IntelliG™ 1000
Model 3024 and 3024H
GARAGE DOOR OPENER
OPERATION AND MAINTENANCE MANUAL
Includes INTELLICODE® 2 Remote Control. Safe-T-Beam® System must be installed to close door.
For use only with residential sectional or one piece overhead garage doors.
Homelink® and Car2U® compatible.
For Answers and Assistance:
1.800.354.3643
WARNING: To reduce the risk of injury to persons or damage to property – Use this opener only with a one piece
or sectional door.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER
Homelink is a registered trademark of Johnson Controls Technology Company. Car2U is a registered trademark of Lear Corporation. © 2010 The Genie Company PN# 37066500753, 12/2010
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
OVERVIEW OF POTENTIAL HAZARDS
READ THIS SAFETY INFORMATION
CONVENTIONS USED IN THESE INSTRUCTIONS
Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving
objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on you reading
the information in this manual. If you have questions or do not understand the information presented, call your nearest trained
door system technician or visit our website.
The following Safety Alert symbol and signal words are used throughout this manual to call attention to and identify different
levels of hazard and special instructions.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and the word "DANGER", "WARNING", or "CAUTION"
DANGER indicates an imminently hazardous situation which, if NOT avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if NOT avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if NOT avoided, may result in injury or property damage.
The word NOTE is used to indicate important steps to be followed or important considerations.
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Potential Hazard
Effect
Prevention
Keep people clear of opening while Door is moving.
WARNING
Do NOT allow children to play with the Door Opener.
Could result in
Death or Serious
Injury
Do NOT operate a Door that jams or one that has a broken
spring.
Turn OFF power before removing opener cover.
WARNING
When replacing cover, make sure wires are NOT pinched or
near moving parts.
Could result in
Death or Serious
Injury
Opener must be fully grounded.
Do NOT try to remove, install, repair or adjust springs or
anything to which door spring parts are fastened, such as,
wood blocks, steel brackets, cables or other like items.
WARNING
Could result in
Death or Serious
Injury
Installations, repairs and adjustments must be done by
a trained door system technician using proper tools and
instructions.
©2010 The Genie Company
12/2010
2
Download from Www.Somanuals.com. All Manuals Search And Download.
OPENER FEATURES
INTELLICODE® 2 Access Security System
A new generation superior encryption system that enhances the security of the door opener by continuously
changing the access code each time the remote is used. The door opener responds to each new code only once.
An access code copied from a working system and tried again will not control the door opener.
Wall Console, Series III
Operates door opener from inside garage. The Wall Console has an Indicator Light with: Open/Close, Sure-Lock™,
and Independent Light Control buttons.
and Car2U® compatible. Refer to the programming instructions on page 10 and then
follow the HomeLink® or Car2U® instructions in your car owner’s manual.
SAFETY FEATURES
Safe-T-Beam® (STB) Non-Contact Reversing System
Puts an invisible beam across the door opening. The door stops and reverses to the full open position if anything
passes through the beam. LED indicator lights on the powerhead and on the STBs provide a self diagnostic code
if an operational problem exists.
Safe-T-Reverse® Contact Reversing System
Automatically stops and reverses a closing door within two seconds of contact with an object.
Automatic ForceGuard™ Control
Automatically sets the force required to fully open and close the door for maximum safety.
Watch Dog™ Monitoring System
Monitors the Safe-T-Beam® system to ensure proper functionality and will automatically stop and reverse a
closing door if a problem is detected.
Manual Emergency Release
Manually releases door from door opener. Used during a power failure or other emergency to allow manual
opening and closing of door.
SmartSet™ Electronic Programming
Easily adjust the programming to reduce opening speed to a desired rate, vary limits and force, and program new
remotes.
Automatic Lighting System
Two bulb lighting system supplies up to 200 Watts of light for safer evening exits and entries. Turns ON when
door is activated and automatically turns OFF 4 minutes later.
Integrated Motion Detection (Not available on all models)
Select units have motion detection built into the powerhead. Lights automatically turn ON when motion is
detected for much safer movement through the garage. Lights will turn OFF after 4 minutes of no motion.
©2010 The Genie Company
12/2010
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Section ....................................................................................Page
Safety Information .................................................................................................... 2
Opener Features & Safety Features................................................................... 3
Table of Contents ....................................................................................................... 4
Installation
Important Installation Instructions ........................................................5
1 Programming Limits & Force.............................................................6-7
Contact Reverse Test........................................................................................... 8
2 Program IntelliCode® 2 Remote to Powerhead............................9
Programming HomeLink®, Car2U®, IntelliCode® 1 remotes or wireless
keypads ................................................................................................................10
Reference
3 Typical Installed Illustrations ................................................................ 11-13
Powerhead & Rail Assembled View ............................................................11
Typical Sectional Door Installation ............................................................12
Typical One Piece Door Installation ...........................................................13
4 Overview of Powerhead Controls ..............................................................14
5 Overview of Remotes and Options...................................................... 15-16
Lost or Stolen Remote - Clearing Memory..................................................15
IntelliCode® Features........................................................................................16
Previously Installed Openers ..........................................................................16
6 Maintenance & Troubleshooting ......................................................... 17-26
Important Safety Instructions........................................................................17
Routine Monthly Maintenance .....................................................................18
Door Balance (Spring Tension) ......................................................................18
Safe-T-Beam® System Check..........................................................................18
Contact Reverse Test.........................................................................................18
Change Light Bulbs...........................................................................................19
Motion Detector - Overview...........................................................................19
Reset - Open/Close Travel Limit .....................................................................19
Carriage Engage/Disengage..........................................................................19
Wall Console - Overview..................................................................................20
Optional Dual Wall Console - Installation .................................................20
Remote Battery Replacement ........................................................................21
Speed Adjustment Guide.................................................................................22
Force Adjustment Guide ..................................................................................23
Troubleshooting Guide - Operation ..................................................... 24-25
Troubleshooting Guide - Powerhead LEDs ................................................25
Reference - Wiring Diagram ..........................................................................26
Warranty ......................................................................................................................27
OPENER MUST BE INSTALLED WITH THE INCLUDED
WALL CONSOLE.
Safe-T-Beam® SAFETY REVERSE SYSTEM MUST BE
INSTALLED TO CLOSE DOOR.
©2010 The Genie Company
12/2010
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Begin here after the opener's physical assembly
and installation has been completed.
There are no assembly or installation steps included in this manual. Contact
your Genie® Professional Dealer for an installation poster, if required, or visit
The following mechanical assembly tasks must be completed before continuing.
Powerhead and rail are bolted to each other (An illustration is shown on page 11)
Example illustrations of the following items are shown on pages 12 and 13
Rail end is attached to a header bracket which is attached to the garage door header
Powerhead is attached to a support frame suspended from the ceiling or ceiling joists
Both pieces of door arms are assembled and are attached to the garage door
Safe-T-Beam® sensors installed and wired
Wall console installed and wired (Shown on page 20)
Carriage is engaged to the chain or belt drive (An illustration is shown on page 11)
Powerhead is plugged into an approved power outlet
Begin programming by setting Limits (see next page.)
A PDF VERSION INSTALLATION POSTER IS AVAILABLE AT WWW.GENIECOMPANY.COM
OR CALL 1-800-35-GENIE TO OBTAIN AN EMAIL PDF FILE
IMPORTANT INSTALLATION INSTRUCTIONS
WARNING:Toreducetheriskofsevereinjuryordeath:
1. READ AND FOLLOW ALL SAFETY, INSTALLATION
AND OPERATION INSTRUCTIONS. (If you have
questions or do not understand an instruction, call
The Genie Company.)
2. Install only on a properly balanced sectional or
one piece garage door. An improperly balanced
door could cause severe injury. Have a trained door
system technician make repairs or adjustments to
cables, spring assemblies, and other hardware before
installing the opener.
5. Do NOT connect the opener to source of power until
instructed to do so.
6. Locate the wall console:
• Within sight of the garage door,
• At minimum height of 5 feet so small children
are not able to reach it, and
• Away from all moving parts of the door.
7. Install the Entrapment WARNING Label next to the
wall console in a prominent location.
8. After installing the opener, the door must reverse
within 2 seconds when it contacts a 1-1/2 inch high
object (or a 2 x 4 board laid flat) on the floor.
3. Remove all ropes and remove or make inoperative all
locks connected to the garage door before installing
opener.
4. Where possible, install the door opener 7 feet or
more above the floor. For products having an
emergency release, mount the emergency release 6
feet above the floor.
INFRARED PROTECTION FUNCTION
1. When garage door is opening, its movement will not be influenced if the Safe-T-Beam® is
obstructed.
2. If the Safe-T-Beam® is obstructed before the garage door fully closes, the door will not close.
3. When the garage door is closing, if Safe-T-Beam® is interrupted by person or obstacle, the garage
door will stop its downward travel and reverse automatically to its fully opened position.
4. Remove Safe-T-Beam® obstruction.
5. If the Safe-T-Beam® System fails, loses power, or is installed improperly, press and hold the wall
console "open/close" button until the door reaches its fully closed position. If you release the
"open/close" button on the wall console during the closing movement the door will reverse
automatically to its fully opened position.
©2010 The Genie Company
12/2010
5
Download from Www.Somanuals.com. All Manuals Search And Download.
+
—
T
S E
P R O G R A M
NOTICE
P
U
L
L
D
O
W
N
O
N
H
A
N
D
L
E
+
+
—
—
T
S E
S E
R A M
P R O G R A M
T
S E
P R O G R A
©2010 The Genie Company
12/2010
6
Download from Www.Somanuals.com. All Manuals Search And Download.
—
T
S E
O G R A M
P R
+
—
O
N
H
A
N
D
L
E
NOTC
P
U
L
L
D
O
W
N
T
S E
M
R A
—
T
S E
O G R A M
P R
©2010 The Genie Company
12/2010
7
Download from Www.Somanuals.com. All Manuals Search And Download.
©2010 The Genie Company
12/2010
8
Download from Www.Somanuals.com. All Manuals Search And Download.
+
—
T
S E
P R O G R A M
+
—
T
S E
P R O G R A M
©2010 The Genie Company
12/2010
Download from Www.Somanuals.com. All Manuals Search And Download.
9
+
—
T
S E
P R O G R A M
+
—
T
S E
P R O G R A M
©2010 The Genie Company
12/2010
10
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCE - POWERHEAD & RAIL ASSEMBLED VIEW
RÉFÉRENCE – VUE DE LA TÊTE D’ALIMENTATION & DU RAIL ASSEMBLÉ
REFERENCIA - VISTA DEL CABEZAL ELÉCTRICO Y RIEL ENSAMBLADOS
N O T I C E
P
U
L
L
D
O
W
N
O
N
H
A
N
D
L
E
I
F
D
O
O
R
B
E
C
O
M
E
S
O
B
S
T
R
U
C
T
E
D
NOTE: Use wall console and safety sensors provided with this unit. Do NOT substitute wall console or safety sensors.
REMARQUE: Utilisez la console sur le mur et les capteurs de sécurité fournis avec cet appareil. NE PAS substituer la console du mur ou les capteurs de sécurité.
NOTA: Use la consola de pared y los sensores de seguridad proporcionados con esta unidad. NO sustituya la consola de pared ni los sensores de seguridad.
©2010 The Genie Company
12/2010
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3
TYPICAL SECTIONAL DOOR INSTALLATION
FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM
INSTALLATION TYPIQUE SUR UNE PORTE SECTIONELLE.................................POUR OBTENIR DE L’AIDE-1-800-35-GENIE
INSTALACIÓN HABITUAL DE UNA PUERTA SECCIONAL................................. PARA OBTENER AYUDA, LLAME AL 1-800-35-GENIE
*If required direct wiring of power supply to opener must be installed by a licensed electrician. Power cord must reach
grounded outlet without use of extension cord.
**Le câblage direct de l'alimentation d'énergie à l'ouvreur doit être installé s'il y a lieu par un électricien autorisé. Le cordon de
secteur doit atteindre la sortie au sol sans utilisation de corde de prolongation.
***Si es necesario, un electricista certificado debe instalar el cableado directo del suministro de energía al abre puertas. El cable eléctrico
debe llegar al enchufe con conexión a tierra sin utilizar un cable de extensión.
TYPICAL SUPPORT BRACKET (NOT PROVIDED)
OPTIONAL - HEADER BRACKET MOUNTING
BOARD
PLANCHE DE MONTAGE FACULTATIVE POUR SUP-
PORT D’EMBASE
SUPPORT TYPIQUE (NON FOURNI)
ESCUADRA DE SOPORTE TÍPICA (NO SE INCLUYE)
TABLERO DE MONTAJE OPCIONAL DE SOPORTE DEL
UMBRAL
BRACING
ATTACHE
ARRIOSTRAMIENTO
POWER CORD* TO 120V
GROUNDED OUTLET
CÂBLE D’ALIMENTATION** À PRISE
DE CONTACT DE 120V À CONTACT
DE MISE À LA TERRE
CABLE DE ALIMENTACIÓN*** A
UN TOMACORRIENTE DE 120 V
CONECTADO A TIERRA
EXTENSION SPRING
RESSORT DE TRACTION
RESORTE DE EXTENSIÓN
OR / OU / O
R NOTICEU
IF
D
O
O
B
E
C
O
M
E
S
O
B
S
T
R
C
T
E
D
P
U
L
L
D
O
W
N
O
N
H
A
N
D
L
E
TORSION SPRING
RESSORT DE TORSION
RESORTE DE TORSIÓN
NOTE: For Low Headroom
installations do NOT reduce door
arm lengths by cutting door arms.
To clear door, reposition door
arms with greater angle.
REMARQUE: Pour les installations
à basse hauteur, ne PAS réduire la
longueur du bras de la porte en
coupant les bras de la porte. Pour
dégager la porte, repositionnez les
bras de la porte à un plus grand
angle.
NOTA: Para instalaciones a alturas
bajas, NO reduzca las longitudes de
los brazos de la puerta cortándolos.
Para despejar la puerta, vuelva a
colocar los brazos de la puerta en otra
posición con un ángulo mayor.
DOOR ARM
BRAS DE LA PORTE
BRAZO DE LA PUERTA
SAFE-T-BEAM® SENSORS
PALPEURS de SAFE-T-BEAM®
SENSORES SAFE-T-BEAM®
FIG. 3-1
MAX. 6" - MIN. 5"
6 po (15 cm) MAX. -
5 po (12,7 cm) MIN.
MAX. 6" - MIN. 5"
©2010 The Genie Company
12/2010
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TYPICAL ONE PIECE DOOR INSTALLATION
........... FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM
.............POUR OBTENIR DE L’AIDE-1-800-35-GENIE
INSTALLATION TYPIQUE D’UNE PORTE DE GARAGE D’UNE PIÈCE
INSTALACIÓN HABITUAL DE PUERTA DE UNA SOLA PIEZA................................... PARA OBTENER AYUDA, LLAME AL 1-800-35-GENIE
*If required direct wiring of power supply to opener must be installed by a licensed electrician. Power cord must reach
grounded outlet without use of extension cord.
**Le câblage direct de l'alimentation d'énergie à l'ouvreur doit être installé s'il y a lieu par un électricien autorisé. Le cordon de
secteur doit atteindre la sortie au sol sans utilisation de corde de prolongation.
***Si es necesario, un electricista certificado debe instalar el cableado directo del suministro de energía al abre puertas. El cable eléctrico
debe llegar al enchufe con conexión a tierra sin utilizar un cable de extensión.
TYPICAL SUPPORT BRACKET (NOT PROVIDED)
SUPPORT TYPIQUE (NON FOURNI)
ESCUADRA DE SOPORTE TÍPICA (NO SE INCLUYE)
HEADER BRACKET MOUNTING BOARD (not provided)
PLANCHE DE MONTAGE FACULTATIVE POUR SUPPORT
D’EMBASE (non fourni)
TABLERO DE MONTAJE DE SOPORTE DEL UMBRAL
(no se proporciona)
POWER CORD* TO 120V
GROUNDED OUTLET
CÂBLE D’ALIMENTATION**
À PRISE DE CONTACT DE
120V À CONTACT DE MISE
LIFT SPRING
RESSORT DE LEVAGE
RESORTE DE ELEVACIÓN
À LA TERRE
IF
D
O
O
R
B
E
C
O
M
E
S
O
B
S
T
R
U
C
T
E
D
P
U
L
L
D
O
W
N
O
N
H
A
N
D
L
E
CABLE DE ALIMENTACIÓN***
A UN TOMACORRIENTE DE
120 V CONECTADO A TIERRA
FIG. 3-2
SAFE-T-BEAM® SENSORS
PALPEURS de SAFE-T-BEAM®
SENSORES SAFE-T-BEAM®
WARNING
To reduce the risk of injury to persons or damage to property -
Use this opener only with a one piece or sectional door.
AVERTISSEMENT
Pour diminuer le risque de blessures corporelles ou
d’endommagement matériel - Utiliser cet l’ouvreur uniquement
avec les portes à section.
ADVERTENCIA
Para reducir el riesgo de lesión a las personas o daños a la propiedad
- utilice este abre puertas solamente con una puerta de una pieza o
seccional.
ONE PIECE DOOR
PORTE D’UNE PIÈCE
PUERTA DE UNA SOLA PIEZA
SECTIONAL DOOR
PORTE SECTIONELLE
PUERTA SECCIONAL
©2010 The Genie Company
12/2010
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OVERVIEW OF POWERHEAD CONTROLS
4
This section describes the simple programming
Programming Overview
functions. Use this page to familiarize yourself with the
buttons and LED indicators used to program the opener.
NOTE: These and buttons are for programming use
only. Do NOT use these buttons to operate the opener.
There are four Powerhead program menus:
Remote Program (Default menu)
Limits Program
Speed Program*
Force Program*
PROGRAM
+
Programming steps for Limits and remotes are found on
pages 6 through 10.
*Force and Speed settings are set at the factory and do
not normally require adjustment programming. Custom
programming instructions for Speed and Force are
located in the Troubleshooting Section of this manual.
—
T
SE
Programming
buttons location
To garage door
on powerhead.
FIG. 4-1 Locate programming buttons
There are three programming buttons and two lights
(LEDs) on the powerhead.
These are the basic steps to enter into the four
programming menus:
PROGRAM
Open
Travel
Button
Close
Travel
Button
ROUND
LED Indicator
(Light)
1. Press and hold until both BLUE lights come ON
SET
then release.
PROGRAM
Facing
Garage Door
2. Both LEDs go out and Round BLUE light comes
ON. You are in the Program Menus at the Remote
Programming.
By using the or the button you can navigate to
the Limits, Speed, or Force program menus and the
LED display will change accordingly.
SET
LONG
Each program menu has a specific LED display.
LED Indicator
(Light)
Press Program
LED Display
FIG. 4-2 Programming buttons
Each of the buttons are used to enter and complete
the setup programming. The LEDs indicate status or a
function change by illuminating ON, OFF, or ON flashing
in one of three different colors: BLUE, RED, or PURPLE.
Default Remote Round Blue
Limits
X2 Speed
X3 Force
Long Blue
Round Blue
Round Red
Throughout the instructions in this manual the buttons
and LEDs are also displayed as icons.
&
Long Blue
Buttons
Name
Shape
Use
PROGRAM
3. Press PROGRAM button to enter into the program menu
Program button
Enters into and selects
programming menus
SET
functions.
SET
If you have entered into an unwanted program menu
and are not sure where you are - do not press any
buttons for 30 seconds. The programming function
will time out after 30 seconds if there is no key stroke
activity.
Close Travel button
multi-function;
moves door, advances
through menus
Open Travel button
multi-function;
moves door, advances
through menus
LED Colors
Round Red
Round Purple
Round Blue
and
Long Red
and
and
Long Purple
Long Blue
©2010 The Genie Company
12/2010
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OVERVIEW - REMOTES AND OPTIONS
5
LOST OR STOLEN REMOTE - CLEARING MEMORY
WARNING
Clearing remotes from powerhead memory will
clear ALL programmed remotes and wireless
keypad.
NOTE: Follow the PROGRAM REMOTE TO
POWERHEAD steps to re-enter remaining or new
remotes. See page 9.
A moving door can cause serious injury or death.
1. Keep people clear of opening while door is
moving.
2. Do NOT allow children to play with opener,
including wall console, remote, or wireless
keypad.
3. During programming, the door opener could
begin to run, so keep people and objects away
from the moving door and its parts. To keep the
door from moving, close the door and disconnect
it from the rail carriage by pulling the Emergency
Release Handle. See page 19 for Release Handle
operation.
PROGRAM
+
1. Press PROGRAM and hold
—
T
SE
SET
until both lights
come ON BLUE.
Release button.
Three Button
Remote
2. Lights go out and Round
BLUE light comes ON.
PROGRAM
3. Press again and
SET
PROGRAM
long LED flashes
+
—
PURPLE.
T
SE
FIG. 5-1 Remote
See page 21 for battery changing instructions.
OGRAM
PR
+
4. Press both and
—
T
FCC and IC CERTIFIED
SE
simultaneously on the
powerhead and hold until
both LEDs flash BLUE.
This device complies with FCC Part 15 and RSS
210 of Industry Canada. This equipment has been
tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide
reasonable protection against harmful interference
in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which may be determined
by turning the equipment OFF and ON, the user is
encouraged to try to correct the interference by
one or more of the following measures:
• Verify memory is cleared. Press a remote
button that was previously programmed to
the powerhead. Remote will not activate door
opener.
• Garage door opener will operate normally using
wall console.
• Program remaining or new remotes as shown
on page 9. Your door opener will no longer
recognize any signal received from the missing
remote, or any other which has not been
reprogrammed to the powerhead.
• Re-orient or relocate the receiver antenna.
• Increase the separation between the opener and
receiver.
• Connect the opener into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult your local dealer.
©2010 The Genie Company
12/2010
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTENTION
If your garage door opener has a Serial Number sticker which
looks like this, in which the first two numbers are 10 or higher,
your opener is equipped with INTELLICODE®2.
MODEL AC SR3
FCC ID: B8Q AC SR3
IC: 2133A-CSD1D
THE GENIE COMPANY
Residential Door Operator
120V. 60HZ. 5A
S/N:10XXXXXXXXXXXX
FOR HELP CALL 1-800-35GENIE OR WWW.GENIECOMPANY.COM
Programming remote to previously installed
IntelliCode® 1 Genie® garage door openers
If you have another garage door opener that does NOT have
a Serial Number like this, then you will be using the
INTELLICODE® 1 setting on your remote to operate that opener.
Remotes provided with this unit can operate other
(IntelliCode® 1) models of Genie® garage door
openers. The default IntelliCode® 2 setting must
be changed to IntelliCode® 1. (Follow these same
steps to change IntelliCode® 1 back to IntelliCode®
2.)
INTELLICODE® FEATURES
Other models of Genie® garage door openers,
remotes, and wireless keypads use
IntelliCode® 1 signals to communicate. Remote(s)
provided with this unit will transmit either
IntelliCode® 1 or IntelliCode® 2 signals.
The LED color displayed on the remote indicates
the IntelliCode® mode.
Remote(s) contained in this package are preset
to IntelliCode® 2 and can be configured to
communicate with previously installed
IntelliCode® 1 openers. This dual IntelliCode®
option allows one IntelliCode® 2 remote to operate
different models of The Genie Company garage
door openers.
Red = IntelliCode® 1 / Green = IntelliCode® 2
1. Select a button on the remote that has NOT been
programmed to the
new powerhead.
2. Press and hold that
button for 10 seconds.
Both Red and Green
This new Genie® garage door opener will ONLY
accept signals from a remote sending IntelliCode®
2 signals (see page 9) or a Genie® brand
IntelliCode® 1 remote that has been programmed
to the opener using a new IntelliCode® 2 remote
(see page 10).
10 SECS
LEDs come ON and stay
ON.
NOTE: Other remotes not enabled with Genie®
IntelliCode® 2 will not operate this opener.
3. Press the same button twice
to toggle IntelliCode®
Use this
selection from IntelliCode® 2
to IntelliCode® 1.
If you have ...
IntelliCode®
programming
One or more IntelliCode® 2
openers with a maximum 3
different openers
Use IntelliCode®
2
4. Press the same button again
to confirm toggle. The
Mixture of openers
Use IntelliCode®
IntelliCode® selection for this
button is set to IntelliCode® 1.
manufactured between 1997 2 and/or 1
and 2010 (IntelliCode® 1) and
new IntelliCode® 2 openers
One or more openers
manufactured between 1997
and 2010 (IntelliCode® 1)
Use IntelliCode®
1
5. Take the remote to the older Genie® garage door
opener and follow that opener's instructions to
program a new remote.
NOTE: A maximum of 3 different openers can be
programmed to a 3 button remote.
Repeat for other Genie® garage remote(s) as
necessary.
Three button
remote
Red LED
Green LED
©2010 The Genie Company
12/2010
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSMITTER COMPLIANCE STATEMENT
Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture.
No warranty is made that they comply with all legal requirements of any other jurisdiction. If transmitters
are to be used in another country, the importer must determine compliance with any local laws and
regulations which may differ from United States and Canadian requirements prior to use.
Los transmisores cumplen con todas las reglamentaciones legales de los Estados Unidos y del Canadá,en
la fecha de fabricación. Ninguna garantía se da que cumplan con todas las reglamentaciones legales de
ninguna otra jurisdicción. Si los transmisores se van a utilizar en otro país,el importador debe determinar
si cumplen con las reglamentaciones y leyes locales que puedan ser diferentes a las reglamentaciones de
los Estados Unidos y del Canadá, antes de usar los mismos.
Les émetteurs sont conformes à la réglementation américaine et canadienne à compter de leur date de
fabrication. Aucune garantie n’est stipulée indiquant qu’ils sont conformes à toutes les prescriptions
juridiques d’autres autorités. Si les émetteurs sont utilisés dans d’autres pays, il incombe à l’importateur
d’en déterminer leur conformité aux lois et règles locales pouvant différer de celles des États-Unis et du
Canada avant toute utilisation desdits émetteurs.
Sendegeräte entsprechen allen gesetzlichen Bestimmungen in den USA und Kanada zum Zeitpunkt der
Herstellung. Wir übernehmen keine Gewährleistung für die Einhaltung aller gesetzlichen Bestimmungen
in anderen Ländern. Sollen Sendegeräte in anderen Ländern eingesetzt werden, so muss der Importeur
vor dem Gebrauch sicherstellen,dass die Sendegeräte auch solchen lokalen Bestimmungen entsprechen,
welche von den Bestimmungen der USA und Kanadas abweichen.
MAINTENANCE & TROUBLESHOOTING
FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM
6
If you have any questions, please do not hesitate to contact customer service at: 1-800-35-GENIE
IMPORTANT SAFETY INSTRUCTIONS
WARNING:Toreducetheriskofsevereinjuryordeath:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Never let children operate or play with the door controls. Keep the remote away from children.
3. Always keep the moving door in sight and away from people and objects until the door is completely closed. NO
ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
4. NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.
5. Test opener monthly. The door MUST reverse on contact with a 1-1/2" high object (or a 2" x 4" board laid flat)
at the center of the doorway on the floor. After adjusting either the force or the limit of travel, retest the door
opener. Failure to adjust the opener properly may cause severe injury or death.
6. When possible, use the emergency release only when the door is closed. Use caution when using this release
with the door open. Weak or broken springs are capable of increasing the rate of door closure and increasing the
risk of severe injury or death.
7. KEEP DOORS PROPERLY BALANCED. See your garage door Owner’s Manual. An improperly balanced door
increases the risk of severe injury or death. Have a trained door system technician make repairs to cables, spring
assemblies, and other hardware.
8.
SAVE THESE INSTRUCTIONS.
©2010 The Genie Company
12/2010
Download from Www.Somanuals.com. All Manuals Search And Download.
17
WARNING
WARNING
• Garage door hardware (springs, cables, brackets,
pulleys, etc.) are under extreme pressure and
tension.
• DO NOT attempt to repair or adjust door
springs or any hardware, and DO NOT OPERATE
garage door automatically or manually if door
is improperly balanced or springs are broken.
– CONTACT A TRAINED DOOR SYSTEM
TECHNICIAN.
Use wall console supplied with opener. Other
approved wall consoles may be available.
Unapproved or incompatible wall consoles can
cause the opener to operate unexpectedly.
Safe-T-Beam® (STB) SYSTEM CHECK
• STB Red and Green LEDs ON steady, system OK
FROM STBs
• STB Red LED flashes
FROM WALL
CONSOLE
– Check for obstruction
– Check alignment
ROUTINE MONTHLY MAINTENANCE
– Verify wire routing from
STBs to STB connection in
powerhead
Basic monthly maintenance tasks.
• Safe-T-Beam® System Check
• Door balance
• Contact reverse
Instructions for these tasks and others are found on
the following pages.
NOT
NOT
USED USED
– Check for signal interference
from another Safe-T-Beam®
unit
STB
BWC
IWC
• No STB Red or Green LED displayed
– Check wiring and wire connections
DOOR BALANCE (SPRING TENSION)
• With the door closed, pull
release handle
DOWN and let go to release door carriage
assembly from drive system.
• Raise door manually approximately 3’- 4’and
release.
– Door should remain stationary or move very
slightly.
– If door moves quickly, CONTACT A TRAINED
DOOR SYSTEM TECHNICIAN.
3’ - 4’
3’ - 4’
• Close the door.
• Verify RED block in carriage is in the up position.
(refer to page 19)
– Operate door using remote or wall console.
– Door will re-attach itself to carriage assembly.
One-Piece Door
Sectional Door
FIG. 6-1 Door balance
CONTACT REVERSE TEST (Monthly test)
The Force and Limit settings MUST be
– Stops after contacting the 2 x 4 board and
does not reverse, it may need an adjustment
to the down limit. Return to pages 6-7 and
repeat steps 1 through 10 to correct down
limit.
• Test again. Repeat as necessary until door
reverses upon contacting board.
COMPLETED before testing. (See pages 6-7)
1. Test.
• Open garage door using wall console.
– Place a 2" x 4" board (laid flat) under center of
garage door opening (Fig. 6-2).
• Close garage door using wall console.
• When door contacts board, the door must
stop (within 2 seconds) and reverse direction
returning to open position.
2. Adjustment.
• If the door:
– Stops before it contacts the 2 x 4 board, it may
simply be responding to an improperly set
down limit. Return to pages 6-7 and repeat
steps 1 through 10 to correct down limit.
FIG. 6-2 2 x 4 under center of door opening
©2010 The Genie Company
12/2010
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CARRIAGE ENGAGE/DISENGAGE
Use Release Handle to manually connect or release
chain or belt bullet to Carriage.
TO RELEASE CARRIAGE:
CHANGE LIGHT BULBS
WARNING
1. Pull handle DOWN then let go.
2. Manually move door until carriage releases from bullet.
3. Raise or lower door manually.
• Observe all safety warning and precautions!
Improper light bulb removal or replacement
could result in Death or Serious Injury.
• Disconnect power from opener before
beginning this task.
• When replacing light cover, make sure wires are
not pinched or near moving parts.
1. Disconnect power to door opener.
• Open powerhead light cover.
• Remove light bulb(s).
NOTICEU
IFD
O
O
RB
E
C
O
M
E
SO
B
S
T
R
C
T
E
D
P
U
L
LD
O
W
NONH
A
N
D
L
E
Release
Handle
DOOR
PULL
• Replace with maximum 100 Watt light bulb(s).
– Do NOT use light bulbs with greater than
100 Watt rating.
TO RECONNECT CARRIAGE:
1. Verify RED block is in the UP position.
2. Manually move door until carriage engages bullet.
3. Raise or lower door using remote or wall console.
• Close powerhead light cover.
2. Reconnect power to door opener.
• Test light operation.
FIG. 6-3 Carriage Release
MOTION DETECTOR* - OVERVIEW
(Not available on all models)
Powerheads equipped with a motion detector
sensor provide additional security when
exiting or entering the garage area.
*This sensor works by detecting body heat. Range of detection may be
reduced when the temperature in the garage is close to body temperature.
NOTE: Detector positioning on the powerhead provides
for monitoring below the powerhead.
OPERATION
• Detector sensor is always ON. There are NO user
controls or adjustments.
• Lights automatically turn ON when a change is
detected and will turn OFF after 4 minutes of no
change.
• Motion detector sensor will not turn OFF lighting
turned ON at the wall console.
• Lighting turned ON at the wall console will remain
ON until wall console turns lighting OFF or opener
is used.
DOOR
Motion Detector
RESET - OPEN/CLOSE TRAVEL LIMIT
ENGAGE
(for installation)
TO REENGAGE PULL
DOWN AND TOWARD
POWERHEAD THEN
LET GO
DISENGAGE
(for installation)
TO DISENGAGE
PULL DOWN AND
TOWARDS DOOR
THEN LET GO
Performing all ten (10) Limits/Force setting steps
(pages 6-7) erases previous Limits/Force settings.
NOTE: The opener will not close the door
automatically unless the Safe-T-Beam® System is
installed and Limits are programmed.
TO RELEASE or RECONNECT CARRIAGE,
PULL DOWN AND LET GO
FIG. 6-4 Carriage Release (cut away view)
©2010 The Genie Company
12/2010
19
Download from Www.Somanuals.com. All Manuals Search And Download.
This opener has a Serial Number sticker in which the serial
numbers begin with 10 or higher.
Open/Close Button
Open and closes door from inside garage
ATTENTION
looks like this, in which the first two numbers are 10 or higher,
your opener will operate using this Series III wall control.
Sure-Lock™ Button
If your garage door opener has a Serial Number sticker which
– LOCK disables controls
after door is completely
closed
MODEL AC SR3
FCC ID: B8Q AC SR3
IC: 2133A-CSD1D
THE GENIE COMPANY
Residential Door Operator
120V. 60HZ. 5A
S/N:10XXXXXXXXXXXX
– UNLOCK allows controls to
work normally
FOR HELP CALL 1-800-35GENIE OR WWW.GENIECOMPANY.COM
Follow the instructions on this page.
Indicator Light
Wall consoles from other manufacturers may not work with
openers of these serial number groups. Genie® Series I wall
buttons and Series II wall consoles will not work with openers
of this serial number group.
Red indicator light is always ON
When Sure-Lock™ is ON the
indicator light flashes
Independent Light Control Button
Controls door opener lights from inside garage
WALL CONSOLE - OVERVIEW
Use only the Series III wall console provided with this
unit.
Wall console has three buttons and one indicator light.
Indicator Light
Indicator light will display Red when wall console is
properly wired and Sure-Lock™ is OFF. When Sure-
Lock™ is ON indicator light flashes.
Tip: If indicator light on wall console comes ON, but
there is NO
FROM STBs
FROM STBs
FROM WALL
CONSOLE
FROM WALL
CONSOLE
operation from
buttons - verify
wall console
wire routing
at powerhead
connector.
Open/Close Button
Use this button to open or close garage door. When
Sure-Lock™ is ON the Open/Close button will CLOSE
door only. Note: Constant button pressure in the
CLOSE mode will override error responses in the
powerhead and close door.
NOT
USED USED
NOT
STB
BWC
IWC
Independent Light Control Button
OPTIONAL DUAL WALL CONSOLE - INSTALLATION
Use this button to turn powerhead lights ON.
Powerhead lighting will remain ON until this button
is pressed again or a door action has been completed.
Note: If opener has a Motion Detector sensor the
sensor will keep powerhead lights ON as long as
motion is detected.
Use only a Series III wall console when adding a
second wall console. The optional second Genie®
Series III wall console must be purchased separately.
TO
TO WALL CONSOLE #1
POWERHEAD
Sure-Lock™ Button
FROM STBs
FROM WALL
CONSOLE
When Sure-Lock™ is ON the powerhead cannot be
activated by the wall console or a remote.
• Press and hold for 5 seconds (or until Indicator
Light flashes) to activate Sure-Lock™.
• Press and release to turn Sure-Lock™ OFF.
B/W
W
W
B/W
NOT
USED USED
NOT
STB
BWC
IWC
WALL
CONSOLE #2
WALL
CONSOLE #1
Wire connector
on Powerhead
OR
BOTH TO POWERHEAD
FROM STBs
FROM WALL
CONSOLE #1
FROM WALL
CONSOLE #2
NOT
NOT
USED USED
B/W
W
W
B/W
STB
BWC
IWC
Wire connector on
Powerhead
WALL
CONSOLE #2
WALL
CONSOLE #1
©2010 The Genie Company
12/2010
20
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAIN OR BELT - TENSION ADJUSTMENT
WARNING
Belt
• Observe all safety warning and precautions!
• Disconnect power from opener and disconnect
carriage in rail from bullet before beginning this
task.
Adjustment required
Correctly adjusted
Belt
Approx. 1/8"
Visually inspect the chain or belt every 6 months.
NOTE: Tension adjustments should be made with the
door in the down position and the carriage released.
Belt at center of rail
• At the center of the rail the chain or belt should
not be resting on the rail. See adjustment
illustration on right.
BELT
– With the bullet NOT engaged to the carriage,
tighten adjustment nut until chain/belt does
not, at the center of the rail, rest on rail. Do NOT
overtighten.
Chain
Adjustment required
• Is there rust on chain or frayed edges on belt?
– Contact a trained door system technician for
chain/belt replacement.
• Are there kinks or twists in the chain or belt?
– Contact a trained door system technician for
chain/belt replacement.
Chain
Approx. 1/8"
Correctly adjusted
Chain at center of rail
CHAIN
Tighten nut to increase
tension on chain or belt
REMOTE BATTERY REPLACEMENT
Replace remote battery with a CR 2032 coin cell battery.
1. Open the remote case using a washer or coin that fits
into the slot at the top of the remote.
2. Replace battery.
3. Align components and snap case closed.
©2010 The Genie Company
12/2010
Download from Www.Somanuals.com. All Manuals Search And Download.
21
ADJUSTMENT GUIDE - SPEED SETTINGS
FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM
Speed settings are pre-programmed at the factory
for the maximum speed. Speed settings should not
need adjustment with this unit.
However, travel speed for the opener in both the
open and close directions can be adjusted to slower
speeds to minimize normal wear for heavy sectional
doors.
CHANGE SPEED SETTING
Use this guide to ADJUST powerhead SPEED settings.
There are three (3) Speed settings available on this
unit for the open and close directions. Door type
(one piece or sectional), door weight and balance,
and condition of door components / track affect
door speed. Speed adjustment may not be available
for some installations depending on these factors.
NOTE: One piece doors are automatically set during
Limits programming to the slowest speed and
opener speed cannot be reset for one piece doors.
PROGRAM
1. Press on the powerhead and hold until both
SET
lights turn steady ON. Release button.
Lights go out and Round BLUE light comes ON.
2. Press two times and the Round BLUE and Long
BLUE lights come ON.
PROGRAM
3. Press once to enter the Speed Programming
SET
menu. The round LED will flash BLUE 3 times,
then the current Speed setting for UP travel will
display on the LEDs. See table below.
4. Press to raise or to lower UP Speed settings
within the available range.
NOTE: Faster door speeds may not be available.
PROGRAM
5. Press to set UP Speed level. The long LED will
SET
flash BLUE 3 times, then the current Speed setting
for DOWN travel will display on the LEDs.
6. Press to raise or to lower DOWN Speed
settings within the available range.
NOTE: Faster door speeds may not be available.
PROGRAM
7. Press to set DOWN Speed level. Both LEDs flash
SET
BLUE to confirm.
Powerhead LEDs
Speed Level
Round LED Long LED
Default LED display is the current Speed setting
Red
Purple
Blue
Red
LED Speed indicator colors
Purple
Blue
Speed Level LED indicator colors
Red
Red
MAXIMUM
MID
ON
ON
Purple
ON
Purple
ON
Blue
ON
Blue
ON
SLOW
©2010 The Genie Company
12/2010
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENT GUIDE - FORCE SETTINGS
FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM
CHANGE FORCE SETTING
CAUTION
Use this guide to ADJUST powerhead FORCE settings.
Door closing force is FACTORY set and requires no
adjustment for normal operation.
• Never increase the door closing force to
compensate for a damaged door or a binding
door track.
• Never adjust force to compensate for a broken
door spring.
NOTE: There are nine (9) force levels.
PROGRAM
1. Press on the powerhead and hold until both
SET
lights turn steady ON. Release button.
Lights go out and Round BLUE light comes ON.
2. Press three times, Round RED light comes ON.
PROGRAM
• Perform monthly CONTACT REVERSE TEST as
described on page 18.
3. Press once to enter the Force Programming
SET
menu. The round LED will flash BLUE 3 times,
then the current Force setting for UP force will
display on the LEDs. See table below.
Force settings are pre-programmed at the factory
and "learned" during the Open/Close Limit settings
steps. Some additional Force may be increased.
For normal use, Force settings should not need
adjustment with this unit.
However, conditions that might suggest an
adjustment is necessary are;
4. (If current UP Force setting is good, skip to Step
5.) Press to increase or to decrease UP Force
settings within the available range.
PROGRAM
5. Press to set UP Force level. The long LED will
SET
flash BLUE 3 times, then the current Force setting
for DOWN force will display on the LEDs.
Doors with very stiff weather seals.
Doors that start down, then STOP and reverse
before they close.
Doors that start up, but STOP before they
completely open.
6. (If current DOWN Force setting is good, skip to
Step 7.) Press to increase or to decrease
DOWN Force settings within the available range.
PROGRAM
7. Press to set DOWN Force level. Both LEDs flash
SET
BLUE to confirm.
Powerhead LEDs
Force Level
Round LED Long LED
Default LED display is the current Force setting
LED indicator colors
OFF,
Blue,
Purple,
Red
Force Level LED indicator colors
Blue
ON
Force Level 1
Force Level 2
Force Level 3
Force Level 4
Force Level 5
Force Level 6
Force Level 7
Force Level 8
Force Level 9
OFF
Blue
ON
OFF
Blue
ON
Blue
ON
Purple
ON
OFF
Purple
ON
OFF
Purple
ON
Purple
ON
Red
ON
OFF
Red
ON
OFF
Red
ON
Red
ON
©2010 The Genie Company
12/2010
Download from Www.Somanuals.com. All Manuals Search And Download.
23
TROUBLESHOOTING GUIDE -
OPERATION
FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM
PROBLEM
WHAT TO DO
• Check power source,
– Plug a lamp into outlet used for powerhead. If lamp works, power source is OK.
– If not, check fuse or circuit breaker.
• If power is OK,
Opener does NOT run
from wall console.
– Check connections at powerhead terminals and at wall console.
– Limits must be set with door arm connected to door.
• Check if wall console Sure-Lock™ is ON. Turn Sure-Lock™ OFF & check operation.
• Check for reversed, broken, or cut wires. Staples can cut insulation and short wires.
Repair or replace.
• Make sure carriage is engaged to chain or belt bullet. See pages 11 and 19. Refer to
Installation poster or download poster from WWW.GENIECOMPANY.COM.
– Ensure carriage is in engaged position. See page 19.
• Check to make sure chain/belt is not broken or OFF its pulley.
• Check FORCE ADJUSTMENT. See page 23.
Opener runs, but door
does NOT move.
Opener works from
wall console, but NOT
from remote.
• Check all remotes.
• Replace remote battery with good one. See page 21.
• Program remote to powerhead. See pages 9 or 10.
• Relocate remote inside car and or point remote at garage door.
• Replace battery. See page 21.
Remote has less than
25 feet operating
• Reposition door opener antenna.
range or no operation. • Remote LED does not come ON with button push - replace battery. See page 21.
• Eliminate possible competing signals (satellite radio, FiOS® TV).
• If a NEW installation, check Door Arm position. Refer to Installation poster or download
Door starts down,
then STOPS and goes
back up.
poster from WWW.GENIECOMPANY.COM.
• Check if Limits are properly set. See pages 6-7.
• Check if Safe-T-Beam® Red LED is flashing. See page 18.
• Check Safe-T-Beam® system for beam obstruction or misalignment of lenses. See page 18.
• Check garage door for binding.
OR
• If an operational problem exists, and opener will not close. The opener can be forced to
close as follows; Press and hold the wall console button until door is completely closed.
• Check for interference from adjacent Safe-T-Beam® units.
• Contact The Genie Company at 1-800-35-GENIE.
Safe-T-Beam® System
malfunction.
Door starts down,
then STOPS before it
is closed.
• Check Safe-T-Beam® wire connections at powerhead. See page 18.
• Check Limits are properly set. See pages 6-7.
• Check CONTACT REVERSE. See page 18.
OR
• Check garage door for binding.
Door will only open.
• Check closing "FORCE" adjustment. See page 23.
• Check Limits are properly set. See pages 6-7.
• Be sure door, opener, and springs are in good repair, properly lubricated and balanced.
• Check opening "FORCE" adjustment. See page 23.
Door starts up, but
STOPS before it is
completely open.
•
WARNING: If you suspect a problem with the garage door hardware or springs,
contact The Genie Company at 1-800-35-GENIE.
• Check Limits are properly set. See pages 6-7.
• Check Sure-Lock™. Sure-Lock™ should be OFF for normal operation. See page 20.
• Check door balance, condition, and door spring.
Door will only run
closed.
• Check opening "FORCE" adjustment. See page 23.
•
WARNING: If you suspect a problem with the garage door hardware or springs,
contact The Genie Company at 1-800-35-GENIE.
• Button stuck on wall console or remote.
• Was a remote lost or stolen? Erase all remotes from powerhead memory and program
new remotes. See page 15.
Door opener starts for
no reason.
©2010 The Genie Company
12/2010
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE -
OPERATION (CONTINUED)..................................................................... FOR HELP-1-800-35-GENIE
PROBLEM
WHAT TO DO
• Be sure all door fasteners are tight.
• Be sure garage door is in good repair, properly lubricated and balanced.
• Be sure opener is in good repair.
Noisy operation.
• Check operating condition of door. See pages 18. Door may need professional repair/
adjustment.
• Is this opener installed on a one piece door? Normal speed for one piece door is
Door opener runs
slow.
lowest speed setting.
• If carriage travel is less than 6 feet, opener configures programming for a one piece
door.
• Check door speed. See page 22.
TROUBLESHOOTING GUIDE -
POWERHEAD LEDs
FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM
Powerhead LED
Possible Problem
Solution
Round LED
Long LED
Normal operation
None required
Check power supply
Contact a trained door system
technician
OFF
OFF
No response from unit
ON/RED/
STEADY
ON/RED/
STEADY
Limits NOT set properly
Program error
Reprogram Limits, see pages 6-7
Unplug unit, wait 5 seconds, plug in
ON/RED/
FLASHING
ON/RED/
FLASHING
Contact a trained door system
technician
Component failure
ON/BLUE/
FLASHING
OFF
OFF
Remote NOT programmed
Program remote, see page 9
Program remote using IntelliCode®
2 remote, see page 9, then program
IntelliCode® 1 remote using
instructions on page 10
ON/PURPLE/
FLASHING
IntelliCode® 1 remote NOT
programmed
Safe-T-Beam® physical
obstruction
Remove obstruction, recheck unit
ON/RED/
FLASHING
OFF
Safe-T-Beam® signal
interference
Check alignment of Safe-T-Beam® pair
and nearest other Safe-T-Beam® pair
Door contact in up or down
travel
Remove obstruction
ON/RED/
FLASHING
OFF
OFF
Door component failure
detected
Check door spring, track, rollers, hinges
and fixtures
ON/RED/
STEADY
DO NOT unplug unit
Wait until LED clears before operating
Thermal cutout
©2010 The Genie Company
12/2010
25
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCE - CIRCUIT WIRING DIAGRAM
FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM
RÉFÉRENCE - DIAGRAMME DE CÂBLAGE DE CIRCUIT
REFERENCIA - ESQUEMA ELÉCTRICO DEL CIRCUITO
........................................................POUR OBTENIR DE L’AIDE-1-800-35-GENIE
...................................................... PARA OBTENER AYUDA, LLAME AL 1-800-35-GENIE
Opener circuit wiring diagram. This wiring diagram is for reference only.
Schéma de câblage de l’ouvreur. Ce schéma de câblage est indiqué à titre de référence uniquement.
Diagrama del circuito del operador. Este diagrama es sólo para referencia.
Opening Cover May Cause Electric Shock.
L’ouverture du couvercle peut entraîner des chocs électriques.
Abrir la tapa puede causar choques eléctricos.
Disconnect power from opener prior to removing cover.
Coupez l’alimentation de l’ouvre-porte avant de retirer le couvercle.
Desconecte la electricidad del abrepuertas antes de quitar la cubierta.
WARNING
AVERTISSEMENT
ADVERTENCIA
POWER CORD
CORDON DE SECTEUR
CABLE ELÉCTRICO
SCREW DRIVE MOTOR
IMPULSIÓN DEL
CHAIN/BELT MOTOR
CADENA/CORREA MOTEUR
CHAÎNE/COURROIE MOTOR
CONNECTOR
CONNECTEUR
CONECTADOR
PRINTED CIRCUIT BOARD
TORNILLO MOTEUR
CIRCUIT IMPRIMÉ
COMMANDE DE VIS MOTOR
CIRCUITO IMPRESO
WHITE
BLANC
BLACK
NOIR
RED
BLANCO
ROUGE
ROJO
NEGRO
RED
ROUGE
ROJO
BLACK
NOIR
NEGRO
BLACK
NOIR
NEGRO
1
2
3
4
GREEN
VERT
VERDE
STB
BWC (IWC or AWC)
1
2
3
4
5
6
STRIPED WHITE
BLANC RAYÉ
STRIPED WHITE
BLANC RAYÉ
CHOKE
BOBINE D'ARRÊT
BOBINA DE CHOKE
BLANCO RAYADO
BLANCO RAYADO
WHITE
BLANC
BLANCO
BLACK
NOIR
WHITE
BLANC
SAFE-T-BEAM®
SAFE-T-BEAM®
SAFE-T-BEAM®
NEGRO
BLACK
NOIR
BLANCO
(Purchased Separately)
NEGRO
INTELLIGENT WALL CONSOLE
CONSOLE INTELLIGENTE DE MUR
CONSOLA INTELIGENTE DE LA PARED
BLACK
NOIR
1
7
6
5
4
3
2
NEGRO
WALL CONSOLE
FIG. 6-5
CONSOLE DE MUR
CONSOLA DE LA PARED
WARNING
MOTION DETECTOR*
OPTICAL SENSOR*
SONDE OPTIQUE
SENSOR ÓPTICO
DÉTECTEUR DE MOUVEMENT
AVERTISSEMENT
DETECTOR DE MOVIMIENTO
ADVERTENCIA
1
2
3
1
2
3
4
RED
ROUGE
ROJO
RED
ROUGE
ROJO
GREEN
VERT
BLACK
NOIR
VERDE
NEGRO
YELLOW
JAUNE
AMARILLO
ELECTRICAL SHOCK
CHOC ÉLECTRIQUE
CHOQUE ELÉCTRICO
*SOME MODELS DO NOT COME WITH THIS FEATURE
QUELQUES MODÈLES NE VIENNENT PAS AVEC CETTE CONFIGURATION
ALGUNOS MODELOS NO VIENEN CON ESTA CARACTERÍSTICA
12/2010
©2010 The Genie Company
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Intelli ™ 1000
Limited Warranty
GMI Holdings, Inc. d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified garage door opener, IntelliG™ 1000 (Model
3024 and 3024H) (“Product”), subject to all of the terms and conditions hereof, that the Product and all components thereof will be free from defects in materials
and workmanship for the following period(s) of time, measured from the date of purchase:
MOTOR/GEARBOX- Seller warrants the motor/gearbox for the LIFETIME* of the product.
BELT- Seller warrants the belt for a period of FIFTEEN (15) YEARS.
CHAIN - Seller warrants the chain for a period of FIVE (5) YEARS.
CORE UNIT PARTS** - Seller warrants all other parts and components of the Core Unit for a period of FIVE (5) YEARS.
ACCESSORIES - Seller warrants all accessories for a period of ONE (1) YEAR.
*Lifetime shall mean for as long as the original purchaser owns the home in which the product is originally installed.
** The Core Unit consists of the powerhead, wired wall control, Safe-T-Beam® system, J-Arm and rail.
Seller’s obligation under this warranty is specifically limited to repairing or replacing, at its option, the Product or any part thereof which is determined by
Seller to be defective during the applicable warranty period. Any labor charges are excluded and will be the responsibility of the purchaser.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty is made to the original purchaser
of the Product only, and is not transferable or assignable. This warranty applies only to Product installed in a residential or other non-commercial application.
It does not cover any Product installed in commercial or industrial building applications. This warranty does not apply to any unauthorized or improper
installation, alteration or repair of the Product, or to any Product or component which has been damaged or deteriorated due to misuse, abuse, neglect,
accident, failure to provide necessary maintenance, normal wear and tear, or acts of God or any other cause beyond the reasonable control of Seller, and does
not cover batteries, missing or damaged parts from clearance or open box sales, or repairs or maintenance to door components.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN TIME TO THE APPLICABLE WARRANTY PERIOD
REFLECTED ABOVE. NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THE LIMITED WARRANTY PERIOD HAS
EXPIRED. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
IN NO EVENT SHALL GMI HOLDINGS, INC. OR ITS PARENT OR AFFILIATES BE RESPONSIBLE FOR, OR LIABLE TO ANYONE FOR, SPECIAL,
INDIRECT, COLLATERAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL DAMAGES, even if Seller has been advised of the possibility of such
damages. Such excluded damages include, but are not limited to, loss of use, cost of any substitute product, or other similar indirect financial loss. Some states
do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Claims under this warranty must be made promptly after discovery and within the applicable warranty period. To obtain warranty service, you must contact
Genie® customer service and provide proof of the date and location of purchase and identification as the original purchaser. Call Genie® Customer Service toll
free at 1-800-354-3643 to speak with a trained representative. Purchaser must allow seller a reasonable opportunity to inspect Product claimed to be defective
prior to removal or alteration of its condition. Upon determination by Seller that the Product or any part thereof is defective during the applicable warranty
period (which may require purchaser to return the Product to Seller at purchaser’s expense), Seller will supply the purchaser with replacement parts or, at its
option, a replacement Product (shipping and handling of any replacement part(s) or replacement Product also at purchaser’s expense). Seller may use new or
reconditioned parts, or a new or reconditioned Product of the same or similar design.
There are no established informal dispute resolution procedures of the type described in the Magnuson-Moss Warranty Act.
PURCHASER:
INSTALLATION ADDRESS:
DATE PURCHASED:
OPENER MODEL:
SERIAL NUMBER:
REMOTE CONTROL MODEL:
DEALER NAME:
DEALER ADDRESS:
P900-228
Download from Www.Somanuals.com. All Manuals Search And Download.
|