HP Compaq 2210b Notebook PC
Maintenance and Service Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a
hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact
the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the AC
adapter comply with the user-accessible surface temperature limits defined by the International Standard
for Safety of Information Technology Equipment (IEC 60950).
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Safety warning notice
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
2 External component identification
3 Illustrated parts catalog
4 Removal and replacement procedures
Electrostatic discharge damage .................................................................. 31
v
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Computer Setup
6 Specifications
7 Screw listing
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Backup and recovery
9 Connector pin assignments
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Recycling
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Product description
Category
Description
Product Name
Processors
HP Compaq 2210b Notebook PC
Intel® Core™ 2 Duo processors:
T7800 2.6-GHz processor, 4-MB L2 cache, 800-MHz front side bus (FSB)
T7700 2.4-GHz processor, 4-MB L2 cache, 800-MHz FSB
T7500 2.2-GHz processor, 4-MB L2 cache, 800-MHz FSB
T7300 2.0-GHz processor, 4-MB L2 cache, 800-MHz FSB
T7100 1.8-GHz processor, 2-MB L2 cache, 800-MHz FSB
Intel Celeron® M processors:
Celeron M 540 1.86-Ghz processor, 2-MB L2 cache, 533-MHz FSB
Celeron M 530 1.73-Ghz processor, 2-MB L2 cache, 533-MHz FSB
Northbridge: Intel GM965 with up to 800-Mhz FSB
Southbridge: Intel ICH8M
Chipset
Graphics
Panel
Intel Unified Memory Architecture (UMA) graphics subsystem integrated with shared system
memory (dynamically allocated)
12.1-inch WXGA panel (1280 × 800)
All display assemblies include 2 wireless local area network (WLAN) antennae
2 customer-accessible/upgradable memory module slots
Supports dual-channel memory
Memory
Supports up to 4 GB of system RAM
PC2-5300, 667-MHz, DDR2
Supports the following configurations:
●
●
●
●
●
●
4096-MB total system memory (2048 × 2, dual-channel)
3072-MB total system memory (2048 + 1024)
2560-MB total system memory (2048 + 512)
2048-MB total system memory (1024 × 2, dual-channel)
2048-MB total system memory (2048 × 1)
1536-MB total system memory (1024 + 512)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Category
Description
●
●
●
1024-MB total system memory (512 × 2, dual-channel)
1024-MB total system memory (1024 × 1)
512-MB total system memory (512 × 1)
Hard drives
Supports 9.5-mm, 2.5-inch hard drives
Customer-accessible
Serial ATA
HP 3D DriveGuard
Supports the following drives:
●
●
●
●
200-GB, 4200-rpm
160-GB, 5400-rpm
120-GB, 5400-rpm
80-GB, 5400-rpm
Optical drives
Fixed (removal of 1 screw required)
Customer-accessible
Parallel ATA
12.7-mm tray load
Supports no-optical-drive option
Supports the following drives:
●
●
DVD/CD-RW Combo Drive
DVD-ROM Drive
Diskette drive
Microphone
Audio
Supports external USB diskette drive only
Integrated mono microphone
Azalia audio
2 speakers
Modem
Ethernet
56K V.92 1.5-inch data/fax modem with digital line guard
Modem cable included
Intel Broadcom 5787 10/100/1000 network interface card (NIC)
S4/S5 wake on LAN: AC
NIC power-down technology
Wireless
Integrated WLAN options by way of wireless module:
2 wireless antennae built into display assembly
Support for no-WLAN option
2
Chapter 1 Product description
Download from Www.Somanuals.com. All Manuals Search And Download.
Category
Description
Support for the following WLAN formats:
●
●
●
●
●
Intel 802.11a/b/g/n
Broadcom 802.11a/b/g
Intel 802.11a/b/g
Broadcom 802.11b/g
Intel 802.11b/g
Integrated personal area network (PAN) options by way of Bluetooth®
module:
Support for no-WPAN option
Broadcom Bluetooth
External media card
Ports
One Type I/II PC Card slot, supporting 16-bit and 32-bit (Cardbus) PC Card modules
Media Card Reader supporting MMC and SD digital cards
Audio-in (mono microphone)
Audio-out (stereo headphone)
S-Video-out
RJ-11 (modem)
RJ-45 (Ethernet, includes link and activity lights)
USB (3)
VGA (Dsub 15-pin) supporting 1600 × 1200 external resolution at 75-GHz (hot plug/unplug
with auto-detect)
Multi-pin AC power
Keyboard/pointing devices
Spill-resistant 12.3-inch keyboard
TouchPad with 2 TouchPad buttons
Supports 1-way scroll
Taps enabled as default
Windows Vista® Hardware Start Button
Power requirements
65-W AC adapter with localized and pointing stick cable plug support (3-wire plug with
ground pin, supports 3-pin DC connector)
8-cell, 2.55-Ah (73-Wh) Li-ion battery
4-cell, 2.25-Ah (37-Wh) Li-ion battery
Security cable slot
Security
Integrated fingerprint reader
Preinstalled:
Operating system
Windows Vista® Business 32
Windows Home Basic 32
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Category
Description
Windows® XP Professional
FreeDOS (India and Thailand)
FreeDOS (Thailand)
Restore Media:
Windows Vista Business 32
Windows Vista Home Basic 32
Windows XP Professional
DRDVD XP
DRDVD Vista
Serviceability
End-user replaceable parts:
AC adapter
Battery (system)
Hard drive
Memory module
Optical drive
WLAN module
4
Chapter 1 Product description
Download from Www.Somanuals.com. All Manuals Search And Download.
2
External component identification
Display components
Component
Function
Wireless antennae (2)*
Send and receive wireless signals to communicate with
WLANs.
*The antennae are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the
antennae free from obstructions.
To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies to your
country or region. These notices are located in Help and Support.
Display components
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Top components
Pointing devices
Item
(1)
Component
Function
TouchPad
Moves the pointer and selects or activates items on the
screen.
(2)
(3)
(4)
Left TouchPad button
Right TouchPad button
TouchPad scroll zone
Functions like the left button on an external mouse.
Functions like the right button on an external mouse.
Scrolls up or down.
NOTE: This table describes factory settings. View or change pointing device preferences as follows:
●
●
In Windows Vista, select Start > Control Panel > Hardware and Sound > Mouse.
In Windows XP, select Start > Control Panel > Printers and Other Hardware > Mouse.
6
Chapter 2 External component identification
Download from Www.Somanuals.com. All Manuals Search And Download.
Buttons and fingerprint reader
Item
(1)
Component
Function
Power button
●
●
●
When the computer is off, press the button to turn on
the computer.
When the computer is on, press the button to shut down
the computer.
When the computer is in the Sleep state (Windows
Vista) or in Standby (Windows XP), press the button
briefly to exit the Sleep state or Standby.
●
When the computer is in Hibernation, press the button
briefly to exit Hibernation.
If the computer has stopped responding and Windows®
shutdown procedures are ineffective, press and hold the
power button for at least 5 seconds to turn off the computer.
To learn more about power settings, follow these steps:
●
In Windows Vista, select Start > Control Panel >
System and Maintenance > Power Options.
●
In Windows XP, select Start > Control Panel >
System and Maintenance > Power Options.
(2)
Info button
Launches Info Center, which enables you to open various
software solutions.
(3)
(4)
Presentation button
Wireless button
Starts the presentation feature.
Turns the wireless feature on or off, but does not establish a
wireless connection.
NOTE: A wireless network must be set up in order to
establish a wireless connection.
(5)
Volume mute button
Mutes and restores speaker sound.
Top components
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
(6)
Component
Function
Volume scroll zone
Adjusts speaker volume. Slide your finger to the left to
decrease volume and to the right to increase volume.
(7)
HP Fingerprint Sensor (fingerprint reader)
Allows a fingerprint logon to Windows, instead of a
password logon.
Keys
Item
(1)
Component
Function
esc key
Displays system information when pressed in combination
with the fn key.
(2)
fn key
Executes frequently used system functions when pressed in
combination with a function key or the esc key.
(3)
(4)
(5)
(6)
Windows logo key
Displays the Windows Start menu.
Windows applications key
Embedded numeric keypad keys
Function keys
Displays a shortcut menu for items beneath the pointer.
Can be used like the keys on an external numeric keypad.
Execute frequently used system functions when pressed in
combination with the fn key.
8
Chapter 2 External component identification
Download from Www.Somanuals.com. All Manuals Search And Download.
Lights
Item
(1)
Component
Function
Wireless lights (2)†
●
On: An integrated wireless device, such as a wireless
local area network (WLAN) device, the HP Broadband
Wireless Module, and/or a Bluetooth® device, is on.
●
●
●
Off: All wireless devices are off.
On: The computer is on.
(2)
(3)
Power lights (2)*
Blinking: The computer is in the Sleep state (Windows
Vista) or in Standby (Windows XP).
●
Blinking rapidly: An AC adapter with a higher power
rating should be connected.
●
●
●
●
Off: The computer is off or in Hibernation.
Amber: A battery is charging.
Battery light
Green: A battery is close to full charge capacity.
Blinking amber: A battery that is the only available
power source has reached a low battery level. When
the battery reaches a critical battery level, the battery
light begins blinking rapidly.
●
Off: If the computer is plugged into an external power
source, the light turns off when all batteries in the
computer are fully charged. If the computer is not
plugged into an external power source, the light stays
off until the battery reaches a low battery level.
(4)
Drive light
●
●
Blinking green: The hard drive or optical drive is being
accessed.
Amber: HP 3D DriveGuard has temporarily parked the
internal hard drive.
Top components
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
(5)
Component
Function
Volume mute light
●
●
Off: Computer sound is on.
On: Computer sound is off.
(6)
(7)
Volume down light
Volume up light
Blinking: The volume scroll zone is being used to decrease
speaker volume.
Blinking: The volume scroll zone is being used to increase
speaker volume.
*The 2 power lights display the same information. The light on the power button is visible only when the computer is open. The
power light on the front of the computer is visible whether the computer is open or closed.
†The 2 wireless lights display the same information. The light on the wireless button is visible only when the computer is open.
The wireless light on the front of the computer is visible whether the computer is open or closed.
10 Chapter 2 External component identification
Download from Www.Somanuals.com. All Manuals Search And Download.
Front components
Item
(1)
Component
Function
Wireless light
●
On: An integrated wireless device, such as a WLAN
device, the HP Broadband Wireless Module, and/or a
Bluetooth device, is turned on.
●
●
●
Off: All wireless devices are turned off.
On: The computer is on.
(2)
(3)
Power light
Blinking: The computer is in the Sleep state (Windows
Vista) or in Standby (Windows XP).
●
Blinking rapidly: An AC adapter with a higher power
rating should be connected.
●
●
●
●
Off: The computer is off or in Hibernation.
Amber: A battery is charging.
Battery light
Green: A battery is close to full charge capacity.
Blinking amber: A battery that is the only available
power source has reached a low battery level. When
the battery reaches a critical battery level, the battery
light begins blinking rapidly.
●
Off: If the computer is plugged into an external power
source, the light turns off when all batteries in the
computer are fully charged. If the computer is not
plugged into an external power source, the light stays
off until the battery reaches a low battery level.
(4)
Drive light
●
●
Blinking green: The hard drive or optical drive is being
accessed.
Amber (select models only): HP 3D DriveGuard has
temporarily parked the hard drive.
(5)
(6)
Speakers (2)
Produce sound.
Audio-out (headphone) jack
Produces sound when connected to optional powered stereo
speakers, headphones, ear buds, a headset, or television
audio.
(7)
Audio-in (microphone) jack
Connects an optional computer headset microphone, stereo
array microphone, or monaural microphone.
Front components 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Left-side components
Item
Component
Function
(1)
(2)
(3)
Power connector
USB ports (2)
Connects an AC adapter.
Connect optional USB devices.
Connects a network cable.
RJ-45 (network) jack
NOTE: The RJ-45 (network) jack provides Gigabit Ethernet
functionality.
(4)
(5)
RJ-11 (modem) jack
Optical drive
Connects a modem cable.
Reads optical discs and, on select models, also writes to
optical discs.
(6)
Optical drive light
On: The optical drive is being accessed.
12 Chapter 2 External component identification
Download from Www.Somanuals.com. All Manuals Search And Download.
Right-side components
Item
Component
Function
(1)
(2)
ExpressCard slot (select models only)
Media Card Reader
Supports optional ExpressCard/54 cards.
Supports the following optional digital card formats:
MultiMedia Card (MMC) and Secure Digital (SD) Memory
Card.
(3)
(4)
USB port (select models only)
S-Video-out jack
Connects an optional USB device.
Connects an optional S-Video device such as a television,
VCR, camcorder, overhead projector, or video capture
card.
(5)
(6)
(7)
Internal microphone
External monitor port
Vent
Records sound.
Connects an external VGA monitor or projector.
Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(8)
Security cable slot
Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a
deterrent, but it may not prevent the computer from being
mishandled or stolen.
Right-side components 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Bottom components
Item
Component
Function
(1)
(2)
Hard drive bay
Vents (5)
Holds the hard drive.
Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(3)
(4)
(5)
Memory module compartment
Battery bay
Contains a memory module slot.
Holds the battery.
WLAN module compartment
Contains a WLAN module slot.
CAUTION: To prevent an unresponsive system, use only
a wireless module authorized for use in the computer by the
governmental agency that regulates wireless devices in your
country or region. If you install the module and then receive
a warning message, remove the module to restore computer
functionality, and then contact technical support through
Help and Support.
(6)
Battery release latch
Releases the battery from the battery bay.
14 Chapter 2 External component identification
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
(1)
Description
Spare part
number
12.1-inch, WXGA display assembly (includes 2 WLAN antenna transceivers and
cables)
454004-001
Display internal components
Display bezel (includes nameplate)
Display inverter
455400-001
454009-001
454011-001
454398-001
454006-001
Display hinges
Display enclosure (includes logo)
Switch cover (includes LED board and cable)
Keyboards (include keyboard cable)
For use in Japan
(2)
(3)
454017-291
454017-AD1
454017-AB1
454017-281
454017-001
453994-001
449137-001
For use in South Korea
For use in Taiwan
For use in Thailand
For use in the United States
(4)
(5)
(6)
Top cover (includes TouchPad and cable, and fingerprint reader board and cable)
RTC battery
Microphone (included in the Cable Kit, spare part number 454008-001. See Cable Kit on page 21 for more Cable
Kit information.)
(7)
(8)
Speaker assembly
Bluetooth module
457906-001
398393-002
NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The
Bluetooth module cable is included in the Cables Kit, spare part number 454008-001. See
Cable Kit on page 21 for more Cable Kit information.
ExpressCard slot bezel
454010-001
(9a)
(9b)
(9c)
(9d)
(10)
(11)
(12)
WLAN module compartment cover
Memory module compartment cover
Hard drive cover
Front LED board (includes front LED board cable)
System board (includes replacement thermal material)
Modem modules
453996-001
453991-001
NOTE: The modem module spare part kits do not include a modem module cable. The modem module cable is included
in the Cables Kit, spare part number 454008-001. See Cable Kit on page 21 for more Cable Kit information.
For use in all countries and regions except Japan and Asia Pacific countries and regions
For use only in Japan and Asia Pacific countries and regions
ExpressCard assembly
451403-001
449139-001
457907-001
(13)
Computer major components 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
(14)
Description
Spare part
number
Processors (include replacement thermal material)
Intel Core 2 Duo processors (4-MB L2 cache, 800-MHz FSB):
●
●
●
●
●
T7800 2.6-GHz processor
454016-001
446894-001
454015-001
446892-001
446891-001
T7700 2.4-GHz processor
T7500 2.2-GHz processor
T7300 2.0-GHz processor
T7100 1.8-GHz processor (1-MB L2 cache)
Intel Celeron M processors (1-MB L2 cache, 533-MHz FSB):
●
●
540 1.86-GHz processor
530 1.73-GHz processor
454600-001
454599-001
453998-001
445853-001
453999-001
(15)
Heat sink (includes replacement thermal material)
Thermal Material Kit
(16)
(17)
Fan
Optical drives (include optical drive bezel and bracket)
DVD/CD-RW Combo Drive
DVD-ROM Drive
454333-001
454334-001
454000-001
453993-001
Optical Drive Bezel/Bracket Kit (not illustrated)
Base enclosure (includes rubber feet)
Batteries
(18)
(19)
8-cell, 73-WH
454002-001
454001-001
4-cell, 37-WH
(20)
WLAN modules
Intel 802.11a/b/g/n WLAN modules:
●
●
For use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India,
Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay,
the United States, Venezuela, and Vietnam
441086-001
441086-002
For use in Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece,
Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania,
Luxembourg, Malta, Monaco, the Netherlands, Norway, Oman, the Philippines, Poland,
Portugal, Qatar, Romania, Russia, Serbia and Montenegro, Singapore, Slovakia,
Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the
United Kingdom, and Uzbekistan
●
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South 441086-003
Korea
For use in Japan
441086-291
Broadcom 802.11a/b/g WLAN modules:
18 Chapter 3 Illustrated parts catalog
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
Spare part
number
●
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
441075-002
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia
and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina
Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus,
the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor,
Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland,
France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece,
Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras,
Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica,
Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia,
Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the
Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria,
Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the
Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda,
Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia and
Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon
Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia,
St. Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan,
Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu,
Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan,
Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
●
For use in Japan
441075-291
448674-001
Intel 802.11a/b/g WLAN modules:
●
For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India,
Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United
States, Uruguay, Venezuela, and Vietnam
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the
Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece,
Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania,
Luxembourg, Malta, Monaco, the Netherlands, Norway, Oman, the Philippines, Poland,
Portugal, Qatar, Romania, Russia, Serbia and Montenegro, Singapore, Slovakia,
Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the
United Kingdom, and Uzbekistan
448674-002
●
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South 448674-003
Korea
For use in Japan
448674-291
Broadcom 802.11b/g WLAN modules:
●
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua & Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia
& Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina
Faso, Burundi, Cambodia, Cameroon, Cape Verde, the Central African Republic, Chad,
Chile, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic,
Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El
Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French
Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada,
Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong,
Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan,
Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia,
441090-002
Computer major components 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
Spare part
number
Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the
Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria,
Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, the People's Republic
of China, Peru, the Philippines, Poland, Portugal, Qatar, the Republic of Moldova,
Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia,
Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia,
Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St.
Kitts & Nevis, St. Lucia, St. Vincent & Grenada, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad & Tobago,
Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the
United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire,
Zambia, and Zimbabwe
●
For use in Japan
441090-291
448675-004
Intel 802.11b/g WLAN module for use in Thailand
Memory modules (PC2-5300, 667-MHz, DDR2)
2048-MB
(21)
(22)
417506-001
414046-001
414045-001
1024-MB
512-MB
Hard drives (include hard drive bracket)
200-GB, 4200-rpm
454338-001
454337-001
454336-001
454335-001
454008-001
160-GB, 5400-rpm
120-GB, 5400-rpm
80-GB, 5400-rpm
Cable Kit (not illustrated
20 Chapter 3 Illustrated parts catalog
Download from Www.Somanuals.com. All Manuals Search And Download.
Plastics Kit
Item Description
Spare part number
Plastics Kit:
454010-001
(1)
(2)
(3)
(4)
ExpressCard slot bezel
WLAN module compartment cover (includes one captive screw, secured by a C-clip)
Memory module compartment cover (includes one captive screw, secured by a C-clip)
Hard drive cover (includes 2 captive screws, secured by C-clips)
22 Chapter 3 Illustrated parts catalog
Download from Www.Somanuals.com. All Manuals Search And Download.
Item Description
Spare part number
(5)
(6)
Computer feet (4)
Base enclosure screw covers (4 covers, 2 sizes)
Mass storage devices
Item Description
Spare part number
(1)
Hard drives (include bracket )
200-GB, 4200-rpm
454338-001
454337-001
454336-001
454335-001
160-GB, 5400-rpm
120-GB, 5400-rpm
80-GB, 5400-rpm
(2)
Optical drives (include bezel)
DVD/CD-RW Combo Drive
DVD-ROM Drive
454333-001
454334-001
Mass storage devices 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Miscellaneous parts
Description
Spare part number
65-W AC adapter
Power cords:
391172-001
For use in Australia
For use in Japan
246959-011
246959-291
246959-001
454014-001
For use the United States
Screw Kit
●
●
●
●
●
●
●
●
●
●
●
●
●
Phillips PM3.0×4.0 screw
Phillips PM2.5×12.0 captive screw
Phillips PM2.5×7.0 captive screw
Phillips PM2.5×7.0 screw
Phillips PM2.5×6.0 screw
Phillips PM2.5×5.0 screw
Phillips PM2.5×4.0 screw
Phillips PM2.0×6.0 screw
Phillips PM2.0×6.0 shoulder screw
Phillips PM2.0×5.0 captive screw
Phillips PM2.0×3.0 screw
Torx T8M2.5×6.0 screw
Torx T8M2.5×5.0 screw
24 Chapter 3 Illustrated parts catalog
Download from Www.Somanuals.com. All Manuals Search And Download.
Sequential part number listing
Spare part
number
Description
246959-001
246959-011
246959-291
391172-001
398393-002
Power cord for use in the United States
Power cord for use in Australia
Power cord for use in Japan
65-W AC adapter
Bluetooth module
NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module
cable is included in the Cables Kit, spare part number 454008-001. See Cable Kit on page 21 for more Cable
Kit information.
414045-001
414046-001
417506-001
441075-002
512-MB memory module (PC2-5300, 667-MHz, DDR2)
1024-MB memory module (PC2-5300, 667-MHz, DDR2)
2048-MB memory module (PC2-5300, 667-MHz, DDR2)
Broadcom 802.11a/b/g module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and
Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana,
Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central
African Republic, Chad, Chile, People's Republic of China, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor,
Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,
Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory
Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia,
Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta,
the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,
Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand,
Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru,
the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome & Principe, Saudi Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone, Singapore,
Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis,
St. Lucia, St. Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania,
Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab
Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and
Zimbabwe
441075-291
441082-001
Broadcom 802.11a/b/g module for use in Japan
Intel 802.11a/b/g module for use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador, El
Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico, Panama,
Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay, Venezuela, and Vietnam
441082-003
Intel 802.11a/b/g module for use in Australia, New Zealand, Pakistan, the People's Republic of China, and
South Korea
441082-291
441086-002
Intel 802.11a/b/g module for use in Japan
Intel 802.11a/b/g module for use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary, Iceland,
Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, the Netherlands,
Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania, Russia, Serbia and Montenegro, Singapore,
Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the United Kingdom,
and Uzbekistan
Sequential part number listing 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Spare part
number
Description
441090-002
Broadcom 802.11b/g module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua & Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,
Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia & Herzegovina, Botswana, Brazil, the British
Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, the Central African
Republic, Chad, Chile, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic,
Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial
Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany,
Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti,
Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica,
Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein,
Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall
Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco,
Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger,
Nigeria, Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, the People's Republic of China, Peru,
the Philippines, Poland, Portugal, Qatar, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San
Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St.
Kitts & Nevis, St. Lucia, St. Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan,
Tanzania, Thailand, Togo, Tonga, Trinidad & Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine,
the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen,
Zaire, Zambia, and Zimbabwe
441090-291
445853-001
446891-001
Broadcom 802.11b/g module for use in Japan
Thermal Material Kit
Intel Core 2 Duo T7100 1.80-GHz processor (2-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
446892-001
446894-001
448674-001
Intel Core 2 Duo T7300 2.00-GHz processor (4-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
Intel Core 2 Duo T7700 2.40-GHz processor (4-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
Intel 802.11a/b/g module for use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador, El
Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico, Panama,
Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay, Venezuela, and Vietnam
448674-002
Intel 802.11a/b/g module for use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary, Iceland,
Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, the Netherlands,
Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania, Russia, Serbia and Montenegro, Singapore,
Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the United Kingdom,
and Uzbekistan
448674-003
Intel 802.11a/b/g module for use in Australia, New Zealand, Pakistan, the People's Republic of China, and
South Korea
448674-291
448675-004
449137-001
449139-001
Intel 802.11a/b/g module for use in Japan
Intel 802.11b/g module for use in Thailand
RTC battery
Modem module for use only in Japan and Asia Pacific countries and regions
NOTE: The modem module spare part kits do not include a modem module cable. The modem module cable
is included in the Cables Kit, spare part number 454008-001. See Cable Kit on page 21 for more Cable Kit
information.
451403-001
Modem module for use in all countries and regions except Japan and Asia Pacific countries and regions
26 Chapter 3 Illustrated parts catalog
Download from Www.Somanuals.com. All Manuals Search And Download.
Spare part
number
Description
NOTE: The modem module spare part kits do not include a modem module cable. The modem module cable
is included in the Cables Kit, spare part number 454008-001. See Cable Kit on page 21 for more Cable Kit
information.
453991-001
453993-001
453994-001
453996-001
453998-001
453999-001
454000-001
454001-001
454002-001
454004-001
454005-001
454008-001
454009-001
454010-001
454011-001
454014-001
454015-001
System board (includes replacement thermal material)
Base enclosure (includes rubber feet)
Top cover (includes TouchPad and cable, and fingerprint reader board and cable)
Front LED board
Heat sink (includes replacement thermal material)
Fan
Optical Drive Bezel/Bracket Kit
4-cell, 37-WH battery
8-cell, 73-WH battery
12.1-inch, WXGA, display assembly
Switch cover
Cable Kit
Display inverter
Plastics Kit
Display hinges (includes left and right display hinges)
Screw Kit
Intel Core 2 Duo T7500 2.4-GHz processor (4-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
454016-001
Intel Core 2 Duo T7800 2.6-GHz processor (4-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
454017-001
454017-281
454017-291
454017-AB1
454017-AD1
454333-001
454334-001
454335-001
454336-001
454337-001
454338-001
454398-001
Keyboard for use in the United States
Keyboard for use in Thailand
Keyboard for use in Japan
Keyboard for use in Taiwan
Keyboard for use in South Korea
DVD/CD-RW Combo Drive
DVD-ROM Drive
80-GB, 5400-rpm hard drive (includes hard drive bracket)
120-GB, 5400-rpm hard drive (includes hard drive bracket)
160-GB, 5400-rpm hard drive (includes hard drive bracket)
200-GB, 4200-rpm hard drive (includes hard drive bracket)
Display enclosure (includes 2 WLAN transceivers and cables and logo)
Sequential part number listing 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Spare part
number
Description
454599-001
454600-001
455400-001
455585-001
455586-001
456226-001
457906-001
457907-001
Intel Celeron-M 530 1.73-GHz processor (1-MB L2 cache, 533-MHz FSB, includes replacement thermal material)
Intel Celeron-M 540 1.86-GHz processor (1-MB L2 cache, 533-MHz FSB, includes replacement thermal material)
Display bezel (includes nameplate)
Miscellaneous Display Kit
Display Cable Kit
Fingerprint reader board
Speakers
ExpressCard assembly
28 Chapter 3 Illustrated parts catalog
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Removal and replacement
procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●
●
●
●
Flat-bladed screwdriver
Magnetic screwdriver
Phillips P0 and P1 screwdrivers
Torx T8 screwdriver
Service considerations
The following sections include some of the considerations that you must keep in mind during disassembly
and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.
Plastic parts
Using excessive force during disassembly and reassembly can damage plastic parts. Use care when
handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.
Preliminary replacement requirements 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations
during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat
or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In
all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that
they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme
care; these cables tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer
is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive,
avoid touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and be
sure that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
30 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some protection,
but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a
normal cycle. Or the device may function normally for a while, then degrade in the internal layers,
reducing its life expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you area ready to install them.
Use nonmagnetic tools.
Before touching an electronic component, discharge static electricity by using the guidelines described in
this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by different
activities.
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
10%
40%
55%
Walking across carpet
35,000 V
12,000 V
6,000 V
15,000 V
5,000 V
800 V
7,500 V
3,000 V
400 V
Walking across vinyl floor
Motions of bench worker
Removing DIPS from plastic tube
Removing DIPS from vinyl tray
Removing DIPS from Styrofoam
Removing bubble pack from PCB
Packing PCBs in foam-lined box
2,000 V
700 V
400 V
11,500 V
14,500 V
26,500 V
21,000 V
4,000 V
5,000 V
20,000 V
11,000 V
2,000 V
3,500 V
7,000 V
5,000 V
Preliminary replacement requirements 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●
●
●
●
●
●
●
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
Place items on a grounded surface before removing items from their containers.
Always be properly grounded when touching a component or assembly.
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam.
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized
equipment used for moving materials is wired to ground and that proper materials are selected to
avoid static charging. When grounding is not possible, use an ionizer to dissipate electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
●
●
Cover the workstation with approved static-shielding material.
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools
and equipment.
●
●
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe
materials.
●
●
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and
Styrofoam.
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these
items only at static-free workstations.
●
●
Avoid contact with pins, leads, or circuitry.
Turn off power and input signals before inserting or removing connectors or test equipment.
32 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps
with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground,
wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors,
use alligator clips to connect a wrist strap.
●
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can
be used at standing workstations and are compatible with most types of shoes or boots. On
conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one megohm
resistance between the operator and ground. To be effective, the conductive strips must be worn in
contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●
●
●
●
●
●
●
●
●
●
●
●
Antistatic tape
Antistatic smocks, aprons, and sleeve protectors
Conductive bins and other assembly or soldering aids
Nonconductive foam
Conductive tabletop workstations with ground cords of one megohm resistance
Static-dissipative tables or floor mats with hard ties to the ground
Field service kits
Static awareness labels
Material-handling packages
Nonconductive plastic bags, tubes, or boxes
Metal tote boxes
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material
Use
Voltage protection level
Antistatic plastic
Bags
1,500 V
7,500 V
5,000 V
Carbon-loaded plastic
Metallized laminate
Floor mats
Floor mats
Preliminary replacement requirements 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Unknown user password
If the computer you are servicing has an unknown user password, follow these steps to clear the password:
NOTE: These steps also clear CMOS.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
Disconnect all external devices connected to the computer.
2.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
5.
6.
7.
8.
Wait approximately 5 minutes.
Replace the RTC battery and reassemble the computer.
Connect AC power to the computer. Do not reinsert any batteries at this time.
9. Turn on the computer.
All passwords and all CMOS settings have been cleared.
34 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 84 screws, in 15 different sizes, that must be removed, replaced, or loosened when
servicing the computer. Make special note of each screw size and location during removal and
replacement.
Serial number
Report the computer serial number to HP when requesting information or ordering spare parts. The serial
number is located on the bottom of the computer.
Component replacement procedures 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer feet
The computer feet are adhesive-backed rubber pads. The feet are included in the Plastics Kit, spare part
number 454010-001. There are 4 rubber feet that attach to the base enclosure in the locations illustrated
below.
36 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery
Description
Spare part number
8-cell, 2.55-Ah (73-Wh) Li-ion battery
4-cell, 2.20-Ah (37-Wh) Li-ion battery
454002-001
454001-001
Before disassembling the computer, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
2. Disconnect all external devices connected to the computer.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
3.
Remove the battery:
Turn the computer upside down on a flat surface, with the battery bay toward you.
1.
2. Slide the battery release latch (1) to release the battery.
3. Remove the battery (2) from the computer.
Install the battery by inserting it into the battery bay until you hear a click.
Component replacement procedures 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Hard drive
NOTE: All hard drive spare part kits include a hard drive bracket.
Description
Spare part number
200-GB, 4200-rpm hard drive
160-GB, 5400-rpm hard drive
120-GB, 5400-rpm hard drive
80-GB, 5400-rpm hard drive
454338-001
454337-001
454336-001
454335-001
Before removing the hard drive, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
Disconnect all external devices connected to the computer.
2.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the hard drive:
Position the computer with the front toward you.
1.
2. Loosen the four Phillips PM2.0×5.0 captive screws (1) that secure the hard drive cover to the
computer.
3. Lift the rear edge of the hard drive cover (2), swing it up and forward, and remove the cover. The
hard drive cover is included in the Plastics Kit, spare part number 454010-001.
4. Loosen the Phillips PM2.5×12.0 captive screw (1) that secures the hard drive to the computer.
38 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Grasp the Mylar tab (2) on the hard drive and slide the hard drive (3) to the left to disconnect it
from the system board.
6. Remove the hard drive (4) from the hard drive bay.
If it is necessary to replace the hard drive bracket, remove the two Phillips PM3.0×4.0 hard drive
bracket screws (1) from each side of the hard drive.
7.
8. Lift the bracket (2) straight up to remove it from the hard drive.
Reverse this procedure to reassemble and install the hard drive.
Component replacement procedures 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory module
Description
Spare part number
2048-MB (PC2-5300, 667-MHz, DDR2)
417506-001
414046-001
414045-001
1024-MB (PC2-5300, 667-MHz, DDR2)
512-MB (PC2-5300, 667-MHz, DDR2)
Before removing the memory module, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
Disconnect all external devices connected to the computer.
2.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the memory module:
Position the computer with the front toward you.
1.
2. Loosen the two Phillips PM2.0×5.0 captive screws (1) that secure the memory module compartment
cover to the computer.
3. Lift the left side of the cover (2), swing it up and to the right, and remove the cover. The memory
module compartment cover is included in the Plastics Kit, spare part number 454010-001.
4. Spread the retaining tabs (1) on each side of the memory module slot to release the memory module.
(The edge of the module opposite the slot rises away from the computer.)
40 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Remove the memory module (2) by pulling the module away from the slot at an angle.
NOTE: Memory modules are designed with a notch (3) to prevent incorrect installation into the
memory module slot.
Reverse this procedure to install a memory module.
Component replacement procedures 41
Download from Www.Somanuals.com. All Manuals Search And Download.
WLAN module
CAUTION: The WLAN module and the WWAN module are not interchangeable.
Description
Spare part number
Intel 802.11a/b/g/n WLAN modules:
●
●
For use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei, 441086-001
Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador,
El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia,
Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay, the United States,
Venezuela, and Vietnam
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech 441086-002
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania,
Russia, Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka,
Sweden, Switzerland, Turkey, Ukraine, the United Kingdom, and Uzbekistan
●
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South Korea 441086-003
For use in Japan
441086-291
Broadcom 802.11a/b/g WLAN modules:
●
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, 441075-002
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,
Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana,
Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape
Verde, the Central African Republic, Chad, Chile, People's Republic of China, Colombia,
Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti,
Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea,
Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia,
Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-
Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the
Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius,
Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia,
Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria,
Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines,
Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao
Tome & Principe, Saudi Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain,
Sri Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent & Grenada, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom,
Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
●
For use in Japan
441075-291
Intel 802.11a/b/g WLAN modules:
●
●
For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei,
Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador,
El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia,
Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay,
Venezuela, and Vietnam
448674-001
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech 448674-002
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania,
42 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
Spare part number
Russia, Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka,
Sweden, Switzerland, Turkey, Ukraine, the United Kingdom, and Uzbekistan
●
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South Korea 448674-003
For use in Japan
448674-291
Broadcom 802.11b/g WLAN modules:
●
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua & Barbuda, Argentina,
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,
Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia & Herzegovina, Botswana,
Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon,
Cape Verde, the Central African Republic, Chad, Chile, Colombia, Comoros, the Congo, Costa
Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican
Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia,
Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar,
Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras,
Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica,
Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the
Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria,
Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, the People's Republic of China,
Peru, the Philippines, Poland, Portugal, Qatar, the Republic of Moldova, Romania, Russia,
Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia and
Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands,
Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent &
Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Thailand,
Togo, Tonga, Trinidad & Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the
United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zaire, Zambia, and Zimbabwe
441090-002
●
For use in Japan
441090-291
448675-004
Intel 802.11b/g WLAN module for use in Japan
Before removing the WLAN module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
3.
Remove the WLAN module:
1. Position the computer with the front toward you.
2. Loosen the Phillips PM2.0×5.0 captive screw (1) that secures the WLAN module compartment cover
to the computer.
Component replacement procedures 43
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Lift the right side of the cover, swing it up and to the left, and remove the cover.
4. Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module.
NOTE: The black WLAN antenna cable is connected to the WLAN module “Main” terminal. The
white WLAN antenna cable is connected to the WLAN module “Aux” terminal.
5. Remove the two Phillips PM2.5×4.0 screws (2) that secure the WLAN module to the computer. (The
edge of the module opposite the slot rises away from the computer.)
6. Remove the WLAN module (3) by pulling the module away from the slot at an angle.
NOTE: WLAN modules are designed with a notch (4) to prevent incorrect installation.
Reverse this procedure to install the WLAN module.
44 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Optical drive
NOTE: All optical drive spare part kits include an optical drive bezel.
Description
Spare part number
DVD/CD-RW Combo Drive
DVD-ROM Drive
454333-001
454334-001
Before removing the optical drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the optical drive:
1. Position the computer with the right side toward you.
2. Remove the Torx T8M2.5×7.0 screw (1) that secures the optical drive to the computer.
3. Insert a flat-bladed screwdriver or similar tool into the optical drive tab access (2) and press the tab
to the right to release the optical drive from the computer.
4. Remove the optical drive (3) from the computer.
5. If it is necessary to replace the optical drive bracket, position the optical drive with the rear toward
you.
6. Remove the two Phillips PM2.0×4.0 screws (1) that secure the optical drive bracket to the optical
drive.
Component replacement procedures 45
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Remove the optical drive bracket (2).
Reverse this procedure to reassemble and install an optical drive.
46 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Keyboard
For use in:
Spare part number
For use in:
Spare part number
Japan
Korea
Taiwan
454017-291
454017-AD1
454017-AB1
Thailand
454017-281
454017-001
The United States
Before removing the keyboard, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
Disconnect all external devices connected to the computer.
2.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the keyboard:
Turn the computer upside down, with the front toward you.
1.
2. Loosen the three Phillips PM2.5×7.0 captive screws that secure the keyboard to the computer.
Turn the computer display-side up, with the front toward you.
Open the computer as far as possible.
3.
4.
5. Lift the rear edge of the keyboard (1) until it rests at an angle.
Component replacement procedures 47
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Move the keyboard (2) toward the display until the tabs on the keyboard bottom edge disengage
from the top cover.
7. Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached, and
disconnect the keyboard cable (2) from the system board.
8. Remove the keyboard.
Reverse this procedure to install the keyboard.
48 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch cover
Description
Spare part number
Switch cover (includes LED board and LED board cable)
454006-001
Before removing the switch cover, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the switch cover:
Turn the computer upside down, with the rear panel toward you.
Remove the following:
1.
2.
(1) Two rubber screw covers. The rubber screw covers are included in the Plastics Kit, spare part
number 454010-001.
(2) Three Phillips PM2.5×7.0 screws.
(3) Five Phillips PM2.0×3.0 screws.
Turn the computer right-side up, with the front toward you.
Open the computer as far as possible.
3.
4.
Component replacement procedures 49
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Disconnect the LED board cable (1) from the system board.
6. Remove the switch cover (2).
Reverse this procedure to install the switch cover.
50 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Display assembly
Description
Spare part number
12.1-inch, WXGA display assembly (includes WLAN antenna transceivers and cables)
454004-001
Before removing the display assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the display assembly:
Close the computer and turn it upside down, with the rear panel toward you.
1.
2. Remove the Phillips PM2.5×7.0 screw (1) and Phillips PM2.5×5.0 screw (2) that secure the display
assembly to the computer.
Turn the computer right-side up, with the front toward you.
3.
4. Open the computer as far as possible.
5. Disconnect the display panel cable (1) from the system board.
Component replacement procedures 51
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Remove the WLAN antenna cables (2) from the opening in the system board.
7. Remove the four Phillips PM2.5×6.0 screws (1) that secure the display assembly to the computer.
8. Lift the display assembly (2) straight up and remove it.
52 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
9. If it is necessary to replace the display bezel or the display assembly internal components, remove
the six rubber screw covers (1) and the six Torx T8M2.5×6.0 screws (2) that secure the display
bezel to the display enclosure.
10. Flex the inside edges of the left and right sides (1) and the top and bottom sides (2) of the display
bezel until the bezel disengages from the display enclosure.
11. Remove the display bezel (3). The display bezel is available using spare part number
455400-001.
12. If it is necessary to replace the display inverter, release the inverter (1) as far as the display panel
cable and backlight cable allow.
Component replacement procedures 53
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Disconnect the backlight cable (2) and the display panel cable (3) from the display inverter.
Remove the display inverter from the display enclosure. The display inverter is available using spare
part number 454009-001.
14.
15. If it is necessary to replace the display hinges, remove the six Torx T8M2.5×5.0 screws (1) that
secure the display panel to the display enclosure.
16. Remove the display panel (2) from the display enclosure.
17. Remove the two Phillips PM2.0×4.0 screws (1) that secure the display hinges to the display panel.
54 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
18. Remove the display hinges (2) from the display panel. The display hinges are available using spare
part number 454011-001.
Reverse this procedure to reassemble and install the display assembly.
Top cover
Description
Spare part number
Top cover (includes TouchPad and cable, and fingerprint reader board and cable)
453994-001
Before removing the top cover, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
Disconnect all external devices connected to the computer.
2.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the following components:
5.
a.
b.
c.
e.
Remove the top cover:
1. Turn the computer upside down, with the front toward you.
Component replacement procedures 55
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Remove the following:
(1) Two rubber screw covers. The rubber screw covers are included in the Plastics Kit, spare part
number 454010-001.
(2) Seven Phillips PM2.5×7.0 screws.
(3) Three Phillips PM2.0×3.0 screws.
Turn the computer right-side up, with the front toward you.
3.
4. Disconnect the fingerprint reader board cable (1) from the system board.
5. Disconnect the TouchPad cable (2) from the system board.
6. Remove the two Phillips PM2.5×7.0 screws (3) and the two Phillips PM2.5×4.0 screws (4) that
secure the top cover to the computer.
56 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Lift the rear edge of the top cover (1) and swing it (2) up and forward until it rests at an angle.
8. Lift the top cover (3) straight up and remove it.
Reverse this procedure to install the top cover.
Component replacement procedures 57
Download from Www.Somanuals.com. All Manuals Search And Download.
RTC battery
NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all passwords
and CMOS settings to be cleared.
Description
Spare part number
RTC battery
449137-001
Before removing the RTC battery, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
Disconnect all external devices connected to the computer.
2.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the following components:
4.
5.
a.
b.
c.
f.
Remove the RTC battery:
1. Disconnect the RTC battery cable (1) from the system board.
58 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Remove the RTC battery (2).
Reverse this procedure to install the RTC battery.
Component replacement procedures 59
Download from Www.Somanuals.com. All Manuals Search And Download.
Front LED board
Description
Spare part number
Front LED board
453996-001
Before removing the front LED board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
5. Remove the following components:
b.
c.
d.
e.
f.
Remove the front LED board:
1. Disconnect the front LED board cable (1) from the system board.
2. Remove the two Phillips PM2.0×3.0 screws (2) that secure the front LED board to the base enclosure.
60 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Remove the front LED board (3).
Reverse this procedure to reassemble and install the front LED board.
Bluetooth module
NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth
module cable is included in the Cables Kit, spare part number 454008-001. See Cable Kit
on page 21 for more Cable Kit information.
Description
Spare part number
Bluetooth
398393-002
Before removing the Bluetooth module, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
Disconnect all external devices connected to the computer.
2.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the following components:
4.
5.
a.
b.
c.
d.
Component replacement procedures 61
Download from Www.Somanuals.com. All Manuals Search And Download.
f.
Remove the Bluetooth module:
1. Disconnect the Bluetooth module cable (1) from the system board.
2. Remove the two Phillips PM2.0×4.0 screws (2) that secure the Bluetooth module to the system board.
3. Remove the module (3).
Reverse this procedure to install the Bluetooth module.
Speaker assembly
Description
Spare part number
Speaker assembly
457906-001
Before removing the speaker assembly, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
Disconnect all external devices connected to the computer.
2.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
62 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove the following components:
5.
a.
b.
c.
e.
f.
g.
Remove the speaker assembly:
1. Disconnect the speaker assembly cable (1) from the system board.
2. Remove the speaker assembly (2) from the base enclosure.
Reverse this procedure to install the speaker assembly.
Component replacement procedures 63
Download from Www.Somanuals.com. All Manuals Search And Download.
Microphone
Kit on page 21 for more Cable Kit information.
Before removing the microphone, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
Disconnect all external devices connected to the computer.
2.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the following components:
4.
5.
a.
c.
e.
f.
g.
Remove the microphone:
1. Disconnect the microphone cable (1) from the system board.
2. Remove the microphone receiver (2) from the clip built into the base enclosure.
64 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Reverse this procedure to install the microphone.
System board
Description
Spare part number
System board (includes replacement thermal material)
453991-001
Before removing the system board, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
Disconnect all external devices connected to the computer.
2.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the following components:
4.
5.
a.
b.
d.
f.
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
●
●
●
●
●
●
●
Remove the system board:
1. Remove the three Phillips PM2.5×6.0 screws (1) that secure the system board to the base enclosure.
Component replacement procedures 65
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Loosen the captive standoff (2) on the fan that secures the system board to the base enclosure.
3. Flex the left side of the base enclosure (1) until the USB, RJ-45, and RJ-11 jacks (2) clear the openings
in the base enclosure.
4. Use the optical drive connector (1) to lift the left side of the system board (2) until it rests at an angle.
5. Remove the system board (3) from the base enclosure by pulling it away at an angle.
Reverse the preceding procedure to install the system board.
66 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
ExpressCard assembly
Description
Spare part number
ExpressCard assembly
457907-001
Before removing the ExpressCard assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
5. Remove the following components:
b.
c.
d.
e.
f.
g.
h.
Remove the ExpressCard assembly:
Turn the system board upside down, with the left side toward you.
1.
Component replacement procedures 67
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Remove the four Phillips PM2.0×6.0 screws that secure the ExpressCard assembly to the system
board.
Turn the system board right-side up, with the left side toward you.
Remove the ExpressCard assembly from the system board.
3.
4.
Reverse this procedure to install the ExpressCard assembly.
68 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem module
NOTE: The modem module spare part kits doe not include a modem module cable. The modem module
cable is included in the Cables Kit, spare part number 454008-001. See Cable Kit on page 21 for more
Cable Kit information.
Description
Spare part number
For use in all countries and regions except Japan and Asia Pacific countries and regions
For use only in Japan and Asia Pacific countries and regions
451403-001
449139-001
Before removing the modem module, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
Disconnect all external devices connected to the computer.
2.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the following components:
4.
5.
a.
b.
d.
f.
g.
h.
Remove the modem module:
1. Turn the system board upside down, with the rear edge toward you.
2. Remove the two Phillips PM2.5×4.0 screws (1) that secure the modem module to the system board.
Component replacement procedures 69
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Disconnect the modem module (2) from the system board by lifting it straight up.
4. Remove the modem module and modem module cable.
Reverse this procedure to install the modem module and modem module cable.
70 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Fan
Description
Spare part number
Fan
453999-001
Before removing the fan, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
5. Remove the following components:
b.
c.
d.
e.
f.
g.
h.
Remove the fan:
Turn the system board upside down, with the rear edge toward you.
1.
2. Disconnect the fan cable (1) from the system board.
3. Remove the three Phillips PM2.0×4.0 screws (2) that secure the fan to the heat sink.
Component replacement procedures 71
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Remove the fan (3) from the heat sink.
Reverse this procedure to install the fan.
NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left side of
the computer.
The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is
designed to turn on automatically when high temperature conditions exist. These conditions are affected
by high external temperatures, system power consumption, power management/battery conservation
configurations, battery fast charging, and software requirements. Exhaust air is displaced through the
ventilation grill located on the left side of the computer.
72 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Heat sink
Description
Spare part number
Heat sink (includes a heat sink clip and replacement thermal material)
Thermal Material Kit
453998-001
445853-001
Before removing the heat sink, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
2. Disconnect all external devices connected to the computer.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
3.
5. Remove the following components:
b.
c.
d.
e.
f.
h.
i.
Remove the heat sink:
1. Remove the two Phillips PM2.0×6.0 shoulder screws (1) that secure the heat sink and the heat sink
retention clips to the system board.
2. Remove the heat sink retention clips (2) by sliding them to the left.
Component replacement procedures 73
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Remove the heat sink (3) by lifting it straight up.
NOTE: Due to the adhesive quality of the thermal material located between the heat sink and
system board components, it may be necessary to move the heat sink from side to side to detach the
assembly.
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink (1) and
(3), the processor (2), and graphics subsystem component (4) on the system board each time the heat
sink is removed. Thermal material is included with all system board, heat sink, and processor spare part
kits, and is also available in the Thermal Material Kit, spare part number 445853-001.
Reverse this procedure to install the heat sink.
74 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Processor
NOTE: All processor spare part kits include replacement thermal material. The Thermal Material Kit is
also available using spare part number 445853-001.
Description
Spare part number
Intel Core 2 Duo processors (4-MB L2 cache, 800-MHz FSB)
T7800 2.6-GHz processor
454016-001
446894-001
454015-001
446892-001
446891-001
T7700 2.4-GHz processor
T7500 2.2-GHz processor
T7300 2.0-GHz processor
T7100 1.8-GHz processor
Intel Core Duo processors (2-MB L2 cache, 667-MHz FSB)
T5450 1.66-GHz processor
454598-001
455399-001
T5250 1.50-GHz processor
Intel Celeron-M processors (1-MB L2 cache, 533-MHz FSB)
540 1.86-GHz processor
454600-001
454599-001
530 1.73-GHz processor
Before removing the processor, follow these steps:
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
1.
Disconnect all external devices connected to the computer.
2.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the following components:
4.
5.
a.
c.
e.
f.
g.
h.
Component replacement procedures 75
Download from Www.Somanuals.com. All Manuals Search And Download.
i.
j.
Remove the processor:
1. Use a flat-bladed screwdriver to turn the processor locking screw (1) one-half turn counterclockwise
until you hear a click.
2. Lift the processor (2) straight up and remove it.
NOTE: When you install the processor, the gold triangle (3) on the processor must be aligned with
the triangle (4) embossed on the processor slot.
Reverse this procedure to install the processor.
76 Chapter 4 Removal and replacement procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Computer Setup
Starting Computer Setup
Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is
not working or will not load.
NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your
computer.
NOTE: Pointing devices are not supported in Computer Setup. You must use the keyboard to navigate
and make selections.
NOTE: An external keyboard connected by USB can be used with Computer Setup only if USB legacy
support is enabled.
To start Computer Setup, follow these steps:
Turn on or restart the computer.
1.
2. Before Windows® opens and while the "F10 = ROM Based Setup" message is displayed in the
lower-left corner of the screen, press f10.
Starting Computer Setup 77
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Computer Setup
Navigating and selecting in Computer Setup
The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and
System Configuration menus.
1. Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the
"F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen.
Because Computer Setup is not Windows-based, it does not support the TouchPad. Navigation and
selection are by keystroke:
●
●
●
●
●
To choose a menu or a menu item, use the arrow keys.
To select an item, press enter.
To close open dialog boxes and return to the main Computer Setup screen, press esc.
To view navigation information, press f1.
To change the language, press f2.
2. Select the File, Security, Diagnostics, or System Configuration menu.
To exit Computer Setup, choose one of the following methods:
3.
●
To exit Computer Setup without saving your preferences, use the arrow keys to select File >
Ignore Changes and Exit. Then follow the instructions on the screen.
●
To save your preferences and exit Computer Setup, use the arrow keys to select File > Save
Changes and Exit. Then follow the instructions on the screen.
Your preferences go into effect when the computer restarts.
Restoring factory settings in Computer Setup
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the
"F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen.
1.
2. Use the arrow keys to select File > Restore defaults, and then press enter.
3. When the confirmation dialog box opens, press f10.
4. To save your preferences and exit Computer Setup, use the arrow keys to select File > Save
Changes and Exit. Then follow the instructions on the screen.
Your preferences go into effect when the computer restarts.
NOTE: Your password settings and security settings are not changed when you restore the factory
settings.
78 Chapter 5 Computer Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Setup menus
The menu tables in this section provide an overview of Computer Setup options.
NOTE: Some of the Computer Setup menu items listed in this chapter may not be supported by your
computer.
File menu
Select
To do this
System information
●
●
View identification information for the computer and the batteries in the system.
View specification information for the processor, cache and memory size,
system ROM, video revision, and keyboard controller version.
Restore defaults
Replace the configuration settings in Computer Setup with the original factory
settings. (Password settings and security settings are not changed when you restore
the factory settings.)
Ignore changes and exit
Save changes and exit
Cancel any changes entered during the current session. Then exit and restart the
computer.
Save any changes entered during the current session. Then exit and restart the
computer. Your changes go into effect when the computer restarts.
Computer Setup menus 79
Download from Www.Somanuals.com. All Manuals Search And Download.
Security menu
Select
To do this
Setup password
Enter, change, or delete a setup password.
Enter, change, or delete a power-on password.
Power-On password
Password options
●
●
●
Enable/disable stringent security.
Enable/disable password requirement on computer restart.
DriveLock passwords
Enable/disable DriveLock on any computer hard drive and on optional
MultiBay hard drives.
●
Change a DriveLock user password or master password.
NOTE: DriveLock settings are accessible only when you enter Computer Setup by
turning on (not restarting) the computer.
Smart Card security
Enable/disable support for smart card and Java™ Card power-on authentication.
NOTE: Power-on authentication for smart cards is supported only on computers
with optional smart card readers.
NOTE: You must have an administrator password to change this setting.
TPM Embedded Security
Enable/disable support for Trusted Platform Module (TPM) Embedded Security,
which protects the computer from unauthorized access to owner functions available
in Embedded Security for ProtectTools. For more information, refer to the
ProtectTools software Help.
NOTE: You must have a setup password to change this setting.
System IDs
Enter user-defined computer asset tracking number and ownership tag.
Disk Sanitizer
Run Disk Sanitizer to destroy all existing data on the primary hard drive. The
following options are available:
●
●
●
Fast: Runs the Disk Sanitizer erase cycle once.
Optimum: Runs the Disk Sanitizer erase cycle 3 times.
Custom: Allows you to select the desired number of Disk Sanitizer erase cycles
from a list.
CAUTION: If you run Disk Sanitizer, the data on the primary hard drive is
destroyed permanently.
Diagnostics menu
Select
To do this
Hard Drive Self-Test options
Run a comprehensive self-test on any hard drive in the system or on any optional
MultiBay hard drive.
Memory Check
Run a comprehensive check on system memory.
Startup Check (select models only)
Verify the system components needed for starting the computer.
80 Chapter 5 Computer Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
System Configuration menu
NOTE: Some of the listed System Configuration options may not be supported by your computer.
Select
To do this
Language (or press f2)
Boot options
Change the Computer Setup language.
●
●
●
●
Set f9, f10, and f12 delay when starting up.
Enable/disable CD-ROM boot.
Enable/disable floppy boot.
Enable/disable internal network adapter boot and set the boot mode (PXE or
RPL).
●
Enable/disable MultiBoot, which sets a boot order that can include most boot
devices in the system.
●
●
●
●
Set the Express Boot Popup delay in seconds.
Set the boot order.
Device configurations
Swap the functions of the fn key and left ctrl key.
Enable/disable multiple standard pointing devices at startup. (To set the
computer to support only a single, usually nonstandard, pointing device at
startup, select Disable.)
●
Enable/disable USB legacy support. When enabled, USB legacy support
allows the following:
◦
Use of a USB keyboard, mouse, and hub in Computer Setup even when
a Windows operating system is not running.
◦
Startup from bootable USB devices, including a hard drive, diskette drive,
or optical drive connected by a USB port to the computer or to an optional
docking device (select models only).
●
Select a parallel port mode: EPP (Enhanced Parallel Port), standard,
bidirectional, or ECP (Enhanced Capabilities Port).
●
●
●
Enable/disable BIOS DMA data transfers.
Enable/disable fan always on while connected to an AC outlet.
Enable/disable Intel® Data Execution Prevention or AMD® PSAE Execution
Disable. When enabled, the processor can disable some virus code execution,
which helps to improve computer security.
●
Enable/disable LAN Power Save. When enabled, saves power by turning off
the LAN when not in use.
●
●
●
●
●
●
Enable/disable SATA Native Mode.
Enable/disable Dual Core CPU.
Enable/disable Secondary Battery Fast Charge.
Choose Bit-shift or LBA assisted HDD Translation Mode.
Enable/disable Windows direct application launcher.
Enable/disable HP Lockout.
Computer Setup menus 81
Download from Www.Somanuals.com. All Manuals Search And Download.
Select
To do this
Built-In Device Options
●
●
●
●
Enable/disable embedded WWAN Device Radio.
Enable/disable embedded WLAN Device Radio.
Enable/disable embedded Bluetooth® Device Radio.
Enable/disable LAN/WLAN Switching. When enabled, switches to a WLAN
when a LAN is either unavailable or disconnected.
●
●
●
●
●
●
Enable/disable Wake on LAN from Off.
Enable/disable the ambient light sensor.
Enable/disable the serial port.
Port Options
Enable/disable the parallel port.
Enable/disable the flash media reader.
Enable/disable the USB port.
CAUTION: Disabling the USB port also disables MultiBay devices and
ExpressCard devices on the advanced port replicator.
●
●
●
●
●
●
Enable/disable the 1394 port.
Enable/disable the cardbus slot.
Enable/disable the ExpressCard slot.
Enable/disable the infrared port.
Enable/disable the optical disk drive.
Enable/disable the network controller.
82 Chapter 5 Computer Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Specifications
Computer specifications
Metric
U.S.
Dimensions
Length
30.6 cm
12.01 in
Width
22.5 cm
8.86 in
Height (front to rear)
Weight
2.8 to 3.3 cm
1.10 to 1.29 in
Equipped with 8-cell battery and optical drive
Equipped with 4-cell battery and optical drive
Input power
2.12 kg
1.92 kg
4.67 lbs
4.23 lbs
Operating voltage
19.0 V dc @ 4.74 A – 65 W
4.74 A
Operating current
Temperature
Operating (not writing to optical disc)
Operating (writing to optical disc)
Nonoperating
0°C to 35°C
5°C to 35°C
-20°C to 60°C
32°F to 95°F
41°F to 95°F
-4°F to 140°F
Relative humidity
Operating
10% to 90%
5% to 95%
Nonoperating
Maximum altitude (unpressurized)
Operating (14.7 to 10.1 psia)
Nonoperating (14.7 to 4.4 psia)
Shock
-15 m to 3,048 m
-15 m to 12,192 m
50 ft to 10,000 ft
-50 ft to 40,000 ft
Operating
125 g, 2 ms, half-sine
200 g, 2 ms, half-sine
Nonoperating
Random vibration
Computer specifications 83
Download from Www.Somanuals.com. All Manuals Search And Download.
Metric
U.S.
Operating
0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep
rate
Nonoperating
1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
range of temperatures.
12.1-inch, WXGA display specifications
Metric
U.S.
Dimensions
Height
16.9 cm
6.7 in
Width
26.2 cm
10.3 in
12.1 in
Diagonal
30.8 cm
Number of colors
Contrast ratio
Brightness
Up to 16.8 million
250:1 (typical)
180 nits (typical)
Pixel resolution
Pitch
0.279 × 0.279 mm
1280 × 800
RGB vertical stripe
Edge lit
Format
Configuration
Backlight
Character display
Total power consumption
Viewing angle
80 × 25
4.0 W
+/-40 horizontal, +120/–40° vertical (typical)
84 Chapter 6 Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Hard drive specifications
200-GB*
160-GB*
120-GB*
80-GB*
Dimensions
Height
9.5 mm
9.5 mm
9.5 mm
9.5 mm
Width
70 mm
70 mm
70 mm
70 mm
Weight
101 g
101 g
101 g
101 g
Interface type
Transfer rate
Security
SATA
SATA
SATA
SATA
100 MB/sec
ATA security
100 MB/sec
ATA security
100 MB/sec
ATA security
100 MB/sec
ATA security
Seek times (typical read, including setting)
Single track
3 ms
3 ms
3 ms
3 ms
Average
13 ms
13 ms
13 ms
13 ms
Maximum
24 ms
24 ms
24 ms
24 ms
Logical blocks
Disc rotational speed
Operating temperature
390,700,850
4200 rpm
312,560,640
5400 rpm
234,420,480
5400 rpm
156,280,320
5400 rpm
5°C to 55°C (41°F to 131°F)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive specifications
may differ slightly.
NOTE: Certain restrictions and exclusions apply. Contact technical support for details.
Hard drive specifications 85
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD/CD-RW Combo Drive specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-R and CD-RW
CD-ROM XA, MIXED MODE CD, CD-I, CD-I
Bridge (Photo-CD, Video CD), Multisession CD
(Photo-CD, CD-EXTRA, Portfolio, CD-R, CD-RW),
CD-R, CD-RW, DVD-ROM (DVD-5, DVD-9,
DVD-10, DVD-18), DVD-R, DVD-RW, DVD+R,
DVD+RW, DVD-RAM
Center hole diameter
Disc diameter
Standard disc
Mini disc
1.5 cm (0.59 in)
12 cm (4.72 in)
8 cm (3.15 in)
1.2 mm (0.047 in)
0.74 μm
Disc thickness
Track pitch
Access time
Random
CD
DVD
< 110 ms
< 210 ms
Line-out, 0.7 Vrms
2 MB
< 130 ms
< 225 ms
Full stroke
Audio output level
Cache buffer
Data transfer rate
24X CD-ROM
8X DVD
3,600 KB/sec
3,600 KB/sec
3,600 KB/sec
3,600 KB/sec
Multiword DMA mode 2
< 15 seconds
24X CD-R
24X CD-RW
Transfer mode
Startup time
Stop time
< 6 seconds
86 Chapter 6 Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD-ROM Drive
Applicable disc
DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18, CD-ROM (Mode 1 and 2), CD Digital
Audio, CD-XA ready (Mode 2, Form 1 and Form 2), CD-I (Mode 2, Form 1 and Form 2),
CD-R, CD-RW, Photo CD (single and multisession), CD-Bridge
Center hole diameter
Disc diameter
Standard disc
Mini disc
1.5 cm (0.59 in)
12 cm (4.72 in)
8 cm (3.15 in)
1.2 mm (0.047 in)
0.74 μm
Disc thickness
Track pitch
Access time
Random
CD
DVD
< 100 ms
< 175 ms
Line-out, 0.7 Vrms
512 KB
< 125 ms
< 225 ms
Full stroke
Audio output level
Cache buffer
Data transfer rate
CD-R (24X)
3600 KB/s (150 KB/s at 1X CD rate)
1500 KB/s (150 KB/s at 1X CD rate)
3600 KB/s (150 KB/s at 1X CD rate)
10,800 KB/s (1,352 KB/s at 1X DVD rate)
16.6 MB/s
CD-RW (10X)
CD-ROM (24X)
DVD (8X)
Multiword DMA mode 2
Startup time
Stop time
< 10 seconds
< 3 seconds
DVD-ROM Drive 87
Download from Www.Somanuals.com. All Manuals Search And Download.
System DMA specifications
Hardware DMA
System function
DMA0
DMA1*
DMA2*
DMA3
DMA4
DMA5*
DMA6
DMA7
Not applicable
Not applicable
Not applicable
Not applicable
Direct memory access controller
Available for PC Card
Not assigned
Not assigned
*PC Card controller can use DMA 1, 2, or 5.
88 Chapter 6 Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
System interrupt specifications
Hardware IRQ
System function
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5*
System timer
Standard 101-/102-Key or Microsoft® Natural Keyboard
Cascaded
Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD
COM1
Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax
Modem with SmartCP
IRQ6
Diskette drive
IRQ7*
IRQ8
Parallel port
System CMOS/real-time clock
Microsoft ACPI-compliant system
Intel USB UHCI controller—24C2
Intel 82852/82855 GM/GME Graphic Controller
Realtek RTL8139 Family PCI Fast Ethernet Controller
Intel USB EHCI controller—24CD
Intel USB UHCI controller—24C4
Intel USB UHCI controller—24C7
Intel Pro/Wireless 2200BG
TI OHCI 1394 host controller
TI PCI1410 CardBus controller
Synaptics PS/2 TouchPad
IRQ9*
IRQ10*
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
Numeric data processor
Primary IDE channel
Secondary IDE channel
*Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
NOTE: PC Cards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial port
may assert IRQ3 or IRQ4.
System interrupt specifications 89
Download from Www.Somanuals.com. All Manuals Search And Download.
System I/O address specifications
I/O address (hex)
System function (shipping configuration)
000 - 00F
010 - 01F
020 - 021
022 - 024
025 - 03F
02E - 02F
040 - 05F
044 - 05F
060
DMA controller no. 1
Unused
Interrupt controller no. 1
Opti chipset configuration registers
Unused
87334 “Super I/O” configuration for CPU
Counter/timer registers
Unused
Keyboard controller
061
Port B
062 - 063
064
Unused
Keyboard controller
065 - 06F
070 - 071
072 - 07F
080 - 08F
090 - 091
092
Unused
NMI enable/RTC
Unused
DMA page registers
Unused
Port A
093 - 09F
0A0 - 0A1
I/O Address (hex)
0A2 - 0BF
0C0 - 0DF
0E0 - 0EF
0F0 - 0F1
0F2 - 0FF
100 - 16F
170 - 177
178 - 1EF
1F0 - 1F7
1F8 - 200
201
Unused
Interrupt controller no. 2
System Function (shipping configuration)
Unused
DMA controller no. 2
Unused
Coprocessor busy clear/reset
Unused
Unused
Secondary fixed disk controller
Unused
Primary fixed disk controller
Unused
JoyStick (decoded in ESS1688)
Unused
202 - 21F
90 Chapter 6 Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
I/O address (hex)
220 - 22F
230 - 26D
26E - 26
System function (shipping configuration)
Entertainment audio
Unused
Unused
278 - 27F
280 - 2AB
2A0 - 2A7
2A8 - 2E7
2E8 - 2EF
2F0 - 2F7
2F8 - 2FF
Unused
Unused
Unused
Unused
Reserved serial port
Unused
Infrared port
300 - 31F
320 - 36F
370 - 377
378 - 37F
380 - 387
388 - 38B
38C - 3AF
3B0 - 3BB
3BC - 3BF
3C0 - 3DF
3E0 - 3E1
3E2 - 3E3
3E8 - 3EF
3F0 - 3F7
3F8 - 3FF
Unused
Unused
Secondary diskette drive controller
Parallel port (LPT1/default)
Unused
FM synthesizer—OPL3
Unused
VGA
Reserved (parallel port/no EPP support)
VGA
PC Card controller in CPU
Unused
Internal modem
“A” diskette controller
Serial port (COM1/default)
PCI configuration index register (PCIDIVO-1)
PCI configuration data register (PCIDIVO-1)
CF8 - CFB
CFC - CFF
System I/O address specifications 91
Download from Www.Somanuals.com. All Manuals Search And Download.
System memory map specifications
Size
Memory address
System function
640 KB
128 KB
48 KB
160 KB
64 KB
15 MB
58 MB
58 MB
2 MB
00000000-0009FFFF
000A0000-000BFFFF
000C0000-000CBFFF
000C8000-000E7FFF
000E8000-000FFFFF
00100000-00FFFFFF
04800000-07FFFFFF
04800000-07FFFFFF
08000000-080FFFFF
08200000-FFFEFFFF
FFFF0000-FFFFFFFF
Base memory
Video memory
Video BIOS
Unused
System BIOS
Extended memory
Super extended memory
Unused
Video memory (direct access)
Unused
4 GB
64 KB
System BIOS
92 Chapter 6 Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Screw listing
This section provides specification and reference information for the screws used in the computer. All
screws listed in this section are available in the Screw Kit, spare part number 454014-001.
Phillips PM2.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
11
4.0 mm
2.0 mm
4.5 mm
Where used: 2 screws that secure the optical drive bracket to the optical drive
Phillips PM2.0×4.0 screw 93
Download from Www.Somanuals.com. All Manuals Search And Download.
Where used: 4 screws that secure the display hinges to the display panel
Where used: 2 screws that secure the Bluetooth module to the system board
Where used: 3 screws that secure the fan to the heat sink
94 Chapter 7 Screw listing
Download from Www.Somanuals.com. All Manuals Search And Download.
Phillips PM2.0×5.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
7
5.0 mm
2.0 mm
4.5 mm
Where used:
(1) Four captive screws that secure the hard drive cover to the computer
(2) Two captive screws that secures the memory module compartment cover to the computer
(3) One captive screw that secures the WLAN module compartment cover to the computer
Phillips PM2.0×5.0 captive screw 95
Download from Www.Somanuals.com. All Manuals Search And Download.
Where used: 2 screws that secure the top cover to the base enclosure
Where used: 2 screws that secure the modem module to the system board
Phillips PM2.5×4.0 screw 99
Download from Www.Somanuals.com. All Manuals Search And Download.
Phillips PM2.5×7.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
14
7.0 mm
2.5 mm
5.0 mm
Where used:
(1) One screw that secures the optical drive to the computer
(2) Three screws that secure the switch cover to the computer
(3) One screw that secures the display assembly to the computer
100 Chapter 7 Screw listing
Download from Www.Somanuals.com. All Manuals Search And Download.
Where used: 7 screws that secure the top cover to the base enclosure
Where used: 2 screws that secure the top cover to the base enclosure
Phillips PM2.5×7.0 screw 101
Download from Www.Somanuals.com. All Manuals Search And Download.
Phillips PM2.0×3.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
10
3.0 mm
2.0 mm
4.5 mm
Where used: 5 screws that secure the switch cover to the computer
Where used: 3 screws that secure the top cover to the base enclosure
Phillips PM2.0×3.0 screw 103
Download from Www.Somanuals.com. All Manuals Search And Download.
Where used: 2 screws that secure the front LED board to the base enclosure
104 Chapter 7 Screw listing
Download from Www.Somanuals.com. All Manuals Search And Download.
Where used: 4 screws that secure the display assembly to the computer
Torx T8M2.5×6.0 screw
Color
Quantity
Length
Thread
Heat diameter
Black
6
6.0 mm
2.5 mm
5.0 mm
Where used: 6 screws that secure the display bezel to the display assembly
106 Chapter 7 Screw listing
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Backup and recovery
Backup and recovery in Windows Vista
Creating recovery discs
After setting up the computer for the first time, be sure to create a set of recovery discs of the full factory
image. The recovery discs are used to start up (boot) the computer and recover the operating system and
software to factory settings in case of system instability or failure.
Note the following guidelines before creating recovery discs:
●
Use any of the following types of discs: CD-R, DVD+R, DVD+R DL, DVD-R, or DVD-R DL (purchased
separately). The discs you use will depend on the type of optical drive installed in your computer.
Because DVDs store more information than CDs, DVDs and DVDs with double-layer (DL) support
reduce the number of discs required.
NOTE: Read-write discs, such as CD-RW, DVD+RW, and DVD-RW, are not compatible with the
HP Backup & Recovery Manager software.
●
●
●
●
The computer must be connected to AC power during the process.
Only one set of the recovery discs can be created per computer.
Number each disc before inserting it into the optical drive of the computer.
If necessary, you can cancel the disc creation before you have finished creating the recovery discs.
The next time you select Create a set of recovery discs (Recommended), you will be
prompted to continue the disc creation.
To create a set of recovery discs:
1. Select Start > All Programs > HP Backup & Recovery > Backup & Recovery
Manager.
2. Click Next.
3. Click Create a set of recovery discs (Recommended), and then click Next.
Follow the on-screen instructions.
4.
Backing up your information
NOTE: You can only recover files that you have previously backed up. HP recommends that you use
HP Backup & Recovery Manager to create an entire drive backup as soon as you set up your computer.
Backup and recovery in Windows Vista 111
Download from Www.Somanuals.com. All Manuals Search And Download.
With HP Backup & Recovery Manager, you can perform the following tasks:
●
●
Backing up your information regularly to protect your important system files
Creating system recovery points that allow you to reverse undesireable changes to your computer
by restoring the computer to an earlier state
●
Scheduling backups at specific intervals or events
When to back up
●
On a regularly scheduled basis
NOTE: Set reminders to back up your information periodically.
Before the computer is repaired or restored
●
●
Before you add or modify hardware or software
Backup suggestions
●
Create a set of recovery discs using HP Backup & Recovery Manager.
●
Create system recovery points using HP Backup & Recovery Manager, and periodically copy them
to disc.
●
●
●
Store personal files in the Documents folder and back up these folders periodically.
Back up templates stored in their associated programs.
Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
Display the screen.
a.
b. Copy the screen.
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c. Open a word-processing document, and then select Edit > Paste.
NOTE: Before you can perform backup and recovery procedures, the computer must be connected to
external power.
NOTE: Drivers, utilities, and software installed by HP can be copied to a CD or to a DVD using HP
Backup & Recovery Manager.
Backing up specific files or folders
You can back up specific files or folders to the recovery partition on the hard drive, to an optional external
hard drive, or to optical discs (CDs or DVDs).
NOTE: This process will take several minutes, depending on the file size and the speed of the computer.
112 Chapter 8 Backup and recovery
Download from Www.Somanuals.com. All Manuals Search And Download.
To back up specific files or folders:
1. Select Start > All Programs > HP Backup & Recovery > Backup & Recovery
Manager.
2. Click Next.
3. Click Create or manage backups, and then click Next.
4. Click Back up user created files and folders, and then click Next.
Follow the on-screen instructions.
5.
Backing up the entire hard drive
When you perform a complete backup of the hard drive, you are saving the full factory image, including
the Windows® operating system, software, and all personal files and folders.
NOTE: A copy of the entire hard drive image can be stored on another hard drive, on a network drive,
or on recovery discs that you create.
NOTE: This process may take over an hour, depending on your computer speed and the amount of
data being stored.
To back up your entire hard drive:
1. Select Start > All Programs > HP Backup & Recovery > Backup & Recovery
Manager.
2. Click Next.
3. Click Create or manage backups, and then click Next.
4. Click Create or manage Entire Drive Backups, and then click Next.
5. Follow the on-screen instructions.
Backup and recovery in Windows Vista 113
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating recovery points
When you back up modifications since your last backup, you are creating system recovery points. This
allows you to save a snapshot of your hard drive at a specific point in time. You can then recover back
to that point if you want to reverse subsequent changes made to your system.
NOTE: The first system recovery point, a snapshot of the entire image, is automatically created the first
time you perform a backup. Subsequent recovery points make copies of changes made after that time.
HP recommends that you create recovery points at the following times:
●
●
Before you add or extensively modify software or hardware
Periodically, whenever the system is performing optimally
NOTE: Recovering to an earlier recovery point does not affect data files or e-mails created since that
recovery point.
To create a system recovery point:
1. Select Start > All Programs > HP Backup & Recovery > Backup & Recovery
Manager.
2. Click Next.
3. Click Create or manage backups, and then click Next.
4. Click Create or manage Recovery Points, and then click Next.
5. Follow the on-screen instructions.
Scheduling backups
Use HP Backup Scheduler to schedule backups for the entire system, for recovery points, or for specific
files and folders. With this tool, you can schedule backups at specific intervals (daily, weekly, or monthly)
or at specific events, such as at system restart or when you dock to an optional docking station (select
models only).
To schedule backups:
1. Select Start > All Programs > HP Backup & Recovery > HP Backup Scheduler.
2. Follow the on-screen instructions.
Performing a recovery
NOTE: You can only recover files that you have previously backed up. HP recommends that you use
HP Backup & Recovery Manager to create an entire drive backup as soon as you set up your computer.
HP Backup & Recovery Manager helps you with the following tasks for safeguarding your information
and restoring it in case of a system failure:
●
Recovering important files—This feature helps you reinstall important files without performing a full
system recovery.
●
Performing a full system recovery—With HP Backup & Recovery Manager, you can recover your full
factory image if you experience system failure or instability. HP Backup & Recovery Manager works
from a dedicated recovery partition on the hard drive or from recovery discs you create.
114 Chapter 8 Backup and recovery
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing a recovery from the recovery discs
To perform a recovery from the recovery discs, follow these steps:
Back up all personal files.
1.
2.
3.
Insert the first recovery disc into the optical drive and restart the computer.
Follow the on-screen instructions.
Performing a recovery from the hard drive
There are 2 ways to initiate a recovery from the hard drive:
●
●
From within Windows
From the recovery partition
Backup and recovery in Windows Vista 115
Download from Www.Somanuals.com. All Manuals Search And Download.
Initiating a recovery in Windows
To initiate a recovery in Windows, follow these steps:
1. Back up all personal files.
2. Select Start > All Programs > HP Backup & Recovery > Backup & Recovery
Manager.
3. Click Next.
4. Click Perform a recovery, and then click Next.
Follow the on-screen instructions.
5.
Initiating a recovery from the hard drive recovery partition
To initiate a recovery from the hard drive recovery partition, follow these steps:
Back up all personal files.
1.
2.
Restart the computer, and then press f11 before the Windows operating system loads.
3. Click a recovery option, and then click Next.
Follow the on-screen instructions.
4.
116 Chapter 8 Backup and recovery
Download from Www.Somanuals.com. All Manuals Search And Download.
Backup and recovery in Windows XP
Creating recovery discs
After setting up the computer for the first time, be sure to create a set of recovery discs of the full factory
image. The recovery discs are used to start up (boot) the computer and recover the operating system and
software to factory settings in case of system instability or failure.
Note the following guidelines before creating recovery discs:
●
Use any of the following types of discs: CD-R, DVD+R, DVD+R DL, DVD-R, or DVD-R DL (purchased
separately). The discs you use will depend on the type of optical drive installed in your computer.
Because DVDs store more information than CDs, DVDs and DVDs with double-layer (DL) support
reduce the number of discs required.
NOTE: Read-write discs, such as CD-RW, DVD+RW, and DVD-RW, are not compatible with the
HP Backup and Recovery Manager software.
●
●
●
●
The computer must be connected to AC power during the process.
Only one set of the recovery discs can be created per computer.
Number each disc before inserting it into the optical drive of the computer.
If necessary, you can cancel the disc creation before you have finished creating the recovery discs.
The next time you select Create factory software recovery CDs or DVDs to recover the
system (Highly recommended), you will be prompted to continue the disc creation.
To create a set of recovery discs:
1. Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery
Manager.
2. Click Next.
3. Click Create factory software recovery CDs or DVDs to recover the system (Highly
recommended), and then click Next.
Follow the on-screen instructions.
4.
Backing up your information
NOTE: You can only recover files that you have previously backed up. HP recommends that you use
HP Backup and Recovery Manager to create an entire drive backup as soon as you set up your computer.
With HP Backup and Recovery Manager, you can perform the following tasks:
●
●
Backing up your information regularly to protect your important system files
Creating system recovery points that allow you to reverse undesireable changes to your computer
by restoring the computer to an earlier state
●
Scheduling backups at specific intervals or events
Backup and recovery in Windows XP 117
Download from Www.Somanuals.com. All Manuals Search And Download.
When to back up
●
On a regularly scheduled basis
NOTE: Set reminders to back up your information periodically.
Before the computer is repaired or restored
●
●
Before you add or modify hardware or software
Backup suggestions
●
Create a set of recovery discs using HP Backup and Recovery Manager.
●
Create system recovery points using HP Backup and Recovery Manager, and periodically copy them
to disc.
●
●
●
Store personal files in the My Documents folder and back up these folders periodically.
Back up templates stored in their associated programs.
Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
a. Display the screen.
Copy the screen.
b.
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c. Open a word-processing document, and then select Edit > Paste.
NOTE: Before you can perform backup and recovery procedures, the computer must be connected to
external power.
NOTE: Drivers, utilities, and software installed by HP can be copied to a CD or to a DVD using HP
Backup and Recovery Manager.
Backing up specific files or folders
You can back up specific files or folders to the recovery partition on the hard drive, to an optional external
hard drive, or to optical discs (CDs or DVDs).
NOTE: This process will take several minutes, depending on the file size and the speed of the computer.
To back up specific files or folders:
1. Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery
Manager.
2. Click Next.
3. Click Back up to protect system settings and important data files, and then click
Next.
118 Chapter 8 Backup and recovery
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Click Back up individual files and folders, and then click Next.
Follow the on-screen instructions.
5.
Backing up the entire hard drive
When you perform a complete backup of the hard drive, you are saving the full factory image, including
the Windows® operating system, software, and all personal files and folders.
NOTE: A copy of the entire hard drive image can be stored on another hard drive, on a network drive,
or on recovery discs that you create.
NOTE: This process may take over an hour, depending on your computer speed and the amount of
data being stored.
To back up your entire hard drive:
1. Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery
Manager.
2. Click Next.
3. Click Back up to protect system settings and important data files, and then click
Next.
4. Click Back up entire hard drive, and then click Next.
Follow the on-screen instructions.
5.
Backup and recovery in Windows XP 119
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating recovery points
When you back up modifications since your last backup, you are creating system recovery points. This
allows you to save a snapshot of your hard drive at a specific point in time. You can then recover back
to that point if you want to reverse subsequent changes made to your system.
NOTE: The first system recovery point, a snapshot of the entire image, is automatically created the first
time you perform a backup. Subsequent recovery points make copies of changes made after that time.
HP recommends that you create recovery points at the following times:
●
●
Before you add or extensively modify software or hardware
Periodically, whenever the system is performing optimally
NOTE: Recovering to an earlier recovery point does not affect data files or e-mails created since that
recovery point.
To create a system recovery point:
1. Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery
Manager.
2. Click Next.
3. Click Back up to protect system settings and important data files, and then click
Next.
4. Click Create or manage Recovery Points, and then click Next.
Follow the on-screen instructions.
5.
Scheduling backups
Use HP Backup Scheduler to schedule backups for the entire system, for recovery points, or for specific
files and folders. With this tool, you can schedule backups at specific intervals (daily, weekly, or monthly)
or at specific events, such as at system restart or when you dock to an optional docking station (select
models only).
To schedule backups:
1. Select Start > All Programs > HP Backup & Recovery > HP Backup Scheduler.
2. Follow the on-screen instructions.
Performing a recovery
NOTE: You can only recover files that you have previously backed up. HP recommends that you use
HP Backup and Recovery Manager to create an entire drive backup as soon as you set up your computer.
HP Backup and Recovery Manager helps you with the following tasks for safeguarding your information
and restoring it in case of a system failure:
●
Recovering important files—This feature helps you reinstall important files without performing a full
system recovery.
●
Performing a full system recovery—With HP Backup and Recovery Manager, you can recover your
full factory image if you experience system failure or instability. HP Backup and Recovery Manager
works from a dedicated recovery partition on the hard drive or from recovery discs you create.
120 Chapter 8 Backup and recovery
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing a recovery from the recovery discs
To perform a recovery from the recovery discs, follow these steps:
Back up all personal files.
1.
2.
3.
Insert the first recovery disc into the optical drive and restart the computer.
Follow the on-screen instructions.
Performing a recovery from the hard drive
There are 2 ways to initiate a recovery from the hard drive:
●
●
From within Windows
From the recovery partition
Backup and recovery in Windows XP 121
Download from Www.Somanuals.com. All Manuals Search And Download.
Initiating a recovery in Windows
To initiate a recovery in Windows, follow these steps:
1. Back up all personal files.
2. Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery
Manager.
3. Click Next.
4. Click Recover important files or the entire system, and then click Next.
Follow the on-screen instructions.
5.
Initiating a recovery from the hard drive recovery partition
To initiate a recovery from the hard drive recovery partition, follow these steps:
Back up all personal files.
1.
2.
Restart the computer, and then press f11 before the Windows operating system loads.
3. Click a recovery option, and then click Next.
Follow the on-screen instructions.
4.
122 Chapter 8 Backup and recovery
Download from Www.Somanuals.com. All Manuals Search And Download.
External monitor
Pin
Signal
1
Red analog
2
Green analog
Blue analog
Not connected
Ground
3
4
5
6
Ground analog
Ground analog
Ground analog
+5 VDC
7
8
9
10
11
12
13
14
15
Ground
Monitor detect
DDC 2B data
Horizontal sync
Vertical sync
DDC 2B clock
124 Chapter 9 Connector pin assignments
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120
volts AC or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the country
or region where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or region
where the computer is used.
Requirements for all countries and regions
The requirements listed below are applicable to all countries and regions:
●
●
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
All power cord sets must be approved by an acceptable accredited agency responsible for evaluation
in the country or region where the power cord set will be used.
●
●
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating
of 125 or 250 V AC, as required by the power system of each country or region.
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard
Sheet C13 connector for mating with the appliance inlet on the back of the computer.
Requirements for all countries and regions 129
Download from Www.Somanuals.com. All Manuals Search And Download.
Requirements for specific countries and regions
Country/region
Accredited agency
Applicable note number
Australia
EANSW
OVE
1
1
1
2
1
1
1
1
1
3
4
1
1
5
1
1
4
1
2
Austria
Belgium
CEBC
CSA
Canada
Denmark
DEMKO
FIMKO
UTE
Finland
France
Germany
VDE
Italy
IMQ
Japan
METI
EK
Korea
The Netherlands
Norway
KEMA
NEMKO
CCC
SEMKO
SEV
The People's Republic of China
Sweden
Switzerland
Taiwan
BSMI
BSI
The United Kingdom
The United States
UL
1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding
type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug
must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4. The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and
wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be
used.
5. The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and
wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be
used.
130 Chapter 10 Power cord set requirements
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general household
waste. Follow the local laws and regulations in your area for computer battery disposal.
Display
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
CAUTION: The procedures in this appendix can result in damage to display components. The only
components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight.
Careful handling must be exercised when removing these components. When you remove these
components, handle them carefully.
NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly
that might require special handling at end-of-life. Disposal of mercury may be regulated because of
environmental considerations. For disposal or recycling information, contact your local authorities, or see
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight (1) and the liquid crystal display (LCD) panel (2).
NOTE: The procedures provided in this appendix are general disassembly instructions. Specific details,
such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from one
computer model to another.
Battery 131
Download from Www.Somanuals.com. All Manuals Search And Download.
Perform the following steps to disassemble the display assembly:
1. Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly.
2. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the
display bezel until the bezel disengages from the display assembly.
3. Remove the display bezel (3).
132 Chapter 11 Recycling
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Disconnect all display panel cables (1) from the display inverter and remove the inverter (2).
5. Remove all screws (1) that secure the display panel assembly to the display enclosure.
6. Remove the display panel assembly (2) from the display enclosure.
Turn the display panel assembly upside down.
7.
8. Remove all screws that secure the display panel frame to the display panel.
9. Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the display
panel frame.
Display 133
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Remove the display panel frame (2) from the display panel.
11. Remove the screws (1) that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover (2) and swing it outward.
13. Remove the backlight cover.
Turn the display panel right-side up.
14.
134 Chapter 11 Recycling
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Remove the backlight cables (1) from the clip (2) in the display panel.
16. Turn the display panel upside down.
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
Remove the backlight frame from the display panel.
17.
Display 135
Download from Www.Somanuals.com. All Manuals Search And Download.
18. Remove the backlight from the backlight frame.
19. Disconnect the display panel cable (1) from the LCD panel.
20. Remove the screws (2) that secure the LCD panel to the display rear panel.
21. Release the LCD panel (3) from the display rear panel.
22. Release the tape (4) that secures the LCD panel to the display rear panel.
Remove the LCD panel.
23.
Recycle the LCD panel and backlight.
24.
136 Chapter 11 Recycling
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
buttons
using 78
A
AC adapter, spare part
antennae
locations 5
info 7
audio-in jack
location 11
audio-out jack
power 7
connectors
presentation 7
TouchPad 6
wireless 7
power 12
C
location 11
Cable Kit
D
contents 21
diskette drive
precautions 30
display assembly
removal 51
display bezel
B
backup
components
modifications made to the
scheduling 114, 120
base enclosure screw cover,
illustrated 23
base enclosure, spare part
battery
bottom 14
buttons 7
display 5
front 11
keys 8
left-side 12
removal 53
display bezel, spare part
number 28
location 14
removal 37
lights 9
Display Cable Kit, spare part
number 28
right-side 13
switch 7
display enclosure
display enclosure, spare part
number 27
Bluetooth module
removal 61
Bluetooth module cable,
illustrated 21
top 6
computer feet
illustrated 23
locations 36
Computer Setup
accessing 77
display hinge
removal 54
Index 137
Download from Www.Somanuals.com. All Manuals Search And Download.
display inverter
locations 36
fingerprint reader board
inverter
removal 53
removal 53
J
display panel
jacks
audio-in 11
removal 54
drives
front LED board
audio-out 11
headphone 11
microphone 11
modem 12
network 12
RJ-11 12
removal 60
DVD-ROM Drive
precautions 30
removal 45
specifications 87
DVD/CD-RW Combo Drive
precautions 30
removal 45
RJ-45 12
G
grounding equipment and
methods 33
K
keyboard
H
hard drive
removal 47
location 14
precautions 30
removal 38
keys
specifications 86
esc 8
fn 8
specifications 85
hard drive cover
illustrated 22
function 8
keypad 8
E
ExpressCard assembly
removal 67
L
language, changing in Computer
Setup 81
legacy support, Universal Serial Bus
removal 38
headphone jack
location 11
heat sink
external media cards, product
description 3
external monitor port
location 13
lights
battery 9, 11
removal 73
hinge
F
fan
removal 54
removal 71
M
I
feet
mass storage devices, spare part
numbers 23
illustrated 23
138 Index
Download from Www.Somanuals.com. All Manuals Search And Download.
memory module
power requirements, product
description 3
processor
removal 40
Optical Drive Bezel/Bracket Kit,
removal 75
P
memory module compartment cover
illustrated 22
removal 40
microphone
passwords 80
product description
audio 2
chipset 1
pin assignments
illustrated 21
location 13
removal 64
Ethernet 2
graphics 1
keyboard 3
microphone 2
ports 3
processors 1
security 3
RJ-11 125
microphone jack
location 11
Miscellaneous Display Kit, spare
modem jack
location 12
modem module
S-Video-out 127
Universal Serial Bus (USB)
port 128
removal 69
Plastics Kit
contents 22
modem module cable,
illustrated 21
serviceability 4
wireless 2
pointing device components
illustrated 6
monitor port
location 13
TouchPad 6
R
recovery discs
N
ports
removal/replacement
preliminaries 29
procedures 35
restoring Computer Setup factory
settings 78
RJ-11 jack
network jack
location 12
monitor 13
O
operating system, product
description 3
optical drive
power cord
location 12
precautions 30
removal 45
location 12
Index 139
Download from Www.Somanuals.com. All Manuals Search And Download.
RJ-45 jack
location 12
RTC battery
system board
WLAN module
removal 65
removal 42
removal 58
WLAN module compartment cover
illustrated 22
removal 43
S
S-Video-out jack
location 13
Screw Kit
contents 93
serviceability, product
description 4
T
Thermal Material Kit, spare part
top cover
removal 55
TouchPad 6
speaker assembly
removal 62
speakers
specifications
U
Universal Serial Bus (USB) legacy
support 81
Universal Serial Bus (USB) port
computer 83
display 84
interrupts 89
V
vents 13, 14
switch cover
W
wireless antennae
disconnecting 44
locations 5
removal 49
140 Index
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|