Safety Instructions . . . . . . . . . . 2, 3
Owner’s Manual
Operating Instructions
WHSB8000
WHSB9000
Clothes Care Cycles . . . . . . . . . . .8, 9
Controls . . . . . . . . . . . . . . . . . . . .4, 6
Controls Features . . . . . . . . . . . . .10
Cycle Options . . . . . . . . . . . . . . . .11
Loading and Using
the Washer . . . . . . . . . . . . . . . .13, 14
One Touch Cycles . . . . . . . . . . . .4–7
Other Features . . . . . . . . . . . . . . .11
Washer Features . . . . . . . . . . . . .8–12
Troubleshooting Tips . . . . . . .15–18
Consumer Support
Consumer Support . . . . . . . . . . . . 20
Warranty . . . . . . . . . . . . . . . . . . . . 19
Write the model and serial
numbers here:
Model # ______________
Serial # ______________
You can find them in the
upper right corner on the
back of your washer.
175D1807P403 49-90140 04-02 JR
Download from Www.Somanuals.com. All Manuals Search And Download.
For your safety, the information in this manual must be followed to minimize the risk
of fire or explosion, electric shock, or to prevent property damage, personal injury,
or loss of life.
WARNING!
WHEN USING THE WASHER
ꢀ Never reach into washer while it is moving. Wait
until the machine has completely stopped before
opening the lid.
ꢀ
The laundry process can reduce the flame retardancy
of fabrics. To avoid such a result, carefully follow the
garment manufacturer’s wash and care instructions.
ꢀ Do not mix chlorine bleach with ammonia or acids ꢀ To minimize the possibility of electric shock, unplug
Use this
such as vinegar and/or rust remover. Mixing
different chemicals can produce a toxic gas which
may cause death.
this appliance from the power supply or disconnect
the washer at the household distribution panel by
removing the fuse or switching off the circuit
breaker before attempting any maintenance or
cleaning. NOTE: Pressing START or STOP does NOT
disconnect the appliance from the power supply.
appliance
only for its
intended
purpose as
described in
this Owner’s
Manual.
ꢀ Do not wash or dry articles that have been cleaned
in, washed in, soaked in, or spotted with combustible
or explosive substances (such as wax, oil, paint,
gasoline, degreasers, dry-cleaning solvents, kerosene, ꢀ Never attempt to operate this appliance if it is
etc.) which may ignite or explode. Do not add these
substances to the wash water. Do not use or place
these substances around your washer or dryer during
operation.
damaged, malfunctioning, partially disassembled, or
has missing or broken parts, including a damaged
cord or plug.
WHEN NOT IN USE
ꢀ Turn off water faucets to relieve pressure on hoses
and valves and to minimize leakage if a break or
rupture should occur. Check the condition of the
fill hoses; they should be replaced every 5 years.
ꢀ Do not attempt to repair or replace any part of this
appliance unless specifically recommended in this
Owner’s Manual, or in published user-repair
instructions that you understand and have the skills
to carry out.
ꢀ Before discarding a washer, or removing it from
service, remove the washer lid to prevent children
from hiding inside.
ꢀ Do not tamper with controls.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Easy ONE TOUCH Cycles.
Your new washer offers the convenience of starting your wash loads with our easy ONE TOUCH cycles. Make one simple
selection, and your LOAD SIZE, SOIL LEVEL, WASH/RINSE TEMPERATURE and WASH/SPIN SPEED are automatically set.
Then all you have to do is press START.
ONE TOUCH
Quick Start Guide
• Close lid
• Select wash cycle
• Add clothes
• Push START
• Check load size setting
• Add detergent
• Add diluted fabric
softener (on models
with a fabric softener
dispenser)
Washer control panel for Model WHSB8000.
You can locate your model number behind the top edge of the control panel.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ONE TOUCH selections for Model WHSB8000.
PRESS... AUTOMATICALLY SELECTS... THEN PRESS...
For heavy to lightly soiled cottons, household linens,
work and play clothes.
For heavy to lightly soiled cottons, household linens,
work and play clothes.
For non-colorfast cottons and blends, and items that
are labeled cold wash by the fabric manufacturer.
For knits, wrinkle-free and permanent press items.
For lingerie and items labeled hand-washable with
light soils. Provides periods of agitation and soak
during wash and rinse.
For wrinkle-free and permanent press items and
knits. Provides agitate/pause cycles to clean your
heavily soiled items.
Changing the automatic settings.
You can change any of the automatic settings simply by pressing the desired pads.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Easy ONE TOUCH Cycles.
Your new washer offers the convenience of starting your wash loads with our easy ONE TOUCH cycles. Make one simple
selection, and your LOAD SIZE, SOIL LEVEL, WASH/RINSE TEMPERATURE, WASH SPEED and SPIN SPEED are automatically
set. Then all you have to do is press START.
ONE TOUCH
Quick Start Guide
• Close lid
• Select wash cycle
• Add clothes
• Push START
• Check load size setting
• Add detergent
• Add diluted fabric
softener (on models
with a fabric softener
dispenser)
Washer control panel for Model WHSB9000.
You can locate your model number behind the top edge of the control panel.
This washer uses an advanced variable speed motor to provide you with superior clothes care and wash cycle flexibility.
The use of this motor allows your washer to agitate more slowly than a conventional washer, and to spin at speeds that
more closely meet the needs of your clothing.
Some wash cycles are pulsed, and will agitate and soak to provide you with better cleaning and less wear on your
clothing. Some spin cycles will start slowly and then accelerate, allowing more water to be removed from the clothes
with less wrinkling. These functions are a normal part of your new washer, and help to provide you with the most
versatile washer ever made by GE.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ONE TOUCH selections for Model WHSB9000.
PRESS... AUTOMATICALLY SELECTS...
THEN PRESS...
For heavy to lightly soiled cottons, household linens,
work and play clothes.
For heavy to lightly soiled cottons, household linens,
work and play clothes.
For non-colorfast cottons and blends, and items that
are labeled cold wash by the fabric manufacturer.
For knits, wrinkle-free and permanent press items.
For lingerie and items labeled hand-washable with
light soils. Provides periods of agitation and soak
during wash and rinse.
For lightly soiled items that are needed in a hurry.
Cycle time is approximately 15 minutes, depending
on your household water pressure.
Changing the automatic settings.
You can change any of the automatic settings simply by pressing the desired pads. The wash/rinse temperature can
be changed by pressing TEMP WASH/RINSE.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
About Clothes Care Cycles.
STAIN WASH (on some models)
For heavily soiled or stained items. Adds an extra agitation and soak at the beginning
of the wash cycle.
PRESOAK
To presoak a load and go straight into a wash cycle:
Select your wash cycle, press the PRESOAK pad, then press the START pad.
ꢀ Starts with three minutes of agitation, then 12 minutes of soaking, followed by the
selected wash cycle.
ꢀ Uses the speed and water temperature of your selected wash cycle.
To presoak a load without going straight into a wash cycle:
Press the PRESOAK pad. The washer will fill. You may change the automatic settings
Appearance may vary.
if desired.
ꢀ Three minutes of agitation is followed by up to 24 hours of soaking.
ꢀ To soak less than 24 hours, press the DRAIN & SPIN pad or choose a wash cycle.
QUICK RINSE (on some models)
Use this feature to quickly rinse chlorine, perspiration, stains, etc. out of clothes.
QUICK
RINSE
ꢀ The washer fills with water, agitates for three minutes, drains and spins. You may
change the automatic settings if desired.
HANG DRY (on some models)
If you air dry your clothes without the aid of a dryer, you may find that the slower final
spin speed of the Hang Dry setting produces fewer wrinkles in your clothing. This may
significantly reduce your ironing chore.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DRAIN & SPIN
DRAIN & SPIN any cycle at any time.
DRAIN
& SPIN
CUSTOM 1 and CUSTOM 2 (on some models)
CUSTOM CUSTOM
Set up your favorite combination of settings and save them here for one-touch recall.
These custom settings cannot be set while a cycle is in progress.
To store a custom combination of settings:
1
2
PRESS 3 SEC TO STORE
1. Select a ONE TOUCH setting.
2. Change LOAD SIZE, SOIL LEVEL, TEMPERATURE, WASH SPEED or SPIN SPEED to fit
your needs.
3. Select any OPTIONS you want.
4. Press and hold the CUSTOM 1 or CUSTOM 2 pad until the washer beeps to store
your selection.
To recall your stored combination:
Press the CUSTOM 1 or CUSTOM 2 pad, then press START.
NOTE: DELAY 1-8 HRS. cannot be used in CUSTOM 1 and CUSTOM 2 settings.
To reprogram the custom settings:
Repeat steps 1–4 above.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
About controls features.
START
ꢀ After you have selected a new cycle, press once to start the cycle.
ꢀ Press twice to select the last cycle used and start the washer.
ꢀ If the washer is running, press once to interrupt the cycle; press again to continue
the cycle.
STOP
This pad should not be used to interrupt or pause a cycle.
Pressing this pad will cancel the current settings and the settings will be lost.
Estimated Time Remaining
ꢀ Displays the approximate time remaining until the end of the cycle.
E
ST.
T
IME REMAINING
ꢀ If the estimated time remaining is more than 60 minutes, “1H” will flash in the
display, followed by the additional remaining minutes. When the time remaining is
less than 60 minutes, the timer will count down.
ꢀ Cycle time is affected by how long it takes the washer to fill. This depends on the
water pressure in your home. The “smart” timer “learns” the amount of time it
takes to fill your washer and adjusts the total time accordingly.
NOTE: If PRESOAK is selected and a follow up wash cycle is not chosen, two dashes
will come up in the display.
Spot Spray
Provides a short spray of water to allow you to dampen clothing when you pretreat stains.
Open the washer lid.
1
2 Press the SPOT SPRAY button. (You will see a short stream of water.)
Dampen your soiled garment with the SPOT SPRAY option and rub your favorite
3
pretreatment product into soiled area.
NOTE: The SPOT SPRAY option will not work if
ꢀ the washer lid is down
ꢀ the washer tub is filling
ꢀ the water has already reached the level you selected.
BLEACH SIGNAL (on some models)
The Bleach Signal is a reminder signal that can be turned on to remind you to add bleach at
the proper time in the wash cycle. Adding detergent and bleach at the same time reduces the
effectiveness of both the enzymes in the detergent and the chlorine in the bleach. By adding
bleach later in the wash cycle, you allow the detergent’s enzymes to remove dirt and stains first,
and then provide a more effective dose of liquid bleach to whiten and sanitize your clothes.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
About cycle options.
SIGNAL
Alerts you when the cycle is complete.
On some models, press SIGNAL to turn the beeper on or off.
Appearance may vary.
On some models, press SIGNAL to select low or high volume, or to turn the beeper off.
2ND RINSE
Adds a second rinse to any cycle.
EXTEND SPIN
Extends the last spin of a wash cycle. This will extract more water from your clothes.
Clothes will be drier when you use this option.
DELAY 1-8 HOURS (on some models)
Use to delay the start of your washer for 1 to 8 hours. First choose your wash cycle and
any options. Then press this pad for the number of hours you want to delay the cycle.
Press the START pad to start the countdown.
The countdown time will be shown in the Est. Time Remaining display.
About other features.
Cycle Status Indicator Lights
The cycle status indicator lights display what part of the cycle the washer is in.
PerfecTemp Plus
PerfecTemp Plus senses the incoming water temperature and adjusts the temperature
of the fill water.
The lid must be closed for PerfecTemp Plus to work.
If your water is too cold, detergent will not dissolve effectively and clothes may not get
clean. If the water is too hot, fabrics could be damaged.
PerfecTemp Plus adjusts these water temperature extremes for better washing
performance.
You may hear the water valves turning off and on while the water temperature is being
adjusted. This is normal.
Some models have an indicator light that tells you when PerfecTemp Plus is active.
Auto Balance (on some models)
The Auto Balance feature senses the wash load distribution for an even spin. Models
with Auto Balance have an indicator light that tells you when the feature is active.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
About washer features.
Liquid Bleach Dispenser
The dispenser dilutes liquid chlorine bleach before it reaches into your wash load.
1 Check clothing care labels for special instructions.
2 Measure liquid bleach carefully, following instructions on the bottle.
ꢀ Never pour undiluted liquid chlorine bleach directly onto clothes or into the wash basket.
ꢀ Do not pour powdered bleach into bleach dispenser.
Before starting the washer, pour measured amount of bleach directly into bleach
dispenser. Avoid splashing or over-filling dispenser. If you prefer to use powdered
bleach, add it into the wash basket with your detergent.
3
ꢀ Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing
can produce a toxic gas which may cause death.
The Agitator Cap or Fabric Softener Dispenser
Add water to dispenser until it reaches
the maximum fill line.
The agitator cap fits into the top of the
agitator. If it accidentally comes off, simply
put it back on.
3
The fabric softener dispenser automatically
releases liquid fabric softener at the proper
time during the cycle.
Do not stop the washer during the first spin.
This will cause the dispenser to empty too
soon.
To use, follow these steps:
Do not pour anything into the agitator if
the agitator cap or dispenser is removed.
Make sure dispenser is securely
attached to agitator.
1
Use only liquid fabric softener.
2
Pour into dispenser, using amount
recommended on package.
Never pour fabric softener directly on
clothes. It may stain them.
Cleaning the Fabric Softener Dispenser
1 Remove the dispenser from the top of the agitator.
Separate the dispenser cup from the cover by grasping the top and pushing down on
the inside of the cup with your fingers. Dispenser cup will pop free from the cover.
2
To clean the dispenser, soak both the dispenser cup and the dispenser cover in the
following solution:
3
ꢀ 1 US gallon (3.8 liters) warm water
ꢀ 1/4 cup (60 ml) heavy duty liquid detergent
ꢀ 1 cup (240 ml) bleach
Separate for cleaning.
If necessary, loosen build-up with a clean, soft cloth after soaking. Do not use a stiff
brush; you may roughen the surface of the dispenser.
4
5 Rinse and reassemble dispenser. Place dispenser back on the agitator.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading and using the washer.
Always follow fabric manufacturer’s care label when laundering.
Sorting Wash Loads
Sort by color (whites, lights, colors), soil level,
fabric type (sturdy cottons, easy care, delicates),
and whether the fabric produces lint (terry cloth,
chenille), or collects lint (velveteen, corduroy).
Proper Use of Detergent
Using too much detergent is a common cause
of laundry problems. Today’s detergents are
formulated to be effective without highly visible
sudsing. Be sure to carefully read and follow
manufacturer’s recommendations for how
much detergent to use in your wash.
You can use less detergent if you have soft water,
a smaller load or a lightly soiled load.
Loading the Washer
Load dry items loosely, no higher than
the top row of holes in the washer basket.
When loading wet items make sure you set
the load/water level high enough to allow
the items to move freely. Water level should
just cover the clothes. To add items after
washer has started, lift the lid and submerge
additional items next to the agitator.
ꢀ Do not wrap long items like sheets or pants
around the agitator.
ꢀ Do not wash fabrics containing flammable
materials (waxes, cleaning fluids, etc.).
ꢀ Agitation will not start with the lid up.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading and using the washer.
Always follow fabric manufacturer’s care label when laundering.
Care and Cleaning of the Washer
Wash Basket: Leave the lid open after washing to
allow moisture to evaporate. If you want to clean
the basket, use a clean soft cloth dampened with
liquid detergent, then rinse. (Do not use harsh
or gritty cleaners.)
Moving and Storage: Ask the service technician to
remove water from drain pump and hoses. See the
Installation Instructions packed with product for
information on how to reinstall the shipping rod to
keep the tub stationary when moving the washer.
For more information in the United States, visit
(800.432.2737). In Canada, write to Manager,
Consumer Relations, Camco Inc., 1 Factory Lane,
Suite 310, Moncton, N.B. E1C 9M3. Do not store
the washer where it will be exposed to the weather.
Fill Hoses: Hoses connecting washer to faucet
should be replaced every 5 years.
Lint Filter: The lint filter is located under the agitator.
It is self-cleaning and requires no maintenance.
Exterior: Immediately wipe off any spills. Wipe with
damp cloth. Try not to hit surface with sharp objects.
Long Vacations: Be sure water supply is shut off at
faucets. Drain all water from hoses if weather will
be below freezing.
Fabric Care Labels
Below are fabric care label “symbols” that affect the clothing you will be laundering.
WASH LABELS
Machine
wash
cycle
Normal
Permanent Press/
wrinkle resistant
Do not wash
Do not wring
Gentle/
delicate
Hand wash
Water
temperature
Hot
(50°C/120°F)
Warm
(40°C/105°F)
Cold/cool
(30°C/85°F)
DRY LABELS
Tumble
dry
Do not dry
(used with
do not wash)
Dry
Normal
Permanent Press/
wrinkle resistant
Gentle/
delicate
Do not tumble dry
Heat
setting
High
Medium
Low
No heat/air
Special
instructions
Dry flat
Line dry/
hang to dry
In the shade
Drip dry
BLEACH LABELS
Bleach
symbols
Any bleach
(when needed)
Do not bleach
Only non-chlorine bleach
(when needed)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…
Troubleshooting Tips
Save time and money! Review the charts on the following pages,
or visit GEAppliances.com. You may not need to call for service.
PERFECTEMP PLUS
Possible Causes
What To Do
PerfecTemp Plus wash
temperature is incorrect
The washer is in a cold rinse cycle • This is normal. The PerfecTemp Plus feature is designed
not to activate during a cold rinse cycle to improve the
energy efficiency of your washer.
(Review PerfecTemp
All the water in the household
• Wait until the water in the water heater is heated to the
correct temperature.
Plus in the About washer water heater has been used
features section)
PERFORMANCE
Clothes too wet
Possible Causes
What To Do
Incorrect spin speed
selected
• Make sure the spin cycle selected matches the load you
are washing. Some fabrics will feel wetter when rinsed
with cold water.
Colored spots
Incorrect use of fabric
softener
• Check fabric softener package for instructions and follow
directions for using dispenser.
• Pretreat stain and rewash.
Dye transfer
• Sort whites or lightly colored items from dark colors.
Grayed or yellowed
clothes
Not enough detergent
• Use more detergent (especially with larger loads).
Be sure to follow detergent manufacturer’s directions.
Hard water
• Use a water conditioner like Calgon brand or install
a water softener.
Water is not hot enough
Washer is overloaded
• Make sure water heater is delivering water at
120°F–140°F (48°C–60°C).
• Select load size to match clothes load.
Detergent is not
dissolving
• Add detergent as wash basket fills with water before
you load clothes.
Dye transfer
• Sort clothes by color. If fabric label states wash separately,
unstable dyes may be indicated.
Lint or residue on
clothes
Clothes are air or line dried
• If you do not dry your clothes with a clothes dryer, your
clothes may retain more lint.
Incorrect sorting
• Separate lint producers from lint collectors.
Washing too long
• Wash small loads for a shorter time than larger loads.
Detergent not dissolving
• Add detergent as wash basket fills with water, before you
load clothes.
• Try a liquid detergent.
• Use warmer water temperature.
Overloading
• Load clothes no higher than the top row of holes in the
washer tub.
• Make sure load size selected matches clothes load size.
Incorrect use of fabric softener
• Check fabric softener package for instructions and follow
directions for using dispenser.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…
PERFORMANCE (cont.)
Pilling
Possible Causes
What To Do
Result of normal wear on
poly-cotton blends and
fuzzy fabrics
• While this is not caused by the washer, you can slow the
pilling process by washing garments inside out.
Snags, holes, tears, rips
or excessive wear
Pins, snaps, hooks, sharp
buttons, belt buckles,
zippers and sharp objects
left in pockets
• Fasten snaps, hooks, buttons and zippers.
• Remove loose items like pins, objects in pockets
and sharp buttons.
• Turn knits (which snag easily) inside out.
Undiluted chlorine bleach
• Check bleach package instructions for proper amount.
• Never add undiluted bleach to wash or allow clothes
to come in contact with undiluted bleach.
Chemicals like hair bleach
or dye, permanent wave
solution
• Rinse items that may have chemicals on them before
washing.
Wrinkling
Improper sorting
• Avoid mixing heavy items (like work clothes) with
light items (like blouses).
• Try a fabric softener.
Overloading or
incorrect water level
• Load your washer so clothes have enough room
to move freely.
Incorrect wash and
dry cycles
• Match Cycle selection to the type of fabric you are
washing (especially for easy care loads).
Repeated washing in
water that is too hot
• Wash in warm or cold water.
OPERATION
Possible Causes
What To Do
Washer pauses in cycle
The HAND WASH or CASUALS
cycle was chosen
• This is normal. The washer alternates between agitate
and soak during the HAND WASH and CASUALS cycles
to get your clothes cleaner with less wear.
Washer won’t operate
Washer is unplugged
• Make sure cord is plugged securely into a working outlet.
• Turn both hot and cold faucets fully on.
• Check controls.
Water supply is turned off
Controls are not set properly
Lid is open–safety feature
prevents agitation and spinning
when lid is up
• Close lid and reset cycle, to the beginning if necessary.
Circuit breaker/fuse is
tripped/blown
• Check house circuit breakers/fuses. Replace fuses or
reset breaker. Washer should have separate outlet.
Electronics need to be reset
• Unplug washer, wait 2 minutes, plug back in, and press
START.
START was not pressed
• Press START.
Extremely low water pressure
• Press START again.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER
Too many suds
Possible Causes
What To Do
Type of detergent
• Switch to a lower sudsing detergent brand and follow
instructions on package.
Very soft water
• Try less detergent.
Too much detergent
• Measure your detergent carefully. Use less soap if you
have soft water, a smaller load or a lightly soiled load.
Water leaks
Fill hoses or drain hose is
improperly connected
• Make sure hose connections are tight at faucets
and at washer.
• Make sure end of drain hose is properly connected
to washer and correctly inserted in and secured to
drain facility.
Household drain may
be clogged
• Check household plumbing. You may need to call a
plumber.
Constant water pressure
to the fill hoses at the
water source
• Tighten hoses at the faucets and turn the water off after
each use.
• Check condition of the fill hoses; they should be
replaced every 5 years.
Using too much detergent
in washer
• Use less detergent. Use less soap if you have soft water,
a smaller load or a lightly soiled load.
Water temperature
is incorrect
Control is not set properly
• Check water temperature control and adjust.
Water supply is turned off
or improperly connected
• Turn both hot and cold faucets fully on and make sure
hoses are connected to correct faucets.
Water valve screens are
stopped up
•
Turn off the water source and disconnect water fill
hoses from the upper back of the washer. Use a brush or
toothpick to clean the screens in the machine. Reconnect
the hoses and turn the water back on.
House water heater is
not set properly
• Make sure house water heater is delivering water
at 120°F–140°F (48°C–60°C).
PerfecTemp Plus feature
• The lid must be closed for PerfecTemp Plus to work.
• Reset cycle.
was not activated
Water pumped out
before cycle is
complete
Lid lifted or cycle was put in
pause for over 24 hours
Water won’t drain
Drain hose is kinked or
improperly connected
• Straighten drain hose and make sure washer is not sitting
on it.
• Top of drain outlet should be less than 8 ft (2.5 m)
above floor.
Water spraying during
spin cycle
Washer in spin cycle
• Spray rinse during a spin cycle is normal.
Washer did not fill
to chosen level
(PerfecTemp Plus
and START lights
are flashing)
Extremely low water pressure
Inlet hoses are kinked
• Press the START button again.
• Straighten hoses.
Water valve screens are
stopped up
•
Turn off the water source and disconnect water fill
hoses from the upper back of the washer. Use a brush or
toothpick to clean the screens in the machine. Reconnect
the hoses and turn the water back on.
Water fills and drains
at the same time
Drain stand pipe is too low
• Drain stand pipe must be above 30″ (76.2 cm).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…
NOISE
Washer is noisy
Possible Causes
What To Do
Washer is uneven
• To level the front of the washer, adjust the front leveling
legs by rotating the individual leg in the proper direction
for up or down. To level back of washer, lift back of
machine 4″ (11 cm) and set down.
Washer load is
unbalanced
• Press START to pause the washer, open the lid and
redistribute the load evenly. Close the lid and press
START again.
Shipping rod is still assembled
in unit
• To remove shipping rod from washer, pull yellow tag and
attached rod from the bottom right hand side of washer.
Washer is sitting too close
to wall (causes knocking
during cycle)
• Pull washer away from the wall; about 4″ (11 cm)
is needed.
PerfecTemp Plus feature
is being used
• This is normal. PerfecTemp Plus turns water valves off
and on to adjust water temperature.
OTHER
Possible Causes
What To Do
Labels on the exterior
of the washer will not
peel off cleanly
Occasionally the adhesive
used on the labels does
not release cleanly
• Use a hair dryer set at the lowest heat setting, directing
the air at the label for a short amount of time. This will
release the adhesive easily, without damaging the surface
of the washer.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
GE Washer Warranty.
All warranty service provided by our Factory Service Centers, or an
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
authorized Customer Care® technician. To schedule service, on-line, 24
(800.432.2737) in the United States. In Canada, call 1.800.361.3400.
For The Period Of: We Will Replace:
One Year
From the date of the
original purchase
Any part of the washer which fails due to a defect in materials or workmanship. During this full
one-year warranty, GE will also provide, free of charge, all labor and related service costs to replace
the defective part.
Two Years
From the date of the
original purchase
Any part of the washer which fails due to a defect in materials or workmanship. During this additional
one-year limited warranty, you will be responsible for any labor or related service costs.
Five Years
From the date of the
original purchase
The suspension rod and spring assembly, and main electronic control board, if any of these parts
should fail due to a defect in materials or workmanship. GE will also replace the washer lid or
cover, if they should rust under operating conditions. During this additional four-year limited
warranty, you will be responsible for any labor or related service costs.
Ten Years
From the date of the
original purchase
The transmission and outer washer tub, if any of these parts should fail due to a defect in materials
or workmanship. During this additional nine-year limited warranty, you will be responsible for any
labor or related service costs.
Lifetime
From the date of the
original purchase
The washer basket, if it should fail due to a defect in materials or workmanship. During this lifetime
limited warranty, you will be responsible for any labor or related service costs.
What Is Not Covered (for customers in the United States):
ꢀ Service trips to your home to teach you how to use
the product.
ꢀ Replacement of house fuses or resetting of circuit
breakers.
ꢀ Improper installation.
ꢀ Damage to the product caused by accident, fire, floods or
acts of God.
ꢀ Failure of the product if it is abused, misused, or used for
other than the intended purpose or used commercially.
ꢀ Incidental or consequential damage caused by possible
defects with this appliance.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. In Alaska, the
warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or
your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
What Is Not Covered (for customers in Canada):
ꢀ Service trips to your home to teach you how to use
the product.
ꢀReplacement of house fuses or resetting of circuit
breakers.
ꢀ
Damage to finish not reported within 48 hours
following delivery of the appliance.
ꢀ Failure of the product if it is misused, or used
for other than the intended purpose or used
commercially.
ꢀ Improper installation.
ꢀ
Damage to product caused by accident, fire, floods
or acts of God.
If you have an installation problem, contact your
dealer or installer. You are responsible for providing
adequate electrical, exhausting and other connecting
facilities.
WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES.
Warrantor: CAMCO INC.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Support.
GE Appliances Website
In the U.S.: www.GEAppliances.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts™” your questions,
and so much more... In Canada: www.geappliances.ca
Schedule Service
In the U.S.: www.GEAppliances.com
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at your
convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal business hours.
In Canada, call 1.800.361.3400
Real Life Design Studio
In the U.S.: www.GEAppliances.com
GE supports the Universal Design concept—products, services and environments that can be used by people of all
ages, sizes and capabilities. We recognize the need to design for a wide range of physical and mental abilities and
impairments. For details of GE’s Universal Design applications, including kitchen design ideas for people with
disabilities, check out our Website today. For the hearing impaired, please call 800.TDD.GEAC (800.833.4322).
In Canada, contact: Manager, Consumer Relations, Camco, Inc.
Suite 310, 1 Factory Lane
Moncton, N.B. E1C 9M3
Extended Warranties
In the U.S.: www.GEAppliances.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty is still
in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours. GE Consumer
Home Services will still be there after your warranty expires. In Canada, call 1.888.261.2133
Parts and Accessories
In the U.S.: www.GEAppliances.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or by phone at
800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally should be
referred to qualified service personnel. Caution must be exercised, since improper servicing may cause unsafe operation.
Customers in Canada should consult the yellow pages for the nearest Camco service center, or call 1.888.261.3055.
Contact Us
In the U.S.: www.GEAppliances.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Suite 310, 1 Factory Lane
Moncton, N.B. E1C 9M3
Register Your Appliance
In the U.S.: www.GEAppliances.com
Register your new appliance on-line–at your convenience! Timely product registration will allow for enhanced
communication and prompt service under the terms of your warranty, should the need arise. You may also mail
in the pre-printed registration card included in the packing material. In Canada: www.geappliances.ca
Printed in the United States
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|