User Guide
hp StorageWorks
Network Storage Router N1200
Product Version: 2.0
Second Edition (November 2003)
Part Number: 282011-002
282011-002
The HP StorageWorks Network Storage Router provides bidirectional connectivity in either a
Fibre Channel Switched Fabric or a Fibre Channel Arbitrated Loop environment, supporting
Fibre Channel and SCSI devices.
This user guide provides instructional information for configuring the network storage router.
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Text Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Equipment Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Rack Stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
HP Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
HP Storage Website . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
HP Authorized Reseller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
External Features Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Serial Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Ethernet Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Fibre Channel Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SCSI Buses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Fibre Channel to SCSI Protocol Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SCSI to Fibre Channel Protocol Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
LAN-free Backup and Restore. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Server-Free Data Movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Router Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Operating Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Network Storage Router N1200 User Guide
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Shipping and Storing Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Router Default Ethernet Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
UI Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Visual Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
FTP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SNMP (SNMP is not supported) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Common Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Controller LUN Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SCSI Bus Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Fibre Channel Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Fibre Channel Arbitrated Loop Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Fibre Channel Switched Fabric Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Discovery Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Host Device Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Logical Unit Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Buffered Tape Writes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3 Visual Manager User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Visual Manager Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Visual Manager Best Practices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Serial Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Active Fabric Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
User Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Real-Time Clock Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Reset Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Fibre Channel Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
SCSI Bus Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Discovery Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Mapping Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Common Fibre Channel and SCSI Mapping Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
4
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Fibre Channel Mapping Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
SCSI Mapping Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Statistics Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Utilities Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
FTP Utility Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Trace Settings Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Current, Previous, and Last Assert Trace Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Clear Current Traces and Clear Assert Traces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Event Log Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Event Log Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Clear Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Report Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Reboot Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Telnet UI Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Serial UI Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Power up Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Serial/Telnet UI Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Baud Rate Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Ethernet Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Fibre Channel Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Parallel SCSI Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Device Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Changing to the Next Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Selecting the Current Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Viewing the Current Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Creating a New Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Removing the Current Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Editing the Current Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Cloning the Current Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Editing the Host List for the Current Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Displaying the Entire Device List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Trace and Event Settings Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Configuring Trace Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Configuring Event Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Real-Time Clock Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Active Fabric Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Network Storage Router N1200 User Guide
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Save Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Restore Last Saved Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Reset and Save Configuration to Factory Defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
System Utility Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
System Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Event Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Trace Dump Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Saving Copies of the Trace Buffers using FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Reboot Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Download New Firmware Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Access the FTP UI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Backup and Restore Configuration Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Backing up the Router Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Restoring the Router Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Copy Trace Buffers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Upgrade Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Basic Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Verifying SCSI Bus Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Verifying Fibre Channel Port Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Verifying SCSI Devices in Windows NT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Verifying the Router Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Verifying Mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Verifying Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Verifying the Host Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Verifying HBA Device Driver Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Verifying Serial Port Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Verifying PRLI Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
A Serial and Ethernet Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
RJ-11 Serial Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
RJ-45 Ethernet Cable Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
B Controller LUN Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
General Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
6
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Report LUNs Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Inquiry Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Copy Manager Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Extended Copy Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Receive Copy Results Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Mode Sense (6) and Mode Sense (10) Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
SCC (SCSI Controller Command) Addressing Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Auto Assigned Addressing Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Indexed Addressing Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Regulatory Compliance Identification Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Federal Communications Commission Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Class A Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Class B Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Declaration of Conformity, United States Only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Power Cords. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Canadian Notice (Avis Canadien) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Class A Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Class B Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
European Union Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Japanese Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
BSMI Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Laser Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Laser Safety Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Compliance with CDRH Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Compliance with International Regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Laser Product Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Laser Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
E
Electrostatic Discharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185
Grounding Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187
Network Storage Router N1200 User Guide
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
8
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
About This
Guide
About this Guide
About this Guide
F
■
Install the Network Storage Router
■
About this Guide topics include:
■
■
■
■
Overview, page 10
Conventions, page 11
Rack Stability, page 14
Getting Help, page 15
Network Storage Router N1200 User Guide
9
Download from Www.Somanuals.com. All Manuals Search And Download.
About this Guide
Overview
This section covers the following topics:
■
■
■
Intended Audience
Prerequisites
Related Documentation
Intended Audience
This guide is intended for administrators with a moderate knowledge level about
network environments
Prerequisites
Before you install this product, make sure you consider the items below.
■
■
■
Knowledge of operation system
Knowledge of related hardware/software
Previous version of the product/firmware
Related Documentation
In addition to this guide, HP provides corresponding information:
■
Fibre Channel Physical and Signaling Interface (FC-PH), ANSI
X3T9.3/Project 755D/Rev. 4.3, Contact: Global Engineering, 1-800-854-7179
■
■
■
Fibre Channel Protocol for SCSI (FCP) Revision 12
Fibre Channel Private Loop Direct Attach (FC-PLDA)
Fibre Channel Arbitrated Loop (FC-AL), ANSI X3T11/Project
960D/Revision 4.54, Contact: Globe Engineering, 1-800-854-7179
■
■
Gigabit Interface Converter (GBIC), Small Form Factor. SFF-8053,
Revision 5.X
Common FC-PH Feature Sets Profiles, Fibre Channel Systems Initiative,
FCSI-101 Revision 3.1
■
■
FCSI IP Profile, Fibre Channel System Initiative, FCSI-202-Revision 2.1
10
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
About this Guide
Conventions
Conventions consist of the following:
■
■
■
Document Conventions
Text Symbols
Equipment Symbols
Document Conventions
The document conventions included in Table 1 apply in most cases.
Table 1: Document Conventions
Element
Convention
Cross-reference links
Figure 1
Key and field names, menu items,
buttons, and dialog box titles
Bold
File names, application names, and text
emphasis
Italics
User input, command and directory
names, and system responses (output
and messages)
Monospace font
COMMAND NAMES are uppercase
monospace font unless they are case
sensitive
Variables
<monospace, italic font>
Website addresses
Underlined sans serif font text:
http://www.hp.com
Text Symbols
The following symbols may be found in the text of this guide. They have the
following meanings.
WARNING: Text set off in this manner indicates that failure to follow
directions in the warning could result in bodily harm or death.
Network Storage Router N1200 User Guide
11
Download from Www.Somanuals.com. All Manuals Search And Download.
About this Guide
Caution: Text set off in this manner indicates that failure to follow directions
could result in damage to equipment or data.
Note: Text set off in this manner presents commentary, sidelights, or interesting points
of information.
Equipment Symbols
The following equipment symbols may be found on hardware for which this guide
pertains. They have the following meanings.
Any enclosed surface or area of the equipment marked with these
symbols indicates the presence of electrical shock hazards. Enclosed
area contains no operator serviceable parts.
WARNING: To reduce the risk of personal safety from electrical shock
hazards, do not open this enclosure.
Any RJ-45 receptacle marked with these symbols indicates a network
interface connection.
WARNING: To reduce the risk of electrical shock, fire, or damage to the
equipment, do not plug telephone or telecommunications connectors
into this receptacle.
Any surface or area of the equipment marked with these symbols
indicates the presence of a hot surface or hot component. Contact with
this surface could result in injury.
WARNING: To reduce the risk of personal safety from a hot
component, allow the surface to cool before touching.
12
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
About this Guide
Power supplies or systems marked with these symbols indicate the
presence of multiple sources of power.
WARNING: To reduce the risk of personal safety from electrical
shock, remove all power cords to completely disconnect power
from the power supplies and systems.
Any product or assembly marked with these symbols indicates that the
component exceeds the recommended weight for one individual to
handle safely.
WARNING: To reduce the risk of personal safety or damage to the
equipment, observe local occupational health and safety requirements
and guidelines for manually handling material.
Network Storage Router N1200 User Guide
13
Download from Www.Somanuals.com. All Manuals Search And Download.
About this Guide
Rack Stability
Rack stability protects personal and equipment.
WARNING: To reduce the risk of personal safety or damage to the
equipment, be sure that:
■ The leveling jacks are extended to the floor.
■ The full weight of the rack rests on the leveling jacks.
■ In single rack installations, the stabilizing feet are attached to the rack.
■ In multiple rack installations, the racks are coupled.
■ Only one rack component is extended at any time. A rack may become
unstable if more than one rack component is extended for any reason.
14
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
About this Guide
Getting Help
If you still have a question after reading this guide, contact an HP authorized
service provider or access our website: http://www.hp.com
.
HP Technical Support
In North America, call technical support at 1-800-652-6672, available 24 hours a
day, 7 days a week.
Note: For continuous quality improvement, calls may be recorded or monitored.
Outside North America, call technical support at the nearest location. Telephone
numbers for worldwide technical support are listed on the HP website under
support: http://www.hp.com/support
.
Be sure to have the following information available before calling:
■
■
■
■
■
■
Technical support registration number (if applicable)
Product serial numbers
Product model names and numbers
Applicable error messages
Operating system type and revision level
Detailed, specific questions
HP Storage Website
The HP website has the latest information on this product, as well as the latest
appropriate product or solution.
HP Authorized Reseller
For the name of your nearest HP authorized reseller:
In the United States, call 1-800-345-1518
In Canada, call 1-800-263-5868
■
Network Storage Router N1200 User Guide
15
Download from Www.Somanuals.com. All Manuals Search And Download.
About this Guide
■
Elsewhere, see the HP website for locations and telephone numbers:
.
16
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
1
connectivity for Narrow/Wide Fast/Ultra-3 SCSI buses in either a Fibre Channel
Switched Fabric (FC-SW) or a Fibre Channel Arbitrated Loop (FC-AL)
environment.
This chapter explains the following:
■
External Features Overview, page 18
— Power Indicator
— Serial Port
— Ethernet Port
— Fibre Channel Port
— SCSI Buses
■
Functional Overview, page 21
— SCSI to Fibre Channel Protocol Process
— LAN-free Backup and Restore
— Server-free Data Movement
Router Specifications, page 26
— Operating Environmental Requirements
— Shipping and Storing Environmental Requirements
— Power Requirements
■
Network Storage Router N1200 User Guide
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
External Features Overview
Figure 1 and Figure 2 illustrate the panel view of the router.
Figure 1: Router illustration
Item
Description
Power connector
1
I/O panel
2
Figure 2: Router I/O panel
Item
I/O Panel
Power LED
1
Serial port, 6 pin RJ-11, RS-232
2
3
4
5
6
10/100 TX Ethernet port
Fibre Channel port
LVD SCSI Port 0
LVD SCSI Port 1
18
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Power Indicator
The router has one power LED.
Power indicator LED definition:
Green - Power has been applied to this module
Yellow - Power-On-Self-Test (POST) in process or processor problems
Serial Port
The router is equipped with one serial port. See Figure 2 on page 18 for the
location of the serial port.
The serial port can be used to access the Serial/Telnet user interface, which is used
to locally manage and configure the router.
Table 2: Serial Port Configuration
BAUD Rate
Autobaud, 9600, 19200, 38400, 57600, 115200
Data Bits
8
Stop Bit
1
Parity
None
Flow Control
XON/XOFF
Ethernet Port
One Ethernet port with an LED indicator is included in the router. See Figure 2 on
page 18 for the location of the Ethernet port.
Ethernet port LED definition:
Activity - Port activity
Link - Valid Ethernet link
Network Storage Router N1200 User Guide
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Fibre Channel Port
One Fibre Channel port with LED indicators is included in the router.
See Figure 2 on page 18 for the location of the Fibre Channel port.
Fibre Channel LED definition:
Green (ACT) - Fibre Channel port activity
Green (LINK) - Valid Fibre Channel link
SCSI Buses
Two SCSI buses with LED indicators are included in the router. See Figure 2 on
page 18 for the location of the SCSI buses.
SCSI bus LED definition:
Green - SCSI bus activity on corresponding port
20
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Functional Overview
The router translates the Fibre Channel Protocol (FCP) to and from the SCSI
Protocol. It transfers commands, data, and status information to and from Fibre
Channel controllers and SCSI devices.
Supported devices include:
■
■
■
■
Initiator Devices – Fibre Channel and SCSI hosts
Direct Access Devices – RAID Controllers, disk drives, JBODs
Sequential Access Devices – Tape drives
Changer Devices – Tape and Magneto-Optical Libraries
The router provides multiple Fibre Channel to SCSI I/O configurations. A sample
configuration is illustrated in Figure 3.
Figure 3: Example configuration
SCSI
Tape
Drives
SCSI
Tape
Libraries
Fibre
Channel
LVD/SE SCSl
Link/
Act
0
1
StorageWorks
Router
Pwr.
Serial
Ethernet
FC Host
SCSI
Tape
Libraries
SCSI
Tape
Drives
Fibre Channel
SCSI
Network Storage Router N1200 User Guide
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Fibre Channel to SCSI Protocol Process
This section describes the steps the router uses to convert Fibre Channel host
protocol to SCSI device protocol (see Figure 4).
Figure 4: Converting Fibre Channel to SCSI process
FC Host
1
StorageWorks Router
FC Host
Hub or Switch
2
FC Host
FC Controller
3
4
5
SCSI Controller
SCSI Device SCSI Device SCSI Device
SCSI Device SCSI Device SCSI Device
SCSI Controller
Fibre Channel
SCSI
Table 3: Converting Fibre Channel to SCSI process description
Item
Description
1
2
3
4
5
A Fibre Channel host issues an encapsulated FCP protocol command
packet to the router.
The router Fibre Channel controller interprets the Fibre Channel
information and places the packet in buffer memory.
The router interprets the Fibre Channel information packet and
programs the router SCSI controller to process the transaction.
The router SCSI controller sends the command to the SCSI device
(target).
The SCSI target interprets the command and executes it.
22
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
SCSI to Fibre Channel Protocol Process
In this example, a SCSI host (initiator) on the SCSI bus issues commands and the
information is passed through the router to a target on the Fibre Channel Storage
Area Network (FC-SAN). Figure 5 is an illustration of the process and defines
each step.
Figure 5: Converting SCSI to Fibre Channel protocol process
FC Device
5
StorageWorks Router
Hub or Switch
SCSI Host
4
3
FC Controller
2
FC Device
SCSI Controller
1
Fibre Channel
SCSI
Table 4: Converting SCSI to Fibre Channel protocol process description
Item
Description
1
A SCSI host issues a command to the router.
2
The SCSI controller in the router interprets the command and places it in
buffer memory.
3
4
5
The router processor interprets data and programs the router Fibre
Channel controller to process the transaction.
The router Fibre Channel controller translates data into an FCP protocol
packet and sends it to the Fibre Channel target.
The Fibre Channel target interprets the FCP protocol packet and executes
Network Storage Router N1200 User Guide
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
LAN-free Backup and Restore
The router can enable LAN-free backup/restore to allow the bulk of data traffic to
be moved from the LAN to the storage area network (SAN) (see Figure 6).
Figure 6: LAN-free backup and restore
Fibre Channel
ETHERNET
SCSI TAPE
UNIT
SCSI
DATA MOVEMENT
SCSI TAPE
UNIT
StorageWorks
Router
Fibre
Channel
Link/
Act
LVD/SE SCSl
0
FIBRE CHANNEL
DISK
Pwr.
1
Serial
Ethernet
Fibre
Channel
Link/
Act
LVD/SE SCSl
0
1
Pwr.
Serial
Ethernet
StorageWorks
Router
SAN
SERVER
SERVER
SERVER
SERVER
LAN
24
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Server-Free Data Movement
Used with server-free application software, Copy Manager allows the server to off
load data movement to the router and free up server resources (see Figure 7).
Figure 7: Server-free data movement
Fibre Channel
ETHERNET
SCSI
COMMAND
SCSI TAPE
DATA MOVEMENT
UNIT
SCSI TAPE
UNIT
Fibre
Channel
Link/
Act
LVD/SE SCSl
StorageWorks
Router
0
1
Pwr.
Serial
Ethernet
FIBRE CHANNEL
DISK
Fibre
Channel
Link/
Act
LVD/SE SCSl
0
1
Pwr.
Serial
Ethernet
StorageWorks
Router
SAN
SERVER
SERVER
SERVER
SERVER
LAN
Note: The router implementation of Extended Copy does not support SDMP protocol.
Note: Copy Manager can perform simultaneous Extended Copy commands.
Note: Server-free backup can be activated using the Active Fabric Configuration Menu
option. When activated, the router is enabled for both server-free and LAN-free
capabilities. When deactivated, only LAN-free capabilities are supported.
Network Storage Router N1200 User Guide
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Note: The router implementation of the Extended Copy command is available to
application programmers. See Appendix B, “Controller LUN Commands” on page 161
for additional information.
Router Specifications
This section lists the environmental requirements of the router.
Operating Environmental Requirements
■
Temperature: 0 to 50°C
■
Relative Humidity: 5 to 80% (non-condensing)
Shipping and Storing Environmental Requirements
■
Temperature: -40 to +55°C
■
Relative Humidity: 0 to 92% (non-condensing)
Power Requirements
■
VAC: 100 - 240 (auto sensing)
■
50/60 Hz, 2.0 Amps (each power supply)
26
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Overview
2
using several user interfaces (UI). Each UI is introduced in this chapter, along
Included are:
■
■
■
Router Default Ethernet Settings, page 28
UI Overview, page 29
Common Configuration Settings, page 31
— Controller LUN Commands
— SCSI Bus Configuration
— Fibre Channel Port Configuration
— Fibre Channel Arbitrated Loop Configuration
— Fibre Channel Switched Fabric Configuration
— Discovery Mode
— Host Device Configuration
— Logical Unit Management
— Buffered Tape Writes
Note: Before attempting to configure the router, a basic understanding of Fibre Channel and
SCSI devices is recommended. For information on SCSI standards, refer to publications from the
X3T10 committee of ANSI (American National Standards Institute). For information on Fibre
Channel standards, refer to publications from the X3T11 committee of ANSI. For those who are
interested in purchasing approved American National Standards and Technical Reports, contact
Network Storage Router N1200 User Guide
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Overview
Router Default Ethernet Settings
Some of the basic factory default values are:
IP address: http://1.1.1.1/
Subnet mask: 255.255.255.0
■
■
■
■
■
Gateway address: 0.0.0.0
User name: root
Password: password
HP recommends that you change these values from the defaults.
All settings within the router configuration are preset with default values. These
values are set to allow the router to be installed into most HP environments with
little or no configuration changes.
After changing the basic default values listed above, carefully consider any
additional configuration changes.
After the initial configuration of the router is established, HP recommends
backing up the configuration to an external file. If needed, during a recovery
process, this file can then be restored back onto the router.
28
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Overview
UI Overview
The router supports the following user interfaces:
■
■
■
■
Visual Manager, page 29
Serial, page 29
Telnet, page 29
FTP, page 29
Visual Manager
Visual Manager lets you view and change router configuration from any standard
Web browser. Information is dynamically generated in an HTML format so that
any web browser can access it.
Unless the default values are used, the 10/100BaseT Ethernet port must be
configured using the serial port with an appropriate IP address, subnet mask, and
gateway prior to use.
For complete information on accessing and using Visual Manager, see “Visual
Manager User Interface” on page 37.
Serial
Telnet
The serial port allows for configuration of device characteristics from a terminal
or terminal emulator. Multiple serial connections cannot be run at the same time.
For complete information on accessing and using the Serial UI, see “Serial/Telnet
User Interface” on page 87.
From most Microsoft® Windows® 9x, Windows NT®, and Windows 2000®
systems, users can start a Telnet session from the DOS (command) shell after the
IP address has been set.
For complete information on accessing and using the Telnet UI, see “Serial/Telnet
User Interface” on page 87.
FTP
The router supports the use of the FTP UI to perform several copy procedures
using the putand the getcommands.
Network Storage Router N1200 User Guide
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Overview
Common Configuration Settings
To provide connectivity between hosts and devices, the router must establish an
address on each connected Fibre Channel network and SCSI bus. The following
paragraphs discuss configuration settings that are commonly modified and are
available in the Visual Manager UI and the Serial/Telnet UI. For procedural
information on accessing and changing these settings, see “Visual Manager User
Interface” on page 37 and “Serial/Telnet User Interface” on page 87.
Controller LUN Commands
The router supports a set of SCSI-3 commands that can be received as FCP
commands over the Fibre Channel port. These commands provide support for
value added features such as Extended Copy. When using these commands, they
must be sent to the Controller LUN. For more information, see Appendix B,
“Controller LUN Commands” on page 161.
SCSI Bus Configuration
The router can appear on a SCSI bus as a pair of initiators. The primary Initiator
ID can be set to any valid SCSI address (0-15) and is used for most traffic. The
alternate Initiator ID can also be set to any valid SCSI address (0-15) and is for
use with high priority traffic. The Initiator IDs (primary and alternate) should not
be set to the same SCSI address and no other devices on the SCSI bus may use
either of these SCSI addresses.
The router can also appear as one or more Target ID on a SCSI bus. By default, no
Target IDs are set up.
The router provides the capability to reset SCSI buses during the router boot
cycle. This allows devices on a SCSI bus to be in a known state. The reset option
can be enabled/disabled during configuration of the router. The SCSI bus reset
feature is enabled in the default configuration but should be disabled for
configurations using multiple initiators, tape changers or other devices that have
long reset cycles, or for environments that are adversely affected by bus resets.
The router negotiates the maximum values for transfer rates and bandwidth on a
SCSI bus. If an attached SCSI device does not allow the full rates, the router will
use the best rates it can negotiate for that device. Because negotiation is on a
device-specific basis, the router can support a mix of SCSI device types on the
same SCSI bus.
Network Storage Router N1200 User Guide
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Overview
Fibre Channel Port Configuration
By default, the configuration of the Fibre Channel ports is set to N_Port, forcing
the router to configure as an Arbitrated Loop.
Note: By default, the Fibre Channel port speed is set to 1 Gbps. Changes to the Fibre Channel
port speed must be manually set, such as for 2 Gbps. If set incorrectly and the router is plugged
into a Loop or Fabric, the unit may receive framing errors because of the incorrect Fibre
Channel link speed.
Fibre Channel Arbitrated Loop Configuration
On a Fibre Channel Arbitrated Loop, each device appears as an Arbitrated Loop
Physical Address (AL_PA). To obtain an AL_PA, two methods can be used:
■
Soft Addressing
Hard Addressing
■
Soft addressing is the default setting.
Soft Addressing
During soft addressing, the router automatically acquires the first available loop
address, starting from 01 and moving up to EF. The router may participate on the
Fibre Channel loop as long as there is at least one address available on the loop
connected to the router. Fibre Channel supports up to 126 devices on an
Arbitrated Loop.
Hard Addressing
During hard addressing, the router attempts to acquire the AL_PA value specified
in the configuration settings. If the desired address is not available at loop
initialization time, the router negotiates the next available soft address. This
allows both the loop and the router to continue to operate.
Hard addressing is recommended for Fibre Channel Arbitrated Loop
environments where it is important that the Fibre Channel device addresses do not
change. Device address changes can affect the mapping represented by the host
operating system to the application, and have adverse effects. An example is tape
library installation, where the application configuration requires fixed device
identification for proper operation.
32
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Overview
Fibre Channel Switched Fabric Configuration
When connected to a Fibre Channel switch, the router is identified to the switch as
a unique device by the factory programmed World Wide Name (WWN).
Discovery Mode
This feature makes it easy to discover attached Fibre Channel and SCSI target
devices and automatically map them on the host side for the bus/port in question.
There are two discovery methods available:
■
Manual discovery
Auto discovery
■
Auto Discovery can be set to occur after reboot events (when the router reboots)
or link-up events (for instance, when cables are attached or a hub is rebooted).
Auto Discovery can be disabled by setting the router to Manual Discovery.
Host Device Configuration
A host system using a Fibre Channel Host Bus Adapter (HBA) will typically map
devices into the existing device-mapping scheme used by that operating system.
Refer to the HBA manual for the mapping table.
Mapping involves pairing FC_AL_PA to SCSI target address. The HBA will
claim enough SCSI bus entries to allow up to 125 Fibre Channel targets to be
mapped to SCSI Bus: Target entries. This is usually done by a fixed mapping of
AL_PA to Bus: Target. In such a configuration, the router corresponds to a
Bus: Target identifier, with the attached SCSI devices appearing as logical units
(LUNs). Operating systems can extend the available SCSI limit of 15 targets per
bus. Although this is not an issue for the operating system or most applications,
there are cases where older applications can have expectations about what
constitutes a valid SCSI ID, and thus may not correctly handle certain mappings.
In particular, some applications may exhibit difficulties addressing target IDs
greater than 15 (for example, 16 and up). This situation can be resolved by
configuring the router to use hard addressing and setting the AL_PA to a value
less then 16 that the HBA will be able to map.
For example, depending on the Fibre Channel HBA, if the hard AL_PA selection
Some Fibre Channel HBAs will map devices differently, so verify the AL_PA by
reviewing the documentation for the HBA.
Network Storage Router N1200 User Guide
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Overview
Logical Unit Management
Because SAN resources can be shared, it is possible for multiple hosts to have
access to the same devices on the SAN. To prevent conflicts, the router provides
LUN management as a means to restrict device access to certain hosts. LUN
management goes beyond simple LUN masking, to prevent gaps in the list of
LUNs presented to a host.
LUN management maps can be created for different views of the devices attached
to the router. Each Fibre Channel host is assigned a specific map configuration.
Not only can the administrator control which devices a host may access, but also
which LUNs are used to access these devices.
For a Fibre Channel host, a map is a table of LUNs, where each entry is either
empty or contains device address information needed for host/device
communication.
For a SCSI host, a map contains a list of target IDs, each of which has its own
table of LUNs with address information needed for host/device communication.
Note: The router can respond to multiple Target IDs on a SCSI bus.
Both Fibre Channel ports and SCSI buses have user-defined maps and predefined
maps.
There are three predefined maps:
■
■
■
Indexed Maps
Auto Assigned Maps
SCC Maps
When a host sends a command, the router will select which map to use, based on
the port receiving the command and the ID of the host sending the command. For
Fibre Channel ports, the host ID is the World Wide Name; for SCSI buses, the
host ID is the Initiator ID (0 - 15). When a host is unknown or is not assigned a
specific map, the router will use the default map.
Indexed Maps
An indexed map is initially empty and can be modified by the user.
34
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Overview
Auto Assigned Maps
An auto assigned map is built dynamically and contains all of the devices found
during discovery. This map will change automatically any time the discovery
process finds a change in the devices attached. This map cannot be modified by
the user.
SCC Maps
An SCC map is only available on Fibre Channel ports and contains only a single
entry for LUN 0. This LUN is a router controller LUN. Access to attached devices
is managed using SCC logical unit addressing.
Buffered Tape Writes
This option is designed to enhance system performance by returning status on
consecutive write commands prior to the tape device receiving data. If data does
not transfer correctly, the router returns a check condition on a subsequent
command.
Commands other than Writeare not issued until status is received for any
pending write, and status is not returned until the device completes the command.
This sequence is appropriate for tasks such as file backup or restore.
Some applications require confirmation of individual blocks being written to the
medium, such as for audit trail tapes or log tapes. In these instances, the Buffer
Tape Writes option must be disabled.
Network Storage Router N1200 User Guide
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Overview
36
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User
Interface
3
The HP StorageWorks Visual Manager user interface (UI) provides a graphical
format that is used to remotely view and change router configurations. Use the
Microsoft Internet Explorer or Netscape (version 6.2 or greater) web browsers to
access Visual Manager.
documents can be found at www.w3.org/TR/
.
This chapter describes the menus and tasks of the Visual Manager UI and is
■
■
■
■
Visual Manager Access, page 39
Visual Manager Best Practices, page 41
Main Menu, page 42
System Menu, page 45
— Serial Configuration
— Network Configuration
— SNMP Configuration (not supported)
— Active Fabric Configuration
— User Configuration
— Real-Time Clock Configuration
— Reset Menu
■
— Fibre Channel Port Configuration
— SCSI Bus Configuration
Discovery Menu, page 63
■
■
Mapping Menu, page 64
Network Storage Router N1200 User Guide
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
— Common Fibre Channel and SCSI Mapping Tasks
— SCSI Mapping Tasks
■
■
Statistics Menu, page 73
Utilities Menu, page 74
— FTP Utility Access
— Trace Settings Configuration
— Current, Previous, and Last Assert Trace Displays
— Event Log Configuration
— Event Log Display
— Clear Event Log
■
■
Report Menu, page 84
Reboot Option, page 85
38
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Visual Manager Access
Visual Manager (VM) can be accessed from any standard web browser:
1. Connect a 10/100BaseT Ethernet cable to the back of the router.
2. Apply power to the connected SCSI and/or Fibre Channel devices.
Wait for all of the devices to complete their power-up routines.
3. Apply power to the router.
4. Apply power to the host computer.
5. Enter the router IP address in the address field of the Web browser of the host
computer.
Note: To access VM, the router must be assigned a valid IP address. The factory default setting
for the IP address allows access on a local area network only. If the factory default for the IP
address is already used by another device on the local network, the IP address must be
changed.
The factory default for the IP address is http://1.1.1.1/
Note: If the IP address of the router is not known or needs to be changed, connect to the router
using a serial connection. The current router IP address is displayed and can be changed in the
serial Ethernet Configuration Menu.
The Visual Manager home page is displayed, showing router status
information. The home page is accessible to anyone who knows the router IP
address.
6. Select the desired menu option to access menus and screens.
The Password dialog box is displayed.
Network Storage Router N1200 User Guide
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
7. Enter the authorized user name and password (see Figure 8).
Figure 8: Password dialog box
The default user name is rootand the default password is password. This
information is required only once per session.
Note: HP recommends changing the user name and password from the defaults.
Note: Username and password are case-sensitive.
Full access is granted to the VM menus.
Note: To end the current session of VM, the browser window must be closed.
Navigating the browser to another URL does not end the current session.
40
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Visual Manager Best Practices
The following recommendations should be observed:
■
A standard keyboard and mouse must be used to navigate in the VM.
■
The router is shipped with a configuration of default settings that is acceptable
for most system environments. Few changes to the configuration should be
necessary.
■
After any configuration changes are made, depending on the menu option,
select Submit or Configure to send changes from the Web browser to the
router.
■
■
Changes will take effect during the next router reboot cycle.
If the configuration has been modified to meet company-specific needs, back
up the company-specific configuration to an external file. If necessary, these
settings can later be restored to the router.
■
Except for the user name, password, and override settings, fields are not
case sensitive.
■
■
HP recommends that you not bookmark VM pages with the Web browser.
Because configuration information is transmitted via URLs, it is possible that
the router could be configured with information present at the time a page was
bookmarked.
■
■
HP recommends navigating using only the Web page links contained in VM
itself.
Depending on the Web browser used, these links will often appear as
highlighted text. By selecting these links, VM can be safely navigated.
Network Storage Router N1200 User Guide
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Main Menu
The Main Menu home page is displayed whenever VM is accessed.
The home page contains status information, including a physical image of the
router (see Figure 9).
Figure 9: Visual Manager Home page
Home page information includes:
■
The HP logo is located in the upper left corner of the page. Figure 10 is an
example of this portion of the home page screen. If the Internet is accessible
to the host, click the HP logo to open the HP website.
Figure 10: HP logo
42
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
■
An illustration of the router is located near the top of the home page.
Figure 11 is an example of this portion of the home page screen.
Figure 11: VM router image
■
The router image is interactive, allowing quick access to configuration menus:
— To display current settings and status for a port, click the corresponding
port shown in the router image.
— To open a menu for making changes to the configuration for that
particular port or bus, click the desired Fibre Channel port or SCSI bus.
— To open the Network Configuration Menu, click the Ethernet port.
■
Router status information is located in the body of the home page and
includes:
— Platform information
— Temperature measurements
The home page monitors the temperature of the router, checking once
every 60 seconds. If the detected temperature is outside the operating
range, a pop-up notification message indicates that the unit is about to
shut down.
— Voltage measurements
Note: The temperature warning message appears only on the home page.
Network Storage Router N1200 User Guide
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
■
The Main Menu option bar is located at the left-side of the home page. Use
this option bar to access the configuration menus (see Figure 12).
Figure 12: Main Menu option Bar
■
Main Menu options:
— Home displays router status information.
— System configures standard system components.
— Ports configures the Fibre Channel port and SCSI buses.
— Discovery displays devices and discovers new devices.
— Mapping displays and configures maps.
— Statistics displays router statistics.
— Utilities configures utility settings.
— Report displays system information.
— Reboot restarts the router.
Each Main Menu option is discussed in the following sections of this chapter.
44
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
System Menu
The System Menu is accessed from the Main Menu and is used to view and
configure serial, network, Trap, Active Fabric, clock, and power supply
components (see Figure 13).
Figure 13: System page
System page tasks:
■
■
■
■
■
■
■
Serial configuration configures the baud rate.
Network configuration configures Ethernet settings.
Active Fabric configuration configures Active Fabric settings.
User configuration configures user security settings.
Real-Time Clock configuration configures system date and time.
Power Supply configuration configures the number of power supplies.
Reset menu restores factory default settings.
Each menu option is discussed in the following paragraphs.
Network Storage Router N1200 User Guide
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Serial Configuration
The Serial screen is used to change the baud rate for the serial port
(see Figure 14).
If the Autobaud feature is being used, it may not be necessary to set the baud rate.
Figure 14: Serial screen
The current baud-rate setting is displayed.
HP recommends setting the baud rate to 115200.
46
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Network Configuration
The Network screen is used to enter network settings, including Ethernet settings
(see Figure 15).
Figure 15: Network screen
Network Menu options:
■
Network Settings changes the hostname.
■
Port Configuration changes Ethernet configuration settings.
Each of these Network Menu options is discussed in the following sections.
Network Settings
To change the hostname, enter an alphanumeric entry of one word up to 8
characters in length. Then, select Submit.
Network Storage Router N1200 User Guide
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Port Configuration (Ethernet Settings) (Service Mode - Restricted Access)
To change the Ethernet configuration settings, select the Ethernet port icon.
The Ethernet Configuration dialog box is displayed (see Figure 16).
Figure 16: Ethernet Configuration dialog box
Ethernet configuration settings:
■
Ethernet Mode can be set to one of the following options:
— 10Mps Only
— 100Mps (half duplex) Only
— 100Mps (full duplex) Only
— 10/100Mps (Auto-Neg.)
■
MAC address is the Ethernet physical address of the router.
Caution: If this configuration setting is incorrectly set, processing difficulties may
occur. Before changing this setting, evaluate the need for the change and verify the
desired setting. HP recommends backing up the router configuration to an external file
before making changes to this setting.
The Ethernet physical address is always assigned by the manufacturer.
■
■
■
IP address (default: 1.1.1.1) is the IP address of the router.
Subnet Mask (default: 255.255.255.0) is the IP subnet mask for the router.
IP Gateway (default: 0.0.0.0) is the IP address of the gateway for the Ethernet
network connected to the router.
■
DHCP enables or disables support for Dynamic Host Configuration Protocol
(DHCP).
48
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
When DHCP is enabled, the router requests a dynamic IP address from a
DHCP server on the Ethernet network. The router must be rebooted before an
IP address will be requested from the DHCP server. After the router is
rebooted, the HTTP session must be restarted. The IP address will be different
from the former non-DHCP IP address.
Note: To use the DHCP feature, a DHCP server must be operational on the Ethernet
network. If the DHCP feature is used when there is not DHCP server, the standard for
DHCP requires the router wait thee minutes for a response from a DHCP server before
timing out.
Some DHCP servers allow a lease reservation to be set up for an IP address by
providing the server with the Ethernet MAC address. The DHCP server
always provides the same IP address to the router. This setup can be useful for
remote management of the router via Telnet or VM. Because the method of
setting up a lease reservation varies, depending on the DHCP server being
used contact the Network Administrator for assistance.
Network Storage Router N1200 User Guide
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Active Fabric Configuration
The Active Fabric screen allows setup of Active Fabric options (see Figure 17).
Figure 17: Active Fabric screen
Active Fabric settings:
■
Server-Free Backup Mode toggles between Enabled and Disabled.
When enabled, server-free backup capability is enabled to allow Extended
Copy commands.
■
Number of Controller LUNs (default: 1) sets the number of controller LUNs
reported by the router.
The number must be in the range of 0 through 4.
Note: For Server-Free Backup Mode functionality, if addressing a controller LUN is
desired, at least one controller LUN must be enabled and included in a relevant map.
enabled to allow router access to Fibre Channel targets.
50
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
For information on controller LUN and Extended Copy commands, see Appendix
B, “Controller LUN Commands.”
For general information about server-free backups, see Chapter 1, “Introduction.”
User Configuration
The User screen is used to set up router security (see Figure 18).
Figure 18: User screen
User settings:
■
User Name (default: root) is any alphanumeric combination.
Password (default: password) is any alphanumeric combination.
■
The user name and password should be unique and kept confidential. HP
recommends using a combination of letters and numbers when creating the user
name and password.
Note: These security settings affect all user interfaces of the router.
Network Storage Router N1200 User Guide
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Real-Time Clock Configuration
The Real Time Clock screen is used to set the system time and date
(see Figure 19).
Figure 19: Real-Time Clock screen
Real-Time Clock settings:
■
Date Settings sets the month, date, and year.
— Use a four-digit number to represent the year.
Day of Week sets the day of week.
■
■
Time Settings sets the hours, minutes, and seconds.
— The system clock is a 24-hour clock.
52
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Reset Menu
The Reset Menu is used to reset the router to factory default settings
(see Figure 20).
Figure 20: Reset to Factory Default screen
Current router activities are disrupted while the unit resets the configuration to the
factory defaults and saves those options to FLASH memory.
Caution: Resetting the router configuration to the factory defaults will delete
custom maps or map changes.
Note: Resetting to factory defaults through VM will not affect Ethernet connectivity.
User-configured values for the IP address and gateway will be retained.
Network Storage Router N1200 User Guide
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Ports Menu
Accessed from the Main Menu, the Ports Menu is used to view and modify
configuration settings of the Fibre Channel port and SCSI buses (see Figure 21).
Figure 21: Ports Menu
The initial screen display of the Ports Menu includes summary information about
each Fibre Channel port and SCSI bus in the router.
Note: To view or change configuration settings of a specific port or bus, select it from
the menu bar on the left side of the screen or select the port or bus from the router
image at the top of the screen.
To make changes, modify the setting and then click Submit.
54
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Ports Menu tasks:
■
Fibre Channel Port configuration changes Fibre Channel port settings.
SCSI Bus configuration changes SCSI bus settings.
■
Each Ports Menu option is discussed in the following subsections.
Fibre Channel Port Configuration
When the Fibre Channel port is selected in Ports Menu, the Fibre Channel
Configuration screen is displayed (see Figure 22).
Figure 22: Fibre Channel Configuration screen
Fibre Channel port settings:
■
Link Status indicates the port link status.
■
Port Name High sets a new value for the World Wide Port Name High.
Caution: If this configuration setting is incorrectly set, processing difficulties
may occur. Before changing this setting, evaluate the need for the change and
verify the desired setting. HP recommends backing up the router configuration
to an external file before making changes to this setting.
■
Port Name Low sets a new value for the World Wide Port Name High.
Network Storage Router N1200 User Guide
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Caution: If this configuration setting is incorrectly set, processing difficulties
may occur. Before changing this setting, evaluate the need for the change and
verify the desired setting. HP recommends backing up the router configuration
to an external file before making changes to this setting.
■
Port Mode (default: N_Port) sets the port mode.
Port Mode settings:
— Auto Sense: In this mode, the Fibre Channel port tries to negotiate as a
loop. If it is not successful, then the Fibre Channel port negotiates as a
fabric. If the port comes up as a loop, it then determines whether it is on a
private or public loop.
— N_Port: (default) This mode allows the router to bypass the loop
negotiation and come up as a fabric only. If the router is on a loop, and
N_Port mode is selected, an error in communication may occur.
■
■
Hard AL_PA Settings displays the AL_PA Lookup Table.
Use the table to find the node number. This unique one-byte valid value
(derived from an Arbitrated Loop Topology defined in ANSI specification
FC_AL version 4.5) is used for the Fibre Channel configuration
(see Figure 23).
Figure 23: AL_PA lookup table
56
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
■
Discovery Mode (default: manual discovery on reboot events) determines
how the router will discover new Fibre Channel devices.
Discovery mode settings:
— Auto Discovery on Reboot Events allows the router to automatically
discover all Fibre Channel devices when rebooted or when link-up events
occur, such as connecting cables or rebooting network hubs.
— Both the ports and the devices behind the ports are discovered on all
subsequent link-up events.
— Auto Discovery on Link Up Events allows the router to automatically
discover all Fibre Channel devices when rebooted or when link-up events
occur, such as connecting cables or rebooting network hubs.
— Both the ports and the devices behind the ports are discovered for the first
link-up event. Subsequent link-up events will only discover the ports and
not the devices behind the ports.
— Manual Discovery Only (default) sets discovery of new devices to occur
only after the user selects the Discovery option from the Main Menu or
when a Registered State Change Notification (RSCN) is received from a
fabric.
Note: SCSI devices attached to a Fibre Channel must be mapped as sequential Fibre
Channel LUNs starting at LUN number 00. Skipping LUN numbers is not recommended
when mapping Fibre Channel LUNs because Fibre Channel Discovery stops the
discovery process whenever an empty LUN position is found.
■
Buffered Tape Writes (default: enabled) enables or disables the Buffered
Tape Writes option.
Caution: If this configuration setting is incorrectly set, processing difficulties
may occur. Before changing this setting, evaluate the need for the change and
verify the desired setting. HP recommends backing up the router configuration
to an external file before making changes to this setting.
When enabled, to enhance performance, Buffered Tape Writes return status
on consecutive write commands prior to the tape device receiving data.
Network Storage Router N1200 User Guide
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
■
■
Buffered Tape Queue Depth sets the Buffered Tape Queue Depth.
Select a setting of 0 through 10 from the drop-down list.
Default Map (default: indexed) sets the current mapping mode for the
selected port.
The current map can be set to:
router.
— SCC
For more information about mapping modes, see Appendix C, “Addressing
Methods and Table Structures” on page 169.
For information on changing map settings, see “Mapping Menu” on page 64.
■
Performance Mode (default: 2 Gbps) toggles between 1 Gbps and 2 Gbps.
Note: If set incorrectly and the router is plugged into a Loop or Fabric, the unit may
receive Framing errors due to the incorrect Fibre Channel link speed.
■
Override Settings (service mode-restricted access) enhances interoperability
with some storage devices that require special consideration during setup of
the router configuration menus.
— Hi-Sup Bit toggles between Set and Clear.
— Force FCP Response Code toggles between Off and On for support of
HP-specific HBA #223180-B21 and #120186-001.
— Initiator Bit toggles between Set and Clear.
— When using the router in a router-to-router configuration, this option
should be configured to Set. A router-to-router configuration is a type of
configuration where one router appears as a target to another initiator
router.
— Link Garbage Deletion toggles between Enabled and Disabled.
58
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
SCSI Bus Configuration
When a SCSI bus is selected in the Ports Menu, the SCSI Bus Configuration
screen is displayed (see Figure 24).
Figure 24: SCSI Bus Configuration screen
SCSI bus configuration settings:
■
Primary Initiator ID (default: 7) must be a unique ID.
■
Alternate Initiator ID (service mode-restricted access) (default: none) will
be used if the primary ID is taken. Must be a unique ID.
■
Target ID(s) adds or removes Target IDs.
Caution: If this configuration setting is incorrectly set, processing difficulties
may occur. Before changing this setting, evaluate the need for the change and
verify the desired setting. HP recommends backing up the router configuration
to an external file before making changes to this setting.
Note: Target IDs must be setup prior to mapping devices on the SCSI bus.
Network Storage Router N1200 User Guide
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Note: Do not enable Target IDs unless there is a SCSI initiator on the bus that wants to
use Fibre Channel devices. This type of configuration is known as a Target Mode
configuration.
■
■
Discovery toggles between Enabled and Disabled.
Discovery Delay is the wait time after a power-up or reboot before
discovering SCSI devices.
Note: HP recommends setting the value to at least 2 seconds to ensure all SCSI devices
complete their individual power-ups.
■
Bus Reset on Boot toggles between Enabled and Disabled.
When enabled, the router will automatically reset SCSI buses during a power
up or reboot of the router.
Internal Termination toggles between Enabled and Disabled.
Caution: If this configuration setting is incorrectly set, processing difficulties
may occur. Before changing this setting, evaluate the need for the change and
verify the desired setting. HP recommends backing up the router configuration
to an external file before making changes to this setting.
When enabled, internal termination of the selected SCSI bus is allowed. When
disabled, the SCSI Bus, not the router handles SCSI termination.
■
Buffered Tape Writes (default: Enabled) toggles between Enabled and
Disabled.
When enabled, Buffered Tape Writes enhance system performance. Buffered
Tape Writes return status on consecutive write commands prior to the tape
device receiving data.
■
Default Map (default: auto-assigned) sets the current mapping mode for the
selected bus.
60
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Caution: If this configuration setting is incorrectly set, processing difficulties
may occur. Before changing this setting, evaluate the need for the change and
verify the desired setting. HP recommends backing up the router configuration
to an external file before making changes to this setting.
The current map can be set to:
— Indexed
— Auto-assigned (default) contains all the devices attached to the router.
— SCC
For more information about mapping modes, see Appendix C, “Addressing
Methods and Table Structures” on page 169.
For information on changing map entries, see “Mapping Menu” on page 64.
■
Override Settings (service mode-restricted access) To override the settings of
a SCSI target, select a Target ID icon with the appropriate Target ID number.
After a specific Target is selected, the SCSI Override sub-screen is displayed
and is used to enter the Override settings (see Figure 25).
Figure 25: SCSI Device Override screen
SCSI bus override settings:
— CDB Length Override enables or disables the override of default CDB
lengths.
— CDB Group 6 Length Default (default: 0) can be set to 0, 6, 10, or 12.
— Wide Negotiation enables or disables negotiation on a wide SCSI bus.
Network Storage Router N1200 User Guide
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
— Synchronous Negotiation enables or disables synchronous negotiation
on the SCSI bus.
— Synchronous Parameter Override enables or disables parameters for
synchronous negotiation.
— Synchronous Period (default: 40) sets the maximum number of seconds
allowed for negotiation.
— Synchronous Offset (default: 16) sets the maximum variation in transfer
rate that can be negotiated in megabytes per seconds (MB/s).
— Ultra SCSI-3 Negotiation enables or disables Ultra SCSI-3 support for
the selected Target ID.
— When enabled, Ultra SCSI-3 Negotiation helps solve certain
compatibility issues in mixed vendor environments where there may be a
device that cannot handle automatic negotiation of the bus speed or where
there is a device that negotiates to use Ultra SCSI-3 but cannot handle the
speed.
62
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Discovery Menu
Accessed from the Main Menu, the Discovery Menu is used to view Target
devices and discover new Target devices (see Figure 26).
Figure 26: Discovery page
To perform a manual discovery:
1. Select the Fibre Channel port or SCSI bus from the menu bar or the router
image.
2. Then, select Go.
Network Storage Router N1200 User Guide
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Mapping Menu
Each physical port/bus on the router can have the following maps:
Table 5: Device Map Types
Map Type
Auto Assigned
Indexed (default)
SCC
System/User Generated
Fibre Channel or SCSI
Fibre Channel and SCSI
Fibre Channel and SCSI
SCSI
System
System
System
User
Custom
Fibre Channel and SCSI
Each map has a unique name and map ID; one of the maps must be identified as
the “current” map for the router to use.
Accessed from the Main Menu, the Mapping Menu is used to view and modify
host and map information for a Fibre Channel port or SCSI bus. Maps and hosts
can be added, edited, or deleted.
To view or change map settings of a specific port or bus:
1. Select the port or bus from the menu bar on the left side of the screen or from
the router image at the top of the screen.
2. Specific mapping information is displayed, including the name of the port, the
selected host, and the assigned map.
Submit.
Because some mapping configuration settings are the same for Fibre Channel and
SCSI maps and some settings are unique, this mapping section is subdivided as
follows:
■
■
■
Common Fibre Channel and SCSI Mapping Tasks, page 65
Fibre Channel Mapping Tasks, page 66
SCSI Mapping Tasks, page 70
64
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Common Fibre Channel and SCSI Mapping Tasks
Although the initial screen display for Fibre Channel and SCSI maps differs
slightly, the available actions are the same (see Figure 27).
Figure 27: Initial Mapping screen
Mapping screen options:
■
■
■
■
Add Host adds a new host.
To add an undefined host, type the hostname in the Add Host field and then
click Add.
Select Host adds a known host.
To select a previously set up host, expand the Select Host drop-down box and
select the host from the list.
Edit/View Host displays or changes host information.
Viewing and changing Host information is discussed in the following
paragraphs.
Delete Host deletes the current host.
■
Add Map adds a new map.
Network Storage Router N1200 User Guide
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
To add an undefined map, type the name of the map in the Add Map field and
then click Add.
■
■
■
Select Map adds a known map.
To select a previously set up map, expand the Select Map drop-down box and
select the map from this list.
Edit/View Map displays or changes map information.
Viewing and changing Map information is discussed in the following
paragraphs.
Delete Map deletes the current map.
Note: ”Indexed,” “Auto Assigned,” and “SCC” maps cannot be deleted or renamed.
■
Clone Map makes a copy of the current map.
Cloning makes it easier to setup new maps with similar information to
previously created maps. The new map must have a unique map ID and name.
Note: SCC and Auto-Assigned maps cannot be cloned.
Fibre Channel Mapping Tasks
Configuration tasks for Fibre Channel mapping includes:
■
Viewing and changing Fibre Channel host information
Viewing and changing Fibre Channel map information
■
Each task is discussed in the following paragraphs.
Viewing and Changing Fibre Channel Host Information
To view or change current host information:
1. In the Mapping Menu screen, select the desired Fibre Channel port.
2. Click Edit/View in the Host section of the screen.
The Fibre Channel Host Name dialog box is displayed. Current host
information is shown at the top of the dialog box.
66
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
3. Enter the new settings and then select Modify (see Figure 28).
Figure 28: Fibre Channel Host Name dialog box
Fibre Channel Host Name settings:
■
■
■
■
■
■
■
Host Name
Host ID (hexadecimal)
Port WWN Hi (hexadecimal) (service mode-restricted access)
Port WWN Lo (hexadecimal) (service mode-restricted access)
Node WWN Hi (hexadecimal) (service mode-restricted access)
Node WWN Lo (hexadecimal) (service mode-restricted access)
Map Name
Network Storage Router N1200 User Guide
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Viewing and Changing Fibre Channel Map Information
To view or change current Fibre Channel map host information:
2. Select Edit/View in the Map section of the screen.
The Fibre Channel Map dialog box is displayed. Current map information is
shown at the top of the dialog box.
3. Enter the new settings and then select the appropriate action button
(see Figure 29).
Figure 29: Fibre Channel Map dialog box
Note: Auto-Assigned and SCC maps cannot be modified, cleared, filled, or have
entries removed.
Note: Map settings are saved to memory when any button within the page is selected.
68
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Fibre Channel map settings:
■
Clear Map clears all entries from the current map.
■
Remove Gaps removes any incremental gaps in the sequence of LUN listed
in the table.
When the system removes gaps from the table, the LUN are renumbered in
sequential order, starting with LUN 0.
Note: Some operating systems require gaps be removed in the mapping table in order
to detect all devices.
■
Fill Map fills in the current map.
To use the Fill Map option, expand the Fill Map Priority drop-down box,
select the fill option, and then click Fill Map.
When the map is filled, the display shows the current devices.
■
Delete deletes map entries.
To delete map entries, expand the Delete Map Item LUN drop-down box,
select the LUN, and then click Delete.
To delete a range of LUNs, select the beginning LUN to delete from the
“from” drop-down box and select the last LUN to delete from the “to”
drop-down box.
■
■
Discovered Device Entry adds a discovered device to the map.
To add a discovered device to the map, use the drop-down boxes to enter the
settings, and then click Create Entry in the Discovered Device Entry section
of the screen.
Manual Device Entry creates a map entry for a device that is not yet
discovered or installed.
To add a new device to the map, use the drop-down boxes to enter the settings,
and then click Create Entry in the Manual Device Entry section of the
screen.
Network Storage Router N1200 User Guide
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
SCSI Mapping Tasks
Configuration tasks for SCSI mapping include:
■
Viewing and Changing SCSI Host Information
Viewing and Changing SCSI Map Information
■
Each task is discussed in the following paragraphs.
Viewing and Changing SCSI Host Information
To view or change current SCSI host information:
1. In the Mapping Menu screen, select the desired SCSI bus.
2. Click Edit/View in the Host section of the screen.
The SCSI Host Name dialog box is displayed. Current host information is
shown at the top of the dialog box.
3. Enter the new settings and then click Modify (see Figure 30).
Figure 30: SCSI Host Name dialog box
SCSI Host Name settings:
■
■
■
Host Name
Initiator ID
Map Name
70
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Viewing and Changing SCSI Map Information
To view or change current SCSI map host information:
2. Select Edit/View in the Map section of the screen.
The SCSI Map dialog box is displayed. Current map information is shown at
the top of the dialog box.
3. Enter the new settings and then click the appropriate action button
(see Figure 31).
Figure 31: SCSI Map dialog box
Note: To map Fibre Channel devices to any SCSI initiator on the selected bus, a Target
ID must be enabled from the SCSI Bus Configuration Menu. A Target ID should only be
added if there is a SCSI initiator that needs to address Fibre Channel devices. Each
Target ID can be used to store up to 32 Fibre Channel devices.
Note: Auto-Assigned and SCC maps cannot be modified, cleared, filled, or have
entries deleted.
Note: Map settings are saved to memory when any button within the page is selected.
Network Storage Router N1200 User Guide
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Note: SCSI maps can be filled or devices can be added to them only when at least one
SCSI Target ID has been enabled in the SCSI Bus Configuration Menu.
SCSI Map settings:
■
Clear Map clears all entries from the current map.
Fill Map fills in the current map.
■
When the map is filled, the display shows the current devices.
■
Remove Gaps removes any incremental gaps in the sequence of LUN listed
in the table.
When the system removes gaps from the table, the LUN are renumbered in
sequential order, starting with LUN 0.
Note: Some operating systems require gaps be removed in the mapping table to detect
all devices.
■
■
■
Delete deletes map entries.
To delete a range of LUNs, select the beginning LUN to delete from the
“from” drop-down box and select the last LUN to delete from the “to”
drop-down box.
Discovered Device Entry adds a discovered device to the map.
To add a discovered device to the map, use the drop-down boxes to enter the
settings, and then click Create Entry in the Discovered Device Entry section
of the screen.
Manual Device Entry creates a map entry for a device that is not yet
discovered or installed.
To add a new device to the map, use the drop-down boxes to enter the settings,
and then click Create Entry in the Manual Device Entry section of the
screen.
72
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Statistics Menu
Accessed from the Main Menu, the Statistics Menu is used to display Fibre
Channel port and SCSI bus information (see Figure 32).
Figure 32: Statistics Menu
To view information for a specific port or bus, click the component on the menu
bar or the router image. To refresh the display, select Reset SCSI system
statistics.
Network Storage Router N1200 User Guide
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Utilities Menu
Accessed from the Main Menu, the Utilities Menu is used to view and configure
utility options (see Figure 33).
Figure 33: Utilities Menu
Utility Menu tasks:
■
■
■
■
■
■
■
■
■
■
FTP Utility access opens an FTP session.
Trace Settings configuration configures trace settings.
Current Traces display displays current trace information.
Previous Traces display displays previous trace information.
Last Assert Traces display displays last assert trace information.
Clear Current Traces clears current trace information.
Clear Assert Traces clear current trace information.
Event Log Settings configures Event Log settings.
Event Log display displays the Event Log.
Clear Event Log clears the Event Log.
Each Utility Menu option is discussed in the following sections.
74
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
FTP Utility Access
The FTP utility screen is used to open an FTP session (see Figure 34).
Figure 34: FTP Utility screen
The FTP utility requires the use of a JAVA applet and prompts for permission to
install the applet, if needed. If the prompt is displayed, follow the onscreen
instructions to complete the installation. The FTP utility then prompts for
permission to run the applet.
Note: Internet access is required to verify the signature for the HP FTP applet and to
download the JAVA applet plug-in for your browser.
To open an FTP session:
1. Enter the User Name, Password, and the IP address of the router.
2. Click Connect.
3. Select the local file to upload or download. If necessary, click Browse to
scroll through a file list.
The following file types can be uploaded to the router:
— Configuration (.cfg)
— Firmware (.dlx)
Network Storage Router N1200 User Guide
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
The following file types can be downloaded from the router:
— Configuration (.cfg)
— Traces for the current boot cycle (curtrace.txt)
— Traces from the previous boot cycle (prvtrace.txt)
4. Click Binary Transfer mode.
5. Choose the desired task:
— To download a file, click Get.
— To upload a file, click Put.
Note: If a valid firmware or configuration file is uploaded to the router, an automatic
reboot will occur once the file has been received. The router cannot be accessed from
the Visual Manager UI during the time that the reboot is in process, which is
approximately 30 seconds.
76
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Trace Settings Configuration
The Trace Settings screen is used to configure the trace settings (see Figure 35).
Figure 35: Trace Settings screen
Current Trace settings are displayed.
To change the settings, use the drop-down boxes and choose the desired setting.
After all changes are completed, select Submit.
Table 6 is a brief description list of the trace settings.
Table 6: Trace Settings
Setting
General Errors
FCP Transport
Description
Displays the most serious errors and exception conditions.
Fibre Channel Protocol transport functionality will be
monitored and recorded.
PS Transport
PS Driver
Parallel SCSI transport functionality will be monitored and
recorded.
Parallel SCSI driver functionality will be monitored and
recorded.
Timing
AF
Timer functions will be monitored and recorded.
Active Fabric firmware will be monitored and recorded.
Network Storage Router N1200 User Guide
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Table 6: Trace Settings
Setting
Description
FCP Driver
Fibre Channel Protocol driver functionality will be monitored
and recorded.
FCP Management
Fibre Channel Protocol management functionality will be
monitored and recorded.
PS Management
SG List
Parallel SCSI functionality will be monitored and recorded.
Scatter/gather list will be monitored and recorded
FCP/RMI
Fibre Channel Protocol routing layer will be monitored and
recorded.
INBAND
Controller management functionality will be monitored and
recorded.
78
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Current, Previous, and Last Assert Trace Displays
These three Utilities Menu screens show trace information. The Current Traces
screen shows data since the router was last booted. The Previous Traces screen
shows data from the last boot cycle. The Last Assert Traces screen shows data
since the last assertion (see Figure 36).
Figure 36: Current Traces screen
Network Storage Router N1200 User Guide
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Clear Current Traces and Clear Assert Traces
These Utilities Menu screens are used to clear the current trace buffer or the assert
trace buffer.
Current router activities will not be disrupted while the buffer is cleared
(see Figure 37).
Figure 37: Clear Current Trace Buffer screen
80
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Event Log Configuration
The Event Log Setting screen is used to configure Event Log filters
(see Figure 38).
Figure 38: Event Log settings screen
Event Log settings:
■
■
■
■
Log All Events
Disable/Enable Event Logging
Log Error Events
Log Notify Events
Event logging captures the last 215 events and then starts overwriting the log.
Note: To ensure accurate event logging, be sure to correctly set the clock and date in
the Real Time Clock Configuration Menu.
Network Storage Router N1200 User Guide
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Clear Event Log
The Clear Event Log screen is used to clear the Event Log (see Figure 40).
Current router activities will not be disrupted.
Figure 40: Clear Event Log screen
Network Storage Router N1200 User Guide
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Report Menu
Accessed from the Main Menu, the Report screen displays a consolidated view of
all system information, including environmental conditions (see Figure 41).
Figure 41: Report screen
84
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
Reboot Option
Router reboots are executed using this router Main Menu option (see Figure 42).
When the router is rebooted, current router activities will be disrupted. All
submitted configuration changes will be activated during the boot-up process.
Figure 42: Reboot screen
Network Storage Router N1200 User Guide
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager User Interface
86
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
4
The Serial/Telnet User Interface (UI) is used to configure and manage the HP
StorageWorks Network Storage Router. This chapter describes the configuration
menus and option tasks available in the Serial/Telnet UI.
Note: Unless otherwise indicated, configuration changes take effect when the router
reboots.
During the start up process of the router, the Serial/Telnet UI displays initial
power-up messages. After the power-up process is completed, the Main Menu of
and tasks are listed. All configuration and management tasks are performed from
these menus.
This chapter is organized using the same structure as the router Main Menu and its
associated submenus. The sections are:
■
■
■
■
■
■
■
■
■
Ethernet Configuration, page 96
Fibre Channel Configuration, page 99
Device Mapping, page 106
— Selecting the current map
Network Storage Router N1200 User Guide
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
— Displaying the current map
— Creating a new map
— Removing the current map
— Cloning the current map
— Editing the host list for the current map
■
■
■
■
■
■
■
Save Configuration, page 129
Restore Last Saved Configuration, page 129
Reset and Save Configuration to Factory Defaults, page 129
— System statistics
— Event log
— Special Fibre Channel link states
Reboot Option, page 141
■
■
— Saving copies of the trace buffers using FTP
Download New Firmware Option, page 142
88
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Telnet UI Access
To open a Telnet session, the IP address of the router and a Telnet client utility are
required.
Note: After each reboot, a new Telnet session must be started. If router is reset to
factory settings, the Ethernet port will have to be re-configured using the serial interface.
From most Windows 9x, Windows NT, and Windows 2000 systems, a Telnet
session can be started from the Command (DOS) shell using the following steps:
1. From the Windows Start Menu, open the Command Prompt (DOS) window.
2. At the ‘>’ prompt, enter:
> TELNET <IP ADDRESS>
where <IP ADDRESS>is the IP address of the router
3. Enter the user name and password.
The default user name is rootand the default password is password.
HP recommends that the user name and password be changed from the default
values. The Configuration Menu is displayed.
Network Storage Router N1200 User Guide
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Serial UI Access
To open a serial session, a terminal emulator utility is required.
From most Windows 9x, Windows NT, and Windows 2000 systems, a
HyperTerminal session can be started using the following steps:
1. From the Windows Start Menu, open HyperTerminal.
2. Name the new terminal session.
3. Indicate the appropriate COM port.
4. Configure the serial port settings, as listed in Table 7.
Table 7: Serial Port Configuration
BAUD Rate
Autobaud, 9600, 19200, 38400, 57600, 115200
Data Bits
8
Stop Bit
1
Parity
None
Flow Control
XON/XOFF
Note: HP recommends setting the baud rate to 115200.
5. After completing the serial port configuration, select OK to start a serial
session.
6. After the serial session has started, press Enter several times to initiate router
communication and display the Configuration Menu.
90
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Power up Messages
When power is applied to the router, a series of messages is displayed on the serial
terminal or terminal emulation program (see Figure 43).
Figure 43: Power up messages
Note: Throughout this chapter, XX represents value fields.
Network Storage Router N1200 User Guide
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Serial/Telnet UI Main Menu
The Main Menu is the starting point for all configuration sub-menus and tasks
(see Figure 44).
Note: If the power up messages and the Main Menu are not displayed, check the serial
port settings.
Figure 44: Serial/Telnet Main Menu
Main Menu options:
■
■
■
1) Perform Configuration enters router configuration settings.
2) System Utilities displays system statistics and perform diagnostic tests.
3) Display Trace and Assertion History displays trace information and clear
the trace buffer.
■
■
4) Reboot reboots the router.
5) Download a New Revision of the Firmware replaces the current revision
of the router firmware with a different copy of firmware.
Each Main Menu option is discussed in a separate section of this chapter.
Note: Except for the login process, uppercase and lowercase characters can be used
interchangeably in all of the menus.
92
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Configuration Menu
The Configuration Menu is used to configure the router (see Figure 45).
Figure 45: Configuration Menu
Note: The router is shipped with a configuration of default settings that is acceptable
for most system environments. Few changes to the configuration should be necessary.
After any configuration changes are made, select A) Save Configuration to record the
changes.
If the configuration has been modified to meet company-specific needs, back up the
company-specific configuration to an external file. If necessary, these settings can later
be restored to the router.
Configuration Menu options:
■
■
■
1) Baud Rate Configuration changes the baud rate on the serial port.
2) Ethernet Configuration enters Ethernet network settings.
3) Fibre Channel Configuration configures the settings for the Fibre
Channel port.
■
■
4) Parallel SCSI Configuration configures the settings for the SCSI buses.
6) Trace and Event Settings Configuration modifies trace and event filter
settings.
Network Storage Router N1200 User Guide
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
■
■
7) Real-Time Clock Configuration sets the system clock.
8) Active Fabric Configuration enables and disables server-free backup and
change the number of controller LUNs.
■
■
■
A) Save Configuration saves changes to memory.
B) Restore Last Saved Configuration reverts to the previous configuration.
C) Reset and Save Configuration to Factory Defaults resets all
configuration options to the factory defaults.
■
X) Return to Main Menu goes back to the previous screen.
Because the Configuration Menu is the primary menu in the UI, each
Configuration Menu option is discussed in a separate section.
94
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Baud Rate Configuration
In the Configuration Menu, choose 1) Baud Rate configuration to change the
baud rate used on the serial port (see Figure 46).
Figure 46: Baud Rate Configuration Menu
Options include:
■
■
■
■
■
9600
19200
38400
57600
115200
Note: The asterisk (*) symbol indicates the current setting for the baud rate.
Note: If the Autobaud feature is being used, it is not necessary to set a baud rate.
Network Storage Router N1200 User Guide
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Ethernet Configuration
In the Configuration Menu, choose 2) Ethernet Configuration to set up the
Ethernet network. When this option is selected, the Ethernet Configuration Menu
is displayed.
Current Ethernet settings are displayed with available Ethernet configuration
options (see Figure 47).
Figure 47: Ethernet Configuration Menu
Note: To view or change configuration settings, select the desired menu option. After
completing configuration changes, select X) Return to previous menu and then select
A) Save Configuration to record the changes.
Ethernet Configuration Menu options:
■
■
2) Change IP Subnet Mask (default: 255.255.255.0) changes the router
Subnet mask.
96
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
■
■
3) Change IP Gateway (default: 0.0.0.0) changes the IP gateway for the
Ethernet network.
4) Change Ethernet Physical Address changes the Ethernet physical
address (MAC address).
Caution: If this configuration setting is incorrectly set, processing difficulties
may occur. Before changing this setting, evaluate the need for the change
and verify the desired setting. HP recommends backing up the router
configuration to an external file before making changes to this setting.
The manufacturer always assigns Ethernet physical addresses to the Ethernet
adapters.
■
5) Toggle Ethernet Mode changes the Ethernet mode.
Options include:
■
— 10 Mb/s only
— 100 Mb/s (half duplex) only
— 100 Mb/s (full duplex) only
— 10/100 MPS (Auto-Neg.)
■
■
6) Change Hostname changes the name of the host server.
The name can be any combination of alphanumeric characters, up to eight
characters.
■
7) Toggle DHCP Configuration enables or disables support for Dynamic
Configuration Protocol.
When DHCP is enabled, the router will request a dynamic IP address from the
DHCP server on the Ethernet network.
Some DHCP servers allow a lease reservation to be set up for an IP address by
providing the server with the Ethernet MAC address. The DHCP server will
then always provide the same IP address to the router. This setup can be
useful for remote management of the router such as Telnet or Visual Manager
Because the method of setting up a lease reservation varies depending on the
DHCP server being used, contact your Network Administrator for assistance.
Network Storage Router N1200 User Guide
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Note: To use the DHCP feature, a DHCP server must be operational on the Ethernet
network. If the DHCP feature is used when there is no DHCP server, DHCP standards
require the router wait three minutes for a response from a DHCP server before timing
out.
Note: Be sure to correctly set the clock and date in the Real Time Clock Configuration
Menu so that event logging is accurate.
■
■
8) Change SNMP Settings (SNMP is not supported)
9) Change Security Settings changes security settings, including the user
name and password.
The default user name is rootand the default password is password.
Caution: To ensure security, change the user name and password from the
default settings.
Note: The security settings entered here affect all user interfaces.
User names and passwords should be unique and kept confidential. HP
recommends using a combination of letters and numbers when creating user
names and passwords.
98
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Fibre Channel Configuration
In the Configuration Menu, choose Fibre Channel Configuration (3) to
configure the Fibre Channel port. The Fibre Channel Configuration Menu allows
the configuration of ALPA settings, discovery mode, tape backup settings, port
mode, default map, and override settings (see Figure 48).
Figure 48: Fibre Channel Configuration Menu
Fibre Channel Configuration Menu options:
■
1) Change World Wide Name High (service mode-restricted access)
changes the World Wide Port Name High.
Caution: If this configuration setting is incorrectly set, processing difficulties
may occur. Before changing this setting, evaluate the need for the change and
verify the desired setting. HP recommends backing up the router configuration
to an external file before making changes to this setting.
■
2) Change World Wide Name Low (service mode-restricted access) changes
the World Wide Port Name Low.
Network Storage Router N1200 User Guide
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Caution: If this configuration setting is incorrectly set, processing difficulties
may occur. Before changing this setting, evaluate the need for the change and
verify the desired setting. HP recommends backing up the router configuration
to an external file before making changes to this setting.
■
3) Toggle Hard AL_PA Usage changes the Hard AL_PA usage to either Yes
or No.
— If set to Yes, a unique one-byte valid value (derived from an Arbitrated
Loop Topology as defined in ANSI specification FC_AL version 4.5) is
used for the Fibre Channel configuration.
— When configuring the Fibre Channel AL_PA, the router presents a list of
loop addresses along with the corresponding AL_PA. The user can select
a loop address.
■
■
4) Change AL_PA Value changes the AL_PA value.
— The AL_PA lookup table is displayed. Enter a node number from the
table.
5) Toggle Discovery Mode (default: manual discovery on reboot events)
determines how the router will discover new Fibre Channel devices.
Options include:
— Auto Discovery on Reboot Events allows the router to automatically
discover all Fibre Channel devices during reboots, including both the
ports and the devices.
— Auto Discovery on Link-up Events allows the router to automatically
discover all Fibre Channel devices during reboots, including both the
ports and the devices for the first link-up event. Subsequent link-up events
will only discover the ports and not attached devices.
Note: SCSI devices attached to a Fibre Channel port must be mapped as sequential
Fibre Channel LUNs starting at LUN number 00. Skipping LUN numbers is not
recommended when mapping Fibre Channel LUNs because Fibre Channel Discovery
stops the discovery process whenever an empty LUN position is found.
100
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
— Manual Discovery Only (default) sets discovery of new devices to only
occur after the user selects the Refresh Device Display option. The
Refresh Device Display option is accessed from the System Utilities
Menu.
■
6) Toggle Buffered Tape Writes (default: Enabled) changes the tape backup
mode to either Enabled or Disabled.
Caution: If this configuration setting is incorrectly set, processing difficulties
may occur. Before changing this setting, evaluate the need for the change and
verify the desired setting. HP recommends backing up the router configuration
to an external file before making changes to this setting.
■
■
7) Change Buffered Tape Queue Depth changes the tape backup queue
depth. Select a value from 0 through 10.
8) Toggle Port Mode (default: N_Port) changes the port mode to either Auto
Sense or N_Port:
— Auto Sense: In this mode, the Fibre Channel port tries to negotiate as a
loop. If it is not successful, then the Fibre Channel port negotiates as a
fabric. If the port comes up as a loop, it then determines whether it is on a
private or public loop.
— N_Port (default): This mode allows the router to bypass the loop
negotiation and come up as a fabric only. Use this setting if a HP switch is
being used. If the router is on a loop and N_Port mode is selected, an error
■
9) Change Default Map Value (default: Indexed) changes and displays the
default current map for the port.
Mapping modes can be Auto-Assigned, Indexed (default), or SCC.
For more information about addressing methods, see Appendix C,
“Addressing Methods and Table Structures” on page 169.
Network Storage Router N1200 User Guide
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
■
A) Edit FC Override Settings (service mode-restricted access) enters Fibre
Channel override settings.
Caution: If this configuration setting is incorrectly set, processing difficulties
may occur. Before changing this setting, evaluate the need for the change and
verify the desired setting. HP recommends backing up the router configuration
to an external file before making changes to this setting.
A sub-screen is displayed, listing the following options:
— 1) Toggle Hi-Sup Bit Settings changes the Hi-Sup Bit settings.
Options include Set and Clear.
— 2) Toggle Forcing FCP Response Code for HP HBA #223180-B21 and
#120186-001, changes the forcing of the FCP response code.
Options include Off and On.
— 3) Toggle Initiator Bit Setting in PRLI_ACC changes the Initiator bit
setting. Options include Set and Clear.
If the router is deployed in a router-to-router configuration where at least
one router appears as target and another as initiator, set this option to Set.
— 4) Toggle Fibre Channel Link Garbage Deletion changes the Fibre
Channel Link garbage deletion.
Options include Enabled and Disabled.
102
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Parallel SCSI Configuration
In the Configuration Menu, choose 4) Parallel SCSI Configuration to configure
the SCSI buses. The Parallel SCSI Configuration Menu allows the configuration
of the SCSI discovery mode, SCSI bus reset, termination mode, tape backup
settings, and default current map (see Figure 49).
Figure 49: Parallel SCSI Configuration Menu
Current settings for the selected SCSI bus are displayed.
Network Storage Router N1200 User Guide
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
SCSI Configuration Menu options:
Caution: If these configuration settings are incorrectly set, processing
difficulties may occur. Before changing these settings, evaluate the need for the
change and verify the desired setting. HP recommends backing up the router
configuration to an external file before making changes to these settings.
■
1) Edit Initiator and Target Settings changes the SCSI Initiator and Target
settings.
The SCSI Initiator and Target Menu sub-screen is displayed, listing the
following options:
— 1) Enable/Disable SCSI Initiator enables or disables the SCSI Initiator.
Options are Enabled and Disabled.
— 2) Select primary and select/enable alternate SCSI ID sets the primary
and alternate initiator SCSI IDs (defaults: primary = 7; alternate = none).
These should be unique IDs on the bus.
— 3) Add Target ID or 4) Remove Target ID adds or removes a Target ID.
This adds an ID for a Fibre Channel device that responds to operation
requests from the SCSI initiator.
Note: Target IDs must be setup prior to mapping devices on the SCSI bus.
Note: Do not enable Target IDs unless a SCSI initiator on the bus wants to use Fibre
Channel devices. This type of configuration is known as a Target Mode configuration.
■
■
2) Enable/Disable SCSI Discovery enables or disables the Discovery Mode.
3) Enable/Disable SCSI Reset on Boot enables or disables automatic bus
resets after a reboot.
When enabled, the router will automatically reset SCSI buses during initial
power ups and reboots.
■
4) Set Discovery Delay Time sets the length of time the router waits after a
power-up or reboot before discovering SCSI devices.
104
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Note: This value should be set to no less than 250ms, according to the SCSI standard
for Reset-to-Selection Time. HP recommends setting the value to at least 2 seconds to
ensure all SCSI devices complete their individual power on self tests (POST.)
■
■
5) Set SCSI Termination Mode enables or disables the SCSI termination
mode.
6) Edit SCSI Target Override Settings changes the SCSI Target overrides.
SCSI Parameter Override Configuration Menu options:
— 1) Toggle CDB Length Override: enabled or disabled.
If enabled, the following configuration options are displayed:
CDB Group 6 Length Default (default = 0) can be set to 0, 6, 10, or 12.
CDB Group 7 Length Default (default = 0) can be set to 0, 6, 10, or 12.
— 2) Toggle Wide Negotiation: enabled or disabled.
— 3) Toggle Synchronous Negotiation: enabled or disabled.
If enabled, the following configuration options are displayed:
Synchronous Period (default = 40) is the maximum number of seconds
allowed for negotiation.
Synchronous Offset (default =16) is the maximum variation in transfer
rate that can be negotiated in MB/s.
— 4) Toggle Synchronous Parameter Override: enabled or disabled.
■
■
7) Enable/Disable Buffered Tape Writes (default: Enabled) enables or
disables Buffered Tape Writes.
tape device receives data, to enhance performance.
8) Change Default Map Value sets the default map to use for the bus.
Mapping modes can be Auto-Assigned (default), Indexed, or SCC.
For more information about addressing methods, see Appendix C,
“Addressing Methods and Table Structures” on page 169.
■ <Enter>scrolls to the next SCSI bus.
Network Storage Router N1200 User Guide
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Device Mapping
Each physical port/bus on the router can have the following maps:
Table 8: Device Map Types
System/User
Generated
Map Type
Auto Assigned
Indexed
Fibre Channel or SCSI
Fibre Channel and SCSI
Fibre Channel and SCSI
SCSI
System
System
System
User
SCC
Custom
Fibre Channel and SCSI
Each map has a unique name and map ID; one of the maps must be identified as
the “current” map for the router to use.
In the Configuration Menu, choose 5) Device Mapping to manipulate maps and
associate the selected hosts with a particular map. Maps are viewed, edited,
deleted, and cloned in the Device Mapping Menu (see Figure 50).
Figure 50: Device Mapping Main Menu
Device Mapping Configuration Menu options:
■
■
■
■
1) Select Current Map indicates which map is to be the Current map.
2) Display Current Map displays the Current map.
3) Create New Map creates a new map.
4) Remove Current Map restores the default map as the Current map.
106
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
■
■
■
5) Edit Current Map changes Current map settings.
6) Clone Current Map copies the Current map.
7) Edit Host List for Current Map changes the host information for the
Current map.
■
8) Display Device List displays the device list.
Because each menu option includes a menu or sample screen display, each menu
option is discussed in the following separate sections.
Changing to the Next Bus
To scroll to the next SCSI bus, press Enter.
Selecting the Current Map
In the Device Mapping Configuration Menu, choose 1) Select Current Map to
select the Current map for each port or bus.
When this option is selected, the Select Current Map screen is displayed. The
current map assignment is displayed at the top of the screen (see Figure 51).
Figure 51: Select Current map
To indicate which map is to be the Current map, type the number that corresponds
to the desired map.
Network Storage Router N1200 User Guide
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Viewing the Current Map
In the Device Mapping Configuration Menu, choose 2) Display Current Map to
view the entries for the Current Map.
The Current Map Display screen is displayed.
Depending on whether a Fibre Channel map or a SCSI map was selected, the
screen display will differ. Figure 52 below, and Figure 53 on page 109 are
illustrations of the different screen displays for Fibre Channel maps and SCSI
maps.
Figure 52: FCP Current Map display
Note: The entire list may not fit on one screen. Press N or P to go back and forth
between screens.
108
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Figure 53: SCSI Current Map display
Note: The entire list may not fit on one screen. Press N or P to go back and forth
between screens.
Creating a New Map
In the Device Mapping Configuration Menu, choose 3) Create New Map to
create a new map for the port or bus.
The Create New Current Map subscreen is displayed.
At the prompt, enter a name for the new map. When a new map is created, it
automatically becomes the Current Map.
Removing the Current Map
In the Device Mapping Configuration Menu, choose 4) Remove Current Map to
remove the Current map and restore the default map as Current.
Network Storage Router N1200 User Guide
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Editing the Current Map
In the Device Mapping Configuration Menu, choose 5) Edit Current Map to edit
the current map.
The Map Edit Menu subscreen is displayed (see Figure 54).
Note: Auto-Assigned and SCC Maps cannot be edited.
Figure 54: Map Edit Menu
Map Edit Menu options:
■
■
■
■
1) Edit Name (changes the name of the current map.
2) Edit Map Entries (changes the content of the current map.
3) Clear Map (erases all entries from the current map.
4) Fill Map (automatically completes the entries for the current map.
Each editing option is discussed in the following sections.
Changing the Name of the Current Map
To change the name of the current map, in the Map Edit Menu, select 1) Edit
Name. Enter the new name at the prompt.
Note: Only user-defined map names can be changed.
110
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Editing the Map Entries of the Current Map
To edit the details of the Current map, in the Map Edit Menu, choose 2) Edit Map
Entries. This editing screen allows the user to navigate up and down the map
entries and create or remove entries. Device lists are also available to make it
easier to identify the device to be mapped.
Although the options are the same for editing Fibre Channel and SCSI maps, the
screen displays differ.
Figure 55 is an example of a screen display for Fibre Channel maps and Figure 56
on page 112 is an example of a screen display for a SCSI map.
Figure 55: Edit Map Entries for a Fibre Channel map
Network Storage Router N1200 User Guide
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Figure 56: Edit Map Entries for a SCSI map
Edit Map Entries options:
■
■
■
■
■
■
■
Next (N) scrolls down the list of map entries.
Previous (P) scrolls up the list of map entries.
Add (A) adds new map entries.
Create (C) creates a new map entry for a newly added device.
Remove Gaps (R) removes gaps in the listed sequence of LUN.
Delete (D) deletes a map entry.
Exit (X) returns to the previous menu.
Scrolling between Display Pages of the Edit Map Entries Screen
To scroll up and down the map entries, select P or N.
112
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding a Map Entry to a Fibre Channel Map
To add a new entry to a Fibre Channel map:
1. In the Map Edit Entries screen, select Add (A) (see Figure 57).
Figure 57: Adding an Entry to a Fibre Channel map
2. Enter the desired LUN ID.
If the selected LUN is already present in the map, a prompt is displayed that
asks to either confirm the override or enter different address information.
A device selection list is automatically generated.
Note: Devices cannot be mapped to their native port.
3. To select the map entry to edit, enter the number from the left-hand column of
the Port Map Edit Display screen (see Figure 58).
Figure 58: Device List generated for a Fibre Channel port
4. In the Device List, to add a listed device to the map, enter the number from the
If the selected device is already mapped, an error message will appear,
warning about adding a duplicate device.
Network Storage Router N1200 User Guide
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Adding a Map Entry to a SCSI Map
To add a new entry to a SCSI map:
1. In the Edit Map Entries screen, select Add (A) (see Figure 59).
Figure 59: Adding an Entry to a SCSI map
2. Enter a Target/LUN ID combination.
If the selected Target/LUN is already present in the map, a prompt is
displayed that asks to either confirm the override or enter different address
information.
A device selection list is automatically generated (see Figure 60).
Note: Devices cannot be mapped to their native port.
Figure 60: Device List generated for a SCSI port
114
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Note: A target ID must be defined in the SCSI Configuration to add devices.
3. In the Device List, to add a device to the map, enter the number from the
“Num” column.
If the selected device is already mapped, an error message will appear,
warning about adding a duplicate device.
Note: If a device with LUN = “-‘ is selected, all LUNs for this Target will be added to the
map.
Creating a Map Entry for a Fibre Channel Map
To pre-enter a map entry for devices that are not yet online, select Create (C).
Note: All essential information about the device must be known.
A series of questions is displayed. The questions will vary based on the “Current”
map protocol. Required information includes the LUN address, protocol, port,
device name, and device type (see Figure 61).
Figure 61: Creating a Map Entry for a Fibre Channel map
Network Storage Router N1200 User Guide
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Note: If the device being added is a SCSI device, the Target ID and LUN ID must be
entered. The Target ID must already be defined in the SCSI configuration.
Creating an Entry for a SCSI Map
To pre-enter a map entry for devices that are not yet online, select Create (C).
Note: All essential information about the device must be known.
A series of questions is displayed. The questions will vary based on the “Current”
map protocol. Required information includes the Target ID and LUN address,
protocol, port, device name, and device type must be entered (see Figure 62).
Figure 62: Creating an Entry for a SCSI map
116
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Note: If the device being added is a Fibre Channel device, the Node WWN, Port
WWN, and LUN ID must be entered.
Note: If this device is a duplicate of a device currently present in the device list, an error
message will be displayed.
Removing Gaps in the Map
To remove any incremental gaps in the sequence of LUN listed in the table, in the
Edit Map Entries screen, select Remove (R).
As the system removes any gaps from the table, the LUN are renumbered in
sequential order, starting with LUN 0.
Note: Some operating systems require gaps be removed in the mapping table in order
to detect all devices.
Deleting a Map Entry
To delete an entry from a map, in the Edit Map Entries screen, select Delete (D).
For Fibre Channel maps, at the prompt, either enter the LUN ID of the LUN to
delete or enter D to delete multiple LUN.
For SCSI maps, at the prompt, enter the Target ID and LUN ID of the LUN to
delete or enter D to delete multiple LUN.
Clearing the Entries from the Current Map
To remove all entries from the Current map, in the Edit Map Entries screen, select
3) Clear Map. A confirmation prompt is displayed.
Network Storage Router N1200 User Guide
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Filling in the Current Map
To instruct the system to automatically fill in the Current map, in the Edit Map
Entries screen, select 4) Fill Map.
All new devices are added to the end of the Current map.
After this operation is completed, the Edit Map Entries Menu is redisplayed.
Note: Devices marked DOWN are not mapped.
Cloning the Current Map
In the Device Mapping Configuration Menu, choose 6) Clone Current Map to
make an exact copy of the Current map. Assign a unique name to the new map.
After the cloning process is complete, the clone becomes the Current map.
Note: Auto Assigned maps and SCC maps cannot be cloned.
Editing the Host List for the Current Map
In the Device Mapping Configuration Menu, choose 7) Edit Host List for
Current Map to edit the host list for the Current map.
The Current map can be associated with hosts available in the host list on the same
port where the map is defined. Initially all hosts are associated with an Auto
Assigned map. These are built at runtime hosts and cannot be edited or deleted.
118
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Although the options are the same for FCP maps and SCSI maps, the screen
display differs. Figure 63 and Figure 64 are examples of the Host List Display
screens for FCP and SCSI maps.
Figure 63: Host List Display for Fibre Channel maps
Figure 64: Host List Display for SCSI maps
Host List Edit Display options:
■
■
■
■
■
■
Next (N) scrolls down the Host List.
Previous (P) scrolls up the Host List.
Add (A) adds a new host to the Host List.
Delete (D) deletes a host from the Host List.
Exit (X) returns to the previous menu.
Each of the options is discussed in the following paragraphs.
Network Storage Router N1200 User Guide
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Scrolling between the Display Pages of the Host List Edit Screen
To scroll up and down the host entries, select P or N.
Selecting a Host
To select a host from the list, enter the number displayed in the “N#” or the
“Num” column at the left of the screen.
Adding a Host to the Host List
To add a host to the Host List, select Add (A).
If the host is an FCP host, the Host Name, Host ID, port WWN, and Node WWN
for FCP host must be entered. (WWN values are hexidecimal) (see Figure 65).
Figure 65: Adding a Host to the Host List - FCP host
If the host is a SCSI host, the host name and the initiator ID must be entered
Figure 66 is an example of the screen display when a host is added to the Host List
of a of a SCSI host.
Figure 66: Adding a Host to the Host List - SCSI host
Deleting a Host from the Host List
To remove a host from the Host List, select Delete (D). After entering the number
of the host to delete, a confirmation prompt is displayed.
120
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Editing Host information
To change host information, select Edit (E).
Current host information is displayed on the screen. The system will display a
series of prompts, allowing changes to be entered.
Figure 67 is an example of the screen display for editing host information for a
Fibre Channel port, and Figure 68 on page 122 is an example of the screen display
for editing host information for a SCSI bus.
Note: To retain the current information for a prompt, press Enter at the prompt.
Figure 67: Editing Host Information on a Fibre Channel port
Network Storage Router N1200 User Guide
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Displaying the Entire Device List
In the Device Mapping Configuration Menu, choose 8) Display Device List to
view the entire device list for all buses and ports.
The Entire Device List screen is displayed (see Figure 69).
Figure 69: Entire Device list
Note: The entire list of maps may not fit on one screen. Select N or P to go back and
forth between screens displaying more maps. Select X to return to the previous menu.
Network Storage Router N1200 User Guide
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Trace and Event Settings Configuration
In the Configuration Menu, choose 5) Trace and Event Settings Configuration
to view and change Trace and Event settings. When this option is selected, the
following menu is displayed (see Figure 70).
Figure 70: Utility Settings (Trace Settings) Menu
Trace Settings Menu options:
■
1) Trace Settings Configuration configures the trace settings.
2) Event Settings Configuration configures the event settings.
■
Each of these options is discussed in the following sections.
Configuring Trace Settings
In the Utility Trace Settings Menu, 1) Trace Settings Configuration is used to
modify trace levels. Two pages of trace level settings are displayed. Figure 71 and
Figure 72 on page 125 are illustrations of the two Trace Settings screens.
Note: Trace Settings should not be modified in normal operation; performance
degradation may result.
1. To change any of the settings in these screens, enter the number that
corresponds to the option that needs to be changed.
2. The current setting is toggled to either On or Off.
3. Repeat Step 2 for each setting that needs to be changed in the page.
4. Before leaving the page, activate the new setting by entering U) Update
Current Operating Trace levels.
5. This option forces the currently displayed trace settings to become effective
immediately, without requiring a reboot or power cycle.
124
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Figure 71: Trace Settings screen
6. Press Enter to display the second Trace Settings page.
7. Figure 72 is an illustration of the second Trace Settings page.
8. If needed, change the settings in the second Trace Settings page.
Note: Be sure to set the clock and date in the Real-Time Clock Configuration Menu so
that event logging is accurate.
Figure 72: Trace Settings screen, continued
Network Storage Router N1200 User Guide
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Configuring Event Settings
In the Utility Trace Settings Menu, 2) Event Settings Configuration is used to
modify event filters (see Figure 73).
Figure 73: Event filter settings
Note: The asterisk in the screen display denotes the current setting.
1. To change any of the settings in this screen, enter the number of the desired
setting (1, 2, 3, or 4) that corresponds to the option that needs to be changed.
Settings include:
■
■
■
■
1) Log All Events
2) Disable Event Logging
3) Error Events
4) Notify Events
2. Before leaving the page, activate the new setting by entering U) Update
Current Operating Trace levels.
3. This option forces the currently displayed trace settings to become effective
immediately, without requiring a reboot or power cycle.
Note: Set the clock and date in the Real Time Clock Configuration Menu so that event
logging is accurate.
126
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Real-Time Clock Configuration
In the Configuration Menu, choose 7) Real-time Clock Configuration to change
the system time and date (see Figure 74).
Figure 74: Clock Setup Menu
1. To change the date or time, select 1) Set clock.
2. A series of prompts are displayed, allowing setup of:
■
■
■
24-hour time
Current date
Current day of the week
Network Storage Router N1200 User Guide
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Active Fabric Configuration
In the Configuration Menu, select 8) Active Fabric Configuration to enter Active
Fabric options (see Figure 75).
Figure 75: Active Fabric Configuration Menu
Active Fabric Configuration Menu options:
■
1) Toggle Server-Free Backup Mode changes the Server-free Backup
setting. Options include On and Off.
When set to On, server-free backup capability is enabled to accept Extended
Copy commands.
■
2) Change the number of controller LUN (default: 1) changes the number
of controller LUN.
This setting is a number in the range of 0 through 4.
Note: For Server-Free Backup Mode functionality, if addressing a Controller LUN is
desired, at least one controller LUN must be enabled and included in a relevant map.
is also enabled.
For more information on controller LUN and Extended Copy commands, see
Appendix B, “Controller LUN Commands.”
For information about server-free backup, see “Introduction” on page 17.
128
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Save Configuration
In the Configuration Menu, A) Save Configuration is used to save any
configuration changes.
The current configuration state is saved in FLASH, which updates the previous
configuration. This configuration is retained across future device resets or power
cycles.
Restore Last Saved Configuration
In the Configuration Menu, B) Restore Last Saved Configuration is used to
revert to the previous configuration. This can be useful when configuration
changes have been made, and the user wishes to return to the previous
configuration.
Reset and Save Configuration to Factory Defaults
In the Configuration Menu, choose C) Reset and Save Configuration to Factory
Defaults to reset the router configuration to its initial settings.
Network Storage Router N1200 User Guide
129
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
System Utility Menu
Accessed from the router Main Menu, the System Utility Menu is primarily used
to view system information.
To access the System Utilities Menu, in the router Main Menu, choose 2) System
Utilities (see Figure 76).
Figure 76: System utilities
System Utility Menu options:
■
■
■
1) System Statistics Menu displays a variety of system status information.
2) Event Log displays the system Event Log.
3) Enter System Diagnostics Mode performs Ethernet, SCSI, and Fibre
Channel connection tests.
This option is reserved for service personnel and is not documented.
4) Special Fibre Channel Link States performs special diagnostics.
This option is reserved for service personnel and is not documented.
■
The System Statistics Menu and the Event Log options are discussed in the
following separate sections.
130
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
System Statistics
In the System Utility Menu, select 1) System Statistics Menu to view system
status information (see Figure 77).
Figure 77: System Statistics Menu
System Statistics Menu options:
■
1) Display System Status displays router status information.
■
2) Display Fibre Channel Protocol Status displays Fibre Channel status
information.
■
3) Display Parallel SCSI Protocol Status displays SCSI status information.
Because each option offers a variety of display screens, each of these menu
options is discussed in the following separate subsections.
Viewing System Status Information
In the System Statistics Menu, choose 1) Display System Status to view a variety
of status information, including memory statistics, current active tasks, and stack
usage.
The System Status Menu is displayed (see Figure 78).
Figure 78: System Status Menu
Network Storage Router N1200 User Guide
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
System Status Menu options:
■
■
■
■
1) Display memory statistics displays memory usage information
2) Display active tasks displays a list of current tasks.
3) Display stack usage displays current stack information.
Viewing Fibre Channel Status Information
To display Fibre Channel status information, in the System Statistics Menu,
choose 2) Display Fibre Channel Protocol Status. The Fibre Channel Status
Menu is displayed (see Figure 79).
Figure 79: Fibre Channel Status Menu
The Fibre Channel Status Menu lists the following options:
■
■
■
■
1) Display Fibre Channel Link Status displays Fibre Channel link
information.
2) Display Attached Fibre Channel Devices displays a list of devices
attached to this Fibre Channel port.
3) Display Fibre Channel Resource Status displays Fibre Channel resource
transport information.
4) Display Fibre Channel Driver Resource Status displays Fibre Channel
driver information.
Each menu option and example screen displays are discussed in the following
subsections.
132
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Viewing Fibre Channel Link Information
To see link statistics for the Fibre Channel port:
1. 1) In the Fibre Channel Status Menu, choose Display Fibre Channel Link
Status.
The following page is displayed (see Figure 80).
See Table 9 for a list of term definitions.
Figure 80: Fibre Channel Link Status screen
2. A) To refresh the screen display, select Autorepeat.
Table 9: Link Status Definitions
Link Status Field
Definition
LinkState
Current Fibre Channel link status
AL_PA
Arbitrated loop physical address
InDevDataSeqs
OutDevDataSeq
InLnkDataSeqs
OutP_BSYFrms
Number of Device Data sequences received by this port
Number of Device Data sequences transmitted by this port
Number of Link Data frames received by this port
Number of P_BSY frames received by this port
Number of P_BSY frames transmitted by this port
Network Storage Router N1200 User Guide
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Table 9: Link Status Definitions
Link Status Field
InF_BSYFrames
InP_RJTFrames
OutP_RJTFrame
LinkDowns
Definition
Number of F_BSY frames received by this port
Number of P_RJT frames received by this port
Number of P_RJT frames transmitted by this port
Number of Link Down conditions detected
Number of ABTS frames received
InABTSs
OutABTSs
Number of ABTS frames transmitted
Number of laser faults detected
LaserFaults
SignalLosses
SyncLosses
Number of times Loss of Signal was detected
Number of times Loss of Sync was detected
Number of bad characters received
BadRxChars
LinkFailures
Number of Link Failure conditions
BadCRCFrames
ProtocolErrs
Number of frames received with a bad CRC
Number of protocol errors detected
BadSCSIFrames
Number of BAD SCSI frames detected
134
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Viewing Attached Fibre Channel Devices
To view a list of the devices attached to this port:
1. In the Fibre Channel Status Menu, choose 2) Display Attached Fibre
Channel Devices (see Figure 81).
Figure 81: Fibre Channel Device Display page
2. To refresh the display, select R) Refresh Device Display.
Note: In Router-to-Router (R2R) configurations, only the first device of all the attached
devices will be shown. To see all of the devices in R2R configurations, use Visual
Manager.
3. To view device details, select D) Display Device Details.
Viewing Fibre Channel Resource Transport Information
To view FCP transport information, in the Fibre Channel Status Menu, choose
3) Display Fibre Channel Resource Status.
Network Storage Router N1200 User Guide
135
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
The FCP Transport Queues page is displayed.
The FCP Transport Queue page has no options. It is used only for viewing
resource status (see Figure 82).
Figure 82: FCP Transport queues
Viewing Fibre Channel Driver Status Information
To display Fibre Channel Driver Queue information, in the Fibre Channel Status
Menu, select 4) Display Fibre Channel Driver Resource Status.
The Fibre Channel Driver Queues page is displayed (see Figure 83).
The Fibre Channel Driver Queues page has no options. It is used only for viewing
Fibre Channel driver resources.
Figure 83: Fibre Channel Driver resource status
136
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Viewing SCSI Status Information
To display SCSI status information, in the System Statistics Menu, choose
3) Display Parallel SCSI Protocol Status.
The Parallel SCSI Protocol Status Menu is displayed (see Figure 84).
Figure 84: SCSI Status Menu
SCSI Status Menu options:
■
■
■
1) Display SCSI Statistics (displays SCSI statistics.
2) Display Attached SCSI Devices displays attached SCSI devices.
3) Display SCSI Resource Status displays SCSI resource status.
Each option is discussed in the following paragraphs.
Viewing SCSI Statistics
To view the SCSI status page, in the SCSI Status Menu, choose 1) Display SCSI
Statistics. There are no options in this display screen.
Viewing Attached SCSI Devices
To see a list of the devices attached to this SCSI bus in the SCSI Status Menu,
choose 2) Display Attached SCSI Devices.
The SCSI Device Display Menu is displayed (see Figure 85).
Figure 85: SCSI Device Display Menu
Network Storage Router N1200 User Guide
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
SCSI Device Display Menu options:
■
1) Issue discovery for all buses issues a discovery command for all SCSI
buses.
■
2) Issue discovery for selected bus issues a discovery command for the
selected bus.
■
■
■
3) Issue boot discovery issues a boot discovery command.
4) Display all local devices displays a list of local devices for all buses.
5) Display local devices on specified bus displays a list of local devices for
the selected bus.
To display SCSI resource information, in the SCSI Status Menu, choose
3) Display SCSI Resource Status.
The SCSI Resource Display page is displayed. There are no options in the SCSI
Resource Display. It is used only for viewing SCSI resource status
(see Figure 86).
Figure 86: SCSI Resource display
138
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Event Log
In the System Utilities Menu, 2) Event Log is used to view and clear the system
Event Log (see Figure 87).
Figure 87: Event Log Menu
Event Log Menu options:
■
1) Display event log displays the Event Log.
■
2) Clear event log deletes all entries from the Event Log.
Trace Dump Menu
In the router Main Menu, 3) Display Trace and Assertion History is used to
manage trace history information (see Figure 88).
Figure 88: Trace Dump Menu
Trace Dump Menu options:
■
■
1) Display trace for current boot cycle displays current boot cycle trace
history information.
2) Display trace from previous boot cycle displays previous boot cycle trace
history information.
information from the last assertion failure.
Network Storage Router N1200 User Guide
139
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
■
■
4) Clear current trace buffer clears the current trace buffer.
5) Clear (flash) assert trace buffer clears the assertion failure trace buffer.
Saving Copies of the Trace Buffers using FTP
Using an FTP session, the trace buffers from the router can be copied and saved.
1. Verify the router is connected to the Ethernet network.
2. Start an FTP session.
3. Enter the router IP address at the FTP prompt:
ftp <IP address>
Note: Initially, the factory default router IP address is 1.1.1.1. To view the current IP
address, navigate to the Ethernet Configuration Menu and view the screen display. See
the “Configuration Menu” section for information on viewing and changing the router
IP address.
4. Specify the directory location on the computer or network where the FTP
program will store the trace file.
5. Enter the user name and password.
The factory default user name is rootand the default password is password.
6. Specify Bin mode:
bin
7. Enter the appropriate command to copy the current or previous trace buffer:
— To copy the current trace buffer:
get curtrace.txt
— The file will transfer from the router.
— To copy the previous trace buffer:
get prvtrace.txt
— The file will transfer from the router.
140
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Reboot Option
To reboot the router, in the Main Menu, select 4) Reboot.
After this option is selected, a confirmation prompt is displayed. If a positive
response is given to the confirmation message, the router is restarted.
Note: Current router activities will be disrupted during a reboot.
Network Storage Router N1200 User Guide
141
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet User Interface
Download New Firmware Option
To download a new version of the firmware:
1. Select 5) Download a New Revision of the Firmware in the router Main
Menu.
A confirmation prompt is displayed.
2. Respond to the confirmation prompt.
3. Select Transfer, Send File in the terminal emulator utility.
4. Select the location of the firmware.
If necessary, use Browse to search for the file.
5. Select XMODEM as the transfer protocol.
6. Press the Send button.
The firmware will begin downloading to the router.
When the download process is complete, the system verifies that the firmware
image was successfully written to the FLASH memory and reboots. When the
router is rebooted, it detects that there is a newly downloaded firmware image,
copies that image to the boot sector of the FLASH, and boots using the new
image.
Figure 89 is an illustration of the Download Firmware Menu after a new
version of the firmware has been loaded.
Figure 89: Download Firmware Menu
142
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP User Interface
5
The following tasks can be managed through an FTP interface and are discussed
in this chapter:
■
■
■
■
Access the FTP UI, page 144
Backup and Restore Configuration Settings, page 145
Copy Trace Buffers, page 147
Upgrade Firmware, page 148
Network Storage Router N1200 User Guide
143
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP User Interface
Access the FTP UI
To access the router using an FTP UI:
1. Connect the router to the Ethernet network used by the host computer.
2. Start an FTP session using the router IP address:
ftp <IP address>
where IP address is the IP address of the router.
The default router IP address is 1.1.1.1.
Note: You may also need to specify the external directory location where your FTP
utility will store the backup configuration file.
3. Enter the user name and password.
The default user name is rootand the default password is password.
144
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP User Interface
Backup and Restore Configuration Settings
The router supports the backup and restore of configuration settings over FTP.
This allows multiple configuration files to be maintained in a location external to
the router. When backing up a configuration, the settings are saved from the flash
memory on the router to a binary file in an external location determined by the
user.
Backing up the Router Configuration
To backup the router configuration settings:
1. Connect the router to the Ethernet network used by the host computer.
2. Start an FTP session using the router IP address:
ftp <IP address>
where IP address is the IP address of the router.
The default router IP address is 1.1.1.1.
Note: You will need to specify the external directory location where your FTP utility is to
store the backup configuration file.
3. Enter the user name and password.
The default user name is rootand the default password is password.
HP recommends that the user name and password be changed from the default
values.
4. Specify binary mode:
bin
5. Specify the filename (with the extension .cfg) using the get command:
get filename.cfg
The file will transfer to the user-specified location.
and Ethernet physical address (MAC address) values are not saved in the configuration
file. All other configuration settings are saved.
Network Storage Router N1200 User Guide
145
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP User Interface
Restoring the Router Configuration
To restore a configuration to the router:
1. Connect the router to the Ethernet network used by the host computer.
2. Start an FTP session using the router IP address:
ftp <IP address>
where IP address is the address of the router.
The default IP address of the router is 1.1.1.1.
3. Enter the user name and password.
The default user name is rootand the default password is password.
HP recommends that the user name and password be changed from the default
values.
4. Specify binary mode:
bin
5. Specify the configuration’s path and filename (with the filename extension
.cfg) using the put command:
put <path:filename.cfg>
The file is transferred to the router. After the file transfer is complete, router
will automatically reboot. When the router completes the POST process, it
will use the restored configuration.
Note: When restoring a configuration, World Wide Name (WWN) values and
Ethernet physical address (MAC address) values revert to the factory default settings.
User defined values for these settings are not retained and must be re-entered after the
restoration of the configuration is complete.
Note: Confirm the restored configuration by verifying that the settings are correct.
146
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP User Interface
Copy Trace Buffers
Use the following procedure to save copies of the trace buffers:
1. Connect the router to the Ethernet network used by the host computer.
2. Start an FTP session using the router IP address:
ftp <IP address>
where IP address is the address of the router.
The default router IP address is 1.1.1.1.
Note: You will need to specify the directory location where your FTP utility will store the
trace file.
3. Enter the user name and password.
The default user name is rootand the default password is password.
HP recommends that the user name and password be changed from the default
values.
4. Specify binary mode:
bin
5. Specify the filename (with the extension .txt) using the get command.
For the current trace buffer, use the following command:
get curtrace.txt
For the previous trace buffer, use the following command:
get prvtrace.txt
Network Storage Router N1200 User Guide
147
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP User Interface
Upgrade Firmware
Use the following procedure for Windows-based systems to upgrade the router
firmware.
Note: A JAVA applet-based FTP utility is accessible from the UI.
1. Connect the router to the Ethernet network used by the host computer.
2. Start an FTP session using the router IP address:
ftp <IP address>
where IP address is the IP address of the router.
The default router IP address is 1.1.1.1.
3. Enter the user name and password.
The default user name is rootand the default password is password.
HP recommends that the user name and password be changed from the default
values.
4. Specify binary mode:
bin
5. Specify the path and filename (extension .dlx) of the firmware file to be
transferred by using the put command as shown:
put <path:filename.dlx>
The firmware file will be transferred and the router automatically reboots. The
firmware upgrade will be effective after POST process completes.
Note: Confirm the firmware level by checking the reboot messages through the serial
interface.
148
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Troubleshooting
6
This chapter discusses some basic methods of identifying faults in the setup and
Most problems are made during the initial installation of the router. Before
proceeding with advanced troubleshooting techniques, verify all connections and
review the configuration.
■
■
— Verifying the Host Configuration , page 153
— Verifying HBA Device Driver Information, page 154
— Verifying Serial Port Configuration, page 154
— Verifying PRLI Data, page 155
Network Storage Router N1200 User Guide
149
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Troubleshooting
LED Indicators
The LED indicators on the router are useful for diagnosing various problems:
■
The Fibre Channel port LEDs indicates Fibre Channel activity and link status.
If one of these indicators does not light or stays continually lit without any
corresponding SCSI bus activity, it may indicate a problem with the Fibre
Channel link. Verify the Fibre Channel configuration.
■
The SCSI bus LEDs indicates SCSI activity. These indicators are lit during
power up, configuration, and when the unit is transferring data. If the SCSI
indicator stays continually lit without any corresponding Fibre Channel LED
activity, it may indicate a problem with the SCSI bus configuration. Verify the
SCSI bus configuration.
■
The Ethernet LEDs indicates activity and link status. If one of these indicators
does not light or stays continuously lit, it may indicate a problem with the
network connection. Verify the network connection. The port must be
connected to a 10/100BaseT Ethernet network to function properly.
For additional information and illustrations of the specific LEDs see “External
Features Overview” on page 18.
150
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Troubleshooting
Basic Troubleshooting
If possible, simplify the installation by reducing it to the most basic configuration.
■
■
■
■
■
■
■
■
■
■
Verifying the Host Configuration , page 153
Verifying HBA Device Driver Information, page 154
Verifying Serial Port Configuration, page 154
Verifying PRLI Data, page 155
Each of these topics is discussed in the following sections.
Verifying SCSI Bus Configuration
Items to check include:
■
Termination — Problems with termination can cause intermittent or hard
failures. A SCSI bus must be terminated on both ends. Termination problems
are common when both narrow and wide devices are on the same bus.
■
Bus Type — On an LVD SCSI bus, SE and LVD devices can be connected to
the same bus. However, if one SE device is detected during power up,
communication to all devices will convert to SE mode.
■
■
Device ID — Each device on a SCSI bus must have a unique ID. Verify
configured IDs are not in use by other devices on the same SCSI bus.
Cabling — Check SCSI cables to verify they are functional. SCSI rules for
total length, distance between devices, and stub length must be followed.
Connections should also be checked and reseated if necessary.
■
SCSI Devices — Verify that the SCSI devices on a particular SCSI bus can
be seen in the Configuration Menu of the router. If the router cannot see the
devices, verify SCSI configuration, cabling, and termination.
Network Storage Router N1200 User Guide
151
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Troubleshooting
Verifying Fibre Channel Port Connection
If SCSI devices are recognized on the SCSI buses, but do not appear to the Fibre
Channel host, it may be that the Fibre Channel link is not properly established.
Most hubs and switches have link indicators showing link status. When the router
is connected and powered on, this link indicator should show a good link. If it
does not, check the cabling or connections.
One method of verifying link integrity when connected to a functional host,
involves disconnecting and then reconnecting the Fibre Channel cable. This
procedure should cause momentary activity of this indicator as the link
reinitializes.
Additionally, verify that the media type of the router and the attached hub, HBA,
or switch is of corresponding types. When using optical media, verify that the
attached device is using non-OFC type optical devices.
Note: By default, the Fibre Channel port speed is set to 1 Gbps. Changes to the Fibre
Channel port speed must be manually set, such as for 2 Gbps. If set incorrectly and
plugged into a Loop or Fabric, the unit may receive Framing errors due to the incorrect
Fibre Channel link speed.
Verifying SCSI Devices in Windows NT
If running Fibre Channel-to-SCSI mapping mode, verify the Fibre Channel and
the SCSI devices are recognized by the router.
Sometimes Windows NT may need to be rebooted with all SCSI devices and the
router powered up before recognizing the devices.
Verify the Fibre Channel and the SCSI devices:
■
To verify the Fibre Channel devices, navigate to the Windows NT Control
Panel, select SCSI Adapters, and double click the Fibre Channel HBA.
■
■
The SCSI devices should be listed.
If no devices are listed, verify the router configuration, Fibre Channel HBA
configuration, and cabling.
■
■
If devices are listed, verify the Fibre Channel HBA mapping mode or the
AL_PA addresses.
To verify the SCSI devices, navigate to the Windows NT Control Panel,
select SCSI adapters, and double click the SCSI controller.
152
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Troubleshooting
■
If no devices are listed, verify the router configuration, SCSI Controller
configuration, and cabling.
Verifying the Router Configuration
If you are in doubt about the configuration or about the location of the error,
restore the router to the factory default configuration and proceed to configure the
unit one step at a time, verifying the functionality of the configuration after each
change is made.
Caution: Restoring factory defaults overwrites user configurations. In the
serial/ Telnet interface, use the save configuration option before resetting
factory defaults to allow recovery of user configuration.
Verifying Mapping
If the router is working in Fibre Channel-to-SCSI Initiator mode and is using
Indexed or SCC mapping, try changing to Auto-assigned mapping.
Verifying Devices
It may be useful to connect the SCSI target devices directly to a SCSI interface
(for example, a host SCSI bus) to verify that the devices are functional.
Verifying the Host Configuration
In some cases, it may be that the Fibre Channel HBA or host device driver may
not be working properly. Check the configuration of these elements.
It may be useful to check the release notes for the device driver to see if there are
any specific issues or required configuration. It may also be useful to ensure that
the current version of the HBA driver is being used.
There are cases where older applications can have expectations about what
constitutes a valid SCSI ID, and thus may not correctly handle certain mappings.
This is not an issue for the operating system or most applications. However, some
applications may exhibit difficulties addressing target IDs greater than 15 (16 and
higher.) To resolve this situation, configure the router to use hard addressing and
set the AL_PA to a value that the HBA will be able to map with an ID less than
16.
Network Storage Router N1200 User Guide
153
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Troubleshooting
Verifying HBA Device Driver Information
Review the HBA device driver Readme.txt file for configuration specifics. An
HBA may require a different configuration. HBAs typically come with utility
programs to view or change their configurations.
Verifying Serial Port Configuration
Verify the configuration of the terminal or terminal emulation program.
Table 10: Terminal Configuration Settings
BAUD Rate
Autobaud, 9600, 19200, 38400, 57600, 115200
Data Bits
8
Stop Bit
1
Parity
None
Flow Control
XON/XOFF
If problems persist, verify the cabling.
If a valid Ethernet IP address is configured, serial configuration settings can also
be set via Telnet.
154
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Troubleshooting
Verifying PRLI Data
The router returns the PRLI (preliminary login) response data as specified in
Table 11.
In the default configuration, the router returns PRLI Data (PRLI Accept Payload)
with the Target bit SET and the Initiator bit CLEAR. However, some
configurations require the Initiator bit be SET, such as in router-to-router
configurations. See the Fibre Channel Overrides menu for more information about
changing the initiator bit.
Table 11: PRLI
Item
PRLI Command Code
Page Length
Value
0x20
0x10
0x10
0x8
0x0
0x0
0x0
0x1
0x1
0x0
0x0
0x1
0x1
0x0
0x0
0x1
0x0
Payload Length
Type Code
Type Code Extension
OPA
RPA
IPE
Response Code
Originator Process Associator
Responder Process Associator
Initiator Function
Target Function
Command/Data Mixed Allowed
Data/Response Mixed Allowed
Read XFER_RDY Disabled
Write XFER_RDY Disabled
Network Storage Router N1200 User Guide
155
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Troubleshooting
156
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial and Ethernet Pin
Assignments
A
This appendix provides details for:
■
RJ-11 Serial Pin Assignments, page 158
■
RJ-45 Ethernet Cable Pin Assignments, page 159
Network Storage Router N1200 User Guide
157
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial and Ethernet Pin Assignments
RJ-11 Serial Pin Assignments
The layout of the pin assignments for the serial receptacle on the router is
illustrated in Figure 90.
Figure 90: RJ-11 Serial pin assignments
6
5
4
3
2
1
Fibre
Link/
Channel
Act
1
Pwr.
Ethernet
The pin definitions listed in Table 12 correspond to the pin assignments in
Figure 90.
Table 12: RJ-11 Serial Pin Assignments
Item
Description
1
2
3
4
5
No connection
Serial common (ground)
Transmit data
Receive data
CTS (clear to send)
Note: To connect the router to a host system, use a RS-232 null modem cable.
158
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial and Ethernet Pin Assignments
RJ-45 Ethernet Cable Pin Assignments
The layout of the pin assignments for RJ-45 Ethernet receptacle is illustrated in
Figure 91.
Figure 91: RJ-45 Ethernet pin assignments
1
2
3
4
5
6
7
8
Fibre
Channel
Link/
Act
Pwr.
1
Ethernet
The pin definitions listed in Table 13 correspond to the pins assignments in
Figure 91.
The router Ethernet connection supports the IEEE specifications for 10BASE-T
and 100BASE-TX Ethernet standards.
Table 13: RJ-45 Ethernet Pin Assignments
Item
Description
1
2
3
4
5
6
7
8
Transmit Out +
Transmit Out -
Receive in +
No Connection
No Connection
Receive in -
No Connection
No Connection
Network Storage Router N1200 User Guide
159
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial and Ethernet Pin Assignments
160
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller LUN Commands
B
The HP StorageWorks Network Storage Router supports and executes the set of
SCSI-3 commands listed in this Appendix. These commands can be received as
Complete definitions of SCSI-3 commands can be found in the SCSI-3 standard
available from the American National Standards Institute (ANSI).
This document divides Controller LUN commands into two categories:
■
General Commands, page 162
■
Copy Manager Commands, page 166
To first determine which router LUNs are controller LUNs and which are device
LUNs, the host software must use the Inquiry general command.
Controller LUNs are addressable in all addressing modes. In SCC mode, there is
one controller LUN. In Auto-Assigned and Indexed modes, there can be up to four
configurable controller LUNs.
To access Copy Manager or other general management features, the commands
must be sent to the router controller LUNs.
To initiate Extended Copy operations (a subset of Copy Manager), the commands
can be sent to any tape device LUN attached to the router. The four controller
LUNs allow the host software to run multiple concurrent Extended Copy
commands.
Note: Controller LUNs are numbered in sequence following the last device LUN,
without any gaps. A controller LUN may be placed anywhere in custom tables.
Network Storage Router N1200 User Guide
161
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller LUN Commands
General Commands
■ Report LUNs
■ Inquiry
Each of these commands is discussed in the following paragraphs.
Report LUNs Command
The Report LUNscommand returns a list of LUNs that can receive commands.
The format of the Report LUNscommand is shown in Table 14.
Table 14: Format of Report LUNs Command
Bit/
Byte
0
7
6
5
4
3
2
1
0
Operation Code (Example: 0xA0)
1
Reserved
2
Reserved
3
Reserved
4
Reserved
5
Reserved
6
Most Significant Byte (MSB)
Allocation Length
7
8
9
Least Significant Byte (LSB)
Reserved
10
11
Control Byte
The router returns the LUN Parameters as defined in Table 15.
Table 15: Report LUNs Data
Bit/
Byte
7
6
5
4
3
2
1
0
0
Most Significant Byte (MSB)
LUNs Length List
1
2
162
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller LUN Commands
Table 15: Report LUNs Data
Bit/
Byte
7
6
5
4
3
2
1
0
3
Least Significant Byte (LSB)
4
Reserved
Reserved
Reserved
Reserved
5
6
7
All LUNs are reported and will appear in the host map.
Note: In addition to the device LUNs, controller LUNs are also included in the report.
report peripheral device types as 0x0c.
Inquiry Command
The format of the InquiryCommand is shown in Table 16.
Table 16: Format of LUN Inquiry Command
Bit/
Byte
7
6
5
4
3
2
1
0
0
Operation Code (Example: 0x12)
1
Reserved
EVPD
2
Page Code or Operation Code
Reserved
3
4
Allocation Length
Control
5
Network Storage Router N1200 User Guide
163
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller LUN Commands
EVPD Page 0x80
If the EVPD bit (bit 0 of byte 1) is set and the Page Code is 0x80, the unit serial
number page is returned. The format of this page is shown in Figure 17.
Table 17: Format of EVPD Page 0X80
Bit/
Byte
0
7
6
5
4
3
2
1
0
Device Type (Example: 0x0c)
Page Code (80h)
Reserved
1
3
4
Page Length
5
Serial Number
The router returns the LUN Inquiry Data as defined in Table 18
Table 18: LUN Inquiry Data
Item
Peripheral Qualifier
Peripheral Device Type
RMB
Value
0x00
0x0C – Indicates Router/Router function
0x00
Device Type Qualifier
ISO Version
AENC
0x00
0x00
0x00
TrmIOP
0x00
Response Data Format
Additional Length
RelAdr
0x02 – SCSI-2 Inquiry Data Format
0x20
0x00
0x00
0x00
0x00
0x00
0x00
Wbus32
Sync
Linked
CmdQue
SftRe
164
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller LUN Commands
Table 18: LUN Inquiry Data
Item
Vendor ID
Value
“HP”
Product ID
“router”
“XXXXXX”
Revision Level
The router will only reply to a SCSI Inquiry using 8-byte LUN field of 0x00.
Note: The Revision Levelcomes from the last four characters of the build string,
which appears in the headings for most menu screens.
Network Storage Router N1200 User Guide
165
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller LUN Commands
Copy Manager Commands
To access Copy Manager or other general management features, the commands
must be sent to the router controller LUNs. The following controller LUN
commands can be used for Copy Manageron the router:
■ Extended Copy
■ Receive Copy Results
■ Mode Sense (6) and Mode Sense (10)
Each of these commands is discussed in the following paragraphs.
Extended Copy Command
The router supports Extended Copycommands in the following two formats:
■
Version 99-143r1
Version SPC-2
■
To initiate Extended Copyoperations, the commands can be sent to any tape
commands can be active.
Version 99-143r1
The Extended Copycommand supports the following Target descriptor codes
listed in Table 19:
Table 19: Extended Copy Target descriptor codes, version 99-143r1
Item
Value
Fibre Channel World Wide Name
Target Descriptor
0xE0
0xE1
Fibre Channel N_Port Target
descriptor
166
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller LUN Commands
The Extended Copycommand supports the following Initiator descriptor
codes listed in Table 20:
Table 20: Extended Copy Initiator descriptor codes, version 00-143r1
Item
Block to Stream
Stream to Block
Block to Block
Inline to Stream
Stream to Discard
Verify Target
Value
0x00
0x01
0x02
0x04
0x06
0x07
0x11
0x12
Space Operation
Locate Operation
Version SPC-2
The Extended Copycommand supports the following Target descriptor codes
listed in Table 21:
Table 21: Extended Copy Target descriptor codes, version SPC2
Item
Value
Fibre Channel World Wide
Name Target Descriptor
0xE0
0xE1
Fibre Channel N_Port Target
Descriptor
The Extended Copycommand also supports the following Initiator descriptor
codes listed in Table 22:
Table 22: Extended Copy Initiator codes, version SPC2
Item
Block to Stream
Stream to Block
Stream to Stream
Inline Data to Stream
Value
0x00
0x01
0x02
0x03
0x04
Network Storage Router N1200 User Guide
167
Download from Www.Somanuals.com. All Manuals Search And Download.
Controller LUN Commands
Table 22: Extended Copy Initiator codes, version SPC2
Item
Value
Stream to Discard
Verify Target
0x06
0x07
0x08
0x0f
Block with Offset to Stream
Stream to Discard + Hold
Space Operation
0x11
0x12
Locate Operation
Receive Copy Results Command
The router supports the Receive Copy Results command, used to return
the results of a previous or current Extended Copycommand. The Receive
Copy Resultscommand supports the following mode listed in Table 23:
Item
Value
Copy Status
0x00
The Receive Copy Resultscommand also supports the following service
actions listed in Table 24:
Table 24: Receive Copy Results command, service actions
Item
Value
Copy Status
Receive Data
0x00
0x01
0x03
0x04
Operating Parameters
Failed Segment Details
Mode Sense (6) and Mode Sense (10) Commands
The router supports the Mode Sense (6) and Mode Sense(10) commands,
168
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Addressing Methods and
Table Structures
C
Fibre Channel and SCSI systems use different methods of addressing devices. The
router has a method of translating device IDs so each SCSI device is mapped to
the appropriate Fibre Channel LUN. The SCSI buses establish the bus connections
between devices. Targets on a SCSI bus may internally address LUNs. The
addressing of a specific SCSI device is represented by the BUS:TARGET:LUN
triplet.
When a Fibre Channel Initiator initializes on a loop, the host must first determine
what devices exist on the loop. Device discovery is performed and an FCP target
device list is built. Each device is queried for FCP LUNs (the LUNs are the actual
devices that the operating system will address.) The addressing used is the SCC
Logical Unit Addressing and Peripheral Device Addressing method, shown in
Table 25 through Table 28. First level addressing is supported, so only the first
two bits of the 8-bit FCP LUN are used.
Table 25: Addressing Sequence
Bit/Byte
N
7
6
5
4
3
2
1
0
Address Method
Address Method Specific
N+1
Address Method Specific
Table 26: Address Method Definitions
Code
00
Description
Peripheral Device Addressing Method
Volume Set Addressing Method
Logical Unit Addressing Method
01
10
Network Storage Router N1200 User Guide
169
Download from Www.Somanuals.com. All Manuals Search And Download.
Addressing Methods and Table Structures
Table 27: SCSI Logical Unit Addressing
Bit/Byte
N
7
6
5
4
4
3
3
2
2
1
1
0
0
1
0
Target
Table 28: Peripheral Device Addressing
Bit/Byte
N
7
6
5
0
0
Bus
N+1
Target/LUN
Depending on the configuration, the router supports the Peripheral Device
Addressing method and the Logical Unit Addressing method.
The data shown in Table 29 comes from the Fibre Channel Configuration Menu.
The administrator enters the node number (number to the left of the colon in
Table 29) and the router translates the node number into the corresponding
AL_PA value (number to the right of the colon in Table 29).
Table 29: Arbitrated Loop Node-Number to AL-PA Lookup Table
0:0x01
1:0x02
2:0x04
3:0x08
4:0x0F
5:0x10
6:0x17
7:0x18
8:0x1B
9:0x1D
10:0x1E
11:0x1F
12:0x23
13:0x25
14:0x26
15:0x27
21:0x2E
22:0x31
23:0x32
24:0x33
25:0x34
26:0x35
27:0x36
28:0x39
29:0x3A
30:0x3C
31:0x43
32:0x45
33:0x46
34:0x47
35:0x49
36:0x4A
42:0x52
43:0x53
44:0x54
45:0x55
46:0x56
47:0x59
48:0x5A
49:0x5C
50:0x63
51:0x65
52:0x66
53:0x67
54:0x69
55:0x6A
56:0x6B
57:0x6C
63:0x74
64:0x75
65:0x76
66:0x79
67:0x7A
68:0x7C
69:0x80
70:0x81
71:0x82
72:0x84
73:0x88
74:0x8F
75:0x90
76:0x97
77:0x98
78:0x9B
84:0xA6
85:0xA7
86:0xA9
87:0xAA
88:0xAB
89:0xAC
90:0xAD
91:0xAE
92:0xB1
93:0xB2
94:0xB3
95:0xB4
96:0xB5
98:0xB9
99:0xBA
105:0xC9
106:0xCA
107:0xCB
108:0xCC
109:0xCD
110:0xCE
111:0xD1
112:0xD2
113:0xD3
114:0xD4
115:0xD5
116:0xD6
117:0xD9
119:0xDC
120:0xE0
170
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Addressing Methods and Table Structures
Table 29: Arbitrated Loop Node-Number to AL-PA Lookup Table
16:0x29
17:0x2A
18:0x2B
19:0x2C
20:0x2D
37:0x4B
38:0x4C
39:0x4D
40:0x4E
41:0x51
58:0x6D
59:0x6E
60:0x71
61:0x72
62:0x73
79:0x9D
80:0x9E
81:0x9F
82:0xA3
83:0xA5
100:0xBC
101:0xC3
102:0xC5
103:0xC6
104:0xC7
121:0xE1
122:0xE2
123:0xE4
124:0xE8
125:0xEF
Network Storage Router N1200 User Guide
171
Download from Www.Somanuals.com. All Manuals Search And Download.
Addressing Methods and Table Structures
SCC (SCSI Controller Command) Addressing Method
When a router is configured to use SCSI Controller Command addressing (SCC)
and a command is received, the router either will respond as a controller device to
the FCP Initiator or will route the FCP request to a specified BUS:TARGET:LUN.
If a request using the Peripheral Device Addressing method is received (an FCP
command with the LUN field bits 7 and 6 of byte 0 set to 0), the router routes the
request to the internal processor, which acts on the command directly. If a request
using the Logical Unit Addressing method is received (bits 7 and 6 set to 00x10),
the request is routed to the BUS:TARGET:LUN as specified in the defined field
Host systems using SCC addressing will typically do initial device discovery
using the Peripheral Device Addressing method. On issuing an Inquiry command
to the router, the host will receive the router Inquiry data, indicating the device
type as a controller device (Inquiry data indicates device type is 0xC). The host
will then know that subsequent commands to router-attached devices will use the
Logical Unit Addressing method.
The host can perform discovery by either progressing through the
BUS:TARGET:LUN values, as would a standard SCSI driver, or by issuing a
Report LUNs command. This command is sent to the router (using the Peripheral
Device Addressing method). The router returns a table indicating the attached
devices. The host can then perform actions on these devices directly without
performing further discovery processing.
172
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Addressing Methods and Table Structures
Auto Assigned Addressing Method
The Auto Assigned addressing method is created through SCSI device discovery
on power up or reset. As the router performs device discovery on the SCSI bus,
the index table FCP LUN values are filled with adjacent FCP LUN referencing
each subsequent SCSI device. The index table generated by the Auto Assigned
option cannot be manually edited.
When the Auto Assigned option is used, the host system will detect every attached
SCSI device without voids, allowing full device access to the host. This method
allows easy configuration in environments where SCSI device ordering is not
important and where hot plugging of SCSI devices will not occur. For example,
tape libraries are excellent candidates for using Auto Assigned Addressing.
Configuration options provide for the SCSI discovery to be performed in order of
bus, target, or LUN as desired for the specific environment.
Network Storage Router N1200 User Guide
173
Download from Www.Somanuals.com. All Manuals Search And Download.
Addressing Methods and Table Structures
Indexed Addressing Method
Indexed addressing allows for host bus adapter (HBA) drivers that use only
Peripheral Device Addressing to access SCSI devices attached to the router. This
addressing is done by use of a table, which is indexed by sequential LUN values,
indicating the selected BUS:TARGET:LUN devices. In this mode, it is not
possible to address the router as a controller unit directly.
The maximum size of the table is equal to the number of buses multiplied by the
number of targets per bus less one Initiator ID per bus, multiplied by the number
of LUNs per target. The index table can be manually edited. A method is also
provided to perform SCSI device discovery and fill the index table.
See Table 30 for the Indexed addressing table.
Table 30: Indexed Addressing Table
FCP LUN Value
SCSI BUS:TARGET:LUN
0
1
2
3
4
5
6
0:0:0
0:1:0
0:2:0
0:3:0
0:4:0
0:5:0
0:6:0
(0:7:0 occupied by Initiator ID)
7
0:8:0
(...)
(...)
13
14
15
16
17
(...)
0:14:0
0:15:0
1:0:0
1:1:0
1:2:0
(...)
174
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance
Notices
D
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your
product has been assigned a unique HP Series Number. The series number can be
found on the product label, along with the required approval markings and
information. When requesting compliance information for this product, always
refer to this series number. The series number should not be confused with the
marketing name or model number of the product.
Network Storage Router N1200 User Guide
175
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance Notices
Federal Communications Commission Notice
Part 15 of the Federal Communications Commission (FCC) Rules and
Regulations has established Radio Frequency (RF) emission limits to provide an
interference-free radio frequency spectrum. Many electronic devices, including
computers, generate RF energy incidental to their intended function and are,
therefore, covered by these rules. These rules place computers and related
peripheral devices into two classes, A and B, depending upon their intended
installation. Class A devices are those that may reasonably be expected to be
installed in a business or commercial environment. Class B devices are those that
may reasonably be expected to be installed in a residential environment (for
example, personal computers). The FCC requires devices in both classes to bear a
label indicating the interference potential of the device as well as additional
operating instructions for the user.
The rating label on the device shows the classification (A or B) of the equipment.
Class B devices have an FCC logo or FCC ID on the label. Class A devices do not
have an FCC logo or FCC ID on the label. After the Class of the device is
determined, refer to the corresponding statement in the following sections.
Class A Equipment
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at
personal expense.
Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
176
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance Notices
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
■
■
■
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit that is different from that to
which the receiver is connected
■
Consult the dealer or an experienced radio or television technician for help
Declaration of Conformity, United States Only
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
For questions regarding your product, contact us by mail or telephone:
■
Hewlett-Packard Computer Corporation
P. O. Box 692000, Mail Stop 530113
Houston, Texas 77269-2000
■
1-800-652-6672 (1-800-OK COMPAQ) (For continuous quality
improvement, calls may be recorded or monitored.)
For questions regarding this FCC declaration, contact us by mail or telephone:
■
Hewlett-Packard Computer Corporation
P. O. Box 692000, Mail Stop 510101
Houston, Texas 77269-2000
■
1-281-514-3333
To identify this product, refer to the part, series, or model number found on the
product.
Modifications
The FCC requires the user to be notified that any changes or modifications made
to this device that are not expressly approved by Hewlett-Packard Computer
Corporation may void the user’s authority to operate the equipment.
Network Storage Router N1200 User Guide
177
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance Notices
Cables
Connections to this device must be made with shielded cables with metallic
RFI/EMI connector hoods in order to maintain compliance with FCC Rules and
Regulations.
Power Cords
The power cord set included in your server meets the requirements for use in the
country where you purchased your server. If you need to use this server in another
country, you should purchase a power cord that is approved for use in that country.
WARNING: This product can ONLY be used with an HP approved power cord
for your specific geographic region. Use of a non-HP approved power cord
may result in: 1) not meeting individual country specific safety requirements;
2) insufficient conductor ampacity that could result in overheating with
potential personal injury and/or property damage; and 3) an unapproved
power cord could fracture resulting in the internal contacts being exposed,
which potentially could subject the user to a shock hazard. HP disclaims all
liability in the event a non-HP approved power cord is used.
The power cord must be rated for the product and for the voltage and current
marked on the product’s electrical ratings label. The voltage and current rating of
the cord should be greater than the voltage and current rating marked on the
product. In addition, the cross sectional area of the wire must be a minimum of
1.00 mm² or 18AWG, and the length of the cord must be between 6 feet (1.8 m)
and 12 feet (3.6 m). If you have questions about the type of power cord to use,
contact your HP authorized service provider.
A power cord should be routed so that it is not likely to be walked on or pinched
by items placed upon it or against it. Particular attention should be paid to the
plug, electrical outlet, and the point where the cord exits from the product.
178
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance Notices
Canadian Notice (Avis Canadien)
Class A Equipment
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement
sur le matériel brouilleur du Canada.
Class B Equipment
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement
sur le matériel brouilleur du Canada.
Network Storage Router N1200 User Guide
179
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance Notices
European Union Notice
Products with the CE Marking comply with both the EMC Directive
(89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the
Commission of the European Community.
Compliance with these directives implies conformity to the following European
Norms (the equivalent international standards are in parenthesis):
■
■
■
■
■
EN55022 (CISPR 22) – Electromagnetic Interference
EN55024 (IEC61000-4-2, 3, 4, 5, 6, 8, 11) – Electromagnetic Immunity
EN61000-3-2 (IEC61000-3-2) – Power Line Harmonics
EN61000-3-3 (IEC61000-3-3) – Power Line Flicker
EN60950 (IEC950) – Product Safety
180
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance Notices
Laser Device
All HP systems equipped with a laser device comply with safety standards,
including International Electrotechnical Commission (IEC) 825. With specific
regard to the laser, the equipment complies with laser product performance
standards set by government agencies as a Class 1 laser product. The product does
not emit hazardous light; the beam is totally enclosed during all modes of
customer operation and maintenance.
Laser Safety Warnings
WARNING: To reduce the risk of exposure to hazardous radiation:
■ Do not try to open the laser device enclosure. There are no user-serviceable
components inside.
■ Do not operate controls, make adjustments, or perform procedures to the
laser device other than those specified herein.
■ Allow only HP authorized service technicians to repair the laser device.
Compliance with CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and
Drug Administration implemented regulations for laser products on August 2,
1976. These regulations apply to laser products manufactured from August 1,
1976. Compliance is mandatory for products marketed in the United States.
Compliance with International Regulations
All HP systems equipped with laser devices comply with appropriate safety
standards including IEC 825.
Laser Product Label
The following label or equivalent is located on the surface of the HP supplied laser
device.
Network Storage Router N1200 User Guide
183
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance Notices
This label indicates that the product is classified
as a CLASS 1 LASER PRODUCT. This label
appears on a laser device installed in your
product.
Laser Information
Table 31: Laser Information
Feature
Description
Semiconductor GaAIAs
Laser type
Wave length
780 nm +/- 35 nm
Divergence angle
Output power
Polarization
53.5 degrees +/- 0.5 degrees
Less than 0.2 mW or 10,869 W m-2 sr-1
Circular 0.25
Numerical aperture
0.45 inches +/- 0.04 inches
184
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrostatic Discharge
E
To avoid damaging the system, be aware of the precautions you need to follow
when setting up the system or handling parts. A discharge of static electricity from
a finger or other conductor may damage system boards or other static-sensitive
devices. This type of damage may reduce the life expectancy of the device.
To prevent electrostatic damage, observe the following precautions:
■
■
■
Avoid hand contact by transporting and storing products in static-safe
containers.
Keep electrostatic-sensitive parts in their containers until they arrive at
static-free workstations.
Place parts on a grounded surface before removing them from their
containers.
■
■
Avoid touching pins, leads, or circuitry.
Always be properly grounded when touching a static-sensitive component or
assembly.
Network Storage Router N1200 User Guide
185
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrostatic Discharge
Grounding Methods
There are several methods for grounding. Use one or more of the following
methods when handling or installing electrostatic-sensitive parts:
■
Use a wrist strap connected by a ground cord to a grounded workstation or
computer chassis. Wrist straps are flexible straps with a minimum of
1 megohm ± 10 percent resistance in the ground cords. To provide proper
ground, wear the strap snug against the skin.
■
Use heel straps, toe straps, or boot straps at standing workstations. Wear the
straps on both feet when standing on conductive floors or dissipating floor
mats.
■
■
Use conductive field service tools.
Use a portable field service kit with a folding static-dissipating work mat.
If you do not have any of the suggested equipment for proper grounding, have a
HP authorized reseller install the part.
Note: For more information on static electricity, or assistance with product installation,
contact your HP authorized reseller.
186
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
C
Active Fabric configuration
Serial/Telnet UI 128
Center for Devices and Radiological Health See
CDRH
Visual Manager UI 50
addressing, defined 169
AL_PA, addressing methods 32
audience 10
clock configuration
Serial/Telnet UI 127
Visual Manager UI 52
configuration settings
backing up 145
authorized reseller, HP 15
auto-assigned addressing
described 173
common 31
restoring 146
troubleshooting 153
configurations, Fibre Channel to SCSI,
illustrated 21
B
controller LUN commands
conventions
backing up the configuration, FTP UI 145
baud rate configuration
Serial/Telnet UI 95
document 11
equipment symbols 12
text symbols 11
Visual Manager UI 46
buffered tape writes
Fibre Channel
conversion process, FCP to SCSI protocol,
illustrated 22
copying trace buffers, FTP UI 147
current map, default
Fibre Channel
Serial/Telnet UI 101
overview of 35
SCSI
Serial/Telnet UI 101
Visual Manager UI 58
SCSI
Serial/Telnet UI 105
Visual Manager UI 60
bus reset on boot
Serial/Telnet UI 105
Visual Manager UI 60
overview of 31
Visual Manager UI 60
D
data movement, server-free 25
Network Storage Router N1200 User Guide
187
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
date configuration
Serial/Telnet UI 127
Visual Manager UI 52
DB-9 pin layout 158
DB-9 serial pin assignments, illustrated 158
default settings, Ethernet 28
default settings, router 28
devices
LED indicators 19
location of 19
event log
clearing
Serial/Telnet UI 139
Visual Manager UI 83
configuration of
Serial/Telnet UI 126
Visual Manager UI 81
viewing
supported 21
troubleshooting 153
DHCP setup
Serial/Telnet UI 139
Visual Manager UI 82
external features, overview 18
Serial/Telnet UI 97
Visual Manager UI 48
discovery mode
F
Fibre Channel
factory settings, resetting
Serial/Telnet UI 129
Serial/Telnet UI 100
overview of 33
Visual Manager UI 53
FCC notices
SCSI
Class A Equipment 176
Class B Equipment 177
classification label 176
Declaration of Conformity 177
FCP to SCSI protocol conversion process,
illustrated 22
Serial/Telnet UI 104
Visual Manager UI 60
document
conventions 11
prerequisites 10
related documentation 10
features of router, external 18
Fibre Channel
E
LED indicators 20
environmental requirements
operating 26
port configuration, overview 32
Fibre Channel connection, troubleshooting 152
Fibre Channel hosts
shipping and storing 26
equipment symbols 12
ESD (electrostatic discharge)
precautions 185
viewing and changing
Serial/Telnet UI 118
Visual Manager UI 66
Fibre Channel maps
preventing 185
adding entries
transporting products 185
Ethernet configuration
default settings 28
Serial/Telnet UI 113
Visual Manager UI 69
clearing entries
Serial/Telnet UI 96
Visual Manager UI 48
Ethernet port
Visual Manager UI 69
creating entries
Serial/Telnet UI 115
188
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager UI 69
deleting entries
Serial/Telnet UI 117
Visual Manager UI 69
editing entries
Serial/Telnet UI 111
Visual Manager 68
filling entries
Serial/Telnet UI 118
Visual Manager UI 69
removing gaps in
Fibre Channel to SCSI configurations, illustrated
21
firmware versions, upgrading
FTP UI 148
Serial/Telnet UI 142
FTP UI
accessing 144
Visual Manager UI 75
configuration, backing up 145
configuration, restoring 146
firmware, upgrading 148
tasks 143
Serial/Telnet UI 117
Visual Manager UI 69
viewing and changing
Serial/Telnet UI 108
Visual Manager UI 68
Fibre Channel port
buffered tape writes
Serial/Telnet UI 101
Visual Manager UI 57
configuration
trace buffers, copying 147
functional overview, of router 21
G
getting help 15
grounding methods 186
Serial/Telnet UI 99
Visual Manager UI 55
default map
Serial/Telnet UI 101
Visual Manager UI 58
discovery mode
Serial/Telnet UI 100
Visual Manager UI 57
override settings
Serial/Telnet UI 102
Visual Manager UI 58
performance mode
Visual Manager UI 58
port mode
H
hard addressing, defined 32
heel straps, using 186
help, obtaining 15
host lists
adding to
Serial/Telnet UI 120
Visual Manager UI 65
deleting from
Serial/Telnet UI 120
editing, Fibre Channel
Serial/Telnet UI 120
Visual Manager UI 66
editing, SCSI
Serial/Telnet UI 120
Visual Manager UI 70
selecting a host for the current map
Serial/Telnet UI 120
Serial/Telnet UI 101
Visual Manager UI 56
port name
Serial/Telnet UI 99
Visual Manager UI 55
Network Storage Router N1200 User Guide
189
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Visual Manager UI 65
hostname
Serial/Telnet UI 97
Visual Manager UI 47
HP
types of 150
link status, Fibre Channel
Serial/Telnet UI 133
Visual Manager UI 55
LUN management
overview 34
authorized reseller 15
storage website 15
technical support 15
M
mapping tasks, Fibre Channel
adding entries
I
I/O configuration
Visual Manager UI 54
indexed addressing
described 174
Serial/Telnet UI 113
Visual Manager 69
changing the name of the host
Visual Manager 66
clearing entries
Visual Manager 69
creating entries
Serial/Telnet UI 115
Visual Manager 69
default current map
Serial/Telnet UI 101
Visual Manager UI 58
deleting entries
indexed maps, defined 34
initiator IDs, SCSI
Serial/Telnet UI 104
Visual Manager UI 59
interfaces
user, listed 29
internal termination, SCSI
Visual Manager UI 60
IP address
Serial/Telnet UI 96
Visual Manager UI 48
IP gateway
Serial/Telnet UI 117
Visual Manager 69
filling entries
Serial/Telnet UI 118
Visual Manager 69
removing gaps in
Serial/Telnet UI 97
Visual Manager UI 48
L
Serial/Telnet UI 117
Visual Manager 69
viewing and changing 106
Visual Manager UI 68
mapping tasks, Fibre Channel and SCSI
adding (creating) a map
Serial/Telnet UI 109
Visual Manager UI 65
adding a host to the host list
Visual Manager UI 65
changing the name of
Serial/Telnet UI 110
laser device
radiation warning 183
LED indicators
defined 150
Ethernet port 19
Fibre Channel 20
power supply 19
SCSI bus 20
190
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
cloning a map
deleting entries
Serial/Telnet UI 118
Visual Manager UI 66
deleting (removing) the current map
Serial/Telnet UI 109
Visual Manager UI 66
deleting a host from the host list
Serial/Telnet UI 120
Visual Manager UI 65
displaying the entire device list
Serial/Telnet UI 123
editing entries
Serial/Telnet UI 117
Visual Manager UI 72
filling entries
Serial/Telnet UI 118
Visual Manager UI 72
removing gaps in
Serial/Telnet UI 117
viewing and changing 106
Visual Manager UI 71
maps
Serial/Telnet UI 111
editing host information
Serial/Telnet UI 121
editing the current map
Serial/Telnet UI 110
editing the host list of the current map
Serial/Telnet UI 118
overview of
auto-assigned, defined 35
indexed, defined 34
overview 33
predefined maps 34
SCC, defined 35
troubleshooting 153
N
Visual Manager UI 64
selecting a host for the current map
Serial/Telnet UI 120
Visual Manager UI 65
selecting the current map
Serial/Telnet UI 107
Visual Manager UI 66
viewing and changing
Serial/Telnet UI 108
Visual Manager UI 65
mapping tasks, SCSI
adding entries
network configuration
Serial/Telnet UI 96
Visual Manager UI 47
O
override settings
Fibre Channel
Serial/Telnet UI 102
Visual Manager UI 58
SCSI
Visual Manager UI 61
Serial/Telnet UI 114
Visual Manager UI 72
clearing entries
Visual Manager UI 72
creating entries
Serial/Telnet UI 116
default current map
P
parts
proper handling 185
storing 185
performance mode, Fibre Channel
Visual Manager UI 58
pin assignments
Serial/Telnet UI 105
Visual Manager UI 60
DB-9 serial 158
Network Storage Router N1200 User Guide
191
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
RJ-45 Ethernet 159
pin layout
DB-9 serial 158
RJ-45 Ethernet 159
port configuration
Serial/Telnet UI 99
port mode, Fibre Channel
Serial/Telnet UI 101
Visual Manager UI 56
port name, Fibre Channel
Serial/Telnet UI 99
Visual Manager UI 55
power requirements, of router 26
power supply
LED indicators 19
prerequisites 10
PRLI data, troubleshooting 155
process, converting Fibre Channel to SCSI,
illustrated 22
process, converting SCSI to Fibre Channel,
illustrated 23
RJ-45 Ethernet pin layout, illustrated 159
router, illustrated 18
S
SCC addressing, described 172
SCC maps, defined 35
SCSI bus
buffered tape writes
Serial/Telnet UI 105
Visual Manager UI 60
bus reset on boot
Serial/Telnet UI 104
Visual Manager UI 60
configuration of
Serial/Telnet UI 103
Visual Manager UI 59
configuration overview 31
configuration, troubleshooting 151
default map
Serial/Telnet UI 105
Visual Manager UI 60
discovery settings
Serial/Telnet UI 104
Visual Manager UI 60
Initiator and Target settings
Serial/Telnet UI 104
Visual Manager UI 59
LED indicators 20
override settings 105
Visual Manager UI 61
termination mode
R
rack stability, warning 14
rebooting
Serial/Telnet UI 141
regulatory compliance notices
Canadian 179
device modifications 177
European Union 180
identification number 175
related documentation 10
report option
Visual Manager UI 60
SCSI devices, troubleshooting 152
SCSI hosts
Visual Manager UI 84
viewing and changing
Serial/Telnet UI 118
Visual Manager UI 70
SCSI maps
requirements of router, physical 26
resetting to factory settings
Serial/Telnet UI 129
Visual Manager UI 53
restoring the configuration, FTP UI 146
RJ-45 Ethernet pin assignments 159
RJ-45 Ethernet pin layout 159
Serial/Telnet UI 114
Visual Manager UI 72
clearing entries
192
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Manager UI 72
creating entries
Serial/Telnet UI 116
Visual Manager UI 72
deleting entries
Serial/Telnet UI 117
Visual Manager UI 72
editing entries
Serial/Telnet UI 111
Visual Manager 71
filling entries
Serial/Telnet UI 118
Visual Manager UI 72
removing gaps in
I/P address 96
I/P gateway 97
MAC address 97
subnet mask 96
event filter setting options, listed 126
event log
clearing 139
viewing 139
event settings, configuration of 126
factory settings, resetting 129
Fibre Channel driver status information,
viewing 136
Visual Manager UI 72
viewing and changing
Serial/Telnet UI 108
Visual Manager UI 71
SCSI to Fibre Channel conversion process,
illustrated 23
security configuration
Serial/Telnet UI 98
Visual Manager UI 51
serial port
Fibre Channel port
buffered tape writes 101
discovery mode 100
override settings 102
port mode 101
port name 99
Fibre Channel status information, viewing
132
main menu, described 92
mapping tasks, Fibre Channel
adding entries 113
location of 19
Serial UI, accessing 90
Serial/Telnet UI
creating entries 115
deleting entries 117
filling entries in 118
removing gaps in 117
Active Fabric configuration 128
baud rate, changing 95
DHCP setup 97
download new firmware option, described
142
mapping tasks, Fibre Channel and SCSI
adding a host to the host list 120
changing the name of the current map 110
cloning the current map 118
creating a new map 109
deleting (removing) the current map 109
deleting a host from the host list 120
displaying the entire device list 123
editing entries of the current map 111
editing host information 121
editing options, listed 110
editing host information on a Fibre Channel
Ethernet configuration 96
DHCP 97
Ethernet mode 97
Network Storage Router N1200 User Guide
193
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
editing the entries of the current map,
options, listed 112
System Utility Menu, described 130
trace and event settings configuration,
described 124
editing the host list of the current map, edit
options, listed 119
trace buffers, saving copies 140
Trace Dump menu, described 139
trace settings, configuring 124
Serial/Telnet UI Active Fabric Configuration
Menu, illustrated 128
Serial/Telnet UI adding a host to the host list -
Serial/Telnet UI adding a host to the host list -
SCSI host, illustrated 120
Serial/Telnet UI Adding an entry to a Fibre
Serial/Telnet UI adding an entry to a SCSI map,
illustrated 114
Serial/Telnet UI Baud Rate Configuration
screen, illustrated 95
Serial/Telnet UI Configuration Menu, illustrated
93
initial access 106
listed 106
screen navigation 107
viewing the current map 108
mapping tasks,SCSI
adding entries 114
creating map entries 116
deleting entries 117
filling entries 118
removing gaps in 117
overview of the UI 29
port configuration 99
reboot option, described 141
Reset and Save Configuration to Factory
defaults option, described 129
Restore Last Saved Configuration option,
described 129
Serial/Telnet UI creating an entry for a SCSI
map, illustrated 116
Serial/Telnet UI creating an map entry for a
Serial/Telnet UI device list generated for a Fibre
Channel port, illustrated 113
Serial/Telnet UI device list generated for a SCSI
port, illustrated 114
Serial/Telnet UI Device Mapping Configuration
Menu, illustrated 106
Serial/Telnet UI Download New Firmware
Menu, illustrated 142
Serial/Telnet UI Edit Map Entries for a Fibre
Channel Map, illustrated 111
Map, illustrated 112
Serial/Telnet UI editing host information on a
SCSI bus, illustrated 122
Save Configuration option, described 129
SCSI attached devices 137
SCSI bus, configuration
bus reset on boot 104
discovery settings 104
Target override settings 105
SCSI resource information 138
SCSI statistics 137
SCSI status information 137
SCSI Status Menu, options, listed 137
server-free backup 128
system statistics information, described 131
System Statistics Menu, options, listed 131
system status information 131
System Utilities Menu, options, listed 130
Serial/Telnet UI event filter settings, illustrated
126
Serial/Telnet UI Event Log Menu, illustrated 139
194
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial/Telnet UI FCP Current Map display,
illustrated 108
Serial/Telnet UI Fibre Channel configuration
screen, illustrated 99
Serial/Telnet UI Fibre Channel Devices Display
page, illustrated 135
Serial/Telnet UI Fibre Channel Driver resource
status screen, illustrated 136
Serial/Telnet UI Fibre Channel link status
screen, illustrated 133
Serial/Telnet UI Fibre Channel Transport
Queues page, illustrated 136
Channel maps, illustrated 119
illustrated 119
Serial/Telnet UI RealTime Clock Configuration
Menu, described 127
Serial/Telnet UI trace settings screen,
continued, illustrated 125
server-free backup
Serial/Telnet UI 128
Visual Manager UI 50
server-free data movement, illustrated 25
soft addressing, defined 32
standby power button
location of 19
statistics information, viewing
Serial/Telnet UI 131
Visual Manager UI 73
subnet mask
Serial/Telnet UI 96
Visual Manager UI 48
symbols in text 11
symbols on equipment 12
Serial/Telnet UI SCSI bus configuration menu,
illustrated 103
Serial/Telnet UI SCSI Current Map display,
T
tables
target override settings
Serial/Telnet UI 105
Visual Manager 61
technical support, HP 15
Telnet UI, accessing 89
text symbols 11
Serial/Telnet UI SCSI Device Display Menu,
illustrated 137
Serial/Telnet UI SCSI Resource Display screen,
illustrated 138
Serial/Telnet UI SCSI Status Menu, illustrated
137
Serial/Telnet UI Select Current Map screen,
illustrated 107
Serial/Telnet UI System Statistics Menu,
Serial/Telnet UI System Status screen, illustrated
131
Serial/Telnet UI System Utilities Menu,
illustrated 130
Serial/Telnet UI Trace Dump menu, illustrated
139
tools
traces
clearing buffers
Serial/Telnet UI 139
Visual Manager UI 80
configuration
Serial/Telnet UI 139
configuration of
Serial/Telnet UI trace settings menu, illustrated
124
Serial/Telnet UI 124
Visual Manager UI 77
Network Storage Router N1200 User Guide
195
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
copying buffers 147
viewing
Visual Manager Fibre Channel Host Name
Visual Manager Fibre Channel Map dialog
box, illustrated 68
Serial/Telnet UI 139
troubleshooting
basic steps, listed 151
Visual Manager FTP Utility screen, illustrated 75
Visual Manager Home page, illustrated 42
Visual Manager Main Menu option bar,
illustrated 44
Visual Manager Network screen, illustrated 47
Visual Manager Ports menu, illustrated 54
Visual Manager Report screen, illustrated 84
illustrated 53
devices, verifying 153
host configuration, verifying 153
mapping, verifying 153
PRLI data, verifying 155
router configuration, verifying 153
SCSI devices, verifying 152
serial port configuration, verifying 154
Visual Manager SCSI bus configuration screen,
illustrated 59
Visual Manager SCSI Device Override screen,
illustrated 61
Visual Manager SCSI Host Name dialog box,
illustrated 70
Visual Manager SCSI Map dialog box,
illustrated 71
U
upgrading the firmware
FTP UI 148
Serial/Telnet UI 142
user configuration
Serial/Telnet UI 98
Visual Manager UI 51
user interfaces, listed 29
utilities configuration
Serial/Telnet UI 130
Visual Manager UI 74
Visual Manager Trace Settings screen,
illustrated 77
V
Visual Manager UI
Visual Manager AL_PA lookup table, illustrated
56
accessing 39
Active Fabric configuration 50
options 50
Visual Manager Clear Current Trace Buffer
screen, illustrated 80
Visual Manager Current traces screen,
illustrated 79
Visual Manager Discovery screen, illustrated 63
Visual Manager Ethernet Configuration dialog
box, illustrated 48
Visual Manager Event Log settings screen,
illustrated 81
baud rate configuration 46
best practices 41
clock configuration 52
discovery 63
Ethernet configuration 48
DHCP 48
Ethernet mode 48
196
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
IP address 48
IP gateway 48
subnet mask 48
selecting a host 65
selecting a map 66
mapping tasks, SCSI
adding entries 72
clearing map entries 72
creating entries 72
deleting entries 72
filling maps 72
removing gaps in 72
viewing and changing 71
network configuration 47
overview of the UI 29
report options 84
event log
clearing 83
configuration 81
display 82
Fibre Channel
buffered tape writes 57
configuration of 55
default map 58
discovery mode 57
hard AL_PA 56
resetting to factory settings 53
SCSI
override settings 58
port mode 56
buffered tape writes 60
bus reset on boot 60
configuration of 59
default map 60
discovery mode 60
initiator IDs 59
port name 55
Fibre Channel hosts, viewing and changing
66
FTP access 75
home page 42
host name, changing 47
I/O configuration 54
main menu 42
mapping tasks 64
overview of 64
adding entries 69
clearing maps 69
creating entries 69
deleting entries 69
filling maps 69
removing gaps in 69
viewing and changing 68
mapping tasks, Fibre Channel and SCSI
adding a new host 65
cloning a map 66
deleting a host 65
deleting a map 66
internal termination 60
override settings 61
settings 59
Target IDs 59
SCSI hosts
serial configuration 46
System Menu 45
traces
clearing buffers 80
configuration 77
displays XE 79
user configuration 51
utilities configuration 74
options 74
Visual Manager Utilities menu, illustrated 74
W
warning
Network Storage Router N1200 User Guide
197
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
rack stability 14
symbols on equipment 12
websites
HP storage 15
wrist straps
using 186
198
Network Storage Router N1200 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
|