Magnetic tow light kit
Model 96933
Set up and operating inStructionS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SaVe thiS Manual.
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
4.
thoroughly test vehicle lights and tow lights before use.
Mount lights in proper orientation. Amber lights must face forward and red lights
must face backward. Improper orientation can confuse or distract drivers, caus-
ing a traffic hazard.
5.
Install on a 12 V negative ground circuit only. Installing on different circuit can
result in electric shock, fire, or property damage.
6.
7.
8.
Turn off vehicle and set the parking brake before installation or use.
Do not use on marine trailers (such as boat trailers). Not waterproof.
Wear ANSI-approved impact safety goggles and heavy-duty work gloves during
installation and use.
9.
Do not modify the Towing Light Kit and do not use the Towing Light Kit for a
purpose for which it was not intended.
10.
11.
Inspect before use; do not use if parts loose or damaged. Inspect wires and
connections for insulation damage or loose wires and repair before use.
People with pacemakers should consult their physician(s) before use. Electro-
magnetic fields in close proximity to heart pacemaker could cause pacemaker
interference or pacemaker failure.
12.
13.
This product is not a toy. Keep it out of reach of children.
Check light position and function regularly when towing, especially on rough or
uneven surfaces, or in windy conditions. The magnets may loose their grip on
the vehicle under extreme circumstances.
14.
15.
Remove conductive articles (such as metal jewelry, watches, and other items)
before installing light kit. Conductive objects can cause an electrical short re-
sulting in fire, property damage, or personal injury.
The warnings, precautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
SaVe theSe inStructionS.
unpacking
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
SKU 96933
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SpeciFicationS
Electrical Requirements 12 V / 4.3 A
Bulb Type
Connector
12 V / 21/5 W
4-way Flat
wiring
note: Some towing vehicles may already have a 4-way Flat Connector, “Trunk” plug
wired in. For those vehicles, skip the following wiring instructions.
if you do not have experience
doing this type of automotive
electrical wiring or if the
wiring in your vehicle differs
from that explained below,
have an automotive service
technician connect the wiring.
wiring color code
note: This is the wiring configuration of the
“Trunk” 4-way Flat Connector (23). The
towing vehicle may have a different wir-
ing color code.
“trunk” 4-way Flat
connector (23)
white
Ground
1.
Identify the towing vehicle’s wires
in the trunk that correspond to
the circuits indicated in the Wiring
Color Code diagram to the right.
The white ground wire from the
Pigtail (22) may be connected to a
bolt or appropriate component on
the vehicle to establish a ground
instead of a ground wire.
Brown
Running Lights
Yellow
Left Stop and
Turn Lights
green
Right Stop and
Turn Lights
wiring
pigtail (22)
2.
Connect the wires from the Wiring Pigtail (22) to the proper vehicle circuit wires
using Wire Splices (21). No stripping or cutting is usually required to connect
wires using the included Splices. Follow these three steps and refer to the
illustration to the right:
wire Splice (21) usage
a. Insert the end of the Pigtail (22)
wire into the ‘dead-end’ channel
of the Splice. Insert the wire all
the way to the end of the chan-
nel as shown.
a) insert pigtail (22) wire
into ‘dead-end’ channel
c) close Splice
cover securely
b. Place the Splice around the
correct vehicle circuit wire.
c. Make sure both wires stay
properly in place while the
cover is closed until it snaps
together.
3.
Verify that all wires are held se-
curely.
B) place splice around
vehicle wire
SKU 96933
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
5.
Plug the “Trunk” Connector (23) into the “Trailer” Connector (18).
warning! if the wire Splices (21) are used improperly and damage
the vehicle’s wiring, the vehicles rear lights may fail, resulting in a traffic
hazard. have an assistant operate the vehicle’s lights while you carefully
check that the vehicle lights and the towing lights all work properly after
installation. If any function of the vehicle or towing lights does not work, do
not drive the vehicle. Carefully inspect the splice connection and the circuit that
failed and repair the problem and retest before use.
6.
Disconnect the “Trailer” Connector (18) if the light kit is not going to be used yet.
Set up
1.
2.
To help avoid scratches, clean the mounting locations and clean the protective
labels under the lights.
Set the lights on the back of the vehicle being towed so that the RED side of
each light faces backwards. Set the light that has a green wire on the right side
and the light that does not have a green wire on the left side.
3.
Make sure all wires are secured with enough slack to prevent binding when turn-
ing, but controlled enough to prevent roadway or moving part contact.
3.
4.
Plug the “Trunk” Connector into the “Trailer” Connector.
warning! have an assistant operate the vehicle’s lights while you
carefully check that the vehicle lights and the towing lights all work prop-
erly.
• Both tow lights should illuminate when the towing vehicle’s running lights are
switched on.
• The tow lights should both light brightly as you apply the brake.
• The tow light with a green wire should blink brightly with the right turn signal.
• The tow light without a green wire should blink brightly with the left turn signal.
if anY function of the vehicle lights or towing lights does not work, do not
drive the towing vehicle until all lights are repaired and retested success-
fully.
5.
6.
The tow light kit is now ready for use. It will automatically illuminate when turn
and brake signals in the towing vehicle are used.
warning! check light position and function regularly when towing,
especially on rough or uneven surfaces. The magnets cannot hold the lights
to the vehicle in extreme circumstances.
7.
After towing, disconnect “Trailer” Connector, remove tow lights from towed ve-
hicle, clean with a moist cloth, and store in dry location out of reach of children.
SKU 96933
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
BulB replaceMent
wear anSi-approved safety goggles and heavy-duty work
gloves when replacing the bulb.
caution
1.
2.
Make sure the burned-out bulb has cooled completely.
Gently pry off a lens covering the burned out bulb using plastic pry tools (not
included) to prevent damage.
3.
4.
5.
6.
Press the burned-out bulb into the socket slightly and rotate it counterclockwise
to release it. Remove the burned-out bulb.
Insert a new 12V/21/5W bulb into the socket and secure it by turning clockwise
while pushing it into the socket.
note: The bulb has offset pins that allow it to be installed only one way. If it
does not properly and easily fit into place, then turn it around.
Gently snap the lens back in place, and test the lights to ensure proper opera-
tion before use.
partS liSt
part
1
2
description
Amber Front Lens
Red Rear Lens
Bracket
Q’ty
2
2
part
description
Q’ty
2
2
13 Cover
14 Magnet
15 Nut
3
2
2
4
Bulb
2
16 Screw
8
5
Socket
2
17 Power Cord
1
6
7
8
9
Threaded Shaft
Shell
Spring Washer
Flat Washer
2
2
2
2
18 “Trailer” 4-way Flat Connector
19 Left-Right Cord
20 Bulb Wire
1
1
4
4
21 Wire Splices
10 Ground Terminal
11 Nut
12 Screw
2
2
2
22 Wiring Pigtail
23 “Trunk” 4-way Flat Connector
24 Protective Label
1
1
2
note: Parts 21-23 not shown on diagram.
record product’s Serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 96933
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
aSSeMBlY diagraM
SKU 96933
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
liMited 90 daY warrantY
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser that this
product is free from defects in materials and workmanship for the period of 90 days
from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside
our facilities, criminal activity, improper installation, normal wear and tear, or to lack of
maintenance. We shall in no event be liable for death, injuries to persons or property,
or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or con-
sequential damages, so the above limitation of exclusion may not apply to you. THIS
WARRANTy IS ExPRESSLy IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITy AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection verifies the defect, we
will either repair or replace the product at our election or we may elect to refund the
purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that
the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission oaks Blvd. • Po Box 6009 • camarillo, cA 93011 • (800) 444-3353
pleaSe read the Following careFullY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND
ASSEMBLy DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy
OF ANy KIND TO THE BUyER THAT HE OR SHE IS qUALIFIED TO MAKE ANy REPAIRS
TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANy PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLy
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
By CERTIFIED AND LICENSED TECHNICIANS, AND NOT By THE BUyER. THE BUyER
ASSUMES ALL RISK AND LIABILITy ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR
HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 96933
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|