HP ProBook 5320m Notebook PC
Maintenance and Service Guide
Document Part Number: 609313-002, Rev. D
February 2012
This guide is a troubleshooting reference used for maintaining and servicing the computer. It provides
comprehensive information on identifying computer features, components, and spare parts; troubleshooting
computer problems; and performing computer disassembly procedures.
Download from Www.Somanuals.com. All Manuals Search And Download.
© Copyright 2012 Hewlett-Packard Development Company, L.P.
AMD Athlon, AMD Sempron, and AMD Turion are trademarks of Advanced Micro Devices, Inc. Bluetooth is a trademark owned by its
proprietor and used by Hewlett-Packard Company under license. Intel and Core are U.S. registered trademarks of Intel Corporation.
Java is a U.S. trademark of Sun Microsystems, Inc. Microsoft, Windows, and Windows Vista are U.S. registered trademarks of
Microsoft Corporation. SD Logo is a trademark of its proprietor.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in
the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Second Edition: February 2011
Document Part Number: 570786-002, Rev. D
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety warning notice
WARNING: To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly
on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface,
such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow
the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International Standard for Safety of
Information Technology Equipment (IEC 60950).
Å
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Identifying hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
Top components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2
Display components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2
Wireless antennas (select models only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3
Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6
Pointing devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7
Front components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
Right-side components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
Left-side components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9
Bottom components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10
Serial number label location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
Computer major components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
Cable Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–6
Display assembly subcomponents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–7
Mass storage devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8
Plastics Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–9
Miscellaneous parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10
Sequential part number listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–11
Preliminary replacement requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Service considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Grounding guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
Component replacement procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Serial number location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Computer feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–6
Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–7
SIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–8
Mass storage device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–9
Bluetooth module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–12
WLAN module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–14
WWAN module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–17
RTC battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–20
Memory module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–21
Maintenance and Service Guide
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–23
Button board and cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–26
Top cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–28
Power button board and cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–31
Bluetooth module cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–32
System board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–33
Fan and heat sink. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–36
Speaker assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–39
USB board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–40
Battery eject arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–41
Display assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–43
Computer Setup in Windows 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
Starting Computer Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
Using Computer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
Computer Setup menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
File menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
Security menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
Diagnostics menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–4
System Configuration menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–5
Computer Setup in Windows Vista . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–7
Starting Computer Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–7
Using Computer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–7
Computer Setup menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–8
File menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–8
Security menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–9
Diagnostics menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–10
System Configuration menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–10
Computer Setup in Windows XP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–13
Starting Computer Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–13
Using Computer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–13
Computer Setup menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–14
File menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–14
Security menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–15
Diagnostics menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–16
System Configuration menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–17
Computer specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–1
13.3-in display specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–2
Hard drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–4
Backup and recovery in Windows 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–1
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–1
Backing up your information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–1
Performing a recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–3
Backup and recovery in Windows Vista . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–5
v
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–5
Backing up your information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–5
Performing a recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–6
Backup and recovery in Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–9
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–9
Backing up your information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–9
Performing a recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–10
Audio-in (microphone). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–1
Audio-out (headphone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–1
External monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–2
RJ-45 (network) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–3
Universal Serial Bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–4
Requirements for all countries and regions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–1
Requirements for specific countries and regions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–2
10Recycling
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–1
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–1
Maintenance and Service Guide
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Product description
Category
Description
Product name
Processors
HP ProBook 5320m Notebook PC
■ Intel® Dual Core i5-45M 2.40-GHz processor (Turbo up to 2.53 GHz), 3-M L3 cache,
4 threads (35W)
■ Intel Dual Core i3-370M 2.40-GHz processor, 3-M L3 cache, 4 threads (35W)
■ Intel Dual Core i3-350M 2.26-GHz processor, 3-M L3 cache, 4 threads (35W)
■ Intel U3400 1.06-GHz processor
Chipset
Graphics
Panel
Intel HM57
Mobile Intel Graphics Media Accelerator HD unified memory architecture (UMA)
■ 13.3-in, high-definition (HD, 1366 × 768), AntiGlare, LED display assembly
■ 13.3-in, HD (1366 × 768), BrightView, LED display assembly
■ Supports privacy filter
Memory
One customer-accessible/upgradable memory module slot
Supports the following DDR3 configurations at 1333 MHz in all countries and regions:
■ 4096-MB total system memory (4096 × 1)
■ 2048-MB total system memory (2048 × 1)
■ 1024-MB total system memory (1024 × 1) (not available on Microsoft 64-bit operating
systems)
Hard drives
Supports 9.50-mm, 6.35-cm (2.50-in) hard drives
Customer-accessible
Supports the following hard drives:
■ 500-GB, 7200 rpm
■ 320-GB, 7200 rpm
■ 250-GB, 7200 rpm
Supports the following solid-state drives only with computer models running Windows 7
operating system, 2 GB or 4 GB:
■ 128-GB
■ 80-GB
Microphone
Audio
Integrated dual-array digital microphone
High-definition audio
Stereo speakers (2)
Webcam
Integrated 2-megapixel camera
(Continued)
Maintenance and Service Guide
1–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product description
Category
Ethernet
Description
Realtek RTL811DL-VR10/100/1000 network interface card (NIC)
NIC Power Down technology
S3/S4/S5 wake on LAN (AC mode only)
Ethernet cable not included
Wireless
Integrated wireless local-area network (WLAN) options via half MiniCard:
■ Broadcom 802.11 b/g/n WLAN module
■ Broadcom 43224 802.11a/b/g/n 2x2 WiFi adapter
Supports no-WLAN option
2 WLAN antennas built into the display assembly
Integrated wireless wide-area network (WWAN) options via Mini PCI module:
UNDP High-speed packet access (HSPA), evolution-data optimized (EV-DO) WWAN
module
WWAN security provided by subscriber identity module (SIM), user-accessible behind
battery
2 WWAN antennas (worldwide, 5-band) built into the display assembly
Supports no-WWAN option
Supports WWAN aftermarket option
Integrated wireless personal-area network (WPAN) options via Bluetooth® module
Supports no-WPAN option
External media cards
SD Card Reader supporting the following optional digital card formats:
■ MultiMediaCard (MMC)
■ Secure Digital (SD) Memory Card
Ports
Combo headphone microphone (supports audio-in/stereo microphone and
audio-out/stereo headphone)
Multi-pin AC power
RJ-45 (Ethernet, includes link and activity lights)
USB v. 2.0 (3, one powered)
DisplayPort (Dsub 15-pin) supporting 1600 × 1200 external resolution at 75 GHz
Keyboard/pointing devices
Power requirements
Keyboard with Dura-Keys
TouchPad with TouchPad buttons
Supports 2-way and 4-way scroll with legend
Supports gestures (enabled by default)
Taps enabled by default
65-W AC HP Smart Adapter
65-W AC HP Slim Adapter (for use only in Japan)
Supports multi-pin AC connector and 3-wire plug (with ground pin)
Supports 6-cell, 2.80-Ah battery
Supports 4-cell, 2.80-Ah battery
Supports HP Fast Charge technology only on 6-cell battery
Security
Security cable slot
HP fingerprint sensor (optional)
Full-volume encryption
Intel AT support
HP face recognition
Privacy filter
Preboot authentication (password and smart card)
(Continued)
1–2
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Product description
Category
Description
Operating system
Preinstalled:
■ Windows 7 Home Premium 32 (French Canada and Japan)
■ Windows 7 Home Premium 64 (French Canada and Japan)
■ Windows 7 Professional (Pro) 32 (French Canada and Japan)
■ Windows 7 Professional 64 (French Canada and Japan)
■ Windows 7 Professional (with Windows XP Pro images) ( French Canada and Japan)
■ Windows Vista Home Basic (fFrench Canada and Japan)
■ FreeDOS (all countries and regions)
■ Red Flag Linux (the People’s Republic of China only)
■ SuSe Linux (all countries and regions)
Preinstalled with Microsoft® Office:
■ Windows 7 Home Basic 32 with Office 2007 Ready (limited Europe, MIddle East, Asia
(EMEA) region)
■ Windows 7 Home Basic 32 with Office 2010 Ready (limited Asia Pacific, Japan (APJ)
region)
■ Windows 7 Home Premium 32 with Office 2007 Ready (EMEA region)
■ Windows 7 Home Premium 32 with Office 2010 Ready (APJ region)
■ Windows 7 Home Premium 32 with Home and Business 2010 (Japan)
■ Windows 7 Home Premium 32 Personal 2010 (Japan)
■ Windows 7 Home Premium 32 Professional 2010(Japan)
■ Windows 7 Home Premium 64 with Office 2007 Ready (EMEA region)
■ Windows 7 Home Premium 64 with Office 2010 Ready (APJ region)
■ Windows 7 Home Premium 64 with Home and Business 2010 (Japan)
■ Windows 7 Home Premium 64 Personal 2010 (Japan)
■ Windows 7 Home Premium 64 Professional 2010 (Japan)
■ Windows 7 Pro 32 with Office 2007 Ready (EMEA region)
■ Windows 7 Pro 32 with Office 2010 Ready (APJ region)
■ Windows 7 Pro 32 with Home and Business 2010 (Japan)
■ Windows 7 Pro 32 Personal 2010 (Japan)
■ Windows 7 Pro 32 Pro 2010 (Japan)
■ Windows 7 Pro 64 with Office 2007 Ready (EMEA region)
■ Windows 7 Pro 64 with Office 2010 Ready (APJ region)
■ Windows 7 Pro 64 with Home and Business 2010 (Japan)
■ Windows 7 Pro 64 Personal 2010 (Japan)
■ Windows 7 Pro 64 Pro 2010 (Japan)
■ Windows 7 Pro 32 (with Windows XP Pro images) with Office 2007 Ready
■ Windows 7 Pro 32 (with Windows XP Pro images) with Office Personal (Japan)
■ Windows 7 Pro 32 (with Windows XP Pro images) with Office Personal with
PowerPoint (Japan)
■ Windows 7 Pro 32 (with Windows XP Pro images) with Office Pro (Japan)
■ Windows Vista Home Basic with Office 2007 Ready (Europe, Middle East, Asia
region)
■ Windows Vista Home Basic with Office 2010 Ready (Asia Pacific and Japan region)
(Continued)
Maintenance and Service Guide
1–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Product description
Category
Description
Restore media:
Available with Windows 7 Pro 32, Windows 7 Pro 64, Windows 7 Pro with Windows
XP images:
■ Windows XP Pro
■ Windows 7 Pro 32
■ Windows 7 Pro 64
■ DRDVD Windows XP Pro
Available with Windows 7 Home Premium 32, Windows 7 Home Premium 64
■ Windows 7 Home Premium 32
■ Windows 7 Home Premium 64
Available with Windows Vista Home Basic
■ Windows Vista Home Basic
■ DRDVD Windows Vista
■ DRDVD Windows 7 (Windows 7)
■ Windows 7 Home Basic 32 (Windows 7 Basic 32)
Certified:
■ Microsoft WHQL
Web-only support:
■ Windows Vista Enterprise 64 and 32
■ Windows Vista Business
Serviceability
End-user replaceable parts:
AC adapter
Battery (system)
Hard drive
Memory module
SIM
Solid-state drive
WLAN module
WWAN module
1–4
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
2
External component identification
Identifying hardware
Components included with the computer may vary by region and model. The illustrations in this chapter identify
the standard features on most computer models.
To see a list of hardware installed in the computer, follow these steps:
In Windows 7:
»
Select Start > Control Panel > System and Security > Device Manager.
Windows includes the User Account Control feature to improve the security of your computer. You may be
prompted for your permission or password for tasks such as installing software, running utilities, or changing
Windows settings. Refer to Help and Support for more information.
✎
✎
In Windows Vista:
1. Select Start > Computer > System Properties.
2. In the left pane, click Device Manager.
Windows includes the User Account Control feature to improve the security of your computer. You may be
prompted for your permission or password for tasks such as installing software, running utilities, or changing
Windows settings. Refer to Help and Support for more information.
In Windows XP:
1. Select Start > My Computer.
2. In the left pane of the System Tasks window, select View system information.
3. Select Hardware tab > Device Manager.
You can also add hardware or modify device configurations using Device Manager.
Maintenance and Service Guide
2–1
Download from Www.Somanuals.com. All Manuals Search And Download.
External component identification
Top components
Display components
Your computer may look slightly different from the illustration in this section.
✎
Item Component
Description
(1)
Internal display switch
Turns off the display and initiates Sleep (Windows 7 and Windows Vista) or
Standby (Windows XP) if the display is closed while the power is on.
(2)
Internal microphones (2)
Webcam
Record sound.
If there is a microphone icon next to each microphone opening, your
computer has internal microphones.
✎
(3)
Records video and captures still photographs.
2–2
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
External component identification
Wireless antennas (select models only)
Item Component
Description
(1)
WWAN antennas (2)* (select
models only)
Send and receive wireless signals to communicate with wireless wide-area
networks (WWANs).
(2)
WLAN antennas (2)* (select
models only)
Send and receive wireless signals to communicate with wireless local area
networks (WLANs).
*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around
the antennas free from obstructions.
To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies to
your country or region. These notices are located in Help and Support.
Maintenance and Service Guide
2–3
Download from Www.Somanuals.com. All Manuals Search And Download.
External component identification
Buttons
Item Component
Description
(1)
Power button
■ When the computer is off, press the button to turn on the computer.
■ When the computer is on, press the button to shut down the computer.
Although you can shut down the computer with the power button, the
✎
recommended procedure is to use the Windows Shut Down command.
■ When the computer is in the Sleep state (Windows 7 and Windows Vista)
or Standby (Windows XP), press the button briefly to exit the Sleep state
(Windows 7 and Windows Vista) or Standby (Windows XP).
■ When the computer is in Hibernation, press the button briefly to exit
Hibernation.
If the computer has stopped responding and Windows shutdown procedures
are ineffective, press and hold the power button for at least 5 seconds to turn
off the computer.
To learn more about your power settings:
■ In Windows 7: Select Start > Control Panel > System and Security >
Power Options.
■ In Windows Vista: Select Start > Control Panel > System and
Maintenance > Power Options.
■ In Windows XP: Select Start > Control Panel > Performance and
Maintenance > Power Options.
(2)
(3)
Wireless button
Turns the wireless feature on or off but does not establish a
wireless connection.
QuickLook button
Allows you to save calendar, contact, inbox, and task information from
Microsoft Outlook to the hard drive of your computer. When the computer is
off or in Hibernation, you can press the QuickLook button to view this
information without waiting for the operating system to restart.
(4)
QuickWeb button
Opens the Web browser.
2–4
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
External component identification
Keys
Your computer may look slightly different from the illustration in this section.
✎
Item Component
Description
(1)
(2)
esc key
fn key
Displays system information when pressed in combination with the fn key.
Executes frequently used system functions when pressed in combination with
a function key or the esc key.
(3)
(4)
(5)
(6)
Windows logo key
Displays the Windows Start menu.
Windows applications key
Embedded numeric keypad keys
Function keys
Displays a shortcut menu for items beneath the pointer.
Can be used like the keys on an external numeric keypad.
Execute frequently used system functions when pressed in combination with
the fn key.
Maintenance and Service Guide
2–5
Download from Www.Somanuals.com. All Manuals Search And Download.
External component identification
Lights
Your computer may look slightly different from the illustration in this section.
✎
Item Component
Description
(1)
Power light
■ On: The computer is on.
■ Blinking: The computer is in the Sleep state (Windows 7 and
Windows Vista) or Standby (Windows XP).
■ Off: The computer is off or in Hibernation.
(2)
(3)
Caps lock light
Wireless light
On: Caps lock is on.
■ Blue: An integrated wireless device, such as a WLAN device, the
HP Mobile Broadband Module (select models only), and/or a Bluetooth
device, is on.
■ Amber: All wireless devices are off.
(4)
(5)
QuickLook light
QuickWeb light
Turns on briefly when the QuickLook button is pressed.
Turns on briefly when the QuickWeb button is pressed.
2–6
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
External component identification
Pointing devices
Item Component
Description
(1)
(2)
(3)
(4)
TouchPad*
Moves the pointer and selects or activates items on the screen.
Functions like the left button on an external mouse.
Scrolls up or down.
Left TouchPad button*
TouchPad scroll zone
Right TouchPad button*
Functions like the right button on an external mouse.
*This table describes factory settings. To view or change pointing device preferences:
■ In Windows 7: Select Start > Devices and Printers. Then, right-click the device representing your computer, and select
Mouse settings.
■ In Windows Vista: Select Start > Control Panel > Hardware and Sound > Mouse.
■ In Windows XP: Select Start > Control Panel > Printers and Other Hardware > Mouse.
Maintenance and Service Guide
2–7
Download from Www.Somanuals.com. All Manuals Search And Download.
External component identification
Front components
Item Component
Description
(1)
(2)
(3)
Drive light
Speakers (2)
Vent
Blinking: The hard drive or an external optical drive is being accessed.
Produce sound.
Enables airflow to cool internal components.
The computer fan starts up automatically to cool internal components
✎
and prevent overheating. It is normal for the internal fan to cycle on and
off during routine operation.
Right-side components
Item Component
Description
(1)
SD Card Reader
Supports the following optional digital card formats:
■ MultiMediaCard (MMC)
■ Secure Digital (SD) Memory Card
(2)
Combo headphone microphone jack
Produces sound when connected to optional powered stereo speakers,
headphones, ear buds, a headset, or television audio. Also connects an
optional headset microphone.
When a device is connected to the headphone jack, the computer
speakers are disabled.
✎
(3)
(4)
USB ports (2)
Connect optional USB devices.
Security cable slot
Attaches an optional security cable to the computer.
The security cable is designed to act as a deterrent, but it may not
prevent the computer from being mishandled or stolen.
✎
2–8
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
External component identification
Left-side components
Item Component
Description
(1)
Battery light
■ Amber: A battery is charging.
■ Blue: A battery is close to full charge capacity.
■ Blinking amber: A battery that is the only available power source has
reached a low battery level. When the battery reaches a critical battery
level, the battery light begins blinking rapidly.
■ Off: If the computer is plugged into an external power source, the light turns
off when all batteries in the computer are fully charged. If the computer is
not plugged into an external power source, the light stays off until the
battery reaches a low battery level.
(2)
(3)
Power connector
Vent
Connects an AC adapter.
Enables airflow to cool internal components.
The computer fan starts up automatically to cool internal components
✎
and prevent overheating. It is normal for the internal fan to cycle on and
off during routine operation.
(4)
Powered USB port
Provides power to a USB device, such as an optional external MultiBay or an
optional external optical drive, if used with a powered USB cable.
(5)
(6)
DisplayPort
Connects an external VGA monitor or projector.
Connects a network cable.
RJ-45 (network) jack
Maintenance and Service Guide
2–9
Download from Www.Somanuals.com. All Manuals Search And Download.
External component identification
Bottom components
Item Component
Description
(1)
(2)
Battery bay
Holds the battery.
SIM slot (select models only)
Contains a wireless subscriber identity module (SIM). The SIM slot is located
inside the battery bay.
(3)
Vents (6)
Enable airflow to cool internal components.
The computer fan starts up automatically to cool internal components
✎
and prevent overheating. It is normal for the internal fan to cycle on and
off during routine operation.
(4)
(5)
Hard drive bay
Holds the hard drive and contains the memory module slot.
Releases the battery from the battery bay.
Battery release latch
2–10
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Illustrated parts catalog
Serial number label location
When ordering parts or requesting information, the serial number label, located on the bottom of the computer,
provides important information that you may need when contacting technical support.
Serial number label location, format, and color vary on select models.
✎
(1)
(2)
(3)
Product name
Serial number
Product number
(4)
(5)
Warranty period
Model description (select models only)
Maintenance and Service Guide
3–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrated parts catalog
Item
(1)
Description
Spare part number
Display assembly (includes 2 WLAN antenna transceivers and cables, 2 WWAN antenna transceivers and cables,
webcam, nameplate, and logo):
13.3-in, high-definition (HD), LED, AntiGlare display assembly
13.3-in, HD, LED, BrightView display assembly
618827-001
618828-001
part information.
✎
(2)
Keyboard (includes keyboard cable):
For use in Belgium
618843-A41
618843-261
618843-A81
618843-081
618843-051
618843-DW1
618843-121
618843-041
618843-DJ1
618843-211
618843-DD1
618843-BB1
618843-061
618843-291
618843-B31
618843-091
618843-131
618843-251
618843-171
618843-BA1
618843-AD1
618843-071
618843-B71
618843-BG1
618843-AB1
618843-281
618843-141
618843-031
618843-001
For use in Bulgaria
For use in the Czech Republic and Slovakia
For use in Denmark
For use in France
For use in France and Arabia
For use in French Canada
For use in Germany
For use in Greece
For use in Hungary
For use in Iceland
For use in Israel
For use in Italy
For use in Japan
For use in the Netherlands
For use in Norway
For use in Portugal
For use in Russia
For use in Saudi Arabia
For use in Slovenia
For use in South Korea
For use in Spain
For use in Sweden and Finland
For use in Switzerland
For use in Taiwan
For use in Thailand
For use in Turkey
For use in the United Kingdom
For use in the United States
(Continued)
Maintenance and Service Guide
3–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrated parts catalog
Item
(3)
Description
Spare part number
Top cover with fingerprint reader (includes TouchPad button board and cable, and
TouchPad board and cable)
618840-001
Top cover with fingerprint reader (includes TouchPad button board and cable, and
618841-001
TouchPad board and cable)
(4)
Power button board with FFC (includes cable)
Cable Kit, includes:
618816-001
618826-001
(5a)
(5b)
(5c)
Power button board cable
Bluetooth module cable
USB board cable
✎
(6)
(7)
Button board with FFC (includes cable)
618815-001
System board (includes processor and replacement thermal material):
System board with Intel® Dual Core i5-45M 2.40-GHz processor (Turbo up to 2.53 GHz),
3-M L3 cache, 4 threads (35W)
618821-001
618822-001
618819-001
618820-001
618817-001
618818-001
System board with Intel® Dual Core i5-45M 2.40-GHz processor (Turbo up to 2.53 GHz),
3-M L3 cache, 4 threads (35W), for use in China and Russia
System board with Intel Dual Core i3-370M 2.40-GHz processor, 3-M L3 cache, 4 threads
(35W)
System board with Intel Dual Core i3-370M 2.40-GHz processor, 3-M L3 cache, 4 threads
(35W), for use in China and Russia
System board with Intel Dual Core i3-350M 2.26-GHz processor, 3-M L3 cache, 4 threads
(35W)
System board with Intel Dual Core i3-350M 2.26-GHz processor, 3-M L3 cache, 4 threads
(35W), for use in China and Russia
System board with Intel U3400 1.06-GHz processor
System board with Intel U3400 1.06-GHz processor, for use in China and Russia
USB board (includes cable)
618823-001
618824-001
618825-001
618835-001
(8)
Plastics Kit, includes:
(9a)
(9b)
SD Card Reader slot bezel
Accessory cover (includes 2 captive screws)
✎
(10)
(11)
(12)
Speaker assembly (includes cable)
618839-001
618830-001
618813-001
581090-001
581101-001
580956-001
594796-001
537921-001
Fan/Heat sink (includes replacement thermal material)
Base enclosure (includes 6 rubber feet)
Latch Kit (not illustrated, includes battery eject arm, latch, and spring)
Rubber Feet Kit (not illustrated, includes 6 rubber feet and 2 display bezel screw covers)
4-cell, 41-WHr, 2.8-Ah battery
(13)
(14)
6-cell, 62-WHr, 2.8-Ah battery (supports HP Fast Charge Technology)
Bluetooth module
The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is
included in the Cable Kit, spare part number 618826-001.
✎
(Continued)
3–4
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrated parts catalog
Item
(15)
(16)
Description
Spare part number
RTC battery (includes double-sided tape)
Memory module:
481089-001
4096-MB (1333-MHz, DDR3, PC3-10600 Shared)
2048-MB (1066-MHz, DDR3, PC3-10600)
599092-001
581096-001
598859-001
1024-MB (1066-MHz, DDR3, PC3-10600 Shared) (not available on Microsoft 64-bit
operating systems)
(17)
(18)
HSPA EV-DO WWAN module (does not support Linux operating system; available in all
countries and regions, except China)
531993-001
WLAN module:
802.11 a/b/g/n WLAN module:
■ Broadcom 43224 802.11 a/g/n WLAN module for use in Antigua and Barbuda, Barbados, 582564-001
Belize, Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago,
the U.S. Virgin Islands, and the United States
■ Broadcom 43224 802.11 a/g/n WLAN module for use in Afghanistan, Albania, Algeria,
Andorra, Angola, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan,
the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin,
Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil,
582564-002
the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia,
Cameroon, Cape Verde, the Central African Republic, Chad, Chile, Colombia, Comoros,
the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti,
Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador,
Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,
Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe,
Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary,
Iceland, India, Indonesia, Ireland, Italy, the Ivory Coast, Jamaica, Japan, Jordan,
Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania,
Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua,
Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay,
the People’s Republic of China, Peru, the Philippines, Poland, Portugal, Qatar,
the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa,
South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga,
Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates,
the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire,
Zambia, and Zimbabwe
(18)
(19)
802.11 b/g/n WLAN module:
■ Broadcom 4312G 802.11 b/g/n WLAN module for use in Canada, the Cayman Islands,
593836-001
Guam, Puerto Rico, the United States, and the U.S. Virgin Islands
Mass storage device (includes bracket):
Hard drive:
■ 500-GB, 7200 rpm
■ 320-GB, 7200 rpm
■ 250-GB, 7200 rpm
618829-001
581084-001
581083-001
Solid-state drive (only with computer models running Windows 7 operating system, 2 GB or 4 GB):
■ 128-GB
■ 80-GB
581085-001
581086-001
Maintenance and Service Guide
3–5
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrated parts catalog
Display assembly subcomponents
Item Description
Spare part number
618832-001
(1)
(2)
(3)
Display bezel
Webcam module
618842-001
Display Hinge Kit (includes left and right hinges)
Display Cable Kit, includes:
581094-001
618833-001
(4a)
(4b)
(4c)
(4d)
(5)
Display panel cable and webcam cable
Microphones and cables
WWAN antenna transceivers and cables
WLAN antenna transceivers and cables
Display enclosure (includes microphones and cables, WLAN antenna transceivers and
cables, and WWAN antenna transceivers and cables)
618831-001
Maintenance and Service Guide
3–7
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrated parts catalog
Mass storage devices
Item Description
Spare part number
(1)
Hard drive (includes bracket):
500-GB, 7200 rpm
320-GB, 7200 rpm
250-GB, 7200 rpm
618829-001
581084-001
581083-001
(2)
Solid-state drive (includes bracket), only with computer models running Windows 7 operating system, either 2 GB or
4 GB:
128-GB
80-GB
581085-001
581086-001
3–8
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrated parts catalog
Miscellaneous parts
Description
Spare part number
613161-001
65-W PFC RC/V HP Smart Adapter
65-W PFC RC/V HP Slim Adapter (for use only in Japan)
Power cord:
613152-001
For use in Australia
490371-011
490371-081
490371-021
490371-D61
490371-BB1
490371-061
490371-291
490371-AA1
490371-AR1
490371-AD1
490371-111
490371-AB1
490371-031
490371-001
618838-001
For use in Denmark
For use in Europe, the Middle East, and Africa
For use in India
For use in Israel
For use in Italy
For use in Japan
For use in the People’s Republic of China
For use in South Africa
For use in South Korea
For use in Switzerland
For use in Taiwan
For use in the United Kingdom and Singapore
For use in the United States
Screw Kit:
Phillips PM3.0×4.0 screw
Phillips PM2.5×11.0 captive screw
Phillips PM2.5×6.0 captive screw
Phillips PM2.5×5.0 screw
Phillips PM2.5×4.0 broadhead screw
Phillips PM2.5×4.0 screw
Phillips PM2.5×2.0 broadhead screw
Slotted Torx T8M2.5×7.0 screw
Torx T8M2.5×9.0 screw
Torx T8M2.0×7.0 captive screw
Torx T8M2.5×6.0 screw
Torx T8M2.5×5.0 screw
Torx T8M2.5×4.0 screw
3–10
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrated parts catalog
Sequential part number listing
Spare part number
481089-001
490371-001
490371-011
490371-021
490371-031
490371-061
490371-081
490371-111
490371-291
490371-AA1
490371-AB1
490371-AD1
490371-AR1
490371-BB1
490371-D61
531993-001
Description
RTC battery (includes double-sided tape)
Power cord for use in the United States
Power cord for use in Australia
Power cord for use in Europe, the Middle East, and Africa
Power cord for use in the United Kingdom and Singapore
Power cord for use in Italy
Power cord for use in Denmark
Power cord for use in Switzerland
Power cord for use in Japan
Power cord for use in the People’s Republic of China
Power cord for use in Taiwan
Power cord for use in South Korea
Power cord for use in South Africa
Power cord for use in Israel
Power cord for use in India
HSPA EV-DO WWAN module (does not support Linux operating system; available in all countries and
regions, except China)
537921-001
Bluetooth module
The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth
module cable is included in the Cable Kit, spare part number 618826-001.
✎
580956-001
581094-001
581096-001
581083-001
581084-001
581085-001
4-cell, 41-WHr, 2.8-Ah battery
Display Hinge Kit (includes left and right hinges)
2048-MB memory module (1333-MHz, DDR3)
250-GB, 7200-rpm hard drive (includes bracket)
320-GB, 7200-rpm hard drive (includes bracket)
128-GB solid-state drive (includes bracket), only with computer models running Windows 7 operating
system, either 2 GB or 4 GB
581086-001
80-GB solid-state drive (includes bracket), only with computer models running Windows 7 operating
system, either 2 GB or 4 GB
581090-001
581101-001
582564-001
Latch Kit (includes battery eject arm, latch, and spring)
Rubber Feet Kit (includes 6 rubber feet and 2 display bezel screw covers)
Broadcom 43224 802.11 a/b/g/n WLAN module for use in Antigua and Barbuda, Barbados, Belize,
Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands,
and the United States
(Continued)
Maintenance and Service Guide
3–11
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrated parts catalog
Spare part number
582564-002
Description
Broadcom 43224 802.11 a/b/g/n WLAN module for use in Afghanistan, Albania, Algeria, Andorra,
Angola, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso,
Burundi, Cambodia, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, Colombia,
Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti,
Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea,
Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany,
Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana,
Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Italy, the Ivory Coast,
Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal,
the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman,
Pakistan, Palau, Panama, Papua New Guinea, Paraguay, the People’s Republic of China, Peru,
the Philippines, Poland, Portugal, Qatar, the Republic of Moldova, Romania, Russia, Rwanda,
Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles,
Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa,
South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent, Suriname, Swaziland,
Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
593836-001
Broadcom 4312G 802.11 b/g/n WLAN module for use in Canada, the Cayman Islands, Guam,
Puerto Rico, the United States, and the U.S. Virgin Islands
594796-001
598859-001
6-cell, 62-WHr, 2.8-Ah battery (supports HP Fast Charge technology)
1024-MB memory module (1333-MHz, DDR3, PC3-10600 Shared) (not available on Microsoft 64-bit
operating systems)
599092-001
613152-001
613161-001
618813-001
618815-001
618816-001
618817-001
618818-001
4096-MB memory module (1333-MHz, DDR3, PC3-10600 Shared)
65-W PFC RC/V HP Slim Adapter
65-W PFC RC/V HP Smart Adapter (for use only in Japan)
Base enclosure (includes 6 rubber feet)
Button board with FFC (includes cable)
Power button board with FFC (includes cable)
System board with Intel Dual Core i3-350M 2.26-GHz processor, 3-M L3 cache, 4 threads (35W)
System board with Intel Dual Core i3-350M 2.26-GHz processor, 3-M L3 cache, 4 threads (35W), for
use in China and Russia
618819-001
618820-001
System board with Intel Dual Core i3-370M 2.40-GHz processor, 3-M L3 cache, 4 threads (35W)
System board with Intel Dual Core i3-370M 2.40-GHz processor, 3-M L3 cache, 4 threads (35W), for
use in China and Russia
618821-001
618822-001
System board with Intel® Dual Core i5-45M 2.40-GHz processor (Turbo up to 2.53 GHz), 3-M L3
cache, 4 threads (35W)
System board with Intel® Dual Core i5-45M 2.40-GHz processor (Turbo up to 2.53 GHz), 3-M L3
cache, 4 threads (35W), for use in China and Russia
618823-001
618824-001
618825-001
618826-001
System board with Intel U3400 1.06-GHz processor
System board with Intel U3400 1.06-GHz processor, for use in China and Russia
USB board (includes cable)
Cable Kit
✎
(Continued)
3–12
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrated parts catalog
Spare part number
Description
618827-001
13.3-in, HD, LED, AntiGlare display assembly (includes 2 WLAN antenna transceivers and cables,
2 WWAN antenna transceivers and cables, webcam, nameplate, and logo)
618828-001
13.3-in, HD, LED, BrightView display assembly (includes 2 WLAN antenna transceivers and cables,
2 WWAN antenna transceivers and cables, webcam, nameplate, and logo)
618829-001
618830-001
618831-001
500-GB, 7200-rpm hard drive (includes bracket)
Fan/Heat sink (includes replacement thermal material)
Display enclosure (includes microphones and cables, WLAN antenna transceivers and cables, and
WWAN antenna transceivers and cables)
618832-001
618833-001
Display bezel
Display Cable Kit (includes display panel cable and webcam cable, microphones and cables, WLAN
antenna transceivers and cables, and WWAN antenna transceivers and cables)
618835-001
Plastics Kit
✎
618838-001
618839-001
618840-001
Screw Kit
Speaker assembly (includes cable)
Top cover with fingerprint reader (includes TouchPad button board and cable, and TouchPad board
and cable)
618841-001
Top cover with no fingerprint reader (includes TouchPad button board and cable, and TouchPad board
and cable)
618842-001
618843-001
618843-031
618843-041
618843-051
618843-061
618843-071
618843-081
618843-091
618843-121
618843-131
618843-141
618843-171
618843-211
618843-251
618843-261
618843-281
618843-291
618843-A41
618843-A81
618843-AB1
Webcam module
Keyboard for use in the United States (includes keyboard cable)
Keyboard for use in the United Kingdom (includes keyboard cable)
Keyboard for use in Germany (includes keyboard cable)
Keyboard for use in France (includes keyboard cable)
Keyboard for use in Italy (includes keyboard cable)
Keyboard for use in Spain (includes keyboard cable)
Keyboard for use in Denmark (includes keyboard cable)
Keyboard for use in Norway (includes keyboard cable)
Keyboard for use in French Canada (includes keyboard cable)
Keyboard for use in Portugal (includes keyboard cable)
Keyboard for use in Turkey (includes keyboard cable)
Keyboard for use in Saudi Arabia (includes keyboard cable)
Keyboard for use in Hungary (includes keyboard cable)
Keyboard for use in Russia (includes keyboard cable)
Keyboard for use in Bulgaria (includes keyboard cable)
Keyboard for use in Thailand (includes keyboard cable)
Keyboard for use in Japan (includes keyboard cable)
Keyboard for use in Belgium (includes keyboard cable)
Keyboard for use in the Czech Republic and Slovakia(includes keyboard cable)
Keyboard for use in Taiwan (includes keyboard cable)
(Continued)
Maintenance and Service Guide
3–13
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrated parts catalog
Spare part number
Description
618843-AD1
618843-B31
618843-B71
618843-BA1
618843-BB1
618843-BG1
618843-DD1
618843-DJ1
618843_DW1
Keyboard for use in South Korea (includes keyboard cable)
Keyboard for use in the Netherlands (includes keyboard cable)
Keyboard for use in Sweden and Finland (includes keyboard cable)
Keyboard for use in Slovenia (includes keyboard cable)
Keyboard for use in Israel (includes keyboard cable)
Keyboard for use in Switzerland (includes keyboard cable)
Keyboard for use in Iceland (includes keyboard cable)
Keyboard for use in Greece (includes keyboard cable)
Keyboard for use in France and Arabia (includes keyboard cable)
3–14
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Removal and replacement procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
■
■
■
■
Flat-bladed screwdriver
Phillips P0 screwdriver
Phillips P1 screwdriver
Torx T8 screwdriver
Service considerations
The following sections include some of the considerations that you must keep in mind during disassembly and
assembly procedures.
As you remove each subassembly from the computer, place the subassembly (and all accompanying screws)
away from the work area to prevent damage.
✎
Plastic parts
CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the
plastic parts. Apply pressure only at the points designated in the maintenance instructions.
Ä
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly
process. Improper cable placement can damage the computer.
Ä
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the
cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid
bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be caught or
snagged by parts being removed or replaced. Handle flex cables with extreme care; these cables tear easily.
Maintenance and Service Guide
4–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the computer,
Ä
damage to a drive, or loss of information, observe these precautions:
■ Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off
or in Hibernation, turn the computer on, and then shut it down through the operating system.
■ Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid
touching the connector.
■ Handle drives on surfaces covered with at least one inch of shock-proof foam.
■ Avoid dropping drives from any height onto any surface.
■ After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
■ Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
■ Avoid exposing a drive to temperature extremes or liquids.
■ If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective packaging
and label the package “FRAGILE.”
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the
degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD
contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a normal cycle.
Or, the device may function normally for a while, and then degrade in the internal layers, reducing its life
expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal components, observe
Ä
these precautions:
■ Keep components in their electrostatic-safe containers until you are ready to install them.
■ Use nonmagnetic tools.
■ Before touching an electronic component, discharge static electricity by using the guidelines described in
this section.
■ Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
■ If you remove a component, place it in an electrostatic-safe container.
4–2
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
The following table shows how humidity affects the electrostatic voltage levels generated by different activities.
ÄCAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
10%
40%
55%
Walking across carpet
35,000 V
12,000 V
6,000 V
2,000 V
11,500 V
14,500 V
26,500 V
21,000 V
15,000 V
5,000 V
800 V
7,500 V
3,000 V
400 V
Walking across vinyl floor
Motions of bench worker
Removing DIPS from plastic tube
Removing DIPS from vinyl tray
Removing DIPS from Styrofoam
Removing bubble pack from PCB
Packing PCBs in foam-lined box
700 V
400 V
4,000 V
5,000 V
20,000 V
11,000 V
2,000 V
3,500 V
7,000 V
5,000 V
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
■
■
■
■
■
■
■
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
Keep ESD-sensitive parts in their containers until they arrive at static-free workstations.
Place items on a grounded surface before them from their containers.
Always be properly grounded when touching a component or assembly.
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam.
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized equipment
used for moving materials is wired to ground, and that proper materials are selected to avoid static charging.
When grounding is not possible, use an ionizer to dissipate electric charges.
Maintenance and Service Guide
4–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Workstation guidelines
Follow these workstation grounding guidelines:
■
■
Cover the workstation with approved static-shielding material.
Use a wrist strap connected to a properly grounded work surface, and use properly grounded tools and
equipment.
■
■
■
■
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe materials.
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and Styrofoam.
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these items
only at static-free workstations.
■
■
Avoid contact with pins, leads, or circuitry.
Turn off power and input signals before inserting or removing connectors or test equipment.
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
■
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a
minimum of one megohm 10% resistance in the ground cords. To provide proper ground, wear a strap snugly
against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a
wrist strap.
■
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can be used at
standing workstations and are compatible with most types of shoes or boots. On conductive floors or
dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance between the
operator and ground. To be effective, the conductive strips must be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
■
■
■
■
■
■
■
■
■
■
■
■
Antistatic tape
Antistatic smocks, aprons, and sleeve protectors
Conductive bins and other assembly or soldering aids
Nonconductive foam
Conductive tabletop workstations with ground cords of one megohm resistance
Static-dissipative tables or floor mats with hard ties to the ground
Field service kits
Static awareness labels
Material-handling packages
Nonconductive plastic bags, tubes, or boxes
Metal tote boxes
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material
Use
Voltage protection level
1,500 V
Antistatic plastic
Carbon-loaded plastic
Metallized laminate
Bags
Floor mats
Floor mats
7,500 V
5,000 V
4–4
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 62 screws, in 12 different sizes, that must be removed, replaced, or loosened when servicing
the computer. Make special note of each screw size and location during removal and replacement.
Serial number location
The serial number location, located on the bottom of the computer, provides important information that you may
need when contacting technical support.
Serial number label location, format, and color vary on select models.
✎
(1)
(2)
(3)
Product name
Serial number
Product number
(4)
(5)
Warranty period
Model description
Maintenance and Service Guide
4–5
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Computer feet
The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Feet Kit, spare part
number 581101-001. There are 6 rubber feet that attach to the base enclosure in the locations shown in the
following illustration.
The four rubber feet 1 in the corners of the computer are larger than the two rubber feet 2 in the middle of
the computer.
✎
4–6
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Battery
Description
Spare part number
580956-001
4-cell, 41-WHr, 2.8-Ah battery
6-cell, 62-WHr, 2.8-Ah battery (supports HP Fast Charge technology)
594796-001
Before removing the battery, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the battery:
1. Turn the computer upside down on a flat surface, with the front toward you.
2. Slide the battery release latch 1 to release the battery.
3. Pivot the front edge of the battery 2 upward.
4. Remove the battery 3.
Install the battery by inserting it into the battery bay and pivoting it downward until it is seated. The battery release
latch automatically locks the battery into place.
Maintenance and Service Guide
4–7
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
SIM
The SIM is provided by the end user as a security measure for the WWAN module. The SIM should be removed,
placed into a static-dissipative container, and then replaced when the computer is reassembled.
✎
Before removing the SIM, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the SIM:
1. Press in on the SIM 1 to release it from the SIM slot.
2. Remove the SIM 2 from the SIM slot.
Install the SIM by inserting it into the SIM slot until you hear a click.
4–8
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Mass storage device
The mass storage device spare part kit includes a bracket.
✎
Description
Spare part number
Hard drive:
500-GB, 7200 rpm
320-GB, 7200 rpm
250-GB, 7200 rpm
618829-001
581084-001
581083-001
Solid-state drive (only with computer models running Windows 7 operating system, either 2 GB or 4 GB):
128-GB
80-GB
581085-001
581086-001
Before removing the mass storage device, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the mass storage device:
1. Position the computer with the front toward you.
2. Loosen the two Phillips PM2.5×6.0 captive screws that secure the accessory cover to the computer.
3. Slide the rear edge 1 of the accessory cover to detach it from the computer.
4. Remove the accessory cover 2. The accessory cover is included in the Plastics Kit, spare part number
618835-001.
Maintenance and Service Guide
4–9
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
5. Loosen the Phillips PM2.5×11.0 captive screw 1 that secures the mass storage device in the mass storage
device bay.
6. Remove the two Phillips PM2.5×4.0 screws 2 that secure the mass storage device in the mass storage
device bay.
7. Grasp the Mylar tab 1 on the mass storage device bracket, and slide the mass storage device to the left 2 to
disconnect it from the system board.
8. Remove the mass storage device 3 from the mass storage device bay.
4–10
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
9. If it is necessary to replace the mass storage device bracket, follow these steps:
a. Remove the four Phillips PM3.0×4.0 screws 1 that secure the mass storage device bracket to the mass
storage device.
b. Lift the bracket 2 straight up to remove it from the mass storage device.
Reverse this procedure to reassemble and install the mass storage device.
Maintenance and Service Guide
4–11
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Bluetooth module
The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is
included in the Cable Kit, spare part number 618826-001.
✎
Description
Spare part number
Bluetooth module
537921-001
Before removing the Bluetooth module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the Bluetooth module:
1. Release the Bluetooth module 1 by sliding it to the left until the right side of the module is clear of the opening
in the base enclosure, and then swinging the right side of the module 2 away from the base enclosure.
4–12
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
2. Disconnect the Bluetooth module cable from the Bluetooth module.
3. Remove the Bluetooth module.
Reverse this procedure to install the Bluetooth module.
Maintenance and Service Guide
4–13
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
WLAN module
Description
Spare part number
802.11 a/b/g/n WLAN module:
Broadcom 43224 802.11 a/b/g/n WLAN module for use in Antigua and Barbuda, Barbados, Belize,
Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands,
and the United States
582564-001
Broadcom 43224 802.11 a/b/g/n WLAN module for use in Afghanistan, Albania, Algeria, Andorra,
Angola, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,
Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, the Central African Republic, Chad,
Chile, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark,
Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador,
Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia,
Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland,
Italy, the Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan,
Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia,
Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique,
Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger,
Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay,
the People’s Republic of China, Peru, the Philippines, Poland, Portugal, Qatar,
582564-002
the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe,
Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia,
the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis,
St. Lucia, St. Vincent, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania,
Thailand, Togo, Tonga, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine,
the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zaire, Zambia, and Zimbabwe
802.11 b/g/n WLAN module:
Broadcom 4312G 802.11 b/g/n WLAN module for use in Canada, the Cayman Islands, Guam,
Puerto Rico, the United States, and the U.S. Virgin Islands
593836-001
Before removing the WLAN module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
4–14
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Remove the WLAN module:
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the
computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and
then receive a warning message, remove the module to restore computer functionality, and then contact technical support through
Help and Support.
Ä
1. Position the computer with the front toward you.
2. Disconnect the WLAN antenna cables from the terminals on the WLAN module.
The black WLAN antenna cable is connected to the WLAN module “Main” terminal. The white WLAN
antenna cable is connected to the WLAN module “Aux” terminal.
✎
3. Remove the Phillips PM2.5×4.0 screw that secures the WLAN module to the system board. (The WLAN
module tilts up.)
Maintenance and Service Guide
4–15
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
4. Remove the WLAN module by pulling it away from the slot at an angle.
WLAN modules are designed with a notch to prevent incorrect insertion of the WLAN module into the
WLAN module slot.
✎
If the WLAN antennas are not connected to the terminals on the WLAN module, the protective sleeves must be
installed on the antenna connectors, as shown in the following illustration.
✎
Reverse this procedure to install the WLAN module.
4–16
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
WWAN module
Description
Spare part number
UNDP HSPA EV-DO WWAN module (does not support Linux operating system; available in all
countries and regions, except China)
531993-001
Before removing the WWAN module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the WWAN module:
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the
computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and
then receive a warning message, remove the module to restore computer functionality, and then contact technical support through
Help and Support.
Ä
1. Position the computer with the front toward you.
2. Disconnect the WWAN antenna cables from the terminals on the WWAN module.
The red WWAN antenna cable is connected to the WWAN module “Main” terminal. The blue WWAN
antenna cable is connected to the WWAN module “Aux” terminal.
✎
Maintenance and Service Guide
4–17
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
3. Remove the Phillips PM2.5×4.0 screw that secures the WWAN module to the system board. (The WWAN
module tilts up.)
4. Remove the WWAN module by pulling it away from the slot at an angle.
WWAN modules are designed with a notch to prevent incorrect insertion of the WWAN module into the
WWAN module slot.
✎
4–18
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
If the WWAN antennas are not connected to the terminals on the WWAN module, the protective sleeves must be
installed on the antenna connectors, as shown in the following illustration.
✎
Reverse this procedure to install the WWAN module.
Maintenance and Service Guide
4–19
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
RTC battery
Description
Spare part number
RTC battery (includes double-sided tape)
481089-001
Before removing the RTC battery, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the RTC battery:
1. Disconnect the RTC battery cable 1 from the system board.
2. Detach the RTC battery 2 from the system board. (The RTC battery is attached to the system board with
double-sided tape.)
Reverse this procedure to install the RTC battery.
4–20
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Memory module
Description
Spare part number
599092-001
4096-MB memory module (1333-MHz, DDR3, PC3-10600 Shared)
2048-MB memory module (1333-MHz, DDR3, PC3-10600)
581096-001
1024-MB memory module (1333-MHz, DDR3, PC3-10600 Shared) (not available on Microsoft 64-bit 598859-001
operating systems)
Before removing the memory module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the memory module:
1. Pull away the retention clips on each side of the memory module to release the memory module. (The memory
module tilts up.)
Maintenance and Service Guide
4–21
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
CAUTION: To prevent damage to the memory module, hold it by the edges only. Do not touch the components on the memory
module.
Ä
2. Grasp the edge of the memory module, and then pull it out of the memory module slot.
Memory modules are designed with a notch to prevent incorrect insertion into the memory module slot.
✎
Reverse this procedure to install a memory module.
4–22
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Keyboard
The keyboard spare part kit includes a keyboard cable.
✎
Keyboard for use in country
or region
Keyboard for use in country
Spare part number
618843-A41
618843-261
618843-A81
618843-081
618843-051
618843_DW1
618843-121
618843-041
618843-DJ1
618843-211
618843-DD1
618843-BB1
618843-061
618843-291
618843-B31
or region
Spare part number
618843-091
618843-131
618843-251
618843-171
618843-BA1
618843-AD1
618843-071
618843-B71
618843-BG1
618843-AB1
618843-281
618843-141
618843-031
618843-001
Belgium
Norway
Bulgaria
Portugal
The Czech Republic and Slovakia
Russia
Denmark
France
Saudi Arabia
Slovenia
France and Arabia
French Canada
Germany
Greece
South Korea
Spain
Sweden and Finland
Switzerland
Taiwan
Hungary
Iceland
Thailand
Israel
Turkey
Italy
The United Kingdom
The United States
Japan
The Netherlands
Before removing the keyboard, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Maintenance and Service Guide
4–23
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Remove the keyboard:
1. Position the computer with the front toward you.
2. Remove the following screws:
❏ Two Torx T8M2.5×5.0 screws 1 in the mass storage device bay and the wireless module compartment
❏ One Phillips PM2.5×2.0 broadhead screw 2 in the battery bay
3. Turn the computer display-side up, with the front toward you.
4. Open the computer as far as possible.
5. Slide the keyboard 1 back until it rests on the display.
6. Lift the rear edge of the keyboard 2 until it rests at an angle.
4–24
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
7. Release the zero insertion force (ZIF) connector 1 to which the keyboard cable is attached, disconnect the
keyboard cable 2 from the system board, and then remove the keyboard 3.
Reverse this procedure to install the keyboard.
Maintenance and Service Guide
4–25
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Button board and cable
Description
Spare part number
Button board with FFC (includes cable)
618815-001
Before removing the button board and cable, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the button board and cable:
1. Release the ZIF connector 1 to which the button board cable is attached, and then disconnect the button board
cable 2 from the system board.
2. Release the button board cable from the top cover. (The button board cable is attached to the top cover with
double-sided tape.)
4–26
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
3. Remove the Torx T8M2.5×4.0 screw that secures the button board to the top cover.
4. Lift the button board to release it from the clips built into the top cover.
5. Remove the button board and cable.
Reverse this procedure to install the button board and cable.
Maintenance and Service Guide
4–27
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Top cover
Description
Spare part number
Top cover with fingerprint reader (includes TouchPad button board and cable, and TouchPad board
618840-001
and cable)
Top cover with no fingerprint reader (includes TouchPad button board and cable, and TouchPad
board and cable)
618841-001
Before removing the top cover, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
Remove the top cover:
1. Turn the computer upside down, with the front toward you.
2. Remove the following screws:
❏ Three Torx T8M2.5×5.0 screws 1 in the battery bay
❏ Three Torx T8M2.5×6.0 screws 2 in the mass storage device bay
❏ Two Torx T8M2.5×9.0 screws 3 in the RTC battery compartment
4–28
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
3. Turn the computer display-side up, with the front toward you.
4. Open the computer as far as possible.
5. Release the ZIF connector 1 to which the power button board cable is attached, and then disconnect the power
button board cable from the system board.
6. Release the ZIF connector 2 to which the TouchPad cable is attached, and then disconnect the TouchPad cable
from the system board.
7. Remove the seven slotted Torx T8M2.5×7.0 screws that secure the top cover to the base enclosure.
Maintenance and Service Guide
4–29
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
8. Lift the rear edge 1 of the top cover until it detaches from the base enclosure.
9. Remove the top cover 2 by lifting it straight up.
Reverse this procedure to install the top cover.
4–30
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Power button board and cable
Description
Spare part number
Power button board with FFC (includes cable)
618816-001
Before removing the power button board and cable, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
Remove the power button board and cable:
1. Release the ZIF connector 1 to which the power button board cable is attached, and then disconnect the cable
from the system board.
2. Disconnect the power cable 2 from the system board.
3. Remove the two Torx T8M2.5×6.0 screws 3 that secure the power button board to the base enclosure.
4. Remove the power button board and cable 4 by lifting them straight up.
Reverse this procedure to install the power button board and cable.
Maintenance and Service Guide
4–31
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Bluetooth module cable
The Bluetooth module cable is included in the Cable Kit, spare part number 618826-001.
✎
Before removing the Bluetooth module cable, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
Remove the Bluetooth module cable:
1. Disconnect the Bluetooth module cable 1 from the system board.
2. Remove the Bluetooth module cable 2.
Reverse this procedure to install the Bluetooth module cable.
4–32
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
System board
The system board spare part kit includes a processor and replacement thermal material.
✎
Description
Spare part number
Intel® Dual Core i5-45M 2.40-GHz processor (Turbo up to 2.53 GHz), 3-M L3 cache, 4 threads
(35W)
618821-001
618822-001
618819-001
Intel® Dual Core i5-45M 2.40-GHz processor (Turbo up to 2.53 GHz), 3-M L3 cache, 4 threads
(35W), for use in China and Russia
Intel Dual Core i3-370M 2.40-GHz processor, 3-M L3 cache, 4 threads (35W)
Intel Dual Core i3-370M 2.40-GHz processor, 3-M L3 cache, 4 threads (35W), for use in China and 618820-001
Russia
Intel Dual Core i3-350M 2.26-GHz processor, 3-M L3 cache, 4 threads (35W)
618817-001
Intel Dual Core i3-350M 2.26-GHz processor, 3-M L3 cache, 4 threads (35W), for use in China and 618818-001
Russia
Intel U3400 1.06-GHz processor
618823-001
618824-001
Intel U3400 1.06-GHz processor, for use in China and Russia
Before removing the system board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
When replacing the system board, be sure that the following additional components are removed from the defective
system board and installed on the replacement system board:
■
■
■
■
■
■
■
■
Maintenance and Service Guide
4–33
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Remove the system board:
1. Turn the computer upside down, with the front toward you.
2. Disconnect the SD Card Reader board cable from the system board.
3. Turn the computer display-side up, with the front toward you.
4. Open the computer as far as possible.
5. Disconnect the speaker cable 1 from the system board.
6. Disconnect the display panel cable 2 from the system board.
7. Release the ZIF connector 3 to which the power button board board cable is attached, and then disconnect the
cable from the system board.
8. Disconnect the power cable 4 from the system board.
4–34
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
9. Remove the three Torx T8M2.5×4.0 screws that secure the system board to the base enclosure.
10. Lift the left side of the system board 1 until it rests at an angle.
11. Remove the system board 2 by sliding it away from the base enclosure at an angle.
Reverse this procedure to install the system board.
Maintenance and Service Guide
4–35
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Fan and heat sink
The fan and heat sink spare part kit includes replacement thermal material.
✎
Description
Spare part number
Fan/Heat sink
618830-001
To properly ventilate the computer, allow at least 7.6 cm (3 in) of clearance on the left side of the computer. The
computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to
turn on automatically when high temperature conditions exist. These conditions are affected by high external
temperatures, system power consumption, power management/battery conservation configurations, battery fast
charging, and software requirements. Exhaust air is displaced through the ventilation grill located on the left side
of the computer.
✎
Before removing the fan and heat sink, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
4–36
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Remove the fan and heat sink:
1. Turn the system board upside down, with the front toward you.
2. Disconnect the fan cable 1 from the system board.
3. Following the 1, 2, 3, 4 sequence stamped into the heat sink, loosen the four Torx T8M2.0×7.0 captive
screws 2 that secure the fan and heat sink to the system board.
Due to the adhesive quality of the thermal material located between the heat sink and system board
components, it may be necessary to move the heat sink from side to side to detach it.
✎
4. Remove the fan and heat sink 3.
Maintenance and Service Guide
4–37
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
The thermal material must be thoroughly cleaned from the surfaces of the heat sink and the system board
each time the heat sink is removed:
✎
❏ Thermal paste is used on the processor 1 and the heat sink section 2 that services it.
❏ Thermal pads are used on the Northbridge chip 3 and the heat sink section 4 that services it.
Replacement thermal material is included with all system board and heat sink spare part kits.
5. Lift the fan straight up to remove it from the heat sink. (The fan is attached to the heat sink with
double-sided tape.)
Reverse this procedure to install the fan and heat sink.
4–38
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Speaker assembly
Description
Spare part number
Speaker assembly (includes cable)
618839-001
Before removing the speaker assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
Remove the speaker assembly:
1. Remove the three Torx T8M2.5×4.0 screws 1 that secure the speaker assembly to the base enclosure.
2. Remove the speaker assembly 2.
Reverse this procedure to install the speaker assembly.
Maintenance and Service Guide
4–39
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
USB board
Description
Spare part number
USB board (includes cable)
618825-001
Before removing the USB board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
Remove the USB board:
1. Disconnect the microphone cable 1 from the USB board.
2. Remove the two Torx T8M2.5×4.0 screws 2 that secure the USB board to the base enclosure.
3. Remove the USB board 3 and cable.
Reverse this procedure to install the USB board.
4–40
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Battery eject arm
Description
Spare part number
Latch Kit (includes battery eject arm, latch, and spring)
581090-001
Before removing the battery eject arm, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
Remove the battery eject arm:
1. Turn the base enclosure upside down, with the front toward you.
2. Use a flat-bladed screw driver 1 or similar tool to release the battery eject latch from the base enclosure.
3. Remove the the battery eject latch 2.
Maintenance and Service Guide
4–41
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
4. Release the battery eject arm spring 1 from the tab built into the base enclosure.
5. Remove the two Phillips PM2.5×4.0 broadhead screws 2 that secure the battery eject arm to the
base enclosure.
6. Remove the the battery eject arm 3.
Reverse this procedure to install the battery eject arm.
4–42
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
Display assembly
The display assembly spare part kit includes 2 WLAN antenna transceivers and cables, 2 WWAN antenna
transceivers and cables, webcam, nameplate, and logo.
✎
Description
Spare part number
618827-001
13.3-in, HD, LED, AntiGlare display assembly
13.3-in, HD, LED, BrightView display assembly
618828-001
Before removing the display assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
Remove the display assembly:
1. Remove the WLAN and WWAN antenna cables 1 from the clips 2 built into the base enclosure.
Maintenance and Service Guide
4–43
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
CAUTION: Support the display assembly when removing the following screws. Failure to support the display
assembly can result in damage to the display assembly and other computer components.
Ä
2. Remove the two Torx T8M2.5×4.0 screws 1 and the Torx T8M2.5×9.0 screw 2 that secure the display
assembly to the base enclosure.
3. Lift the display assembly 3 straight up and remove it.
4. If it is necessary to replace the display bezel or any of the display assembly internal components:
a. Remove the two rubber screw covers 1 and the two Phillips PM2.5×5.0 screws 2 that secure the display
bezel to the display enclosure.
4–44
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
b. Flex the inside edges of the top edge 1, the left and right sides 2, and the bottom edge 3 of the display
bezel until the bezel disengages from the display enclosure.
c. Remove the display bezel 4. The display bezel is available using spare part number 618832-001.
5. If it is necessary to replace the webcam module:
a. Release the webcam module 1 as far from the display enclosure as the webcam module cable allows.
(The webcam module is attached to the display enclosure with double-sided tape.)
b. Disconnect the webcam module cable 2 from the webcam module.
c. Remove the webcam module. The webcam module is available using spare part number 618842-001.
Maintenance and Service Guide
4–45
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
6. If it is necessary to replace the display hinges:
a. Remove the eight Torx T8M2.5×4.0 screws 1 that secure the display hinges to the display enclosure.
b. Remove the display hinges 2. The display hinges are available in the Display Hinge Kit, spare part number
581094-001.
4–46
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
7. If it is necessary to replace the display panel cable:
a. Lift the top edge of the display panel 1 until it detaches from the display enclosure.
b. Release the support bar 2 that secures the display panel cable connector to the display panel.
c. Disconnect the display panel cable 3 from the display panel.
d. Remove the display panel.
e. Remove the display panel cable. The display panel cable is included in the Display Cable Kit, spare
part number 618833-001.
Maintenance and Service Guide
4–47
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
8. If it is necessary to replace the WWAN antenna transceivers and cables:
a. Detach the WWAN antenna transceivers 1 from the display enclosure. (The transceivers are attached to the
enclosure with double-sided tape.)
b. Release the WWAN antenna cables 2 from the clips and routing channels built into the left and right sides
of the display enclosure.
c. Remove the WWAN wireless antenna transceivers and cables. The wireless antenna transceivers and cables
are included in the Display Cable Kit, spare part number 618833-001.
4–48
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
9. If it is necessary to replace the WLAN antenna transceivers and cables:
a. Detach the WLAN antenna transceivers 1 from the display enclosure. (The transceivers are attached to the
enclosure with double-sided tape.)
b. Release the WLAN antenna cables 2 from the clips and routing channel built into the left and right sides of
the display enclosure.
c. Remove the WLAN wireless antenna transceivers and cables. The wireless antenna transceivers and cables
are included in the Display Cable Kit, spare part number 618833-001.
10. If it is necessary to replace the microphones and cables:
a. Release the microphone receivers 1 from the clips built into the display enclosure.
b. Release the microphone cables 2 from the clips and routing channel built into the left side of the
display enclosure.
c. Remove the microphones and cables. The microphones and cables are included in the Display Cable Kit,
spare part number 618833-001.
Reverse this procedure to reassemble and install the display assembly.
Maintenance and Service Guide
4–49
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and replacement procedures
4–50
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Computer Setup
Computer Setup in Windows 7
Starting Computer Setup
Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not
working or will not load.
Some of the Computer Setup menu items listed in this guide may not be supported by your computer.
✎
✎
An external keyboard or mouse connected to a USB port can be used with Computer Setup only if USB legacy
support is enabled.
To start Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
Using Computer Setup
Navigating and selecting in Computer Setup
The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and System
Configuration menus.
To navigate and select in Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
❏ To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press enter, or use a
pointing device to click the item.
❏ To scroll up and down, click the up arrow or the down arrow in the upper-right corner of the screen, or use
the up arrow key or the down arrow key.
❏ To close open dialog boxes and return to the main Computer Setup screen, press esc, and then follow the
on-screen instructions.
You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard to navigate and
make selections in Computer Setup.
✎
2. Press f10 to enter BIOS Setup.
3. Select the File, Security, Diagnostics, or System Configuration menu.
Maintenance and Service Guide
5–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
To exit Computer Setup menus, choose one of the following methods:
■
To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Ignore Changes and Exit, and then press enter.
– or –
■
To save your changes and exit Computer Setup menus, click the Save icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Restoring factory settings in Computer Setup
Restoring defaults will not change the hard drive mode.
✎
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
3. Use a pointing device or the arrow keys to select File > Restore Defaults.
4. Follow the on-screen instructions.
5. To save your changes and exit, click the Save icon in the lower-left corner of the screen, and then follow the
on-screen instructions.
– or –
Use the arrow keys to select File > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Your password settings and security settings are not changed when you restore the factory settings.
✎
5–2
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Computer Setup menus
The menu tables in this section provide an overview of Computer Setup options.
Some of the Computer Setup menu items listed in this chapter may not be supported by your computer.
✎
File menu
Select
To do this
System Information
■ View identification information for the computer and
the batteries in the system.
■ View specification information for the processor, memory
size, system ROM, video revision, and keyboard controller
version, and wireless identification numbers.
Restore Defaults
Replace the configuration settings in Computer Setup with
the original factory settings. (Hard drive mode, password
settings, and security settings are not changed when you
restore the factory settings.)
Reset BIOS security to factory default
Ignore Changes and Exit
Resets password to the factory default in case of a forgotten
password.
Cancel any changes entered during the current session.
Then exit and restart the computer.
Save Changes and Exit
Save any changes entered during the current session.
Then exit and restart the computer. Your changes go into
effect when the computer restarts.
Security menu
Some of the menu items listed in this section may not be supported by your computer.
✎
Select
To do this
Setup BIOS Administrator Password
Set up a BIOS administrator password.
User Management (requires a BIOS administrator password) ■ Create a new BIOS user account.
■ View a list of ProtectTools users.
Password Policy (requires a BIOS administrator password)
HP SpareKey
Revise password policy criteria.
Enable/disable HP SpareKey (enabled by default).
Enable/disable HP SpareKey enrollment (enabled by default).
Always Prompt for HP SpareKey Enrollment
Fingerprint Reset on Reboot (If Present)
Reset/clear the fingerprint reader ownership (select models
only; disabled by default).
Allow reset of HP ProtectTools security keys
Change Password
Enable/disable reset of HP ProtectTools security keys.
Enter, change, or delete a BIOS administrator password.
HP SpareKey Enrollment
Enroll or reset HP SpareKey, which is a set of security
questions and answers used if you forget your password.
(Continued)
Maintenance and Service Guide
5–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Select
To do this
Security menu (continued)
DriveLock Passwords
■ Enable/disable DriveLock on any computer hard drive
(enabled by default).
■ Change a DriveLock user password or master password.
DriveLock settings are accessible only when you enter
✎
Computer Setup by turning on (not restarting)
the computer.
TPM Embedded Security
Enable/disable support for Trusted Platform Module (TPM)
Embedded Security, which protects the computer from
unauthorized access to owner functions available in
Embedded Security for ProtectTools. For more information,
refer to the ProtectTools software Help.
You must have a setup password to change this
setting.
✎
Automatic DriveLock
Disk Sanitizer
Enable/disable Automatic DriveLock support.
Run Disk Sanitizer to destroy all existing data on the primary
hard drive or the drive in the upgrade bay.
If you run Disk Sanitizer, the data on the selected drive
is destroyed permanently.
✎
System IDs
Enter a user-defined computer asset tracking number and
ownership tag.
Diagnostics menu
Select
To do this
System Diagnostics menu
■ F1 System Information—Displays the
following information:
❐ Identification information for the computer and the
batteries in the system.
❐ Specification information for the processor, memory
size, system ROM, video revision, keyboard controller
version, and wireless identification numbers.
■ F2 Start-up Test—Verifies the system components needed
for starting the computer.
■ F3 Run-In Test—Runs a comprehensive check on
system memory.
■ F4 Hard Disk Test—Runs a comprehensive self-test on
any hard drive in the system.
■ F5 Error Log—Displays a log file if any errors
have occurred.
5–4
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
System Configuration menu
Some of the listed System Configuration options may not be supported by your computer.
✎
Select
To do this
Language
Boot Options
Change the Computer Setup language.
■ Set a Startup Menu delay (in seconds).
■ Enable/disable Custom Logo (disabled by default).
■ Enable/disable Display Diagnostic URL (enabled
by default).
■ Enable/disable CD-ROM boot (enabled by default).
■ Enable/disable SD Card boot (enabled by default).
■ Enable/disable floppy boot (enabled by default).
■ Enable/disable PXE Internal NIC boot (enabled by default).
■ Set the Express Boot Popup delay in seconds.
■ Set the boot order.
Device Configurations
■ Enable/disable USB legacy support (enabled by default).
When enabled, USB legacy support allows the following:
❐ Use of a USB keyboard in Computer Setup even when a
Windows operating system is not running.
❐ Startup from bootable USB devices, including a hard
drive, diskette drive, or optical drive connected by a USB
port to the computer.
■ Select a parallel port mode: ECP (Enhanced Capabilities
Port), standard, bidirectional, or EPP (Enhanced
Parallel Port).
■ Enable/disable fan always on while connected to an AC
outlet (enabled by default).
■ Enable/disable Data Execution Prevention. When enabled,
the processor can disable some virus code execution,
which helps to improve computer security.
■ Enable/disable LAN Power Save (select models only).
When enabled, saves power by turning off the LAN when
not in use (enabled by default).
■ SATA (Serial Advanced Technology Attachment) device
mode. The following options are available:
❐ AHCI (Advanced Host Controller Interface)
❐ IDE (Integrated Drive Electronics)
❐ RAID (select models only)
Availability of the options above varies by
computer model.
✎
■ Enable/disable secondary battery fast charge (enabled by
default).
■ Enable/disable HP QuickLook 3 (enabled by default).
■ Enable/disable Virtualization Technology (select models
only; disabled by default).
■ Enable/disable TXT (Intel Trusted Execution Technology)
(select models only; disabled by default).
(Continued)
Maintenance and Service Guide
5–5
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Select
To do this
System Configuration menu (continued)
Device Configurations (continued)
■ Enable/disable Dual Core CPU (select models only;
enabled by default).
■ Enable/Disable Unified Extensible Firmware Interface
(UEFI) mode (disabled by default).
■ Turn the Numlock state at boot on or off.
Built-In Device Options
■ Enable/disable the wireless button state (enabled
by default).
■ Enable/disable the embedded WLAN device (enabled
by default).
■ Enable/disable embedded WWAN device radio (select
models only; enabled by default).
■ Enable/disable embedded Bluetooth device radio (enabled
by default).
■ Enable/disable the Network Interface Controller (LAN)
(enabled by default).
■ Enable/disable LAN/WLAN switching (disabled by default).
■ Set the wake on LAN state. Options include the following:
❐ Disabled
❐ Boot to Network (set by default)
❐ Follow Boot Order
■ Enable/disable the fingerprint device (enabled by default).
■ Enable/disable a modem device (enabled by default).
■ Enable the ambient light sensor (enabled by default).
■ Enable/disable the Notebook MultiBay device (enabled
by default).
■ Enable/disable the integrated camera (select models only;
enabled by default).
■ Enable/disable optical disk drive (enabled by default).
■ Enable/disable internal microphones (enabled by default).
Port Options (all are enabled by default)
All port options are enabled by default.
✎
■ Enable/disable the Smart Card slot.
■ Enable/disable the ExpressCard slot.
■ Enable/disable the serial port.
■ Enable/disable the parallel port.
■ Enable/disable the flash media reader.
■ Enable/disable the USB port.
Disabling the USB port also disables MultiBay devices
and ExpressCard devices on the advanced
Ä
port replicator.
■ Enable/disable the 1394 port.
Set Security Level
Change, view, or hide security levels for all BIOS menu items.
Restore the default security settings.
Restore Security Defaults
5–6
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Computer Setup in Windows Vista
Starting Computer Setup
Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not
working or will not load.
Some of the Computer Setup menu items listed in this guide may not be supported by your computer.
✎
✎
An external keyboard or mouse connected to a USB port can be used with Computer Setup only if USB legacy
support is enabled.
To start Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
Using Computer Setup
Navigating and selecting in Computer Setup
The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and System
Configuration menus.
To navigate and select in Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
❏ To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press enter, or use a
pointing device to click the item.
❏ To scroll up and down, click the up arrow or the down arrow in the upper-right corner of the screen, or use
the up arrow key or the down arrow key.
❏ To close open dialog boxes and return to the main Computer Setup screen, press esc, and then follow the
on-screen instructions.
You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard to navigate
and make selections in Computer Setup.
✎
2. Press f10 to enter BIOS Setup.
3. Select the File, Security, Diagnostics, or System Configuration menu.
To exit Computer Setup menus, choose one of the following methods:
■
To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Ignore Changes and Exit, and then press enter.
– or –
■
To save your changes and exit Computer Setup menus, click the Save icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Maintenance and Service Guide
5–7
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Restoring factory settings in Computer Setup
Restoring defaults will not change the hard drive mode.
✎
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
3. Use a pointing device or the arrow keys to select File > Restore Defaults.
4. Follow the on-screen instructions.
5. To save your changes and exit, click the Save icon in the lower-left corner of the screen, and then follow the
on-screen instructions.
– or –
Use the arrow keys to select File > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Your password settings and security settings are not changed when you restore the factory settings.
✎
Computer Setup menus
The menu tables in this section provide an overview of Computer Setup options.
Some of the Computer Setup menu items listed in this chapter may not be supported by your computer.
✎
File menu
Select
To do this
System Information
■ View identification information for the computer and the
batteries in the system.
■ View specification information for the processor, memory
size, system ROM, video revision, keyboard controller
version, and wireless identification numbers.
Restore Defaults
Replace the configuration settings in Computer Setup with
the original factory settings. (Hard drive mode, password
settings, and security settings are not changed when you
restore the factory settings.)
Reset BIOS security to factory default
Ignore Changes and Exit
Resets password to the factory default in case of a forgotten
password.
Cancel any changes entered during the current session. Then
exit and restart the computer.
Save Changes and Exit
Save any changes entered during the current session. Then
exit and restart the computer. Your changes go into effect
when the computer restarts.
5–8
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Security menu
Some of the menu items listed in this section may not be supported by your computer.
✎
Select
To do this
Setup BIOS Administrator Password
Set up a BIOS administrator password.
User Management (requires a BIOS administrator password) ■ Create a new BIOS user account.
■ View a list of ProtectTools users.
Password Policy (requires a BIOS administrator password)
HP SpareKey
Revise password policy criteria.
Enable/disable HP SpareKey (enabled by default).
Always Prompt for HP SpareKey Enrollment
Fingerprint Reset on Reboot (If Present)
Enable/disable HP SpareKey enrollment (enabled by default).
Reset/clear the fingerprint reader ownership (select models
only; disabled by default).
Allow reset of HP ProtectTools security keys
Change Password
Enable/disable reset of HP ProtectTools security keys.
Enter, change, or delete a BIOS administrator password.
HP SpareKey Enrollment
Enroll or reset HP SpareKey, which is a set of security
questions and answers used if you forget your password.
DriveLock Passwords
■ Enable/disable DriveLock on any computer hard drive
(enabled by default).
■ Change a DriveLock user password or master password.
DriveLock settings are accessible only when you enter
✎
Computer Setup by turning on (not restarting)
the computer.
TPM Embedded Security
Enable/disable support for Trusted Platform Module (TPM)
Embedded Security, which protects the computer from
unauthorized access to owner functions available in
Embedded Security for ProtectTools. For more information,
refer to the ProtectTools software Help.
You must have a setup password to change
this setting.
✎
Automatic DriveLock
Disk Sanitizer
Enable/disable Automatic DriveLock support.
Run Disk Sanitizer to destroy all existing data on the primary
hard drive or the drive in the upgrade bay.
If you run Disk Sanitizer, the data on the selected drive
is destroyed permanently.
Ä
System IDs
Enter a user-defined computer asset tracking number and
ownership tag.
Maintenance and Service Guide
5–9
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Diagnostics menu
Select
To do this
System Diagnostics menu
■ F1 System Information—Displays the
following information:
❐ Identification information for the computer and the
batteries in the system.
❐ Specification information for the processor, memory
size, system ROM, video revision, keyboard controller
version, and wireless identification numbers.
■ F2 Start-up Test—Verifies the system components needed
for starting the computer.
■ F3 Run-In Test—Runs a comprehensive check on
system memory.
■ F4 Hard Disk Test—Runs a comprehensive self-test on
any hard drive in the system.
■ F5 Error Log—Displays a log file if any errors
have occurred.
System Configuration menu
Some of the listed System Configuration options may not be supported by your computer.
✎
Select
To do this
Language
Boot Options
Change the Computer Setup language.
■ Set a Startup Menu delay (in seconds).
■ Enable/disable Custom Logo (disabled by default).
■ Enable/disable Display Diagnostic URL (enabled
by default).
■ Enable/disable CD-ROM boot (enabled by default).
■ Enable/disable SD Card boot (enabled by default).
■ Enable/disable floppy boot (enabled by default).
■ Enable/disable PXE Internal NIC boot (enabled by default).
■ Set the Express Boot Popup delay in seconds.
■ Set the boot order.
Device Configurations
■ Enable/disable USB legacy support (enabled by default).
When enabled, USB legacy support allows the following:
❐ Use of a USB keyboard in Computer Setup even when a
Windows operating system is not running.
❐ Startup from bootable USB devices, including a hard
drive, diskette drive, or optical drive connected by a USB
port to the computer.
■ Select a parallel port mode: ECP (Enhanced Capabilities
Port), standard, bidirectional, or EPP (Enhanced
Parallel Port).
■ Enable/disable fan always on while connected to an AC
outlet (enabled by default).
(Continued)
5–10
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Select
To do this
System Configuration menu (continued)
Device Configurations (continued)
■ Enable/disable Data Execution Prevention. When enabled,
the processor can disable some virus code execution,
which helps to improve computer security.
■ Enable/disable LAN Power Save (select models only).
When enabled, saves power by turning off the LAN when
not in use (enabled by default).
■ SATA (Serial Advanced Technology Attachment) device
mode. The following options are available:
❐ AHCI (Advanced Host Controller Interface)
❐ IDE (Integrated Drive Electronics)
❐ RAID (select models only)
Availability of the options above varies by
computer model.
✎
■ Enable/disable secondary battery fast charge (enabled
by default).
■ Enable/disable HP QuickLook 3 (enabled by default).
■ Enable/disable Virtualization Technology (select models
only; disabled by default).
■ Enable/disable TXT (Intel Trusted Execution Technology)
(select models only; disabled by default).
■ Enable/disable Dual Core CPU (select models only;
enabled by default).
■ Enable/Disable Unified Extensible Firmware Interface
(UEFI) mode (disabled by default).
■ Turn the Numlock state at boot on or off.
Built-In Device Options
■ Enable/disable the wireless button state (enabled
by default).
■ Enable/disable the embedded WLAN device (enabled
by default).
■ Enable/disable embedded WWAN device radio (select
models only; enabled by default).
■ Enable/disable embedded Bluetooth device radio (enabled
by default).
■ Enable/disable the Network Interface Controller (LAN)
(enabled by default).
■ Enable/disable LAN/WLAN switching (disabled by default).
■ Set the wake on LAN state. Options include the following:
❐ Disabled
❐ Boot to Network (set by default)
❐ Follow Boot Order
■ Enable/disable the fingerprint device (enabled by default).
(Continued)
Maintenance and Service Guide
5–11
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Select
To do this
System Configuration menu (continued)
Built-In Device Options (continued)
■ Enable/disable a modem device (enabled by default).
■ Enable the ambient light sensor (enabled by default).
■ Enable/disable the Notebook MultiBay device (enabled
by default).
■ Enable/disable the integrated camera (select models only;
enabled by default).
■ Enable/disable optical disk drive (enabled by default).
■ Enable/disable internal microphones (enabled by default).
Port Options (all are enabled by default)
All port options are enabled by default.
✎
■ Enable/disable the Smart Card slot.
■ Enable/disable the ExpressCard slot.
■ Enable/disable the serial port.
■ Enable/disable the parallel port.
■ Enable/disable the flash media reader.
■ Enable/disable the USB port.
Disabling the USB port also disables MultiBay devices
and ExpressCard devices on the advanced
Ä
port replicator.
■ Enable/disable the 1394 port.
Set Security Level
Change, view, or hide security levels for all BIOS menu items.
Restore the default security settings.
Restore Security Defaults
5–12
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Computer Setup in Windows XP
Starting Computer Setup
Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not
working or will not load.
Some of the Computer Setup menu items listed in this guide may not be supported by your computer.
✎
✎
An external keyboard or mouse connected to a USB port can be used with Computer Setup only if USB legacy
support is enabled.
To start Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
Using Computer Setup
Navigating and selecting in Computer Setup
The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and System
Configuration menus.
To navigate and select in Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
❏ To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press enter, or use a
pointing device to click the item.
❏ To scroll up and down, click the up arrow or the down arrow in the upper-right corner of the screen, or use
the up arrow key or the down arrow key.
❏ To close open dialog boxes and return to the main Computer Setup screen, press esc, and then follow the
on-screen instructions.
You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard to
navigate and make selections in Computer Setup.
✎
2. Press f10 to enter BIOS Setup.
3. Select the File, Security, Diagnostics, or System Configuration menu.
To exit Computer Setup menus, choose one of the following methods:
■
To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Ignore Changes and Exit, and then press enter.
– or –
■
To save your changes and exit Computer Setup menus, click the Save icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Save Changes and Exit, and then press enter.
Maintenance and Service Guide
5–13
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Your changes go into effect when the computer restarts.
Restoring factory settings in Computer Setup
Restoring defaults will not change the hard drive mode.
✎
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
3. Use a pointing device or the arrow keys to select File > Restore Defaults.
4. Follow the on-screen instructions.
5. To save your changes and exit, click the Save icon in the lower-left corner of the screen, and then follow the
on-screen instructions.
– or –
Use the arrow keys to select File > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Your password settings and security settings are not changed when you restore the factory settings.
✎
Computer Setup menus
The menu tables in this section provide an overview of Computer Setup options.
Some of the Computer Setup menu items listed in this chapter may not be supported by your computer.
✎
File menu
Select
To do this
System Information
■ View identification information for the computer and
the batteries in the system.
■ View specification information for the processor, memory
size, system ROM, video revision, keyboard controller
version, and wireless identification version.
Restore Defaults
Replace the configuration settings in Computer Setup with
the original factory settings. (Hard drive mode, password
settings, and security settings are not changed when you
restore the factory settings.)
Reset BIOS security to factory default
Ignore Changes and Exit
Resets password to the factory default in case of a
forgotten password.
Cancel any changes entered during the current session.
Then exit and restart the computer.
Save Changes and Exit
Save any changes entered during the current session.
Then exit and restart the computer. Your changes go into
effect when the computer restarts.
5–14
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Security menu
Some of the menu items listed in this section may not be supported by your computer.
✎
Select
To do this
Setup BIOS Administrator Password
Set up a BIOS administrator password.
User Management (requires a BIOS administrator password) ■ Create a new BIOS user account.
■ View a list of ProtectTools users.
Password Policy (requires a BIOS administrator password)
HP SpareKey
Revise password policy criteria.
Enable/disable HP SpareKey (enabled by default).
Always Prompt for HP SpareKey Enrollment
Fingerprint Reset on Reboot (If Present)
Enable/disable HP SpareKey enrollment (enabled by default).
Reset/clear the fingerprint reader ownership (select models
only; disabled by default).
Allow reset of HP ProtectTools security keys
Change Password
Enable/disable reset of HP ProtectTools security keys.
Enter, change, or delete a BIOS administrator password.
HP SpareKey Enrollment
Enroll or reset HP SpareKey, which is a set of security
questions and answers used if you forget your password.
DriveLock Passwords
■ Enable/disable DriveLock on any computer hard drive
(enabled by default).
■ Change a DriveLock user password or master password.
DriveLock settings are accessible only when you enter
✎
Computer Setup by turning on (not restarting)
the computer.
TPM Embedded Security
Enable/disable support for Trusted Platform Module (TPM)
Embedded Security, which protects the computer from
unauthorized access to owner functions available in
Embedded Security for ProtectTools. For more information,
refer to the ProtectTools software Help.
You must have a setup password to change
this setting.
✎
Automatic DriveLock
Disk Sanitizer
Enable/disable Automatic DriveLock support.
Run Disk Sanitizer to destroy all existing data on the primary
hard drive or the drive in the upgrade bay.
If you run Disk Sanitizer, the data on the selected drive
is destroyed permanently.
Ä
System IDs
Enter a user-defined computer asset tracking number and
ownership tag.
Maintenance and Service Guide
5–15
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Diagnostics menu
Select
To do this
System Diagnostics menu
■ F1 System Information—Displays the
following information:
❐ Identification information for the computer and the
batteries in the system.
❐ Specification information for the processor, memory
size, system ROM, video revision, keyboard controller
version, and wireless identification numbers.
■ F2 Start-up Test—Verifies the system components needed
for starting the computer.
■ F3 Run-In Test—Runs a comprehensive check on
system memory.
■ F4 Hard Disk Test—Runs a comprehensive self-test on
any hard drive in the system.
■ F5 Error Log—Displays a log file if any errors have
occurred.
5–16
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
System Configuration menu
Some of the listed System Configuration options may not be supported by your computer.
✎
Select
To do this
Language
Boot Options
Change the Computer Setup language.
■ Set a Startup Menu delay (in seconds).
■ Enable/disable Custom Logo (disabled by default).
■ Enable/disable Display Diagnostic URL (enabled
by default).
■ Enable/disable CD-ROM boot (enabled by default).
■ Enable/disable SD Card boot (enabled by default).
■ Enable/disable floppy boot (enabled by default).
■ Enable/disable PXE Internal NIC boot (enabled by default).
■ Set the Express Boot Popup delay in seconds.
■ Set the boot order.
Device Configurations
■ Enable/disable USB legacy support (enabled by default).
When enabled, USB legacy support allows the following:
❐ Use of a USB keyboard in Computer Setup even when a
Windows operating system is not running.
❐ Startup from bootable USB devices, including
a hard drive, diskette drive, or optical drive connected by
a USB port to the computer.
■ Select a parallel port mode: ECP (Enhanced Capabilities
Port), standard, bidirectional, or EPP (Enhanced
Parallel Port).
■ Enable/disable fan always on while connected to an
AC outlet (enabled by default).
■ Enable/disable Data Execution Prevention. When enabled,
the processor can disable some virus code execution,
which helps to improve computer security.
■ Enable/disable LAN Power Save (select models only).
When enabled, saves power by turning off the LAN when
not in use (enabled by default).
■ SATA (Serial Advanced Technology Attachment) device
mode. The following options are available:
❐ AHCI (Advanced Host Controller Interface)
❐ IDE (Integrated Drive Electronics)
❐ RAID (select models only)
Availability of the options above varies by
computer model.
✎
■ Enable/disable secondary battery fast charge (enabled
by default).
■ Enable/disable HP QuickLook 3 (enabled by default).
■ Enable/disable Virtualization Technology (select models
only; disabled by default).
■ Enable/disable TXT (Intel Trusted Execution Technology)
(select models only; disabled by default).
(Continued)
Maintenance and Service Guide
5–17
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup
Select
To do this
System Configuration menu (continued)
Device Configurations (continued)
■ Enable/disable Dual Core CPU (select models only;
enabled by default).
■ Enable/Disable Unified Extensible Firmware Interface
(UEFI) mode (disabled by default).
■ Turn the Numlock state at boot on or off.
Built-In Device Options
■ Enable/disable the wireless button state (enabled
by default).
■ Enable/disable the embedded WLAN device (enabled
by default).
■ Enable/disable embedded WWAN device radio (select
models only; enabled by default).
■ Enable/disable embedded Bluetooth device radio (enabled
by default).
■ Enable/disable the Network Interface Controller (LAN)
(enabled by default).
■ Enable/disable LAN/WLAN switching (disabled by default).
■ Set the wake on LAN state. Options include the following:
❐ Disabled
❐ Boot to Network (set by default)
❐ Follow Boot Order
■ Enable/disable the fingerprint device (enabled by default).
■ Enable/disable a modem device (enabled by default).
■ Enable the ambient light sensor (enabled by default).
■ Enable/disable the Notebook MultiBay device (enabled
by default).
■ Enable/disable the integrated camera (select models only;
enabled by default).
■ Enable/disable optical disk drive (enabled by default).
■ Enable/disable internal microphones (enabled by default).
Port Options (all are enabled by default)
All port options are enabled by default.
✎
■ Enable/disable the Smart Card slot.
■ Enable/disable the ExpressCard slot.
■ Enable/disable the serial port.
■ Enable/disable the parallel port.
■ Enable/disable the flash media reader.
■ Enable/disable the USB port.
Disabling the USB port also disables MultiBay devices
and ExpressCard devices on the advanced
Ä
port replicator.
■ Enable/disable the 1394 port.
Set Security Level
Change, view, or hide security levels for all BIOS menu items
Restore the default security settings.
Restore Security Defaults
5–18
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Specifications
Computer specifications
Metric
U.S.
Dimensions
Depth
22.1 cm
32.8 cm
2.4 cm
8.7 in
Width
12.9 in
0.93 in
3.79 lbs
Height (front to back)
Weight
1.72 kg
Input power
Operating voltage
Operating current
Temperature
18.5 V dc @ 3.5 A - 65 W
3.5 A
Operating (not writing to optical disc)
Operating (writing to optical disc)
Nonoperating
0°C to 35°C
5°C to 35°C
-20°C to 60°C
32°F to 95°F
41°F to 95°F
-4°F to 140°F
Relative humidity
Operating
10% to 90%
5% to 95%
Nonoperating
Maximum altitude (unpressurized)
Operating
-15 m to 3,048 m
-15 m to 12,192 m
-50 ft to 10,000 ft
-50 ft to 40,000 ft
Nonoperating
Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
range of temperatures.
✎
Maintenance and Service Guide
6–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
13.3-in display specifications
Metric
U.S.
Dimensions
Height
17.8 cm
7.0 in
Width
28.4 cm
11.2 in
13.3 in
Diagonal
33.6 cm
Number of colors
Contrast ratio
Brightness
Pixel resolution
Pitch
Up to 16.8 million
250:1 (typical)
200 nits (typical)
0.279 × 0.279 mm
1366 × 768
RGB vertical stripe
LED
Format
Configuration
Backlight
Character display
Total power consumption
Viewing angle
80 × 25
4.0 W
40° horizontal, +120°/-40° vertical (typical)
6–2
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Hard drive specifications
500-GB*
320-GB*
250-GB*
Dimensions
Height
9.5 mm
70 mm
9.5 mm
70 mm
9.5 mm
70 mm
Width
Weight
101 g
101 g
101 g
Interface type
Transfer rate
Security
SATA
SATA
SATA
100 MB/sec
ATA security
100 MB/sec
ATA security
100 MB/sec
ATA security
Seek times (typical read, including setting)
Single track
1.5 ms
1.5 ms
2.0 ms
Average
12.0 ms
12.0 ms
12.0 ms
Maximum
22.0 ms
22.0 ms
22.0 ms
Logical blocks
Disc rotational speed
Operating temperature
625,142,448
7200 rpm
625,142,448
7200 rpm
488,397,168
7200 rpm
5°C to 55°C (41°F to 131°F)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less.
Actual drive specifications may differ slightly.
Certain restrictions and exclusions apply. Contact technical support for details.
✎
Maintenance and Service Guide
6–3
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Backup and recovery
Backup and recovery in Windows 7
Overview
To protect your information, use Windows Backup and Restore to back up individual files and folders, back up our
entire hard drive (select models only), create system repair discs (select models only), or create system restore
points. In case of system failure, you can use the backup files to restore the contents of your computer.
Windows Backup and Restore provides the following options:
■
■
■
■
■
■
■
■
Creating a system repair disc (select models only)
Backing up individual files and folders
Creating a system image (select models only)
Scheduling automatic backups (select models only)
Creating system restore points
Recovering individual files
Restoring the computer to a previous state
Recovering information using recovery tools
For detailed instructions, perform a search for these topics in Help and Support.
✎
✎
In case of system instability, HP recommends that you print the recovery procedures and save them for later use.
Backing up your information
Recovery after a system failure is as complete as your most current backup. You should create system repair discs
(select models only) and your initial backup immediately after software setup. As you add new software and data
files, you should continue to back up your system on a regular basis to maintain a reasonably current backup. The
system repair discs (select models only) are used to start up (boot) the computer and repair the operating system in
case of system instability or failure. Your initial and subsequent backups allow you to restore your data and settings
if a failure occurs.
You can back up your information to an optional external hard drive, a network drive, or discs.
Note the following when backing up:
■
■
■
Store personal files in the Documents library, and back it up regularly.
Back up templates that are stored in their associated programs.
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time-saver if you have to reset your preferences.
Maintenance and Service Guide
7–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Backup and recovery
To create a screen shot:
1. Display the screen you want to save.
2. Copy the screen image:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3. Open a word-processing document, and then select Edit > Paste.
The screen image is added to the document.
4. Save the document.
■
■
When backing up to discs, use any of the following types of discs (purchased separately): CD-R, CD-RW,
DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD+/-RW. The discs you use will depend on the type of
optical drive installed in your computer.
DVDs and DVDs with double-layer (DL) support store more information than CDs, so using them for
backup reduces the number of recovery discs required.
✎
When backing up to discs, number each disc before inserting it into the optical drive of the computer.
To create a backup using Backup and Restore, follow these steps:
Be sure that the computer is connected to AC power before you start the backup process.
✎
✎
The backup process may take over an hour, depending on file size and the speed of the computer.
1. Select Start > All Programs > Maintenance > Backup and Restore.
2. Follow the on-screen instructions to set up your backup, create a system image (select models only), or
create a system repair disc (select models only).
Windows includes the User Account Control feature to improve the security of your computer. You may be
prompted for your permission or password for tasks such as installing software, running utilities, or changing
Windows settings. Refer to Help and Support for more information.
✎
7–2
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Backup and recovery
Performing a recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
■
Windows recovery tools: You can use Windows Backup and Restore to recover information you have
previously backed up. You can also use Windows Startup Repair to fix problems that might prevent Windows
from starting correctly.
■
f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image. The image
includes the Windows operating system and software programs installed at the factory.
If you are unable to boot (start up) your computer and you cannot use the system repair discs you previously
created (select models only), you must purchase a Windows 7 operating system DVD to reboot the computer and
repair the operating system. For additional information, refer to the “Using a Windows 7 operating system DVD
(purchased separately)” section in this chapter.
✎
Using the Windows recovery tools
To recover information you previously backed up, follow these steps:
1. Select Start > All Programs > Maintenance > Backup and Restore.
2. Follow the on-screen instructions to recover your system settings, your computer (select models only), or
your files.
Windows includes the User Account Control feature to improve the security of your computer. You may be
prompted for your permission or password for tasks such as installing software, running utilities, or changing
Windows settings. Refer to Help and Support for more information.
✎
To recover your information using Startup Repair, follow these steps:
CAUTION: Using Startup Repair completely erases hard drive contents and reformats the hard drive. All files you have created
Ä
and any software installed on the computer are permanently removed. When reformatting is complete, the recovery process
restores the operating system, as well as the drivers, software, and utilities from the backup used for recovery.
1. If possible, back up all personal files.
2. If possible, check for the presence of the Windows partition and the HP Recovery partition.
To check for the Windows partition, select Start > Computer.
To check for the HP Recovery partition, select Start, right-click Computer, click Manage, and then click
Disk Management.
If the Windows partition and the HP Recovery partition are not listed, you must recover your operating
system and programs using the Windows 7 operating system DVD and the Driver Recovery disc (both
✎
purchased separately). For additional information, refer to the “Using a Windows 7 operating system
DVD (purchased separately)” section in this guide.
3. If the Windows partition and the HP Recovery partition are listed, restart the computer, and then press f8
before the Windows operating system loads.
4. Select Startup Repair.
5. Follow the on-screen instructions.
For additional information on recovering information using the Windows tools, perform a search for these topics
in Help and Support.
✎
Maintenance and Service Guide
7–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Backup and recovery
Using f11 recovery tools
CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files you have created and any
software installed on the computer are permanently removed. The f11 recovery tool reinstalls the operating system and
HP programs and drivers that were installed at the factory. Software not installed at the factory must be reinstalled.
To recover the original hard drive image using f11, follow these steps:
1. If possible, back up all personal files.
2. If possible, check for the presence of the HP Recovery partition: select Start, right-click Computer, click
Manage, and then click Disk Management.
If the HP Recovery partition is not listed, you must recover your operating system and programs using
the Windows 7 operating system DVD and the Driver Recovery disc (both purchased separately). For
✎
additional information, refer to the “Using a Windows 7 operating system DVD (purchased separately)”
section in this chapter.
3. If the HP Recovery partition is listed, restart the computer, and then press esc while the “Press the ESC key
for Startup Menu” message is displayed at the bottom of the screen.
4. Press f11 while the “Press <F11> for recovery” message is displayed on the screen.
5. Follow the on-screen instructions.
Using a Windows 7 operating system DVD (purchased separately)
If you are unable to boot (start up) your computer and you cannot use the system repair discs you previously
created (select models only), you must purchase a Windows 7 operating system DVD to reboot the computer and
repair the operating system. Make sure that your most recent backup (stored on discs or on an external drive) is
easily accessible. To order a Windows 7 operating system DVD, go to http://www.hp.com/support, select your country
or region, and follow the on-screen instructions. You can also order the DVD by calling technical support. For
contact information, refer to the Worldwide Telephone Numbers booklet included with the computer.
CAUTION: Using a Windows 7 operating system DVD completely erases hard drive contents and reformats the hard drive. All
Ä
files you have created and any software installed on the computer are permanently removed. When reformatting is complete, the
recovery process helps you restore the operating system, as well as drivers, software, and utilities.
To initiate recovery using a Windows 7 operating system DVD, follow these steps:
This process takes several minutes.
✎
1. If possible, back up all personal files.
2. Restart the computer, and then insert the Windows 7 operating system DVD into the optical drive before the
Windows operating system loads.
3. When prompted, press any keyboard key.
4. Follow the on-screen instructions.
5. Click Next.
6. Select Repair your computer.
7. Follow the on-screen instructions.
7–4
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Backup and recovery
Backup and recovery in Windows Vista
Overview
To protect your information, use the Backup and Restore Center to back up individual files and folders, back up
your entire hard drive (select models only), or create system restore points. In case of system failure, you can use
the backup files to restore the contents of your computer.
The Backup and Restore Center provides the following options:
■
■
■
■
■
■
■
Backing up individual files and folders
Backing up the entire hard drive (select models only)
Scheduling automatic backups (select models only)
Creating system restore points
Recovering individual files
Restoring the computer to a previous state
Recovering information using recovery tools
For detailed instructions, perform a search for these topics in Help and Support.
✎
In case of system instability, HP recommends that you print the recovery procedures and save them for later use.
Backing up your information
Recovery after a system failure is as complete as your most current backup. You should create your initial backup
immediately after software setup. As you add new software and data files, you should continue to back up your
system on a regular basis to maintain a reasonably current backup.
You can back up your information to an optional external hard drive, a network drive, or discs.
Note the following when backing up:
■
■
■
Store personal files in the Documents folder, and back it up regularly.
Back up templates that are stored in their associated programs.
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time-saver if you have to reset your preferences.
To create a screen shot:
a. Display the screen you want to save.
b. Copy the screen image:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c. Open a word-processing document, and then select Edit > Paste.
The screen image is added to the document.
d. Save the document.
Maintenance and Service Guide
7–5
Download from Www.Somanuals.com. All Manuals Search And Download.
Backup and recovery
■
When backing up to discs, use any of the following types of discs (purchased separately): CD-R, CD-RW,
DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD RW. The discs you use will depend on the type of
optical drive installed in your computer.
DVDs and DVDs with double-layer (DL) support store more information than CDs, so using them for
backup reduces the number of recovery discs required.
✎
■
When backing up to discs, number each disc before inserting it into the optical drive of the computer.
To create a backup using Backup and Restore Center, follow these steps:
Be sure that the computer is connected to AC power before you start the backup process.
The backup process may take over an hour, depending on file size and the speed of the computer.
✎
✎
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Follow the on-screen instructions to back up your entire computer (select models only) or your files.
Windows includes the User Account Control feature to improve the security of your computer. You may be
prompted for your permission or password for tasks such as installing software, running utilities, or changing
Windows settings. Refer to Help and Support for more information.
Performing a recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
■
Windows recovery tools: You can use the Backup and Restore Center to recover information you have
previously backed up. You can also use Windows Startup Repair to fix problems that might prevent Windows
from starting correctly.
■
f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image. The image
includes the Windows operating system and software programs installed at the factory.
If you are unable to boot (start up) your computer, you must purchase a Windows Vista operating system DVD to
reboot the computer and repair the operating system. For additional information, refer to the “Using a Windows
Vista operating system DVD (purchased separately)” section in this chapter.
✎
Using the Windows recovery tools
To recover information you previously backed up, follow these steps:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Follow the on-screen instructions to recover your entire computer (select models only) or your files.
Windows includes the User Account Control feature to improve the security of your computer. You may be
prompted for your permission or password for tasks such as installing software, running utilities, or changing
Windows settings. Refer to Help and Support for more information.
✎
7–6
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Backup and recovery
To recover your information using Startup Repair, follow these steps:
CAUTION: Using Startup Repair completely erases hard drive contents and reformats the hard drive. All files you have created
and any software installed on the computer are permanently removed. When reformatting is complete, the recovery process
restores the operating system, as well as the drivers, software, and utilities from the backup used for recovery.
Ä
1. If possible, back up all personal files.
2. If possible, check for the presence of the Windows partition and the HP Recovery partition. To find the
partitions, select Start > Computer.
If the Windows partition and the HP Recovery partition have been deleted, you must recover your operating
system and programs using the Windows Vista operating system DVD and the Driver Recovery disc (both
purchased separately). For additional information, refer to the “Using a Windows Vista operating system DVD
(purchased separately)” section in this chapter.
✎
3. Restart the computer, and then press f8 before the Windows operating system loads.
4. Select Repair your computer.
5. Follow the on-screen instructions.
For additional information on recovering information using the Windows tools, perform a search for these topics
in Help and Support.
✎
Using f11 recovery tools
CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files you have created and any
Ä
software installed on the computer are permanently removed. The f11 recovery tool reinstalls the operating system and
HP programs and drivers that were installed at the factory. Software not installed at the factory must be reinstalled.
If your computer includes a solid-state drive (SSD), you may not have a recovery partition. Recovery discs have
been included for computers that do not have a partition. Use these discs to recover your operating system and
software. To check for the presence of a recovery partition select Start > Computer. If the partition is present,
an HP Recovery drive is listed in the Hard Disk Drives section of the window.
✎
To recover the original hard drive image using f11, follow these steps:
1. If possible, back up all personal files.
2. If possible, check for the presence of the HP Recovery partition. To find the partition, select Start >
Computer.
If the HP Recovery partition has been deleted, you must recover your operating system and programs
using the Windows Vista operating system DVD and the Driver Recovery disc (both purchased
✎
separately). For additional information, refer to the “Using a Windows Vista operating system DVD
(purchased separately)” section in this chapter.
3. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message
is displayed at the bottom of the screen.
4. Press f11 while the “Press <F11> for recovery” message is displayed on the screen.
5. Follow the on-screen instructions.
Maintenance and Service Guide
7–7
Download from Www.Somanuals.com. All Manuals Search And Download.
Backup and recovery
Using a Windows Vista operating system DVD (purchased separately)
If you are unable to boot (start up) your computer, you must purchase a Windows Vista operating system DVD to
reboot the computer and repair the operating system. Make sure that your most recent backup (stored on discs or on
an external drive) is easily accessible. To order a Windows Vista operating system DVD, go to
http://www.hp.com/support, select your country or region, and follow the on-screen instructions. You can also order the
DVD by calling technical support. For contact information, refer to the Worldwide Telephone Numbers booklet
included with the computer.
CAUTION: Using a Windows Vista operating system DVD completely erases hard drive contents and reformats the hard drive.
Ä
All files you have created and any software installed on the computer are permanently removed. When reformatting is complete,
the recovery process helps you restore the operating system, as well as drivers, software, and utilities.
To initiate recovery using a Windows Vista operating system DVD, follow these steps:
This process takes several minutes.
✎
1. If possible, back up all personal files.
2. Restart the computer, and then insert the Windows Vista operating system DVD into the optical drive before
the Windows operating system loads.
3. When prompted, press any keyboard key.
4. Follow the on-screen instructions.
5. Click Next.
6. Select Repair your computer.
7. Follow the on-screen instructions.
7–8
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Backup and recovery
Backup and recovery in Windows XP
Overview
To protect your information, use the Windows Backup utility (select models only) to back up files and folders or
create recovery points. In case of system failure, you can use the backup files to restore your computer.
Windows provides the following options:
■
■
■
■
■
Backing up individual files and folders
Backing up all files and folders
Scheduling automatic backups
Creating recovery points
Recovering information
For detailed instructions, perform a search for these topics in Help and Support.
✎
In case of system instability, HP recommends that you print the recovery procedures and save them for later use.
Backing up your information
Recovery after a system failure is as complete as your most current backup. You should create your initial backup
immediately after software setup. As you add new software and data files, you should continue to back up your
system on a regular basis to maintain a reasonably current backup.
You can back up individual files or folders to an optional external hard drive or to a network drive.
Note the following when backing up:
■
■
■
Store personal files in the My Documents folder, and back it up periodically.
Back up templates stored in their associated programs.
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
a. Display the screen you want to save.
b. Copy the screen image:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c. Open a word-processing document, and then select Edit > Paste.
The screen image is added to the document.
d. Save the document.
To create a backup using the Windows Backup utility (select models only), follow these steps:
Be sure that the computer is connected to AC power before you start the backup process.
The backup process may take over an hour, depending on file size and the speed of the computer.
✎
1. Select Start > All Programs > Accessories > System Tools > Backup.
2. Follow the on-screen instructions.
Maintenance and Service Guide
7–9
Download from Www.Somanuals.com. All Manuals Search And Download.
Backup and recovery
Performing a recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
■
Windows recovery tools (select models only): You can use the Windows Backup utility to recover information
you have previously backed up.
■
Operating System and Driver Recovery discs (included with your computer): You can use the discs to recover
your operating system and programs installed at the factory.
Recovering your information
To recover information you previously backed up, follow these steps:
1. If possible, back up all personal files.
2. Select Start > All Programs > Accessories > System Tools > Backup.
The Backup or Restore Wizard opens.
3. Click Restore files and settings, and then click Next.
4. Follow the on-screen instructions.
For additional information on initiating a recovery in Windows, perform a search for this topic in
Help and Support.
✎
Recovering the operating system and programs
CAUTION: The recovery process reformats and completely erases the hard drive. All files you have created and any software
Ä
installed on the computer are permanently removed. The recovery process reinstalls the original operating system, software, and
drivers. Software, drivers, and updates not installed by HP must be manually reinstalled.
To recover your operating system and programs, follow these steps:
1. If possible, back up all personal files.
2. Insert the Operating System disc into the optical drive.
3. Shut down the computer.
4. Turn on the computer.
5. Follow the on-screen instructions to install the operating system.
6. After the operating system is installed, remove the Operating System disc and insert the
Driver Recovery disc.
7. Follow the on-screen instructions to install the drivers and programs.
7–10
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Connector pin assignments
Audio-in (microphone)
Pin
1
Signal
Audio signal in
Audio signal in
Ground
2
3
Audio-out (headphone)
Pin
1
Signal
Audio out, left channel
Audio out, right channel
Ground
2
3
Maintenance and Service Guide
8–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connector pin assignments
External monitor
Pin
1
Signal
Red analog
Green analog
Blue analog
Not connected
Ground
2
3
4
5
6
Ground analog
Ground analog
Ground analog
+5 VDC
7
8
9
10
11
12
13
14
15
Ground
Monitor detect
DDC 2B data
Horizontal sync
Vertical sync
DDC 2B clock
8–2
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Power cord set requirements
The wide-range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC,
or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the country or region
where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or region where
the computer is used.
Requirements for all countries and regions
The following requirements are applicable to all countries and regions:
■
■
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the
country or region where the power cord set will be used.
■
■
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating of 125 or
250 V AC, as required by the power system of each country or region.
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet C13
connector for mating with the appliance inlet on the back of the computer.
Maintenance and Service Guide
9–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Power cord set requirements
Requirements for specific countries and regions
Country/region
Australia
Accredited agency
EANSW
OVE
Applicable note number
1
1
1
2
1
1
1
1
1
3
1
1
5
4
1
1
4
1
2
Austria
Belgium
CEBC
CSA
Canada
Denmark
DEMKO
FIMKO
UTE
Finland
France
Germany
VDE
Italy
IMQ
Japan
METI
The Netherlands
Norway
KEMA
NEMKO
CCC
The People's Republic of China
South Korea
Sweden
EK
SEMKO
SEV
Switzerland
Taiwan
BSMI
The United Kingdom
The United States
BSI
UL
1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type
with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the Japanese
Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug must be a
two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4. The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
5. The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
9–2
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general household waste.
Follow the local laws and regulations in your area for computer battery disposal.
Display
WARNING: The backlight contains mercury. Caution must be exercised when removing and handling the backlight to avoid
Å
Ä
damaging this component and causing exposure to the mercury.
CAUTION: The procedures in this chapter can result in damage to display components. The only components intended for
recycling purposes are the liquid crystal display (LCD) panel and the backlight. When you remove these components, handle
them carefully.
Materials Disposal. This HP product contains mercury in the backlight in the display assembly that might
require special handling at end-of-life. Disposal of mercury may be regulated because of environmental
considerations. For disposal or recycling information, contact your local authorities, or see the Electronic
Industries Alliance (EIA) Web site at http://www.eiae.org.
✎
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight 1 and the liquid crystal display (LCD) panel 2.
The procedures provided in this chapter are general disassembly instructions. Specific details, such as screw
sizes, quantities, and locations, and component shapes and sizes, can vary from one computer model to another.
✎
Maintenance and Service Guide
10–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Recycling
Perform the following steps to disassemble the display assembly:
1. Remove all screw covers 1 and screws 2 that secure the display bezel to the display assembly.
2. Lift up and out on the left and right inside edges 1 and the top and bottom inside edges 2 of the display bezel
until the bezel disengages from the display assembly.
3. Remove the display bezel 3.
10–2
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Recycling
4. Disconnect all display panel cables 1 from the display inverter and remove the inverter 2.
5. Remove all screws 1 that secure the display panel assembly to the display enclosure.
6. Remove the display panel assembly 2 from the display enclosure.
7. Turn the display panel assembly upside down.
8. Remove all screws that secure the display panel frame to the display panel.
Maintenance and Service Guide
10–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Recycling
9. Use a sharp-edged tool to cut the tape 1 that secures the sides of the display panel to the display panel frame.
10. Remove the display panel frame 2 from the display panel.
11. Remove the screws 1 that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover 2 and swing it outward.
13. Remove the backlight cover.
14. Turn the display panel right-side up.
15. Remove the backlight cables 1 from the clip 2 in the display panel.
10–4
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Recycling
16. Turn the display panel upside down.
17. Remove the backlight frame from the display panel.
WARNING: The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging
this component and causing exposure to the mercury.
Å
18. Remove the backlight from the backlight frame.
Maintenance and Service Guide
10–5
Download from Www.Somanuals.com. All Manuals Search And Download.
Recycling
19. Disconnect the display cable 1 from the LCD panel.
20. Remove the screws 2 that secure the LCD panel to the display rear panel.
21. Release the LCD panel 3 from the display rear panel.
22. Release the tape 4 that secures the LCD panel to the display rear panel.
23. Remove the LCD panel.
24. Recycle the LCD panel and backlight.
10–6
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
buttons
A
accessory cover
power 2–4
QuickLook 2–4
QuickWeb 2–4
TouchPad 2–7
wireless 2–4
illustrated 3–9
removal 4–9
antennas
illustrated 3–7
locations 2–3
C
Cable Kit
components 3–6
cables, service considerations 4–1
caps lock light 2–6
chipset, product description 1–1
combo headphone microphone jack, location 2–8
components
audio, product description 1–1
audio-in jack
connector pinout 8–1
location 2–8
audio-out jack
connector pinout 8–1
location 2–8
bottom 2–10
buttons 2–4
fingerprint reader 2–4
B
backing up files 8–5
front 2–8
keys 2–5
left-side 2–9
battery
lights 2–6
removal 4–7
pointing device 2–7
right-side 2–8
battery bay 2–10
computer feet
battery eject arm
locations 4–6
removal 4–41
spare part number 4–6
Computer Setup
spare part number 4–41
battery light 2–9
computer specifications 6–1
connector pinout
battery release latch 2–10
BIOS administrator password 5–15
Bluetooth module
removal 4–12
Bluetooth module cable
illustrated 3–6
audio-in jack 8–1
audio-out jack 8–1
external monitor port 8–2
headphone jack 8–1
microphone jack 8–1
monitor port 8–2
removal 4–32
bottom components 2–10
button board
network jack 8–3
RJ-45 jack 8–3
removal 4–26
Maintenance and Service Guide
Index–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
USB port 8–4
connectors, service considerations 4–1
creating a backup 8–5
F
f11 recovery 8–7
fan
removal 4–36
feet
D
locations 4–6
Disk Sanitizer 5–15
display assembly
spare part number 4–6
front components 2–8
function keys 2–5
removal 4–43
display bezel
removal 4–44
Display Cable Kit
illustrated 3–7
display components
G
graphics, product description 1–1
grounding equipment and methods 4–2
H
hard drive
precautions 4–2
product description 1–1
removal 4–9
recycling 10–1
specifications 6–3
hard drive bay 2–10
hard drive recovery 8–7
headphone jack
spare part numbers 3–7
display enclosure
display hinge
removal 4–46
display inverter, removal 10–3
display panel cable
connector pinout 8–1
location 2–8
heat sink
removal 4–36
spare part number 4–36
hinge
illustrated 3–7
removal 4–47
removal 4–46
spare part numbers 4–47
display panel, product description 1–1
display switch, location 2–2
DisplayPort, location 2–9
drive light 2–8
HP SpareKey Enrollment 5–15
J
jacks
DriveLock password 5–15
DriveLock, automatic 5–15
audio-in 2–8
audio-out 2–8
combo headphone microphone 2–8
headphone 2–8
microphone 2–8
network 2–9
E
electrostatic discharge 4–2
equipment guidelines 4–4
RJ-45 2–9
K
Ethernet, product description 1–2
external media card, product description 1–2
external monitor port
connector pinout 8–2
location 2–9
key components 2–5
keyboard
product description 1–2
removal 4–23
Index–2
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
keys
esc 2–5
passwords 5–15
plastic parts 4–1
fn 2–5
Plastics Kit
function 2–5
components 3–9
numeric keypad 2–5
Windows applications 2–5
Windows logo 2–5
contents 3–9
pointing device
components 2–7
illustrated 2–7
product description 1–2
port options 5–12
ports
L
left-side components 2–9
light components 2–6
lights
DisplayPort 2–9
external monitor port 2–9
monitor port 2–9
powered USB 2–9
product description 1–2
battery 2–9
caps lock 2–6
drive 2–8
power 2–6
QuickLook 2–6
QuickWeb 2–6
wireless 2–6
power button 2–4
power button board
removal 4–31
M
power button board cable, illustrated 3–6
power connector 2–9
power cord
set requirements 9–1
power light 2–6
power requirements, product description 1–2
powered USB port
location 2–9
mass storage device
removal 4–9
memory module
removal 4–21
memory, product description 1–1
microphone
illustrated 3–7
locations 2–2
product description 1–1
removal 4–49
processor, product description 1–1
product description
audio 1–1
spare part number 4–49
microphone jack
connector pinout 8–1
location 2–8
model name 4–5
chipset 1–1
display panel 1–1
Ethernet 1–2
external media card 1–2
graphics 1–1
monitor port
hard drive 1–1
connector pinout 8–2
location 2–9
keyboard 1–2
memory 1–1
microphone 1–1
N
operating system 1–3
pointing device 1–2
ports 1–2
power requirements 1–2
processor 1–1
security 1–2
serviceability 1–4
webcam 1–1
network jack
connector pinout 8–3
location 2–9
numeric keypad keys 2–5
O
operating system, product description 1–3
P
wireless 1–2
packing guidelines 4–3
Maintenance and Service Guide
Index–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
solid-state drive
removal 4–9
speaker assembly
removal 4–39
speakers 2–8
Q
QuickLook button 2–4
QuickLook light 2–6
QuickWeb button 2–4
QuickWeb light 2–6
R
specifications
recovering information 8–6
recovery partition 8–7
recovery, system 8–1
recycling
computer 6–1
display assembly 6–2
hard drive 6–3
system board
battery 10–1
removal 4–33
display components 10–1
removal/replacement
preliminaries 4–1
system IDs 5–15
procedures 4–5
system recovery 8–1
restoring the hard drive 8–5
right-side components 2–8
RJ-45 jack
connector pinout 8–3
location 2–9
RTC battery
T
tools required 4–1
top cover
removal 4–28
TouchPad 2–7
TouchPad buttons 2–7
TouchPad scroll zone 2–7
removal 4–20
U
Universal Serial Bus (USB) port
connector pinout 8–4
S
SD Card Reader 2–8
USB board
removal 4–40
USB board cable, illustrated 3–6
SD Card Reader slot bezel, illustrated 3–9
security cable slot 2–8
allow reset of HP ProtectTools security keys 5–15
always prompt for HP SpareKey enrollment 5–15
Automatic DriveLock 5–15
change password 5–15
V
W
warranty period 4–5
webcam
Disk Sanitizer 5–15
DriveLock 5–15
HP SpareKey 5–15
HP SpareKey enrollment 5–15
password policy 5–15
set up BIOS administrator password 5–15
System IDs 5–15
user management 5–15
location 2–2
product description 1–1
webcam cable, illustrated 3–7
webcam module
illustrated 3–7
removal 4–45
Windows applications key 2–5
Windows logo key 2–5
Windows Vista operating system DVD 8–6
wireless antennas
security, product description 1–2
service considerations 4–1
serviceability, product description 1–4
SIM slot 2–10
SIM, removal 4–8
Index–4
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
|