VHF RADIOTELEPHONE
FM-8800D/8800S
PRINTED IN JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
The paper used in this manual
is elemental chlorine free.
FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya 662-8580, JAPAN
Telephone : 0798-65-2111
Fax
0798-65-4200
:
FIRST EDITION : SEP. 2004
Printed in Japan
All rights reserved.
E
: JUN. 15, 2006
Pub. No. IME-56420-E
*00014993204*
*00014993204*
* 0 0 0 1 4 9 9 3 2 0 4 *
( TATA )
FM-8800D/S
*IME56420E00*
*IME56420E00*
* I M E 5 6 4 2 0 E 0 0 *
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
CAUTION
WARNING
Attach securely protective
earth to the ship's body.
Hazardous voltage.
Can shock, burn or cause
serious injury.
The protective earth
(grounding) is required to the
AC/DC power supply unit to
prevent electrical shock.
Do not work inside the equip-
ment unless totally familiar
with electrical circuits.
Confirm that the power supply voltage
is compatible with the voltage rating
of the equipment.
Do not approach the antenna
closer than 0.9 m (MPE by
FCC) when it is transmitting.
Connection to the wrong power supply
can cause fire or equipment damage.
The voltage rating appears on the label
at the rear of the display unit.
The antenna emits radio waves
which can be harmful to the
human body.
RF power density
on antenna aperture
Description
required by
Distance
Observe the compass safe distance to
prevent deviation of a magnetic
compass.
100 W/m2
10 W/m2
2 W/m2
100 W/m2
10 W/m2
2 W/m2
0.11 m IEC 60945
FM-8800S
FM-8800D
0.33 m
IEC 60945
MPE by FCC
0.9 m
Standard
compass
Steering
compass
IEC 60945
0.11 m
0.33 m IEC 60945
MPE by FCC
FM-8800S
FM-8800D
0.90 m
0.95 m
1.45 m
1.45 m
0.9 m
(MPE: Minimum Permissible Exposure)
IF-8810
IF-8820
HS-2003
HS-8800
0.55 m
0.50 m
0.95 m
0.30 m
0.85 m
0.75 m
1.50 m
0.40 m
Turn off the power at the mains switch-
board before beginning the installation.
Post a warning sign near the switch-
board to indicate that power should not
be applied while the equipment is being
installed.
RB-8800
(W/HS-8800)
1.20 m
0.80 m
RB-8810
(W/HS-8800)
1.00 m
0.60 m
1.50 m
0.90 m
Electrical shock, serious injury or fire can
result if the power is not turned off or is
applied while the equipment is being
installed.
PR-240-CE
i
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SYSTEM CONFIGURATION................................................................................ iii
EQUIPMENT LISTS ........................................................................................... iv
1. MOUNTING ...................................................................................................1-1
2. CONNECTIONS ............................................................................................2-1
3. ASSEMBLING CONSOLE KIT .....................................................................3-1
PACKING LISTS ............................................................................................... A-1
OUTLINE DRAWINGS...................................................................................... D-1
INTERCONNECTION DIAGRAMS....................................................................S-1
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM CONFIGURATION
VHF
CH 70 RX
Antenna Antenna
VHF console
RC-8800
MAX
2 sets
Wing handset
T/R AF output for VDR
IEC61162-1 input
Junction
Box*
DSC information output
Handset
HS-2003
IF-8810
External alarm
Transceiver Unit
MAX
4 sets
Remote station
RB-8800/8810
FM-8800D
FM-8800S
DMC I/F
IF-8820
RB-8800/8810
Printer
IF+UTP-80FK
Distress Message Controller
DMC-5
Printer
PP-510
Omit for Russian Version
PP-8800
100-115/200-230 VAC
50/60 Hz, 1φ
Radio Battery
24 VDC
AC/DC
Power Supply
Unit
External
Speaker
SEM-21Q
PR-240-CE
: Standard
: Optional
24 VDC
Category of units
Unit
Antenna
All other units
Category
*: Option for FM-8800S/D-N
Exposed to weather
Protected from weather
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
EQUIPMENT LISTS
Standard Supply
Name
Type
Qty
Code No.
Remarks
D: Duplex
S: Simplex
E: With handset
HS-2003
F: With microphone
DM-2003-F
A: With IF-8810
N: No IF-8810
R: Russian version
FM-8800D-E-A
FM-8800D-E-N
FM-8800D-F-A
FM-8800D-F-N
FM-8800S-E-A
FM-8800S-E-N
FM-8800S-F-A
FM-8800S-F-N
FM-8800S-R-A
FM-8800S-R-N
1 Transceiver Unit
1
—
For E-type
Handset HS-2003,
Hanger FP05-05510,
Others FP05-05511
For F-type
FP05-05700
000-054-228
2 Accessories*
1
FP05-05710
IF-8810
000-054-156
—
Microphone DM-2003-F
For A-type
3
4
Junction Box
Installation
Materials*
1
1
1
Power cable 05S9371,
CP05-09901
CP05-09900
SP05-05501
000-054-227
005-377-820
5 Spare Parts*
Standard Supply for VHF Console
Name
Type
Qty
Code No.
Remarks
1
VHF Console
RC-8800-SN
RC-8800-DN
RC-8800-SA
RC-8800-DA
1
—
D: Duplex FM-8800D
S: Simplex DM-8800S
N: No printer
A: With printer & I/F board
Installation
Masteries*
2
3
CP05-10201
1
005-371-850
Handset HS-2003 &
Accessories*
FP05-05800
SP05-05501
1
1
000-054-372
005-377-820
Handset hanger FP05-05510
5 Spare Parts*
*: See lists at the end of this manual.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
EQUIPMENT LISTS
Optional Equipment
Name
Type
Code No.
Remarks
OP05-102
000-054-120
Flush Mount Kit
Junction Box
DMC Interface
W/ Screw 5x20 4 pcs.
IF-8810
IF-8820
—
—
No use for Russian version
RB-8800-15
(W/ 1.5 m Cable)
RB-8800-20
(W/ 2 m Cable)
RB-8810-15
(W/ 1.5 m Cable)
RB-8810-20
·FP05-05701*,
·Handset HS-8800,
·Hanger W/DIST. button HG-8800
—
—
Remote Station
·FP05-05511*,
·Handset HS-8800,
·Hanger HG-8810
(W/ 2 m Cable)
W/ 1.5 m Cable
W/ 2 m Cable
HS-8800-15
HS-8800-20
HS-8800-W-35
HS-2003-15
HS-2003-20
HS-2003-50S
HS-6000FZ11
HG-8800
000-054-230
000-054-171
000-054-287
000-054-223
000-XXX-XXX
000-XXX-XXX
000-135-072
000-054-229
000-054-231
005-951-790
000-580-019
000-144-917
Waterproof
W/ Cable 1.5 m
W/ Cable 2.0 m
W/ Straight cable 5.0 m
Handset
For HS-8800
For HS-8800
For HS-2003
For HS-6000FZ11
HG-8810
Handset Hanger
FP05-05510
AP-102
Loudspeaker
SEM-21Q
Handset HS-6000FZ5,
Receptacle RDB-VHF(B),
Hanger AP-102
Handset HS-6000FZ6,
Receptacle RDB-VHF,
Hanger AP-102
Handset HS-6000FZ11,
Receptacle RDB-VHF(B),
Hanger AP-102
Dynamic Mic. Set
OP05-57
OP05-58
OP05-42
000-045-775
000-045-776
000-045-778
Carbon Mic. Set
Handset set
Mic. Receptacle Box
Microphone
RBD-VHF (B)
DM-2003-F
PP-510
000-056-094
005-377-760
Printer
—
—
—
Printer Interface
AC-DC Power Supply
IF-8500
PR-240-CE
Whip antenna FAB-151D,
Mounting plate 4-310071,
Coax. Cable 5D-2V 10m,
Connector M-P-5 2 PCS
Whip antenna RA106,
Mounting plate RA115,
Coax. Cable 05S9104 5m
Whip antenna 396-1,
AP05-00800
000-057-721
AP05-00810
AP05-00900
000-057-722
000-057-739
000-054-123
Antenna Material
Mounting plate 4187
Whip antenna FAB-151D,
Mounting plate 4-310071,
Connector M-P-7 2 PCS
AP05-01000
*: See lists at the end of this manual
v
Download from Www.Somanuals.com. All Manuals Search And Download.
EQUIPMENT LISTS
Remarks
Name
Type
Code No.
Whip antenna 150M-W2VN,
Coax. Cable 5D-2V 10m,
Connector M-P-5 2 PCS
Whip antenna FAB-151D,
Mounting plate 4-310071,
Coax. Cable 5D-2V 10m,
Connector M-P-5 & M-P-7
Whip antenna FAB-151D,
Mounting plate 4-310071,
Coax. Cable 5D-2V 20m,
Connector M-P-5 & M-P-7
AP05-01100
000-054-224
AP05-01200
AP05-01210
000-054-232
000-054-233
Antenna Material
05S0309 *10M*
05S0309 *20M*
05S0309 *30M*
05S0309 *40M*
05S0309 *50M*
10m
000-106-043
000-106-044
000-106-046
000-106-047
000-106-048
000-111-680
000-120-792
000-120-793
000-120-794
000-120-214
000-054-125
000-054-126
-
20m
30m
Signal Cable
40m
50m
5m
10m
CO-SPEVV-SB-C
0.2x2P
15m
Twisted Cable
VHF Console Kit
20m
30m
Without Printer
With Printer
RC-8800-N-75BG
RC-8800-A-75BG
PP-8800
W/ power cable
For rack console, cable attached
Printer
Emergency lamp
EMG-1T
000-138-378
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
1. MOUNTING
Transceiver Unit
General mounting considerations
Determine the mounting location for the transceiver unit considering operator convenience,
proximity to the power source and the ground location. Keep these and the following points
in mind when selecting a mounting location.
• Locate the unit in a place free of water spray and water splash.
• Keep the unit out of direct sunlight because of heat that can build up inside the unit.
• Leave a little slack in cables to allow a service technician to move the radio from its usual
location with the cables connected. This lets him make tuning and other adjustments on a
“live” set.
• Do not install the unit where flammable gases are stored.
• Select a well-ventilated area.
• Ensure the mounting location is strong enough to support the weight of the unit (approx. 6
kg) under the condition of continued vibration normally encountered aboard the vessel. If
necessary, reinforce the mounting area with a doubling plate or lining block.
• Leave sufficient space at the sides and rear of the unit for maintenance and service
purposes and to provide for circulation of cooling air. See outlines drawings at the back of
this manual.
• For flush mounting, select a location where the LCD can be easily viewed.
• The transceiver unit will affect a magnetic compass if placed too near the compass.
Observe the compass safe distance to prevent deviation of a magnetic compass,
referring to page “ i ”.
Note: Take great care not to press the DISTRESS switch during the installation. If you
accidentally press the switch, immediately turn off the equipment and contact
appropriate authority by telephone.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
1. MOUNTING
Overview of mounting methods
Keep pressed for
4
s
in case of DISTRESS.
The alert is transmitted with steady lighting.
TEST
DEF
DISTRESS
1
4
7
2
5
8
0
3
CH16
FILE
MENU
ENT
ABC
IntCom
GHI
ACK
JKL
6PMRNIONT
INTL
USA
CANCEL
ALM STOP
SCAN
TUV
DW
9WXYZ
PQRS
CALL
MSG
Keep pressed for
4
s
in case of DISTRESS.
SHIFT
#
LOG
HI/L0
The alert is transmitted with steady lighting.
TEST
DEF
DISTRESS
1
4
7
2
5
8
0
3
CH16
FILE
MENU
ENT
ABC
IntCom
GHI
ACK
JKL
6PMRNIONT
INTL
USA
CANCEL
ALM STOP
SCAN
TUV
DW
9WXYZ
PQRS
CALL
MSG
SHIFT
#
LOG
HI/L0
Overhead
Tabletop
Keep pressed for
4
s
in case of DISTRESS.
The alert is transmitted with steady lighting.
TEST
DEF
DISTRESS
1
4
7
2
5
8
0
3
CH16
FILE
MENU
ENT
ABC
IntCom
GHI
6PMRNOINT
ACK
JKL
INTL
USA
CANCEL
ALM STOP
SCAN
TUV
DW
9WXYZ
PQRS
CALL
MSG
SHIFT
LOG
#
HI/L0
Flush Mount
Bulkhead
Overview of mounting methods
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
1. MOUNTING
Mounting procedure for tabletop, overhead and bulkhead mounting
1. Using the hanger as a template, mark fixing holes in the mounting location.
2. Fix the hanger to the mounting location with self-tapping screws and washers (supplied).
(For added support, use nuts, bolts and washers instead of self-tapping screws.)
3. Screw the knob bolts with washers into the transceiver unit.
4. Set the transceiver unit to the hanger and tighten knob bolts.
265
251
Keep pressed for
4
s
in case of DISTRESS.
The alert is transmitted with steady lighting.
TEST
DEF
DISTRESS
1
4
7
2
5
8
0
3
CH16
FILE
MENU
ENT
ABC
IntCom
GHI
ACK
JKL
6PMRNIONT
A
LARM
110
INTL
USA
CANCEL
ALM STOP
SCAN
TUV
DW
9WXYZ
PQRS
H
A
N
D
SET
V
O
L/PW
R
SQL
CH
CALL
MSG
SHIFT
#
LOG
HI/L0
O
FF
A
U
TO
ＰＵＳＨＴＯＥＮＴＥＲ
Keep pressed for
4
s
in case of DISTRESS.
The alert is transmitted with steady lighting.
TEST
DEF
DISTRESS
1
4
7
2
5
8
0
3
CH16
FILE
MENU
ENT
ABC
IntCom
GHI
ACK
JKL
6PMRNIONT
A
LARM
INTL
USA
CANCEL
ALM STOP
SCAN
TUV
DW
9WXYZ
PQRS
100
100
H
A
N
D
SET
V
O
L/PW
R
SQL
CH
CALL
MSG
SHIFT
#
LOG
HI/L0
O
FF
A
U
TO
ＰＵＳＨＴＯＥＮＴＥＲ
• All dimensions in millimeters.
• Leave sufficient space at the sides and rear of the unit to provide easy access for
maintenance and service.
Mounting dimensions for tabletop, overhead and bulkhead mounting
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
1. MOUNTING
Mounting procedure for flush mount (option)
Requires optional flush mount kit OP05-102 (Code No. 000-054-120). Prepare a cutout in
the mounting location whose dimensions are as shown in the figure below.
Flush mount kit OP05-102
Name
1 Mounting plate
2 Self-tapping screw
3 Hex screw
Type
Code No.
Qty
1
4
05-093-1211 100-323-160
5x20
M8x16
000-802-081
000-882-075
2
#150
20
14
251
27
244
±
±
260
280
1
1
±
277 0.5
Pilot holes (4 pcs.)
Mounting dimensions for flush mount
VHF Antenna
The antenna requirements
Any good quality antenna meeting the requirements shown below may be used. A high-gain
antenna is preferable.
•
•
•
•
•
Frequency range:
Impedance:
155 to 164 MHz
50 ohms
Polarization:
Handling power:
Quality:
Vertical
30 W/ min
Able to withstand marine environment
Mounting considerations
•
The antenna should be well separated from nearby antennas, masts, and other interfering
objects.
•
The higher the antenna is mounted above the horizon, the further the communications
range.
Mounting procedure
The basic mounting procedure for antennas supplied by FURUNO is as follows, however
consult appropriate outline drawing for details.
1. Fasten the antenna bracket to the stanchion.
2. Set the antenna to the antenna bracket and tighten bolts.
3. Screw the coaxial cable plug into the antenna.
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. MOUNTING
CH70 RX Antenna
The antenna should be well separated from nearby antennas, masts, and other interfering
objects.
The mounting procedure is the same as that for the VHF antenna, however consult
appropriate outline drawing for details.
Handset Hanger
The handset hanger can be mounted at the left side of the transceiver unit. The mounting
location should provide easy access to front panel controls while operating the handset.
Also, the length of the standard handset cable is 50 cm, so locate the handset hanger within
50 cm of the unit. (Longer cables are available optionally.)
Power Supply (option)
For Convention vessels, both AC and DC power must be fed to the FM-8800D/8800S, via
an AC/DC power supply. When AC input fails, DC power is supplied. FURUNO can supply
an AC/DC power supply unit, the PR-240-CE.
Mounting considerations
When selecting a mounting location, keep in mind the following points.
• Select a location which provides adequate ventilation.
• The location must be clean and dry.
• The mounting location must be able to support the weight of the unit (14.5 kg) under the
continued conditions of vibration normally encountered aboard the vessel. If necessary,
reinforce the mounting location.
• The PR-240-CE will affect a magnetic compass if it is placed to near the compass.
Observe the compass safe distance to prevent deviation of a magnetic compass,
referring to page “ i ”.
Mounting
Refer to outline drawing.
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
1. MOUNTING
Printer (option)
Printer PP-510
To mount the printer, refer to the printer outline drawing at the back of this manual.
1. Select a flat surface.
2. Fix the mounting base to the mounting location with four screws (supplied).
3. Lay the printer on the top of the mounting base and fasten it with the mounting fixtures
(two at each side and one at rear).
Mounting Fixture
Mounting Fixture
Mounting Dimensions 300 (H) x 396 (W) mm
Mounting of Printer PP-510
Printer PP-8800
The printer PP-8800 is flush-mounted in a panel. Refer to the outline drawing at the back of
this manual.
1. Make a cutout of 208(w) x 118(h) mm.
2. Set the printer and fix it with four self-tapping screws (4x16).
Printer Interface (option)
The printer interface IF-8500 is required for the printer PP-510 which is commonly used with
the FM-8800D/S and other MF/HF radio communication equipment. To mount the unit, see
the outline drawing at the back of this manual.
External Loudspeaker (option)
The external loudspeaker can be installed on a tabletop, the overhead or a bulkhead.
Fasten the loudspeaker to the mounting location with self-tapping screws, or nuts, bolts and
washers. For mounting dimensions, see the outline drawing at the back of this manual.
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. MOUNTING
Junction box IF-8810/ DMC interface IF-8820
Note: DMC interface IF-8820 is not used for Russian version.
To install the remote box RB-8800/RB-8810, wing handset, etc., the junction box IF-8810 is
required. Install the junction box near the transceiver unit. Approx. 3 m cable is preattached
to the junction box to connect to the transceiver unit.
To connect Furuno’s distress message controller DMC-5, the DMC interface IF-8820
(option) is required.
1. Open the cover.
2. Mount the unit with four self-tapping screws (5x20).
240
Note: This plug is not
fitted in IF-8820.
100
Fixing holes 5mm dia.
Mounting the junction box/DMC interface
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. MOUNTING
Remote station RB-8800/RB-8810 (option)
Up to four remote stations can be connected in a daisy chain.
Note: For the remote station RB-8800, there are two method of cable entry: bottom-side entry
and rear-side entry. For rear-side entry, make one or two holes of more than 12 mm diameter.
For last station in the daisy chain, just one cable entry hole is needed.
1. Remove screws on the handset hanger (four for RB-8800, six for RB-8810).
2. Remove upper chassis of the hanger.
3. Mount the base of the hanger to a bulkhead with self-tapping screws 4x20 (four for
RB-8800), or 4x16 (two for RB-8810).
4. After connecting cables, assemble the remote station.
5. For RB-8800, attach blind seals on the screws.
77
Handset
HS-8800
Screws 4 pcs.
Attach blind seal
on the screws.
20 30
Cover of handset hanger
Nameplate
Handset hanger
HG-8800
DISTRESS
Cable entry
(Rear)
VOLUME
φ
4- 4.5
Fixing holes
±
±
40 0.5 40 0.5
Cable entry
(Bottom)
Remote station RB-8800
Hanger
HG-8810
Handset
HS-8800
(77)
57
Cable entry
65
Nameplate
φ
2- 4.5
Fixing hole
Hanger
Hanger mounting base
Remote station RB-8810
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
1. MOUNTING
Outdoor mounting of RB-8810
Remote station RB-8810 with waterproof-type handset HS-8800-W-35 can be mounted
outdoors. The hanger should be coated as directed below with silicone sealant for
waterproofness.
1. Fix the mounting base with self-tapping screws. Coat exposed part of these screws with
silicone sealant.
2. Attach the cable from the transceiver unit or junction box. Coat cable around cable
entrance with silicone sealant
3. Fix the cover of the handset hanger. Coat junction between mounting base and cover
with silicone sealant.
2. All around the cable
at cable entry
Self-tapping screws
3. All around the junction
coating parts
Note: Confirm that plastic washers are
in screw holes before fixing cover.
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
1. MOUNTING
VHF console
Install the rack console where the equipment can be easily operated, checked and serviced.
Consult with shipyard personnel and ship's officer-in-charge to determine best location. The
location must satisfy the following points:
• Select a location where controls can be easily operated.
• Select a location where shock and vibration are minimal.
• Locate the console away from water splash and rain.
• The temperature and humidity of the location should be both stable and moderate.
Fixing
1. Ask shipyard personnel to tighten six M5 nuts or six M5 bolts to the fixing holes (on the
wall), referring to the outline drawing at the back of this manual.
2. Detach the cover assembly from the console.
3. Hang VHF console on bolts.
4. Screw the console with the bolts or nuts tightly.
5. Attach the cover assembly to the console.
Note: When you connect wires as soon as attaching console, refer to paragragh 2-10.
6. Attach the handset hanger with two screws.
7. To attach the optional emergency lamp, connect the cable to the terminal board, and
then attach the lamp to the console. Refer to the interconnection diagram and out line
drawing.
EMG-1T
EMERGENCY LAMP
190
(371)
(371)
330
75
°
40
HANDSET HANGER
30
CABLE ENTRY
TERMINAL BOARD
(REAR)
250
FIXING HOLES
(266)
298
±
0.5
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONNECTIONS
Overview
The figure below shows where to connect various equipment at the rear of the transceiver
unit.
ANT
Ground terminal.
Connects antenna.
24VDC
Connects power
cable.
CH70 RX ANT
Connects DSC
antenna here.
PRINTER
Connects printer
PP-510.
EXT SP
Connects external
loudspeaker.
IEC61162-1 (NMEA)/REMOTE
Connects junction box IF-8810.
FM-8800D/8800S, rear view
Connection of Power Supply
Convention vessels, 100/220 VAC ship’s mains
Convention vessels must supply both AC and DC power to the FM-8800D/8800S, via an
AC/DC power supply unit. Both AC and DC are supplied by the AC/DC power supply unit,
and when AC input fails DC power is activated.
Connect the radio battery to the DC IN terminal on the PR-240-CE. Connect the AC ship’s
mains to the AC IN terminal on the PR-240-CE.
Radio battery (24 VDC)
Attach the connector supplied to the power cable and plug it into the 24VDC connector at
the rear of the transceiver unit. Connect the wire ends to the radio battery line.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONNECTIONS
Connection of VHF Antenna
The VHF antenna is connected to the transceiver unit with a 50 ohm coaxial cable, type
5D-2V. Be sure to leave some slack in the cable for future service and maintenance.
Lay the coaxial cable and attach an M-type plug to the cable (if necessary) as follows.
1. Remove the sheath by 20 mm.
2. Bare 13 mm of the center conductor. Trim braided shield by 5 mm and tin.
3. Slide coupling ring onto cable.
4. Screw the plug assembly on the cable.
5. Solder plug assembly to braided shield through solder holes. Solder contact sleeve to
conductor.
6. Screw coupling ring into plug assembly.
7. Screw the plug into the ANT connector at the rear of the transceiver unit.
How to attach the M-type plug to the coaxial cable
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONNECTIONS
Connection of DSC Antenna
The DSC antenna is connected to the transceiver unit with a 50 ohm coaxial cable, type
5D-2V. Attach an M-type plug to the cable (if necessary) as shown an page 2-2. Screw the
plug into the CH70 RX ANT connector at the rear of the transceiver unit.
Connection of Handset
Connect the handset cable to the HANDSET connector on the front panel.
Grounding the Transceiver Unit
Fasten a ground wire (local supply) between the GND terminal at the rear of the transceiver
unit and ship’s hull (or ground bus).
Connecting the Junction Box
The junction box is required to connect a remote station, wing handset, etc. The cable to be
connected with the transceiver unit is prefitted on the junction box at the factory. For
connection of other cables, see the interconnection diagram.
Clamp the cable with
Cable entry
U-type cable clamps.
Use one of these nuts for ground terminal between JB and ship's body.
Cable clamp: Clamp shield part of the cables to ground cables.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONNECTIONS
Connecting the Remote Station without the Junction
Box
The remote station (or DMC Interface, Mic. Receptacle box, etc) can be connected directly
to the transceiver unit, using the D-sub connector supplied as installation materials.
Attach the connector to the cable as follows.
Shield tape (metal)
Fold back the armor,
and then wind the shield
tape along the edge of cable.
Cable clamp
Cable
Connector XM2A-3701 &
Housing case XM2S-3712
Attachment of connector
When the handset HS-2003 is not connected to the
Transceiver unit
When the handset HS-2003 is not connected to the transceiver unit, i.e.,always the remoted
handset is used, the following modification is necessary.
1. Dismount the cover of the transceiver unit by removing four screws at the rear panel and
two screws at the side.
2. Dismount the bottom cover by removing seven screws.
J15
CPU board
05P0773
3. Shorten between #1 and #2 of J15. The handset line of the HANDSET port becomes
always “ON HOOK”.
4. Assemble the unit.
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONNECTIONS
Connection of AC/DC Power Supply Unit PR-240-CE
The power supply PR-240-CE is shipped ready for connection to a 200-230 VAC ship’s
mains. If the ship’s mains is 100 VAC – 115 VAC, change the tap connection and terminal
board connection as below. Attach label supplied as accessories to the punch mark in the
front panel according to the ship’s mains.
Ship’s mains
Tap connection
Terminal board
connection #1 & #2
100-115 VAC
200-230 VAC
SEL 115 V
SEL 230 V
b
a
100-115 VAC
200-230 VAC
White
Black
White
Black
1
2
3
1
2
3
Punch mark
(a)
Front
(b)
SEL
115 V
1
2
3
4
5
6
7
8
Heat sink
SEL
230 V
Tap connection (Pull out to disconnect)
Terminal board connection
Top view of AC/DC power supply unit (cover removed)
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONNECTIONS
Protective earth
Connect IV-2.0sq wire between ship’s superstructure and the ground terminal on the
PR-240-CE.
CAUTION
Attach protective earth
securely to the ship's body.
The protective earth
(grounding) is required for the
AC/DC power supply unit to
prevent electrical shock.
Attach a label here.
GND terminal
PR-240-CE Front panel
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONNECTIONS
Jumper Setting for Termination
Note: DMC interface is not used for Russian version.
It is necessary, for termination, to change the jumper setting for remote station or DMC
interface.
Open the unit(s) terminated and change the jumper plugs J2 and J3 to ON position (#2-#3).
(Default setting is OFF position.)
Junction
Box
Remote
Station
Remote
Station
Remote
Station
Transceiver
Unit
Remote
Station
Remote
Station
DMC I/F
Terminated Unit
Note that up to four remote stations can be connected.
LINE
TERMINATION
RS-485
TERMINATION
J3
J2
1
3
1
3
J1
ON
ON
Set to ON (#2-3)
for termination.
DISTRESS
VOLUME
05P0782
TB1
TB2
Remote station RB-8800
Cable entry
TB1
TB2
Set to ON (#2-3)
for termination.
J1
φ
2- 4.5
Fixing hole
Remote station RB-8810
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONNECTIONS
Remove four screws
to open the unit.
Set jumper plug to ON (#1-2).
05P0778
J4
ON
RS-485
TERMINATION
TB1
DMC Interface IF-8820
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONNECTIONS
2.10 Wire connection of VHF console
1. Remove the cover assembly and printer assembly (or concealing lid) form the console.
For the printer assembly, remove the cables connected at the Transceiver Unit and the
terminal board.
Cover assembly
Binding screw F
M4X10 8 places
Binding screw F
M4X10 4 places
Printer assembly
or Concealing lid
Console
Terminal board
2. Connect the power cable from the ship to the terminal block 1 (+) and 2 (-).
Terminal Board Wiring
1. Wiring conductor
9～10mm
2. Wiring
1)Insert a screwdriver which blade edge
is 3.5 X 0.5mm to the square hole.
2)Press the screwdriver to arrow direction
to open the spring in the round hole.
3)Insert the wire to the round hole.
4)Remove the screwdriver.
1
2
3
4
5
6
7
8
2
Power cable
from the ship
-
Square hole
Round hole
Terminal board
3. Connect the ground wire from ship to each ground terminal for the transceiver unit and
the junction box.
4. Connect cables from external equipments to the junction box.
5. Fix the printer assembly (or concealing lid) and the cover assembly.
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CONNECTIONS
This page is intentionally left blank.
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
3. ASSEMBLING CONSOLE KIT
A VHF console kit is required to mount the Transceiver Unit in the field. There are two types
as shown below.
VHF console kit
Type
RC-8800-N-75BG
RC-8800-A-75BG
Code No.
000-054-125
000-054-126
Remarks
Without printer
With printer
Assembling the Console Kit
1. Remove the cover assembly, the panel assembly and the printer assembly (or
concealing lid) from the console. For the printer assembly, remove the cable connected
to the terminal board.
Cover assembly
Binding screw F
M4X10 8 places
Binding screw F
M4X10 4 places
Printer assembly
(or Concealing lid
#
#
Remove screws( )and
detach the panel assembly.
Console
Panel assembly
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Fix the panel assembly to the Transceiver Unit with binding screws (use original binding
screws of the Transceiver Unit). Refer to the figure below.
3. Screw in hex bolts M8x16 and flat washers loosely at both sides of the Transceiver Unit.
Panel assembly
Binding screw M4 2 places
(Use the original screws
of the Transceiver Unit.)
Washer M8
2 places
Hex bolt M8X16
(faster loosely)
2 places
4. Set the Transceiver Unit to the console, remove the grommets from the console and fix
the Transceiver Unit with hex bolts using the holes formerly occupied by the grommets.
Hex head screws
Connecter
Insert console upside down.
Close the hole with grommets
lastly.
Mounting of
the Transceiver Unit
Connecter
Mounting
plate
Flat washer
Transceiver
Unit
Fix Mounting Plate
between washers.
5. Connect connector from the fuse to the power connector derived from the Transceiver
Unit.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Replace the cable attached to junction box with the cable (55 cm, 37-pin D sub) supplied
with the console kit.
Replace the original cable
with the cable assembly
DSUB37M-PHX3-L550.
A
Junction box
(without cover)
PH Connector
12P
J2
PH Connector
10P
PH Connector
14P
J3
J1
2
3
Crimp-on lug
A
View
7. Connect the cable (37-pin D sub) attached to the junction box to the Transceiver Unit
and then mount the junction box on the console.
±Binding screw F
M4X8 4 places
Cover
±Screw B
M4X10 4 places
Mounting plate
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Junction box
Grommets 2 places
8. For the console w/printer, connect the printer cable for data transmission to the
PRINTER port of the Transceiver Unit and fix the power cable to the terminal board as
before. Then, fix the printer assembly to the console. For no printer, fasten the
concealing lid to the console.
Printer
W/ Printer
Printer cable
J2
Insert the mounting plate
for printer to the catch of the console
View
9. Fasten the cover assembly.
NOTE: If the console assembly is to be mounted on the hull, refer to paragraghs 1-9 and
2-10.
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
A-5
1/1
05EC-X-9857 -1
ＰＡＣＫＩＮＧ ＬＩＳＴ
DM-2003-F
N A M E
DESCRIPTION/CODE №
O U T L I N E
Q'TY
ﾏｲｸｾｯﾄ
ﾌｯｸ
MICROPHONE SET
ZIRXXCDM002
1
1
HOOK
000-150-017
KON-003
ﾏｲｸﾛﾌｫﾝ
MICROPHONE
000-150-016
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
05EC-X-9857
Download from Www.Somanuals.com. All Manuals Search And Download.
A-6
CODE NO.
TYPE
005-377-800
05EC-X-9401 -2
1/1
CP05-09901
工事材料表
INSTALLATION MATERIALS
数量
Q'TY
番 号
NO.
名 称
NAME
型名／規格
DESCRIPTIONS
L-420
略 図
OUTLINE
用途／備考
REMARKS
ﾐﾆﾋﾟﾝ組品(1)
Used onlyJapan
1
2
3
4
1
1
1
5
CABLE ASSY.
CODE NO. 000-151-748
XM2S-3712
ｺﾈｸﾀﾌｰﾄﾞ(XM2)
HOUSING CASE
CODE NO. 000-145-423
XM2A-3701
ｺﾈｸﾀ(XM2)
CONNECTOR
CODE NO. 000-145-424
6X20 SUS304
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ 1種
SELF-TAPPING SCREW
CODE NO. 000-802-084
05EC-X-9401
ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
Download from Www.Somanuals.com. All Manuals Search And Download.
A-7
CODE NO.
TYPE
005-949-280
CP05-08701
05DY-X-9417 -0
1/1
工事材料表
INSTALLATION MATERIALS
数量
Q'TY
番 号
NO.
名 称
NAME
型名／規格
DESCRIPTIONS
5X20 SUS304
略 図
OUTLINE
用途／備考
REMARKS
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ 1種
SELF-TAPPING SCREW
1
4
CODE NO. 000-802-081
05DY-X-9417
ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
Download from Www.Somanuals.com. All Manuals Search And Download.
A-8
CODE NO.
TYPE
005-951-920
FP05-05511
05DZ-X-9502 -0
1/1
付属品表
ACCESSORIES
数量
Q'TY
番 号
NO.
名 称
NAME
型名／規格
略 図
OUTLINE
用途／備考
REMARKS
DESCRIPTIONS
4X16 SUS304 1ｼｭ
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ
1
2
2
2
SELF-TAPPING SCREW
CODE NO. 000-802-080
M4
ﾎﾟﾘｶﾜｯｼｬｰ
WASHER
CODE NO. 000-864-937
05DZ-X-9502
ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
Download from Www.Somanuals.com. All Manuals Search And Download.
A-9
CODE NO.
TYPE
005-959-720
FP05-05701
05EC-X-9502 -2
1/1
RB-8800
付属品表
ACCESSORIES
数量
Q'TY
番 号
NO.
名 称
NAME
型名／規格
DESCRIPTIONS
略 図
OUTLINE
用途／備考
REMARKS
M4
ﾎﾟﾘｶﾜｯｼｬｰ
1
2
3
4
4
4
WASHER
CODE NO. 000-864-937
4X20 SUS304
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ
SELF-TAPPING SCREW
CODE NO. 000-805-687
05-086-1102-2
ﾌﾞﾗｲﾝﾄﾞｼｰﾙ
SEAL
CODE NO. 100-281-282
05EC-X-9502
ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
Download from Www.Somanuals.com. All Manuals Search And Download.
A-10
1/1
005-377-820
SP05-05501
05EC-X-9301 -0
BOX NO.
CODE NO.
TYPE
P
SETS PER
VESSEL
SHIP NO.
SPARE PARTS LIST FOR
U S E
QUANTITY
WORKING
PER PER
REMARKS/CODE NO.
DWG. NO.
ITEM
NO.
OR
NAME OF
PART
OUTLINE
TYPE NO.
SPARE
SET VES
ﾋｭｰｽﾞ
FUSE
FGBO 15A
AC125V
2
1
000-549-014
1/1
MFR'S NAME
DWG NO.
FURUNO ELECTRIC CO.,LTD.
05EC-X-9301
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
Download from Www.Somanuals.com. All Manuals Search And Download.
A-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
D-2
Download from Www.Somanuals.com. All Manuals Search And Download.
D-3
Download from Www.Somanuals.com. All Manuals Search And Download.
D-4
Y. Hatai
Download from Www.Somanuals.com. All Manuals Search And Download.
D-5
Download from Www.Somanuals.com. All Manuals Search And Download.
D-6
Download from Www.Somanuals.com. All Manuals Search And Download.
This page is intentionally left blank.
Download from Www.Somanuals.com. All Manuals Search And Download.
D-7
Y. Hatai
Download from Www.Somanuals.com. All Manuals Search And Download.
D-8
Y. Hatai
Download from Www.Somanuals.com. All Manuals Search And Download.
D-9
Download from Www.Somanuals.com. All Manuals Search And Download.
D-10
Download from Www.Somanuals.com. All Manuals Search And Download.
D-11
Feb.02'05
Download from Www.Somanuals.com. All Manuals Search And Download.
D-12
Download from Www.Somanuals.com. All Manuals Search And Download.
D-13
Nov.28'03
Download from Www.Somanuals.com. All Manuals Search And Download.
D-14
Download from Www.Somanuals.com. All Manuals Search And Download.
D-15
Y. Hatai
Download from Www.Somanuals.com. All Manuals Search And Download.
D-16
Y. Hatai
Download from Www.Somanuals.com. All Manuals Search And Download.
D-17
Download from Www.Somanuals.com. All Manuals Search And Download.
D-18
Dec.26'03
Download from Www.Somanuals.com. All Manuals Search And Download.
D-19
Dec.26'03
Download from Www.Somanuals.com. All Manuals Search And Download.
D-20
Download from Www.Somanuals.com. All Manuals Search And Download.
S-1
1
2
3
4
5
6
*2
航法装置,プロッタ
*2
*2
NAVIGATION
DEVICE, PLOTTER
RXD(H)
Wing Mic
Wing Mic
*2
*2
マイクレセプタクルボックス
MIC RECEPTACLE BOX
マイクレセプタクルボックス
MIC RECEPTACLE BOX
ハンドセット
HANDSET
ハンドセット
HANDSET
RXD(C)
接続箱
RBD-VHF(B)
TB1
RBD-VHF(B)
TB1
TXD(H)
TXD(C)
送受信機
TRANSCEIVER UNIT
T/R用アンテナ
JUNCTION BOX
IF-8810
キ
YEL
WHT
RED
YEL
BLK
YEL
キ
YEL
WHT
RED
YEL
BLK
YEL
1
2
3
4
5
6
7
1
2
3
1
2
3
4
5
6
7
1
2
3
HS-6000FZ-11
HS-6000FZ-5
HS-6000FZ-11
HS-6000FZ-5
P
P
P
P
P
P
シロ
アカ
キ
クロ
キ
シロ
アカ
キ
クロ
キ
ANTENNA FOR T/R
*2
*2
CO-SPEVV-SB-C
0.2X2P,φ10.5
FM-8800D/S
IEC61162-1(NMEA)/REMOTE
*1
TTYCS-1 MAX. 20m
D-SUB 37P
P
*4
J1
CH70 WR用アンテナ
キ
YEL
外部アラーム
Ext. Alarm
A
B
C
D
4
4
+15VDC
+15VDC
+15VDC
+15VDC
N.C
N.C
TXD(H)
TXD(C)
RXD(H)
RXD(C)
1
2
3
4
5
1
2
3
4
5
TXD(H)
TXD(C)
RXD(H)
RXD(C)
F.GND
1
2
3
4
P
P
ダイ ORG
アカ RED
チャ BRN
ANTENNA FOR CH70 WR
*2
*1
P
P
P
P
5
CO-SPEVV-SB-C 0.2x5P,φ13.5 MAX. 20m *2
ハンドセット
*2
EXT.ALM_N
*7
6
7
8
9
10
6
7
8
9
10
6
7
8
9
CO-SPEVV-SB-C 0.2x5P,φ13.5 MAX.20m *2
ANT
0V
F.GND
M-P-5
M-P-5
1
2
*4
*4
アカ RED
ハンドセット
ハンドセット
ハンドセット
W-MIC1(H)
W-MIC1(C)
W-SP1(H)
W-SP1(C)
W-PTT1_N
0V
P
P
P
キ
YEL
クロ BLK
YEL
シロ WHT
YEL
*2
*2
*2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
HANDSET
HANDSET
HS-8800
HANDSET
HS-8800
HANDSET
HS-8800
CH70 RX ANT
HS-8800
キ
J2
1
2
EXT.ALM_N 11
1
2
3
4
5
キ
リモートステーション
リモートステーション
REMOTE STATION
RB-8800/RB-8810
リモートステーション
リモートステーション
P
P
P
P
P
P
1
2
3
4
0V
W-MIC1(H)
W-MIC1(C)
W-SP1(H)
W-SP1(C)
W-PTT1_N
0V
12
13
14
15
16
17
18
19
20
21
22
*2
*2
*2
*2
REMOTE STATION
RB-8800/RB-8810
REMOTE STATION
RB-8800/RB-8810
REMOTE STATION
RB-8800/RB-8810
F.GND
アカ RED
W-MIC2(H)
W-MIC2(C)
W-SP2(H)
W-SP2(C)
W-PTT2_N
0V
P
P
P
DATA_A
DATA_B
1
2
DATA_A
DATA_B
CONT
1
2
3
4
5
6
7
8
9
DATA_A
DATA_B
CONT
DIST_SW
1
2
3
4
5
6
7
8
9
DATA_A
DATA_B
CONT
1
2
3
4
5
6
7
8
9
キ
YEL
クロ BLK
YEL
シロ WHT
YEL
*3
*3
*3
*3
6
7
8
9
10
11
12
*5
CONT
DIST_SW
3
4
キ
DIST_SW
LINE OUT(H)
LINE I/O(C)
LINE IN(H)
+15V1
DIST_SW
LINE OUT(H)
LINE I/O(C)
LINE IN(H)
+15V1
LINE OUT(H)
LINE I/O(C)
LINE IN(H)
+15V1
5
LINE OUT(H)
LINE I/O(C)
LINE IN(H)
+15V1
キ
0V
0V
0V
0V
6
7
8
F.GND
VDR AF(H)
TTYCS-1 MAX. 20m *1
HANDSET
S.GND
VDR
ハンドセット
VDR AF(C)
NOT USED_1
NOT USED_2
F.GND
1
2
3
4
5
6
7
8
OV
F.GND
OV
F.GND
OV
F.GND
OV
F.GND
9
10
*4
PTT SW_N
MIC(H)
MIC(C)
HS SP(H)
HOOK SW_N
+5V
HANDSET
HS-2003
10
10
10
終端まで最大50m
MAX. 50m TO LAST UNIT
シロ(太) WHT(BIG)
クロ(太) BLK(BIG)
ミドリ
アオ
キ
ダイ
アカ
チャ
*2
05S0309
J3
TB2
TB2
TB1
TB2
TB1
TB2
TB1
TB1
VDR AF(H)
VDR AF(C)
DATA_A
1
2
3
4
5
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
シロ(太) WHT(BIG)
P
P
P
P
P
P
P
+15VDC
0V
DATA_A
DATA_B
+15VDC
OV
DATA_A
DATA_B
LINE IN(H)
LINE IN(C)
LINE OUT(H)
LINE OUT(C)
TB3
1
2
3
4
5
6
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
P
P
クロ(太) BLK(BIG)
ミドリ GRN
GRN
BLU
YEL
ORG
RED
BRN
DATA_B
P
P
P
アオ
アカ
BLU
RED
BRN
YEL
ORG
F.GND
LINE OUT(H)
LINE OUT(C)
LINE IN(H)
LINE IN(C)
W-MIC2(H)
W-MIC2(C)
W-SP2(H)
W-SP2(C)
W-PTT2_N
0V
LINE IN(H)
LINE IN(C)
LINE OUT(H)
LINE OUT(C)
F.GND
6
7
8
9
10
11
12
13
14
左と同じ
Same as
left
左と同じ
Same as
left
P
チャ
キ
7
8
P
P
ダイ
TB3
TB3
TB3
*4
SPKR
N.C
+15VDC
0V
DATA_A
DATA_B
外部スピーカ
EXT. SP
シロ(太) WHT(BIG)
クロ(太) BLK(BIG)
ミドリ
アオ
キ
ダイ
アカ
チャ
SP(H)
SP(C)
1
2
IV-1.25 *1
IV-1.25sq. *1
IV-1.25sq. *1
IV-1.25sq. *1
2.8 m
P
P
P
GRN
BLU
YEL
ORG
RED
BRN
SEM-21Q
*2
リモートステーション
REMOTE STATION
RB-8800/RB-8810
*2
05S0309
F.GND
*2
LINE IN(H)
LINE IN(C)
LINE OUT(H)
LINE OUT(C)
F.GND
*2
ハンドセット
終端まで最大50m
MAX. 50m TO LAST UNIT
上に同じ
Same as
above
HANDSET
HS-8800
*3
*5
*1
P
*2
D-SUB 25P
DPYC-1.5
100-115/
200-230 VAC
PRINTER
AC/DC電源
*4
AC
IN
*2
DMC I/F
IF-8820
N.C
N.C
STROBE_N
D0
D1
1
2
3
4
5
AC-DC POWER
SUPPLY
PR-240-CE
TB2
TB1
*1
DPYC-2.5
24 VDC
1
2
3
4
5
6
7
8
11
12
13
14
17
18
15
16
19
1
2
3
4
5
6
7
8
+15VDC
OV
D2
D3
D4
D5
D6
D7
*2
DC
+
-
+ 24VDC
- IN
IV-1.25sq.
*1
DATA_A
DATA_B
LINE IN(H)
LINE IN(C)
LINE OUT(H)
LINE OUT(C)
TB3
OUT
6
7
8
9
上に同じ
Same as
above
PE 保護アース
IV-2sq. *1
24VDC
遭難警報装置
*2
ACK_N
BUSY
PE
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
DISTRESS MESSAGE CONTROLLER
DMC-5
RED
BLK
RED
BLK
VCTF0.75x3C,5m,φ7
F.GND
9 F.GND
10 N.C
24VDC(+)
24VDC(-)
*2
24 VDC
24VDC
プリンタ
PRINTER
アカ RED
クロ BLK
シロ WHT
*1
05S9371,3m
17JE-23250-02,3m
IV-1.25sq.
+
-
1
2
3
SELECT
ALF_N
ERROR_N
INIT._N
SLCT IN_N
F.GND
0V
*4
TB1/TB2
注記 *1）造船所手配。
*2）オプション。
15A
ダイ ORG
YEL
チャ BRN
アカ RED
TXD(H)
TXD(C)
RXD(H)
RXD(C)
F.GND
1
2
3
4
6
TXD(H)
TXD(C)
RXD(H)
RXD(C)
F.GND
20
21
22
23
24
P
P
キ
PP-510
GND
*3）最大4台まで接続可能。
*4）ケーブルクランプで接地。
*5）終端のユニットでは内部で
ジャンパー(J2, J3)をONにする。
*6）P: 撚り対線
IV-1.25sq.
*1
*1 CO-SPEVV-SB-C
0.2x2P(5/10/15/20/30m)
F.GND
F.GND
F.GND
F.GND
F.GND
F.GND
IV-1.25sq.
*1
*7）ノーマルクローズ、フローティング
最大80mA、耐圧≦50V。
DRAWN
Jun. 9,'06
TITLE
名称
FM-8800D/S
NOTE *1. SHIPYARD SUPPLY
*2. OPTION
E.MIYOSHI
VCTF0.75x2C,3m
*2
24VDC
プリンタ
PRINTER
シロ WHT
クロ BLK
CHECKED
+
-
1
2
国際VHF無線電話装置
相互結線図
TAKAHASHI.T
*3. Max. 4 sets
GND
*1
*4. GROUND THROUGH CABLE CLAMP.
*5. CONNECT JUMPERS (J2 & J3)
ON TERMINATED REMOTE STATION.
*6. P: TWISTED PAIR CABLE
*7. NORMAL CLOSE, FLOATING, MAX80mA,
WITHSTAND VOLTAGE ≦50V.
APPROVED
SCALE
Y. Hatai
PP-8800
MASS
kg
NAME
IV-1.25sq.
*1
VHF RADIOTELEPHONE
IV-2sq.
DWG No.
INTERCONNECTION DIAGRAM
C5642-C01- J
FURUNO ELECTRIC CO., LTD.
Download from Www.Somanuals.com. All Manuals Search And Download.
S-2
1
2
3
4
5
6
T/R用アンテナ
*2
ANTENNA FOR T/R
接続箱
JUNCTION BOX
送受信機
TRANSCEIVER UNIT
FM-8800D/S
TTYCS-4(*1) OR
CO-SPEVV-SB-C
0.2x2P,φ10.5(*2)
航法装置/プロッタ
NAVIGATOR
PLOTTER
IF-8810
J1
TXD-H
1
2
3
4
5
6
7
8
9
ANT
J1
CH70 WR用アンテナ
*2
ANTENNA FOR CH70 WR
P
P
IEC61162-1(NMEA)/REMOTE
XM2A-3701
P
TXD-C
RXD-H
RXD-C
M-P-5
M-P-5
+15VDC
+15VDC
+15VDC
+15VDC
NC
NC
1
2
3
4
5
1
2
1
2
A
B
C
D
*1
TTYCS-1,MAX.20m
*2
CO-SPEVV-SB-C 0.2x5P,
φ13.5,MAX.20m
アカ RED
*4
*4
F.GND
EXT.ALM-N
3
4
外部アラーム
*1
EXTERNAL ALARM
CH70 RX ANT
J2
P
P
P
P
*7
1
2
5
0V
F.GND
W_MIC1-H
Wing Mic
6
7
6
7
8
ハンドセット
HANDSET
*2
HS-6000FZ-11
HS-6000FZ-5
TXD-H
TXD-C
RXD-H
RXD-C
1
2
3
4
5
7
TB1
マイクレセプタクル
ボックス
MIC RECEPTACLE
P
P
P
ハンドセット
HANDSET
HS-2003
HANDSET
W_MIC1-C 10
W_SP1-H 11
W_SP1-C 12
8
9
10
キ
YEL
クロ BLK
YEL
シロ WHT
YEL
1
2
3
4
S.GND
9
10
1
2
3
4
5
6
7
8
キ
PTT SW-N
MIC-H
MIC-C
HS SP-H
HOOK SW-N
+5V
BOX
W_PTT1-N
13
0V 14
J2
RBD-VHF(B)
*2
EXT.ALM-N 11
0V 12
W_MIC1-H 13
W_MIC1-C
W_SP1-H
W_SP1-C
W_PTT1-N
0V
1
2
キ
*2
P
P
P
P
P
P
*4
F.GND 15
CO-SPEVV-SB-C 0.2x5P,
φ13.5,MAX.20m
アカ RED
Wing Mic
3
ハンドセット
W_MIC2-H 16
W_MIC2-C 17
W_SP2-H 18
W_SP2-C 19
W_PTT2-N 20
0V 21
4
5
6
7
8
9
1
2
3
4
5
7
14
15
16
17
18
19
20
21
22
TB1
1
2
3
4
マイクレセプタクル
ボックス
MIC RECEPTACLE
BOX
RBD-VHF(B)
*2
HANDSET
*2
HS-6000FZ-11
HS-6000FZ-5
キ
YEL
クロ BLK
YEL
シロ WHT
YEL
F.GND
キ
SPKR
SP-H
SP-C
外部スピーカ
EXT. SPEAKER
SEM-21Q
*2
φ3.5
2.8m
0V
0V
0V
0V
キ
*4
*4
F.GND 22
10
11
12
ハンドセット
HANDSET
HS-8800
ハンドセット
HANDSET
*2
HS-8800
*1
TTYCS-1,MAX.20m
*2
VDR AF-H 23
VDR AF-C
24
VDR
J3
VDR AF-H
VDR AF-C
DATA-A
1
2
3
NOT USED_1 25
NOT USED_2 26
F.GND 27
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
P
P
P
P
P
P
P
終端まで最長50m
TOTAL 50m OR LESS TO TERMINATE
*2
05S0309
*2
05S0309
シロ(太) WHT[B]
DATA-B
4
TB1
TB2
TB1
TB2
*5
LINE OUT-H
LINE OUT-C
LINE IN-H
LINE IN-C
W_MIC2-H
W_MIC2-C
W_SP2-H
W_SP2-C
W_PTT2-N
0V
5
6
+15VDC 28
0V 29
シロ(太) WHT[B]
クロ(太) BLK[B]
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
リモートステーション
REMOTE STATION
RB-8800/RB-8810
<No.3/No.4>
P
P
P
P
リモートステーション
REMOTE STATION
RB-8800/RB-8810
リモートステーション
クロ(太) BLK[B]
REMOTE STATION
RB-8800/RB-8810
<No.2>
DATA-A 30
7
ミドリ
アオ
アカ
チャ
キ
GRN
BLU
RED
BRN
YEL
ORG
ミドリ
アオ
アカ
チャ
キ
GRN
BLU
RED
BRN
YEL
ORG
GND
DATA-B 31
8
<No.1>
*3
*3
LINE IN-H 32
LINE IN-C 33
LINE OUT-H 34
LINE OUT-C 35
F.GND 36
LINE IN-H
LINE IN-C
LINE OUT-H
LINE OUT-C
9
10
11
12
13
14
ダイ
ダイ
*4
*1
IV-1.25sq.
*1
IV-1.25sq.
NC 37
終端まで最長50m
TOTAL 50m OR LESS TO TERMINATE
*2
05S0309
*2
05S0309
シロ(太) WHT[B]
F.GND
TB1
ハンドセット
HANDSET
*2
+15VDC
0V
38
39
40
41
42
43
44
45
46
47
48
シロ(太) WHT[B]
クロ(太) BLK[B]
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
1
2
3
4
5
6
7
8
P
P
P
P
DMC I/F
IF-8820
リモートステーション
REMOTE STATION
RB-8800/RB-8810
PRINTER
クロ(太) BLK[B]
D-SUB 25P
*2
HS-8800
DATA-A
DATA-B
LINE IN-H
LINE IN-C
LINE OUT-H
LINE OUT-C
F.GND
1
ミドリ
アオ
アカ
チャ
キ
GRN
BLU
RED
BRN
YEL
ORG
ミドリ
アオ
アカ
チャ
キ
GRN
BLU
RED
BRN
YEL
ORG
*1
DPYC-2.5
TB1
1
2
3
4
5
6
7
8
15A
24VDC
24VDC(+)
24VDC(-)
RED
BLK
*3
*5
リモートステーション
REMOTE STATION
RB-8800/RB-8810
25
非常灯
*2
EMERGENCY LAMP
ダイ
18
F.GND 19
ダイ
*4
F.GND
*1
IV-1.25sq.
NC
NC
10 NC
1 ～ 36
I/F
S1
J3
0V
J2
*2
CO-0.2x2P,5/10/15/20/30m
P
TB1/TB2
TXD-H
TXD-C
RXD-H
RXD-C
F.GND
1
2
3
遭難警報装置
DISTRESS MESSAGE
CONTROLLER
DMC-5
TXD-H 20
TXD-C 21
RXD-H 22
RXD-C
23
F.GND 24
1
2
3
4
5
05P0541
24V
J1
*6
P
1 ～ 34
*1
IV-1.25sq.
*1
IV-1.25sq.
1 ～ 34
J2
プリンタ
PRINTER
UTP-80FK
*6
RACK CONSOLE
注記
NOTE
DRAWN
TITLE
*1）造船所手配。
*2）オプション。
*3）最大4台まで接続可能。
*4）ケーブルクランプで接地。
*5）終端ユニットは内部のジャンパー（J2,J3）をONにする。
RC-8800 (FM-8800)
*1. SHIPYARD SUPPLY
*2. OPTION
*3. MAX. 4 SETS AVAILABLE
*4. GROUND THROUGH CABLE CLAMP.
*5. CONNECT JUMPERS (J2 & J3) ON TERMINATED REMOTE STATION.
*6. IN CASE OF "W/PRINTER"
Jun.9,'06
E.MIYOSHI
CHECKED
名称
国際VHF無線電話装置（ラック組込）
相互結線図
TAKAHASHI.T
Y. Hatai
APPROVED
SCALE
MASS
kg
NAME
*6）プリンタ有の場合
VHF RADIOTELEPHONE (RACK CONSOLE)
INTERCONNECTION DIAGRAM
DWG No.
*7）ノーマルクローズ、フローティング、最大80mA、耐圧≦50V。
*7. NORMAL CLOSE, FLOATING, MAX80mA, WITHSTAND VOLTAGE ≦50V.
C5642-C02- D
FURUNO ELECTRIC CO., LTD.
Download from Www.Somanuals.com. All Manuals Search And Download.
S-3
1
2
3
4
5
6
T/R用アンテナ
送受信機
TRANSCEIVER UNIT
FM-8800D/S
ANTENNA FOR T/R
*2
*2
航法装置,プロッタ
Wing Mic
ハンドセット
HANDSET
マイクレセプタクルボックス
*2
CH70 WR用アンテナ
*2
NAVIGATION
DEVICE, PLOTTER
RXD(H)
D-SUB 37P
IEC61162-1(NMEA)/REMOTE
MIC RECEPTACLE BOX
ANTENNA FOR CH70 WR
*2
CO-SPEVV-SB-C 0.2X2P,φ10.5
キ
ダイ
アカ
チャ
A
B
C
D
YEL
ORG
RED
BRN
RBD-VHF(B)
TB1
TXD(H)
TXD(C)
RXD(H)
RXD(C) 10
F.GND 37
7
8
9
*2
P
P
RXD(C)
キ
シロ
YEL
WHT
1
2
3
4
5
6
7
1
2
3
HS-6000FZ-11
HS-6000FZ-5
TXD(H)
TXD(C)
P
P
P
アカ RED
YEL
クロ BLK
YEL
ANT
M-P-5
M-P-5
キ
1
2
*4
*1
TTYCS-1 MAX. 20m
4
外部アラーム
Ext. Alarm
EXT.ALM_N 11
キ
*5
12
0V
*1
CH70 RX ANT
F.GND 37
*4
アカ
キ
クロ
キ
シロ
キ
RED
YEL
BLK
YEL
WHT
YEL
1
2
W-MIC1(H) 13
W-MIC1(C) 14
W-SP1(H) 15
W-SP1(C) 16
W-PTT1_N 17
0V 18
P
P
P
CO-SPEVV-SB-C 0.2x5P,φ13.5 MAX. 20m *2
F.GND 37
*4
*4
TTYCS-1 MAX. 20m *1
VDR AF(H) 23
VDR AF(C) 24
F.GND 37
VDR
HANDSET
ハンドセット
S.GND
1
2
3
4
5
6
7
8
シロ(太) WHT(BIG)
クロ(太) BLK(BIG)
*2
05S0309
PTT SW_N
MIC(H)
MIC(C)
HS SP(H)
HOOK SW_N
+5V
+15VDC
0V 19
DATA_A 25
1
HANDSET
HS-2003
P
P
P
P
ミドリ
アオ
キ
ダイ
アカ
チャ
GRN
BLU
YEL
ORG
RED
BRN
終端まで最大50m
MAX. 50m TO LAST UNIT
DMC I/F
IF-8820
*2
DATA_B 26
LINE IN(H) 27
LINE IN(C)
LINE OUT(H) 29
30
28
1
2
3
4
5
6
7
8
11
12
13
14
17
18
15
16
19
F.GND
LINE OUT(C)
F.GND 37
*4
アカ
キ
クロ
キ
シロ
キ
RED
W-MIC2(H) 31
P
P
P
YEL
BLK
YEL
WHT
YEL
32
W-MIC2(C)
SPKR
遭難警報装置
W-SP2(H) 33
W-SP2(C) 34
W-PTT2_N 35
0V 36
外部スピーカ
EXT. SP
SP(H)
SP(C)
1
2
2.8 m
DISTRESS MESSAGE CONTROLLER
DMC-5
F.GND
9 F.GND
10 N.C
SEM-21Q
*2
*3
TB1/TB2
F.GND 37
ダイ ORG
YEL
チャ BRN
アカ RED
TXD(H)
TXD(C)
RXD(H)
RXD(C)
F.GND
1
2
3
4
6
TXD(H)
TXD(C)
RXD(H)
RXD(C)
F.GND
20
21
22
23
24
*4
P
P
キ
*1
*2
D-SUB 25P
CO-SPEVV-SB-C
0.2x2P(5/10/15/20/30m),φ10.5
PRINTER
DPYC-1.5
AC/DC電源
100-115/200-230 VAC
AC
IN
*2
STROBE_N
D0
D1
1
2
3
4
5
AC-DC POWER
SUPPLY
PR-240-CE
IV-1.25sq.
*1
*1
D2
D3
D4
D5
D6
D7
DPYC-2.5
+
-
DC
+
-
24 VDC
24 VDC
IN
CO-SPEVV-SB-C 0.2x5P,φ13.5 MAX. 20m *2
OUT
6
7
8
9
*2
PE 保護アース
IV-2sq. *1
Wing Mic
ハンドセット
マイクレセプタクルボックス
*2
24 VDC
ACK_N
BUSY
PE
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
MIC RECEPTACLE BOX
*2
HANDSET
VCTF0.75x3C,5m,φ7
RBD-VHF(B)
TB1
05S9371,3m
RED
BLK
RED
BLK
*2
24 VDC(+)
24 VDC(-)
24VDC
24 VDC
プリンタ
PRINTER
アカ RED
クロ BLK
シロ WHT
17JE-23250-02,3m
キ
YEL
+
-
1
2
3
SELECT
ALF_N
ERROR_N
INIT._N
SLCT IN_N
F.GND
0V
1
2
3
4
5
6
7
1
2
3
HS-6000FZ-11
HS-6000FZ-5
P
P
P
シロ WHT
アカ RED
15A
PP-510
GND
注記
*1）造船所手配。
*2）オプション。
*3）ケーブルクランプで接地。
*4）コネクタクランプで接地。
キ
YEL
クロ BLK
YEL
IV-1.25sq.
4
*1
キ
VCTF0.75x2C,3m
24VDC
F.GND
F.GND
F.GND
F.GND
F.GND
F.GND
*5）ノーマルクローズ、フローティング
最大80mA、耐圧≦50V。
NOTE
*2
DRAWN
Jun. 9,'06
TITLE
プリンタ
PRINTER
FM-8800D/S
シロ WHT
クロ BLK
E. MIYOSHI
+
-
1
2
*1. SHIPYARD SUPPLY
*2. OPTION
GND
*1
CHECKED
名称
国際VHF無線電話装置
相互結線図（接続箱無し）
VHF RADIOTELEPHONE
TAKAHASHI.T
PP-8800
*3. GROUND THROUGH CABLE CLAMP.
*4. GROUND THROUGH CONNECTOR CLAMP.
*5. NORMAL CLOSE, FLOATING, MAX80mA,
APPROVED
SCALE
Y. Hatai
IV-1.25sq.
*1
IV-2sq.
MASS
kg
NAME
WITHSTAND VOLTAGE ≦50V.
P: 撚り対線
P: TWISTED PAIR CABLE
DWG No.
INTERCONNECTION DIAGRAM(W/O J.B.)
C5642-C03- D
FURUNO ELECTRIC CO., LTD.
Download from Www.Somanuals.com. All Manuals Search And Download.
|