Instructions, Repair and Parts
®
10:1 Dyna-Star
Pump Module
312349G
ENG
Provides lubricant flow and pressure to operate a single line parallel automatic lubrication
system. For automatic lubrication systems only.
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
Single Line Parallel Automatic Lubrication Systems
247444, 247574: Pump Module
243170: Hydraulic Vent Valve Kit
247538: Hydraulic Control Module Kit
Custom Tank Installation Kit: 60#: 247970; 120#: 247456; 400#: 247457
3500 psi (24 MPa, 240 bar) Maximum Lubricant Outlet Pressure
3500 psi (24 MPa, 240 bar) Maximum Hydraulic Fluid Inlet Pressure
350 psi (2.4 MPa, 24.1 bar) Maximum Regulated Hydraulic Fluid Pressure
Single Line Series Progressive Lubrication Systems
247706, 247707: Pump Module
247705: Hydraulic Control Module Kit for Remote Mounting with Standard Refinery Drums
247538: Hydraulic Control Module Kit
4500 psi (31 MPa,310 bar) Maximum Lubricant Outlet Pressure
3500 psi (14 MPa, 24.0 bar) Maximum Hydraulic Fluid Inlet Pressure
450 psi (3.1 MPa, 31.0 bar) Maximum Regulated Hydraulic Fluid Pressure
ti11453
ti11454
ti10643
ti10911
Model 247706
Model 247707
Model 247444
Model 247574
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
WARNING
PRESSURIZED EQUIPMENT HAZARD
Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and
cause serious injury.
•
Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking, or servicing equipment.
•
•
Tighten all fluid connections before operating the equipment.
Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
MOVING PARTS HAZARD
Moving parts can pinch or amputate fingers and other body parts.
•
•
•
Keep clear of moving parts.
Do not operate equipment with protective guards or covers removed.
Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,
follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.
BURN HAZARD
Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe
burns, do not touch hot fluid or equipment. Wait until equipment/fluid has cooled completely.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
•
•
•
Read MSDS’s to know the specific hazards of the fluids you are using.
Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
Always wear impervious gloves when spraying or cleaning equipment.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic
fumes, burns, and hearing loss. This equipment includes but is not limited to:
•
•
•
•
Protective eyewear
Clothing and respirator as recommended by the fluid and solvent manufacturer
Gloves
Hearing protection
312349G
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Pump Module Operation
Unpacking
The Dyna-Star pump module was carefully packaged for
shipment by Graco. When the package arrives, perform
the following procedure to unpack the units:
1. Inspect the shipping box carefully for shipping
damage. Contact the carrier promptly if damage is
discovered.
Cycles for Pump Modules 247444 and 247574 for
injector-based, Automatic Lubrication Systems
1. Upon receiving a signal from a 24-volt Lubrication
Controller (J), the 3-way Solenoid Valve (F) opens,
starting the Pump (D) and closes the Vent Valve (U).
2. Unseal the box and inspect the contents carefully.
There should not be any damaged parts.
2. The pump builds pressure until the pressure switch
in the system sends a signal to the Lubrication
Controller (J), ending the cycle or Pump (D) stalls.
3. Compare the packing slip against all items included
in the box. Any shortages or other inspection
problems should be reported immediately.
3. The Lubrication Controller (J) terminates the 24-volt
signal to the 3-way Solenoid Valve (F).
4. Store the box and packing materials in a safe place
for future use. Graco recommends that all packing
materials be saved in case the unit needs to be
shipped again.
4. The 3-way Solenoid Valve (F) closes, stopping the
Pump (D) and opening the Vent Valve (U) into the
Reservoir (P).
5. The Pressure Reducing Valve (S) and Flow Control
Valve (N) control the pump output pressure and
cycle rate.
Pump Module Overview
Cycles for Pump Modules 247706 and 247707 for
Single Line, Series Progressive-based, Automatic
Lubrication Systems
Pump Module Capabilities
Pump Modules 247444 and 247574 for
Injector-based, Automatic Lubrication Systems:
provide lubricant flow and pressure to operate a single
line parallel automatic lubrication system. The module
requires a hydraulic power supply and a timed signal
from a lubrication controller. Based on these signals, the
pump module provides lubricant flow and pressure to
operate the injectors and vents the injector system to
reset the injectors.
1. Upon receiving a signal from the 24-volt Lubrication
Controller (J), the 3-way Solenoid Valve (F) opens;
starting the Pump (D).
2. The Pump (D) provides lubricant flow and pressure
until the Lubrication Controller (J) terminates the
signal to the 3-way Solenoid Valve; stopping the
Pump.
Pump Modules 247706 and 247707 for Single Line,
Series Progressive-based, Automatic Lubrication
Systems: provide lubricant flow and pressure to
operate a single line, series progressive, automatic
lubrication system. The module requires a hydraulic
power supply and a timed signal from a lubrication
controller.
3. The Pressure Reducing Valve (S) and Flow Control
Valve (N) control the pump output pressure and
cycle rate.
4
312349G
Download from Www.Somanuals.com. All Manuals Search And Download.
Pump Module Assembly
Pump Module Assembly
Models 247706 and 247707 only
For divider valve-based automatic lubrication systems.
1. Install Pump (D) on Reservoir (P).
2. Remove Vent Valve Hydraulic Control (J) fitting and
D
3. Install Hydraulic Control Module on Reservoir (P).
4. Connect Tank Line (G) to Pump (D).
G
H
Pressure Relief
Kit 247902
5. Connect Pump High Pressure Hydraulic Line (H) to
Pump (D).
6. Install Pressure Relief Kit (247902) to Pump Outlet.
P
Hydraulic Control
Module
ti11453
Install
Identification
Label Here
FIG. 1 Model 247706 shown
FIG. 2
312349G
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
CAUTION
Read instruction manual 312350 BEFORE installing this
The hydraulic supply must be 10µ filtered or better and sup-
ply 0.5 - 3.0 gpm (1.9 - 11.4 lpm) at 300 psi - 3500 psi (21
bar - 241 bar (2.1 MPa - 24 MPa).
product.
1. Install Ball Valve (AA) (user provided) in the 3/8-inch
High Pressure Hydraulic Line (X).
•
•
Be sure unit is securely mounted before operation.
Do not lift pressurized equipment.
2. Connect the 3/8-inch High Pressure Hydraulic Line
(X) to the High Pressure Hydraulic Connection
swivel (Y).
Grounding (for non-mobile installation)
3. Connect the 3/4-inch Hydraulic Tank Line (T) to the
Tank Hydraulic Connection swivel (Z).
4. Connect the 24 VDC timer controlled signal to the
3-way Solenoid Valve (F).
5. Connect High Pressure Lubricant Supply Line (G) to
the Lubricant Output Connection (C) for Single Line
Parallel Systems or to Pressure Relief Kit Output
Connection for Single Line, Series
1. Loosen grounding lug locknut (A) and washer (B).
2
2. Insert one end of a 12 gage (1.5 mm ) minimum
ground wire (C) into slot in lug (D). Tighten locknut
securely.
Progressive-based Systems.
6. Ground system (see GROUNDING). Mount
3. Connect other end of wire to true earth ground. To
order a ground wire and clamp, order part number
222011.
Reservoir (P) to grounded chassis member.
Vent Valve Kit for Custom Tank Installation
B
C
A
recommended configuration for mounting the vent
valve. Paint the bracket if desired.
D
ti0720
FIG. 3
2. Connect the Hydraulic Control Line (A) to control
module Vent Valve Hydraulic Control (J).
Pump Module
3. Connect Pump Output Connection line (C) to Pump
outlet.
Mount Reservoir (P) on sturdy, flat surface with 6 (six),
3/8-inch diameter bolts. Note location of Fill Port (K),
Hydraulic Lines (A) and Lubricant Outlet Connection (C)
for easy access once installed.
4. Connect the High Pressure Lubricant Supply Line
Lubricant Output (E).
5. Connect the Vent Line (F) to Custom Tank (user
provided).
•
•
The hydraulic system must be depressurized before con-
necting High Pressure Hydraulic Lines (A).
Be sure Breather (M) is not plugged before filling Reser-
voir (P).
6
312349G
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Hydraulic Control Module for Custom Tank
Hydraulic Control Module 247705
(For Single-line, Progressive, Automatic Lubrication
Installation
Systems with refinery reservoir installation)
1. Mount control module on a flat, sturdy surface per
the recommended configuration (Fig. 2, page 8).
1. Mount control module on a flat, sturdy surface. The
6-foot hydraulic supply and hydraulic tank line must
reach the pump when installed in the refinery
reservoir.
2. Connect Pump Tank Line (G) to pump hydraulic
outlet port.
3. Connect Vent Valve Hydraulic Control (J)
connection to the hydraulic control line (A).
2. Connect Pump Tank Line (G) to pump hydraulic
outlet port.
4. Connect the Pump High Pressure Hydraulic Line
(H) to the pump hydraulic input port.
3. Remove Vent Valve Hydraulic Control (J) and add
plug (R) to vent port.
5. Connect high pressure hydraulic supply to the High
Pressure Hydraulic Connection (L) and the tank
lines to the Hydraulic Tank Connection (K).
4. Connect the Pump High Pressure Hydraulic Line
(H) to the pump hydraulic input port.
6. Connect the 3-way Solenoid Valve (P) to the timer.
5. Connect high pressure hydraulic supply to the High
Pressure Hydraulic Connection (L) and the tank
lines to the Hydraulic Tank Connection (K).
Coil should always be installed with lettering facing
out.
312349G
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Typical Installation
The installation shown in Figures 4, 5, 6 and 7 are only a guide for selecting and installing system components. Con-
tact your Graco distributor for assistance in planning a system to suit your needs.
Controller
Capabilities
J
G
Low Reservoir
Level Switch
(Level Indicator,
optional)
E
Pressure Switch
for System Control
H
Remote Alarm Device
(Light or Horn)
R
(user provided
D
A
B
F
AB
U
N
Y
C
M
Z
S
L
P
AA
W
T
V
Hydraulic
Reservoir
Return
K
From Hydraulic
Power Supply
G
X
Front
Back
ti09649b
FIG. 4
Key:
A
B
C
D
E
F
G
H
J
High pressure hydraulic lines
Hydraulic tank line
Lubricant output connection
Pump
Ignition switch*
3-Way solenoid valve
High-pressure lubricant supply lines*
Injector banks*
Lubrication controller*
Fill port
S
T
Pressure reducing valve (PRV)
Hydraulic tank line*
Vent valve
Vent line
Follower plate (optional)
High pressure hydraulic line*
U
V
W
X
Y
Z
High pressure hydraulic connection (swivel)
Tank hydraulic connection (swivel)
AA Ball valve*
AB Level indicator
K
L
Overflow port
M
N
P
R
Breather
Flow control valve (FCV)
Reservoir
*User provided
Ground wire (for non-mobile installation)*
8
312349G
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Vent Valve Installation Kit
Control Module Installation Kit
G
B
A
H
E
C
D
R
Vent
Port
F
J
Q
*
K
P
M
N
ti11457
L
ti9647a
FIG. 5
Key:
FIG. 6
Key:
A
B
C
D
E
F
Hydraulic control line
Vent valve
Pump output connection line
Pressure relief valve
Lubricant output
Vent line
G
H
J
K
L
M
N
P
Q
R
Pump tank line
Pump high pressure hydraulic line
Vent valve hydraulic control
Hydraulic tank connection
High pressure hydraulic connection
Pressure reducing valve
Flow control valve
3-way solenoid valve
Regulated hydraulic pressure gauge
Plug for systems without vent valves. (Installed in Vent
port instead of J, for models 247706 and 247707 only).
*coil should always be installed with lettering facing out
312349G
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Custom Tank Installation
Vent return port
1/2-inch npt (f)
Pump mounting Ø.343 or 5/16-18 (4x)
Vent valve bracket weld locations
Control module Ø.343 or
5/16-18 (2x)
18.0 Max
5.0
5.0
6.875
3.536
3.536
ti9653a
FIG. 7
10
312349G
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation
Pressure Relief Procedure
Models 247706, 247707
To reduce the risk of serious injury follow this pressure
relief procedure whenever you (are):
1. Disable hydraulic supply to Pump (D) by isolating it
from the high pressure hydraulic supply using Ball
Valve (AA).
•
•
•
Instructed to relieve pressure.
Shut off pump.
Check, clean or service any of the system equip-
ment.
2. Disconnect power from Lubrication Controller (J).
Pressure Relief Kit (247902) to catch fluid when
relieving pressure.
•
Install or clean the dispensing valve.
Models 247444, 247574, 247456, 247457,
247970
(247902).
Start-up
1. Disable hydraulic supply to Pump (D) by isolating it
from the high pressure hydraulic supply using Ball
Valve (AA).
2. Do one of the following:
•
•
Open Pressure Reducing Valve (S) to reduce
trapped hydraulic pressure,
Do not insert finger into the overflow port while filling
a reservoir equipped with a follow plate. Injury or
amputation could result.
or
Cycle the timer to open the 3-way solenoid
valve to reduce trapped hydraulic pressure.
Prime Vent Line Models 247444 & 247574
Gauge on control module should read zero pres-
sure after performing this step.
The first time the reservoir is filled, use the vent valve
outlet. This removes all air from the vent line (V).
3. Disconnect power from Lubrication Controller (J).
1. Connect lubricant supply hose from remote filling
station pump unit to outlet of Vent Valve (U).
2. Remove plug in Fill Port (K) located at bottom of
reservoir.
3. Slowly turn on supply lubricant until lubricant
appears in fill port.
4. Remove lubricant supply hose from vent valve.
312349G
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
5. Set hydraulic pressure to pump at lowest pressure
Fill Reservoir
6. Set hydraulic flow rate to pump at lowest rate
needed to get desired results.
1. Connect lubricant supply hose from remote filling
station pump to Fill Port (K).
7. Read and follow instructions supplied with each
system component.
2. Connect High Pressure Lubricant Supply Line (G) to
Vent Valve (U) outlet.
3. Remove plug from Overflow Port (L).
With a primed pump and sufficient hydraulic supply,
the pump starts when the timer activates the sole-
noid valve. The pump stops when the timer deacti-
vates the solenoid valve.
4. Slowly turn on supply lubricant until level of lubricant
reaches overflow port.
•
For systems with a follow plate, fill until the fol-
low plate reaches the overflow port.
CAUTION
Never allow pump to run dry of the fluid being
pumped. A dry pump will quickly accelerate to a high
speed, possibly damaging the pump. If your pump
accelerates quickly, or is running too fast, stop the
pump immediately and check the fluid supply.
•
Refer to Automatic Lubrication System Design
Guidelines Manual 309015 for instructions on
priming remaining system lubricant lines and
further operating instructions.
Shutdown
COMPONENT RUPTURE HAZARD
The maximum working pressure of each component
in the system may not be the same. To reduce the
risk of overpressurizing any component in the
system, be sure you know the maximum working
pressure of each component. Never exceed the
maximum working pressure of the lowest rated
component in the system. Overpressurizing any
component can result in rupture, fire, explosion,
property damage and serious injury.
1. For normal system shut down, disconnect power to
Lubricator Controller (J) by turning off the ignition
switch.
2. Turn of hydraulic supply by closing the Ball Valve
(AA).
Regulate hydraulic pressure to the pump so that no
fluid line, component or accessory is over
pressurized.
12
312349G
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Service
See separate system component manuals for service
instructions. For pump service see manual 312350. For
vent valve service see manual 309099.
Use only Genuine Graco Repair Parts.
Troubleshooting
Problem
Cause
Pump malfunction.
Solution
System does not build sufficient
pressure.
Refer to manual 312350.
Pump turned off too soon.
Increase timer “pump on” setting.
Increase hydraulic flow rate to pump.
Repair or replace solenoid.
Turn pressure up or supply on.
Replace seal.
Solenoid malfunction.
Too low or no hydraulic supply.
Vent valve seal failure.
Vent valve needle/seat failure.
Reservoir out of grease.
Replace needle and seat.
Fill reservoir.
Broken or leaky supply/branch line.
Tighten connections and/or replace
line(s).
Injector failure.
Repair or replace injector.
Pressure in tank line too high due to Remove tank line restrictions.
restrictions in tank line or plumbing
Use larger plumbing.
too small.
Lubricant dispensed from pressure
relief valve.
System pressure set too high.
Decrease hydraulic pressure to
pump.
Pump runs too fast.
Reservoir out of lubricant.
Pump cavitation.
Fill reservoir.
Install a follower plate.
Repair leak.
Leak in distribution system.
Reservoir overfilled.
No hydraulic supply.
Solenoid malfunction.
Lubricant coming out of breather.
Pump will not start.
Drain lubricant until overflow stops.
Verify/check hydraulic supply.
Replace solenoid.
No electrical supply to lubrication
controller.
Turn on electrical supply.
Lubrication controller malfunction.
Pump malfunction.
Refer to controller manual 308950.
Refer to pump manual 312350.
312349G
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Drawing
Parts Drawing
Vent Valve Kit (2): 237170
Control Module Kit (4): 247538
To pump
lubricant outlet
To pump hydraulic inlet
2h
2n
4m
4p
2g
2b
4q
4u
2f
To pump
hydraulic outlet
2p
4g*
4t
2a
2e
4k
4s*
2j
4c*
2i
2c
2k
2d
4d*
4r
4f*
4e*
4h*
2m
4b
4a*
4j
4n
2q
3b
4a*/4h* Torque 40-43 ft-lbs (54-58 Nm)
4c*/4e* Torque 15-20 ft-lbs (20-27 Nm)
3a
4d*
4f*
Torque 20-25 ft-lbs (27-34 Nm)
Torque 68-75 ft-lbs (92-102 Nm)
Torque 22-24 ft-lbs (30-33 Nm)
ti10304a
4g*
4s*
Allows user to plug vent line for use in systems without a vent valve
* Lubricate o-ring with oil before installation
312349G
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Parts List
Model 247706: Dyna-Star 10:1 Pump Module, 60# for Single Line, Progressive, Automatic Lubrication
Systems (includes items 1a, 3, 4, 5)
Model 247707: Dyna-Star 10:1 Pump Module, 90# for Single Line, Progressive, Automatic Lubrication
Systems (includes items 1b, 3, 4, 5)
Model 247574: Dyna-Star 10:1 Pump Module, 60# for Single Line, Parallel, Automatic Lubrication Systems
(includes items 1a - 4)
Model 247444: Dyna-Star 10:1 Pump Module, 90# for Single Line, Parallel, Automatic Lubrication Systems
(includes items 1b - 4)
*Model 247970: Dyna-Star Pump Module Installation Kit 60# (includes items 1a, 2, 3k, 4)
*Model 247456: Dyna-Star Pump Module Installation Kit 120# (includes items 1b, 2, 3k, 4)
*Model 247457: Dyna-Star Pump Module Installation Kit 400# (includes items 1c, 2, 3k, 4)
Ref.
Ref.
No. Part No. Description
Qty
No. Part No. Description
Qty
3h
3i
3j
3k
3l
4
247448 . COVER, reservoir
104663 . PLUG, pipe
101864 . SCREW, cap
15M442 . GASKET, pump
100214 . WASHER, lock
247538 KIT, installation control module
112581 . ADAPTER, male
121207 . MODULE, hydraulic control
115775 . VALVE, 3-way solenoid
115773 . VALVE, flow regulating
121206 . VALVE, pressure reducing
115757 . ADAPTER, straight thread
115758 . ADAPTER, straight thread
115760 . ADAPTER, straight thread
115763 . ADAPTER, straight thread
115776 . HOSE, 3/4"X3/4" NPT
115829 . UNION, swivel, 90 degree
160327 . UNION, adapter 90 degree
207648 . UNION, adapter, 90 degree.
238370 . HOSE, coupled, 1 ft.
802072 . GAUGE, pressure
108984 . PLUG, hollow, hex
100214 . WASHER, lock
110384 . SCREW, cap, hex hd
158256 . UNION, swivel
156849 . PIPE, nipple
162505 . FITTING, union swivel
210657 . VALVE, ball
150278 . COUPLING, pipe, hex
116746 . FITTING, barbed, plated
116750 . TUBE, nylon
114526 . TEE
118758 . REDUCER
1
1
4
1
6
1
1a
1b
1c
2
247540 PUMP, Dyna-Star 60#,
see manual 312350
247443 PUMP, Dyna-Star 120#,
see manual 312350
247450 PUMP, Dyna-Star 400#,
see manual 312350
243170 KIT, installation, vent valve (page
1
1
1
4a
4b
4c
4d
4e
4f
4g
4h
4j
4k
4m
4n
4p
4q
4r
4s
4t
4u
5
5a
5b
5c
5d
5e
5f
5g
5h
5j
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
2
1
1
1
1
1
1
1
1
1
1
2a
2b
2c
2d
2e
2f
2g
2h
2i
100505 . BUSHING, pipe
100840 . ELBOW, street
100896 . FITTING, bushing, pipe
111801 . SCREW, cap, hex hd
115122 . VALVE, pressure relief
161889 . UNION, adapter
157705 . UNION, swivel
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
158212 . BUSHING
115470 . UNION, union, swivel, 90_
162667 . ELBOW, street, pipe
194867 . BRACKET, vent valve
194995 . HOSE, vent; 1/2 in.
238370 . HOSE
2j
2k
2m
2n
2p
2q
3
242063 . VALVE, vent
156684 . UNION, adapter
247575 KIT, reservoir, 60# grease,
241486 KIT, reservoir, 90# grease,
100737 . PLUG, pipe
1
3a
3b
3c
3d
3e
3f
2
1
6
4
1
1
1
108126 . TEE, pipe
110996 . NUT, flanged, hex
111800 . SCREW, cap, flange head
115254 . BREATHER
194868 . GASKET, cover
15R105 . PAIL, reservoir, 60#,
models 247706; 247574
3g
* Installation kits for custom user provided lubricant
reservoirs not shown.
3g
194907 . PAIL, reservoir, 90#,
models 247707; 247444
1
312349G
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Technical Data
Maximum hydraulic input pressure
Pump wetted parts
3500 psi (24.0 MPa, 240 bar)
see manual 312350
Vent valve wetted parts
see manual 309099
Reservoir wetted parts
Maximum delivery @ 60 cpm
steel, buna-n rubber
3
3
1.1 lb/min, 34.8 in /min, 570 cm /min
Regulated hydraulic pressure operating range
Models: 247444, 247574, 247456,
247457, 247970
250 to 350 psi (1.7 to 2.4 MPa, 17.0 to 24.1 bar)
Models: 247706, 247707
Hydraulic flow rate operating range
Maximum hydraulic fluid temperature
Lubricant outlet pressure range
Models: 247444, 247574, 247456,
247457, 247970
250 to 450 psi (1.7 to 3.1 MPa, 17.0 to 31.0 bar)
0.5 to 3.0 gpm (1.9 to 11.4 liter/min)
200°F (93.33°C)
2500 to 3500 psi (17.0 to 24.0 MPa, 170 to 240 bar)
Models: 247706, 247707
Reservoir overflow port size
Reservoir fill port size
2500 to 4500 psi (17.0 to 31.0 MPa, 170 to 310 bar)
Hydraulic inlet port size
Hydraulic tank line size
Lubricant outlet port size
Grease capacity
Model 247444, 247707
Model 247574, 247706
90 lb. (41 kg)
60 lb. (27 kg)
Mounting holes for pump module
Reservoir diameter
six, 7/16 inch holes on 13 7/8 inch bolt circle
12 3/4 inch (324 mm)
Pump module height
Model 247444, 247707
Model 247574, 247706
Electrical requirements
Electrical power requirements
Filtration (hydraulic fluid)
Sound Pressure*
42.75 inch (1086 mm)
35.15 inch (893 mm)
Timed 24 VDC signal
14.7 Watts
10µ (microns) or better
77 dB(A)
*Sound pressure reading taken with pump operating at 66 cycles per minute. Sound pressure measured per
CAGI-PNEUROP, 1971.
18
312349G
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Dimensions
Model 247574
Hydraulic high pressure
inlet 3/8 inch nps swivel
Overflow port
1/2 inch npt
Hydraulic tank
3/4 inch nps swivel
ø15.0 inch
Mounting Diagram
(381 mm)
35.15 inch.
(893 mm)
Lubricant outlet
1/2 inch nps swivel
6- 7/16 inch holes
13 7/8 inch bolt circle
15.0 inch
(381 mm)
ti10646a
Fill port 1/2 inch npt
Model 247444
Hydraulic high pressure
inlet 3/8 inch nps swivel
Overflow port
1/2 inch npt
Hydraulic tank
3/4 inch nps swivel
Mounting Diagram
ø15.0 inch
(381 mm)
Lubricant outlet
1/2 inch nps swivel
42.75 inch
(1086 mm)
6-7/16 inch holes
13-7/8 inch bolt circle
Fill port 1/2 inch npt
15.0 inch
(381 mm)
312349G
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Dimensions
Model 247706
Lubricant outlet
1/2 inch
Hydraulic high pressure
inlet 3/8 inch nps swivel
Pressure Relief Kit 247902
Overflow port
1/2 inch npt
Hydraulic tank
3/4 inch nps swivel
Mounting Diagram
ø15.0 inch
(381 mm)
35.15 inch
(893 mm)
6- 7/16 inch holes
13 7/8 inch bolt circle
Fill port 1/2 inch npt
15.0 inch
(381 mm)
ti11451
Model 247707
Lubricant outlet
1/2 inch
Hydraulic high pressure
inlet 3/8 inch nps swivel
Pressure Relief Kit 247902
Hydraulic tank
3/4 inch nps swivel
Overflow port
1/2 inch npt
42.75 inch
(1086 mm)
Mounting Diagram
ø15.0 inch
(381 mm)
6-7/16 inch holes
13-7/8 inch bolt circle
15.0 inch
(381 mm)
Fill port 1/2 inch npt
ti11452
20
312349G
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Notes
312349G
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
To place an order, contact your Graco distributor or to identify the nearest distributor call,
Toll Free: 1-800-533-9655, Fax: 612-378-3590
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 312349
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2007, Graco Inc. is registered to I.S. EN ISO 9001
Revised 10/2010
22
312349G
Download from Www.Somanuals.com. All Manuals Search And Download.
|