HP ProLiant DL385 G7 Server
Maintenance and Service Guide
Abstract
This guide describes identification and maintenance procedures, diagnostic tools, specifications and requirements for hardware components and
software. This guide is for an experienced service technician. HP assumes you are qualified in the servicing of computer equipment, trained in
recognizing hazards in products, and are familiar with weight and stability precautions.
Part Number: 588707-004
November 2011
Edition: 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Customer self repair...................................................................................................................... 6
Parts only warranty service............................................................................................................................6
Mechanical components .............................................................................................................................17
System components ....................................................................................................................................20
Removal and replacement procedures........................................................................................... 26
Required tools............................................................................................................................................26
Safety considerations..................................................................................................................................26
Preventing electrostatic discharge ......................................................................................................26
Server warnings and cautions............................................................................................................26
Preparation procedures...............................................................................................................................27
Power down the server .....................................................................................................................27
Extend the server from the rack..........................................................................................................28
Remove the server from the rack ........................................................................................................28
Access the product rear panel ...........................................................................................................29
SAS hard drive blank .................................................................................................................................30
Hot-plug SAS hard drive .............................................................................................................................31
Power supply blank....................................................................................................................................31
Hot-plug power supply................................................................................................................................32
Front right bezel.........................................................................................................................................33
Access panel .............................................................................................................................................34
Optical drive .............................................................................................................................................34
Optical drive cage.....................................................................................................................................35
Hot-plug fan...............................................................................................................................................36
Power supply backplane.............................................................................................................................38
SFF hard drive backplane ...........................................................................................................................39
SFF hard drive cage...................................................................................................................................40
LFF hard drive backplane............................................................................................................................41
LFF hard drive cage....................................................................................................................................42
Full-length expansion board shipping bracket................................................................................................43
PCI riser cage............................................................................................................................................44
Expansion slot covers .................................................................................................................................45
Expansion boards ......................................................................................................................................47
Half-length expansion board .............................................................................................................47
Full-length expansion board...............................................................................................................48
Air baffle...................................................................................................................................................49
Battery-backed write cache procedures.........................................................................................................49
Removing the cache module..............................................................................................................50
Removing the battery pack................................................................................................................50
Recovering data from the battery-backed write cache ..........................................................................51
Flash-backed write cache procedures ...........................................................................................................52
Flash-backed write cache module.......................................................................................................52
Flash-backed write cache capacitor pack............................................................................................53
Fan cage...................................................................................................................................................54
Heatsink....................................................................................................................................................55
Contents
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Processor...................................................................................................................................................57
Memory configurations...............................................................................................................................62
Advanced ECC memory....................................................................................................................62
Population order ..............................................................................................................................62
Population rules ...............................................................................................................................63
Population guidelines........................................................................................................................63
Memory bus speed...........................................................................................................................64
DIMMs............................................................................................................................................65
Battery replacement....................................................................................................................................65
Systems Insight Display...............................................................................................................................66
Front left bezel...........................................................................................................................................67
Power supply cage assembly.......................................................................................................................68
System board ............................................................................................................................................69
HP Trusted Platform Module.........................................................................................................................76
Cabling..................................................................................................................................... 77
SAS hard drive cabling...............................................................................................................................77
BBWC battery cabling................................................................................................................................78
FBWC capacitor pack cabling.....................................................................................................................78
Diagnostic tools.......................................................................................................................... 79
Troubleshooting resources...........................................................................................................................79
HP Insight Diagnostics ................................................................................................................................79
HP Insight Diagnostics survey functionality ....................................................................................................79
Integrated Management Log........................................................................................................................80
HP Insight Remote Support software .............................................................................................................80
USB support ..............................................................................................................................................81
Component identification............................................................................................................. 82
Front panel components..............................................................................................................................82
Front panel LEDs and buttons.......................................................................................................................82
Rear panel components ..............................................................................................................................83
Rear panel LEDs and buttons .......................................................................................................................84
System board components ..........................................................................................................................85
System board switches......................................................................................................................86
NMI functionality .............................................................................................................................86
DIMM slots......................................................................................................................................87
Systems Insight Display LEDs .......................................................................................................................88
Systems Insight Display LEDs and health LED combinations.............................................................................88
Hard drive numbering ................................................................................................................................89
SAS and SATA hard drive LEDs...................................................................................................................90
SAS and SATA hard drive LED combinations ................................................................................................90
PCI riser cage LEDs ....................................................................................................................................91
Non-hot-plug PCI riser board slot definitions..................................................................................................92
Battery pack LEDs.......................................................................................................................................93
FBWC module LEDs....................................................................................................................................94
Hot-plug fans .............................................................................................................................................95
Specifications............................................................................................................................. 96
Environmental specifications........................................................................................................................96
Server specifications...................................................................................................................................96
Power supply specifications.........................................................................................................................97
Hot-plug power supply calculations..............................................................................................................99
CD-ROM drive specifications.......................................................................................................................99
DVD-ROM drive specifications...................................................................................................................100
Contents
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAS and SATA hard drive specifications ....................................................................................................100
Contents
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer self repair
HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow for
greater flexibility in performing defective parts replacement. If during the diagnosis period HP (or HP service
providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will
ship that part directly to you for replacement. There are two categories of CSR parts:
•
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts,
you will be charged for the travel and labor costs of this service.
•
Optional—Parts for which customer self repair is optional. These parts are also designed for customer
self repair. If, however, you require that HP replace them for you, there may or may not be additional
charges, depending on the type of warranty service designated for your product.
NOTE: Some HP parts are not designed for customer self repair. In order to satisfy the customer warranty,
HP requires that an authorized service provider replace the part. These parts are identified as "No" in the
Illustrated Parts Catalog.
Based on availability and where geography permits, CSR parts will be shipped for next business day
delivery. Same day or four-hour delivery may be offered at an additional charge where geography permits.
If assistance is required, you can call the HP Technical Support Center and a technician will help you over the
telephone. HP specifies in the materials shipped with a replacement CSR part whether a defective part must
be returned to HP. In cases where it is required to return the defective part to HP, you must ship the defective
part back to HP within a defined period of time, normally five (5) business days. The defective part must be
returned with the associated documentation in the provided shipping material. Failure to return the defective
part may result in HP billing you for the replacement. With a customer self repair, HP will pay all shipping
and part return costs and determine the courier/carrier to be used.
For more information about HP's Customer Self Repair program, contact your local service provider. For the
Parts only warranty service
Your HP Limited Warranty may include a parts only warranty service. Under the terms of parts only warranty
service, HP will provide replacement parts free of charge.
For parts only warranty service, CSR part replacement is mandatory. If you request HP to replace these parts,
you will be charged for the travel and labor costs of this service.
Réparation par le client (CSR)
Les produits HP comportent de nombreuses pièces CSR (Customer Self Repair = réparation par le client) afin
de minimiser les délais de réparation et faciliter le remplacement des pièces défectueuses. Si pendant la
période de diagnostic, HP (ou ses partenaires ou mainteneurs agréés) détermine que la réparation peut être
effectuée à l'aide d'une pièce CSR, HP vous l'envoie directement. Il existe deux catégories de pièces CSR:
Customer self repair
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Obligatoire - Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de
remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
Facultatif - Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également
conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous demandez à HP de
remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le type de garantie applicable à
votre produit.
REMARQUE: Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la
réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit effectué
par un Mainteneur Agréé. Ces pièces sont identifiées par la mention "Non" dans le Catalogue illustré.
Les pièces CSR sont livrées le jour ouvré suivant, dans la limite des stocks disponibles et selon votre situation
géographique. Si votre situation géographique le permet et que vous demandez une livraison le jour même
ou dans les 4 heures, celle-ci vous sera facturée. Pour bénéficier d'une assistance téléphonique, appelez le
Centre d'assistance technique HP. Dans les documents envoyés avec la pièce de rechange CSR, HP précise
s'il est nécessaire de lui retourner la pièce défectueuse. Si c'est le cas, vous devez le faire dans le délai
indiqué, généralement cinq (5) jours ouvrés. La pièce et sa documentation doivent être retournées dans
l'emballage fourni. Si vous ne retournez pas la pièce défectueuse, HP se réserve le droit de vous facturer les
coûts de remplacement. Dans le cas d'une pièce CSR, HP supporte l'ensemble des frais d'expédition et de
retour, et détermine la société de courses ou le transporteur à utiliser.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus
d'informations sur ce programme en Amérique du Nord, consultez le site Web HP
Service de garantie "pièces seules"
Votre garantie limitée HP peut inclure un service de garantie "pièces seules". Dans ce cas, les pièces de
rechange fournies par HP ne sont pas facturées.
Dans le cadre de ce service, la réparation des pièces CSR par le client est obligatoire. Si vous demandez à
HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
Riparazione da parte del cliente
Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti
difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente
dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di servizi o di assistenza
HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo spedirà direttamente al cliente per
la sostituzione. Vi sono due categorie di parti CSR:
Obbligatorie – Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne affida la
riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il servizio.
Opzionali – Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di componenti
progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP, potrebbe dover sostenere
spese addizionali a seconda del tipo di garanzia previsto per il prodotto.
NOTA: alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per rispettare la
garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato. Tali parti sono
identificate da un "No" nel Catalogo illustrato dei componenti.
Customer self repair
7
Download from Www.Somanuals.com. All Manuals Search And Download.
In base alla disponibilità e alla località geografica, le parti CSR vengono spedite con consegna entro il
giorno lavorativo seguente. La consegna nel giorno stesso o entro quattro ore è offerta con un supplemento
di costo solo in alcune zone. In caso di necessità si può richiedere l'assistenza telefonica di un addetto del
centro di supporto tecnico HP. Nel materiale fornito con una parte di ricambio CSR, HP specifica se il cliente
deve restituire dei componenti. Qualora sia richiesta la resa ad HP del componente difettoso, lo si deve
spedire ad HP entro un determinato periodo di tempo, generalmente cinque (5) giorni lavorativi. Il
componente difettoso deve essere restituito con la documentazione associata nell'imballo di spedizione
fornito. La mancata restituzione del componente può comportare la fatturazione del ricambio da parte di HP.
Nel caso di riparazione da parte del cliente, HP sostiene tutte le spese di spedizione e resa e sceglie il
corriere/vettore da utilizzare.
Per ulteriori informazioni sul programma CSR di HP contattare il centro di assistenza di zona. Per il
Servizio di garanzia per i soli componenti
La garanzia limitata HP può includere un servizio di garanzia per i soli componenti. Nei termini di garanzia
del servizio per i soli componenti, HP fornirà gratuitamente le parti di ricambio.
Per il servizio di garanzia per i soli componenti è obbligatoria la formula CSR che prevede la riparazione da
parte del cliente. Se il cliente invece richiede la sostituzione ad HP, dovrà sostenere le spese di spedizione
e di manodopera per il servizio.
Customer Self Repair
HP Produkte enthalten viele CSR-Teile (Customer Self Repair), um Reparaturzeiten zu minimieren und höhere
Flexibilität beim Austausch defekter Bauteile zu ermöglichen. Wenn HP (oder ein HP Servicepartner) bei der
Diagnose feststellt, dass das Produkt mithilfe eines CSR-Teils repariert werden kann, sendet Ihnen HP dieses
Bauteil zum Austausch direkt zu. CSR-Teile werden in zwei Kategorien unterteilt:
Zwingend – Teile, für die das Customer Self Repair-Verfahren zwingend vorgegeben ist. Wenn Sie den
Austausch dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und Arbeitskosten für diesen
Service berechnet.
Optional – Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch für Customer
Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP vornehmen lassen möchten,
können bei diesem Service je nach den für Ihr Produkt vorgesehenen Garantiebedingungen zusätzliche
Kosten anfallen.
HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog
sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag geliefert.
Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden gegen einen
Aufpreis verfügbar. Wenn Sie Hilfe benötigen, können Sie das HP technische Support Center anrufen und
sich von einem Mitarbeiter per Telefon helfen lassen. Den Materialien, die mit einem CSR-Ersatzteil geliefert
werden, können Sie entnehmen, ob das defekte Teil an HP zurückgeschickt werden muss. Wenn es
erforderlich ist, das defekte Teil an HP zurückzuschicken, müssen Sie dies innerhalb eines vorgegebenen
Zeitraums tun, in der Regel innerhalb von fünf (5) Geschäftstagen. Das defekte Teil muss mit der zugehörigen
Dokumentation in der Verpackung zurückgeschickt werden, die im Lieferumfang enthalten ist. Wenn Sie das
Customer self repair
8
Download from Www.Somanuals.com. All Manuals Search And Download.
defekte Teil nicht zurückschicken, kann HP Ihnen das Ersatzteil in Rechnung stellen. Im Falle von Customer
Self Repair kommt HP für alle Kosten für die Lieferung und Rücksendung auf und bestimmt den
Kurier-/Frachtdienst.
Weitere Informationen über das HP Customer Self Repair Programm erhalten Sie von Ihrem Servicepartner
vor Ort. Informationen über das CSR-Programm in Nordamerika finden Sie auf der HP Website unter
Parts-only Warranty Service (Garantieservice
ausschließlich für Teile)
Ihre HP Garantie umfasst möglicherweise einen Parts-only Warranty Service (Garantieservice ausschließlich
für Teile). Gemäß den Bestimmungen des Parts-only Warranty Service stellt HP Ersatzteile kostenlos zur
Verfügung.
Für den Parts-only Warranty Service ist das CSR-Verfahren zwingend vorgegeben. Wenn Sie den Austausch
dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und Arbeitskosten für diesen Service
berechnet.
Reparaciones del propio cliente
Los productos de HP incluyen muchos componentes que el propio usuario puede reemplazar (Customer Self
Repair, CSR) para minimizar el tiempo de reparación y ofrecer una mayor flexibilidad a la hora de realizar
sustituciones de componentes defectuosos. Si, durante la fase de diagnóstico, HP (o los proveedores o socios
de servicio de HP) identifica que una reparación puede llevarse a cabo mediante el uso de un componente
CSR, HP le enviará dicho componente directamente para que realice su sustitución. Los componentes CSR se
clasifican en dos categorías:
•
Obligatorio: componentes para los que la reparación por parte del usuario es obligatoria. Si solicita a
HP que realice la sustitución de estos componentes, tendrá que hacerse cargo de los gastos de
desplazamiento y de mano de obra de dicho servicio.
•
Opcional: componentes para los que la reparación por parte del usuario es opcional. Estos
componentes también están diseñados para que puedan ser reparados por el usuario. Sin embargo, si
precisa que HP realice su sustitución, puede o no conllevar costes adicionales, dependiendo del tipo de
servicio de garantía correspondiente al producto.
NOTA: Algunos componentes no están diseñados para que puedan ser reparados por el usuario. Para que
el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios autorizado
realice la sustitución de estos componentes. Dichos componentes se identifican con la palabra "No" en el
catálogo ilustrado de componentes.
Según la disponibilidad y la situación geográfica, los componentes CSR se enviarán para que lleguen a su
destino al siguiente día laborable. Si la situación geográfica lo permite, se puede solicitar la entrega en el
mismo día o en cuatro horas con un coste adicional. Si precisa asistencia técnica, puede llamar al Centro de
asistencia técnica de HP y recibirá ayuda telefónica por parte de un técnico. Con el envío de materiales
para la sustitución de componentes CSR, HP especificará si los componentes defectuosos deberán
devolverse a HP. En aquellos casos en los que sea necesario devolver algún componente a HP, deberá
hacerlo en el periodo de tiempo especificado, normalmente cinco días laborables. Los componentes
defectuosos deberán devolverse con toda la documentación relacionada y con el embalaje de envío. Si no
Customer self repair
9
Download from Www.Somanuals.com. All Manuals Search And Download.
enviara el componente defectuoso requerido, HP podrá cobrarle por el de sustitución. En el caso de todas
sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de
componentes y escogerá la empresa de transporte que se utilice para dicho servicio.
Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase en
contacto con su proveedor de servicios local. Si está interesado en el programa para Norteamérica, visite
Servicio de garantía exclusivo de componentes
La garantía limitada de HP puede que incluya un servicio de garantía exclusivo de componentes. Según las
condiciones de este servicio exclusivo de componentes, HP le facilitará los componentes de repuesto sin
cargo adicional alguno.
Para este servicio de garantía exclusivo de componentes, es obligatoria la sustitución de componentes por
parte del usuario (CSR). Si solicita a HP que realice la sustitución de estos componentes, tendrá que hacerse
cargo de los gastos de desplazamiento y de mano de obra de dicho servicio.
Customer Self Repair
Veel onderdelen in HP producten zijn door de klant zelf te repareren, waardoor de reparatieduur tot een
minimum beperkt kan blijven en de flexibiliteit in het vervangen van defecte onderdelen groter is. Deze
onderdelen worden CSR-onderdelen (Customer Self Repair) genoemd. Als HP (of een HP Service Partner) bij
de diagnose vaststelt dat de reparatie kan worden uitgevoerd met een CSR-onderdeel, verzendt HP dat
onderdeel rechtstreeks naar u, zodat u het defecte onderdeel daarmee kunt vervangen. Er zijn twee
categorieën CSR-onderdelen:
Verplicht: Onderdelen waarvoor reparatie door de klant verplicht is. Als u HP verzoekt deze onderdelen
voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in rekening gebracht.
Optioneel: Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn ontworpen
voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te vervangen, kunnen
daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type garantieservice voor het
product.
OPMERKING: Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband met
de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden vervangen.
Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met "Nee".
Afhankelijk van de leverbaarheid en de locatie worden CSR-onderdelen verzonden voor levering op de
eerstvolgende werkdag. Levering op dezelfde dag of binnen vier uur kan tegen meerkosten worden
aangeboden, indien dit mogelijk is gezien de locatie. Indien assistentie gewenst is, belt u een HP Service
Partner om via de telefoon technische ondersteuning te ontvangen. HP vermeldt in de documentatie bij het
vervangende CSR-onderdeel of het defecte onderdeel aan HP moet worden geretourneerd. Als het defecte
onderdeel aan HP moet worden teruggezonden, moet u het defecte onderdeel binnen een bepaalde
periode, gewoonlijk vijf (5) werkdagen, retourneren aan HP. Het defecte onderdeel moet met de
bijbehorende documentatie worden geretourneerd in het meegeleverde verpakkingsmateriaal. Als u het
defecte onderdeel niet terugzendt, kan HP u voor het vervangende onderdeel kosten in rekening brengen. Bij
reparatie door de klant betaalt HP alle verzendkosten voor het vervangende en geretourneerde onderdeel en
kiest HP zelf welke koerier/transportonderneming hiervoor wordt gebruikt.
Customer self repair 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Neem contact op met een Service Partner voor meer informatie over het Customer Self Repair programma
van HP. Informatie over Service Partners vindt u op de HP website (http://www.hp.com/go/selfrepair).
Garantieservice "Parts Only"
Het is mogelijk dat de HP garantie alleen de garantieservice "Parts Only" omvat. Volgens de bepalingen van
de Parts Only garantieservice zal HP kosteloos vervangende onderdelen ter beschikking stellen.
Voor de Parts Only garantieservice is vervanging door CSR-onderdelen verplicht. Als u HP verzoekt deze
onderdelen voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in rekening
gebracht.
Reparo feito pelo cliente
Os produtos da HP são projetados com muitas peças para reparo feito pelo cliente (CSR) de modo a
minimizar o tempo de reparo e permitir maior flexibilidade na substituição de peças com defeito. Se,
durante o período de diagnóstico, a HP (ou fornecedores/parceiros de serviço da HP) concluir que o reparo
pode ser efetuado pelo uso de uma peça CSR, a peça de reposição será enviada diretamente ao cliente.
Existem duas categorias de peças CSR:
Obrigatória – Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua essas peças,
serão cobradas as despesas de transporte e mão-de-obra do serviço.
Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o
reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de
taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.
OBSERVAÇÃO: Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de
cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças estão
identificadas com a marca "No" (Não), no catálogo de peças ilustrado.
Conforme a disponibilidade e o local geográfico, as peças CSR serão enviadas no primeiro dia útil após o
pedido. Onde as condições geográficas permitirem, a entrega no mesmo dia ou em quatro horas pode ser
feita mediante uma taxa adicional. Se precisar de auxílio, entre em contato com o Centro de suporte técnico
da HP para que um técnico o ajude por telefone. A HP especifica nos materiais fornecidos com a peça CSR
de reposição se a peça com defeito deve ser devolvida à HP. Nos casos em que isso for necessário, é
preciso enviar a peça com defeito à HP dentro do período determinado, normalmente cinco (5) dias úteis.
A peça com defeito deve ser enviada com a documentação correspondente no material de transporte
fornecido. Caso não o faça, a HP poderá cobrar a reposição. Para as peças de reparo feito pelo cliente, a
HP paga todas as despesas de transporte e de devolução da peça e determina a transportadora/serviço
postal a ser utilizado.
Para obter mais informações sobre o programa de reparo feito pelo cliente da HP, entre em contato com o
fornecedor de serviços local. Para o programa norte-americano, visite o site da HP
Serviço de garantia apenas para peças
A garantia limitada da HP pode incluir um serviço de garantia apenas para peças. Segundo os termos do
serviço de garantia apenas para peças, a HP fornece as peças de reposição sem cobrar nenhuma taxa.
Customer self repair 11
Download from Www.Somanuals.com. All Manuals Search And Download.
No caso desse serviço, a substituição de peças CSR é obrigatória. Se desejar que a HP substitua essas
peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
Customer self repair 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer self repair 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer self repair 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer self repair 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer self repair 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrated parts catalog
Mechanical components
Item
Description
Assembly part Spare part
Customer
number
number
self repair
Access panel
Air baffle
463177-002
579551-001
—
602505-001
602508-001
602506-001
—
Mandatory1
Mandatory1
Mandatory1
—
1
2
3
Hardware kit
a) Fan blank
507009-001
b) Optical blank
505953-001
499244-002
507011-001
—
—
—
—
—
—
—
—
—
—
—
c) Power supply blank
602506-001
d) PCI expansion slot blank, full-length*
—
—
—
—
—
—
—
—
e) PCI expansion slot blank, short, low-profile* 507012-001
f) PCI retainer*
509084-001
509085-001
509086-001
509087-001
373134-001
352993-001
g) PCI retainer, top*
h) PCI retainer, end*
i) PCI retainer, removable*
j) T-10/T-15 Torx screwdriver holder*
k) Power cord retainer clip*
Illustrated parts catalog 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
Assembly part Spare part
Customer
number
number
self repair
l) T-10/T-15 Torx screwdriver*
377511-001
—
—
Front right bezel
507415-001
376383-002
336461-001
493297-001
463180-001
463179-001
—
602511-001
392613-001
389015-001
496080-001
496067-001
496063-001
289545-001
Mandatory1
Mandatory1
Mandatory1
Mandatory1
Mandatory1
Optional2
4
Hard drive blank, SFF
Hard drive blank, slimline interlock LFF*
Front left bezel
5
6
7
Fan cage
8
Power supply cage assembly
Return kit, pack box, and cushions*
9
Mandatory1
10
*Not shown
1Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be
charged for the travel and labor costs of this service.
2Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If,
however, you require that HP replace them for you, there may or may not be additional charges, depending on the type
of warranty service designated for your product.
3No—Some HP parts are not designed for customer self repair. In order to satisfy the customer warranty, HP requires that
an authorized service provider replace the part. These parts are identified as "No" in the Illustrated Parts Catalog.
1Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de
remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
2Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également
conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous demandez à HP de remplacer ces
pièces, l'intervention peut ou non vous être facturée, selon le type de garantie applicable à votre produit.
3No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la réparation. Pour
que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit effectué par un Mainteneur Agréé. Ces
pièces sont identifiées par la mention “Non” dans le Catalogue illustré.
1Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne affida la
riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il servizio.
2Optional: Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di componenti
progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP, potrebbe dover sostenere spese
addizionali a seconda del tipo di garanzia previsto per il prodotto.
3No: Non CSR—Alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per rispettare la
garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato. Tali parti sono identificate
da un “No” nel Catalogo illustrato dei componenti.
1Mandatory: Zwingend—Teile, die im Rahmen des Customer Self Repair Programms ersetzt werden müssen. Wenn Sie
diese Teile von HP ersetzen lassen, werden Ihnen die Versand- und Arbeitskosten für diesen Service berechnet.
2Optional: Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch für Customer
Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP vornehmen lassen möchten, können bei
diesem Service je nach den für Ihr Produkt vorgesehenen Garantiebedingungen zusätzliche Kosten anfallen.
3No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen,
muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit „No“ bzw.
„Nein“ gekennzeichnet.
1Mandatory: Obligatorio—componentes para los que la reparación por parte del usuario es obligatoria. Si solicita a HP
que realice la sustitución de estos componentes, tendrá que hacerse cargo de los gastos de desplazamiento y de mano
de obra de dicho servicio.
2Optional: Opcional— componentes para los que la reparación por parte del usuario es opcional. Estos componentes
también están diseñados para que puedan ser reparados por el usuario. Sin embargo, si precisa que HP realice su
Illustrated parts catalog 18
Download from Www.Somanuals.com. All Manuals Search And Download.
sustitución, puede o no conllevar costes adicionales, dependiendo del tipo de servicio de garantía correspondiente al
producto.
3No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario. Para que el usuario
haga valer su garantía, HP pone como condición que un proveedor de servicios autorizado realice la sustitución de estos
componentes. Dichos componentes se identifican con la palabra “No” en el catálogo ilustrado de componentes.
1Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt deze onderdelen te
vervangen, komen de reiskosten en het arbeidsloon voor uw rekening.
2Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn
ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te vervangen, kunnen
daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type garantieservice voor het product.
3No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband met de
garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden vervangen. Deze
onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met "Nee".
1Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua essas peças,
serão cobradas as despesas de transporte e mão-de-obra do serviço.
2Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o
reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa
adicional, dependendo do tipo de serviço de garantia destinado ao produto.
3No: Nenhuma—Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de cumprir a garantia
do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças estão identificadas com a marca “No”
(Não), no catálogo de peças ilustrado.
Illustrated parts catalog 19
Download from Www.Somanuals.com. All Manuals Search And Download.
System components
Item Description
System components
Assembly
part number number
Spare part
Customer
self repair
Full-length expansion board shipping bracket*
—
618597-001
Mandatory1
Mandatory1
11
Hot-plug fan
463172-001
—
496066-001
—
12
13
Hot-plug power supplies
a) 460 W
—
499249-001
511777-001
Mandatory1
b) 460 W HE 94%*
c) 750 W*
591553-001
506821-001
591554-001
490594-001
570451-101
444049-001
599381-001
511778-001
599383-001
498152-001
579229-001
451816-001
Mandatory1
Mandatory1
Mandatory1
Mandatory1
Mandatory1
Mandatory1
d) 750 W HE 94%*
e) 1200 W*
f) 1200 W HE 94%*
g) 1200 W DC*
PCI riser cage with non-hot-plug PCIe riser
Optical drive cage
463170-003
463175-001
—
614778-001
496076-001
—
Optional2
Mandatory1
—
14
15
16
Hard drive cage
a) SFF hard drive cage
b) LFF hard drive cage*
Processor
463173-001
463174-001
496074-001
496075-001
Mandatory1
Mandatory1
—
—
—
17
a) 2.0-GHz, 8C AMD Opteron™ Model
6128**
578022-003
598732-001
Optional2
Illustrated parts catalog 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Item Description
Assembly
Spare part
Customer
part number number
self repair
b) 2.0-GHz, 8C AMD Opteron™ Model
6128HE* **
c) 2.2-GHz 8C AMD Opteron™ Model
6132HE* **
d) 2.3-GHz, 8C AMD Opteron™ Model 6134* 578022-002
578023-001
578023-005
583751-001
Optional2
Optional2
Optional2
633546-001
583752-001
**
e) 2.4-GHz, AMD Opteron™ Model 6136* ** 578022-001
583753-001
633544-001
Optional2
Optional2
f) 2.6-GHz 8C AMD Opteron™ Model 6140* 578022-006
**
g) 1.8-GHz 12C AMD Opteron™ Model
6166HE* **
h) 2.1-GHz, 12C AMD Opteron™ Model
6172* **
i) 2.2-GHz 12C AMD Opteron™ Model 6174* 578015-005
**
j) 2.3-GHz 12C AMD Opteron™ Model 6176* 578015-006
**
k) 2.3-GHz 12C AMD Opteron™ Model
6176SE* **
l) 2.5-GHz 12C AMD Opteron™ Model
6180SE* **
m) 2.6-GHz 8C AMD Opteron™ Model 6212* 655497-002
596136-002
633545-001
583755-001
598729-001
633722-001
599220-001
634956-001
662840-001
662839-001
662838-001
662837-001
662841-001
662836-001
662835-001
662834-001
663779-001
592068-001
Optional2
Optional2
Optional2
Optional2
Optional2
Optional2
Optional2
Optional2
Optional2
Optional2
Optional2
Optional2
Optional2
Optional2
Optional2
Optional2
578015-001
596121-001
596121-003
**
n) 3.0-GHz 8C AMD Opteron™ Model 6220* 655497-001
**
o) 2.4-GHz 12C AMD Opteron™ Model 6234* 654523-002
**
p) 2.6-GHz 12C AMD Opteron™ Model
6238* **
q) 1.6-GHz 16C AMD Opteron™ Model
6262HE* **
r) 2.1-GHz 16C AMD Opteron™ Model 6272* 654522-003
654523-001
654524-001
**
s) 2.2-GHz 16C AMD Opteron™ Model 6274* 654522-002
**
t) 2.3-GHz 16C AMD Opteron™ Model 6276* 654521-001
**
u) 2.6-GHz 16C AMD Opteron™ Model
6282SE* **
654868-001
Processor heatsink, thermal grease, and alcohol 579554-001
18
19
pad, 80-Watt
Boards
System board components
a) System board assembly
—
—
—
570047-001
583981-001
Optional2
b) System board assembly with subpan*
570047-002
669515-001
Optional2
Power supply backplane
Hard drive backplane
a) SFF SAS backplane
462952-001
—
496062-001
—
Optional2
—
Optional2
20
21
451283-002
507690-001
Illustrated parts catalog 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Item Description
Assembly
Spare part
Customer
part number number
self repair
b) LFF SAS backplane*
457174-003
457174-002
602510-001
Optional2
Optional2
c) 6-bay hard drive backplane*
577427-001
Systems Insight Display
Controller board
570048-001
013233-001
583984-001
462919-001
Mandatory1
Mandatory1
22
23
PCI riser boards*
a) PCI-X
—
—
—
24
533537-001
583983-001
Mandatory1
b) PCIe
533536-001
451282-001
583982-001
507688-001
Mandatory1
Mandatory1
c) Dual-port
Memory
DIMMs*
—
—
—
25
a) 2-GB, dual-rank, PC3-10600, registered
500202-161
595094-001
Mandatory1
b) 2-GB, quad-rank, PC3-10600E
c) 4-GB, single-rank, PC3-10600, unbuffered
d) 4-GB, dual-rank, PC3-10600, registered
e) 8-GB, dual-rank, PC3-10600, registered
f) 8-GB, dual-rank, PC3L-10600, registered
g) 16-GB, dual-rank, PC3-8500, registered
Cables
500209-161
500210-171
591750-171
500205-171
605313-171
500207-171
595101-001
595102-001
595096-001
595097-001
606425-001
595098-001
Mandatory1
Mandatory1
Mandatory1
Mandatory1
Mandatory1
Mandatory1
SAS backplane cable, 83.8 cm (33.0 in)*
SATA DVD power cable*
463184-001
463209-001
493228-006
582248-001
142263-001
496070-001
496071-001
498426-001
602509-001
142258-001
Mandatory1
Mandatory1
Mandatory1
Mandatory1
Mandatory1
26
27
28
29
30
Mini-SAS to mini-SAS cable*
Hard drive backplane power cable*
AC power cord*
Battery cable, 60 cm (24 in)*
Miscellaneous cable kit*
a) Hard drive cable
458943-003
—
488138-001
602507-001
—
Mandatory1
31
32
—
582248-002
Mandatory1
b) Systems Insight Display cable
582247-001
—
Mandatory1
Rack mounting hardware
Rack mounting hardware kit, LFF*
Rack mounting hardware kit, SFF*
Miscellaneous
491732-001
487267-001
574898-001
574765-001
Optional2
Optional2
33
34
Battery, 3.3-V, lithium*
Power supply, 48V*
Options
166899-001
444049-001
153099-001
451816-001
Mandatory1
Optional2
35
36
Hot-plug hard drive*
—
—
—
37
a) 36-GB, SAS, 10,000-rpm, 6 cm (2.5-in)
375859-B21
376596-001
Mandatory1
b) 72-GB, SAS, 10,000-rpm, 6 cm (2.5-in)
375861-B21
376597-001
Mandatory1
Illustrated parts catalog 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Item Description
Assembly
Spare part
Customer
part number number
self repair
Mandatory1
c) 60-GB SFF SATA hard drive, 5,400-rpm, 1-yr 379306-B21
382264-001
warranty
Array controllers*
—
—
—
38
a) Smart Array E200 Controller
012891-001
412799-001
412800-001
Optional2
b) Smart Array E200 Controller cache module, 012970-001
Optional2
64-MB
c) Smart Array E200 Controller cache module, 012795-001
128-MB
413486-001
Optional2
d) Smart Array P400 Controller
e) Smart Array P410 Controller
f) Smart Array P411 Controller
013159-003
013233-001
013236-001
405831-001
462919-001
462918-001
405836-001
Optional2
Optional2
Optional2
Optional2
g) Smart Array P400 Controller cache module, 012764-004
256-MB
h) Smart Array P400 Controller cache module, 012764-003
512-MB
i) Smart Array P400 Controller battery
405835-001
Optional2
381573-001
398648-001
409125-001
Optional2
Optional2
j) Smart Array P400 Controller battery cable
assembly, 24-in
HP Trusted Platform Module*
408658-002
450168-001
570501-002
571436-002
505836-001
505908-001
587324-001
No3
Mandatory1
Mandatory1
39
40
41
Flash-Backed Write Cache Module, 1-GB*
Battery-Backed Module with cable*
*Not shown
**All processors in this HP ProLiant server must have the same cache size, speed, number of cores, and rated maximum
power consumption.
1Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be
charged for the travel and labor costs of this service.
2Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If,
however, you require that HP replace them for you, there may or may not be additional charges, depending on the type
of warranty service designated for your product.
3No—Some HP parts are not designed for customer self repair. In order to satisfy the customer warranty, HP requires that
an authorized service provider replace the part. These parts are identified as "No" in the Illustrated Parts Catalog.
1Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de
remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
2Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également
conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous demandez à HP de remplacer ces
pièces, l'intervention peut ou non vous être facturée, selon le type de garantie applicable à votre produit.
3No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la réparation. Pour
que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit effectué par un Mainteneur Agréé. Ces
pièces sont identifiées par la mention “Non” dans le Catalogue illustré.
1Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne affida la
riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il servizio.
2Optional: Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di componenti
progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP, potrebbe dover sostenere spese
addizionali a seconda del tipo di garanzia previsto per il prodotto.
Illustrated parts catalog 23
Download from Www.Somanuals.com. All Manuals Search And Download.
3No: Non CSR—Alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per rispettare la
garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato. Tali parti sono identificate
da un “No” nel Catalogo illustrato dei componenti.
1Mandatory: Zwingend—Teile, die im Rahmen des Customer Self Repair Programms ersetzt werden müssen. Wenn Sie
diese Teile von HP ersetzen lassen, werden Ihnen die Versand- und Arbeitskosten für diesen Service berechnet.
2Optional: Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch für Customer
Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP vornehmen lassen möchten, können bei
diesem Service je nach den für Ihr Produkt vorgesehenen Garantiebedingungen zusätzliche Kosten anfallen.
3No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen,
muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit „No“ bzw.
„Nein“ gekennzeichnet.
1Mandatory: Obligatorio—componentes para los que la reparación por parte del usuario es obligatoria. Si solicita a HP
que realice la sustitución de estos componentes, tendrá que hacerse cargo de los gastos de desplazamiento y de mano
de obra de dicho servicio.
2Optional: Opcional— componentes para los que la reparación por parte del usuario es opcional. Estos componentes
también están diseñados para que puedan ser reparados por el usuario. Sin embargo, si precisa que HP realice su
sustitución, puede o no conllevar costes adicionales, dependiendo del tipo de servicio de garantía correspondiente al
producto.
3No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario. Para que el usuario
haga valer su garantía, HP pone como condición que un proveedor de servicios autorizado realice la sustitución de estos
componentes. Dichos componentes se identifican con la palabra “No” en el catálogo ilustrado de componentes.
1Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt deze onderdelen te
vervangen, komen de reiskosten en het arbeidsloon voor uw rekening.
2Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn
ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te vervangen, kunnen
daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type garantieservice voor het product.
3No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband met de
garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden vervangen. Deze
onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met "Nee".
1Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua essas peças,
serão cobradas as despesas de transporte e mão-de-obra do serviço.
2Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o
reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa
adicional, dependendo do tipo de serviço de garantia destinado ao produto.
3No: Nenhuma—Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de cumprir a garantia
do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças estão identificadas com a marca “No”
(Não), no catálogo de peças ilustrado.
Illustrated parts catalog 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrated parts catalog 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Required tools
You need the following items for some procedures:
•
•
T-10/T-15 Torx screwdriver (provided inside the server)
Safety considerations
Before performing service procedures, review all the safety information.
Preventing electrostatic discharge
To prevent damaging the system, be aware of the precautions you need to follow when setting up the system
or handling parts. A discharge of static electricity from a finger or other conductor may damage system
boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
To prevent electrostatic damage:
•
•
•
•
•
Avoid hand contact by transporting and storing products in static-safe containers.
Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
Place parts on a grounded surface before removing them from their containers.
Avoid touching pins, leads, or circuitry.
Always be properly grounded when touching a static-sensitive component or assembly.
Server warnings and cautions
Before installing a server, be sure that you understand the following warnings and cautions.
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against it.
Pay particular attention to the plug, electrical outlet, and the point where the cord extends from
the server.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
Removal and replacement procedures 26
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: Do not operate the server for long periods with the access panel open or removed.
Operating the server in this manner results in improper airflow and improper cooling that can
lead to thermal damage.
Preparation procedures
To access some components and perform certain service procedures, you must perform one or more of the
following procedures:
•
If you are performing service procedures in an HP, Compaq branded, telco, or third-party rack cabinet,
you can use the locking feature of the rack rails to support the server and gain access to internal
components.
For more information about telco rack solutions, refer to the RackSolutions.com website
•
•
If you must remove a server from a rack or a non-hot-plug component from a server, power down the
server.
If the rack environment, cabling configuration, or the server location in the rack creates awkward
conditions, remove the server from the rack.
Power down the server
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
IMPORTANT: If installing a hot-plug device, it is not necessary to power down the server.
1.
2.
Back up the server data.
Shut down the operating system as directed by the operating system documentation.
NOTE: If the operating system automatically places the server in Standby mode, omit the next
step.
3.
Press the Power On/Standby button to place the server in Standby mode. When the server activates
Standby power mode, the system power LED changes to amber.
IMPORTANT: Pressing the UID button illuminates the blue UID LEDs on the front and rear panels.
In a rack environment, this feature facilitates locating a server when moving between the front and
rear of the rack.
4.
Disconnect the power cords.
The system is now without power.
Removal and replacement procedures 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Extend the server from the rack
1.
2.
Pull down the quick release levers on each side of the server.
Extend the server from the rack.
WARNING: To reduce the risk of personal injury or equipment damage, be sure that the rack is
adequately stabilized before extending a component from the rack.
3.
After performing the installation or maintenance procedure, slide the server back into the rack, and then
press the server firmly into the rack to secure it in place.
WARNING: To reduce the risk of personal injury, be careful when pressing the server rail-release
latches and sliding the server into the rack. The sliding rails could pinch your fingers.
Remove the server from the rack
To remove the server from an HP, Compaq branded, telco, or third-party rack:
Removal and replacement procedures 28
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
2.
3.
Disconnect the cabling and remove the server from the rack. For more information, refer to the
documentation that ships with the rack mounting option.
4.
Place the server on a sturdy, level surface.
Access the product rear panel
Cable management arm with left-hand swing
To access the server rear panel:
1.
Remove the cable arm retainer.
2.
Open the cable management arm.
Removal and replacement procedures 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable management arm with right-hand swing
NOTE: To access some components, you may need to remove the cable management arm.
To access the product rear panel components, open the cable management arm:
1.
2.
3.
4.
Swing open the cable management arm.
Remove the cables from the cable trough.
Remove the cable management arm.
SAS hard drive blank
CAUTION: For proper cooling do not operate the server without the access panel, baffles,
expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize
the amount of time the access panel is open.
Remove the component as indicated.
To replace the blank, slide the blank into the bay until it locks into place.
Removal and replacement procedures 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Hot-plug SAS hard drive
To remove the component:
CAUTION: For proper cooling do not operate the server without the access panel, baffles,
expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize
the amount of time the access panel is open.
1.
2.
3.
Back up all server data on the hard drive.
Remove the hard drive.
To replace the component, reverse the removal procedure.
Power supply blank
To remove the component:
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
1.
2.
Remove the power supply blank.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the power supply or
power supply blank to cool before touching it.
Removal and replacement procedures 31
Download from Www.Somanuals.com. All Manuals Search And Download.
To replace the component, reverse the removal procedure.
Hot-plug power supply
WARNING: To reduce the risk of personal injury from hot surfaces, allow the power supply or
power supply blank to cool before touching it.
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
To remove the component:
1.
Determine how many hot-plug power supplies are installed:
o
If only one hot-plug power supply is installed, power down and remove the power cord from the
o
If more than one hot-plug power supply is installed, continue with the next step.
2.
3.
Disconnect the power cord from the power supply.
Removal and replacement procedures 32
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
Remove the hot-plug power supply.
WARNING: To reduce the risk of electric shock or damage to the equipment, do not connect the
power cord to the power supply until the power supply is installed.
To replace the component:
1.
2.
3.
4.
Slide the hot-plug power supply into the power supply bay.
Connect the power cord to the power supply.
Route the power cord through the cable management arm or power cord anchor.
NOTE: If using the power cord anchor, be sure to leave enough slack in the power cord so that
the redundant power supply can be removed without disconnecting the power cord from the
primary power supply.
5.
6.
7.
Close the cable management arm.
Connect the power cord to the power source.
8.
Be sure that the front panel external health LED is green ("Front panel LEDs and buttons" on page 82).
Front right bezel
To remove the component:
1.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
Removal and replacement procedures 33
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Remove the three T-10 Torx screws, and then detach the front bezel.
To replace the component, reverse the removal procedure.
Access panel
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
CAUTION: For proper cooling do not operate the server without the access panel, baffles,
expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize
the amount of time the access panel is open.
To remove the component:
1.
2.
3.
Use the T-15 Torx screwdriver attached to the rear of the server to loosen the security screw on the hood
latch.
4.
Lift up on the hood latch handle, and then remove the access panel.
To replace the component, reverse the removal procedure.
Optical drive
To remove the component:
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
1.
Removal and replacement procedures 34
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
Disconnect the cable from the optical drive.
5.
Remove the optical drive.
To replace the component, reverse the removal procedure.
Optical drive cage
To remove the component:
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
1.
Removal and replacement procedures 35
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
Disconnect the cable from the optical drive.
5.
6.
Remove the optical drive cage.
To replace the component, reverse the removal procedure.
Hot-plug fan
CAUTION: To avoid damage to server components, fan blanks must be installed in fan bays 5
and 6 in a single-processor configuration.
The only two valid fan configurations are listed in the following table.
Removal and replacement procedures 36
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
Fan bay 1 Fan bay 2 Fan bay 3 Fan bay 4 Fan bay 5 Fan bay 6
Fan
Fan
Fan
Fan
Fan
Fan
Fan
Fan
Fan blank
Fan
Fan blank
Fan
1 processor
2 processors
For a single-processor configuration, four fans and two blanks are required in specific fan bays for
redundancy. A fan failure or missing fan causes all fans to spin at high speed. A second fan failure or missing
fan causes an orderly shutdown of the server.
Installing more than the required number of fans in a single-processor configuration is not a thermally
supported configuration.
For a dual-processor configuration, six fans are required for redundancy. A fan failure or missing fan causes
all fans to spin at high speed. A second fan failure or missing fan causes an orderly shutdown of the server.
The server supports variable fan speed. The fans operate at minimum speed until a temperature change
requires a fan speed increase to cool the server. The server shuts down during the following
temperature-related scenarios:
•
At POST and in the OS, iLO 3 performs an orderly shutdown if a cautionary temperature level is
detected. If the server hardware detects a critical temperature level before an orderly shutdown occurs,
the server performs an immediate shutdown.
•
When the Thermal Shutdown feature is disabled in RBSU, iLO 3 does not perform an orderly shutdown
when a cautionary temperature level is detected. Disabling this feature does not disable the server
hardware from performing an immediate shutdown when a critical temperature level is detected.
CAUTION: A thermal event can damage server components when the Thermal Shutdown feature
is disabled in RBSU.
To remove the component:
1.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
2.
Removal and replacement procedures 37
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Remove the fan.
CAUTION: Do not operate the server for long periods with the access panel open or removed.
Operating the server in this manner results in improper airflow and improper cooling that can
lead to thermal damage.
To replace the component, reverse the removal procedure.
Power supply backplane
To remove the component:
1.
2.
3.
4.
Removal and replacement procedures 38
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Remove the power supply backplane.
To replace the component, reverse the removal procedure.
SFF hard drive backplane
To remove the component:
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
5.
Disconnect all cables from the hard drive backplane.
Removal and replacement procedures 39
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
Remove the hard drive backplane.
To replace the component, reverse the removal procedure.
SFF hard drive cage
To remove the component:
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
5.
6.
Disconnect all cables from the hard drive backplane.
Removal and replacement procedures 40
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
Remove the hard drive cage.
To replace the component, reverse the removal procedure.
LFF hard drive backplane
To remove the component:
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
5.
Disconnect all cables from the hard drive backplane.
Removal and replacement procedures 41
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
Remove the hard drive backplane.
To replace the component, reverse the removal procedure.
LFF hard drive cage
To remove the component:
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
5.
6.
Disconnect all cables from the hard drive backplane.
Removal and replacement procedures 42
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
Remove the hard drive cage.
To replace the component, reverse the removal procedure.
Full-length expansion board shipping bracket
CAUTION: To prevent damage to the server or expansion boards, power down the server and
remove all AC power cords before removing or installing the PCI riser cage.
1.
2.
3.
4.
Remove the full-length expansion board shipping bracket:
o
If no full-length expansion boards are installed, remove the full-length expansion board shipping
bracket as indicated.
Removal and replacement procedures 43
Download from Www.Somanuals.com. All Manuals Search And Download.
o
If full-length expansion boards are installed, remove the full-length expansion board shipping
bracket as indicated.
PCI riser cage
To remove the component:
CAUTION: To prevent damage to the server or expansion boards, power down the server and
remove all AC power cords before removing or installing the PCI riser cage.
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
If any full-length expansion boards are installed, remove the full-length expansion board shipping
Removal and replacement procedures 44
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Remove the PCI riser cage.
To replace the component, reverse the removal procedure.
Expansion slot covers
CAUTION: To prevent damage to the server or expansion boards, power down the server and
remove all AC power cords before removing or installing the PCI riser cage.
CAUTION: For proper cooling do not operate the server without the access panel, baffles,
expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize
the amount of time the access panel is open.
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
If any full-length expansion boards are installed, remove the full-length expansion board shipping
5.
6.
Remove the expansion slot cover:
Removal and replacement procedures 45
Download from Www.Somanuals.com. All Manuals Search And Download.
o
To remove slot cover 1 or 4, push in on the retainer to release it, and then slide out the cover.
o
To remove slot covers 2 and 3, lift up on the latch, remove the latch, and then remove the cover.
Removal and replacement procedures 46
Download from Www.Somanuals.com. All Manuals Search And Download.
o
To remove slot covers 5 and 6, push down on the latch, rotate the latch down, and then remove the
cover.
Expansion boards
Half-length expansion board
To remove the component:
1.
2.
3.
4.
5.
6.
Disconnect any external cables that are connected to the expansion board.
Disconnect any internal cables that are connected to the expansion board.
Removal and replacement procedures 47
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
Remove the expansion board.
To replace the component, reverse the removal procedure.
Full-length expansion board
To remove the component:
1.
2.
3.
4.
5.
6.
7.
Disconnect any external cables that are connected to the expansion board.
Disconnect any internal cables that are connected to the expansion board.
Remove the expansion board.
Removal and replacement procedures 48
Download from Www.Somanuals.com. All Manuals Search And Download.
To replace the component, reverse the removal procedure.
Air baffle
To remove the component:
CAUTION: For proper cooling do not operate the server without the access panel, baffles,
expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize
the amount of time the access panel is open.
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
CAUTION: Do not detach the cable that connects the battery pack to the cache module.
Detaching the cable causes any unsaved data in the cache module to be lost.
4.
5.
Remove the air baffle.
To replace the component, reverse the removal procedure.
Battery-backed write cache procedures
Two types of procedures are provided for the BBWC option:
•
Removal and replacement of failed components:
o
o
•
Removal and replacement procedures 49
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: Do not detach the cable that connects the battery pack to the cache module.
Detaching the cable causes any unsaved data in the cache module to be lost.
Removing the cache module
To remove the component:
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
5.
6.
Remove the cache module.
To replace the component, reverse the removal procedure.
CAUTION: To prevent damage to the cache module during installation, be sure the cache
module is fully inserted before pressing down.
Removing the battery pack
To remove the component:
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
Removal and replacement procedures 50
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Disconnect the cable, and then remove the battery pack.
To replace the component, reverse the removal procedure.
Recovering data from the battery-backed write cache
If the server fails, use the following procedure to recover data temporarily stored in the BBWC.
CAUTION: Before starting this procedure, read the information about protecting against
1.
2.
Perform one of the following:
o
Set up a recovery server station using an identical server model. Do not install any internal drives or
BBWC in this server. (HP recommends this option.)
o
Find a server that has enough empty drive bays to accommodate all the drives from the failed server
and that meets all the other requirements for drive and array migration.
Power down the failed server ("Power down the server" on page 27). If any data is stored in the cache
module, a green LED on the module flashes every 2 seconds.
CAUTION: Do not detach the cable that connects the battery pack to the cache module.
Detaching the cable causes any unsaved data in the cache module to be lost.
3.
4.
Transfer the hard drives from the failed server to the recovery server station.
Perform one of the following:
o
and install the cache module and battery pack on an array controller in the recovery server.
o
the controller, cache module, and battery pack in the recovery server.
Removal and replacement procedures 51
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Power up the recovery server. A 1759 POST message is displayed, stating that valid data was flushed
from the cache. This data is now stored on the drives in the recovery server. You can now transfer the
drives (and controller, if one was used) to another server.
Flash-backed write cache procedures
Two types of procedures are provided for the FBWC option:
•
Removal and replacement of failed components:
o
o
Removing the cache module
•
CAUTION: Do not detach the cable that connects the battery pack or capacitor pack to the cache
module. Detaching the cable causes any unsaved data in the cache module to be lost.
Flash-backed write cache module
To remove the component:
CAUTION: Do not use this controller with cache modules designed for other controller models,
because the controller can malfunction and you can lose data. Also, do not transfer this cache
module to a different controller module, because you can lose data.
1.
2.
3.
Back up all data.
Close all applications.
CAUTION: In systems that use external data storage, be sure that the server is the first unit to be
powered down and the last to be powered back up. Taking this precaution ensures that the system
does not erroneously mark the drives as failed when the server is powered up.
4.
5.
6.
7.
If the existing cache module is connected to a capacitor pack, observe the FBWC module LEDs (on
o
If the amber LED is flashing, data is trapped in the cache. Restore system power, and restart this
procedure from step 1.
o
If the amber LED is not illuminated, remove the controller from the server, and then continue with the
next step.
Removal and replacement procedures 52
Download from Www.Somanuals.com. All Manuals Search And Download.
8.
Open the ejector latches on each side of the cache module connector. Normally, the cache module is
ejected from the cache module connector. If the module is not ejected automatically, remove the cache
module.
9.
If the cache module is connected to a capacitor pack, disconnect the capacitor pack cable from the
connector on the top of the cache module.
To replace the component, reverse the removal procedure.
CAUTION: To prevent damage to the cache module during installation, be sure the cache
module is fully inserted before pressing down.
Flash-backed write cache capacitor pack
To remove the component:
1.
2.
3.
Back up all data.
Close all applications.
Removal and replacement procedures 53
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: In systems that use external data storage, be sure that the server is the first unit to be
powered down and the last to be powered back up. Taking this precaution ensures that the system
does not erroneously mark the drives as failed when the server is powered up.
4.
5.
6.
7.
If the capacitor pack is connected to the cache module, disconnect the capacitor pack cable from the
connector on the top of the cache module.
8.
Disconnect the capacitor pack from the air baffle.
To replace the component, reverse the removal procedure.
Fan cage
To remove the component:
Removal and replacement procedures 54
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
5.
6.
7.
8.
Remove the fan blanks.
Remove the fan cage.
To replace the component, reverse the removal steps. Press down on the top of each fan to be sure it is seated
properly.
Heatsink
To remove the heatsink:
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
5.
Removal and replacement procedures 55
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
Open the heatsink retaining bracket, and then remove the heatsink.
To replace the heatsink:
1.
Clean the old thermal grease from the processor with the alcohol swab. Allow the alcohol to evaporate
before continuing.
2.
Remove the heatsink protective cover.
Removal and replacement procedures 56
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Install the heatsink.
4.
Close and lock the heatsink retaining latches.
5.
6.
7.
8.
9.
Install the server into the rack.
Power up the server.
Processor
CAUTION: To avoid damage to the processor and system board, only authorized personnel
should attempt to replace or install the processor in this server.
Removal and replacement procedures 57
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: To prevent possible server malfunction and damage to the equipment, multiprocessor
configurations must contain processors with the same part number.
To remove a processor:
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
5.
6.
Open the processor socket retaining bracket and the processor locking lever.
7.
Using the processor tool, remove the processor from the system board.
Removal and replacement procedures 58
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: To avoid damage to the processor, do not touch the bottom of the processor,
especially the contact area.
To replace a processor:
IMPORTANT: Be sure the processor remains inside the processor installation tool.
1.
If the processor has separated from the installation tool, carefully re-insert the processor in the tool.
Handle the processor by the edges only, and do not touch the bottom of the processor, especially the
contact area.
2.
The processor fits one way into the socket. Use the alignment guides on the processor and socket to
properly align the processor with the socket. Install the spare processor. THE PINS ON THE SYSTEM
BOARD ARE VERY FRAGILE AND EASILY DAMAGED.
Removal and replacement procedures 59
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. To
avoid damage to the system board:
• Never install or remove a processor without using the processor installation tool.
• Do not touch the processor socket contacts.
• Do not tilt or slide the processor when lowering the processor into the socket.
3.
Press the tabs on the processor tool to release the processor, and then remove the processor tool.
4.
Close the processor socket retaining bracket and the processor locking lever.
CAUTION: Be sure to close the processor socket retaining bracket before closing the processor
locking lever. The lever should close without resistance. Forcing the lever closed can damage the
processor and socket, requiring system board replacement.
5.
Clean the old thermal grease from the heatsink with the alcohol swab. Allow the alcohol to evaporate
before continuing.
Removal and replacement procedures 60
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
Apply all the grease to the top of the processor in the following pattern to ensure even distribution.
7.
Install the heatsink.
Removal and replacement procedures 61
Download from Www.Somanuals.com. All Manuals Search And Download.
8.
Close and lock the heatsink retaining latches.
9.
12. Install the server into the rack.
13. Power up the server.
Memory configurations
This server supports 2 GB to 256 GB of system memory using DDR3 2-GB, 4-GB, 8-GB, and 16-GB memory
modules across 24 memory sockets.
Advanced ECC memory
Advanced ECC memory is the memory protection mode for this server. In Advanced ECC, the server does not
fail because of correctable memory errors. The server provides notification if the level of correctable errors
exceeds a pre-defined threshold rate.
Advanced ECC provides additional protection over standard ECC because it is possible to correct certain
memory errors that would otherwise be uncorrectable and result in a server failure.
Whereas standard ECC can correct single-bit memory errors, Advanced ECC can correct single-bit memory
errors and multi-bit memory errors if all failed bits are on the same DRAM device on the memory module.
Population order
The two tables below represent the memory module population order for one processor. The population
order for the other processor is identical. SR denotes Single Rank, DR denotes Dual Rank, and QR denotes
Quad Rank.
All memory modules must follow the population order shown in these two tables for both processors with the
following exception:
Removal and replacement procedures 62
Download from Www.Somanuals.com. All Manuals Search And Download.
•
QR memory modules must be installed only in memory sockets 2, 5, 8, and 11, while following the
population order for those memory sockets.
Processor
memory
socket
1
2
3
4
5
6
SR/DR
SR/DR/QR
SR/DR
SR/DR
SR/DR/QR
SR/DR
Rank support
per memory
socket
Population
order
A
I
E
C
K
G
A
A
A
B
B
B
Processor
memory
channel
Processor
memory
socket
7
8
9
10
11
12
SR/DR
SR/DR/QR
SR/DR
SR/DR
SR/DR/QR
SR/DR
Rank support
per memory
socket
Population
order
B
J
F
D
L
H
C
C
C
D
D
D
Processor
memory
channel
Population rules
When installing memory modules, observe the following population rules:
•
•
Use only HP memory modules listed in the DL385 QuickSpecs.
Advanced ECC is not available if x4 and x8 memory modules are mixed in channels (A and B), (C and
D), or both, but standard ECC is still available. Advanced ECC is available if x4 and x8 memory
modules are mixed in memory channels (A and C), (B and D), or both.
•
•
No more than two UDIMMs may be installed per channel.
Do not mix UDIMMs and RDIMMs within this server.
Population guidelines
improved by following the guidelines below:
•
Memory modules may be installed one at a time per processor, but installing two at a time per processor
provides for additional performance, installing four at a time per processor provides for better
Removal and replacement procedures 63
Download from Www.Somanuals.com. All Manuals Search And Download.
performance, and installing equal amounts of memory for both processors provides for best
performance.
•
•
Install all memory modules of the same speed on the same processor for best performance.
Install all memory modules of the same voltage on the same processor for best power.
Memory bus speed
Depending on the quantity and native speed of memory modules installed, memory bus speeds can be 1333
MHz, 1066 MHz, 800 MHz, or 667 MHz. Memory bus speeds can be different for each processor.
To determine memory bus speeds, do the following:
1.
2.
Within RBSU, select the Power Management Options menu > Advanced Power Management Options
menu > Maximum Memory Bus Frequency menu.
Select one of the following menu options:
o
Auto (default)—The memory bus speed is set to what is shown in the following table. If the native
speed of the installed memory module is slower than the memory bus speed, the memory bus speed
is set to the memory module native speed
Memory
modules per
channel
QR
SR or DR Memory
module native (standard-voltage
Memory bus speed
Memory bus speed
(low-voltage memory
module)
speed
memory module)
—
1*
SR 1333 MHz
DR 1333 MHz
DR 1066 MHz
1333 MHz
1333 MHz
1
1
—
QR 1066 MHz 1066 MHz
1066 MHz
1333 MHz
1
2
—
2*
SR 1333 MHz
DR 1333 MHz
DR 1066 MHz
SR 1333 MHz
DR 1333 MHz
DR 1066 MHz
QR 1066 MHz
SR 1333 MHz
1333 MHz
1
1
800 MHz
800 MHz
2
—
—
3 SR
3 DR
1333 MHz
1066 MHz
1066 MHz
800 MHz
3
3
DR 1333 MHz
DR 1066 MHz
SR 1333 MHz
DR 1333 MHz
DR 1066 MHz
SR 1333 MHz
DR 1333 MHz
DR 1066 MHz
QR 1066 MHz
—
1
3 mixed
2
1066 MHz
800 MHz
800 MHz
667 MHz
3
3
— *These are the only configurations supported by UDIMMs. All configurations listed in this table
are supported by RDIMMs.
— LVDIMM support is dependent on the ROM version.
— This table is for reference only. It may not be updated to reflect recent changes.
o
800 MHz—The memory bus speed is set to 800 MHz regardless of the quantity of memory modules
installed, unless the table above reflects a slower memory bus speed.
Removal and replacement procedures 64
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: There may be more than one memory bus speed menu option.
DIMMs
To remove the component:
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
5.
6.
Remove the DIMM.
To replace the component, reverse the removal procedure.
Battery replacement
If the server no longer automatically displays the correct date and time, you may need to replace the battery
that provides power to the real-time clock.
WARNING: The computer contains an internal lithium manganese dioxide, a vanadium
pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not
properly handled. To reduce the risk of personal injury:
• Do not attempt to recharge the battery.
• Do not expose the battery to temperatures higher than 60°C (140°F).
• Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.
• Replace only with the spare designated for this product.
Removal and replacement procedures 65
Download from Www.Somanuals.com. All Manuals Search And Download.
To remove the component:
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
If any full-length expansion boards are installed, remove the full-length expansion board shipping
5.
6.
7.
Remove the battery.
To replace the component, reverse the removal procedure.
For more information about battery replacement or proper disposal, contact an authorized reseller or an
authorized service provider.
Systems Insight Display
To remove the component:
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
5.
6.
Disconnect the Systems Insight Display cable.
Removal and replacement procedures 66
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
Remove the Systems Insight Display.
To replace the component, reverse the removal procedure.
Front left bezel
To remove the component:
1.
2.
Extend or remove the server from the rack ("Remove the server from the rack" on page 28, "Extend the
3.
4.
5.
6.
7.
Disconnect the System Insight Display cable from the system board.
Removal and replacement procedures 67
Download from Www.Somanuals.com. All Manuals Search And Download.
8.
Remove the three T-10 Torx screws, and then detach the front bezel.
To replace the component, reverse the removal procedure.
Power supply cage assembly
To remove the component:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Loosen the system board thumbscrews, and then slide the system board assembly forward.
Removal and replacement procedures 68
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Remove the power supply cage assembly.
To replace the component, reverse the removal procedure.
System board
To remove the component:
1.
2.
3.
4.
5.
6.
7.
8.
CAUTION: To prevent damage to the server or expansion boards, power down the server and
remove all AC power cords before removing or installing the PCI riser cage.
9.
Removal and replacement procedures 69
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Using the processor tool, remove the processor from the system board.
CAUTION: To avoid damage to the processor, do not touch the bottom of the processor,
especially the contact area.
15. Disconnect all cables connected to the system board.
16. Remove the retaining screw at the rear of the chassis.
17. Loosen the system board thumbscrews.
19. Remove the failed system board.
To replace the system board:
1.
Install the spare system board.
CAUTION: The pins on the processor socket are very fragile. Any damage to them may require
replacing the system board.
Removal and replacement procedures 71
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Prepare the processor socket on the spare system board:
a. Remove the processor socket protective cover.
b. Open the processor retaining latch and the processor socket retaining bracket.
3.
4.
Install the processor socket cover onto the processor socket of the failed system board.
Install the processor on the spare system board.
IMPORTANT: Be sure the processor remains inside the processor installation tool.
Removal and replacement procedures 72
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
If the processor has separated from the installation tool, carefully re-insert the processor in the tool.
Handle the processor by the edges only, and do not touch the bottom of the processor, especially the
contact area.
6.
The processor fits one way into the socket. Use the alignment guides on the processor and socket to
properly align the processor with the socket. Install the spare processor. THE PINS ON THE SYSTEM
BOARD ARE VERY FRAGILE AND EASILY DAMAGED.
CAUTION: THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. To
avoid damage to the system board:
• Never install or remove a processor without using the processor installation tool.
• Do not touch the processor socket contacts.
• Do not tilt or slide the processor when lowering the processor into the socket.
Removal and replacement procedures 73
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
Press the tabs on the processor tool to release the processor, and then remove the processor tool.
8.
Close the processor socket retaining bracket and the processor locking lever.
CAUTION: Be sure to close the processor socket retaining bracket before closing the processor
locking lever. The lever should close without resistance. Forcing the lever closed can damage the
processor and socket, requiring system board replacement.
9.
Clean the old thermal grease from the heatsink with the alcohol swab. Allow the alcohol to evaporate
before continuing.
Removal and replacement procedures 74
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Apply all the grease to the top of the processor in the following pattern to ensure even distribution.
11. Install the heatsink.
12. Install all components removed from the failed system board.
15. Power up the server.
IMPORTANT: Install all components with the same configuration that was used on the failed
system board.
After you replace the system board, you must re-enter the server serial number and the product ID.
1.
2.
3.
4.
During the server startup sequence, press the F9 key to access RBSU.
Select the Advanced Options menu.
Select Service Options.
Select Serial Number. The following warnings appear:
Removal and replacement procedures 75
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING! WARNING! WARNING! The serial number is loaded into the system during
the manufacturing process and should NOT be modified. This option should only
be used by qualified service personnel. This value should always match the
serial number sticker located on the chassis.
Warning: The serial number should ONLY be modified by qualified personnel.
This value should always match the serial number located on the chassis.
5.
6.
7.
Press the Enter key to clear the warning.
Enter the serial number and press the Enter key.
Select Product ID. The following warning appears:
Warning: The Product ID should ONLY be modified by qualified personnel. This
value should always match the Product ID on the chassis.
8.
9.
Enter the product ID and press the Enter key.
Press the Esc key to close the menu.
10. Press the Esc key to exit RBSU.
11. Press the F10 key to confirm exiting RBSU. The server automatically reboots.
HP Trusted Platform Module
The TPM is not a customer-removable part.
CAUTION: Any attempt to remove an installed TPM from the system board breaks or disfigures
the TPM security rivet. Upon locating a broken or disfigured rivet on an installed TPM,
administrators should consider the system compromised and take appropriate measures to ensure
the integrity of the system data.
If you suspect a TPM board failure, leave the TPM installed and remove the system board. Contact an HP
authorized service provider for a replacement system board and TPM board.
Removal and replacement procedures 76
Download from Www.Somanuals.com. All Manuals Search And Download.
Cabling
SAS hard drive cabling
Connect the SAS power cable from the primary drive cage (drive cage containing drives 1 - 8) to the primary
SAS power connector on the system board.
If a secondary drive cage (drive cage containing drives 9 - 16) is installed, connect a SAS power cable from
the secondary drive cage to the secondary SAS power connector on the system board.
Cabling 77
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostic tools
Troubleshooting resources
The HP ProLiant Servers Troubleshooting Guide provides procedures for resolving common problems and
comprehensive courses of action for fault isolation and identification, error message interpretation, issue
resolution, and software maintenance on ProLiant servers and server blades. This guide includes
problem-specific flowcharts to help you navigate complex troubleshooting processes. To view the guide,
select a language:
•
•
•
•
•
•
•
HP Insight Diagnostics
HP Insight Diagnostics is a proactive server management tool, available in both offline and online versions,
that provides diagnostics and troubleshooting capabilities to assist IT administrators who verify server
installations, troubleshoot problems, and perform repair validation.
HP Insight Diagnostics Offline Edition performs various in-depth system and component testing while the OS
is not running. To run this utility, launch the SmartStart CD.
HP Insight Diagnostics Online Edition is a web-based application that captures system configuration and
other related data needed for effective server management. Available in Microsoft® Windows® and Linux
versions, the utility helps to ensure proper system operation.
For more information or to download the utility, refer to the HP website (http://www.hp.com/servers/diags).
HP Insight Diagnostics survey functionality
HP Insight Diagnostics (on page 79) provides survey functionality that gathers critical hardware and software
information on ProLiant servers.
This functionality supports operating systems that may not be supported by the server. For operating systems
If a significant change occurs between data-gathering intervals, the survey function marks the previous
information and overwrites the survey data files to reflect the latest changes in the configuration.
Diagnostic tools 79
Download from Www.Somanuals.com. All Manuals Search And Download.
Survey functionality is installed with every SmartStart-assisted HP Insight Diagnostics installation, or it can be
installed through the HP PSP.
NOTE: The current version of SmartStart provides the memory spare part numbers for the server.
Integrated Management Log
The IML records hundreds of events and stores them in an easy-to-view form. The IML timestamps each event
with 1-minute granularity.
You can view recorded events in the IML in several ways, including the following:
•
•
•
From within HP SIM
From within Survey Utility
From within operating system-specific IML viewers
o
o
o
For NetWare: IML Viewer (does not apply to HP ProLiant DL980 Servers)
For Windows®: IML Viewer
For Linux: IML Viewer Application
•
•
From within the iLO 3 user interface
For more information, see the Management CD or DVD in the HP Insight Foundation suite for ProLiant.
HP Insight Remote Support software
HP strongly recommends that you install HP Insight Remote Support software to complete the installation or
upgrade of your product and to enable enhanced delivery of your HP Warranty, HP Care Pack Service, or
HP contractual support agreement. HP Insight Remote Support supplements your monitoring 24 x 7 to ensure
maximum system availability by providing intelligent event diagnosis, and automatic, secure submission of
hardware event notifications to HP, which will initiate a fast and accurate resolution, based on your product’s
service level. Notifications may be sent to your authorized HP Channel Partner for on-site service, if
configured and available in your country. The software is available in two variants:
•
HP Insight Remote Support Standard: This software supports server and storage devices and is
optimized for environments with 1–50 servers. Ideal for customers who can benefit from proactive
notification but do not need proactive service delivery and integration with a management platform.
•
HP Insight Remote Support Advanced: This software provides comprehensive remote monitoring and
proactive service support for nearly all HP servers, storage, network, and SAN environments, plus
selected non-HP servers that have a support obligation with HP. It is integrated with HP Systems Insight
Manager. A dedicated server is recommended to host both HP Systems Insight Manager and HP Insight
Remote Support Advanced.
Details for both versions are available on the HP website (http://www.hp.com/go/insightremotesupport).
Select Insight Remote Support from the menu on the right.
Diagnostic tools 80
Download from Www.Somanuals.com. All Manuals Search And Download.
USB support
HP provides both standard USB 2.0 support and legacy USB 2.0 support. Standard support is provided by
the OS through the appropriate USB device drivers. Before the OS loads, HP provides support for USB
devices through legacy USB support, which is enabled by default in the system ROM.
Legacy USB support provides USB functionality in environments where USB support is not available normally.
Specifically, HP provides legacy USB functionality for the following:
•
•
•
•
•
POST
RBSU
Diagnostics
DOS
Operating environments which do not provide native USB support
Diagnostic tools 81
Download from Www.Somanuals.com. All Manuals Search And Download.
Component identification
Front panel components
Item
Description
Quick release levers (2)
Serial number label
Systems Insight Display
Hard drive bays
1
2
3
4
5
6
7
SATA optical drive bay
Video connector
USB connectors (2)
Front panel LEDs and buttons
Item
Description
Status
UID LED button
Blue = Activated
1
Flashing blue = System being remotely managed
Off = Deactivated
Component identification 82
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
Status
Health LED
Green = Normal
2
Flashing amber = System degraded. To identify a component in a
Flashing red = System critical. To identify a component in a critical
Power On/Standby button
and system power LED
Green = System on
3
Flashing green = Waiting for power due to group power capping
Amber = System shut down, but power still applied
Off = Power cord not attached or power supply failure
Rear panel components
Item Description
Color
—
PCI slot 5
1
PCI slot 6
—
2
PCI slot 4
—
3
PCI slot 2
—
4
PCI slot 3
—
5
PCI slot 1
—
6
Power supply 2
Power supply 2 connector
Power supply 1
Power supply 1 connector
USB connectors (2)
Video connector
NIC 1 connector
NIC 2 connector
Mouse connector
Keyboard connector
Serial connector
iLO 3 connector
NIC 3 connector
NIC 4 connector
—
7
—
8
—
9
—
10
11
12
13
14
15
16
17
18
19
20
Black
Blue
—
—
Green
Purple
—
—
—
—
Component identification 83
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel LEDs and buttons
Item Description
Status
Power supply 2
power LED
Green = Normal
Off = System is off or power supply has failed.
1
2
3
Power supply 1
power LED
Green = Normal
Off = System is off or power supply has failed.
UID LED button
Blue = Activated
Flashing blue = System being remotely managed
Off = Deactivated
NIC and iLO 3
activity LED
Green = Network activity
Flashing green = Network activity
Off = No network activity
4
5
NIC and iLO 3 link Green = Network link
LED
Off = No network link
Component identification 84
Download from Www.Somanuals.com. All Manuals Search And Download.
System board components
Item
Description
Processor 2 memory sockets
Front I/O connector
1
2
USB tape connector*
SATA optical drive connector
USB connector
3
4
5
Power supply backplane connector
System maintenance switch
System battery connector
TPM connector
6
7
8
9
NMI jumper
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Primary riser connector
SD card connector
Secondary riser connector
Secondary SAS power connector
Primary SAS power connector
Diagnostics LEDs
Primary SAS data connector
Secondary SAS data connector
SAS cache connector
Fan 1 connector
Processor 1 memory sockets
Fan 2 connector
Fan 3 connector
Component identification 85
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
Fan 4 connector
Processor 1 socket
Fan 5 connector
Processor 2 socket
Fan 6 connector
24
25
26
27
28
*Connect the USB tape power connector to the secondary SAS power connector.
System board switches
System maintenance switch
Position
Default
Function
Off
Off = iLO 3 security is enabled.
On = iLO 3 security is disabled.
S1
Off
Off = System configuration can be changed.
On = System configuration is locked.
S2
Off
Off
Off
Reserved
Reserved
S3
S4
S5
Off = Power-on password is enabled.
On = Power-on password is disabled.
Off
Off = No function
On = ROM reads system configuration as invalid.
S6
When the system maintenance switch position 6 is set to the On position, the system is prepared to erase all
system configuration settings from both CMOS and NVRAM.
CAUTION: Clearing CMOS and/or NVRAM deletes configuration information. There is an
RBSU setting that erases default settings and fixed disk partitions, which causes a loss of data.
Diagnostic LEDs
Position
Position
S8
Function
Diagnostic LEDs
Port 85
S7
Off
Off
Off
On
On
Port 84
Off
iLO 3
NMI functionality
An NMI crash dump enables administrators to create crash dump files when a system is hung and not
responding to traditional debug mechanisms.
Crash dump log analysis is an essential part of diagnosing reliability problems, such as hangs in operating
systems, device drivers, and applications. Many crashes freeze a system, and the only available action for
administrators is to cycle the system power. Resetting the system erases any information that could support
problem analysis, but the NMI feature preserves that information by performing a memory dump before a
hard reset.
Component identification 86
Download from Www.Somanuals.com. All Manuals Search And Download.
To force the OS to invoke the NMI handler and generate a crash dump log, the administrator can do either
of the following:
•
•
Short the NMI jumper pins
Use the iLO Virtual NMI feature
For more information, see the whitepaper on the HP website
DIMM slots
DIMM slots are identified by the numbers 1 through 12.
Component identification 87
Download from Www.Somanuals.com. All Manuals Search And Download.
Systems Insight Display LEDs
Item
Description
Status
NIC LEDs
Off = No link to network
1
Flashing green = Network link and activity
Green = Network link
Power Cap LED
AMP Status LED
Off = Server in standby
Flashing amber = Power cap exceeded
Green = Power cap configured
2
3
Off = Not enabled
Green = Configured and running
Amber = Failure has occurred.
Flashing amber = Memory configuration is not valid.
All other LEDs
Off = Normal
Amber = Failure
--
Systems Insight Display LEDs and health LED
combinations
When the health LED on the front panel illuminates either amber or red, the server is experiencing a health
event. Combinations of illuminated system LEDs and the health LED indicate system status.
Systems Insight Display
LED and color
Health LED color Status
Red
One or more of the following conditions may exist:
Processor (amber)
•
•
•
•
Processor in socket X has failed.
Processor X is not installed in the socket.
Processor X is unsupported.
ROM detects a failed processor during POST.
Amber
Processor in socket X is in a pre-failure condition.
Component identification 88
Download from Www.Somanuals.com. All Manuals Search And Download.
Systems Insight Display
LED and color
Health LED color Status
Red
DIMM in slot X has failed.
DIMM (amber)
Amber
DIMM in slot X is in a pre-failure condition.
Red
One or more DIMMs have failed. Test each bank of DIMMs
by removing all other DIMMs. Isolate the failed DIMM by
replacing each DIMM in a bank with a known working
DIMM.
DIMM (amber)
Amber
Red
The Health Driver has detected a cautionary temperature
level.
Overtemperature (amber)
The server has detected a hardware critical temperature
level.
Amber
Red
One fan is failed or removed.
Fan (amber)
Two or more fans have failed or are missing.
Red
Only one power supply is installed and is in standby.
Power supply (amber)
•
•
Power supply fault
System board fault
Amber
Redundant power supply is installed and only one power
supply is functional.
Power supply (amber)
•
AC power cord not plugged into redundant power
supply
•
Redundant power supply fault
Amber
Power supply mismatch at POST or power supply mismatch
through hot add
Power supply (amber)
Hard drive numbering
•
SFF device bay numbering
Component identification 89
Download from Www.Somanuals.com. All Manuals Search And Download.
•
LFF device bay numbering
SAS and SATA hard drive LEDs
Item
1
Description
Fault/UID LED (amber/blue)
Online LED (green)
2
SAS and SATA hard drive LED combinations
Online/activity
LED (green)
Fault/UID LED
(amber/blue)
Interpretation
Alternating amber
and blue
The drive has failed, or a predictive failure alert has been received
for this drive; it also has been selected by a management
application.
On, off, or flashing
Steadily blue
The drive is operating normally, and it has been selected by a
management application.
On, off, or flashing
Amber, flashing
regularly (1 Hz)
A predictive failure alert has been received for this drive.
Replace the drive as soon as possible.
On
On
Off
The drive is online, but it is not active currently.
Component identification 90
Download from Www.Somanuals.com. All Manuals Search And Download.
Online/activity
LED (green)
Fault/UID LED
(amber/blue)
Interpretation
Amber, flashing
regularly (1 Hz)
Do not remove the drive. Removing a drive may terminate the
current operation and cause data loss.
The drive is part of an array that is undergoing capacity expansion
or stripe migration, but a predictive failure alert has been received
for this drive. To minimize the risk of data loss, do not replace the
drive until the expansion or migration is complete.
Flashing regularly
(1 Hz)
Off
Do not remove the drive. Removing a drive may terminate the
current operation and cause data loss.
The drive is rebuilding, erasing, or it is part of an array that is
undergoing capacity expansion or stripe migration.
Flashing regularly
(1 Hz)
Amber, flashing
regularly (1 Hz)
The drive is active, but a predictive failure alert has been received
for this drive. Replace the drive as soon as possible.
Flashing irregularly
Off
The drive is active, and it is operating normally.
Flashing irregularly
Off
Steadily amber
A critical fault condition has been identified for this drive, and the
controller has placed it offline. Replace the drive as soon as
possible.
Amber, flashing
regularly (1 Hz)
A predictive failure alert has been received for this drive. Replace
the drive as soon as possible.
Off
Off
Off
The drive is offline, a spare, or not configured as part of an array.
PCI riser cage LEDs
CAUTION: To prevent damage to the server or expansion boards, power down the server and
remove all AC power cords before removing or installing the PCI riser cage.
Status
On = AC power is connected.
Off = AC power is disconnected.
Missing = Riser is not installed and power might be connected.
Component identification 91
Download from Www.Somanuals.com. All Manuals Search And Download.
Non-hot-plug PCI riser board slot definitions
Secondary (slot - Primary (slot - PCIe2 riser slot PCIe2 riser slot PCIe2 x16
PCIe2/PCI-X
riser slot
form factor)
form factor)
description
description
riser slot
description
description
1 - FL/FH
2 - HL/FH
3 - HL/FH
PCIe2 x16
(8,4,2,1)
PCIe2 x16
(8,4,2,1)
PCIe2 x16
(16,8,4,2,1)
PCI-X 64 bit/100
MHz
4 - FL/FH
5 - LP
PCIe2 x8 (4,2,1) PCIe2x16
(8,4,2,1)
—
—
PCI-X 64 bit/100
MHz)
PCIe2 x8 (4,2,1) —
PCIe2 x8
(8,4,2,1)
6 - LP
Notes:
•
•
•
"Primary" denotes the risers are installed in the primary riser connector.
"Secondary" denotes the risers are installed in the secondary riser connector.
Installing the risers listed in the table above in either the primary or secondary riser connectors
determines the form factor of the PCI cards supported by those risers.
•
•
FL/FH denotes full-length, full-height. HL/FH denotes half-length, full-height. LP denotes low profile.
The PCIe2 x16 riser supports a maximum power of 225W with an HP power cable. This cable must be
used for PCIe card wattages greater than 75W.
Component identification 92
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery pack LEDs
Item ID Color
Description
Green
System Power LED. This LED glows steadily when the system
is powered up and 12 V system power is available. This
power supply is used to maintain the battery charge and
provide supplementary power to the cache microcontroller.
1
Green
Auxiliary Power LED. This LED glows steadily when 3.3V
auxiliary voltage is detected. The auxiliary voltage is used
to preserve BBWC data and is available any time that the
system power cords are connected to a power supply.
2
Amber
Green
Battery Health LED. To interpret the illumination patterns of
this LED, see the following table.
3
4
BBWC Status LED. To interpret the illumination patterns of
this LED, see the following table.
LED3 pattern
LED4 pattern
Interpretation
One blink every
two seconds
The system is powered down, and the cache contains data that has not
yet been written to the drives. Restore system power as soon as
possible to prevent data loss.
—
Data preservation time is extended any time that 3.3 V auxiliary
power is available, as indicated by LED 2. In the absence of auxiliary
power, battery power alone preserves the data. A fully-charged
battery can normally preserve data for at least two days.
The battery lifetime also depends on the cache module size. For further
information, refer to the controller QuickSpecs on the HP website
Double blink, then The cache microcontroller is waiting for the host controller to
pause communicate.
—
Component identification 93
Download from Www.Somanuals.com. All Manuals Search And Download.
LED3 pattern
LED4 pattern
Interpretation
One blink per
second
The battery pack is below the minimum charge level and is being
charged. Features that require a battery (such as write cache, capacity
expansion, stripe size migration, and RAID migration) are temporarily
unavailable until charging is complete. The recharge process takes
between 15 minutes and two hours, depending on the initial capacity
of the battery.
—
Steady glow
Off
The battery pack is fully charged, and posted write data is stored in the
cache.
—
—
The battery pack is fully charged, and there is no posted write data in
the cache.
One blink per
second
An alternating green and amber blink pattern indicates that the cache
microcontroller is executing from within its boot loader and receiving
new flash code from the host controller.
One blink per
second
—
There is a short circuit across the battery terminals or within the battery
pack. BBWC features are disabled until the battery pack is replaced.
The life expectancy of a battery pack is typically more than three
years.
Steady glow
—
There is an open circuit across the battery terminals or within the
battery pack. BBWC features are disabled until the battery pack is
replaced. The life expectancy of a battery pack is typically more than
three years.
One blink per
second
FBWC module LEDs
The FBWC module has two single-color LEDs (green and amber). The LEDs are duplicated on the reverse side
of the cache module to facilitate status viewing.
Green LED
Amber LED
Interpretation
On
On
Off
Off
A backup is in progress.
Off
A restore is in progress.
Flashing (1 Hz)
Flashing (1 Hz)
On
The capacitor pack is charging.
The capacitor pack has completed charging.
Component identification 94
Download from Www.Somanuals.com. All Manuals Search And Download.
Green LED
Amber LED
Interpretation
Flashing (2 Hz)
Alternating with
green LED
One of the following conditions exists:
Flashing (2 Hz)
Alternating with
amber LED
•
•
The charging process has timed out.
The capacitor pack is not connected.
On
Off
The flash code image failed to load.
The flash code is corrupt.
On
Off
Hot-plug fans
CAUTION: To avoid damage to server components, fan blanks must be installed in fan bays 5
and 6 in a single-processor configuration.
Component identification 95
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Environmental specifications
Specification
Value
Temperature range*
Operating
10°C to 35°C (50°F to 95°F)
-30°C to 50°C (-22°F to 122°F)
-30°C to 60°C (-22°F to 140°F)
28°C (82.4°F)
Shipping
Storage
Maximum wet bulb
temperature
Relative humidity
(noncondensing)**
10% to 90%
5% to 95%
Operating
Non-operating
* All temperature ratings shown are for sea level. An altitude derating of 1°C per 300 m (1.8°F per 1,000 ft) to 3048
m (10,000 ft) is applicable. No direct sunlight allowed.
** Storage maximum humidity of 95% is based on a maximum temperature of 45°C (113°F). Altitude maximum for
storage corresponds to a pressure minimum of 70 KPa.
Server specifications
Specification
Value
8.85 cm (3.45 in)
69.20 cm (27.25 in)
44.54 cm (17.54 in)
27.27 kg (60.12 lb)
21.36 kg (47.10 lb)
Height
Depth
Width
Weight (maximum)
Weight (no drives installed)
Input requirements*
100 to 132 VAC
200 to 240 VAC
Rated input voltage
50 Hz to 60 Hz
Rated input frequency
Rated input current
8 A at 100 VAC
3.9 A at 200 VAC
785 W at 100V AC input
765 W at 200V AC input
Rated input power
BTUs per hour
2677 at 100V to 120V AC input
2609 at 200V to 240V AC input
Power supply output
For more information, see “Power
supply specifications (on page
Rated steady-state power
Specifications 96
Download from Www.Somanuals.com. All Manuals Search And Download.
For more information, see “Power
supply specifications (on page
Rated peak power
*The system input requirements are based on measurements using hardware available at the publication of this
document. For updated information, see the HP website (http://www.hp.com/go/proliant-energy-efficient).
Power supply specifications
The following specifications provide information on the parameters of the power supplies as they were
designed. For more information on configuring power for a specific server, see the HP website
Depending on installed options, the server is configured with one of the following power supplies:
•
HP ProLiant 460 W Power Supply
Specification
Value
Input requirements
100V to 120V AC
200V to 240V AC
Rated input voltage
50Hz to 60Hz
Rated input frequency
Rated input current
5.5A at 100V AC
2.6A at 200V AC
526 W at 100V AC input
505 W at 200V AC input
Rated input power
BTUs per hour
1794 at 100V AC input
1725 at 200V AC input
Power supply output
460 W at 100V to 120V AC input
460 W at 200V to 240V AC input
Rated steady-state power
460 W at 100V to 120V AC input
460 W at 200V to 240V AC input
Rated peak power
•
HP ProLiant 750 W Power Supply
Specification
Value
Input requirements
100V to 120V AC
200V to 240V AC
Rated input voltage
50Hz to 60Hz
Rated input frequency
Rated input current
8.9A at 100V AC
4.3A at 200V AC
857 W at 100V AC input
824 W at 200V AC input
Rated input power
BTUs per hour
2925 at 100V AC input
2812 at 200V AC input
Power supply output
750 W at 100V to 120V AC input
750 W at 200V to 240V AC input
Rated steady-state power
Specifications 97
Download from Www.Somanuals.com. All Manuals Search And Download.
750 W at 100V to 120V AC input
750 W at 200V to 240V AC input
Rated peak power
•
HP ProLiant 1200 W Power Supply
Specification
Value
Input requirements
100V to 120V AC
200V to 240V AC
Rated input voltage
50 Hz to 60 Hz
Rated input frequency
Rated input current
9.3A at 100V AC
6.6A at 200V AC
912 W at 100V AC input
1294 W at 200V AC input
Rated input power
BTUs per hour
3110 at 100V AC input
4413 at 200V input
Power supply output
800 W at 100V AC input
900 W at 120V AC input
1200 W at 200V to 240V AC
input
Rated steady-state power
800 W at 100V AC input
900 W at 120V AC input
1200 W at 200V to 240V AC
input
Rated peak power
•
HP ProLiant 1200 W DC Power Supply
Specification
Value
Input requirements
-36V to -72V DC
-48V DC, nominal input
Rated input voltage
Not applicable
Rated input frequency
Rated input current
38A at -36V DC
19A at -72V DC
28A at -48V DC, nominal input
1380 W at -36V DC input
1365 W at -72V DC input
1350 W at -48V DC, nominal
input
Rated input power
BTUs per hour
4713 at -36V DC input
4662 at -72V DC input
4610 at -48V DC, nominal input
Power supply output
Rated steady-state power
Rated peak power
1200 W
1200 W
Specifications 98
Download from Www.Somanuals.com. All Manuals Search And Download.
Hot-plug power supply calculations
For hot-plug power supply specifications and calculators to determine electrical and heat loading for the
CD-ROM drive specifications
Specification
Value
CD-ROM (modes 1 and 2); mixed mode (audio and data combined); CD-DA; Photo
CD (single/multiple-session), CD-XA ready; CDi ready
Disk formats
550 MB (mode 1, 12 cm)
640 MB (mode 2, 12 cm)
Capacity
2368, 2352 bytes (mode 0)
Block size
2352, 2340, 2336, 2048 bytes (mode 1)
2352, 2340, 2336, 2048 bytes (mode 2)
Dimensions
Height
12.7 mm (0.50 in)
132.08 mm (5.20 in)
132.08 mm (5.20 in)
0.34 kg (0.75 lb)
Depth
Width
Weight
Data transfer rate
Sustained
150 KB/s (sustained 1X), 1500/3600 KB/s (10X to 24X)
16.6 MB/s
Burst
Access times (typical)
Full stroke
300 ms
140 ms
Random
12 cm, 8 cm (4.70 in, 3.15 in)
1.2 mm (0.05 in)
1.6 µm (6.3 × 10-7 in)
128 KB
Diameter
Thickness
Track pitch
Cache/buffer
Startup time
Stop time
< 10 s
< 5 s (single); < 30 s (multisession)
Laser parameters
Type
Semiconductor laser GaAs
700 ± 25 nm
Wave length
Divergence angle
Output power
Operating conditions
Temperature
Humidity
53.5° ± 1.5°
0.14 mW
5°C to 55°C (41°F to 131°F)
10% to 80%
Specifications 99
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD-ROM drive specifications
Specification
Value
DVD (single and double layer), DVD-5, DVD-9, DVD-10, DVD-R, CD-ROM Mode 1
& 2, CD-DA, CD-XA (Mode 2, Form 1 & 2), CD-I (Mode 2, Form 1 & 2), CD-I ready,
CD-Bridge, CD-R, PhotoCD (single and multi-session)
Disk formats
4.7 GB (DVD-5), 8.5 GB (DVD-9), 9.4 GB (DVD10), 550 Mb (Mode 1, 12 cm),
640 Mb (Mode 2, 12 cm), 180 Mb (8 cm)
Capacity
2352 bytes (mode 0)
Block size
2352, 2340, 2336, 2048 bytes (mode 1)
2352, 2340, 2336, 2048 bytes (mode 2)
2048 bytes (DVD)
Dimensions
Height
12.7 mm (0.50 in)
132.08 mm (5.20 in)
132.08 mm (5.20 in)
0.34 kg (0.75 lb)
Depth
Width
Weight
Data transfer rate
Sustained
4463 - 10,800 KB/s (8X CAV DVD mode), 150 KB/s (sustained 1X CD-ROM),
1552 3600 KB/s (24X CAV CD-ROM)
16.6 MB/s with DMA support
Burst
Access times (typical)
Full stroke
<200 ms CD
<300 ms DVD
<110 ms CD
<180 ms DVD
Random
12 cm, 8 cm (4.70 in, 3.15 in)
Diameter
Thickness
Track pitch
1.2 mm (0.05 in)
0.74 µm (3.15 × 10-7 in) DVD-ROM
1.6 µm (6.3 × 10-7 in) CD-ROM
128 KB
Cache/buffer
Startup time
Stop time
< 15 s
< 5 s (single); < 30 s (multisession)
Laser parameters
Type
Semiconductor laser GaAs
700 ± 25 nm
Wave length
Divergence angle
Output power
Operating conditions
Temperature
Humidity
53.5° ± 1.5°
0.14 mW
5°C to 55°C (41°F to 131°F)
10% to 80%
SAS and SATA hard drive specifications
Item
36-GB SAS drive
72-GB SAS drive
60-GB SATA drive
36,420 MB
73,408 MB
60,022 MB
Capacity
Specifications 100
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
36-GB SAS drive
72-GB SAS drive
60-GB SATA drive
15 mm
15 mm
9 mm
Height
SAS
SAS
Serial ATA
Interface
3 GB/sec
3 GB/sec
1.5 GB/sec
Transfer rate
10,000 rpm
10,000 rpm
5,400 rpm
Rotational
speed
512
512
512
Bytes per sector
71,132,960
143,374,737
117,231,408
Logical blocks
10°C to 35°C
(50°F to 95°F)
10°C to 35°C
(50°F to 95°F)
10°C to 35°C
(50°F to 95°F)
Operating
temperature
Specifications 101
Download from Www.Somanuals.com. All Manuals Search And Download.
Acronyms and abbreviations
ABEND
abnormal end
ASR
Automatic Server Recovery
BBWC
battery-backed write cache
DDR
double data rate
FBWC
flash-backed write cache
iLO 3
Integrated Lights-Out 3
IML
Integrated Management Log
NMI
non-maskable interrupt
NVRAM
non-volatile memory
ORCA
Option ROM Configuration for Arrays
PCIe
peripheral component interconnect express
PCI-X
peripheral component interconnect extended
Acronyms and abbreviations 102
Download from Www.Somanuals.com. All Manuals Search And Download.
POST
Power-On Self Test
RBSU
ROM-Based Setup Utility
RDP
Rapid Deployment Pack
SAS
serial attached SCSI
SATA
serial ATA
TPM
trusted platform module
UID
unit identification
USB
universal serial bus
Acronyms and abbreviations 103
Download from Www.Somanuals.com. All Manuals Search And Download.
|