Magnum 6K32T & 6K32TRC
6K32T
6K32TRC
Managed Switch
Installation and User Guide
Hardware User Manual
www
.
GarrettCom . com
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide(05/07)
Magnum 6K32T & 6K32TRC
™
Managed Switch Hardware
Installation and User Guide
Part #: 84-00138 (Rev. B)
Trademarks
Ethernet is a trademark of Xerox Corporation
NEBS is a trademark of Telcordia Technologies
UL is a registered trademark of Underwriters Laboratories
GarrettCom, Magnum, Personal Switch, S-Ring, Link-Loss-Learn, Converter
Switch and Convenient Switch are trademarks and Personal Hub is a registered
trademark of GarrettCom, Inc.
GarrettCom, Inc. reserves the right to change specifications, performance
characteristics and/or model offerings without notice.
Important: The Magnum 6K32T & 6K32TRC Managed Switch
contains no user serviceable parts. Attempted service by unauthorized
personnel shall render all warranties null and void. If problems are
experienced with Magnum 6K32T & 6K32TRC Switch products, consult
Section 6, Troubleshooting, of this User Guide.
Copyright © 2007 GarrettCom, Inc. All rights reserved. No part of this
publication may be reproduced without prior written permission from
GarrettCom, Inc.
Printed in the United States of America.
www
.
GarrettCom . com
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide(05/07)
Contacting GarrettCom, Inc
Please use the mailing address, phone and fax numbers and email address listed
below:
GarrettCom, Inc.
47823Westinghouse Dr.
Fremont, CA 94539-7437
Phone (510) 438-9071
Fax (510) 438-9072
email [email protected]
Federal Communications Commission
Radio Frequency Interference Statement
This equipment generates, uses and can radiate frequency energy and if
not installed and used properly, that is in strict accordance with the manufacturer's
instructions, may cause interference to radio communication. It has been tested
and found to comply with the limits for a Class A computing device in accordance
with the specifications in Subpart J of Part 15 of FCC rules, which are designed to
provide reasonable protection against such interference when operated in a
commercial environment. Operation of this equipment in a residential area is
likely to cause interference, in which case the user at his own expense will be
required to take whatever measures may be required to correct the interference.
Canadian Emission
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil respecte toutes les exigences du Réglement sur le matériel du
Canada. Cet appareil est Classe A.
RegulatoryUL60950 Voltage Range:
18-36VDC: 24vdc option
38-60VDC:60vdc option
100-150VDC:125vdc option
100-240Vac- AC option
Test Temp.: 40˚C
www
.
GarrettCom . com
Download from Www.Somanuals.com. All Mainiuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide(05/07)
TABLE OF CONTENTS..........................................................................
Page
1.0
1.1
1.2
2.0
SPECIFICATIONS................................................................................2
Technical Specifications.......................................................................2
Ordering Information ...........................................................................5
INTRODUCTION..................................................................................9
Inspecting the Package and Product.....................................................9
Product Description - Magnum 6K32TRC Managed Switch.............10
2.1
2.2
2.2.1a
Magnum 6K32T Managed Switch Chassis ................................12
2.2.2 Eight-port SFF fiber modules (6K8-MTRJ, 6K8-MLC)..................13
2.2.3 Eight-Port Copper Module, 6K8-RJ45 (MDIX) ............................14
2.2.3a
New PoE(Power Inside), PI6KP8-45RJ (MDIX), 8-port 10/100Mb.....15
2.2.3b New PoE(Power Pass-through) P6KP8-RJ45 (MDIX) 8-port.................16
2.2.4
2.2.5
2.2.6
2.2.7
2.2.8
2.2.9
Six-Port “4 + 2”Combo Modules fiber ST or SC.......................16
Four-Port 10 Mb mm Fiber ST Modules.................................17
Gigabit (1000Mbps) port modules .............................................18
Packet Prioritization, 802.1p QOS .............................................19
Frame Buffering and Flow Control............................................19
Managed Network Software 6K32T & 6K32TRC.....................20
Features and Benefits .........................................................................21
Applications .......................................................................................22
INSTALLATION ................................................................................27
Locating Magnum 6K32T Switches...................................................27
Connecting Ethernet Media................................................................28
2.3
2.4
3.0
3.1
3.2
3.2.1
3.2.2
3.2.3
3.2.4
3.2.5
3.2.6
Connecting Fiber Optic ST-type, “twist-lock”...........................28
Connecting Fiber Optic SC-type, "Snap-In" ..............................29
Connecting Single-Mode Fiber Optic ........................................29
Connecting Twisted Pair (RJ-45,CAT3, CAT5)................................29
Connecting Twisted Pair (CAT-5e or better) ....................................30
Gigabit SFP (Small Form-factor Pluggable) Transceivers.........30
Power Budget Calculations 6K32T & 6K32TRC PM’s..........................32
Table-Top or Shelf Mounting.............................................................34
Rack-mounting (for 19” RETMA)6K32T & 6K32TRC’s..........34
3.2.7
3.3
3.3.1
3.3.2 Rack-mounting, Reverse version of the Magnum 6K32T’s..............35
3.4 Powering the Magnum 6K32T & 6K32TRC Managed Switch .........36
3.4.1 Alarm Contacts for monitoring internal power Traps....................36
3.5 6K32T & 6K32TRC Port Module (6KPM) Installation.....................37
3.5.1 Preparation for Installing and Removing 6KPMs ............................37
3.5.2
3.5.3
3.6
3.6.1
Installing 6KPM Cards in the 6K32T & 6K32TRC...................40
Removing 6KPM Cards .............................................................43
Connecting the Console Terminal to 6K32T & 6K32TRC................44
RS-232 (DB-9) Console Com port (Serial port) pin...................45
4.0
4.1
OPERATION........................................................................................46
Switching Functionality .....................................................................46
Status LEDs........................................................................................47
Auto-Cross (MDIX)Auto-neg for 10/100Mbps RJ-45 ports..............47
4.2
4.3
www
.
GarrettCom . com
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide(05/07)
4.4
5.0
Flow-control, IEEE 802.3x standard..................................................49
6K32T & 6K32TRC MANAGED SWITCH PORT MODULES.....49
Inspecting the Package and Product...................................................50
6KPM Module Description ................................................................50
5.1
5.2
5.2.1
5.2.1a
6KP6-RJMST multi-mode FX-ST “twist lock” Module............51
6KP6-RJ10ST multi-mode FX-ST “twist lock” Combo ............51
5.2.1b 6KP4-F10ST multi-mode FX-ST “twist lock” Module.............52
5.2.1c
5.2.2.
5.2.3
6KP4-FLSTFX multi-mode FX-ST “twist lock” Module.........52
6KP6-RJMSC multi-mode FX-SC “snap-in” Fiber connector ...........53
6KP6-RJSSC Mbps single-mode FX-SC-type, “snap-in”..................54
6KP6-RJSSCL FX-SC-type, “snap-in” connector ............................54
6KP6-RJ10ST FL-ST-type, “twist-lock” connector...........................55
6KP8-MTRJJ Small-Form-factor...............................................55
6KP6-MT10STmode FX Factor ................................................56
6KP8-45MT MTRJ Small-Form-Factor.....................................57
6KP8-MLC LC connector Small- ..............................................57
6KP8-45LC 10/100 Mbps RJ-45 Connector..............................58
6KP8-RJ45 (Twisted Pair), 10/100Mb 8-Port...........................58
New PoE (Power Pass-through)P6KP8V-RJ45 (MDIX).................59
New PoE(Power Inside), model PI6KP8-45RJ (MDIX) .................60
5.2.4
5.2.4a
5.2.5
5.2.5a
5.2.6
5.2.7
5.2.8
5.2.9
5.2.10a.
5.2.10b.
5.2.11 6KP8-45-2MT MTRJ Small-Form-Factor ................................62
5.2.11a 6KP8-45-2LC single-mode FX , LC Small-Form-Factor.......62
5.2.12 GBIC-SXSC Gigabit fiber(1000Mb), multi-mode SC ..............62
5.2.12a
5.2.12b
GBPM-2OTX (Two Gigabit option)......................................63
GBIC-LXSC Gigabit fiber (1000Mb), multi-mode SC .........64
5.2.13 6KM-BLNK ...............................................................................64
6.0
6.1
6.2
TROUBLESHOOTING.......................................................................65
Before Calling for Assistance.............................................................65
When Calling for Assistance..............................................................66
Return Material Authorization (RMA) Procedure..............................66
Shipping and Packaging Information.................................................67
6.3
6.4
APPENDIX A: WARRANTY INFORMATION .........................................67
APPENDIX B : INTERNAL DC POWER SUPPLY OPTIONS.................68
APPENDIX C: INTERNAL DC DUAL-SOURCE POWER OPTION ......71
Revisions
Rev C 05/07: SFP fiber info added and Typo error updated on Temp.
Rev C 10/06: Included 6K32TRC and PoE Modules
Rev B 12/05 : Updated Gigabit options
Rev A 05/05 : Minor updates, Auto-Cross(MDIX)
Rev A 02/05 : Minor updates and tweak on LC connector diagram
Rev A 08/04 : This revision is the initial release of the 6K32T manual.
www
.
GarrettCom . com
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide(05/07)
The Magnum Line
INDUSTRIAL NETWORKING PRODUC TS
"DESIG NED AND MANUFAC TURED IN THE USA"
OVERVIEW
GarrettCom, Inc. offers the premium-quality Magnum™ line of
INDUSTRIAL conectivity products with industry-standard functionality and
built-in fiber configurability. Magnum products are designed for use in
demanding Industrial Grade, Carrier Class, POWER UTILITY and OEM
applications where reliability is a primary consideration.
6K-Series Managed Field Switches, Gigabit, 100 and 10 Mbps, fiber and copper ports, mix-and
match. Features SFF fiber and DC power in 1U units.
DX-Series Serial Device Routers, Ethernet and Serial
4K-Series Switches, 100 and 10 Mbps, copper ports with optional fiber port, with auto-negotiating
full switching performance.
Quad-Series Fiber Switches, 100 & 10Mbps, fiber and copper ports, mixed-speed and mixed-media
types, full switching performance.
mP62 and P62F “Outdoor” Ethernet SwitchES, for temperature uncontrolled locations, 6 10/100
and 2 100Mb fiber ports, can be connected in strings
Mixed-Media Fiber Hub, 16-port, 10/100 auto-sensing
Dual Speed 8-port and 16-port, 10/100 auto-sensing HUBS
Personal Switches, 10/100Mb
8 port dual-speed, Auto-negotiable with fiber option
Personal Hubs, 100Mb or 10/100Mb 8-port, with 2 switched ports (1 fiber built in)
Personal Hubs, 10Mb series 8-port + AUI, stackable to 5 high, + optional BNC of fiber port 8 or 9-
port and 4 or 5-Port Personal Hubs, w/ man. up-link sw.
Media Converters, 10Mb and 100Mb series, All media combinations, incl. fiber ST, SC, mm.,
single mode
The “X-line” of configurable MiXed Media products:
Stackable Concentrators, SNMP optional, 13-Ports
Mini-Concentrators, 7 Ports, Repeaters, 2-Ports
Repeater Port Modules (RPMs), 6 types for Ethernet media
COAX Transceivers, 10Mb series
APR, 07
www
.
GarrettCom . com
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
1.0
1.1
SPECIFICATIONS
Technical Specifications
Performance
Filtering / Forwarding Rate:
Ethernet:14,880 pps
Fast Ethernet: 148,800 pps
Gigabit Ethernet: 1,488,000 pps
Switching Processing Type: Store and Forward with IEEE 802.3x full-
duplex flow -control, non-blocking
Data Rate: 10Mbps,100Mbps and 1000Mbps
Address Table Capacity: 4K node, self-learning with address aging
Packet buffer size : 240KB for 10/100 and 120KB for 1000Mb
Latency: 5 µs + packet time (100 to 100Mbps)
15 µs + packet time (10 to 10 Mbps, and 10 to 100Mbps)
Throughput with 16 10/100 and 4 Glink max- 8.33M pps (Transmit)
Back plane- 2.66Gb/s per slot
Network Standards and Compliance
Ethernet V1.0/V2.0 IEEE 802.3: 10BASE-T,
IEEE 802.3u: 100Base-TX, 100BASE-FX
IEEE 802.3z: 1000BASE-X Ethernet(Auto-negotiation)
IEEE 802.3ab: 1000BASE-X Ethernet
IEEE 802.1p: Priority protocol
IEEE 802.1d: Spanning tree protocol
IEEE 802.1w: Rapid Spanning tree protocol
IEEE 802.1q: VLAN Tagging
IEEE 802.3x: Flow Control
IEEE 802.3ad: Link Aggregation (Trunking)
IEEE 802.1x: Port based Network access control
Maximum 10 Mbps Ethernet Segment Lengths
Unshielded twisted pair
Shielded twisted pair
10BASE-FL multi-mode fiber optic
10BASE-FL single-mode fiber optic
- 100 m (328 ft)
- 150 m (492 ft)
- 2 km (6,562 ft)
- 10 km (32,810 ft)
Maximum Standard Fast Ethernet Segment Lengths:
10BASE-T (CAT 3, 4, 5 UTP)
- 100 m (328 ft)
100BASE-TX (CAT 5 UTP)
Shielded twisted pair
- 100 m (328 ft)
- 150 m (492 ft)
100BASE-FX, half-duplex, multi-mode
100BASE-FX, full-duplex, multi-mode
100BASE-FX, half-duplex, single-mode
100BASE-FX, full-duplex, single-mode
100BASE-FX, full-duplex, Long Reach
- 412 m (1350 ft)
- 2.0 km (6,562 ft)
- 412 m (1350 ft)
- 20.0 km (6K32T ft)
- 40.0 km (122K ft)
www
.
GarrettCom . com
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Maximum Standard Gigabit Ethernet Segment Lengths:
1000BASE-T (CAT5E or higher is recommended)
- 100 m
1000BASE-SX, full-duplex, multi-mode(62.5µm cable) - 220m
1000BASE-SX, full-duplex, multi-mode(50µm cable) - 550m
1000BASE-LX, full-duplex, single-mode(62.5µm cable) -5Km
Fiber connector types supported:
ST-type (twist-lock)
SC-type (snap-in)
MTRJ-type Small Form Factor (SFF)
LC-type Small Form Factor (SFF)
GBIC modules
LEDs: Per Port
LK: Steady ON when media link is operational
ACT: ON with receiver port activity
FDX/HDX: ON = Full-Duplex Mode
OFF = Half-Duplex Mode
100/10: ON = 100Mbps speed
OFF = 10 Mbps
Operating Environment
UL 60950 “Component Parts” temp. ratings: 130° F (55°C) (6K32T)
UL 60950 “Component Parts” temp. ratings: 140° F (60°C) (6K32TRC)
IEC 60068 “Type Test” ratings:- -40°to 185°F (-40°to 85°C)
Ambient Relative Humidity: 5% to 95% (non-condensing)
Altitude: -200 to 13,000 ft. (-60 to 4000m)
Conformal Coating (Humidity Protection) option: Request quote
Packaging
Enclosure: Rugged High strength metal. Suitable for stand-alone
or rack-mounting
Dimensions: 1.70in. H x 17.0in. W x 9.0in. D
4.32cm H x 43.2cm W x 22.9cm D
Cooling method: Fan cooled, @ 3@ 7 cfm ea.
Management Console connector
DB-9 for RS-232 “ null-modem “ cable (sometimes called an X-modem cable)
Power Supply (Internal)
AC Power Connector: IEC-type, male recessed at rear of chassis,
with adjacent manual ON-OFF switch (optional if no Alarms Cont.)
Input Voltage: 100 to 240 VAC (auto-ranging)
Input Frequency: 47 to 63 Hz (auto-ranging)
Power Consumption: 45 watts max (with fiber module)
30 watts for a fully-loaded copper only model
Fuse required for replacement- 1 Amps
DC Power Supply (Options)
-48VDC Power Input Voltage : -36 to -70 VDC
www
.
GarrettCom . com
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Fuse Required – 2Amps
24VDC Power Input Voltage : 20 to 40VDC
Fuse Required – 3Amps
125VDC Power and 100VDC Input Voltage : 88 to 300VDC
Fuse Required – 1Amps
Std. Terminal Block : “ -, GND, + ”
Power Consumption: same as for AC models, see above
Warning- All the fuse replacment must be replaced with same value.
For (Optional) DC internal power supplies at –48VDC, 24VDC and 125VDC,
including Dual Source options (for continuity of operation when either of the DC
input sources are interrupted), see Appendices B and C.
Cooling Method-
6K32T/ 6K32TR(Reverse)- Fan cooled (3 fans inside)
6K32TRC- Convection cooled (No fans) Static Thermal design techniques
Relay Alarm Contact (Optional)
The Alarm Contact option is offered as a configuration option. The alarms can be
initiated through two normally closed Form-C contacts, one loss of power alarm
and one software alarm through user selectable software traps.
Per-port MDI or MDIX on RJ-45
The copper daughter board has MDI-MDIX Auto-crossover on all the RJ-45
ports., and eliminate the use of cross-over cable between the devices. Also
port-specific user settings (such as FDX or HDX, copper 10/100 speed) can
be fixed using software commands.
Agency Approvals
UL listed (UL60950), cUL, CE, Emissions meet FCC Part 15, Class A
NEBS L3 and ETSI Compliant, NEMA TS-2 for traffic control
IEEE 1613 Environmental Standard for Electric Power Substations.
See also Note for Power Substations in Section 3.2.4, 3.6.1, and 5.2.9
IEC61850 EMC and Operating Conditions Class C for Power Substations
Warranty: Three years, return to factory
Made in USA
For a Configuration Guide, see the GarrettCom web site at
(6K32TRC)
www
.
GarrettCom . com
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
1.2
Ordering Information
Magnum Managed Switch
MODEL
DESCRIPTION
Magnum 6K32T 16 10/100 RJ-45 ports managed switch with two optional port modules
(6K32T) which may be configured with a selection of 10/100/1000Mb fiber and copper
connector types, max. 32 ports
Magnum 6K32T-48VDC:Same as 6K32T except power input is –48VDC
Magnum 6K32T-24VDC:Same as 6K32T except power input is 24VDC
Magnum 6K32T-125VDC:Same as 6K32T except power input is 125VDC
Magnum 6K32TRC- Reverse convection cooled(no fans) managed switch, with 16
10/100 RJ-45 ports and two optional port modules which may be configured with a
selection of 10/100/1000Mb fiber and copper connector types,32 ports max.
Magnum 6K32TRC-48VDC:Same as 6K32T except power input is –48VDC
Magnum 6K32TRC-24VDC:Same as 6K32T except power input is 24VDC
Magnum 6K32TRC-125VDC:Same as 6K32T except power input is 125VDC
Configuration Options:
Each Magnum 6K32T & 6K32TRC base unit has two configurable port modules
slot to be configured with any one of the port modules listed below:
Magnum 6K32T & 6K32TRC Port Modules
6KP8-RJ45
6KP4-F10ST
6KP4-FXSC
6KP4-FXST
TP Module, w/eight 10/100Mbps auto-negotiating RJ-45 ports
“2+2” 10Mb Fiber module, w/ four 10Mb 2km FL ST connectors
“2+2” 100Mb Fiber module, w/ four 100Mb 2km FX SC connectors
“2+2” ST Fiber module, w/ s, four 100Mb 2km FX ST connectors
6KP4-FLSTFX “2+2” ST Fiber module, w/ two 100Mb and two 10Mb ports, 2km
6KP6-RJMST “4+2” module, w/four RJ-45 ports and two 2km mm FX SC’s
6KP6-RJMSC “4+2” module, w/four RJ-45 ports and two 2km mm FX ST‘s
6KP6-RJSSC
“4+2” module, w/four RJ-45 ports and two 20km Sgl.m FX SC’s
6KP6-RJSSCL “4+2” module, w/four RJ-45 ports and two 40km Sgl.m FX SC’s
6KP8-MTRJ
6KP8-MLC
6KP8-SLC
SFF Fiber module, w/eight 100Mb mm FX MT-RJ connectors
SFF Fiber module, w/eight 100Mbps mm FX LC connectors
SFF Fiber module, w/eight 100Mbps sgl-m FX LC connectors
“4+4” module, w/four RJ-45 ports and four 2km mm FX MT-RJ’s
6KP8-45MT
6KP8-45MLC “4+4” module, w/four RJ-45 ports and four 2km mm LC connectors
6KP8-45SLC “4+4” module, w/four RJ-45 ports and four 15km Sm LC connectors
6KP6-MT10ST “4+2” module, w/four MTRJ ports and two 10Mb 2km FL ST’s
6KP6-RJ10ST “4+2” module, w/four RJ-45 ports and two 10Mb 2km FL ST ‘s
6KP8-45-2MT “6+2” module, w/six RJ-45 ports and two 2km mm MTRJ connectors
www
.
GarrettCom . com
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
6KP8-45-2SLC “6+2” module, w/six RJ-45 ports and two 100Mb 15km sgl. mode FX
LC connectors
Gigabit Options (Modules using GBIC)
6KP5-G4RJ
“G+4” module, with one GBIC open transceiver and four 10/100 RJ-45
connectors (includes front–panel metal sheet)
6KP3-G2SC
“G+2” module, with one GBIC transceiver and two 100Mb 2km FX SC
fiber ports connectors (includes front–panel metal sheet)
GBPM-2OTX Two port Gigabit module provides two GBIC open transceiver ports for
a user-selectable GBIC transceiver module
GBPM-COTX One slot Gigabit 6K module provides one GBIC open transceiver port
for a user-selectable GBIC transceiver module
GBIC-SXSC
GBIC transceiver module for use in GBPM-xOTX. One 1000BASE-SX
port with multimode SC fiber connector
GBIC-LXSC10 GBIC transceiver module for use in GBPM-xOTX. One 1000BASE-
LX/LH port with 1310nm single mode SC(10km) fiber connector
GBIC-LXSC25 GBIC transceiver module for use in GBPM-xOTX. One 1000BASE-
LX/LH port with 1310nm single mode SC(25km) fiber connector
GBIC-LXSC40 GBIC transceiver module for use in GBPM-xOTX. One 1000BASE-ZX
port with 1550nm, single mode SC(40km) fiber connector
GBIC-LXSC70 GBIC transceiver module for use in GBPM-xOTX. One 1000BASE-ZX
port with 1550nm, single. mode SC(70km) fiber connector.
GBIC-TP
GBIC transceiver module for use in GBPM-xOTX. One 802.3ab
1000BASE-T port with RJ-45 connector
Modules with Gb, not using GBICs
6KP5-1CU4RJ “G+4” module, with one GBIC copper(Auto-negotiating) transceiver
and four 10/100 RJ-45 connectors (includes front–panel metal sheet)
6KP5-1CU4MT “G+4” module, with one GBIC copper(Auto-negotiating) transceiver
and four 100Mb MTRJ Fx-Multi-mode connectors (includes front–panel metal sheet)
6KP3-1CU2FXT “G+2” module, with one GBIC copper(Auto-negotiating) transceiver
and four 100Mb ST Fx-Multi-mode connectors (includes front–panel metal sheet)
6KP2-2GSX two-port in one slot Gigabit 6K module, uses one 6K slot and provides two
Gb Fiber SXSC (1000BASE-SX Multi-mode) ports. (includes front–panel metal sheet).
6KP2-2GCU two-port in one slot Gigabit 6K module, uses one 6K slot and provides two
Gb Copper (1000BASE-RJ45 Auto-negotiating) ports. (includes front–panel metal sheet).
6KM-BLNK
Blank cover for one 6K32T & 6K32TRC module slot opening in a
Magnum 6K32T & 6K32TRC chassis
CONSOLE CBL Industry standard serial cable, DB-9 connectors for RS-232 “ null-
modem “ connection (sometimes called an Xmodem cable), used to connect a PC or a
character terminal to the Management port.
CONSOLE USB Console attachment cable, serial to USB, cable with one DB9 for the
managed Switch and a USB interface for the USB connector to a PC.
MNS-6K License(Management software)- Preloaded with the latest firmware, license
costs included with each 6K base unit.
www
.
GarrettCom . com
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
6K32T/6K32TRC PoE Modules with 48VDC Pass-Through
Configuration options: only one A or B module slot of 6K-Series switch with 48VDC
power input may be configured with a PoE Modules
New P6KP8-RJ45 8 port PoE module for 6ks with 48vdc PS, w/eight PoE power source
10/100 auto-negotiating auto cross RJ-45 ports.
New P6KP8-45RJ “4+4” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and four 10/100 auto-negotiating auto cross RJ-45 ports
New P6KP8-45MT “4+4” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and four 100 Mb 2km mm FX MTRJ connectors
New P6KP8-45MLC “4+4” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and four 100 Mb 2km mm FX LC connectors
New P6KP8-45SLC “4+4” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and four 100 Mb 15km sm FX LC connectors
New P6KP8-45-2MT “6+2” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and two normal RJ-45 10/100 ports +two100 Mb 2km mm FX MTRJ connectors
New P6KP8-452SLC “6+2” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and four 100 Mb 15km Sm FX LC connectors
New P6KP6-RJMST “4+2” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and two 100 Mb 2km mm FX ST connectors
New P6KP6-RJMSC “4+2” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and two 100 Mb 2km mm FX SC connectors
New P6KP6-RJSSC “4+2” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and two 100 Mb 20km sm FX SC connectors
New P6KP6-RJSSCL “4+2” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and two 100 Mb 40km sm FX SC connectors
New P6KP6-RJ10ST “4+2” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and two 10 Mb 2km sm FL ST connectors
6K32T/6K32TRC PoE Modules with 48VDC Power Inside
NOTE: For configuring in 6K Switches having AC /125VDC power input
Configuration options: only one A or B module slot of 6K32-Series switch with
48VDC power input may be configured with a PoE Modules
New 6KAC-PoE-PS Power supply for PoE to 4 ports, 60 watts, mounts inside of a full-
width rack-mount 6K switch with AC power input.
New 6K125VDC-PoE-PS Power supply for PoE to 4 ports, 60 watts, mounts inside of a
full-width rack-mount 6K switch with 125VDC power input.
www
.
GarrettCom . com
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
New PI6KP8-45RJ “4+4” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and four 10/100 auto-negotiating auto cross RJ-45 ports
New PI6KP8-45MT “4+4” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and four 100 Mb 2km mm FX MTRJ connectors
New PI6KP8-45MLC “4+4” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and four 100 Mb 2km mm FX LC connectors
New PI6KP8-45SLC “4+4” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and four 100 Mb 15km sm FX LC connectors
New PI6KP8-45-2MT “6+2” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and two normal RJ-45 10/100 ports +two100 Mb 2km mm FX MTRJ connectors
New PI6KP8-452SLC “6+2” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and four 100 Mb 15km Sm FX LC connectors
New PI6KP6-RJMST “4+2” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and two 100 Mb 2km mm FX ST connectors
New PI6KP6-RJMSC “4+2” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and two 100 Mb 2km mm FX SC connectors
New PI6KP6-RJSSC “4+2” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and two 100 Mb 20km sm FX SC connectors
New PI6KP6-RJSSCL “4+2” port PoE module for 6ks with 48vdc PS, w/four PoE power
source and two 100 Mb 40km sm FX SC connectors
New PI6KP6-RJ10ST “4+2” port PoE module for 6ks with 48vdc PS, w/four POE power
source and two 10 Mb 2km sm FL ST connectors
GarrettCom, Inc. reserves the right to change specifications, performance
characteristics and/or model offerings without notice.
www
.
GarrettCom . com
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
2.0
2.1
Introduction
Inspecting the Package and Product
Examine the shipping container for obvious damage prior to installing this
product; notify the carrier of any damage that you believe occurred during shipment or
delivery. Inspect the contents of this package for any signs of damage and ensure that
the items listed below are included.
This package should contain:
1
Magnum 6K32T, 6K32TR or 6K32TRC Managed Switch, base unit
(configured with user-selected port module option in modular slot)
1
1
1
1
AC Power Cord (U.S. and other 115 VAC only)
Set of metal “Ears” for 19” rack mounting
Installation and User Guide (this manual)
Product Registration Card
Remove the items from the shipping container. Be sure to keep the shipping
container should you need to re-ship the unit at a later date. To validate the product
warranty, please complete and return the enclosed Product Registration Card to
GarrettCom, Inc. as soon as possible.
In the event there are items missing or damaged, contact the party from whom
you purchased the product. If the unit needs to be returned, please use the original
shipping container if possible. Refer to Section 6, Troubleshooting, for specific return
procedures.
www
.
GarrettCom . com
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
2.2
Product Description - Magnum 6K32TRC Managed Switch
The IEC61850 complied and attributed with “green” environmentally
friendly, Magnum 6K32TRC Managed Switch is specially designed with a convection
cooled thermal design techniques to minimize heat generation to provide an efficient,
highly reliable and secured Ethernet solution for heavy duty Industry, Power sub-
stations and temp-uncontrolled outdoor applications. Specially designed and enclosed
in a “Reverse” aluminum case, the 6K32TRC proudly offered with modularity, port
density (up to 32 ports max.) and security in a 1U rack-mount package.
Being a sibling of the successful 6K managed switch family, the Magnum
6K32TRC supports modularity in the last two slots to configure with any of the various
Figure 2.2.1a: A typical 6K32TRC front view, 16 RJ-45 ports (Fixed) +2 Modular
slot with 8 Port fiber on C and Dual Giga module on D slot.
6KP modules offered. The Magnum 6K32TRC provides effective and economical
Ethernet solutions with 16 10/100 RJ-45 ports fixed and two modular configuration slots.
The two modular configurable slots of the Magnum 6K32T offer the flexibility to
configure up to sixteen 100Mb, (RJ-45 and 16 fiber ports) or a maximum of four
Gigabit(1000Mb) options to handle high bandwidth application efficiently. The two
modular slots are boosted with 10Mb/10/100Mb/ 100Mb/1000Mb and can be configure
with any of modules offered with copper or Fiber media or combo. The various PoE
modules option is an additional advantage for Magnum 6K32TRC users to provide a
secure and economical solution to critical remote applications.
The preloaded robust and intuitive MNS-6K Managed Network firmware with
multiple secured managed features is able to handle industry-standard IEEE 802.1p QOS
prioritization and non-blocking wire speed on all ports. It provides high performance
switching services for both “smooth” streaming and “bursty” data traffic. For redundant
www
.
GarrettCom . com
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
LANs, it offers S-ring, RS-Ring, Link-Loss-Learn, STP and RSTP. Security features
include SNMPv3, SSL/SSH, 802.1X, TACACS+, Port Security, and Tagged VLANs
and a secured user friendly web based option. The IGMP feature for multicast traffic
and streaming video application and IGMP-L2 mode feature is an attempt to provide a
Layer 3 solution with 6K-Switches effectively and economically.
See MNS-6K materials for further details about Management software.
df (web)
(CLI)
The Magnum 6K32TRC‘s port flexibility can be achieved via a family of 6K
port modules (6KPM). These modules come with copper and fiber-built-in (emphasizing
Small Form Factor fiber for high fiber port density), 6-port modules for fiber and RJ-45
combinations, and 1Gb or (1+1) Dual Gb port module selections using GBIC transceivers
in copper or fiber. These modules can be factory configured in a base chassis unit (or
may be changed in the field by trained technicians) to adapt the unit as per the user’s
application and Ethernet media requirements. Evolving mixed-media requirements for
10Mb and 100Mb fiber, copper, and 1000Mb Gigabit ports can be easily handled by the
Magnum 6K32TRC product reliably
The packaging and wide selection of AC and DC power-input options with (-
48VDC, 24VDC, 125/110 VDC, target the Magnum 6K32TRC for heavy-duty
applications. The chassis rack mounting style as “Reverse” (with the ports and LEDs
and the power-input and the management console connector all in the rear and a
duplicate set of LEDs in the front). Rack widths accommodated include standard 19”
RETMA, ETSI, and 23” Telco. Input power may be AC, or –48VDC for Telco
environments, or 24VDC for Industrial and 125VDC for power sub stations applications.
Designed for primarily use in power sub- stations, un-controlled temperature
and Industrial applications, the Magnum 6K32TRC provides high performance plug-and-
play hardware operation, 802.1p packet prioritization in hardware, and industry-standard
www
.
GarrettCom . com
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
managed networks software functionality with plenty of secure and remote monitoring
features, all in convenient 1U rack-mount packages.
2.2.1a Magnum 6K32T Managed Switch Chassis
The high port density and fan cooled Magnum 6K32T was designed for heavy
duty Carrier class and Industrial applications that require high port density and secure
devices which save in cost, rack space and running cool to provide reliable solutions.
This rack mountable managed switch comes with a wide variety of AC/DC options to
deliver an effective and efficient solutions for the required application needs.
The 6K32T Switches have 16port fixed RJ-45(10/100Mb) ports and
2 modular slots available to configure with numerous 6KPM options. The options can be
RJ-45 or fiber media, 10 or 100 or 1000Mb copper or Fiber, or Small Form Factor
options to provide more fiber ports. The two modular slots can be configure with
maximum of four Gigabit modules as shown in Fig. 2.2.1.b..
Figure 2.2.1b: 6K32T front view, configured for16 RJ-45 ports +2 Modular slot
with Dual Giga module.
The modular option with two slots explores this managed switch’s extra
capability to meet any 10 or 100 or Gigabit requirement effectively satisfying any
demand for complex Ethernet. The Triple Play demand of bandwidth to meet “voice-
data-video” over Ethernet will be handled efficiently by this managed switch and will
play an effective role in providing modularity to the solution.
The growing demand of security and “Ease of use” are the other adding
features of this managed switch. The switch allows the users to secure their network
through port security, Radius X, Tacacs+ and Snmpv3 and provide an effective solution
of ease of use through “Secure Web based management and scripts feature to manage the
6K32T switch remotely”. The 6K32T loaded with robust MNS-6K firmware is specially
designed to meet the future demand of Ethernet requirement with cost-effective secure
solutions. The Magnum 6K32T is also available in a Reverse model option, where the
LEDs are on the front and the available ports along with the power supply area found on
the rear side. This configuration is mostly used for carrier-class market.
The modules which may be configured and used in the modular slots of the
Magnum 6K32T are described here.
www
.
GarrettCom . com
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
The Magnum 6K32T is preloaded with robust and intuitive MNS-6K Managed
Network Software to handle industry-standard IEEE 802.1p QOS prioritization and non-
blocking wire speed on all ports. It provides high performance switching services for
both “smooth” streaming and “bursty” data traffic. For redundant LANs, it offers S-ring,
RS-Ring, Link-Loss-Learn, STP and RSTP. Security features include SNMPv3,
SSL/SSH, 802.1X, TACACS+, Port Security, and Tagged VLANs. See MNS-6K
materials for further details about software.
The Magnum 6K32T’s port flexibility is achieved via a family of 6K port
modules (6KPM). These modules come with copper and fiber-built-in (emphasizing
Small Form Factor fiber for high fiber port density), 6-port modules for fiber and RJ-45
combinations, and 1Gb or 2Gb port module selections using GBIC transceivers in copper
or fiber. These modules can be factory configured in a base chassis unit (or may be
changed in the field by trained technicians) to adapt the unit to the user’s application and
Ethernet media requirements. Evolving mixed-media requirements for 10Mb and 100Mb
fiber, copper, and Gigabit ports can be easily handled by the Magnum 6K32T &
6K32TRC product reliably
The packaging and power-input options target the Magnum 6K32T &
6K32TRC for heavy-duty applications. The chassis mounting rack style may be
“regular” (with the ports and LEDs in the front and the power input and management
console connector in the rear) or “Reverse” (with the ports and LEDs and the power-
input and the management console connector all in the rear and a duplicate set of LEDs
in the front). Rack widths accommodated include standard 19” RETMA, ETSI, and 23”
Telco. Input power may be AC, or –48VDC for Telco environments, or 24VDC for
Industrial applications.
2.2.2 Eight-port SFF fiber modules (6K8-MTRJ, 6K8-MLC), 100Mb fiber
1
3
5
7
1
3
4
5
6
7
ACT
ACT
ACT
AC
F/H
ACT
F/H
ACT
F/H
ACT
F/H
AC
F/H
F/H
LK
LK
LK
LK
F/H
F/H LK
LK
LK
LK
LK
L
2
8
ACT
ACT
ACT
AC
F/H
ACT
F/H
F/H
ACT
F/H
AC
ACT
F/H
F/H
LK
LK
LK
LK
F/H
LK
L
F/H
2
4
6
8
2
4
6
8
Fig.2.2.2 : SFF Fiber Port Modules, 6K8-MTRJ (to the left) and
6K8-MLC or -SLC (below)
www
.
GarrettCom . com
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
In an eight-port SFF fiber port module, all of the fiber ports are of the same
speed (100Mb), mode, and connector type. Models that are available with Small Form
Factor (SFF) are multi-mode MT-RJ or LC-type connectors, and single-mode LC-type
connectors.
The 100Mb fiber eight-port modules for the Magnum 6K32T & 6K32TRC
normally are set (factory default) to operate in full-duplex mode for best fiber distance
and performance. Using the 6K32T & 6K32TRC’s MNS software, the user may select
full- or half-duplex mode per-port through the set-up of the software (See the Magnum
6K32T & 6K32TRC MNS Software Manual for the flexibility to adapt to any FDX or
HDX type of Fast Ethernet devices).
There are three LED’s per fiber port. The Link (LK) LED indicates “ready for
operation” on that port when lit, the F/H LED indicates operation in full-duplex mode
when ON (half-duplex when OFF), and the blinking ACT LED indicates receiving
Activity on the port. A fiber cable must be connected into a SFF port and the Link (LK)
indicator for that port must be ON (indicating there is a powered-up device at the other
end of the cable) in order for a LK LED to provide valid indications of operating
conditions on that port.
1
3
5
7
2.2.3 Eight-Port Copper
Module, 6K8-RJ45 (MDIX)
LK
10/100
The 6K-Series’s 8-port Copper
port module, model 6K8-RJ45,
provides eight 10/100Mb switched
RJ-45 ports. The 10/100Mb
ACT
F/ H
2
4
6
8
10/100
LK
F/H
ACT
switched ports normally (as a
default setting) are independently N-way auto-negotiating, and auto-crossover(MDIX)
for operation at 10 or 100Mb speed in full- or half-duplex mode, i.e., each independently
selects a mode and speed to match the device at the other end of the twisted pair cable.
(See Section 4.3 for auto-negotiation and MDIX details). The auto-crossover feature will
automatically determine the other side of connection to make the connection, and
eliminate the need of cross-over cable.
www
.
GarrettCom . com
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
On the model 6K8-RJ45 module, there are four LEDs for each port, two in the
connector and two separate. The LK (Link) LED indicates “ready for operation” on that
port when lit. The blinking ACT (Activity) LED indicates receiving Activity on that port
when lit. The 10/100 LED indicates operation at 100Mb speed when ON and at 10 Mb
speed when OFF (when auto-
1
3
5
7
negotiation is not disabled).
The FDX/HDX LED is ON to
indicate full-duplex operation
and OFF to indicate half-
LK
10/100
ACT
F/ H
2
4
6
8
10/100
LK
duplex mode. A twisted pair
cable must be connected into
F/H
ACT
an RJ-45 port and the Link (LK) indicator for that port must be ON (indicating there is a
powered-up device at the other end of the cable) in order for a LK LED to provide valid
indications of operating conditions on that port.
Using the 6K8-Series (MNS-6K) management software, the user may disable
auto-negotiation and fix the desired operation of each RJ-45 port. User may select 10Mb
or 100Mb speed and full- or half-duplex mode per-port as per user requirement. (See
Magnum MNS-6K Software Manual for details info.).
2.2.3a New PoE(Power Inside), model PI6KP8-45RJ (MDIX), 8-port 10/100Mb
The New PoE RJ-45
PI6KP8V-45RJ
ports act similar to
regular RJ-45 ports,
8 Port@ 10/100Mb POE Copper ports
2
except they have
1
3
5
LK/ACT
PO
10/10
0
1
capability of providing
power on each port to
power up the PD
F/
2
4
6
E
H
8
10/10
LK/ACT
0
F/H
PO
E
4
3
devices, per the
LK/ACT
PoE
10/100
FULL/HALF
1
3
2
4
IEEE802.3af PoE
standard. Only 4 x RJ-
45 (10/100) ports
maxm. support POE(Power Inside) option in one rack mounted 6K-unit. The power
inside PoE option is factory configured and equipped with the necesasary power option
to support four 802.3af PoE pd devices. The 4-RJ45 POE module are also available with
mix –n-match with fiber modules. Please check the ordering information Sec.1.2. for all
the various PI6K PoE modules option.
The LEDs on 6KP8-RJ45- PoE module are slightly different compared to
regular (non-PoE) RJ-45 modules as shown in Fig 2. When the PoE port is in use, the
www
.
GarrettCom . com
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
PoE LED is ON when connected properly to a 803.af compliant PD device on that port.
When non-PoE devices are connected, the PoE LED is OFF. Operation of Ethernet data
traffic is not affected by PoE.
LINK and ACTIVITY LEDS are combined on the PoE modules into one LED
that is marked as LINK/ACT, as shown in the diagram.
2.2.3b New PoE(Power Pass-through), model P6KP8-RJ45 (MDIX), 10/100Mb 8-
port
The PoE (Power-pass-through) RJ-45 ports act similar to regular RJ-45 ports,
except they have capability of providing power on each port to power up the PD devices,
per the IEEE802.3af PoE standard. The Power Pass-through PoE modules are totally
dependent upon the powerful -48VDC input power supply to support more RJ-45
(10/100) ports. Each port requires atleast 15watts to power up the PoE PD devices.
Maxm. one PoE modules can be configured in the A, B or C slot of any 6K s with -
48vdc power input. The PoE modules are also available with mix –n-match with fiber
modules. Please check the ordering information Sec.1.2 for all the various P6K PoE
modules option.
The LEDs
on 6KP8-RJ45- PoE
module are slightly
different compared
to regular (non-PoE)
RJ-45 modules as
shown in Fig 2.
When the PoE port
is in use, the PoE
LED is ON when
connected properly to a 803.af compliant PD device on that port. When non-PoE devices
are connected, the PoE LED is OFF. Operation of Ethernet data traffic is not affected by
PoE.
LINK and ACTIVITY LEDS are combined on the PoE modules into one LED
that is marked as LINK/ACT, as shown in the diagram.
2.2.4
Six-Port “4 + 2”Combo Modules, 4@ 10/100 RJ-45 and 2@100Mb
fiber
1
3
5
7
1
3
5
7
LK
10/100
LK
10/100
ACT
ACT
F/H
F/H
ACT
F/H
ACT
ACT
F/H
ACT
F/H
6
F/H
6
TX
LK RX
TX
LK RX
2
TX LK RX
2
TX LK RX
4@RJ-45 + 2@ 100Mb ST or SC
The combo six-port modules are combinations of copper and fiber media, available as
four 10/100 switched RJ-45 copper ports and two 100Mb switched multi-mode fiber ST,
www
.
GarrettCom . com
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
SC or single mode SC or Long Reach SC ports. For ports numbering, ports 1,3,5,7 are
copper, ports 2 and 6 are fiber, ports 4 and 8 are not present.
The four RJ-45 ports operate just like the 8-port copper module with auto-cross
(MDIX) feature to eliminate the use of cross-over cable, and the two fiber ports operate
at 100Mbps full-duplex (default). User mode control per port through the MNS software
is also the same.
On Magnum “4+2” Combo modules, there are four LED’s for each RJ-45 port,
which indicate status the same as described for the 6K8-RJ45 in Section 2.2.3 above. The
fiber port’s LEDs indicate status the same way as described for the SFF fiber modules in
Section 2.2.2 above. Color-coding on the panel of the module shows which LEDs
belong to which port.
The Magnum Combo six-port modules are also available with 4@ MTRJ
100Mb mm SFF fiber and 2@10Mb fiber mm ST ports, and with 4@ RJ45 10/100
copper and 2@10Mb fiber mm ST
1
3
5
7
ports. The
LK
10/100
4@ RJ-45 + 2@ 10 Mb ST
ACT
F/H
ACT
F/H
ACT
operation of the SFF fiber
F/H
6
and the RJ-45 half of the module is
as described for those port types
TX
LK RX
2
TX LKRX
above. For detailed information about 10Mb mm ST fiber half of the module, see
Section 2.2.5.
2.2.5
Four-Port 10 Mb mm Fiber ST Modules
ACT
F/H
ACT
F/H
TX LK RX
TX LK RX
TX LK RX
1
ACT
F/H
2
5
ACT
F/H
6
T
LK
R
The 4port @10Mb ST fiber modules behave the same as the 8@100Mb ST
fiber modules except for the 10Mb speed. For port numbering, ports 1, 2, 5, 6 are present,
ports 3, 4. 7, 8 are not present. The default setup on the 10Mb fiber module is half-
duplex, which allows the Magnum 6K32T & 6K32TRC Switch to connect to any 10Mb
hub or media converter or almost any other device with a 10Mb fiber Ethernet port. User
mode control per port through the MNS software is the same as the other 6K32T &
www
.
GarrettCom . com
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
6K32TRC modules. The fiber ports support fiber cabling distances according to the
10BASE-FL standard, i.e., 2km distance for multi-mode fiber. (Single-mode for up to
10Km distance may be available as a special order configuration).
2.2.6
Gigabit (1000Mbps) port modules
The Magnum 6K32T & 6K32TRC & 6K32’s offer wide options for Gigabit
speed with multiple choices for the modular slot. The new Magnum 6K32T & 6K32TRC
can be configured with four Gigabit ports (copper or Fiber) maximum. The Gigabit port
option for the modular slot comes in a couple of different configurations. The two
Gigabit port modules have been offered as GBPM-2OTX (fiber or RJ-45), whereas the
single Gigabit module comes in flavors of G+4(10/100 RJ-45 ports) or G+2 (100Mb fiber
ports) as shown below in the figure.
ACT
ACT
F/
F/
TX AC RX
1
3
5
7
TX LK RX
L
10/100
F/
ACT
F/
ACT
F/
ACT
TX LK RX
TX
L
RX
1@ 1000Mb Fiber SC + 2@ 100Mb SC
1@ 1000Mb Fiber SC + 4@10/ 100Mb
The 6K32T & 6K32TRC modules provide a GBIC opening for insertion of industry-
standard GBICs to provide Gigabit (Gb) media flexibility. GBIC models are available for
both multi-mode (550m) and single-mode (10, 25, 40, 70)km fiber options, and for
Gigabit copper as well with new models appearing often.
The 1000Mb Gigabit fiber-port modules on the Magnum 6K32T & 6K32TRC
are normally set (factory default) to operate at AUTO mode for best fiber distance and
performance. The 1000Mbps SC fiber-optic module on the Gigabit -SX and Gigabit-LX
transceivers are compatible with the IEEE 802.3z Gigabit standards.
There are two LEDs mounted on each Gigabit port module. The Gigabit fiber
port is by default configured to AUTO mode, and can be fixed at 1000Mbps speed full-
duplex mode at any time. The Gigabit fiber port has LEDs that indicate LK (Link status)
and ACT (receiving activity) on that port when lit.
For Dual Gigabit modules option, please check page#60 for details info.
www
.
GarrettCom . com
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
2.2.7
Packet Prioritization, 802.1p QOS
Quality of Service means providing consistent predictable data delivery to
users from datagram paths that go all across a network. As a LAN device, the Magnum
6K32T & 6K32TRC can do its part to prevent any QOS degradation while it is handling
Ethernet traffic through its ports and buffers.
The Magnum 6K32T & 6K32TRC switching hardware supports the IEEE
802.1p standard and fulfills its role in support of QOS, giving packet processing priority
to priority tagged packets according to the 802.1p standard. In addition to hardware
support for QOS, the MNS software (R3) supports two priority queues that can be shared
across the eight levels of defined packet priorities for application-specific priority control
by the user through software configuration settings.
2.2.8
Frame Buffering and Flow Control
Magnum 6K32T & 6K32TRC’s are store-and-forward switches. Each frame
(or packet) is loaded into the Switch’s memory and inspected before forwarding can
occur. This technique ensures that all forwarded frames are of a valid length and have
the correct CRC, i.e., are good packets. This eliminates the propagation of bad packets,
enabling all of the available bandwidth to be used for valid information.
While other switching technologies (such as "cut-through" or
"express") impose minimal frame latency, they will also permit bad frames to propagate
out to the Ethernet segments connected. The "cut-through" technique permits collision
fragment frames (which are a result of late collisions) to be forwarded which add to the
network traffic. Since there is no way to filter frames with a bad CRC (the entire frame
must be present in order for CRC to be calculated), the result of indiscriminate cut-
through forwarding is greater traffic congestion, especially at peak activity. Since
collisions and bad packets are more likely when traffic is heavy, the result of store-and-
forward operation is that more bandwidth is available for good packets when the traffic
load is greatest.
When the Magnum 6K32T & 6K32TRC Switch detects that its free buffer
queue space is low, the Switch sends industry standard (full-duplex only) PAUSE
packets out to the devices sending packets to cause “flow control”. This tells the sending
devices to temporarily stop sending traffic, which allows a traffic catch-up to occur
without dropping packets. Then, normal packet buffering and processing resumes.
www
.
GarrettCom . com
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Another feature implemented in Magnum 6K32T & 6K32TRC Switches is a
collision-based flow-control mechanism (when operating half-duplex only). When the
Switch detects that its free buffer queue space is low, the Switch prevents more frames
from entering by forcing a collision signal on all receiving half-duplex ports to stop
incoming traffic.
2.2.9
Managed Network Software (MNS-6K) for Magnum 6K32T &
6K32TRC
Magnum 6K32T & 6K32TRC come with licensed MNS-6K Firmware (Rel
3.2), which allows the configuration of the Magnum 6Ks as a Managed Switch and other
Software enabled features. For additional information about MNS-6K, see the Magnum
6K-Series MNS Software User guide in pdf format, a separate document normally
accessed via your web-browser, at ftp://ftp.garrettcom.com/
or FTP client program by ftp.GarrettCom.com using
user : m6kuser
password : m6kuser
All MNS-6K software information, including new releases and upgrades related to MNS-
6K software, can be accessed and download from GarrettCom’s FTP site.
Alternatively, for documentation and latest information on GarrettCom proprietary
MIBs for SNMP visit
www.GarrettCom.com/techsupport/index.htm#software and look for Magnum
MNS-6K info..
Magnum MNS-6K Operator Training – This interactive training software
gives the basic and advanced information about the Magnum MNS-6K management
software and is a useful tool for a first time user.
For upgrading the Magnum 6K32T & 6K32TRC Switch to its latest
Magnum 6K-Firmware, follow the steps and instruction provided on -
www
.
GarrettCom . com
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
2.3
Features and Benefits
„ Managed switching for high performance Ethernet LANs
Magnum 6K32T & 6K32TRC & 6K32TRC Switches provide non-blocking (all ports
can run at full speed at once) performance with standard Managed Networks Software
(MNS-6K) included. They are typically used in LAN traffic centers with 24
10/100Mb ports or one or two Gigabit ports for backbone connections where managed
network services are desired.
„ Switching services includes 802.1p QoS packet prioritization
The Magnum 6K32T & 6K32TRC switching hardware supports QoS, giving packet
processing priority to priority tagged packets according to the IEEE 802.1p standard.
For port- and application-specific priorities, the QoS software may be configured by
the user.
„ Features Fiber-Built-In
Magnum 6K32T & 6K32TRC Managed Switches are designed with modular slots to
naturally include fiber ports and support mixes of the following; multi-mode and
single-mode; 10 Mb, 100Mb and 1000Mb speed; full-and half-duplex; and classic
Small Form Factor (SFF) and GBIC fiber connectors. RJ-45 10/100 ports can also be
configured in the mix of port types.
„ Modular design for port flexibility, in a 1U space-saving rack-mount package
The 1U Magnum 6K32T & 6K32TRC chassis has 1 slot for port configurations. A
family of 2, 4, 6 or 8 port modules allows the user to select the desired mix of port
types and speeds. There are over 20 different modules in the family to choose from.
The port modules are normally factory installed and tested, but may be changed in the
field.
„ Rack-mounting may be standard or “reverse”, 19 inch or ETSI or 23” Telco
The standard rack mounting provides Ethernet ports and status LEDs in front, service
connections (power input and management console) in the rear. “Reverse” rack
mounting provides status LEDs in front and all cabling connections in the rear.
Standard 19’ rack mount brackets are included, with ETSI and 23” Telco optional.
„ Standard AC power input, -48VDC or 24VDC or 125VDC input is optional
Standard AC power input has an IEC plug and is auto-ranging for worldwide use. For
special applications, models with –48VDC or 24VDC or 125VDC are available. Dual
Source DC input can also be selected and configured on the DC power input models.
„ Heavy-duty design for Telco (NEBS tested) and other industrial environments
Fiber ports take more power than copper ports, but the Magnum 6K32T & 6K32TRC
design provides for this with heavy-duty components. The ambient temperature can
be up to 55°C.
www
.
GarrettCom . com
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
„ MNS-6K licensed Network Management Software included, S-Ring/RS-Ring
optional
Release 3.5 (summer ’06) includes SNMP, Secure Web Management, RMON, CLI,
Port Security; Port Mirroring; Port Settings Control; Telnet, TFTP, FTP support,
Spanning Tree Protocol, RSTP, LLL, S-Ring Redundancy Mgr, (optional) multi-level
QoS, Port and Tag-based VLANs, GVRP, IGMP Snooping, SNMPc GUI support;
BootP and DHCP client for IP configuring, Radius X, TACACS+ etc.
„ MDI-MDIX Auto-negotiating on RJ-45 ports for convenient cascading using
straight RJ-45 cable.
„ Support PoE module to provide power via RJ-45 cable on the modular slot.
2.4
Applications
Magnum 6K32T & 6K32TRC Fiber Switches offer high performance along
with one or two modular slot options to fulfill the choice of copper/Fiber, 10,100 or
1000Mb requirements. The 6K32T & 6K32TRC also offers MNS-6K management
software loaded with multiple useful features. The Magnum IEC61850 6K32T &
6K32TRC Switches are used in a variety of Power sub-stations applications including,
Industrials and temp. un-controlled, secure VLAN- performance upgrades to
departmental networks, and LAN traffic centers that require Gigabit backbone services.
The performance characteristic of the 6K32T & 6K32TRC Switches enables them to
inter-connect a series of subnets (one subnet per 6K32T Switch port) in a LAN traffic
center. The subnet connections may be via fiber or twisted pair cabling, 100Mbps or 10
Mbps speed, and full-or half-duplex mode.
The mixed-media capability in the modular slot is ideal for upgrading existing
Ethernet LAN networks where existing cabling must be accommodated. The fiber-built-
in media capability provides future-proof fiber cabling for the LAN structure. The
secured management features offer a multiple options to provide a secure Network
solution.
Example 1 : Magnum 6K32T Switch for a VLAN application
Equipped with lots of advanced management features, the Magnum 6K32T
Managed switch is able to handle a VLAN application and provide security and
performance in an Ethernet network center. A secure VLAN-enabled network is simply
an administratively-configured broadcast domain. The network administrator determines
which ports and nodes are in which broadcast domains by setting membership profiles
www
.
GarrettCom . com
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
for each of them. The Magnum 6K32T’s VLAN capability can be configured in two
types of virtual LANs; Port-based VLANs and Tag-based VLANs.
In an office environment where departments such as Finance, Engineering,
R&D, and Marketing need to each keep a secure LAN, the 6K32T’s VLAN feature will
prevent traffic cross-over among traffic domains and thus keep sensitive data and
information controlled. The Managed Magnum 6K32T equipped with VLAN capability
is ideal for any application where a secure VLAN to multiple departments is needed.
The modularity of the 6K32T Managed Switch makes it an attractive choice for
use in applications with LAN connections to an organization’s multiple site offices. The
different offices can be easily connected together with the Fiber ports supported by the
Magnum 6K32T Switch. A main NT-server in a secure area protected from earthquake or
fire hazards can be connected to one or two full duplex Gigabit Fiber ports.
Full-duplex future proof fiber media can easily connect long distance subnets
and provide a stable secure network to all applications. The SNMP management
capability of the Magnum 6K32T Switch helps create a database of all the network
subnets to easily manage the network. Secure web-based management is also included,
with authentication and encryption to keep out even determined trouble-makers.
Example 2. In another Telecommunications storage data application, a secure managed
switch is required to provide an Ethernet backbone for a diversified network with
multiple subnets. The backbone consists of high speed LAN segments supported by
1000Mbps full-duplex future-proof fiber media to provide secure long distance LAN
connections. The entire network is sharing a higher bandwidth Gigabit-enabled data-
mining server for the vital database located in a separate secured building. The copper
ports are required for multiple subnets inside the building. The entire spread network is
managed to provide easy, detectable, uninterrupted support through a viewable SNMP
monitor.
Magnum 6K32PW
1
3
5
1
3
5
10/10
F/
LK
10/10
F/
LK
10/10
F/
LK
1000Mb Data Mining Servers
Managed Fiber
Switch
AC
6
H
AC
6
LK
AC
6
H
H
2
4
2
4
2
4
Magnum 800E
WorkgroupPHW
100
GARRETT
1
2
5
6
10/10
10/10
LK
u
R
bCO4L
LINK
RX
8
LINK
RX
10/10
LK
F/H
F/H
ACT
ACT
F/H
ACT
Data
Data
Internet
Magnum DS8016 StackaXble Hub
1
2
3
4
5
6
7
8
9
1
0
1
1
PWRBR
Router
12
13
14
1
5
1
6
LK/RX
PORT
2
1
3
4
5
6
7
8
9
10 11 113 14 5
COL 10
COL 100
10
UPLINK
Magnum 800E
Workgroup Hub
1
2
5
8
6
4
PWR COL
LINK
RX
LINK
RX
100
GARRETT
Magnum 800E
1
2
5
8
6
WorkgroupPWHubCO4L
R
Data
100Mb Servers
and Workstations
LINK
LINK
RX
100Mbps Fll
100
RX
GARRETT
Data
for
Magnum 800E
Workgroup Hub
1
2
5
6
4
8
PWR COL
LINK
RX
LINK
RX
100
GARRETT
S8016 StackaXble Hub
1
2
3
4
5
6
7
8
9
1
0
1
1
12
13
14
1
5
1
6
another Bldg.
3
4
5
6
7
8
9
10 11 13 15
UPLINK
Data
Magnum 800E
1
2
5
8
6
WorkgroupPWHu
R
bCO4L
LINK
RX
LINK
RX
100
GARRETT
Data
Magnum DS8016 StackaXble Hub
1
2
3
4
5
6
7
8
9
1
0
1
1
PWRBR
12
13
14
1
5
1
6
LK/RX
COL 10 PORT
2
3
4
5
6
7
8
9
10 11 3 15
1
10
COL 100
UPLINK
Data
Data
100Mb Servers
and Workstations
Data
100Mb Servers
and Workstations
Magnum DS8016 StackaXble Hub
1
2
3
4
5
6
7
8
9
1
0
1
1
PWRBR
COL 10 PORT
12
13
14
1
5
1
6
LK/RX
2
3
4
5
6
7
8
9
10 114 1
1
COL 1
UPLINK
Magnum DS8016 Stackable Hub
X
1
2
3
4
5
6
7
8
9
PWRBR
COL 10 PORT
12
13
14
1
5
1
6
LK/RX
2
3
4
5
6
7
8
9
10 11 12 13 14 5
1
10
COL 100
UPLINK
Data
Data
Magnum 800E
WorkgroupPWHu
100
GARRETT
1
2
5
8
6
R
bCO4L
LINK
RX
LINK
RX
100Mb Servers
and Workstations
10Mb Workgroup
www
.
GarrettCom . com
Data
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
The Magnum 6K32T Managed Switch equipped with copper and optional dual Gigabit
fiber ports on modular slots provide an economical and seamless solution to the
requirements. The user-configurable Magnum 6K32T provides an extra boost to the
network requirements by providing copper/fiber media along with the higher bandwidth
support of 10/100 and 1000Mb. The user can utilize the SNMP feature equipped with
VLAN, Port security, 802.1X, and other security features to provide a secure and stable
network as per the requirement
The 6K32T Managed Switch with NEBS Level 3 compliance and management
flexibility allows the user more than one configuration alternative. The user has an
advantage by fulfilling the present requirements as well as benefiting from the multiple
choices of modules to support future expansion as the network evolves. The dual Gigabit
port option in the modular slot boosts the bandwidth for high speed to support the peak
traffic and minimize congestion.
Example 3 Redundant Application (6K32TRC)
In a redundant application for high network availability where a rack-
mountable managed switch with over 24 ports is required with dense port features,
Magnum 6K32T’s equipped with redundant LAN features like S-Ring, RSTP, Link-
Loss-Learn and various security features are easily qualified for the application. The -
48VDC input power option with Dual Source is especially useful in telecom central
offices.
The Magnum 6K32T with two Gigabit ports in the modular slot allows it to
connect into a Gigabit mesh structure with an RSTP and S-Ring combination used in a
no-single-point-of-failure self-healing LAN topology along with a ring of multiple 6K25s
at the edge to allow the system to efficiently recover from a fault in the network. The
industry standard Rapid Spanning Tree Protocol 802.1d is used in the top eight switches
(see diagram below) to perform GB mesh fault recovery, whereas the bottom ring setup
has been configured with S-Ring and Link-Loss-Learn for faster recovery in a big ring.
A redundant LAN setup not only provides a reliable recovery solution from
network faults, but also improves operating up-time to simplify maintenance, save
money and recover valuable time. In a critical application where secure data has been
stored in a data mining storage facility, a redundant network provides a more secure
solution.
The figure below has Magnum 6K32T’s and 6K25’s connected over the gigabit mesh
structure for a high bandwidth secure redundant LAN setup.
www
.
GarrettCom . com
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
1
1
5
F
/
H
H
10
/
1
0
0
L
K
/
A
C
T
F
/
2
4
6
8
1
0
1
2
1
4
16
1
15
F
/
H
1
0
/
1
0
0
L
K
/
A
C
T
F
/
H
2
4
6
8
10
1
2
14
1
6
1
1
5
F
F
/
H
1
0
/1
0
0
L
/
A
C
T
/
H
2
4
6
8
1
0
1
2
1
4
16
1
15
1
1
5
F
/
H
F
F
/
/
H
H
1
0
/
1
0
0
L
K
/
A
C
T
1
0
/1
0
0
L
K
A
C
T
F
/
H
2
4
6
8
10
1
2
14
1
6
2
4
6
8
1
0
1
2
1
4
1
6
1
1
5
F
F
/
/
H
H
1
0
/1
0
0
L
K
/
C
T
2
4
6
8
1
0
1
2
1
4
16
1
1
5
F
/
H
H
1
0/
1
0
0
L
K
/
A
C
T
F
/
2
4
6
8
1
0
1
2
1
4
16
1
15
1
15
F
/
/
H
H
F
/
H
H
1
0
/
1
0
0
L
K
/
A
C
T
1
0
/
1
0
0
L
K
/
A
C
T
F
F
/
2
4
6
8
10
1
2
14
1
6
2
4
6
8
10
12
14
16
1
15
L
F
/
H
H
1
0
/
1
0
0
K
/
A
C
T
1
15
F
/
/
H
H
1
0
/
1
0
0
L
K
/
A
C
T
F
/
2
4
6
8
10
12
14
16
F
2
4
6
8
10
1
2
14
1
6
1
15
L
F
/
/
H
H
1
0
/
1
0
0
K
/
A
C
T
F
1
15
2
4
6
8
10
1
2
14
1
6
F
/
H
H
1
0
/
1
0
0
L
K
/
A
C
T
1
15
F
/
2
4
6
8
10
12
14
16
F
/
/
H
H
1
0
/
1
0
0
L
K
/
A
C
T
F
2
4
6
8
10
1
2
14
1
6
6K32TRC in a Redundant application
Example 4: In a “ (video+data)” application where a network being designed to catered
the need of multicast streaming and broadcast traffic of higher bandwidth to provide a
video conferencing and video in demand channel option to the user.
The Magnum 6K32TRC with two slots filled with Gigaport
module and a robust management firmware with MNS-6K qualify this requirement
efficiently. The New IGMP L2-Mode feature on Magnum 6K32TRC and loaded with
management capability and secure web feature fulill this requirement effectively.
The Dual Giga option on each of the two slot add 4 Gigaport to
handle the bandwidth requirement and 16 10/100 RJ-45 ports to feed the other needs of
equipment connected to the 6K32TRC. The robust Tag based vlan feature will able to
segregates different ports belong to one group and provide an effective solution for
bandwidth. The SNMP option and secure web based will allow the remote capability and
monitoring the network securely. The versatile mechanical design with rack mounting
capability and AC/DC option will be an additional feature to take care of temperature
and power option issue.
www
.
GarrettCom . com
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Equipped with IGMP-L2 mode enhanced features allow the Magnum
6K32TRC to meet the fastest growing application of video monitoring or video
surveillance demand of industry and provide an economical and effective solution to
meet that expectation.
1
0
/
0
0
1
5
F
/
H
1
0
/
0
0
F
/
H
2
4
6
8
1
0
1
2
1
4
1
6
10
10
/
1
0
0
L
K
A/
C
T
1
0
/1
0
0
L
K
/
A
C
T
1
0
/
1
0
0
L
K
/
A
C
T
1
0
/1
0
0
L
K
/
A
C
T
15
15
15
15
1
1
1
1
F
0
/
H
F
/
H
F
0
/
H
F
/
H
/
1
0
L
K
A/
C
T
1
0
/1
0
0
L
K
/
A
C
T
1
0
/
1
0
L
K
/
A
C
T
1
0
/1
0
0
L
K
/
A
C
T
F
/
H
F
/
H
F
/
H
F
/
H
2
4
6
8
10
1
2
1
4
16
2
4
6
8
10
1
2
1
4
16
2
4
6
8
1
0
1
2
1
4
16
2
4
6
8
10
1
2
1
4
16
1
0
/1
0
0
L
K
/
A
C
T
15
1
1
0
/1
0
0
L
K
/
A
C
T
F
/
H
1
0
/1
0
0
L
K
/
A
C
T
1
15
F
/
H
1
0
/1
0
0
L
K
/
A
C
T
F
/
H
2
4
6
8
10
1
2
1
4
16
F
/
H
2
4
6
8
10
1
2
1
4
16
1
0
/1
0
0
L
K
/
A
C
T
1
0
/1
0
0
1
15
L
K
/
A
C
T
F
/
H
15
1
0
/1
0
0
L
K
/
A
C
T
1
F
/
H
H
1
0
/1
0
0
L
K
/
A
C
T
F
/
H
2
4
6
8
10
1
2
1
4
16
F
/
2
4
6
8
10
1
2
1
4
16
1
0
/1
0
0
L
K
/
A
C
T
1
15
F
/
H
1
0
/1
0
0
L
K
/
A
C
T
1
0
/1
0
0
L
K
/
A
C
T
15
1
F
/
H
F
/
H
2
4
6
8
10
1
2
1
4
16
1
0
/1
0
0
L
K
/
A
C
T
F
/
H
2
4
6
8
10
1
2
1
4
16
10
/
1
0
0
L
K
A/
C
T
1
15
F
0
/
H
1
0
/
1
0
0
L
/
C
T
10
/
1
0
L
K
A/
C
T
1
15
F
0
/
H
F
/
H
1
0
/
1
0
L
/
C
T
2
4
6
8
10
1
2
1
4
16
F
/
H
2
4
6
8
10
1
2
1
4
16
6K32TRC with IGMP-L2 mode
Figure 4: A multicast traffic through a 6K32TRC Switches using IGMP-L2
mode feature with Gigabit redundancy
www
.
GarrettCom . com
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
3.0
Installation
Before installing the equipment, it is necessary to take the
following precautions:
1.) If the equipment is mounted in an enclosed or multiple rack
assembly, the environmental temperature around the equipment
must be less than or equal to 55C FOR 6K32T and 60C for 6K32TRC.
2.) If the equipment is mounted in an enclosed or multiple rack
assembly, adequate airflow must be maintained for proper and
safe operation.
3.) If the equipment is mounted in an enclosed or multiple rack
system, placement of the equipment must not load unevenly or
overload the rack system.
4.) If the equipment is mounted in an enclosed or multiple rack
assembly, verify the equipment’s power requirements to prevent
overloading of the building/s electrical circuits.
5.) If the equipment is mounted in an enclosed or multiple rack
assembly verify that the equipment has a reliable and
uncompromised earthing path.
6.) 24vdc, -48vdc, and 125vdc must be installed in restricted
access locations.
7.) CB-Circuit breaker of 10Amps should shown on top of Rack.
This section describes installation of the Magnum 6K32T Switches, as well as
connection of the various Ethernet media types.
3.1
Locating Magnum 6K32T Switches
The location of a Magnum 6K32T Switch is dependent on the physical layout
of the network. Typically the Switch is placed in a central wiring location where groups
of network devices need to be connected in order to communicate with each other. These
Switches are typically rack mounted in a wiring closet see Section 3.3.2 below), but
because they have rubber feet they can also be installed on a shelf or table top unit. The
compact size allows it to be easily placed in an office or lab area, and it can also be either
shelf of wall-mounted (see Section 3.3.1 below).
Locate an AC receptacle that is within six feet
(2 meters) of the intended Magnum 6K32T site. The
rugged metal case of the Magnum 6K32T will normally
protect it from accidental damage in a lab or workplace
setting. Maintain an open view of the front to visually
monitor the status LEDs. Keep an open area around the
unit so that cooling can occur from the small fan on the
left side while the unit is in operation. See figure below.
Figure 3.1: Location of the Magnum
6K32T’s cooling fans
www
.
GarrettCom . com
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
3.2
Connecting Ethernet Media
The Magnum 6K32T & 6K32TRC Switches are specifically
designed to support all standard Ethernet media types within a single Switch
unit. This is accomplished by using a family of different port Modules which
can be individually selected and configured per-port. See Section 2.4 for a
description of the PMs.
The various media types supported along with the corresponding IEEE
802.3 and 802.3u standards and connector types are as follows:
IEEE Standard
Media Type
Max. Distance
Port Module
Fiber:
1000BASE-FX
100BASE-FX
m
m1 Fiber
sgl.m2 Fiber
m1 Fiber
sgl.m2 Fiber
m1 Fiber
220m ( ft) GBIC-SXSC
70km GBIC-LXSC
2.0km (6,562 ft) 6K6-MSC, -MST
18.0km (95K ft) SSC, SSCL
m
small form factor
m
2.0km (6,562 ft) 6K8-MTRJ, -MLC
small form factor sgl.m1 Fiber
Copper:
10BASE-T, 100BASE-TX twisted pair 100m (328 ft)
15 km
6KP8- SLC
6K8-RJ45
1000BASE-TX twisted pair
100m (328 ft)
1 mm = multi-mode
GBIC-TP
2 sgl.m = single-mode
3.2.1
Connecting Fiber Optic ST-type, “twist-lock”
The following procedure applies to installations using a PM with ST-type fiber
connectors. This procedure applies to ports using a 6K32T & 6K32TRC module,
MST-type port.
1. Before connecting the fiber optic cable, remove the protective dust caps from the
tips of the connectors on the PM. Save these dust caps for future use.
2. Wipe clean the ends of the dual connectors with a soft cloth or lint-free lens tissue
dampened in alcohol. Make certain the connectors are clean before connecting.
Note:
One strand of the duplex fiber optic cable is coded using color
bands at regular intervals; you must use the color-coded strand on the
associated ports at each end of the fiber optic segment.
3. Connect the Transmit (TX) port (light colored post) on the Magnum PM to the
Receive (RX) port of the remote device. Begin with the color-coded strand of
the cable for this first TX-to-RX connection.
4. Connect the Receive (RX) port (dark colored post on the PM) to the Transmit
(TX) port of the remote device. Use the non-color coded fiber strand for this.
5. The LINK LED on the front of the PM will illuminate when a proper connection
has been established at both ends (and when power is ON in the unit). If LINK is
not lit after the cable is connected, the normal cause is improper cable polarity.
Swap the fiber cables at the PM connector to try to remedy this situation.
www
.
GarrettCom . com
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
3.2.2
Connecting Fiber Optic SC-type, "Snap-In"
The following procedure applies to installations using a PM with SC-type fiber
connectors, i.e., using 6K-MSC or 6K-SSC (single mode) etc.
When connecting fiber media to SC connectors, simply snap the two square male
connectors into the SC female jacks of the 6KPM until they click and are secure.
3.2.3
Connecting Single-Mode Fiber Optic
When using single-mode fiber cable, be sure to use single-mode fiber port
connectors. Single-mode fiber cable has a smaller diameter than multi-mode fiber cable
(9/125 microns for single-mode, 50/125 or 62.5/125 microns for multi-mode where xx/xx
are the diameters of the core and the core plus the cladding respectively). Single-mode
fiber allows full bandwidth at longer distances, and may be used to connect 10 Mb nodes
up to 10 Km apart, or 18Km with the 6K-SSC.
The same procedure for multi-mode fiber applies to single-mode fiber
connectors. Follow the steps listed in Section 3.2.2 above.
3.2.4
Connecting Twisted Pair (RJ-45,CAT3, CAT5, Unshielded or Shielded)
The RJ-45 ports of the Magnum 6K32T & 6K32TRC can be connected to the
following two media types: 100BASE-TX and 10BASE-T. CAT 5 cables should be used
when making 100BASE-TX connections. When the ports are used as 10BASE-T ports,
CAT 3 may be used. In either case, the maximum distance for unshielded twisted pair
cabling is 100 meters (328 ft).
Media
IEEE Standard
10BASE-T
Connector
RJ-45
Twisted Pair (CAT 3, 4, 5)
Twisted Pair (CAT 5)
100BASE-TX
RJ-45
NOTE : It is recommended that high quality CAT. 5 cables (which work for both 10 Mb
and 100Mb) be used whenever possible in order to provide flexibility in a
mixed-speed network, since dual-speed ports are auto-sensing for either 10 and
100Mb/s.
The following procedure describes how to connect a 10BASE-T or 100BASE-
TX twisted pair segment to the RJ-45 port. The procedure is the same for both
unshielded and shielded twisted pair cables.
1. Using standard twisted pair media, insert either end of the cable with an RJ-45
plug into the RJ-45 connector of the port. Note that, even though the connector is
shielded, either unshielded or shielded cables and wiring may be used.
2. Connect the other end of the cable to the corresponding device
3. Use the LINK LED to ensure proper connectivity by noting that the LED
will be illuminated when the unit is powered and proper connection is
established
www
.
GarrettCom . com
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
NOTE: for Power Substations: In support of the IEEE 1613 Class 2 standard, GCI
advises that, for substation applications, the RJ-45 ports are intended for
connectivity to other communication equipment such as routers or
telecommunication multiplexers installed in close proximity (i.e., less than 2
meters or 6.5ft) to the 6K32. It is not recommended to use these ports in
substation applications to interface to field devices across distances which
could produce kigh (greater than 2500V ) levels of ground potential rise (GPR)
during line-to-ground fault conditions. The 6K32 passes the 1613specifications
for zero packet loss with fiber ports & with RJ45 ports used as indicated here.
3.2.5
Connecting Twisted Pair (CAT-5e or better, Unshielded or Shielded)
The RJ-45 1000BASE-TX Gigabit ports of the Magnum 6K32T & 6K32TRC
can be connected via copper media with the following minimum specifications;
1000BASE-T, CAT-5e, or for better results, 100-ohm UTP shielded twisted pair (STP)
balanced cable. The CAT-5e or the more effective 100-ohm UTP shielded twisted pair
(STP) balanced cable is recommended when making 1000BASE-TX connections. In
either case, the maximum distance for unshielded twisted pair cabling is 100 meters (328
ft).
Media
IEEE Standard
Connector
Twisted Pair (CAT-5e)
1000BASE-T
RJ-45
NOTE : It is recommended that high quality CAT-5e cables (which work for both 100
Mb and 1000Mb) be used whenever possible in order to provide flexibility in a
mixed-speed network.
The following procedure describes how to connect a 1000BASE-T twisted pair segment
to the RJ-45 port. The procedure is the same for both unshielded and shielded twisted
pair cables.
1. 1000BASE-T connections require that all four pairs or wires be connected. Insert
either end of the cable with an RJ-45 plug into the RJ-45 connector of the port.
Note that, even though the connector is shielded, either unshielded or shielded
cables and wiring may be used.
2. Connect the other end of the cable to the corresponding device
3. Use the LINK LED to ensure proper connectivity by noting that the LED will be
illuminated when the unit is powered and proper connection is established
3.2.6
Gigabit SFP (Small Form-factor Pluggable) Optical Transceivers
The small form-factor pluggable (SFP) is a compact optical transceiver used in optical
communications for both telecommunication and data communications applications. Due
www
.
GarrettCom . com
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
to its compact, hot pluggable characteristics, SFPs are becoming a very popular choice
for various applications. The small-chassis Magnum 6K is designed for industry-standard
Gb-SFPs and Gb-SFPCU (copper) for user selection of the SFP gigabit media type as
desired.
All SFPs used in Magnum 6Ks are compliant with the industry standard Multi-Source
Agreement (MSA) ensuring compatibility with a wide range of networking kit.
TX
RX
Bail clasp
Side View
---Duplex LC connector --
Front view
Note: It is highly recommended to remove the fiber cable first before removing the SFP
transceiver for any reason. Not removing the fiber cable first can damage the fiber cable,
cable connector or optical interfaces. It is advised not to remove and insert a SFP
transceiver frequently as this may shorten its useful life.
Note: Always use an ESD wrist strap while handling the SFP transceivers since the
SFP modules are static sensitive devices.
Note: The copper 1000BASE-T SFP transceiver port supports 1000Mb only. It is
recommended to use a straight-through RJ-45(4-twisted pair) connection while
connecting to any Server/workstation. While connecting with any Switch/repeater or
other device, it is recommended to use Crossover RJ-45 (4-twisted pair) category 5 or
higher cabling. The maximum length supported on copper 1000BASE-T is 100mts (328
ft.).
www
.
GarrettCom . com
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
The various SFPs transceivers supported by GarrettCom 6KQs D slot are-
Module Model#
Gb Modules, fixed ports--SFP (Small Form Factor)
6KP2-2GSFP 2 SFP
Gigabit
6KP2-1GSFP1CU 1SFP
1 CU
6KP1-1SFP
6KP1-1GCU
1SFP
1 CU
Gb SFP fiber optic transceivers
Gb SX, 850nm wavelength, 500 m distance
SFP-SX
SFP-LX10
SFP-LX25
Gb LX, 1310nm wavelength, 10km dist
Gb LX, 1310nm wavelength, 25km
distance
SFP-ZX40
SFP-ZX70
Gb ZX, 1550nm wavelength, 40km
distance
Gb ZX, 1550nm wavelength, 70km
distance
3.2.7
Power Budget Calculations for Magnum 6K32T & 6K32TRC PM’s with
Fiber Media
Receiver Sensitivity and Transmitter Power are the parameters necessary to
compute the power budget. To calculate the power budget of different fiber media
installations using Magnum products, the following equations should be used:
OPB (Optical Power Budget) = PT(min) - PR(min)
where PT = Transmitter Output Power, and PR = Receiver Sensitivity
Worst case OPB = OPB - 1dB(for LED aging) - 1dB(for insertion loss)
Worst case distance = {Worst case OPB, in dB} / [Cable Loss, in dB/Km]
where the “Cable Loss” for 62.5/125 and 50/125µm (M.m) is 2.8 dB/km,
www
.
GarrettCom . com
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
and the “Cable Loss” for 100/140 (Multi-mode) is 3.3 dB/km,
and the “Cable Loss” for 9/125 (Single-mode) is 0.5 dB/km
and the “Cable Loss” for 9/125 (Single-mode) is 0.4 dB/km (LXSC25)
and the “Cable Loss” for 9/125 (Single-mode) is 0.25 dB/km(LXSC40)
and the “Cable Loss” for 9/125 (Single-mode) is 0.2 dB/km (LXSC70)
The following data has been collected from component manufacturer’s (Agilent’s and
Lucent’) web sites and catalogs to provide guidance to network designers and installers.
Fiber
Port
Module
Speed,
Std. Wave Cable X’mitr R’cvr Worst Worst* typical typical*
km Size Output Sens. OPB, distance OPB, distance
PT , dB PR ,dB dB Km, fdx dB Km, fdx
-
Mode
Std.
fdx length
(hdx) nm
µm
62.5/125 -15.0 -31
14
-31 19.5
50/125 -19.5 -31 19.5
17
23.5
13.5
14
10Mb Multi-
2
5
6
7
6KP4-
F10ST
850
Mode
(2)
100/140 -9.5
FL
5.9
3.4
3.0
2.0
4.8
5
6KPM-
62.5/125 -20
-31
9.0
5.5
100Mb Multi-
2
(0.4)
1300
FX
mode
50/125 -23.5 -31
12
MST, MSC
4
100Mb Single- 18+
1300 9/125
1300 9/125
-15
-5
-31
-34
14
29
17.5
32.5
6KPM-SSC
28
58
35
65
(0.4)
FX
mode
100Mb Single- 40
6KPM-
SSCL
(0.4)
FX
mode
62.5/125 -20
-31
9.0
5.5
15.8
12.2
100Mb Multi-
2
(0.4)
3.0
2.0
5.5
4.0
6KPM-
MTRJ
1300
FX
mode
50/125 -23.5 -31
2
(0.4)
100Mb Multi-
6KPM-
MLC
1300 62.5/125 -19
-31
12
16
4
5.7
FX
mode
15+
(0.4)
100Mb Single-
1310 9/125
-15
-28
-17
11
-
6KPM-SLC
22
2
-
Mode
FX
0.55
10
1000Mb Multi-
mode
GBIC-
SXSC
850 62.5/125 -9.5
50/125
5.5
12.5
4
1000Mb Single-
mode
GBIC-
LXSC10
1300 9/125
1550 9/125
1550 9/125
1550 9/125
-9.5
-4.0
-4.0
-3.0
-20
-21
-21
-23
8.5
15
15
18
10.5
17.5
17.5
20.5
17
37.5
60
21
43
25
1000Mb Single-
mode
GBIC-
LXSC25
40
1000Mb Single-
mode
GBIC-
ZXSC40
70
70
1000Mb Single-
mode
GBIC-
ZXSC70
102
90
* Note: The use of either multi-mode or single-mode fiber to operate at 100Mbps speed
over long distances (i.e., in excess of approx. 400 meters) can be achieved only
if the following factors are both applied:
www
.
GarrettCom . com
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
•
The 100Mb fiber segment must operate in full-duplex (FDX) mode, i.e. the
full-duplex (factory default) setting for 100Mbps fiber ports must be used,
and
•
The worst-case OPB of the fiber link must be greater than the fiber cable’s
passive Attenuation.
(Attenuation = Cable loss + LED aging loss + Insertion loss + safety factor)
3.3
Table-Top or Shelf Mounting
The Magnum 6K32T & 6K32TRC Managed Switches can be easily mounted
on a table-top or any suitable horizontal surface. They have four rubber feet to provide
stability without scratching finished surfaces.
3.3.1
Rack-mounting (for 19” RETMA racks), Magnum 6K32T &
6K32TRC’s
Installation of a Magnum 6K32T & 6K32TRC Fiber Switch in a 19” rack is a
simple procedure. The units are 1U (1.70”) high. When properly installed, the front-
mounted LED status indicators should be in plain view and easy to read.
Rack-mount installation requires
special 19” rack-mounted
brackets and screws (included
PW
1
3
5
Magnum
M
5
1
3
5
M
10/10
LK
10/10
LK
10/10
LK
Managed
Switch
AC
F/
10/10
AC
6
AC
F/
10/10
F/
10/10
2
4
2
4
6
LK
LK
with each Magnum 6K32T &
6K32TRC unit). These brackets
attach to the front sides of the
G
F/H
F/H
AC
AC
F/H
AC
PW
1
3
5
Magnum
Managed
Switch
1
3
5
10/10
LK
10/10
LK
10/10
LK
AC
F/
10/10
AC
6
AC
F/
10/10
F/
10/10
2
4
2
4
6
2
4
6
LK
LK
LK
Fig 3.3.1 Dual Side-Mountings for
Magnum 6K32T & 6K32TRC
units
F/H
F/H
AC
AC
F/H
AC
PW
1
3
5
MMagnum
M
Managed
1
3
5
1
5
10/10
LK
AC
10/10
LK
AC
LK
10/10
LK
AC
LK
Switch
Standard Flush
F/
10/100
F/
10/10
F/
10/10
2
4
6
2
4
6
2
4
6
LK
G
F/H
F/H
AC
AC
F/H
AC
23” Mount Bracket
Mid-Range Mount or
5” Set-Back Bracket
PW
1
3
5
MMagnum
M
Managed
1
10/10
LK
AC
10/10
LK
AC
LK
10/10
LK
AC
LK
Switch
F/
10/10
F/
10/100
F/
10/10
2
4
6
2
4
6
2
4
6
LK
GA
F/H
F/H
AC
AC
F/H
AC
PW
1
5
Magnum
Managed
1
3
5
10/10
LK
10/10
LK
AC
LK
10/10
LK
AC
LK
Switch
F/
10/10
AC
6
F/
10/10
F/
10/10
2
4
2
4
6
2
4
6
LK
F/H
F/H
AC
AC
F/H
AC
Switch (regular package, not the
Reverse version), which is then
typically fastened into a standard
19” RETMA rack as shown here
The 23” brackets and the ETSI
(European metric, approx. 21”) brackets are also available (optional) for rack-mounting
www . GarrettCom . com
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
the Magnum 6K32T & 6K32TRC Switches. These brackets are popular in the Telco
industry where they are a standard for Central Office rack-mounting purposes. The 23”
and the ETSI brackets are mainly used for larger equipment
These brackets are rack-mounted in a frame typically accessed in operation from both
sides.
The bracket mounting holes in the sides of the Magnum 6K32T & 6K32TRC
permits it to be mounted in various ways. The same holes fit all three types (19”, ETSI,
and 23”) of brackets. The mounting for the 23” is illustrated in Figure 3.3.1 below. The
brackets may be attached flush with the front, or attached in the center for a set-back
mounting which may reduce cabling torque.
The optional 23” brackets and the ETSI (21”) brackets each come as a pair in a
package, along with the necessary screws for attaching the brackets to the sides of the
Magnum Switch unit. They must be ordered as separate line items.
3.3.2 Rack-mounting, Reverse version of the Magnum 6K32T’s
(Not available as of October 2005) The optional Reverse Magnum 6K32T
Model has all of the cabling (Ethernet cabling, power cabling and console port cabling)
connectors in the rear, and the status LEDs in the front. The status LEDs that are co-
incident with the ports are still present there, and a second or dual set of LEDs are used
for status visibility in the front of the unit, showing the same data.
D
D
C
C
B
B
A
Standard Flush
Mount Bracket
Mid-Range Mount
or
D
D
C
C
B
B
A
A
Rear Mount
D
D
C
C
B
B
A
A
Fig 3.3.2 Reverse Magnum 6K32TRC units, rack-mounted in a frame
www
.
GarrettCom . com
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
There are three options of brackets available to mount in the standard 19”
frame, 23” frame, or ETSI (21”) frame. The 19” brackets are included with each unit, the
other two may be purchased as separate options.
With each bracket type, there are three different mounting options as shown in Fig. 3.3.2.
The case of the Magnum 6K32T has mounting holes prepared for each of the mounting
arrangements. Users may choose the mounting arrangement most suitable for their
installation.
3.4
Powering the Magnum 6K32T & 6K32TRC Managed Switch
The Magnum 6K32T & 6K32TRC Switches incorporate an internal universal
power supply and have a recessed male IEC connector for the AC power cord at the left-
rear. A manual power ON-OFF switch is adjacent. A six-foot 115 VAC 60 Hz standard
power cord is supplied with each unit shipped within the United States and Canada.
The auto-ranging power supply supports installation environments where the
AC voltage is from 90 to 260 volts with a power input frequency between 47 and 63 Hz.
The 32-port units will consume over 30 watts of power typically. When connecting the
Ethernet cabling, there is no need to power down the unit. Individual segments can be
connected or disconnected without concern for AC power-related problems or damage to
the unit.
Power supply options are available to suit the 6K32T & 6K32TRC Switches to
special high-availability communications and/or heavy industrial-grade applications,
including:
*
*
-48VDC, 24VDC and 125VDC with single DC input,
-48VDC, 24VDC and 125VDC with dual-source DC input,
See the Appendices of this manual for more details. Use an RFQ for other variations.
3.4.1 Alarm Contacts for monitoring internal power, and Software Traps
The Alarm Contacts feature, optional on Magnum 6K32T & 6K32TRC’s,
provides two Form C Normally Closed (NC) contacts to which the user can attach two
sets of status monitoring wires at the green terminal block. When this option is present,
the terminal block for Alarm Contacts is part of the Power Input panel in the Magnum
6K32T & 6K32TRC case. The AC or DC power input connection is in the same panel. A
manual On-Off Switch for power to the unit is not available on 6K32T & 6K32TRC units
with the Alarm Contacts option, as these two features occupy the same space in the case.
The first NC Alarm Contact (top position) is a “Software Alarm”, operated
by user settings in the MNS-6K software. The user can disable the Software Alarm
feature with a software configuration command if desired. When the Software Alarm is
enabled, the Form C Normally Closed (NC) contact is held close during normal software
operation. A user-defined software malfunction, such as an SNMP Trap or a Software
www
.
GarrettCom . com
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Security violation or an S-Ring Fault, causes the contact to open and thus trigger an
alarm in the user’s monitoring system
The second (bottom position) NC Alarm Contact is held close when there is
power on the main board inside of the 6K32T & 6K32TRC. This provides a “Hardware
Alarm” because the NC contacts will open when internal power is lost, either from an
external power down condition or by the failure of the power supply inside of the
Magnum 6K32T & 6K32TRC Switch. Useful info. about Alarm contacts:
1. There is four terminal block (1,2,3,4)provided next to AC/DC power supply
2. The top two pins (1,2) are software operated
3. The bottom two pins (3,4) are hardware operated
4. By default it is NC (normally closed)
5. The software operation needs to be enabled and set to get the Alarm traps. For detailed
information about the Software Alarm and software control of SNMP alarm traps, please
reference the Magnum MNS-6K Software User Manual. (Chapter 19th).
3.5
6K32T & 6K32TRC Port Module (6KPM) Installation
The Magnum 6K32T & 6K32TRC Switches are normally received from the
factory with 24 ports fixed and one required 6KPM module installed. There may be
situations where 6KPM cards need to be added or replaced. In cases where a 6KPM
module needs to be added in the modular slot, the faceplate for an available front-
mounted slot must be removed. The following procedure describes this operation.
3.5.1 Preparation for Installing and Removing 6KPMs
STOP!!!
Be sure the power cord and connections
for all powers single or dual, is unplugged
from the chassis before attempting to remove
and/or replace any PM cards.
Failure to do so may result in damage to the unit
and will void the warranty.
Caution- Avoid Static Discharge: Opening of the 6K32TRC chassis can only be
performed by trained service persons. The port modules (like most
electronic equipment) are sensitive to static discharge. Use proper ESD
measures when handling port modules.
Step 1. Make sure the 6KPM Card package has all necessary accessories to install it
properly. Each 6KPM Card package for field installation contains
(Daughterboard (Bigger) and Granddaughter board (smaller), three 5/8 stand
offs for the Granddaughter board, six #4-40 Pan-Head screws along with a
www
.
GarrettCom . com
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Front panel face plate package. The Front panel faceplate package includes 3
retainer brackets and six #2-56 flat head screws.
NOTE: Every 6KPM Card package comes with their matching Daughter and
Granddaughter board. The copper 6KPM card should not work properly if
mixed with other Fiber combo 6KPM card packages. Always install the PM
module separately one by one to avoid the mixing.
NOTE for Power Substations: In support of the IEEE 1613 Class 2 standard, GCI
advises that, for substation applications, the serial RJ-45console ports are
intended for temporary connectivity to other equipment such as PCs. Since the
console port connection is temporary, it is excluded from IEEE 1613 packet-
loss testing per the 1613 standard-defined test procedure.
Step 2. Remove Chassis Cover
The Magnum 6K32T & 6K32TRC chassis are combined with top, bottom and
front panel parts and assembled together with the help of 17 Philips-head
screws. There are 5 screws located on the front-bottom and 3 at rear-top of the
unit and one each on the front and rear sides. First Remove the front panel
screws (total 12) as shown in the fig 3.5.1a. Once these are removed, the front
panel can be easily pulled out to the front. The top cover can be easily pulled
off to the front from the chassis base, as shown in the Fig. 3.4.1b. When the
chassis top cover has been removed, the interior of the unit is exposed.
Figure 3.5.1a: Removing front panel after the screws being removed
www
.
GarrettCom . com
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Fig 3.5.1b: Pulling out the top coved from the chassis base
Caution: Be careful not to disturb the power supply.
Looking down into the Magnum 6K32T & 6K32TRC unit, notice that there are
individual PM installation spaces and female latch (white) connectors provided on the far
right side of main board along with four stand-off’s for 6KPM card position. (See Figure
3.5.1c).
Figure 3.5.1c: Magnum 6K32T & 6K32TRC modular slot side (front-right side),
without chassis cover
Step 3. Remove front panel
face plate retaining screws
There are one PM slot located
on the front-right side of the
chassis cover. Looking into the
vertical placed Chassis cover
of the unit, there are one
bracket with retaining screws
(#256 flat head ) which hold
www
.
GarrettCom . com
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
the PM Face plate card slot securely. These six screws shown in the picture below are
used to secure a PM face plate in position, but unscrew only four of the screws as shown
in Fig. below. These screws are also used to secure the individual 6KPM cards screen
plate which can be subjected to significant forces from the attached cables. (See Figure
3.5.1d)
Figure 3.5.1d: Top View – 6KPM retaining screws hold Face Plate
3.5.2
Installing 6KPM Cards in the Magnum 6K32T & 6K32TRC
Up to four front-mounted 6KPM cards may be installed in one Magnum
6K32T & 6K32TRC Managed Switch unit. Follow these steps to install a
6KPM.
Step 1. Remove top chassis cover. See procedure in Section 3.5.1 above.
Step 2. Placed Granddaughter board (as shown in fig. 3.5.2a and 3.5.2b) on the chassis
built in stand off (female) provided at the front of the 6K32T & 6K32TRC Main Board
and screw down tightly with the three 5/16 stand-off (male) on the top of the
Granddaughter board The 5/16 stand off has been used to place the daughter board on the
top of the granddaughter board and latch it securely.
Fig 3.5.2b Granddaughter Board placed in modular slot and secured with three 7/16
stand-off’s as shown with arrow mark
www
.
GarrettCom . com
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Step 3. The figure here illustrates the basic layout of an individual PM card. 6KPM
card fits into the space provided on the main board over the grand-daughter Bd. and the
male latched cream color connector( as shown in above fig. with arrow mark).
Fig 3.5.2d: Daughter Board shown upside down with two male latch connectors
Step 4. Hold the daughter
board with both
hands at the end
and align the two
cream color
latching connectors
(male) placed at the
bottom of the
daughter board with
Fig 3.5.2e Daughter Bd. Being placed over the Grand daughter Bd. and the mating
connector being matched to lockup properly
the other female connector placed on the Granddaughter and main board. As shown
above in Fig. 3.5.2e
Step 5. Once the latching connectors are aligned properly and the mounting holes are
aligned with stand offs then press slowly and firmly with two fingers (as shown
below in Fig. 3.5.2f) on the top of the latching connectors until the connectors
latched
www
.
GarrettCom . com
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Fig.3.5.2f: Securely
latching up 6KPM
Cards into a
Magnum 6K32T &
6K32TRC & 6K32
NOTE:. When leaving
6KPM slots empty, always
use a face plate (Magnum
6K8-BLNK) to cover the slot opening in the front panel. This will maintain proper
cooling air flow, safety, and operation as required by FCC, CE, and other regulations.
Step 6. Now screw down the daughter board with 7 #440 screws except the last two at
the end, so that it holds the daughter board securely. The figure below shows the
top view of 6KPM card after successfully installing the 6KPM cards inside the
Magnum 6K32T &
6K32TRC.
Fig. 3.5.2g Top View :
6KPM Module installed
inside a 6K32T &
6K32TRC Switch
Step 7. Once the installation of granddaughter and daughter modules is done properly,
the front panel screen plates(come along with the 6K-module) need to be properly placed
on the front of the chassis cover to complete the installation process.
www
.
GarrettCom . com
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Step 8. Once the 6KPM cards have been installed, the chassis top cover should be
replaced by matching at the two front corners properly and slide in until it
reaches the rear end and fit properly to match the holes. Make sure the chassis
cover is aligned properly before securing the enclosure. Place the front panel
part at the end by sliding in to the front side and secure it with 12 screws as
being mentioned earlier.
3.5.3
Removing 6KPM Cards
To properly remove a 6KPM card from the 6K32T & 6K32TRC Managed
Switch, follow the 3 steps below.
Step 1. Remove chassis cover
See procedures in Section 3.5.1 above.
Caution: Be sure the power cord is unplugged.
Step 2. Remove retaining screws placed on top for the 6KPM and Face Plate
On the top of the daughter module there are six
retaining screws for each 6KPM card. These
screws are used to secure a 6KPM card in
position (see Figure 3.5.3a). Remove the three
standoffs holding the Granddaughter board with
the chassis. The screen faceplate screws out from
the inside front of the chassis cover by loosening
the 4 screws and bracket while holding it down
firmly.
Figure 3.5.3a: Top View
- 6 retaining screws shown by arrows
Step 3. Remove 6KPM Card
Carefully and
gently pull out the
daughter board
from the latching
connectors, using
both hands,
gripping the board
near the latch-up
www
.
GarrettCom . com
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
connectors as shown in Fig. 3.5.3b . If the now empty slot is to remain unused, be sure
to install a 6KPM-BLNK face plate cover.
Figure 3.5.3b: Removing a 6KPM Card
Follow the step 8 to complete the process successfully.
NOTE:1. If the modular slot has not being used and moved to other unit, the empty
slot must be covered with Blank cover, to maintain proper air-inflow inside the unit
and keep off from dust and other unavoidable substance, otherwise can cause a failure
in the Switch.
2. If the PM module in the modular slot is not being installed properly or loose in
connection, the MNS-6K management software will not boot-up properly and a error
will generate as –{ failed to read register device type (offset 0x1600) on slot “A or B or
C or D”}, whichever the slot has been used.
3. Always boot-up the Switch after any new module installation on modular slot to
confirm the successful installation, before placing the chassis cover.
3.6
Connecting the Console Terminal to Magnum 6K32T & 6K32TRC
(Management)
Use a DB-9 “null modem” cable to connect the Magnum 6K32T & 6K32TRC
Console Port (the RS-232 port on the 6K32T & 6K32TRC Switch) to the your
PC, so that your PC becomes the 6K32T & 6K32TRC’s Console Terminal.
Note: The DB-9 cable does not include with the 6K32T & 6K32TRC
unit package.
Console (DB-9)
Por
t
CONSOLE
PORT
OF
Rear View of Magnum 6K32T
Note: For detail description of Managed Network Software (MNS-6K) and Magnum
6K32T & 6K32TRC Switch configuration for Network Management, please refer to
Magnum 6K32T & 6K32TRC Software Manual available on GarrettCom‘s FTP site.
Detail info. about the MNS is available on 2.2.9 ( see page no. 13) of this manual.
www
.
GarrettCom . com
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
3.6.1
RS-232 (DB-9) Console Com port (Serial port) pin assignments.
Pin 1
Pin 5
DB-9 (Console port connector)
Pin
Signal
Description
1
CD
Carrier detect (not used)
Receive Data (input)
Transmit Data (output)
not used
2
RXD
TXD
open
GND
open
3
4
5
Signal Ground
6-9
not used
The above provided information enables a managed station( a PC or Console terminal) to
connect directly to the switch using a straight through cable.
Note: For using Console port to configure the managed switch, a serial (Null-modem)
female to female cable is required to communicate properly. The Null-Modem (DB-9)
cable is optional and can be order from the factory, along with the unit as-
CONSOLE CBL for serial port
CONSOLE USB for USB port
NOTE for Power Substations: In support of the IEEE 1613 Class 2 standard, GCI
advises that, for substation applications, the serial RJ-45console ports are
intended for temporary connectivity to other equipment such as PCs. Since the
console port connection is temporary, it is excluded from IEEE 1613 packet-
loss testing per the 1613 standard-defined test procedure.
www
.
GarrettCom . com
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
4.0
OPERATION
This chapter describes the functions and operation of the Magnum 6K32T &
6K32TRC Switch.
4.1
Switching Functionality
A Magnum 6K32T & 6K32TRC provides switched connectivity at Ethernet
wire-speed among all of its ports. The Magnum 6K32T & 6K32TRC support 10/100Mbs
for copper media and 10 or 100Mb separate traffic domains for fiber ports to maximize
bandwidth utilization and network performance. All ports can communicate to all other
ports in a Magnum 6K32T & 6K32TRC, but local traffic on a port will not consume any
of the bandwidth on any other port.
Magnum 6K32T & 6K32TRC units are plug-and-play devices. There is no
software configuring necessary to be done for basic operation at installation or for
maintenance. The only hardware configuration settings are user options for an UP-LINK
Switch (resides inside the unit) on the 6K8-RJ45 (modular port). Optional Half / Full
duplex mode and 10 or 100Mbps selection for the switched ports must be configured
through MNS-6K software per unit as per the requirement. The internal functions of both
are described below.
Filtering and Forwarding
Each time a packet arrives on one of the switched ports, the decision is taken to
either filter or to forward the packet. Packets whose source and destination addresses are
on the same port segment will be filtered, constraining them to that one port and relieving
the rest of the network from having to process them. A packet whose destination address
is on another port segment will be forwarded to the appropriate port, and will not be sent
to the other ports where it is not needed. Traffic needed for maintaining the operation of
the network (such as occasional multi-cast packets) are being forwarded to all ports.
The Magnum 6K32T & 6K32TRC Switches operate in the store-and-forward
switching mode, which eliminates bad packets and enables peak performance to be
achieved when there is heavy traffic on the network.
Address Learning
All Magnum 6K32T & 6K32TRC units have address table capacities of 4K
node addresses suitable for use in larger networks. They are self-learning, so as nodes are
added, removed or moved from one segment to another, the 6K32T & 6K32TRC Switch
automatically keeps up with node locations.
www
.
GarrettCom . com
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
An address-aging algorithm causes least-used addresses to fall out in favor of
frequently-used addresses. To reset the address buffer, cycle power down-and-up.
4.2
Status LEDs
For all Magnum 6K32T & 6K32TRC models :
PWR
LK
ACT
F/H
: Power LED, ON when external power is applied to the unit.
: Steady ON, Link status for 10 Mbps and 100Mbps operation.
: ON with port activity for 10 Mbps and 100Mbps operation.
: Full / Half duplex LED, ON when the port is running full
duplex, OFF for half duplex.
100/10
: Speed LED, ON when the speed is 100Mbps , OFF when the
speed is 10 Mbps
4.3
Auto-Cross (MDIX)Auto-negotiation, for 10/100Mbps RJ-45 ports
The 24 RJ-45 ports on Magnum 6K32T & 6K32TRC support auto-cross (MDI or
MDIX) in the auto-negotiation mode according to the IEEE 802.3u standard. No
crossover cables are needed when connecting the 6K32T & 6K32TRC’s 10/100
copper ports to other unmanaged switches, legacy hubs, managed switches, media-
converters etc. Please note that there can be conditions with managed switches
where the switch manager fixes the port settings via software, and the result of the
auto-negotiation is changed in the managed switch by the manager commands. In
such cases, the 10/100 speed or the F/H mode may be affected, but auto-cross in the
6K32T & 6K32TRC Switches will still work. The auto-cross function can be
disabled, if fixed the port at 10 or 100Mb through software..
The Managed Magnum 6K32T & 6K32TRC Fast Ethernet copper ports can be
set for either fixed 100Mb speed or N-way auto-negotiation per the IEEE802.3u
standard. The selection is made via 6K-MNS software. The factory default setting
is for auto-negotiation. At 100Mb-fixed speed, the user may select half- or full-
duplex mode by 6K-MNS Software for each RJ-45 port separately. For detail
information see Section 7 (Port Setup) of Magnum 6K32T & 6K32TRC
Software user guide (MNS-6K) . One frequently-used application for the Managed
6K32T & 6K32TRC Switch copper ports is to connect one of them using a fiber
media converter to another Switch in the network backbone, or to some other
remote 100Mb device. In this case, it is desirable to operate the fiber link at 100Mb
speed, and at either half- or full duplex mode depending on the capabilities of the
www
.
GarrettCom . com
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
remote device. Standard commercially available Fast Ethernet media converters
mostly do not support auto-negotiation properly, and require that the switched port
to which they are connected be at 100Mb fixed speed. Attachment to 10/100 auto-
negotiation ports typically will not work properly. The 6K32T & 6K32TRC
Switch’s RJ-45 ports handle this situation by configuring the ports as per desire
through MNS software port settings and can check the port status of each port after
the change.
When Magnum 6K32T & 6K32TRC RJ-45 copper ports are set for auto-
negotiation and are connected to another auto-negotiating device, there are 4 different
speed and F/H modes possible depending on what the other device supports. These are:
(1) 100Mb full-duplex, (2) 100Mb half-duplex, (3) 10 Mb full-duplex and (4) 10 Mb
half-duplex.
General information -
Auto-negotiation per-port for 802.3u-compliant switches occurs when:
-- the devices at both ends of the cable are capable of operation at either 10
Mb or 100Mb speed and/or in full- or half-duplex mode, and can
send/receive auto-negotiation pulses, and . . .
-- the second of the two connected devices is powered up*, i.e., when
LINK is established for a port, or
-- the LINK is re-established on a port after being lost temporarily.
•
NOTE – Some NIC cards only auto-negotiate when the computer system
that they are in is powered up. These are exceptions to the “negotiate at
LINK – enabled” rule above, but may be occasionally encountered.
The auto-negotiation logic will attempt to operate in descending order and will normally
arrive at the highest order mode that both devices can support at that time. (Since auto-
negotiation is potentially an externally controlled process, the original “highest order
mode” result can change at any time depending on network changes that may occur). If
the device at the other end is not an auto-negotiating device, the 6K32T & 6K32TRC’s
www
.
GarrettCom . com
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
RJ-45 ports will try to detect its idle signal to determine 10 or 100 speed, and will default
to half-duplex at that speed per the IEEE standard.
When operating in 100Mb half-duplex mode, cable distances and hop-counts
may be limited within that collision domain. The Path Delay Value (PDV) bit-times must
account for all devices and cable lengths within that domain. For Magnum 6K32T &
6K32TRC Fast Ethernet switched ports operating at 100Mb half-duplex, the bit time
delay is 50BT.
4.4
Flow-control, IEEE 802.3x standard
Magnum 6K32T & 6K32TRC Switches incorporate a flow-control mechanism
for Full-Duplex mode. The purpose of flow-control is to reduce the risk of data loss if a
long burst of activity causes the switch to save frames until its buffer memory is full.
This is most likely to occur when data is moving from a 100Mb port to a 10 Mb port and
the 10Mb port is unable to keep up. It can also occur when multiple 100Mb ports are
attempting to transmit to one 100Mb port, and in other protracted heavy traffic situations.
Magnum 6K32T & 6K32TRC Switches implement the 802.3x flow control
(non-blocking) on Full-Duplex ports, which provides for a “PAUSE” packet to be
transmitted to the sender when the packet buffer is nearly filled and there is danger of
lost packets. The transmitting device is commanded to stop transmitting into the 6K32T
& 6K32TRC Switch port for sufficient time to let the Switch reduce the buffer space
used. When the available free-buffer queue increases, the Switch will send a “RESUME"
packet to tell the transmitter to start sending the packets. Of course, the transmitting
device must also support the 802.3x flow control standard in order to communicate
properly during normal operation.
Note: When in Half-Duplex mode, the 6K32T & 6K32TRC Switch implements a back-
pressure algorithm on 10/100 Mb ports for flow control. That is, the switch prevents
frames from entering the device by forcing a collision indication on the half-duplex ports
that are receiving. This temporary “collision” delay allows the available buffer space to
improve as the switch catches up with the traffic flow.
5.0
Magnum 6K32T & 6K32TRC Managed Switch Port Modules
This chapter describes each Port Module (PM), including appearance,
functionality, and status displays.
www
.
GarrettCom . com
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
5.1
Inspecting the Package and Product
This section applies only to PMs shipped as separate items, i.e., 6K32T &
6K32TRC PMs not factory installed in a Magnum 6K32T & 6K32TRC
modular slot.
Examine the shipping container for obvious damage prior to
installing a 6K32T & 6K32TRC PM; notify the carrier of any damage you
believe occurred during shipment or delivery. Inspect the contents of this
package for any signs of damage and ensure that the items listed below are
included.
This package should contain:
6K32T & 6K32TRC PMs
Installation instructions, with illustrations
Remove the 6K32T & 6K32TRC PM(s) from the shipping container.
Be sure to keep the shipping container should you need to ship any of the PMs
separately at a later date. In the event there are items missing or damaged,
contact your supplier. If you need to return the unit, use the original shipping
container if possible. Refer to Chapter 5 for specific return procedures.
5.2
6KPM Module Description
An important feature of the Magnum 6K32T & 6K32TRC is the use
of one Port Modules for flexible mixed-media connectivity to RJ-45 and fiber
media in the modular slot. Since the Magnum 6K32T & 6K32TRC Switches
have dual-speed capability for copper ports, the 6 or 8-port interfaces are
designed to support all standard Ethernet media types at 10 or 100Mps speed.
Each 6K32T & 6K32TRC PM can provide two, four, six or eight ports for
connecting Ethernet segments with its individual connector type and media.
For a list of 6K32T & 6K32TRC Port Module types, refer to Section 1.2
Each 6K PM is individually described in the following sections.
NOTE: The port #1 on the RJ-45 ports on all the modules, either all
RJ-45 ports or used for COMBO module is set as (=) as other ports.
www
.
GarrettCom . com
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
5.2.1
6KP6-RJMST, 4@10/100Mbps RJ-45 and 2@100Mb multi-mode
FX-ST “twist
lock” Combo
Module
6KP6-RJMST,
4 Port@ 10/100Mbps and 2 @100 Mb ST Fiber Port
2
The Magnum 6KP6-
1
1
3
5
7
LK
10/100
F/H
RJMST is a combo 6 port
module of RJ-45’s at
ACT
ACT
ACT
F/H
F/H
4
10/100Mbps and fiber optic
ports at 100MB. The Combo
module is equipped with dual-
mode ST-type connectors and
TX
LK RX
2
TX LKRX
6
3
1
3
2
4
LINK
10/100
ACTIVITY
FULL/HALF
dual speed copper ports. The ST-connector functions as a fiber optic transceiver to
support 100BASE-FX network segments. When installed in a Magnum 6K32T &
6K32TRC Managed Switch, the copper port supports the standard distance 100m on each
port and the fiber port supports fiber optic cable distances up the IEEE-standard
100Mbps distance limits, i.e., typically 2km at full-duplex and 412m at half-duplex.
Each port has an Activity (ACT) LED indicating packets being received, a
Link (LK) LED that indicates proper connectivity with the remote device when lit, and
FDX/HDX LED to indicate full-duplex mode when lit (or half-duplex when off). The
10/100 LED indicates the speed, if the LED is ON 100Mbps if it is OFF 10Mbps.
5.2.1a 6KP6-RJ10ST, 4@10/100Mbps RJ-45 and 2@10Mb multi-mode
FX-ST “twist lock” Combo Module
The 6KP6-RJ10ST is a six port combo module that looks similar to
the 100Mb combo module with the exception of 10Mb speed at the ST fiber module.
The ST-connector functions as a fiber optic transceiver to support 10BASE-FX network
segments. When installed in a Magnum 6K32T & 6K32TRC Managed Switch, the
copper port supports the standard distance 100m on each port and the fiber port supports
fiber optic cable distances up the IEEE-standard 10Mbps distance limits, i.e., typically
2km at full-duplex and half-duplex.
Each port has an Activity (ACT) LED indicating packets being received, a
Link (LK) LED that indicates proper connectivity with the remote device when lit, and
FDX/HDX LED to indicate full-duplex mode when lit (or half-duplex when off). The
10/100 LED indicates the speed, if the LED is ON, 100Mbps if it is OFF, 10Mbps.
www
.
GarrettCom . com
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
5.2.1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST “twist lock” Module
6KP4-RJ10MST,
The Magnum 6KP4-F10ST
is a 10Mb multi-mode
4 Port@ 10Mb ST Fiber Port
2
fiber module with 4 ST-
Fiber ports. All four fiber
ports are ST connectors
and configured as 10Mb
Half-duplex by default.
The 10Mb ST-fiber ports
allow the user to connect
their legacy 10Mb network
to the Magnum 6K32T &
ACT
F/H
ACT
F/H
5
1
TX LK RX
TX LK RX
1
3
ACT
F/H
2
ACT
F/H
6
T
LK RX
TX LK RX
1
ACTIVITY
2
LINK
3
FULL/HALF
6K32TRC switch. They also provide a convenient way for the half duplex
hub to connect to the switch through 10Mb fiber ports. It supports distances according to
the 10Base-FL standard i.e, 2Km distance for multi-mode fiber. (Single-mode for 10Km
distance may be available as a special order).
6KP4-RJ10MST,
Each port
4 Port@ 10Mb ST Fiber Port
has an Activity (ACT) LED
2
indicating packets being
received, a Link (LK) LED
ACT
F/H
1
ACT
F/H
5
indicating proper
1
TX LK RX
TX LK RX
3
connectivity with the remote
device when lit, and
ACT
F/H
2
ACT
F/H
6
T
LK RX
TX LK RX
FDX/HDX LED indicating
full-duplex mode when lit (or
half-duplex if off).
1
3
ACTIVITY
2
LINK
FULL/HALF
5.2.1c 6KP4-FLSTFX, 2@10Mb and 2@100Mb multi-mode FX-ST “twist
lock” Module
The Magnum 6KP4-FLSTFX is a combo fiber module with two 10Mb + two 100Mb
multi-mode fiber module and in combine 4 ST-Fiber ports. All four fiber ports are ST
www
.
GarrettCom . com
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
connectors and configured as 10Mb Half-duplex by default for 10Mb fiber and 100Mb
Full duplex for the 100Mb fiber. The 10Mb ST-fiber ports allow the user to connect their
legacy 10Mb network to the Magnum 6K32T & 6K32TRC switch. They also provide a
convenient way for the half duplex hub to connect to the switch through 10Mb fiber
ports. Whereas the 100Mb ST module allow to connect the 100Mb demand of Switch
devices. It supports distances according to the 10Base-FL standard i.e, 2Km distance for
multi-mode fiber. (Single-mode for 10Km distance may be available as a special order).
Each port has an Activity (ACT) LED indicating packets being
received, a Link (LK) LED indicating proper connectivity with the remote device when
lit, and FDX/HDX LED indicating full-duplex mode when lit (or half-duplex if off).
5.2.2. 6KP6-RJMSC 4@10/100Mbps RJ-45 and 2@100Mb multi-mode FX-SC
“snap-in” Fiber connector
6KP6-RJMSC,
The Magnum 6KP6-
4 Port@ 10/100Mbps and 2 @100 Mb SC Fiber Port
RJMSC is also a Combo 6 Port
2
module equipped with 4 10/100Mb
RJ-45 ports along with 2 multi-
mode 100Mbps fiber optic
1
1
3
5
7
LK
10/100
F/H
ACT
ACT
ACT
F/H
6
F/H
4
TX
LK RX
2
TX LK RX
3
transceivers all in one module. This
is similar to the 6K6-RJMST. It has
the same LEDs indicating port
activity (ACT), Link (LK), and
1
3
2
LINK
10/100
FULL/HALF
4
ACTIVITY
FDX / HDX and 10/100 operation, and the same face-plate lettering.
While the functionality of these two modules is essentially the same, the 6KP6-
RJMSC is equipped with an SC-type "snap-in" connector instead of an ST-type.
www
.
GarrettCom . com
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
5.2.3 6KP6-RJSSC 4@ 10/100Mbps RJ-45 Ports and 2@100Mbps single-mode
FX-SC-type,
“snap-in”
connector
6KP6-RJMSSC,
4 Port@ 10/100Mbps and 2 @100 Mb SSC Fiber Port
2
The Magnum 6KP6-RJSSC
is also a Combo module
equipped with 4 dual speed
copper ports and 2 Single-
mode SC-type connectors. It
provides an advantage
1
1
3
5
7
LK
10/100
F/H
ACT
ACT
ACT
F/H
6
F/H
4
TX
LK RX
2
TX LKRX
3
1
3
2
LINK
10/100
FULL/HALF
4
ACTIVITY
through combining copper
and Fiber functions in one module of the 6K32T & 6K32TRC Switch supporting four
Copper and two single-mode fiber network segments.
The 6KP6-RJSSC, when installed in a Magnum 6K32T & 6K32TRC Switch
operates on copper at the 100m distance. The Fiber is single-mode and cable lengths can
be as much as 25+ Km (see Power Budget, Section 4.5)
Each port has an Activity (ACT) LED indicating packets being received, a
Link (LK) LED that indicates proper connectivity with the remote device when lit, and a
FDX/HDX LED to indicate full-duplex mode when lit (or half-duplex when off). The
10/100 LED indicates 100Mbps speed when lit and 10Mbps speed when off. To
distinguish the single-mode 6 K6-RJSSC from the multi-mode 6K6-RJMSC, the label
“Sgl. M.” is at the top of the faceplate of the 6K6-RJSSC.
5.2.4
6KP6-RJSSCL 4 @ 10/100 Mb copper port and 2@100Mbps single-mode
FX-SC-type, “snap-in” connector
The Magnum 6KP6-RJSSC is also a Combo module equipped with 4 dual speed copper
ports and 2 Single-mode (Long Reach) SC-type connectors. It provides a combination of
copper and Fiber functions in one module to the 6K32T & 6K32TRC Switches,
supporting four Copper and two single-mode (Long-Reach) fiber network segments.
The 6KP6-RJSSC, when installed in a Magnum 6K32T & 6K32TRC Switch
has copper supporting the 100m distance and Fiber supporting single-mode fiber cable
lengths of as much as 40+ Km (see Power Budget, Section 4.5)
www
.
GarrettCom . com
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Each port has an Activity (ACT) LED indicating packets being received, a
Link (LK) LED indicating proper connectivity with the remote device when lit, and a
FDX/HDX LED indicating full-duplex mode when lit (or half-duplex when off). The
10/100 LED indicates the speed for the copper port, which is 100Mbps when the LED is
ON and 10 Mb when the LED is OFF.
5.2.4a 6KP6-RJ10ST 4 @ 10/100 Mb copper port and 2@10Mbps multi-mode
FL-ST-type, “twist-lock” connector
The Magnum 6KP6-RJ10ST is also a Combo module equipped with 4 dual speed copper
ports and 2 multi-mode 10 Mb fiber ST-type connectors. It provides a combination of
copper and Fiber functions in one module to the 6K32T & 6K32TRC Switches,
supporting four Copper and two 10Mb of ST fiber network segments.
The 6KP6-RJ10ST, when installed in a Magnum 6K32T & 6K32TRC Switch
has copper supporting the 100m distance and Fiber supporting multi-mode fiber cable
allow to connect the legacy network of 10Mb requirement in the network. Each port has
an Activity (ACT) LED indicating packets being received, a Link (LK) LED indicating
proper connectivity with the remote device when lit, and a FDX/HDX LED indicating
full-duplex mode when lit (or half-duplex when off). The 10/100 LED indicates the
speed for the copper port, which is 10Mbps when the LED is ON and 10 Mb when the
LED is OFF.
5.2.5 6KP8-MTRJ, 8 @100Mb multi-mode FX , MTRJ Small-Form-factor
Magnum 6KP8-
6KP8-MTRJ,
“small-form-factor”
MTRJ is a multi-mode fiber
optic 8-port module equipped
with a small-form-factor
8 Port@ 100Mbps Multi-Mode Fiber port
1
MTRJ-type connector. It looks
almost like an RJ-45 port, but it
is black in color. The MT-RJ’s
small size and ease of
1
3
5
7
ACT
ACT
F/H
ACT
F/H
ACT
F/H
F/H
LK
LK
LK
LK
2
ACT
ACT
F/H
ACT
F/H
ACT
F/H
F/H
LK
LK
LK
LK
3
2
4
6
8
connection make it a good
choice for 100Mbps “fiber-to-
the-desktop” Ethernet
1
3
ACTIVITY
LINK
2
FULL/HALF
www
.
GarrettCom . com
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
connectivity. When installed in a Magnum 6K32T & 6K32TRC Switch, it supports fiber
optic cable distances up the IEEE-standard 100Mbps distance limits, i.e., typically 2km
at full-duplex and 412m at half-duplex.
The functionality of this 100BASE-FX multi-mode 8 Port module is essentially
the same as the ST and SC-types. It has the same LEDs per port indicating port activity
(ACT), Link (LK), and FDX or HDX operation.
5.2.5a 6KP6-MT10ST, 4 @100Mb multi-mode FX , MTRJ Small-Form-
Factor and 2@ 10Mb Multi-mode ST-Fiber port
The 6KP6-RJ10ST is a combo module with two different kinds of fiber flavor
with two different speeds. The top four ports of MTRJ Small form factor fiber support at
100Mb full-duplex, whereas the bottom two ports multi-mode ST-Fiber support 10Mb
half-duplex. This combo module provides more flexibility to the user to connect their
legacy 10Mb fiber as well as 100Mb to the Magnum 6K32T & 6K32TRC Switch.
When installed in a Magnum 6K32T & 6K32TRC Switch, the 100Mb MTRJ
connector supports fiber optic cable distances up to the IEEE-standard 100Mbps distance
limits, i.e., typically 2km at full-duplex and 412m at half-duplex. The 10Mb Multi-mode
ST-Fiber connector supports the standard fiber optic distance limit of 2Km at Full and
Half-duplex both.
The functionality of this 100BASE-FX multi-mode 4 port module is
essentially the same as the ST and SC-types. It has the same LEDs per port
indicating port activity (ACT), Link (LK), and FDX or HDX operation
www
.
GarrettCom . com
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
5.2.6
FX ,
6KP8-45MT, 4@ 10/100Mbps RJ-45 and 4@100Mb multi-mode
MTRJ Small-Form-Factor
The Magnum 6KP8-45MT
6KP8-45MT
Module is a combo module with
copper and fiber (Small Form Factor)
MTRJ type ports. The small size of
MTRJ connectors give an advantage
of placing more ports on one module.
The 6KP8-45MT is equipped with 4
10/100 RJ-45 ports and 4 MTRJ fiber
ports.
4 Port@ 10/100Mbps & 4 port @ 100Mbps
Multi-Mode Fiber port
2
1
1
3
5
7
LK
10/100
4
ACT
F/H
ACT
ACT
F/H
F/H
ACT
F/H
F/H
LK
LK
LK
6
LK
8
2
4
3
1
3
2
4
LINK
ACTIVITY
10/100
FULL/HALF
When installed in a Magnum 6K32T
& 6K32TRC Switch, it supports the
standard distances as mentioned on 5.2.3. and the LEDs also act similarly.
5.2.7
6KP8-MLC, 8 ports @ 100Mbps multi-mode LC connector Small-
8Port@ 100Mbps MLC Ports
Form Factor
-
3
Magnum 6KP8-MLC is a eight-port multi-
1
3
5
F/H
7
ACT
ACT
F/H
ACT
mode fiber LC connector “small-form-factor”
used primarily in 100Mbps fiber-to-the-
desktop links. When installed in a Magnum
ACT
F/H
F/H
LK
LK
LK
LK
2
2
4
6
ACT
ACT
F/H
A
H
CT
ACT
F/H
1
F/H
LK
LK
LK
LK
2
8
4
6
6K32T & 6K32TRC Switch, it supports fiber optic
cable distances up to the IEEE-standard 100Mbps
distance limits, i.e., typically 2km at full-duplex and
ACTIVITY
LINK
1
3
2
FULL/HALF
412m at half-duplex.
The compact size of the LC Connector reduces the size of wiring panels in
wiring closets while providing the advantage of “future-proof” fiber optic technology.
The cable end is a “plug-in” connector with both fiber strands terminated in
one housing that cannot be improperly inserted. Each port has an Activity (ACT) LED
indicating packets being received, a Link (LK) LED indicating proper connectivity with
the remote device when lit, and a FDX/HDX LED indicating full-duplex mode when lit
(or half-duplex when off).
www
.
GarrettCom . com
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
5.2.8
6KP8-45LC, Combo 4@ 100Mbps multi-mode -LC small-form
factor and 4@ 10/100 Mbps RJ-45 Connector
The Magnum 6KP8-
45LC Module is a combo module
with a combination of copper and
Fiber (Small Form Factor) LC
type ports. The small size of LC
connectors allows an advantage of
having more ports on one module.
The 6KP8-45LC is equipped with
4 10/100 RJ-45 ports and 4 LC(
Small form factor) multi-mode
fiber ports.
4 Port@ 10/100Mbps & 4 port @ 100Mbps
Multi-Mod LC Fiber port
2
1
1
3
5
LK
10/10
4
ACT
ACT
F/
AC
F/H
AT
F/H
AC
F/H
F/H
LK
LK
LK
2
4
6
3
1
3
2
4
LINK
ACTIVITY
10/10
FULL/HALF
When installed in a Magnum 6K32T & 6K32TRC Switch, it supports the standard
distances as per mentioned on 5.2.8. and the LEDs also acts similarly as mentioned
above.
5.2.9
6KP8-RJ45
(Twisted Pair),
6KP8-RJ45,
10/100Mb 8-Port
8 Port@ 10/100Mb Copper ports
The 6KP8-RJ45
2
1
1
3
5
7
module supports Ethernet
twisted pair segments of any
standard length. It is
LK
10/100
ACT
F/ H
2
4
6
8
10/100
LK
4
3
F/H
equipped with an eight-port
RJ-45 connector, and offers
10/100 full / half-duplex
auto-negotiating capability
on each port. The RJ-45
ACT
1
3
2
4
LINK
10/100
FULL/HALF
ACTIVITY
connector is shielded to minimize emissions and will allow both unshielded twisted pair
(UTP) and shielded twisted pair (STP) cable connections. The 6KP8-RJ45 module is
equipped with a Media Dependent Auto-Crossover (MDI-X) switch, which controls all
www
.
GarrettCom . com
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
ports for cascaded connection. This feature eliminates the need for a special twisted pair
crossover cable when connecting to a hub or another switch.
Each port has an Activity (ACT) LED indicating packets being received, a
Link (LK) LED that indicates proper connectivity with the remote device when lit, a
FDX/HDX LED to indicate full-duplex mode when lit (or half-duplex when off), and a
“10/100” LED indicating 100Mb when lit (or 10 Mbps when off).
Important Note: The 10/100 RJ-45 ports are supported with Auto-negotiation and
Auto-crossover (MDIX), which allow the RJ-45 ports to automatically Link with any RJ-
45 device and eliminate the use of cross-over cable.
The RJ-45 pins normally (TP crossover switch) are per the standard for hubs-to-
users twisted pair wiring: 1 = receive+, 2 = receive-, 3 = transmit+, 6 = transmit-,
other pins not used. When the TP crossover push-button is UP, the pins of the RJ-
45 port are per the standard for up-links using twisted pair wiring, i.e., the transmit
and the receive pairs are exchanged: 1 = transmit+, 2 = transmit-, 3 = receive+, 6 =
receive-, other pins not used.
NOTE: for Power Substations: In support of the IEEE 1613 Class 2 standard, GCI
advises that, for substation applications, the RJ-45 ports are intended for
connectivity to other communication equipment such as routers or
telecommunication multiplexers installed in close proximity (i.e., less than 2
meters or 6.5ft) to the 6K32. It is not recommended to use these ports in
substation applications to interface to field devices across distances which
could produce kigh (greater than 2500V ) levels of ground potential rise (GPR)
during line-to-ground fault conditions. The 6K32 passes the 1613specifications
for zero packet loss with fiber ports & with RJ45 ports used as indicated here.
5.2.10a. New PoE (Power Pass-through), model P6KP8V-RJ45 (MDIX), 10/100Mb
8-port
The PoE RJ-45 ports act similar to regular RJ-45 ports, except they have
capability of providing power on each port to power up the PD devices, per the
IEEE802.3af PoE standard. The Power Pass-through PoE modules are totally dependent
upon the powerful -48VDC input power supply to support more RJ-45 (10/100) ports.
Each port requires at least 15watts to power up the PoE PD devices. In this Fig. the top 8-
RJ45 ports are enhanced with POE option The 8-RJ45 POE modules are also available
with mix –n-match with fiber modules. Please check the ordering information Sec.1.2 for
all the various P6K PoE modules option.
www
.
GarrettCom . com
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
The LEDs on 6KP8-RJ45- PoE modules are slightly different compared to
regular (non-PoE) RJ-45 modules as shown in Fig 2. When the PoE port is in use, the
PoE LED is ON when connected properly to an 803.af compliant PD device on that port.
When non-PoE devices are connected, the PoE LED is OFF. PoE does not affect
operation of Ethernet data traffic.
LINK and ACTIVITY LEDS are combined on the PoE modules into one LED
that is marked as LINK/ACT, as shown in the diagram.
PoE LEDs Summary
•
For PoE devices, each RJ-45 PoE port supports only 802.3af complaint
devices. The PoE LED is ON when the attached PD is drawing power from the
port.
•
•
For non-PoE devices connected, the PoE port will act as a normal RJ-45 port
and the PoE LED is OFF. No power is being sent out from the port.
The PoE ports in Magnum 6K’s with 48VDC power input act as a pass-
through, so the 48VDC power source must be strong enough to provide power
to the 6K switch and to all the 8 RJ-45 ports with PD devices connected (up to
15 watts per PoE port).
•
In the case where the 48VDC power in not internally connected and no power
is coming to the PoE ports for some reason, all the PoE port LEDs are ON
simultaneously to indicate a trouble condition. The ports will still operate
properly for data traffic.
5.2.10b. New PoE(Power Inside), model PI6KP8-45RJ (MDIX), 10/100Mb 8-port
The PoE RJ-45 ports act similar to regular RJ-45 ports, except they have
capability of providing power on each port to power up the PD devices, per the
IEEE802.3af PoE standard. Only 4 x RJ-45 (10/100) ports maxm. support POE(Power
www
.
GarrettCom . com
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Inside) option in one 6K-unit. In this Fig. the top 4-RJ45 ports are enhanced with POE
option whereas as bottom 4- RJ-45 are normal MDIX ports. The 4-RJ45 POE module are
also available with mix –n-match with fiber modules. Please check the ordering
information Sec.1.2. for all the various PI6K PoE modules option.
The LEDs on 6KP8-RJ45- PoE module are slightly different compared to
regular (non-PoE) RJ-45 modules as shown in Fig 2. When the PoE port is in use, the
PoE LED is ON when connected properly to a 803.af compliant PD device on that port.
When non-PoE devices are connected, the PoE LED is OFF. Operation of Ethernet data
traffic is not affected by PoE.
LINK and ACTIVITY LEDS are combined on the PoE modules into one LED
that is marked as LINK/ACT, as shown in the diagram.
PI6KP8V-45RJ
8 Port@ 10/100Mb POE Copper ports
2
1
3
5
LK/ACT
10/10
0
1
PO
E
F/
H
2
4
6
8
10/10
LK/ACT
0
F/H
PO
E
4
3
LK/ACT
PoE
10/100
FULL/HALF
1
2
4
3
PoE LEDs Summary
•
For PoE devices, each RJ-45 PoE port supports only 802.3af complaint
devices. The PoE LED is ON when the attached PD is drawing power from the
port.
•
•
For non-PoE devices connected, the PoE port will act as a normal RJ-45 port
and the PoE LED is OFF. No power is being sent out from the port.
The PoE ports in Magnum 6K’s with 48VDC power input act as a pass-
through, so the 48VDC power source must be strong enough to provide power
to the 6K switch and to all the 8 RJ-45 ports with PD devices connected (up to
15 watts per PoE port).
•
In the case where the
6KP86KP8V- -45-2MT
48VDC power in not
internally connected and
no power is coming to
the PoE ports for some
reason, all the PoE port
LEDs are ON
6 Port@10/10Mbps and 2 port @100Mb
Multi-Mode Fiber port
2
1
1
3
5
L
10/10
simultaneously to
indicate a trouble
4
AC
F/H
ACT
10/100
F/H
condition. The ports will
still operate properly for
data traffic.
F/H
LK
F/H
2
4
6
3
2
4
1
10/100
LINK
3
ACTIVITY
FULL/HALF
www
.
GarrettCom . com
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
5.2.11 6KP8-45-2MT, 6@ 10/100Mbps RJ-45 and 2@100Mb multi-mode
FX , MTRJ Small-Form-Factor
The Magnum 6KP8-45-2MT eight port Module is a combo module with copper
and fiber (Small Form Factor) MTRJ type ports. The small sizes of MTRJ connectors
give an advantage of placing more fiber ports on one module. The 6KP8-45-2MT is
equipped with six 10/100 RJ-45 ports and two 100Mb MTRJ fiber ports. When installed
in a Magnum 6K32T & 6K32TRC Switch, it supports the standard distances as
mentioned on 5.2.3. and the LEDs also act similarly.
5.2.11a 6KP8-45-2LC, 6@
-
6 Port@ 10/100Mbps & 2 port @ 100Mbps
10/100Mbps RJ-45 and
2@100Mb single-mode FX ,
LC Small-Form-Factor
Singl-eMode Fiber port
2
The Magnum 6KP8-
1
1
3
5
LK
10/10
45SLC eight port Module is a combo
module with copper and fiber (Small
Form Factor) LC type fiber ports.
4
10/100
ACT
F/H
ACT
F/
A
F/
LK
F/H
2
4
6
3
The small size of LC connectors
give an advantage of placing more
ports on one module. The 6KP8-45-
2
LINK
1
3
10/100
ACTIVITY
FULL/HALF
4
2SLC is equipped with 6 10/100 RJ-45 ports and 2 Single-mode fiber ports.
When installed in a Magnum 6K32T & 6K32TRC Switch, it supports the standard
distances as mentioned on 5.2.4. and the LEDs also act similarly.
5.2.12 GBIC-SXSC Gigabit fiber(1000Mb), multi-mode SC Connector
The Magnum GBIC-SXSC is a multi-mode Gigabit fiber connector
equipped with SC type connectors and can be easily snapped in and out. The Gigabit
fiber ports are most
to-switch and switch-to-
It supports cable
popular as server-
switch applications.
distances up to the
1000Mbps distance
duplex.
ACT
F/
TX LK RX
1
3
5
7
L
10/100
IEEE 802.3z standard
limits, i.e., 550m at full
ACT
F/
1@ 1000Mb Fiber SC + 4@10/ 100Mb
www
.
GarrettCom . com
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
The GBIC transceiver has been offered in the modular slot with multiple options as per
the user requirement. The two Giga port has been offered as GBPM-2OTX (fiber or RJ-
45), whereas the single Gigabit module comes in flavor of G+2 (100Mb fiber ports) or
G+4(10/100 RJ-45 ports) as shown in the above figure.
The GBIC transceiver is fastened using snap-in clips. Insert the transceiver
(take care to insert it the right way up, arrows on top) until it clicks in space. While
removing the transceiver, press the clips on either side of the transceiver at the same time
and pull the transceiver out.
Each port has an Activity (ACT) LED indicating packets being received and a
Link (LK) LED indicating proper connectivity with the remote device when lit.
5.2.12a GBPM-2OTX (Two Gigabit option)
The Magnum 6K16-Series offered a wide
selection of Gigabit speed with multiple
choice of copper or Fiber or mix for the
modular slot via GBPM-2OTX (2 x Giga
module). While up to two Gigabit modules
(maxm.) can be configured in the modular
slot for GBPM-2OTX. The Dual Gigabit
port option for the modular slot
provide a wide option of choice for various Gigabit transceivers covering a long range of
distance. The GBPM-2OTX also meets the requirement for those applications where a
managed Gigabit media converter is required. The two Gigabit slot can be filled with
copper/Fiber or mix as per the application.
The 6K16-Series Modules provide a GBIC opening for insertion of industry-
standard GBICs to provide Gigabit (Gb) transceivers media flexibility. GBIC models are
available for both multi-mode (550m) and single-mode (10, 25, 40, 70) km fiber options,
and Gigabit copper as well, with new models appearing often.
www
.
GarrettCom . com
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Each port has an Full and Half Duplex (F/H) Activity, (ACT) LED indicating
packets being received and a Link (LK) LED indicating proper connectivity with the
remote device when lit
5.2.12b GBIC-LXSC Gigabit fiber (1000Mb), multi-mode SC Connector
The Magnum GBIC-LXSC is a single-mode Gigabit fiber connector equipped
with SC type connectors and can be easily snapped in and out. The Gigabit fiber ports are
most popular as server-to-switch and switch-to-switch applications. It supports cable
distances up to the IEEE 802.3z standard 1000Mbps distance limits, i.e., 10,25, 40 or
70Km at full duplex, and depend upon the Gigabit modules used.
ACT
F/
TX LK RX
ACT
F/
ACT
F/
TX LK RX
TX
L
RX
1@ 1000Mb Fiber SC + 2@ 100Mb SC
The two Giga port has been offered as GBPM-2OTX (fiber or RJ-45), whereas the single
Gigabit module comes in flavor of G+4(10/100 RJ-45 ports) or G+2 (100Mb fiber ports)
as shown below in the above figure.
Each port has an Activity (ACT) LED indicating packets being received and a link (LK)
LED indicating proper connectivity with the remote device when lit.
5.2.13 6KM-BLNK
The 6K8-BLNK is a
blank face plate or cover plate that
must be installed in any empty
6K32T & 6K32TRC PM slot to
maintain proper cooling air flow,
safety, etc.
Two screws underneath the front panel hold the 6KM-BLNK in place.
www
.
GarrettCom . com
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
6.0
TROUBLESHOOTING
All Magnum Ethernet products are designed to provide reliability and
consistently high performance in all network environments. The installation of a
Magnum 6K32T & 6K32TRC Switch is a straightforward procedure (see
INSTALLATION, Section 3.0); the operation is also straightforward and is discussed in
Section 4.
Should problems develop during installation or operation, this section is
intended to help locate, identify and correct these types of problems. Please follow the
suggestions listed below prior to contacting your supplier. However, if you are unsure of
the procedures described in this section or if the Magnum 6K32T & 6K32TRC Switch is
not performing as expected, do not attempt to repair the unit; instead contact your
supplier for assistance or contact GarrettCom Customer Support.
6.1
Before Calling for Assistance
1.
If difficulty is encountered when installing or operating the unit, refer back to
the Installation Section of the applicable chapter of this manual. Also check
to make sure that the various components of the network are interoperable.
2.
3.
4.
Check the cables and connectors to ensure that they have been properly
connected and the cables/wires have not been crimped or in some way
impaired during installation. (About 90% of network downtime can be
attributed to wiring and connector problems.)
Make sure that an AC power cord is properly attached to each Magnum 6K32T
& 6K32TRC Switch unit. Be certain that each AC power cord is plugged into
a functioning electrical outlet. Use the PWR LEDs to verify each unit is
receiving power.
If the problem is isolated to a network device other than the Magnum 6K32T &
6K32TRC Switch product, it is recommended that the problem device be
replaced with a known good device. Verify whether or not the problem is
corrected. If not, go to Step 5 below. If the problem is corrected, the Magnum
6K32T & 6K32TRC Switch and its associated cables are functioning properly.
5.
Always check your Switch configuration, specially Auto-negotiation behavior
with other connected device to have proper setup tested.
www
.
GarrettCom . com
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
5.
If the problem continues after completing Step 4 above, contact your supplier
of the Magnum 6K32T & 6K32TRC Switch unit or if unknown, contact
assistance.
6.2
When Calling for Assistance
Please be prepared to provide the following information.
1.
A complete description of the problem, including the following points:
a. The nature and duration of the problem;
b. Situations when the problem occurs;
c. The components involved in the problem; (complete Network diagram
preferred)
d. Any particular application, environment, power spike that, when used,
appears to create the problem;
2.
3.
4.
An accurate list of GarrettCom product model(s) involved, with serial
number(s). Include the date(s) that you purchased the products from your
supplier.
It is useful to include other network equipment models and related hardware,
including personal computers, workstations, terminals and printers; plus, the
various network media types being used.
A record of changes that have been made to your network configuration prior
to the occurrence of the problem. Any changes to system administration
procedures should all be noted in this record.
6.3
Return Material Authorization (RMA) Procedure
All returns for repair must be accompanied by a Return Material Authorization
(RMA) number. To obtain an RMA number, please use this URL -
https://rma.garrettcom.com/rma/rma_request_noaccount.php to fill out the form.
Please have the following information readily available:
Name and phone number of your contact person.
Name of your company / institution
Your shipping address
www
.
GarrettCom . com
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
Product name
Serial Number (or Invoice Number)
Packing List Number (or Sales Order Number)
Date of installation
Failure symptoms, including a full description of the problem.
GarrettCom will carefully test and evaluate all returned products, will repair products
that are under warranty at no charge, and will return the warranty-repaired units to
the sender with shipping charges prepaid (see Warranty Information, Appendix A,
for complete details). However, if the problem or condition causing the return
cannot be duplicated by GarrettCom, the unit will be returned as:
No Problem Found.
GarrettCom reserves the right to charge for the testing of non-defective
units under warranty. Testing and repair of product that is not under warranty will
result in a customer (user) charge.
6.4
Shipping and Packaging Information
Should you need to ship the unit back to GarrettCom, please follow these
instructions:
1. Package the unit carefully. It is recommended that you use the original
container if available. Units should be wrapped in a "bubble-wrap" plastic
sheet or bag for shipping protection. ( You may retain all connectors and this
Installation Guide.)
CAUTION Do not pack the unit in Styrofoam "popcorn" type packing
:
material. This material may cause electro-static shock damage to the unit.
2. Clearly mark the Return Material Authorization (RMA) number on the
outside of the shipping container.
3. GarrettCom is not responsible for your return shipping charges.
4. Ship the package to:
GarrettCom, Inc.
47823 Westinghouse Dr.
Fremont, CA 94539-7437
Attn.: Customer Service
APPENDIX A: WARRANTY INFORMATION
GarrettCom, Inc. warrants its products to be free from defects in materials
and workmanship for a period of three (3) years from the date of shipment by
GarrettCom.
www
.
GarrettCom . com
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
During this warranty period, GarrettCom will repair or, at its option,
replace components in the products that prove to be defective at no charge other
than shipping and handling, provided that the product is returned pre-paid to
GarrettCom.
This warranty will not be effective if, in the opinion of GarrettCom, the
product has been damaged by misuse, misapplication, or as a result of service or
modification other than by GarrettCom.
GarrettCom reserves the right to make a charge for handling and
inspecting any product returned for warranty repair which turns out not to be
faulty.
Please complete the warranty card as this acts as a product registration,
and mail it to GarrettCom within two weeks of your purchase.
APPENDIX B : Internal DC Power Supply Options
B1.0
SPECIFICATIONS FOR MAGNUM 6K32T & 6K32TRC SWITCHES, DC
POWER
Power Supply (Internal -48VDC Option)
DC Power Connector: 3 terminals: “-“, “GND”, “+”
Input Voltage: 36 - 70 VDC
Power Consumption: Same as for AC models (see Section 1.1)
Power Supply (Internal 24 VDC Option) Industrial Applications
DC Power Connector: 3 terminals: “-“, “GND”, “+”
Input Voltage:
20 - 36 VDC
Power Consumption: Same as for AC models (see Section 1.1)
Power Supply (Internal 125 VDC Option) Industrial Applications
DC Power Connector: 3 terminals: “-“, “GND”, “+”
Input Voltage: 88 - 150 VDC
Power Consumption: Same as for AC models (see Section 1.1)
With the exception of the power supply, all specifications and
functions of Magnum 6K32T & 6K32TRC Switch -48VDC, 24VDC and 125VDC
models are identical to those listed in the main manual.
B2.0
-48VDC, 24VDC and 125VDC POWER, THEORY OF OPERATION
The -48VDC, 24VDC and 125VDC power options are designed using diodes
inside on each DC power input line behind the two external power connection terminals,
POWER SWITCH
so that the power from an external
HUB
SUPPLY
source can only flow into the hub.
+
-
A+
A-
FUSE
This allows the Switch to operate
only whenever DC power is
CHASSIS
GND
GND
www
.
GarrettCom . com
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
correctly applied to the two inputs. It protects the Switch from incorrect DC input
connections. An incorrect polarity connection, for example, will neither affect the
Switch, its internal power supply, nor will it blow the fuse in the internal power supply.
The manual power “On-Off” Switch (optional) is used for powering the unit on
and off when it is placed into or taken out of service.
B3.0
APPLICATIONS FOR DC POWERED SWITCHES
Magnum 6K32T & 6K32TRC Fiber Switches are easily installed in a variety of
applications where -48VDC, 24VDC and 125VDC power is used as the primary power
source. The- 48VDC, 24VDC and 125VDC power configuration provides an Ethernet
networking solution utilizing a special power supply in a Managed Switch.
The –48VDC solution is particularly useful in the telecommunication industry,
where it is common for facilities to operate on -48VDC power. Such companies include
regular and wireless telephone service providers, Internet Service Providers (ISPs) and
other communication companies. In addition, many high availability equipment services,
such as broadcasters, publishers, newspaper operations, brokerage firms and other
facilities often use a battery backup system to maintain operations in the event of a power
failure. It is also frequently used for computer system backup, management and
operations monitoring equipment.
The 24VDC and 125VDC solution are particularly useful in the Industrial
environment, where it is common facilities to operate on 24VDC or 125VDC power. The
125VDC solution is mainly used in power utilities, such as electrical substations,
electrical generating plants, etc. The 24VDC applications are mainly in the Industrial
environment, such as factory floor, HVAC equipment, military equipment, etc.
B4.0
INSTALLATION
This section describes the installation of the -48 VDC, 24VDC and 125VDC
power source leads to the -48 VDC, 24VDC and 125VDC power terminal block on the
Magnum 6K32T & 6K32TRC’s. (see figure at right).
In this picture, the -48VDC terminal block on the Magnum 6K32T &
6K32TRC is located on the rear of the unit and is equipped with three (3) screw-down
lead posts. It is similar for 24VDC and 125VDC options on Magnum 6K32T &
6K32TRC. The leads are identified as negative (-),
positive (+), and chassis ground (GND).
Figure B4.0: -48VDC Terminal Block on Magnum 6K32T & 6K32TRC-
48VDC
www
.
GarrettCom . com
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
The actual connection procedure is very straightforward. Simply connect the
leads to the Magnum unit, beginning with ground. Ensure that each lead is securely
tightened.
Note: The GND should be hooked up first. The 6K32T & 6K32TRC unit has a floating
ground, so the user may elect to Ground either + or - terminal to suit the customer’s
use.
Before connecting hot lines to the Terminal Block of –48VDC, 24VDC or
125VDC, always use a digital voltmeter to measure the output voltage of the power
supply and determine the lead which is more “+ve potential”. The more “+ve” voltage
lead from 48V or –48V supply must be connected to the post labeled “+”.
An ON-OFF manual switch is optional for DC power. This can be used to cut
off power connections and as a RESET for the Magnum 6K32T & 6K32TRC Switch.
B4.1
UL Requirements for DC-powered units
1. Minimum 18AWG cable for connection to a Centralized DC power source.
2. Minimum 14AWG cable for connection to a earthing wiring.
3. Use only with Listed 10 A circuit breaker provided in building installation.
4. “Complies with FDA radiation performance standards, 21 CFR subchapter J.”
or equivalent.
5. Fastening torque of the lugs on the terminal block: 9 inch-pound max.
6. Centralized DC Power Source cable securement, use at least Minimum 14AWG
four cable ties to secure the cable to the rac,k at least 4 inches apart, with the
first one located within 6 inches of the terminal block.
B5.0
OPERATION
Operation of Magnum 6K32T & 6K32TRC Switches with the optional -
48VDC, 24VDC and 125VDC power supply is identical to that of the standard AC-
powered models.
B6.0
ORDERING INFORMATION
To order the optional -48VDC power supply factory installed, add a suffix of “-
-48VDC” after the product’s standard model # Example: Magnum 6K32R & 6K32T &
6K32TRC -48VDC.
Similarly to order the optional 24VDC or 125VDC industrial specific power
supply factory installed, add a suffix of “ 24VDC” or “125VDC” after the product ‘s
standard model #. Example: Magnum 6K32T & 6K32TRC- 24VDC, Magnum 6K32T
& 6K32TRC-125VDC.
www
.
GarrettCom . com
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
B7.0 TROUBLESHOOTING
Please refer to Section 6.0 for troubleshooting
Installation and User Guide 05/07)
APPENDIX C: Internal DC Dual-Source Power Option
C1.0
SPECIFICATIONS - FOR MAGNUM 6K32T & 6K32TRC FIBER
SWITCH
Power Supply (Internal, -48VDC Dual-Source, model # Dual-Src-48V)
DC Power Connector: First Source: “A+”, “A-“, 2nd Source “B-“, “B+”
GND:
Terminal for “earth” or ground wire connection to the hub chassis
Input:
Two separate sources, each at 36 - 70 VDC
Power Supply (Internal, 24VDC Dual-Source, model # Dual-Src-24V)
DC Power Connector: First Source: “A+”, “A-“, 2nd Source “B-“, “B+”
GND:
Terminal for “earth” or ground wire connection to the hub chassis
Input:
Two separate sources, each at 20 - 36 VDC
Power Supply (Internal, 125VDC Dual-Source, model # Dual-Src-24V)
DC Power Connector: First Source: “A+”, “A-“, 2nd Source “B-“, “B+”
GND:
Input:
Terminal for “earth” or ground wire connection to the hub chassis
Two separate sources, each at 88 - 150 VDC
With the exception of the dual DC input power connections and the power
supply, all specifications and configuration options for the Magnum 6K32T & 6K32TRC -
48VDC, 24VDC and 125VDC models with this Dual-Source option are identical to those
listed in the Magnum 6K32T & 6K32TRC Fiber Switches Installation and User Guide,
including Appendix B “Internal DC Power Supply Option”
C2.0
125VDC Dual-Source option
The 6K32T & 6K32TRC & 6K32-Switch models with the internal -48VDC,
MAGNUM 6K32T & 6K32TRC & 6K32, with -48VDC, 24VDC and
24VDC and 125VDC Dual-Source power supply are designed for installations where a
battery plant is the power source, and where two separate power sources are utilized in
order to increase operational uptime and to simplify maintenance.
The functionality of the Magnum 6K32T & 6K32TRC Switch -48VDC,
24VDC and 125VDC Dual-Source Option units is identical to the standard AC-powered
models. Refer to the main sections of
A+
HUB
this Installation and User Guide for a
detailed description of the Magnum
6K32T & 6K32TRC Switches.
SUPPLY
A-
+
FUSE
-
B-
B+
CHASSIS
GND
GND
www
.
GarrettCom . com
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
C3.0 DUAL-SOURCE OPTION, THEORY OF OPERATION
The Dual-Source DC power option is designed using diodes inside of the
Installation and User Guide 05/07)
chassis on each DC power input line. A diode is placed in each of the four input lines
(behind the four external power connection terminals) so that power from an external
source can only flow into the unit. This allows the unit to operate whenever DC power is
correctly applied to either or both of the two inputs
C4.0
FEATURES AND BENEFITS OF THE DUAL-SOURCE DESIGN
a) The Switch unit can receive power from either input, “A” or “B”. The hub will normally draw
its power from the DC source with the highest voltage at a given time.
b) The Switch unit will not allow power to flow from a higher voltage input to a lower voltage
input, i.e. the two DC power sources are not mixed together by the hub.
c) When one correct DC input is present, the Switch will receive power if the other DC input is
absent, or even if it is connected with reverse polarity or shorted or grounded.
d) Reverse polarity connections, if they should accidentally occur on either input, will not damage
the Switch or power supply internally (nor will it blow the fuse in the internal power supply)
because of the blocking action of the diodes. This is true even if one input connection is
reversed while the Switch is operating from the other source.
e) The Switch will not receive power (and will not work) when both inputs are simultaneously
absent or are both incorrectly connected.
C5.0
INSTALLATION
This section describes the proper connection of the -48VDC, 24VDC and
125VDC dual source leads to the -48VDC, 24VDC 7 125VDC power terminal block on
the Magnum 6Ks Switch (shown in Figure )
The -48VDC terminal block on the Magnum 6K32T & 6K32TRC Switch, as shown in
Fig C5.0 is located on the right rear of
A+ A- B- B+
the unit and is equipped with five (5)
screw-down lead posts. If it is the
reverse model it is located on the left
rear. The primary terminals are
identified as positive (A+), negative
36-70VDC
36-70VDC
GND
(A-), and the secondary power
terminals as negative (B-), positive(B+). The chassis “earth” or ground (GND) is a
threaded post with a #6 nut. The Dual Source terminal block for the 24VDC and
125VDC are similar.
Figure C5.0: -48VDC Dual-Source, wiring connections to the External
Terminal Block on a Magnum 48VDC with Dual-Source option
Note: The GND should be hooked up first. The6K32T & 6K32TRC unit has a floating
ground, so the user may elect to Ground either + or - terminal to suit the customer’s
use.
Before connecting hot lines to the Terminal Block of –48VDC, 24VDC or
125VDC, always use a digital voltmeter to measure the output voltage of the power
supply and determine the lead which is more “+ve potential”. The more “+ve” voltage
www
.
GarrettCom . com
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnum 6K32T & 6K32TRC Managed Switch
Installation and User Guide 05/07)
lead from 48V or –48V supply must be connected to the post labeled “+”.
The connection procedure is straightforward. Simply connect the DC leads to
the Switch’s power terminals, positive (+) and negative (-) screws. Ensure that each lead
is securely tightened.
The 24VDC and 125VDC terminal block on Magnum 6K32T & 6K32TRC’s is
similar to that described in the –48VDC information above.
C5.1 UL Requirements
The following must be adhered to in order to conform to UL requirements:
1. Minimum 18 AWG cable for connection to a Centralized DC power source.
2. Minimum 14 AWG cable for connection to earthing wiring.
3. Use only with Listed 10 A circuit breaker provided in building installation.
4. “Complies with FDA radiation performance standards, 21 CFR subchapter J.”
or equivalent.
5. Fastening torque of the lugs on the terminal block: 9 inch pound max.
6. Centralized DC Power Source cable securement, use at least four Minimum 14
AWG cable ties to secure the cable to the rack at least 4 inches apart with the
first one located within 6 inches of the terminal block.
C6.0
ORDERING INFORMATION
To order the optional Dual-Source -48VDC power supply factory installed,
order “Dual-Src48V” as a separate line item following the product model.
Example: Magnum 6K32T & 6K32TRC-48VDC
Dual-Src-48V for the regular DS model with no ON-OFF switch
or Dual-Src48V-SWITCH with the ON-OFF manual switch.
Similarly, order the “Dual –source 24VDC” or “Dual-source 125VDC” as a
separate line item following the product model.
Example: Magnum 6K32T & 6K32TRC-24VDC or Magnum 6K32T &
6K32TRC-125VDC
Dual-Src24V for regular models with no ON-OFF switch
Or Dual-Src125V-Switch for models with the ON-OFF switch
C7.0
OPERATION
Operation of the Dual-Source Magnum 6Ks-48VDC, 24VDC and 125VDC
Switch models are identical to that of the standard models.
www
.
GarrettCom . com
73
Download from Www.Somanuals.com. All Manuals Search And Download.
|