LEFT-TILTING 10" TABLE SAW
MODEL G1023SL/G1023SLX
INSTRUCTION MANUAL
COPYRIGHT © FEBRUARY, 2003 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE
MACHINE CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF THE
MACHINE, THIS MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE . CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS
ABOUT DIFFERENCES. PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
PAGE
1.
2.
3.
SAFETY ........................................................................................................................................................................2
INSTRUCTIONS FOR POWER TOOLS ............................................................................................................2-3
ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS..............................................................................4
SAFETY ACCESSORIES ..................................................................................................................................5-6
COMMON DEFINITIONS, TERMS AND PHRASES ............................................................................................7
CIRCUIT REQUIREMENTS ..........................................................................................................................................8
220V SINGLE-PHASE ..........................................................................................................................................8
GROUNDING ........................................................................................................................................................8
EXTENSION CORDS ............................................................................................................................................9
WIRING..................................................................................................................................................................9
INFORMATION ............................................................................................................................................................10
COMMENTARY ..................................................................................................................................................10
UNPACKING........................................................................................................................................................11
PIECE INVENTORY ............................................................................................................................................12
CLEAN UP ..........................................................................................................................................................13
SITE CONSIDERATIONS....................................................................................................................................13
ASSEMBLY ................................................................................................................................................................ 14
EXTENSION WINGS ......................................................................................................................................14-15
SWITCH ..............................................................................................................................................................15
FENCE ................................................................................................................................................................15
MOTOR BRACE ..................................................................................................................................................16
GUARD BRACKET ..............................................................................................................................................16
HANDWHEEL ......................................................................................................................................................17
TABLE INSERT....................................................................................................................................................17
DUST PORT ........................................................................................................................................................18
SAW BLADE ........................................................................................................................................................18
BLADE GUARD/SPLITTER ............................................................................................................................18-20
ADJUSTMENTS ..........................................................................................................................................................21
BLADE HEIGHT ..................................................................................................................................................21
BLADE TILT ........................................................................................................................................................21
MITER SLOT TO BLADE................................................................................................................................22-23
BLADE ALIGNMENT ......................................................................................................................................24-25
RIP FENCE ..........................................................................................................................................................25
MITER GAUGE ....................................................................................................................................................25
OPERATIONS..............................................................................................................................................................26
PRE-RUN CHECK ..............................................................................................................................................26
TEST RUN ..........................................................................................................................................................27
BLADE SELECTION ......................................................................................................................................27-29
CROSSCUTTING ................................................................................................................................................29
RIPPING ..............................................................................................................................................................30
DADO OPERATIONS ....................................................................................................................................31-32
RABBET OPERATIONS ................................................................................................................................32-33
MAINTENANCE ..........................................................................................................................................................34
TABLE AND WINGS............................................................................................................................................34
V-BELTS ........................................................................................................................................................34-35
LUBRICATION ....................................................................................................................................................35
MAINTENANCE NOTES......................................................................................................................................36
CLOSURE....................................................................................................................................................................37
MACHINE DATA ..................................................................................................................................................38
PARTS BREAKDOWNS AND LIST................................................................................................................39-43
TROUBLESHOOTING ........................................................................................................................................44
PUSH STICK PATTERN......................................................................................................................................45
WARRANTY AND RETURNS ........................................................................................................................46-47
4.
5.
6.
7.
8.
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
For Your Own Safety Read Instruction
Manual Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words which are intended to convey the level of
importance of the safety messages. The progression of symbols is described below. Remember
that safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the equipment.
NOTICE
Safety Instructions For Power Tools
1. KEEP GUARDS IN PLACE and in working
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors should
be kept a safe distance from work area.
order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning on.
6. MAKE WORKSHOP CHILD PROOF
with padlocks, master switches, or by
removing starter keys.
3. KEEP WORK AREA CLEAN. Cluttered
7. DO NOT FORCE TOOL. It will do the job
better and safer at the rate for which it
was designed.
areas and benches invite accidents.
4. DO NOT USE IN DANGEROUS ENVI-
RONMENT. Do not use power tools in
damp or wet locations, or where any flam-
mable or noxious fumes may exist. Keep
work area well lighted.
8. USE RIGHT TOOL. Do not force tool or
attachment to do a job for which it was
not designed.
-2-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions For Power Tools
9. USE PROPER EXTENSION CORD. Make
sure your extension cord is in good condi-
tion. Conductor size should be in accor-
dance with the chart below. The amperage
rating should be listed on the motor or tool
nameplate. An undersized cord will cause
a drop in line voltage resulting in loss of
power and overheating. Your extension
cord must also contain a ground wire and
plug pin. Always repair or replace exten-
sion cords if they become damaged.
16. REDUCE THE RISK OF UNINTENTION-
AL STARTING. On machines with mag-
netic contact starting switches there is a
risk of starting if the machine is bumped
or jarred. Always disconnect from power
source before adjusting or servicing.
Make sure switch is in OFF position before
reconnecting.
17. MANY WOODWORKING TOOLS CAN
“KICKBACK” THE WORKPIECE toward
the operator if not handled properly. Know
what conditions can create “kickback” and
know how to avoid them.
Minimum Gauge for Extension Cords
LENGTH
AMP RATING
0-6
25ft
16
16
16
14
12
10
50ft 100ft
18. CHECK DAMAGED PARTS. Before fur-
ther use of the tool, a guard or other part
that is damaged should be carefully
checked to determine that it will operate
properly and perform its intended func-
tion. Check for alignment of moving parts,
binding of moving parts, breakage of
parts, mounting, and any other conditions
that may affect its operation. A guard or
other part that is damaged should be
properly repaired or replaced.
16
16
16
12
12
10
16
14
14
12
10
No
7-10
11-12
13-16
17-20
21-30
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get
caught in moving parts. Non-slip footwear
is recommended. Wear protective hair cov-
ering to contain long hair.
19. NEVER LEAVE TOOL RUNNING UNAT-
TENDED. TURN POWER OFF. Do not
leave tool until it comes to a complete
stop.
11. ALWAYS USE SAFETY GLASSES. Also
use face or dust mask if cutting operation is
dusty. Everyday eyeglasses only have impact
resistant lenses, they are NOT safety glasses.
20. NEVER OPERATE A MACHINE WHEN
TIRED, OR UNDER THE INFLUENCE
OF DRUGS OR ALCOHOL. Full mental
alertness is required at all times when
running a machine.
12. SECURE WORK. Use clamps or a vise to hold
work when practical. It’s safer than using your
hand and frees both hands to operate tool.
21. NEVER ALLOW UNTRAINED PERSON-
NEL TO OPERATE THE MACHINE
WHILE UNSUPERVISED. Make sure any
instructions you give in regards to
machine operation are approved, correct,
safe, and clearly understood.
13. DO NOT OVER-REACH. Keep proper
footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for lubri-
cating and changing accessories.
22. IF AT ANY TIME YOU ARE EXPERI-
ENCING DIFFICULTIES performing the
intended operation, stop using the
machine! Then contact our service
department or ask a qualified expert how
the operation should be performed.
15. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recom-
mended accessories. The use of improper
accessories may cause risk of injury.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions For Table Saws
8. NEVER use the miter gauge and rip fence
at the same time. Move the rip fence out of
the way when crosscutting.
1. ALWAYS use blade guard, splitter and
anti-kickback fingers on all ''through-saw-
ing'' operations. Through-sawing opera-
tions are those when the blade cuts com-
pletely through the workpiece as in ripping
or crosscutting.
9. NEVER attempt to free a stalled saw blade
without first turning the saw OFF.
10. PROVIDE adequate support to the rear
and sides of the saw table for wide or long
workpieces.
2. AVOID KICKBACKS. A condition in which
a piece of wood is thrown back towards an
operator at a high rate of speed. If you do
not have a complete understanding of how
kickback occurs, or how to prevent it, DO
NOT operate this table saw.
11. AVOID awkward operations and hand
positions where a sudden slip could cause
your hand to move into the blade.
3. ALWAYS hold the work firmly against the
miter gauge or fence while holding down
against the table.
12. IF AT ANY TIME YOU ARE EXPERIENC-
ING DIFFICULTIES performing the intend-
ed operation, stop using the machine!
Then contact our service department or
ask a qualified expert how the operation
should be performed.
4. ALWAYS use a push-stick for ripping nar-
row stock.
5. NEVER perform any operation ''free-hand''
which means using only your hands to
support or guide the workpiece. Always
use either the fence or the miter gauge to
position and guide the work.
13. ALWAYS LOWER OR REMOVE SAW
BLADE WHEN NOT IN USE.
14. NEVER USE A DAMAGED SAW BLADE
OR ONE THAT HAS BEEN DROPPED.
6. NEVER stand or have any part of your
15. DADO AND RABBET OPERATIONS
PRESENT SPECIFIC DANGER because
those operations must be performed with
the blade guard removed. Be especially
aware of your personal safety whenever
operating saw with the guard removed,
and always immediately replace the blade
guard after these operations are complete.
body in line with the path of the saw blade.
7. NEVER reach behind or over the blade
with either hand while the saw is running. If
kickback occurs, that hand will be pulled
into the spinning blade.
Like all power tools, there is danger asso-
ciated with table saws. Accidents are fre-
quently caused by lack of familiarity or fail-
ure to pay attention. Use this tool with
respect and caution to lessen the possibil-
ity of operator injury. If normal safety pre-
cautions are overlooked or ignored, serious
personal injury may occur.
No list of safety guidelines can be com-
plete. Operating this machinery may require
additional safety precautions specific to
your shop environment. Failure to use rea-
sonable caution while operating this
machine could result in serious personal
injury.
-4-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Accessories
Statistics prove that most common acci-
dents among table saw users can be
linked to kickback. Kickback is typically
defined as the high-speed expulsion of
stock from the table saw toward its opera-
tor. In addition to the danger of the opera-
tor or others in the area being struck by
the flying stock, it is often the case that
the operator’s hands are pulled into the
blade during the kickback. The following
can help minimize kickbacks.
Push Sticks
The use of push sticks, particularly when cutting
small or narrow workpieces, provides a double
benefit for saw operators. The push stick pro-
vides added leverage, enabling the operator to
keep the workpiece firmly supported against the
fence and the table. At the same time, the push
stick keeps the operator’s hand safely away from
the rotation of the saw blade. See the template at
the end of the manual for construction details, or
purchase one from the Grizzly catalog. See
Figure 1.
1. Use your blade guard and splitter.
2. Never, for any reason, place your hand
behind the blade. Should kickback
occur, your hand will be pulled into the
blade.
3. Inspect for alignment along the splitter
and your blade.
4. Never use the fence as a guide for
crosscutting.
5. Never attempt freehand cuts.
6. Use a pushstick or featherboard to main-
tain control of your workpiece.
7. Feed cuts through to completion.
8. Stand to the side when ripping.
9. Ensure that your fence and your miter
slot are parallel to the blade.
If you do not have a clear understanding of
kickback and how it occurs, do not operate
this table saw.
Figure 1. Push Stick.
Zero Clearance Table Inserts
Ideal for use when ripping thin strips or making
bevel cuts, zero clearance table inserts prevent
tear-out and jammed blades by supporting mate-
rial that is close to the blade. Use the standard
table insert as a template when creating addition-
al inserts from wood or plywood. Blade slot
inserts can be custom cut for specific blade
angles by raising the running blade into an uncut
insert at the angle you desire. Be sure to make an
additional slot for the blade splitter. There are
also a wide selection of table inserts in the Grizzly
catalog. Clamp the insert firmly in place with a
piece of wood when creating slots. Never hold the
table insert with your hand while cutting new
slots. See Figure 2 for examples of zero clear-
ance table inserts.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Featherboards
Easily made from scrap stock, featherboards pro-
vide an added degree of protection against kick-
back. To make a featherboard, cut a 30-40° angle
at one end of the board, and make a number of
1
end cuts at approximately ⁄4" apart and 2" to 3"
deep. There are a number of featherboards in the
Grizzly catalog. See Figure 4.
Figure 2. Zero Clearance Table Inserts
Push Paddles
Push paddles (shown in Figure 3) provide added
leverage and support when ripping or crosscut-
ting wide workpieces. There are a number of
push paddles in the Grizzly catalog.
Figure 4. Featherboards
Figure 3. Push Paddles
-6-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Definitions, Terms and Phrases
The following is a list of common definitions, terms and phrases used throughout this manual as they relate
to this table saw and woodworking in general. Becoming familiar with these terms is important before
assembling, adjusting or operating this machine. Your safety is VERY important to us at Grizzly!
Arbor: Metal shaft extending from the drive
Non-Through Cut: A sawing operation that
requires the removal of the blade guard and
splitter. Dado and rabbet cuts are considered
Non-Through Cuts because the blade does not
protrude above the top face of the wood stock.
Always remember to reinstall the blade guard
and splitter after performing a non-through cut.
mechanism, to which cutting blade is attached.
Bevel Edge Cut: Tilting the saw arbor and blade
to an angle between 0° and 45° to perform an
angled cutting operation.
Blade Guard: Metal or plastic mechanism that
mounts over the saw blade to prevent acciden-
tal contact with the cutting edge.
Perpendicular: Intersecting and forming right
angles; at right angles to the vertical and hori-
zontal planes. i.e. the blade is perpendicular to
the table surface.
Crosscut: Table saw operation in which the miter
gauge is used to cut across the grain of a piece
of wood.
Push Paddle: Safety aid used to push a piece of
wood stock through a cutting operation.
Dado Blade: Blade or set of blades that attach to
the arbor and are used for cutting grooves and
rabbets.
Push Stick: Safety aid used to push a piece of
wood stock through a cutting operation.
Usually used when rip cutting.
Dado Cut: Table saw operation that uses a dado
blade to cut a flat bottomed groove into the
face of wood stock.
Rabbet: Cutting operation that creates an L-
shaped channel along the edge of wood stock.
Featherboard: Safety device used to keep a
board against the rip fence or table. Allows
operator to keep hands away from the saw
blade.
Splitter: Metal plate attached to the back of the
blade guard that maintains the kerf opening in
the wood when performing a cutting operation.
1
Standard Kerf: ⁄8" gap made with a standard
Kerf: The resulting cut or gap made by a saw
blade.
blade.
Straightedge: A tool used to check the flatness,
Kickback: An event in which the wood is thrown
back toward an operator at a high rate of
speed.
parallelism, or consistency of a surface(s).
Through Cut: A sawing operation in which the
wood stock thickness is completely sawn
Miter Gauge: A component that controls the
wood stock movement while performing a
crosscut. Allows for variation of angle cuts
such as miter cuts used on a picture frame.
through. Proper blade height usually allows 1⁄4
"
of the top of the blade to extend above the
wood stock.
Thin Kerf: 3⁄32" gap made with a thin kerf blade.
Rip Cut: A cut made along the grain of the wood.
Moulding Head: A cutterhead attached to the
arbor. Accepts interchangeable moulding
knives for profile cutting. We DO NOT recom-
mend the use of moulding heads because they
require advanced skills for their operation.
Sacrificial Fence: A piece of wood attached to
the face of the rip fence that is designed to
extend the fence face away from the metal por-
tion of the fence. Used primarily when making
rabbet cuts with a dado blade.
Parallel: Being an equal distance apart at every
point. i.e. the rip fence face is parallel to the
side face of the saw blade.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: CIRCUIT REQUIREMENTS
220V Single-Phase
Grounding
In the event of a malfunction or breakdown,
grounding provides electric current a path of least
resistance to reduce the risk of electric shock.
This tool is equipped with an electric cord having
an equipment-grounding conductor which must
be properly connected to a grounding plug. The
plug must be plugged into a matching outlet that
is properly installed and grounded in accordance
with all local codes and ordinances.
The Model G1023SL/G1023SLX Left-Tilting 10"
Table Saw has a 3 HP, 3450 RPM motor which
requires a 220V single-phase circuit. The cord set
included does not have a plug, as the style of plug
you require will depend upon the type of service
you currently have or plan to install. The motor will
safely draw about 18 amps at 220V under load. If
you operate the Model G1023SL/G1023SLX on
any circuit that is already close to its capacity, it
might blow a fuse or trip a circuit breaker.
However, if an unusual load does not exist, and
power failure still occurs, have the circuit inspect-
ed by a qualified electrician.
Improper connections of the electrical-grounding
conductor can result in risk of electric shock. The
conductor with green or green and yellow striped
insulation is the electrical-grounding conductor. If
repair or replacement of the electric cord or plug
is necessary, do not connect the equipment
grounding conductor to a live terminal.
In
preparing
to
connect
the
Model
G1023SL/G1023SLX to your existing or new cir-
cuit, connect a plug that matches your 220V
receptacle as long as it is rated to 20 amps or
more. If you will be installing a new receptacle and
plug, we recommend using a NEMA-style 6L-20
plug and outlet shown in Figure 5.
This equipment must be
grounded. Verify that any
existing electrical outlet
and circuit you intend to
plug into is actually
grounded. Under no cir-
cumstances should the
grounding pin from any
three-pronged plug be
removed. Serious injury
may occur.
The Model G1023SL/G1023SLX should be fused
at 20 amps. Fusing at amperage ratings higher
than 20 amps will not adequately protect the cir-
cuit. Also be sure that the wiring in your circuit is
rated to handle 20 amps.
Figure 5. 220V Single-Phase
-8-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Extension Cords
Wiring
We do not recommend the use of extension cords
on 220V equipment. Instead, arrange the place-
ment of your equipment and the installed wiring to
eliminate the need for extension cords. Should it
be necessary to use an extension, make sure the
cord is rated Standard Service (grade S) or bet-
ter. Refer to the chart in Section 1: Safety to
determine the minimum gauge for the extension
cord. The extension cord must also contain a
ground wire and plug pin. Always repair or
replace extension cords when they become worn
or damaged.
Always utilize a qualified electrician when doing
any electrical work on this equipment.
We have covered some basic electrical
requirements for the safe operation of your
machine. These requirements are not neces-
sarily comprehensive. You must be sure
that your particular electrical configuration
complies with local and state codes. Ensure
compliance by checking with your local
municipality or a licensed electrician.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: INTRODUCTION
Most importantly, we stand behind our machines.
Commentary
If you have any service questions or parts
requests, please call or write us at the location
listed below.
We are proud to offer the Grizzly Model
G1023SL/G1023SLX Left-Tilting 10" Table Saw.
The Model G1023SL/G1023SLX is part of a
growing Grizzly family of fine woodworking
machinery. When used according to the guide-
lines set forth in this manual, you can expect
years of trouble-free, enjoyable operation and
proof of Grizzly’s commitment to customer satis-
faction.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
The specifications, drawings, and photographs
illustrated in this manual represent the Model
G1023SL/G1023SLX as supplied when the man-
ual was prepared. However, owing to Grizzly’s
policy of continuous improvement, changes may
be made at any time with no obligation on the part
of Grizzly. Whenever possible, though, we send
manual updates to all owners of a particular tool
or machine. Should you receive one, we urge you
to insert the new information with the old and
keep it for reference.
The Model G1023SL and the Model G1023SLX
are the same machines with different fence rail
combinations. Specifically, the Model G1023SL
features the Shop Fox Classic fence with stan-
dard rails, and the Model G1023SLX features the
Shop Fox Classic fence with extension rails and
an extension table.
The Model G1023SL/G1023SLX is an industrial
grade table saw intended for professional use.
Features include cast iron trunnions, 4" dust port,
triple V-belt drive, magnetic switch, and a 3 HP,
220V, single-phase motor.
Read the manual before
assembly and opera-
tion. Become familiar
with the machine and its
operation before begin-
ning any work. Serious
personal injury may
result if safety or opera-
tional information is not
understood or followed.
All running parts operate on sealed ball bearings
and require no maintenance for the life of the
bearings. We also offer many accessories for the
table saw including blades, outfeed rollers, a slid-
ing table and a mobile base. Please refer to our
current catalog for prices and ordering informa-
tion.
We are also pleased to provide this manual with
the Model G1023SL/G1023SLX. It was written to
guide you through assembly, review safety con-
siderations, and cover general operating proce-
dures. It represents our effort to produce the best
documentation possible. If you have any com-
ments regarding this manual, please write to us at
the address below:
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
-10-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Make sure your floor
structure is capable of
supporting the combined
weight of the machine
parts and the people.
The Model G1023SL/G1023SLX base unit is
shipped from the manufacturer in a carefully
packed carton. If you discover the machine is
damaged after you have signed for delivery,
immediately call our Customer Service for advice.
NOTICE
The fence (and extension table kit, if applicable)
will arrive in a separate box.
Save all containers and packing materials
until you are satisfied that your Model
G1023SL/G1023SLX has arrived in good
condition. Freight company adjusters will
want to inspect those materials in the event
that a freight claim must be made.
When you are completely satisfied with the con-
dition of your shipment, you should inventory its
parts.
The G1023SL/G1023SLX
is a heavy machine, 430
lbs. shipping weight.
DO NOT over-exert
yourself while unpack-
ing or moving your
machine – you will need
assistance and power
equipment. Serious per-
sonal injury may occur
if safe moving methods
are not followed.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Piece Inventory
After all the parts have been removed from their
containers, you should have:
• Table Saw Unit (Figure 6)
• Miter Gauge
• Extension Wings (2)*
• Fence Assembly
• Splitter/Guard Assembly
• Dust Port
• Table Insert
• Dado Insert
• Cabinet Cover
Figure 8. G1023SL component layout.
• Arbor Wrench
• Support Shaft
The hardware bag should contain the following:
• Handwheel and Handle
• Switch Brace
• Hardware Bag
• (1) 3mm Allen® Wrench
• (1) 4mm Allen® Wrench
• (1) Flat Head Screw 5⁄16"-18 x 11⁄2
"
• (1) Combo Wrench 5⁄8
• (2) Hinge Pins
"
* The Model G1023SLX comes with only (1)
extension wing.
• (2) Hex Bolt 5⁄16"-18 x 11⁄2
• (2) Hex Bolt 5⁄16"-18 x 1"
• (3) Hex Nut 5⁄16"-18
"
• (7) Flat Washers 5⁄16"
• (2) Lock Washer 5⁄16"
• (2) Setscrew 5⁄16"-18 x 3⁄8
"
In the event that any nonproprietary parts are
missing (e.g. a nut or a washer), we would be
glad to replace them; or for the sake of expedien-
cy, replacements can be obtained at your local
hardware store.
Note: A full component and hardware breakdown
of the Shop Fox® Classic fence can be found in
the manual that accompanies the fence. Those
items are not included in this manual.
G1023SL/G1023SLX base unit.
Figure 6.
-12-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Clean up
Site Considerations
1. Floor
Load:
Your
Model
The table and other unpainted parts of the Model
G1023SL/G1023SLX are coated with a waxy
grease that protects them from corrosion during
shipment. Clean this grease off with a solvent
cleaner or citrus-based degreaser such as
Grizzly’s G7895 Degreaser. Do not use chlorine-
based solvents – if you happen to splash some
onto a painted surface, you will ruin the finish.
G1023SL/G1023SLX represents a large
weight load in a small footprint. Most com-
mercial floors are suitable for the saw. Some
residential floors may require additional
bracing to support both machine and opera-
tor.
2. Working Clearances: Consider existing and
anticipated needs, size of material to be
processed through each machine, and
space for auxiliary stands, work tables or
other machinery when establishing a loca-
tion for your table saw.
Do not use gasoline or
other petroleum-based
solvents to clean with.
They have low flash
points which make them
extremely flammable. A
risk of explosion and
burning exists if these
products are used.
Serious personal injury
may occur.
3. Lighting and Outlets: Lighting should be
bright enough to eliminate shadows and pre-
vent eye strain. Electrical circuits should be
dedicated or large enough to handle amper-
age requirements. Outlets should be located
near each machine so power or extension
cords are clear of high-traffic areas. Observe
local electrical codes for proper installation
of new lighting, outlets, or circuits.
Do not smoke while using
solvents. A risk of explo-
sion or fire exists and may
result in serious personal
injury.
Make your shop “child
safe.” Ensure that your
workplace is inaccessible
to youngsters by closing
and locking all entrances
when you are away. Never
allow visitors in your shop
when assembling, adjust-
ing or operating equip-
ment.
Many of the solvents
commonly used to clean
machinery can be toxic
when inhaled or ingest-
ed. Always work in well-
ventilated areas far from
potential ignition sources
when dealing with sol-
vents. Use care when dis-
posing of waste rags and
towels to be sure they do
not create fire or environ-
mental hazards.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: ASSEMBLY
Extension Wings
Keep clothing rolled up
and out of the way of
machinery and keep
hair pulled back.
Inspect the extension wings for burrs or foreign
material that may inhibit assembly. The mating
edges of the wings and the table must be clean,
smooth, and flat. Use a wire brush or file if nec-
essary to clean up the edges. For the Model
G1023SLX, only follow the left wing instructions.
Disconnect power to the
machine when perform-
ing any maintenance or
assembly. Failure to do
this may result in serious
personal injury.
The table and the wings
represent a very heavy
load. DO NOT over-exert
yourself while lifting or
moving the table and the
wings – get assistance.
1. Attach the left wing to the table using the
three hex head bolts and the flat washers
provided. Adjust the wing reasonably flush
with the table. Do not tighten the bolts.
Wear safety glasses dur-
ing the entire assembly
process. Failure to com-
ply may result in serious
personal injury.
2. Attach the right wing to the table using the
three hex head bolts and the flat washers
provided. Adjust the wing reasonably flush
with the table. Do not tighten the bolts.
Some metal parts may
have sharp edges on
them after they are
formed. Please examine
the edges of all metal
parts before handling
them. Failure to do so
could result in injury.
3. Align the top of the wing flush with the table
top directly above the front bolt, and tighten
the front bolt. The front edge of the extension
wing should also be flush with the front edge
of the table.
4. Raise or lower the rear of the extension wing
until the middle of the wing is flush with the
table top. Tighten the middle bolt.
Most of your Model G1023SL/G1023SLX has
been assembled at the factory, but some parts
must be assembled or installed after delivery. We
have organized the assembly process into steps.
Please follow along in the order presented here.
5. Raise or lower the rear of the wing until the
wing and table are flush. Tighten the bolt.
Any adjustment at this point should be mini-
mal.
6. Check flushness over the front bolt and re-
TOOLS REQUIRED: You will need a high quality
square, a long straightedge, 10mm, 12mm,
14mm open end wrenches and a 3mm Allen®
wrench.
adjust if necessary.
7. Repeat Steps 3-4 for the other extension
wing.
-14-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Now, check the alignment of the table and
both wings with a straightedge. The straight-
edge should run flat across both wings and
the table top. If the straightedge contacts
both wings and the table evenly, you are fin-
ished with this section. If the straightedge
does not contact them evenly, continue to
Step 9.
Switch
The switch comes prewired to the motor and can
be easily mounted to the table through the holes
in the extension wing.
To mount the switch:
9. If the extension wings tilt up or down at the
outside edges, remove the wings and shim
them with masking tape similar to Figure 9.
1. Line the switch bracket holes up with the
holes in the extension wing on the backside
of the edge.
a. If the wings tilt down, stick layers of mask-
ing tape under each bolt near the bottom
edge of the wing and retighten.
2. Use the 5⁄16"-18 Phillips® flat head screw and
nut to attach the switch to the extension wing
as shown in Figure 10.
b. If the wing tilts up, stick layers of masking
tape above each bolt near the top edge of
the wing and retighten. Allow the tape to
extend above table surface and trim with
a sharp knife after final assembly.
3. Mount the switch brace between the lower
switch screw and the table screw.
10. Replace the wings and check again.
Figure 10. Installing switch.
Masking Tape
Figure 9. Using tape to shim for wing alignment.
Fence
Your Model G1023SL/G1023SLX comes with a
Shop Fox® Classic fence. For fence assembly
instructions, refer to the manual provided with the
fence.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
Motor Brace
The motor brace shown in Figure 11 has been
installed for shipping purposes. Please remove
this brace before continuing with assembly. The
bolts that secure the brace should be screwed
back in at the locations from which they came.
Figure 12. Attaching guard support shaft.
3. Slide the lower half of the bracket onto the
splitter shaft and temporarily tighten the
setscrews.
4. Place the upper bracket half on the lower
half and secure both halves with the bolts
nuts and four washers as shown in Figure
13. Do not fully tighten the nuts at this
moment.
Figure 11. Motor Brace.
Guard Bracket
To install the guard support shaft:
1. Place the threaded end of the shaft through
the hole in the back of the saw (Figure 12).
Figure 13. Splitter bracket installed.
2. Thread the shaft into the tilt assembly.
-16-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Ensure that all four setscrews are firmly in
Handwheel
contact with the table casting.
3. Using a 6mm hex wrench, raise or lower
each of the four setscrews shown in Figure
15 until the insert is flush with the table top.
Use a straightedge to make sure the table
insert is flush with the top of the table.
One handwheel has been removed for shipping.
To install, place the handwheel over the threads
and screw the lock knob into the center. Next
insert the handle into the handwheel and tighten
it as shown in Figure 14. Install the other handle
onto the other handwheel.
4. Now make sure the blade will not come into
contact with the table insert. Position the
blade at 90°, then raise and lower the blade
through its full range of motion. Also, rotate
the blade, making sure that the blade never
contacts any part of the table insert. Do the
same with the blade in the 45° position. Wear
leather gloves while rotating the blade to pre-
vent being cut.
NOTICE
The table insert must be flush with the top
of the table or the workpiece will hit the
edge of the table insert at the beginning of
the cut.
Figure 14. Installing handle on handwheel.
Table Insert
Disconnect power to the
machine when perform-
ing any maintenance,
assembly or adjust-
ments. Failure to do this
may result in serious
personal injury.
Figure 15. Setscrews on each corner of insert.
The table insert provides access to the blade and
the arbor when removed. When in place, the
insert provides support for the materials being
cut.
1. Disconnect the power cord from the outlet!
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
Dust Port
4. Replace the outer arbor flange and rethread
the arbor nut onto the arbor.
Mount the the dust port onto the cabinet stand
with the 4 Phillips® screws as shown in Figure
16.
5. Hand tighten the nut and snug with the
wrench included with the saw. DO NOT
overtighten.
IMPORTANT: Make sure the blade is installed
with the teeth facing the front of the saw.
Blade Guard/Splitter
1. Slip the blade guard/splitter over the mount-
ing bolts as shown in Figure 17. The wash-
ers should be between the bolt head and the
slots. Tighten the bolts to secure the blade
guard/splitter.
Figure 16. Dust port installed on cabinet.
Blade Guard
Saw Blade
Anti-kickback Pawl
The saw blade is extremely sharp. Use extra
care when handling the blade or working
near it. Serious injury is possible.
Mounting Bolts
Figure 17. Blade guard and splitter in place.
Please review this section even if your saw blade
came pre-installed. To install the blade:
2. Set a machinist’s square against the face of
the blade splitter. Slightly rotate the rear
bracket to adjust the face of the blade splitter
perpendicular to the table top as shown in
Figure 18.
1. Remove the table insert to gain access to the
arbor.
2. Remove the nut and the outer arbor flange
from the arbor.
3. Place the blade on the arbor, making sure
that it seats firmly against the inner arbor
flange. Ensure that the top blade teeth are
facing the front of the saw.
-18-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
4. If the blade splitter is to the right of the blade
as shown in Figure 20, simply add washers
between the splitter and the front mounting
bracket, and adjust the rear splitter support
as shown in Figure 21.
Figure 18. Blade splitter square to table.
The saw blade is extremely sharp. Use extra
care when handling the blade or working
near it. Serious injury is possible.
3. Next, set a straightedge against the face of
the saw blade and the blade splitter as
shown in Figure 19. If the blade splitter is
properly aligned, please skip ahead to the
“Table Insert” instructions; otherwise, contin-
ue with the next step.
Figure 20. Improper splitter/blade alignment.
Figure 21. Proper splitter/blade alignment.
Figure 19. Guard in line with blade.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Recheck the splitter alignment to the blade
and to the table top. Adjust as necessary and
tighten all the bolts before use. If the blade
guard is properly aligned, please skip ahead
to step 10; otherwise, continue with the next
step.
Adjustment Bolt
6. If the splitter is positioned to the left of the
blade, alignment cannot be achieved by
washer placement. Adjustment of the front
support bracket is required. See Figure 21
for adjustment details. Loosen the (2) adjust-
ment screws and move left or right.
Arbor Bracket
Figure 22. Arbor bracket adjustment locations.
7. If this adjustment does not allow enough
movement of the splitter, remove the table
and wings, and set them to one side.
9. Moving the arbor bracket moves the V-belts
and pulleys out of alignment, so adjustment
of the motor pulley is required. Simply loosen
the setscrew in the middle groove of the pul-
ley, and slowly slide the pulley toward the
end of the motor shaft. Once the V-belts are
back in alignment, tighten the setscrew
securely.
The table and wings
represent a very heavy
load. DO NOT over-
exert yourself while lift-
ing or moving the table
and wings – get assis-
tance.
10. Recheck the guard alignment to the blade
and to the table top. Adjust as necessary and
tighten down all the bolts before use. If the
blade guard is properly aligned, re-attach the
table, making sure there is adequate blade
clearance through all blade adjustments.
8. The arbor bracket and motor pulley needs
adjusting. Loosen the adjustment bolt shown
in Figure 22, and slowly slide the arbor
bracket towards the end of the shaft. Only
move the arbor bracket a distance equal to
the amount of misalignment between the
blade and the splitter, or a little more. You
can always adjust the splitter back to the left
with washers. Tighten the adjustment bolt
securely.
11. Adjust the blade to 45°. Raise and lower it
through the full range. Re-adjust the blade to
90°, then raise and lower it through the full
range. There should be no contact between
the blade, the base, the table insert, or any
other part of the saw. If there is contact,
repeat steps 7-9.
-20-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: ADJUSTMENTS
Blade Tilt
Disconnect power to the
machine when perform-
ing any maintenance,
assembly or adjust-
ments. Failure to do this
may result in serious
personal injury.
1. Set your blade angle at zero as shown on the
angle indicator on the front of the saw and
raise the blade several inches above the
table.
2. Place a machinist’s square flat on the table
and slide it alongside the blade. The square
should contact the blade evenly from bottom
to top. Make sure that a blade tooth does not
obstruct the movement of the square.
Keep loose clothing
rolled up and out of the
way of machinery and
keep hair pulled back.
3. Adjust the handwheel until the square is
flush with the blade. Loosen the tilt indicator
arrow, set to zero, and retighten. Loosen and
adjust the stop bolt on the left side of the
front trunnion to allow a 90° stop point. See
Figure 23 for details.
Wear safety glasses
during the entire adjust-
ment process. Failure
to comply may result in
serious personal injury.
4. Turn the blade angle handwheel until the
angle indicator points at the desired angle.
5. Tighten the handwheel locking knob.
6. Repeat Steps 1-6 for setting the blade to 45°
and adjust the 45° stop bolt on the right side
of the front trunnion. Use the 45° side of a
combo square or a bevel gauge set at 45°.
Blade Height
When preparing to operate your table saw, you
should adjust the blade height to approximately
90° Stop Bolt
1
⁄4" above the surface of the material you plan on
cutting. The handwheel at the front of the saw
adjusts the blade height. To adjust the blade
height:
1. Loosen the locking knob at the center of the
45° Stop Bolt
blade height handwheel.
2. Using a sample of the material you plan on
cutting as a gauge, turn the handwheel until
the blade reaches its intended height.
3. Retighten the locking knob.
Figure 23. Geared trunnion.
4. Recheck your blade height with the sample
material and re-adjust, if necessary.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
6. If the blade tip does not touch the end of the
adjustable square similar to the first mea-
surement, then the table will need to be
adjusted.
Miter Slot to Blade
Your table saw will give the best results if the
miter slot and the rip fence are adjusted parallel
to the blade. If either of these are not exactly par-
allel, your cuts and your finished work will be
lower in quality, but more important, this condition
increases the risk of kickback. Take the time to
adjust your table saw properly. A few minutes
now will be time well spent.
7. To adjust the table, loosen the four bolts in
the table mounting locations (see Figure 25)
and slightly tap the table. Repeat Steps 1-5
until satisfactory. Do not forget to tighten the
table mounting bolts when finished.
1. Disconnect plug from power source.
2. Use an adjustable square to measure the
distance from the miter slot to a carbide tip
on the blade as shown in Figure 24. Make
sure that the face of the adjustable square is
even along the miter slot.
Table Mounting Locations
3. With the end of the adjustable square just
touching the tip, lock the square in place.
Now, mark the carbide tip with a magic mark-
er where you made this measurement.
Figure 25. Table mounting bolt holes.
4. Rotate that tip to the other end of the table
insert.
8. Now check to see if the blade remains paral-
lel to the miter slot when tilted to 45°.
5. Slide the adjustable square down to the
other end of the table insert, and compare
the distance from the marked blade tip to the
end of the adjustable square.
9. Tilt the blade to 45° and repeat Steps 1-5. If
the blade is still parallel to the miter slot, con-
tinue on to the “Miter Gauge” instructions.
Otherwise, continue with the next step.
10. If the blade was parallel to the miter slot at
90° but not at 45°, the table will need to be
shimmed with metal shim stock. The shims
are placed under the table over each of the
four table mounting bolts.
The saw blade is dangerously sharp. Use
extra care when handling the blade or
working near it. Serious injury is possible.
Figure 24. Adjusting blade to miter slot.
-22-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Refer to Figures 26 and 27, for shim place-
ment. If the distance of A is shorter than B,
shim(s) will need to be placed under corners
#1 and #2. If the distance of B is shorter than
A, shim(s) will need to be placed under cor-
ners #3 and #4. Very thin shim stock works
well, just make sure they are all the same
thickness, and you put an equal number
under each of the two corners.
12. Tighten down one bolt a small amount and
then move on to each of the others, tighten-
ing each down the same amount. Continue
to rotate through the bolts, tightening them a
little each time until they are all secure.
Figure 26. Shim procedure diagram A.
13. Now recheck the blade to miter slot at 90°
and 45° by repeating Steps 1-5. If the dis-
tance of A and B are equal, continue to the
“Miter Gauge” instructions. If the distances
are still off, repeat Steps 9-12.
14. Once you feel you have the miter slot adjust-
ed to the blade, recheck all measurements
and be sure the table mounting bolts are
secure. Repeat Step 10 in Section 4:
Assembly, “Blade Guard/Splitter.” Also, if
you ever remove the table in the future, be
sure to make note of shim placements and
reassemble exactly how it came apart.
Figure 27. Shim procedure diagram B.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Reattach the table, making sure there is ade-
quate blade clearance through all blade
adjustments. Recheck guard alignment to
the blade and to the table top. Adjust as nec-
essary and tighten down all the bolts before
use.
Blade Alignment
The blade position can be adjusted slightly in
case it contacts the table insert when raised or
tilted. This adjustment can be made either by
moving the whole trunnion assembly, or by just
moving the arbor bracket. Try adjusting by mov-
ing the whole trunnion first, this is the easier of
the two ways.
5. If the blade is still contacting the insert,
repeat Steps 1-4. Check all other adjust-
ments.
6. Recheck the blade to miter slot adjustments,
and adjust as necessary.
To adjust the blade position by moving the
trunnion:
1. Disconnect plug from power source.
Adjustment Bolt
2. Remove the table and wings and set them to
one side.
3. Loosen the four trunnion mounting bolts as
shown in Figure 28, and nudge to either the
left or the right depending on where the
blade is hitting the saw.
Arbor Bracket
Figure 29. Adjusting arbor bracket.
To adjust the blade position by moving the
arbor bracket:
1. Disconnect plug from power source.
2. Remove the table and wings and set them to
one side.
3. Loosen the adjustment bolt shown in Figure
29.
Figure 28. Trunnion mounting bolts.
4. To adjust the arbor bracket, loosen the
adjustment bolt. Slowly slide the arbor brack-
et towards the end of the shaft.
The table and wings rep-
resent a very heavy
load. DO NOT over-
exert yourself while lift-
ing or moving the table
and wings – get assis-
tance.
NOTICE
If you make the adjustment described in
this section, check and adjust the blade
splitter to make sure it aligns with the
blade.
-24-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Moving the arbor bracket moves the V-belts
and pulleys out of alignment, so adjustment
of the motor pulley is required. Simply loosen
the setscrew in the middle motor groove pul-
ley and slowly slide the pulley towards the
end of the motor shaft. Once the V-belts are
back in alignment, tighten the setscrew
securely.
2. Adjust the miter body until there is no space
between the square and the blade. Tighten
the lock knob.
3. With the stop link in the up position, loosen
the jam nut and adjust the stop screw until it
is seated against the stop link. See Figure
30 for part locations.
6. Reattach the table, making sure there is ade-
quate blade clearance through all blade
adjustments. Recheck guard alignment to
the blade and to the table top. Adjust as nec-
essary and tighten down all the bolts before
use.
4. Now loosen the setscrew on the left front
side of the miter bar, adjust the pointer to 90°
and tighten the setscrew.
5. To adjust to 45°, follow Steps 1-4 using an
adjustable square set to 45°.
7. If the blade is still contacting the insert,
repeat Steps 1-6. Check all other adjust-
ments.
6. After rotating the miter body from 45° to 90°
and back a few times, double-check your
adjustments at both angles to assure that
you have accurately set your miter gauge.
8. Recheck the blade to miter slot adjustments,
and adjust as necessary.
The miter bar can be adjusted so that it fits tighter
in the miter slot. To do this, turn the adjustment
setscrew shown in Figure 30 clockwise. Turn the
adjustment setscrew in small increments at a
time so you do not over-adjust the miter bar.
Rip Fence
The rip fence included with your Model
G1023SL/G1023SLX Left-Tilting 10" Table Saw
is designed to provide excellent ripping accuracy
when properly adjusted. For complete adjustment
procedures, refer to the manual that is included
with the fence.
Jam Nut
Pointer
Stop Link
Adjustment
Setscrew
Stop Screw
Setscrew
Miter Gauge
Figure 30. Miter gauge diagram
To adjust the miter gauge so it is perpendicu-
lar to the saw blade:
1. Loosen the lock knob on the miter gauge and
place a square against the face of the miter
body and the blade.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: OPERATIONS
Pre-Run Check
Keep loose clothing out
of the way of machinery
and keep hair pulled
back.
Before you begin to use your Model
G1023SL/G1023SLX Left-Tilting 10" Table Saw,
you should give it a thorough inspection. While
making your inspection, ask yourself the follow-
ing questions:
1. Are all the fasteners tight?
2. Is the blade mounted correctly?
3. Is the saw stable?
Disconnect power to the
machine when perform-
ing any adjustments or
maintenance. Failure to
do this may result in seri-
ous personal injury.
4. Is it wired properly?
5. Is your electrical system properly config-
ured?
Wear safety glasses dur-
ing all operations on the
shaper. Failure to com-
ply may result in serious
personal injury.
6. Have you checked your workpiece for obvi-
ous defects?
7. Are the V-belts properly tensioned and the
pulleys properly aligned?
8. Is the guard assembly installed and func-
tional?
Always wear
a
dust
mask when operating
the table saw. Using this
machine produces saw-
dust which may cause
allergic reactions or res-
piratory problems.
9. Have you checked the saw blade clearance
when it is adjusted to varying angles and
depths?
10. Have you read all the warnings and direc-
tions regarding the operation of this
machine?
NOTICE
The following section was designed to give
instructions on the basic operations of this
table saw. However, it is in no way compre-
hensive of every table saw application. There
are many different jigs that can be built to
increase safety, accuracy, and types of cuts.
WE STRONGLY RECOMMEND that you read
books, trade magazines, or get formal train-
ing to maximize the potential of your table
saw.
-26-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Test Run
Blade Selection
1. Face the table saw and stand to the left of
Choosing the correct blade for the job is essential
for the safe and efficient use of your table saw.
Ignoring this important step could result in dam-
age to the saw and serious injury to the operator.
Below are the most common saw blades and
their uses.
the blade path.
2. With one finger on the START button and
one finger on the STOP button, turn the saw
on. Be ready to turn the saw off in case of a
mishap.
1. Rip Blade (shown in Figure 31): Used for
cutting with the grain. Typically, 10" rip
blades have between 20-40 teeth, a flat-top
ground profile (see Figure 32 for saw tooth
profiles) and large gullets to allow for large
chip removal.
3. Watch and listen to the saw. Note whether
there are any unusual sounds or excessive
vibrations.
4. If anything appears abnormal, immediately
turn off the saw, unplug it, and fix the prob-
lem. If a problem exists that is beyond the
scope of this manual, call our service depart-
ment.
5. If the saw is behaving normally, turn it off and
prepare to make a cut according to the
instructions outlined in this section.
Figure 31. Ripping blade.
Figure 32. Various saw tooth cutting profiles.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Cross-cut Blade: Used for cutting across
the grain. 10" cross-cut blades have
between 60-80 teeth, alternate top bevel or
steep alternate top bevel tooth profiles, small
hook angle and a shallow gullet. See Figure
33.
Figure 34. Combination blade.
4. Plywood Blade: Used for cutting plywood or
veneers. A 10" plywood blade will have 40-
80 teeth, a steep alternate top bevel tooth
profile and very shallow gullet. See Figure
35.
Figure 33. Cross-cutting blade.
3. Combination Blade: Used for cutting with
and across the grain. A compromise
between a rip blade and a cross-cut blade, a
10" combination blade will typically have
between 40-50 teeth, an alternate top bevel
and flat or alternate top bevel and raker
tooth profile. The teeth are arranged in
groups of five. The gullets are small and
shallow within the groups of five teeth, simi-
lar to a cross-cut blade; then large and deep
between the groups, like a ripping blade.
See Figure 34.
Figure 35. Plywood blade.
-28-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Thin-kerf: Most types of saw blades are
available in a thin-kerf style. Designed pri-
marily to minimize stock waste, thin-kerf
blades be used in conjunction with a blade
stabilizer to reduce blade wobble. Note:
Most blade guards/splitters are thicker than
most thin-kerf blades. Make sure that the
stock will pass by the guard/splitter before
beginning a cut.
2. Inspect the miter gauge. Is it properly set and
tight? Move the rip fence completely out of
the way.
3. Turn on the saw and allow it to come to full
speed.
4. Hold the workpiece firmly against the face of
the miter gauge and ease it into the blade
(See Figure 36) and through the workpiece.
6. Dado Blades: There are two types of dado
blades: stack and wobble. Stack dadoes are
expensive and time consuming to set up but
leave a clean and smooth finish. Stack
dadoes are used for fine furniture and cabi-
net making. Wobble dadoes are inexpensive
and easy to set up, but leave a rough finish.
5. Turn off the saw and allow the blade to come
to a full stop.
7. Moulding Heads: A moulding head is a cut-
terhead that attaches to the arbor and holds
individual moulding knives. We do not rec-
ommend their use. They are very dangerous
and required training beyond the scope of
this manual.
This section on blade selection is by no means
comprehensive. Always follow the saw blade
manufacturer's recommendations to assure safe
and efficient operation of your table saw.
Figure 36. Cross-cut operation.
Small cutoff pieces can contact the moving
blade and be thrown back toward the oper-
ator. Always use the least amount of clear-
ance between the table insert and the blade
to reduce the risk of injury from these
pieces. Never attempt to grab these pieces
while the table saw is turned on. Your hand
may come into contact with the blade. Turn
the table saw off and safely remove these
pieces AFTER the blade has come to a com-
plete stop or use a long scrap piece of wood
to carefully move them away from the spin-
ning blade.
Crosscutting
Crosscutting means cutting across the grain of
the wood. In wood products without grain (i.e.
MDF, particleboard) crosscutting simply means
cutting across the width of the stock.
Crosscuts are made with the miter gauge. There
are two miter gauge slots in the table top. Use the
one that works best for the piece being crosscut.
To make a crosscut using the miter gauge:
1. Inspect the board for soundness. You do not
necessarily need a square edge to crosscut
with accuracy.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Turn on the saw and allow it to reach full
speed. Place the trued edge of the board
against the rip fence. Feed the workpiece
slowly and evenly into the blade and through
the workpiece. Do not stand behind the
board as shown in Figure 37.
Ripping
Ripping means to cut with the grain of the wood.
In other materials such as MDF or plywood, rip-
ping simply means to cut lengthwise. To rip a
board:
1. Inspect the board for soundness. You will
need a straightedge to rip with accuracy.
Your workpiece may need to be jointed flat
before attempting to cut on the table saw.
Never attempt to rip a board that does not
have one perfectly straight edge on it.
Always run the straight edge of the board
against the rip fence. Failure to do this
could result in kickback and serious per-
sonal injury.
Figure 37. Do not stand directly behind wood!
2. Set the rip fence to the desired distance from
the blade. IF YOU ARE MAKING NARROW
CUTS, USE A PUSH-STICK. Serious injury
can occur if you put your hands close to the
blade. A push-stick pattern has been includ-
ed in this manual on Page 45, or you can
purchase the G3445 or G1411 push stick
from the Grizzly catalog. Use them to hold
the workpiece against the table and fence,
and push the workpiece fully past the blade.
When a small width is to be ripped and a
push-stick cannot be safely put between the
blade and rip fence, rip a larger piece to
obtain the desired piece.
Stand out of the line of potential kickback.
Hold the workpiece firmly against the fence
and table. Do not allow your fingers to get
close to the blade! Do not reach over the
blade to off-load the workpiece.
-30-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Dado Operations
Always use push sticks, featherboards,
push paddles and other safety accessories
whenever possible to increase safety and
control during operations which require the
blade guard and splitter to be removed from
the saw. ALWAYS replace the blade guard
after dadoing is complete.
In addition to its ability to rip and crosscut lumber,
the table saw is also an invaluable tool for creat-
ing a variety of dadoes. These non-through cuts
can be created with a regular saw blade or with
specially-designed stacking or wobbling dado
blades. See Figure 38.
Proper dado operations will differ depending on
the blade system you choose. Consult the
instructions included with your dado blades for
directions regarding attachment and adjustment.
To use a dado blade:
1. Ensure that the saw is switched off and dis-
connected from its power source.
2. Remove the table insert, splitter guard, and
regular saw blade.
3. Attach and adjust the dado blade system as
recommended in the dado blade’s instruc-
tions.
Figure 38. Optional dado blade system.
4. Install the dado table insert.
Never allow hands or arms to be above or
behind the saw blade. Should kickback
occur, the hands and arms can be pulled
into the saw blade. Serious injury will result.
5. Raise the blade system up to the desired
depth of the dado. Make sure the dado blade
will not cut through the work piece.
6. If dadoing along the length of your work-
piece, adjust the distance between the fence
and the inside edge of the blade to suit your
needs. When cutting across the wood grain,
use the miter gauge as a guide while dado-
ing. Remember: never use the fence as a
stop in conjunction with your miter gauge.
Never perform a through cut operation with
a dado blade. A dado blade was designed
to make non-through cuts only. Failure to
follow these directions could result in seri-
ous injury will result.
7. Reconnect the saw to the power source.
Dado operations present very real hazards
requiring proper procedures to avoid seri-
ous injury. The chance of kickback is
always greater when dado blades are used
so extra precautions must be used. Any
movement of the stock away from the fence
will cause kickback. Be certain that stock is
flat and straight. Failure to follow these
warnings could result in serious personal
injury.
8. Using a scrap as a test piece, switch on the
saw and take a pass over the dado blade.
9. If the cut is satisfactory, repeat with your fin-
ish stock.
10. Re-install the blade guard.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-31-
Download from Www.Somanuals.com. All Manuals Search And Download.
Dadoing operations can also be accomplished
using a conventional saw blade. To create a sin-
gle-blade dado:
Rabbet Operations
1. Clearly mark the width of the dado cut on
your workpiece. Include marks on the edge
of your workpiece so you can clearly identify
your intended cut while the material is laying
flat on the saw table.
In addition to its ability to create a variety of
dadoes, this table saw can be used to cut L-
shaped rabbets. These cuts can be created with
a regular saw blade or with specially-designed
stacking or wobbling dado blades like the one
shown in Figure 38.
2. Set the blade height to the depth of cut you
wish to create.
Proper rabbet operation will differ depending on
the blade system you choose. Consult the
instructions included with your dado blades for
directions regarding attachment and adjustment.
To use a dado blade for rabbeting operations:
3. If the dado runs the length of the material,
adjust the fence so the blade is aligned with
the inside of your dado channel. See Figure
39.
1.
Rabbet cutting on the edge of a piece of
stock requires the use of a sacrificial fence
attachment. See Figure 40. The sacrificial
4. Turn on your saw and make the first cut.
fence can be made from a piece of wood
3
that is as long as the metal fence and ⁄4
"
thick. Once the sacrificial fence has been
cut, attach it to the metal fence with screws
or clamps, making sure they are all secure
and tight.
Rip Fence
Sacrificial Fence
Dado Insert
Figure 39. Single-blade dado cut.
Blade Cut-Out
5. Turn off the saw and re-adjust the fence so
the blade is aligned with the other edge of
the intended dado channel. Be sure to keep
the cuts within your marks; otherwise, your
dado will be too large.
Figure 40. Sacrificial fence.
6. Turn on the saw and make a second cut.
7. Move toward the center of the dado with your
Always use push sticks, featherboards,
push paddles and other safety accessories
whenever possible to increase safety and
control during operations which require
that the blade guard and splitter must be
removed from the saw. ALWAYS replace the
blade guard after dadoing is complete.
subsequent cuts until the dado is complete.
8. Re-install the blade guard.
-32-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Ensure that the saw is switched off and dis-
Rabbeting operations can also be accomplished
using a conventional saw blade. To create a sin-
gle-blade rabbet:
connected from its power source.
3. Remove the table insert, splitter guard and
the regular saw blade from the arbor.
1. Clearly mark the width of the rabbet cut on
your workpiece. Include marks on the edge
of your workpiece so you can clearly identify
your intended cut while the material is laying
flat on the saw table.
4. Attach and adjust the dado blade system as
recommended in the dado blade’s instruc-
tions. Raise the blade system according to
your needs. Make sure it will not cut through
the workpiece.
2. Set the blade height to the depth of cut you
wish to create.
5. If rabbeting along the length of your work-
piece, adjust the distance between the fence
and the outside edge of the blade to suit your
needs. See Figure 41. When cutting across
the wood grain, use the miter gauge as a
guide while rabbeting. Remember: never
use the fence as a stop in conjunction with
your miter gauge.
3. If the rabbet runs the length of the material,
adjust the fence so the blade is aligned with
the inside of your rabbet channel.
4. Turn on your saw and make the first cut.
5. Turn off the saw and re-adjust the fence so
that the next cut will remove another portion
of the wood stock between the inside edge of
the rabbet and the edge of the wood.
6. Using a scrap as a test piece, switch on the
saw and take a pass over the dado blade.
7. If the cut is satisfactory, repeat with your fin-
6. Turn on the saw and make a second cut.
ish stock.
7. Continue to re-adjust the blade and cut until
8. Re-install the blade guard.
the entire rabbet is made.
8. Re-install the blade guard.
Instructions on using moulding heads have
been intentionally left out. They are very
dangerous when not used properly.
Considerable skill and training beyond the
scope of this manual are required to safely
operate a moulding head. Serious personal
injury could result if this caution is not fol-
lowed.
Figure 41. Rabbet cutting.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-33-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7: MAINTENANCE
General
V-Belt
Regular periodic maintenance on your Model
G1023SL/G1023SLX will ensure its optimum per-
formance. Make a habit of inspecting your
machine each time you use it. Check for the fol-
lowing conditions and repair or replace when
necessary:
To ensure optimum power transmission from the
motor to the blade, the V-belts must be in good
condition and operate under the proper tension.
When replacing V-belts, replace all three at the
same time —even if they do not all appear worn.
Belt tension should be checked at least every 3
months; more often if using the table saw inten-
sively.
1. Guard alignment and operation.
2. Worn switch.
The V-belts are accessed through the cavity on
the right side of the saw. They link the arbor and
motor pulleys. To check V-belt tension:
3. Worn or damaged cords and plugs.
4. Damaged V-belt.
1. With moderate pressure, push the center of
5. Loose mounting bolts.
6. Inspect blades for damage.
each V-belt.
2. Note the amount of deflection. Deflection
1
should be approximately ⁄2", similar to
7. Any other condition that could hamper the
Figure 42.
safe operation of this machine.
Tables
The nonpainted surfaces on the Model
G1023SL/G1023SLX should be protected
against rust and pitting. Wiping the machine
clean after every use ensures that wood dust is
not allowed to trap moisture against bare metal
surfaces.
Figure 42. Belt deflection.
Tables can be kept rust-free with regular applica-
tions of products like SLIPIT®. For long term stor-
age you may want to consider products like
Boeshield T-9™.
Disconnect power to the
machine when perform-
ing any maintenance or
repairs. Failure to do this
may result in serious
personal injury.
-34-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
To adjust V-belt tension:
Lubrication
1. Loosen the motor mount bolt.
2. Shift the motor up or down to increase or
decrease the V-belt tension. Tighten the
motor mount bolt.
Lubricate the areas indicated below every 12
months.
1. Blade angling trunnions. These should be
lubricated with 6 or 7 drops of light machine
oil.
3. Check the V-belt tension again. Ensure that
the motor pulley and arbor pulley are lined
up.
2. Blade height trunnion. This should also be
lubricated with 6 or 7 drops of light machine
oil.
To replace the V-belts:
1. Remove the blade.
3. The two (2) worm gears should be lubricat-
2. Adjust the arbor so it is up all the way and in
ed with an automotive wheel bearing grease.
the 90° position.
These points can be reached by removing the
table. Check all adjustments when finished lubri-
cating.
3. Place a board under the motor and loosen
the motor mount bolt. Slowly lower the arbor
until the motor rests on the board, allowing
the belts to be loose on the pulleys.
4. Pull off the old V-belts and replace them with
new ones. Have the number from the belt
ready when calling the service department
for replacements.
5. Raise the arbor and remove the board to
adjust the V-belt tension.
6. Tighten the motor mount bolt.
Keep clothing rolled
up and out of the way
of machinery and keep
hair pulled back.
Wear safety glasses dur-
ing the entire mainte-
nance process. Failure
to comply may result in
serious personal injury.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-35-
Download from Www.Somanuals.com. All Manuals Search And Download.
3 HP
SINGLE-PHASE
220V POWER SOURCE
Magnetic Switch
SDN TYPE
G1023SL/G1023SLX
A
L1/1
L2/3
L3/5
7
B
T1/2
1/2
T2/4
3/4
T3/6
8
5/6
18
26
22
98
96
95
MOTOR
-36-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8: CLOSURE
The following pages contain general machine
We recommend you keep a copy of our current
catalog for complete information regarding
Grizzly's warranty and return policy. If you need
additional technical information relating to this
machine, or if you need general assistance or
replacement parts, please contact the Customer
Service Department listed in the introduction.
data, troubleshooting guide, parts diagram, parts
list and Warranty/Return information for your
Model G1023SL/G1023SLX Left-Tilting 10" Table
Saw.
If you need parts or help in assembling your
machine, or if you need operational information,
we encourage you to call the Customer Service
Department. Our trained service technicians will
be glad to help you.
Additional information sources are necessary to
realize the full potential of this machine. Trade
journals, woodworking magazines, and your local
library are good places to start.
If you have comments dealing specifically with
this manual, please write to our Bellingham,
Washington location using the address in the
Introduction. The specifications, drawings, and
photographs illustrated in this manual represent
the Model G1023SL/G1023SLX as supplied
when the manual was prepared. However, due to
Grizzly’s policy of continuous improvement,
changes may be made at any time with no oblig-
ation on the part of Grizzly. Whenever possible,
though, we send manual updates to all owners of
a particular tool or machine. Should you receive
one, add the new information to this manual and
keep it for reference.
Operating this equipment has the potential
for flying debris to cause eye injury. Always
wear safety glasses or goggles when oper-
ating equipment. Everyday glasses or read-
ing glasses only have impact resistant lens-
es, they are not safety glasses. Be certain
the safety glasses you wear meet the appro-
priate standards of the American National
Standards Institute (ANSI).
We have included some important safety mea-
sures that are essential to this machine’s opera-
tion. While most safety measures are generally
universal, Grizzly reminds you that each work-
shop is different and safety rules should be con-
sidered as they apply to your specific situation.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-37-
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901
GRIZZLY MODEL G1023SL/G1023SLX
LEFT-TILTING 10" TABLE SAW
Overall Dimensions:
Table Size ..................................................................................401⁄8" x 27" w/Wings
Stand ..........................................................................Cabinet Style, Powder Coated
Overall Height ....................................................................................................403⁄4
"
Overall Width........................................................................................................56"
Overall Depth ......................................................................................................34"
Base Dimension ................................................................................201⁄2" W x 201⁄2" D
Weight ..........................................................................................................430 lbs
Capacities:
Blade Tilt ..................................................................................................0˚-45˚ Left
Maximum Blade Diameter......................................................................................10"
Maximum Width Of Cut ........................................................................................26"
Maximum Depth Of Cut @ 90° ................................................................................3"
Maximum Depth Of Cut @ 45°..............................................................................21⁄8
Maximum Dado Width ..........................................................................................13⁄16"
"
Motor:
Type ..........................................................................TEFC Capacitor Start Induction
Size ..................................................................................................................3 HP
Phase ⁄ Cycle ............................................................................Single-Phase ⁄ 60 Hz
Amps ....................................................................................................................18
Voltage..............................................................................................................220V
Speed (RPM) ....................................................................................................3450
Power Transfer ..............................................................................Triple V-Belt Drive
Bearings..............................................................Shielded & Lubricated Ball Bearings
Switch ......................................................................................Heavy Duty Magnetic
Arbor:
Arbor Size ............................................................................................................5⁄8
Arbor Speed ..............................................................................................4200 RPM
"
Features:
..............................................................(G1023SL) Shop Fox® Classic Fence With Standard Rails
..........................................(G1023SLX) Shop Fox Classic Fence With Extension Rails and Table
..................................................................................................................Extra Large Handwheels
............................................................................................Two Table Inserts for Blade and Dado
......................................................................................................................................Miter Gauge
............................................................................................................................Ground Table Top
........................................................................................................................Powder Coated Paint
-38-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-39-
Download from Www.Somanuals.com. All Manuals Search And Download.
-40-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-41-
Download from Www.Somanuals.com. All Manuals Search And Download.
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
01 P1023SL001 CABINET
01A P1023SL001A LOWER PANEL
02 P1023SL002 SCALE
30A PSB08
30B P1023SL030B SPACER
31 PB03
CAP SCREW 5⁄16"-18 X 11⁄2
"
HEX BOLT 5⁄16"-18 X 1
03 PHTEK4
04 P1023SL004 MOTOR COVER
05 P1023SL005 CORD CONNECTOR
06A PS01
06B PN07
07 P1023SL007 LATCH
07A P1023SL007A STRIKE
08 P1023SL008 LOCK KNOB
09 P1023SL009 HANDLE
10 P1023SL010 HANDWHEEL
11 PSS15
12 PSB65
12A PLW03
13 P1023SL013 POINTER BRACKET
14 PS35
PHLP HD SCRW 5⁄16"-18 X 3⁄8
15 P1023SL015 POINTER
16 P1023SL016 FRNT TRUNNION BRACKET
16A P1023SL016A GUIDE BLOCK
TAP SCREW 10-24 X 10L
32 P1023SL032 FLANGE
33 P1023SL033 SHAFT
35 P1023SL035 GEAR BEARING HOUSING
PHLP HD SCRW 10-24 X 1⁄2
HEX NUT 10-24
"
36 PSB26
37A PLW04
37B PK03
38 P6203
39 PR23M
CAP SCREW 3⁄8"-16 X 11⁄2
"
LOCK WASHER 3⁄8
"
KEY 1⁄4" X 1⁄4" X 45L
BEARING 6203 ZZ
SNAP RING 40MM
40 P1023SL040 ARBOR NUT
41 P1023SL041 COLLAR
SETSCREW 3⁄8"-16 X 3⁄8
"
CAP SCREW 10-24 X 2"
LOCK WASHER 3⁄16"
42 P1023SL042 ARBOR PULLEY
43 PSS11
43A PSS07
44 PK02M
SETSCREW 1⁄4"-20 X 1⁄4
"
"
SETSCREW 1⁄4"-20 X 1⁄2
KEY 5 X 5 X 40L
"
45 P1023SL045 BLADE ARBOR
46 P1023SL046 BLADE (NOT INCLUDED)
47 P1023SL047 ARBOR FLANGE
48 P1023SL048 ARBOR NUT
49 P1023SL049 COLLAR
50 P1023SL050 MOTOR FRAME SUPPORT
51 P1023SL051 CLIP
16B PSB05
16C PW06
16D P1023SL016D COLLAR
CAP SCREW 1⁄4"-20 X 3⁄4
"
FLAT WASHER 1⁄4
"
17 P1023SL017 SHIELD PLATE
52 P1023SL052 PIVOT PIN
PHLP HD SCRW 5⁄16"-18 X 3⁄4
"
53 PSB14
54 PVM26
CAP SCREW 3
⁄
8"-16 X 1"
18 PS35
19 PSB26
20 PLW04
21 PN08
22 PSS03
CAP SCREW 3⁄8"-16 X 11⁄2
"
V-BELT, SET OF 3
LOCK WASHER 3⁄8
HEX NUT 3⁄8"-16
"
55 P1023SL055 MOTOR PULLEY
56 P1023SL056 MOTOR 3 HP
56A P1023SL056A MOTOR PLATE
SETSCREW 1⁄4"-20 X 3⁄8
"
57 PB15
57A PW07
HEX BOLT 5⁄16"-18 X 3⁄8
"
"
23 P1023SL023 WORM GEAR
24 P1023SL024 COLLAR
FLAT WASHER 5⁄16"
25 PSS05
SETSCREW 5⁄16"-18 X 1⁄4
"
58 P1023SL058 CORD CLAMP
26 P1023SL026 TILT SHAFT
26A P1023SL026A BRASS WASHER 3⁄4
27 P1023SL027 PIN
27A P1023SL027A BEARING LOAD SPRING
28 PK15M KEY 5 X 5 X 35L
58A P1023SL058A CORD CLAMP PLATE
58B P1023SL058B CORD CLAMP PLATE
"
60 PB07
61 PW07
HEX BOLT 5⁄16"-18 X 3⁄4
FLAT WASHER 5⁄16"
62 P1023SL062 BRACKET
29A P1023SL029A GEARED TRUNNION
29B P1023SL029B BUSHING
30 PN02
63A P1023SL063A REAR TRUNNION
63B P1023SL063B BUSHING
HEX NUT 5⁄16"-18
64 P1023SL064 ROLL PIN 5⁄16"-1"
-42-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
CAP SCREW 3⁄8"-16 X 1"
99 PB32
HEX BOLT 5⁄16"-18 X 5⁄8
"
65 PSB14
66 PLW04
68 P1023SL068 SHAFT
104 P1023SL104 FLAT WASHER 3⁄16"
LOCK WASHER 3⁄8
"
106 PW02
140 PB11
141 PW07
142 PLW01
143 PN02
144 PB03
145 PSS02
FLAT WASHER 3⁄8
"
HEX BOLT 5⁄16"-18 X 11⁄2
FLAT WASHER 5⁄16"
LOCK WASHER 5⁄16"
HEX NUT 5⁄16"-18
"
69 PN03
HEX NUT 3⁄4"-16
70 P1023SL070 REAR TRUNNION BRACKET
72 P1023SL072 SHAFT
73 P1023SL073 UPPER GUARD BRACKET
74 P1023SL074 LOWER GUARD BRACKET
HEX BOLT 5⁄16"-18 X 1"
SETSCREW 5⁄16"-18 X 3⁄8
"
79 PSS07
SETSCREW 1 4"-20 X 1⁄2
⁄ "
154 P1023SL154 SWITCH PLATE BRACE
155 P1023SL155 MOTOR BRACE
211 P1023SL211 LOGO PLATE
80 P1023SL080 STANDARD TABLE INSERT
80A P1023SL080A DADO TABLE INSERT
80B P1023SL080B SPRING CLIP
80C PS06
81 P1023SL081 TABLE
PHLP HD SCREW 10-24 X 3⁄8
"
212 P1023SL212 DISCONNECT PWR LABEL
213 P1023SL213 SAFETY GLASSES LABEL
214 P1023SL214 SELF TAPPING SCREW
82 PLW04
83 PB24
LOCK WASHER 3⁄8
"
216 P1023SL216 COMBO WRENCH 5⁄8
217 P1023SL217 ARBOR WRENCH
"
HEX BOLT 3⁄8"-16 X 11⁄4
"
84 P1023SL084 EXTENSION WING
85 PW02
86 PSB14
FLAT WASHER 3⁄8
"
218 P1023SL218 ELECTRICITY LABEL
219 P1023SL219 READ MANUAL LABEL
220 P1023SL220 ALLEN WRENCH 3MM
221 P1023SL221 ALLEN WRENCH 4MM
300 P1023SL300 BLADE GUARD ASSEMBLY
301 P1023SL301 USE GUARD LABEL
CAP SCREW 3⁄8"-16 X 1"
87 P1023SL087 MAGNETIC SWITCH
87A PS31
87B PN07
PHLPHD SCRW 10-24 X 13⁄4
HEX NUT 10-24
"
87C P1023SL087C MOTOR CORD
87D P1023SL087D POWER CORD
87E P1023SL087E LOCKING CABLE TIES
87G P1023SL087G GROMMET
400 P1023400
401 P1023401A
402 P1023402
403 P1023403
404 P1023404A
405 P1023405
406 P1023406
407 P1023407
408 P1023408
409 P1023409
410 P1023410
411 P1023411
412 P1023412
COMPLETE MITER GAUGE
KNOB
FLAT WASHER 1⁄4
"
MITER GAUGE BODY
MITER BAR
SPECIAL WASHER
FLAT HD SCREW
HEX NUT
SETSCREW
SETSCREW
STOP
87H P1023SL087H WIRE CONNECTORS
88 P1023SL088 SWITCH PLATE
88A P1023SL088A FLT HD SCREW 5⁄16"-18 X 1"
88B PW07
88C PN02
89 PK02M
FLAT WASHER 5⁄16"
HEX NUT 5⁄16"-18
KEY 5 X 5 40MM
90A P1023SL090A WARNING ID LABEL
91 P1023SL091 DUST HOSE ADAPTER
92 PW07
LOCK WASHER 5⁄16"
POINTER
SCALE
94 P1023SL094 DUST DEFLECTOR
413 P1023SL413 SETSCREW 10-24 X 5⁄8
414 P1023SL414 ROLL PIN 1.5 X 13
415 P1023SL415 MITER HINGE PIN
"
95 P1023SL095 SPECIALSCRW 5⁄16"-18 X 11⁄4
"
95A PSS08
95B PN02
SETSCREW 5⁄16"-18 X 1⁄2
HEX NUT 5⁄16"-18
"
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-43-
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1.
2.
Low voltage.
Open circuit in motor or loose con- 2.
nections.
1. Check power line for proper voltage.
Motor will not start.
Inspect all lead connections on motor for loose or open con-
nections.
1.
2.
Short circuit in line cord or plug.
Short circuit in motor or loose con- 2.
nections.
1.
Inspect cord or plug for damaged insulation and shorted wires.
Inspect all connections on motor for loose or shorted terminals
or worn insulation.
Motor will not start; fuses or
circuit breakers blow.
3.
Incorrect fuses or circuit breakers in 3.
power line.
Install correct fuses or circuit breakers.
1.
2.
Motor overloaded.
Air circulation through the motor 2.
restricted.
1.
Reduce load on motor.
Clean out motor to provide normal air circulation.
Motor overheats.
1.
Short circuit in motor or loose con- 1.
nections.
Inspect connections on motor for loose or shorted terminals or
worn insulation.
Correct the low voltage conditions.
Install correct fuses or circuit breakers.
Motor stalls (resulting in
blown fuses or tripped cir-
cuit).
2.
3.
Low voltage.
2
Incorrect fuses or circuit breakers in 3.
power line.
4.
1.
2.
1.
Motor overloaded.
4.
Reduce load on motor.
Applying too much pressure to work- 1.
piece.
Belts loose.
Feed workpiece slower.
Machine slows when oper-
ating.
2.
Tighten belts.
Loud, repetitious noise com-
ing from machine.
Pulley setscrews or keys are missing 1.
or loose.
Inspect keys and setscrews. Replace or tighten if necessary.
2.
3.
Motor fan is hitting the cover.
V-belts are defective
2.
3.
Tighten fan or shim cover.
Replace V-belts. See Maintenance.
Blade is not square w/miter
slot or fence is not square to
blade.
1.
2.
3.
Blade is warped.
Table top is not parallel to blade.
Fence is not parallel to blade.
1.
2.
3.
Replace blade.
Make table parallel to blade. See Adjustments.
Make fence parallel to blade. See Adjustments.
Fence hits table top when
sliding on to the table.
1.
2.
Front rail is bolted too low on table. 1.
Rear rail is bolted too low on the 2.
table.
Raise front rail.
Raise rear rail.
Blade does not reach 90°.
Blade hits insert at 45°.
1.
2.
90° stop bolt is out of adjustment.
Pointer bracket is hitting before the 2.
blade reaches 90°.
1.
Adjust 90° stop bolt. See Adjustments.
File down the right side of the pointer bracket until the blade
can reach 90°.
1.
2.
3.
Hole in insert is inadequate.
Table out of alignment.
Blade position is incorrect.
1.
2.
3.
File or mill the hole in the insert.
Align table. See Adjustments.
Adjust blade position. See Adjustments.
Blade won’t go beneath
table surface.
Table top too low.
Raise table top w/washers.
1.
2.
3.
Hand wheel key is inserted too far.
Bullets are wedged.
Roll pin or setscrew in worm gear is 3.
contacting geared trunnion.
1.
2.
Remove hand wheel and adjust key.
Remove hand wheel and adjust bullets.
Inspect roll pins and setscrews in the worm gear. Tighten if
necessary.
Hand wheels won’t turn.
Disconnect power to the
machine when perform-
ing any maintenance or
repairs. Failure to do this
may result in serious
personal injury.
-44-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
-45-
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, spe-
cial, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the car-
ton. We will not accept any item back without this number. Proof of purchase must accompany the mer-
chandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
-46-
G1023SL/G1023SLX Left-Tilting 10'' Table Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name ____________________________________________________________________________________
Street ____________________________________________________________________________________
City ______________________________________________________________State________Zip_________
Phone Number_______________________E-Mail_______________________FAX________________________
MODEL #_____________________Serial # __________________________ Order #______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of
course, all information is strictly confidential.
1.
How did you learn about us?
9.
How many of your woodworking machines are Grizzly? _____________
Which benchtop tools do you own? Check all that apply.
___Advertisement
___Catalog
___Friend
___Card Deck
___World Wide Web
10.
___Other__________________________________________________
Which of the following magazines do you subscribe to.
___1" x 42" Belt Sander
___5" - 8" Drill Press
___8" Table Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Mini Jointer
___6" - 8" Grinder
___Mini Lathe
___10" - 12" Thickness Planer
___Scroll Saw
___Spindle/Belt Sander
2.
___American Woodworker
___Cabinetmaker
___Practical Homeowner
___Shop Notes
___Family Handyman
___Fine Homebuilding
___Fine Woodworking
___Home Handyman
___Journal of Light Construction
___Old House Journal
___Popular Mechanics
___Popular Science
___Today’s Homeowner
___WOOD
___Wooden Boat
___Woodshop News
___Woodsmith
___Woodwork
___Woodworker
___Woodworker’s Journal
___Workbench
___Other__________________________________________________
How many of the machines checked above are Grizzly? ____________
11.
12.
Which portable/hand held power tools do you own? Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
___Popular Woodworking
___Other__________________________________________________
Which of the following woodworking/remodeling shows do you watch?
3.
___Miter Saw
___Backyard America
___Home Time
___The American Woodworker
___The New Yankee Workshop
___This Old House
___Woodwright’s Shop
___Other__________________________________________________
What machines/supplies would you like Grizzly Industrial to carry?
13.
___Other__________________________________________________
What is your annual household income?
__________________________________________________________
__________________________________________________________
What new accessories would you like Grizzly Industrial to carry?
__________________________________________________________
__________________________________________________________
What other companies do you purchase your tools and supplies from?
__________________________________________________________
__________________________________________________________
Do you think your purchase represents good value?
4.
5.
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
14.
15.
What is your age group?
___20-29
___30-39
___40-49
___50-59
___60-69
___70 +
6.
7.
8.
How long have you been a woodworker?
16.
17.
18.
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
___Yes
Would you recommend Grizzly Industrial to a friend?
___Yes ___No
___No
How would you rank your woodworking skills?
___Simple
___Intermediate
___Advanced
___Master Craftsman
Would you allow us to use your name as a reference for Grizzly customers
in your area? Note: We never use names more than three times.
What stationary woodworking tools do you own? Check all that apply.
___Yes
___No
___Air Compressor
___Band Saw
___Drill Press
___Drum Sander
___Dust Collector
___Horizontal Boring Machine
___Jointer
___Panel Saw
___Planer
19.
Comments:_________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
___Power Feeder
___Radial Arm Saw
___Shaper
___Spindle Sander
___Table Saw
___Lathe
___Mortiser
___Vacuum Veneer Press
___Wide Belt Sander
___Other__________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
|