Owner’s Manual
Installation and Operation
Model:
SLR (Cosmo)
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
WARNING
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• DO NOT store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
• What to do if you smell gas
- DO NOT try to light any appliance.
High temperatures may ignite clothing or other flammable
materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppli-
er’s instructions.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
- If you cannot reach your gas supplier, call
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions
and the manufactured home construction and safety standard,
Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory trained
professionals, or technicians supervised by an NFI
certified professional.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Used to address practices not related to personal injury.
Table of Contents
A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
B. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 5
6 Termination Locations
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 20
1 Listing and Code Approvals
7 Vent Information and Diagrams
A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
B. Tempered Glass Specifications . . . . . . . . . . . . . . . . . . . . . 6
C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . . 6
E. Non-Combustible Materials Specification. . . . . . . . . . . . . . 6
F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 6
G. Requirements for the Commonwealth of Massachusetts. . 7
A. Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
B. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
C. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
D. Measuring Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8 Vent Clearances and Framing
A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 31
B. Wall Penetration Framing. . . . . . . . . . . . . . . . . . . . . . . . . 31
C. Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . . 32
D. Install Attic Insulation Shield. . . . . . . . . . . . . . . . . . . . . . . 33
User Guide
2 Operating Instructions
A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
C. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
D. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . . 9
E. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
F. Remote Controls, Wall Controls and Wall Switches. . . . . . 9
G. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . 9
H. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 10
I. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
J. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 11
9 Appliance Preparation
A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
B. Securing and Leveling the Appliance. . . . . . . . . . . . . . . . 35
10 Installing Vent Pipe (SLP Pipe)
A. Assemble Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . . 36
B. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 37
C. Secure The Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . 37
D. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 38
E. Install Decorative Ceiling Components . . . . . . . . . . . . . . 38
F. Install Metal Roof Flashing. . . . . . . . . . . . . . . . . . . . . . . . 39
G. Assemble and Install Storm Collar. . . . . . . . . . . . . . . . . . 39
H. Install RF4-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
I. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 41
J. Install Decorative Wall Components . . . . . . . . . . . . . . . . 41
K. Heat Shield Requirements for Horizontal Termination . . . 41
L. Install Horizontal Termination Cap . . . . . . . . . . . . . . . . . . 42
3 Maintenance and Service
A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 12
B. Maintenance Tasks-Qualified Service Technician . . . . . . 13
Installer Guide
4 Getting Started
A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 14
B. Design and Installation Considerations . . . . . . . . . . . . . . 15
C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 15
D. Inspect Appliance and Components. . . . . . . . . . . . . . . . . 15
11 Gas Information
A. Fuel Conversion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . 44
5 Framing and Clearances
A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 16
B. Constructing the Appliance Chase. . . . . . . . . . . . . . . . . . 17
C. Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
D. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 18
12 Electrical Information
A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
B. Intellifire Ignition System Wiring. . . . . . . . . . . . . . . . . . . . 45
C. Optional Accessories Requirements . . . . . . . . . . . . . . . . 45
D. Electrical Service and Repair. . . . . . . . . . . . . . . . . . . . . . 46
E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 46
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
3
13 Finishing
A. Framing and Finishing Instructions . . . . . . . . . . . . . . . . . 47
B. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 50
C. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
D. Decorative Fronts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
14 Appliance Setup
A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 54
B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 54
C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
E. Rock Media Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . 55
F. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
G. Install the Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
H. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
15 Troubleshooting
A. Intellifire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 58
16 Reference Materials
A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 60
B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 61
C. Service Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Î = Contains updated information.
4
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Limited Lifetime Warranty
LIMITED LIFETIME WARRANTY
HEAT & GLO GAS APPLIANCE PRODUCTS
BASIC ONE-YEAR WARRANTY. HEAT & GLO, a brand of HEARTH & HOME TECHNOLOGIES INC., located at 20802 Kensington Boulevard,
Lakeville, MN 55044, (“HEAT & GLO”) warrants to the original owner that your new HEAT & GLO Gas Appliance (the “Product”) will be free
from defects in materials and workmanship for a period of one year from the date of installation. During the first year, HEAT & GLO will replace
or repair, at its discretion, any defective components at its sole cost and expense, including payment of all reasonable labor costs incurred in
replacing or repairing such components. This basic warranty is subject to the conditions, exclusions and limitations described below.
EXTENDED LIFETIME COVERAGE. HEAT & GLO warrants that the firebox, heat exchanger, log(s), and burner will not be defective in material
or workmanship during the period the Product is owned by the original owner, subject to the following conditions, exclusions and limitations
described below.
CONDITIONS, EXCLUSIONS AND LIMITATIONS:
1. This warranty applies to the original owner only and is nontransferable.
2. This warranty applies only to Products installed in the United States of America or Canada.
3. This warranty is limited to the replacement or repair of defective components or workmanship and HEAT & GLO may fully discharge all
obligations under this warranty by repairing or replacing, at its discretion, the defective components. The maximum amount recoverable
under this warranty is limited to the purchase price of the Product and, if HEAT & GLO is unable to provide replacement or repair in an
expedient and cost-effective manner, HEAT & GLO may discharge all obligations under this warranty by refunding the purchase price of
the Product. IN NO EVENT SHALL HEAT & GLO BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY
DEFECTS IN THE PRODUCT.
4. Any labor and related repair charges relating to the costs and expenses of replacing or repairing defective components under the Limited
Lifetime Warranty are not covered by this warranty, except as provided for under the Basic One-Year Warranty.
5. Components and parts made by other manufacturers, whether sold with the Product or added thereafter, are NOT covered by this war-
ranty unless expressly authorized and approved by HEAT & GLO in writing.
6. Any damages caused by environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure,
air handling devices such as exhaust fans or forced air furnaces, or other such causes are not covered by this warranty.
7. This warranty will be void if:
a) The Product is not installed, operated and maintained in compliance with local building codes and with the instructions in the Installer’s
Guide, Owner’s Guide and Listing Agent Identification Label furnished with the Product.
b) Any parts or components made by other manufacturers are added or used in the Product, unless expressly authorized and approved
by HEAT & GLO in writing.
c) Any service work is performed on the Product by anyone other than an authorized HEAT & GLO representative.
d) The Product is damaged due to shipping, improper handling, accident, abuse or misuse.
e) Fuels other than those specified in the Installer’s Guide and Owner’s Guide are used.
f) Modification was made to the Product which was not expressly authorized and approved by HEAT & GLO in writing.
EXCEPT TO THE EXTENT PROVIDED BY LAW, HEAT & GLO MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO THE DURATION OF THE WARRANTY SPECIFIED
ABOVE.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow exclusion or limitation of incidental or consequential
damages, so those limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which
vary from State to State.
If warranty service is needed you should contact your installing dealer and if the installing dealer is unable to provide necessary parts or
components, contact the nearest authorized HEAT & GLO dealer or supplier.
NOTES TO CUSTOMER:
1. In order to insure proper installation, operation and maintenance HEAT & GLO strongly recommends annual
servicing by an authorized HEAT & GLO dealer.
2. Please complete this information and retain this warranty in a safe place for future reference: Installation Date:___
Model #:_________________ Serial #:______________ Installing Contractor:_________________________
3. HEAT & GLO reserves the right to make changes at any time, without notice, in design, material, specifications
and prices of the Product. HEAT & GLO also reserves the right to discontinue styles and products.
© 2007 Hearth & Home Technologies Inc.
060-981E 10/07
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Listing and Code Approvals
1
A. Appliance Certification
C. BTU Specifications
Minimum
Input
BTU/h
Orifice
Size
(DMS)
Maximum
Input BTU/h
Models
MODEL: SLR
(U.S. or Canada)
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Vented Gas Fireplace Heater
US
(0-2000 FT)
26,000
21,870
25,000
23,500
N/A
N/A
N/A
N/A
#42
#43
.057
#54
SLR (NG)
SLR (LP)
CANADA
(2000-4500
FT)
STANDARD: ANSI Z21.88a-2007 CSA 2.33a-2007
Vented Gas Fireplace Heaters
US
(0-2000 FT)
This product is listed to ANSI standards for “Vented Gas
Fireplace Heaters” and applicable sections of “Gas Burn-
ing Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
CANADA
(2000-4500
FT)
NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemen-
tal room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
• In the USA: Reduce input rate 4% for each 1000 feet
above 2000 feet.
• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
B. Tempered Glass Specifications
Check with your local gas utility to determine proper
Hearth & Home Technologies appliances manufactured
with tempered glass may be installed in hazardous loca-
tions such as bathtub enclosures as defined by the Con-
sumerProductSafetyCommission(CPSC).Thetempered
glass has been tested and certified to the requirements
of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing
Certification Council SGCC# 1595 and 1597. Architectur-
al Testing, Inc. Reports 02-31919.01 and 02-31917.01).
orifice size.
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
This statement is in compliance with CPSC 16 CFR Sec-
tion 1201.5 “Certification and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certificate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750 ºC and UL763 shall be
considered non-combustible materials.
F. Combustible Materials Specification
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
Materials made of or surfaced with wood, compressed pa-
per, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or
unplastered shall be considered combustible materials.
Heat & Glo Quality Systems
registered by SGS ICS
6
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspection
Note: The following requirements reference various
Massachusetts and national codes not contained in this
document.
The state or local gas inspector of the side wall horizon-
tally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector ob-
serves carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
G. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above finished grade in the area of the venting, in-
cluding but not limited to decks and porches, the following
requirements shall be satisfied:
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fu-
eled equipment installed in a room or structure separate
from the dwelling, building or structure used in whole or
in part for residential purposes.
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addi-
tion, the installing plumber or gas fitter shall observe that
a battery operated or hard wired carbon monoxide detec-
tor with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
In the event that the side wall horizontally vented gas fu-
eled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
floor level.
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that dur-
ing said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not pro-
vide the parts for venting the flue gases, but identifies
“special venting systems”, the following requirements
shall be satisfied by the manufacturer:
• The referenced “special venting system” instructions
shall be included with the appliance or equipment in-
stallation instructions; and
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accor-
dance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certified.
• The “special venting systems” shall be Product Ap-
proved by the Board, and the instructions for that sys-
tem shall include a parts list and detailed installation
instructions.
Signage
A metal or plastic identification plate shall be permanent-
ly mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fu-
eled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) in. in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB-
STRUCTIONS”.
A copy of all installation instructions for all Product Ap-
proved side wall horizontally vented gas fueled equip-
ment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Common-
wealth of Massachusetts requirements.
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
7
User Guide
Operating Instructions
2
• Keep remote controls out of reach of children.
A. Gas Fireplace Safety
• Never leave children alone near a hot fireplace, whether
operating or cooling down.
WARNING
HOT SURFACES!
• Teach children to NEVER touch the fireplace.
Glass and other surfaces are hot during
operation AND cool down.
• Consider not using the fireplace when children will be
present.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
Contact your dealer for more information, or visit: www.
hpba.org/staysafe.
To prevent unintended operation when not using your fire-
place for an extended period of time (summer months,
vacations, trips, etc):
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
• Remove batteries from remote controls.
• Turn off wall controls.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
• Unplug 3 volt adapter plug and remove batteries on IPI
models.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
B. Your Fireplace
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
WARNING! DO NOT operate fireplace before read-
ing and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
If you expect that small children or vulnerable adults may
come into contact with this fireplace, the following precau-
tions are recommended:
• Install a physical barrier such as:
- A decorative firescreen.
- Adjustable safety gate.
• Install a switch lock or a wall/remote control with child
protection lockout feature.
DECORATIVE DOORS
(NOT SHOWN)
SECTION 2.D.
FIXED GLASS ASSEMBLY
(NOT SHOWN)
SECTION 14.K.
CLEAR SPACE
SECTION 2.C.
Figure 2.1 General Operating Parts
8
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Clear Space
E. Fixed Glass Assembly
WARNING! DO NOT place combustible objects in front
of the fireplace or block louvers. High temperatures may
start a fire. See Figure 2.2.
See Section 14.F.
F. Remote Controls, Wall Controls and Wall
Switches
Avoid placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.
Follow the instructions supplied with the control installed
to operate your fireplace:
For safety:
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
See your dealer if you have questions.
G. Before Lighting Fireplace
Before operating this fireplace for the first time, have a
qualified service technician:
• Verify all shipping materials have been removed from
inside and/or underneath the firebox.
• Review proper placement of logs, ember material and/or
other decorative materials.
• Check the wiring.
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
Figure 2.2 Clear Space
• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.
D. Decorative Doors and Fronts
WARNING! Risk of Fire or Asphyxiation! DO NOT op-
erate fireplace with fixed glass assembly removed.
WARNING! Risk of Fire! Install ONLY doors or fronts
approved by Hearth & Home Technologies. Unapproved
doors or fronts may cause fireplace to overheat.
Î
This decorative front has been supplied with an
integral barrier to prevent direct contact with the fixed
glass panel. DO NOT operate the fireplace with the
barrier removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.
For more information refer to the instructions supplied with
your decorative door or front.
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
9
H. Lighting Instructions (IPI)
The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery
life, remove them when using the transformer.
FOR YOUR SAFETY
READ BEFORE LIGHTING
LIGHTING
INSTRUCTIONS
(IPI)
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
1. Turn off all electric power to the appliance.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
A. This appliance is equipped with an
intermittent pilot ignition (IPI) device
which automatically lights the burn-
er. DO NOT try to light the burner by
hand.
2. This appliance is equipped with an ignition
device which automatically lights the burner.
DO NOT try to light the burner by hand.
• If you cannot reach your gas sup-
plier, call the fire department.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
GAS
VALVE
C. DO NOT use this appliance if any
part has been under water. Imme-
diately call a qualified service tech-
nician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
3. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” in the Safety
Information located on the left side of this la-
bel. If you do not smell gas, go to next step.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do
not use any phone in your building.
4. Turn on all electric power to the appliance.
WARNING: CAUTION:
5. To light the burner, flip the ON/OFF switch to
the “ON” position. (The ON/OFF switch may
include a wall switch if so equipped).
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gaso-
line and other liquids having flammable
vapors away.
DO NOT CONNECT 110 VAC TO
THE CONTROL VALVE.
6. If the appliance will not operate, follow the in-
structions “To Turn Off Gas to Appliance” and
call your service technician or gas supplier.
Improper installation, adjustment, al-
teration, service or maintenance can
cause injury or property damage. Re-
fer to the owner’s information manual
provided with this appliance.
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
TO TURN OFF
GAS TO APPLIANCE
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
1. Turn wall control or ON/OFF switch to “OFF”.
NOT FOR USE
WITH SOLID FUEL
2. Turn off all electric power to the appliance if
If not installed, operated, and main-
tained in accordance with the man-
ufacturer’s instructions, this product
could expose you to substances in fuel
or fuel combustion which are known to
the State of California to cause can-
cer, birth defects, or other reproductive
harm.
service is to be performed.
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
593-913F
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
For assistance or additional informa-
tion, consult a qualified installer, ser-
vice agency or the gas supplier.
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
Final inspection by
10
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
I. After Fireplace is Lit
Initial Break-in Procedure
• The fireplace should be run three to four hours
continuously on high.
• Turn the fireplace off and allow it to completely cool.
Î • Remove fixed glass assembly. See Section 14.F.
• Clean fixed glass assembly. See Section 3.
• Replace the fixed glass assembly and run continuously
on high an additional 12 hours.
This cures the materials used to manufacture the fire-
place.
NOTICE! Open windows for air circulation during fire-
place break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
J. Frequently Asked Questions
ISSUE
SOLUTIONS
This is a result of gas combustion and temperature variations. As the fireplace warms, this conden-
sation will disappear.
Condensation on the glass
This is a result of normal operation and the flames will begin to yellow as the fireplace is allowed to
burn for 20 to 40 minutes.
Blue flames
When first operated, this fireplace may release an odor for the first several hours. This is caused
by the curing of materials from manufacturing. Odor may also be released from finishing materials
and adhesives used near the fireplace. These circumstances may require additional curing related
to the installation environment.
Odor from fireplace
This is a normal result of the curing process of the paint and logs. Glass should be cleaned within
3 to 4 hours of initial burning. A non-abrasive cleaner such as gas appliance glass cleaner may be
necessary. See your dealer.
Film on the glass
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the
sound produced by a furnace or heating duct. This noise does not affect the operation or longevity
of the fireplace.
Metallic noise
There may be some “cracking” noise coming from the fireplace during the first few heating and
cooling cycles. This noise is associated with settling rock and some minor cracking of larger
pieces of rock. This will lessen over time as the glass rock is conditioned to the heating and cool-
ing temperature changes.
Rock noise
It is expected that a few small pieces (approximately 10 pieces) of rock may fall through the base-
pan and come to rest on the fireplace bottom. This has no affect on fireplace performance.
Rocks falling through basepan
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Maintenance and Service
3
Doors, Surrounds, Fronts
Any safety screen or guard removed for servicing must be
replaced prior to operating the fireplace.
Frequency: Annually
By: Homeowner
When properly maintained, your fireplace will give you
many years of trouble-free service. We recommend an-
nual service by a qualified service technician.
Tools needed: Protective gloves, stable work surface
• Assess condition of screen and replace as necessary.
A. Maintenance Tasks-Homeowner
• Inspect for scratches, dents or other damage and repair
as necessary.
Installation and repair should be done by a qualified service
technician only. The fireplace should be inspected before
use and at least annually by a professional service person.
• Check that louvers are not blocked.
• Vacuum and dust surfaces.
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service ap-
pointment.
Remote Control
Frequency: Seasonally
By: Homeowner
More frequent cleaning may be required due to lint from
carpeting or other factors. Control compartment, burner
and circulating air passageway of the fireplace must be
kept clean.
Tools needed: Replacement batteries and remote con-
trol instructions.
• Locate remote control transmitter and receiver.
• Verify operation of remote. Refer to remote control
operation instructions for proper calibration and setup
procedure.
CAUTION! Risk of Burns! The fireplace should be turned
off and cooled before servicing.
Glass Cleaning
Frequency: Seasonally
By: Homeowner
• Place batteries as needed in remote transmitters and
battery-powered receivers.
• Place remote control out of reach of children.
Tools Needed: Protective gloves, glass cleaner, drop
cloth and a stable work surface.
If not using your fireplace for an extended period of time
(summer months, vacations/trips, etc), to prevent unin-
tended operation:
CAUTION! Handle fixed glass assembly with care.
Glass is breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• Remove batteries from remote controls.
• Unplug 3 volt adapter plug on IPI models.
• DO NOT clean glass while it is hot
• Prepare a work area large enough to accommodate fixed
glass assembly and door frame by placing a drop cloth
on a flat, stable surface.
Note: Fixed glass assembly and gasketing may have res-
idue that can stain carpeting or floor surfaces.
• Remove door or decorative front from fireplace and set
aside on work surface.
Î • See Section 14.F for instructions to remove fixed glass
assembly.
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass
cleaner (consult with your dealer)
Î
• Refer to Section 14F for glass removal and replacement
instructions.
• Reinstall door or decorative front.
12
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
have penetrated the sheet metal are sharp and should
be avoided.
Venting
Frequency: Seasonally
By: Homeowner
• Remove all foreign objects.
• Verify unobstructed air circulation.
Tools needed: Protective gloves and safety glasses.
Burner Ignition and Operation
Frequency: Annually
• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.
By: Qualified Service Technician
• Verify termination cap clearance to subsequent construc-
tion (building additions, decks, fences, or sheds). See
Section 6.
Tools needed: Protective gloves, vacuum cleaner, whisk
broom, flashlight, voltmeter, indexed drill bit set, and a
manometer.
• Inspect for corrosion or separation.
• Verify burner is properly secured and aligned with pilot
or igniter.
• Verify weather stripping, sealing and flashing remains
intact.
• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.
• Inspect draft shield to verify it is not damaged or missing.
• Verify batteries have been removed from battery back-
up IPI systems to prevent premature battery failure or
leaking.
B. Maintenance Tasks-Qualified Service
Technician
• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.
The following tasks must be performed by a qualified ser-
vice technician.
• Inspect for lifting or other flame problems.
Gasket Seal and Glass Assembly Inspection
Frequency: Annually
Î
• Verify air shutter setting is correct. See Section 14.H for
required air shutter setting. Verify air shutter is clear of
dust and debris.
By: Qualified Service Technician
Tools needed: Protective gloves, drop cloth and a stable
work surface.
• Inspect orifice for soot, dirt and corrosion. Verify orifice
size is correct. See Service Parts List for proper orifice
sizing.
• Inspect gasket seal and its condition.
• Verify manifold and inlet pressures. Adjust regulator as
required.
• Inspect fixed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.
• Inspect pilot flame pattern and strength. See Figure 3.1
for proper pilot flame pattern. Clean or replace orifice
spud as necessary.
• Confirm there is no damage to glass or glass frame.
Replace as necessary.
• Verify that fixed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.
• Inspect IPI flame sensing rod for soot, corrosion and
deterioration. Clean with emery cloth or replace as
required.
Firebox
• Verify IPI millivolt output. Replace as necessary.
Frequency: Annually
By: Qualified Service Technician
• Verify that there is not a short in flame sense circuit by
checking continuity between pilot hood and flame sense
rod. Replace pilot as necessary.
Tools needed: Protective gloves, sandpaper, steel wool,
cloths, mineral spirits, primer and touch-up paint.
• Inspect for paint condition, warped surfaces, corrosion
or perforation. Sand and repaint as necessary.
• Replace fireplace if firebox has been perforated.
Control Compartment and Firebox Top
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, dust
cloths
• Vacuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
Figure 3.1 IPI Pilot Flame Pattern
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Installer Guide
Getting Started
4
A. Typical Appliance System
NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not
drawn to scale. Actual product may vary from pictures in manual
HORIZONTAL
TERMINATION CAP
(SECTION 7)
WALL PENETRATION
FRAMING
(SECTION 8B)
VERTICAL TERMINATION CAP
(SECTION 10)
NON-COMBUSTIBLE ROOF FLASHING
MAINTAINS MINIMUM CLEARANCE
AROUND PIPE
STORM COLLAR
(SECTION 10)
(SECTION 10)
VENT PIPE PENETRATES ROOF
PREFERABLY WITHOUT AFFECTING
ROOF RAFTERS (SECTION 8.C)
ATTIC INSULATION SHIELD (NOT SHOWN)
MUST BE USED HERE TO KEEP INSULA-
TION AWAY FROM VENT PIPE IF ATTIC IS
INSULATED. (SECTION 8.D)
VENT PIPE
(SECTIONS 7&8)
CEILING FIRESTOP ON
FLOOR OF ATTIC
(SECTION 8.C)
FRAMING HEADED
OFF IN CEILING
JOISTS (SECTION 8.C)
FRAMING/HEADER
(SECTION 5)
WALL SWITCH
GAS LINE
(SECTION 11)
Figure 4.1 Typical System
14
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Design and Installation Considerations
D. Inspect Appliance and Components
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.
• Carefully remove the appliance and components from
the packaging.
• The vent system components and decorative doors and
fronts may be shipped in separate packages.
Installation MUST comply with local, regional, state and
national codes and regulations. Consult insurance carrier,
local building inspector, fire officials or authorities having
jurisdiction over restrictions, installation inspection and
permits.
• If packaged separately, the log set and appliance grate
must be installed.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
• Read all of the instructions before starting the instal-
lation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
Before installing, determine the following:
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping.
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, in-
complete or substitute components. Keep appliance dry.
• Electrical wiring requirements.
• Framing and finishing details.
Hearth & Home Technologies disclaims any responsibility for,
and the warranty will be voided by, the following actions:
• Whether optional accessories—devices such as a wall
switch or remote control—are desired.
• Installation and use of any damaged appliance or vent
system component.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified
service technician, service agency or your dealer.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
C. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Any such action may cause a fire hazard.
Tape measure
Pliers
Framing material
WARNING! Risk of Fire, Explosion or Electric Shock!
DO NOT use this appliance if any part has been under
water. Call a qualified service technician to inspect the
appliance and to replace any part of the control system
and/or gas control which has been under water.
High temperature caulking material
Phillips screwdriver (magnetic)
Framing square
Hammer
Gloves
Voltmeter
Plumb line
Level
Electric drill and bits (1/4 in. magnetic)
Safety glasses
Reciprocating saw
Manometer
Flat blade screwdriver
Non-corrosive leak check solution
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
One 1/4 in. female connection (for optional fan).
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Framing and Clearances
5
It is important to follow the framing and finishing
instructions step by step to ensure proper placement of
fireplace in the surrounding framing/finishing materials.
A. Selecting Appliance Location
When selecting a location for the appliance it is important to
consider the required clearances to walls (see Figure 5.1).
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be locat-
ed out of traffic and away from furniture and draperies.
Unlike many traditional, single sided Heat & Glo fireplaces,
the SLR is recessed into surround framing. The left and
right nailing tabs were designed to ensure the fireplace is
recessed to the correct location within the framing materials.
Refer to Section 13 for detailed instructions on finishing.
NOTICE: Illustrations reflect typical installations and are
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due to
individual design preference.
A
E
1 IN.
D*
ALCOVE
INSTALLATION
A
B
C
TOP VENT
ONE 900 ELBOW
TOP VENT
ONE 90° ELBOW
B
F
A
B
48
C
75
D
E
F
Inches
Millimeters
53-1/32
1347
19-9/32
490
17-3/4
451
See Section D.
Figure 5.5 & 5.6
1218
1905
Figure 5.1 Appliance Locations
Î
16
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Constructing the Appliance Chase
C. Clearances
A chase is a vertical box-like structure built to enclose the
gas appliance and/or its vent system. In cooler climates
the vent should enclosed inside the chase.
NOTICE: Install appliance on hard metal or wood surfaces
extending full width and depth. DO NOT install directly
on carpeting, vinyl, tile or any combustible material other
than wood.
NOTICE: Treatment of ceiling firestops and wall shield
firestops and construction of the chase may vary with the
type of building. These instructions are not substitutes
for the requirements of local building codes. Therefore,
you MUST check local building codes to determine the
requirements to these steps.
WARNING! Risk of Fire! Maintain specified air space
clearances to appliance and vent pipe:
• Insulation and other materials must be secured to prevent
accidental contact.
• The chase must be properly blocked to prevent blown
insulation or other combustibles from entering and
making contact with fireplace or chimney.
Chases should be constructed in the manner of all out-
side walls of the home to prevent cold air drafting prob-
lems. The chase should not break the outside building
envelope in any manner.
• Failure to maintain airspace may cause overheating and
a fire.
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infiltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
Note: Figure 5.2 shows the fireplace installed on the
floor. However, this fireplace can be elevated off the floor
provided that the fireplace is properly supported by framing
materials and the ceiling clearances are maintained.
To further prevent drafts, the wall shield and ceiling fire-
stops should be caulked with high temperature caulk to
seal gaps. Gas line holes and other openings should be
caulked with high temp caulk or stuffed with unfaced in-
sulation. If the appliance is being installed on a cement
slab, a layer of plywood may be placed underneath to
prevent conducting cold up into the room.
MEASURE FROM TOP OF
FIREPLACE OPENING
A
E
F
B
H
J
C
G
D
I
MINIMUM FRAMING DIMENSIONS*
A
B
C
D
E
F
G
H
I
J
Rough
Opening
(Vent Pipe)
Rough
Opening
(Height)
Rough
Opening
(Depth)
Rough
Opening
(Width)
Clearance
to Ceiling
Combustible
Floor
Combustible
Flooring
Behind
Sides of
Front of
Appliance Appliance Appliance
8-5/8
219
42 1/4
1073
18-1/4
464
50
31
0
0
0
0
1
1
36
Inches
1270
787
25
25
914
Millimeters
Figure 5.2. Clearances to Combustibles
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Combustible Mantel Legs Or Wall Projections
Extending Past The Face Of The Fireplace
D. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clear-
ances to combustibles as specified. Framing or finishing
material closer than the minimums listed must be construct-
ed entirely of noncombustible materials (i.e., steel studs,
concrete board, etc).
Combustible Mantels
2 IN.
MINIMUM
1/2 in.
Thick Wall
3 FT. MAXIMUM
12 in.
MAX.
Sheathing
6 IN.
MINIMUM
Figure 5.5 Combustible Mantel Leg or Wall Projections
(Acceptable on both sides of opening)
14 in. MEASUREMENT FROM TOP OF
MIN. FIREPLACE OPENING
Non-combustible Mantel Legs Or Wall Projections
Extending Past The Face Of The Fireplace
Figure 5.3 Clearances To Combustible Mantels Or Other
Combustibles Above Appliance
Non-combustible Mantels
3 IN.
UNLIMITED
MINIMUM
1/2 in.
Thick Wall
Sheathing
12 in.
MAX.
Figure 5.6 Non-Combustible Mantel Leg or Wall Projections
(Acceptable on both sides of opening)
Î
Front Side Finishing Detail
MEASUREMENT
14 in.
MIN.
FROM TOP OF
FIREPLACE
OPENING
1.00 in.
FRAMING
Figure 5.4 Clearances To Non-Combustible Mantels Or Other
Non-Combustibles Above Appliance
1-9/16 in.
Note: For non-combustible fireplace finish mate-
rial (marble, stone, etc) specifications refer to Figure
13.13 and Figure 13.15.
1/2 in. BUILDING MATERIAL
Figure 5.7 Front Side Finishing Detail
18
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
1/2 in.
SHEETROCK
3-1/2 in.
NON-COMBUSTIBLE
BOARD SHIPPED
WITH APPLIANCE
1 in.
1-9/16 in.
AIR SPACE
Figure 5.8 Non-Combustible Zone
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Termination Locations
6
A. Vent Termination Minimum Clearances
DIRECT VENT GAS, WOOD OR FUEL
OIL TERMINATION
B
WARNING
C
Fire Risk.
Maintain vent clearance to combustibles as
A
specified.
• DO NOT pack air space with insulation or other
materials.
GAS
TERMINATION
Failure to keep insulation or other materials away
from vent pipe may cause overheating and fire.
HORIZONTAL
OVERHANG
Minimum Dimensions
Wood & Fuel Oil
Termination
Comments
Termination
2 FT.
20 INCHES MIN.
VERTICAL
MIN.
A
6 in.
20 in.
Horizontal distance between terminations
WALL
LOWEST
DISCHARGE
OPENING
B
C
20 in.
18 in.
24 in.
18 in.
Distance to perpendicular wall
Vertical distance between terminations
GAS DIRECT VENT
TERMINATION CAP
Figure 6.2 Staggered Termination Caps
X
12
DIRECT VENT GAS, WOOD OR FUEL
OIL TERMINATION
ROOF PITCH
IS X/ 12
20 IN.
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
(508 MM)
(MINIMUM) TO
PERPENDICULAR
WALL
20 IN. MIN. *
(508 MM)
WOOD OR
GAS TERMINATION
(GAS ONLY)
Roof Pitch
H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12.................................................1.25*
Over 7/12 to 8/12.................................................1.5*
Over 8/12 to 9/12.................................................2.0*
Over 9/12 to 10/12...............................................2.5
Over 10/12 to 11/12.............................................3.25
Over 11/12 to 12/12.............................................4.0
Over 12/12 to 14/12.............................................5.0
Over 14/12 to 16/12.............................................6.0
Over 16/12 to 18/12.............................................7.0
Over 18/12 to 20/12.............................................7.5
Over 20/12 to 21/12.............................................8.0
*
IF USING DECORATIVE CAP COVER(S), THIS DISTANCE MAY
NEED TO BE INCREASED. REFER TO THE INSTALLATION
INSTRUCTIONS SUPPLIED WITH THE DECORATIVE CAP COVER.
Figure 6.3 Leveled Termination Caps
* 3 foot minimum in snow regions
Figure 6.1 Minimum Height From Roof To Lowest Discharge
Opening
20
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
O
N
V
P
L
K
K
Electrical
Service
R
V
V
E
C
V
Q
A
F
C
(See Note 2)
V
Measure vertical clearances from this surface.
B
J
U.S
(3 FT.)
B
V
V
V
B
V
i
M
D
V
G
V
X
A
H OR i
Measure horizontal clearances from this surface.
= VENT TERMINAL
X
= AIR SUPPLY INLET
= AREA WHERE TERMINAL IS NOT PERMITTED
V
A
B
= 12 inches.................clearances above grade, veranda,
J** = 7 ft.......................... clearance above paved
(See Note 1)
(See Note 1)
porch, deck or balcony
sidewalk or a paved driveway
located on public property
= 12 inches.................clearances to window or door
that may be opened, or to perma-
K
L
=
6 inches.................clearance from sides of electri-
(See Note 5)
cal service
nently closed window. (Glass)
= 12 inches................clearance above electrical
C
= 18 inches.................vertical clearance to unventilated
soffit or to ventilated soffit located
above the terminal
(See Note 5)
service
Covered Alcove Applications
M*** = 18 inches .............clearance under veranda, porch,
deck, balcony or overhang
30 inches.................for vinyl clad soffits and below
electrical service
D
E
F
=
9 inches..................clearance to outside corner
42 inches ......... vinyl
= 6 inches...................clearance to inside corner
N
O
P
= 6 inches ........... non-vinyl sidewalls
12 inches ......... vinyl sidewalls
= 18 inches ......... non-vinyl soffit and overhang
42 inches ......... vinyl soffit and overhang
= 8 ft.
= 3 ft. (Canada)..........not to be installed above a gas
meter/regulator assembly within 3
feet (90 cm) horizontally from the
center-line of the regulator
G
H
= 3 ft...........................clearance to gas service regulator
vent outlet
= 9 inches (U.S.A.)
QMIN
3 feet
6 feet
9 feet
12 feet
RMAX
12 inches (Canada) clearance to non-mechanical
air supply inlet to building or the
combustion air inlet to any other
appliance
1 cap
2 caps
3 caps
4 caps
2 x Q ACTUAL
1 x Q ACTUAL
2/3 x Q ACTUAL
1/2 x Q ACTUAL
i
= 3 ft. (U.S.A.)
6 ft. (Canada)...........clearance to a mechanical (pow-
(See Note 1)
ered) air supply inlet
QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL
** a vent shall not terminate directly above a sidewalk or paved driveway
which is located between two single family dwellings and serves both
dwellings.
Note 3: Local codes or regulations may require different
clearances.
*** only permitted if veranda, porch, deck or balcony is fully open on a
Note 4: Termination caps may be hot. Consider their proximity to
doors or other traffic areas.
minimum of 2 sides beneath the floor, or meets Note 2.
Note 1: On private property where termination is less than 7 feet above a
sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap
shield is suggested. (See vents components page)
Note 5: Location of the vent termination must not interfere with
access to the electrical service.
In the U.S and Canada: Vent system termination is NOT permitted
in screened porches.
Note 2: Termination in a covered alcove space (spaces open only on one
side and with an overhang) are permitted with the dimensions specified
for vinyl or non-vinyl siding and soffits. 1. There must be 3 feet minimum
between termination caps. 2. All mechanical air intakes within 10 feet
of a termination cap must be a minimum of 3 feet below the termination
cap. 3. All gravity air intakes within 3 feet of a termination cap must be a
minimum of 1 foot below the termination cap.
Vent system termination is permitted in porch areas with two or more
sides open. You must follow all side walls, overhang and ground
clearances as stated in the instructions.
Heat & Glo assumes no responsibility for the improper performance
of the appliance when the venting system does not meet these
requirements.
Figure 6.4 Minimum Clearances for Termination
CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Vent Information and Diagrams
7
A. Approved Pipe
D. Measuring Standards
This appliance is approved for use with Hearth & Home
Technologies SLP venting systems. Refer to Section 16B
for vent component information.
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
• Pipe measurements are shown using the effective length
of pipe (see Figure 7.2).
DO NOT mix pipe, fittings or joining methods from differ-
ent manufacturers.
• Measurements are made from the appliance outer wrap,
not from the standoffs.
The pipe is tested to be run inside an enclosed wall.
There is no requirement for inspection openings at each
joint within the wall.
• Horizontal terminations are measured to the outside
mounting surface (flange of termination cap).
WARNING! Risk of Fire or Asphyxiation. This appli-
ance requires a separate vent. DO NOT vent to a pipe
serving a separate solid fuel burning appliance.
• Vertical terminations are measured to bottom of
termination cap.
• Horizontal pipe installed level with no rise.
NOTICE: TheSLP-HRC-SSandSLP-HRC-ZC-SStermination
caps are NOT approved for use with propane fuel.
A
B. Vent Table Key
The abbreviations listed in this vent table key are used in
the vent diagrams.
Symbol
Description
B
First section (closest to appliance) of vertical length
V1
Second section of vertical length
V2
H1
H2
First section (closest to appliance) of horizontal length
Subsequent sections of horizontal length
1-1/4 in. (32 mm)
OVERLAP
Figure 7.2 Chimney Offset/Return
C. Use of Elbows
Diagonal runs have both vertical and horizontal vent as-
pects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 7.1).
Effective Height/Length
Pipe
SLP4
inches
4
mm
102
152
305
610
914
1219
Two 45º elbows may be used in place of one 90º elbow.
On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216
mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A
length of straight pipe is allowed between two 45º elbows
(see Figure 7.1).
SLP6
6
Effective
Height/
Length
SLP12
SLP24
SLP36
SLP48
SLP6A
SLP12A
12
24
36
48
2 - 6 51 - 152
2 - 12 51 - 305
Figure 7.3 SLP Pipe Effective Length
Î
Vertical
E. Vent Diagrams
General Rules:
8-1/2 in.
• When penetrating a combustible wall, a wall shield
firestop must be installed.
• When penetrating a combustible ceiling, a ceiling firestop
must be installed.
Horizontal
• Horizontal runs of vent do not require vertical rise;
horizontal runs may be level.
Figure 7.1
22
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Fire Risk. Explosion Risk.
Do NOT pack insulation or other combustibles between ceiling firestops.
•
•
ALWAYS maintain specified clearances around venting and firestop systems.
Install wall shield and ceiling firestops as specified.
Failure to keep insulation or other material away from vent pipe may cause fire.
Top Vent - Horizontal Termination
Venting with 1 elbow
H1 Maximum
Note: Use SLP Series
components only.
V Minimum
SLR
90 Elbow
1-1/2 ft.
3 ft.
610 mm
914 mm
1.5 m
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 7.3).
1 ft.
305 mm
610 mm
914 mm
1.2 m
2 ft.
3 ft.
4 ft.
5 ft.
7 ft.
2.1 m
14 ft.
4.3 m
H MAX. =14 ft. (4.3 m)
V + H MAX. = 40 ft. (12.2 m)
Note: The SLP-HRC-SS and
SLP-HRC-ZC-SS
termination
caps are not approved for use
with propane (LP) fuel.
V1
H1
Figure 7.4
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
23
1. Top Vent - Horizontal Termination - (continued)
Top Vent - Horizontal Termination
Venting with 2 elbows
H1 + H2 MAXIMUM
SLR
Note: Use SLP Series
components only.
V Minimum
90° Elbow
1 ft.
305 mm
610 mm
1.2 m
1 ft.
2 ft.
3 ft.
4 ft.
305 mm
2 ft.
4 ft.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 7.3).
610 mm
914 mm
1.2 m
6 ft.
1.8 m
14 ft.
4.3 m
H + H1 MAX. =14 ft. (4.3 m)
V + H + H1 MAX. = 40 ft. (12.2 m)
Note: The SLP-HRC-SS and
SLP-HRC-ZC-SS
termination
caps are not approved for use
with propane (LP) fuel.
V1
H2
H1
INSTALLED
HORIZONTALLY
Figure 7.5
24
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Top Vent - Horizontal Termination - (continued)
Top Vent - Horizontal Termination
Venting with 3 elbows
SLR
Note: Use SLP Series
components only.
V1 Minimum
H1 + H2 Maximum
V2
*
V1 + V2 Minimum
90° Elbow
6 ft.
1.8 m
3.0 m
3.7 m
4.3 m
*
*
*
*
1 ft.
305 mm
610 mm
914 mm
10 ft.
12 ft.
14 ft.
*
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 7.3).
2 ft.
3 ft.
*
*
H1 + H2 MAX. =14 ft. (4.3 m)
V1 + V2 + H1 + H2 MAX. = 40 ft. (12.2 m)
*No specific restrictions on this value EXCEPT V1 + V2 + H cannot exceed 40 ft. (12.2 m)
Note: The SLP-HRC-SS and
SLP-HRC-ZC-SS
termination
caps are not approved for use
with propane (LP) fuel.
H2
V2
V1
H1
Figure 7.6
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
25
1. Top Vent - Horizontal Termination - (continued)
Top Vent - Horizontal Termination
Venting with 3 elbows
H1 + H2 + H3 MAXIMUM
SLR (NG ONLY)
Note: Use SLP Series
components only.
V Minimum
90° Elbow
ft.
mm
3 ft.
914 mm
15 ft.
4.6 m
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 7.3).
H1 + H2 + H3 MAX. =15 ft. (4.6 m)
Î
Note: This venting configuration
is approved ONLY for Natural
Gas models.
H2
H1
H3
V1
Figure 7.7
26
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Exhaust restrictor Instructions
Top Vent - Vertical Termination
No Elbows
1. Locate the two pilot holes located in the inside firebox
heat shield as shown in Figure 7.8.
2. Center the exhaust restrictor such that the thru holes
in the vent restrictor align with the pilot holes in the
restrictor.
V1 = 44 ft. Max. (13.4 m)
Note: If installing a vertical vent/termination off the top of the
appliance, the optional exhaust restrictor may be needed.
3. Use (2) ½” self-piercing screws to secure vent restric-
tor to firebox heat shield. See Figure 7.9
PILOT HOLES
Note: Use SLP Series
components only.
Figure 7.9 Location of Pilot Holes
V1
Figure 7.10 Exhaust Restrictor Installation
4. In some applications, such as those where the fire-
place is elevated off the floor, the vent restrictor may
be painted, but painting is not required.
Figure 7.8 Vertical Vent Maximum
Notice: Before painting, contact your dealer for information on
the appropriate high temperature paint.
Exhaust restrictors are recommended for these vertically
terminated products which have excessive draft. Exhaust
restrictors will compensate for high draft, and restore vi-
sual flame height. If the vent configuration has a total
vertical of 15-44 feet, an exhaust restrictor may be need-
ed. The exhaust restrictor can be located in the appliance
manual bag.
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Top Vent - Vertical Termination
Venting with 2 elbows
SLR
V1 Minimum
H Maximum
V2
*
V1 + V2 Minimum
90° Elbow
2 ft.
610 mm
914 mm
1.5 m
*
*
*
*
*
1 ft,
152 mm
457 mm
914 mm
1.1 m
3 ft.
5 ft.
*
2 ft.
3 ft.
4 ft.
*
7 ft.
2.1 m
*
Î
15 ft.
4.6 m
*
H MAX. =15 ft. (4.6 m)
V1 + V2 + H MAX. = 40 ft. (12.2 m)
* No specific restrictions on this value EXCEPT V1 + V2 + H cannot exceed 40 ft. (12.2 m)
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 7.3).
V2
V1
H1
Figure 7.11
28
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Top Vent - Vertical Termination
Venting with 3 elbows
SLR
V1 Minimum
H1 + H2 Maximum
V2
*
V1 + V2 Minimum
Î
90° Elbow
1 ft.
2 ft.
4 ft.
6 ft.
14 ft.
305 mm
610 mm
1.2 m
*
*
*
*
*
1 ft.
2 ft.
3 ft.
4 ft.
305 mm
*
610 mm
914 mm
1.2 m
*
1.8 m
*
4.3 m
*
H MAX. =14 ft. (4.3 m)
V1 + V2 + H1 + H2 MAX. = 40 ft. (12.2 m)
* No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 cannot exceed 40 ft. (12.2 m)
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
V2
(see Figure 7.3).
H1
H2
V1
INSTALLED
HORIZONTALLY
Figure 7.12
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Top Vent - Vertical Termination
Venting with 4 elbows
V1 MIN.
H1 MAX.
V2 MIN.
H2 MAX.
V3 MIN.
Note: Use SLP Series
1-1/2 ft. 457 mm 4 ft. 1.2 m 4 ft. 1.2 m 4 ft. 1.2 m 3-1/2 ft. 1.0 m
V1 + V2 + V3 + H1 + H2 Maximum= 40 ft. (12.2 m)
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
V3
V2
H2
H1
V1
Figure 7.13
30
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Vent Clearances and Framing
8
A. Pipe Clearances to Combustibles
B. Wall Penetration Framing
WARNING! Risk of Fire! Maintain air space clearance to
vent. DO NOT pack insulation or other combustibles:
Combustible Wall Penetration
Whenever a combustible wall is penetrated, you must
frame a hole for the wall shield firestop(s). The wall shield
firestop maintains minimum clearances and prevents cold
air infiltration.
• Between ceiling firestops
• Between wall shield firestops
• Around vent system
• The opening must be framed on all four sides using the
same size framing materials as those used in the wall
construction.
Failure to keep insulation or other material away from
vent pipe may cause over heating and fire.
• SLP pipe - A wall shield firestop must be placed on each
side of an interior wall. A minimum 1-1/2 in. (38 mm)
overlap of attached heat shields must be maintained.
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
• SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to
194 mm thick).
• If wall thickness is less than 4-3/8 the existing heat shields must be field trimmed.
If wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.
• See Section 10.L. for information for regarding the in-
stallation of a horizontal termination cap.
Î
Non-Combustible Wall Penetration
(SLP Pipe Shown)
If the hole being penetrated is surrounded by noncom-
bustible materials such as concrete, a hole with diameter
one in. greater than the pipe is acceptable.
Heat
Shield
3 in. (76 mm)
top clearance *
Heat
3 in. (76 mm)
top clearance
Whenever a non-combustible wall is penetrated, the wall
shield firestop is only required on one side and no heat
shield is necessary.
Shield
1 in. (25 mm)
clearance around
vertical sections
1 in. (25 mm)
clearance
bottom & sides
Wall
Shield
Firestop
DO NOT PACK WITH
INSULATION OR
OTHER MATERIAL
WALL
* When using SLP pipe, minimum clearances from the vent pipe to combustible materi-
als at inside wall firestops are:
Top: 2-1/2 in. (64 mm)
Bottom: 1/2 in. (13 mm)
Sides: 1 in. (25 mm)
10 in.
10 in.
B
Figure 8.1 Horizontal Venting Clearances To Combustible
Materials
A
A*
B
48-1/16 in. 47-1/16 in.
Î
* Shows center of vent framing hole for top venting. The
center of the hole is one (1) in. (25.4 mm) above the
center of the horizontal vent pipe.
Figure 8.2 Wall Penetration
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
31
C. Install the Ceiling Firestop
A ceiling firestop MUST be used between
floors and attics.
• SLP pipe only - Frame opening 9 in. x
9 in. (229 mm x 229 mm) whenever the
vent penetrates a ceiling/floor (see Figure
8.4).
ATTIC ABOVE
• Frame the area with the same sized lumber
as used in ceiling/floor joist.
• The ceiling firestop may be installed above or
below the ceiling joists when installed with a
attic insulation shield. It must be under joists
between floors that are not insulated. Refer
to Figure 8.5.
A
• Secure with three fasteners on each side.
WARNING! Risk of Fire! DO NOT pack insu-
lation around the vent. Insulation must be kept
back from the pipe to prevent overheating.
A
A
PIPE
SLP
9 in. (229 mm)
Figure 8.4 Installing Ceiling Firestop
INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
3 FASTENERS
PER SIDE
CEILING FIRESTOP
CEILING FIRESTOP
INSTALLED BELOW CEILING
INSTALLED ABOVE CEILING
Figure 8.5 Installing the Attic Shield
32
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Install Attic Insulation Shield
BEND ALL TABS INWARD 90°
TO MAINTAIN CLEARANCE
AND PREVENT INSULATION
FROM FALLING INSIDE
WARNING! Fire Risk. DO NOT allow loose materials or
insulation to touch vent. Hearth & Home Technologies
Inc. requires the use of an attic shield.
The National Fuel Gas Code ANSI Z223.1 and NFPA 54
requires an attic shield constructed of 26 gauge minimum
metal that extends at least 2 in. (51 mm) above insulation.
Attic shields must meet specified clearance and be se-
cured in place.
Flat Ceiling Installation
• Remove one shield from box.
LASER-ETCHED
CUT LINES
INSERT 3
SCREWS
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
BEND 3 TABS
OUTWARD TO
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
FASTEN TO CEILING
FIRESTOP-BEND
REMAINING TABS
INWARD 90 DEGREES
TO MAINTAIN
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
CLEARANCE
allow attachment to the ceiling firestop.
Figure 8.6 Attic Insulation Shield
• Bend the remaining bottom tabs inward 90° to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90° around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
Vaulted Ceiling Installation
• The attic insulation shield has been laser-etched with cut
lines and ceiling pitches to make field trimming easier.
• Remove one shield from box.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
• Cut the attic insulation shield (if application is for vaulted
ceiling) using a laser-etched cut line, to fit your ceiling
pitch. Snip cut edge to recreate 1 in. bend tabs all the
way around the bottom.
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
• Bend the remaining bottom tabs inward 90° to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90° around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Appliance Preparation
9
A. Top Vent
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
ELBOW HEAT SHIELD
SHOWN AS INSTALLED
ELBOW HEAT SHIELD SHOWN
IN SHIPPING POSITION
PIPE GASKET
Figure 9.2 Elbow Shield Shown Installed
Figure 9.1 Elbow Shield Shown as Shipped
If venting with a 90 degree elbow directly off of the top of
the appliance, the elbow heatshield must be repositioned
as shown in Figure 9.2.
If venting vertically or using a straight seciton of vertical
pipe, remove the elbow heat shield and discard by remov-
ing the two 1/4 in. screws that secure the elbow heat shield
to the top of the fireplace.
For all venting applications, ensure that the pipe gasket is
in place before attaching any pipe section. This gasket is
shipped in place around the starting collar. See Figure 9.2.
34
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Securing and Leveling the Appliance
WARNING! Risk of Fire! Prevent contact with:
• Sagging or loose insulation
• Insulation backing or plastic
• Framing and other combustible materials
Block openings into the chase to prevent entry of blown-
in insulation. Make sure insulation and other materials
are secured.
DO NOT notch the framing around the appliance
standoffs. Failure to maintain air space clearance may
cause overheating and fire.
NAILING TABS
BOTH SIDES
For details on setting the appliance in the framing, refer to
section 13.A. The diagram shows how to properly position,
level, and secure the appliance (see Figure 9.3). Nailing
tabs are provided to secure the appliance to the framing
members.
• Bend out nailing tabs on each side.
• Place the appliance into position.
• Keep nailing tabs flush with the framing.
• Level the appliance from side to side and front to back.
Figure 9.3 Proper Positioning, Leveling And Securing Of An
Appliance
• Shim the appliance as necessary. It is acceptable to use
wood shims underneath the appliance.
• Secure the appliance to the framing by using nails or
screws through the nailing tabs.
• Secure the appliance to the floor by inserting two screws
through the pilot holes at the bottom of the appliance.
Figure 9.3 shows the fireplace installed on the floor.
However, this fireplace can be elevated off the floor
provided that the fireplace is properly supported by framing
materials and the ceiling clearances are maintained.
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Installing Vent Pipe (SLP Pipe)
10
A. Assemble Vent Sections
To attach the first vent component to the starting collars
of the appliance:
• Lock the vent components into place by sliding the pipe
section onto the collar.
• Align the seam of the pipe and seam of collar to allow
engagement. Rotate the vent component to lock into
place. Use this procedure for all vent components. See
Figure 10.1.
Note: Align seams to engage pipe,
then rotate counterclockwise to lock
• Slide the gasket over the first vent section and place it
flush to the appliance. This will prevent cold air infiltration.
High temperature caulk may be used to hold the part in
place.
Figure 10.1 Adding Venting Components
• Continue adding vent components, locking each
succeeding component into place.
• Ensure that each succeeding vent component is securely
fitted and locked into the preceding component.
Commercial, Multi-family (Multi-level exceeding two sto-
ries), or High-Rise Applications
For Installation into a commercial, multi-family (multi-level
exceeding two stories) or high-rise applications: All outer
pipe joints must be sealed with high temperature silicone,
including the slip section that connects directly to the hori-
zontal termination cap.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 10.2
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
Figure 10.2 High Temperature Silicone Sealant
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing
termination cap from slip pipe. If slip section seals are
broken during removal of the termination cap, vent may
leak.
36
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Assemble Slip Sections
C. Secure The Vent Sections
• Vertical runs of pipe must be supported every 8 ft. (2.44 m).
• Slide the inner flue of the slip section into the inner flue of
the pipe section and the outer flue of the slip section over
the outer flue of the pipe section. See Figure 10.3.
• Horizontal sections must be supported every 5 feet
(1.52 m).
• Vent supports or plumbers strap (spaced 120º apart) may
• Slide together to the desired length.
be used to support. See figures 10.5 and 10.6.
• Wall shield firestops may be used to provide horizontal
support.
• Ceiling firestops have tabs that may be used to provide
vertical support.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Improper support may allow vent to sag and separate.
Use vent run supports and connect vent sections per in-
stallation instructions. DO NOT allow vent to sag below
connection point to appliance.
Pilot hole
Figure 10.3 Slip Section Pilot Holes
• Maintain a 1-1/2 in. (38 mm) overlap between the slip
section and the pipe section.
• Secure the pipe and slip section with two screws no
longer than 1/2 in. (13 mm), using the pilot holes in the
slip section. See Figure 10.4.
Î
Figure 10.5 Securing Vertical Pipe Sections
Figure 10.6 Securing Horizontal Pipe Sections
Î
Figure 10.4 Screws into Slip Section
• Continue adding pipe as necessary following instructions
in “Assembling Pipe Sections.”
NOTICE: If slip section is too long, the inner and outer flues
of the slip section can be cut to the desired length.
NOTICE: When installing a vent system with an HRC
termination cap, all pipe system joints shall be sealed using
a high temperature silicone sealant.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections.
• Only outer pipes are sealed, sealing the inner flue is not
required.
• All unit collar, pipe, slip section, elbow and cap outer flues
shall be sealed.
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
37
D. Disassemble Vent Sections
• Level the support box both vertically and horizontally and
temporarily tack it in place through the inside walls into
the roof sheathing.
• Rotate either section (see Figure 8.7) so the seams on
both pipe sections are aligned as shown in Figure 10.8.
• Use tin snips to cut the support box from the top corners
down to the roof line and fold the resulting flaps to the
roof. See Figure 10.10.
• Pull carefully to separate the pieces of pipe.
• Nail the flaps to the roof AFTER running a bead of non
hardening sealant between the flaps and the roof.
WARNING! Risk of Fire! Clean out ALL materials from
inside the support box and complete the vertical vent run
and termination.
LEVEL
CATHEDRAL CEILING
SUPPORT BOX
Figure 10.7 Rotate Seams for Disassembly
2 in. (51 mm) MIN. BELOW
FINISHED CEILING
CUT HOLE 1/8 in. (3 mm)
GREATER IN SIZE THAN
PATTERN OF SUPPORT
BOX AS IT IS PROJECTED
ONTO ROOF LINE
Figure 10.9
Figure 10.8 Align and Disassemble Vent Sections
E. Install Decorative Ceiling Components
A decorative ceiling thimble can be installed on a flat ceil-
ing through which the vent passes. The decorative ceiling
thimble is used to cover the firestop.
• Seal the gap between the vent pipe and firestop using
high temperature silicone to prevent cold air infiltration.
• Install the decorative ceiling thimble by sliding it up to
the ceiling and attaching it using the provided screws.
Adecorative cathedral ceiling support box can be installed
on a cathedral ceiling through which the vent passes.
• Use a plumb-bob to mark the center line of the venting
system on the ceiling and drill a small hole through the
ceiling and roof at this point. Locate the hole and mark
the outline of the cathedral ceiling support box on the
outside roof.
Figure 10.10
• Remove shingles or other roof covering as necessary to
cut the rectangular hole for the support box. Cut the hole
1/8 in. (3 mm) larger than the support box outline.
• Lower the support box through the hole in the roof until its
bottom is at least 2 in. (51 mm) below the ceiling (Figure
10.9).
38
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
F. Install Metal Roof Flashing
Note: Skip this section if using the RF4-8.
• See minimum vent heights for various pitched roofs
(Figure 10.11) to determine the length of pipe to extend
through the roof.
CAULK
• Slide the roof flashing over the pipe sections extending
through the roof as shown in Figure 10.12.
HORIZONTAL
OVERHANG
2 FT.
20 INCHES MIN.
VERTICAL
MIN.
WALL
Figure 10.12
LOWEST
DISCHARGE
OPENING
G. Assemble and Install Storm Collar
GAS DIRECT VENT
TERMINATION CAP
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
X
lation. Sheet metal edges are sharp.
12
• Connect both halves of the storm collar with two screws
(see Figure 10.13).
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
• Wrap the storm collar around the exposed pipe section
closest to the roof and align brackets. Insert a bolt
(provided) through the brackets and tighten the nut to
complete the storm collar assembly. Make sure the collar
is tight against the pipe section.
• Slide the assembled storm collar down the pipe section
Roof Pitch
H (Min.) Ft.
until it rests on the roof flashing (see Figure 10.14).
Flat to 6/12........................................1.0*
Over 6/12 to 7/12............................1.25*
Over 7/12 to 8/12..............................1.5*
Over 8/12 to 9/12..............................2.0*
Over 9/12 to 10/12............................. 2.5
Over 10/12 to 11/12......................... 3.25
Over 11/12 to 12/12........................... 4.0
Over 12/12 to 14/12........................... 5.0
Over 14/12 to 16/12........................... 6.0
Over 16/12 to 18/12........................... 7.0
Over 18/12 to 20/12........................... 7.5
Over 20/12 to 21/12........................... 8.0
• Caulk around the top of the storm collar (see Figure 10.20).
* 3 foot minimum in snow regions
Figure 10.11 Minimum Height From Roof To Lowest Discharge
Opening
Figure 10.13 Assembbling the Storm Collar
NOTICE: Failure to properly caulk the roof flashing could
cause water entry.
• Caulk the gap between the roof flashing and the outside
diameter of the pipe.
• Caulk the perimeter of the flashing where it contacts the
roof surface. See Figure 10.12.
Figure 10.14 Assembling the Storm Collar Around the Pipe
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
39
H. Install RF4-8
The RF4-8 may be used in place of the roof flashing and
Î
storm collar (Sections 10.F and Section 10.G.)
Pipe must be supported within 12 inches of the roofline
using plumbers strapping or an SLP-FS when using the
RF4-8 Flashing. Refer to Sect. 10.C Securing Vent Sec-
tions.
SECURE WITH 4
SCREWS NO LONGER
THAN 1 IN. (25 MM)
Figure 10.17 Apply Sealant
SLP-FS
Figure 10.15 Secure Pipe with SLP-FS
• Trim the rubber boot (using scissors or a utility knife),
cutting along the marked measurement lines. See Figure
10.16. Use the 150 mm line.
• Lubricate pipe or flue with water and slide the flashing
down. It may be necessary to trim the top shingles around
the base of the rubber boot to ensure a good fit.
APPLY SEALANT
TOP & PARTIAL SIDES
• Draw around flashing, remove.
• Apply silicone sealant to roof inside the lines (Figure 10.17)
• Lubricate pipe or flue with water and slide flashing down.
Seat firmly in sealant. Nail roof flashing to the roof.
Figure 10.18 Slide Flashing Down, Secure & Apply Sealant
• Apply silicone sealant on the top outside of the base plate
on the sides and on top edge. See Figure 10.18. Install
shingles, Apply sealant at the top edge of the rubber
boot. See Figure 10.19.
SILICONE SEALANT
(TOP OF BOOT)
• We recommend that you top coat with conventional
acrylic house paint to improve the appearance of your
galvanized base flashing.
SHINGLES TRIMMED
FLASHING OVER
SHINGLES OVER
SHINGLES
FLASHING
Figure 10.19 Installation Complete
Figure 10.16 Trim Rubber Boot
40
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
K. Heat Shield Requirements for Horizontal
Termination
I. Install Vertical Termination Cap
• Attach the vertical termination cap by sliding the inner
collar of the cap into the inner flue of the pipe section
while placing the outer collar of the cap over the outer
flue of the pipe section.
WARNING! Risk of Fire! To prevent overheating and fire,
heat shields must extend through the entire wall thick-
ness.
• Secure the cap by driving three self-tapping screws
(supplied) through the pilot holes in the outer collar of the
cap into the outer flue of the pipe (see Figure 10.20).
• DO NOT remove the heat shields attached to the
wall shield firestop and the horizontal termination cap
(shown in Figure 10.22).
• Heat shields must overlap 1-1/2 in. (38 mm) mini-
mum.
TERMINATION CAP
There are two sections of the heat shield. One section
is factory-attached to the wall shield firestop. The other
section is factory-attached to the cap. See Figure 10.22.
If the wall thickness does not allow the required 1-1/2 in.
(38 mm) heat shield overlap when installed, an extended
heat shield must be used.
• If the wall thickness is less than 4 in./102 mm (DVP)
or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap
and wall shield firestop must to be trimmed. A minimum
1-1/2 in. (38 mm) overlap MUST be maintained.
(1 of 3)
• Useanextendedheatshieldifthefinishedwallthickness
is greater than 7-1/4 in. (184 mm).
STORM
COLLAR
• The extended heat shield may need to be cut to length
maintaining sufficient length for a 1-1/2 in. (38 mm)
overlap between heat shields.
SCREWS
CAULK
• Attach the extended heat shield to either of the existing
heatshieldsusingthescrewssuppliedwiththeextended
heat shield. Refer to vent components diagrams in the
back of this manual.
• Rest the small leg on the extended heat shield on top
of the pipe section to properly space it from the pipe
section.
Figure 10.20
J. Install Decorative Wall Components
Important Notice: Heat shields may not be field constructed.
A decorative wall thimble can be installed on wall through
which the vent passes. The decorative wall thimble is used
to cover the firestop.
• Slide the decorative wall thimble over the last section of
horizontal pipe before connecting the termination cap to
the pipe.
• Once the pipe section and the termination cap have been
connected, slide the wall thimble up to the interior wall
surface and attach with screws provided. See Figure
10.21.
Figure 10.21 Wall Thimble
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
41
L. Install Horizontal Termination Cap
WARNING! Risk of Fire! The telescoping flue section
of the termination cap MUST be used when connecting
vent.
• 1-1/2 (38 MM) MINIMUM OVERLAP OF FLUE TELE-
SCOPING SECTION IS REQUIRED.
FAILURE TO MAINTAIN OVERLAP MAY CAUSE OVER-
HEATING AND FIRE.
• Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
• Flash and seal as appropriate for siding material at
outside edges of cap.
• When installing a horizontal termination cap, follow
the cap location guidelines as prescribed by current
ANSI Z223.1 and CAN/CGA-B149 installation codes
and refer to Section 6 of this manual.
CAUTION! Risk of Burns! Local codes may require in-
stallation of a cap shield to prevent anything or anyone
from touching the hot cap.
NOTICE: For certain exposures which require superior
resistance to wind-driven rain penetration, a flashing kit and
HRC caps are available. When penetrating a brick wall, a
brick extension kit is available for framing the brick.
Note: When using termination caps with factory-supplied heat
shield attached, no additional wall shield firestop is required on
the exterior side of a combustible wall.
HEAT SHIELD OR
HEAT SHIELD
EXTENDED
HEAT SHIELD
1-1/2 IN. (38 MM) MIN.
OVERLAP
WALL SHIELD
FIRESTOP
SLIP SECTION
CAN BE EXTENDED
INNER VENT
SHEATHING
OUTER VENT
INTERIOR
EXTERIOR
Figure 10.22 Venting through the wall
42
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas Information
11
A. Fuel Conversion
SCREW LOCATIONS (16)
• Make sure the appliance is compatible with available gas
types.
DO NOT REMOVE
THESE FOUR SCREWS
• Conversions must be made by a qualified service
technician using Hearth & Home Technologies specified
and approved parts.
B. Gas Pressure
• Optimum appliance performance requires proper input
pressures.
• Gas line sizing requirements will be determined in ANSI
Z221.3 National Fuel Gas Code in the USA and CAN/
CGA B149 in Canada.
• Pressure requirements are:
Figure 11.1 Basepan Removal
Î
Gas Pressure
Minimum inlet pressure
Maximum inlet pressure
Manifold pressure
Natural Gas
5.0 in. w.c.
14.0 in. w.c.
3.5 in. w.c.
Propane
11.0 in. w.c.
14.0 in. w.c.
10.0 in. w.c.
WARNING! Risk of Fire or Explosion! High pressure
will damage valve. Low pressure may cause explosion.
• Verify inlet pressures. Verify minimum pressures when
other household gas appliances are operating.
• Install regulator upstream of valve if line pressure is
greater than 1/2 psig.
WARNING
Fire Risk.
ACCESS TO
MANUAL SHUTOFF
VALVE AND
Explosion Hazard.
High pressure will damage valve.
JUNCTION BOX
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
LOWER COVER
PANEL
VALVE
ASSEMBLY
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
Figure 11.2 Gas and Electrical Access
Note: This appliance does include a manual gas shutoff
valve that is located in the valve compartment. This manual
gas shutoff valve is accessible for service by removing the
basepan and burner assembly. See Figure 11.1.
Note: Have the gas supply line installed in accordance with
local codes, if any. If not, follow ANSI 223.1. Installation
should be done by a qualified installer approved and/or
licensed as required by the locality. (In the Commonwealth
of Massachusetts installation must be performed by a
licensed plumber or gas fitter).
The lower access cover panel is removable if finishing
material is not installed.
There is an access plate located on the left side of the
firebox bottom. See Figure 11.2. Remove screws and
plate to access the manual shutoff valve included with this
fireplace. See Figure 11.3 and Figure 11.4. Depending upon
local code, an additional manual gas shutoff, in an easily
accessible area may be required and located upstream from
the appliance.
Note: A listed (and Commonwealth of Massachusetts ap-
proved) 1/2 in. (13 mm) T-handle manual shut-off valve
and flexible gas connector are connected to the 1/2 in. (13
mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
43
C. Gas Connection
• Refer to Reference Section 16 for location of gas line
access in appliance.
• Gas line may be run through knockout(s) provided.
• The gap between supply piping and gas access hole
may be caulked with high temperature caulk or stuffed
with non-combustible, unfaced insulation to prevent cold
air infiltration.
• Ensure that gas line does not come in contact with outer
wrap of the appliance. Follow local codes.
• Pipe incoming gas line into valve compartment.
• Connect incoming gas line to the 1/2 in. (13 mm)
connection on manual shutoff valve.
WARNING! Risk of Fire or Explosion! Support control
when attaching pipe to prevent bending gas line.
Figure 11.3 Gas Fitting Access
• A small amount of air will be in the gas supply lines.
WARNING! Risk of Fire or Explosion! Gas build-up dur-
ing line purge could ignite.
• Purge should be performed by qualified service
technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks
or open flames.
Light the appliance. It will take a short time for air to purge
from lines. When purging is complete the appliance will
light and operate normally.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Check all fittings and connections with a non-corrosive
commercially available leak-check solution. DO NOT use
open flame. Fittings and connections could have loos-
ened during shipping and handling.
WARNING! Risk of Fire! DO NOT change valve settings.
This valve has been preset at the factory.
Figure 11.4 Gas Fitting and Junction Box Access
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce burner orifice 4% for each 1000 feet
above 2000 feet.
• In CANADA: Reduce burner orifice 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
44
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Information
12
A. Wiring Requirements
C. Optional Accessories Requirements
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
Wiring for optional Hearth & Home Technologies approved
accessories should be done now to avoid reconstruction.
Follow instructions that come with those accessories.
• Wire the appliance junction box to 110-120 VAC. This is
required for use of optional accessories (standing pilot
ignition) or proper operation of the appliance (Intellifire
ignition).
Optional Remote Control Receiver and Battery Pack
Location
Î
Batteries are to be installed only when battery power is
required. Because of the limited accessibility to valve
cavity, the position of the Battery Tray, IPI Control Module,
and Optional Remote Control Receiver locations must be
installed as shown in Figure 12.1.
• Low voltage and 110 VAC voltage cannot be shared
within the same wall box.
WARNING! Risk of Shock or Explosion! DO NOT wire
110V to the valve or to the appliance wall switch. Incorrect
wiring will damage controls.
The Battery Tray, Control Module, and Remote Control
receiver can be accessed thru the air space between the
firebox front and the lower-front finishing cover panel. The
decorative front and glass assembly must be removed to
access these components.
B. Intellifire Ignition System Wiring
• Wire the appliance junction box to 110 VAC for proper
operation of the appliance.
WARNING! Risk of Shock or Explosion! DO NOT wire
IPI controlled appliance junction box to a switched circuit.
Incorrect wiring will override IPI safety lockout.
The battery tray is attached with velcro to the inside of
the lower cover panel. The IPI control module and the
remote control receiver are placed on the firebox bottom.
• Refer to Figure 12.2, Intellifire Pilot Ignition (IPI) Wiring
Diagram.
• This appliance is equipped with an Intellifire control valve
which operates on a 3 volt system.
• Plug the 3-volt AC transformer into the appliance junction
box to supply power to the unit OR install two D cell
batteries (not included) into the battery pack before use.
NOTICE: Batteries should not be placed in the battery
pack while using the transformer. Remove batteries before
using the transformer, and unplug the transformer before
installing the batteries. Battery polarity must be correct or
module damage will occur.
FIREBOX BOTTOM
BATTERY TRAY
IPI CONTROL MODULE
REMOTE CONTROL RECEIVER
LOWER ACCESS PANEL
Figure 12.1 Valve Cavity
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
45
IGNITION MODULE 3 VAC
I
INTERMITTENT PILOT IGNITOR
S
TRANSFORMER
3 VAC
WHITE
ORANGE
GROUND TO
FIREPLACE
CHASSIS
PLUG IN
WIRES
(TO BROWN)
BATTERY PACK
THERMOSTAT
WIRE ASSEMBLY
NOTE: 1. Ignition module, valve, pilot, and
wall switch operate on 3 volts. 120 VAC is
required at junction box unless equipped
with battery back-up.
VALVE
Figure 12.2 Intellifire Pilot Ignition (IPI) Wiring Diagram with Wall Switch or Thermostat
D. Electrical Service and Repair
NOTE: There is an alternative access to the junction box.
This can be accessed by removing the valve assembly.
See Figure 11.2.
Î
WARNING! Risk of Shock! Label all wires prior to dis-
connection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper
operation after servicing.
WARNING! Risk of Shock! Replace damaged wire with
type 105° C rated wire. Wire must have high temperature
insulation.
E. Junction Box Installation
1. Remove the two screws that hold the junction box
JUNCTION BOX
BRACKET
bracket to the right corner of the fireplace.
2. Remove the one screw that secures the junction box
to the junction box bracket.
3. Route the wire through the strain relief in the outer
wrap and down through the strain relief on left side of
the junction box bracket and up through the right strain
relief. See Figure 12.3.
NOTICE: DO NOT wire
110 VAC to wall switch.
Figure 12.3 Junction Box Detail
4. Make the connection inside the junction box to the 120V
wire. Connect green to the ground nut, black to black
and white to white.
In the event that the junction box needs to be accessed
or installed after finish methods have been applied, ac-
cess is possible by removing the valve assembly. See
Fig. 11.2. Bend the top heat shield back and remove the
one screw that secures the junction box to the bracket.
Ensure the heat shield is bent back so that it is positioned
above the junction box.
Î
5. Reattach junction box to junction box bracket with one
screw.
6. Reattach the junction box bracket to the appliance with
two screws.
46
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Finishing
13
Setting the Fireplace into the Framing
A. Framing and Finishing Instructions
Unlikemanytraditional,single-sidedHeat&Glofireplaces,
this fireplace is recessed into surround framing. The left
and right nailing tabs were designed for the SLR model
as a means to ensure the fireplace is recessed to the
correct location within the framing materials.
WARNING! Risk of Fire! Comply with all minimum clear-
ances to combustibles as specified. Framing closer than the
minimums listed must be constructed entirely of noncom-
bustible materials (i.e., steel studs, concrete board, etc.)
Failure to comply could cause fire.
1. Bend three nailing tabs away from fireplace 180
degrees on both left and right nailing tabs. Do not
adjust the column standoffs. See Figure 13.1 and
Figure 13.2.
Finishing Instructions
It is important to follow the framing and finishing
instructions to ensure proper placement of fireplace into
the surrounding framing/finishing materials.
2. Screw each nailing tab to the adjoining framing
material. Ensure that the 1” air space clearance is
maintained on the sides of the fireplace. See Figure
13.3.
Wall sheathing materials 1/2 in. thick are specified in
this installation manual to properly align with the factory-
installed non combustible material
Top Flange
Factory-Installed
Top Flange
Factory-Installed
Non-Combustible
Board
Non-Combustible
Board
WARNING! Risk of Fire!
DO NOT, under any
circumstances, remove the factory-installed non-
combustible board or cover it with any combustible
material, such as:
NAILING TABS
•
•
•
Drywall (gypsum board)
Plywood
DO NOT ADJUST
Or other materials that do not meet the ASTM E
136 Non-combustibility standard. See specification
below
Failure to comply with these instructions may cause a
fire or cause the appliance to overheat.
Non-Combustible Materials Specification
Figure 13.1 Nailing Tabs
Shipping Position
Figure 13.2 Nailing Tabs
Installation Position
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750 ºC and UL763 shall be
considered non-combustible materials.
1.00 in.
FRAMING
1-9/16 in.
1/2 in. BUILDING MATERIAL
Figure 13.3 Front Side Finishing Detail
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
47
When finishing the wall around the fireplace, it is critical
that wall sheathing be fastened properly. Wall sheathing
fasteners, such as screws or nails, are not permitted in
some locations. See Figure 13.4. It is acceptable to
pre-drill holes and use self-tapped screws in the factory-
installed non-combustible board which may be used
to lathe (a backer for tile, marble, etc.) Screws being
installed through the factory-installed non-combustible
board should be self-tapping type with a minimum length
of 5” and maximum length of 7”. It is also acceptable
to penetrate the top flange with self-tapping screws.
See Figure 13.4. Do not drill or install screws into the
side columns as the existing stand-offs will support
the wall sheathing. Do not drill or install screws which
may penetrate the lower cover panel as this will restrict
required access to the glass, battery-back-up, and remote
receiver. See Figure 13.4.
WARNING! Risk of Fire! Maintain specified air space
clearances to combustibles.
Failure to comply with these instructions may cause a
fire or cause the appliance to overheat.
Ensure that the one inch back clearance and one inch
side clearances are maintained.
TOP FLANGE
NON-COMBUSTIBLE BOARD
(PROVIDED WITH UNIT)
The appliance is designed to accept ½” wall sheathing
materials such as drywall, plywood, wood composites,
or non-combustible materials. The type of material used
depends whether the installation is an Inside or Overlap
Fit method. Reference Section 13.C regarding installation
details associated with the Inside an Overlap Fit methods.
The left/right sides and bottom of the fireplace opening
include finishing flanges that will interlock with ½” wall
sheathing. See Figure 13.4. The ½” thick wall sheathing
can be installed tight to the left, right, and bottom finishing
flanges such that the rough edges of the sheathing
are tucked behind the flanges. See Figure 13.5. It is
necessary to cut a ½” slot in the sheathing where it is
tucked tightly behind the lower finishing flange. See
Figure 13.7.
FINISHING FLANGES
LOWER COVER PANEL
NO
SCREWS
SIDE COLUMNS
Figure 13.4 Finishing Details
CAUTION! RISK OF GLASS DAMAGE AND CUTS! DO
NOT DRILL OR INSTALL ANY TYPE OF SCREW OR
FASTENERINTOTHELOWERCOVERPANEL. SHARP
SCREW OR FASTENER TIPS MAY PENETRATE AND
BREAK THE GLASS OR CAUSE CUTS.
Verify that the lover cover panel is installed correctly, and
that the fireplace opening height is 16 in. See Figure 13.6.
NOTE: It is acceptable to use a high temperature sili-
cone sealant to adhere drywall to lower cover panel.
The SLR can be finished using either the Tonic or
Martini decorative fronts. See Figures 13.17 and 13.18.
Depending on the decorative front, the final fireplace
installation can be accomplished by either the “overlap”
or “inside-fit” method. Reference Section 13.C regarding
installation details associated with the Inside and Overlap
Fit methods.
FINISHING
FLANGES
If the final fireplace installation uses the Overlap Method,
wall sheathing material ½” thick is specified and can
be installed tight to the side finishing flanges. If the
final fireplace installation uses the Inside-Fit Method,
additional clearance of 4” must be maintained between
combustible ½” thick wall sheathing material and the
side finishing flanges. Reference Section 13.C regarding
installation details associated with the Inside and Overlap
Fit methods.
Figure 13.5 Side Wall Sheathing Installed
Î
48
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
16 IN.
Figure 13.6 Confirm Fireplace Opening
Dimension
SIDE WALL
SHEATHING
1/2 INCH CUT IN
WALL SHEATHING
LOWER WALL
SHEATHING
Figure 13.7 Lower Drywall Detail
Sealing Joints
The joints between the drywall sides and drywall
above the top factory installed non-combustible board
CAN NOT be sealed with a combustible drywall tape.
Depending upon the final finishing method, use a
minimum rated 300 degree sealant, drywall compound,
or thin set to seal the side and top joints.
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Combustible Mantel Legs Or Wall Projections
Extending Past The Face Of The Fireplace
B. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clear-
ances to combustibles as specified. Framing closer than the
minimums listed must be constructed entirely of noncom-
bustible materials (i.e., steel studs, concrete board, etc.)
Failure to comply could cause fire.
Note: For non-combustible fireplace finish mate-
rial (marble, stone, etc) specifications refer to Figure
13.13 and Figure 13.15.
2 IN.
MINIMUM
3 FT. MAXIMUM
Combustible Mantels
6 IN.
MINIMUM
Figure 13.10 Combustible Mantel Leg or Wall Projections
(Acceptable on both sides of opening)
1/2 in.
Thick Wall
12 in.
MAX.
Sheathing
Non-combustible Mantel Legs Or Wall Projections
Extending Past The Face Of The Fireplace
14 in. MEASUREMENT FROM TOP OF
MIN. FIREPLACE OPENING
3 IN.
Figure 13.8 Clearances To Combustibles Mantels Or Other
Combustibles Above Appliance
UNLIMITED
MINIMUM
Non-combustible Mantels
Figure 13.11 Non-Combustible Mantel Leg or Wall Projections
(Acceptable on both sides of opening)
Î
1/2 in.
Thick Wall
Sheathing
12 in.
MAX.
MEASUREMENT
14 in.
MIN.
FROM TOP OF
FIREPLACE
OPENING
Figure 13.9 Clearances To Non-Combustible Mantels Or Other
Non-Combustibles Above Appliance
50
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Both the Tonic and Martini decorative fronts can be in-
stalled such that they overlap non-combustible materials
up to 1 in. thick. See Figure 13.12 and Figure 13.13.
C. Facing Material
• Facing and/or finishing materials must not interfere with
air flow through louvers, operation of louvers or doors,
or access for service.
Additionally, the Tonic is approved to be installed in an
inside fit application with up to 4 in. of non-combustible
material up to 4 in. thick. See Figure 13.14, Figure 13.15
and Figure 13.16.
• Facing and/or finishing materials must never overhang
into the glass opening.
• Observe all clearances when applying combustible
materials.
Please refer to the appropriate section for specific require-
ments for each method if installation. See Figure 13.17
and Figure 13.18 for decorative front identification.
WARNING! Risk of Fire! DO NOT apply combustible
materials beyond the minimum clearances. Comply with
all minimum clearances to combustibles as specified in
this manual. Overlapping materials could ignite and will
interfere with proper operation of doors and louvers.
Non-Combustible Finish Materials
0 - 1 inch thickness-Overlap Fit Method
Both the Tonic and Martini decorative fronts are designed
to overlap finish materials 0 inches to 1 inch thick. See
Figure 13.12.
WARNING! Risk of Fire! DO NOT install drywall or other
combustible materials over the factory-installed non-com-
bustible board. Overlapping materials could ignite.
NOTICE: This one inch maximum not only includes the
decorative finish materials (marble, tile, slate, etc) but also
the thinset, lath and adhesive used to attach the decorative
finish material.
Decorative facing material thickness is measured from
the face of the factory-installed non-combustible board.
See Figure 13.12 and Figure 13.14.
The non-combustible finish material can be installed up to
the 16 inch (height) by 43 inch (width) fireplace opening.
FACTORY-INSTALLED
NON-COMBUSTIBLE
BOARD
NON-COMBUSTIBLE
FINISHING MATERIAL
0-1 IN. THICK
Top Joint
0 in.
Side
Joint
Side
Joint
NON-COMBUSTIBLE
BOARD
TONIC DECORATIVE
FRONT SHOWN
Bottom
Joint
Figure 13.13 Non-Combustible Finish Material Diagram for 0-1
Inch Thick Overlap Fit Method (Tonic or Martini
Decorative Front)
NON-COMBUSTIBLE
FINISHING MATERIAL
0-1 IN. THICK
DRYWALL OR
EQUIVALENT
(1/2 IN.)
Figure 13.12 Overlap Fit Method (Tonic or Martini Decorative
Front)
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Non-Combustible Finish Materials
0 Inches to 4 Inches Thick Inside Fit Method
Top Joint
Note: The Inside Fit application is only approved for the
0 in.
Non-Combustible
Finishing Material
4 in. MINIMUM
Tonic decorative front.
Side
Joint
The Tonic decorative front is approved for inside fit ap-
plications. Non-combustible finishing materials up to 4
inches thick can be installed around the Tonic front (left,
right, top, and bottom). The inside fit method requires an
additional 4 in. of 1/2 in. thick non-combustible building
material (not supplied with fireplace) to be installed on
the left and right sides flush with the factory installed non-
combustible board. See Figure 13.15.
NON-COMBUSTIBLE
BOARD
Non-Combustible
Finishing Material
4 in. MINIMUM
0 in.
0 in.
Bottom
Joint
WARNING! Risk of Fire! The Martini decorative Front
is not approved for inside fit installations. DO NOT install
Martini decorative front using an inside fit application.
Resulting elevated \temperatures may cause overheating
and fire.
Figure 13.15 Noncombustible Surface Finishing Material 0-4
Inches Thick-Inside Fit Method (Tonic Decorative
Front Only)
For the Tonic decorative front inside fit applications, the
decorative front must be installed tightly to the finishing
flanges and must not overlap any finish material.
Ensure that no non-combustible finish materials are in-
stalled within 3/4 in. of the fireplace opening. The 3/4 in.
spacing is required to provide clearance for removing and
installing the Tonic decorative front. See Figure 13.16.
Non-Combustible Finish Material 0-4 Inches Thick
3/4 IN.
3/4 IN.
FACTORY-INSTALLED
NON-COMBUSTIBLE
BOARD
Bottom
Joint
0-4 IN.
Figure 13.16 Noncombustible Surface Finishing Material 0-4 Inch
Thick-Inside Fit Method (Tonic Decorative Front Only)
17-1/2 IN. APPLIANCE
OPENING (HEIGHT)
0- 4 IN.
DRYWALL OR
EQUIVALENT
(1/2 IN.)
Figure 13.14 Inside Fit Method (Tonic Decorative Front Only)
52
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Decorative Fronts
WARNING! Risk of Fire! A decorative front is required
for this model. DO NOT operate this appliance without a
decorative front in place.
Only doors certified for use with this appliance model may
be used. Contact your dealer for a list of doors that may
be used.
Inside and Overlap Fit
See Section 13.C.
TONIC DECORATIVE FRONT
(TN-SLR-**)
Figure 13.17 Tonic Decorative Front
Overlap Fit Only
See Section 13.C.
MARTINI DECORATIVE FRONT
(MT-SLR-**)
Figure 13.18 Martini Decorative Front
The tinted glass on the Martini Decorative Front meets the
tempered glass specifications in Section 1.B of this installa-
tion manual.
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Appliance Setup
14
A. Remove Fixed Glass Assembly
See Section 14F.
B. Remove the Shipping Materials
Remove shipping materials from inside or underneath the
firebox. The standard black rock media and manual bag
assembly are also shipped underneath the firebox.
C. Clean the Appliance
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
D. Accessories
Install approved accessories per instructions included
with accessories. Install approved accessories per in-
structions included with accessories. Contact your dealer
for a list of approved accessories.
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional acces-
sories with this appliance. Using non-listed accessories
could result in a safety hazard and will void the warranty.
54
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Rock Media Instructions
CAUTION
BURNER PORT SLOT MUST BE FREE OF ROCKS
Sharp Edges
• Wear protective gloves and safety
glasses during installation.
Cleaning the Rock
During shipment of the Rock Media, dust and debris can
accumulate. It is recommended that the Rock Media be
rinsed thoroughly with water to remove dust and small glass
particles. An easy method to clean the Rock Media is to
dump the rocks into a bucket and rinse thoroughly with a
garden hose. Allow the rocks to dry before installing them
into the fireplace.
Figure 14.2. Place Rock Media
Î
WARNING! Risk of Fire. DO NOT place rock media di-
rectly in front of the pilot assembly or between the burner
tracks over the burner ports..
INSTALLATION
3. Figure 14.4 shows an outline of the area in front of the
pilot assembly. No rock media may be placed in the
1. Choose 7 - 10 flat, quarter-sized, pieces of Rock Media
and set them aside. These will be used later to conceal
the pilot cover. Reference Figure 14.1 for choosing flat
pieces of glass.
outlined area. Continue to place an even amount of
Rock Media over the entire base pan. DO NOT install
Rock Media in between the tracks over the entire length
of the burner.
DO NOT PLACE ROCK MEDIA
BETWEEN BURNEER TRACKS
YES
NO
Figure 14.1. Selecting Flat Rocks for Pilot Cover.
Î
WARNING
Delayed Ignition Risk
Figure 14.3. Burner Tracks
• Place stones according to instructions.
• Do NOT place stones in area in front of pilot or
between burner tracks.
DO NOT PLACE ROCK MEDIA
IN FRONT OF PILOT ASSEMBLY
• Do NOT place stones in a position that they may
fall into area in front of pilot.
• Do NOT use any media other than the stones
supplied with this fireplace.
• Do NOT use more than one 10 lb. bag of rock
media per fireplace.
Fireplace will not function properly.
Delayed ignition may occur.
2. Place an even layer of decorative rock around the base
pan as shown in Figure 14.2. Do not place rocks in the
slot over the burner ports. See Figures 14.2 and 14.3.
This may cause lighting issues, undesirable burner
flame, or delayed ignition.
Figure 14.4. Pilot Bracket Detail
Î
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
55
4. The rock media placement jig must remain in place
while media is placed on the basepan and around the
pilot bracket.
5. Remove the rock media placement jig by removing the
screw as noted in Figure 14.5.
SCREW
Figure 14.5. Remove Screw
6. Place the flat pieces of Rock Media that were sorted out
in Step 1, carefully hide the pilot cover. See Figures
14.6 and 14.4.
Figure 14.6. Place Flat Pieces of Rock Media
Î
56
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
F. Fixed Glass Assembly
G. Install the Mesh
WARNING! Risk of Asphyxiation! Handle fixed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
The mesh front is included with the Tonic front. The Mar-
tini tinted glass front does not include mesh.
1. Remove fixed glass assembly as instructed.
2. Place glass assembly into mesh screen such that the
four mesh clips attached to the mesh assembly snap
into the four corresponding slots on the fixed glass as-
sembly.
• DO NOT strike, slam or scratch glass.
• DO NOT operate fireplace with glass removed, cracked,
broken or scratched.
• Replace as a complete assembly.
Removing Fixed Glass Assembly
1. Remove the decorative front.
H. Air Shutter Setting
2. Locate the two spring latches that are on the upper
Air shutter settings may be adjusted by a qualified install-
er at the time of installation. The air shutter is set at the
factory for minimum vertical vent run. Adjust air shutter for
longer vertical runs. See Figure 14.4.
left and right of the fireplace.
3. Use both index fingers to release spring latches. See
Figure 14.3.
4. Allow glass to tilt forward. Grasp glass on the upper
right and left sides and lift glass “up” and “out.”
• Loosen the 1/4 in. screw.
• Twist shutter to adjust
Replacing Fixed Glass Assembly
• Shutter may be open for longer horizontal vent runs.
1. Locate glide tabs on lower left and right corners.
• Do not close the air shutter more than 1/16 in. for NG or
5/16 in. for LP.
2. Grasp glass on upper right and left sides and tilt bot-
tom of glass assembly toward fireplace.
• Tighten the screw.
3. Allow of the bottom gasketing of the glass assembly
NOTICE: If sooting occurs, provide more air by opening
the air shutter.
to touch the face of the fireplace.
4. Put pressure on the glass as you allow the glass
assembly to drop into the two lower glass clips. See
Figure 14.3.
5. Tilt top of glass towards fireplace and engage both
top spring latches
UPPER SPRING LATCH
LOWER GLASS CLIP
Figure 14.4 Air Shutter
Air Shutter Settings
NG
LP
SLR
1/16 in.
5/16 in.
Figure 14.3 Fixed Glass Assembly
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
57
Troubleshooting
15
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and
the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact
your dealer to arrange a service call by a qualified service technician.
A. Intellifire Ignition System
Symptom
Possible Cause
Corrective Action
1. Pilot won’t light.
The ignitor/module
makes noise, but no
spark.
a. Incorrect wiring.
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor
are connected to correct terminals on module and pilot assembly.
b. Loose connections or electrical
shorts in the wiring.
Verify no loose connections or electrical shorts in wiring from
module to pilot assembly. Verify connections underneath pilot as-
sembly are tight; also verify connections are not grounding out to
metal chassis, pilot burner, pilot enclosure, mesh screen if present,
or any other metal object.
c. Ignitor gap is too large.
d. Module.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place a grounded wire about 3/16 in. (5
mm) away from “I” terminal on module. Place ON/OFF rocker switch
or wall switch in ON position. If there is no spark at “I” terminal
module must be replaced. If there is a spark at “I” terminal, module
is fine. Inspect pilot assembly for shorted sparker wire or cracked
insulator around electrode. Replace pilot if necessary.
2. Pilot won’t light,
there is no noise or
spark.
a. No power or transformer installed
incorrectly.
Verify that transformer is installed and plugged into module. Check
voltage of transformer under load at spade connection on module
with ON/OFF switch in ON position. Acceptable readings of a good
transformer are between 3.2 and 2.8 volts AC.
b. A shorted or loose connection in wir- Remove and reinstall the wiring harness that plugs into module.
ing configuration or wiring harness. Verify there is a tight fit. Verify pilot assembly wiring to module. Re-
move and verify continuity of each wire in wiring harness. Replace
any damaged components.
c. Improper wall switch wiring.
d. Module not grounded.
Verify that 110/VAC power is “ON” to junction box.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
e. Module.
Turn ON/OFF rocker switch or wall switch to OFF position. Re-
move ignitor wire “I” from module. Place ON/OFF rocker switch
or wall switch in ON position. If there is no spark at “I” terminal
module must be replaced. If there is a spark at “I” terminal, module
is fine. Inspect pilot assembly for shorted sparker wire or cracked
insulator around electrode.
3. Pilot sparks, but
Pilot will not light.
a. Gas supply.
Verify that incoming gas line ball valve is “open”. Verify that inlet
pressure reading is within acceptable limits, inlet pressure must
not exceed 14 in. W.C.
b. Ignitor gap is incorrect.
c. Module is not grounded.
Verify that spark gap from ignitor to pilot hood is .17 in. or 1/8 in (3 mm).
Verify module is securely grounded to metal chassis of appliance.
d. Module voltage output / Valve/Pilot Verify battery voltage is at least 2.7 volts. Replace batteries if volt-
solenoid ohms readings. age is below 2.7.
58
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Intellifire Ignition System - (continued)
Symptom
Possible Cause
Corrective Action
a. A shorted or loose connection in flame
Verify all connections to wiring diagram in manual. Verify
connections underneath pilot assembly are tight. Verify
connections are not grounding out to metal chassis, pilot
burner, pilot enclosure or screen if present, or any other
metal object.
4. Pilot lights but contin-
ues to spark, and main
burner will not ignite.
(If the pilot continues
to spark after the
pilot flame has been lit,
flame rectification has
not occurred.)
sensing rod.
b. Poor flame rectification or contaminated With fixed glass assembly in place, verify that flame is en-
flame sensing rod.
gulfing flame sensing rod on left side of pilot hood. Flame
sensing rod should glow shortly after ignition. Verify cor-
rect pilot orifice is installed and gas inlet is set to pressure
specifications. Clean flame sensing rod with emery cloth to
remove any contaminants that may have accumulated on
flame sensing rod.
c. Module is not grounded.
Verify module is securely grounded to metal chassis of
appliance. Verify that wire harness is firmly connected to
the module.
d. Damaged pilot assembly or contami-
Verify that ceramic insulator around the flame sensing
rod is not cracked, damaged, or loose. Verify connection
from flame sensing rod to white sensor wire. Clean flame
sensing rod with emery cloth to remove any contaminants
that may have accumulated on flame sensing rod. Verify
continuity with a multimeter with ohms set at lowest range.
Replace pilot if any damage is detected.
nated flame sensing rod.
e. Module.
Turn ON/OFF rocker switch or wall switch to OFF position.
Remove ignitor wire “I” from module. Place ON/OFF rocker
switch or wall switch in ON position. If there is no spark at
“I” terminal module must be replaced. If there is a spark at
“I” terminal, module is fine.
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
59
Reference Materials
16
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.
1 INCH STANDOFF
K
L
J
S
R
M
I
N
Ø
C
NON-COMBUSTIBLE ZONE
(PROVIDED WITH UNIT)
GAS LINE
ACCESS
O
H
E
D
T
F
P
U
ELECTRICAL
ACCESS
B
A
G
Q
LEFT VIEW
FRONT VIEW
RIGHT VIEW
Location
Inches Millimeters
Location
Inches
48
Millimeters
1218
1092
993
K
L
1
25
959
400
168
1060
55
A
B
C
D
E
F
G
H
I
37-3/4
15-3/4
6-5/8
41-3/4
2-3/16
6
43
M
N
O
P
Q
R
S
T
39-1/16
13-1/4
39-5/8
3-9/16
6-7/8
337
1006
90
152
438
464
657
248
174
17-1/4
18-1/4
25-7/8
9-3/4
47-1/16
9-5/16
16-3/4
1195
237
J
425
U
Figure 16.1 Appliance Dimensions
Î
60
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Vent Components Diagrams
13-7/8 in.
(352 mm)
9-1/2 in.
(241 mm)
11-5/8 in.
(295 mm)
14 in.
(356 mm)
12-1/8 in.
(308 mm)
7-1/8 in.
(181 mm)
DRC-RADIUS
5-3/4 in.
Cap Shield
(146 mm)
COOL-ADD
Cap Shield
11-7/8 in.
(302 mm)
5 in.
(127 mm)
13-7/8 in.
(352 mm)
PVK-80
DVP-BEK2
(For use with IPI and DSI appliances only.)
DVP-HPC Cap Brick Extension
Figure 16.2 DVP vent components
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
61
B. Vent Components Diagrams (continued)
6-1/2 in.
165 mm
6-1/2 in.
165 mm
6-1/2 in.
165 mm
8-3/4 in.
222 mm
9-1/4 in.
235 mm
6 in.
152 mm
6-5/8 in.
168 mm
6-5/8 in.
168 mm
SLP-45 - 45° Elbow
9-7/8 in.
251 mm
SLP90- 90° Elbow
Effective Height/Length
Pipe
SLP4
inches
4
mm
102
Effective
Height/
Length
26 in.
660 mm
SLP6
6
152
SLP12
SLP24
SLP36
SLP48
SLP6A
SLP12A
12
305
24
610
36
914
48
1219
51 - 152
51 - 305
2 - 6
2 - 12
DVP-HSM-B
Extended Heat Shield
SLP-PIPE
SLP-HVS
Horizontal Pipe
Support
RF4-8
Roof Flashing
SLP-FS
Ceiling Firestop
SLP-WS
Wall Shield Firestop
Figure 16.5 SLP Series Vent Components
62
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Vent Components Diagrams (continued)
SLP-TVHW
Vertical
Termination Cap
SLP-CCS-BK
SLK-SNKD
PVK-80
Power Vent
Cathedral Ceiling
Snorkel
Support Box-Black
Termination Cap
SLP-TRAP2
SLP-DCF-BK
SLP-WT-BK
Wall Thimble-Black
SL-2DVP
Adapter
Horizontal
Ceiling Firestop
Termination Cap
Black
8-1/8 in.
(206 mm)
13 in.
(330 mm)
Effective Length
5-3/4 to 8-3/8 in.
146 to 213 mm
5-1/2 in.
140 mm
8-3/8 in.
213 mm
3°
87°
15 in.
(381 mm)
10-1/2 in.
267 mm
10-7/8 in.
276 mm
Note: The SLP-HRC-SS and SLP-HRC-ZC-SS
termination caps are not approved for use with
propane (LP) fuel.
SLP-HRC-SS
SLP-HRC-ZC-SS
HORIZONTAL TERMINATION CAP
Figure 16.6 SLP Series Vent Components
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
63
SLR
C. Service Parts
Beginning Manufacturing Date: July 2008
Service Parts Diagram
Ending Manufacturing Date: ______
1
2
3
Î
4
5
6
8
10
7
9
Part number list on following page.
64
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Service Parts List
SLR
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
Stocked
at Depot
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
2143-168
2143-147
2143-102
2143-117
2143-115
2143-007
2143-008
2143-123
GLA-SLR
4013-021
2143-103
1
2
3
4
5
Elbow Heat Shield
Sheet Rock Ledge
n
N
N
N
N
Y
Y
n
Top Panel, Finishing Edge
Non Combustible Board
Base Pan
Burner NG
6
Burner LP
7
8
Pilot Bracket
Glass Door Assembly
Junction Box
Y
Y
N
9
10
Lower Cover Panel
SLP12
12 in Pipe
N
N
10 LB Bag
2143-850
Black Rock
Gasket Assembly
2121-080
N
Contains burner neck, shutter bracket, vent, seal cap,
valve plate, and air passage gaskets
Qty 2 req
Right
386-122A
2143-118
2143-169
TUP-GBK-12
WSK-21
Glass Latch Assembly
Y
N
Finish Edge
Left
Touch Up Paint
Wall Switch Kit
N
N
N/A
Conversion Kit NG
Conversion Kit LP
Pilot Orifice NG
Pilot Orifice LP
Regulator NG
N
Y
Y
Y
Y
Y
LPK-SLR
593-528
593-527
NGK-DXF
LPK-DXF
Regulator LP
Additional service part numbers appear on following page.
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
65
SLR
Service Parts
Beginning Manufacturing Date: July 2008
Valve Assembly Diagram/ Parts List
Ending Manufacturing Date: ______
1
IPI Valve Assembly
3
2
10
11
4
5
9
6
8
7
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
Stocked
at Depot
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
2090-012
2090-013
2118-104
302-320A
593-500
Pilot Assembly NG
Pilot Assembly LP
Valve Bracket
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
1
2
3
Flex Ball Valve Assembly
Valve NG
4
Valve LP
593-501
5
6
Module
593-592
Thermostat Wire Assembly
Module Wire Assembly
3 Volt Transformer
Bulkhead W/Flex Tube
Battery Pack
2118-170
593-590A
593-593A
7000-156
593-594A
582-842
7
8
9
10
Orifice NG (#42C)
Orifice LP (.057C)
Jumper Wires 21 in
11
582-057
2012-206
66
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Contact Information
Heat & Glo, a brand of Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
- NOTES -
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162,
5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340,
5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588,
6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940,
6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174,
D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.
Printed in U.S.A. - Copyright 2008
Heat & Glo • SLR • 2143-900 Rev. B • 7/08
Download from Www.Somanuals.com. All Manuals Search And Download.
67
|