MODEL H8189/H8190
GASOLINE PRESSURE WASHER
OWNER'S MANUAL
H8190
H8189
COPYRIGHT © AUGUST, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#LO9705 PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
INTRODUCTION............................................................................................................................... 2
Foreword .................................................................................................................................... 2
Contact Info................................................................................................................................ 2
General Identification ................................................................................................................. 5
SECTION 1: SAFETY....................................................................................................................... 6
Safety Instructions for Machinery............................................................................................... 6
Additional Safety Instructions for Pressure Washers................................................................. 8
SECTION 3: SETUP......................................................................................................................... 9
Unpacking .................................................................................................................................. 9
Inventory..................................................................................................................................... 9
Assembly.................................................................................................................................. 10
SECTION 4: OPERATIONS ........................................................................................................... 11
Connections and Controls........................................................................................................ 11
Break-In.................................................................................................................................... 12
Adjusting Pressure................................................................................................................... 12
Changing Nozzles.................................................................................................................... 12
Applying Chemicals.................................................................................................................. 13
Standing Water Source............................................................................................................ 14
Spray Gun Lock ....................................................................................................................... 15
Starting..................................................................................................................................... 15
Shutdown Procedure................................................................................................................ 16
SECTION 4: ACCESSORIES......................................................................................................... 17
SECTION 6: MAINTENANCE ........................................................................................................ 18
Schedule .................................................................................................................................. 18
General Maintenance............................................................................................................... 19
Engine Oil Change................................................................................................................... 19
Pump Oil Change..................................................................................................................... 20
Air Filter Service....................................................................................................................... 21
Spark Plug Adjustment and Replacement ............................................................................... 21
Troubleshooting........................................................................................................................ 22
H8189 Pump Parts Breakdown................................................................................................ 23
H8190 Pump Parts Breakdown................................................................................................ 25
H8189 Engine Parts Breakdown.............................................................................................. 27
H8190 Engine Parts Breakdown.............................................................................................. 29
H8189 Frame and Accessories Parts Breakdown ................................................................... 31
H8190 Frame and Accessories Parts Breakdown ................................................................... 33
H8189-90 Machine Labels Breakdown.................................................................................... 35
WARRANTY AND RETURNS........................................................................................................ 38
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Contact Info
Foreword
If you have any comments regarding this manual,
please write to us at the address below:
We are proud to offer the Model H8189 6.5HP
2500 PSI Pressure Washer and the Model H8190
13 HP 3600 PSI Pressure Waasher. This machine
is part of a growing Grizzly family of fine power
tools. When used according to the guidelines
set forth in this manual, you can expect years
of trouble-free, enjoyable operation and proof of
Grizzly’s commitment to customer satisfaction.
Grizzly Industrial, Inc.
Technical Documentation Manager
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
Email: [email protected]
We stand behind our machines. If you have any
service questions or parts requests, please call or
write us at the location listed below.
The specifications, drawings, and photographs
illustrated in this manual represent the Model
H8189 and H8190 when the manual was prepared.
However, owing to Grizzly’s policy of continuous
improvement, changes may be made at any time
with no obligation on the part of Grizzly.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
For your convenience, we always keep current
Grizzly manuals available on our website at www.
grizzly.com. Any updates to your machine will
be reflected in these manuals as soon as they
are complete. Visit our site often to check for the
latest updates to this manual!
-2-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
�������������
�����
������������������������������������������������������������������������������������������
�����������
�������������������������������
�������������������
���������������������������������������������������������������������������������������������������������������������������������������������������������� ������������������
�������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
������
������������������������������������������������������������������������������������������������������������������������������������������������������������������������
��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� �����
���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
�������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������������������������������������������������������������������� ����������������
��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
�������������������������������������������������������������������������������������������������������������������������������������������������������������������� ������
��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
�����
���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
�������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
�����������������������������������������������������������������������������������������������������������������������������������������������������������������������������
���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
�������������������������������������������������������������������������������������������������������������������������������������������������������������������� ������
�������������
����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� �����
���������
����������������������������������
�����������������������������������������������������������������������������������������
��������������������������������������
��������������������������������
-3-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
�������������
�����
������������������������������������������������������������������������������������������
�����������
���������������������������������������
�������������������
������������������������������������������������������������������������������������������������������������������������������������������������������� ���������������������
������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
������
������������������������������������������������������������������������������������������������������������������������������������������������������������������������
��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� �����
���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
�������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������������������������������������������������������������������� ����������������
��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
�������������������������������������������������������������������������������������������������������������������������������������������������������������������� ������
������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
�����
����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
�������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
�����������������������������������������������������������������������������������������������������������������������������������������������������������������������������
���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
�������������������������������������������������������������������������������������������������������������������������������������������������������������������� ������
�������������
����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� �����
���������
����������������������������������
�����������������������������������������������������������������������������������������
��������������������������������������
��������������������������������
-4-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
General Identification
B
C
A
D
E
F
G
H
Figure 1. General component identification
E. High Pressure Hose
A. Engine
B. Handle
C. Nozzles
D. Spray Gun
F. Pump
G. Frame and Wheels
H. Spray Gun Wand
-5-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
�����������������
��������������������������������������
������������������������������������
��������������������������������������������������������������������������������������������������
��������������������������������������������������������������������������������������������
��������������������������������������������������������������������������������������������
��������������������������������������������������������������������������������������������
��������������������
�������������������������������������������������������������������
���������������������������������������
�������������������������������������������������������������������
����������������������������������������
�������������������������������������������������������������������
���������������������������������������������������������������������
�������������������������
������������������������������������������������������������������
��������������������������������
������
Safety Instructions for Machinery
���������������������������������
���� �������������������������������
�����������������������������������
����� �������� ������� �������� ��� ����������
�������
��� ������� ���� �������� �����������
����� ���������� �����������
���������� ������ ���� ������ ����������
��������������
��� ����� ������� ��������� ��� ����
����������������������������������������������
�������������������������������������������
����� ����������� ����� ��������� ��� ��������
�������������������������������������
��� ������� ���� ����� ���������
�������������������������������
����������� ��������� ����������� �����
����� ������� ���������� ������������ ����
�������������������
��� ������ �������� ���������� �����
��������������������������������
������������������������������������
������������������������������������
��� ������� ����� �� ������ ���������
����������� ����� ����������
���������� ����� ��������� ������
����� ����� ���� ������ ������� ������������
����������
-6-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
���������������������������������
��� ����� ������ �������� ���� �����
������������ ���������� ����� ����
����� ����������� ���������� ���
�������� ����������� ����� �����
��������������������������������������������
�����������
���������������������������������������
����������������������������������������
�����������������
���� ������ ���� �������� ������
����������������������������������
�������������������������������������������
�������������������������������������������
����������������������������������������
���������������������������������������
��� ���������������������������������
����� ���� ��������� ���� ��������� �� ����� ����
�������������������������
���� ������������������������������
���������� ������� ���������� ���� �������
������������������
���� ���� ������������ �������������
������������������������������������������
������� ������������� ��������� ��������
�����������������������������
���� ������ ������ ����� �������� ���
��������������������������������������
����������������������������������������
����������������������������������
�������� ���� ������ ����������� ����� ���
�����������������������������������������
������������������
�������� ���� ���� ��� ����������
�������������� ��� ���� ���� �������
�����������������������������������������
��������������������������������������
���� ������� ����������� ���� ������� ���
�����������������������������������������
����� �� �������� ���������� ��������� �����
������������������������������������������
��������
�����������������������������������
��������������������������������������
����������������
���� �������������������������������������
�������������������������
���� ������������������������������
��������������������������������
��������������������������������������
����������� ������ ������� ���������� ������
���������������������������������������
���� ����� ��������� ���� �������
����������� ������� ����������
�����������������������������������������
������������������������
���� ������� ����������� ����� ������
���� ������� ����� ������� ������
���� ������ ������� ����������
����������
�������
�������������������������������������
�������
����������
�
�����������������������������
�����������������������������������
��� ���� ������������ �������� ��� ������� ����
�������������������������������������������
���� ����� ��� ����� ���� ���� �������� ��� ����
��������������������������������������������
������������������
���� ��������� ���������� ����� ������
�����������������������������������������
��������������������������������������������
�������������������������������������
���������� ����� ������� ���� ��� ������
���� ����� ���������� �������
����������������
-7-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions for Pressure
Washers
1. FLUID INJECTION. This machine operates
at fluid pressures and velocities high
enough to penetrate human and animal
flesh. Should such an injury occur, it may
be a surgical emergency. DO NOT treat
fluid injection as a normal cut, instead, see
a physician immediately.
6. CHANGING NOZZLES. Be sure to release
water pressure before changing nozzles, or
performing any service or maintenance, to
reduce the risk of fluid injection injury.
7. APPROVED FLUIDS. Some cleaning
fluids could cause injury to skin, eyes, or
lungs. Use only cleaning fluids approved
for high pressure washers and follow the
manufacturer's recommendations. Never
spray any corrosive chemicals, poisons,
insecticides, or flammable solvents with
this machine.
2. ADEQUATE VENTILATION. During
operation this machine produces carbon
monoxide, which is a poisonous gas. Make
sure the work area is adequately ventilated.
Never operate this machine indoors.
3. COOLING ENGINE. Motor parts get hot
during operation. Allow to cool before
placing hands near motor, adding fuel, or
performing any service or maintenance.
8. HOLDING SPRAY GUN. The reactive
force of the spray will cause the gun to
move, and could cause the operator to
fall or misdirect the spray. Always stand in
a stable position, grip the gun firmly with
both hands, and do not overreach. Use
extreme caution on roofs and ladders and
always wear appropriate harnesses and
safety equipment.
4. FUEL SPILLS. Fuel exposed to hot engine
components may ignite. Thoroughly clean
all fuel spills before starting.
5. ELECTRICAL OVERSPRAY HAZARD.
Spraying water near electrical outlets,
switches, or objects connected to an
electrical circuit, could result in a fatal
electric shock.
9. SLIPPING HAZARDS. The use of pressure
washers can create puddles and other
slippery surfaces. Use extreme caution on
these surfaces to reduce the risk of a fall.
Like all machinery there is potential danger
when operating this machine. Accidents are
frequently caused by lack of familiarity or
failure to pay attention. Use this machine
with respect and caution to lessen the
possibility of operator injury. If normal safety
precautions are overlooked or ignored,
serious personal injury may occur.
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
Failure to do so could result in serious
personal injury, damage to equipment, or
poor work results.
-8-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: SETUP
Inventory
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu-
al to become familiar with
the controls and opera-
tions before starting the
machine!
The following is a description of the main
components shipped with your machine. Lay the
components out to inventory them.
Note: If you can't find an item on this list, check
the mounting location on the machine or examine
the packaging materials carefully. Occasionally
we pre-install certain components for shipping
purposes.
Unpacking
Your machine was carefully packaged for safe
transportation. Remove the packaging materials
from around your machine and inspect it. If you
discover the machine is damaged, please imme-
diately call Customer Service at (570) 546-9663
for advice.
A
E
B
D
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
C
When you are completely satisfied with the condi-
tion of your shipment, inventory the contents.
Figure 2. Model H8189/H8190 inventory
H8189/H8190 Inventory (Figure 2)
Qty
A. Handle........................................................ 1
B. Spray Gun .................................................. 1
C. Spray Gun Wand........................................ 1
D. Pressure Washer........................................ 1
E. High Pressure Hose ................................... 1
F. Input Hose (Not Shown)............................. 1
-9-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
B
C
Refer to Figure 1 on Page 4 for identification of
components in the following steps.
A
To assemble the H8189/H8190:
1. Insert the handle into the frame posts and
push down until the securing pins latch in the
securing pin holes.
F
E
D
Note: You may need to push the securing
pins in to allow the handle to slide into the
frame posts.
Figure 3. Model H8189/H8190 accessory
inventory.
2. Thread the spray gun wand into the spray
H8189/H8190 Accessory Inventory (Figure 3)
Qty
gun and tighten securely.
A. Chemical Hose........................................... 1
B. Chemical Filter ........................................... 1
C. O-Ring Seal Kit .......................................... 1
D. Spark Plug Wrench .................................... 1
E. Spark Plug Wrench Handle........................ 1
F. Input Source Filter..................................... 1
G. Hose Adapter Male to Male (not shown)... 1
3. Connect the male end of the high pressure
hose to the pump output quick coupler.
4. Connect the high pressure hose quick coupler
to the spray gun.
5. Thread the female end of the input hose onto
the pump input port.
6. Connect the other end of the input hose to a
spigot providing at least 5 GPM, or to the in-
feed source filter, if drawing from a standing
water source.
Note: Depending on the spigot fitting type,
you may need to use the provided male-to-
male hose adapter to connect the pressure
washer to this type of water source.
-10-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: OPERATIONS
Connections and Controls
H8189/H8190 Engine Controls (Figure 5)
E. Choke
F. Fuel Valve
H8189/H8190 Pump Controls (Figure 4)
A. Pump Out-Feed
B. Pressure Adjustment Knob
C. Chemical Injection Inlet
G. Throttle
H. Pull-Start Rope
I. Motor Switch
D. Pump In-Feed...............................................
B
G
H
C
E
F
I
A
D
Figure 4. Pump Controls.
Figure 5. Engine controls.
-11-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
Break-In
The first 20 hours of operation is condistered the
break-in period. Be sure to follow the maintainence
schedule on Page 16 avter 20 hours of use.
NOTICE
Failure to follow the break-in maintenance
schedule can reduce the lifespan of
the machine and negatively impact
performance.
Water Pressure
Adjustment Knob
Figure 6. Reducing the pump pressure.
•
REDUCE ENGINE SPEED. Slowing the
engine will reduce the pressure created by
the pump.
Adjusting Pressure
NOTICE
Engine speed should always be set high
enough to handle the load of the pump. If
the engine speed is too low, the motor may
bog or stop when the spray gun trigger is
pulled and the pump is activated. Operating
the engine speed at such a setting can
cause excessive engine wear and premature
engine failure.
DO NOT attempt to increase the pump
pressure by tampering with controls or
otherwise altering the machine. A higher
pressure setting than the factory set pressure
may damage the pump or cause components
to fail resulting in serious personal injury.
The pressure setting on the model H8189/H8190
was preset at the factory to achieve optimum
pressure for general purpose cleaning. If you need
to lower the pressure, it can be accomplished by
these methods:
Changing Nozzles
The model H8189/H8190 pressure washer is
equipped with five spray nozzles located in
receptacles on the front panel. Each nozzle is
color coded and delivers a specific spray pattern
for a particular cleaning purpose. The size of the
nozzle determines the shape and pressure of the
spray. The 0°, 15°, 25°, and 40° nozzles are high
pressure nozzles; the chemical nozzle is a low
pressure nozzle.
•
•
•
BACK AWAY FROM THE SURFACE TO BE
CLEANED. Moving further away reduces the
pressure on the workpiece.
SELECT A DIFFERENT NOZZLE. Nozzles
with a wider angled spray deliver a less
powerful stream.
ADJUST THE PRESSURE REGULATOR
ON THE PUMP. Turn the pressure regulator
knob counter-clockwise to lower the pressure
(Figure 6). Once you have finished using
your pressure washer, return the regulator to
its original position by turning it clockwise.
To change nozzles on the H8189/H8190:
1. FOLLOW THE SHUTDOWN PROCEDURE
ON PAGE 14!
-12-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Pull the trigger on the spray gun to release
water pressure. Be sure that all pressurized
water has been released before removing a
nozzle.
Nozzles:
0° Red Nozzle
This nozzle delivers an extremely powerful pinpoint
stream that covers a very small cleaning area.
3. Pull back the quick connect coupler on the
end of the spray gun wand and remove the
current nozzle.
15° Yellow Nozzle
This nozzle delivers a powerful 15° spray pattern
for intense cleaning of small areas.
4. Select a nozzle and with the quick connect
coupler on the spray gun wand pulled back,
insert the nozzle (Figure 7).
25° Green Nozzle
This nozzle delivers a 25° spray pattern for intense
cleaning of larger areas.
40° White Nozzle
This nozzle delivers a 40° spray pattern and a
less powerful stream of water. It covers a wide
area of cleaning.
Chemical Black Nozzle
This nozzle is used to apply chemicals or cleaning
solutions. It has the least powerful stream.
Applying Chemicals
Figure 7. Inserting a nozzle.
5. Release quick connect coupler and twist
nozzle to make sure it is secure in the
coupler.
Use only household detergents, cleaners, and
degreasers recommended for use in pressure
washers. NEVER use toxic or corrosive
chemicals, acids, poisons, insecticides, or
flammable solvents such as gasoline or
kerosene with your pressure washer. Failure
to follow this warning could result in machine
failure, significant property damage, severe
personal injury, or death.
Always double-check coupler connections on
all fittings. Improperly connected fittings can
blow apart under pressure causing severe
personal injury and/or equipment damage.
NOTICE
Always try a nozzle on a small test area or
piece of test material to determine if it is the
correct nozzle for the task. Some nozzles
provide so much pressure they can destroy
even sturdy materials.
Applying chemicals or cleaning solvents
is a low pressure operation. Use only the
chemical nozzle to apply chemicals or
solvents.
-13-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Connect the low pressure chemical nozzle to
the spray gun as described on Page 13.
NOTICE
Chemicals left in the pressure washer can
damage the pump and void the warranty.
Always rinse the unit thoroughly by running
clean water through the chemical hose after
using chemicals or cleaning solvents.
4. After use of chemicals or cleaning solutions,
draw clean water through the chemical hose
and pressure washer to rinse the internal
components.
To apply chemicals:
Standing Water
Source
1. Push the chemical hose onto the barbed
fitting located near the pump water outlet as
shown in Figure 8.
To draw water from a standing source:
1. Attach the supplied input hose filter to the
input hose and place the input hose filter in
the standing water source.
Note: Be sure the water source is free from
debris which could clog the filter and cause
a loss of water flow.
2. Prime the pump by pouring water into the
other end of the input hose (the end without
the filter) while the filter end is submerged in
the water source. Without spilling water out of
the hose, connect the input hose to the input
port on the pump.
Figure 8. The attached chemical hose.
Note: Be sure the water source is large
enough to provide 5 GPM of flow for the
duration of the pressure washer operation.
2. Push the other end of the chemical hose onto
the chemical hose filter (Figure 9) and fully
submerge in a container holding the chemical
or cleaning solution.
NOTICE
If the pump is not able to provide pressurized
water when drawing from a standing water
source, shutdown the pressure washer
immediately and re-attempt to prime the
pump. Failure to follow this instruction can
damage the pump and void the warranty.
Figure 9. The attached chemical hose filter.
-14-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
Spray Gun Lock
Starting
The spray gun has a lockout lever that can be
engaged to prevent accidental discharge. This
feature is especially useful when climbing up a
ladder or doing any work that might accidentally
discharge the spray gun. To engage the lockout
lever, simply flip it away from the trigger and clip it
into the lockout lever groove in the handle (Figure
10). To release the lever, reverse this procedure
(Figure 11).
Operation of this equipment has the potential
to propel debris into the air which can cause
eye injury. Always wear safety glasses or
goggleswhenoperatingequipment. Everyday
glasses or reading glasses only have impact
resistant lenses, they are not safety glasses.
Be certain the safety glasses you wear meet
the appropriate standards of the American
National Standards Institute (ANSI).
To start the H8189/H8190 pressure washer:
1. Check the engine and pump oil level and fuel
level (refer to the MAINTENANCE section
beginning on Page 16 for locations). Add
engine oil (SAE 30) and/or fuel (unleaded
gasoline) if necessary.
2. Securely fasten one end of the provided input
hose to a threaded hose spigot. Securely
fasten the other end of the input hose to the
pump input port.
Figure 10. The spray gun in the locked position.
Note: When drawing water from a standing
source, follow the standing source instructions
on Page 15. When drawing water from a
spigot, you may need to use the provided
male-to-male hose adapter.
3. Makesurethespraygunissecurelyconnected
to the high pressure hose, and that the high
pressure hose is securely connected to the
pump output port.
4. Attach the appropriate nozzle to the quick
coupler at the end of the spray gun wand,
and turn on the water supply at the spigot.
Figure 11. The spray gun in the unlocked
position.
NOTICE
Never allow the motor to run without a water
source connected to the pump. Failure
to follow this instruction will damage the
pump and void the warranty.
-15-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Turn the motor switch to the ON position
6. Set the fuel valve to the OPEN position.
Shutdown Procedure
To shut down the pressure washer:
7. Engage the choke (if cold starting) and set
the throttle to 3⁄4 open.
1. Release the trigger on the spray gun and
return the spray gun to the bracket on the
washer handle.
8. Squeeze the spray gun trigger until a steady
stream of water comes out, then release.
2. Turn the pressure adjustment knob
counterclockwise until there is no more
pressure.
10. Pull the start rope to start the motor.
Note: For best pull-starting results, pull the
start rope with forceful, but even pressure to
spin the motor.
3. Close the fuel valve.
4. Switch the motor to the OFF position.
5. Shut off the water at the spigot, or remove
the input hose from the water if drawing from
a standing source. Purge the pressure from
the system by pulling the spray gun trigger.
When pull-starting, pull the start rope slowly
until resistance is felt, then pull with forceful,
even pressure. Rapidly jerking the start rope
can cause it to forcefully recoil, potentially
causing hand and/or arm injury.
NOTICE
11. Allow the motor to run long enough to achieve
normal operating temperature (at least two
minutes), then set the throttle to the desired
speed.
To reduce the risk of damaging engine
components, DO NOT stop the engine
abruptly when it is running under load.
12. Pull the trigger on the spray gun to release
pressurized water and begin work.
Note: If the motor does not start after several
pulls of the start rope, or brief turns of the
start switch, repeat the starting instructions
from Step 8. If you are still unable to start the
motor, refer to the troubleshooting guide on
Page 20.
NOTICE
Never allow the motor to run for more than
five minutes without pulling the trigger
on the spray gun to release water. Failure
to follow this instruction can damage the
pump and void the warranty.
-16-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: ACCESSORIES
G9927 and H3143—Wax Buffer
H8118—Spot Sandblaster
Wax the car in a jiffy with this buffer/polisher
system. The pad duplicates hand polishing with
a random orbit rotation. Kit includes a wax
application bonnet and a terrycloth polishing
bonnet. Safe for all types of finishes, gives a
beautiful swirl free result.
This spot sandblaster is the quickest, cleanest
way to remove rust spots, peeling paint, or surface
blemishes without disturbing the surrounding
area. Supplied with 4 nozzles that allow you to
spot blast inside corners, outside corners, edges,
and flat areas for perfect surface prep.
G9927
H3143
Figure 14. Models G9927 and H3143 Wax
Figure 12. Model H8118 Spot Sandblaster.
Buffers.
G7142—Long Rubber Gloves
H3265—24" Blow Gun
Get into hard-to-reach areas with this 24” long
Blow Gun. Includes rubber tip. 1/4” female NPT.
Industrial strength rubber gloves with 11" cuffs
protect from finger tip to elbow. Positive grip on
hands and fingers. Alkali and acid resistant.
H3261—5 pc. Air Blow Kit
This chrome plated, brass body Air Blow Gun
includes five different tips for all normal air
cleaning jobs. 1/4" NPT air inlet.
H3265
Figure 13. Model G7142 Sandblasting Gloves.
H3261
Figure 15. Model H3265 and H3261 air tools.
-17-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: MAINTENANCE
NOTICE
Operating machinery in harsh conditions
may require more frequent maintenance.
The maintenance schedule below is merely
a guideline for general use. If you operate
your machine in extremely hot, cold, or
dusty conditions, change oils and clean or
replace filters with increased frequency.
Always release water pressure and allow
engine to cool before performing any service
or maintenance. Failure to follow this warn-
ing can result in severe burns and/or fluid
injection injuries.
Schedule
For optimum performance from your machine,
follow this maintenance schedule and refer to any
specific instructions given in this section.
Interval
Daily
Every 20
hours or 1
month
Every 100
hours or 3
months
Every 500
hours or 6
months
Every 1000
hours or 12
months
Maintenance
Check and tighten
bolts
X
X
X
X
Check for worn or
damaged wires
Check for oil/fuel
leaks
Check engine oil
Change engine oil
X (First Time-
Break In)
X
X
Check pump oil
Change pump oil
X
X (First Time-
Break In)
Clean outer air filter
Clean filter core
X
X
Replace filter core
Clean fuel tank
X
X
Check Spark Plug Gap
X
Figure 16. Maintenance schedule
-18-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
General Maintenance
Dipstick/Oil Cap
Before each use, perform the following general
maintenance tasks:
1. Check the engine oil and fuel level
2. Check the engine for cracked fuel lines,
loose bolts, and any other excessively worn
or damaged parts. Repair or replace worn or
damaged parts as necessary. Tighten any
loose bolts.
Drain Plug
Figure 17. Motor maintenance points.
3. Check the high pressure hose for leaks.
Replace if necessary.
4. Allow the oil to drain for several minutes until
all the oil has drained from the crankcase.
4. Inspect the spray gun and nozzles for clogged
debris and/or damage. Clean any debris with
a garden hose and replace any damaged
parts.
5. Fasten the drain plug securely.
6. Remove the dipstick/oil cap and fill with SAE
30 motor oil checking the level on the dipstick
frequently until full (Figure 18). Do not over-
fill.
5. Inspect the chemical injection hose and filter
for clogged debris and/or damage. Clean any
debris with a garden hose and replace any
damaged parts.
Engine Oil Change
Replace the engine oil once after 20 hours, and
then regularly every 100 hours or 3 months (more
frequently in harsh conditions).
To change the engine oil:
1. FOLLOW SHUTDOWN PROCEDURE AND
ALLOW ENGINE TO COOL!
Figure 18. Correct engine oil level on the
2. Loosen the dipstick/oil cap.
dipstick.
3. Remove the drain plug on the side of the
engine (Figure 17) and allow oil to drain
through the hole in the frame into a catch
basin.
7. Tighten the dipstick/oil cap.
8. Dispose of the used oil in accordance with
local regulations.
-19-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
Pump Oil Change
Replace the pump oil once after 20 hours, and
then regularly every 100 hours or 3 months.
To change the pump oil:
1. FOLLOW SHUTDOWN PROCEDURE AND
ALLOW ENGINE TO COOL!
2. Loosen the oil cap (Figure 19).
3. Place a container under the oil drain plug
(Figure 19).
Figure 20. The correct pump oil level in the
viewport.
7. Replace the oil cap and tighten securely.
Oil Cap
8. Dispose of the used oil in accordance with
local regulations.
Oil Level Viewport
Drain Plug
Figure 19. The pump oil cap and drain plug.
4. Remove the oil drain plug.
5. After all the oil has drained, replace the oil
drain plug and tighten securely.
6. Remove the oil cap and fill with SAE 30 oil.
Add oil slowly and check the level frequently.
The pump is full when oil is just past the red
dot, covering the lower 2⁄3 of the viewing port
(Figure 20). Do not overfill.
-20-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Filter Service
Spark Plug
Adjustment and
Replacement
Clean the outer air filter element every 20 hours or
1 month (more frequently in harsh conditions).
To clean the outer air filter element:
Check the spark plug gap and adjust it if nec-
essary after every 100 hours of operation or 3
months.
1. FOLLOW SHUTDOWN PROCEDURE AND
ALLOW ENGINE TO COOL!
To adjust the spark plug gap:
2. Remove the air filter cover by first removing
the air filter cover wing nut.
1. Disconnect the plug wire. With the provided
spark plug tool, remove the spark plug.
3. Remove the wing nut and washer holding
the air filter in place and remove the air filter
assembly (Figure 21).
2. Carefully inspect the plug for signs of wear.
If there is pronounced coloration, excessive
corrosion or deposits, or damage to any com-
ponent of the plug, replace it.
3. Using a spark plug gap gauge (available at
most automotive stores), measure the cur-
rent spark plug gap.
Note: The gap is the distance between
the side electrode and the center electrode
(Figure 22).
Center Electrode
Side Electrode
Figure 21. Removing the air filter.
4. Remove the outer foam air filter element.
5. Clean the outer element thoroughly with sol-
vent and allow to dry.
6. Saturate the outer element with fresh motor
oil, then squeeze with a cloth to remove any
excess oil.
Figure 22. The spark plug electrode gap.
7. Replace the outer air filter element, then
replace the air filter assembly, filter wing nut,
filter cover, and filter cover wing nut.
4. Using a flat blade screw driver or similar tool,
bend the side electrode up or down as neces-
sary to achieve the correct spark plug gap of
0.7-0.8mm Take care not to damage the plug
when doing this.
Note: To clean the air filter core, DO NOT
use solvent or any other cleaning solution.
Instead, use a soft brush to remove any par-
ticulate build-up.
5. Reinstall the plug with the provided spark
plug tool and reconnect the spark plug wire.
-21-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Symptom
Possible Cause
Solution
Engine won't start.
1. Fuel tank is empty.
1. Add fuel.
2. Fuel valve is closed.
2. Open fuel valve.
3. Spark plug wire is not attached.
4. Spark plug is fouled.
3. Attach spark plug wire.
4. Replace spark plug.
5. Air filter is clogged.
5. Clean air filter.
6. Water pressure has built up in the pump.
6. Release water pressure by squeezing spray gun trig-
ger.
7. Internal engine components have failed.
7. Refer to engine manual and/or see a qualified tech-
nician for repair.
Engine starts, but 1. Engine speed is too slow.
1. Increase throttle setting.
2. Clear the fuel lines.
3. Fully open the fuel valve.
4. Replace with a clean, quality, unleaded gasoline.
5. Clean air filter.
runs poorly.
2. The fuel line is clogged.
3. The fuel valve is partially closed.
4. Low quality or contaminated fuel.
5. Air filter is dirty.
6. Internal engine components are worn or 6. Refer to a qualified technician.
have failed.
No, or low, water 1. Low water supply.
pressure. 2. Low pressure nozzle attached.
1. Water supply must flow at least 5 GPM.
2. Attach a higher pressure nozzle.
3. Tighten or replace fitting as necessary.
4. Remove and clean filter.
3. Leak at high pressure hose fitting.
4. Water filter screen clogged.
5. Engine is not in high throttle position.
6. High pressure hose is too long.
5. Increase engine speed with throttle lever.
6. Use high pressure hose under 100 ft.
7. Engine or pump components are worn or 7. Refer a qualified technician for repair.
have failed.
Will not draw chemi- 1. Spray gun does not have low pressure 1. Attach low pressure nozzle.
cals.
nozzle attached.
2. Chemical filter clogged.
2. Clean filter.
3. Chemical hose and filter not fully sub- 3. Be sure chemical hose and filter stay fully sub-
merged in chemical.
merged in chemical.
4. Chemical is too thick.
4. Dilute chemical. Chemicals should be the consis-
tency of water.
-22-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8189 Pump Parts Breakdown
-23-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8189 Pump Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PH8189001 CRANK CASE COVER BOLT
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
PH8189051 VALVE JACKET INNER GASKET
2
PH8189002 OIL DRAIN PLUG
PH8189052 WATER RETURN VALVE CORE
PH8189053 WATER RETURN VALVE JACKET
PH8189054 VALVE JACKET OUTER GASKET
PH8189055 WATER RETURN VALVE SEAT
PH8189056 VALVE SEAT GASKET
3
PH8189003 OIL DRAIN PLUG WASHER
PH8189004 CRANK CASE COVER
PH8189005 CRANK CASE COVER GASKET
PH8189006 SIGHT GLASS
4
5
6
7
PH8189007 SIGHT GLASS GASKET
PH8189008 SIGHT GLASS CAP
PH8189057 WATER OUTLET T-CONNECTOR
PH8189058 T-CONNECTOR GASKET
PH8189059 OUTLET T-CONNECTOR FIXED BOLT
PH8189060 FIXED BOLT WASHER
8
9
PH8189009 OIL INLET PLUG
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
PH8189010 OIL INLET PLUG GASKET
PH8189011 CRANK CASE
PH8189061 FIX BOLT GASKET
PH8189012 CRANK SHAFT COVER BOLT
PH8189013 CRANK SHAFT COVER
PH8189014 BEARING COVER GASKET
PH8189015 BEARING CLIP
PH8189062 OUTLET T-CONNECTOR GASKET
PH8189063 CYLINDER
PH8189064 SCREW GASKET
PH8189065 SCREW CAP
PH8189016 BALL BEARING
PH8189066 INLET T-CONNECTOR GASKET
PH8189067 BOLT WASHER
PH8189017 CRANKSHAFT
PH8189018 NEEDLE ROLLER BEARING
PH8189019 FLANGE RING
PH8189068 INLET T-CONNECTOR GASKET
PH8189069 WATER INLET T-CONNECTOR
PH8189070 INLET T-CONNECTOR GASKET
PH8189071 INLET SCREW GASKET
PH8189072 INLET SCREW
PH8189020 CRANK SHAFT GASKET
PH8189021 FLANGE
PH8189022 FLANGE BOLT
PH8189023 CONNECTING ROD
PH8189073 WATER INLET CONNECTOR SEAL GASKET
PH8189074 WATER INLET CONNECTOR
PH8189075 QUICK CONNECTOR CAP
PH8189076 BEARING CLIP
PH8189024 CONNECTING ROD PIN
PH8189025 PLUNGER ROD
PH8189026 COPPER WASHER
PH8189027 CERAMIC PLUNGER
PH8189028 PLUNGER CAP SCREW RING
PH8189029 COPPER WASHER
PH8189077 QUICK CONNECTOR GASKET
PH8189078 QUICK CONNECTOR
PH8189079 STEEL BALL
PH8189030 PLUNGER CAP SCREW
PH8189031 LOCATING RING
PH8189080 DETERGENT INJECTOR
PH8189081 INJECTOR SPRING
PH8189032 LOCATING RING WATER SEAL
PH8189033 LOCATING RING GASKET
PH8189034 U-PACKING RING
PH8189082 DETERGENT INJECTOR GASKET
PH8189083 STEEL BALL
PH8189084 INJECTOR NOZZLE
PH8189035 U-PACKING
PH8189085 WATER SHOOTING NOZZLE
PH8189086 WATER OUTLET JOINT
PH8189087 WATER OUTLET JOINT GASKET
PH8189088 WATER OUTLET CONE VALVE SPRING
PH8189089 WATER OUTLET CONE VALVE
PH8189090 WATER OUTLET CONE VALVE GASKET
PH8189091 CHECK VALVE GASKET
PH8189092 CHECK VALVE WASHER
PH8189093 CHECK VALVE FLAKE
PH8189036 U-PACKING SEAT
PH8189037 HANDLE COVER
PH8189038 PRESSURE ADJUSTMENT SCREW
PH8189039 ADJUSTMENT SCREW FIXED NUT
PH8189040 PRESSURE ADJUSTMENT HANDLE
PH8189041 PRESSURE ADJUSTMENT SEAT
PH8189042 PRESSURE ADJUSTMENT FIXED SCREW
PH8189043 PRESSURE ADJUSTMENT VALVE
PH8189044 UPPER SPRING WASHER
PH8189045 PRESSURE ADJUSTMENT SPRING
PH8189046 LOWER SPRING WASHER
PH8189047 ADJUSTMENT VALVE SCREW
PH8189048 WATER RETURN VALVE ROD
PH8189049 VALVE JACKET INNER GASKET
PH8189050 ADJUSTMENT VALVE SEAT
PH8189094 CHECK VALVE SPRING
PH8189095 CHECK VALVE BOX
PH8189096 COMPACTION CAP SEAL GASKET
PH8189097 CHECK VALVE COMPACTION CAP
PH8189098 CYLINDER BOLT WASHER
PH8189099 CYLINDER BOLT
-24-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8189 Engine Parts Breakdown
-25-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8189 Engine Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
PH8189101
PH8189102
PH8189103
PH8189104
PH8189105
PH8189106
PH8189107
PH8189108
PH8189109
PH8189110
PFB01M
RECOIL STARTER ASSEMBLY
ENGINE SWITCH
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
PH8189145
PH8189146
PH8189147
PH8189148
PH8189149
PH8189150
PH8189151
PH8189152
PH8189153
PH8189154
PH8189155
PH8189156
PH8189157
PH8189158
PH8189159
PH8189160
PH8189161
PH8189162
PH8189163
PH8189164
PH8189165
PN01M
VALVE ROTATOR
CONNECTING ROD ASSEMBLY
WRIST PIN CLIP
FAN COVER
SHROUD
WRIST PIN
FLANGE NUT M14-2
STARTER PULLEY
COOLING FAN
PISTON
PISTON RING SET
OIL CAP
FLYWHEEL
FLANGE BOLT M8-1.25 X 32
CRANKCASE COVER ASSEMBLY
DOWEL PIN 8X 14
SIDE PLATE
DIODE
FLANGE BOLT M6-1 X 12
INGNITION COIL ASSEMBLY
FLANGE BOLT M6-1 X 25
DRAIN PLUG
DIPSTICK ASSEMBLY
CRANKCASE GASKET
GOVERNOR ASSEMBLY
GOVERNOR ASSEMBLY SHAFT
RADIAL BALL BEARING 6025
OIL LEVEL SWITCH ASSEMBLY
THROTTLE LEVER ASSEMBLY
GOVERNOR SPRING
GOVERNOR ARM
PH8189112
PH8189113
PH8189114
PH8189115
PH8189116
PH8189117
PH8189118
PH8189119
PH8189120
PH8189121
PH8189122
PH8189123
PH8189124
PH8189125
PH8189126
PH8189127
PH8189128
PH8189129
PH8189130
PH8189131
PH8189132
PH8189133
PH8189134
PH8189135
PH8189136
PH8189137
PH8189138
PH8189139
PH8189140
PH8189141
PH8189142
PH8189143
PH8189144
DRAIN PLUG WASHER
OIL SEAL
CRANK CASE ASSEMBLY
CARBURETOR ASSEMBLY
CARBURETOR PACKING
CARBURETOR INSULATOR
INSULATOR GASKET
CHOKE LEVER
THROTTLE RETUN SPRING
GOVERNOR ROD
HEX NUT M6-1
AIR FILTER GASKET
CYLINDER HEAD STUD
CYLINDER HEAD ASSEMBLY
DOWEL PIN 10 X 16
CYLINDER HEAD GASKET
SPARK PLUG
PH8189167
PH8189168
PH8189169
PH8189170
PH8189171
PH8189172
PH8189173
PH8189174
PH8189175
PH8189176
PH8189177
PH8189178
PH8189179
PS05M
AIR FILTER CASE
AIR FILTER SEPARATOR
AIR FILTER ELEMENT
AIR FILTER COVER
WIND NUT M6-1
HOSE CLAMP
STUD
FUEL LINE
FLANGE BOLT M8-1.25 X 60
VALVE COVER GASKET
VALVE COVER
RUBBER PAD
FLANGE BOLT M6-1 X 25
FUEL TANK PICK-UP TUBE
FUEL TANK
PCV TUBE
ROCKER VALVE ASSEMBLY
PUSH ROD GUIDE PLATE
PUSH ROD
FUEL FILLER CAP
FUEL FILTER
PHLP HD SCR M5-.8 X 8
MUFFLER GUARD
VALVE LIFTER
PH8189181
PH8189182
PH8189183
PN03M
CAMSHAFT ASSEMBLY
EXHAUST VALVE
MUFFLER
SPARK ARRESTER
HEX NUT M8-1.25
INTAKE VALVE
VALVE SPRING SEAT
VALVE SPRING
PH8189185
PH8189186
PH8189187
EXHAUST PIPE GASGET
CRANKSHAFT ASSEMBLY
FLANGE BOLT M6-1 X 8
EXHAUST VALVE SPRING RETAINER
INTAKE VALVE SPRING RETAINER
-26-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8189 Frame and Accessories Parts
Breakdown
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
�����
���
�����
���
���
���
���
���
���
���
���
���
���
-27-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8189 Frame and Accessories Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
201
202
203
204
205
206
207
208
209
210
211
212
213
214
PH8189201
PH8189202
PH8189203
PH8189204
PH8189205
PH8189206
PH8189207
PH8189208
PH8189209
PH8189210
PH8189211
PH8189212
PN03M
O-RING KIT
215
216
217
218
219
220
221
PH8189215
PH8189216
PN09M
SPRAY GUN BRACKET
FRAME ASSEMBLY
HEX NUT M12-1.75
WHEEL ASSEMBLY
AXLE
0 DEGREE NOZZLE
15 DEGREE NOZZLE
25 DEGREE NOZZLE
40 DEGREE NOZZLE
CHEMICAL NOZZLE
CHEMICAL FILTER
CHEMICAL HOSE
PH8189218
PH8189219
PH8189220
PSB74M
RUBBER PAD
CAP SCREW M6-1 X 18
HEX NUT M6-1
221-1 PN01M
HIGH PRESSURE HOSE
INPUT HOSE
222
223
224
225
226
PN02M
HEX NUT M10-1.5
LOCK WASHER 10MM
FLAT WASHER 10MM
RUBBER PAD
PLW06M
PW04M
INPUT HOSE FILTER
SPRAY GUN AND WAND ASSEMBLY
HEX NUT M8-1.25
PH8189225
PH8189226
HEX BOLT M10-1.5 60
PW01M
FLAT WASHER 8MM
-28-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8189 Machine Labels Breakdown
���
���
���
���
���
���
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
301 PH8189301 MACHINE ID LABEL
304 PH8189304 SAFETY GLASSES LABEL
305 PH8189305 CARBON MONOXIDE WARNING LABEL
306 PH8189306 READ MANUAL LABEL
302 PH8189302 HOT SURFACES WARNING LABEL
303 PH8189303 FLAMABLE WARNING LABEL
Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine
MUST maintain the original location and readability of the labels on the machine. If any label is
removed or becomes unreadable, REPLACE that label before using the machine again. Contact
-29-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8190 Pump Parts Breakdown
-30-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8190 Pump Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PH8189001 CRANK CASE COVER BOLT
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
PH8189051 VALVE JACKET INNER GASKET
2
PH8189002 OIL DRAIN PLUG
PH8189052 WATER RETURN VALVE CORE
PH8189053 WATER RETURN VALVE JACKET
PH8189054 VALVE JACKET OUTER GASKET
PH8189055 WATER RETURN VALVE SEAT
PH8189056 VALVE SEAT GASKET
3
PH8189003 OIL DRAIN PLUG WASHER
PH8189004 CRANK CASE COVER
PH8189005 CRANK CASE COVER GASKET
PH8189006 SIGHT GLASS
4
5
6
7
PH8189007 SIGHT GLASS GASKET
PH8189008 SIGHT GLASS CAP
PH8189057 WATER OUTLET T-CONNECTOR
PH8189058 T-CONNECTOR GASKET
PH8189059 OUTLET T-CONNECTOR FIXED BOLT
PH8189060 FIXED BOLT WASHER
8
9
PH8189009 OIL INLET PLUG
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
PH8189010 OIL INLET PLUG GASKET
PH8189011 CRANK CASE
PH8189061 FIX BOLT GASKET
PH8189012 CRANK SHAFT COVER BOLT
PH8189013 CRANK SHAFT COVER
PH8189014 BEARING COVER GASKET
PH8189015 BEARING CLIP
PH8189062 OUTLET T-CONNECTOR GASKET
PH8189063 CYLINDER
PH8189064 SCREW GASKET
PH8189065 SCREW CAP
PH8189016 BALL BEARING
PH8189066 INLET T-CONNECTOR GASKET
PH8189067 BOLT WASHER
PH8189017 CRANKSHAFT
PH8189018 NEEDLE ROLLER BEARING
PH8189019 FLANGE RING
PH8189068 INLET T-CONNECTOR GASKET
PH8189069 WATER INLET T-CONNECTOR
PH8189070 INLET T-CONNECTOR GASKET
PH8189071 INLET SCREW GASKET
PH8189072 INLET SCREW
PH8189020 CRANK SHAFT GASKET
PH8189021 FLANGE
PH8189022 FLANGE BOLT
PH8189023 CONNECTING ROD
PH8189073 WATER INLET CONNECTOR SEAL GASKET
PH8189074 WATER INLET CONNECTOR
PH8189075 QUICK CONNECTOR CAP
PH8189076 BEARING CLIP
PH8189024 CONNECTING ROD PIN
PH8189025 PLUNGER ROD
PH8189026 COPPER WASHER
PH8189027 CERAMIC PLUNGER
PH8189028 PLUNGER CAP SCREW RING
PH8189029 COPPER WASHER
PH8189077 QUICK CONNECTOR GASKET
PH8189078 QUICK CONNECTOR
PH8189079 STEEL BALL
PH8189030 PLUNGER CAP SCREW
PH8189031 LOCATING RING
PH8189080 DETERGENT INJECTOR
PH8189081 INJECTOR SPRING
PH8189032 LOCATING RING WATER SEAL
PH8189033 LOCATING RING GASKET
PH8189034 U-PACKING RING
PH8189082 DETERGENT INJECTOR GASKET
PH8189083 STEEL BALL
PH8189084 INJECTOR NOZZLE
PH8189035 U-PACKING
PH8189085 WATER SHOOTING NOZZLE
PH8189086 WATER OUTLET JOINT
PH8189087 WATER OUTLET JOINT GASKET
PH8189088 WATER OUTLET CONE VALVE SPRING
PH8189089 WATER OUTLET CONE VALVE
PH8189090 WATER OUTLET CONE VALVE GASKET
PH8189091 CHECK VALVE GASKET
PH8189092 CHECK VALVE WASHER
PH8189093 CHECK VALVE FLAKE
PH8189036 U-PACKING SEAT
PH8189037 HANDLE COVER
PH8189038 PRESSURE ADJUSTMENT SCREW
PH8189039 ADJUSTMENT SCREW FIXED NUT
PH8189040 PRESSURE ADJUSTMENT HANDLE
PH8189041 PRESSURE ADJUSTMENT SEAT
PH8189042 PRESSURE ADJUSTMENT FIXED SCREW
PH8189043 PRESSURE ADJUSTMENT VALVE
PH8189044 UPPER SPRING WASHER
PH8189045 PRESSURE ADJUSTMENT SPRING
PH8189046 LOWER SPRING WASHER
PH8189047 ADJUSTMENT VALVE SCREW
PH8189048 WATER RETURN VALVE ROD
PH8189049 VALVE JACKET INNER GASKET
PH8189050 ADJUSTMENT VALVE SEAT
PH8189094 CHECK VALVE SPRING
PH8189095 CHECK VALVE BOX
PH8189096 COMPACTION CAP SEAL GASKET
PH8189097 CHECK VALVE COMPACTION CAP
PH8189098 CYLINDER BOLT WASHER
PH8189099 CYLINDER BOLT
-31-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8190 Engine Parts Breakdown
-32-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8190 Engine Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
PH8190101
PH8190102
PH8190103
PH8190104
PFB01M
RECOIL STARTER ASSEMBLY
FLANGE BOLT M6-1 X 8
ENGINE SWITCH
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
PH8190150
PH8190151
PH8190152
PH8190153
PH8190154
PH8190155
PH8190156
PH8190157
PH8190158
PH8190159
PH8190160
PH8190161
PH8190162
PH8190163
PH8190164
PH8190165
PH8190166
PH8190167
PH8190168
PH8190169
PH8190170
PH8190171
PH8190172
PH8190173
PH8190174
PH8190175
PFN01M
AIR FILTER SEPARATOR
AIR FILTER COVER
VALVE COVER BOLT
VALVE COVER BOLT WASHER
VALVE COVER
FAN COVER
FLANGE BOLT M6-1 X 12
SHROUD
PH8190106
PH8190107
PH8190108
PH8190109
PH8190110
PH8190111
PH8190112
PH8190113
PH8190114
PH8190115
PH8190116
PH8190117
PH8190118
PH8190119
PH8190120
PH8190121
PH8190122
PH8190123
PH8190124
PH8190125
PH8190126
PH8190127
PH8190128
PH8190129
PH8190130
PH8190131
PH8190132
PH8190133
PH8190134
PH8190135
PH8190136
PH8190137
PH8190138
PH8190139
PH8190140
PH8190141
PH8190142
PFN02M
VALVE COVER SEAL
FLANGE BOLT M10-1.5 X 80
PCV TUBE
STARTER PULLY
COOLING FAN
FLANGE NUT M16-1.75
WIRING HARNESS CLIP
FLYWHEEL
CYLINDER HEAD
EXHAUST MANIFOLD STUD
SPARK PLUG
OIL SEAL
CAMSHAFT ASSEMBLY
VALVE LIFTER
CRANK CASE ASSEMBLY
DRAIN PLUG
INTAKE VALVE
AMPLIFIER
EXHAUST VALVE
DRAIN PLUG WASHER
WIRE CLIP
PUSH ROD
VALVE SPRING SEAT
VALVE SPRING
FLANGE BOLT M6-1 X 25
IGNITION COIL ASSEMBLY
WIRE GROMMET
INTAKE VALVE SPRING RETAINER
PUSH ROD GUIDE PLATE
ROKER ARM PIVOT STUD
VALVE ROTATOR
STOP SWITCH CORD
OIL SEAL
RADIAL BALL BEARING 6202
GOVERNOR ARM SHAFT
LOCK PIN 10MM
EXHAUST VAVLE SPRING RETAINER
ROCKER ARM
ROCKER ARM NUT
ROCKER ADJUSTING NUT
FLANGE NUT M8-1.25
EXHAUST PIPE GASKET
EXHAUST PIPE
WASHER
FLANGE NUT M10-1.5
O-RING 14MM
PH8190177
PH8190178
PH8190179
PH8190180
PH8190181
PH8190182
PS05M
OIL LEVEL SWITCH ASSEMBLY
BALANCER
MUFFLER GASKET
SPARK ARRESTOR
MUFFLER
CRANKSHAFT ASSEMBLY
KEY
RADIAL BALL BEARING 6207
CYLINDER HEAD GASKET
DOWEL PIN 12 X 20
CARBURETOR STUD
INSULATOR GASKET
INSULATOR
MUFFLER GUARD
PHLP HD SCR M5-.8 X 8
FLANGE BOLT M8-1.25 X 25
OIL CAP
PH8190184
PH8190185
PH8190186
PH8190187
PH8190188
PH8190189
PH8190190
PH8190191
PH8190192
PH8190193
PH8190194
PH8190195
PH8190196
PH8190197
PH8190198
CRANKCASE COVER
CRANKCASE COVER GASKET
DOWEL PIN 8 X 12
CARBURETOR BASE GASKET
CARBURETOR ASSEMBLY
CHOKE LEVER
DIPSTICK ASSEMBLY
GOVERNOR KIT
AIR FILTER GASKET
FLANGE NUT M6-1
AIR FILTER CASE
FLANGE BOLT M6-1 X 20
AIR FILTER SEAL
WRIST PIT CLIP
WRIST PIN
PH8190144
PFB06M
PISTON RING SET
PISTON
PH8190146
PH8190147
PH8190148
PH8190149
CONNECTING ROD ASSEMBLY
CONTROL ASSEMBLY
GOVERNOR SPRING
THROTTLE RETURN SPRING
WING NUT M6-1
WASHER
AIR FILTER ELEMENT ASSEMBLY
-33-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8190 Engine Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
199
200
201
202
203
204
PH8190199
PH8190200
PH8190201
PH8190202
PH8190203
PH8190204
GOVERNOR ARM BOLT
GOVERNOR ARM
FUEL TANK
205
206
207
208
209
PH8190205
PH8190206
PH8190207
PH8190208
PH8190209
FUEL LINE
FUEL TANK JOINT
FUEL TANK JOINT SEAL
FUEL FILTER
FLANGE BOLT M8-1.25 X 25
RUBBER SUPPORTER
FUEL VALVE
FUEL FILTER CAP
-34-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8190 Frame and Accessories Parts
Breakdown
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
�����
���
�����
���
���
���
���
���
���
���
���
���
���
-35-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8190 Frame and Accessories Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
301
302
303
304
305
306
307
308
309
310
311
312
313
314
PH8189201
PH8189202
PH8189203
PH8189204
PH8189205
PH8189206
PH8189207
PH8189208
PH8189209
PH8189210
PH8189211
PH8189212
PN03M
O-RING KIT
315
316
317
318
319
320
321
PH8190215
PH8190216
PN09M
SPRAY GUN BRACKET
FRAME ASSEMBLY
HEX NUT M12-1.75
WHEEL ASSEMBLY
AXLE
0 DEGREE NOZZLE
15 DEGREE NOZZLE
25 DEGREE NOZZLE
40 DEGREE NOZZLE
CHEMICAL NOZZLE
CHEMICAL FILTER
CHEMICAL HOSE
PH8190218
PH8190219
PH8190220
PSB74M
RUBBER PAD
CAP SCREW M6-1 X 18
HEX NUT M6-1
321-1 PN01M
HIGH PRESSURE HOSE
INPUT HOSE
322
333
344
355
366
PN02M
HEX NUT M10-1.5
LOCK WASHER 10MM
FLAT WASHER 10MM
RUBBER PAD
PLW06M
PW04M
INPUT HOSE FILTER
SPRAY GUN AND WAND ASSEMBLY
HEX NUT M8-1.25
PH8190225
PH8190226
HEX BOLT M10-1.5 60
PW01M
FLAT WASHER 8MM
-36-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
H8189 Machine Labels Breakdown
���
���
���
���
���
���
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
401 PH8189301 MACHINE ID LABEL
404 PH8189304 SAFETY GLASSES LABEL
405 PH8189305 HOT SURFACES WARNING LABEL
406 PH8189306 READ MANUAL LABEL
402 PH8189302 FLAMABLE WARNING LABEL
403 PH8189303 CARBON MONOXIDE WARNING LABEL
Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine
MUST maintain the original location and readability of the labels on the machine. If any label is
removed or becomes unreadable, REPLACE that label before using the machine again. Contact
-37-
H8189/H8190 Gasoline Pressure Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
�������������
���������������������������������������������������������������������������������� �
������������������������������������������������������������������������������������
����� ����������������������� ������������������������������� ���� ���������������������
���������������������������� ������ ������������������������ ���������������������������
���������������������������� ������������������������������� ���������������������������
�������������������������������������������������������������������������������������������������������������������
����������������������������������������������������������������������������������
��� ���������������������������
�
����� ��������������
� ���� �������
� ���� ��������
����� �������
����� ������
�
����� ����������
��� �����������������������������������������������������
���� �������������
���� ���������������
���� �����������
���� �����������������
���� ���������������
���� �������������������
���� �������������������
���� �����������������
���� �����������������
���� ����������
���� �����������������
���� ����
���� �����������
���� �������������
���� ���������
���� �����
���� �������������������
���� ����������������������
���� ����������
���� �������������������
���� ��������
���� ��������
���� ���������������
���� ��������������������
���� ������
���� ����
���� ����������
���� �����������������
���� ������������
��� �������������������������������������
�
����� ����������������
� ���� ����������������
����� ���������������
����� ��������
�
����� ����������������
� ���� ����������������
��� �����������������������
�
����� ������
� ���� ������
� ���� ������
����� �����
����� ���
�
����� ������
��� ������������������������������������������������
����� ���������� ����� ���������� ����� ������������
�
� �������������
��� �����������������������������������������������
����� ���� ����� ����
�
����� ����
� �������
� ������
� ������
��� ���������������������������������������������������
��� ����������������������������������������������������
����������
����������
��� ��������������������������������������������������������������������������������������
�������������������������������������������� ���������� � ������
�
���� �������������������������������������������������������������������������������
� ����������������������������������������������������������������������������������
� ����������������������������������������������������������������������������������
� ����������������������������������������������������������������������������������
Download from Www.Somanuals.com. All Manuals Search And Download.
����������������������
�����
�����
����
������������������������
�������������
��������������������������
����������������������
�����������������������������������
�����������������������������������
�������������������������������������
��������������������������������������
��������������������������������������
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the
carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
Download from Www.Somanuals.com. All Manuals Search And Download.
�����������������������������������������������������������������������
�������������������������������������
������������������������������������
�����������������
��������������������������������
���������������������������������
����
�����������������
����
������������������
Download from Www.Somanuals.com. All Manuals Search And Download.
|