Frymaster, a member of the Commercial Food Equipment Service Association, recommends
using CFESA Certified Technicians.
24-Hour Service Hotline 1-800-551-8633
FEB 2001
8 1 9 5 7 3 3
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 KFC-1 SMS Computer Controls
KFC-1 SMS Computer
Button
Function
On/Off
Turns the fryer ON and OFF.
For a full-pot fryer, press either ON/OFF switch to turn the computer on.
For a split-pot fryer, press the left ON/OFF switch to operate the left pot and
press the right ON/OFF switch to operate the right pot.
Product Buttons
Each of the 10 product buttons selects a cook cycle, starts the cycle, cancels the
cycle, and stops the end-of-cycle alarm. A flashing LED above the product
number indicates that product has been selected.
In programming mode, these buttons are used to select the head count, cook
time, setpoint, flex, and alarm settings.
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 KFC-1 SMS Computer Controls (cont.)
Button Function
Program Scan
Shows the remaining cook time for other active cook cycles when operating in
the multiple cook cycle mode.
In programming mode, this button activates programming mode, and
advances through the programming steps.
Enter
Shows the remaining cook time.
In programming mode, this button is pressed to move to the next step in the
programming sequence.
Temp
Shows the actual fryer temperature.
Pressing twice will show programmed setpoint temperature. Pressing three times
will show time.
In programming mode, this button is pressed to select menu options.
Exit/Cool Filter
Returns the computer and fryer from the standby mode to normal operating
mode.
During Filter Lockout Mode, pressing this button returns fryer and computer to
the setback mode once filtering has been completed. During operating mode,
press left Exit/Cool Filter to view time.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 Morning (AM) Polishing Cycle
1
Computer
ON/OFF button
to turn fryer ON.
Computer display changes to PLSH.
2
3
Assemble filter. Sprinkle 8 ounces
of filter powder over filter paper in
filter pan.
Press EXIT/COOL FILTER button on computer
face.
4
5
When the fryer reaches filtration setpoint, the display alternates between START and
PLSH.
Open drain valve. Turn pump ON. Computer displays PLSH 30:00 to polish shortening for 30 min.
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 Morning (AM) Polishing Cycle (cont.)
6
Computer counts down. Polishing lasts 30 minutes.
7
Computer displays FILL
and an alarm sounds.
Press Exit/Cool Filter to
shut off alarm.
8
Close drain
valve. Pump
shortening into
frypot. Turn
pump OFF.
9
Press
Press
EXIT/COOL
FILTER
button
EXIT/COOL
FILTER
button
Cool appears in right display.
10
Computer displays oil temperature
and fryer heats to setpoint.
Fryer displays drop when it’s at
setpoint and ready to cook.
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Afternoon (PM) Polishing Cycle
1
Assemble filter. Sprinkle filter powder over filter paper in filter pan.
2
At 2 p.m. an alarm sounds and computer display alternates between START and PLSH.
3
Press EXIT/COOL FILTER button on computer
face to shut off alarm.
4
Open drain valve. Turn pump ON. Computer displays PLSH 30:00 to polish shortening for 30 minutes.
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Afternoon (PM) Polishing Cycle (cont.)
5
Computer counts down.
6
At the end of the polishing
cycle, the computer displays
FILL and an alarm sounds.
Press Exit/Cool Filter to shut
off alarm.
7
Pump shortening into
frypot.
Turn pump off.
Press
8
Press
EXIT/COOL
FILTER
button
EXIT/COOL
FILTER
button
COOL appears in right display.
9
Computer displays LOW and fryer
heats to setpoint.
Fryer displays DROP when
oil/shortening temperature is at
setpoint and ready to cook.
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
1.6 Delaying Afternoon (PM) Polishing Cycle
1
At 2 p.m. an alarm sounds and computer display alternates between START and PLSH.
2
Press and hold PROG SCAN and ENTER buttons for five seconds.
3
Press EXIT/COOL FILTER button on computer
face and fryer returns to Drop mode.
4
Display alternates between DYPL and the oil temperature.
5
Press any program button. The fryer will cook normally until the preprogrammed delay period expires.
The polish can only be delayed once. Polish must be performed within three-hour period or the controller
will go into polish lockout.
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
1.7 Using Polish Now Feature
1
Computer display alternates between DYPL and temperature display, indicating the polish
cycle has been delayed.
Assemble filter. Sprinkle 8 ounces of filter powder over filter paper in filter pan.
2
3
Press and hold both EXIT/COOL FILTER buttons
on computer face.
4
5
Computer displays START and PLSH.
Press EXIT/COOL FILTER button on computer face to
shut off alarm.
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
1.7 Using Polish Now Feature (cont.)
6
Open drain valve. Turn pump on. Computer displays PLSH 30:00 to polish shortening for 30
min.
7
Computer counts down
8
Computer displays FILL and an
alarm sounds. Press Exit/Cool
Filter to cancel alarm.
9
Close drain valve. Pump shortening into frypot. Watch for bubbles to form in the frypot. Turn
pump off.
10
Press
Press
EXIT/COOL
FILTER
button.
EXIT/COOL
FILTER
button to exit
COOL mode.
Computer displays COOL.
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
1.7 Using Polish Now Feature (cont.)
11
Computer displays LOW and fryer
heats to setpoint.
Fryer displays DROP when oil/shortening
temperature is at setpoint and ready to
cook.
1.8 Operating Instructions
1
Turn the fryer ON for cooking operations.
2
Fryer is heating.
If HEAT light alternates on and off, it indicates the
fryer is in the melt cycle.
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
1.8 Operating Instructions (cont.)
3
Select a product, i.e. product
4. Fryer heats to preset
temperature.
Note: If the wrong product
button was selected, press
and hold button for three
seconds to cancel product
selection.
Computer displays LOW.
4
Oil temperature at 255 °F (124 °C). Actual
oil temperature will be displayed until oil
temperature is within ±2 °F (±1 °C) of
setpoint temperature (SET--TEMP).
5
Computer displays DROP. Drop
product into frypot. The
oil/shortening has reached
setpoint temperature.
Press product button to start
timer.
6
Press the TEMP button during the cook cycle countdown to
check actual cooking temperature (if desired). Pressing the
TEMP button twice will display set temperature for the selected
product.
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
1.8 Operating Instructions (cont.)
7
Pressing the flashing
product number will
stop the alarm and return
the fryer to selected
standby cycle mode
(COOL, SET--TEMP,
FILTER).
Computer displays DONE and an
alarm sounds. Cook cycle is
complete.
8
Pressing EXIT/COOL
FILTER button will exit
COOL standby mode
and return fryer to a
previous setpoint
temperature.
Computer displays COOL
indicating oil/shortening has
cooled to a standby temperature
of 250 °F (121 °C).
9
Computer displays FILTER indicating that a pre-selected
number of cook cycles has been reached and the
oil/shortening needs filtering. If FILTER displays during
a busy time of day, a cook cycle can be initiated.
Computer does not lock out.
If filtering is chosen, open drain valve. The computer
will lock out after drain valve is open for 4 seconds.
Computer display alternates between DRAIN and OPEN, indicating that drain valve is open,
and the computer is locked out.
After drain valve is open for 30 seconds, Computer display alternates between DRAIN,
OPEN and FILL, indicating that the filtering process can be initiated.
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
1.8 Operating Instructions (cont.)
10
To begin the filtering cycle, close drain valve.
Computer will display FILL. Turn filter pump on
and allow frypot to refill. After bubbles appear in
frypot for 15 seconds, close return valve and turn
filter pump OFF.
11
Press EXIT/COOL FILTER button to clear lockout and FILL message. Computer will display
COOL, indicating fryer has returned to cool standby mode. Press EXIT/COOL FILTER button
again to return fryer to previous setpoint temperature.
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
KFC-1 SMS COMPUTER
CHAPTER 2: PROGRAMMING INSTRUCTIONS
2.1 General
The KFC-1 SMS Computer arrives with a default program loaded in its nonvolatile memory.
Nonvolatile memory retains product-cooking instructions so this information will not be lost if there
is a power surge or outage.
To begin programming, ensure the computer is OFF on each side and both displays show OF F .
When ready, press the PROG SCAN button. When CODE is displayed, enter 1 6 5 0, in that
sequence, to enter the product programming mode. Below is detailed information for specific
products (See Section 2.2).
NOTE: When programming products, program the product being cooked in Product Selection
buttons labeled the same (i.e. Extra Crispyä /Hot & Spicy- "Hand dropped":
)
2.2 Programming the Computer for Product Entry
1
Computer displays CODE
in the left display and
(Blank) in the right
display.
Press ON/OFF button to turn computer OFF.
Press PROG SCAN button to enter CODE.
2
Enter Code #: 1 6 5 0, in that sequence.
As each number is entered, dashes appear in the
right display. Product is ready for programming
after the last number is entered.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.1 Programming for Extra Tasty Crispy Chicken
Enter Programming Mode as outlined in Section 2.2
1
Press button #1 for product.
Computer displays PRODUCT.
2
Computer displays HEADS.
Press button #4 to set head count to "4".
Press ENTER for next step.
3
Computer displays INTERVAL in the left display
and PROD 1 in the right display.
Press button #1 to set Product 1 Interval
#1.
4
Computer displays
COOKTIME.
Enter 1 3 0 0, in that sequence. Press
ENTER to program cook time of 13
minutes for interval #1.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.1 Programming for Extra Tasty Crispy Chicken (cont.)
5
Computer displays SET--TEMP.
Enter 3 4 0, in that sequence. Press
ENTER to save 340 °F (171 °C) as set--
temp for interval #1.
6
Computer displays FLEX.
Press button #0 to set straight time
cooking mode. Press ENTER to lock in
setting.
7
8
Computer displays INTERVAL in the left display
and PROD 1 in the right display.
Press button #2 to set Product 1 Interval
#2.
Computer displays
COOKTIME.
Enter 1 2 5 0, in that sequence. Press
ENTER to program cook time of 12
minutes, 30 seconds for interval #2.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.1 Programming for Extra Tasty Crispy Chicken (cont.)
9
Computer displays SET--TEMP.
Enter 3 1 0, in that sequence. Press
ENTER to save 310 °F (154 °C) as set--
temp for interval #2.
10
Computer displays FLEX.
Press button #0 to set straight time
cooking mode. Press ENTER to lock in
setting.
11
12
Computer displays INTERVAL in the left display
and PROD 1 in the right display.
Press button #3 to set Product 1 Interval
#3.
Computer displays
COOKTIME.
Enter 6 0 0, in that sequence. Press
ENTER to program cook time of 6
minutes for interval #3.
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.1 Programming for Extra Tasty Crispy Chicken (cont.)
13
Computer displays SET--TEMP.
Enter 3 3 0, in that sequence. Press
ENTER to save 330 °F (166 °C) as set--
temp for interval #2.
14
Press button #0 to set
straight time cooking
mode. Press ENTER
to lock in setting.
Computer displays FLEX.
15
Computer displays INTERVAL in the left display
and PROD 1 in the right display.
Press PROG SCAN to advance to pre-
set alarm program mode.
16
Computer displays
PREALM 1.
Enter 1 1 0 0, in that sequence. Press
ENTER to set alarm to 11 minutes cook
time remaining.
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.1 Programming for Extra Tasty Crispy Chicken (cont.)
17
Computer displays
PREALM 2.
Enter 0 0, in that sequence. Press PROG SCAN button to
advance to Exit Cycle program mode.
18
Computer displays EX-CYCLE in the left display
and SET--TEMP in the right display.
Press TEMP button to toggle
between SET--TEMP, COOL
AND FILTER. Stop
selection at FILTER.
Press ENTER to set Filter
Counter Mode.
Computer displays FILTER.
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.1 Programming for Extra Tasty Crispy Chicken (cont.)
19
Computer displays NUM FILT.
Press button #1 to select Filter Lockout
mode of "1". Press ENTER to set Filter
Lockout Mode of "1".
20
21
Computer displays INTERVAL in the left display
and PROD 1 in the right display.
Press TEMP button to exit Product #1
programming.
Press ON/OFF button to exit
programming mode.
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.2 Programming for Colonel’s Crispy Strips
Enter Programming Mode as outlined in Section 2.2
1
Press button #2 for product.
Computer displays PRODUCT.
2
Computer displays HEADS.
Press button #0 to set head count to "0".
Press ENTER for next step.
3
Computer displays INTERVAL in the left display
and PROD 2 in the right display.
Press button #1 to set Product 2 Interval
#1.
4
Computer displays
COOKTIME.
Enter 4 3 0, in that sequence. Press
ENTER to program cook time of 4
minutes, 30 seconds for interval #1.
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.2 Programming for Colonel’s Crispy Strips (cont.)
5
Computer displays SET--TEMP.
Enter 3 4 0, in that sequence. Press
ENTER to save 340 °F (171 °C) as set--
temp for interval #1.
6
Computer displays FLEX.
Press button #3 to set flex mode = "3".
Press ENTER to lock in setting.
7
Computer displays INTERVAL in the left display
and PROD 2 in the right display.
Press PROG SCAN to advance to pre-
set alarm program mode.
8
Computer displays
PREALM 1.
Enter 0 0, in that sequence. Press
ENTER to set alarm to zero minutes cook
time remaining.
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.2 Programming for Colonel’s Crispy Strips (cont.)
9
Press PROG SCAN
button to advance to
Exit Cycle program
mode.
Computer displays
PREALM 2.
10
Computer displays EX-CYCLE in the left display
and SET--TEMP in the right display.
Press ENTER button to save default setting of
SET--TEMP.
11
Computer displays INTERVAL in the left display
and PROD 2 in the right display.
Press TEMP button to exit Product #2
programming.
12
Press ON/OFF button to exit
programming mode.
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.3 Programming for Hot Wings/Hot BBQ Wings
Enter Programming Mode as outlined in Section 2.2
1
Press button #3 for product.
Computer displays PRODUCT.
2
Computer displays HEADS.
Press button #0 to set head count to "0".
Press ENTER for next step.
3
Computer displays INTERVAL in the left display
and PROD 3 in the right display.
Press button #1 to set Product 3 Interval
#1.
4
Computer displays
COOKTIME.
Enter 9 3 0, in that sequence. Press
ENTER to program cook time of 9
minutes, 30 seconds for interval #1.
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.3 Programming for Hot Wings/Hot BBQ Wings (cont.)
5
Computer displays SET--TEMP.
Enter 3 4 0, in that sequence. Press
ENTER to save 340 °F (171 °C) as set--
temp for interval #1.
6
Computer displays FLEX.
Press button #3 to set flex mode = "3".
Press ENTER to lock in setting.
7
Computer displays INTERVAL in the left display
and PROD 3 in the right display.
Press PROG SCAN to advance to pre-
set alarm program mode.
8
Computer displays
PREALM 1.
Enter 8 3 0, in that sequence. Press ENTER to set alarm to 8
minutes, 30 seconds cook time remaining.
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.3 Programming for Hot Wings/Hot BBQ Wings (cont.)
9
Press PROG SCAN
button to advance to
Exit Cycle program
mode.
Computer displays
PREALM 2.
10
Computer displays EX-CYCLE in the left display
and SET--TEMP in the right display.
Press ENTER button to save default setting of
SET--TEMP.
11
Computer displays INTERVAL in the left display
and PROD 3 in the right display.
Press TEMP button to exit Product #3
programming.
12
Press ON/OFF button to exit
programming mode.
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.4 Programming for Potato Wedges
Enter Programming Mode as outlined in Section 2.2
1
Press
button #4
or #5 for
product.
OR
Computer displays PRODUCT.
2
Computer displays HEADS.
Press button #0 to set head count to "0".
Press ENTER for next step.
3
Computer displays INTERVAL in the left display
and PROD 4 or 5 in the right display.
Press button #1 to set Product 4 or 5,
Interval #1.
4
Computer displays
COOKTIME.
Enter 5 0 0, in that sequence. Press
ENTER to program cook time of 5
minutes for interval #1.
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.4 Programming for Potato Wedges (cont.)
5
Computer displays SET--TEMP.
Enter 3 4 0, in that sequence. Press
ENTER to save 340 °F (171 °C) as set--
temp for interval #1.
6
Computer displays FLEX.
Press button #3 to set flex mode = "3".
Press ENTER to lock in setting.
7
8
Computer displays INTERVAL in the left display
and PROD 4 or 5 in the right display.
Press PROG SCAN to advance to pre-
set alarm program mode.
Computer displays
PREALM 1.
Enter 4 3 0, in that sequence. Press ENTER to set alarm to 4
minutes, 30 seconds cook time remaining.
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.4 Programming for Potato Wedges (cont.)
9
Press PROG SCAN
button to advance to
Exit Cycle program
mode.
Computer displays
PREALM 2.
10
Computer displays EX-CYCLE in the left display
and SET--TEMP in the right display.
Press ENTER button to save default setting of
SET--TEMP.
11
Computer displays INTERVAL in the left display
and PROD 4 or 5 in the right display.
Press TEMP button to exit Product #4 or
5 programming.
12
Press ON/OFF button to exit
programming mode.
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.5 Programming for Sandwiches/Filets
Enter Programming Mode as outlined in Section 2.2
1
Press
button #6
or #7 for
product.
OR
Computer displays PRODUCT.
2
Computer displays HEADS.
Press button #0 to set head count to "0".
Press ENTER for next step.
3
Computer displays INTERVAL in the left display
and PROD 6 or 7 in the right display.
Press button #1 to set Product 6 or 7,
Interval #1.
4
Computer displays
COOKTIME.
Enter 6 3 0, in that sequence. Press
ENTER to program cook time of 6
minutes, 30 seconds for interval #1.
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.5 Programming for Sandwiches/Filets (cont.)
5
Computer displays SET--TEMP.
Enter 3 4 0, in that sequence. Press
ENTER to save 340 °F (171 °C) as set--
temp for interval #1.
6
Computer displays FLEX.
Press button #3 to set flex mode = "3".
Press ENTER to lock in setting.
7
8
Computer displays INTERVAL in the left display
and PROD 6 or 7 in the right display.
Press PROG SCAN to advance to pre-
set alarm program mode.
Computer displays
PREALM 1.
Enter 0 0, in that sequence. Press ENTER to set alarm to zero
minutes cook time remaining.
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.5 Programming for Sandwiches/Filets (cont.)
9
Press PROG SCAN
button to advance to
Exit Cycle program
mode.
Computer displays
PREALM 2.
10
Computer displays EX-CYCLE in the left display
and SET--TEMP in the right display.
Press ENTER button to save default setting of
SET--TEMP.
11
Computer displays INTERVAL in the left display
and PROD 6 or 7 in the right display.
Press TEMP button to exit Product #6 or
#7 programming.
12
Press ON/OFF button to exit
programming mode.
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.6 Programming for Popcorn Chicken
Enter Programming Mode as outlined in Section 2.2
1
Press button #8 for product.
Computer displays PRODUCT.
2
Computer displays HEADS.
Press button #0 to set head count to "0".
Press ENTER for next step.
3
Computer displays INTERVAL in the left display
and PROD 8 in the right display.
Press button #1 to set Product 8 Interval
#1.
4
Computer displays
COOKTIME.
Enter 2 3 0, in that sequence. Press
ENTER to program cook time of 2
minutes, 30 seconds for interval #1.
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.6 Programming for Popcorn Chicken (cont.)
5
Computer displays SET--TEMP.
Enter 3 4 0, in that sequence. Press
ENTER to save 340 °F (171 °C) as set--
temp for interval #1.
6
Computer displays FLEX.
Press button #3 to set flex mode = "3".
Press ENTER to lock in setting.
7
8
Computer displays INTERVAL in the left display
and PROD 8 in the right display.
Press PROG SCAN to advance to pre-
set alarm program mode.
Computer displays
PREALM 1.
Enter 2 0 0, in that sequence. Press ENTER to set alarm to 2
minutes cook time remaining.
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.6 Programming for Popcorn Chicken (cont.)
9
Press PROG SCAN
button to advance to
Exit Cycle program
mode.
Computer displays
PREALM 2.
10
Computer displays EX-CYCLE in the left display
and SET--TEMP in the right display.
Press ENTER button to save default setting of
SET--TEMP.
11
Computer displays INTERVAL in the left display
and PROD 8 in the right display.
Press TEMP button to exit Product #8
programming.
12
Press ON/OFF button to exit
programming mode.
2-22
Download from Www.Somanuals.com. All Manuals Search And Download.
KFC-1 SMS COMPUTER
CHAPTER 3: ADDITIONAL COMPUTER SETTINGS
NOTE: Activation of the
oil management system
is optional. All other
3.1 Programming for Shortening Management
Listed below are procedures for initiating the Shortening Management System software
and setting local time, daylight savings time and stagger between polishings. Setting
Stagger Time prevents frypots in the same battery from entering a “Polish” cycle
simultaneously. Proper computer settings allow maximum performance from the fryer,
resulting in a quality product every time.
features of the KFC-1
SMS remain operational
with the oil management
programming idle.
1
Computer displays CODE
in the left display and
(Blank) in the right
display.
Press ON/OFF button to turn computer OFF.
Press PROG SCAN button to enter CODE.
2
Enter Code #: 1890, in that sequence. This code initializes the Shortening Management System
program, which will become active the next day. Once activated, the system is not readily deactivated.
As each number is entered, dashes appear in the
right display.
3
4
Upon pressing the last number, T-Zone appears in the
left display, Eastern (the default setting) appears in
the right.
Press Temp button
to toggle between
time zones.
With desired time zone shown on right display,
press the enter key to lock in choice.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Setting Daylight Savings Time/StaggerBetween Polishings
1
Computer displays CODE
in the left display and
(Blank) in the right
display.
Press ON/OFF button to turn computer OFF.
Press PROG SCAN button to enter CODE.
2
Enter Code #: 1 6 5 5, in that sequence.
As each number is entered, dashes appear in the
right display. The computer is ready for
programming after the last number is entered.
3
Computer displays DAYLIGHT in the left display
and XXXX in the right display.
Press TEMP button to toggle between
FALL and SPRING. Press ENTER to
lock in choice.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Computer displays STAGGER in the left display
and 0 MIN in the right display.
Press TEMP button to toggle between 0,
15, 30 or 45 MIN. Press ENTER to lock
in choice.
3.3 Setting Local Time
1
Computer displays CODE
in the left display and
(Blank) in the right
display.
Press ON/OFF button to turn computer OFF.
Press PROG SCAN button to enter CODE.
2
Enter Code #: 2 0 0 0, in that sequence.
As each number is entered, dashes appear in the
right display. The computer is ready for time entry
after the last number is entered.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Computer displays SET TIME in left display
and 00:00 in right display.
Enter correct time (military style)
using product selection keys.
Example:
To enter 8:00 AM, enter 0 8 0 0, in that
sequence. Press ENTER to set time.
To enter 4:00 PM, enter 1 6 0 0, in that
sequence. Press ENTER to set time.
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Frymaster, L.L.C.
8700 Line Avenue, Shreveport, Louisiana USA 71106
Service Center (800) 551-8633 or (318) 865-1711
Printed in the United States of America
English
819-5733
02/01
Download from Www.Somanuals.com. All Manuals Search And Download.
|