Models:
Pier-TRC
Installers Guide
ST-TRC
L-Corner-TRC
R-Corner-TRC
Underwriters
Laboratories Listed
READ THIS MANUAL BEFORE INSTALLING OR
OPERATING THIS APPLIANCE. THIS INSTALLERS
GUIDE MUST BE LEFT WITH APPLIANCE FOR
FUTURE REFERENCE.
WARNING: IF THE INFORMATION
IN THESE INSTRUCTIONS IS NOT
FOLLOWED EXACTLY, AFIRE OR
EXPLOSION MAY RESULT CAUS-
ING PROPERTY DAMAGE, PER-
SONAL INJURY, OR DEATH.
WARNING: IMPROPER INSTALLA-
TION, ADJUSTMENT, ALTERATION,
SERVICE OR MAINTENANCE CAN
CAUSE INJURY OR PROPERTY DAM-
AGE. REFER TO THIS MANUAL. FOR
ASSISTANCE OR ADDITIONAL INFOR-
MATION CONSULT A QUALIFIED IN-
STALLER, SERVICE AGENCY, OR THE
GAS SUPPLIER.
- Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
- What to do if you smell gas
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
1. This appliance may be installed in an af-
termarket, permanently located, manufac-
tured (mobile) home, where not prohibited
by local codes.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
the fire department.
2. This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.
- Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.
Printed in U.S.A. Copyright 2003
Please contact your Heat-N-Glo dealer with any
questions or concerns. For the number of your nearest
Heat-N-Glo dealer, please call 1-888-427-3973.
Heat-N-Glo, a division of Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;
4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)
543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.
501-900 REV. O 2/03
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Safety and Warning Information ............................................... 2
Service Parts Lists.................................................................... 4
Section 1: Approvals and Codes ............................................ 12
Approval Listings and Codes ..................................................... 12
Appliance Certification ............................................................... 12
Installation Codes ...................................................................... 12
HighAltitude Installations............................................................ 12
Section 2: Getting Started ...................................................... 13
Introducing the Heat-N-Glo Gas Fireplaces ................................ 13
Pre-installation Preparation ........................................................ 13
Section 3: Installing the Fireplace ......................................... 17
Step 1 Locating the Fireplace ................................................ 17
Step 2 Framing the Fireplace................................................. 17
Step 3 Installing the Vent System ........................................... 20
u A. Vent System Approvals .......................................... 20
B. Installing Vent Components ................................... 27
C. Vent Termination.................................................... 30
Step 4 Positioning, Leveling, and
Securing the Fireplace................................................ 33
Step 5 The Gas Control Systems .......................................... 33
Step 6 The Gas Supply Line .................................................. 34
Step 7 Gas Pressure Requirements ...................................... 34
Step 8 Wiring the Fireplace.................................................... 35
Step 9 Finishing ..................................................................... 37
Step 10 Installing Trim, Logs, and Ember Material..................... 38
Installing the Trim........................................................ 38
Positioning the Logs ................................................... 38
Shutter Settings .......................................................... 38
Placing the Ember Material ......................................... 38
Step 11 Before Lighting the Fireplace ...................................... 39
Step 12 Lighting the Fireplace.................................................. 39
After the Installation.................................................................... 39
u Section 4: Maintaining and Servicing Your Fireplace......... 40
u = Contains updated information.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Pier-TRC
Beginning Manufacturing Date: 6-97
Ending Manufacturing Date: ______
Service Parts
(NG, LP) Exploded Parts Diagram
(GN, PL) Vue éclatée des pièces
16
9
15
10
Standing Pilot
3
11
1
12
5
4
3
9
14
7
6
2
8 Log Assembly
13
Part number list on following page.
*
*
La liste des numéros de pièce se trouve à la page suivante.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
(NG, LP) Exploded Parts Diagram / Vue éclatée des pièces
PIER-TRC
IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When ordering,
supply serial and model numbers to ensure correct service parts. / IMPORTANT : L'information fournie dans cette brochure n'est
valide que pendant une courte période. Les sites VIP des distributeurs disposent des renseignements les plus récents. Lors
d'une commande, veuillez fournir les numéros de série et de modèles pour un remplacement adéquat des pièces.
ITEM /
PIÈCE
SERIAL #
/ N° DE SÉRIE
PART NUMBER
/ N° DE PIÈCE
COMMON PART / PIÉCES COMMUNES
ON/OFF Rocker Switch / Interrupteur à bascule marche/arrêt
Burner Orifice NG (#32DMS) / Orifice de brûleur GN (#32DMS)
Burner Orifice LP (1.8mm) / Orifice de brûleur PL (#1.8mm)
End Glass Assembly
060-511
573-800
501-801
1
1
2
GLA-PTRC-E
GLA-PTRC
GLA-PIER
GLA-PTRC
GLA-PIER
SRV501-176A
501-173A
501-272A
PRE 8865
POST 8865
PRE 2301
POST 2301
PRE 16919
16919 to 18287
POST 18288
PRE 3666
3
3
Glass Door Assembly NG / Porte en verre GN
Glass Door Assembly LP/ Porte en verre PL
4
4
Burner Assembly NG / Brûleur GN
Burner Assembly LP / Brûleur PL
SRV501-175A
501-172A
3666 to 3984
POST 3985
501-273A
5
6
7
Log Grate / Grille de Bûche
Base Refractory / Réfractaire Base
Refractory, Rear / Réfractaire
501-364
SRV504-738-UM
SRV504-737-UM
PRE18287
LOGS-PTRC
LOGS-MS
LOGS-PTRC
LOGS-MS
NG Log Set Assembly (sold as complete log set only) / GN Jeu de Bûches
LP Log Set Assembly (sold as complete log set only) / PL Jeu de Bûches
POST 18288
8
PRE 3984
POST 3985
9
Decorative Front / Avant décoratif
DF-36H
10
12
13
14
15
16
Flex Ball Valve Assembly / Fléchir l'Assemblée de Soupape de Balle
3/8" Burner Tube / Tube de brûleur
Decorative Front (End) / Le Devant décoratif (la Fin)
Extrusion with holes / L'extrusion avec les trous
Surround Right / Entourage droit
302-320A
570-301A
DF-PTRCE
464-343
501-233
501-232
501-235
Surround Left
/
Entourage gauche
Glass Clip / Trombone de verre
STANDING PILOT IGNITION ONLY / ALLUMAGE UNE VEILLEUSE SEULEMENT
Piezo Ignitor / Allumage Piézo
Junction Box / Boîtier de raccordement
Valve NG / Valve GN
418-513
100-250A
060-522
060-523
485-510A
485-511A
446-505
446-517
446-511
Valve LP / Valve PL
11
11
Pilot Assembly NG / Module de veilleuse GN
Pilot Assembly LP / Module de veilleuse PL
Pilot Orifice NG / Orifice de veilleuse GN
Pilot Orifice LP / Orifice de veilleuse PL
Thermocouple / Thermocouple
Thermopile / Thermopile
060-512
Pilot Tube / Tube de veilleuse
SRV485-301
DSI IGNITION ONLY / ALLUMAGE DSI SEULEMENT
Junction Box / Boîtier de raccordement
Valve NG / Valve GN
Valve LP / Valve PL
Electrode / Électrode
100-254A
492-500
492-501
501-591
501-592
Module / Module
IPI IGNITION ONLY / ALLUMAGE IPI SEULEMENT
Junction Box / Boîtier de raccordement
Valve NG / Valve GN
383-250A
750-500
Valve LP / Valve PL
750-501
11
11
Pilot Assembly NG / Module de veilleuse GN
Pilot Assembly LP / Module de veilleuse PL
Wire Assembly / Module de fil
385-510A
385-511A
593-590A
593-592
Module / Module
3V Plug
593-593A
NGK-MS-IPI
LPK-MS-IPI
SRV485-301
593-594A
Conversion Kit NG / Module de conversion GN
Conversion Kit LP / Module de conversion PL
Pilot Tube / Tube de veilleuse
Battery Pack / Paquet de Batterie(Pile)
ACCESSORIES / ACCESSOIRES
Fan Kit / Module de ventilateur
GFK-160A
Remote Control Kit / Commande à distance
Remote Control Kit / Commande à distance
RC-SMART-HNG
SMART-STAT-HNG
NGK-PTRD
NGK-PTRCMS
NGK-PTRCMS-DSI
LPK-PTRD
PRE 18287
POST 18288
PRE 3984
Conversion Kit NG / Module de conversion GN
Conversion Kit LP / Module de conversion PL
LPK-PTRCMS
LPK-PTRCMS-DSI
POST 3985
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ST-TRC
Beginning Manufacturing Date: 6-97
Ending Manufacturing Date: ______
Service Parts
(NG, LP) Exploded Parts Diagram
(GN, PL) Vue éclatée des pièces
2
7
8
9
10
STANDING PILOT
4
6
1
11
2
5
3
12 Log Assembly
7
Part number list on following page.
*
*
La liste des numéros de pièce se trouve
à la page suivante.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
(NG, LP) Exploded Parts Diagram / Vue éclatée des pièces
ST-TRC
IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When ordering,
supply serial and model numbers to ensure correct service parts. / IMPORTANT : L'information fournie dans cette brochure n'est
valide que pendant une courte période. Les sites VIP des distributeurs disposent des renseignements les plus récents. Lors
d'une commande, veuillez fournir les numéros de série et de modèles pour un remplacement adéquat des pièces.
ITEM /
PIÈCE
SERIAL #
/ N° DE SÉRIE
PART NUMBER
/ N° DE PIÈCE
060-511
COMMON PARTS / I PIÉCES COMMUNES
ON/OFF Rocker Switch / Interrupteur à bascule marche/arrêt
1
1
Burner Orifice NG (#32DMS) / Orifice de brûleur GN (#32DMS)
Burner Orifice LP (1.8mm) / Orifice de brûleur PL (1.8mm)
573-800
501-801
PRE 8558
GLA-PTRC
GLA-PIER
GLA-PTRC
GLA-PIER
SRV501-176A
501-173A
501-272A
SRV501-175A
501-172A
501-273A
501-364
2
2
Glass Door Assembly NG / Porte en verre GN
Glass Door Assembly LP / Porte en verre PL
POST 8558
PRE 2254
POST 2254
PRE 16067
16067 to 18029
POST 18030
PRE 3608
3
3
Burner Assembly NG / Brûleur GN
Burner Assembly LP / Brûleur PL
3608 to 3994
POST 3995
4
5
6
Log Grate / Grille de Bûche
Base Refractory / Réfractaire Base
Refractory, Rear / Réfractaire
SRV504-738-UM
SRV504-737-UM
DF-36H
7
Decorative Front / Avant décoratif
8
9
11
Surround Side / Entourage gauche
Flex Ball Valve Assembly / Fléchir l'Assemblée de Soupape de Balle
3/8" Burner Tube / Tube de brûleur
502-202
302-320A
570-301A
PRE18029
POST 18030
PRE 3994
LOGS-PTRC
NG Log Set Assembly (sold as complete log set only) / GN Jeu de Bûches
LP Log Set Assembly (sold as complete log set only) / PL Jeu de Bûches
LOGS-MS
12
LOGS-PTRC
LOGS-MS
POST 3995
Glass Clips / Trombone de verre
STANDING PILOT IGNITION ONLY / ALLUMAGE UNE VEILLEUSE SEULEMENT
Piezo Ignitor / Allumage Piézo
Junction Box / Boîtier de raccordement
Valve NG / Valve GN
501-135
418-513
100-250A
060-522
Valve LP / Valve PL
060-523
Pilot Assembly NG / Module de veilleuse GN
Pilot Assembly LP / Module de veilleuse PL
Pilot Orifice NG / Orifice de veilleuse GN
Pilot Orifice LP / Orifice de veilleuse PL
Thermocouple / Thermocouple
485-510A
485-511A
446-505
446-517
446-511
10
10
Thermopile / Thermopile
060-512
Pilot Tube / Tube de veilleuse
SRV485-301
DSI IGNITION ONLY / ALLUMAGE DSI SEULEMENT
Junction Box / Boîtier de raccordement
Valve NG / Valve GN
Valve LP / Valve PL
Electrode / Électrode
100-254A
492-500
492-501
501-591
501-592
Module / Module
IPI IGNITION ONLY / ALLUMAGE IPI SEULEMENT
Junction Box / Boîtier de raccordement
Valve NG / Valve GN
383-250A
750-500
Valve LP / Valve PL
750-501
10
10
Pilot Assembly NG / Module de veilleuse GN
Pilot Assembly LP / Module de veilleuse PL
Wire Assembly / Module de fil
385-510A
385-511A
593-590A
593-592
Module / Module
3V Plug
593-593A
NGK-MS-IPI
LPK-MS-IPI
SRV485-301
593-594A
Conversion Kit NG / Module de conversion GN
Conversion Kit LP / Module de conversion PL
Pilot Tube / Tube de veilleuse
Battery Pack / Paquet de Batterie(Pile)
ACCESSORIES / ACCESSOIRES
Fan Kit / Module de ventilateur
GFK-160A
Remote Control Kit / Commande à distance
Remote Control Kit / Commande à distance
RC-SMART-HNG
SMART-STAT-HNG
NGK-PTRD
PRE 18029
POST 18030
PRE 3994
NGK-PTRCMS
Conversion Kit NG / Module de conversion GN
Conversion Kit LP / Module de conversion PL
NGK-PTRCMS-DSI
LPK-PTRD
LPK-PTRCMS
POST 3995
LPK-PTRCMS-DSI
7
Download from Www.Somanuals.com. All Manuals Search And Download.
L-Corner-TRC
Beginning Manufacturing Date: 6-97
Ending Manufacturing Date: ______
Service Parts
(NG, LP) Exploded Parts Diagram
(GN, PL) Vue éclatée des pièces
10
1
STANDING PILOT
12
8
11
7
5
2
15
6
14
4
9 Log Assembly
3
13
15
Part number list on following page.
La liste des numéros de pièce se trouve
à la page suivante.
*
*
8
Download from Www.Somanuals.com. All Manuals Search And Download.
(NG, LP) Exploded Parts Diagram / Vue éclatée des pièces
L-CORNER-TRC
IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When ordering,
supply serial and model numbers to ensure correct service parts. / IMPORTANT : L'information fournie dans cette brochure n'est
valide que pendant une courte période. Les sites VIP des distributeurs disposent des renseignements les plus récents. Lors
d'une commande, veuillez fournir les numéros de série et de modèles pour un remplacement adéquat des pièces.
ITEM /
PIÈCE
SERIAL #
/ N° DE SÉRIE
PART NUMBER
/ N° DE PIÈCE
COMMON PARTS / PIÉCES COMMUNES
ON/OFF Rocker Switch / Interrupteur à bascule marche/arrêt
Burner Orifice NG (#32DMS) / Orifice de brûleur GN (#32DMS)
Burner Orifice LP (1.8mm) / Orifice de brûleur PL (1.8mm)
Glass Door Assembly, End / Porte en verre
060-511
573-800
501-801
GLA-PTRC-E
GLA-PTRC
GLA-PIER
GLA-PTRC
GLA-PIER
SRV501-176A
501-173A
501-272A
1
1
2
PRE 1957
3
3
Glass Door Assembly NG / Porte en verre GN
Glass Door Assembly LP/ Porte en verre PL
POST 1957
PRE 1232
POST 1232
PRE 2920
2920 to 3102
POST 3103
PRE 1439
1439 to 1473
POST 1474
4
4
Burner Assembly NG / Brûleur GN
Burner Assembly LP / Brûleur PL
SRV501-175A
501-172A
501-273A
5
6
7
8
Log Grate / Grille de Bûche
501-364
Base Refractory / Réfractaire Base
Refractory, Rear / Réfractaire
Refractory, Back / Réfractaire
SRV504-738-UM
SRV504-737-UM
SRV504-736-UM
PRE 3102
LOGS-PTRC
NG Log Set Assembly (sold as complete log set only) / GN Jeu de Bûches
LP Log Set Assembly (sold as complete log set only) / GN Jeu de Bûches
POST 3103
LOGS-MS
9
PRE 1473
POST 1473
LOGS-PTRC
LOGS-MS
10
11
13
14
15
Surround Side Left / Entourer le Côté Part
3/8" Burner Tube / Tube de brûleur
Decorative Front / Avant décoratif
Decorative Front End / La Fin décorative de Devant
Extrusion with holes / L'extrusion avec les trous
Glass Clip / Trombone de verre
Flex Ball Valve Assembly / Fléchir l'Assemblée de Soupape de Balle
STANDING PILOT IGNITION ONLY / ALLUMAGE UNE VEILLEUSE SEULEMENT
Piezo Ignitor / Allumage Piézo
Junction Box / Boîtier de raccordement
Valve NG / Valve GN
Valve LP / Valve PL
Pilot Assembly NG / Module de veilleuse GN
Pilot Assembly LP / Module de veilleuse PL
Pilot Orifice NG / Orifice de veilleuse GN
Pilot Orifice LP / Orifice de veilleuse PL
Thermocouple / Thermocouple
501-232
570-301A
DF-36H
DF-PTRCE
464-343
501-135
302-320A
418-513
100-250A
060-522
060-523
485-510A
485-511A
446-505
446-517
446-511
12
12
Thermopile / Thermopile
Pilot Tube / Tube de veilleuse
060-512
SRV485-301
DSI IGNITION ONLY / ALLUMAGE DSI SEULEMENT
Junction Box / Boîtier de raccordement
Valve NG / Valve GN
Valve LP / Valve PL
100-254A
492-500
492-501
Electrode / Électrode
501-591
501-592
Module / Module
IPI IGNITION ONLY / ALLUMAGE IPI SEULEMENT
Junction Box / Boîtier de raccordement
Valve NG / Valve GN
383-250A
750-500
Valve LP / Valve PL
750-501
12
12
Pilot Assembly NG / Module de veilleuse GN
Pilot Assembly LP / Module de veilleuse PL
Wire Assembly / Module de fil
Module / Module
385-510A
385-511A
593-590A
593-592
3V Plug
593-593A
NGK-MS-IPI
LPK-MS-IPI
SRV485-301
593-594A
Conversion Kit NG / Module de conversion GN
Conversion Kit LP / Module de conversion PL
Pilot Tube / Tube de veilleuse
Battery Pack / Paquet de Batterie(Pile)
ACCESSORIES / ACCESSOIRES
Fan Kit / Module de ventilateur
GFK-160A
Remote Control Kit / Commande à distance
Remote Control Kit / Commande à distance
RC-SMART-HNG
SMART-STAT-HNG
NGK-PTRD
NGK-PTRCMS
LPK-PTRD
LPK-PTRCMS
PRE 3102
POST 3103
PRE 1472
POST 1473
Conversion Kit NG / Module de conversion GN
Conversion Kit LP / Module de conversion PL
9
Download from Www.Somanuals.com. All Manuals Search And Download.
R-Corner-TRC
Beginning Manufacturing Date: 6-97
Ending Manufacturing Date: ______
Service Parts
(NG, LP) Exploded Parts Diagram
(GN, PL) Vue éclatée des pièces
11
13
1
10
12
STANDING PILOT
7
8
2
5
15
6
3
14
16
4
9 Log Assembly
Part number list on following page.
La liste des numéros de pièce se trouve
à la page suivante.
*
*
10
Download from Www.Somanuals.com. All Manuals Search And Download.
(NG, LP) Exploded Parts Diagram / Vue éclatée des pièces
R-CORNER-TRC
IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When ordering,
supply serial and model numbers to ensure correct service parts. / IMPORTANT : L'information fournie dans cette brochure n'est
valide que pendant une courte période. Les sites VIP des distributeurs disposent des renseignements les plus récents. Lors
d'une commande, veuillez fournir les numéros de série et de modèles pour un remplacement adéquat des pièces.
ITEM /
PIÈCE
SERIAL # /
N° DE SÉRIE
PART NUMBER
/ N° DE PIÈCE
COMMON PARTS / PIÉCES COMMUNES
ON/OFF Rocker Switch / Interrupteur à bascule marche/arrêt
060-511
1
1
2
Burner Orifice NG (#32DMS) / Orifice de brûleur GN (#32DMS)
573-800
501-801
GLA-PTRC-E
Burner Orifice LP (1.8mm)
/
Orifice de brûleur PL (1.8mm)
Glass Door Assembly, End / Porte en verre
PRE 2132
GLA-PTRC
GLA-PIER
GLA-PTRC
GLA-PIER
SRV501-176A
501-173A
3
3
Glass Door Assembly NG / Porte en verre GN
POST 2132
PRE 1240
POST 1240
PRE 3178
3178 to 3355
POST 3356
Glass Door Assembly NG / Porte en verre GN
Burner Assembly NG / Brûleur GN
4
4
501-272A
PRE 1427
1427 to 1478
POST 1479
SRV501-175A
501-172A
501-273A
Burner Assembly LP / Brûleur PL
5
6
7
8
Log Grate
Base Refractory
Refractory, Rear / Réfractaire
Refractory, Back Réfractaire
/
Grille de Bûche
501-364
/
Réfractaire Base
SRV504-738-UM
SRV504-737-UM
SRV504-736-UM
/
PRE 3355
POST 3356
PRE 1478
POST 1479
LOGS-PTRC
LOGS-MS
LOGS-PTRC
LOGS-MS
320-320A
570-301A
501-232
NG Log Set Assembly / GN Jeu de Bûches
9
LP Log Set Assembly / PL Jeu de Bûches
10
12
13
14
Flex Ball Valve Assembly / Fléchir l'Assemblée de Soupape de Balle
3/8" Burner Tube
Surround Right / Entourage droit
Decorative Front End La Fin décorative de Devant
Extrusion with holes / L'extrusion avec les trous
Decorative Front Avant décoratif
/
Tube de brûleur
/
DF-PTRCE
464-343
15
16
/
DF-36H
501-135
Glass Clips / Trombone de verre
STANDING PILOT IGNITION ONLY
Piezo Ignitor
Junction Box
/
/
Allumage Piézo
Boîtier de raccordement
418-513
100-250A
060-522
060-523
485-510A
485-511A
446-505
446-517
446-511
Valve NG
Valve LP
/
/
Valve GN
Valve PL
11
11
Pilot Assembly NG
Pilot Assembly LP / Module de veilleuse PL
Pilot Orifice NG
Pilot Orifice LP
Thermocouple
/
Module de veilleuse GN
/
/
Orifice de veilleuse GN
Orifice de veilleuse PL
/
Thermocouple
Thermopile
Pilot Tube
/
Thermopile
Tube de veilleuse
060-512
SRV485-301
/
DSI IGNITION ONLY
/
ALLUMAGE DSI SEULEMENT
Junction Box Boîtier de raccordement
/
100-254A
492-500
492-501
501-591
501-592
Valve NG
Valve LP
Electrode
/
/
/
Valve GN
Valve PL
Électrode
Module / Module
IPI IGNITION ONLY / ALLUMAGE IPI SEULEMENT
Junction Box
/
Boîtier de raccordement
383-250A
750-500
750-501
Valve NG
Valve LP
/
/
Valve GN
Valve PL
11
11
Pilot Assembly NG
/
Module de veilleuse GN
385-510A
385-511A
593-590A
593-592
Pilot Assembly LP / Module de veilleuse PL
Wire Assembly / Module de fil
Module / Module
3V Plug
593-593A
NGK-MS-IPI
LPK-MS-IPI
SRV485-301
593-394A
Conversion Kit NG / Module de conversion GN
Conversion Kit LP / Module de conversion PL
Pilot Tube
Battery Pack / Paquet de Batterie(Pile)
ACCESSORIES ACCESSOIRES
Fan Kit Module de ventilateur
/
Tube de veilleuse
/
/
GFK-160A
Remote Control Kit / Commande à distance
Remote Control Kit / Commande à distance
RC-SMART-HNG
SMART-STAT-HNG
NGK-PTRD
NGK-PTRCMS
NGK-PTRCMS-DSI
LPK-PTRD
PRE 3355
POST 3356
PRE 1478
POST 1479
Conversion Kit NG / Module de conversion GN
Conversion Kit LP / Module de conversion PL
LPK-PTRCMS
LPK-PTRCMS-DSI
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Approvals and
Codes
High Altitude Installations
Appliance Certification
U.L. Listed gas appliances are tested and approved with-
out requiring changes for elevations from 0 to 2,000 feet in
the U. S. A. and in Canada.
The Heat-N-Glo fireplace models discussed in this Installers
Guide have been tested to certification standards and listed
by the applicable laboratories.
When installing this appliance at an elevation above 2,000
feet, it may be necessary to decrease the input rating by
changing the existing burner orifice to a smaller size. Input
rate should be reduced by 4% for each 1000 feet above a
2000 foot elevation in the U.S.A. or 10% for elevations
between 2000 and 4500 feet in Canada. If the heating value
of the gas has been reduced, these rules do not apply. To
identify the proper orifice size, check with the local gas
utility.
Certification
MODELS: PIER-TRC, ST-TRC,
L-CORNER-TRC, R-CORNER-TRC
LABORATORY: Underwriters Laboratories
TYPE: Direct Vent Gas Fireplace
STANDARD: ANSI Z21.50•CGA2.22•UL307B
Installation Codes
If installing this appliance at an elevation above 4,500 feet
(in Canada), check with local authorities.
The fireplace installation must conform to local codes. Before
installing the fireplace, consult the local building code
agency to ensure that you are in compliance with all
applicable codes, including permits and inspections.
In the absence of local codes, the fireplace installation must
conform to the National Fuel Gas Code ANSI Z223.1 (in
the United States) or the CAN/CGA-B149 Installation Codes
(in Canada). The appliance must be electrically grounded
in accordance with local codes or, in the absence of local
codes with the National Electric Code ANSI/NFPA No. 70
(in the United States), or to the CSA C22.1 Canadian Electric
Code (in Canada).
These models may be installed in a bedroom or bed-sitting
room in the U.S.A. and Canada.
Heat-N-Glo Quality
Systems registered
by SGS ICS
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Introducing the Heat-N-Glo Gas Fireplaces
The Heat-N-Glo Warranty will be voided by, and Heat-N-Glo
disclaims any responsibility for, the following actions:
Heat-N-Glo direct vent gas fireplaces are designed to oper-
ate with all combustion air siphoned from outside of the
building and all exhaust gases expelled to the outside.
•
Installation of any damaged fireplace or vent system
component.
•
•
•
•
Modification of the fireplace or direct vent system.
Installation other than as instructed by Heat-N-Glo.
Improper positioning of the gas logs or the glass door.
The information contained in this Installers Guide, unless
noted otherwise, applies to all models and gas control
systems. Gas fireplace diagrams, including the dimensions,
are shown in this section.
Installation and/or use of any component part not manu-
factured and approved by Heat-N-Glo, not withstanding
any independent testing laboratory or other party approval
of such component part or accessory.
Pre-install Preparation
This gas fireplace and its components are tested and safe
when installed in accordance with this Installers Guide.
Report to your dealer any parts damaged in shipment,
particularly the condition of the glass. Do not install any
unit with damaged, incomplete, or substitute parts.
ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE
HAZARD.
When planning a fireplace installation, it’s necessary to
determine:
The vent system components are shipped in separate pack-
ages. The gas logs are packaged separately and must be
field installed.
• Where the unit is to be installed.
• The vent system configuration to be used.
• Gas supply piping.
Read all of the instructions before starting the instal-
lation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
Failure to follow these instructions will void the own-
er’s warranty and may present a fire hazard.
• Electrical wiring.
• Framing and finishing details.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
If the fireplace is to be installed on carpeting or tile, or on
any combustible material other than wood flooring, the
fireplace should be installed on a metal or wood panel that
extends the full width and depth of the fireplace.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
13 (331mm)
24 1/4 (616mm)
12 1/8 (308mm)
VENT COLLARS
42 3/4 (1086mm)
ELECTRICAL
ACCESS
GAS LINE
ACCESS
41
(1043mm)
36 7/8
(937mm)
28 7/8
(735mm)
2 1/2
2 1/2
(6mm)
(64mm)
36 7/8 (937mm)
40 3/4 (1035mm)
FRONT
24 1/4 (616mm)
4 (102mm)
4 (102mm)
LEFT SIDE
RIGHT SIDE
TOP STANDOFFS
TOP VENT
COLLARS
REAR
COLLARS
TOP GRILLE
SIDE GLASS
DOOR
END GLASS
DOOR
BOTTOM
GRILLE
GAS CONTROLS
& LABELS
ELECTRICAL
ACCESS
GAS LINE
ACCESS
Figure 1. Diagram of the PIER-TRC
14
Download from Www.Somanuals.com. All Manuals Search And Download.
45 (1143mm)
13 (330mm)
24 1/4
(616mm)
12 1/8 (308mm)
VENT COLLARS
41
ELECTRICAL
ACCESS
(1042mm)
GAS LINE
ACCESS
36 7/8
(937mm)
28 7/8
(733mm)
2 1/2
(64mm)
2 1/2
(64mm)
36 1/8 (918mm)
43 (1093mm)
4 (102mm)
4 (102mm)
24 1/4 (616mm)
RIGHT SIDE
FRONT
LEFT SIDE
TOP VENT
COLLARS
REAR VENT
COLLARS
TOP STANDOFFS
TOP GRILLE
GLASS DOOR
BOTTOM
GRILLE
GAS CONTROLS
& LABELS
ELECTRICAL
ACCESS
GAS LINE
ACCESS
Figure 2. Diagram of the ST-TRC
15
Download from Www.Somanuals.com. All Manuals Search And Download.
42 3/4 (1086mm)
13 (330mm)
25 1/4 (642mm)
12 1/8 (308mm)
VENT COLLARS
41 (1041mm)
ELECTRICAL
ACCESS
GAS LINE
ACCESS
28 7/8
(733mm)
36 7/8 (937mm)
2 1/2
(64mm)
2 /12/
(64mm)
36 1/8 (918mm)
40 3/4 (1034mm)
FRONT
4 (102mm)
4 (102mm)
24 1/4 (616mm)
LEFT SIDE
RIGHT SIDE
TOP VENT
COLLARS
REAR VENT
COLLARS
TOP STANDOFFS
TOP GRILLE
SIDE GLASS
DOOR
END GLASS
DOOR
BOTTOM
GRILLE
GAS CONTROLS
& LABELS
GAS LINE
ACCESS
ELECTRICAL
ACCESS
Figure 3. Diagram of the L & R CORNER-TRC
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Fireplace
Step 1.
Locating the Fireplace
Minimum Clearances
from the Fireplace to Combustible Materials
The diagram below shows space and clearance require-
ments for locating a fireplace within a room.
Inches
mm
Glass Sides or Ends .......... 36 ..................... 914
Floor ....................................0........................ 0
Rear Vent ............................1....................... 25
Metal Sides or Ends .......... 1/2 ..................... 13
Top ....................................4 1/2....................114
Ceiling* ............................... 31 ..................... 787
GLASS
GLASS
R-CORNER-TRC
TOP VIEW
PIER-TRC
TOP VIEW
GLASS
* The clearance to the ceiling is measured from the top
of the unit, excluding the standoffs (see Figure 35).
36"
GLASS
GLASS
36"
36"
The distance from the unit to combustible construction is to
be measured from the unit outer warp surface to the com-
bustible construction, NOT from the screw heads that se-
cure the unit together.
Minimum Clearances
from the Vent Pipe to Combustible Materials
36"
36"
GLASS
GLASS
Inches
mm
Vertical Sections............... 1................. 25
Horizontal Sections
ST-TRC
TOP VIEW
L-CORNER-TRC
TOP VIEW
Top ...................................... 3................. 75
Bottom ................................ 1................. 25
Sides .................................. 1................. 25
GLASS
1"
GLASS
At Wall Firestops
Top ................................... 2 1/2.............63.7
Bottom .............................. 1/2 ............... 13
Sides .................................. 1................. 25
Figure 4. Fireplace Dimensions and Locations
Clearance Requirements
For minimum clearances, see the direct vent termination
clearance diagrams on pages 27 and 28 in this manual.
The top, back, and sides of the fireplace are defined by
stand-offs. The minimum clearance to a perpendicular wall
extending past the face of the fireplace is one inch (25 mm).
The metal ends of the fireplace may NOT be recessed into
combustible construction.
Step 2. Framing the Fireplace
Fireplace framing can be built before or after the fireplace is
set in place. Framing should be positioned to accommo-
date wall coverings and fireplace facing material. The dia-
gram below shows framing reference dimensions.
CAUTION: MEASURE FIREPLACE DIMENSIONS AND
VERIFY FRAMING METHODS AND WALL COVERING
DETAILS BEFORE FRAMING.
WARNING: FRAMING DIMENSIONS ASSUME
USE OF 1/2 INCH THICK WALL COVERING
!
MATERIALS ON EXTERIOR OF FRAMING ONLYAND
NO SHEETROCK ON INTERIOR OF FRAMING.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Shows center of 12” x 12” vent
framing holes for top and rear
venting. The center of the hole is
one inch (25.4mm) above the
center of the horizontal vent pipe.
CORNER-TRC'S
B
E
D
A
C
Framing should be
constructed of 2 X 4
lumber or heavier.
ST-TRC
PIER-TRC
CORNER-TRC'S
B
B
C
A
A
C
Model
A
B
C
D
E
VENTED
TOP
VENTED
REAR
PIER-TRC
ST-TRC
43 1/4
47
40 1/4
46
41 1/2
41 1/2
41 1/2
23 1/4 45
23 1/4 45
24 3/4 45
29 7/8
29 7/8
29 7/8
CORNER-TRC’S
43 1/4
40 1/4
NOTE: DIMENSIONS SHOWN IN INCHES
Figure 5. Framing Dimensions
18
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7/16”
(16
8 1/2
”
4mm)
6
5/32”
(216m
m)
(1
56mm)
8 1
/2”
(216
mm)
11 5
/8”
(295m
m)
7 3
/8”
5 7/
8”
(149m
11 1/16
”
)
6 1/2
”
(187
mm)
5 1
/16”
(129
mm)
m)
(2
81mm
(165m
m)
8 5/8”
(220mm)
8
5/8”
(220
mm)
11 15
/16”
(303m
m)
D
V-90D
DV-45D
35 3/4”
(908mm)
47 3/4”
(1.2m)
DV
-48D
D
V-36D
11 3/4”
(298mm)
8 3/4”
(222mm)
5 3/4”
(146mm)
DV-09D
DV-12D
DV-06D
NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm) AT EACH JOINT.
Figure 6.
D-Series Direct Vent Component Specifications (5-inch inner pipe / 8 5/8-inch outer pipe)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3. Installing the Vent System
Identifying Vent Components
The vent systems installed on this gas fireplace may in-
clude one, two, or three 90° elbow assemblies. The rela-
tionships of vertical rise to horizontal run in vent configura-
tions using 90° elbows MUST BE strictly adhered to. The
rise to run relationships are shown in the venting drawings
and tables. Refer to the diagrams on the next several pages.
A. Vent System Approvals
These models are approved to use D-series direct vent pipe
components and terminations (see Figures 6 and 7). Ap-
proved vent system components are labeled for identifica-
tion. This pipe is tested and listed as an approved compo-
nent of the fireplace. The pipe is tested to be run inside an
enclosed wall. There is no requirement for inspection open-
ings at each joint within the wall. There is no required pitch
for horizontal vent runs. NO OTHER VENTING SYSTEMS
OR COMPONENTS MAY BE USED.
NOTE: Two 45° elbows may be used in place of one
90° elbow. Rise to run ratios in the vent system must
be followed if 45° elbows are used.
This model has vent starting collars on both the top and the
back of the unit. Depending upon the installation, decide
which ONE set of starting collars will be used to attach the
vent system. The starting collar sealing cap must remain
on the starting collars NOT used.
Detailed installation instructions are included with each vent
termination kit and should be used in conjunction with this
Installers Guide.
The flame and ember appearance may vary based on the
type of fuel burned and the venting configuration used.
VERTICAL
TERMINATION
STORM COLLAR
ROOF FLASHING
HORIZONTAL
TERMINATION
HORIZONTAL PIPE
SUPPORT
PIPE LENGTH
WALL FIRESTOP
CEILING
FIRESTOP
WALL BRACKET
Termination kits
90 DEGREE
ELBOW
DVK-01D
DVK-TVCD
DVK-SNKD
PVK-80
DVK-01TRD
u
Figure 7. Vent System Components and Termination Kits
20
Download from Www.Somanuals.com. All Manuals Search And Download.
CAP
STRAIGHT UP
VERTICAL VENTING
V (FT.)
40' MAX. (12.4 M)
Figure 8.
Straight Up Vertical Venting
STRAIGHT OUT
HORIZONTAL VENTING
H
Max. Run
24" (610 mm)
H
Figure 9.
Straight Out Horizontal Venting
21
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING WITH
ONE (1) 90° ELBOW
V
H
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
2' MAX. (610mm)
4' MAX. (1.22m)
6' MAX. (1.86m)
8' MAX. (2.4m)
V
V+H=37' MAX. (11.3m)
H = 8' MAX. (2.4m)
H
Figure 10. Venting with One 90° Elbow
VENTING WITH ONE (1) 90° ELBOW
V (FT.)
H (FT.)
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
5’ MIN. (1.5m)
3' MAX. (914mm)
6' MAX. (1.86m)
9' MAX. (2.7m)
12' MAX. (3.6m)
15’ MAX. (4.5m)
17’ MAX. (5.1m)
17' MAX. (5.1m)
6’ MIN. (1.86m)
H
V + H = 37’ MAX. (11.3m)
V
Figure 11. Venting with One 90° Elbow
22
Download from Www.Somanuals.com. All Manuals Search And Download.
H1
V
H
VENTING WITH TWO (2) 90° ELBOWS
1
V (FT.)
H + H (FT.)
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
5' MIN. (1.5m)
3' MAX. (914mm)
6' MAX. (1.86m)
9' MAX. (2.7m)
12' MAX. (3.6m)
15' MAX. (4.5m)
17' MAX. (5.1m)
17' MAX. (5.1m)
6' MIN. (1.86m)
V + H = 37' MAX. (11.3m)
H
V1
V
VENTING WITH TWO (2) 90° ELBOWS
V (FT.)
H (FT.)
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
3' MAX. (914m)
6' MAX. (1.86m)
9' MAX. (2.7m)
12' MAX. (3.6m)
17' MAX. (5.1m)
NOTE: V + V1 + H = 37' MAX. (11.3m)
Figure 12. Venting with Two 90° Elbows
23
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING WITH TWO (2) 90° ELBOWS
V
H
H + H1
1' MIN. (305 mm)
2' MIN. (610 mm)
3' MIN. (914 mm)
4' MIN. (1.22 m)
2' MAX. (610 mm)
4' MAX. (1.22 m)
6' MAX. (1.86 m)
8' MAX. (2.48 m)
8' MAX. (2.48 m)
3' MAX. (914 mm)
6' MAX. (1.86 m)
9' MAX. (2.7 m)
12' MAX. (3.6 m)
17' MAX. (5.1 m)
H1
V = 37' MAX. (11.3m)
V
H
Figure 13.
Venting with Two 90° Elbows
VENTING WITH TWO (2) 90o ELBOWS
V FT.
H + H1 (FT.)
2' MAX. (610mm)
4' MAX. (1.22m)
6' MAX. (1.86m)
8' MAX. (2.4m)
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
8' MAX. (2.4m)
V + H + H1 + 37' MAX. (11.3m)
V
H
H1
Figure 14. Venting with Two 90° Elbows
24
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING WITH THREE (3) 90° ELBOWS
VENTING WITH THREE (3) 90° ELBOWS
1' MIN. (305 mm)
2' MIN. (610 mm)
3' MIN. (914 mm)
4' MIN. (1.22 m)
2' MAX. (610 mm)
4' MAX. (1.22 m)
6' MAX. (1.86 m)
8' MAX. (2.48 m)
3' MAX. (914mm)
6' MAX. (1.86 m)
9' MAX. (2.7 m)
12' MAX. (3.6 m)
8' MAX. (2.48 m)
V + V1 + H + H1 = 37' MAX. (11.3m)
17' MAX. (5.1 m)
V1
V
H
VENTING WITH THREE (3) 90° ELBOWS
H1
V
H
H + H1 + H2
3' MAX. (914 mm)
1' MIN. (305 mm)
2' MIN. (610 mm)
3' MIN. (914 mm)
4' MIN. (1.22 m)
2' MAX. (610 mm)
4' MAX. (1.22 m)
6' MAX. (1.86 m)
8' MAX. (2.48 m)
6' MAX. (1.86 m)
9' MAX. (2.7 m)
15' MAX. (4.5 m)
8' MAX. (2.48 m)
17' MAX. (5.1 m)
V + H + H1 + H2 = 37' MAX. (11.3m)
H2
V
H1
H
Figure 15. Venting with three 90° elbows
25
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING WITH THREE (3) 90° ELBOWS
V (FT.)
H (FT.)
1' MIN. (305mm)
3' MAX. (914mm)
2' MIN. (610mm)
3' MIN. (914mm)
6' MAX. (1.86m)
9' MAX. (2.7m)
H
4' MIN. (1.22m)
12' MAX. (3.6m)
17' MAX. (5.1m)
NOTE: H + H1 = 17' MAX. (5.1m)
V + V1 + H + H1 = 37' MAX. (11.3m)
H1
V1
V
V1
V
H1
H
VENTING WITH THREE (3) 90° ELBOWS
V (FT.)
H + H1 (FT.)
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
3' MAX. (914m)
6' MAX. (1.86m)
9' MAX. (2.7m)
12' MAX. (3.6m)
17' MAX. (5.1m)
NOTE: V + V1 + H + H1 = 37' MAX. (11.3m)
Figure 16. Venting with three 90° elbows
26
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Installing Vent Components
After determining which set of starting collars will be used
(top or rear), follow venting instructions accordingly.
1. Attach the First Vent Component to the
Starting Collars
To attach the first vent component to the starting collars
of the fireplace:
Venting Out the Rear Vent
Remove the installed rear seal cap from the rear starting
collars by removing screws (see Figure 17). Follow the vent
configuration tables accordingly.
• Apply a 3/8 inch (9.5mm) bead of stove cement around
the 5 inch (127mm) fireplace starting collar.
Remove the insulation from the REAR five inch flue, pull
the heat shield out from outside of the firebox.
• Make sure that the fireplace rope gasket supplied with
the fireplace seals between the first 8-5/8 inch (219mm)
vent component and the outer fireplace wrap.
WARNING: THE TOP HEAT SHIELD (INSIDE
THE FIREBOX) MUST REMAIN ATTACHED IF
THE VENT SYSTEM IS ATTACHED TO THE
REAR STARTING COLLARS. SEE FIGURE 17.
!
• Lock the vent components into place by sliding the con-
centric pipe sections with four (4) equally spaced interior
beads into the fireplace collar or previously installed com-
ponent end with four (4) equally spaced indented sections.
Venting Out the Top Vent
Remove the screws in the top vent collar seal cap and re-
move the top vent collar seal cap and insulation inside the
top starting collar (See Figure 17).
• When the internal beads of each 8-5/8 inch (219mm)
outer pipe line up, rotate the pipe section clockwise about
one-quarter (1/4) turn. The vent pipe is now locked together.
Remove the heat shield from inside the TOP five inch flue
from outside of the firebox.
The glass must be taken off again for positioning the logs
when the unit is finally installed in place and finished around
it. Re-install the glass door. Attach vent system to the top
starting collars.
STARTING
COLLAR
WARNING: THE REAR VENT COLLAR SEAL
CAP MUST REMAINATTACHED TO THE REAR
VENT COLLARS IF THE VENT SYSTEM IS AT-
!
TACHED TO THE TOP STARTING COLLARS.
WARNING: FAILURE TO REMOVE INSULATION
IN THE SET OF COLLARS YOU ARE USING
COULD CAUSE A FIRE.
!
STOVE
SEALANT
BEAD
WARNING:YOU MUST LEAVE THE INSULATION
IN PLACE IN THE SET OF COLLARS YOU ARE
!
FIRST VENT
COMPONENT
NOT USING.
1 INCH
(25.4mm)
If your vertical vent component is over 10 feet, you may
want to install the vertical baffle (located in the bag containing
the install manual) to improve flame appearance. Center
the vertical baffle on the 5” flue being used, and with self
tapping screws secure the baffle to the inside of the firebox.
Figure 18. Attaching the First Vent Component
to the Starting Collars
WARNING: A 3/8 INCH (9.5 MM) BEAD OF
!
STOVE CEMENT MUST BE PLACED AROUND
THE 5 INCH (127 MM) FIREPLACE STARTING COL-
LAR BEFORE ATTACHING THE FIRST VENT COM-
PONENT. FAILURE TO SEAL THIS JOINT MAY
CAUSE THE FIREPLACE TOOPERATEIMPROPERLY.
SEE THE DIAGRAM .
Venting Out Top
Venting Out Rear
SEAL
CAP
SEAL
CAP
HEAT
SHIELD
DISCARD
INSULATION
and
WARNING: ENSURE THAT THE FIBER-
GLASS ROPE GASKET SUPPLIED WITH
THE FIREPLACE SEALS BETWEEN THE FIRST
VENT COMPONENT AND THE OUTER FIREPLACE
WRAP.
HEAT SHIELD
HEAT
SHIELD
!
DISCARD
INSULATION
and
HEAT SHIELD
If the installation is for a termination cap attached directly
to the fireplace, skip to the sections, Install Firestops and
Vent Termination.
Figure 17
27
Download from Www.Somanuals.com. All Manuals Search And Download.
2. ContinueAdding Vent Components
WALL BRACKET
WALL STUD
• Continue adding vent components, locking each succeed-
ing component into place.
• Ensure that each succeeding vent component is secure-
ly fitted and locked into the preceding component in the
vent system.
• 90° elbows may be installed and rotated to any point
around the preceding component’s vertical axis. If an el-
bow does not end up in a locked position with the pre-
ceding component, attach with a minimum of two (2)
sheet metal screws.
8 FT. (2.4 m)
FLUE
OUTLET
1 INCH MIN.
(25.4 mm)
Figure 19. Adding Venting Components
3. Install Support Brackets
Figure 20. Installing Support Brackets
For Horizontal Runs - The vent system must be supported
every five (5) feet of horizontal run by a horizontal pipe support.
12"
(305mm)
To install support brackets for horizontal runs:
• Place the pipe supports around the vent pipe.
• Nail the pipe supports to the framing members.
For Vertical Runs - The vent system must be supported
every eight (8) feet (2.4m) above the fireplace flue outlet by
wall brackets.
12"
(305mm)
1" (25.4 mm)
To install support brackets for vertical runs:
• Attach wall brackets to the vent pipe and secure the wall
bracket to the framing members with nails or screws.
4. Install Firestops
VENT PIPE
For Horizontal Runs - Firestops are REQUIRED on both
sides of a combustible wall through which the vent passes.
Figure 21. 12" x 12" Hole and Vent Pipe
NOTE: Model DVK-01TRD does not need an exterior
firestop on an exterior combustible wall. The firestop is
built into the cap.
HEAT SHIELD
TRIM HEAT
SHIELD IF TOO
To install firestops for horizontal runs that pass through either
interior or exterior walls:
LONG, ADD TO
SHIELD IF TOO
SHORT
• Cut a 12” x 12” (305mm X 305mm) hole through the wall.
NOTE: The center of the hole is one (1) inch (25.4mm)
above the center of the horizontal vent pipe.
EXTERIOR
FIRESTOP
INTERIOR
FIRESTOP
• Position the firestops on both sides of the hole previ-
ously cut and secure the firestops with nails or screws.
• The heat shields of the firestops MUST BE placed to-
wards the top of the hole.
• Continue the vent run through the firestops.
NOTE: There must be NO INSULATION or other
combustibles inside the framed firestop opening.
Figure 22. Heat Shield, Interior & Exterior Firestops
28
Download from Www.Somanuals.com. All Manuals Search And Download.
For Vertical Runs - One ceiling firestop is REQUIRED at
the hole in each ceiling through which the vent passes.
If the area above the ceiling is NOT an attic, position and
secure the ceiling firestop on the ceiling side of the previously
cut and framed hole.
To install firestops for vertical runs that pass through ceilings:
• Position a plumb bob directly over the center of the verti-
cal vent component.
• Mark the ceiling to establish the centerpoint of the vent.
• Drill a hole or drive a nail through this centerpoint.
JOIST
• Check the floor above for any obstructions, such as wir-
ing or plumbing runs.
• Reposition the fireplace and vent system, if necessary,
to accommodate the ceiling joists and/or obstructions.
CEILING
• Cut an 11-inch X 11-inch (280mm X 280mm) hole through
the ceiling, using the centerpoint previously marked.
NAILS (4 REQUIRED)
CEILING FIRESTOP
• Frame the hole with framing lumber the same size as the
ceiling joists.
Figure 24. Ceiling Firestop (Ceiling Side)
11" (280 mm)
If the area above the ceiling IS an attic, position and secure
11" (280mm)
the firestop on top of the previously framed hole.
NOTE: Keep insulation away from the vent pipe at least
1 inch (25mm).
CHIMNEY
HOLE
NOTE: There must be NO INSULATION or other
combustibles inside the framed firestop opening.
EXISTING CEILING
JOISTS
NEW
FRAMING
MEMBERS
CEILING
NAILS (4 REQUIRED)
Figure 23. Hole & New Framing Members
RAFTER
CEILING
CEILING FIRESTOP
Figure 25. Attic Firestop
29
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Vent Termination
For Horizontal Terminations - To attach and secure the
ROUND CAP TERMINATION
termination to the last section of horizontal vent:
• Rotate and interlock the ends as described at the begin-
ning of the Installing Vent Components section.
PERFORATION CANNOT BE
INSIDE THE WALL
• The termination kit should pass through the wall firestops
from the exterior of the building.
• Adjust the termination cap to its final exterior position on
the building.
WARNING: THE TERMINATION CAP MUST BE
POSITIONED SO THAT THE ARROW IS
POINTING UP.
!
7 1/2"
(191mm)
MINIMUM
For roundcap termination kits:
• Use the exterior pipelock hole on the round flange of the
wall firestop to secure the vent pipe in place.
For trapezoidal cap termination kits:
TRAPEZOID CAP TERMINATION
• Using screws secure the cap to the exterior wall through
the flanges in the cap.
WARNING: THE BOTTOM OF THE VENT
TERMINATION CAP MUST BE A MINIMUM
!
OF 12 INCHES (305 MM) ABOVE GROUND LEVEL
(GRADE). THE TOP OF THE CAP MUST BE A MIN-
IMUM OF 24 INCHES (690MM) BELOW COMBUS-
TIBLE MATERIAL, SUCH AS A DECK. THE SIDE
OF THE CAP MUST BE A MINIMUM OF 6 INCHES
(152 MM) AWAY FROM A PARALLEL OUTSIDE
WALL. VENTING TERMINALS SHALL NOT BE RE-
CESSED INTOAWALL OR SIDING. SEE THE VENT
TERMINATION DIAGRAM FOR VENT TERMINATION
CLEARANCES.
7 1/4"
(184mm)
Figure 26. Round & Trapezoid Termination Caps
30
Download from Www.Somanuals.com. All Manuals Search And Download.
O
N
P
R
G
v
A
H
Q
D
(See Note 2)
E
v
B
L
U.S.
(3 FT)
B
v
v
v
B
v
F
v
M
I
v
X
A
J or K
X
= VENT TERMINAL
=AIRSUPPLY INLET
= AREA WHERE TERMINAL IS NOT PERMITTED
V
J
= 9" (U.S.A.)
A
B
= 12" ....................... clearances above grade, veran-
12" (Canada)......... clearance to non-mechani-
cal air supply inlet to build-
ing or the combustion air in-
let to any other appliance
= 3 ft. (U.S.A.)
(See Note 1)
da, porch, deck or balcony
= 12" ....................... clearances to window or door
that may be opened, or to per-
K
manently closed window.
6 ft. (Canada) ......... clearance to a mechanical
air supply inlet
D*
= 18" ....................... vertical clearance to ventilated
soffit located above the terminal
within a horizontal distance of 2
feet (60 cm) from the center-line
of the terminal
L** = 7 ft. ......................... clearance above paved
(See Note 1)
sidewalk or a paved driveway
located on public property
M*** = 18" ......................... clearance under veranda,
porch, deck or balcony
E*
F
= 18" ....................... clearance to unventilated soffit
N
O
P
= 6” ........................... non-vinyl siding
12” ......................... vinyl siding
=
9"......................... clearance to outside corner
G
H
= 6".......................... clearance to inside corner
= 18” ......................... non-vinyl soffit and overhang
60” ......................... vinyl soffit and overhang
= 3 ft. (Canada)....... not to be installed above a gas
meter/regulator assembly within
= 8 ft.
3 feet (90cm) horizontally from the
center-line of the regulator
______________________________Q___M_I_N___________________________________
_____1___c__a_p__________________3___f_e_e__t_________________2__x___Q___A_C_T_U_A_L____
______2__c__a_p__s________________6___f_e_e__t_________________1__x___Q___A_C_T_U_A_L____
______3__c__a_p__s________________9___f_e_e__t_______________2_/_3__x___Q___A_C_T_U__A_L___
4 caps 12 feet 1/2 x Q ACTUAL
RMAX
I
= 3 ft. (U.S.A.)
6 ft. (Canada) ....... clearance to service regulator
vent outlet and electric service
* 60” minimum for vinyl clad soffits.
QMIN = # termination caps x 3
RMAX = (2 / # termination caps) x QACTUAL
** a vent shall not terminate directly above a sidewalk or paved
driveway which is located between two single family dwellings
and serves both dwellings.
NOTE 3: Local codes or regulations may require different
clearances.
*** only permitted if veranda, porch, deck or balcony is fully open on
a minimum of 2 sides beneath the floor.
NOTE 4: Termination caps may be hot. Consider their proximity to
doors or other traffic areas.
NOTE 1: On private property where termination is less than 7 feet
above a sidewalk, driveway, deck, porch, veranda or balcony, use of
a listed cap shield is suggested.
WARNING: In the U.S: Vent system termination is NOT permitted
in screened porches. You must follow side wall, overhang and
ground clearances as stated in the instructions.
NOTE 2: Termination in an alcove space (spaces open only on one side
and with an overhang) are permitted with the dimensions specified for
vinyl or non-vinyl siding and soffits. 1. There must be 3 feet minimum
between termination caps. 2. All mechanical air intakes within 10 feet
of a termination cap must be a minimum of 3 feet below the termination
cap. 3. All gravity air intakes within 3 feet of a termination cap must be
a minimum of 1 foot below the termination cap.
In Canada: Vent system termination is NOT permitted in screened
porches. Vent system termination is permitted in porch areas
with two or more sides open. You must follow all side walls,
overhang and ground clearances as stated in the instructions.
Heat-N-Glo assumes no responsibility for the improper perfor-
mance of the fireplace when the venting system does not meet
these requirements.
Figure 27. Vent Termination Minimum Clearances
CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS NECESSARY TO INSTALL THE VINYL PROTECTOR
KIT TO THE TOP OF THE EXTERIOR FIRESTOP (FOR ALL ROUND TERMINATION CAPS). IT IS STRONGLY RECOMMENDED
WHENEVER POSSIBLE TO USE THE VINYL PROTECTOR KIT.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
To seal the roof hole, and to divert rain and snow from the
vent system:
For Vertical Terminations - To locate the vent and install
the vent sections:
• Locate and mark the vent centerpoint on the underside
of the roof, and drive a nail through the centerpoint.
• Attach a flashing to the roof using nails, and use a non-
hardening mastic around the edges of the flashing base
where it meets the roof.
• Make the outline of the roof hole around the centerpoint
nail.
• Attach a storm collar over the flashing joint to form a
water-tight seal. Place non-hardening mastic around the
joint, between the storm collar and the vertical pipe.
• The size of the roof hole framing dimensions depend on the
pitch of the roof. There MUST BE a 1-inch (25.4mm) clear-
ance from the vertical vent pipe to combustible materials.
• Slide the termination cap over the end of the vent pipe
and rotate the pipe clockwise 1/4 turn.
• Mark the roof hole accordingly.
HORIZONTAL
OVERHANG
• Cover the opening of the installed vent pipes.
• Cut and frame the roof hole.
2 FT.
MIN.
2 FT. MIN.
VERTICAL
WALL
• Use framing lumber the same size as the roof rafters
and install the frame securely. Flashing anchored to the
frame must withstand heavy winds.
LOWEST
DISCHARGE
OPENING
TERMINATION
CAP
• Continue to install concentric vent sections up through
the roof hole (for inside vent installations) or up past the
roof line until you reach the appropriate distance above
the roof (for outside terminations).
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
WARNING: MAJOR U.S. BUILDING CODES
SPECIFY MINIMUM CHIMNEY AND/OR
!
VENT HEIGHTABOVE THE ROOF TOP. THESE MIN-
IMUM HEIGHTS ARE NECESSARY IN THE INTER-
EST OF SAFETY. SEE THE FOLLOWING DIAGRAM
FOR MINIMUM HEIGHTS, PROVIDED THE TERMI-
NATION CAP IS AT LEAST TWO (2) FEET FROM A
VERTICAL WALLAND 2-FEET BELOW AHORIZON-
TAL OVERHANG.
Roof Pitch
H (min.) ft.
flat to 6/12
6/12 to 7/12
over 7/12 to 8/12
over 8/12 to 9/12
over 9/12 to 10/12
over 10/12 to 11/12
over 11/12 to 12/12
over 12/12 to 14/12
over 14/12 to 16/12
over 16/12 to 18/12
over 18/12 to 20/12
over 20/12 to 21/12
1.0
1.25
1.5
2.0
2.5
3.25
4.0
5.0
6.0
7.0
7.5
8.0
NOTE: This also pertains to vertical vent systems in-
stalled on the outside of the building.
Figure 28. Minimum Height from Roof to
Lowest Discharge Opening
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4. Positioning, Leveling, and
Securing the Fireplace
Step 5. The Gas Control System
WARNING: THIS UNIT IS NOT FOR USE WITH
!
The diagram below shows how to properly position, level,
and secure the fireplace.
SOLID FUEL.
Two types of gas control systems are used with these models:
Standing Pilot Ignition and Intermittent Pilot Ignition (IPI).
Standing Pilot Ignition System
This system includes millivolt control valve, standing pilot,
thermopile/thermocouple flame sensor, and piezo ignitor.
WARNING: 110-120 VAC MUST NEVER BE CON-
NECTED TOACONTROLVALVE INAMILLIVOLT
SYSTEM.
!
STANDING PILOT & IPI
NAILING TABS
Figure 29. Proper Positioning, Leveling, and
Securing of a Fireplace
• Place the fireplace into position.
• Level the fireplace from side to side and from front to
back.
Figure 30. Gas Control Systems
• Shim the fireplace with non-combustible material, such
as sheet metal, as necessary.
Intermittent Pilot Ignition (IPI) System
This system includes a 3V control valve, electronic
module and intermittent pilot.
• Secure the fireplace to the framing by nailing or screwing.
WARNING: CONTINUOUS 110-120 VAC
SERVICE MUST BE WIRED DIRECTLY TO
!
THE FIREPLACE JUNCTION BOX IN A IPI SYSTEM.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7. Gas Pressure Requirements
Step 6. The Gas Supply Line
NOTE: Have the gas supply line installed in accordance
with local building codes by a qualified installer
approved and/or licensed as required by the locality.
(In the state of Massachusetts installation must be
performed by a licensed plumber or gas fitter).
Pressure requirements for Heat-N-Glo gas fireplaces
are shown in the table below.
Pressure
Natural Gas
Propane
Minimum
Inlet Pressure
5.0 inches
w.c.
11.0 inches
w.c.
NOTE: Before the first firing of the fireplace, the gas
supply line should be purged of any trapped air.
Maximum Inlet
Gas Pressure
14.0 inches
w.c.
14.0 inches
w.c.
NOTE: Consult local building codes to properly size
the gas supply line leading to the 1/2 inch
(13 mm) hook-up at the unit.
Manifold
Pressure
3.5 inches
w.c.
10.0 inches
w.c.
This gas fireplace is designed to accept a 1/2 inch
(13 mm) gas supply line.
A one-eighth (1/8) inch (3 mm) N.P.T. plugged tapping is
provided on the inlet and outlet side of the gas control for a
test gauge connection to measure the manifold pressure.
To install the gas supply line:
• A listed (and State of Massachusetts approved) 1/2 inch
(13mm) tee-handle manual shut-off valve and a listed
flexible gas connector are connected to the 1/2 inch
(13mm) inlet of the control valve. NOTE: If substituting
for these components, please consult local codes for
compliance.
The fireplace and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of the system at test pressures in
excess of one-half (1/2) psig (3.5 kPa).
• Locate the gas line access hole in the outer casing of
the fireplace.
The fireplace must be isolated from the gas supply piping
system by closing its individual shut-off valve during any
pressure testing of the gas supply piping system at test
pressures equal to or less than one-half (1/2) psig (3.5 kPa).
• The gas line may be run from either side of the fireplace
provided the hole in the outer wrap does not exceed 2” in
diameter and it does not penetrate the actual firebox.
• Open the fireplace lower grille, insert the gas supply line
through the gas line hole, and connect it to the shut-off
valve.
• When attaching the pipe, support the control so that the
lines are not bent or torn.
• After the gas line installation is complete, use a soap
solution to carefully check all gas connections for leaks.
WARNING: DO NOT USE AN OPEN FLAME
TO CHECK FOR GAS LEAKS.
!
• Insert insulation from the outside of the fireplace and
pack the insulation tightly to totally seal between the
pipe and the outer casing.
• At the gas line access hole the gap between the supply
piping and gas access hole can be plugged with non-
combustible insulation to prevent cold air infiltration.
USE A WRENCH ON
SHUT-OFF VALVE
WHEN TIGHTENING
GAS LINE.
MANUAL
SHUT-OFF
VALVE
FLEX CONNECTOR
GAS VALVE
GAS LINE
CONTROL VALVE
ACCESS
Figure 31. Gas Supply Line
34
Download from Www.Somanuals.com. All Manuals Search And Download.
BLACK S2
REMOTE SWITCH
PIGTAIL
3/16” PIGGYBACK CONNECTOR
ON
OFF
ON/OFF
SWITCH
WHITE T2
GAS VALUE
RED T1
THERMOPILE
THERMOCOUPLE
OPTIONAL WALL SWITCH,
THERMOSTAT OR REMOTE
BLACK S1
Figure 32. Standing Pilot Ignition Wiring Diagram
Step 8. Wiring the Fireplace
Optional Accessories
NOTE: Electrical wiring must be installed by a licensed
electrician.
Optional fan and remote control kits require that 110-120
VAC be wired to the factory installed junction box before
the fireplace is permanently installed.
CAUTION: DISCONNECT REMOTE CONTROLS IF AB-
SENT FOR EXTENDED TIME PERIODS. THIS WILL PRE-
VENT ACCIDENTAL FIREPLACE OPERATION.
Wall Switch
For Standing Pilot Ignition Wiring
Position the wall switch in the desired position on a wall.
Run a maximum of 25 feet (7.8 m) or less length of 18
A.W.G. minimum wire and connect it to the fireplace ON/
OFF switch pigtails.
Appliance Requirements
• This appliance DOES NOT require 110-120 VAC to operate.
CAUTION: LABEL ALL WIRES PRIOR TO DISCONNEC-
TION WHEN SERVICING CONTROLS. WIRING ERRORS
CAN CAUSE IMPROPERAND DANGEROUS OPERATION.
VERIFY PROPER OPERATION AFTER SERVICING.
WARNING: DO NOT CONNECT 110-120 VAC
TO THE GAS CONTROL VALVE OR WALL
SWITCH OR THE APPLIANCE WILL MALFUNC-
TION AND THE VALVE WILL BE DESTROYED.
!
VARIABLE SPEED CONTROL
NOTE: IF ANY OF THE ORIGINAL WIRE
AS SUPPLIED WITH THE APPLIANCE
MUST BE REPLACED, IT MUST BE
REPLACED WITH TYPE 105OC RATED WIRE.
BLK
BLK
JUNCTION BOX
BLK
BLOWER RECEPTACLE
BLK
BLK
BLK
BLK
WHT
GROUND
WHT
BLK
TEMPERATURE
SENSOR SWITCH
BLOWER
GRN
TEMPERATURE
SENSOR SWITCH
BLK
WHT
JUNCTION BOX
110-120 VAC
FAN
SPEED CONTROL
(RHEOSTAT)
Figure 33. Fan Wiring Diagram
35
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSFORMER
3 VAC
INTERMITTENT PILOT IGNITOR
IGNITION MODULE 3 VAC
JUNCTION BOX
120 VAC
I
JUNCTION BOX
120 VAC
REM
FAN
S
REM
FAN
ORG
WALL SWITCH
FAN OUTLET RECEPTACLE
(NO FAN OPTION)
BRN
BRN
WHT
GROUND TO
FIREPLACE
CHASSIS
PLUG-IN
3V TRANSFORMER
OPTIONAL
BATTERY BACKUP
GRN
OPTIONAL
REMOTE
LOW VOLTAGE
SEE NOTE 1
FLAME SPARKER/
SENSOR
IGNITION
MODULE
(3V)
OPTIONAL
BATTERY
BACK-UP
ON/OFF
WALL SWITCH
VALVE
VALVE
LOW VOLTAGE
SEE NOTE 1
GROUND
REMOTE
CONTROL
NEUTRAL
HOT
Figure 34. Intermittent Pilot Ignition (IPI) Wiring Diagram
For Intermittent Pilot Ignition (IPI) Wiring
Optional Accessories
Appliance Requirements
Optional fan and remote control kits require that 110-120
VAC be wired to the fireplace junction box.
This appliance requires that 110-120 VAC be wired to the
junction box. Maintain correct polarity when wiring the junc-
tion box.
Wall Switch
Operation using Battery Power
Position the wall switch in the desired position on a wall.
Run 16 A.W.G. minimum Romex wire a maximum of 25
feet and connect it to the fireplace ON/OFF switch pigtails.
This fireplace has an optional battery operation. The sys-
tem is fully functional with the use of two “D” size batteries
without ordinary 110-120 VAC power.
CAUTION: LABEL ALL WIRES PRIOR TO DISCONNEC-
TION WHEN SERVICING CONTROLS. WIRING ERRORS
CAN CAUSE IMPROPERAND DANGEROUS OPERATION.
VERIFY PROPER OPERATION AFTER SERVICING.
Wiring to the battery pack should be left disconnected in
order to conserve battery life. In the case of a loss of power,
simply connect red and black wire leads to activate battery
power (connect red to red, black to black). The fireplace
can be used as necessary. Once power (110 VAC) is re-
stored, disconnect red and black wire leads to extend bat-
tery life.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: IF JOINTS BETWEEN THE FINISHED WALLS
AND THE FIREPLACE SURROUND (TOP AND SIDES)
ARE SEALED, A 300° F. MINIMUM SEALANT MATE-
RIAL MUST BE USED. THESE JOINTS ARE NOT RE-
QUIRED TO BE SEALED. ONLY NON-COMBUSTIBLE
MATERIAL (USING 300° F. MINIMUM ADHESIVE, IF
NEEDED) CAN BE APPLIED AS FACING TO THE FIRE-
PLACE SURROUND. SEE THE DIAGRAM BELOW.
Step 9. Finishing
Figure 35 shows the minimum vertical and corresponding
maximum horizontal dimensions of fireplace mantels or other
combustible projections above the top front edge of the
fireplace. See Figures 4 and 5 for other fireplace clearances.
Only non-combustible materials may be used to cover the
black fireplace front.
NOTE: Sheetrock or other combustible material such
as wood can be placed on the top edge of the fire-
place. A 1/2-inch gap along the side must be main-
tained.
WARNING: WHEN FINISHING THE FIREPLACE,
NEVER OBSTRUCT OR MODIFY THE AIR IN-
LET/OUTLET GRILLES IN ANY MANNER.
!
ST-TRC
CEILING
TOP EDGE
SIDE EDGE
31”
12"
1/2"
1/2" GAP
PIER-TRC & CORNER-TRC
TOP EDGE
SIDE EDGE
TOP EDGE OF FIREPLACE
Figure 35.
Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles above Fireplace
1/2" GAP
Figure 36. Sealant Material
Hearth Extensions
A hearth extension may be desirable for aesthetic reasons.
However,ANSI or CAN/CGA testing standards do not require
hearth extensions for gas fireplace appliances.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing the Ember Material
Step 10. Installing Trim, Logs & Ember Material
Installing the Trim
Ember material is shipped with this gas fireplace. The bag
labeled Golden Ember (GE-93) is flame colorant material.
The bag labeled Glowing Ember (050-721) is standard glow-
ing ember material.
Combustible materials may be brought up to the specified
clearances on the side and top front edges of the fireplace,
but MUST NEVER overlap onto the front face. The joints
between the finished wall and the fireplace top and sides
can only be sealed with a 300° F. (149° C) minimum sealant.
To place the ember material:
•
Remove the wing nuts and glass clips or tension springs
around the glass door.
WARNING: WHEN FINISHING THE FIREPLACE,
NEVER OBSTRUCT OR MODIFY THE AIR INLET/
!
OUTLET GRILLES IN ANY MANNER.
•
•
Remove the glass door from the unit.
Install optional marble and brass trim surround kits as
desired. Marble, brass, brick, tile, or other non-combustible
materials can be used to cover up the gap between
combustible material (sheetrock or wood) and the fireplace.
Place dime size pieces of ember material about 1/2 inch
apart near port holes in burner top. Do NOT press em-
bers into burner ports. Cover the top of the burner with a
single layer of ember material. For best performance do
NOT place embers on the ports at the rear of the burner.
Do not obstruct or modify the air inlet/outlet grilles. When
overlapping on both sides, leave enough space so that the
bottom grille can be lowered and the trim door removed.
•
Save the remaining ember materials for use during fire-
place servicing. The bag of embers provided is sufficient
for 3 to 5 applications.
Positioning the Logs
If the gas logs have been factory installed they should not
need to be positioned. If the logs have been packaged
separately, refer to the instructions that accompany the
logs. Save the log instructions with this manual.
•
•
•
Replace the wing nut, glass clips, and screws.
Replace the glass door and a front trim door on the unit.
Hand tighten the wing nut.
If sooting occurs, the logs might need to be repositioned
slightly to avoid excessive flame impingement.
Shutter Settings
NG
LP
___________________________________________
PIER-TRC
1/2”
SET
___________________________________________
ST-TRC
1/2”
SET
___________________________________________
L&R CORNER-TRC
1/2”
SET
GLASS SPECIFICATIONS:
Large
Glass
Small
Glass
Glass
Type
Model
PIER-TRC
ST-TRC
CORNER-TRC’S
34” x 20”
34” x 20”
34” x 20”
20” x 20”
N/A
20” x 20”
TEMPERED
TEMPERED
TEMPERED
Figure 37. Placement of the Ember Material
Heat-N-Glo fireplaces manufactured with tempered glass may
be installed in hazardous locations such as bathtub enclo-
sures as defined by the CPSC. The tempered glass has
been tested and certified to the requirements ofANSI Z97.1-
1984 and CPSC 16 CFR 1202. (Safety Glazing Certification
Council SGCC # 1595 and 1597. Architectural Testing, Inc.
Reports 02-31919.01 and 02-31917.01.)
This statement is in compliance with CPSC 16 CFR Sec-
tion 1201.5 “Certification and labeling requirements” which
refers to 15 USC 2063 stating “…Such certificate shall ac-
company the product or shall otherwise be furnished to any
distributor or retailer to whom the product is delivered.”
Some local building codes require the use of tempered glass
with permanent marking in such locations. Glass meeting
this requirement is available from the factory. Please con-
tact your dealer or distributor to order.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 12. Lighting the Fireplace
Step 11. Before Lighting the Fireplace
You’ve reviewed all safety warnings, you’ve checked the
fireplace for gas leaks, you know the vent system is
unobstructed, and you’ve checked for faulty components.
Now you’re ready to light the fireplace.
Before lighting the fireplace, be sure to do the following:
Remove all paperwork from underneath the fireplace.
Review safety warnings and cautions
• Read the Safety and Warning Information section at
the beginning of this Installers Guide.
WARNING: PLEASE REFER TO THE USER’S
MANUAL FOR ALL CAUTIONS, SAFETY, AND
!
Double-check for gas leaks
• Before lighting the fireplace, double-check the unit for
possible gas leaks.
WARNING INFORMATION PERTAINING TO THE
LIGHTING AND OPERATION OF THE FIREPLACE.
Double-check vent terminations and front grilles for
obstructions.
After the Installation
• Before lighting the fireplace, double-check the unit for
possible obstructions that could be blocking the vent ter-
minations or the front grilles.
LEAVE THIS INSTALLATION MANUAL WITH
!
THE APPLIANCE FOR FUTURE REFERENCE.
Double-check for faulty components
• Any component that is found to be faulty MUST BE re-
placed with an approved component. Tampering with the
fireplace components is DANGEROUS and voids all war-
ranties.
A small amount of air will be in the gas supply lines. When
first lighting the fireplace, it will take a few minutes for the
lines to purge themselves of this air. Once the purging is
complete, the fireplace will light and will operate normally.
Subsequent lightings of the fireplace will not require this
purging of air from the gas supply lines, unless the gas
valve has been turned to the OFF position, in which
case the air would have to be purged.
NOTE: The fireplace should be run 3 to 4 hours on the initial
start-up. Turn it off and let it cool completely. Remove and
clean the glass. Replace the glass and run the fireplace for
an additional 8 hours. This will help to cure the chemicals
used in the paint and logs.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining and Servicing Your Fireplace
Fireplace Maintenance
Although the frequency of your fireplace servicing and main-
tenance will depend on use and the type of installation, you
should have a qualified service technician perform an appli-
ance check-up at the beginning of each heating season.
See the table below for specific guidelines regarding each
fireplace maintenance task.
IMPORTANT: TURN OFF THE GAS BEFORE SERVICING
YOUR FIREPLACE.
Replacing old ember material
Frequency: Once annually, during the checkup.
By: Qualified service technician.
MAKE SURE THE FLAMES
ARE STEADY—NOT
LIFTING OR FLOATING.
Task: Brush away loose ember material near the burner.
Replace old ember material with new dime-size and shape
pieces of Golden Ember (GE-93) and Glowing Ember (050-
721). New ember material should be placed alternately on
top of the burner - a layer of Golden Ember, a layer of
Glowing Ember, and so on. Save the remaining ember
material and repeat this procedure at your next servicing.
For more information, see Placing Ember Material.
Figure 38. Burner Flame Patterns
Checking Vent System
Frequency: Before initial use and at least annually
thereafter, more frequently if possible.
Cleaning Burner and Controls
Frequency: Once annually.
By: Qualified service technician.
Task: Brush or vacuum the control compartment, fireplace
logs and burner areas surrounding the logs.
By: Qualified service technician/Home owner.
Task: Inspect the external vent cap on a regular basis to
ensure that no debris is interfering with the flow of air. Inspect
entire vent system for proper function.
Cleaning Glass Door
Frequency: After the first 3 to 4 hours of use. As neces-
sary after initial cleaning.
u Cleaning Flame Sensor Rod (IPI Systems)
Frequency: Periodically.
By: Qualified service technician.
By: Home owner.
Task: Remove and clean glass after the first 3 to 4 hours of
use. After the initial cleaning, clean as necessary, particu-
larly after adding new ember (flame colorant) material. Film
deposits on the inside of the glass door should be cleaned
off using a household glass cleaner. NOTE: DO NOT handle
or attempt to clean the door when it is hot and DO
NOT use abrasive cleaners.
Task: Make a visual check of the straight flame sensor rod.
Use steel wool or fine sandpaper to carefully remove any
existing white deposits.
Checking Flame Patterns, Flame Height
Frequency: Periodically.
By: Qualified service technician/Home owner.
Task: Make a visual check of your fireplace’s flame patterns.
Make sure the flames are steady - not lifting or floating.
See Figure 38. The flame sensor (IPI) or thermopile/
thermocouple (standing pilot) tips should be covered with
flame. See Figure 30.
u
40
Download from Www.Somanuals.com. All Manuals Search And Download.
|