heaVY dutY
French FrY
cutter
66473
InstructIons and precautIons
saVe these InstructIons. read all
precautIons and InstructIons.
©
®
Copyright 2009 by Harbor Freight Tools . All rights reserved. No portion of this document or any artwork contained
herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams
within this document may not be drawn proportionally. Due to continuing improvements, actual product may differ
slightly from the product described herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
missing or broken, please call Harbor Freight Tools
at the number shown on the cover of this document
as soon as possible.
specIFIcatIons
Two sizes of Cutters and Pushing Blocks are
included in this set. This tool may be wall or table
top mounted. This tool may be disassembled for
Important saFetY
cleaning.
Cutter Frame Size: 4-5/8”W x 4-5/8”H x 11/16”T
InFormatIon
1.
2.
3.
4.
This is a cutting device. Do not place hand
near Pushing Block and Cutter.
Do not hold vegetable or any object in place
during cutting operation.
To prevent pinch injury, keep hands clear of
Lever (1) and Push Rods (9) at all times.
Assemble and use according to these
instructions only. Improper assembly or use
can create hazards.
5.
Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.
6.
7.
Keep assembly and use area clean and well lit.
unpackIng
When unpacking, check to make sure that
the item is intact and undamaged. If any parts are
Keep bystanders out of the area during
assembly and use.
Revised Manual 09j
Download from Www.Somanuals.com. All Manuals Search And Download.
Block and Cutting Frame will damage the
tool.
operatIon
1.
2.
Pull the Lever (1) back, which will pull the
Push Block back from the Cutting Frame.
Place a bowl beneath the End Support (2)
to catch the cut french fries as they are
produced.
3.
4.
Place the potato or vegetable to be cut in the
Food Tray (6). Align the vegetable roughly
with the center of the Cutting Frame.
Press the Lever (1) forward. The Push Block
will press the vegetable through the Cutting
Frame. Stop pressing the Lever forward once
the vegetable has been cut.
Push Block Latches
4.
To remove the Cutting Frame (10 or 12),
remove the four wing nuts holding it in place.
WARNING: Handle the Cutting Frame by the
outer edge only. The blades are sharp and
can cause injury if handled. The blades are
not removable from the Cutting Frame.
cleanIng
1.
Remove both the Cutting Frame (10 or 12)
and Push Block (11 or 13).
2.
3.
Lift Food Tray (6) out of tool.
5.
6.
To replace the Push Block, place it against
Block Plate A (4) with hooks protruding
through holes in Block Plate A. Then fix it in
place with the two swivel latches.
Wash Cutting Frame, Push Block and Food
Tray in dishwasher, or by hand using hot
water and detergent.
4.
Wipe off the rest of the tool using a clean
damp cloth with light detergent. Wipe it dry
after cleaning.
To replace the Cutting Frame, position it on
the end of the End Support (2) and attach it
with the Wing Nuts.
Wing Nut (19)
Wing Nuts(15)
note: Always use the Push Blocks and Cutting
Frames in matched pairs. Using mismatched
SKU 66473
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
1
record serial number here:
8
11
note:If product has no serial number, record
16
month and year of purchase instead.
5
note:Some parts are listed and shown for
illustration purposes only, and are not
available individually as replacement parts.
7
4
9
10
3
2
19
6
18
17
15
parts lIst & assemBlY
dIagram
part
description
Qty.
1
Lever
1
2
End Support (Stand A)
Lever Support (Stand B)
Block Plate A
1
3
1
please read the FolloWIng
4
1
careFullY
5
Block Plate B
1
THE MANUFACTURER AND/oR DISTRIBUToR HAS
PRoVIDED THE PARTS LIST AND ASSEMBLy DIAGRAM IN
THIS DoCUMENT AS A REFERENCE TooL oNLy. NEITHER
THE MANUFACTURER oR DISTRIBUToR MAKES ANy
REPRESENTATIoN oR WARRANTy oF ANy KIND To THE
BUyER THAT HE oR SHE IS qUALIFIED To MAKE ANy
REPAIRS To THE PRoDUCT, oR THAT HE oR SHE IS
qUALIFIED To REPLACE ANy PARTS oF THE PRoDUCT.
IN FACT, THE MANUFACTURER AND/oR DISTRIBUToR
ExPRESSLy STATES THAT ALL REPAIRS AND PARTS
REPLACEMENTS SHoULD BE UNDERTAKEN By CERTIFIED
AND LICENSED TECHNICIANS, AND NoT By THE BUyER.
THE BUyER ASSUMES ALL RISK AND LIABILITy ARISING
oUT oF HIS oR HER REPAIRS To THE oRIGINAL PRoDUCT
oR REPLACEMENT PARTS THERETo, oR ARISING oUT
oF HIS oR HER INSTALLATIoN oF REPLACEMENT PARTS
THERETo.
6
Food Tray
1
7
Support Rods with Wing Nuts
D12 x L27.4 cm
3
8
Lever Rods D7 x L37 cm
Push Rods D7 x L22 cm
Cutting Frame 64 Holes
Push Block 64 Holes
2
2
1
1
1
1
3
1
1
1
1
9
10
11
12
13
15
16
17
18
19
Cutting Frame 36 Holes(not shown)
Push Block 36 Holes(not shown)
Wing Nuts 5/16”
Cutting Frame Bolt
Axle Bolt and Nut set
Push Rod Bolt and Nut set
Wing Nut M5
REV 09c, 09h, 09j
SKU 66473
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
|