, 5/16  
34 ....... 539990627 .......... 2 ......... Bolt, 5/16-18 x 1 1/4  
35 ....... 539108014 .......... 1 ......... Hitch  
36 ....... 539990717 .......... 2 ......... Nut, 5/16-18, nyloc  
37 ....... 539990546 .......... 4 ......... Nut, 3/8-16, centerloc  
38 ....... 539108154 .......... 2 ......... Wheel weight  
39 ....... 539108156 .......... 2 ......... Strap  
40 ....... 539990591 .......... 4 ......... Bolt, 3/8-16 x 4 1/2  
41 ....... 539200732 .......... 1 ......... Decal, Husqvarna  
42 ....... 539108163 .......... 1 ......... Decal, warning catcher  
........... 532104419 ....................... Bag, 3.0 mil, 30 gal. trash, (not included with unit)  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Grizzly Lathe G8691 User Manual
Grizzly Saw G1023SLWX3 User Manual
Hans Grohe Plumbing Product 32111XX1 User Manual
Harbor Freight Tools Bicycle 94142 User Manual
Harbor Freight Tools Water Pump 95591 User Manual
Hasbro Games 59947 User Manual
Healthrider Home Gym HREX04980 User Manual
Honeywell Automobile Parts vc7900 User Manual
Hotpoint Clothes Dryer AQCF 852 BI User Manual
HP Hewlett Packard Stereo Amplifier 467A User Manual