HARMAN
TLC 2000
OPERATOR'S
MANUAL
FOR USE IN THE U.S. AND CANADA
SAFETY NOTICE: IF THIS HARMAN TLC 2000 STOVE IS NOT PROPERLY INSTALLED, A
HOUSEFIRE MAY RESULT. FOR YOUR SAFETY, FOLLOW INSTALLATION DIRECTIONS.
CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTRESTRICTIONSAND INSTALLA-
TION INSPECTION REQUIREMENTS INYOUR AREA.
R6
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
3
WARNINGS
Carbon Monoxide (CO) Awareness
Carbon monoxide referred to as CO, is a color-
an alarm for fumes other than CO or CO from
sources other than the stove such as car or lawn
mower exhaust.
less, odorless gas that is produced during combustion
of coal and other fuels. CO fumes are toxic and can
be fatal.
If the alarm sounds
The TLC 2000 is a closed loop system specially
designed to prevent the escape of CO and other com-
bustion products from the stove.
Even though this stove is designed to be as safe
as possible, it is important that you install a CO de-
tector. This is true for oil, gas, or wood as well.
CO is heavier than air. This causes accumula-
tion to occur at the floor first. Therefore, it is best to
install the detector at table top level or lower rather
than on the ceiling like a smoke detector.
1. Increase ventilation by opening windows
or doors.
2. Make sure the stove doors and hopper lid
are closed and latched.
3. Check stove for electrical power and
normal operation.
4. Check for false alarm.
CO detectors are very sensitive and may sound
(Never sleep in the same room with any coal burning stove.)
Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to
start or “freshen up” a fire in this heater. Keep all such liquids well away from the heater while it is in use.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
4
Specifications - Harman TLC 2000
Weight
375 lbs
Flue Size
6 inch
Log Length Recommended
Heating Capacity
Blower Size (optional)
16" with 18" Max
1,900 sq. ft.
135 variable speed
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
5
Top Load Door
Clean-out Cover
TopLoad Opening
Top Load
Door Arm
Glass Door
Wood Air
Control
Grates
Side Shield
Coal Air Control
Removable
Shaker Handle
Front Load
Door Latch
Ash Door
Ash Door Latch
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
6
Operation
Fuels for USA
The Stove
Wood:
Doors
Wood may be burned in the TLC2000for the purpose of
igniting coal.
Wood may also be burned with theglass door open and
a screen in place to prevent sparks from escaping. This pro-
vides a real open fire atmosphere.
Your stove has a large glass-paneled door for loading
and fire viewing, a separate smaller door for removing
ashes and a top loading door. To open the glass door,
turn the handles clockwise and pull out; to close the door,
return the handles to an open 9 o'clock closed 6 o'clock,
and push in to engage the latch while turning the handles
counterclockwise. To open the ash door, lift up the handle
and pull out. Close the door by pushing in and pushing
the handle all the way down. To open the top load door
move the wooden knob located on the left side of the
stove front and upward until it locks the top open. Page 6.
If the latch in either of your TLC 2000 doors needs ad-
justment, follow the instructions given in the Maintenance sec-
tion.
Coal:
Anthracite coal, pea or nut size, is the primary fuel for
which the TLC2000 is designed. Bituminous coal may also be
burned butthe results will varydo to the variation in bituminus
coal from state to state.
Fuels for Canada
Wood:
All doors must be closed while the stove is in normal
operation, and the gaskets routinely examined for wear and
replaced when necessary. The glass door may be left open
and the opening covered with a screen when operating as a
Wood may be burned as a primary fuel. This is because
U.S. EPAregulations do not apply in Canada.
Wood may also be burned with the glass door open and
fireplace. Good door seals are important formaintaining con- a screen in place to prevent sparks from escaping.
trol of the stove. Operating the stove with the ash door open,
or with a door inadequately sealed, could create a serious
Anthracite coal, pea or nut size, may also be burned as a
overfiringcondition (discussed later in this section).
Coal:
primary fuel for the TLC2000. Bituminous coal may also be
burned butthe results will varydo to the variation in bituminus
NEVER OPERATE WITH MORE THAN ONE
coalfrom provinceto province.
DOOR OPEN AT A TIME
The glass used in your TLC 2000 is manufactured to
exact standards to withstand the high heat of the fire, but like
all glass, it must be treated with common sense and care.
Never abuse the glass by slamming the door shut or striking
the glass with a heavy object. If the glass is broken or dam-
aged, do not operate the stove until it has been replaced (See
instructions in the Maintenance section.)
Grates
The Harman TLC 2000’s unique grate system consists
of two Cast iron grates linked together to operate
simaltainiously when the external shaker handleis moved.
The purpose of the grate system is to to support the
coal bed while air flows up through the grates to the burning
coal. The grates are also used to remove ashes from the bot-
tom of the coal bed while the fire is burning. This is accom-
plished by shaking the shaker lever back and forth with short
choppystrokes. Thiscauses the ashes to fall through the grates
into the ash pan. It is the special design of the Harman Grates
that allows longerintervals between refueling and shaking the
grates.
Harman Grate System
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
7
Air Controls
Coal
The primary air control for coal burning is a knob
located on the bottom door. Sliding the knob to the left pro-
vides less air for a smaller fire. Sliding the knob to the right
provides more air for a larger fire.When burning wood this
knob should be all the way to the left, closed.
Wood
The primary air controls for wood burning are lo-
cated on each side as shown below and on page 4. Both con-
trols should be adjusted equally. Air from these controls also
provides a curtain of air across the glass to keep it clean.
Move the controls down for less heat and up for more heat.
When burning coal these controlsshould be in thedown posi-
tion. CAUTION: The wood controls are hot. Use the
removable shaker handle or gloves to adjust these con-
trols.
WOOD
WOOD
Coal must have air coming up through the coal bed in
order to burn. Some air over the top of the coal helps burn
gases. A small amount of air enters the top of the coal fire
when the wood controls are in the down position.
Wood burns with top or bottom air; however, top air
coming down across the glass to form an air curtain works
best and keeps the glass clean.
COAL
This is why it is recommended that the coal control be
positioned to the left for wood burning.
Building and
Maintaining a Wood Fire
Never use gasoline, gasoline-type lantern fuel,
kerosene, charcoallighter fluid, or similar liquids to start
or “freshen up” a fire in this heater. Keep all such
liquids well away from the heater while it is in use
.
Crumple up six to eight sheets of news paper and place
in the firebox. Next place pieces of dry wood 3/4 inch maxi-
mum diameter on top of the paper, Next place several 1 " - 2"
split pieces ofdry wood on top, followed by a few 2" -3" split
pieces. Set the wood air controls at the maximum heat output
setting, all the way up. Place the knob on the bottom door to
the left. These settings will allow the glass to stay clean as
you build your fire. The coal knob may be moved to the right
to speed the ignition process but the glass may get dirty.
Ignite the paper and allow the fire to burn until a good
charcoal bed, 2" - 3" (50 mm - 80 mm) is formed; (You may
need to leave the ash door open a crack to get the blaze going
properly, but never leave the stove unattended.) Add more
wood to create a deeper charcoal base 3" to 4".
Once the charcoal bed is established you may add a full
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
8
load of dry wood. After adding the fuel, leave air setting at
maximum for 5 to 15 minutes. Then adjust the air controls
and blower speed for the desired heat output.
Remove
Cleanout Plate
To Burn As A
Fireplace Stove
Reloading.
Once you have prepared and maintained a thick char-
coal bed, you should be able to reload the stove, allow some
burning at the maximumair setting, and reset the air control in
about five minutes.
Select hardwoods if possible, as they are heavier and
contain more heating capacity (BTU’s) per load than do soft-
woods. Wood should be splitand stored under coverfor “sea-
soning” - a year is recommended. Your stove is not an incin-
erator - do not burn garbage, painted or treated wood, plastic,
or other debris.
Keep the area around the stove free from clutter.
Keep allcombustibles, includingfuel, beyond the code-required
clearance distance (48" or 1215 mm in the U.S., 1525 mm or
60" in Canada). Never store fuel in front of the stove where
it could interfere with door operation, safe loading, and ash
removal.
Blower. To regulate the speed of the optional con-
vection blower, adjustthe controlfrom lowto high by turning
the knob located on the blower cord.
Removing Wood Ashes.
Alwayswear gloves to remove the ash pan Lift the latch
on the ash door and open. Pull the ash pan out by the handle.
Lift the handle to the vertical position to carry the ashes to a
disposal location. Close the ash door while you are disposing
of the ashes. The fire will get very hot if the bottom door is
left open even for a short period. Replace the ash pan. Re-
move ashes from thefire chamber periodically by shaking the
grates. Wood burns best with an ash bed under the wood;
therefore, do not shake all of the ashes down.
Never let the ashes build up to over 3" in depth. Exces-
sive ash buildup can prevent proper venting of exhaust gases.
Also do notoverfill the ash pan. Ash buildup between the ash
pan and the grates can cause them to overheat and wear out
prematurely.
Operating as a Fireplace.
The TLC 2000 is tested and approved to be burned with
the front load door open. In this mode of operation you get a
true fire sound as well as appearance. Due to the crackling
and popping of burning wood it is necessary to place the op-
tional screen over thedoor opening. This preventssparks from
entering the room just like a screen over a fireplace.
Theclean-out plate should be removed to burn as a fire-
place. This is done by lifting up on the tab on the front of the
plate.
To install the screen, open the glass door and place the
screen over the door opening. Push on the screen until the
two spring clips snap into place. To remove the screen, pull
on the gold handle.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
9
Building and
Maintaining a Coal Fire
Build a wood fire as described but instead of adding
larger wood, limit the size to about 2"in diameter.Add enough
2" wood that the firebox floor is covered with burning wood.
After the wood is burning well for about five minutes,
put the wood air controls in the down position and slide the
coal air control to the right. This makes the primary air flow
up through the grates as is required for coal burning.
Next add a layer of coal on top of the wood. Continue
burning until the layer of coal is turning red and igniting. It is
possible to speed this process by opening the ash door, but
never for more than five minutes at a time.
Add Even Layers by pouring evenly across coal bed
Operation with the ash door open for more than five
minute will overfire the stove and may cause damage to the
stove. Never let the stove unattended with the ash door open.
After the layer of coal is burning a second layer may be
added. After the second layer is burning more layers may be
added. Do not add coal above the firebricks or grate bars.
The stove is hot while in operation. Keep
children, clothing and furniture away. Contact
may cause skinburns.
As you begin to operate your stove at higher tem-
peratures, you will notice a “hot” or unpleasant smell; this is
just the paintgoing through the curing process, and will disap-
pear after a few fires.
Overfiring
6
Avoid overfiring your stove, a potentially hazardous
situation which can lead to overheating of combustible mate-
rials, damage to the stove, and in extreme cases, cause a fire.
Overfiring is caused by: 1. Too much air flowing through the
stovetoo quickly. 2. You may have positioned the primary air
control level too far to the right. 3. Inadvertently left the bot-
tom door open or 4. Not kept up with routine maintenance,
such as checking door gaskets for wear.
4
3
4
2
Overfiring results in excessive fuel consumption, and
may cause parts of the stove or chimney connector to glow
red. If you notice signs of overfiring, reduce the air supply to
the fire, and review the Maintenance section in this manual.
1
Never leave the stove unattended ifeither theash
or load door is open. Overfiring may result.
5
In the event of a chimney fire, call your local fire de-
partment; make sure everyone is safely out of the house.
Reduce the air intake of the stove as much as possible using
the air control lever. Do not throw water on the fire; this can
cause stove damage and create an even more dangerous situ-
ation. Have your chimney professionally cleaned and in-
spected before resumingburning in your stove.
1. Grates
6. Grate Bars
2. AshesOn Grates
3. Partly Burned Coal
4. Fresh Coal
5. Ashes In Ash Pan
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
10
Disposal of Ashes. The TLC 2000 was designed to
provide access to the ash pan without the need for opening
the main door. Wearing heavy protective gloves, open the
ash door and remove the ash pan by pulling it forward by
the handle. Close the ash door before taking the ashes
outside for safe disposal.
A good time to empty the ash pan is before loading.
This ensures that the ashes will be cold and safer to handle
than directly after shaking the ashes down or tending the
fire.
Ashes should be placed in a metal container with a
tight fitting lid. The closed container of ashes should be
placed on a noncombustible floor or on the ground, well
away from all combustible materials, pending final dis-
posal. If the ashes are disposed of by burial in soil or
otherwise locally dispersed, they should be retained in the
closed container until all cinders have thoroughly cooled.
Never use the ash disposal container for other trash.
Wood ash can be added to your garden or compost.
Handle
AshPan
Handle
Refueling
Open the coal air control to the maximum postion
by sliding it to the right. Allow the fire to burn vigorously
for several minutes. Shake the grates with short choppy
strokes until the first red coals fall into the ash pan, then
stop! Add coal to the top of the coal bed. It is good to let
an edge of red coal exposed to help ignite the gases comming
off of the coal. These gasses will produce a blue flame. The
coal air control may be returned to the desired setting.
Cooking Grill
Stainless Steel Cooking Grill (Optional )
The cooking grill can be used for open fire grilling over
anthracite coal or wood.
To install the grill place the handle in the grill as shown
at left. The grill can now be lifted and positioned in the open-
ing on top of the stove as shown below left.
Caution: Cooking Grill May Be Hot. Always wear
gloves when handling the grill.
Cooking on anthracite coal produces flavor similar to a
gas grill.
Cooking on wood producesmany flavorsdepending on
the type of wood used. More flavor is added when cooking is
done with the top closed. This causes the heat and smoke to
circle around the food.
As with any cooking, the amount of heat and length of
time it is cooked must be experimented with for best results.
TLC 2000 with cooking grill in action
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
11
Maintenance
The Fire Chamber
Like all fine equipment, your TLC 2000 re-
quires some routine maintenance and inspection.
Follow the guidelines in this section to guarantee
safe, efficient operation.
The inside of the fire chamber should be exam-
ined for damage to the firebrick lining material, and
grates. If any bricks have been damaged, replace them
with Harman Stove Company replacement parts.
Glass - Replacement
The Stove
If the stove’s glass is cracked or broken, you
must replace it before operating your stove. Remove
pieces carefully. Replace glass only with Harman Stove
Company replacement glass panels; do not use substi-
tutes.
To replace the glass panel(s), you will need to
remove thedoor. To do this, open the door, lift it straight
up and place it on a soft surface.
Surface
The stove’s exterior surface should be dusted
periodically with a softcloth. For morethorough clean-
ing, wait until the stove is cool before using a damp
cloth to clean any blemishes.
The Door
Thegold plated front doorshould never bebuffed
orpolished. Abrasive cleaners and metalpolishes will
remove the platingand thereforeshould neverbe used.
If the door needs to be cleaned, wait until the stove is
completely cool, then usea sponge, soap and water to
gently remove dirt and stains. Before relighting the
stove, remove all soap residue and wipe dry.
Carefully remove damaged glass, gasket material,
and hold down clips (set aside).
Referringto thediagram, notehow the various com-
ponents of the door system fit together. Lay the load
door face down on the soft surface, and install the self
adheasive 1/4"” gasket material around the front face of
the glass.
Set the glass pane and gasket gently onto the door.
Installthehold down clipsand tighten with boltsas shown.
Reinstall door on stove.
Controls
To avoid a rust build-up on the inner surfaces
of the controls, work the controls back and forth sev-
eraltimes, during the summer, or anyprolonged period
when you are not using your stove.
Glass -Cleaning
Sometime it will be necessary to clean accumu-
lated ash from the glass surface; allowing this ash to
remain on the glass for long periods can result in “etch-
ing” dueto the acidity ofthe ash.
The creosote which accumulates
Door
on the glassshould burn off dur-
ing your hot fires.
GlassGasket
Glass
Never clean the glass
while it is hot, and do not use
abrasive substances. Wash the
surface with cool water, and
rinse thoroughly. You may wish
to use a non-abrasive cleaner
specifically designed for use on
stove glass. In any case, dry
thoroughlybeforerelighting your
stove.
Hold Down Clips
and Bolts
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
12
Gaskets
Gaskets are used on the doors and top lid of the TLC
2000. You must check these gaskets from time to time, and
replace them when necessary. The gaskets are made of fi-
berglass of different sizes (obtainable from Harman Stove
Dealer) and are fixed in place with a high temperature stove
gasket cement. To change a gasket, first remove the worn
fiberglass and clean the area with a wire brush. Also clean
any other surfaces that come into contact with the gasket.
Place a small bead of cement in the area under the gasket,
then press new gasket material into the channel; do not over-
lap the ends. Seat the gasket firmly by applying pressure
when possible; for example, after changing the door gasket,
close the door. Allow the cement to dry before using your
stove.
Gaskets are located:
On the doors to provide airtight closure.
On the lid.
Handle
The handle on the front door of your TLC 2000 is
attached to threaded shafts. After a period of time, you may
find that the front door does not close as firmly as when your
stove was new. This is due to a natural compression of the
gaskets. To tighten the seal, open the door and rotate the
handle one full turn counterclockwise or bend the latch plate
on the stove.
Blower
The optional blower on your TLC 2000 stove re-
quires very little maintenance. You should, however, keep
the air inlet and the motor free of dust and dirt.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
13
Installation
DO NOT INSTALL IN A SLEEPING ROOM
Assembly
Blower (Optional )
Bolt the blower to the bottom rear of the stove with
four 1/4-20 bolts. Tighten the bolts, but do not overtighten.
The powercord for the blower must be connected to
a grounded outlet, and may not be routed above, under, over
or around the stove itself.
BlowerVariable
Speed knob
Top Air Grill
Top Air Grill (Optional )
The top air grill must be installed before the chimney
connector is installed.
To install simply place the top air grill over the flue out
let and position as shown at left. It is held in place by gravity.
The top air grill is a decorative option that does not add
or subtract from the performance of the stove.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
14
Parallel versusCorner Installations
Floor Protection
In all installations, the area under and around
Aparallel installation is one in which the back
and sides of the stove are parallel to the walls behind
and to the side of the stove. Acorner installation is one
in which the back of the stove is positioned diagonally
across a corner of the room. Each installation requires
its own set of clearances.
For parallel installations, the required clearance
distances from the stove are: 1) to the side wall, 18" ;
2) to the back wall, 16". From the chimney connector
to the wall, 18" and to the ceiling, 36". Fireplace instal-
lations must meet these same clearance requirements;
specifically follow these guidelines for mantel and trim
clearances.
For corner installations, the clearance distances
from the stove are 12" from each corner of the stove
measured straight to the nearest combustible material.
From the front of the stove, clearance to
combustible materials such as furniture, curtains,
fuel, etc., is: 48" in the U.S. and 60" in Canada.
the stove must be protected from falling ash and live
coals. The floor protector must be of noncombustible
material, and positioned as shown in the accompanying
illustration. The guidelines for floor protection are: 1)
completely under the stove and any horizontal runs of
connector;2) 2"(50mm) in back of the stove;3) 8"(200
mm) to each side; 4) U.S. 16"(405 mm) in front of the
doors; Canada 18" (450 mm) in front of the doors.
Clearances
Clearance is the empty space required between
the stove orchimney connector to the nearest combus-
tible surface or object, such as walls, ceilings, floors, or
furniture. Clearance distances may only be reduced by
using methods approved by either theCAN/CSA B365
standard (Canada) or NFPA 211 (U.S.) Contact your
building authority for information if you are interested
in reducing clearance distances other than those pre-
sented here.
Wall
Wall
12"
18"
16"
2"
18"
12"
8"
8"
16"
Floor Protector
Floor Protector
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
15
glowing red. Itis important that you follow thechimney guide-
lines in this manual, including size, type, and height to avoid
draft problems.
When installed and operated according to this manual,
the TLC 2000 will produce enough hot gases to keep the chim-
ney warm so that adequate draft is maintained throughout the
burn cycle.
The Chimney System
Creosote
When wood is burned slowly, it produces tar and
other organic vapors, as well as soot, which combine with
expelled moisture to form creosote . The creosote vapors
condense in therelatively cool chimney flue(associated with
a slow burning fire). As a result, creosote accumulates on
the flue lining. When ignited, this creosote can result in an
extremely hot fire.
Chimney Connectors
In general, following theseguidelines willensure com-
pliance with all national and provincial codes; prior to begin-
ning yourinstallation, check with yourlocal buildingcode offi-
cial to check on additional local regulations which may influ-
ence the design and placement of your venting system.
The Harman TLC 2000 may be installed with (150
mm) 24 gauge chimney connector pipe. Size of the connec-
tor should correspond to the size of the flue collar opening.
Do not use makeshift compromises. No part of the chimney
connector may pass through an attic or roof space, closet or
other concealed space, or through a floor or ceiling. When-
ever possible, avoid passing the connector through a combus-
tible wall; if you must, use an approved wall pass-through,
described later in this section.
Assemble the connector beginning at the flue collar,
with the crimped ends pointing towards the stove (to keep
debris and creosote flakes inside the system). Each joint,
including the one to the stove’s flue collar and the one to the
chimney itself should be secured with at least three sheet
metal screws. Screws may be a maximum of 3 inches apart.
A 1-1/4" (30 mm) overlap is required at each joint, including
the flue collar attachment. No more than two 90 degree el-
bows should be used, and the totallength ofconnector should
not exceed 10 feet (3 m). All horizontal runs of connector
must have a minimum upward slope of 1/4"(6 mm) per foot
(20 mm per meter).
The chimney should be inspected at least once every
two months during the heating season to see if any creosote
build-up has occurred. Checking your chimney and chimney
connector more frequently, especially while you are getting
used to your stove, is recommended. To inspect this system,
let the stove cool. Using a flashlight and mirror, check the
interior of the chimney connector, and the chimney itself. If a
significant layer of creosote or soot has accumulated (1/8"”
or 3 mm) it should beremoved to reduce the risk of a chimney
fire.
To clean deposits from the surface of the connector,
use a stiff wire brush after dismantling the connector assem-
bly. To clean the chimney, use a specially designed brush
sized to fit your particular flue opening, or call an established
chimney cleaning service.
At theend of the heating season, perform a thorough
examination of your chimney system, and have it repaired if
necessary.
Draft
Draft is widely misunderstood. It is important that
you, the stove operator, realize that draft is a variable effect,
not a given quantity. Stoves and chimneys do not have draft,
yet draft is the key to your stove’s performance.
Draft is a force, produced by an operating stove and
the chimney to which it is attached. It is created by hot gases
rising up the chimney, creating a pressure difference between
the inside of your home and the outside air. It continually
moves fresh combustion air into the stove, and hot exhaust
gases out of the stove; withoutthis constantflow, the fire will
go out.
Wall Pass-throughs
Occasionally it is necessary to pass the chimney con-
nector through a combustible wall to reach the chimney.
Other factors, such as barometric pressure, winds, Depending on your localbuilding codes, and thepertinent pro-
the airtightness of the home, the total inside chimney volume, vincial or national codes, there are several choices for ac-
chimney height and the presence of venting devices such as complishing this safely. Before beginning your installation,
exhaust fans also play a role in maintaining an adequate draft. contact local officials, and also the chimney connector and
Low barometric pressures, super insulated homes and ex- chimney manufacturer for specific requirements.
haust fans can reduce draft; winds can play havoc with draft;
Canada. Three methods are approved by the Cana-
and too large or too small a chimney volume can cause re- dian Standards Association. Thediagram shows one method
duced draft due to the excessive cooling or not enough room requiring an 18"(450 mm) air space between the connector
to
vent
exhaust
gases
quickly. and the wall. It allows use of one or two covers as described
Some signs of inadequate draft are smoking, odor, in the diagram. The two other methods are described in detail
difficulty in maintaining the fire, and low heat output. Over- in the current issue of CAN/CSA B365, the national stan-
draft can be caused by a very tall chimney even if it is the dard.
recommended size, and can cause overfiring of your stove.
United States In the U.S., the national code is NFPA
Signsof an overdraft include rapid fuelconsumption, inability 211. While many localities adopt this standard, be sure to
to slow the fire, and parts of the stove or chimney connector check with local authorities before beginningyour installation.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
16
The NFPA (National Fire Protection Association)
permitsfour methods for passingthrough acombustible wall.
A commonly used method to pass through awall directly to a
masonry chimneyis to clear a minimum 12"(300mm) around
the entire chimney connector, and fill it with brick masonry
which isat least 3.5"(90 mm)thick. Afireclay liner, minimum
3/8" (9 mm) wall thickness must run through the brick wall to
the chimney liner (but not beyond the inner surface of the
liner). It must be cemented in place with refractory cement.
This method is illustrated. For details on the other three op-
tions, refer to the most recent edition of the NFPA 211 code.
The Chimney
The TLC 2000 must be installed into a chimney ap-
proved for use with solid-fuel appliances. In the U.S., the
TLC 2000 must be connected to (1) a prefabricated chimney
complying with the requirements for Type HT chimneys in
the Standard for Chimneys, Factory-Built, Residential Type
and Building Heating Appliances, UL 103, or (2) a code-ap-
proved masonry chimney with a flue liner. In Canada, the
TLC 2000is listed for use with prefabricated chimneys tested
and listed to the high temperature (650 degrees C) chimney
standard, ULCS-629, orwith acode approved masonry chim-
ney.
Theminimum recommended height for any chimney
is 16 ft (4.8 m) above flue collar height. Around flue (either
masonry or approved prefabricated), of either 6" (150 mm),
7" (180 mm) or 8" (200 mm) may be used. For square or
rectangular masonry chimneys, nominalsizes of 8" x 8"or 8"x
12" (200 mm x 200 mm, 200 mm x 300 mm) may be used.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
17
Codes require that solid-fuel chimneys extend 3 ft
(0.9 m) above the point at which they exit from the roof,
provided that no part of any structure is within the top of
the chimney, then the chimney must extend 2 ft (6 m)
above the highest point with the 10 ft (3 m) radius top
height. If there is not ten feet of clearance from the top of
the chimney, then the chimney must extend 2 ft (6m)
above the highest point with the 10 ft (3m) radius.
Do not connect this unit to a chimney flue
servicing another appliance.
NOTE: The restriction of not venting more than
one appliance to the same flue applies to the U.S. specifi-
cally. While it is not recommended that you use the same
chimney for more than one appliance, in Canada certain
exceptions may be made. Be sure to contact your build-
ing code inspection official to see if this option is allowed
in your area, and to find out the specific requirements for
such an installation.
ExistingMasonry Chimneys
If you plan on using a pre-existing masonry chim- Venting toa Masonry Fireplace Chimney
ney, have it thoroughly inspected and cleaned. Any faults
In some situations, a code compliant chimney
which make the chimney unsafe and unusable must be originally used for a masonry fireplace may be used to
repaired prior to use. These can include improper height,
structural defects, blockages, inadequate clearance to com-
bustibles, unsealed openings into other rooms of the house,
signs of creosote or smoke leakage, a loose or absent clean-
out door, or absence of a liner.
install your TLC 2000. In addition to the requirements
found in the previous paragraphs, it is important to be
aware that all clearances must be met, including those
from the chimney connector to combustibles — 18" (360
mm) to sides and 18" (450 mm) to ceiling. Do not forget
to include floor protection in your plans. (See Clearances
and Floor Protection in this section.) Since many fire-
places have exposed wooden mantels and trim, pay spe-
cial attention to the clearances necessary to these materi-
als.
Do not connect to any air distribution
duct or system
Ventingto a Masonry Chimney
When connecting to a masonry chimney, several
provisions are standard. First, whether the chimney con-
nector is vented to the chimney through a thimble or a
breech pipe, neither must pass beyond the inner surface
of the chimney liner, and both must be firmly cemented
in place with refractory cement. (A thimble is a masonry
pipe which is inserted through the chimney wall, and is
frequently the preferred method; a breech pipe is a piece
of steel pipe used the same way.) In Canada, a breech
pipe has ridges or protrusions to lock it firmly into the
refractory cement. In either case, the chimney connector
vents to the chimney through the thimble or breech pipe.
Using a thimble, the connector slides completely
inside the masonry to the inner edge of the flue liner, and
may be easily removed for chimney and connector in-
spection. A breech pipe must extend at least 2" (50 mm)
into the room, so the connector can be attached with
sheetmetal screws.
If your fireplace chimney is behind a combustible
wall, you must use an approved wall pass-through sys-
tem to gain access to the masonry chimney. The chim-
ney connector must enter the chimney at a place where it
is lined, and the fireplace must be made inoperable. For
example, you might remove the damper, replacing it with
a secure, airtight, noncombustible seal (removable for in-
spection); this also satisfies the requirement that no room
air must be allowed to enter the chimney.
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
18
Installing to a Prefabricated Chimney
When venting your TLC 2000 using a prefabri-
cated chimney, be sure to contact local building code
authorities, and to follow the manufacturer’s instructions
exactly. Use only the manufacturer’s parts; do not use
makeshift installation techniques. All prefabricated
chimneys must be tested to either the U.S. or Canadian
high-temperature standards, UL 103 or ULC-629.
Warning: Do not install in sleeping room.
The Harman TLC 2000 was tested with fuel door
open and closed.
If you operate with doors open, open the by-pass
and put a screen over the opening.
Do not burn any fuel other than wood, such as
charcoal, which can cause increased carbon monoxide
production or overfiring. Never use highly volatile sub-
stances in your stove, such as gasoline, which could
cause an explosion.
When solid fuels are burned completely, they pro-
duce water and carbon dioxide. However, in long slow
burns, a substantial amount of carbon monoxide may
be produced. If allowed to build up, carbon monoxide
(which is odorless) can prove fatally poisonous. Proper
ventilation and draft will prevent this from happening.
If you smell smoke, turn up the air control lever setting,
and thoroughly ventilate your dwelling. During future
burns, be careful not to overload the stove with fuel, so
you will not be tempted to constantly operate at a low
air control setting.
Other causes of poor ventilation or draft are icing,
exhaust fans, a blocked outside air inlet, and room air
starvation. If your stove is sluggish and you get occa-
sional odor, check these possibilities and increase the
air flow in your home.
Caution: Always wear fire-resistant gloves to
operate the stove. The air control is hot while
in operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
TLC 2000 Parts List
1.
2.
3.
4.
5.
6.
7.
1-10-08074
2-00-852129
1-10-08127
1-00-08710
3-44-10050
2-00-852149
2-00-852153
TLC Rear Top
TLC Rear Hinge (2 per unit)
TLC Front Top Assembly
TLC-2000 Top Air Grill Assembly (Option)
1 1/2" Tadpole gasket
TLC Gasket Plate
TLC Cleanout
TLC Airwash Adjuster - Right
TLC Airwash Adjuster - Left
TLC Right Side Shield
8A. 2-00-852140-2
8B. 2-00-852140-1
9.
2-00-852141
10A. 2-00-852145
10B. 2-00-852144
11A. 1-10-08159A
11B. 1-10-05165
12. 3-43-4722386
13. 1-10-08690
14. 1-10-08718
15. 2-00-852132
16A. 2-00-852135
16B. 3-31-08739
17. 2-00-852133
18. 2-00-854148
19. 3-40-08746
20. 2-00-852136
21. 2-00-08725
22. 2-00-08726
23. 3-40-900450125
24. 2-00-852119
25. 3-00-00208
26. 1-00-08643
27. 1-10-852166
28. 2-00-852139
29. 1-10-852138
30. 2-00-852160
31. 3-40-05228
32. 1-10-08722
33. 2-00-852128
34. 2-00-852147
35. 3-31-08724
TLC Coal Bar (3 per unit)
TLC Coal Bar Holder (2 per unit)
TL Cast Load Door - Roped
TL Gold Load Door - Roped
TL Brass Ash Lip Trim
TLC Ash Pan Assembly
TLC Ash Door Assembly
TLC Bottom Slide Rail
TLC Airslide
5/16 - 18 x 2 1/2 All Thread
TLC Top Slide Tail
TLC Airslide Cover
TLC Airslide Knob
TLC Ash Door Latch
TLC Long Brick Support (2 per unit)
TLC Side Brick Support (2 per unit)
9 x 4 1/2 x 1 1/4 Firebrick (11 per unit)
TLC Grate Link
Long Grate Link (2 per unit)
TLC-2000 Blower Option
TLC Shaker Handle Weldment
TLC Left Side Shield
TLC Air Jacket Weldment
TLC Heat Shield
TL Wooden Knob
TLC Damper Linkage Arm Weldment
TLC Top Lift Arm With Notch
TLC Brick Backer (2 per unit)
1/4 & 3/8 Dowel Pin (2 per unit)
Download from Www.Somanuals.com. All Manuals Search And Download.
TLC 2000 Coal Stove
20
1
2
4
3
5
2
6
33
32
31
7
30
8A
9
29
11A
8B
10A
10B
11B
28
27
12
25
13
15
16A
24
16B
26
14
19
23
18
20
17
21
22
34. Brick Backers (2)
35. 1/4 & 1/8 Dowel Pins (2)
Download from Www.Somanuals.com. All Manuals Search And Download.
21
HARMANGOLD WARRANTY
6 YEAR TRANSFERABLE LIMITED WARRANTY
(Residential)
1YEAR LIMITEDWARRANTY (Commercial)
Harman Stove Company warrants its products to be free from defects in material or workmanship, in normal use and
service, for a period of 6 years from the date of sales invoice and for mechanical and electrical failures, in normal use and
service, for a period of 3 years from the date of sales invoice.
If defective in material or workmanship, during the warranty period, Harman Stove Company will, at its option, repair or
replace the product as described below.
The warranty above constitutes the entire warranty with respect to Harman Stove Company products. HARMAN STOVE
COMPANY MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING “ANY” WARRANTY OF
MERCHANTABILITY, OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. No employee, agent, dealer, or
other person is authorized to give any warranty on behalf of Harman Stove Company. This warranty does not apply if the
product has been altered in any way after leaving the factory. Harman Stove Company and its agents assume no liability for
“resultant damages of any kind” arising from the use of its products. In addition, the manufacturer and its warranty administra-
tor shall be held free and harmless from liability from damage to property related to the operation, proper or improper, of the
equipment.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
THESE WARRANTIES APPLY only if the device is installed and operated as recommended in the user’s manual.
THESE WARRANTIES WILL NOT APPLY if abuse, accident, improper installation, negligence, or use beyond rated
capacity causes damage.
HOW TO MAKE A CLAIM - Any claim under this warranty should be made to the dealer from whom this appliance was
purchased. Then contact is made with manufacturer, giving the model and serial numbers, the date of purchase, your dealer’s
name and address, plus a simple explanation of the nature of the defect. Extra costs such as mileage and overtime are not
covered. Nuisance calls are not covered by these warranties.
THIS WARRANTY IS LIMITED TO DEFECTIVE PARTS - REPAIR AND/OR REPLACEMENT AT
HARMAN STOVE COMPANY’S OPTION AND EXCLUDES ANY INCIDENTAL AND CONSEQUENTIAL
DAMAGES CONNECTED THEREWITH.
WARRANTY EXCLUSIONS: Failure due, but not limited to, fire, lightning, acts of God, power failures and/or surges,
rust, corrosion and venting problems are not covered. Damage and/or repairs including but not limited to; remote controls,
filters, fuses, knobs, glass, ceramic brick panels, ceramic fiber afterburners, door packing, tile, ceramic log sets, paint, batteries
or battery back-up and related duct work are not covered. Also excluded from this warranty are consumable or normal wear
items including but not limited to; flame guides, grates, coal bars, afterburner hoods, fire brick, gaskets. Additional or unusual
utility bills incurred due to any malfunction or defect inequipment and the labor cost of gaining access to or removal of a unit that
requires special tools or equipment are not covered. Maintenance needed to keep the stove in “good operating condition” is not
covered. This includes, but is not limited to, cleaning, adjustment of customer controls and customer education. Labor,
materials, expenses and/or equipment needed to comply with law and/or regulations set forth by any governmental agencies are
not covered.
This Warranty provides specific legal rights and the consumer may have other rights that vary from state to state.
In the event of change in ownership, the remaining portion of this warranty may be transferred to the new owner by
sending the new owner information to the Harman Stove Company.
PLEASE READ THE LITERATURE BY THE MANUFACTURER FOR THE VARIOUS ACCESSORY DEVICES.
THE MANUFACTURER WARRANTS THESE ACCESSORY DEVICES, NOT HARMAN STOVE COMPANY OR THEIR
WARRANTY ADMINISTRATOR. FURTHERMORE, THESE ACCESSORY DEVICES MUST BE INSTALLED AND
USED ACCORDING TO THE RECOMMENDATIONS OF THE MANUFACTURER.
REMEDIES - The remedies set forth herein are exclusive and the liability of seller with respect to any contract or sale or
anything done in connection therewith, whether in Contract, in tort, under any warranty, or otherwise, shall not, except as herein
expressly provided, exceed the price of the equipment or part of which such liability is based.
CLARIFY - The above represents the complete warranty, which is given in connection with stoves, manufactured by
Harman Stove Company. No other commitments, verbal or otherwise, shall apply except by a written addendum to this
warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
|